Beruflich Dokumente
Kultur Dokumente
WARNING
This service information is designed for experienced repair technicians only and is not intended for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products dealt within this service information by anyone else could result in serious injury or death.
2006 Panasonic Communications Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. Published in Japan.
General Annotations
9. Important Notice (Especially in those countries belonging to the European Union): This product is fully compliant with the national laws transposed from the EU Directive on the restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment, effective 1st July 2006 in the EU countries. In order for the product to comply with the RoHS Directive, the six particular substances (lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls, and polybrominated diphenyl ethers) have been either totally eliminated or limited to the concentration level below maximum allowed. Consequently spare parts have been changed to RoHS-compliant parts where applicable. To ensure compliance with the spare parts application of the RoHS legislation, please make sure to follow the details provided in this manual when ordering spare parts and carrying out repairs.
The contents of this Service Handbook, and the Specifications are subject to change without notice. Panasonic Communications Co., Ltd. reserves the right to make improvements in the product design without reservation and without notice. Published in Japan.
Important Notice
Please read these Instructions completely BEFORE installing any optional accessories. Installing the additional board, or connector with the power ON (only the power switch OFF) could damage the SPC, and/or SC board. If the Hard Disk Drive Unit is installed, to prevent a Disk Scan Function from being performed (similar to when the power is abruptly interrupted to the PC), it is important to follow the step sequence below when turning OFF the Power Switch on the machine.
<Example : DP-8020>
1. If the machine is in the "ENERGY SAVER (Shutdown Mode)", you may turn the Power Switch on the machine to the OFF position. If it is not in the "ENERGY SAVER (Shutdown Mode)", continue to step 2 below. 2. Press "FUNCTION" and "ENERGY SAVER" keys simultaneously first. 3. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk Drive Unit, and advances into "ENERGY SAVER MODE". 4. Turn the Power Switch on the machine to the OFF position. 5. Disconnect the Telephone Line Cable, if the Fax Option is installed. 6. Unplug the AC Power Cord.
(When the Fax option is installed, there is a remote possibility of electrocution when servicing the unit during a Lightning Storm. As a precaution, disconnect the Telephone Line Cable first, before unplugging the AC Power Cord.
WARNING
This service information is designed for experienced repair technicians only and is not intended for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products dealt within this service information by anyone else could result in serious injury or death. * The specifications are subject to change without notice. Panasonic Communications Co., Ltd. reserves the right to make improvements in the product design without reservation, and without notice.
Caution:
Depending on your machines model, it may weight approximately 93.26 - 98.33 lb (42.3 - 44.6 kg) without any options. To prevent injuries, use the appropriate number of personnel to lift, or move the machine as illustrated. Do not lift the machine by the Paper Tray as it may cause damage and/or bodily injury.
Precautions
For Your Safety
To prevent severe injury and loss of life, read this section carefully before servicing the Panasonic machine to ensure proper and safe operation of your machine. Please ensure that the machine is installed near a wall outlet and is easily accessible. This section explains the Warnings and Cautions used in the machine and/or this manual.
WARNING: Denotes a potential hazard that could result in serious injury or death. CAUTION: Denotes hazards that could result in minor injury or damage to the machine.
This section also explains the Warnings and Cautions used in the machine and/or this manual. These symbols are used to alert operators to a specific operating procedure that must not be performed. These symbols are used to alert operators to a specific operating procedure that must be emphasized in order to operate the machine safely.
Once a month, unplug the machine and check the power cord for the following. If you notice any unusual condition, contact your authorized Panasonic dealer . The power cord is plugged firmly into the receptacle. The plug is not excessively heated, rusted, or bent. The plug and receptacle are free of dust. The cord is not cracked or frayed.
Operating Safeguards
Do not touch areas where these caution labels are attached to, the surface may be very hot and may cause severe burns. Do not place any liquid container such as a vase, or coffee cup on the machine. Spilt water can cause fire or shock hazard. Do not place any metal parts such as staples or clips on the machine. If metal and flammable parts get into the machine, they can short-circuit internal components, and cause fire or electric shocks. If debris (metal or liquid) gets into the machine, switch Off and unplug the machine immediately. Operating a debris-contaminated machine can cause fire or electric shock. Do not try to alter the machine configuration or modify any parts. An unauthorized modification can cause smoke or fire.
Consumable Safeguards
Never dispose of toner, toner cartridge, or a waste toner container into an open flame.Toner remaining in the cartridge/bottle can cause an explosion, burns and/or injuries. Keep button batteries/stamp out of the reach of children to prevent chocking or poisoning. If a button battery/stamp is swallowed accidentally, get medical treatment immediately,
When moving the machine, be sure to unplug the power cord from the outlet. If the machine is moved with the power cord attached, it can cause damage to the cord which could result in fire or electric shock.
Consumable Safeguards
Never heat the drum cartridge, or scratch its surface. A heated, or scratched drum can be hazardous to your health. Do not mix new and old batteries together, as they can burst or leak, causing a fire or injuries. Be sure to use the specified type of batteries only. . Ensure that batteries are installed with correct polarity. Incorrectly installed batteries can burst or leak, resulting in spillage or injuries.
Others
When clearing a paper jam or other fault, follow the appropriate procedure given in this manual. The machine has a built-in circuit for protection against lightning-induced surge current. If lightning strikes in your neighborhood, maintain an ample distance from the machine, and do not touch it until the lightning stops. If you notice flickering, distorted images, or noises on your audio-visual units, your machine may be causing radio interference. Switch it Off, and if the interference disappears, the machine is the cause of the radio interference. Perform the following procedure until the interference is corrected. Move the machine, and theTV and/or radio away from each other. Reposition or reorient the machine, and theTV and/or radio. Unplug the machine, TV and/or radio, and replug them into outlets operating on different circuits. Reorient the TV and/or radio antennas, and cables until the interference stops. For an outdoor antenna, ask your local electrician for support. Use a coaxial cable antenna.
10
11
12
Table of Contents
Specifications ........................................ 14
1.1. 1.2. 1.3. 1.4. 1.5. Control Panel ..........................................14 Specifications Table................................16 Fax, Printer and Internet Fax Functions .........................................26 System Combination...............................37 Options List.............................................38 5.14. Paper Tray ........................................... 246 5.15. Automatic Document Feeder ............... 248 5.16. Inverting Automatic Document Feeder (For DP-8020E) .................................... 256 5.17. PC Boards/Harnesses.......................... 274 5.18. 2nd/4th Paper Tray .............................. 280 5.19. 3rd Paper Tray ..................................... 286 5.20. Packing and Accessories 1. For USA and Canada ...................... 292 5.21. Packing and Accessories 2. For China ......................................... 294 5.22. Packing and Accessories 3. For Other Destinations (except USA, Canada and China) ........ 296 5.23. Printer Controller Module for PCL6 ............................................... 298 5.24. Printer Controller Module for PS/PCL6 ......................................... 300 5.25. Fax Communication Board................... 302 5.26. Keyboard Option .................................. 306 5.27. Hard Disk Drive Unit............................. 308 5.28. Accounting Software ............................ 310 5.29. i-ADF Packing and Accessories ........... 312 5.30. ADF Packing and Accessories ............. 314 5.31. 2nd/4th Paper Tray and 3rd Paper Tray Packing and Accessories .......................................... 316 5.32. Dehumidifier Heater Kit (For Main Unit) ..................................... 318 5.33. Dehumidifier Heater Kit (For Optional Paper Tray(s)) ................ 320 5.34. Key Counter Harness Kit ..................... 322 5.35. Hardware Identification Template ........ 324
5.10. Hopper Unit...........................................232 5.11. Developer Unit ......................................234 5.12. Drum Unit..............................................238 5.13. Drive Unit ..............................................242
13
DP-8020E/8020P/8016P
1 Specifications
1.1. Control Panel
DP-8020 Series for PU (USA/Canada, etc.)
DP-8020E
DP-8020P
DP-8016P
Note1: 1. DP-8020P is not available for USA and Canada. 2. Model availability may differ as per destination. Please ask your sales company for details. Note2: LCD Display Brightness Adjustment To adjust the brightness of the LCD display, press and while holding down the "CLEAR" key, keep pressing the "ORIGINAL SIZE", or the "COPY SIZE" key until the desired brightness is achieved. ORIGINAL SIZE: Dimmer COPY SIZE : Brighter
14
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
DP-8020P
DP-8016P
Note: Model availability may differ as per destination. Please ask your sales company for details.
15
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
1.2.
1.2.1.
Specifications Table
Copy Function
Items Description DP-8020E DP-8020P DP-8016P Desktop Fixed Left / Rear Left / Center Center Face Down Organic Photo Conductor (OPC) Dry Electrostatic System Dry Dual Components No Heat & Pressure Ledger (11 x 17 in) / A3 (297 x 420 mm) Paper Size LDR, LGL, LTR, LTR-R, INV-R A3, A4, A4-R, A5, A5-R, B4, FLS A3, A4, A4-R, B4, B5, B5-R LDR, LGL, LTR, LTR-R, INV-R Bypass Tray A3, A4, A4-R, A5-R, B4, FLS A3, A4, A4-R, B4, B5, B5-R #10 (4.1 x 9.5 in) DL (4.3 x 8.7 in) 16-24 lb (60 - 90 g/m2) 15-34 lb (55 - 133 g/m2) 17-24 lb (64 - 90 g/m2) Less than 30 sec Remarks
Basic Specifications 1 Type 2 Platen 3 Original Position Platen ADF / i-ADF 4 Recording Paper Path 5 Face Up / Face Down 6 Drum 7 Copy Process 8 Developing Process 9 Toner Recycle 10 Fusing System 11 Max Original Size 12 Paper Tray
Bypass Tray (Envelope) 13 Paper Weight Paper Tray Bypass Tray ADU 14 Warm-up Time
For USA and Canada For EU FLS = 8 x 13 in, 8.5 x 13 in For Other Destinations For USA and Canada For EU FLS = 8 x 13 in, 8.5 x 13 in For Other Destinations For USA and Canada For EU
For DP-8020E 68 F (20 C) From Platen, Letter/ A4 Portrait,1st Paper Tray. Period between Start Key is pressed and Paper ejected to the Exit Tray. When LSU is ready.
16 Copy Speed Ledger A3 Legal / B4 / FLS Letter-R / A4-R Letter / A4 Invoice-R / A5-R
From Platen, 1st Paper Tray, and Paper ejected to the Exit Tray, LSU is ready, and Continuous Copy.
16
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Items
Remarks
17 Zoom Enlargement Selected Original size / Copy size Reduction Selected Original size / Copy size Zoom 50 - 200% 18 Paper Feed Front Loading Universal Paper Tray Paper Tray Capacity 550 sheets x 1 Auto Size Setting No Low Level Warning Empty Only Bypass Paper Tray Capacity 50 sheets Auto Size Setting Yes Paper Capacity 600 sheets (Std. Configuration) 19 Multi Copy Range 999 sheets 20 Gradation Text Bi-Level Text / Photo 256 steps Photo 256 steps 21 Resolution 600 dpi 22 Standard Sorting Memory 16 MB Size 23 Standard Page Memory 32 MB Size 24 Exit Tray Capacity Standard: 250 sheets 25 Color No 26 Dimensions 22.0 x 21.9 x 18.1 in (558 x 557 x 460 mm) (W x D x H) 33.2 x 24.6 x 24.5 in (844 x 624 x 623 mm) 27 Operating Space 33.2 x 22.2 in (W x D) (844 x 565 mm) DP-8020E DP-8020P*/ 8016P/ DP-8020E DP-8020P/ 8016P 95.46 lb (43.3 Kg) 93.26 lb (42.3 Kg) 98.33 lb (44.6 Kg)
1% Step
Includes Bypass Paper Tray. For PU (USA/Canada, etc.) *DP-8020P is not available for USA and Canada
Weight
17
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Items Options 1 Paper Feed System 550 sheets 2nd Paper Tray Paper Size Detection Low Level Paper Warning 550 sheets 3rd Paper Tray Paper Size Detection Low Level Paper Warning 550 sheets 4th Paper Tray Paper Size Detection Low Level Paper Warning Max. Paper Capacity 2 Stand Stand for 4*-Paper Tray Configuration
Yes Manual Empty Only Yes Manual Empty Only Yes Manual Empty Only 2, 250 sheets 1, 150 sheets Low Stand with Casters DA1D18C (For USA and Canada Only) DA-DA191-PE (For Other Destinations) Low Stand with Casters DA1D18C (For USA and Canada Only) DA-DA190-PE (For Other Destinations) Mid Stand with Casters DA1D18B (For USA and Canada Only) DA-DA189-PE (For Other Destinations) High Stand with Casters DA1D18A (For USA and Canada Only) DA-DA188-PE (For Other Destinations) No Control Panel Selectable No Control Panel Selectable Control Panel Selectable
Option
Option
Option
Option
Note: The same Stand (DA1D18C) is used for either 3 or 4 Paper Tray Configuration for USA and Canada. Option For USA and Canada 3 Platen Cover Standard For EU and Other Destinations Free Stop Yes From 30 to 70 degrees.
18
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Items 4 ADF Single Side Type Original Set Scanning Method Capacity (Originals) SADF Mode Free Stop 5 Inverting ADF (i-ADF) Duplex Type Original Set Scanning Method Capacity (Originals) SADF Mode 6 Free Stop Exit Tray (Inner) Tray Position Number of Bins Face Up / Face Down Bin Capacity Multi Tray Function Shift Tray Function Finisher Exit Tray (Outer) Automatic Duplex Unit Counter Key Counter Capability 11 Dehumidifier 12 Sorting Image Memory Optional Image Memory 1 (16MB) Optional Image Memory 2 (64MB) Optional Image Memory 3 (128MB)
Description DP-8020E DP-8020P DP-8016P Option Face Up Sheet Through 50 sheets Yes Yes Option No Face Up Sheet Through 50 sheets Yes Yes Inner 1 Face Down 250 sheets No No No No Standard : DP-8020E Option Option Yes Yes Yes
Remarks
LTR / A4 : 20 lb (75 g/m2) Available for single side scanning only. From 30 to 70 degrees.
7 8 9 10
The Harness Kit contains only Harnesses, Bracket and a Screw. Supplied as a Service Part.
Unit comes standard with 16 MB. 1-Slot available for an Optional Image Memory module. Additional Optional Sorting Image Memory (Minimum 16 MB) is required for the Hard Disk Drive to function. (For Tandem, Remote Copy, etc.)
Option
19
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Items Features 1 Automatic Features Auto Magnification Selection Auto Paper Selection Auto Paper Tray Selection Auto Start
Remarks
Remote Diagnostic Machine Stops when Out of Toner 2 Additional Features Low Level Paper Warning Photo Mode Original Detection Release Edit / Effects Book Mode Edge Mode Margin Mode X-Y Zoom Stamping / Page Numbering Inverse Mode (Negative / Positive) Centering Mode Image Repeat Mirror Mode Others (Inverting ADF & ADU) 2-Page Copy Mode 2 in 1 4 in 1 6 in 1 8 in 1 Booklet Mode
Yes
Reservation while Power On Initializing. Requires the Fax Communication Board (DA-FG180) option or the Internet Fax / E-MAIL Module (DA-NF180) option. PPC Function
Yes Empty Only Yes No Yes Yes Yes No No No Yes Yes No Yes Yes Yes No No No
256 steps Manually overridden when using the Original Size keys.
20
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Items Duplex Copy 12 21 22 Book2 1st Page BLANK 1st Page IMAGE Image Rotation (90 or 270 ) Electronic Sorting Rotation Sorting Insertion Job Cover Mode Page Insertion Mode OHP Interleave Mode Presentation Mode Department Counter ADF Multi Size Feed JOB Build and SADF Mode Original Counter Job Memory Job Time Display Concurrent Copy Tandem Copy Mode Remote Copy Mode Scan Once Print Many Mode Job Complete Notice Trial Copy Mode Weekly Timer Function Mode Interrupt Electronic Counter Digital Sky Shot Mode Double Exposure 3 Control Panel Display Status Lamp
Description DP-8020E DP-8020P DP-8016P Yes Yes Yes Yes No No Yes Yes Yes No No No No Yes No Yes No Yes Yes Yes No No Yes Yes No No Yes Yes Yes Yes Yes LCD Yes No No No No
Remarks
300 Departments
21
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Items Key Original Size Copy Size Keypad Clear Stop Start Energy Saver Multi Size Feed Sort Function Mode Original Detection Release Interrupt Reset One-Touch key Mode Change LCD Main Indication Message Language (Default) Original Size / Image Indication Paper Size / Image Indication Paper Tray Selection Selected Paper Tray / Tray Status Original Mode Selection Copy Density Selection Setting Confirmation Function Classification Zoom Magnification Number of Copies JOB Build and SADF / Multi Size Feed Mode Error Code Finishing Warning Indicators Add Toner Toner Waste Container Full Add Paper (No Paper) Add Paper (Under 50 sheets)
Description DP-8020E DP-8020P DP-8016P Yes Yes Yes Yes Yes Yes Yes No Yes Yes No Yes Yes Yes Yes English (American) Specified Language Yes (without Image) Yes (without Image) Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes No
Remarks
With Keyboard Option Copier / Printer / NW Scanner / Fax and Internet Fax Mode For USA and Canada For EU and Other Destinations
22
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Description DP-8020E DP-8020P DP-8016P Paper Jam Indication Yes Paper Jam Location Yes Service Alert Call Yes User Error Yes Machine Error Yes History of Jam Errors Yes 4 Main Unit Total Counter Electronic Yes Items Mechanical Max. Weight of Documents on the Platen Glass ADF with Document Guide Clip Pocket Operating Instructions Pocket Warning / Caution Label 5 Optical System Original Detection Method Scanning Method Dehumidifier Mechanical Multi Copy Mode 6 Process System Type Toner Toner Waste Container Drum Life Developer Life Dehumidifier Manual Add Toner Yes
Remarks
11.02 lb (5 kg) Yes Yes No Specified Language Reflective Photo Sensor Type 600 dpi CCD Yes No Separate OPC Unit and Developer Unit Type 10 K 10 K 60 K 60 K Yes Yes Supplied as a Service Part
User replacement
Supplied as a Service Part Manually adds toner to the developer (up to TDC threshold)
23
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Remarks
120 K 60 K 28.5 x 29.7 x 28.6 in (725 x 755 x 726 mm) 29.5 x 31.3 x 29.7 in (750 x 796 x 755 mm) 28.7 x 29.3 x 25.8 in (730 x 745 x 655 mm) 127.77 lb 125.56 lb (58 kg) (57 kg) 143.187 lb 140.98 lb (65 kg) (64 kg) 112.35 lb 110.14 lb (51 kg) (50 kg) Yes No No No Yes 99 - 132 VAC 47 - 63 Hz Single phase 180 - 264 VAC 47 - 63 Hz Single phase 120 VAC 220 - 240 VAC For USA, Canada For China For EU and Other Destinations For USA and Canada For China For EU and Other Destinations
1 Packing Dimension
2 Packing Weight
3 Accessories Process Unit Developer Toner Toner Waste Container Operating Instructions Power Supply 1 Power Requirement 2 Power Consumption Max.Power Consumption 100 VAC PS 220 VAC PS Standby 100 VAC PS 220 VAC PS Energy Saver Power Saver Mode 100 VAC PS 220 VAC PS Sleep Mode 100 VAC PS 220 VAC PS Shutdown Mode 100 VAC PS 220 VAC PS
Less than 1.3 KW Less than 1.3 KW 120 W 120 W Turns On the Heater Power. Automatically enters the Sleep or Shutdown Mode after 10 minutes from the Standby or Energy Saver Mode. Manually enters the Energy Saver Mode by pressing the Energy Saver key. Sleep or Shutdown mode is controlled by the General Functions setting. Network Function not available
1.4 W 1.6 W
24
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Description DP-8020E DP-8020P DP-8016P 50 - 80 F / 10 - 30 C 30 - 80% RH UL60950-1 / CSA C22.2 No.609501 EN60950-1 / IEC60950-1 Energy Star Compliant Class A computing device in FCC Rules Part 15 Class B EN55022, EN55024, EN61000-3-2, EN61000-3-3, CISPR22 This Product uses Lead Free (PbF) PCBs
Remarks
For USA and Canada For EU and Other Destinations For USA and Canada
5 EMI
25
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
1.3.
1.3.1.
Main Specifications 1 Compatibility 2 PSTN Line Port 3 Leased Line Port 4 V.24 Line Port 5 Modem Speed 6 Coding Scheme 7 ECM 8 Short Protocol 9 Transmission Speed
Transmission Std. : 203 x 98 (8 x 3.85) Fine : 203 x 196 (8 x 7.7) S-Fine : 203 x 391 (8 x 15.4) 406 x 391 (16 x 15.4) 10 Communication Resolution 600dpi : 600 x 600 dpi dpi x lpi (pels/mm x lines/ Reception mm) Std. : 203 x 98 (8 x 3.85) Fine : 203 x 196 (8 x 7.7) S-Fine : 203 x 391 (8 x 15.4) 406 x 391 (16 x 15.4) 600dpi : 600 x 600 dpi Scanner Mechanism 1 Scanning Device CCD (ADF / Platen) 2 Scanning Speed (ADF) Resolution Vertical Horizontal Std: 203 x 98 (8 x 3.85) dpi x lpi (pels/mm x lines/ mm) 0.9 / 1.0 sec 0.7 sec Fine: 203 x 196 (8 x 7.7) dpi x lpi (pels/mm x lines/ mm) S-Fine: 406 x 391 (16 x 15.4) dpi x lpi (pels/mm x 1.8 / 2.0 sec 1.4 sec lines/mm) 600dpi: 600 x 600 2.8 sec 2.1 sec 3 Scanning Speed (Platen) Resolution Vertical Horizontal 600dpi: 600 x 600 2.8 sec 2.1 sec Std. : 203 x 98 (8 x 3.85) 4 Scanning Resolution Fine : 203 x 196 (8 x 7.7) dpi x lpi (pel/mm x lines/ S-Fine : 203 x 391 (8 x 15.4) mm) 406 x 391 (16 x 15.4) 600dpi : 600 x 600 dpi
600 dpi communication is only possible between T.30 Compliant Panafax, WORKiO, and other T.30 compliant machines.
LTR / A4, Scanned in Vertical or Horizontal Direction. Excluding Initializing Time and ADF slipping factor.
26
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Items 5 Document Size (Max.) 6 Effective Scanning Width 7 A3 size TX/RX 8 Reduction XMT 9 ADF Capacity 10 Collation Stack Printer Mechanism 1 Recording Method 2 Recording Speed 3 Recording Resolution Fax
Description DP-8020E DP-8020P ADF: LDR / A3 LDR (11.5 in) / A3 (292 mm) Yes Yes 50 sheets Yes LP 23 / 30 ppm (A4 Horizontal) 600 x 600 dpi
Remarks
Conforms to ITU-T A3 LDR to LTR / A3 to B4 / A3 to A4 / B4 to A4 Face-Up, feed from top page LTR / A4 (20 lb / 75 g/m2) Face Down
Recording Speed attained after the 1st copy. Invoice : Not supported. Ledger size is transmitted as A3 size for N. American models. If A3 is received, approx. 1" of image on both edges are not printed on Ledger size paper. Conforms to ITU-T A3 Optional max. 2250 sheets LTR / A4 : 20 lb (75 g/m2) Face Down
5 Effective Printing Width 6 Recording Paper Capacity 7 Collation Stack 8 Consumable Fax Memory 1 Standard Memory 2 Optional Memory Dual Operation 1 Multi Task Operation 2 Direct XMT Reserve 3 Memory XMT Reserve 4 Number of Memory Job Files
11.4 in (289 mm) 600 sheets Yes Toner Bottle, Developer, OPC Drum 2 MB (120 pages) 4 MB 8 MB Yes Yes Yes Yes
Flash ROM, ITU-T Image No.1 (A4, Std Resolution) Expansion Flash Memory Card, using ITU-T Image No.1 (A4, Std Resolution)
Max. 50 files
27
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Items Dialing/Telephone Features 1 One-Touch Keys 2 One-Touch / Program Keys 3 One-Touch Auto Dialers 4 Abbr. Auto Dialers 5 Total Auto Dialers 6 Directory Search Dialing 7 Max. Tel Number Digits 8 Max. Station Name Characters 9 Full Number Dialing (Buffered Dialing) 10 Direct Dialing (Monitor Dialing) 11 Automatic Redialing 12 Manual Redialing 13 14 15 16 17 18 Line Monitor Speaker Chain Dialing (Hybrid Dial) Pulse / Tone Dialing Pulse to Tone Change Flash Key Handset
Description DP-8020E DP-8020P 28 4 32 200 232 Yes 36 15 Yes Yes Yes Yes Yes Yes Yes No Yes No
Remarks
Plus an additional 800 stations available to select from, when the optional Hard Disk Drive (DAHD18) is installed.
Max. 50 stations Voice mode Up to 15 times at 0 to 15 min. intervals Pressing the REDIAL/PAUSE button In Monitor Dialing mode only 10 pps / DTMF
28
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Items Transmission Features 1 Direct Transmission 2 Memory Transmission 3 Quick Memory Transmission 4 Multi-Station Transmission (Sequential Broadcasting) 5 Direct Deferred Transmission 6 Deferred Transmission 7 Deferred Multi-Station Transmission 8 Priority Direct Transmission 9 Priority Memory Transmission 10 Batch Transmission 11 90 Degree Rotation Transmission 12 Cover Sheet 13 Confidential Mail Box 14 Multi-Copy Transmission 15 Memory Back-Up 16 Duplex Scanning Reception Features 1 Substitute Reception 2 Fixed Reduction
Description DP-8020E DP-8020P Yes Yes Yes Yes No Yes Yes Yes No Yes Yes Yes No No Yes Yes Yes Yes
Remarks
Page Retransmission
FAX : Back-up with Flash Memory. Copy / Printer : No Back-up with D-RAM With Inverting ADF (i-ADF)
3 Auto Reduction 4 Overlap Printing 5 Receive to Memory 6 Distinctive Ring Detector (DRD) 7 90 Degree Rotation Reception 8 Duplex Printing
LTR/A4/LGL: 70 - 100% (in 1% Steps), Top & Left Alignment LTR/A4/LGL: 70 - 100% (in 1% Steps), Top & Left Alignment Page End Approx. 0.51 in (13 mm)
29
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Items Polling 1 Polling 2 Turnaround Polling 3 Multi-Station Polling 4 Deferred Polling 5 Deferred Multi-Station Polling 6 Direct Polling Tx 7 Memory Polling Tx 8 Preset Polling Password 9 Temporary Polling Password 10 Continuous Polling Convenience 1 Panel Display 2 Voice Contact 3 Edit File Mode 4 Incomplete File Save 5 Automatic Cover Sheet Certainty 1 Verification Stamp 2 Header / Total Page Print 3 Transaction Journal 4 Comm. Journal 5 Last Ind. XMT Journal List Printouts 1 One-Touch List 2 ABBR. No. List 3 Program List 4 Address Book Search List 5 Fax Parameter List 6 File List 7 Ind. XMT Journal 8 Directory Sheet
Description DP-8020E DP-8020P Yes No Yes Yes Yes No Yes Yes Yes Yes LCD No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No
Remarks
Max. 250 stations Max. 50 timers Max. 50 timers / 250 stations 1 File
30
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Items Identifications 1 Logo 2 Multiple Logo 3 Character ID 4 Numeric ID Special Communications 1 Password XMT / RCV 2 Selective Reception 3 Relay XMT Request 4 Relay XMT Center 5 Confidential XMT / Polling 6 Confidential Center 7 Mailbox XMT / Polling 8 Mailbox Center 9 File XMT 10 Fax Forward 11 Sub-Address XMT 12 Sub-address RCV 13 OMR-XMT Others 1 Fax Access Code 2 PIN Code Access 3 Intelligent Redial (AI) 4 Department Code 5 Power Saver Mode 6 Self Diagnostic Function 7 Remote Diagnostic Function 8 Check & Call Function 9 V.24 / Encryption Interface
Description DP-8020E DP-8020P Yes No Yes Yes No No No No No No No No No Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes No
TSI Check
31
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
1.3.2.
Printer Function
Items Description DP-8020E/P DP-8016P No Ethernet 10Base-T/ 100Base-TX Yes No Letter / Legal / Ledger / A3 / A4 / A5 / B4 / B5 / FLS1 / FLS2 / Invoice / 8K / 16K Additionally; Envelope #10 / Envelope DL / Custom Size (PCL / PS only) No 300 x 300 600 x 600 1200 (Equivalent) x 600 (PCL / PS only) USB / Ethernet Win 98 / Me / Win NT 4.0 / Win 2000 / XP / Windows Server 2003 / MAC 8.6-10.4 20 MB Yes Yes Yes Yes Yes Yes No Yes Yes IBM PC, AT or Compatible, MAC Yes Yes Yes Yes No No Remarks
Interface 1 Centronics Parallel I/F 2 LAN (Network) 3 USB Port 4 IEEE-1394 Printer Function 1 Printing Size (Paper Tray) 2 Printing Size (Multi-Purpose Tray) 3 Stapling 4 Printing Resolution (dpi) 5 Interface 6 OS 7 Printer Work Memory Size 8 GDI 9 PDL (PCL6) 10 PDL (PS3) 11 Duplex Printing 12 Collation Stack 13 Status Monitor Network USB 14 Network Printing 15 Smoothing 16 Applicable PC 17 Multi-Task Operation Printing while Fax-XMT from Memory Printing while Fax-RCV into Memory Fax-XMT from Memory while Printing Fax-RCV into Memory while Printing
USB
MAC 8.6-10.4 is PS only. Not expandable Requires Optional PCL6 Emulation Kit. Requires Optional PS / PCL6 Emulation Kit DP-8020E only. Custom Size/Post Card Size is not available.
MAC is PS only.
32
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Remarks
20 Mailbox
Yes
21 Secure Mailbox
Yes
Requires Optional PCL6 or PS / PCL6 Emulation Kit Requires Optional HDD Unit. Max. 100 Users. Max. 20 mailboxes for each User ID Requires Optional HDD Unit. Max. 100 Users. Max. 20 mailboxes for each User ID
33
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
1.3.3.
Interface 1 Centronics Parallel I/F 2 LAN (Network) 3 USB Port 4 IEEE-1394 Network Scanning Function 1 Scanning Device 2 Scanning Speed (ADF / I-ADF) 3 Halftone 4 Max. Document Size 5 Scanning Resolution (dpi) 6 OS 7 2-Sided Scanning 8 File Format 9 Completion Notice 10 Protocol Network Address Features 1 One Touch Address Keys 2 Abbr. Address Numbers
With i-ADF. TIFF can also be converted to PDF with the PDMS Software Auto Pop-up on the PC Screen (requires Network Status Monitor - installed with PDMS Software)
32 60
34
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
1.3.4.
Main Specifications 1 Communication Protocols 2 Max. Modem Speed 3 Coding Scheme 4 File Format 5 Line Interface Scanner Mechanism 1 Max. Document Size 2 Effective Scanning Width 3 Scanning Resolution dpi x lpi (pel/mm x lines/mm) Printer Mechanism 1 Printing Resolution 2 Effective Recording Width Transmission Features 1 Multi-Task Operation 2 Memory Transmission 3 Sequential Multi-Station Transmission 4 Simultaneous Multi-Station Transmission 5 Sender Selection 6 G3 / Email Mixed Broadcasting 7 Deferred Transmission 8 Fax Forward 9 Sub-address RCV 10 Mail Header Email Header Print Selection Subject Line
LAN: 600 dpi, 16 x 15.4 Scanning Resolution is available with Parameter setting
35
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Items LAN Features 1 Internet Fax Communication 2 Internet Mail Reception 3 Internet Fax Server Features Internet Fax Relay XMT Email Relay MXT Received Fax / Email Forward PC to FAX Transmission Inbound Routing Phone Book Registration from PC Internet Fax Parameters Registration via Email Internet Delivery Confirmation Network Scanning Network Printing LPR / LPD GDI PDL 8 DHCP Client 9 LDAP 10 TIFF Viewer Certainty 1 Comm. Journal (w / Image) ID 1 Email Address
Description DP-8020E DP-8020P Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes With MDN 600 dpi
Internet Fax Internet Fax G3FAX PC Internet Fax G3FAX Local print available Using Sub-Address. Local print available Via Email
4 5 6 7
600 dpi 600 dpi Requires Optional PCL6 or PS Emulation Kit Lightweight Directory Access Protocol Selectable, PDMS / TIFF Viewer
36
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
1.4.
System Combination
ADF
Panel
(PNL PC Board)
SPC PC Board
37
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
1.5.
Options List
Option Number Remarks DA-PC820 Printer Controller for PCL6* Printer Controller for PCL6/PS3* DA-MC820 For DP-8020E/8020P* only DA-FG180 G3 Fax Communication DA-KB180 Additional Optional Sorting Image Memory (Minimum 16 MB) is required for the Hard DA-HD18 Disk Drive to function. (For additional 800 address book, etc.) DA-EM600 F-ROM Board (8 MB) UE-410047 Additional Memory for Fax / Internet Fax UE-410048 DA-SM16B For Electronic Sorting DA-SM64B DA-SM28B DA-WA10 For Accounting Function DA-UC200 Available in Specified Destinations DA-AS181 DA-AR202 For DP-8020E DA-DS184 4th Paper Tray is for DP-8020E only. DA-DS185 3rd Paper Tray is for DP-8020E only. DA1D18A For USA and Canada Note: DA1D18B The same Deluxe Stand (DA1D18C) is used for either 3 or 4 Paper Tray DA1D18C Configuration. DA-DA188-PE DA-DA189-PE Available in Specified Destinations DA-DA190-PE DA-DA191-PE DA-KH180
Options Option Name Printer Controller Module (PCL) Multi Page Description Language Controller Module (PCL/PostScript) Fax Communication Board Keyboard Option Hard Disk Drive Unit Expansion Board Expansion Flash Memory Card, 4 MB Expansion Flash Memory Card, 8MB Image Memory (16MB) Image Memory (64 MB) Image Memory (128MB) Accounting Software Platen Cover Automatic Document Feeder Inverting Automatic Document Feeder 2nd / 4rd Paper Tray 3rd Paper Tray Deluxe Stand (High) Deluxe Stand (Mid) Deluxe Stand (Low) Stand (1-Paper Tray Configuration) Stand (2-Paper Tray Configuration) Stand (3-Paper Tray Configuration) Stand (4-Paper Tray Configuration) Key Counter Harness Kit
Note: 1. PCL6 is a Page Description Language of the Hewlett-Packard Company. 2. PS3 is a Page Description Language of the Adobe Systems Company. 3. Availability may differ as per destination. Please ask your sales company for details. Supplies Part Name Toner OPC Drum Developer Part Number DQ-TUJ10K-PU DQ-TUJ10K-PK DQ-TU10J-PB DQ-H60J DQ-Z60J Remarks For PU (USA/Canada, etc.), 10K For China, 10K For EU and Other Destinations, 10K 60K 60K
Note: Availability may differ as per destination. Please ask your sales company for details.
38
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
39
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Laser Handling Precautions The optical laser system employed by this photocopier is completely sealed by a protective housing, and an external cover. Therefore, the laser beam will not stray or leak during photocopying operation. However, when servicing the photocopier, take the following precautions: 1. Do not insert any screwdrivers, or other tools that have high reflective properties into the laser's path. 2. . Before servicing the machine, remove watches, rings, or other metallic objects that you may be wearing. (This is to avoid the danger of the laser striking the eye by reflecting off the metallic objects being worn.) Since the laser beam cannot be seen with the naked eye, for maximum safety, please follow the above precautions.
40
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.2.
Required Tools
No. Tools 7 Pliers 8 Cotton Swab 9 Brush KS-660 - Conductive Grease 10 (Available from Shin-Etsu Silicones of America, Inc. URL: http://www.shinetsusilicones.com) Molykote EM-50L Grease 11 (Available from Dow Corning, URL: http://www.dowcorning.com)
No. Tools 1 Soft Cloth 2 Isopropyl Alcohol 3 Phillips Screwdriver (#2) 4 Stubby Phillips Screwdriver (#2)
5 6
2.2.1.
No. 1
3 4 5
Check & Clean Check & Clean Check & Clean Check
Inspection Items
7 8
Gears, Rollers Shafts Check & Grease Timing Belts Check & Clean
41
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.3.
i-ADF
12
ADF
16
44
DETAIL A
45
42
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
29 31
30
28 35 32, 33, 34
DETAIL A
43
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.4.
The chart outlined below is a general guideline for maintenance. Cleaning Cycle Method (Sheet) 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K 60K Water 1 Water 1 Water 1 Water 1 Water 1 Water 1 Water 1 Water 1 Water 1 Water Dry soft cloth Water 1 Water 1 Water
1 1
No.
Ref. No.
Replacement/Adjustment Cycle Procedure (Sheet) 120K 120K 120K 120K 120K 120K 60K 120K 120K 120K 120K 120K 120K 120K 120K 120K Refer to 2.2.9.of the Service Manual Refer to 2.2.4.of the Service Manual Refer to 2.2.2.of the Service Manual Refer to 2.2.1.of the Service Manual
1 2 3 4 5 6 7 8 9 11
ADF Roller Pre Feed Roller Separation Roller Torque Limiter Spring ADF Unit Exit 1 Roller White Sheet Feed Roller Pre Feed Roller Paper Feed Roller
2314 2018 2509 2511 1812 1814 2010 2018 2024 2001
F7-08
10 Separation Rubber
12 Scanning Pad 1822 Scanner Unit 13 Mirror 1 415 14 Mirror 2 421 15 Platen (L) Glass 106 16 Scanning (S) Glass 110 2nd, 3rd & 4th Paper Trays 17 Pickup Roller 18 Separation Roller 19 Torque Limiter 1 20 Feed Roller 21 Intermediate Roller Sheet Bypass 22 Feed Roller 23 Separation Roller 24 Torque Limiter 2 25 Registration Roller Bias Transfer Unit 26 Bias Transfer Roller (BTR) 27 Duplex Feed Roller Process Unit Developer 689 658 691 601 711 735 1403 619 629 690 623 3104
F7-04
F7-11
Refer to 2.2.8.of the Service Manual Refer to 2.2.5.of the Service Manual
F7-02
28 OPC Drum
60K 60K
F7-10 F7-06
44
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
No.
Mechanical Parts
29 Charge Corona Case 30 Charge Wire 31 32 33 34 35 Cleaning Blade Front Cleaning Felt Rear Cleaning Felt Cleaning Sponge Splash Prevention Sheet Fuser Unit
Replacement/Adjustment Ref. Cycle Counter Procedure (Sheet) Refer to F7-07 2.2.5.of the 60K Service Manual 60K 60K 60K 60K 60K
36 Fuser Roller 37 Pressure Roller 38 Fuser Roller Bushing 39 Pressure Roller Bushing 40 Thermistor Assembly 41 Fuser Lamp 42 Separator 43 Exit 2 Roller Main Unit 44 Ozone Filter 45 Toner Spill Tray
1115 1021 1114 1020 1125 1116 1109 1104 825 1202
F7-02
Note: 1. Wet Cloth represents a soft cloth saturated with water. For stubborn toner accumulation, wipe with a soft cloth saturated with Isopropyl Alcohol first, then follow up with a soft cloth saturated with water. 2. The Maintenance Cycle is based on the Counter Information for each individual module. To verify the counter information, print the Total Counter List using the Service Mode: F7 - Electronic Counter - 00 (List Print). 3. Cleaning, Replacement, and Adjustment Cycle (Sheet) are based on using Panasonic's recommended standard paper, and supplies. These cycles may vary with the kind of paper used, Paper size, orientation, print duty, continuous/interval print, and/or ambient conditions. Total Counter View Mode on the LCD The Total Counter can be displayed on the Panel Display by pressing "COPY SIZE", and "PAPER TRAY" keys simultaneously in Standby mode for quick reference.
DP-8020E/8020P/8016P
2.5.
When the machine reaches the preset P/M Cycle, it will show "Call for P/M", or "Replace The Toner Waste Container" on the LCD Display. The PM Counter can be reset by following the procedures below.
2.5.1.
1. Perform the P/M (Preventive Maintenance). Refer to Section 2.3, and 2.4. 2. Press FUNCTION, ORIGINAL SIZE, and 3 keys sequentially to enter the Service Mode. 3. Enter the Copy Service Mode F5-70 (PM Cycle), and change to the desired value. 4. Press FUNCTION, and CLEAR keys simultaneously to exit the Service Mode.
2.5.2.
1. Perform the P/M (Preventive Maintenance). Refer to Section 2.3, and 2.4. 2. Press FUNCTION, ORIGINAL SIZE, and 3 keys sequentially to enter the Service Mode. 3. Enter the Copy Service Mode F5-87 (ADF PM Cycle), and change to the desired value. 4. Press FUNCTION, and CLEAR keys simultaneously to exit the Service Mode.
2.5.3.
A. Blinking Maintenance, and Toner Waste Container Indicators Upon detecting that the Toner Waste Container is full, the machine will complete the current job, and stop operating. A blinking Maintenance, and Toner Waste Container Indicators will appear on the display. To continue using the machine temporarily while waiting for the Service Technician, press any key (up to 100 additional copies can be made). B. Steady Maintenance, and Toner Waste Container Indicators Upon reaching the 100 copies, the machine stops, and will not allow further operation until the Toner Waste Container is replaced. Replace the Toner Waste Container. (Refer to Section 2.2.5.of the Service Manual)
46
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.6.
This information is used for routine Preventive Maintenance (PM) calls to ensure the highest degree of reliability. Inspect the following areas, and lubricate as required. The inspection interval is usually 120K copies, or more, however the interval may be reduced due to environmental conditions. Ref. No. Automatic Duplex Unit Mechanical Parts Grease Lubrication Point
712
709
47
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.7.
The Quickest, and Most Easiest Method of Updating the Firmware is to use the Network Firmware Tool (FUP) using Ethernet LAN Port, and a Crossover Cable. The Network FUP Tool version must be 3.XX, or higher, and it can be found on the Panasonic Document Management System CD-ROM included with the main unit, or on the CD-ROM included with the PCL, or PS/PCL options. Refer to the Firmware Update Operation Instructions, Service Notes (8.1.) for additional details.
2.7.1.
Firmware Configuration
A. Hardware Configuration This machine is controlled by two (2) CPUs which are located on the System Control (SC) PC Board, and the Scanner Printer Control (SPC) PC Board.
SC PC Board
On Board PC Ethernet Port PC USB Port Slot 1 FRM PCB 8 MB CPU F-ROM 4 MB
Slot 2
Not Used
B. SC PC Board Firmware The 4 MB Program Memory (F-ROM) is integrated on the SC PCB. An Optional Expansion 8 MB Program Memory (FRM8 PCB) can be installed into SLOT 1. The Firmware to be written into the 4 MB onboard, and the 8 MB of SLOT 1 depends upon the configuration of the Standard, PCL, or PS Options. (1) Standard The Standard Program (1) is only written into the 4 MB onboard, which is assigned as ROM Code (A). (2) For PCL Option The PCL Control Program (2) must be written into the 4 MB onboard, which is assigned as ROM Code (B). The PCL Control Program (3), and PCL Font data (4) are written into the 8 MB in the SLOT 1. The Firmware (3), and (4) are assigned as ROM Code (C). When using 8 MB Flash Memory Card, the 8 MB Program (C) can be written onto one card.
48
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
When using 4 MB Flash Memory Card, the 8 MB program (C) must be divided onto 2 cards, one 4 MB card for the PCL Control Program (3), and one 4 MB card for the PCL Font data (4). (3) For PS Option The PS Control Program must be written into the 4 MB onboard, which is assigned as ROM Code (D). The PS Control Program (6), and (7) are written into the 8 MB in the SLOT 1. Both Firmwares (6), and (7) are assigned as ROM Code (E). When using 4 MB Flash Memory Card, the 8 MB program (E) must be divided onto 2 cards, one 4 MB card for the PS Control Program (6), and one 4 MB card for the PS Control Program (7). C. SPC PC Board Firmware The 512 KB Program Memory (F-ROM) is integrated on the SPC PCB. The Programs for Scanner Control, and Printer Control are saved on the Board. The Firmware is transferred as Serial Data from the SC PCB. D. Firmware Updating Ports Three (3) types of Ports are available for updating the firmware. (1) Ethernet LAN Port (The Quickest, and Most Easiest Method) The machine's Firmware can be updated from a PC via Local Area Network (LAN). Refer to the Firmware Update Operation Instructions, Service Notes (8.1.) for additional details. (2) USB Port (Alternate) The machine's Firmware can be updated from a PC via USB Port. The Master Firmware Card can also be created from a PC using the USB Port. Refer to the Firmware Update Operation Instructions, Service Notes (8.1.) for additional details. (3) Flash Memory Card (Alternate) The machine's Firmware can be updated using the Master Firmware Card. The Master Firmware Card can be created by copying the Firmware from an existing machine's SC PCB using a 4 MB, or 8 MB Flash Memory Card. To update the SC, SPC, and PNL PCB, 3 Flash Memory Cards are required for the Standard configuration, or 5 Flash Memory Cards for the PCL, or PS/PCL configuration.
2.7.2.
Updating through a LAN Port (The Quickest, and Most Easiest Method)
The firmware code can be easily updated when the main unit is connected to a LAN. The Network Firmware Update Tool can also be used by connecting to the machine using a crossover cable, if the unit is not connected to a LAN. 1) Install the Network Firmware Update Tool to your PC The option CD-ROM includes the Network Firmware Update Tool, and the Main Unit Firmware Code. Please refer to the following Operating Instructions to install the Network Firmware Update Tool. The installation password is "workio". Operating Instructions: \xFirmware\Tools\NwFirmup\NwFirmup OI.pdf (Refer to the NW Firmware Update Tool OI on the CD) Setup: \xFirmware\Tools\NwFirmup\Setup\Setup.exe 2) Preparing the Firmware Code Double click the appropriate Destination Shortcut Batch File, and copy the Firmware Code File on the CD-ROM to the Firmware Data Folder in your PC. Note that the files in the Archive will be extracted automatically into the designated folder when the Archived file (.exe) is Double-clicked.
49
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Example: From: Destination Shortcut Batch File: D:(CD-ROM Drive) \ xFirmware \ USA.bat Firmware Code File: DP-8016_8020_PU_xxxxxx.exe To: Firmware Data Folder: C:\ Panasonic \ Panasonic-FUP \ Data 3) Preparing the Main Unit for the Firmware Upgrade Make sure the unit's Key Operator Password is the same as the tool's password. Make sure the unit is in an idle state (e.g. not making copies, not printing, etc.). 4) Upgrading the Main Unit's Firmware Code Start the Network Firmware Update Tool, and select the following Firmware Code Folders in the C:\Panasonic\Panasonic-FUP\Data folder, and then follow the display instructions to upgrade the Main Unit's Firmware Codes.
Parent Firmware File Folder \ DP-8016_8020_PU_xxxxxx Sub Firmware File Folder Transferring Order 1 1 1 2
When you select the Parent Folder, the following Firmware Type window appears. Proper Sub File Folders are selected automatically by selecting the Firmware Type. The transferring order is set up automatically.
Note: 1. Manual mode must be used, when updating the designated version of the firmware, or changing the type of the firmware. Please refer to the Section 2.2, "Setting up the Network Firmware Update Tool, File Selection Tab" of the Operating Instructions. 2. While updating the firmware code, the display may become garbled, however, it will return to normal upon completion of the firmware update. 3. If the firmware update fails, and the unit does not boot up, the Network Firmware Update Tool will not be able to transfer the firmware code. If this occurs, please refer to the next section "Updating through the USB Port", and use the Local Firmware Update Tool to recover the unit. 4. The suffix "_xx" for the Folder Name, or File Name may not exist depending on the destination location.
2.7.3.
If the device is not connected to the LAN, upgrade the firmware code using the USB Port. 1) Install the Local Firmware Update Tool to your PC The option CD-ROM includes the Local Firmware Update Tool, and the Main Unit Firmware Code. Please refer to the following Operating Instructions to install the Local Firmware Update Tool. Operating Instructions: \xFirmware\Tools\Firmup\FIRMUP OI.pdf (Refer to the Local Firmware Update Tool OI on the CD) Setup: \xFirmware\Tools\Firmup\Setup\Setup.exe 50
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2) Preparing the Firmware Code Double click the appropriate Destination Shortcut Batch File, and copy the Firmware Code File on the CD-ROM to the Firmware Data Folder in your PC. Note that the files in the Archive will be extracted automatically into the designated folder when the Archived file (.exe) is Double-clicked. Example: From: Destination Shortcut Batch File: D:(CD-ROM Drive) \ xFirmware \ USA.bat Firmware Code File: DP-8016_8020_PU_xxxxxx.exe To: Firmware Data Folder: C:\ Panasonic \ Panasonic-FUP \ Data 3) Preparing the Main Unit for the Firmware Upgrade Important: DO NOT connect the USB Cable yet. Enter into Test Mode F9-07-01 to enable the unit to accept the programming code from the USB Port. Now connect the USB Cable between the Unit, and PC. 4) Upgrading the Main Unit's Firmware Code Start the Local Firmware Update Tool, and select the following Firmware Code Parent File Folder in the C:\Panasonic\Panasonic-FUP\Data folder, and select the Firmware Code Type then follow the display instructions to upgrade the Main Unit's Firmware Codes. You must process each firmware file separately in this manner, and sequence.
Parent Firmware File Folder \ DP-8016_8020_PU_xxxxxx Sub Firmware File Folder Firmware File Transferring Order 1 1-1 1-2 1-3 1-1 1-2 1-3 2
\ SC_STD \ DP-LL80AxVxxxxx_xx DP-LL80AxVxxxxx_xx.bin \ SC_PCL \ DP-LL80BxVxxxxx_xx DP-LL80BxVxxxxx_xx.bin \ SC_PS \ DP-LL80DxVxxxxx_xx \ SPC \ LL80-SPCAxVxxxxxx
DP-LL80CxVxxxxxa_xx.bin DP-LL80CxVxxxxxb.bin DP-LL80DxVxxxxx_xx.bin DP-LL80ExVxxxxxa_xx.bin DP-LL80ExVxxxxxb.bin LL80-SPCAxVxxxxxx.bin
When you select the Parent Folder, the following Firmware Type window appears. Proper Firmware Files are selected automatically by selecting the Firmware Type. The transferring order is set up automatically.
Note: 1. While updating the firmware code, the display may become garbled, however, it will return to normal upon completion of the firmware update. 2. Please refer to the service manual for additional details. 3. The suffix "_xx" for the Folder Name, or File Name may not exist depending on the destination location.
51
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.7.4.
Updating the Firmware using the Master Firmware Card (Alternate method)
1. Before starting, print the F5/F6 Parameters List (Copy Service Mode F9-03-00). 2. Turn the Power Switch on the Right side of the machine to the OFF position. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord, if the Fax Option is installed.) 3. Install the appropriate Master Firmware Card into the machine. 4. Turn the Power Switch on the Right Side of the machine to the ON position. 5. Press FUNCTION, ORIGINAL SIZE keys, and then Key 3 on the keypad sequentially. 6. Perform the Copy Service Mode F9-07-00 (Update From Master Card). 7. The firmware is copied into the machine. 8. After the update is completed, the machine reboots itself, and returns to standby. 9. Turn the Power Switch on the Right side of the machine to the OFF position. 10. Remove the Master Firmware Card from the machine. 11. Turn the Power Switch on the Right Side of the machine to the ON position. 12. Reprogram the F5 & F6 Parameters according to the lists printed in Step 1 above if the settings are other than factory default. Note: After the update is completed, the machine reboots itself, and returns to standby mode. Repeat the above steps if there are additional firmware code files to be updated. Confirm that the update was successfully completed by checking the Firmware Version with F9 Parameters F9-02-xx. Caution: If the unit does not boot up properly in step 8, refer to Service Manual 3.7.8. (Firmware Emergency Recovery) 3.7.4.1. Creating a Master Firmware Card A. Utilizing the Firmware Update Kit 1) Install the Local Firmware Update Tool to your PC The option CD-ROM includes the Local Firmware Update Tool, and the Main Unit Firmware Code. Please refer to the following Operating Instructions to install the Local Firmware Update Tool. Operating Instructions: \xFirmware\Tools\Firmup\FIRMUP OI.pdf (Refer to the Local Firmware Update Tool OI on the CD) Setup: \xFirmware\Tools\Firmup\Setup\Setup.exe 2) Preparing the Firmware Code Double click the appropriate Destination Shortcut Batch File, and copy the Firmware Code File on the CD-ROM to the Firmware Data Folder in your PC. Note that the files in the Archive will be extracted automatically into the designated folder when the Archived file (.exe) is Double-clicked. Example: From: Destination Shortcut Batch File: D:(CD-ROM Drive) \ xFirmware \ USA.bat Firmware Code File: DP-8016_8020_PU_xxxxxx.exe To: Firmware Data Folder: C:\ Panasonic \ Panasonic-FUP \ Data 3) Preparing the Main Unit for the Programming Master Firmware Card Important: DO NOT connect the USB Cable yet. 1. Turn the Power Switch on the Right side of the machine to the OFF position. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord, if the Fax Option is installed.) 2. Insert/Remove the Flash Memory Card (4 MB, or 8 MB) into/from the machine. 52
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
3. Turn the Power Switch on the Right Side of the machine to the ON position. 4. Press FUNCTION, ORIGINAL SIZE keys, and then Key 3 on the keypad sequentially. 5. Perform the Update Program Card Mode F9-09 (Update Program Card). The unit is now ready to accept the firmware code from the USB Port. Now connect the USB Cable between the Unit, and PC. (Refer to the Local Firmware Update Tool OI on the CD) Repeat the above steps if there are additional master firmware cards to be programmed. B. Copying the Firmware from an Existing Machine using a Flash Memory Card (4 MB, or 8 MB) 1. Turn the Power Switch on the Right side of the machine to the OFF position. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord, if the Fax Option is installed.) 2. Install a Flash Memory Card (4 MB, or 8 MB) into the machine. 3. Turn the Power Switch on the Right Side of the machine to the ON position. 4. Press FUNCTION, ORIGINAL SIZE keys, and then Key 3 on the keypad sequentially. 5. Perform the Copy Service Mode F9-08 (Program Backup). 6. The firmware is copied into the Flash Memory Card. 7. After the backup is completed, press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby. 8. Turn the Power Switch on the Right side of the machine to the OFF position. 9. Remove the Master Firmware Card that you just created from the machine. 10. Turn the Power Switch on the Right Side of the machine to the ON position. 11. Use this Master Firmware Card to update the firmware on other machines. 3.7.4.2. Erasing the Master Firmware Card 1. Turn the Power Switch on the Right side of the machine to the OFF position. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord, if the Fax Option is installed.) 2. Install the Master Firmware Card into the machine. 3. Turn the Power Switch on the Right Side of the machine to the ON position. 4. Press FUNCTION, ORIGINAL SIZE keys, and then Key 3 on the keypad sequentially. 5. Perform the Service Mode F9-09 (Update Program Card). 6. After the Flash Memory Card is erased, machine prompts READY TO PROGRAM PRESS SET TO START. Press STOP. 7. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby. 8. Turn the Power Switch on the Right side of the machine to the OFF position. 9. Remove the blank Flash Memory Card from the machine. 10. Repeat from Step 2 above if you are erasing another Master Firmware Card.
53
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.7.5.
If your customer requires User Authentication, and/or Via Fax Server, setup the feature(s) by referring to the Operating Instructions (For User Authentication).
2.7.6.
After the Hard Disk Drive Unit is installed, to prevent a Scan Disk Function from being performed (similar to Windows OS when the power is abruptly interrupted), it is important to follow the step sequence below when turning OFF the Power Switch on the machine. 1. If the machine is in the "ENERGY SAVER (Shutdown Mode)", you may turn the Power Switch on the Right Side of the machine to the OFF position. If it is not in the "ENERGY SAVER (Shutdown Mode)", continue to step 2 below. 2. Press "FUNCTION", and "ENERGY SAVER" keys simultaneously first. 3. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk Drive Unit, and advances into ENERGY SAVER MODE. 4. Turn the Power Switch on the Right side of the machine to the OFF position. 5. Unplug the AC Power Cord. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord, if the Fax option installed.) 6. After finishing the installation of the Hard Disk Drive, please go over the above Power Down procedure with the customer to avoid the Scan Disk Function from being performed (indicated by SCANNING HARD DISK message on the display), and customer inquiries related to abrupt Power Off. 7. Reconnect the Telephone Line Cable if it was disconnected.
2.7.7.
The easiest method to recover the firmware in an Emergency Recovery routine is to either use the Local Firmware Update Tool software by selecting the Independent File method, or using the Master Firmware Flash Card method (2 Flash Cards required). Whichever method you select, it is easier to restore the machine's firmware to the Standard (AAV) Type first as it only requires 2 files to bring the machine to initial working condition. (Install the files in this order: SC, and SPC). After recovering, if optional PCL, or PS/PCL firmware is required, use the Network Firmware Update Tool, or the Local Firmware Update Tool to update the firmware to the required level. If the unit does not boot up properly, follow the steps below: 1. Turn the power Off (use the power switch on the right side of the unit). - Before proceeding to the next step, you must prepare either the Local Firmware Update Tool, or create the Master Firmware Flash Cards (read the appropriate sections first). - If using the Master Firmware Card, insert the Master Firmware Flash Cards in the unit. 2. Turn the power On while holding the ENERGY SAVER key. 3. When the green lamp on the front panel turns On, release the ENERGY SAVER key. - If using the Master Firmware Card, the unit will start updating the Firmware code files automatically. The unit is now ready to accept the firmware code from the USB Port, or Master Firmware Card. Repeat the above steps if there are additional firmware code files to be updated.
54
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.7.8.
Firmware Version
SC :
DP-LL80 A A Vxxxxx (a) PU (AU) Destination Code (Fax) AU : USA/Canada AB : UK Destination Code (Copier) PU : USA/Canada PB : UK Division Soft (When it is divided into (a) and (b)) Firmware Version (V1xxxx) Language Code A : A-English, C-French & Spanish c : French, German, Italian, Dutch, Portuguese, Spanish, English & Greek d : French, German, Swedish, Norwegian, Danish, Finnish, Turkish & English e : French, German, English, Polish, Hungarian, Czech & Russian j : English & Korean k : English & Taiwanese n : English & Chinese Firmware Type A : Standard B, C, D, E : Optional Model Number
SPC
LL80- SPC
Model Number
55
Ver. 1.0 OCT 2006
2.8.
Ver. 1.0
When the following items are replaced or cleaned, perform adjustments in the correct order.
No.
Work
Part Item 1 1 1 1 1 2
Remark
56
1 2 3 4 2 1 2 1 1 2 3 3 1
1 2 3 4 5 6 7 8 5 3 4 2 4 1 6 4 5 3 5 2
Installation Main Cleaning Optics Process Unit Toner Spill Tray Replace Scanning Lamp Platen Glass OPC Drum Developer
LSU Image PWM OPC Print LSU PWM Density TDC Adj. Counter Pattern F5/F6 Adj. F6-49 Adj. Adj. F6-39 (Note 4) (Note 1) Reset Print /50/51 F8-09 (Note 3) F8-14 F8-18 (Note 2) 4 3 1 2 3 2 3 2 2 3 2 2 1 5 4 3 2 3 1
10 11
12
Replace Developer
13 14
LSU SC PC Board
DP-8020E/8020P/8016P
OCT 2006
DP-8020E/8020P/8016P
Note: 1. Print F5/F6 1) Press FUNCTION, ORIGINAL SIZE, and 3 keys sequentially to enter the Service Mode. 2) Press the "9" key to enter the F9 Mode (Unit Maintenance). 3) Press the "START" key. 4) Press "3", and "SET" keys. 5) Press "V", or "/\" arrow keys to select "00 F5/F6 PARAMETERS", and press "SET" key. 6) Prints the memory contents of the F5, and F6 modes. 2. Contrast Adjusting 1) Press FUNCTION, ORIGINAL SIZE, and 3 keys sequentially to enter the Service Mode. 2) Press the "2", and the "START" keys to enter the F2 Mode (Single Copy Test). 3) Set the exposure to the center position. 4) Set the machine to TEXT / PHOTO Mode. 5) Make a copy of Test Chart 53/54 with gray scale (P/N: FQ-SJ1011), and compare the density to the chart shown below. If it is within specification, skip to step (14). a. Gray scale A should not be visible. b. Gray scale 2 should be clearly visible.
A
. . . . . . . . . . .. . . . . . 1 . . .
2 3
6) Press the "STOP" key to exit the F2 Mode (Single Copy Test). 7) Press the 6, and the "START" keys to enter the F6 Mode (Adjust Parameters). 8) Enter F6-50 Mode (T/P Mode Image Density). 9) Press the "SET" key to highlight the current value. 10) Enter a new value (up to 3-digits). Note: The RESET key is used to change to a Negative, or Positive (+/-) value. (+) : Lighter (-) : Darker 11) Press the SET, and STOP keys. 12) Enter F2 Mode (Single Copy Test). 13) Make a copy to confirm the adjustment. Note: Repeat Steps (3) to (10) until desired density is attained. F6-49 : T Mode Image Density (Text) F6-51 : P Mode Image Density (Photo) 14) Press FUNCTION, and CLEAR keys simultaneously to exit the Service Mode.
57
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
3. PWM Adjustment 1) Ensure that Ledger / A3 Size Paper is loaded in one of the Trays, and pull out the remaining trays (including the bypass tray) to disable them. 2) Press FUNCTION, ORIGINAL SIZE, and 3 keys sequentially to enter the Service Mode. 3) Press the "8" key to enter the F8 Mode (Service Adjustment). 4) Press the "START" key. 5) Press the "1", "8", and "SET" keys sequentially to enter the F8-18 "C18 PRT PWM ADJ. PTN.". 6) Press the "START" key to begin the LSU PWM Pattern Printing. Sample: 4 gray patches are visible in the illustration, the value of the uppermost patch position is "+2" in our example.
(-5)
(0) +2
(+5)
7) Press the "STOP" key. 8) Press the "6", and the "START" keys to enter the F6 Mode (Adjust Parameters). 9) Select "39 LSU Unit PWM ADJUST". 10) Press "SET" button, and enter the value of the gray patch, as established in Step (6). 4. LSU Adjustment Refer to 2.9.
58
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.9.
When installing the Paper Tray option, the following LSU Image Side to Side adjustment must be performed. The Printer registration is adjusted at the factory. If copy image is abnormal, specially in the Rotation Copy mode, adjust it by the following procedure.
2.9.1.
Printer Registration
1. Insert Ledger, or A3 size paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 2. Press FUNCTION, ORIGINAL SIZE keys, and then Key 3 on the keypad sequentially. 3. Perform the Service Mode F1-03 (Print Test Pattern 1). 4. Check the gap of the print pattern from the paper edge, refer to the Figure below. 5. Perform the Service Mode F6-04 (Printer Registration) to adjust the gap to be 5 mm. 6. If the gap is less than 5 mm, input a (-) value. If more than 5 mm, input a (+) value. 7. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby.
<Figure> Two lines are printed on the top (Lead edge). For Ledger or A3, place as Portrait. For Letter or A4, place as Landscape. 5 mm Top (Lead edge) Two lines are printed
5 mm
5 mm
2.9.2.
1. Insert paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 2. Press FUNCTION, ORIGINAL SIZE keys, and then Key 3 on the keypad sequentially. 3. Perform the Service Mode F1-03 (Print Test Pattern 1). 4. Check the gap of the print pattern from the paper edge, refer to the Figure above. 5. Perform the Service Mode F6-10 to F6-14, to adjust the gap to be 5 mm. 6. If the gap is less than 5 mm, input a (+) value. If more than 5 mm, input a (-) value. 7. Proceed the above steps for other Tray. 8. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby.
59
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.9.3.
1. Insert paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 2. Press FUNCTION, ORIGINAL SIZE keys, and then Key 3 on the keypad sequentially. 3. Perform the Service Mode F1-06 (Print Test Pattern 4). 4. Check the gap of the print pattern from the paper edge, refer to the Figure above. 5. Perform the Service Mode F6-16 (ADU Side Adjust), to adjust the gap to be 5 mm. 6. If the gap is less than 5 mm, input a (+) value. If more than 5 mm, input a (-) value. 7. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby.
2.9.4.
1. Place the Original Document on the Platen Scanner. 2. Insert Ledger, or A3 size paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 3. Press FUNCTION, ORIGINAL SIZE keys, and then Key 3 on the keypad sequentially. 4. Perform the Service Mode F2 (Single Copy Test). 5. Check the Image size of the Copy, and the Original as Portrait. 6. Perform the Service Mode F6-00 (Adj 100% Side-Side Read), to adjust for an identical vertical (side-to-side) size ratio. 7. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value. 8. Perform the Service Mode F6-01 (Adj 100% Lead-Tail Read), to adjust for an identical horizontal (top-to-bottom) size ratio. 9. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value. 10. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby. Note: This is for size adjustment, and does not adjust positioning.
2.9.5.
1. Place the Original Document on the Platen Scanner. 2. Insert Ledger, or A3 size paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 3. Press FUNCTION, ORIGINAL SIZE keys, and then Key 3 on the keypad sequentially. 4. Perform the Service Mode F2 (Single Copy Test). 5. Check the Image size of the Copy, and the Original as Portrait. 6. Perform the Service Mode F6-03 (Original Registration), to adjust the platen original registration detection timing. 7. If the gap is smaller than the Original, input a (-) value. If bigger than the Original, input a (+) value. 8. Perform the Service Mode F6-53 (CCD Read Position Adj), to adjust the CCD Read side position. 9. If the gap is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value. 10. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby.
60
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.9.6.
1. Place the Original Document on the ADF. 2. Insert Ledger, or A3 size paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 3. Press FUNCTION, ORIGINAL SIZE keys, and then Key 3 on the keypad sequentially. 4. Perform the Service Mode F2 (Single Copy Test). 5. Check the Image size of the Copy, and the Original as Portrait. 6. Perform the Service Mode F6-93 (ADF 100% Image 1-Sided), to adjust for an identical vertical (side-to-side) magnification for 1-sided scan. 7. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value. 8. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby. Note: This is for size adjustment, and does not adjust positioning.
2.9.7.
1. Place the Original Document on the ADF. 2. Insert Ledger, or A3 size paper into the 1st tray, and change the tray setting to the appropriate paper size. Empty, or pull out all the remaining trays (including the bypass tray) to disable them. 3. Press FUNCTION, ORIGINAL SIZE keys, and then Key 3 on the keypad sequentially. 4. Perform the Service Mode F2 (Single Copy Test). 5. Check the Image size of the Copy, and the Original as Portrait. 6. Perform the Service Mode F6-91 (Original Read Edge ADF), to adjust for the ADF Original Read Edge detection timing. 7. If the gap is less than the Original, input a (+) value. If bigger than the Original, input a (-) value. 8. Perform the Service Mode F6-90 (ADF Read Main Scan Pos.), to adjust for the ADF horizontal image read start position. 9. If the gap is less than the Original, input a (+) value. If bigger than the Original, input a (-) value. 10. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby.
61
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.9.8.
Caution: Confirm that the Scanning Pad is installed, and aligned correctly on the ADF/i-ADF prior to making any adjustments. (Refer to the ADF/i-ADF Installation Instructions in Sect. 8.11., or 8.12.of the Service Manual) 1. Place a Business Card, Driver's License, Insurance Card, etc. (Invoice size, or smaller) on the Platen Glass as illustrated.
Driver's License
Platen
2. Insert Letter, or A4 size paper into the 1st Paper Tray, or onto the Sheet Bypass, and change the tray settings to the appropriate paper size. 3. Make a copy using the Double Exposure Copy Mode. 4. Check the Copy Image. a. For a Horizontal Black Line in the Center, adjust the Service Mode F6-63 (Lead Edge Read Timing) by following the steps below. b. For a Vertical Black Line at the Leading Edge, adjust the Service Mode F6-64 (Side Edge Read Adjust) by following the steps below.
Output of Letter (A4) Paper (not LTR-R) Driver's License Adjust with F6-63 Driver's License
Driver's License
Driver's License
5. Press FUNCTION, ORIGINAL SIZE keys, and then Key 3 on the keypad sequentially. 6. Perform the Service Mode F6-63 (Lead Edge Read Timing), and F6-64 (Side Edge Read Adjust). Note: It is not recommended setting the value higher than "4" as it will increase the Void Area. 7. Press "STOP" first, and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby. 8. Repeat the above steps 3 to 7 until the Black Line(s) disappear.
62
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Signal Name +12V +24V +24VD1 +24VFL +24VM +24VOPC +24VOPF +3.3V +5v +5VD +5VP +ACT +ALM +DAT +SLP AC(L) AC(N) ACSW ADF2 ADF3 ADF4 AGND BAT+ BMCNT BTHP BZBZ+ C1C1+ C2C2+ C3+ C4+ CASET CCRMT CPWM CSB1 CST2 CST3 CST4 CSTOP CSTOP4
63
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Signal Name DAA1 DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DDCPWM E_RDB ELPCNT F/R FDPCHK2 FDPCHK3 FDPCHK4 FSH GND GPWM HFSOL HPMB HSYNC HUMISN HVAC1 HVAC2 IICSCL IICSDA IOUTA IOUTB JAMDOR2 JAMDOR3 JAMDOR4 KCDET KCNT KIN0 KIN1 KIN2 KIN3 KIN4 KIN5 KIN6 KIN7 L1 L2 L5V LD
Glossary of Electrical Abbreviations Function ADF Motor Current Control Signal Data Signal Data Signal Data Signal Data Signal Data Signal Data Signal Data Signal Data Signal Development Control DC ON/OFF PWM Read/Write Execution Control Signal Discharge Lamp Direction of Rotation Signal 2nd Paper Tray Paper Registration Detection Signal 3rd Paper Tray Paper Registration Detection Signal 4th Paper Tray Paper Registration Detection Signal Transfer Gate Clock Ground Grid Control ON/OFF PWM Temp Humidity Sensor Signal LCD driver Power Control Signal Horizontal Synchronous Signal Temp Humidity Sensor Signal INV PC Board/Lamp Signal INV PC Board/Lamp Signal IIC Transmission Clock IIC Transmission Signal Motor Control Signal Motor Control Signal 2nd Paper Tray Jam Access Cover Open Detection Signal 3rd Paper Tray Jam Access Cover Open Detection Signal 4th Paper Tray Jam Access Cover Open Detection Signal Key Counter Option Detection Key Counter Option PNL Key Signal (Key Line) PNL Key Signal (Key Line) PNL Key Signal (Key Line) PNL Key Signal (Key Line) PNL Key Signal (Key Line) PNL Key Signal (Key Line) PNL Key Signal (Key Line) PNL Key Signal (Key Line) Line Signal Line Signal Laser Circuit +5VDC Power Supply Motor Lock Detection Signal 64
Ver. 1.0
OCT 2006
DP-8020E/8020P/8016P
Signal Name LDBTHP LDCST2 LDCST3 LDCSTSEN LDDUX LDEN LDFPCHK2 LDFPCHK3 LDFPCHK4 LDHEX LDHFPE LDILDI+ LDJAM2 LDJAM3 LDJAM4 LDORI LDPED LDPHK2 LDPHK3 LDPHK4 LDPSEN LDRRSEN LDSSN LDTF LDUPL2 LDUPL3 LDUPL4 LDUPLSEN LDWTB LED0 LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 LED9 LEDCT0 LEDCT1 LEDCT2 LEDCT3 LEDCT4 LIFT1
Glossary of Electrical Abbreviations Function Toner Bottle HP Sensor Signal Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Laser Control Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Laser Diode Control Laser Diode Control + Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage Photo Sensor DC Drive Voltage PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal PNL LED Control Signal 1st Paper Tray Lift Motor Signal 65
Ver. 1.0
OCT 2006
DP-8020E/8020P/8016P
Signal Name LIFT2 LIFT4 LIFTM2 LIFTM4 MGND MRCLH2 MRCLH3 MRCLH4 N.C. nA3SEN nA5SEN nAA3S nAA3SN nAADL1 nAADL2 nAAPNT nAB1SN nAB2SN nAB4S nAB4SN nACLH1 nACLH2 nACLH3 nACLOCKAD1 nAEJC nAKEEP1 nAKEEP2 nANG nAOAC nAPACHG nAPICR nAREV nASTAMP nASTROAD1 nATT nB4SEN nBDOOR nCCLH1 nCCLH2 nCCLH3 nCST2 nCTCNT nCTON nDADFON nDUPACK nDUPSEN
Glossary of Electrical Abbreviations Function 2nd Paper Tray Lift Motor Signal 4th Paper Tray Lift Motor Signal 2nd Paper Tray Lift Motor Drive Signal 4th Paper Tray Lift Motor Drive Signal Ground 2nd Paper Tray Intermediate Roller Clutch Drive Signal 3rd Paper Tray Intermediate Roller Clutch Drive Signal 4th Paper Tray Intermediate Roller Clutch Drive Signal No Connection Sheet Bypass Paper Size Detection Signal Sheet Bypass Paper Size Detection Signal Original Width Detection Signal Original Width Detection Signal Original Length Detection Signal Original Length Detection Signal Original Detection Signal Read Point Detection Signal Duplex Eject Detection Signal Original Width Detection Signal Original Width Detection Signal Feed 2 Roller Clutch Control Signal Paper Feed Roller Clutch Control Signal Inverting Roller Clutch Control Signal ADF Motor Control Clock Signal Original Eject Detection Signal Reversing 1 Guide Solenoid Control Signal Reversing 1 Guide Solenoid Control Signal Platen Cover Angle ADF Cover Open Detection Signal Release Lever Plate Solenoid Control Signal Release Lever Plate Solenoid Control Signal ADF Exit Cover Open Detection Signal Stamp Control Signal ADF Motor Control Strobe Signal Attention Signal Sheet Bypass B4 Paper Detection Signal Platen Cover Open Detection Signal Feed 2 Roller Clutch Control Signal ADF Roller Clutch Control Signal Inverting Roller Clutch Control Signal 2nd Paper Tray Detection Signal Counter Drive Signal Ring Detection Signal ADF Option Detection Signal Duplex Print Acknowledge Signal ADU Sensor Signal 66
Ver. 1.0
OCT 2006
DP-8020E/8020P/8016P
Signal Name nDUREQ nDUXSOL nFLON nFNRDT nFNRDTP nHEXSEN nHFPESEN nHKOF nLEDACT nLEDALM nLEDDAT nLEDSLP nLIFTM3 nLPOW1 nLPOW2 nMMCK nMMON nMMRDY nOPDUP nOPT nORI nOUTA nOUTB nPACK nPCHK4 nPEDSEN nPHY1 nPHY2 nPHYCP nPHYR nPNLRST nPRDY nPRGDWN nPVSYNC nSACK nSADFON nSCNWUP nSLPKY nSREQ nSTAMP nTFSEN nVCNT nVRDY nWAKE nWTBSEN OP3CLK
Glossary of Electrical Abbreviations Function Duplex Print Request ADU Solenoid Control Signal Inverter Ground Fan Ready Signal PS Fan Ready Signal Paper Exit Sensor Signal Bypass Feed Sensor Signal External Phone Off-Hook Detection Signal ACTIVE Lamp LED Control Signal ALARM Lamp LED Control Signal DATA Lamp LED Control Signal Energy Saver Lamp LED Control Signal 3rd Paper Tray Lift Motor Drive Signal Power Control Power Control Main Motor Clock Main Motor Rotation Control Signal Main Motor Ready Signal Duplex Unit Detection Signal PNL4 Detection Home Position Detection Signal Motor Control Signal Motor Control Signal Printer ACK Signal 4th Paper Tray Paper Detection Signal Sheet Bypass Paper Detection Signal CCD CLOCK CCD CLOCK CCD CLOCK CCD CLOCK Panel Reset Signal Printer Ready Signal F-ROM Rewrite Print Registration Scan ACK Signal ADF Detection Signal Energy Saver Signal Energy Saver Key Signal Scanner Request Signal Stamp Control Signal Toner Waste Sensor +24 VDC Power Supply Control Signal VSYNC Reset Signal FAX Wake Up Signal Toner Waste Container Detection Sensor Signal 3rd Paper Tray Motor Clock 67
Ver. 1.0
OCT 2006
DP-8020E/8020P/8016P
Signal Name OP3ENB OP3FCK OP3FDIN OP3FLD OP3FLT OP3FOT OP3RST OUTA OUTB P/S pADATA1A pADATA1B pBDA PCHK1 PCHK2 PCHK3 PCHK4 pCMLD PFCLCNT PMCK PMON PMRDY PNLRXD PNLTXD POWCNTV pPHY1 pPHY2 pPHYCP pPHYR PS pSENTIM pSPCRST pSPKOT pVREQ RESETB RETRACE RRCLCNT RS RSEN RW_WRB S/H SCN0 SCN1 SCN10 SCN11 SCN2
Glossary of Electrical Abbreviations Function Option Feed FIFO Enable Option Feed FIFO Clock Option Feed FIFO Input Option Feed FIFO Load Option Feed FIFO Latch Option Feed FIFO Output Option Feed FIFO Reset Motor Control Signal Motor Control Signal Motor Start/Stop ADF Motor Control Signal ADF Motor Control Signal Print BDA Signal 1st Paper Tray Paper Detection Signal 2nd Paper Tray Paper Detection Signal 3rd Paper Tray Paper Detection Signal 4th Paper Tray Paper Detection Signal Line Switching Relay Drive Signal Paper Feed Clutch Drive Signal Polygon Motor Clock Polygon Motor Rotation Signal Polygon Motor Ready Signal PNL Reception Data Signal PNL Transmission Data Signal Laser Power Control Signal CCD CLOCK CCD CLOCK CCD CLOCK CCD CLOCK Parallel / Serial Data Input Select Signal Scanner LSYNC Signal SPC Reset Signal Line Dial Tone Signal Print ACK Request Signal LCD Driver Reset Signal Laser Control Registration Roller Drive Signal Register Selection Control Signal Registration Sensor Signal LCD Control Signal Sample Hold Signal PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) 68
Ver. 1.0
OCT 2006
DP-8020E/8020P/8016P
Signal Name SCN3 SCN4 SCN5 SCN6 SCN8 SCN9 SMCNT SPCRXD SPCTXD SSR TC TDREF TDSEN TEMPSN THERM1 THERM2 TPWM UPLIMIT UPLIMIT2 UPLIMIT3 UPLIMIT4 UPLMT2 UPLMT4 V0 V1 V2 V3 V4 VCL VDD VOUT VOUT1 VOUT2 VSS ZCRS
Glossary of Electrical Abbreviations Function PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) PNL Key Signal (Scan Line) Toner Motor Control Signal SPC Reception Data Signal SPC Transmission Data Signal Heater Control Signal Transfer Control Cleaning Output Toner Density Reference Sensor Toner Density Sensor Signal Temp Humidity Sensor Signal Thermistor Output Signal Ground Transfer Control Transfer Output 1st Paper Tray Paper Level Signal 2nd Paper Tray Paper Level Signal 3rd Paper Tray Paper Level Signal 4th Paper Tray Paper Level Signal 2nd Paper Tray Paper Level Signal 4th Paper Tray Paper Level Signal LCD Driver Supply Voltages LCD Driver Supply Voltages LCD Driver Supply Voltages LCD Driver Supply Voltages LCD Driver Supply Voltages LCD Power Supply +3.3 VDC Power Supply Voltage Converter Input / Output Graphic Data Output Graphic Data Output Ground Heater Control Signal
69
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.10.2. SC PC Board
CN51 SC PCB Pin No. CN51-1 Signal Name +24V Destination PS PCB CN11-1 Signal Waveform Function +24 VDC Power Supply
+24V
CN51-2
GND
PS PCB CN11-2
Ground
0V
CN51-3 +5VP PS PCB CN11-3
+5V
CN51-4
+5VD
PS PCB CN11-4
+5V
CN51-5
+5v
PS PCB CN11-5
+5V
CN51-6
GND
PS PCB CN11-6
Ground
0V
CN51-7 GND PS PCB CN11-7 Ground
0V
CN51-8 GND PS PCB CN11-8 Ground
0V
CN51-9 GND PS PCB CN11-9 Ground
0V
CN51-10 GND PS PCB CN11-10 Ground
0V
CN51-11 +3.3V PS PCB CN11-11
+3.3V
CN51-12
+3.3V
PS PCB CN11-12
+3.3V
70
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Signal Waveform
+24V 0V
CN51-14
nLPOW2
PS PCB CN11-14
+3.3V 0V
Power Control
CN51-15
nVCNT
PS PCB CN11-15
+24V 0V
CN52 SC PCB Pin No. CN52-1 Signal Name +24V Destination PNL1 PCB CN220-1 Signal Waveform Function +24 VDC Power Supply
+24V
CN52-2
GND
Ground
0V
CN52-3 GND PNL1 PCB CN220-3 Ground
0V
CN52-4 GND PNL1 PCB CN220-4 Ground
0V
CN52-5 +5VP PNL1 PCB CN220-5
+5V
CN52-6
+5v
+5V
CN52-7
PNLRXD
+5V 0V
CN52-8
PNLTXD
+5V 0V
71
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Signal Waveform
CN52-10
nLPOW2
Power Control
CN52-11
nLPOW1
+24V 0V
Power Control
CN52-12
nSLPKY
+3.3V PRESSED 0V
CN52-13
nWAKE
+3.3V 0V
CN52-16
nVCNT
+24V 0V
CN53 SC PCB Pin No. CN53-1 Signal Name nPRDY Destination SPC PCB CN717-1 Signal Waveform Function
CN53-2
nVRDY
CN53-3
nPACK
+5V 0V
CN53-4
nATT
+5V 0V
Attention Signal
72
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Signal Waveform
Function
+5V 0V
CN53-6
pBDA
+3.3V 0V
CN53-7
pVREQ
+5V 0V
CN53-8
nSACK
+5V 0V
CN53-9
nPVSYNC
+5V 0V
Print Registration
CN53-10
nDUREQ
+5V 0V
CN53-11
pSENTIM
+5V 0V
CN53-12
nSREQ
+5V 0V
CN53-13
pSPCRST
+5V 0V
CN53-14
nPRGDWN
+5V 0V
F-ROM Rewrite
CN53-15
GND
Ground
0V
CN53-16 GND SPC PCB CN717-16 Ground
0V
73
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Signal Waveform
+5V 0V
CN53-18
IICSDA
+5V 0V
CN53-19
GND
Ground
0V
CN53-20 nSCNWUP SPC PCB CN717-20
+5V 0V
CN53-21
SPCRXD
+5V 0V
CN53-22
SPCTXD
+5V 0V
CN55 SC PCB Pin No. CN55-1 Signal Name VOUT2 Destination CCD CN850-1 Signal Waveform Function Graphic Data Output
4 6V 1V
0V
CN55-2 AGND CCD CN850-2 Ground
0V
CN55-3 VOUT1 CCD CN850-3
4 6V 1V
0V
CN55-4 AGND CCD CN850-4 Ground
0V
CN55-5 AGND CCD CN850-5 Ground
0V
74
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Function
0V
CN55-7 +12V CCD CN850-7
+12V
CN55-8
AGND
CCD CN850-8
Ground
0V
CN55-9 GND CCD CN850-9 Ground
0V
CN55-10 GND CCD CN850-10 Ground
0V
CN55-11 pPHYCP CCD CN850-11
+3.3V 0V
CCD CLOCK
CN55-12
nPHYCP
CCD CN850-12
+3.3V 0V
CCD CLOCK
CN55-13
pPHYR
CCD CN850-13
+3.3V 0V
CCD CLOCK
CN55-14
nPHYR
CCD CN850-14
+3.3V 0V
CCD CLOCK
CN55-15
pPHY2
CCD CN850-15
+3.3V 0V
CCD CLOCK
CN55-16
nPHY2
CCD CN850-16
+3.3V 0V
CCD CLOCK
CN55-17
pPHY1
CCD CN850-17
+3.3V 0V
75
CCD CLOCK
Ver. 1.0
OCT 2006
DP-8020E/8020P/8016P
Signal Waveform
+3.3V 0V
CN55-19
FSH
CCD CN850-19
+3.3V 0V
CN55-20
+5v
CCD CN850-20
+5V
CN57 SC PCB Pin No. CN57-1 Signal Name +3.3V Destination LSU CN2-1 Signal Waveform Function +3.3 VDC Power Supply
+3.3V
CN57-2
GND
LSU CN2-2
Ground
0V
CN57-3 LDI+ LSU CN2-3
+3.3V 0V
CN57-4
LDI-
LSU CN2-4
+3.3V 0V
76
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
+5V
CN650-2
MGND
Ground
0V
CN650-3 GND ADF PCB CN21-3 Ground
0V
CN650-4 +24V ADF PCB CN21-4
+24V
CN650-5
nAAPNT
+5V DETECT 0V
CN650-6
N.C.
No Connection
CN650-7
nAB4SN
+5V 0V
CN650-8
nAA3SN
+5V 0V
CN650-9
nAADL1
+5V 0V
CN650-10 nAADL2
+5V 0V
CN650-11 nAB2SN
+5V 0V
77
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN650-12 nAB1SN ADF PCB CN21-12
Signal Waveform
+5V 0V
CN650-13 nAEJC
+5V 0V
CN650-14 nAREV
+5V OPEN 0V
CN650-15 nAOAC
+5V OPEN 0V
CN650-16 nAKEEP1
+5V 0V
CN650-17 nAKEEP2
+5V 0V
CN650-18 nAPACHG
+5V 0V
CN650-19 nAPICR
+5V 0V
CN650-20 nSTAMP
+5V 0V
CN650-21 nACLH1
+5V 0V
CN650-22 nACLH2
+5V 0V
78
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN650-23 nACLH3 ADF PCB CN21-23
Signal Waveform
+5V 0V
CN650-24 nACLOCKA D1
0V
CN650-25 nASTROAD1 ADF PCB CN21-25
+5V 0V
CN650-26 pADATA1A
+5V 0V
CN650-27 pADATA1B
+5V 0V
CN650-28 +24V
+24V
CN650-29 GND
Ground
0V
CN650-30 +24V ADF PCB CN21-30
+24V
CN650-31 GND
Ground
0V
CN650-32 DAA1 ADF PCB CN21-32
+5V 0V
CN650-33 MGND
Ground
0V
CN650-34 MGND ADF PCB CN21-34 Ground
0V
79
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN650-35 nSADFON ADF PCB CN21-35
Signal Waveform
CN650-36 nDADFON
+5V 0V
CN650-37 +24V
+24V
CN650-38 MGND
Ground
0V
CN650-39 +5v ADF PCB CN21-39
+5V
CN650-40 +5v
+5V
CN655 SPC PCB Signal Name Destination Pin No. CN655-1 OUTA Scanning Motor -1 Signal Waveform Function Motor Control Signal
+18V 0V
CN655-3
nOUTA
Scanning Motor -2
+18V 0V
CN655-2
+24V
Scanning Motor -3
+24V
CN655-4
OUTB
Scanning Motor -4
+18V 0V
CN655-5
+24V
Scanning Motor -5
+24V
80
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN655-6 nOUTB Scanning Motor -6
Signal Waveform
+18V 0V
CN656 SPC PCB Signal Name Destination Pin No. CN656-1 +24V INV PCB CN1-1 Signal Waveform Function +24 VDC Power Supply
+24V
CN656-2
+24V
+24V
CN656-3
nFLON
+24V 0V
Inverter Ground
CN656-4
MGND
Ground
0V
CN656-5 MGND INV PCB CN1-5 Ground
0V
CN657 SPC PCB Signal Name Destination Pin No. CN657-1 +5VP SNS PCB -1 Signal Waveform Function +5 VDC Power Supply
+5V
CN657-2
nANG
SNS PCB -2
+5V ON 0V
CN657-3
GND
SNS PCB -3
Ground
0V
CN657-4 nBDOOR SNS PCB -4
+5V ON 0V
81
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN657-5 nORI Home Position Sensor -1 CN657-6 GND Home Position Sensor -2 Home Position Sensor -3
Signal Waveform
+5V HOME 0V
Ground
0V
Photo Sensor DC Drive Voltage
CN657-7
LDORI
+1.2V
CN701 SPC PCB Signal Name Destination Pin No. CN701-1 L5V LSU CN1-1 Signal Waveform Function Laser Circuit +5VDC Power Supply
+5V
CN701-2
GND
LSU CN1-2
Ground
0V
CN701-3 S/H LSU CN1-3
+5V(H) 0V(L)
CN701-4
HSYNC
LSU CN1-4
+5V 0V
CN701-5
LDEN
LSU CN1-5
+5V(H) 0V(L)
Laser Control
CN701-6
RETRACE
LSU CN1-6
+5V 0V
Laser Control
CN701-7
GND
LSU CN1-7
Ground
0V
CN701-8 POWCNTV LSU CN1-8 Laser Power Control Signal
+1.1V
82
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN701-9 PMCK LSU CN3-1
Signal Waveform
+5V(H) 0V(L)
CN701-10 PMRDY
LSU CN3-2
+5V Ready 0V
CN701-11 PMON
LSU CN3-3
+5V ON 0V
CN701-12 MGND
LSU CN3-4
Ground
0V
CN701-13 +24VM LSU CN3-5
+24V
CN702 SPC PCB Signal Name Destination Pin No. CN702-1 +24VM PS PCB CN500-1 Signal Waveform Function +24 VDC Power Supply
+24V
CN702-2
CPWM
PS PCB CN500-2
0V
CN702-3 GPWM PS PCB CN500-3 Grid Control ON/OFF PWM
+5V 0V
CN702-4
N.C.
PS PCB CN500-4
No Connection
CN702-5
DDCPWM
PS PCB CN500-5
0V
CN702-6 TPWM PS PCB CN500-6 Transfer Control Transfer +5V Output
0V
83
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN702-7 TC PS PCB CN500-7
Signal Waveform
Function
+5V 0V
CN702-8
CCRMT
PS PCB CN500-8
+5V 0V
CN702-9
MGND
PS PCB CN500-9
Ground
0V
CN702-10 +24V PS/LSU Fan -1
+24V
CN702-11 nFNRDTP
PS/LSU Fan -2
+5V 0V
CN702-12 MGND
PS/LSU Fan -3
Ground
0V
CN702-13 +5VP PS PCB CN12-1
+5V
CN702-14 +5v
PS PCB CN12-2
+5V
CN702-15 +5v
PS PCB CN12-3
+5V
CN702-16 GND
PS PCB CN12-4
Ground
0V
CN702-17 GND PS PCB CN12-5 Ground
0V
CN702-18 GND PS PCB CN12-6 Ground
0V
84
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN702-19 ZCRS PS PCB CN12-7
Signal Waveform
+5V 0V
CN702-20 SSR
PS PCB CN12-8
+5V(H) 0V(L)
CN702-21 ACSW
PS PCB CN12-9
+24V ON 0V
Fuser Relay
CN702-22 +24VD1
PS PCB CN12-10
+24V
CN703 SPC PCB Signal Name Destination Pin No. CN703-1 MGND PS PCB CN10-1 Signal Waveform Ground Function
0V
CN703-2 MGND PS PCB CN10-2 Ground
0V
CN703-3 +24V PS PCB CN10-3
+24V
CN703-4
+24V
PS PCB CN10-4
+24V
CN706 SPC PCB Signal Name Destination Pin No. 1st Tray Lift CN706-1 +24VM Motor Signal Waveform Function +24 VDC Power Supply
+24V
CN706-2
LIFT1
+24V ON 0V
85
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
CN707 SPC PCB Signal Name Destination Pin No. CN707-1 +24VM CST2 PCB CN770-3 Signal Waveform Function +24 VDC Power Supply
+24V
CN707-2
MGND
Ground
0V
CN707-3 +5v CST2 PCB CN770-5
+5V
CN707-4
GND
Ground
0V
CN707-5 OP3FLT CST2 PCB CN770-7
+5V 0V
CN707-6
OP3RST
CN707-7
OP3FOT
CN707-8
OP3FCK
+5V 0V
CN707-9
OP3FLD
+5V 0V
CN707-10 OP3ENB
CN707-11 OP3CLK
+5V 0V
86
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN707-12 OP3FDIN CST2 PCB CN770-14
Signal Waveform
+5V 0V
CN707-13 ADF2
+5V
ON 0V
CN707-14 MRCLH2
+5V
ON 0V
2nd Paper Tray Intermediate Roller Clutch Drive Signal 2nd Paper Tray Lift Motor Signal
CN707-15 LIFT2
+5V
ON 0V
CN707-16 PCHK2
+5V 0V
CN707-17 CST2
+5V 0V
CN707-18 UPLIMIT2
+5V 0V
CN707-19 FDPCHK2
+5V(H) 0V(L)
2nd Paper Tray Paper Registration Detection Signal 2nd Paper Tray Jam Access Cover Open Detection Signal 2nd Paper Feed Module Detection Signal
CN707-20 JAMDOR2
+5V 0V
CN707-21 CSTOP
0V
CN707-23 +24VM CST2 PCB CN771-11
+24V
87
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN707-24 MGND CST2 PCB CN771-12
Function
0V
CN707-25 +24VM CST2 PCB CN770-15
+24V
CN707-26 MGND
Ground
0V
CN709 SPC PCB Signal Name Destination Pin No. CN709-1 PCHK1 No Paper Sensor -1 Signal Waveform Function
+5V 0V
CN709-2
GND
No Paper Sensor -2
Ground
0V
CN709-3 LDPSEN No Paper Sensor -3 Photo Sensor DC Drive Voltage
+1.2V
CN709-4
UPLIMIT
Upper Limit Sensor -1 Upper Limit Sensor -2 Upper Limit Sensor -3 1st Tray Detection Sensor -1 1st Tray Detection Sensor -2
+5V 0V
CN709-5
GND
Ground
0V
Photo Sensor DC Drive Voltage
CN709-6
LDUPLSEN
+1.2V
CN709-7
CASET
+5V 0V
CN709-8
GND
Ground
0V
88
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN709-9 LDCSTSEN 1st Tray Detection Sensor -3 CN709-10 RSEN Registration Roller Sensor -1 Registration Roller Sensor -2 Registration Roller Sensor -3
Signal Waveform
+1.2V
+5V 0V
CN709-11 GND
Ground
0V
Photo Sensor DC Drive Voltage
CN709-12 LDRRSEN
+1.2V
CN712 SPC PCB Signal Name Destination Pin No. CN712-1 LDSSN SSN PCB CN42-1 Signal Waveform Function Photo Sensor DC Drive Voltage
+1.2V
CN712-2
nA3SEN
+5V 0V
CN712-3
GND
Ground
0V
CN712-4 nB4SEN SSN PCB CN42-4
+5V 0V
CN712-5
nA5SEN
+5V 0V
CN712-6
nPEDSEN
+5V 0V
CN712-7
GND
Ground
0V
89
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN712-8 LDPED Bypass Feed No Paper Sensor -3 CN712-9 nDUPSEN Duplex Sensor -1
Signal Waveform
+1.2V
+5V 0V
CN712-10 GND
Duplex Sensor -2
Ground
0V
CN712-11 LDDUX Duplex Sensor -3 Photo Sensor DC Drive Voltage
+1.2V
CN712-14 nHFPESEN
+5V 0V
CN712-15 GND
Ground
0V
Photo Sensor DC Drive Voltage
CN712-16 LDHFPE
+1.2V
CN715 SPC PCB Signal Name Destination Pin No. CN715-1 +24VM Registration Roller Clutch -1 CN715-2 RRCLCNT Registration Roller Clutch -2 Paper Feed Clutch -1 Paper Feed Clutch -2 Signal Waveform Function +24 VDC Power Supply
+24V
+24V ON 0V
CN715-3
+24VM
+24V
CN715-4
PFCLCNT
+24V ON 0V
90
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN715-5 +24VM Bypass Feed Solenoid -1 CN715-6 HFSOL Bypass Feed Solenoid -2
Signal Waveform
+24V
+24V ON 0V
CN717 Refer to SC PC Board . CN719 SPC PCB Signal Name Destination Pin No. Duplex Solenoid CN719-1 +24VM Signal Waveform Function +24 VDC Power Supply
+24V
CN719-2
nDUXSOL
Duplex Solenoid
+24V ON 0V
CN720 SPC PCB Signal Name Destination Pin No. CN720-3 +24VM PCL PCB -1 Signal Waveform Function +24 VDC Power Supply
+24V
CN720-4
ELPCNT
PCL PCB -2
+24V ON 0V
Discharge Lamp
CN720-5
+24VM
+24V
CN720-6
TDREF
9V 4V 5V 0V
CN720-7
TDSEN
91
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN720-8 GND Toner Density Sensor -4 CN720-12 GND Waste Toner Sensor -1 Waste Toner Sensor -2 Waste Toner Sensor -3 Waste Toner Sensor -4 Waste Toner Sensor -5 Humidity Sensor -1
Function
0V
Ground
0V
CN720-13 nWTBSEN
+5V 0V
CN720-14 nTFSEN
+5V 0V
CN720-15 LDWTB
+1.2V
CN720-16 LDTF
+1.5V 0V +5V
CN720-17 +5v
CN720-18 HUMISN
Humidity Sensor -2
5V 0V
CN720-19 GND
Humidity Sensor -3
Ground
0V
CN720-20 TEMPSN Humidity Sensor -4
5V 0V
CN720-21 +24VM
Total Counter -1
+24V
CN720-22 nCTCNT
Total Counter -2
+24V 0V
92
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
CN721 SPC PCB Signal Name Destination Pin No. CN721-1 THERM1 Thermistor -1 Signal Waveform Function
5V 0V
CN721-2
THERM2
Thermistor -2
Ground
0V
CN721-3 nHEXSEN Paper Exit Sensor -1 Paper Exit Sensor -2 Paper Exit Sensor -3 Exit Fan -1
+5V 0V
CN721-4
GND
Ground
0V
Photo Sensor DC Drive Voltage
CN721-5
LDHEX
+1.2V +24V
CN721-10 +24VFL
CN721-11 nFNRDT
Exit Fan -2
+5V 0V
CN721-12 MGND
Exit Fan -3
Ground
0V
CN722 SPC PCB Signal Name Destination Pin No. CN722-1 +24VM Toner Bottle Motor -1 CN722-2 BMCNT Toner Bottle Motor -2 Toner Motor -1 Signal Waveform Function +24 VDC Power Supply
+24V
+24V ON 0V +24V
CN722-3
+24VM
93
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN722-4 SMCNT Toner Motor -2
Signal Waveform
+24V ON 0V
CN722-5
BTHP
Toner Bottle Home Position Sensor -1 Toner Bottle Home Position Sensor -2 Toner Bottle Home Position Sensor -3
+5V 0V
CN722-6
GND
Ground
0V
CN722-7
LDBTHP
+5V 0V
CN723 SPC PCB Signal Name Destination Pin No. CN723-1 +24VM Main Motor -1 Signal Waveform Function +24 VDC Power Supply
+24V
CN723-2
+24VM
Main Motor -2
+24V
CN723-3
MGND
Main Motor -3
Ground
0V
CN723-4 MGND Main Motor -4 Ground
0V
CN723-5 GND Main Motor -5 Ground
0V
CN723-6 +5v Main Motor -6
+5V
CN723-7
nMMON
Main Motor -7
+6.5V 0V
94
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
SPC PCB Signal Name Destination Pin No. CN723-8 nMMCK Main Motor -8
Signal Waveform
+6.5V 0V
CN723-9
F/R
Main Motor -9
0V
CN723-10 nMMRDY Main Motor -10
+5V 0V
CN726 SPC PCB Signal Name Destination Pin No. Key Counter CN726-1 +24VM Signal Waveform Function +24 VDC Power Supply
+24V
CN726-2
KCNT
Key Counter
+24V 0V
CN726-3
GND
Key Counter
Ground
0V
CN726-4 KCDET Key Counter
+5V DETECT 0V
CN726-5
N.C.
No Connection
CN726-6
N.C.
No Connection
95
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
+3.3V 0V
CN223-2
RESETB
LCD
CN223-3
RS
LCD
CN223-4
RW_WRB
LCD
+3.3V 0V
CN223-5
E_RDB
LCD
+3.3V 0V
CN223-6
DB0
LCD
+3.3V 0V
Data Signal
CN223-7
DB1
LCD
+3.3V 0V
Data Signal
CN223-8
DB2
LCD
+3.3V 0V
Data Signal
CN223-9
DB3
LCD
+3.3V 0V
Data Signal
CN223-10 DB4
LCD
+3.3V 0V
Data Signal
96
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
PNL1 PCB Signal Name Destination Pin No. CN223-11 DB5 LCD
Signal Waveform
+3.3V 0V
CN223-12 DB6
LCD
+3.3V 0V
Data Signal
CN223-13 DB7
LCD
+3.3V 0V
Data Signal
CN223-14 VDD
LCD
+3.3V
CN223-15 VCL
LCD
+3.3V
CN223-16 VSS
LCD
Ground
0V
CN223-17 VOUT LCD
+12.5V
CN223-18 C4+
LCD
+12.5V
Capacitor 4 Positive Connection Pin for Converter Capacitor 3 Positive Connection Pin for Converter Capacitor 1 Negative Connection Pin for Converter Capacitor 1 Positive Connection Pin for Converter Capacitor 2 Positive Connection Pin for Converter
CN223-19 C3+
LCD
+12.5V +9.5V
CN223-20 C1-
LCD
+3.3V 0V
CN223-21 C1+
LCD
+6.3V +3.3V
CN223-22 C2+
LCD
+9.5V +6.3V
97
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Signal Waveform
Function Capacitor 2 Negative Connection Pin for Converter LCD Driver Supply Voltages
+3.3V 0V
CN223-24 V1
LCD
+6.7V
CN223-25 V2
LCD
+5.3V
CN223-26 V3
LCD
+2.6V
CN223-27 V4
LCD
+1.4V
CN223-28 V0
LCD
+8V
CN223-29 PS
LCD
+3.3V
CN223-30 HPMB
LCD
+3.3V
CN230 PNL1 PCB Signal Name Destination Pin No. CN230-1 LED0 PNL2 PCB CN250-1 Signal Waveform Function PNL LED Control Signal
0V
CN230-2 KIN7 PNL2 PCB CN250-2
Key Pressed
+3.3V 0V
CN230-3
LED1
0V
98
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
PNL1 PCB Signal Name Destination Pin No. CN230-4 KIN6 PNL2 PCB CN250-4
Signal Waveform
Key Pressed
+3.3V 0V
CN230-5
LED2
0V
CN230-6 SCN0 PNL2 PCB CN250-6
Key Scan
+3.3V 0V
CN230-7
LED3
0V
CN230-8 SCN1 PNL2 PCB CN250-8
Key Scan
+3.3V 0V
CN230-9
LED4
0V
CN230-10 KIN5 PNL2 PCB CN250-10
Key Pressed
+3.3V 0V
CN230-11 LED5
0V
CN230-12 KIN4 PNL2 PCB CN250-12
Key Pressed
+3.3V 0V
CN230-13 LEDCT2
+5V 0V LED ON
CN230-14 KIN3
Key Pressed
+3.3V 0V
CN230-15 LEDCT3
+5V 0V LED ON
99
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
PNL1 PCB Signal Name Destination Pin No. CN230-16 KIN2 PNL2 PCB CN250-16
Signal Waveform
Key Pressed
+3.3V 0V
CN230-17 LEDCT4
CN230-18 BAT+
Lithium Battery
CN231 PNL1 PCB Signal Name Destination Pin No. CN231-1 +SLP PNL2 PCB CN251-1 Signal Waveform Function Energy Saver Lamp LED Power Supply
+5VP
CN231-2
nLEDSLP
+5VP 0V
CN231-3
nSLPKY
+3.3V PUSH 0V
CN231-4
GND
Ground
0V
CN231-5 LEDCT0 PNL2 PCB CN251-5
+5V 0V LED ON
+12V (+24V)
CN231-6
BZ+
CN231-7
LEDCT1
CN231-8
BZ-
100
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
PNL1 PCB Signal Name Destination Pin No. CN231-9 LED6 PNL2 PCB CN251-9
Signal Waveform
0V
CN231-10 SCN2 PNL2 PCB CN251-10
Key Scan
CN231-11 KIN0
Key Pressed
CN231-12 KIN1
Key Pressed
CN232 PNL1 PCB Signal Name Destination Pin No. CN232-1 SCN4 PNL3 PCB CN252-1 Signal Waveform Function PNL Key Signal (Scan Line)
Key Scan
CN232-2
SCN5
Key Scan
CN232-3
SCN3
Key Scan
CN232-4
SCN6
Key Scan
CN232-5
KIN3
Key Pressed
CN232-6
N.C.
No Connection
CN232-7
KIN2
Key Pressed
+3.3V 0V
101
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
PNL1 PCB Signal Name Destination Pin No. CN232-8 KIN7 PNL3 PCB CN252-8
Signal Waveform
Key Pressed
CN232-9
KIN1
Key Pressed
CN232-10 KIN0
Key Pressed
CN233 PNL1 PCB Signal Name Destination Pin No. CN233-1 +DAT PNL3 PCB CN253-1 Signal Waveform Function DATA Lamp LED Power Supply
+24V 0V
CN233-2
N.C.
No Connection
CN233-3
+ALM
+24V 0V
CN233-4
KIN4
Key Pressed
+3.3V 0V +24V 0V
CN233-5
+ACT
CN233-6
KIN5
Key Pressed
+3.3V 0V +3.3V 0V
CN233-7
nLEDACT
CN233-8
KIN6
Key Pressed
+3.3V 0V
102
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
PNL1 PCB Signal Name Destination Pin No. CN233-9 nLEDALM PNL3 PCB CN253-9
Signal Waveform
+3.3V 0V
CN233-10 LEDCT0
+5V 0V LED ON
CN233-11 nLEDDAT
+3.3V 0V
CN233-12 LED9
0V
CN233-13 LEDCT4 PNL3 PCB CN253-13
+5V 0V LED ON
CN233-14 LED8
0V
CN233-15 LEDCT3 PNL3 PCB CN253-15
+5V 0V LED ON
CN233-16 LED7
0V
CN233-17 LEDCT2 PNL3 PCB CN253-17
CN233-18 LEDCT1
CN234 PNL1 PCB Signal Name Destination Pin No. CN234-1 KIN4 PNL4 PCB CN280-1 Signal Waveform Function PNL Key Signal (Key Line)
Key Pressed
+3.3V 0V
103
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
PNL1 PCB Signal Name Destination Pin No. CN234-2 KIN5 PNL4 PCB CN280-2
Signal Waveform
Key Pressed
+3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V +3.3V 0V
CN234-3
KIN3
Key Pressed
CN234-4
KIN6
Key Pressed
CN234-5
KIN2
Key Pressed
CN234-6
KIN7
Key Pressed
CN234-7
KIN1
Key Pressed
CN234-8
SCN11
Key Scan
CN234-9
KIN0
Key Pressed
CN234-10 SCN10
Key Scan
CN234-11 SCN8
Key Scan
CN234-12 SCN9
Key Scan
CN234-13 nOPT
104
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
PNL1 PCB Signal Name Destination Pin No. CN234-14 GND PNL4 PCB CN280-14
Function
0V
105
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2.10.5. PS PC Board
CN10 Refer to SPC PC Board . CN11 Refer to SC PC Board . CN12 Refer to SPC PC Board . CN500 Refer to SPC PC Board .
106
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
+24V 0V
CN22-2
+24V
ADF Motor -2
+24V
CN22-3
IOUTA
ADF Motor -3
+24V 0V
CN22-4
OUTB
ADF Motor -4
+24V 0V
CN22-5
+24V
ADF Motor -5
+24V
CN22-6
IOUTB
ADF Motor -6
+24V 0V
CN22-7
+24VOPF
ADF Roller Clutch -1 ADF Roller Clutch -4 Feed 2 Roller Clutch -1 Feed 2 Roller Clutch -4
+24V
CN22-8
nCCLH2
+24V ON 0V +24V
CN22-9
+24VOPF
CN22-10
nCCLH1
+24V ON 0V
107
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
CN24 ADF PCB Signal Name Destination Pin No. CN24-1 +24VOPF Inverting Roller Clutch -1 CN24-2 nCCLH3 Inverting Roller Clutch -4 Signal Waveform Function +24 VDC Power Supply
+24V
+24V ON 0V
CN25 ADF PCB Signal Name Destination Pin No. CN25-1 +24VOPF Stamp Solenoid Signal Waveform Function +24 VDC Power Supply
+24V
CN25-2
nASTAMP
Stamp Solenoid
+24V ON 0V
CN26 ADF PCB Signal Name Destination Pin No. CN26-1 +24VOPC Release Lever Plate Solenoid -1 CN26-2 nAPACHG Release Lever Plate Solenoid -2 Reversing Guide 1 Solenoid -1 Reversing Guide 1 Solenoid -2 Reversing Guide 1 Solenoid -3 Duplex 2 Guide Solenoid -1 Signal Waveform Function +24 VDC Power Supply
+24V
+24V ON +24V ON 0V 0V
CN26-3
nAKEEP1
CN26-4
+24VOPC
+24V
CN26-5
nAKEEP2
+24V ON 0V
CN26-6
+24VOPF
+24V
108
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
ADF PCB Signal Name Destination Pin No. CN26-7 nAPICR Duplex 2 Guide Solenoid -2 CN27 ADF PCB Signal Name Destination Pin No. CN27-1 nAAPNT Original Detection Sensor -1 CN27-2 GND Original Detection Sensor -2 Original Detection Sensor -3
Signal Waveform
+24V ON 0V
Signal Waveform
+5V ON 0V
Ground
0V +5V
+5 VDC Power Supply
CN27-3
+5v
CN28 ADF PCB Signal Name Destination Pin No. CN28-1 nAADL1 Original Lengh Sensor 1 -1 CN28-2 GND Original Lengh Sensor 1 -2 Original Lengh Sensor 1 -3 Original Lengh Sensor 2 -1 Original Lengh Sensor 2 -2 Original Lengh Sensor 2 -3 Signal Waveform Function Original Length Detection Signal
+5V ON 0V
Ground
0V +5V
+5 VDC Power Supply
CN28-3
+5v
CN28-4
nAADL2
+5V ON 0V
CN28-5
GND
Ground
0V +5V
+5 VDC Power Supply
CN28-6
+5v
109
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
ADF PCB Signal Name Destination Pin No. CN28-7 nAB4S SNS PCB CN41-4
Signal Waveform
+5V(H) 0V
CN28-8
nAA3S
+5V 0V
CN28-9
GND
Ground
0V
CN28-10 +5v SNS PCB CN41-1
+5V
CN29 ADF PCB Signal Name Destination Pin No. CN29-1 nAB1SN Read Point Sensor -1 CN29-2 GND Read Point Sensor -2 Read Point Sensor -3 ADF Cover Open Detection Sensor -1 ADF Cover Open Detection Sensor -2 ADF Cover Open Detection Sensor -3 Signal Waveform Function Read Point Detection Signal
+5V ON 0V
Ground
0V +5V
+5 VDC Power Supply
CN29-3
+5v
CN29-4
nAOAC
+5V OPEN 0V
CN29-5
GND
Ground
0V +5V
+5 VDC Power Supply
CN29-6
+5v
110
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
CN30 ADF PCB Signal Name Destination Pin No. CN30-1 nAEJC Eject Sensor -1 Signal Waveform Function
+5V ON 0V
CN30-2
GND
Eject Sensor -2
Ground
0V
CN30-3 +5v Eject Sensor -3
+5V
CN30-4
nAB2SN
Duplex Eject Sensor -1 Duplex Eject Sensor -2 Duplex Eject Sensor -3 ADF Exit Cover Sensor -1 ADF Exit Cover Sensor -2 ADF Exit Cover Sensor -3
+5V ON 0V
CN30-5
GND
Ground
0V +5V
+5 VDC Power Supply
CN30-6
+5v
CN30-7
nAREV
+5V OPEN 0V
CN30-8
GND
Ground
0V +5V
+5 VDC Power Supply
CN30-9
+5v
111
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
+24V
CN772-2
MGND
Ground
0V
CN772-3 +5v CST3 PCB CN807-3
+5V
CN772-4
GND
Ground
0V
CN772-5 OP3RST CST3 PCB CN807-5
+5V Reset 0V
CN772-6
OP3FLT
+5V 0V
CN772-7
OP3FCK
CN772-8
OP3FOT
CN772-9
OP3ENB
CN772-10 OP3FLD
+5V 0V
112
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
CST2 PCB Signal Name Destination Pin No. CN772-11 OP3FDIN CST3 PCB CN807-11
Signal Waveform
+5V 0V
CN772-14 +24VM
+24V
CN772-13 GND
Ground
0V
CN773 CST2 PCB Signal Name Destination Pin No. CN773-1 +24VM Paper Feed Clutch -1 CN773-2 ADF2 Paper Feed Clutch -2 Signal Waveform Function +24 VDC Power Supply
+24V
+24V ON 0V +24V
CN773-3
+24VM
CN773-4
MRCLH2
+24V ON 0V
CN774 CST2 PCB Signal Name Destination Pin No. CN774-1 +24VM 2nd Tray Lift Motor Signal Waveform Function +24 VDC Power Supply
+24V
CN774-2
LIFTM2
+24V ON 0V
113
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
CN775 CST2 PCB Signal Name Destination Pin No. CN775-1 PCHK2 No Paper Sensor -1 Signal Waveform Function
+5V 0V
CN775-2
GND
No Paper Sensor -2
Ground
0V
CN775-3 LDPHK2 No Paper Sensor -3 Photo Sensor DC Drive Voltage
+1.2V
CN775-4
UPLMT2
+5V 0V
CN775-5
GND
Ground
0V
Photo Sensor DC Drive Voltage
CN775-6
LDUPL2
+1.2V
CN776 CST2 PCB Signal Name Destination Pin No. CN776-1 FDPCHK2 Registration Sensor -1 CN776-2 GND Registration Sensor -2 Registration Sensor -3 Signal Waveform Function
+5V 0V
0V
Photo Sensor DC Drive Voltage
CN776-3
LDFPCHK2
+1.2V
114
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
CN777 CST2 PCB Signal Name Destination Pin No. CN777-1 nCST2 2nd Tray Detection Sensor -1 CN777-2 GND 2nd Tray Detection Sensor -2 2nd Tray Detection Sensor -3 Signal Waveform Function
+5V 0V
Ground
0V
Photo Sensor DC Drive Voltage
CN777-3
LDCST2
+1.2V
CN778 CST2 PCB Signal Name Destination Pin No. CN778-1 JAMDOR2 Jam Cover Open Sensor -1 CN778-2 GND Jam Cover Open Sensor -2 Jam Cover Open Sensor -3 Signal Waveform Function 2nd Paper Tray Jam Access Cover Open Detection Signal Ground
+5V OPEN 0V
0V
Photo Sensor DC Drive Voltage
CN778-3
LDJAM2
+1.2V
115
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
+5V 0V
CN800-2
GND
No Paper Sensor -2
Ground
0V
CN800-3 LDPHK3 No Paper Sensor -3 Photo Sensor DC Drive Voltage
+1.2V
CN800-4
UPLIMIT3
+5V 0V
CN800-5
GND
Ground
0V
Photo Sensor DC Drive Voltage
CN800-6
LDUPL3
+1.2V
CN801 CST3 PCB Signal Name Destination Pin No. CN801-1 CST3 3rd Tray Detection Sensor -1 CN801-2 GND 3rd Tray Detection Sensor -2 3rd Tray Detection Sensor -3 Signal Waveform Function
+5V 0V
Ground
0V
Photo Sensor DC Drive Voltage
CN801-3
LDCST3
+1.2V
116
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
CN802 CST3 PCB Signal Name Destination Pin No. CN802-1 JAMDOR3 Jam Cover Open Sensor -1 CN802-2 GND Jam Cover Open Sensor -2 Jam Cover Open Sensor -3 Signal Waveform Function
+5V 0V
3rd Paper Tray Jam Access Cover Open Detection Signal Ground
0V
Photo Sensor DC Drive Voltage
CN802-3
LDJAM3
+1.2V
CN803 CST3 PCB Signal Name Destination Pin No. CN803-1 FDPCHK3 Registration Sensor -1 CN803-2 GND Registration Sensor -2 Registration Sensor -3 Signal Waveform Function 3rd Paper Tray Paper Registration Detection Signal Ground
+5V 0V
0V
Photo Sensor DC Drive Voltage
CN803-3
LDFPCHK3
+1.5V
CN804 CST3 PCB Signal Name Destination Pin No. CN804-1 +24VM 3rd Tray Lift Motor Signal Waveform Function +24 VDC Power Supply
+24V
CN804-2
nLIFTM3
+24V 0V
CN805 CST3 PCB Signal Name Destination Pin No. CN805-1 +24VM 3rd Tray Drive Motor -1 Signal Waveform Function +24 VDC Power Supply
+24V
117
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
CST3 PCB Signal Name Destination Pin No. CN805-2 MGND 3rd Tray Drive Motor -2 CN805-3 N.C. 3rd Tray Drive Motor -3 3rd Tray Drive Motor -4 3rd Tray Drive Motor -5
Function
0V
No Connection
CN805-4
P/S
+5V 0V +5V 0V
Motor Start/Stop
CN805-5
LD
CN806 CST3 PCB Signal Name Destination Pin No. CN806-1 +24VM Paper Feed Clutch -1 CN806-2 ADF3 Paper Feed Clutch -2 Intermediate Roller Clutch -1 Intermediate Roller Clutch -2 Signal Waveform Function +24 VDC Power Supply
+24V
+24V 0V
CN806-3
+24VM
+24V
CN806-4
MRCLH3
+24V 0V
CN808 CST3 PCB Signal Name Destination Pin No. CN808-1 +24VM CST2 PCB CN770-3 Signal Waveform Function +24 VDC Power Supply
+24V
CN808-2
MGND
Ground
0V
118
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
CST3 PCB Signal Name Destination Pin No. CN808-3 +5v CST2 PCB CN770-5
Signal Waveform
+5V
CN808-4
GND
Ground
0V
CN808-5 N.C. CST2 PCB CN770-7 No Connection
CN808-6
N.C.
No Connection
CN808-7
N.C.
No Connection
CN808-8
N.C.
No Connection
CN808-9
N.C.
No Connection
CN808-10 N.C.
No Connection
CN808-12 N.C.
No Connection
CN808-13 ADF4
+24V ON 0V +24V ON 0V
CN808-14 MRCLH4
CN808-15 LIFT4
+5V 0V
119
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
CST3 PCB Signal Name Destination Pin No. CN808-16 PCHK4 CST2 PCB CN771-4
Signal Waveform
Function
+5V 0V
CN808-17 CST4
+5V 0V
CN808-18 UPLIMIT4
+5V 0V
CN808-19 FDPCHK4
+5V 0V
4th Paper Tray Paper Registration Detection Signal 4th Paper Tray Jam Access Cover Open Detection Signal 4th Paper Feed Module Detection Signal
CN808-20 JAMDOR4
+5V 0V
CN808-21 CSTOP4
0V
CN808-23 +24VM CST2 PCB CN771-11
+24V
CN808-24 MGND
Ground
0V
CN808-25 N.C. CST2 PCB CN770-15 No Connection
CN808-26 N.C.
No Connection
120
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
+5V
CN391-2
GND
Ground
0V
CN391-3 +24V MJR PC Board CN25-3
+24V
CN391-4
pCMLD
+5V(H) OFF
ON
Line Switching Relay Drive Signal H : CML On 0V(L) L : CML Off External Phone Off-Hook Detection Signal H : On Hook L : Off Hook Ring Detection Signal
CN391-5
nHKOF
+5V(H) 0V(L)
CN391-6
nCTON
CN391-7
AGND
0V
CN392 FXB PCB Signal Name Destination Pin No. CN392-1 L2 MJR PC Board CN22-1 Signal Waveform Function Line Signal
CN392-3
L1
Line Signal
121
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
CN393 FXB PCB Signal Name Destination Pin No. CN393-1 pSPKOT Speaker -1 Signal Waveform Function Line Dial Tone Signal
CN393-2
GND
Speaker -2
Ground
0V
122
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
123
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
3 Troubleshooting
3.1. Error Codes (For Copier)
The self-diagnostic functions detect troubles in the important components of the copier. When any trouble occurs, the copier stops.
3.1.1.
U21 U90
Note: Uxx, and a message will appear on the Panel Display. User Error Codes (U Code) Table Item Possible Cause(s) Key Counter 1. Card Key not installed. 2. Key Counter Harness disconnected. 3. Department Code not assigned. Close Front Cover 1. Front Cover / Side Cover open. 2. Front Cover / Side Cover Sensor disconnected. 3. Front Cover / Side Cover Sensor defective 4. PS connector disconnected. 5. PS defective. 6. SPC PCB connector disconnected. 7. SPC PCB defective. Close Tray Cover 1. Tray Cover open. 2. Tray Unit incorrectly installed. 3. Tray Unit connector disconnected. 4. Tray Unit Sensor disconnected. 5. Tray Unit Sensor defective. 6. PS connector disconnected. 7. PS defective. 8. CST2/CST3 PCB connector disconnected. 9. CST2/CST3 PCB defective.
Code U00
U01
U07
124
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Code U13
U14 U15
U21
U22
U25 U90
User Error Codes (U Code) Table Item Possible Cause(s) Add Toner 1. Toner Bottle incorrectly installed. 2. Low Toner. 3. Toner Sensor disconnected. 4. Toner Sensor defective. 5. SPC PCB connector disconnected. 6. SPC PCB defective. Replace Toner Waste 1. Toner Waste Container full. Container (See Sect. 3.5.3. of the Service Manual) No Toner Waste Container 1. Toner Waste Container not installed. 2. Toner Waste Container Sensor disconnected. 3. Toner Waste Container Sensor defective. No Developer Unit 1. Developer Unit not installed. Total Copy Limit Over 1. Department Copy Counter full. Close ADF Cover 1. ADF Cover open. 2. ADF not installed correctly. 3. ADF Cover Sensor disconnected. 4. ADF Cover Sensor defective. 5. PS connector disconnected. 6. PS defective. Close ADF 1. ADF, and ADF Cover open. 2. ADF Sensor disconnected. 3. ADF Sensor defective. Close ADF Exit Cover 1. ADF Exit Cover open. 2. ADF not installed correctly. 3. ADF Exit Cover Sensor disconnected. 4. ADF Exit Cover Sensor defective. 5. PS connector disconnected. 6. PS defective. Shake Toner Bottle 1. Toner blocked in the Toner Bottle. Replace Battery 1. Internal battery requires replacement.
125
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
3.1.2.
C D2 D3 D4
Jam Location ADF / i-ADF / Scanner Paper Transport / Exit Area Paper Entry Area 2nd Paper Tray 3rd Paper Tray 4th Paper Tray
126
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
ADU Sensor
Registration Sensor
127
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Paper Transport / Exit / Entry / Feed Unit Area Jam Error Codes (J Code) Table Contents Section The Registration Sensor does not detect paper within a predetermined time after the B paper starts feeding. (Sheet Bypass) The Registration Sensor does not detect paper within a predetermined time after the Paper Feed Roller starts rotating. (1st Paper Tray) The 2nd Paper Tray Path Sensor does not detect paper within a predetermined time D2 after the Paper Feed Roller starts rotating. (2nd Paper Tray) The 3rd Paper Tray Path Sensor does not detect paper within a predetermined time D3 after the Paper Feed Roller starts rotating. (3rd Paper Tray) The 4th Paper Tray Path Sensor does not detect paper within a predetermined time D4 after the Paper Feed Roller starts rotating. (4th Paper Tray) The Registration Sensor does not detect paper within a predetermined time after the B, D2 2nd Paper Tray Path Sensor is activated. (2nd Paper Tray) The Registration Sensor did not detect paper within a predetermined time after the D3 3rd Paper Tray Path Sensor is activated. (3rd Paper Tray) The Registration Sensor did not detect paper within a predetermined time after the D4 4th Paper Tray Path Sensor is activated. (4th Paper Tray) The 2nd Paper Tray Path Sensor does not go off within a predetermined time after B, D2 the Paper Tray Path Sensor is activated. The 3rd Paper Tray Path Sensor does not go off within a predetermined time after the D3 Paper Tray Path Sensor is activated. The 4th Paper Tray Path Sensor does not go off within a predetermined time after the D4 Paper Tray Path Sensor is activated. The Registration Sensor does not detect within a predetermined time after the ADU B Sensor is activated. The 2nd Paper Tray Path Sensor detect paper at the time of the initials. B, D2 The 3rd Paper Tray Path Sensor detect paper at the time of the initials. D2, D3 The 4th Paper Tray Path Sensor detect paper at the time of the initials. D3, D4 The Registration Sensor does not go off within a predetermined time after the Sensor B is activated. (Sheet Bypass) The Registration Sensor does not go off within a predetermined time after the Sensor is activated. (Except Sheet Bypass) The Registration Sensor does not go off within a predetermined time after the ADU Sensor is activated. (DP-8020E) The Registration Sensor detects paper during non-printing mode. The Paper Exit Sensor keeps detecting paper after a predetermined time, during non-printing mode. The Paper Exit Sensor does not go off within a predetermined time after the Sensor is activated. The Paper Exit Sensor does not detect paper within a predetermined time after the Registration Sensor is activated. B
Code J00 J01 J02 J03 J04 J07 J08 J09 J12 J13 J14 J19 J22 J23 J24 J30 J31 J32 J33 J45 J46 J48
J70-79 (See the following table below) J82 The ADU Sensor does not detect paper within a predetermined time after the Duplex Feed Roller starts rotating. J85 The ADU Sensor does not go off within a predetermined time after the Sensor is activated. J87 The ADU Sensor detects paper during non-printing mode. J90 Abnormal Paper Jam: During printing the Front Door was opened, etc.
B, C, D
128
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Code J91 J92-94 (See the following table below) J95 The paper size of a Tray differs from the Machine setting size. J97 After passing the Registration Sensor (Roller), the Paper does not clear the sensor within a predetermined time period. J98 No VRDY Signal after a predetermined time has lapsed. J99 No VSYNC Signal within a predetermined time after VRDY Signal is activated. i-ADF / ADF Area Jam Error Codes (J Code) Table Contents The Read Point Sensor does not detect paper within a predetermined time after the original starts feeding. The Read Point Sensor keeps detecting paper within a predetermined time after scanning starts. The Eject Sensor does not detect paper within a predetermined time after the Read Point Sensor is activated. 1. The Eject Sensor keeps detecting paper within a predetermined time after scanning starts. 2. The Eject Sensor keeps detecting paper within a predetermined time after the Read Point Sensor is deactivated. The Duplex Eject Sensor does not detect paper within a predetermined time after scanning starts. The Duplex Eject Sensor keeps detecting paper within a predetermined time after 2-Sided Scanning. The Read Point Sensor keeps detecting paper in the ADF. The Read Point Sensor does not detect paper in the ADF. The paper remained in the ADF. The ADF does not go off after the predetermined time. Unexpected Jam timing (i.e. Original is too short, Ledger / A3 size original is fed without being recognized that the length is abnormal for a Fax Transmission, etc.)
Jam Error Codes (J Code) Table Contents A Paper Tray was pulled out while feeding paper.
Section C B
Section A
A (i-ADF only)
129
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
3.1.3.
Code E1- 01
E1- 20
E1- 22
E1- 31
E2- 02 Lift Motor Rotation (2nd Paper Tray) E2- 03 Lift Motor Rotation (3rd Paper Tray) E2- 04 Lift Motor Rotation (4th Paper Tray)
E2: Lift DC Motor Error Possible Cause(s) 1. Level Sensor connector disconnected. 2. Level Sensor defective. 3. Lift Mechanism defective. 4. Lift Motor connector disconnected. 5. Lift Motor defective. 6. SPC PCB connector disconnected. 7. SPC PCB defective. 8. PS defective. 1. Level Sensor connector disconnected. 2. Level Sensor defective. 3. Lift Mechanism defective. 4. Lift Motor connector disconnected. 5. Lift Motor defective. 6. SPC PCB connector disconnected. 7. SPC PCB defective. 8. CST2 PCB connector disconnected. 9. CST2 PCB defective. 10. CST3 PCB connector disconnected. 11. CST3 PCB defective. 12. PS defective.
130
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
E2: Lift DC Motor Error Code Function Possible Cause(s) E2- 10 System Console Drive Motor 1. Drive Mechanism defective. Rotation 2. Drive Motor connector disconnected. 3. Drive Motor defective. 4. CST2 PCB connector disconnected. 5. CST3 PCB connector disconnected. 6. CST3 PCB defective. 7. PS connector disconnected. 8. PS defective. 9. SPC PCB connector disconnected. 10. SPC PCB defective. E3: Development System Error Code Function Possible Cause(s) E3- 01 Toner Bottle Motor Rotation 1. Toner Bottle Motor connector disconnected. 2. Toner Bottle Motor defective. 3. Toner Bottle Motor Drive Mechanism defective. 4. Toner Bottle installed incorrectly. 5. SPC PCB connector disconnected. 6. SPC PCB defective. 7. Toner Bottle Home Position Sensor connector disconnected. 8. Toner Bottle Home Position Sensor defective. 1. Toner Screw Motor defective. E3- 02 Toner Screw Motor Over 2. Toner Screw Motor Drive Mechanism defective. Current 3. SPC PCB defective. E3- 03 Toner Density Sensor Gain 1. Sensor connector disconnected. 2. Sensor defective. 3. SPC PCB connector disconnected. 4. SPC PCB defective. E3- 10 High Voltage Power Supply 1. PS connector disconnected. leak (1) - Grid Charge Voltage 2. PS defective. 3. SPC PCB connector disconnected. 4. SPC PCB defective. 5. Corona Wire is abnormal. (Check for: contamination with foreign particles, broken, not installed in the proper position, or loose tension) E3- 20 Main Motor Rotation 1. Drive Mechanism defective. 2. Main Motor connector disconnected. 3. Main Motor defective. 4. SPC PCB connector disconnected. 5. SPC PCB defective. 6. PS defective.
131
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Code E4- 01
E4- 02
E4- 10
E4: Fuser Unit Error Function Possible Cause(s) Fuser Warm-up Temperature 1. Fuser Thermistor dirty. 2. Thermistor position incorrect. 3. Thermistor defective. 4. Thermistor connector disconnected. 5. Fuser Lamp connector disconnected. 6. Fuser Lamp defective. 7. Fuser Thermostat defective. 8. Thermal Fuse defective. 9. SPC PCB connector disconnected. 10. SPC PCB defective. 11. Fuser temperature low. (Adjust F6-31) 12. Incorrect SC PCB is installed. 13. Incorrect SPC PCB is installed. Fuser Paper Jam 1. Paper Jam in Fuser Unit. 2. Paper Exit Sensor disconnected. 3. Paper Exit Sensor defective. 4. SPC PCB connector disconnected. 5. SPC PCB defective. Fuser Fan Motor Rotation 1. Fuser Fan connector disconnected. 2. Fuser Fan defective. 3. SPC PCB connector disconnected. 4. SPC PCB defective. 5. PS defective.
E5: System Error Code Function E5- 11 Printer Engine Communication Abnormal E5- 17 Scanner Synchronization E5- 19 Scanner Line Synchronization E5- 40 Sort Memory Abnormal Possible Cause(s) 1. SPC PCB connector disconnected. 2. SPC PCB defective. 3. SC PCB connector disconnected. 4. SC PCB defective. 1. Sort Memory defective. 2. SC PCB connector disconnected. 3. SC PCB defective. 1. Total Counter connector disconnected. 2. Total Counter defective. 3. SPC PCB connector disconnected. 4. SPC PCB defective. 1. Cooling Fan connector disconnected. 2. Cooling Fan defective. 3. SPC PCB connector disconnected. 4. SPC PCB defective. 5. PS defective.
E7: Optional Unit Error Code Function E7- 90 Hardware Key Abnormal Check Points 1. Incorrect Hardware Key installed. 2. Hardware Key defective.
132
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
E13: Out of Toner Code Function E13 No Toner Detection Possible Cause(s) 1. Out of Toner. 2. Toner Bottle not installed. 3. Toner Bottle not installed correctly. 4. Toner Sensor disconnected. 5. Toner Sensor defective. 6. SPC PCB connector disconnected. 7. SPC PCB defective.
3.1.4.
Technician Warning
The following message will be displayed in the event. LCD Message HDD OPTION REQUIRES ADDITIONAL SORT MEM Possible Cause(s) 1. Additional Sort memory is not installed. DA-SM16 (16 MB) DA-SM64 (64 MB) DA-SM28 (128 MB) 2. Make sure the SDRM PC Board was installed properly. 1. Incorrect SC PCB is installed. SC PCB for DP-8020E SC PCB for DP-8020P SC PCB for DP-8016P 2. SPC PCB defective.
MACHINE ID ERROR
133
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
3.2.
031
XMT COPY
401
XMT
DCN was returned from receiver while transmitter is waiting for CFR, or FTT.
402
XMT
403
RCV (Polling)
DCN was returned from receiver while transmitter is waiting for NSF/DIS. Transmitter had no polling function.
Wrong number dialed, and the START button was pushed. Telephone line disconnected while dialing. FXB PCB (Modem), or MJR PCB defective. Receiver defective. (It may only be transmitting CED) Your machine's ID Number is not programmed. Possible incompatibility, or incorrect Password (Password Reception, Selective Receive). Mailbox full. Receiver working in non-CCITT mode only. (Possible incompatibility) "POLLED=ON" (polling XMT ready) not set at the transmitter. Document to be transmitted not placed at the transmitter. Receiver defective. (Modem, MJR PCB, etc.) FXB PCB, or MJR PCB defective. Receiver disconnects line during first NSS (or DCS) transmitted.
404
XMT
Transmitter sent NSS (or DCS) followed by TCF three times, but the receiver did not respond. (CFR, or FTT is usually returned)
134
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Code 405
Mode XMT
406
407
408
XMT
409
XMT
410
RCV
411
RCV (Polling)
412
G3 RX
414
RCV (Polling)
415
416
417
RCV
Fax Information Codes Phase Description of Problem Possible Cause(s) B Transmitter received FTT after it Line quality poor. (TCF is damaged due transmitted TCF at 2400 bps. to line noise) Received RTN after Receiver defective. (Modem, MJR PCB, communicating at 2400 bps. etc.) FXB PCB, or MJR PCB defective. B XMT-Password mismatched. RCV- XMT, RCV password does not match. Password mismatched. Selective Last 4 digits of TSI does not match with RCV incomplete. the last 4 digits of Auto Dial telephone number. D Transmitter received no response Receiver defective. (No paper, paper after it transmitted post message, jamming, etc.) such as EOP, MPS, EOM, etc...or Receiver ceased receiving because of received DCN. excessive errors. (Line quality poor) FXB PCB (Modem), or MJR PCB defective. D Transmitter received RTN after it Receiver receives data with errors. transmitted EOP, MPS, or EOM. (Line quality poor) Receiver defective. (Modem, MJR PCB, etc.) FXB PCB, or MJR PCB defective. D Transmitter receives PIN after it Receiver receives data with error due to transmitted a post message, such poor line quality, and receiving operator as EOP, MPS, EOM, etc. requests voice contact. Receiver defective. (Modem, MJR PCB, etc.) FXB PCB, or MJR PCB defective. D Received DCN while waiting for Interface, or line faulty. post command. (EOP, MPS, EOM, Transmitter defective. etc.) B Received DCN after transmitting Transmitter not ready for polling NSC. communication. Password does not match between transmitter, and receiver. B, D No response within 12 seconds in Transmitter defective. NSS/DCS/MPS wait state. (After FXB PCB defective. transmitting FTT) B No response received after Password does not match between transmitting 3rd NSC. transmitter, and receiver. Transmitter defective. (No original, document jam, etc.) B Remote side attempted to receive Inform the remote side that your message from your machine in machine does not have the polling polling communication. transmission feature. D Receiver did not detect post Transmitter defective. command, such as EOP, MPS, Line quality poor. (RTC signal distorted EOM, etc. due to line noise) FXB PCB, or MJR PCB defective. C Receiver returned RTN in Line quality poor. (There are excessive response to post message. errors in received data) FXB PCB, or MJR PCB defective.
135
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Code 418
Mode RCV
420
RCV
Fax Information Codes Phase Description of Problem Possible Cause(s) C Receiver transmitted PIN in Line quality poor. (There are excessive response to PRI-Q from errors in received data) transmitter. (Transmitting operator FXB PCB, or MJR PCB defective. requests voice contact) B T1 timer (35 sec.) elapsed without Wrong number dialed. detecting 300 bps signal. (Non-facsimile communication) Transmitter defective. FXB PCB, or MJR PCB defective. B Busy Tone was detected after Remote station disconnected the line. sending NSF Signal. Wrong number was dialed. B Content of NSF (or DIS), or NSC Incompatible content (or DTC) was invalid. B DCN received to NSF/CSI/DIS Interface is incompatible. transmitted. B, D T.30 Protocol abnormal. Defective remote station. B CD (response from Modem) did not turn OFF within 180 sec. after receiver detected FLAG signal. DCN received after transmitting FTT. Received relay transfer request, or confidential document to distribute to an end receiving station, or all confidential mailboxes are used. Remote unit does not have Relayed XMT, or Confidential Comm. capability. Failed training in Phase C. Remote unit defective. FXB PCB, or MJR PCB defective. Transmitter defective, or incompatible. Line quality poor.
436 456
C B
490
RCV
494
RCV
495
XMT RCV
Transmitter defective. Line quality poor. (EOL damaged due to line noise) FXB PCB, or MJR PCB defective. C During reception, CD turned OFF, Line disconnected. or continued ON for long time. Transmitter defective. During communication, lost loop - FXB PCB, or MJR PCB defective. current. C CS of modem is not able to turn FXB PCB defective. ON. B Incompatible Modem on the Remote unit. B, C, D During reception, CD turned OFF, Line disconnected. or continued ON for long time. Transmitter defective. During communication, lost loop - FXB PCB, or MJR PCB defective. current.
Sum of error lines exceeded the limit (Function Parameter No. 70) of 64 lines. Interval between two EOLs was more than 10 sec. when receiver received message data.
Line quality poor. (Training signal distorted due to line noise) FXB PCB, or MJR PCB defective. Line quality poor. FXB PCB, or MJR PCB defective.
136
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Code 503 504 505 540 541 542 543 544 550 554 555 570
Mode XMT/ RCV(V.34) RCV/V.34 (Polling) XMT/V.34 (Polling) XMT ECM XMT ECM XMT ECM XMT ECM XMT ECM RCV ECM RCV ECM RCV ECM RCV
Fax Information Codes Phase Description of Problem Possible Cause(s) B, C, D CS of modem is not able to turn FXB PCB defective. ON during training. Line disconnected. B Polling is rejected from the remote No polling original set. station. B Polling XMT is rejected. No polling original set. B D D D D C D D B No response after transmitting 3rd CTC, or DCN received. No response after transmitting 3rd EOR, or received DCN. No response to the 3rd RR transmitted, or received DCN. T5 timer (60 sec.) elapsed without MCF. Stopped Transmission after EOR Transmission. Timer between frames in phase C has elapsed. Transmitted ERR after receiving EOR. Transmitted PIN after receiving EOR. Password, or machine code did not match during remote diagnostic communication. Remote unit did not have the remote diagnostic function. Sub-address transmission to a unit that has their DIS bit 49 (NSF bit 155) OFF. Sub-address Password transmission to a unit that has their DIS bit 50 (NSF bit 156) OFF. Sub-address SEP (for Polling) transmission to a unit that has their DIS bit 47 (NSF bit 130) OFF. ADF Door was opened during ADF transmission. No original was in the ADF. (Builtin dialer engaged) Redial count over. Incompatible interface. Faulty line. MJR PCB abnormal. Remote unit abnormal. Remote unit abnormal. Faulty line. MJR PCB abnormal. Defective remote station. Faulty line. Faulty line, and Operator Call requested by RX side.
571 580
XMT XMT
B B
Sub-address transmission to a unit that has no Sub-address function. Sub-address transmission to a unit that has no Sub-address function. Sub-address transmission to a unit that has no Sub-address function.
581
XMT
582
XMT
601 623
XMT XMT A
630
Operator removed the original from the ADF after dialing was completed. Original was not set properly in the ADF. No dial tone detected. Sensor did not detect dial tone. (Country dependent) Busy tone is detected. (Country dependent) T1 timer (355 sec) elapsed without a signal from the receiver.
631
XMT
137
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Code 634
Mode XMT
Phase PSTN
638
XMT
700 712
714
LAN
715
LAN
716
XMT
LAN
717 718
XMT XMT
LAN LAN
719
RCV
LAN
725 726
LAN LAN
Fax Information Codes Description of Problem Possible Cause(s) Redial count over with no response, or busy tone was not detected. Note: U.S.A., and Canadian models will redial only once if a busy tone is not detected. Power turned Off with applicable Power switched Off. data in memory, or during Power failure occurred. communication. Communication terminated by Operator pressing the "STOP" key. Unknown email address replied Mail Server received an incorrect email from the Mail Server. address. (Dependent on Server's Mail application) LAN Interface error. The 10Base-T/100Base-TX cable not Cannot logon to the LAN. connected. An unexpected LAN problem occurred. TCP/IP connection timed out. Incorrect IP Address set. Verify the IP Address, Default Router IP Address, SMTP Server IP Address. Cannot logon to the LAN. Incorrect SMTP Server IP Address set. No email application activated on the Mail Server. Incomplete SMTP Protocol Mail Servers hard disk may be full. transmission. Mail Server defective. Page Memory Overflow occurred Check the document size, and while receiving printing data. The resolution. paper size selected within your Ask originator to resend in a supported application to print is larger than size, and resolution. the paper size loaded in the paper tray(s). Received data via LAN is in a Ask the originator to resend with a format that is not supported. supported file attachment: * In a TIFF-F format. * Image data conforming to A4/Letter size. Unable to connect to the POP Incorrect POP Server address set. Server. POP Server is down. Unable to login to the POP Server. Incorrect User Name, or Password set. Failed to obtain the Network DHCP not available. Parameters (such as: IP Address, (Contact the Network Administrator.) Subnet Mask, Default Gateway IP Address, etc.) from the DHCP server. DNS Server connection timed out. Incorrect DNS Server address set. DNS Server is down. Received an error response from Incorrect POP Server address set. the DNS Server. Incorrect SMTP Server address set.
138
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Code 727
Mode XMT
Phase LAN
728
XMT
LAN
729
XMT
LAN
730
RCV
LAN
731
RCV
LAN
800
Relay Comm.
PSTN
Conf. XMT Conf. Polling Relay Comm. 815 Conf. RCV 816 Conf. Polled 825 870 879 Conf. RCV Conf. Polled MEM XMT Multi-Copy Memory RCV
814
PSTN
Fax Information Codes Description of Problem Possible Cause(s) Received an Error, or No Remote Internet Fax Errors: Busy, or Response from the Remote Job Number Overflow for Relay XMT. Internet Fax. (SMTP Direct XMT) (Retry is possible) Remote Internet Fax Errors: Memory Overflow, or No Power. (Retry is not possible) Failed to authenticate (SMTP SMTP AUTHENTICATION, User Name, AUTHENTICATION) when and/or Password are incorrect. connecting with the SMTP server. (Contact the Network Administrator.) Unable to program the Internet Verify that the Fax Parameter #158 is parameters, or the autodialer via set to Valid. Email from a PC. Dialer full while Relayed Dial buffer for manual number dialing Transmission Request was (70 stations) is being used. received. Unable to dial Deleted the registered station name before dialing with Timer Controlled Communications, etc. The machine was requested to relay a document but has no Relay Hub capability. The remote station does not have Relay XMT nor Confidential Communication capability.
RCV XMT
PSTN Mailbox full. PSTN The received Polling Password did not match. PSTN Parameter settings of the remote station are not properly set. PSTN Memory overflow occurred while LAN storing documents into memory. PSTN Memory overflow occurred during substitute memory reception. LAN Memory overflow. Mail Server sent a reset command while downloading the data to the machine. File Access Error. File Access Error. LAN Memory file access error. PSTN Memory file access error. LAN Memory file access error.
Memory overflow on the Fax side. Memory overflow on the Fax side. Mail server aborted the download (Busy with other higher priority jobs).
139
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
memo
140
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4 Service Modes
4.1. Service Modes (For Copier)
These Service Modes are provided to assist the technician in checking for abnormalities in the copier, and a means of making adjustments to the Input/Output of major components. Caution: The factory default parameters are preset (destination dependent) for optimum performance, and in compliance with the local telecommunication regulations/standards, and do not need to be changed. Changing some of these parameters may cause the unit to be no longer compliant, or become inoperable.
4.1.1.
1. To select the Service Mode The service mode is selected when FUNCTION, ORIGINAL SIZE, and 3 keys are sequentially pressed, then F1 will appear in the display. 2. To exit the Service Mode The service mode is reset when the FUNCTION, and CLEAR keys are pressed simultaneously.
4.1.2.
Item 00 CCD Test 01 LCD/LED Test 02 Page Memory Test 03 Print Test Pattern 1 04 Print Test Pattern 2 05 Print Test Pattern 3 06 Print Test Pattern 4
Function This test is used for checking the CCD. This test is used for checking the LCD, and LEDs. This test is used for checking the Page Memory. Prints the pattern for setting the Paper position alignment. Prints the Slant pattern for setting the Paper position alignment. Prints the Grid pattern for setting the Paper position alignment. Prints the pattern for setting the Duplex Paper position alignment. One sheet is copied when the Start key is pressed. Multi copies are made when the Start key is pressed. The functioning of Input / Output items (selected item numbers) is checked. Various function settings (selected by code numbers) can be changed. Various function settings (selected by code numbers) can be adjusted. Electronic Counters for Maintenance Perform pseudo-operation of an item (selected by code numbers)
F2 F3 F4 F5 F6 F7 F8
Single Copy Test Continuous Copy Test Input / Output Status Test Function Parameters Adjust Parameters Electronic Counter Service Adjustment
141
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Service Modes (For Copier) Service Mode F9 Unit Maintenance Item Function Fax Service Mode Service Alert Tel # Firmware Version Print Device Info.
F5-00 F5-01 F5-02 F5-03 F5-04 F5-05 F5-06 F5-07 F5-08 F5-09 F5-10 F5-11 F5-12 F5-13 F5-14 F5-15 F5-16 F5-17 F5-18 F5-19
. . . . . Frequency desired . . . . . LSU startup speed LSU off timer . . . . . . . . . . . . . . . . . . . . Fuser lamp control EXIT TRAY LIMITATION REPLACE DRUM UNIT Printer fan extension PAPER OUT INDICATOR Paper size (tray1) Paper size (tray2) Paper size (tray3) Paper size (tray4) . . . . . T Corona Current Adj
F5-50 F5-51 F5-52 F5-53 F5-54 F5-55 F5-56 F5-57 F5-58 F5-59 F5-60 F5-61 F5-62 F5-63 F5-64 F5-65 F5-66 F5-67 F5-68 F5-69
Auto contrast adj. Dept. Counter (COPY) Dept. Counter (FAX) 2-sided auto shift Margin reduction Margin value default Edge value default Book value default U14 Clear Oper.add toner alarm Auto Tray selection TDC Adj.(Dev Cond.) TDC Adj.(Dev Life) U13 clear Dept. Counter (SCAN) Dept. Counter (PRINT) . . . . . . . . . . . . . . . Reduce N in 1 space
Yes Yes No No No 10mm 5mm 20mm Any Keys Stop Yes Yes Yes Any keys Yes Yes
No 120k
F5-20 ADF
F5-70 PM cycle
F6-70 . . . . . F6-71 ADF Read Scan Pos. F6-72 Original Lead ADF:S
0 0
142
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
: 32 MB : 16 MB : 2 MB
: : : : : : : : : : :
: 2082
NO. DATE & TIME ERROR CODE ERROR COUNT NO. DATE & TIME ERROR CODE ERROR COUNT -------------------------------------------------------------------------------01 MMM-dd-yyyy 11:11 J27 XX-00000008 02 MMM-dd-yyyy 11:31 J41 XX-00000140 (See Remarks) --------------------------------------------------------------------------------
-PANASONIC
****************************** -PANASONIC - ***** -
0001- ********
Remarks: XX-00000140
143
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
F7-21 COPY PRINT COUNT F7-22 COPY SCAN COUNT F7-23 PC PRINT COUNT F7-24 PC SCAN COUNT F7-25 FAX TRANSMIT COUNT F7-26 FAX RECEIVE COUNT F7-27 FAX PRINT COUNT
144
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.1.3.
Set the machine to service mode, and press "4" key on the Keypad. Press the "START" key. Enter the number to activate the test then press "START" key. Press "STOP" key to cancel the test. When the CLEAR key is pressed, the selected code input will not be accepted. Press FUNCTION, and CLEAR keys simultaneously to exit the service mode. 1. Check Input F4 Mode (Check Input) Message Display Condition 7 6 5 4 3 2 1 0 Over Current is 1 detected. Normal. 0 Unit is installed. 0
No.
Function
Remarks
000 Toner Screw Motor Over Current Power Supply Fan Signal 003 Paper Tray Unit Option Detection Sensor (2nd Paper Tray) Paper Tray Detection Sensor (2nd Paper Tray) Paper Tray Detection Sensor (1st Paper Tray) NP Sensor (Sheet Bypass) Paper Length Sensor (Sheet Bypass) Size Sensor (PC1) (Sheet Bypass) Size Sensor (PC2) (Sheet Bypass)
1 1 1 1
145
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
No.
Function
004 Size Sensor (PC3) (Sheet Bypass) ADU Detection Sensor JAM Access Cover Open Detection Sensor (2nd Paper Tray) Upper Limit Sensor (2nd Paper Tray) Upper Limit Sensor (1st Paper Tray) NP Sensor (2nd Paper Tray) NP Sensor (1st Paper Tray) 005 Total Counter Detection Sensor Polygon Motor Lock Signal Main Motor Lock Signal Fuser Fan Lock Signal Toner Waste Container Detection Sensor Toner Waste Container Full Detection Sensor Toner Bottle Motor Rotation Detection Sensor 006 ADU Paper Sensor Fuser Exit Sensor Registration Sensor (2nd Paper Tray) Registration Sensor 008 Front / Left Cover Open Sensor 1
F4 Mode (Check Input) Message Display Condition 7 6 5 4 3 2 1 0 Paper is not detected. 0 Unit is connected. Cover is open. 0 0
Remarks
Upper Limit is detected. Upper Limit is detected. Paper is not detected. Paper is not detected. Counter is not detected. Normal. Normal. Normal. Toner Waste Container is detected. Toner Waste Container is full. Lock Paper is detected. Paper is detected. Paper is detected. Paper is detected. See Remarks. 1 0 0
1 1 0 0
0 0 1 0 0 0 0 0 * Front / Left Cover is closed. Signal 1 = 0 Signal 2 = 0 Right Cover is open. Signal 1 = 1 Signal 2 = 1 1
Unit is connected.
146
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
No.
Function
009 JAM Access Cover Open Detection Sensor (4th Paper Tray) Paper Tray Detection Sensor (4th Paper Tray) Upper Limit Sensor (4th Paper Tray) Paper Tray Detection Sensor (4th Paper Tray) Feed Motor Lock Signal (3rd Paper Tray) Paper Tray Detection Sensor 2 (3rd Paper Tray) Paper Tray Detection Sensor 1 (3rd Paper Tray) 010 Registration Sensor (3rd Paper Tray) JAM Access Cover Open Detection Sensor (3rd Paper Tray) Paper Tray Detection Sensor (3rd Paper Tray) Upper Limit Sensor (3rd Paper Tray) NP Sensor (3rd Paper Tray) Registration Sensor (4th Paper Tray) NP Sensor (4th Paper Tray) 011 Corona Leak Detection
Remarks
0 0
0 * Unit is connected. Signal 1 = 1 Signal 2 = 0 A different signal pattern, indicates that the unit is not connected, or CST 3 PCB is defective.
See Remarks.
0 0
Paper Tray is connected. Upper Limit is detected. Paper is not detected. Paper is detected. Paper is not detected. Leak
0 0 0 0 0
147
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
No.
Function
020 Size Sensor C (Not Used) Size Sensor B (Not Used) Size Sensor A (Not Used) Size Sensor Z (Not Used) Size Sensor Y (Not Used) Size Sensor X (Not Used) 021 Home Position Sensor ADF/Platen Cover Open Sensor ADF/Platen Cover Angle Sensor Fuser Lamp Disconnect Detection Sensor +24V Line Error Detecting Signal 030 ADF B1 Sensor ADF B2 Sensor ADF Paper Exit Detection Sensor ADF Inverting Cover Open Detection Sensor ADF Cover Open Detection Sensor ADF Detection Sensor 1
F4 Mode (Check Input) Message Display Condition 7 6 5 4 3 2 1 0 Original detected on the 1 C position. Original detected on the B position. Original detected on the 1 A position. Original detected on the 1 Z position. Original detected on the 1 Y position. Original detected on the 1 X position. Home position is 1 detected. ADF/Platen Cover is 1 open. ADF/Platen Cover is 1 open more than 30 angle. No Lighting +24V Line is ON. Original is detected. Original is detected. Original is detected. Cover is open. Cover is open. See Remarks. * 1 1 1 1 1
Remarks
Z
Y X C
Platen
B A
Front Side
See Remarks.
iADF Signal 1 = 1 Signal 2 = 1 ADF Signal 1 = 1 Signal 2 = 0 A different signal pattern, indicates that the unit is not connected. 1 1 1 1
031 ADF Original Sensor ADF Original Width Sensor ADF Original Width Sensor ADF Original Length Sensor 2 ADF Original Length Sensor 1
Original is detected. Original is detected. Original is detected. Original is detected. Original is detected. 1
148
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
2. Check Output Press the "START" key to start, and press the "STOP" key to reset. F4 Mode (Output Check) Function When SPC PCB CN715-8 signal level changes to 0V from +24V, count up the Total Counter.
Remark
When SPC PCB CN723-2 signal level changes to 0V from +5V, the Main Motor activates. When SPC PCB CN720-16 signal level changes to 0V from +24V, the Motor rotates in the forward direction. When SPC PCB CN720-18 signal level changes to 0V from +24V, the Clutch activates. When SPC PCB CN704-9,10, CN709-16 are 24V, Power Supply Fan rotates high-speed.
054- Not Used 055 056 Fuser Fan 057- Not Used 060 061 Registration Clutch
When SPC PCB CN715-2 signal level changes to 0V from +24V, clutch operates. When SPC PCB CN715-4 signal level changes to 0V from +24V, clutch operates. When SPC PCB CN706-2 signal level changes to 0V from +24V, motor rotates in the ascending direction. When SPC PCB CN728-2 signal level changes to 0V from +24V, solenoid operates.
1 minute
062 Not Used 063 Paper Feed Roller Clutch (1st Paper Tray) 064 Lift Motor (1st Paper Tray)
1 minute
1 minute
066- Not Used 069 070 Paper Feed Roller Clutch (2nd Paper Tray) 071 Lift Motor (2nd Paper Tray)
When CST2 PCB CN773-2 signal level changes to 0V from +24V, clutch operates. When CST2 PCB CN774-2 signal level changes to 0V from +24V, motor rotates in the ascending direction.
1 minute
149
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
No. Item 072 Intermediate Roller Clutch (2nd Paper Tray) 073- Not Used 074 075 Paper Feed Motor (3rd Paper Tray) 076 Paper Feed Roller Clutch (3rd Paper Tray) 077 Lift Motor (3rd Paper Tray)
F4 Mode (Output Check) Function When CST2 PCB CN773-4 signal level changes to 0V from +24V, clutch operates.
Remark 1 minute
078 Intermediate Roller Clutch (3rd Paper Tray) 079 Not Used 080 Paper Feed Roller Clutch (4th Paper Tray) 081 Lift Motor (4th Paper Tray)
When CST3 PCB CN805-4 signal level changes to 0V from +5V, activate the Motor. When CST3 PCB CN806-2 signal level changes to 0V from +24V, clutch operates. When CST3 PCB CN804-2 signal level changes to 0V from +24V, motor rotates in the ascending direction. When CST3 PCB CN806-4 signal level changes to 0V from +24V, clutch operates. When CST2 PCB CN773-2 signal level changes to 0V from +24V, clutch operates. When CST2 PCB CN774-2 signal level changes to 0V from +24V, motor rotates in the ascending direction. When CST2 PCB CN773-4 signal level changes to 0V from +24V, clutch operates.
1 minute
1 minute
1 minute
082 Intermediate Roller Clutch (4th Paper Tray) 083- Not Used 084 085 Paper Feed Roller Solenoid (Sheet Bypass) 086- Not Used 119 120 Lamp
1 minute
When SPC PCB CN715-6 signal level changes to 0V from +24V, solenoid operates.
1 minute
When SPC PCB CN656-3 signal level changes to +5V from 0V, Lamp operates.
121- Not Used 159 160 ADF Paper Feed Motor Rotating (35% speed rotating) 161 ADF Paper Feed Motor Rotating (100% speed rotating) 162 ADF Paper Feed Motor Rotating (200% speed rotating) 163 ADF Paper Feed Motor Reverse Rotating (35% speed rotating)
ADF paper feed motor rotates at 35% speed. ADF paper feed motor rotates at 100% speed. ADF paper feed motor rotates at 200% speed. ADF paper feed motor rotates in reverse at 35% speed.
150
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
No. 164
165
166
167
168
169
F4 Mode (Output Check) Item Function ADF Paper Feed Motor Reverse ADF paper feed motor rotates in Rotating reverse at 100% speed. (100% speed rotating) ADF Paper Feed Motor Reverse ADF paper feed motor rotates in Rotating reverse at 200% speed. (200% speed rotating) ADF Paper Feed Roller Clutch 1 When ADF PCB CN22-10 signal level changes to 0V from +24V, clutch operates for 3 seconds. ADF Paper Feed Roller Clutch 2 When ADF PCB CN22-8 signal level changes to 0V from +24V, clutch operates for 3 seconds. ADF Paper Feed Roller Clutch 3 When ADF PCB CN24-2 signal level changes to 0V from +24V, clutch operates for 3 seconds. ADF Paper Exit Solenoid When ADF PCB CN26-2 signal level changes to 0V from +24V, Solenoid operates for 3 second. Not Used When ADF PCB CN26-5 signal level changes to 0V from +24V, Solenoid operates for 1 second. When ADF PCB CN26-3 signal level changes to 0V from +24V, Solenoid operates for 1 second. When ADF PCB CN26-7 signal level changes to 0V from +24V, Solenoid operates for 1 second. When ADF PCB CN25-2 signal level changes to 0V from +24V, Solenoid operates for 1 second.
Remark
151
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.1.4.
Set the machine to Service Mode, and press "5" key on the Keypad. Press the "START" key. Enter the desired code number, or press V, /\ arrow keys. If you wish to select another code number, scroll the menu with the arrow keys. Press the "SET" key. Enter the desired function code number, and press SET key. When the CLEAR key is pressed, the selected code input will not be accepted. Press STOP key, then press FUNCTION, and CLEAR keys simultaneously to exit the service mode. Reboot the machine after setting the parameter(s) to activate the setting(s). F5 Mode Function 0 : Auto 1 : 50 Hz 2 : 60Hz 0 : Low 1 : Full 1 : 5 sec. 2 : 10 sec. 3 : 15 sec. 4 : 20 sec. 6 : 30 sec. 8 : 40 sec. 10 : 50 sec. 12 : 60 sec. 0 : No 1 : Yes 0 : Off 1 : Auto 0 : None 1 : Accumulate 2 : Job 0 : Off 1 : On 0 : Off 1 : User (Displays Replace Drum) 2 : Service (Enables Check & Call function) 152
Ver. 1.0 OCT 2006
No. 00 01
02 03 04
05 06
07-08 Not Used 09 Fuser Lamp Control 10 Exit Tray Limitation (Up to 250 Sheets) Replace Drum Replace Drum (Except USA / Canada)
11
0 0
DP-8020E/8020P/8016P
No. 12
F5 Mode Function 0 : Non 2 : 2 min 5 : 5 min 0 : On 1 : Off 0 : None 1 : A3 2 : B4 3 : A4 4 : A4-R 5 : B5 6 : B5-R 7 : A5 8 : A5-R 9 : 8 x 13 10 : 8.5 x 13 11 : LEDGER 12 : LEGAL 13 : LETTER 14 : LETTER-R 15 : INVOICE Same as F5-14 Same as F5-14 Same as F5-14 0 : No 1 : Yes 0 : No 1 : Auto 0 : No 1 : Auto 0 : No 1 : Auto 0 : No 1 : Auto 0 : No 1 : Yes 0 : No 1 : Mid 2 : Large 0 : No 1 : 1 to 2 2 : 2 to 2 3 : B to 2 5
Default Setting
13 14
15 16 17 18 19 20 21 22
Paper Size Tray 2 Paper Size Tray 3 Paper Size Tray 4 Not Used T Corona Current Auto Adj. ADF Not Used System Console
1 (for DP-8020E/8020P) 1
23-25 Not Used 26 2-Sided Unit 27-30 Not Used 31 ADF Duplex Scanning 32 33 Job Build, and SADF Mode TH Sensor (Laser duty)
1 0 1
39
Not Used
153
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
No. 40
F5 Mode Function 0 : No 1 : LDR 2 : LDR, LGL 3 : A3 4 : A3, B4 0 : At feed 1 : At exit 0 : No 1 : Key Cntr 2 : DEPT. 3 : Card Same as F5-41 0 : Yes 1 : No 0 : No 1 : Mid 2 : Large 0 : No 1 : Mid 2 : Large 0 : No 1 : Yes 0 : No 1 : Yes 0 : No 1 : Yes 0 : No 1 : Auto sft 0 : No 1 : Yes 0 : 5 mm 1 : 10 mm 2 : 15 mm 3 : 20 mm 0 : 5 mm 1 : 10 mm 2 : 15 mm 3 : 20 mm 0 : 15 mm 1 : 20 mm 2 : 25 mm 3 : 30 mm 0 : Continue 1 : Any Keys 0 : Stop 1 : Continue
41 42
1 0
43 44 45 46 47
Key Counter Timing Not Used Dept Code Reentry Again Not Used TH Sensor (T corona current)
0 0
48
TH Sensor (DEV)
49 50 51 52 53 54 55
Not Used Auto Contrast Adjust Dept. Counter (COPY) Dept. Counter (FAX) 2-Sided Auto Shift Margin Reduction Margin Value Default
1 1 0 0 0 1
56
57
58 59
1 0
154
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
No. 60 61 62 63 64 65
Item Auto Tray Selection TDC Auto Adj. (DEV Conditions) TDC Auto Adj.(DEV life) U13 Clear Dept. Counter (SCANNER) Dept. Counter (PRINTER)
F5 Mode Function 0 : No 1 : Yes 0 : No 1 : Yes 0 : No 1 : Yes 0 : Any keys 1 : Func + 1 0 : No 1 : Yes 0 : No 1 : Yes 0 : No 1 : Yes 0 : No 1 : 1.5 K 2 : 2.5 K 3: 5K 4 : 10 K 5 : 15 K 6 : 20 K 7 : 30 K 8 : 40 K 9 : 60 K 10 : 80 K 11 : 90 K 12 : 120 K 13 : 150 K 14 : 200 K 15 : 240 K 0 : Unlimited 1 : 1/3 Limited 2 : 2/3 Limited 0 : No 1 : Yes 0 : No 1 : Yes 0 : No 1 : Yes 1 1 0 0 1 1
Default Setting
0 12
71
72-75 Not Used 76 TH Sensor (Corona, Grid) 77 78 79 TH Sensor (Bias DC) A4/LTR Size Select Not Used
1 1 0
155
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
No. 80
F5 Mode Function 1 : A3 2 : B4 3 : A4 4 : A4-R 5 : B5 6 : B5-R 7 : A5 8 : A5-R 9 : 8 x 13 10 : 8.5 x 13 11 : LEDGER 12 : LEGAL 13 : LETTER 14 : LETTER-R 15 : INVOICE 0 : B4 1 : 8 x 13 2 : 8.5 x 13 0 : Off 1 : M1, On 2 : M2, On 3 : M1, M2, On 0 : No 1 : Normal 2 : Quality 0:S>C>B 1:C>S>B 0 : None 1 : Yes 0 : No 1 : 40 K 2 : 60 K 3 : 120 K 4 : 240 K 5 : 360 K 6 : 480 K 7 : 600 K 0 : No 1 : 40 K 2 : 60 K 3 : 120 K 4 : 240 K 5 : 360 K 6 : 480 K 7 : 600 K 0 : Off 1 : Once 2 : ON
81
82
83
84 85 86
1 0 0
87
PM Cycle (ADF)
88
156
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
No. 89
90
91 92 93 94 95 96 97 98
M1, Size Y M1, Size X M2, Size Y M2, Size X Paper Size (FA) Bypass Detection (FA) BP Tray B4/FLS/LGL (FA) TH Sensor (Laser Power)
F5 Mode Function 0 : Auto 1 : 10 Half 2 : 10 Full 3 : 100 Half 4 : 100 Full 0 : Off 1 : Soft 2 : Loud Set the default size for Manual Skyshot Mode, M1, and M2.
Default Setting 0
0 : No 1 : Mid 2 : Large
160 70 220 95 1 (for USA / Canada) 2 (for Europe) 1 (for USA / Canada) 2 (for Europe) 0 (for Europe) 3 (for USA / Canada) 1
99
Not Used
157
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.1.5.
Set the machine to Service Mode, and press "6" key on the Keypad. Press the "START" key. Enter the desired code number, or press V, /\ arrow keys. If you wish to select another code number, scroll the menu with the arrow keys. Press the "SET" key. Enter the desired function code number, and press SET key. When the CLEAR key is pressed, the selected code input will not be accepted. Press STOP key, then press FUNCTION, and CLEAR keys simultaneously to exit the service mode. Reboot the machine after setting the parameter(s) to activate the setting(s). Note: The Factory Setting is different in each model. F6 Mode No. 00 01 02 03 04 05 06 07 08 09 10 11 12 13 Item Adj 100% Side-Side Read Adj 100% Lead-Tail Read 100% Selection Original Registration Printer Registration Main Motor Speed Polygon Motor Speed Registration Void Trail Edge Read Timing Trail Edge Print Timing Side Adjust (Bypass) Side Adjust (Tray 1) Side Adjust (Tray 2) Side Adjust (Tray 3) Setting Range Adjustment for identical vertical (side-to-side) -9 - +9 0.1% size ratio. Adjustment for identical horizontal -9 - +9 0.1% (top-to-bottom) size ratio. Adjustment from 99.1% to 100.9% -9 - +9 0.1% Adjustment of platen original registration -30 - +30 detection timing. 0.2mm Delay time is adjusted from registration roller -50 - +50 clutch ON. 0.5mm Adjustment of Main Motor speed. -10 - +10 0.1% Adjustment Polygon Motor speed. -5 - +5 0.1% Registration void should be adjusted. 0 - +99 0.5mm Adjustment of trail edge void. -9 - 0 0.5mm Adjustment of trail edge void. -9 - +15 0.5mm Adjustment of LSU side-side (Sheet Bypass). -8 - +7 0.5mm Adjustment of LSU side-side (1st Tray). -8 - +7 0.5mm Adjustment of LSU side-side (2nd Tray). -8 - +7 0.5mm Adjustment of LSU side-side (3rd Tray). -8 - +7 0.5mm Remarks
158
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
F6 Mode No. 14 15 16 17 18 19 20 21 22 23 Item Side Adjust (Tray 4) Not Used Side Adjust (ADU) Standard Grid Voltage Standard Laser Power Std Bias DC Voltage Not Used TDC Gain Voltage DC Bias ON timing DC Bias OFF timing Remarks Adjustment of LSU side-side (4th Tray). Setting Range -8 - +7 0.5mm -8 - +7 0.5mm -128 - +19 2.0V -19 - +38 0.05mW -128- +48 2.6V -70 - +57 0.033V -10 - +10 0.01Sec. -10 - +10 0.01Sec. -26 - +26 0.02V -127 - +127 -15 - +15 0.833C -15 - +15 0.833C -99 - +99 (Read only) -99 - +99 (Read only) -99 - +99 (Read only) -99 - +99 -1 - +5 60Sec. -32 - +32 -62 - +110 0.15uA -99 - +99 -99 - +99 -99 - +99 -99 - +99
Adjustment of LSU side-side (ADU). Charge voltage compensation adjustment. Laser power compensation adjustment. Adjustment of bias standard voltage.
Adjustment of toner density sensor gain voltage. (Factory use only) (Factory use only)
24-25 Not Used 26 TDC Judgment Level 27-29 Not Used 30 Light Halftone Adj. 31 Fuser Temperature 32 33 34 35 36 37 38 39 40 41 42 43 44 Fuser Edge Temperature TDC Max. Read Only TDC Min. Read Only TDC Avg. Read Only Paper Loop (Tray 1) Not Used F8-09 (TDC) Adjustment time LSU Unit PWM Adjust Transfer Current Side 1 Paper Loop (Bypass) Paper Loop (Tray 2) Paper Loop (2-Sided) FAX Laser Duty Adj
Adjustment of toner supply starting judgement voltage level. Halftone duty ratio adjustment Adjustment of fuser temperature. Temperature compensation for edges Set by F8-20 TDC Check Operation Set by F8-20 TDC Check Operation Set by F8-20 TDC Check Operation Individual Fine Adjustment for Tray 1 (Factory use only) Adjustment of PWM value of LSU. Adjustment of Transfer Current. Individual Fine Adjustment for Sheet Bypass Individual Fine Adjustment for Tray 2 Adjustment for the length of the loop formed before the copier timing roller. Printer Density Adjustment for FAX. (-) : Darker. (+) : Lighter.
45
Ver. 1.0
OCT 2006
DP-8020E/8020P/8016P
F6 Mode No. 46 Item PRINTER Laser Duty Adj Remarks Printer Density Adjustment for Printer. (-) : Darker. (+) : Lighter. Adjustment of Transfer Current. Adjustment of Transfer Current. Image density adjustment for Text mode. (-) : Darker. (+) : Lighter. Image density adjustment for Text/ Photo mode. (-) : Darker. (+) : Lighter. Image density adjustment for Photo mode. (-) : Darker. (+) : Lighter. Adjustment of CCD read position. Adjustment of Contrast for Text Mode. Adjustment of Contrast for Text/Photo Mode. Adjustment of Contrast for Photo Mode. Adjustment of Corona Charge Current. Trail Edge Transfer Image High Voltage Timing Adjustment for Trays 1-4 feeding. Trail Edge Transfer Image High Voltage Timing Adjustment for Bypass Tray feeding. Trail Edge Transfer Image High Voltage Timing Adjustment for the 2nd side of 2-Sided printing. Adjustment of Toner Density sensor gain voltage. Adjustment of Lead Edge Read Point. Setting Range -99 - +99
47 48 49
50
-99 - +99
51
-99 - +99
52 53 54 55 56 57 58 59 60 61
Not Used CCD Read Position Adj T Mode Contrast T/P Mode Contrast P Mode Contrast Not Used Corona Charger Current Trail Edge Trans (Trays) Trail Edge Trans (Bypass) Trail Edge Trans (2Sided)
-42 - +44 0.2mm -128 - +127 -128 - +127 -128 - +127 -77 - +76 1.3uA -30 - +30 0.5mm -30 - +30 0.5mm -30 - +30 0.5mm -10 - +10 0.033V 0 - +9 0.5mm
62 63
TDC Gain Voltage Adjust Lead Edge Read Timing (Adjustment for Double Exposure Copy Mode, for details, and adjustment procedure, refer to Sect. 2.9.8) Side Edge Read Adjust (Adjustment for Double Exposure Copy Mode, for details, and adjustment procedure, refer to Sect. 2.9.8) Transfer Current Side 1 (Small Width) Transfer Current Side 2 (Small Width)
64
0 - +9 0.5mm
65 66
160
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
F6 Mode No. 67 68 69 70 71 Item ADF Image Density Paper Loop (Tray 3) Stamp Position Adjust Remarks Compensation of ADF image density. Individual Fine Adjustment for Tray 3 Adjustment of verification stamp position. Setting Range -99 - +99 -99 - +99 -50 - +50 0.3mm -99 - +99 0.05mm -99 - +99 0.3mm -127 - +127 0.3mm -50 - +50 0.3mm
Not Used ADF Read Main Scan Pos. (Reverse Side) 72 Original Lead Edge ADF (Reverse Side) 73 Original Trail Edge ADF (Reverse Side) 74 Stamp Position Adjust (Reverse Side) 75-76 Not Used 77 Add Toner Level 78 79 80 81 82 83 84 85 86 87 Paper Loop (Tray 4) MTF Adjust Laser Power Control Grid voltage Control Bias DC Voltage Control Temperature Sensor Value Humidity Sensor Value Not Used ADF Reverse Stop Posi. ADF Exhaust Stop Posi.
Adjustment of ADF horizontal image read start position. Adjustment of ADF Original Lead Edge Adjustment of ADF Original Trail Edge Adjustment of Stamp Position
-1 - +1 1 Individual Fine Adjustment for Tray 4 -99 - +99 Adjustment of Scanning Sharpness by digital -2 - +2 image processing for Text /Photo Copy Mode. 1 -99 - +99 (Read Only) -99 - +99 (Factory use only) (Read Only) -99 - +99 (Read Only) Value of Temperature sensor. 0 - 255 (Read Only) Value of Humidity sensor. 0 - 255 (Read Only) Adjustment of ADF reverse stop position. -99 - +99 0.3mm -99 - +99 0.3mm -99 - +99 0.05mm -99 - +99 0.3mm -127 - 127 0.3mm -9 - +9 0.1% -9 - +9 0.1%
88-89 Not Used 90 ADF Image Read Start 91 92 93 94 Original Lead Edge ADF Original Trail Edge ADF ADF 100% Image 1-Sided ADF 100% Image 2-Sided
Adjustment of ADF horizontal image read start position. Adjustment of original detection timing. Adjustment of trail edge detection timing. Adjustment of magnification for 1-sided. Adjustment of magnification for 2-sided.
DP-8020E/8020P/8016P
F6 Mode No. 99 Item F5/F6 Initialization Remarks Initialize F5/F6 parameter settings. Setting Range
162
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.1.6.
Set the machine to Service Mode, and press "7" key on the Keypad. Press the "START" key. Enter the desired code number, or press V, /\ arrow keys. If you wish to select another code number, scroll the menu with the arrow keys. Press the "SET" key. Enter the desired function code number, and press SET key. When the CLEAR key is pressed, the selected code input will not be accepted. Press STOP key, then press FUNCTION, and CLEAR keys simultaneously to exit the service mode. Reboot the machine after setting the parameter(s) to activate the setting(s). F7 Mode No. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Item Key Operator ID Code Total Count PM Count Scanner PM Count Not Used OPC Drum Count Process Unit Count ADF PM Count Not Used Developer Count Sheet Bypass Count 1st Paper Tray Count 2nd Paper Tray Count 3rd Paper Tray Count 4th Paper Tray Count 2-sided Count ADF Count ADF Read Count Scanner Count Scanner Read Count Copy Print Count Copy Scan Count PC Print Count PC Scan Count Remarks Key Operators identification code for access to the counter mode. Total count for all copies / prints. Preventive Maintenance count. PM count for scanner readings. PM count of recording paper fed through the OPC Drum. PM count of recording paper fed through the Process Unit. PM count of originals fed through the ADF. PM count of recording paper fed through the Developer. Total count of paper fed from the sheet bypass. Total count of paper fed from the 1st paper tray. Total count of paper fed from the 2nd paper tray. Total count of paper fed from the 3rd paper tray. Total count of paper fed from the 4th paper tray. Total count of 2-sided Print. Total count of originals fed through the ADF. Total count of originals scanned through the ADF. Total count of scanning operations. Total count of scanner readings. Total count of copies printed. Total count of copies scanned. Total count printed from PC. Total count scanned to PC. 163
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
F7 Mode No. 25 26 27 28 29 30 31 32 99 Item Fax Transmit Count Fax Receive Count Fax Print Count Total OPC Rotation Time A4/LT Count A4R / LETTER R Count A3 / Ledger Count B4 / LEGAL Count All Counter Clear Remarks Total count of Fax transmitted. Total count of Fax received. Total count of Fax printed. Total Time of OPC Rotation. Total count of A4 / Letter Print. Total count of A4-R / Letter-R Print. Total count of A3 / Ledger Print. Total count of B4 / Legal Print. All counters are cleared.
164
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.1.7.
Set the machine to Service Mode, and press "8" key on the Keypad. Press the "START" key. Enter the desired code number, or press V, /\ arrow keys. If you wish to select another code number, scroll the menu with the arrow keys. Press the "SET" key. Enter the desired function code number, and press SET key. When the CLEAR key is pressed, the selected code input will not be accepted. Press STOP key, then press FUNCTION, and CLEAR keys simultaneously to exit the service mode. Reboot the machine after setting the parameter(s) to activate the setting(s). F8 Mode No. 00 Item Exp. Lamp Replacement Remarks When replacing the exposure lamp. Procedure: a) Press the Start key to move the exposure lamp to the position (approx. 250 mm from the optics home position) where it can be replaced. b) To return the optical system to the home position, press the CLEAR key.* a) Each time the arrow key is pressed, the machine errors, or paper jam codes stored in memory are displayed, beginning with the oldest code. Note: Only the 30 most recent codes are displayed. a) Press the Reset key. A Message "Error code can be cleared with the Start key" is displayed on the LCD.* b) Press the Start key. Lock operation for Scanner Unit. Adjustment operation of Toner Density. Adjustment operation of Drum Charge. Adjust the slice level for the original size detection sensors automatically. Execute this mode by closing the platen cover. Adjustment operation of Black Density sensor. Proceed when OPC is replaced. Print out the Test Pattern. Proceed when the LSU is replaced. 165
Ver. 1.0 OCT 2006
07
08 09 10 11 12
(Factory use only) Toner Density Adjustment Drum Charge Adjustment Not Used Org.size Sensor Adj. (Not Used)
Black Density Reference (Not Used) 14 OPC Counter Reset 15-17 Not Used 18 LSU PWM Pattern
13
DP-8020E/8020P/8016P
F8 Mode No. 19 Item Move Mirror To Lock Remarks a) Press the Start key to move the mirror unit to the locked position for transporting the copier. b) When the mirror unit is locked, the machine will not accept any numerical key input. Note: The locking operation is automatically reset when the Power switch is turned ON again. Adjustment of TDC sensor. Press START key to begin. Press START key to begin.
20 21-46 47 48
TDC Check Operation Not Used ADF Continuous Test Platen Continuous Test
166
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.1.8.
Set the machine to Service Mode, and press "9" key on the Keypad. Press the "START" key. Enter the desired code number, or press V, /\ arrow keys. If you wish to select another code number, scroll the menu with the arrow keys. Press the "SET" key. Enter the desired function code number, and press SET key. When the CLEAR key is pressed, the selected code input will not be accepted. Press STOP key, then press FUNCTION, and CLEAR keys simultaneously to exit the service mode. Reboot the machine after setting the parameter(s) to activate the setting(s). F9 Mode Service Item Mode F9 Unit 00 Fax Service Mode Maintenance 01 Service Alert Tel # 02 Firmware Version 00 SC 01 SC Boot 02 03 04 05 PNL SPC Not Used FAX Modem Remarks Displays the contact number when a machine malfunction occurs. Displays the firmware version for SC. Displays the firmware version for SC Boot. Displays the firmware version for PNL. Displays the firmware version for SPC. Displays the firmware version for FAX option 1.
Displays the firmware version for Slot 1. Prints the memory contents of the F5, 03 Print Device Info. and F6 modes. 01 Machine Information Prints the machine setup information list. 02 Counter Information Prints the Counter information list. 03 System Address Prints the system memory setting. Info. 04 RAM Address Prints the RAM data dump list. Information 04 RAM Edit 0 Relative Address Setting of Relative address. Mode 1 Absolute Address Setting of Real address. 05 Serial Number Registration of Serial Number for Maintenance. Clears by Shipment Set.
167
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
F9 Mode Service Item Mode F9 Unit 06 RAM 00 Parameter Initialize Maintenance Initialize Remarks Resets the Fax, and Function parameters to default values. Note: Turn the Power Switch to the OFF, and back to the ON position to enable the parameter settings. Clears all Jobs stored in Flash Memory. Clears LBP Error log Clears All Jobs, All Preset Data, Parameter Initialize & Resets the Counters (Fax). Clears the LBP fuser error. Resets the Counter Clears the Flash Memory Data Updates the firmware in the machine with the Master Firmware Card. Updates the firmware in the machine with the USB. Onboard F-ROM 4MB Slot 1 FRM8 PCB 8MB Slot 1 FRM8 PCB 4MB (a) Slot 1 FRM8 PCB 4MB (b) Slot 2 FRM8 PCB 8MB Slot 2 FRM8 PCB 4MB (a) Slot 2 FRM8 PCB 4MB (b) Creates a Master Firmware Card using the Firmware Update Kit. A 4MB, or 8MB Flash Memory Card will be required depending upon the model. Configuration for Program copy.
07 Firmware Update
04 05 06 00
LBP Fuser Reset Dept. Counter Clear Flash Memory Clear Update FROM Card
01 Update from USB 08 Program Backup (Refer to Sect. 2.7.) 00 Main 01 Option 1 all 02 Option 1 a 03 Option 1 b 04 Not Used 05 Not Used 06 Not Used 09 Update Program Card
10 Program Copy
11 12 13 14
00 From card to slot 1 01 Not Used 02 From slot 1 to card 03 Not Used 04 Not Used 05 Not Used Parameter Backup Parameter Restore Page Memory Size Sort Memory Size
Backup the Parameter. Restore the Parameter. Displays the page memory size (MB). Displays the sort memory size (MB).
168
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.
Caution: The factory default parameters are preset (destination dependent) for optimum performance, and in compliance with the local telecommunication regulations/standards, and do not need to be changed. Changing some of these parameters may cause the unit to be no longer compliant, or become inoperable.
4.2.1.
1. To enter the Fax Service Mode a. Press FAX/EMAIL key. b. Press FUNCTION, and then 7 keys. c. Press MONITOR four times, then press *. d. Enter the desired code number, or press the V, /\ arrow keys. 2. To exit the Fax Service Mode Press STOP key. Note: The following buttons provide these functions in the Service Mode: "START": "V "/\ : : : The new setting value is stored in the machine. Scroll the function parameter number down. Scroll the function parameter number up.
4.2.2.
The following service modes are provided to assist you in setting operational functions of the unit, and determining the condition of the unit. Service Modes (For Facsimile) Description Allows changes to the function parameters (the home position, etc.). (Factory use only) Prints the Function Parameter List, Page Memory Test, Printer Report, All Document File, Protocol Trace, and Toner Order Form. Generates various binary, tonal, and DTMF signals, by the modem. Initialize RAM, and restore the default value of the function parameters. Note: Turn the Power Switch to the OFF, and back to the ON position to enable the parameter settings. Allows input of information for Service Alert Report, Maintenance Alert Report, and Toner Order Form. Used for Firmware Update, Firmware Backup, Parameter Restore, Parameter Backup, Transferring Firmware from the PC to the Flash Card, and Sending a Received File during a fatal printer error. 169
Ver. 1.0 OCT 2006
No. Service Mode 00 Not Used 01 Function Parameter Setting 02 03 RAM Edit Mode Print Parameter List / Report
04 05 06
07 08 09
DP-8020E/8020P/8016P
4.2.3.
Use the following procedure to change the function parameters. Enter the desired code number, and press START key. If you wish to select another code number, scroll the menu with the V, /\ arrow keys. Select the desired function code, and press the "START" key. When the CLEAR key is pressed, the selected code input will not be accepted. Press STOP key twice to exit the service mode. Function Parameter Table Selections Function 1 = Monitor Selects whether the machine starts to TX automatically during On-Hook dialing. 2 = Tel/Dial Monitor : Start to TX after pressing START TEL/DIAL : Start to TX automatically 1 = Off Selects the No Paper, or No Toner alarm status. 2 = Timer OFF : Alarm is disabled. 3 = Constant Timer : Alarm will shut off after 6 seconds. Constant : Alarm will not stop until "STOP" is pressed, or the error is cleared/ corrected. 1 = Off Selects whether the machine prompts to print the 2 = On COMM. Journal when the printout condition is set to INC, and STOP is pressed during communication. 1 = Off Selects whether the Continuous Polling feature is 2 = Stn (Tx only) enabled. 3 = Hub (Rx only) Stn : Place the document(s) on the ADF, or Platen, then press the assigned Program Key to store, or add the documents into a polled file. (See Note 1) Hub : When the polling command is initiated, the machine will continuously poll originals from the remote stations until it is interrupted by pressing "STOP". 1 = Off (will not accept) Selects whether the machine accepts, and allows to 2 = On (accepts) set, or change the Numeric ID.
170
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
No. 005
009 010
011
Function Parameter Table Parameter Selections Function Destination Code 000 : Austria Specified destinations only. 001 : U.K. 002 : Canada 003 : Denmark 004 : Taiwan 005 : Finland 006 : Germany 007 : Netherlands 008 : Italy 009 : Spanish 010 : Hong Kong 011 : Australia 012 : Switzerland 013 : Norway 015 : Portuguese 016 : Ireland 017 : Belgium 018 : Sweden 019 : Turkey 020 : U.S.A. 021 : France 022 : New Zealand 025 : Japan 029 : Poland 030 : Czech 031 : Russia 032 : Greece 033 : Hungary 034 : Indonesia 035 : South Korea 038 : Malaysia 039 : China 045 : Thailand 048 : South Africa 049 : Singapore 050 : Universal 051 : East Euro ID Display 1 = Number (Numeric ID) Selects the priority of displaying the ID. 2 = Chara (Character ID) JRNL Column 1 = Station Selects the contents of the ID to display on the 2 = RCVD ID Journal. Monitor 1 = Off Selects whether the Monitor is ON/OFF for 2 = On monitoring fax signals. (FOR SERVICE USE ONLY) DC Loop 1 = Off (Normal) Selects a false Off Hook state for back to back 2 = On (Off Hook) communication test. TX Level 00 = 0 dBm Selects the TX signal output level, 0 to -15 dBm in 1 ~ dBm steps. (Refer to Chapter 4.3.of the Service 15 = -15 dBm Manual) RX Level 1 = -43 dBm Selects the receiving sensitivity of -33/-38/-43/-48 2 = -38 dBm dBm. 3 = -33 dBm 4 = -48 dBm 171
Ver. 1.0
OCT 2006
DP-8020E/8020P/8016P
013 G3 RX EQL
014 G3 TX EQL
Function Parameter Table Selections Function 00 = 0 dBm Selects the DTMF output level, 0 to -15 dBm in 1 ~ dBm steps. 15 = -15 dBm 1 = 0dB Selects the cable equalizer for G3 reception mode, 2 = 4dB 0dB, 4dB, 8dB, or 12dB. 3 = 8dB 4 = 12dB 1 = 0dB Selects the cable equalizer for G3 transmission 2 = 4dB mode, 0dB, 4dB, 8dB, or 12dB. 3 = 8dB 4 = 12dB
2400 bps 4800 bps 7200 bps 9600 bps TC7200 TC9600 12000 bps 14400 bps 2400 bps 4800 bps 7200 bps 9600 bps TC7200 TC9600 12000 bps 14400 bps 1 = Off 2 = On 3 = Select
018 RX Start
Selects the transmission modem start speed, 14400/12000/TC9600/TC7200/9600/7200/4800/ 2400 bps. Press V, or /\ to select the symbol rate. Note: This parameter is applicable only when communicating with regular G3 machines. When communicating with Super G3 (V.34) machines, use Parameter No. 32. Selects the reception modem start speed, 14400/ 12000/TC9600/TC7200/9600/7200/4800/2400 bps. Press V, or /\ to select the symbol rate. Note: This parameter is applicable only when communicating with regular G3 machines. When communicating with Super G3 (V.34) machines, use Parameter No. 33. Selects whether the ITU-T V.34 is Off, On, or Select. Select: Select whether the ITU-T V.34 is Off, or On, when entering Phone Book Dialing Numbers, or Manual Number Dialing. Select the ECM mode. Selects whether to add the echo protect tone on V.29 mode. (Used when Echo Suppression is disabled.) On : Add Off : Do not add Selects the time interval between the receiving signal, and the transmitting signal. Selects the TCF check interval Long/Short Selects the CED frequency 2100/1080 Hz Selects the communication start-up condition (XMT, and Polling). (Used when Echo Suppression is disabled.) 172
1 = 100 ms 2 = 200 ms 3 = 500 ms 1 = Normal (Short) 2 = Long 1 = 1080 Hz (non ITU-T) 2 = 2100 Hz 1 = First 2 = Second
Ver. 1.0
OCT 2006
DP-8020E/8020P/8016P
No. Parameter 026 Non-Standard 027 Short Protocol B 028 Short Protocol D
034 V34 TX SR
035 V34 RX SR
Function Parameter Table Selections Function 1 = Off (Invalid) Selects own mode (Panafax mode). 2 = On (Valid) 1 = Off (Invalid) Selects the short protocol mode. 2 = On (Valid) 1 = Off (Invalid) Selects the short protocol mode. When activated, it 2 = On (Valid) allows the machine to automatically store the modem speed for each Auto Dial Number. 1 = Off (will not accept) Selects whether the machine accepts Remote 2 = On (accepts) Diagnostics from the service station. 1 = 75 ms Selects the pause interval between the CED, and 2 = 1 sec the 300 bps signal. (Used when Echo Suppression is disabled.) 1 = Off (EOLx6) Selects the RTC signal, EOLx6, or EOLx12. 2 = On (EOLx12) 2400-33600bps Selects the transmission modem start speed for V.34 communication, 33600-2400 bps. Press V, or /\ to select the symbol rate. 2400-33600bps Selects the receiving modem start speed for V.34 communication, 33600-2400 bps. Press V, or /\ to select the symbol rate. 2400-3429sr Selects the transmission symbol rate for V.34, 3429/ 3200/3000/2800/2400 sr. Press V, or /\ to select the symbol rate. 2400-3429sr Selects receiving symbol rate for V.34, 3429/3200/ 3000/2800/2400 sr. Press V, or /\ to select the symbol rate. 1 = Off (not displayed) 2 = On (displayed) Selects whether to display the modem speed during communication. (Press the Job Status Key to display) Selects the pause interval before activating the Flash key. Selects the pause interval before activating the Flash key. (For Germany, Austria, and Czech) Selects the pause interval from 1 sec. ~ 10 sec. for dialing through a switchboard, or for international calls. Selects the redial interval from 0 to 15 minutes in 1 minute steps. Selects the redial count from 0 to 15 times in 1 step intervals. Note: In order to comply with the requirements TBR21 in the EC countries, do not select 15 times.
5 = 50 ms ~ 100 = 1000 ms 5 = 50 ms ~ 100 = 1000 ms 1 = 1 sec. ~ 10 = 10 sec. 0 = no waiting ~ 15 = 15 minutes 0 = no redial ~ 15 = 15 times 0 ~ 9 (For Australia Only)
173
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Function Parameter Table Selections Function 1 = 1 ring Selects the ring detection count from 1 to 9 rings in ~ 1 ring step intervals. 9 = 9 rings 0 = 0 sec. Selects the on-hook time between sequential ~ communication calls in 1 second step intervals. 90 = 90 sec. 1 = 1 sec. Selects the waiting interval for the response after ~ completing the dialing. 90 = 90 sec. 20 ~ 150 sec. (For France Only)
048~ Not Used 049 050 Ring Detect Mode 1 = Normal 2 = Rough 051 Not Used 052 Pulse Rate
Selects the quality of ringer detection. Use if the line signal is out of regulation, set to "Rough" so that the unit may detect the ringing signals. Selects the dial pulse rate 10/20 pps.
1 = 10 pps 2 = 20 pps
053~ Not Used 054 055 Busy Tone Check 1 = Off 2 = On 056 Dial Tone Check 1 = Off 2 = On 057 DC Loop Check 1 = Off (Except for USA, 2 = On and Canada) 1 = Off (without image) 058 Comm. JRNL + Image 2 = On (with image) 059 Confidential RCV 1 = Off (does not print out) Report 2 = On (prints out) 060 Version Indicates the Host software version. 061 TX/RX/PRT/CPY TX:****** PRT:****** RX:****** CPY:****** 062 Print Counter 1 = Off 2 = On 063~ Not Used 067 068 NYSE Fax Forward (USA, and Canada Only)
Selects whether to detect the Busy Tone. Selects whether to detect Dial Tone before dialing the telephone number. Selects whether the unit checks the DC Loop during communication. Selects whether the machine prints the COMM. Journal with image. Selects whether the machine prints the Confidential RCV Report.
Displays the transmitted, received, total printed, and copied document count. Selects whether to print in the Fax Parameter List, the counter information that is displayed in the Function Parameter No. 61.
1 = Off 2 = On
Selects whether the machine will forward the incoming, and outgoing faxes to a specified station. Note: Once this parameter is activated, Fax Forwarding via Fax Parameter No. 054 is automatically disabled, an Access Code of "0000" is automatically assigned, and Fax Parameter No. 038 has a new setting added called "NYSE". 174
Ver. 1.0
OCT 2006
DP-8020E/8020P/8016P
Function Parameter Table No. Parameter Selections Function 069 NYSE Local Print 1 = Inc Selects the printing condition for the incoming faxes (USA, and 2 = On (Always) after FAX Forwarding. Canada Only) INC. : Prints only if FAX Forwarding fails. ON : Always prints. 070 Line Error 128 lines 1. Selects the line disconnect condition during 256 lines reception. If the number of line errors exceed this 512 lines setting, the unit will disconnect the line. 1024 line Press V, or /\ to select the symbol rate. 2048 lines 2. Selects the transmit condition of RTP/PIP, or Off (will not disconnect RTN/PIN. line) (Available if No. 73 Error Detect is set to "LINES") (See Note 1) 071 Total Error 1 = 5% Selects the transmit condition of RTP/PIP, or RTN/ 2 = 10% PIN. 3 = 15% (Available if No. 73 Error Detect is set to "RATE".) 4 = 20% (See Note 2) 072 Continuous Error 1 = Off (unlimited) Selects the continuous total error criteria of Off/3/6, 2 = 3 lines/STD or 12 lines in Standard mode. If continuous total 3 = 6 lines/STD error exceeds this setting, the unit will transmit 4 = 12 lines/STD RTN/PIN. (Available if No. 73 Error Detect is set to "RATE".) 073 Error Detect 1 = Lines Selects the error detect condition Lines/Rate. 2 = Rate 074 RTN Receive 1 = Disconnect Selects whether to disconnect the phone line, or 2 = Continue continue when "RTN" is received. 075 Coding 1 = MH (MH only) Selects the coding scheme. 2 = MR (MH, or MR) 3 = MMR (MH, MR, or MMR) 4 = JBIG 076 Batch TX 1 = Off Selects whether the batch transmission is available. 2 = On 077 RX JAM Length 1 = Off (unlimited) Selects the maximum length of a received 2=2m document that can be printed. 078~ Not Used 079 080 Doc Top Feed -99 Adjusts the distance between the scanning sensor ~ ON position, and the scanning start position. +99 081 Doc End Feed -90 Adjusts the distance between the scanning sensor ~ OFF position, and the scanning end position. +127 082 JAM Length 1=1m Selects the maximum length of the original that can 2=2m be scanned. 083 Not Used 084 Line As No Paper 1 = Ring (ring) Selects whether to ring, or send a busy tone to the 2 = Busy (keep line busy) remote station when the recording paper runs out, or the unit cannot receive because of any trouble. 085 Not Used 086 Reduction Fine 1 = Off Selects whether to fix with Fine Mode, or not for the 2 = On Reduction transmission. 175
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
No. 087 088 089 090 ~ 091 092 093 ~ 094 095 096~ 101 102
Parameter Darker Level Normal Level Lighter Level Not Used Smoothing Not Used Reduction Ratio Not Used Original Registration
Function Parameter Table Selections Function 0 = Lightest Contrast Selects the contrast level. ~ 0 15 15 = Darkest Contrast Lightest Darkest
1 = Off 2 = On
(70-100)
103 Trail Edge Read Timing 104~ 109 110 111 112 Not Used
-30 ~ +30 -9 ~ 0
Indicates the MAC Address. Selects whether the Text Template (email message) is programmable, and added on all email sent in the message body above the top line of text. (Up to 40 characters Programmed in the User Parameters.) Note: After enabling this feature, aside from entering the text in the User Parameters, it also has to be activated in each Auto Dial Number before it will take effect. It does not work for Direct Dialed Numbers.
1 = Scroll 2 = Direct
116 Overwrite Warning 117~ Not Used 121 122 LDAP 123 One Ring Sound (USA, and Canada Only)
1 = Yes 2 = No
Selects the setting method for Time Zone. Scroll : Allows using "Scroll Keys" to scroll through the Time Zone Table. Direct : Allows you to input the Time Zone directly, (*) key to be used as a switch between +/-. Selects whether the Overwrite Warning is included on the Internet FAX Result Receipt when programming the Auto Dialer via email.
1 = Off 2 = On 1 = Off 2 = On
When LDAP is used, specialized characters may be displayed as different characters. When Function Parameter No. 45 "Ring Detect Count" is set to 1 Ring, and this parameter is enabled (On), the machine will only ring once out loud, answering on the second ring count. 176
Ver. 1.0
OCT 2006
DP-8020E/8020P/8016P
Function
Note 1: Continuous Polling (Station Mode) This feature allows you to store, or add documents into a polled file in memory. To enable the Continuous Polling feature set Function Parameter No. 003 to "2:Station". The last Program Key will be assigned with the Store 4 Poll Key name automatically and cannot be changed. To prepare the document(s) to be polled, simply place the document(s) on the ADF, or Platen and then press the Program Key to store, or add the document(s) into a polled file. (Note: If a regular polled file is stored in memory, the Program Key for Continuous Polling will not be accepted.) Note 2: Function Parameter No. 070 (Line Error)-Transmit condition of RTP/PIP, or RTN/PIN Signal MCF/PIP RTP/PIP RTN/PIN Setting 3:512 4:1024 0-127 0-255 128-255 256-511 256-511 512-1023
6:Off Always -
Note 3: Function Parameter No. 071 (Total Error)-Transmit condition of RTP/PIP, or RTN/PIN Signal MCF/PIP RTP/PIP RTN/PIN Setting 2:10% 3:15% 0-4 0-7 5-9 8-14 1015-
Note 4: The default setting of parameters depends on the countrys specifications, or regulations. Print the Function Parameter List to confirm the default settings.
177
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.4.
From this Service Mode you can print the Function Parameter List, Page Memory Test, Printer Report, All Document File, Protocol Trace, and the Toner Order Form.
4.2.4.1.
A list of all Function Parameters can be printed by the following procedure. Press the V, /\ arrow keys to select the "3: Print Report/List" on the display. Press the SET key to select the "1: Function Parameter List". Press the SET key. Press the STOP key twice to exit the service mode.
178
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
On Off Off On On
14400bps 14400bps On On Off 500ms Normal 2100Hz First On On On On 75ms Off 33600bps 33600bps 3429sr 3429sr Off 500ms
Version ..... AcV........ TX/RX/PRT/CPY 000080/000168/000003/000000 Print Counter Off ---------------------------------------------------------------Line Error Total Error Conti. Error Error Detect RTN Receive Coding BATCH TX:[On] RX JAM Length ------------------Doc Top Feed Doc End Feed JAM Length ---------Line As NoPaper ---------Reduction Fine Darker Level Normal Level Lighter Level ------------------Smoothing ------------------Reducton Ratio ------------------------------------128 10 Off Rate Discon JBIG On 2 m
0 0 2 m Ring On 2 8 4
On
100%
Note: 1. The contents of the Function Parameter List may vary depending on the countrys regulations. 2. * mark will be shown on the left side of number when setting was changed from default.
179
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.4.2.
A test pattern prints out for checking the page memory, and printer mechanism using the following procedure. Press the V, /\ arrow keys to select the "3: Print Report/List" on the display. Press the SET key to select the "1: Function Parameter List". Press the V, /\ arrow keys to select the "3: Page Memory Test". Press the SET key. Press the STOP key twice to exit the service mode.
************* TEST PATTERN PRINT **************** DATE MMM-dd-yyyy ***** TIME 12:07 ***P.01
: : : : : :
180
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.4.3.
Printer Report
All printer errors are logged on the Printer Report which can be printed by the following procedure. Press the V, /\ arrow keys to select the "3: Print Report/List" on the display. Press the SET key to select the "1: Function Parameter List". Press the V, /\ arrow keys to select the "4: Printer Report". Press the SET key. Press the STOP key twice to exit the service mode.
**************-PRINTER REPORT-********************* DATE MMM-dd-yyyy ***** TIME 19:02******** LAST PRINT ERROR SERIAL NUMBER CUSTOMER ID FIRMWARE VERSION SC PNL SPC TRANSMIT COUNTER RECEIVE COUNTER COPY COUNTER PRINT COUNTER : MMM-dd-yyyy 15:38 J00 : : 1234567890123456 : : : : : : : 000475 000398 000083 000016 00-00000016
ERROR CODE RRROR COUNT NO.DATE & TIME ERROR CODE RRROR COUNT | NO.DATE & TIME -------------------------------------------------------------------------------------------01.MMM-dd-yyyy 15:38 J00 00-00000016 | 02.MMM-dd-yyyy 10:48 J02 00-00000016 | --------------------------------------------------------------------------------------------
-*******-12345678901234567890-**************
181
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.4.4.
Print the document files from the Flash Memory. Press the V, /\ arrow keys to select the "3: Print Report/List" on the display. Press the SET key to select the "1: Function Parameter List". Press the V, /\ arrow keys to select the "5: All Document Files". Press the SET key. Press the STOP key twice to exit the service mode.
182
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.4.5.
Protocol Trace
Print a Protocol Trace Report for the previous communication. Press the V, /\ arrow keys to select the "3: Print Report/List" on the display. Press the SET key to select the "1: Function Parameter List". Press the V, /\ arrow keys select the "6: Protocol Trace". Press the SET key. Press the STOP key twice to exit the service mode.
*************** PROTOCOL LOG. REPORT ****************** DATE MMM-dd-yyyy ***** TIME 16:56 *******
: : : : :
COMMAND LOG. REMOTE : NSF CSI DIS CFR LOCAL : TSI DCS PIX PPS-EOP -----------------------------------------------------------------REMOTE : MCF LOCAL : DCN -PANASONIC ****************************-PANASONIC -*************-12345678901234567890-***************
183
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.4.6.
The Toner Order Form can be printed out manually by the following procedure. Press the V, /\ arrow keys to select the "3: Print Report/List" on the display. Press the SET key to select the "1: Function Parameter List". Press the V, /\ arrow keys to select the "7: Toner Order Form". Press the SET key. Press the STOP key twice to exit the service mode.
184
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
**** The toner supply in your machine is running low **** (1) To order a replacement Bottle from your Authorized Dealer
by Phone: by Fax:
Attention: Phone No.: Customer ID: ABC COMPANY (4) Toner Cartridge:
(5)
Serial No.:
Quantity Required:
Explanation of Contents (1) Low Toner Message (Fixed) (2) Toner Order Tel # (3) Toner Order Fax # (4) Customer ID (5) Toner Cartridge The toner supply in your machine is running low Up to 36 digits Up to 36 digits Up to 16 characters (User Identification Code) DQ-TU10J (For DP-8020E/8020P/8016P Except for USA, Canada, and China) DQ-TUJ10K (For DP-8020E/8020P/8016P for USA, Canada, and China)
185
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.5. 4.2.5.1.
This Service Mode is used to check the binary signal output. Signals can be output to the line using the following procedure. Press the V, /\ arrow keys to select the "4: MODEM Test" on the display. Press the SET key to select the "1: Signal Test". Press the SET key. Press the desired number. Press the SET key. Press the STOP key twice to exit the service mode. Binary Signal Table Number 1 2 3 4 5 6 7 8 9 Signals V21 300bps V27ter 2400bps V27ter 4800bps V29 7200bps V29 9600bps V17 TC7200bps V17 TC9600bps V17 12000bps V17 14400bps
186
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.5.2.
Tonal Signal
This Service Mode is used to check the tonal signal output. Signals can be output to the line using the following procedure. Press the V, /\ arrow keys to select the "4: MODEM Test" on the display. Press the SET key to select the "2: Tonal Test". Press the SET key. Press the desired number, and press the "START" key. Press the STOP key twice to exit the service mode. Tonal Signal Table Number 1 2 3 4 5 6 7 Signals 462 Hz 1080 Hz 1100 Hz 1300 Hz 1650 Hz 1850 Hz 2100 Hz
187
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.5.3.
DTMF Signal
This Service Mode is used to check the DTMF (Dual Tone Multi Frequency) signal output. The DTMF signal can be generated using the following procedure. DTMF Single Tone Press the V, /\ arrow keys to select the "4: MODEM Test" on the display. Press the SET key to select the "3: DTMF Test". Press the SET key. Press the V, /\ arrow keys to select the "1. Single". Press the desired number, and press the "START" key. Press the STOP key twice to exit the service mode. DTMF Dual Tone Press the V, /\ arrow keys to select the "4: MODEM Test" on the display. Press the SET key to select the "3: DTMF Test". Press the SET key. Press the V, /\ arrow keys to select the "2. Dual". Press the desired number, and press the "START" key. Press the STOP key twice to exit the service mode. DTMF Single Tone Table Number 1 2 3 4 5 6 7 8 DTMF Signal Tones 697 Hz 770 Hz 852 Hz 941 Hz 1209 Hz 1336 Hz 1477 Hz 1633 Hz DTMF Dual Tone Table Number 0 1 2 3 4 5 6 7 8 9 * # DTMF Dual Tones 941 Hz + 1336 Hz 697 Hz + 1209 Hz 697 Hz + 1336 Hz 697 Hz + 1477 Hz 770 Hz + 1209 Hz 770 Hz + 1336 Hz 770 Hz + 1477 Hz 852 Hz + 1209 Hz 852 Hz + 1336 Hz 852 Hz + 1477 Hz 941 Hz + 1209 Hz 941 Hz + 1477 Hz
188
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.5.4.
This Service Mode is used to check the binary signal output. Signals can be output to the line using the following procedure. (V.34) Press the V, /\ arrow keys to select the "4: MODEM Test" on the display. Press the SET key to select the "4: V34 MODEM". Press the SET key. Press the desired number, and press the "START" key. Press the STOP key twice to exit the service mode. Binary Signal Table Number 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 Signals V34 2400 sr 2400 bps V34 2400 sr 4800 bps V34 2400 sr 7200 bps V34 2400 sr 9600 bps V34 2400 sr 12000 bps V34 2400 sr 14400 bps V34 2400 sr 16800 bps V34 2400 sr 19200 bps V34 2400 sr 21600 bps V34 2800 sr 4800 bps V34 2800 sr 7200 bps V34 2800 sr 9600 bps V34 2800 sr 12000 bps V34 2800 sr 14400 bps V34 2800 sr 16800 bps V34 2800 sr 19200 bps V34 2800 sr 21600 bps V34 2800 sr 24000 bps V34 2800 sr 26400 bps V34 3000 sr 4800 bps V34 3000 sr 7200 bps Number 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Signals V34 3000 sr 9600 bps V34 3000 sr 12000 bps V34 3000 sr 14400 bps V34 3000 sr 16800 bps V34 3000 sr 19200 bps V34 3000 sr 21600 bps V34 3000 sr 24000 bps V34 3000 sr 26400 bps V34 3000 sr 28800 bps V34 3200 sr 4800 bps V34 3200 sr 7200 bps V34 3200 sr 9600 bps V34 3200 sr 12000 bps V34 3200 sr 14400 bps V34 3200 sr 16800 bps V34 3200 sr 19200 bps V34 3200 sr 21600 bps V34 3200 sr 24000 bps V34 3200 sr 26400 bps V34 3200 sr 28800 bps V34 3200 sr 31200 bps Number 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 Signals V34 3429 sr 4800 bps V34 3429 sr 7200 bps V34 3429 sr 9600 bps V34 3429 sr 12000 bps V34 3000 sr 19200 bps V34 3429 sr 16800 bps V34 3429 sr 19200 bps V34 3429 sr 21600 bps V34 3429 sr 24000 bps V34 3429 sr 26400 bps V34 3429 sr 28800 bps V34 3429 sr 31200 bps V34 3429 sr 33600 bps ANSam CM JM INFO0c & TONEB INFO0c & TONEA PPh & AC & ALT
189
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.6.
Initializes RAM, and restores the Function Parameters to their default values. Note: This operation should be performed when the unit is first installed. Press the V, /\ arrow keys to select the "6: RAM initialize" on the display. Press the SET key to select the desired Mode number. Press the "SET" key to initialize RAM. Press the STOP key twice to exit the service mode. RAM Initialization Table No. 01 Initialize Mode PARAMETER INITIALIZE Description Restores the Fax, and Function Parameters to default values. Note: Turn the Power Switch to the OFF, and back to the ON position to enable the parameter settings. Clears the Journal contents. Clears the One-touch, ABBR Numbers, and Phone Books. Clears the Program keys. Clears the Logo, ID, Polling Password. Clears the Printer Error Log. Deletes all setting information, except parameter number 80, and 81, then set default values. Deletes all information in the Flash Memory. Clears all Jobs stored in Flash Memory.
02 03 04 05 06 07 08 09
JOURNAL CLEAR AUTO DIAL CLEAR PROGRAM DIAL CLEAR LOGO/ID/PSWD CLEAR LBP ERROR LOG CLEAR SHIPMENT SET FLASH MEMORY CLEAR ALL JOB CLEAR
190
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.7. 4.2.7.1.
This feature enables the Authorized Servicing Dealers to manage, and improve the machine maintenance to their customers by alerting them of equipment problems. It also can be used as a Supply Sales Tool by alerting the Dealer that the unit is running Low on Toner. The function overview is as follows: 1. The machines printer error information is stored in the Printer Report. 2. The printer report can be manually printed when required. 3. When printer errors occurs, the unit can automatically transmit the Service Alert Report to the preregistered telephone number, or email address. 4. When the unit detects Low Toner, or PM counter reached the maintenance timing, it can automatically transmit the Maintenance Alert Report to the pre-registered telephone number, or email address. Press the V, /\ arrow keys to select the "8: Check & Call" on the display. Press the SET key to select the desired code number. (i.e. 01 Service Alert Fax #, input the telephone No., or for an email address, press the "FAX/EMAIL" Mode key, and input the email address.) Press the "SET" key. Press the STOP key twice to exit the service mode.
4.2.7.2.
Printer Reports
Conditions under which a report can be printed, or transmitted 1. Manual print The Printer Report can be printed by Service Mode 3. (See Sect. 4.2.4.3. of the Service Manual) 2. Automatic transmission/printout a. Service Alert Report When the unit detects an Emergency Printer Error, the unit will immediately transmit the Service Alert Report to the pre-registered telephone number, or email address. However, the unit will not transmit the Service Alert Report if it finds the same error within the same date in the error log. b. Maintenance Alert Report When the unit detects Low Toner, the unit can automatically transmit the Maintenance Alert Report to the pre-registered telephone number, or email address. Refer to the Error Code Table. c. Toner Order Form When the unit detects Low Toner, the unit can automatically print the Toner Order Form with the preregistered order information. d. Call Counter Report When the printer counter reaches the pre-set number, the unit can automatically transmit the Call Counter Report to the pre-registered telephone number, or email address. Note: The Service, and Maintenance Alert Reports are managed in the same manner as the normal memory transmission (Retry, Incomplete, File List, Display while it is transmitting, Journal).
191
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Log O
Tx Remarks Report S Refer to the Mechanical Error Code (E Code) Table. (Sect. 3.6.3.) Out of Toner. Refer to the Jam Error Code (J Code) Table. (Sect. 3.6.2.) Refer to the User Error Code (U Code) Table. (Sect. 3.6.1.) M Low Toner.
192
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.7.3.
*************************************************** DATE MMM-dd-yyyy ***** TIME 03:47 ******** **************************** > SERVISE ALERT REPORT < **************************** LAST PRINT ERROR SERIAL NUMBER (1) CUSTOMER ID (2) FIRMWARE VERSION SC PNL SPC : MMM-dd-yyyy 20:07 E04-01 : : ABC COMPANY : : : 00-00000013
F7-23 F7-24 F7-25 F7-26 F7-27 F7-28 F7-29 F7-30 F7-31 F7-32
PC Print Count PC Scan Count FAX Transmit Count FAX Receive Count FAX Print Count OPC Drum Rotate A4/LT Count A4R/LTR Count A3/LD Count B4/LG Count
: : : : : : : : : :
0 6 0 0 0 0 0 0 0 0
- ***** -31415926535897932384-*********
Explanation of Contents (1) Customer ID (2) Firmware Version (3) Counter Information (4) Print Error Last 30 records (Latest on top)
193
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.7.4.
*************************************************** DATE MMM-dd-yyyy ***** TIME 12:00 ******** **************************** > MAINTENANCE ALERT REPORT < ****************************
LAST PRINT ERROR : MACHINE IS RUNNING OUT OF TONER (1) SERIAL NUMBER CUSTOMER ID : : ABC COMPANY (2)
(4)
NO.DATE & TIME ERROR CODE ERROR COUNT NO.DATE & TIME ERROR CODE ERROR COUNT -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
- ***** -31415926535897932384-***********
Explanation of Contents (1) Low Toner Message (Fixed) (2) Customer ID (3) Firmware Version (4) Transmission / Reception / Copy / Print Counters MACHINE IS RUNNING OUT OF TONER Up to 16 characters (User Identification Code)
194
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.7.5.
**** The toner supply in your machine is running low **** (1) To order a replacement Bottle from your Authorized Dealer
by Phone: by Fax:
Attention: Phone No.: Customer ID: ABC COMPANY (4) Toner Cartridge:
(5)
Serial No.:
Quantity Required:
Explanation of Contents (1) Low Toner Message (Fixed) (2) Toner Order Tel # (3) Toner Order Fax # (4) Customer ID (5) Toner Cartridge The toner supply in your machine is running low Up to 36 digits Up to 36 digits Up to 16 characters (User Identification Code) DQ-TU10J (For DP-8020E/8020P/8016P Except for USA, Canada, and China) DQ-TUJ10K (For DP-8020E/8020P/8016P for USA, Canada, and China)
195
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.7.6.
*************************************************** DATE MMM-dd-yyyy ***** TIME 03:47 ******** ***************************************************************** > SCHEDULED REPORT - CALL COUNTER HAS REACHED PRE-SET VALUE < ***************************************************************** LAST PRINT ERROR : MMM-dd-yyyy 20:07 E04-01 00-00000013 SERIAL NUMBER (1) CUSTOMER ID (2) FIRMWARE VERSION SC PNL SPC : : ABC COMPANY : : : CURRENT 13 13 9 13 13 1 13 0 3 0 0 0 0 0 0 0 0 0 0 1 PM CYCLE (------) 120000 (------) (------) (------)
F7-23 F7-24 F7-25 F7-26 F7-27 F7-28 F7-29 F7-30 F7-31 F7-32
PC Print Count PC Scan Count FAX Transmit Count FAX Receive Count FAX Print Count OPC Drum Rotate A4/LT Count A4R/LTR Count A3/LD Count B4/LG Count
: : : : : : : : : :
0 6 0 0 0 0 0 0 0 0
- ***** -31415926535897932384-*********
Explanation of Contents (1) Customer ID (2) Firmware Version (3) Counter Information (4) Call Counter Pre-Set Value
196
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
4.2.8. 4.2.8.1.
This Service Mode is used to maintain the machine. Use the following procedure for System Maintenance. Press the V, /\ arrow keys to select the "9: System Maintenance" on the display. Press the SET key to select the "1: Send RCVD File". The display changes to the Fax Mode. Select the desired Fax number. Press "START" to send the Fax. After the transmission, the machine returns to the Stand-by Mode. Note: If there is NO File in the machine, this operation will not function. Press the STOP key twice to exit the service mode. System Maintenance Table No. Maintenance Mode 01 Send RCV'D File Description Transfers documents from memory to another fax machine during a fatal printer error.
197
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Note: 1. Panasonic Digital Document Company and other Panasonic Sales Companies reserve the right to change any information enclosed herein without prior notification. (This includes, but is not limited to, parts pricing, availability, and text) 2. Electrical parts supplied may include previously used components. 3. Important Safety Notice Components identified by a mark, have special characteristics important for safety. When replacing any of these components, use only manufacturers specified parts. 4. In New Parts column, "N" indicates part is used only in DP-8020E/8020P/8016P models, "C" indicates part is used in previous models. 5. In Remarks column, "PM" indicates Preventive Maintenance Part". 6. In Remarks column, "RTL" indicates that the Retention Time is limited for this item. After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time. The retention period of availability is dependant on the type of assembly, and in accordance with the laws governing part and product retention. After the end of this period, the assembly will no longer be available. 7. This Unit" which includes other itemized parts is provided as Limited Availability" for your convenience, and will only be offered for up to 3 years after the production of the unit ceases. However, the individual contents of the assembly will be available for the standard period. 8. For Screw identification and Part Number, please refer to the last section of this chapter. 9. Important Notice (Especially in those countries belonging to the European Union): This product is fully compliant with the national laws transposed from the EU Directive on the restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment, effective 1st July 2006 in the EU countries. In order for the product to comply with the RoHS Directive, the six particular substances (lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls, and polybrominated diphenyl ethers) have been either totally eliminated or limited to the concentration level below maximum allowed. Consequently spare parts have been changed to RoHS-compliant parts where applicable. To ensure compliance with the spare parts application of the RoHS legislation, please make sure to follow the details provided in this manual when ordering spare parts and carrying out repairs.
198
Ver. 1.0 OCT 2006
5.1.
Destination Codes
DP-8020E/8020P/8016P
<For DP-8020E / 8020P* / 8016P> Code PA PB PF PK PM Destination Australia; New Zealand England; Singapore; Malaysia; Hong Kong France China Germany; Austria; Italy; Spain Code PP PS PT PU PUG PY Destination Czech; Slovakia; Poland; Hungary Turkey Taiwan USA; Canada; Puerto Rico; Mexico; Panama GSA Saudi Arabia
5.1.1.
<For DP-8020E / 8020P* / 8016P> Code AAR ABR AER AGR AHR AJR AKR ALR AMR APR ARR ATR AUR AVR AWR Destination Austria England Taiwan Germany Netherlands Spain Hong Kong SAR, PRC Australia Switzerland Portugal Belgium Turkey USA; Canada; Puerto Rico France New Zealand Code EER ENR YAR YCR YGR YMR YPR YRR YSR YTR YVR YWR YXR YYR Destination Italy Norway; Sweden Panama; (220 VAC Power Supply) Slovakia Greece Malaysia Czech; Poland; Hungary Russia; Ukraine Saudi Arabia Thailand China South Africa Singapore Mexico; Panama; (120 VAC Power Supply)
Note: 1. DP-8020P is not available for USA and Canada. 2. Model availability may differ as per destination. Please ask your sales company for details.
199
Ver. 1.0 OCT 2006
5.2.
Safety Mark
Cover Assembly
Ref. No. 101 102 103 104 105 106 107 Part Number DZMA004441 DZMA004443 DZMA002394 PJHEC0124Z DZMH000013 DZTE000025 DZJE001189 DZJE001191 DZJE001188 DZHP010632 DZHP010631 DZHP010630 DZTE000052 DZJA001385 DZJA001386 DZJM001318 DZJM001403 DZKN000266 DZML000489 DZKR000038 DZML000491 DZKL000087 DZML000490 DZLF000208 DZML000488 DZNK005316 DZNK005266 PJGFC0033Z DZJF000658 DZJF000657 DZAL000211 DZMA004445 DZJF000662 DZNE000129 PJRCC0005Z DZEC102304R Part Name Cover, Left Scanner Cover, Rear Scanner Cover, Platen Pad, Scanning Hinge, Platen Glass, Platen (L) Plate, Rear Document New Parts C C C C C C C Remarks
DP-8020E/8020P/8016P
Destination All All All All All All PU, PUG PK, PT Other PU, PUG PK, PT Other All All All All All All All All All All All All All PU, PUG Other PK, PT All All All All All All All All All Except PK, PT PK, PT All All All All All All
109 110 112 113 114 116 117 120 121 122 123 124 125 126 127 128 129 131 132 133 135 136 2832 2841
Assembly, Document Plate Glass, Scanning (S) Bracket, Left Hinge Bracket, Right Hinge Guide, OPS Actuator, OPS Spring, Actuator Cover, Bypass Tray Spring, Tray Hold Up Tray, Sub Bypass 2 Actuator, Paper Tray Tray, Sub Bypass Gear, Guide Tray, Bypass Label, Bypass Tray Guide, Rear Set Guide, Front Set Sensor, Photo Cover, Right Scanner Lever, Guide Sheet, Harness Label 3, Sensor PC Board, SNS Harness, MPS PC Board, SSN Screw Screw Screw Screw Screw Screw
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
DZFP001590 DZEC102917R 2910 DZEC103157R Q8 XTB3+8GFN S6 DZPA000086 W9 XTB3+12JFJ X2 DZPA000089 X8 XTB3+8GFJ Y3 XTW3+6LFJ
200
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
103
X2
107
106
1
110 116 117 105 104 W9 S6 114 Y3 112 102 See Fig. 3 S6 101 Y3 See Fig. 7
4
109 Y3 2832
X2 132 X2
2
Y3 113
X8
Q8
129
133 Y3
6
201
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 223 224 225 226 227 228 229 232 233 234 235 236 237 238 239 938 952 Q8 S6 X8 Y1 Y2 Y3 Y11 New Parts N C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
Part Number DZMA004817 DZMA004818 DZMA004453 DZMA004440 DZNK005270 DZJB000447 DZKQ000119 DZJA000187 DZGD000001 DZNK005449 DZNK005268 DZNK005269 DZMA004447 PJGFC1214Z DZJB000186 DZMG000038 DZMA004450 DZMA004449 DZMA004500 DZMA004451 DZMA004452 DZMA004454 FFPTE2719 DZNK005283 PJGTC0053Z DZNK005284 DZJJ000017 K0AHLE000003 DZJB000425 DZKK000120 DZPA000097 DZUJ000023 DZNK004580 DZNK002411 DZNK003248 PJUIC0218Z PJUIC0219Z PJUIC0221Z DZPA000092 PJHSC0025Z XTB3+8GFN DZPA000086 XTB3+8GFJ XTW3+8PFJ XTB3+6FFJ-RP XTW3+6LFJ XSB4+10FJ
Part Name Cover, Front Door Cover, Exit Cover, Connector Label, Toner Bottle Exchange Angle, Door Cover Spring, DC Bracket, Magnet Magnet Label, Laser Caution Label, Toner Bottle Cover 1, Front Label, EPA Plate, Magnet Latch, Waste Toner Box Cover, Left Front Cover, Cover, Cover, Cover, Cover, Label, Right F Card Rear Side Inner Rear F-ROM
Destination All All All All All All All All PK, PT PU,PUG,Other All All All All All All
Label, Heater Main Label, Switch Wire, Front Door Switch, Interlock Bracket, Interlock SW Lever, Interlock Screw Packing, Inner Cover Label, Energy Label, Ground Warning Label, Class A Base, Key Counter Cover, Key Counter Cover, Key Counter Front Screw Gasket Screw Screw Screw Screw Screw Screw Screw
All All All All All For DP-8020E/8020P* All PU,PUG,Other PK All All All All All All All PB PB, PS PK All All All All PA, PB, PF, PM, PP, PS, PY All All All All All All All
202
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
A B C D E
Y11
1
Y2 217 Q8 S6 225
2
216 220
223 224
952
3
233
232
211
203
Ver. 1.0 OCT 2006
5.3.
Safety Mark
Scanner Unit
Ref. No. 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 131 2817 H7 J7 J8 Y3 Part Number DZJB000431 DZLD000024 DZJL000395 DZHP009898 DZJL000396 DZKN000404 DZJF000648 DZLC000001 DZJA001388 DZJA001387 DZJK000106 DZLB000022 DZJA001392 DZKN000403 DZJN000087 DZGG000074 DZLM000214 DZLK000044 DZJM001366 DZAL000211 DZFP001598 FFPFJ0041B XUC4VM XUC7VM XTW3+6LFJ Part Name Frame, Upper Scanner Drum, Wire Wire, Rear Assembly, Drive Shaft Wire, Front Spring, Wire Guide, Wire Pulley, Idler Rail, Rear Rail, Front Holder, Lamp Harness Pulley, Scanner Bracket, Motor Spring, Motor Plate, Rubber Motor, Scanning Bushing Belt, Synchro Sheet, Protection Sensor, Photo Harness, SNS Snap Ring E-Ring E-Ring Screw New Parts C C C C C C C C C C C C C C C C C C C C C C C C C Remarks
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All All All All All All All All All All All All All All All
204
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
319 Y3 318 J8
317 302
2817
317
H7 308
305 310
5
Y3
6
Y3 See Fig. 4
Y3 307
8
205
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 308 2811 2829 2830 2834 J6 X4 X8 Y2 Y3 New Parts C C C C C C C C C C C C C C C C C C C C C C C C C C N C C C C C C C C C C C C C
Part Number DZJB000430 DZJB000432 DZHC000170 DZJA001439 DZJA001438 DZJA001384 DZJM001317 DZJM001347 DZKP000370 DZGM000011 DZTD000004 DZJC000381 DZJC000382 DZJC000383 DZTC000052 DZEA000088 DZJA001389 DZJC000384 DZJA001391 DZKP000280 DZTC000053 DZJM001319 DZJA001390 FFPCP0034 DZHD000036 FFPTE2259 PJZNF3100PK DZJN000093 DZJK000045 DZJK000046 DZLC000001 DZFP001622 DZFP001594 DZFP001639 DZFP001640 XUC3VM XTB3+20GFJ XTB3+8GFJ XTB3+6FFJ-RP XTW3+6LFJ
Part Name Frame, Lower Scanner Frame, CCD Cover 1, Harness Bracket, Dehumidifier Heater Bracket, Harness Cover, CCD Frame, Mirror 1 Slider Plate, Mirror 1 Spring Lamp, Scanning Sheet, Plate, Plate, Plate, Mirror Reflective Wire Lock Rear Wire Holder Front Wire Holder 1
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
PC Board, Inverter Base, Mirror 2 Plate, Pulley Holder, Front Mirror Spring, 2/3 Mirror Mirror 2 Guide, Lamp Harness Holder, Rear Mirror Heater Sleeve, Heater Label, HV CCD Unit Rubber, CCD Frame Clamp Clamp Pulley, Idler Harness, CCD Harness, INV Harness, PTC-AC 1 Harness, PTC-AC 2 E-Ring Screw Screw Screw Screw
206
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
Y3 423 420
1
410
421 420 Y3 J6 421 422 308 420 Y3 408 408 417 418 420 Y3 Y3 412 419
408 308 J6 X4 427 425 406 2830 Y3 424 Y3 403 429 405 430 428
6
2811
Y3 404
2829
409
A
410 Y2
5
401
207
Ver. 1.0 OCT 2006
5.4.
Safety Mark
DP-8020E/8020P/8016P
For DP-8016P
501
Window, Panel
For DP-8020P*
For DP-8020E
502
Cover, Panel
503
C C
504* CR2032 DZJE001173 DZJE001213 DZJE001214 DZJE001216 DZNA001042 DZKB000762 DZKB000641 DZKB000796 DZKB000927 DZKB000929 DZKB000928 511 512 513 514 515 516 517 518 519 520 521 522 PJBCB0018Z-1 DZKB000930 DZKP000365 DZHP010070 DZNA001040 PJBCB0016Z DZKP000385 DZNA001051 MGG03204Z03 DZNA001044 DZKB000931 DZKB000669
505
Cover, Key
C C C C
510
Keys, Numerical
Key, Zoom Key, Function Spring, Speaker Assembly, Speaker Lamp, Active Key, Contrast Plate 1, Ground Cover, Harness Protection LCD Module Holder, LCD Key, A Key, B
C C C C C C C C C C C C
For DP-8020E/8020P* AUR, Other YVR AER AVR For DP-8020E/8020P* All All All All For DP-8020E/8020P* PU, PUG For DP-8016P All PF For DP-8020E/8020P* Except PF, PU, PUG All All All All All All All All All All All All
* Notice: California only: This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
208
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
538
506
537
539
501
505
508
507
S6
511
502
510
509
Q8
A
512
2916
504*
503
518
517
B
515
2917
3
521
519
516
2906
B
A
522
523
520
X8
681
X8
4
522
524
527 528
525
526
2924
522
2904
513
X8
681
514
2923
681
2905
5
X8
534
529
530
531
532
533
2907
535
2918
536
X8
X8
X8
S6
209
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 523 524 525 526 527 528 529 530 New Remarks Destination Parts C For DP-8020E/8020P* All C For DP-8020E/8020P* All C For DP-8020E/8020P* All C All C All C All C C For DP-8020E/8020P* (English) For DP-8020E/8020P* (French) For DP-8020E/8020P* (German) For DP-8020E/8020P* For DP-8020E/8020P* For DP-8020E/8020P* For DP-8020E/8020P* All All All All All All All All All
Part Number DZNA001046 DZNA001047 DZNA001048 DZNA001049 DZKB000924 DZKB000923 DZJE001167 DZJE001169 DZNA001055 Key, Key, Key, Key, Key, Key,
531
DZNA001058 DZNA001059
Sheet, Keyboard
DZNA001053 DZJE001177 DZJA001365 DZJA001366 DZJE001179 DZJE001171 PJYPF3182PU PJYPF3182PF PJYPF3182PK PJYPF3182PT PJYPF3181PU PJYPF3181PB
Sheet, Keyboard Base Cover, Keyboard Bracket, Right Keyboard Bracket, Left Keyboard Cover, Keyboard Lower Cover, Aperture
C C C C C C
For DP-8020E/8020P* All For DP-8016P All PUG, PA, PM, PP, PY PU, PB, PS, For DP-8016P PF PK PT PU, PA, PP, For DP-8020P* PF PK PT PU, PA, PP, For DP-8020E PF PK PT All All RTL/PbF All All All For DP-8020E/8020P* All All All All All All All All All
538
PJYPF3180PF PJYPF3180PK PJYPF3180PT 539 DZNM000005 681 DZJK000023 2904 DZEC102911R 2905 DZEC102912R 2906 DZEC102913R 2907 DZEC103049R 2916 DZFP001627 2917 DZFP001628 2918 DZFP001629 2923 DZFP001533 2924 DZFP001534 Q8 XTB3+8GFN S6 DZPA000086 X8 XTB3+8GFJ
Logo, Panasonic Clamp PC Board, PNL1 PC Board, PNL2 PC Board, PNL3 PC Board, PNL4 Harness, PNL1-PNL3 A Harness, PNL1-PNL3 B Harness, PNL1-PNL4 Harness, PNL2 1 Harness, PNL2 2 Screw Screw Screw
C C C C C C C C C C C C C C
210
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
538
506
537
539
501
505
508
507
S6
511
502
510
509
Q8
A
512
2916
504*
503
518
517
B
515
2917
3
521
519
516
2906
B
A
522
523
520
X8
681
X8
4
522
524
527 528
525
526
2924
522
2904
513
X8
681
514
2923
681
2905
5
X8
534
529
530
531
532
533
2907
535
2918
536
X8
X8
X8
S6
211
Ver. 1.0 OCT 2006
5.5.
Safety Mark
Paper Transportation
Ref. No. 601 602 603 604 606 607 608 609 611 614 615 616 617 618 619 620 621 622 623 624 625 626 627 629 631 632 633 634 635 636 637 638 639 640 641 642 643 647 649 650 651 653 654 655 Part Number DZLA000371 DZLF000748 DZLM000006 DZLM000215 DZJA001405 DZKL000083 DZKL000084 DZKQ000111 DZKK000126 DZKQ000110 DZJF000650 DZJF000651 DZJF000668 DZLM000213 DZLA000363 DZKG000384 DZLF000711 DZLG000035 DZLA000360 DZLF000710 DZKQ000107 DZKG000383 DZJA001402 DZLA000366 DZKK000129 DZJA001420 DZKG000405 DZJF000655 DZJM001345 DZJM001344 DZJM001357 DZJF000653 PJDGC0186Z PJBAC0044Z PJBVC0149Z DZLM000050 DZJH000127 DZJC000387 DZJL000397 DZJF000652 DZLM000212 PJUSC0077Z DZGK000471 DZJM001343 Part Name Roller, Registration Gear, 18 Timing Roller Bushing 2, P6L5 Collar, Timing Roller Bracket, Registration Sensor Lever, Paper Exit Sensor Actuator, Registration Sensor Spring, Registration Sensor Latch, Arm Spring, Latch Guide, Upper Guide, Front Guide, Feed Roller Bushing Roller, Pickup Shaft, Pickup Gear, Pickup Idler Clutch, One-way Roller, Feed Gear, Pickup Drive Spring, Pickup Shaft, Feed Bracket, Pickup Roller, Reverse Arm, Reverse Bracket, Reverse Shaft, Reverse Guide, Lower Film, Lower Guide Film, Rear Guide Film, Front Guide Guide, Duplex Gear, Feed Case, Clutch Spring, Clutch Bushing, P6L8 Collar, Stopper Guide, Shaft Plate, Pressure Tray, Guide Bushing, Left Spacer, Feed Shaft, Reverse Roller Film, Separation Roller New Parts C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C N N N C C C C C C N C C Remarks
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
PM
PM
PM
212
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
Y3
2820
601
609 680
Y2
699 665
602 603
2
S9 H7 695
Y3 698
686 632
626 690
622 S9
635 639 641 J7 640 643 682 651 655 X8 662 657 X8 659 653 654 658 691 643
692
696 684
637 X1
6
X8 S9 642
7
651 656
650
2840
Y3
213
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 656 657 658 659 660 661 662 663 664 665 666 667 668 670 671 680 681 682 684 685 686 688 689 690 691 692 694 695 696 697 698 699 131 2326 New Parts C C C C C C C C C C C C C C C C C N C C C C C C C C C C C C C C C C C C C C C C C C C C C C
Part Number DZKQ000116 DZKQ000117 DZLA000365 DZJF000654 DZKL000085 DZJA001407 DZKP000375 DZJA001406 DZKN000420 DZJB000438 DZJM001378 DZJM001381 DZJM001388 DZNE000132 DZHP012149 DZJK000004 DZJK000023 PJDHC0019Z DZJP000065 PJBVC0151Z DZKN000416 DZJA001427 DZLA000415 DZHP010738 DZHP010737 DZJM001387 L9EAAK000009 L9EAAK000010 PJZFF3180PB DZKG000419 FFPMQ0649 DZJK000057 DZAL000211 DZPK000017
Part Name Spring, Front Spring, Rear Roller, Separation Guide Actuator, No Paper Bracket, Rear Guide Ground Spring Bracket, Front Guide Spring, Fulcrum Bracket, Feed Film, Guide Sheet, Guide Film, Guard Spacer Roller Feed Bypass Assy Clamp Clamp Cam, Feed Board, Pad Spring Spring, Reverse Assembly, Latch Bracket Roller, Feed Torque Limiter 1 Torque Limiter 2 Damper Clutch, Micro 2 Clutch, Micro 1 Assembly, Feed Roller Shaft Pin, Fulcrum Bushing Clamp Sensor, Photo Washer Harness, Paper Tray Sensor Harness, HEPESEN Harness, Frame Ground Snap Ring E-Ring Snap Ring E-Ring Snap Ring Screw Screw Screw Screw
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
PM
PM PM PM
2820 DZFP001597 2839 2840 G6 J7 H7 K5 S9 X1 X8 Y2 Y3 DZFP001608 DZFP001616 FFPFJ0039B XUC4VM FFPFJ0041B XUC5VM FFPFJ0033B DZJM000171 or XTB3+10GFJ XTB3+8GFJ XTB3+6FFJ-RP XTW3+6LFJ
214
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
Y3
2820
601
609 680
Y2
699 665
602 603
2
S9 H7 695
Y3 698
686 632
626 690
622 S9
635 639 641 J7 640 643 682 651 655 X8 662 657 X8 659 653 654 658 691 643
692
696 684
637 X1
6
X8 S9 642
7
651 656
650
2840
Y3
215
Ver. 1.0 OCT 2006
5.6.
Safety Mark
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
For DP-8020E
216
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
X8
748 709 711 713 707 708 718 X8 709 703 712 S6 X8 727 728 X1 704 X8 715 K9 743 G6 719 745 720 G6 C2 741 746 739 725 X8 680 723 729 X8 X8 740 Y3 S9 735 S9 733 736 734 S9 733 X8 S9 738 S9 735 X8 717 X8 K9 737 736 734 732 731 714 131 2844 730 X8 708 710 709 707 709 706 705 J6 716
744
680 726
8
217
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 131 680 2844 C2 G6 J6 K9 S6 S9 X1 X8 Y3 New Remarks Parts C C C For DP-8020E C C C C C C C C C
Part Number DZAL000211 DZJK000004 DZFP001607 DZPB000020 FFPFJ0039B XUC3VM FFPFJ0043B DZPA000086 FFPFJ0033B DZJM000171 XTB3+10GFJ XTB3+8GFJ XTW3+6LFJ
Part Name Sensor, Photo Clamp Harness, DUPSEN Screw Snap Ring E-Ring Snap Ring Screw or Snap Ring Screw Screw Screw
Destination All All All All All All All All All All All All
218
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
X8
748 709 711 713 707 708 718 X8 709 703 712 S6 X8 727 728 X1 704 X8 715 K9 743 G6 719 745 720 G6 C2 741 746 739 725 X8 680 723 729 X8 X8 740 Y3 S9 735 S9 733 736 734 S9 733 X8 S9 738 S9 735 X8 717 X8 K9 737 736 734 732 731 714 131 2844 730 X8 708 710 709 707 709 706 705 J6 716
744
680 726
8
219
Ver. 1.0 OCT 2006
5.7.
Safety Mark
Electrical Parts
Ref. No. 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 Part Number DZHD000038 DZJA001379 DZMC000824 M0CE00000028 DZJE001207 DZMC000825 DZJC000380 DZJA001436 DZJA001437 DZJA001378 DZJA001443 DZKP000374 DZJA001377 DZCC000006 L6FALEGK0018 DZGG000075 DZGG000076 L2BA00000007 DZCC000011 G0A173J00001 G0A352H00002 or DZDG000177 DZTK000002 DZJH000084 DZHE000059 DZJB000449 DZHE000060 DZMC000827 DZPA000093 DZHE000057 LPA3612F-R 829 LPA3612F-BR 830 832 833 680 681 937 939 940 941 FFPTE1621B DZJH000063 DZJF000462 DZJK000004 DZJK000023 DZPA000091 DZMM000038 DZJK000070 DZJB000459 Label, HV Caution Spacer, PCB Guide, Card Clamp Clamp Screw Foot, Damping Clamp Base, CHC C C C C C C C C C LSU Unit C Part Name Cover, PS Bracket, PS Bracket, Right HDD Unit Cover, HDD Handle Bracket, PS SW Bracket, RLB PCB SW Bracket, RLB PCB Base, PS Bracket, MJR PCB Spring, LAN Bracket, PS Cover Switch, Power Fan, Rear Fan, PS PC Board, HSU Switch, Power Coil 1 New Parts C C C C C C C C C C C C C C N C C C C C C Coil 2 N C C C C C C C C PM Remarks
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All All All All
For DP-8020E/8020P* All For DP-8016P All All All Except PU, PT, PK, PUG Except PU, PT, PUG PB, PF, PM, PP, PS Europe only All All All All All All PU, PUG, PK, PT Except PU, PUG, PK, PT All All For DP-8020E/8020P* All All All Except PU, PT, PUG, PK Except PU, PT, PUG, PK All Except PU, PT, PUG, PK
Counter Supporter, PC Board Duct, Exit Holder, Filter Filter, Ozone Guard, Fan Screw Cover, Fan
220
Ver. 1.0 OCT 2006
A A
B B
C C
D D
DP-8020E/8020P/8016P E E
X3 X3
1 1
X3 X3
2 2
825 825
Y4 Y4 815 815
810 810 816 X4 816 X4 828 828 Y3 Y3 823 823 3128 3128 2804 2804 Y6 Y6
Y3 Y3 820 820
3 3
824 824 Y4 Y4 Y6 Y6 Y3 Y3 833 833 2801 2801 822 822 Y3 Y3 814 814 808 808 832 832 812 812 Y3 Y3 Y3 Y3 807 807 805 805 X3 X3 811 811 2902 2902 Y3 Y3 X3 X3 829 829
826 826 809 809 2803 2803 Y3 Y3 3116 3116 806 806 Y3 Y3 681 681 803 803
Y3 Y3
4 4
827 827
5 5
804 804
Y3 Y3
3116 3116 2802 2802 681 681 817 817 Y3 Y3 680 680 2806 2806
8 8 7 7
221
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 2801 2802 2803 2805 2806 New Parts N N C C C C C
Part Name
Remarks See Sect. 5.17 PC Boards (RTL/PbF) RTL/PbF RTL/PbF RTL/PbF See Sect. 5.17 PC Boards See Sect. 5.17 PC Boards (RTL/PbF) See Sect. 5.17 PC Boards (RTL/PbF)
Destination
DZEC102751R Depends on 2901 Destination Depends on Destination Depends on Destination DZJK000068 DZJH000026 XYN3+F8FJ XTB3+20GFJ XTW3+6LFJ XTB3+32GFJ XTW3+6LFJR
2902
PC Board, FXB Clamp 2, Locking Spacer, PCB Screw Screw Screw Screw Screw
C C C C C C C C
222
Ver. 1.0 OCT 2006
A A
B B
C C
D D
DP-8020E/8020P/8016P E E
X3 X3
1 1
X3 X3
2 2
825 825
Y4 Y4 815 815
810 810 816 X4 816 X4 828 828 Y3 Y3 823 823 3128 3128 2804 2804 Y6 Y6
Y3 Y3 820 820
3 3
824 824 Y4 Y4 Y6 Y6 Y3 Y3 833 833 2801 2801 822 822 Y3 Y3 814 814 808 808 832 832 812 812 Y3 Y3 Y3 Y3 807 807 805 805 X3 X3 811 811 2902 2902 Y3 Y3 X3 X3 829 829
826 826 809 809 2803 2803 Y3 Y3 3116 3116 806 806 Y3 Y3 681 681 803 803
Y3 Y3
4 4
827 827
5 5
804 804
Y3 Y3
3116 3116 2802 2802 681 681 817 817 Y3 Y3 680 680 2806 2806
8 8 7 7
223
Ver. 1.0 OCT 2006
5.8.
Safety Mark
Frame Parts
Ref. No. 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 918 920 922 923 924 926 928 929 930 931 932 933 934 935 936 937 938 939 941 942 943 944 945 Part Number DZJB000442 DZJA001371 DZJA001370 DZJA001369 DZJA001368 DZMC000823 DZJB000441 DZJA001372 DZJA001374 DZMC000822 DZKJ000017 DZJC000378 DZKK000119 DZJA001373 DZJD000039 DZJA001367 DZJD000038 DZKP000367 DZKP000366 DZJB000445 DZJB000443 DZJB000440 DZJB000444 DZKN000410 DZJD000044 DZMC000821 DZKP000380 DZJD000043 DZJB000421 DZKP000368 FFPKD07791 DZPA000091 DZPA000092 DZMM000038 DZJB000459 DZHE000055 DZHE000056 DZJB000426 DZFA000098 Part Name Frame, Right Scanner Post, Rear SC Post, Front SC Frame, SC Bracket, LSU 2 Bracket, Center Frame, Left Scanner Bracket, LSU 1 Bracket, Bottle Frame, Front Plate, DIAL Plate, SA Lever, SA Bracket, Toner Plate, Engine FL Bracket, Connector Plate, Engine FU Spring, PS Cover Spring, PS Cover, CST Bracket, Inlet Bracket, SPC PCB Bracket, Rear Spring, Contact Holder, Contact Spring Plate, Base Lead, BTR Frame Holder, Rear Engine Frame, Center Spring, Paper Tray Ground Bracket, Heater Screw Screw Foot, Damping Base, CHC Duct, Upper Duct, Lower Base, Paper Tray L Inlet New Parts C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C Remarks
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All Except PU, PT, PUG All Except PU, PT, PUG Except PU, PT, PUG All All All All
224
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
952
Y3 901
952
Y3 920 Y3 Y3 Y3 923 926 945 Y3 Y10 Y3 Y3 Y3 3116 3007 928 Y7 930 942 943 932 X6 Y2 936 425 424 2831
RLB CN173
922
904 681 Y3 681 908 906 681 907 953 929 935 Y3 909 Y3 918 2819 Y3 916 Y7 913 Y3 910 911 938
5 4
905 680
Y3
Y3
933
X6
Y3
950 3116
931
3011
7
944
3115 X8 3016
948
225
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 946 947 948 950 951 952 953 424 425 680 681 2819 2831 3007 3011 3012 3016 3017 3115 3116 X3 X6 X8 Y2 Y3 Y7 Y10 New Parts C C C C C C C C C C C C C C C C C C C C C C C C C C C
Part Number DZFP001650 DZJL000023 DZJN000076 DZJM001363 DZJB000463 PJHSC0025Z PJBUC0105Z FFPCP0034 DZHD000036 DZJK000004 DZJK000023 DZFP001595 DZFP001641 DZMB000024 DZJB000427 DZJB000428 DZLA000198 DZJF000489 DZJK000067 DZJK000068 XYN3+F8FJ XTB3+8JFJ XTB3+8GFJ XTB3+6FFJ-RP XTW3+6LFJ XNC3FJ XYN4+F6FJ
Part Name Inlet Harness Plate, Ground Gum, Paper Tray Film, Airflow Control Guide, Counter Gasket Plate, Ground Drive Heater Sleeve, Heater Clamp Clamp Harness, WTS Harness, PTC-AC 3 Bracket, Rear Lower Right Base, Right Paper Tray Bracket, Paper Tray Base Roller, Paper Tray Leg, Gum Clamp Clamp Screw Screw Screw Screw Screw Nut Screw
Remarks
Destination All
For DP-8020E/8020P* All All All All PA, PB, PF, PM, PP, PS, PY All All All All All All All All All All All All All All All All All All All All All
226
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
952
Y3 901
952
Y3 920 Y3 Y3 Y3 923 926 945 Y3 Y10 Y3 Y3 Y3 3116 3007 928 Y7 930 942 943 932 X6 Y2 936 425 424 2831
RLB CN173
922
904 681 Y3 681 908 906 681 907 953 929 935 Y3 909 Y3 918 2819 Y3 916 Y7 913 Y3 910 911 938
5 4
905 680
Y3
Y3
933
X6
Y3
950 3116
931
3011
7
944
3115 X8 3016
948
227
Ver. 1.0 OCT 2006
5.9.
Safety Mark
Fuser Unit
Ref. No. Part Number Part Name Guide, SC PCB Plate, Idle Spring Roller, Idle Plate, Ground Cover, Rear Fuser Cover, Front Fuser Spring, Pressure Roller, Idle 2 Guide, Pressure Roller Spring, Opening Sheet A Knob, JAM Release Plate, Knob Roller, ADU Spring, Idle ADU Plate, Rear Pressure Plate, Front Pressure Bushing, Pressure Roller Roller, Pressure Spring, Ground Guide, Front Plate, Ground 2 Frame, Lower Assy Label, High Temperature New Parts C C C C C C C C C C C C C C C C C C C C C C C C Remarks
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All All All All All All All All All All All All All All
1001 DZJF000702 1002 DZKP000373 1003 DZLA000083 1005 DZKP000371 1006 DZJE001199 1007 DZJE001200 1008 DZKN000407 1009 DZLA000357 1010 DZJF000645 1011 1012 1013 1014 1016 1017 1018 1019 1020 1021 1022 1023 1024 DZKQ000109 DZHD000039 DZLF000705 DZJA001409 DZLA000358 DZKN000408 DZKK000124 DZKK000122 DZLM000132 DZLA000362 DZKN000409 DZJF000649 DZKP000372
PM PM
1025 DZJE001223 1026 DZNK005265 PJZSF3180PU PJZSF3180PB 1027 PJZSF2121PU2 PJZSF2121PB2 1028 131 2838 S6 S9 X3 X7 X8 Y5 Y7 PJSCC0015Z DZAL000211 DZFP001606 DZPA000086 FFPFJ0033B DZJM000171 XYN3+F8FJ XYN3+F14FJ XTB3+8GFJ XSN3+W10FJ XNC3FJ
Fuser Unit
Brush, Antistatic Sensor, Photo Harness, Thermistor 1 Screw or Snap Ring Screw Screw Screw Screw Nut
C C C C C C C C C C
PU, PUG, For DP-8020E/8020P* Except PU, PUG, PU, PUG, For DP-8016P Except PU, PUG, All All All All All All All All All All
PT PT PT PT
228
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
X8
1003 1005
1008 1010 1012 1008 S9 S9 1013 1014 X8 Y7 2838 131 1017 1018 1020 1016 1021 X3 1026 X7
1023 1024
X8 6
S6
1020 1025 Y7
1019
1022
229
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 1101 1102 1103 1104 1105 1106 1107 1108 1109 New Parts C C C C C C C C C PM C C C C C N C C C C N Thermostat DZDX000003 1121 1122 1123 1124 1125 1126 1127 1128 1009 1402 2838 S9 X1 X3 X8 DZJA001398 DZJC000385 DZJC000386 DZJA001393 DZBL000061 DZJE001195 FFPLN0005 DZKK000121 DZLA000357 DZLL000005 DZFP001606 FFPFJ0033B DZJM000171 XTB3+10GFJ XYN3+F8FJ XTB3+8GFJ Plate, Terminal 3 Holder, Rear Lamp Holder, Front Lamp Plate, Front Spring Assembly, Thermistor Cover, Fuser Roller Spring Actuator 2 Roller, Idle 2 Wheel, Star Harness, Thermistor 1 or Snap Ring Screw Screw Screw C C C C C C C C C C C C C C C C See For See For Note DP-8020E/8020P* Note DP-8016P See Note
Part Number DZJE001194 DZLF000706 DZLM000052 DZJN000088 DZJF000646 DZHC000168 DZKQ000108 DZJB000434 DZJM001406
Part Name Cover, Exit Roller Gear, Exit Roll Bushing, P6L5 Conductor Roller, Exit 2 Guide, Fuser Roller Actuator Spring, Actuator Base, Separator Separator Frame, Upper Fuser Plate, Rear Spring Gear, E39 Fuser Roller Ring Bushing, Fuser Roller Roller, Fuser Lamp, Fuser Plate, Terminal 1 Fuse, Thermal Plate, Terminal 2
Remarks
Destination All All All All All All All All All All All All All All All PU, PT, PUG Other All All All All All All All All All All All All All All All All All All All
1110 DZJB000429 DZJA001394 DZLF000199 DZPJ000004 DZLM000208 DZLA000418 DZGN000052 1116 DZGN000053 1117 DZJA001396 1118 K5X216BG0002 1119 DZJA001397 K0BDB0000080 1120 1111 1112 1113 1114 1115
PM PM PM
PM
Note: This part is subject to the U.S. Export Administration Laws and Regulations for export or re-export to the countries specified below. Countries subject to embargo are: Cuba, Iran, Iraq, Libya, North Korea, Syria and Sudan. This list is subject to change without further notice. Purchaser of those countries are requested to order the Fuser Unit Assy instead of this part.
230
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
S9
1
1103 1102 1106 1128 1107 1127 1109 1105 X8 X8 1122 1108 X8
A
1104
1109
1110
X1 1124
X8
1123
X3 1117 X8
C
X8
1112 1115
1113
A
X8
C
1114
B
1116
1116
231
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination All All All PU, PUG PK Other All All All PU, PUG PK Other PU, PUG PK Other All All
232
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
1216
2
1217 1202
1201
233
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
1307 DZNE000117 1308 1309 1310 1311 1312 1313 1315 1316 1317 1318 1319 1320 1321 1322 1323 1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344 1345 DZUJ000019 DZJM001309 DZJA001376 DZJA001375 DZJB000420 DZKN000401 DZJM001315 DZJA001380 DZLF000701 DZJE001185 DZLF000702 DZKG000377 DZLF000703 DZKG000378 DZLM000157 PJDGC0170Z DZJL000394 DZHA000225 DZLF000699 DZLM000194 DZUF000009 DZLF000700 DZUF000010 DZJL000215 DZJM001311 DZUJ000021 DZJE001184 DZLM000205 DZUF000008 PJURC0055Z DZJB000424 DZLM000204 DZLF000697 DZLM000203 DZKN000398 PJDIC0011Z DZKG000376
234
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
To Fig. 14
1333 H7 1343 H7 1344 1345 X9 H7 1336 1339 1341 1304 1340 1360 H7 1351 1350 1305 1355 1303 1335 1337 1346 1342 1334 1301 S9
1338 X9 1318 1310 1313 1324 1325 1321 1317 1322 1348 K5 S9 1323 1323 1356
1308
1355 X9
1309
1313 1320 1319 2836 1349 1307 1332 X9 1347 1348 J8 1331 1328 1330 X9 1329 1326 1328 1327
8 7
1315 X9 1316 X9
6
To Fig. 14
235
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. Part Number No. 1346 DZLF000698 1347 DZHP009933 1348 DZLM000207 1349 L2DA00000126 1350 DZJC000395 1351 DZQJ000083 1352 DZHE000067 1353 DZHE000068 1354 DZHE000069 1355 DZHE000071 1356 DZHE000072 1357 DZHE000073 1358 DZHE000074 1359 1360 680 2836 H7 J8 K5 S9 X9 Y8 DZHE000070 PJZYF212500 DZJK000004 DZFP001604 FFPFJ0041B XUC7VM XUC5VM FFPFJ0033B DZJM000171 XTB3+8FFJ XTN3+10GFJ New Parts C C C C C C C C C C C C C C C C C C C C C C C
Part Name Gear, Pipe 15T Developer Unit Bearing, Mag Sensor, Toner Block Tape, Block Sponge, Cover L Sponge, Cover Angle Sponge, Cover S Seal, Developer Side Sponge, Developer Side Sponge, Doctor Blade Side A Sponge, Doctor Blade Side B Sponge, Cover M Bushing Screw Assy Clamp Harness, Toner Sensor Snap Ring E-Ring E-Ring or Snap Ring Screw Screw
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All
236
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
To Fig. 14
1333 H7 1343 H7 1344 1345 X9 H7 1336 1339 1341 1304 1340 1360 H7 1351 1350 1305 1355 1303 1335 1337 1346 1342 1334 1301 S9
1338 X9 1318 1310 1313 1324 1325 1321 1317 1322 1348 K5 S9 1323 1323 1356
1308
1355 X9
1309
1313 1320 1319 2836 1349 1307 1332 X9 1347 1348 J8 1331 1328 1330 X9 1329 1326 1328 1327
8 7
1315 X9 1316 X9
6
To Fig. 14
237
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
PM PM PM PM
PM
PM
238
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
1448 1436 1440 1438 1433 1440 1439 1455 1401 1419 1418 1454 1419 1418 1416 2837 1444 1443 1435 1428 1451 1427 1431 1432 1430 1434 1447
3 2
From Fig. 13
1
1417
1420
1450 1452 1453 1409 1412 1403 1415 1411 1408 1410 1412 1413 X3 From Fig. 13 1449 1414 X9 1445 1421 1426 1425
1414
239
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 1447 1448 1449 1450 1451 1452 1453 1454 1455 2807 2836 2837 X3 X9 New Parts C C C C C C C C C C C C C C
Part Number PJZYF212D00 PJZYF212F00 PJZYF212E00 DZKP000225 DZKP000389 DZHC000173 DZHC000172 DZJM001375 PJZYF212CAZ DZEC102830R DZFP001604 DZFP001605 XYN3+F8FJ XTB3+8FFJ
Part Name Assembly, Charge Corona Assembly, OPC Frame Assembly, Process Unit Plate, Star Wheel Plate, Ground Sheet Plate Film, Charge Side Assembly, Cleaning Pad PC Board, PCL Harness, Toner Sensor Harness, PCL PCB Screw Screw
Remarks
Destination All All All All All All All All All All All All All All
240
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
1448 1436 1440 1438 1433 1440 1439 1455 1401 1419 1418 1454 1419 1418 1416 2837 1444 1443 1435 1428 1451 1427 1431 1432 1430 1434 1447
3 2
From Fig. 13
1
1417
1420
1450 1452 1453 1409 1412 1403 1415 1411 1408 1410 1412 1413 X3 From Fig. 13 1449 1414 X9 1445 1421 1426 1425
1414
241
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
1511 DNQ18AS14W26 1512 DZGB000045 1513 1514 1515 1516 1517 DZLK000043 DZJA001395 DZJA001399 DZJA001401 DZLF000716
1518 DZHP009912 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540 DZLF000718 DZLF000724 DZLF000719 DZLF000717 DZLF000721 DZLF000715 DZLF000722 DZLF000720 DZLF000723 DZLF000713 DZLF000707 DZLF000714 DZLN000022 DZKN000406 DZKG000382 DZLF000709 DZLN000007 DZKN000405 DZKG000381 DZLF000708 DZTY000312 DZTY000311
242
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
131 2822 1540 1511 Y3 X8 1544 Y9 1522 1523 1555 1558 1557 1528 1514 1548 1538 1553 J8 1549 1533 1534 1551 1552 1537 1536 1546 K5 1535 1547 1532 1531 1550 Y3 1543 1512 680 681 680 1545 1562 1559 1560
7
1504
2822
1
1509 1508
1503
1506
2822
1556
1502
3
1527
3F
6
1542
Y3 1554
K5 934
243
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. Part Number No. 1541 DZTY000314 DZTY000315 1542 DZTY000317 1543 DZTY000316 1544 SPM-3 1545 L9AAABFB0001 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561 1562 131 680 681 934 2822 3F J8 K5 X8 Y3 Y9 DZLM000209 DZLM000210 DZLM000216 DZLM000217 DZPK000032 DZTT000614 DZTT000718 XPJ2D14WV PJUIC0310Z DZJG000013 PJZEF2121PU PJSDC0005Z FFPMV0001 PJBVC0150Z PJBLC0026Z PJCGC0003Z XYN26+F4FJ DZAL000211 DZJK000004 DZJK000023 DZJB000421 DZFP001603 XYN3+F5FJ XUC7VM XUC5VM XTB3+8GFJ XTW3+6LFJ XYN4+F8FJ New Parts C C C C N C C C C C C C C N C C C C N N N N C C C C C C C C C C C
Part Name Assembly, Feed Drive Assembly, Exit Drive A Assembly, Exit Drive B Spacer Solenoid Bearing 1 Bearing 2 Bearing 3 Bearing 4 Polyslider Pin 1 Pin 2 Pin 3 Bracket, Solenoid Fly Wheel Ground Spring Kit Drive, Ground Spring Polyslider Washer Spring, Arm Arm Solenoid, Damper Screw Sensor, Photo Clamp Clamp Frame, Center Harness, BSMT Screw E-Ring E-Ring Screw Screw Screw
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
244
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
131 2822 1540 1511 Y3 X8 1544 Y9 1522 1523 1555 1558 1557 1528 1514 1548 1538 1553 J8 1549 1533 1534 1551 1552 1537 1536 1546 K5 1535 1547 1532 1531 1550 Y3 1543 1512 680 681 680 1545 1562 1559 1560
7
1504
2822
1
1509 1508
1503
1506
2822
1556
1502
3
1527
3F
6
1542
Y3 1554
K5 934
245
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All All All All All All All All All All
DZMC000829 DZMC000828 DZML000480 1602 DZML000487 1603 1604 1605 1606 1607 1609 1610 1611 1613 1616 1617 1619 1620 S9 X3 Y1 DZML000479 DZML000484 DZML000481 DZML000482 DZJF000414 DZLA000356 DZML000483 DZLF000465 DZJL000414 DZKG000420 DZJM001369 PJRCC0004Z DZJP000005 FFPFJ0033B XYN3+F8FJ XTW3+8PFJ
1st Paper Tray Other Paper Tray 1st Paper Tray Other Paper Tray
246
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
X3 1613
1619 1609
4
Y1 1617 Y1
5
Y1 1603 1601
6
1602
Y1
247
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All PU,PUG Other PK All All All All All All All All All All All All All All
DZMA003293 DZMA003291 DZJA000852 DZKN000271 DZJM000670 DZML000422 DZKR000032 DZML000507 DZHC000057 DZLF000077 DZML000499 DZML000432 1712 DZML000433 DZML000504 1713 1714 1716 1717 1719 131 430 2832 2846 2851 X6 62 B1 S9 DZJM000676 DZML000500 DZKQ000071 DZJM001241 DZGT000007 DZAL000211 DZJK000046 DZEC102304R DZEC102303R DZFP001968 XTB3+8JFJ XTB3+6JFJ DZPB000007 FFPFJ0033B DZJM000171
RTL/PbF
248
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
1714 1713
S9 S9 2851 131 1716 1709 1710 62 2832 B1 2851 B1 62 See Fig. 18, 19, 20 1706
4
1708
2851 1701
131
3
B1
X6
1707
B1
5
1705
8
249
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1820 1821 1822 New Remarks Destination Parts C All C All C All C All C All C All C All C All C All C All For DP-8020E/8020P* All C C All C All C All C All C All C All C All C All C All C All C All C C C C C C C C C C C C C C C C C For DP-8020E/8020P* For DP-8020E/8020P* For DP-8020E/8020P* All For DP-8020E/8020P* All All All AUR Other All AUR Other All All All All
Part Number DZJA000858 DZJA000853 DZKG000152 DZJM000679 DZKN000270 DZJM000680 DZJM000690 DZKN000269 DZJM000681 DZKN000268 DZJM000677 DZLA000258 DZLM000072 DZJM000692 DZJA000850 DZJA000855 DZKG000154 DZJM000684 DZJM000688 DZKN000273 DZJA000856 PJZEF21200PU
Part Name Plate, Angle Bracket, Left Hinge Shaft, Left Hinge Base, Left Hinge Spring, Lower Left Hinge Guide, Left Spring Holder, Left Spring Spring, Upper Left Hinge Holder, Upper Left Spring Spring, White Front Holder, Stamp Roller, Exit 1 Bushing, P6L8 Sheet, White Guide, White Bracket, Hinge Right Shaft, Hinge Right Base, Hinge Right Guide, Spring Right Spring, Hinge Right Plate, Hinge Right Scanning Pad Hook and Loop Fastener Tape (Loop Side) Solenoid, Stamp Film, Lower Film, Upper Stamp Head Sheet, Protection Assembly, Stamp Unit, Stamp Spring, White Rear Spacer Base, Stamp Harness, Stamp Screw Screw E-Ring Screw Screw, Silver
1823 DZQJ000022 1824 L9AAAABA0002 1825 DZJM000926 1826 DZJM000927 DZHT000027 1827 DZHT000004 1828 DZJM001358 DZHP000237 1829 DZHP000240 1830 DZHP005513 1704 DZKN000271 1717 DZJM001241 2125 DZHP001664 2852 DZFP001967 X6 1N J7 6A B1 XTB3+8JFJ XTB4+8JFJ XUC4VM XTB3+12GFJ DZPB000007
For DP-8020E/8020P*
250
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
J7
1717
1704
1821
1826 1828 1810 1827 1826 1823 2852 1824 1802 1803 1811 1809 B1 J7 1801 1808 1N 1807 1806 6A 1804 1805 1822 1813 X6 X6 1812 2125 1829 1830 1825 1814 1815
251
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 1901 1902 1903 1904 New Parts C C C C C C C C C C C C C C C C C C C C C C C C C C
Part Name Bracket, Adjust Cover, ADF Latch Spring, Latch Motor, ADF Bracket, Motor F Gear, E20S20 F Gear, E28S22 F Gear, E16 Pulley, S27 Belt, Drive 1 Belt, Drive 2 Bracket, Pulley Bracket, Right Clamp Cover, ADF PC Board Switch, Cover Open Spring, Ground Clamp Bushing Harness, ADF Motor Harness, Open Switch Screw Screw Snap Ring or Snap Ring
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All
1905 L6HBHHGC0011 1906 1907 1908 1909 1910 1911 1912 1913 1914 1915 1916 1918 1919 429 698 2848 2850 18 X6 H7 S9 DZJA000849 DZLF000453 DZLF000454 DZLF000315 DZLF000452 DZLK000029 DZLK000023 DZJA000851 DZJA000848 DZJK000018 DZJA001190 DZCF000022 DZKQ000073 DZJK000045 FFPMQ0649 DZFP001964 DZFP001966 XYN3+F6FJ XTB3+8JFJ FFPFJ0041B FFPFJ0033B DZJM000171
252
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
1905 2848 X6
429
1906
X6 1907 1912
18
2
X6 1915
X6
429
3
1913 X6 1914
1902
5
1904 1903
See Fig. 20
1901 X6
8
253
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 2001 2002 2003 2004 2005 2006 New Parts C PM C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
Part Name Roller, Paper Feed Guide, Lower Paper Feed Spring, Timing Actuator, Timing Plate, Pressure Spring, Pressure Plate Lever, Pressure Adjustment Actuator, NP Spring, NP Actuator Roller, Feed Plate, Exit Roller, Exit Pinch Stopper, ADF Cover Shaft, Drive Pinch Roller, Drive Pinch Stopper, Original Guide, Upper Paper Feed Roller, Pre Feed Shaft, Pre Feed Gear 2, Pre Feed Gear 1, Pre Feed Spring, Pick Up Cover, Pad Rubber, Separation D Gear, D26 Holder, Roller Rack, Pickup Guide, Rack Paper Feed Shaft Assembly F Gear, D16 Spring, Pinch Roller Pressure Sheet, ADF Bracket, Center Plate, Exit Sensor, Photo Bushing Bracket, Adjustment Cover, ADF Latch Spring, Latch Clutch Harness, ADF Motor Harness, PNT/REV Screw Snap Ring or Snap Ring
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
2007 DZJM000678 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 DZJM000675 DZKQ000074 DZLA000257 DZKP000251 DZLA000326 DZJM000683 DZKG000150 DZLA000304 DZJM000686 DZJM000673 DZLA000204 DZKG000151 DZJM000414 DZLF000330 DZKN000272 DZJM000682 DZJN000052 DZLF000456 DZJM000685 DZJM000691 DZJM000687 DZKG000153 DZLF000385
PM
PM
2031 DZKR000037 2032 2033 2034 131 698 1901 1902 1903 1904 DZKM000020 DZJA001172 PJBUC0091Z DZAL000211 FFPMQ0649 DZJA000854 DZMA003295 FFPLK0381B DZKN000267
2324 L9EAAJ000020 2848 2849 X6 H7 S9 DZFP001964 DZFP001965 XTB3+8JFJ FFPFJ0041B FFPFJ0033B DZJM000171
254
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
2016
2026
2018 2030 2019 2020 1903 1904 2021 2031 2015 2012 2014 2011 2025 2023 2011
5 3
698 H7 2001
2022 2032
X6
2024
2002
2849 1901
6
2003
X6
2010 698 S9
255
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
2101 DZMA002337 2102 DZJA001470 2103 DZJA001472 2104 DZKG000424 2105 DZJA001473 2106 DZJA000689 2107 DZKN000187 2108 DZJM000486 2109 DZKN000207 2110 DZMA002333 2111 DZKP000215 2112 2113 2114 2115 2116 2117 2118 2119 2120 2121 2122 2123 2124 2125 2126 2127 2128 2129 2130 2131 PJUIC0254Z DZMC000713 DZJA000726 DZJM000449 DZJC000392 DZJP000026 DZJC000391 DZJM000469 DZJA000696 DZJM000475 DZLM000007 DZJM000888 DZJJ000009 DZHP001664 DZMA002329 DZJM001285 DZKP000358 DZJM000429 DZLA000080 DZMA004372
For DP-8020E/8020P*
256
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
2117 2121 2126 X6 2118 2122 X6 M2 2114 F7 2131 2105 6A 2112 2107 2106 2130 2128 2116 X6 2121 2117 2119 X6 2104
J7 2123 2103
2110
2113
257
Ver. 1.0 OCT 2006
Part Name Sensor, Photo Clamp Solenoid, Stamp Stamp Head Assembly, Stamp PC Board, ADF Harness, B1 Sensor Harness, ADF-FG Screw E-Ring Screw Screw, Silver Screw Screw Screw, Thumb
Remarks
1824 L9AAAABA0002 DZHT000027 DZHT000004 DZHP000237 1829 DZHP000240 1827 2847 DZEC101648R 2857 2860 X6 J7 6A B1 B4 F7 M2 DZFP001674 DZFP001714 XTB3+8JFJ XUC4VM XTB3+12GFJ DZPB000007 XTB3+8JFI XSN4+W10FN DZPA000064
For DP-8020E/8020P* For DP-8020E/8020P* For DP-8020E/8020P* For DP-8020E (RTL/PbF) For DP-8020E
All AUR Other AUR Other All All All All All All All All All All
258
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
2117 2121 2126 X6 2118 2122 X6 M2 2114 F7 2131 2105 6A 2112 2107 2106 2130 2128 2116 X6 2121 2117 2119 X6 2104
J7 2123 2103
2110
2113
259
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 2201 2202 2203 2204 2205 2206 2207 2208 2209 New Parts C C C C C C C C C C C C C C C C C C C C C C C
Part Number DZMA002341 DZMA002474 DZMA004339 DZMA004338 DZKQ000012 DZJM000159 DZJA000699 DZMA002348 DZMA002343 DZML000508
Part Name Tray, ADF Input Guide, Original Rear Guide, Original Front Spring, Actuator Base, Actuator Bracket, Actuator Rack, Original Guide Cover, ADF Tray Bottom Tray, Sub Cover, ADF Front Assembly, ADF Tray Pad, Scanning Sensor, Photo Actuator, Original Length F Gear, D14 Base, ADF Plate Spring, ADF Input Tray PC Board, SNS Harness, SNS Screw Screw, Silver Screw or Snap Ring
Remarks
Destination PU,PUG Other All All All All All All All All All PU,PUG Except PU, PUG All All All All All All All All All All All All
104 131 1709 DZHC000057 1710 DZLF000077 2110 DZMA002333 2111 DZKP000215 2832 2856 X6 B1 E8 S9
For DP-8020E
260
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
2202
2201 2203
2211
2856 E8 2856 2207 2204 1709 2205 2207 2206 E8 E8 S9 See Fig. 23
4 3
2856 131
2
2832 1710
X6 2111
E8
2209
6
B1
2210
2110 104
8
261
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 2301 2302 2303 2304 2305 2306 2307 2308 2309 2310 2311 2312 2313 2314 2315 2316 2317 2318 2319 New Parts C C C C C C C C C C C C C C PM C C C C C C C C C C C C C
Part Number DZKG000422 DZKG000423 DZJM000434 DZJM000435 DZJA000694 DZJA000693 DZLF000382 DZLF000036 DZLF000028 DZKG000109 DZJM000411 DZJM000410 DZJM000408 DZLA000205 DZLF000329 DZKG000107 DZKN000209 DZKN000231 DZKQ000042
Part Name Shaft, P8L Shaft, P8S Holder, Spring T Holder, Spring B Plate, Reinforcement B Plate, Reinforcement A Gear, E18 Gear, E25 Gear, E14E25 Shaft, ADF Guide, Rear ADF Guide, Front ADF Holder, ADF Roller, ADF Gear, ADF Shaft, Pre Feed Roller Spring, Latch Spring, Hinge Support Spring, Introduction Spring, Hinge (Silver, i-ADF) Bushing Base, Left Hinge (A) Latch Clutch Clutch Washer Pin
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All
2320 DZKN000422 2321 DZJL000115 2322 DZJA001471 2323 DZMG000018 2324 L9EAAJ000020 2325 L9EAAJ000022 2326 DZPK000017 2327 DZPG000001
262
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
2115 2113 X6 2326 2104 2122 2303 2114 2122 5Z 6A 2112 2853 2322 2302 S9 2307 M2 J7
Y9 2102
J7 2301
1
X6 5Z 2304
2
2103
X6
2320 2318
2305 X6
2859 131
2309
5
S9
2853
2321 2310
H7
263
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 131 2018 2020 2021 2030 2102 2103 2104 2112 2113 2114 2115 2122 New Parts C C PM C C C C C C C C C C C C C C C C C C C C C
Part Number DZAL000211 DZLA000204 DZJM000414 DZLF000330 DZLF000385 DZJA001470 DZJA001472 DZKG000424 PJUIC0254Z DZMC000713 DZJA000726 DZJM000449 DZLM000007
Part Name Sensor, Photo Roller, Pre Feed Gear 2, Pre Feed Gear 1, Pre Feed F Gear, D16 Hinge, Arm Plate, Reinforcement Shaft, P6 Bracket, ADF Mounting Cover, Hinge Stopper, Hinge Film, Hinge Bushing, P6L7.4 Harness, ADF Motor and Clutch Harness, Exit Sensor Screw Screw E-Ring E-Ring Screw Snap Ring Screw, Thumb or Snap Ring
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All
2853 DZFP001705 2859 X6 Y9 J7 5Z 6A H7 M2 S9 DZFP001713 XTB3+8JFJ XYN4+F8FJ XUC4VM XUC6VM XTB3+12GFJ FFPFJ0041B DZPA000064 FFPFJ0033B DZJM000171
264
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
2115 2113 X6 2326 2104 2122 2303 2114 2122 5Z 6A 2112 2853 2322 2302 S9 2307 M2 J7
Y9 2102
J7 2301
1
X6 5Z 2304
2
2103
X6
2320 2318
2305 X6
2859 131
2309
5
S9
2853
2321 2310
H7
265
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. Part Number No. 2401 DZJA001460 2402 DZJA000679 2403 L9AAAEGB0006 2404 2405 2406 2407 2408 2409 2410 DZJM000412 DZJM000432 DZLF000015 DZKN000006 DZJM000431 DZJA000697 DZLF000172 New Parts C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
Part Name Bracket, Front ADF Bracket, Solenoid Solenoid Lever, Release Cover, Gear Bracket Gear, B44 Coil Spring, Idle Gear Plate, Moving Gear Bracket, Moving Gear Gear, B42E27 Solenoid Spring, Reversing Guide 1 Bracket, Reversing Guide 1 Adjuster Joint Bracket, Reversing Guide 2 Spring Connector 3 Gear, B18 Lever, Stopper Stopper, Rubber Bushing, P6 Gear, E18 Drive Holder, Pinch Roller Plate Spring, Ground Bracket, Inverting Guide Front Bracket, Inverting Guide Rear Roller, Inverting Feed Cover, ADF Exit Guide, Inverting 2 Guide, Duplex 2 Guide, Inverting 1 Spring, Duplex 2 Guide Lever, Duplex 2 Guide Connector, TR2 Brush, Antistatic Roller 1, Pinch Spring, Latch Bushing Latch Harness, CLT Screw Screw Snap Ring or Snap Ring
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
2411 L9AABCEZ0001 2412 DZKN000185 2413 DZJA000685 2414 DZJM000422 2415 DZJM000421 2416 DZJA001462 2417 2418 2419 2420 2421 2422 2423 2424 2425 DZKN000188 DZFC001576 DZLF000327 DZJM000430 DZJM000477 DZLM000046 DZLF000332 DZKP000205 DZKP000206
2426 DZJA001466 2427 DZJA001467 2428 2429 2430 2431 2432 2433 2434 2435 1719 2130 2317 2321 2323 2855 X6 5M H7 S9 DZLA000383 DZMA002339 DZJM000424 DZJM000425 DZJM000423 DZKN000186 DZJM000426 DZFC001575 DZGT000007 DZLA000080 DZKN000209 DZJL000115 DZMG000018 DZFP001710 XTB3+8JFJ XYN3+F4FJ FFPFJ0041B FFPFJ0033B DZJM000171
For DP-8020E
266
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
2423
H7
2321 2429
X6 1719
2428
2427
2
2432
2426
X6 2404
2402 2403
5
2401
5M 2435
2422
2420
2417
2415 2403
X6 2414 2416
X6 5M 2855 2411 5M
2435
2855
267
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. Part Number No. 2501 DZJA001459 2502 DZJF000407 2503 DZKP000202 2504 DZJA001461 2505 2506 2507 2508 2509 2510 2511 2512 2513 2514 2515 2516 2517 2518 2519 2520 2521 2522 2523 2524 2525 131 430 1719 2032 2123 2124 2130 2305 2307 2321 DZJF000408 DZJM000409 DZKG000416 DZJM000415 DZLA000206 DZJM000416 DZKQ000031 DZKN000184 DZJM000413 DZJM000442 DZLA000382 DZJM000420 DZLA000381 DZJM000418 DZJM000419 DZHC000105 DZJA000684 DZHC000104 DZJM000491 DZKR000024 DZHP003955 DZAL000211 New Parts C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C For DP-8020E For DP-8020E
Part Name Bracket, Rear ADF Guide, Upper ADF Plate Spring, Pinch Roller Plate, Release Lever Guide, Lower ADF Stopper, Original Shaft, Separation Roller Bushing Roller, Separation Bushing, Torque Limiter Spring, Torque Limiter Spring, Separation Roller Holder, Separation Roller Film, ADF Pre Feed Roller, Exit 3 Guide 1, Reversing Roller, Feed 2 Guide, Feed 2 Roller Holder, Sensor C Actuator, Sensor C Holder, Sensor B2 Actuator, Sensor B2 Film, Reversing Guide 1 Spring, Sensor B2 Assembly, Torque Limiter Sensor, Photo Clamp Brush, Antistatic Sheet, ADF Film, F Band Roller 1, Pinch Plate, Reinforcement B Gear, E18 Bushing Clutch Bracket, Front ADF Lever, Release Lever, Stopper Bush, P6 Harness, Read Point Sensor Harness, Exit Sensor Screw or Snap Ring
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
PM PM PM
DZJK000046 DZGT000007 DZKM000020 DZJM000888 DZJJ000009 DZLA000080 DZJA000694 DZLF000382 DZJL000115 2325 L9EAAJ000022 2401 DZJA001460 2404 DZJM000412 2420 DZJM000430 2422 DZLM000046 2858 DZFP001712 2859 DZFP001713 X6 XTB3+8JFJ FFPFJ0033B S9 DZJM000171
268
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
X6 2032 2502
1
X6
2321
X6
2
2501 S9
2858
1719
2505 2507 2321 2515 2508 S9 2523 2512 2516 X6 2509 2513 2404 2401 2517 2422 S9 2321 2521 2859 2123 X6 131 2524 2859 2522 131 2520 2519 X6 2518 X6 2321 X6 2420 S9 2321 2525 2511 2510 S9 2506
2504
4
2514
5
269
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. New Parts C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C For DP-8020E For DP-8020E For DP-8020E
Part Number
Part Name Motor, ADF Bracket, Gear Shaft Gear, E26S35 Drive Gear, E29 Gear, E21E27 Gear, D24E18 Gear, D16 Gear, D24E18 Bracket, Motor Pulley Belt 2, Timing Bracket, Pulley Shaft 1, Drive Shaft 2, Drive Gear, E21 Drive Bracket, Actuator Spring, Gear Bracket, Rear ADF Cover Bracket, Front ADF Cover Actuator 2 Shaft, Pinch Roller Roller 2, Pinch Plate Spring 2, Discharge Plate 1, Adjustment Actuator 3 Cover, Sub ADF Plate Spring, Pinch Roller Sponge Spring, B1 Sensor Clutch Sensor, Photo Clamp Clamp Cover, ADF Gear, E25 Bushing Latch Gear, E18 Drive Harness, ADF Motor and Clutch Harness, ADF Clutch Harness, B1 Sensor Screw Screw or Snap Ring
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
2601 L6HBJJGB0001 2602 2603 2604 2605 2606 2607 2608 2609 2610 2611 2612 2613 2614 2615 2616 2617 2619 2620 2621 2622 2623 2624 2625 2626 2627 2628 DZJA000695 DZKG000113 DZLF000331 DZLF000283 DZLF000333 DZLF000335 DZLF000008 DZLF000191 DZJA001468 DZLB000013 DZLK000013 DZJA001469 DZKG000114 DZKG000115 DZLF000334 DZJA000675 DZKN000126 DZJA000681 DZJA000680 DZHC000102 DZKG000108 DZLA000211 DZKP000204 DZJA000677 DZHC000103 DZJM000407
2629 DZKP000200 2630 2631 2632 131 429 430 2126 2308 2321 2323 2423 DZJM000476 DZKQ000051 L9EAAJ000021 DZAL000211 DZJK000045 DZJK000046 DZMA002329 DZLF000036 DZJL000115 DZMG000018 DZLF000332
2853 DZFP001705 2854 2857 X6 Y9 S9 DZFP001672 DZFP001674 XTB3+8JFJ XYN4+F8FJ FFPFJ0033B DZJM000171
270
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
2601 S9 2321 429 X6 2602 2308 S9 2604 2610 430 2321 2605 2632 Y9
2 1
2603 2854
2853 429
2608 S9 2609
2321 2612
2604 2321 2423 2616 2308 S9 2620 2617 2619 2623 2611 2613
5
2605 S9 X6
2321
2323 X6 2622 2619 2323 X6 2630 X6 2857 131 X6 2627 2631 2628 X6 2625 2626
8 7
271
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 2701 2702 2703 2704 2705 2706 2707 2708 2709 2710 2711 2712 2713 2714 2321 2423 2624 X6 New Parts C C C C C C C C C C C C C C C C C C
Part Number DZJM000427 DZJA000688 DZKG000112 DZKP000207 DZJF000409 DZLA000384 DZJM001230 DZKP000203 DZJA000678 DZKP000201 DZJM000406 DZKG000110 DZJM001284 DZJM001283 DZJL000115 DZLF000332 DZLA000211 XTB3+8JFJ
Part Name Guide, Upper Feed Guide, Skew Shaft, Drive Pinch Plate Spring, Drive Guide, Sub Top Roller, Drive Guide, Lower Feed Plate Spring, Discharge Plate, Adjustment 2 Plate Spring, Pinch 1 Guide, Inverting Feed Shaft, Pinch 2 Guide, Film A Sheet, Guide 2 Bushing Gear, E18 Drive Roller 2, Pinch Screw
Remarks
Destination All All All All All All All All All All All All All All All All All All
272
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
2423
2321
2706 X6
2
2712
2708 2709
X6
2714
6
2702
2705
8
273
Ver. 1.0 OCT 2006
5.17. PC Boards/Harnesses
Safety Mark Ref. No. Part Number DZEC104116 DZEC104134 DZEC104119 DZEC104125 DZEC104137 DZEC104122 DZEC104131 DZEC104128 DZEC104140 DZEC104117 DZEC104135 DZEC104120 DZEC104126 DZEC104138 DZEC104123 DZEC104132 DZEC104129 DZEC104141 DZEC104118 DZEC104136 DZEC104121 DZEC104127 DZEC104139 DZEC104124 DZEC104133 DZEC104130 DZEC104142 DZEC104147 DZEC102176R PJWPF2740AZ Part Name New Parts Remarks
DP-8020E/8020P/8016P
Destination PU, PUG PA PB, PY PF PK PM PP PS PT PU, PUG PA PB, PY PF PK PM PP PS PT PU, PUG PA PB, PY PF PK PM PP PS PT All All All All All All All All All All PU, PT, PK, PUG Except PU, PT, PK, PUG All All All All All
2801
PC Board, SC
2802 2803 2804 2806 DZEC102751R 2810 2811 2812 2813 DZFP001634 DZFP001635 DZFP001636 DZFP001622 DZFP001632 DZFP001651 DZFP001623 2814 DZFP002105 2815 2816 2817 2818 2819 DZFP001587 DZFP001620 DZFP001598 DZFP001589 DZFP001595
PC PC PC PC
N C C C C C C C
RTL/PbF RTL/PbF
C Harness, LSU 2B Harness, Harness, Harness, Harness, Harness, PS SC-SPC SNS Thermistor 2 WTS C C C C C
274
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
2810
CN52
CN55
2848
2827
CN22
CN21 CN30
2849
CN25
CN28
CN29 CN27
2852
CN53 CN145 CN59 CN51 CN66 CN57
2851
2850
2849
2812 2813
2859
2827
2858
2857
4
2817
CN657 CN721
2853
2856
2828
2812
5
2827
CN650
CN142
CN141
CN726
CN703
CN712 CN715
CN143
CN717
CN722
CN727
2826
CN173 CN172
CN171
2833
275
Ver. 1.0 OCT 2006
Remarks
Destination All All All All All PU, PT, PK, PUG Except PU, PT, PK, PUG All PK, PT, PU, PUG Other All All All All All All All All All All All All All
2820 DZFP001597 2821 2822 2823 2825 DZFP001592 DZFP001603 DZFP001588 DZFP001611 DZFP001596 2826 DZFP002104 DZFP001969 2827 DZFP001971 DZFP001377 DZFP001593 DZFP001594 DZFP001639 DZFP001641 DZFP001653 DZFP001633 DZFP001624 DZEC102303R
Harness, LSU 1 C Harness, LSU 1B Harness, ADF Harness, i-ADF Harness, SCN Harness, INV Harness, PTC-AC 1 Harness, PTC-AC 3 Harness, RLB Harness, HDDPS Harness, CSS PC Board, ADF PC Board, ADF Harness, Harness, Harness, Harness, ADF Motor PNT/REV Open Switch ADF SNS C For DP-8020E
C C C C C C C C C C C C C C C C C C C C C C C
2847 DZEC101648R 2848 2849 2850 2851 DZFP001964 DZFP001965 DZFP001966 DZFP001968
2852 DZFP001967 2853 DZFP001705 2854 2855 2856 2857 DZFP001672 DZFP001710 DZFP001711 DZFP001674
Harness, Stamp Harness, Clutch Harness, Harness, Harness, Harness, Harness, Sensor Harness, Harness, ADF Motor and ADF Clutch CLT SNS B1 Sensor Read Point Exit Sensor KEY
For DP-8020E/8020P* All For DP-8020E For For For For DP-8020E DP-8020E DP-8020E DP-8020E All All All All All All All All All
276
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
2810
CN52
CN55
2848
2827
CN22
CN21 CN30
2849
CN25
CN28
CN29 CN27
2852
CN53 CN145 CN59 CN51 CN66 CN57
2851
2850
2849
2812 2813
2859
2827
2858
2857
4
2817
CN657 CN721
2853
2856
2828
2812
5
2827
CN650
CN142
CN141
CN726
CN703
CN712 CN715
CN143
CN717
CN722
CN727
2826
CN173 CN172
CN171
2833
277
Ver. 1.0 OCT 2006
Part Name
Remarks
Destination PU, PUG, PT PK Except PU, PUG, PT, PK AUR AAR, ABR, AGR AHR, AJR, ALR AMR, APR, ARR AVR, EER, ENR YGR, YPR, YXR Except AAR, ABR, AGR AHR, AJR, ALR AMR, APR, ARR AUR, AVR, EER ENR, YGR, YPR YXR AUR Except AUR All All All All Except PK, PT PK, PT All All All All All All All All All All All All All All All All All All All All All All
2901
PC Board, PS
DZEC103795
2902
PC Board, MJR
RTL/PbF
DZEC103797
DZEC103116R DZEC103117R 2904 DZEC102911R 2906 DZEC102913R 2908 DZEC103665 2909 DZEC102749R DZEC102917R 2910 DZEC103157R 2911 DZFP001617 2912 DZFP001602 2913 DZFP001599 2914 DZFP001600 2915 DZFP001630 2916 DZFP001627 2917 DZFP001628 2918 DZFP001629 2903 2919 DZFP001614 2920 2921 2922 2923 2924 2925 519 DZFP001613 DZFP001612 DZFP001615 DZFP001533 DZFP001534 DZFP001601 MGG03204Z03
PC Board, FXB PC PC PC PC Board, Board, Board, Board, PNL1 PNL3 CST2 CST3
C C C C C C C C C C C C C C C C C C C C C C C C C C
PC Board, SSN Harness, HV 2 Harness, HV 1 Harness, ACIN Harness, ACSW Harness, MJR-FXB Harness, PNL1-PNL3 A Harness, PNL1-PNL3 B Harness, PNL1-PNL4 Harness, Paper Tray Sensor 2 Harness, CL2 Harness, Paper Tray 3 Harness, CL3 Harness, PNL2 1 Harness, PNL2 2 Harness, HT LCD Module Harness, PNL1 Harness, PS Harness, Paper Tray 2 Harness, RLB
DZFP001634 2810 DZFP001635 DZFP001636 2815 DZFP001587 2825 DZFP001611 2833 DZFP001653
278
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
MJR (2902)
1
CN502 CN504
2912
CN501
2915
CN25
2815
CN500
2915
CN11 CN12 CN22 CN10
2815
2815
CN1 CN5 CN2
2918
CN3
2916 2914
CN232
CN230
CN233
CN231
2923
4
2917 2925
2924
2825
2825
CN770 CN771
2919
CN775 CN776
2919
2921
CN772
2915
CN391 CN393
2920
CN777
CN778
CN773
2920
2921
CST3 (2909)
2919
2919
CN800 CN803
2922
2922
CN808
CN806
2825
2922
8
279
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
PM
PM
280
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
S6 See Fig. 31 3004 Y3 3024 Y3 3005 Y3 See Fig. 31 Y3 3009 See Fig. 31 3007 Y3
4 1
3117 Y3
S6
2
931
3001 Y3 3011
S9 S9 X8 631 632
1619
3021 3018
Y3 X8 3020 X8
2130
X8 3016 X8
3015
3018
281
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 3101 3102 3103 3104 3105 New Parts C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
Part Name Guide, Paper Tray Actuator, 2nd Paper Feed Spring, Return Roller, Intermediate Bushing, 8 Metal Gear 1, OP Paper Tray Idle Arm, OP Paper Tray Connect Spring, OP Drive Gear 1, Exit Idle Gear 3, OP Paper Tray Idle Assembly, OP Paper Tray Plate Cover, Heater Holder, Heater Clamp Clamp Edge Saddle Coupling 2 Ring, Stopper Gear, Lift Up Coupling Gear 2, Lift Up Gear 3, Lift Up Gear 1, Lift Up Case B, Lift Up Gear, Worm Spacer, PCB Spacer, PCB Assembly, Lift Up Drive Case A, Lift Up Spring, Lift Up Gear, Lift Up 2 Sheet Assembly, Lift Motor Sensor, Photo Heater Sleeve, Heater Bushing 2, P6L5 Lever, Paper Exit Sensor Latch, Arm Spring, Latch Guide, Front Guide, Feed Roller Roller, Pickup Shaft, Pickup
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
3106 DZLF000740 3108 DZKK000128 3109 DZKQ000115 3110 DZLF000726 3111 DZLF000741 3112 DZHP009928 3113 3114 3115 3116 3117 3118 3119 3120 3121 3122 3123 3124 3125 3127 3128 3132 3133 3135 3136 3137 DZJE001206 DZJE001205 DZJK000067 DZJK000068 DZJK000017 FFPHQ0063 FFPFJ00441 DZLF000733 FFPMF10281 FFPMF1029 DZLF000734 DZJA001412 FFPMF1031B DZJH000066 DZJH000026 DZTY000357 DZJA001568 DZKN000412 DZLF000732 DZJM001076
3138 PJWQF2120PB 131 424 425 603 607 611 614 616 617 619 620 DZAL000211 FFPCP0034 DZHD000036 DZLM000006 DZKL000083 DZKK000126 DZKQ000110 DZJF000651 DZJF000668 DZLA000363 DZKG000384
PM
282
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
3124
3138
3104
3125 3120 3112 3110 3111 3108 680 3109 3106 K9 695 S9 698 S9 S9 627 667 H7 3118
603
2
Y3 3103 3101 2919 131 607 688 614 680 699 2919 668 620 Y3 131 S9 617 666 Y3 698 625 K5 616 624 623 622 665 Y2
611
2908
3128 680
3116 131
3137 681
931
7
283
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 621 622 623 624 625 626 627 665 666 667 668 680 681 688 694 695 698 699 931 2835 2908 New Parts C C C PM C C C C C C C C C C C C C C C C C C C C C C C C C C
Part Number DZLF000711 DZLG000035 DZLA000360 DZLF000710 DZKQ000107 DZKG000383 DZJA001402 DZJB000438 DZJM001378 DZJM001381 DZJM001388 DZJK000004 DZJK000023 DZJA001427 L9EAAK000009 L9EAAK000010 FFPMQ0649 DZJK000057 DZMC000821 DZFP001642 DZEC103665
Part Name Gear, Pickup Idler Clutch, One-way Roller, Feed Gear, Pickup Drive Spring, Pickup Shaft, Feed Bracket, Pickup Stay Feed Film, Guide Sheet, Guide Film, Guard Clamp Clamp Assembly, Latch Bracket Clutch, Micro 2 Clutch, Micro 1 Bushing Clamp Plate, Base Harness, PTC-AC 4 PC Board, CST2 Harness, Paper Tray Sensor 2 Snap Ring Snap Ring E-Ring Snap Ring Snap Ring Screw Screw
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
RTL/PbF
2919 DZFP001614 G6 H7 K5 K9 S9 Y2 Y3 FFPFJ0039B FFPFJ0041B XUC5VM FFPFJ0043B FFPFJ0033B DZJM000171 or XTB3+6FFJ-RP XTW3+6LFJ
284
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
3124
3138
3104
3125 3120 3112 3110 3111 3108 680 3109 3106 K9 695 S9 698 S9 S9 627 667 H7 3118
603
2
Y3 3103 3101 2919 131 607 688 614 680 699 2919 668 620 Y3 131 S9 617 666 Y3 698 625 K5 616 624 623 622 665 Y2
611
2908
3128 680
3116 131
3137 681
931
7
285
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
PM
PM
286
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
See Fig. 33
1
Y3 3003
Y3
3010
931
3001 S9 X8 686 S9 631 632 629 690 S9 3016 3013 3017 Y3 3011
S9 X8
1619
3021 3018
Y3 X8 3020 X8
X8
2130
3016 X8 3012
8
3015
3018
287
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 3101 3102 3103 3104 3105 New Parts C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
Part Name Guide, Paper Tray Actuator, 2nd Paper Feed Spring, Return Roller, Intermediate Bushing, 8 Metal Gear 1, OP Paper Tray Idle Gear 3, OP Paper Tray Idle Cover, Heater Holder, Heater Clamp Clamp Edge Saddle Coupling 2 Ring, Stopper Gear, Lift Up Coupling Gear 2, Lift Up Gear 3, Lift Up Gear 1, Lift Up Case B, Lift Up Gear, Worm Spacer, PCB Spacer, PCB Assembly, Lift Up Drive Case A, Lift Up Motor Spring, Lift Up Gear, Lift Up 2 Sheet Assembly, Lift Motor Ring, Gap Gear 2, 3rd OP Drive Gear 1, 3rd OP Drive Assembly, 3rd OP Drive Plate Sensor, Photo Heater Sleeve, Heater Bushing 2, P6L5 Lever, Paper Exit Sensor Latch, Arm Spring, Latch Guide, Front Guide, Feed Roller Roller, Pickup
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
3106 DZLF000740 3111 DZLF000741 3113 3114 3115 3116 3117 3118 3119 3120 3121 3122 3123 3124 3125 3127 3128 3132 3133 DZJE001206 DZJE001205 DZJK000067 DZJK000068 DZJK000017 FFPHQ0063 FFPFJ00441 DZLF000733 FFPMF10281 FFPMF1029 DZLF000734 DZJA001412 FFPMF1031B DZJH000066 DZJH000026 DZTY000357 DZJA001568
3134 DZGG000072 3135 DZKN000412 3136 DZLF000732 3137 DZJM001076 3138 PJWQF2120PB 3301 DZJB000446 3302 DZLF000743 3303 DZLF000742 3304 DZHP009929 131 424 425 603 607 611 614 616 617 619 DZAL000211 FFPCP0034 DZHD000036 DZLM000006 DZKL000083 DZKK000126 DZKQ000110 DZJF000651 DZJF000668 DZLA000363
PM
288
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
A B C D E
3132
3124
Y3
3125
603
Y3 3103 3101
3111 3118 S9 3302 S9 688 3301 614 611 H7 2919 668 Y3 131 620 S9 621 619 626 625 K5 2835 424 **** 425 680 3113 S9 Y2 3114 698 624 623 622 607
3303
667
2909
3128 680
3116 131
3137
681
931
7
289
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P Safety Mark Ref. No. 620 621 622 623 624 625 626 627 665 666 667 668 680 681 688 694 695 698 699 931 2835 2909 New Parts C C C C PM C C C C C C N N C C C C C C C C C C C C C C C C C C
Part Number DZKG000384 DZLF000711 DZLG000035 DZLA000360 DZLF000710 DZKQ000107 DZKG000383 DZJA001402 DZJB000438 DZJM001378 DZJM001381 DZJM001388 DZJK000004 DZJK000023 DZJA001427 L9EAAK000009 L9EAAK000010 FFPMQ0649 DZJK000057 DZMC000821 DZFP001642 DZEC102749R
Part Name Shaft, Pickup Gear, Pickup Idler Clutch, One-way Roller, Feed Gear, Pickup Drive Spring, Pickup Shaft, Feed Bracket, Pickup Stay Feed Film, Guide Sheet, Guide Film, Guard Clamp Clamp Assembly, Latch Bracket Clutch, Micro 2 Clutch, Micro 1 Bushing Clamp Plate, Base Harness, PTC-AC 4 PC Board, CST3 Harness, Paper Tray Sensor 2 Snap Ring Snap Ring E-Ring Snap Ring
Remarks
Destination All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All
RTL/PbF
2919 DZFP001614 G6 H7 K5 K9 S9 Y2 Y3
FFPFJ0039B FFPFJ0041B XUC5VM FFPFJ0043B FFPFJ0033B Snap Ring DZJM000171 or XTB3+6FFJ-RP Screw XTW3+6LFJ Screw
290
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
A B C D E
3132
3124
Y3
3125
603
Y3 3103 3101
3111 3118 S9 3302 S9 688 3301 614 611 H7 2919 668 Y3 131 620 S9 621 619 626 625 K5 2835 424 **** 425 680 3113 S9 Y2 3114 698 624 623 622 607
3303
667
2909
3128 680
3116 131
3137
681
931
7
291
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination
PJPGC0682Z PJPGC0723Z PJPGC0687Z 3405 PJPGC0724Z PJPGC0690Z PJPGC0725Z 3406 K2CH3DH00002 3407 PJJXC0230Z 3408 PJJXC0228Z 3409 PJQRC0172Z 3410 PJQQC0065Z 3411 PJYCF2120PU0 3412 PJPGC0328Z 3413 PJPGC0371Z 3414 PJPAC0011Z 3416 DZNK004940 3417 PJQRC0008Z 3420 PJPQC0038Z 3421 PJPQC0039Z
Box
PU PUG PU For DP-8020P* PUG PU For DP-8016P PUG For DP-8020E PU, PUG PU, PUG PU, PUG Except PK, PT All PU, PUG PU, PUG PU, PUG Except PK PU, PUG PU, PUG PU, PUG PU, PUG Except PK All All
Cord, AC Power Software CD CD (For Operating Instructions) Installation Instructions Quick Guide Assembly, Cushion Pad Box, Bottom Palette, Wooden Label, Paper Tray Important Notice Process, Cushion R Process, Cushion L
C N N N N C C C C C C C C
292
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
3417
3411 3413
3414
293
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
C N N C N C C C N N C C
294
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
3417
3405
3411
3411
4
3413 3419
6
3414
7
2. For China
295
Ver. 1.0 OCT 2006
5.22. Packing and Accessories 3. For Other Destinations (except USA, Canada and China)
Safety Mark Ref. No. Part Number PJPGC0681Z 3405 PJPGC0686Z PJPGC0689Z K2CH3DH00002 DZFM000115 3406 K2CM3DH00013 K2CT3DH00023 3407 PJJXC0232Z 3408 PJJXC0228Z 3409 PJQRC0172Z PJQQC0066Z 3410 PJQQC0069Z PJQQC0070Z Quick Guide N Software CD CD (For Operating Instructions) Installation Instructions N N N Cord, AC Power C Box N Part Name New Parts Remarks For DP-8020E For DP-8020P* For DP-8016P
DP-8020E/8020P/8016P
Destination Except PU, PUG, PK Except PU, PUG, PK Except PU, PUG, PK PT PA PF, PM, PP PS PB,PY Except PU, PUG, PK Except PK, PT All PA, PB, PF, PM, PS PP PY Except PU, PUG, PK Except PK Except PU, PUG, PK Except PU, PUG, PK Except PK PT All All
3411 PJYCF2120PB0 3412 PJPGC0328Z 3413 PJPGC0327Z 3416 DZNK004942 3417 3418 3420 3421 PJQRC0008Z PJQMC0713Z PJPQC0038Z PJPQC0039Z
Assembly, Cushion Pad Box, Bottom Label, Paper Tray Important Notice Operating Instruction Process, Cushion R Process, Cushion L
C C C C C N C C
296
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
3417
3421 3420 3407, 3408 3409, 3410, 3418 3416 3406 3411 3411 3412
3411
3405
4
3411
6
3413
297
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
RTL/PbF
298
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
3501
3505
3502
3504
4
3505
3502
3504
3503
8
299
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
C C C C
RTL/PbF
300
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
3501
3505
3603
3604 3601
4
3505
3603
301
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination
Cord, Line
C C C
Rosette DZQE000005 PFJA05B001Y DZFB000022 DZFB000001 or Plug, PTT 3907 DZFB000035 DZFB000010 DZFB000009 or K2ME4B000001 DZJE001173 DZJE001213 505 Cover, Key DZJE001214 DZJE001216 506 DZNA001042 Key 513 DZKP000365 Spring, Speaker 514 681 811 831 832 940 DZHP010070 DZJK000023 DZJA001443 DZJK000079 DZJH000063 DZJK000070 Assembly, Speaker Clamp Bracket, MJR PCB Clamp Spacer, PCB Clamp
C C C C C C C C
All All ABR, AKR, AWR AGR AMR ARR,AVR ENR AER, AJR, ATR AUR, EER, YAR YCR, YGR, YMR YPR, YRR, YSR YTR, YVR, YWR YXR, YYR ARR All All YCR, YGR, YSR YVR, YAR, YYR APR AVR AAR ARR ARR ALR ALR AMR For DP-8020E/8020P* AUR, Other YVR AER AVR For DP-8020E/8020P* All All All All All All All All
302
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
1829
1830
3907 3906
832 681
2903, 831
3804
4
3902
303
Ver. 1.0 OCT 2006
Part Number
Destination
2903
C C C
2915 DZFP001630 3909 DZHP010280 DZSD002231 DZSD002234 DZSD002232 DZSD002217 DZSD002219 PJJXC0042Z PJQHC0189Z XTB3+8GFJ XTW3+6LFJR
3802
Quick Guide
C C N C C
AUR Other For DP-8020E/8020P* All See Sect. 5.17 PC Boards (RTL/PbF) See Sect. 5.17 PC Boards (RTL/PbF) All Except YVR, AER AUR, YYR YPR, YRR Other YVR AER All All All All
304
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
1829
1830
3907 3906
832 681
2903, 831
3804
4
3902
305
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
306
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
S6
1
4001
531
4002
See Fig. 5
4
4003
5
4004
6
307
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All All All
RTL/PbF
308
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
4103
805
4102
309
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination
All All
310
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
3501
4201
4202
6
311
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination PU,PUG Other All All All All All All All All All All All
Not Used
312
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
4301
4301 2114
2
W9
X6
3
4303
F7
M2 2112 2113
4
4306 104
5
2113
4301
4301
6
4301
313
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination PU, PUG, PT Except PU, PUG, PT All All All All All All
314
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
4401
1
4401
2
4401
3
1801
6A
4
B1
5
4401
4401
4401
315
Ver. 1.0 OCT 2006
5.31. 2nd/4th Paper Tray and 3rd Paper Tray Packing and Accessories
Safety Mark Ref. No. Part Number DZRB001141 DZRB001145 DZRB001142 DZRB001146 DZRB001139 DZRB001143 DZRB001140 DZRB001144 DZRH000601 DZSM000811 DZNK005417 DZNK005420 DZNK005416 XTB3+8GFJ XTW3+6LFJ A B A B A B A B Part Name New Parts Remarks
DP-8020E/8020P/8016P
4501
PU,PUG For 3rd Paper Tray Other Assembly, Cushion Installation Instructions Label, Paper Size Screw Screw C C C C C All All PU, PUG PK Other All All
Note: A: Carton Box depicts Made in Japan. B: Carton Box depicts Made in Philippines.
316
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
4502
4502
Y3
4504 4505
X8
3
4502
5
4501
6
Fig. 45 2nd / 4th Paper Tray and 3rd Paper Tray Packing and Accesories
317
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination All All PU, PUG, Other PK All All All All All All All All All All All All All All All All All All All All All All
318
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
Y3 681
Y2 405 404
1
680 429 430 3116 936 424, 425 424 2834 2830 2831 808, 814 2833
4 3 2
4602
224
5
4601
319
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination All All All All All All All All All All
320
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
3501
2
3117
3115 681
424 4701
6
321
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Destination All All All All All All All All All All All
322
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P E
2861 4801
3
Y11
238 237
Y2 Y3
4802
323
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Remark Screw Screw Screw Screw Screw E-Ring Screw Silver Screw Blue Screw Screw Screw Silver Screw Snap Ring Snap Ring E-Ring E-Ring
324
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Ref. No. J8 K5 K9 M2 Q8 S6 S9 W9 X1 X2 X3 X4 X6 X7 X8 X9 Y1
Part No. XUC7VM XUC5VM FFPFJ0043B DZPA000064 XTB3+8GFN DZPA000086 FFPFJ0033B XTB3+12JFJ XTB3+10GFJ DZPA000089 XYN3+F8FJ XTB3+20GFJ XTB3+8JFJ XYN3+F14FJ XTB3+8GFJ XTB3+8FFJ XTW3+8PFJ
Figure
Remark E-Ring E-Ring Snap Ring Thumb Screw Screw Screw Snap Ring Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw
325
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Part No.
XTB3+6FFJ-RP
Figure
Remark Screw Screw Screw Screw Screw Nut Screw Screw Screw Screw
326
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
memo
327
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
RTL/PbF
DZEC103795
PC Board, MJR
2902
RTL/PbF
DZEC103797
PC Board, MJR
2902
RTL/PbF
PC PC PC PC PC
SC SC SC SC SC
328
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
DZFN000136
Cord, Line
3903
DZFP000747 DZFP001377 DZFP001533 DZFP001534 DZFP001587 DZFP001588 DZFP001589 DZFP001590 DZFP001592 DZFP001593 DZFP001594 DZFP001595 DZFP001596 DZFP001597 DZFP001598 DZFP001599 DZFP001600 DZFP001601 DZFP001602 DZFP001603
Resistor, 200M ohm Harness, i-ADF Harness, PNL2 1 Harness, PNL2 2 Harness, PS Harness, ILS Harness, Thermistor 2 Harness, MPS Harness, SSN Harness, SCN Harness, INV Harness, WTS Harness, LSU 1 Harness, Paper Tray Sensor Harness, SNS Harness, ACIN Harness, ACSW Harness, HT Harness, HV 1 Harness, BSMT
717 2827 2923 2924 2815 2823 2818 2841 2821 2828 2829 2819 2826 2820 2817 2913 2914 2925 2912 2822
For DP-8020E
329
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
For DP-8020E
For DP-8020E/8020P*
For DP-8020E
For DP-8016P
330
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
PM
For DP-8020E
PM PM
331
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
332
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
333
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
334
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
For DP-8020E/8020P*
For DP-8020E
For DP-8020E
For DP-8020E/8020P*
335
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
336
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
337
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
PM PM
338
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
For DP-8020E
339
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
For DP-8020E
PM
For DP-8020E
PM PM PM PM
340
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
PM PM
For DP-8020E
341
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
For DP-8020E
For DP-8020E
PM For DP-8020E
342
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
343
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
For DP-8020E/8020P* For DP-8020E/8020P* (English) For DP-8020E/8020P* (French) For DP-8020E/8020P* (German) For DP-8020P* For DP-8020E For DP-8016P For DP-8020P* For DP-8020E For DP-8016P For DP-8020P* For DP-8020E For DP-8016P For DP-8020P* For DP-8020E For DP-8016P
344
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
A A A A B B B B
3rd Paper Tray 3rd Paper Tray 2nd/4th Paper Tray 2nd/4th Paper Tray 3rd Paper Tray 3rd Paper Tray 2nd/4th Paper Tray 2nd/4th Paper Tray
345
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
For DP-8020E
For DP-8020E/8020P*
346
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
347
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
PK
PK
PK
PK
PS
PK
For DP-8020E
348
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
Assembly, Control Panel Assembly, Assembly, Assembly, Assembly, Assembly, Assembly, Assembly, Control Control Control Control Control Control Control Panel Panel Panel Panel Panel Panel Panel
For DP-8020P* For For For For For For For DP-8020P* DP-8020P* DP-8020P* DP-8020P* DP-8016P DP-8016P DP-8016P
Assembly, Control Panel Scanning Pad Ground Spring Kit Assembly, Feed Roller Shaft CCD Unit Fuser Unit Fuser Unit Fuser Unit Fuser Unit Bushing Screw Assy Assembly, Cleaning Pad Assembly, Charge Corona Assembly, Process Unit Assembly, OPC Frame Hopper Unit Hopper Unit Spacer Nut Pin 3 Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw E-Ring E-Ring E-Ring E-Ring E-Ring Screw
For DP-8016P
349
Ver. 1.0 OCT 2006
DP-8020E/8020P/8016P
350
Ver. 1.0 OCT 2006