Beruflich Dokumente
Kultur Dokumente
www.fiberhomegroup.com
Agenda
Preparation before configuration Commissioning of data service
FAQ
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
Before the user enters the console, the system will check his identity.
The user should input right username and password. Configuring management VLAN requires the user to be in configuration mode.
The default name and password of an administrator are GEPON, GEPON and EN, GEPON respectively.
www.fiberhomegroup.com
Type cd service after command prompt Admin# in configuration mode to get into directory of commands for VLAN management.
To configure management VLAN, use the following command: set manage vlan name <name> vid <vid> inputport <portlist> [untagged|tagged] <vid>: VLAN ID of management VLAN, ranging between 1 and 4085. <portlist>: Port of the management VLAN. [untagged|tagged]: Specify port of this management VLAN is in Untagged mode or Tagged mode.
Example: set manage vlan name test vid 1000 inputport 19:4 untagged
www.fiberhomegroup.com
set manage vlan name <name> ip <A.B.C.D/M> {<A.B.C.D>}*1 <A.B.C.D/M>: IP address of management VLAN, of it M referring to subnet mask bits. {<A.B.C.D>}*1: Equipment gateway, optional (The setting of gateway is necessary only when equipment and EMS fall within different net sections) Example: set manage vlan name test IP 10.18.250.3/16
www.fiberhomegroup.com
Add Domain
Add System
Add a Module
Time Calibration
End
www.fiberhomegroup.com
Right-click the blank at the Logical Tree tab in the browse tree pane, and then select Add Domain in the shortcut menu to enter the Add Domain dialog box
www.fiberhomegroup.com
Management IP of equipment
www.fiberhomegroup.com
NOTE: Click Save button in the toolbar to save above configuration into the database and enter Edit Mode again.
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
IP address of EMS
IP address of EMS
www.fiberhomegroup.com
Configure ONU port parameters. By clicking FE port configuration, configure the ONU VLAN mode. Configuration of OLT SVLAN. According to ONU configuration and OLT requirement, configure the VLAN profile of OLT QINQ domain.
ONU binding Choose binding ONU, and OLT QINQ profile of PON port.
www.fiberhomegroup.com
Make plans for data service, record ONU MAC address and authentication ID.
Make sure the power supply keep accordance with the requirement of equipment, make sure the voltage within standard range. Check the status indicator of cards Card works properly when ACT indicator of HSWA card, EC4B card, uplink card is on. Communication between ONU and EC4B has been established successfully when LINK indicator of EC4B card is on. Check the type of ONU Check the software version of cards Check the connection status of system. Check the connection between PON port and ONU. Check the connection of uplink cards. Check the connection between EMS and HSWA by serial port.
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
Function Configure the parameters of interface on local end, including service name, type, interface No. and VLAN range, etc.
www.fiberhomegroup.com
Parameters introduction
Service name Customer can define a specific service name for convenience. Starting VLAN ID Start value of VID range:1-4085 VLAN ID end End value of VID range:1-4085 Interface ID (Uplink port ID or TRUNK ID) XFP:10G optical port SFP1G optical port GE10/100/1000M electric port Tag/Untag mode Define VLAN is tagged or untagged Service type Pre-define the type of service
www.fiberhomegroup.com
Function
Configure the data service of ONU side, such as CVLAN, SVLAN, etc.
Configuration
Please refer to Commissioning of AN511606A Data Service (ONU).PPT
www.fiberhomegroup.com
Function introduction
Multiple functions for VLAN tag, VLAN translation and VLAN add of upstream direction. Corresponding operation of VLAN for downstream direction can be executed, according to that of the upstream direction. Configuration for upstream and downstream data is enabled, based on which optional operation can be done according to pre-defined parameters. Operation for VLAN based on PON port and ONU is supported. COS remarking is supported.
www.fiberhomegroup.com
currently.
www.fiberhomegroup.com
Binding for each PON port is enabled. Each PON port can be bound to multiple domains. Multi-cards can share one domain. Domain should be either bound to OUN or PON port.
www.fiberhomegroup.com
Multiple domains can be used for binding one ONU. Binding of domain for multi-ONUs and multi-PON ports is enabled. NoteThe domain cant be used for binding PON port of the line card if it has been bound for ONU under this line card.
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
www.fiberhomegroup.com
Note:
Maximum services of QINQ domain profiles should be less than 22 at each PON port. N:1 transform can only be realized by attaching profile to ONU. PON port does not support N:1 transform unless through other indicators such as COS. OLT QINQ domain requires that VLAN can be processed by downstream data only after MAC address has been learned by upstream data Instead of supporting broadcast packets from downstream direction, OLT QINQ domain transmit the packets transparently to the users without processing VLAN.
www.fiberhomegroup.com
FAQ
www.fiberhomegroup.com
Thank You!
FiberHome Technologies
www.fiberhomegroup.com