Beruflich Dokumente
Kultur Dokumente
NK, NKG
Installation and operating instructions
Declaration of Conformity
We Grundfos declare under our sole responsibility that the products
NK and NKG, to which this declaration relates, are in conformity with the
Council Directives on the approximation of the laws of the EC Member
States relating to
Machinery (98/37/EC).
Standard used: EN 809.
Electrical equipment designed for use within certain voltage limits
(2006/95/EC).
Standards used: MG, MMG, Siemens, Teco: EN 60204-1, EN 60034-1
and EN 60034-5; MMGE: EN 61800-2.
Electromagnetic compatibility (89/336/EEC).
Standards used: MG, MMG, Siemens, Teco: EN 61000-6-2 and
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EC (applies only to products with the ATEX mark on the
nameplate).
Standards used: EN 13463-1 and EN 13463-5. (Declaration of conformity and installation and operating instructions of the motor are
enclosed.)
Bare shaft pump
We Grundfos declare under our sole responsibility that the products
NK and NKG, to which this declaration relates, are in conformity with the
Council Directives on the approximation of the laws of the EC Member
States relating to
Machinery (98/37/EC) and meet Annex II B.
Standard used: EN 809.
Before the pump is taken into operation, the complete machinery into
which the pump is to be incorporated must be declared in accordance with
all relevant regulations.
Dclaration de Conformit
Nous Grundfos dclarons sous notre seule responsabilit que les produits
NK et NKG auxquels se rfre cette dclaration sont conformes aux Directives du Conseil concernant le rapprochement des lgislations des Etats
membres CE relatives
Machines (98/37/CE).
Standard utilis: EN 809.
Matriel lectrique destin employer dans certaines limites
de tension (2006/95/CE).
Standards utiliss: MG, MMG, Siemens, Teco: EN 60204-1,
EN 60034-1 et EN 60034-5; MMGE: EN 61800-2.
Compatibilit lectromagntique (89/336/CEE).
Standards utiliss: MG, MMG, Siemens, Teco: EN 61000-6-2 et
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/CE (sapplique uniquement aux produits avec norme ATEX
cite sur la plaque signaltique).
Standards utiliss: EN 13463-1 et EN 13463-5. (Declaration de conformit et notice d'installation et d'entretien du moteur incluses.)
Pompe arbre nu
Nous Grundfos dclarons sous notre seule responsabilit que les produits
NK et NKG auxquels se rfre cette dclaration sont conformes aux Directives du Conseil concernant le rapprochement des lgislations des Etats
membres CE relatives
Relatif aux machines (98/37/CE) et conforme l'Annexe II B.
Standard utilis: EN 809.
Avant que la pompe ne soit mise en service, la machine complte,
dans laquelle sera incorpore la pompe, doit tre en accord avec toutes
les rglementations en vigueur.
Konformittserklrung
Wir Grundfos erklren in alleiniger Verantwortung, dass die Produkte
NK und NKG, auf die sich diese Erklrung bezieht, mit den folgenden
Richtlinien des Rates zur Angleichung der Rechtsvorschriften der EGMitgliedstaaten bereinstimmen:
Maschinen (98/37/EG).
Norm, die verwendet wurde: EN 809.
Elektrische Betriebsmittel zur Verwendung innerhalb bestimmter
Spannungsgrenzen (2006/95/EG).
Normen, die verwendet wurden: MG, MMG, Siemens, Teco:
EN 60204-1, EN 60034-1 und EN 60034-5; MMGE: EN 61800-2.
Elektromagnetische Vertrglichkeit (89/336/EWG).
Normen, die verwendet wurden: MG, MMG, Siemens, Teco: EN 610006-2 und EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EG (gilt nur fr Produkte mit der ATEX-Kennzeichnung auf
dem Leistungsschild).
Normen, die verwendet wurden: EN 13463-1 und EN 13463-5.
(Die Konformittsbescheinigung und Bedienungsanleitung vom Motor
sind beigefgt.)
Pumpe mit freiem Wellenende
Wir Grundfos erklren in alleiniger Verantwortung, dass die Produkte
NK und NKG, auf die sich diese Erklrung bezieht, mit den folgenden
Richtlinien des Rates zur Angleichung der Rechtsvorschriften der EGMitgliedstaaten bereinstimmen:
Maschinen (98/37/EG), Anhang II B (Herstellererklrung).
Norm, die verwendet wurde: EN 809.
Vor der Inbetriebnahme der Pumpe ist eine Konformittserklrung fr die
gesamte Anlage, in die die Baugruppe "Pumpe mit freiem Wellenende"
eingebaut ist, auszustellen.
Dichiarazione di Conformit
Noi Grundfos dichiariamo sotto la nostra esclusiva responsabilit che i
prodotti NK e NKG ai quali questa dichiarazione se riferisce sono conformi
alle Direttive del Consiglio concernente il ravvicinamento delle legislazioni
degli Stati membri CE relative a
Macchine (98/37/CE).
Standard usato: EN 809.
Materiale elettrico destinato ad essere utilizzato entro certi limiti di tensione (2006/95/CE).
Standard usati: MG, MMG, Siemens, Teco: EN 60204-1, EN 60034-1 e
EN 60034-5; MMGE: EN 61800-2.
Compatibilit elettromagnetica (89/336/CEE).
Standard usati: MG, MMG, Siemens, Teco: EN 61000-6-2 e
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/CE (si applica solo ai prodotti che riportano la sigla ATEX
sulletichetta).
Standard usati: EN 13463-1 e EN 13463-5. (In allegato la dichiarazione di conformit e il manuale di installazione e funzionamento.)
Pompa ad asse nudo
Noi Grundfos dichiariamo sotto la nostra esclusiva responsabilit che i
prodotti NK e NKG ai quali questa dichiarazione se riferisce sono conformi
alle Direttive del Consiglio concernente il ravvicinamento delle legislazioni
degli Stati membri CE relative a
Direttiva Macchine (98/37/CE) e Annex II B.
Standard usato: EN 809.
Si ricorda che se la pompa inserita in un sistema, prima di avviare la
pompa stessa, necessario che tutto il sistema sia in accordo alle norme
di riferimento.
Declaracin de Conformidad
Nosotros Grundfos declaramos bajo nuestra nica responsabilidad que
los productos NK y NKG a los cuales se refiere esta declaracin son
conformes con las Directivas del Consejo relativas a la aproximacin de
las legislaciones de los Estados Miembros de la CE sobre
Mquinas (98/37/CE).
Norma aplicada: EN 809.
Material elctrico destinado a utilizarse con determinadas lmites de
tensin (2006/95/CE).
Normas aplicadas: MG, MMG, Siemens, Teco: EN 60204-1,
EN 60034-1 y EN 60034-5; MMGE: EN 61800-2.
Compatibilidad electromagntica (89/336/CEE).
Normas aplicadas: MG, MMG, Siemens, Teco: EN 61000-6-2 y
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/CE (se refiere slo a productos con la marca ATEX en la
placa de caractersticas).
Normas aplicadas: EN 13463-1 y EN 13463-5. (Se adjuntan la declaracin de conformidad e instrucciones de instalacin y funcionamiento
del motor.)
Bomba a eje libre
Nosotros Grundfos declaramos bajo nuestra nica responsabilidad que
los productos NK y NKG a los cuales se refiere esta declaracin son conformes con las Directivas del Consejo relativas a la aproximacin de las
legislaciones de los Estados Miembros de la CE sobre
Maquinaria (98/37/CE) y cumple con Anexo II B.
Norma aplicada: EN 809.
Antes de la puesta en marcha de la bomba, todo el sistema en que la
bomba va a incorporarse, debe estar de acuerdo con todas las normativas
en vigor.
Grundfos
NK NKG
M
(98/37/EC).
: EN 809.
(2006/95/EC).
: MG, MMG, Siemens, Teco:
EN 60204-1, EN 60034-1 EN 60034-5; MMGE: EN 61800-2.
(89/336/EEC).
: MG, MMG, Siemens, Teco:
EN 61000-6-2 EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EC ( ATEX
).
: EN 13463-1 EN 13463-5.
(
.)
Grundfos
NK NKG
M
(98/37/EC) Annex II B.
: EN 809.
,
.
Declarao de Conformidade
Ns Grundfos declaramos sob nossa nica responsabilidade que os produtos NK e NKG aos quais se refere esta declarao esto em conformidade com as Directivas do Conselho das Comunidades Europeias
relativas aproximao das legislaes dos Estados Membros respeitantes
Mquinas (98/37/CE).
Norma utilizada: EN 809.
Material elctrico destinado a ser utilizado dentro de certos limites de
tenso (2006/95/CE).
Normas utilizadas: MG, MMG, Siemens, Teco: EN 60204-1,
EN 60034-1 e EN 60034-5; MMGE: EN 61800-2.
Compatibilidade electromagntica (89/336/CEE).
Normas utilizadas: MG, MMG, Siemens, Teco: EN 61000-6-2 e
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/CE (apenas aplicvel a produtos com a inscrio ATEX
gravada na chapa de caractersticas).
Normas utilizadas: EN 13463-1 e EN 13463-5. (Em anexo encontra a
Declarao de conformidade e instrues de instalao e funcionamento do motor.)
Bomba com ponta de veio livre
Ns Grundfos declaramos sob nossa nica responsabilidade que os produtos NK e NKG aos quais se refere esta declarao esto em conformidade com as Directivas do Conselho das Comunidades Europeias
relativas aproximao das legislaes dos Estados Membros respeitantes
Maquinaria (98/37/CE) e respeitam o Anexo II B.
Norma utilizada: EN 809.
Antes de colocar a bomba em operao, o equipamento no qual a mesma
ir ser incorporada deve ser declarado de acordo com todas as regulamentaes relevantes.
Overeenkomstigheidsverklaring
Wij Grundfos verklaren geheel onder eigen verantwoordelijkheid dat de
produkten NK en NKG waarop deze verklaring betrekking heeft in overeenstemming zijn met de Richtlijnen van de Raad inzake de onderlinge aanpassing van de wetgevingen van de Lid-Staten betreffende
Machines (98/37/EG).
Norm: EN 809.
Elektrisch materiaal bestemd voor gebruik binnen bepaalde
spanningsgrenzen (2006/95/EG).
Normen: MG, MMG, Siemens, Teco: EN 60204-1, EN 60034-1 en
EN 60034-5; MMGE: EN 61800-2.
Elektromagnetische compatibiliteit (89/336/EEG).
Normen: MG, MMG, Siemens, Teco: EN 61000-6-2 en EN 61000-6-3;
MGE/MMGE: EN 61800-3.
ATEX 94/9/EG (alleen van toepassing voor producten met de ATEX
markering op de typeplaat).
Normen: EN 13463-1 en EN 13463-5. (Overeenkomstigheidsverklaring
is ingesloten in de bedienings- en installatievoorschriften van de
motor.)
Pomp met vrije aseinde
Wij Grundfos verklaren geheel onder eigen verantwoordelijkheid dat de
produkten NK en NKG waarop deze verklaring betrekking heeft in overeenstemming zijn met de Richtlijnen van de Raad inzake de onderlinge aanpassing van de wetgevingen van de Lid-Staten betreffende
Machines (98/37/EG) voldoenende aan Annex II B.
Norm: EN 809.
Voordat de pomp in gebruik wordt genomen, moet de gehele installatie
waarin de pomp zich bevindt overeenstemmend zijn met alle relevante wetgevingen.
Frskran om verensstmmelse
Vi Grundfos frskrar under ansvar, att produkterna NK och NKG, som
omfattas av denna frskran, r i verensstmmelse med Rdets Direktiv
om inbrdes nrmande till EU-medlemsstaternas lagstiftning, avseende
Maskinell utrustning (98/37/EC).
Anvnd standard: EN 809.
Elektrisk material avsedd fr anvndning inom vissa spnningsgrnser
(2006/95/EC).
Anvnda standarder: MG, MMG, Siemens, Teco: EN 60204-1,
EN 60034-1 och EN 60034-5; MMGE: EN 61800-2.
Elektromagnetisk kompatibilitet (89/336/EC).
Anvnda standarder: MG, MMG, Siemens, Teco: EN 61000-6-2 och
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EC (endast fr produkter med ATEX-mrkning p
typskylten).
Anvnda standarder: EN 13463-1 och EN 13463-5. (Frskran om
verensstmmelse samt monterings- och driftsinstruktion medfljer
medlevererad motor.)
Pump utan koppling och motor
Vi Grundfos frskrar under ansvar, att produkterna NK och NKG, som
omfattas av denna frskran, r i verensstmmelse med Rdets Direktiv
om inbrdes nrmande till EU-medlemsstaternas lagstiftning, avseende
Maskinell utrustning (98/37/EC) och uppfyller Bilaga II B.
Anvnd standard: EN 809.
Fre igngkrning av pumpen mste hela applikationen, som pumpen
kommer att vara en del av, stmma verens med samtliga relevanta freskrifter.
Overensstemmelseserklring
Vi Grundfos erklrer under ansvar at produkterne NK og NKG, som
denne erklring omhandler, er i overensstemmelse med Rdets direktiver
om indbyrdes tilnrmelse til EF medlemsstaternes lovgivning om
Maskiner (98/37/EF).
Anvendt standard: EN 809.
Elektrisk materiel bestemt til anvendelse inden for visse spndingsgrnser (2006/95/EF).
Anvendte standarder: MG, MMG, Siemens, Teco: EN 60204-1,
EN 60034-1 og EN 60034-5; MMGE: EN 61800-2.
Elektromagnetisk kompatibilitet (89/336/EF).
Anvendte standarder: MG, MMG, Siemens, Teco: EN 61000-6-2,
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EF (glder kun for produkter med ATEX-mrkning p
typeskiltet).
Anvendte standarder: EN 13463-1 og EN 13463-5. (Motorens
overensstemmelseserklring og monterings- og driftsinstruktion er
vedlagt.)
Pumpe uden kobling og motor:
Vi Grundfos erklrer under ansvar at produkterne NK og NKG, som
denne erklring omhandler, er i overensstemmelse med Rdets direktiver
om indbyrdes tilnrmelse til EF medlemsstaternes lovgivning om
Maskiner (98/37/EF) og opfylder Bilag II B.
Anvendt standard: EN 809.
Fr pumpen tages i brug, skal det komplette maskinanlg hvori den skal
inkorporeres, erklres i overensstemmelse med alle relevante bestemmelser.
Vastaavuusvakuutus
Me Grundfos vakuutamme yksin vastuullisesti, ett tuotteet NK ja NKG,
jota tm vakuutus koskee, noudattavat direktiivej jotka ksittelevt EY:n
jsenvaltioiden koneellisia laitteita koskevien lakien yhdenmukaisuutta
seur.:
Koneet (98/37/EY).
Kytetty standardi: EN 809.
Mrttyjen jnniterajoitusten puitteissa kytettvt shkiset laitteet
(2006/95/EY).
Kytetyt standardit: MG, MMG, Siemens, Teco: EN 60204-1,
EN 60034-1 ja EN 60034-5; MMGE: EN 61800-2.
Elektromagneettinen vastaavuus (89/336/EY).
Kytetyt standardit: MG, MMG, Siemens, Teco: EN 61000-6-2 ja
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EY (soveltuu vain tuotteisiin, joissa on ATEX-merkint
arvokilvess).
Kytetyt standardit: EN 13463-1 ja EN 13463-5. (Moottorin vaatimustenmukaisuusvakuutus ja kyttohjeet sisltyvt toimitukseen.)
Erillinen pumppu
Me Grundfos vakuutamme yksin vastuullisesti, ett tuotteet NK ja NKG,
jota tm vakuutus koskee, noudattavat direktiivej jotka ksittelevt EY:n
jsenvaltioiden koneellisia laitteita koskevien lakien yhdenmukaisuutta
seur.:
Konedirektiivin (98/37/EY) ja liitteen II B vaatimusten mukainen.
Kytetty standardi: EN 809.
Ennen pumpun kyttnottoa koko jrjestelm, jossa pumppua tullaan
kyttmn, on osoitettava kaikkien soveltuvien sdsten mukaiseksi.
Deklaracja zgodnoci
My, Grundfos, owiadczamy z pen odpowiedzialnoci, e nasze wyroby
NK oraz NKG, ktrych deklaracja niniejsza dotyczy, s zgodne z
nastpujcymi wytycznymi Rady d/s ujednolicenia przepisw prawnych
krajw czonkowskich EG:
maszyny (98/37/EG),
zastosowana norma: EN 809.
wyposaenie elektryczne do stosowania w okrelonym zakresie
napi (2006/95/EG),
zastosowane normy: MG, MMG, Siemens, Teco: EN 60204-1,
EN 60034-1 i EN 60034-5; MMGE: EN 61800-2.
zgodno elektromagnetyczna (89/336/EWG),
zastosowane normy: MG, MMG, Siemens, Teco: EN 61000-6-2 i
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EG (dotyczy tylko wyrobw ze znakiem ATEX na tabliczce
znamionowej),
zastosowane normy: EN 13463-1 i EN 13463-5, (deklaracja zgodnoci
oraz instrukcja obsugi i eksploatacji silnika s zaczone.)
Pompa z wolnym waem
My, Grundfos, owiadczamy z pen odpowiedzialnoci, e nasze wyroby
NK oraz NKG, ktrych deklaracja niniejsza dotyczy, s zgodne z
nastpujcymi wytycznymi Rady d/s ujednolicenia przepisw prawnych
krajw czonkowskich EG:
maszyny (98/37/EG) i Aneks II B,
zastosowana norma: EN 809.
Wszystkie urzdzenia wsppracujce z pomp musz by zgodne z
wszystkimi odpowiednimi wytycznymi.
, Grundfos, ,
NK NKG, ,
- :
(98/37/).
: EN 809.
(2006/95/).
: MG, MMG, Siemens, Teco:
EN 60204-1, EN 60034-1 EN 60034-5; MMGE:
EN 61800-2.
(89/336/).
: MG, MMG, Siemens, Teco:
EN 61000-6-2 EN 61000-6-3; MGE/MMGE:
EN 61800-3.
ATEX 94/9/EC (
ATEX ).
: EN 13463-1 EN 13463-5.
(
.)
, Grundfos, ,
NK NKG, ,
- :
(98/37/EC), II B.
: EN 809.
,
, ,
, .
Izjava o ustreznosti
Mi, Grundfos, pod polno odgovornostjo izjavljamo, da so izdelki NK in
NKG, na katere se ta izjava nanaa, v skladu z naslednjimi smernicami
Sveta za uskladitev pravnih predpisov drav lanic Evropske skupnosti:
Stroji (98/37/EG).
Uporabljena norma: EN 809.
Elektrina pogonska sredstva za uporabo v doloenih napetostnih
mejah (2006/95/EG).
Uporabljeni normi: Standards used: MG, MMG, Siemens, Teco:
EN 60204-1, EN 60034-1 in EN 60034-5; MMGE: EN 61800-2.
Elektromagnetna kompatibilnost (89/336/EWG).
Uporabljeni normi: MG, MMG, Siemens, Teco: EN 61000-6-2 in
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EG (velja samo za izdelke z oznako ATEX na tipski
ploici).
Uporabljeni normi: EN 13463-1 in EN 13463-5. (Izjava o ustreznosti ter
navodila za montao in obratovanje motorja sta priloena.)
rpalka s prosto osjo
Mi, Grundfos, pod polno odgovornostjo izjavljamo, da so izdelki NK in
NKG, na katere se ta izjava nanaa, v skladu z naslednjimi smernicami
Sveta za uskladitev pravnih predpisov drav lanic Evropske skupnosti:
Strojna oprema (98/37/EG) in v skladu z aneksom II B.
Uporabljena norma: EN 809.
Vse postrojenje, katerega del je rpalka, mora biti pred zagonom v skladu z
vsemi relevantnimi regulativami.
Konformitsi nyilatkozat
Mi, a Grundfos, egyedli felelssggel kijelentjk, hogy az NK s NKG
termkek, amelyekre jelen nyilatkozat vonatkozik, megfelelnek az Eurpai
Uni tagllamainak jogi irnyelveit sszehangol tancs albbi
irnyelveinek:
Gpek (98/37/EK).
Alkalmazott szabvny: EN 809.
Meghatrozott feszltsg hatrokon bell hasznlt elektromos
eszkzk (2006/95/EK).
Alkalmazott szabvnyok: MG, MMG, Siemens, Teco: EN 60204-1,
EN 60034-1 s EN 60034-5; MMGE: EN 61800-2.
Elektromgneses sszefrhetsg (89/336/EGK).
Alkalmazott szabvnyok: MG, MMG, Siemens, Teco: EN 61000-6-2 s
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EK (csak az ATEX jelzssel elltott termkekre
vonatkozik).
Alkalmazott szabvnyok: EN 13463-1 s EN 13463-5. (A motor
kezelsi utastsa s megelelsgi nyilatkozata mellkelve.)
Szabad tengelyvges szivatty
Mi, a Grundfos, egyedli felelssggel kijelentjk, hogy az NK s NKG
termkek, amelyekre jelen nyilatkozat vonatkozik, megfelelnek az Eurpai
Uni tagllamainak jogi irnyelveit sszehangol tancs albbi
irnyelveinek:
Gpek (98/37/EK) s II B fggelk.
Alkalmazott szabvny: EN 809.
A szivatty zembe helyezse eltt a teljes gpegysget, amelybe a
szivatty beptsre kerlt, a vonatkoz elrsok szerint minsteni kell.
Izjava o usklaenosti
Mi, Grundfos, izjavljujemo uz punu odgovornost, da su proizvodi NK i
NKG, na koje se ova izjava odnosi, sukladni smjernicama Savjeta za
prilagodbu propisa drava-lanica EZ:
Strojevi (98/37/EZ).
Koritena norma: EN 809.
Elektrini pogonski ureaji za koritenje unutar odreenih granica
napona (2006/95/EZ).
Koritene norme: MG, MMG, Siemens, Teco: EN 60204-1, EN 60034-1
i EN 60034-5; MMGE: EN 61800-2.
Elektromagnetska kompatibilnost (89/336/EEZ).
Koritene norme: MG, MMG, Siemens, Teco: EN 61000-6-2 i
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EZ (vrijedi samo za proizvode s ATEX-znakom na natpisnoj
ploic).
Koritene norme: EN 13463-1 i EN 13463-5. (Deklaracija o
usklaenosti te motane i pogonske upute priloeni su uz motor.)
Crpka s golim vratilom
Mi, Grundfos, izjavljujemo uz punu odgovornost, da su proizvodi NK i
NKG, na koje se ova izjava odnosi, sukladni smjernicama Savjeta za
prilagodbu propisa drava-lanica EZ:
Strojevi (98/37/EZ) i zadovoljava Annex II B.
Koritena norma: EN 809.
Prije putanja u pogon crpke, kompletan ureaj u koji je crpka ugraena
mora biti u skladu s odgovarajuim propisima.
Izjava o konformitetu
Mi, Grundfos, izjavljujemo pod potpunom odgovornou da su proizvodi NK i
NKG na koje se odnosi ova izjava u saglasnosti sa smernicama i
uputstvima Saveta za usaglaavanje pravnih propisa lanica Evropske
unije:
maine (98/37/EG),
korien standard: EN 809.
elektrina oprema razvijena za korienje unutar odreenih naponskih
granica (2006/95/EG),
korieni standardi: MG, MMG, Siemens, Teco: EN 60204-1,
EN 60034-1 i EN 60034-5; MMGE: EN 61800-2.
elektromagnetna usaglaenost (89/336/EWG),
korieni standardi: MG, MMG, Siemens, Teco: EN 61000-6-2 i
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EG (odnosi se samo na proizvode sa natpisom ATEX na
natpisnoj ploici),
korieni standardi: EN 13463-1 i EN 13463-5, (deklaracija
konformiteta i uputstva za instalaciju i rad motora su priloeni.)
Vratilo pumpe
Mi, Grundfos, izjavljujemo pod potpunom odgovornou da su proizvodi NK i
NKG na koje se odnosi ova izjava u saglasnosti sa smernicama i
uputstvima Saveta za usaglaavanje pravnih propisa lanica Evropske
unije:
mainerija (98/37/EG) i u skladu je sa Anexom II B,
korien standard: EN 809.
Pre nego to se pumpa pusti u rad kompletna mainerija u koju je pumpa
inkorporisana mora biti u skladu sa lokalnim bitnim regulativama.
, Grundfos ,
NK NKG, ,
:
(98/37/EO).
: EN 809.
(2006/95/EO).
: MG, MMG, Siemens, Teco: EN 60204-1,
EN 60034-1 EN 60034-5; MMGE: EN 61800-2.
(89/336/EO).
: MG, MMG, Siemens, Teco: EN 61000-6-2
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EO ( ATEX
).
: EN 13463-1 EN 13463-5. (
.)
, Grundfos ,
NK NKG, ,
:
(98/37/EO) II B.
: EN 809.
,
, ,
.
Declaraie de conformitate
Noi, Grundfos, declarm asumndu-ne ntreaga responsabilitate c
produsele NK, NKG la care se refer aceast declaraie sunt n
conformitate cu Directivele Consiliului n ceea ce privete alinierea
legislaiilor Statelor Membre ale CE, referitoare la:
Utilaje (98/37/CE).
Standard aplicat: EN 809.
Echipamente electrice destinate utilizrii ntre limite exacte de
tensiune (2006/95/CE).
Standarde aplicate: MG, MMG, Siemens, Teco: EN 60204-1,
EN 60034-1 i EN 60034-5; MMGE: EN 61800-2.
Compatibilitate electromagnetic (89/336/CEE).
Standarde aplicate: MG, MMG, Siemens, Teco: EN 61000-6-2 i
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/CE (se aplic numai la produsele cu marca ATEX pe
plcua de nmatriculare).
Standarde aplicate: EN 13463-1 i EN 13463-5. (Declaraia de
conformitate i instruciunile de instalare i operare ale motorului sunt
incluse.)
Pomp fr arbore
Noi, Grundfos, declarm asumndu-ne ntreaga responsabilitate c
produsele NK, NKG la care se refer aceast declaraie sunt n
conformitate cu Directivele Consiliului n ceea ce privete alinierea
legislaiilor Statelor Membre ale CE, referitoare la:
Utilaje (98/37/CE) i conform Anexei II B.
Standard aplicat: EN 809.
nainte de pornirea pompei, utilajul complet n care este ncorporat pompa
trebuie s fie n conformitate cu toate reglementrile care li se aplic.
Prohlen o konformit
My firma Grundfos prohlaujeme na svou plnou odpovdnost, e vrobky
NK a NKG na n se toto prohlen vztahuje, jsou v souladu s
ustanovenmi smrnice Rady pro sblen prvnch pedpis lenskch
stt Evropskho spoleenstv v oblastech:
strojrenstv (98/37/EG),
pouit norma: EN 809.
provozovn spotebi v toleranci napt (2006/95/EG),
pouit normy: MG, MMG, Siemens, Teco: EN 60204-1, EN 60034-1 a
EN 60034-5; MMGE: EN 61800-2.
elektromagnetick kompatibilita (89/336/EWG),
pouit normy: MG, MMG, Siemens, Teco: EN 61000-6-2 a
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EG (tk se pouze vrobk nesoucch na typovm ttku
znaku ATEX),
pouit normy: EN 13463-1 a EN 13463-5, (prohlen o konformit a
instalan a provozn pedpisy motoru jsou piloeny.)
Vlastn hdel erpadla
My firma Grundfos prohlaujeme na svou plnou odpovdnost, e vrobky
NK a NKG na n se toto prohlen vztahuje, jsou v souladu s
ustanovenmi smrnice Rady pro sblen prvnch pedpis lenskch
stt Evropskho spoleenstv v oblastech:
strojn zazen (98/37/EG) a vyhovujc ploze II B,
pouit norma: EN 809.
Ped uvedenm erpadla do provozu, mus bt kompletn strojn zazen,
jeho soust erpadlo je, deklarovno ve shod se vemi pslunmi
pedpisy.
Prehlsenie o konformite
My firma Grundfos, na svoju pln zodpovednost prehlasujeme, e vrobky
NK, NKG, na ktor sa toto prehlsenie vztahuje, s v slade s
nasledovnmi smernicami Rady pro zblenie prvnych predpisov
lenskch zem Eurpskej nie:
Stroje (98/37/EG),
Pouit norma: EN 809.
Elektrick prevdzkov prostriedky, pouit v uritom naptovom
rozsahu (2006/95/EG),
Pouit normy: MG, MMG, Siemens, Teco: EN 60204-1, EN 60034-1 a
EN 60034-5; MMGE: EN 61800-2.
Elektromagnetick kompatibilita (89/336/EWG),
Pouit normy: MG, MMG, Siemens, Teco: EN 61000-6-2 a
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EG (tka sa iba vrobkov nescich na typovom ttku
znaku ATEX).
Pouit normy: EN 13463-1 a EN 13463-5. (Prehlsenie o konformite
a montny a prevdzkov nvod motora s priloen.)
Vlastn hriade erpadla
My firma Grundfos, na svoju pln zodpovednost prehlasujeme, e vrobky
NK, NKG, na ktor sa toto prehlsenie vztahuje, s v slade s
nasledovnmi smernicami Rady pro zblenie prvnych predpisov
lenskch zem Eurpskej nie:
Zariadenia (98/37/EG) a vyhovujce prlohe II B.
Pouit norma: EN 809.
Pred uvedenm erpadla do prevdzky, mus byt kompletn zariadenie ktorho sastou je aj erpadlo, deklarovan v zhode so vetkmi
prslunmi predpismi.
Vastavuse deklaratsioon
Meie Grundfos deklareerime enda ainuvastutusel, et toode NK ja NKG,
mille kohta kesolev juhend kib, on vastavuses EL nukogu Direktiividega
EM liikmesriikide seaduste hitamise kohta, mis ksitlevad:
Masinad (98/37/EC).
Kasutatud standardit: EN 809.
Madalapinge-elektriseadmed (2006/95/EC).
Kasutatud standardit: MG, MMG, Siemens, Teco: EN 60204-1,
EN 60034-1 ja EN 60034-5; MMGE: EN 61800-2.
Elektrimagnetilist hilduvust (89/336/EEC).
Kasutatud standardit: MG, MMG, Siemens, Teco: EN 61000-6-2 ja
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EC (ainult toodete korral, mille sildikul on ATEX thistus).
Kasutatud standardit: EN 13463-1 ja EN 13463-5. (Mootori vastavuse
deklaratsioon ning paigaldus- ja kasutusjuhend on lisatud.)
Vaba vlliga pump
Meie Grundfos deklareerime enda ainuvastutusel, et toode NK ja NKG,
mille kohta kesolev juhend kib, on vastavuses EL nukogu Direktiividega
EM liikmesriikide seaduste hitamise kohta, mis ksitlevad:
Masinad (98/37/EC) ja rahuldab Osa II B nudeid.
Kasutatud standardit: EN 809.
Enne pumba tsse vtmist peab kogu seadmestik, millesse pump kuulub,
olema heakskiidetud vastavalt asjakohastele eeskirjadele.
Uygunluk Bildirgesi
Biz Grundfos olarak, bu beyanda belirtilen NK ve NKG rnlerinin,
Makina (98/37/EC).
Kullanlan standart: EN 809.
Belli voltaj snrlarnda kullanlmak zere retilmi elektrik donanm
(2006/95/EC).
Kullanlan standartlar: MG, MMG, Siemens, Teco: EN 60204-1, EN
60034-1 ve EN 60034-5; MMGE: EN 61800-2.
Elektromanyetik uyumluluk (89/336/EEC).
Kullanlan standartlar: MG, MMG, Siemens, Teco: EN 61000-6-2 ve
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EC (sadece bilgi etiketinde ATEX iareti bulunan rnlere
uygulanmaktadr).
Kullanlan standartlar: EN 13463-1 ve EN 13463-5. (Motorun uygunluk
beyannamesi ve montaj ve kullanm bilgileri arkaya eklenmitir.)
ile ilgili olarak Avrupa topluluu'na ye Devletlerin yasalarnda yer alan
Belediye Ynetmeliklerine uygun oldugunu, tm sorumluluu bize ait olmak
zere beyan ederiz.
plak aft pompa
Biz Grundfos olarak, bu beyanda belirtilen NK ve NKG rnlerinin,
Makineler (98/37/EC) Annex II B ile uyumlu.
Kullanlan standart: EN 809.
ile ilgili olarak Avrupa topluluu'na ye Devletlerin yasalarnda yer alan
Belediye Ynetmeliklerine uygun oldugunu, tm sorumluluu bize ait olmak
zere beyan ederiz.
Pompa kullanlmaya balamadan nce pompayla birlikte alacak olan
tm makinelerin ilgili kanunlara uygunluu beyan edilmelidir.
Atitikties deklaracija
Mes, Grundfos, su visa atsakomybe pareikiame, kad gaminiai NK ir
NKG, kuriems skirta i deklaracija, atitinka Tarybos Direktyvas dl Europos
Ekonomins Bendrijos ali nari statym suderinimo iose srityse:
Mainos (98/37/EB).
Naudojamas standartas: EN 809.
Elektriniai prietaisai, skirti naudoti tam tikrose tamp ribose
(2006/95/EC).
Naudojami standartai: Standards used: MG, MMG, Siemens, Teco:
EN 60204-1, EN 60034-1 ir EN 60034-5; MMGE: EN 61800-2.
Elektromagnetinis suderinamumas (89/336/EEB).
Naudojami standartai: MG, MMG, Siemens, Teco: EN 61000-6-2 ir
EN 61000-6-3; MGE/MMGE: EN 61800-3.
ATEX 94/9/EB (galioja tik produktams, kuri vardinje ploktelje yra
ATEX enklinimas).
Naudojami standartai: EN 13463-1 ir EN 13463-5. (Variklio atitikties
deklaracija bei rengimo ir naudojimo instrukcija pridedama.)
Siurblys su laisvu velenu
Mes, Grundfos, su visa atsakomybe pareikiame, kad gaminiai NK ir
NKG, kuriems skirta i deklaracija, atitinka Tarybos Direktyvas dl Europos
Ekonomins Bendrijos ali nari statym suderinimo iose srityse:
Mainos (98/37/EB) ir priedas II B.
Naudojamas standartas: EN 809.
Prie pradedant siurbl eksploatuoti, visa ranga, kurioje montuojamas
siurblys, turi bti deklaruota pagal galiojanius reikalavimus.
, Grundfos, ,
NK NKG
- :
(98/37/EC).
, : EN 809.
(2006/95/EC).
, : MG, MMG, Siemens, Teco:
EN 60204-1, EN 60034-1 EN 60034-5; MMGE:
EN 61800-2.
(89/336/EEC).
, : MG, MMG, Siemens, Teco:
EN 61000-6-2 i EN 61000-6-3; MGE/MMGE:
EN 61800-3.
ATEX 94/9/EC ( / ATEX
()).
, : EN 13463-1
EN 13463-5. (
.)
H
, Grundfos, ,
NK NKG
- :
(98/37/EC) Annex II B.
, : EN 809.
, ,
,
.
Bjerringbro, 1st May 2007
NK, NKG
Installation and operating instructions
10
27
46
63
80
97
114
Installatie- en bedieningsinstructies
131
148
Asennus- ja kyttohjeet
165
Monterings- og driftsinstruktion
182
199
217
237
255
273
291
309
323
341
359
377
Paigaldus- ja kasutusjuhend
395
412
429
446
9
1. General information
10
2.
2.1
2.2
10
10
10
3.
3.1
3.2
3.3
3.4
Type key
Type NK
Type NKG
Impeller diameter
Pumped liquids
11
11
11
13
13
4.
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
Technical data
Ambient temperature
Liquid temperature
Operating pressure
Minimum inlet pressure
Maximum inlet pressure
Minimum flow rate
Maximum flow rate
Electrical data
Weight
Sound level
Pump speed relative to material and size
Belt drive
Operation with combustion engine
13
13
13
13
13
13
13
13
13
13
13
14
14
14
5.
5.1
5.2
5.3
5.4
5.5
5.6
5.7
Installation
Preparations before installation
Pump location
Foundation
Grouting
Vibration dampening
Pipework
Bypass
14
14
14
14
15
15
16
16
6.
6.1
6.2
6.3
Alignment
General
How to align the unit
Measuring instruments
16
16
16
20
7.
21
8.
8.1
8.2
Electrical connection
Motor protection
Frequency converter operation
22
22
22
9.
9.1
9.2
9.3
9.4
9.5
Start-up
General
Priming
Checking the direction of rotation
Start-up
Start/stop
22
22
22
23
23
23
10.
10.1
10.2
10.3
10.4
Maintenance
Pump
Mechanical shaft seals
Stuffing box
Motor
23
23
23
23
23
11.
23
12.
12.1
Service
Service kits
24
24
13.
24
14.
25
15.
Disposal
26
Complete unit
General information
Page
1.
CONTENTS
Base frame
2.2 Handling
Pump motors as from 4 kW are supplied with lifting
eyes which must not be used for lifting the entire
pump unit. See figs 1 and 2.
Prior to installation, read these installation and operating instructions. Installation and operation must
comply with local regulations and accepted codes of
good practice.
Fig. 1
10
-A -BAQE
Type range
NKG
NKGE
Nominal diameter of suction port
(DN)
Fig. 2
3. Type key
For units without motor, the motor data are left out, and for bare
shaft pumps, the coupling and motor data are left out.
3.1 Type NK
Reduced performance = .1
Example
NK 32 -125 .1 /142 A1 -F -A
-BAQE
Type range
NK
NKE
Nominal diameter of discharge port (DN)
Nominal impeller diameter [mm]
Fig. 4
Type
96145329
A =
A2 =
C =
H =
E =
X =
Fig. 3
NK 80-160/164 A1-F-A-GQQE
Model B 96623450 P2 0612 0005
Q
30 m n 2957 min -1
150 m 3/h H
p/t
16/90 bar/CMAX
Made in Hungary
96145329
Type
11
28, 38
48
55
60
d5 [mm]
24, 32
42
48
60
Code
Temperature
range
BAQE
0C to +120C
16
16
16
16
BAQV
0C to +90C
16
16
16
16
BQQE
0C to +90C
16
16
16
16
BQQV
0C to +90C
16
16
16
16
GQQE
25C to +90C
16
16*
16*
16*
GQQV
20C to +90C
16
16*
16*
16*
AQQE
0C to +90C
25
25
16
16
AQQV
0C to +90C
25
25
16
16
AQAE
0C to +120C
25
25
25
25
AQAV
0C to +90C
25
25
25
25
BQBE
0C to +140C
16
DAQF
0C to +140C
25
25
25
25
BBQE
0C to +120C
16
16
16
16
Code
Temperature range
SNE
SNO
SNF
30C to +120C
16
* 25C to +60C
Fig. 5
Stuffing box
12
Pos.
Code
Description
Stuffing box
Cooling method
P2
[%]
100
70
Barrier fluid
60
50
EFF 2
80
Without cooling
Materials
EFF 1
90
20 25 30 35 40 45 50 55 60 65 70 75 80
t [C]
1000
Fig. 6
2250
3500
4750
NK:
For heating systems, the water quality should meet VDI 2035.
The maximum flow rate must not exceed the values stated for the
individual pump on page 465, as otherwise there is a risk of for
instance cavitation and overload.
4. Technical data
4.1 Ambient temperature
The ambient temperature and the installation altitude are important factors for the motor life, as they affect the life of the bearings
and insulation system.
Maximum ambient temperature:
4.9 Weight
See label on the packing.
The values stated are maximum values, including the upper tolerance of 3 dB according to ISO 4871.
13
To prevent water, dust, etc. from entering the pump, all nozzles
and openings must be kept covered until the pipes are fitted. The
cost of dismantling the pump during start-up to remove a foreign
object can be very high.
650
[mm]
600
Mechanical shaft seals are precision components. If the mechanical shaft seal of a recently installed pump fails, this will normally
happen within the first few hours of operation. The main cause of
such failures is improper installation of the shaft seals or the pipe
for barrier fluid and/or mishandling of the pump during installation.
550
500
450
CuSn10
400
350
TM03 4109 1806
300
EN-GJL-200
250
200
1200
Fig. 7
1600
2000
2400
2800
3200
3600 min-1
5.3 Foundation
60 mm
48 mm
42 mm
32 mm
Speed n min-1
24 mm
1000
11
18
22
1500
10
25
32
38
2000
14
25
2500
17.5
3000
10
20
For higher power outputs, mount an intermediate shaft with pedestal bearings.
Note: The foundation/installation must be carried out in accordance with the following instructions. Non-compliance may result
in functional faults which will damage the pump components.
Grundfos recommends to install the pump on a concrete foundation which is heavy enough to provide permanent and rigid support to the entire pump. The foundation must be capable of
absorbing any vibration, normal strain or shock. As a rule of
thumb, the weight of the concrete foundation should be 1.5 times
the weight of the pump. The concrete foundation must have an
absolutely level and even surface.
Place the pump on the foundation and fasten it. The base frame
must be supported on the whole area. See figs 8 and 9.
Fig. 8
Incorrect installation
Fig. 9
Correct installation
If the engines are installed in closed areas, the combustion air data should particularly be noted as
should the data for exhaust gases.
When draining the tank, make sure to have containers of adequate size ready for this purpose.
5. Installation
5.1 Preparations before installation
Note: It is very important to handle the equipment correctly
before installation.
The contractor must inspect the equipment on delivery and make
sure that it is stored in such a way that corrosion and damage are
avoided.
If more than 6 months will pass before the equipment is put into
operation, it should be considered whether a suitable anti-corrosive agent should be applied to the internal pump parts.
Ensure
that the agent used does not affect the rubber parts with which
it comes into contact.
14
When the foundation bolts are in position, the base frame can be
placed on the foundation. The base frame can now be aligned
using shims, if necessary, so that it is completely horizontal. See
fig. 13.
Shims
Fig. 10 Foundation
Shuttering
The recommended length and width are shown in fig. 10. Note
that the foundation length and width must be 200 mm larger than
the base frame.
The mass of the foundation must be at least 1.5 times the total
mass of the pump. The minimum height of the foundation (hf) can
then be calculated:
m pump 1.5
h f = --------------------------------------------L f B f concrete
The density () of concrete is usually taken as 2,200 kg/m.
In installations where noise-less operation is particularly important, a foundation with a mass up to 5 times that of the pump is
recommended. See also 5.5 Vibration dampening.
Fig. 14 Shuttering
5.4 Grouting
The pump can be delivered with a base frame prepared for grouting. The base frame has a number of holes through which the
concrete is poured. See fig. 11.
Pour holes
Expansion joint
Vibration
damper
Fig. 15 Vibration dampening
The foundation must be provided with bolts for fixing the base
frame. See fig. 12.
Note: Expansion joints must not be fitted to make up for inaccuracy in the pipework, e.g. centre displacement or misalignment of
flanges.
15
The expansion joints should be fitted at a minimum distance of 11 x DN diameter from the pump, both on the suction and the
discharge sides. This prevents turbulence in the joints, thus
ensuring optimum suction conditions and minimum pressure drop
on the discharge side.
Fixing points
5.7 Bypass
The pump is not allowed to run against a closed
valve as this will cause an increase in temperature/
formation of steam in the pump which may cause
damage to the pump.
5.6 Pipework
The pump housing must not be stressed by the pipework. See
7. Flange forces and torques.
The pipes must be of an adequate size, taking the pump inlet
pressure into consideration.
If there is any danger of the pump running against a closed discharge valve, a minimum liquid flow through the pump should be
ensured by connecting a bypass/a drain to the discharge pipe.
Install the pipes so that air locks are avoided, especially on the
suction side of the pump. See fig. 16.
The minimum flow rate must be at least 10% of the maximum flow
rate. The flow rate and head are stated on the pump nameplate.
6. Alignment
6.1 General
90
s2
Fig. 18 Alignment
16
s1
Action
Step
Action
7
Make a rough alignment
of pump and motor, and
tighten the screws with
correct torque in the
base frame. See the
table "Tightening torques".
Hold a straight-edge
against the coupling,
and determine the inaccuracy, if any, with a
feeler gauge.
4
Turn the coupling 90,
and repeat the measurement with straight-edge
and feeler gauge. If the
measured values are
less than 0.1 mm, the
alignment is finished. Go
to point 8.
17
Action
Action
7
Make a rough alignment
of pump and motor, and
tighten the screws with
correct torque in the
base frame. See the
table "Tightening torques".
10
11
12
18
Step
Step
Action
Action
19
13
Step
20
15
14
21
16
22
23
24
18
17
19
Tightening torques
Description
Tightening
torque
[Nm]
Dimensions
M6
10 2
M8
12 2.4
M10
23 4.6
M12
40 8
M16
80 16
M20
120 24
M24
120 24
Air-gap width S2
Outside coupling
diameter
[mm]
Air-gap width S2
[mm]
Standard coupling
Spacer coupling
Nominal
Tolerance
Nominal
Tolerance
80
0/-1
95
0/-1
110
0/-1
125
0/-1
0/-1
140
0/-1
0/-1
160
0/-1
0/-1
200
0/-1
0/-1
225
0/-1
0/-1
250
0/-1
0/-1
20
Horizontal pump,
z-axis,
discharge port
Horizontal pump,
x-axis,
suction port
Stainless steel
Horizontal pump,
z-axis,
discharge port
Horizontal pump,
x-axis,
suction port
Force [N]
Torque [Nm]
Diameter
DN
Fy
Fz
Fx
F*
My
Mz
Mx
M*
32
298
368
315
578
263
298
385
560
40
350
438
385
683
315
368
455
665
50
473
578
525
910
350
403
490
718
65
595
735
648
1155
385
420
525
770
80
718
875
788
1383
403
455
560
823
100
945
1173
1050
1838
438
508
613
910
125
1120
1383
1243
2170
525
665
735
1068
150
1418
1750
1575
2748
613
718
875
1278
50
525
473
578
910
350
403
490
718
65
648
595
735
1155
385
420
525
770
80
788
718
875
1383
403
455
560
823
100
1050
945
1173
1838
438
508
613
910
125
1243
1120
1383
2170
525
665
735
1068
150
1575
1418
1750
2748
613
718
875
1278
200
2100
1890
2345
3658
805
928
1138
1680
Force [N]
Torque [Nm]
Diameter
DN
Fy
Fz
Fx
32
595
735
40
700
875
F*
My
Mz
Mx
M*
630
1155
525
595
770
1120
770
1365
630
735
910
1330
50
945
1155
1050
1820
700
805
980
1435
65
1190
1470
1295
2310
770
840
1050
1540
80
1435
1750
1575
2765
805
910
1120
1645
100
1890
2345
2100
3675
875
1015
1225
1820
125
2240
2765
2485
4340
1050
1330
1470
2135
150
2835
3500
3150
5495
1225
1435
1750
2555
50
1050
945
1155
1820
700
805
980
1435
65
1295
1190
1470
2310
770
840
1050
1540
80
1575
1435
1750
2765
805
910
1120
1645
100
2100
1890
2345
3675
875
1015
1225
1820
125
2485
2240
2765
4340
1050
1330
1470
2135
150
3150
2835
3500
5495
1225
1435
1750
2555
200
4200
3780
4690
7315
1610
1855
2275
3360
21
8. Electrical connection
9. Start-up
The electrical connections should be carried out +by an authorized electrician in accordance with local regulations.
Note: Do not start the pump until it has been filled with liquid and
vented.
9.1 General
In the case of pumps with stuffing box, check that the stuffing box
gland is correctly fitted. It should be possible to turn the pump
shaft manually. When inactive for a long period, the pump should
first be loosened by turning it manually, if it has got stuck. Loosen
the stuffing box or remove the packing.
When pumping drinking water, the pump should be
flushed through with clean water before start-up in
order to remove any foreign matters such as preservatives, test liquid or grease.
9.2 Priming
Closed systems or open systems where the liquid level is
above the pump inlet
1. Close the discharge isolating valve and slowly open the isolating valve in the suction pipe. Both the pump and the suction
pipe should be completely filled with liquid.
2. Slacken the priming plug in order to vent the pump. Once liquid runs out, tighten the priming plug.
The suction pipe and the pump must be filled with liquid and
vented before the pump is started.
Frequency converter operation will often expose the motor insulation system to a heavier load and cause the motor to be more
noisy than usual due to eddy currents caused by voltage peaks.
Check these operating conditions if the pump is driven via a frequency converter:
3. Pour liquid through the hole until the suction pipe and the
pump are completely filled with liquid.
The suction pipe may be filled and vented via the priming plug.
See fig. 16. Alternatively a priming device with funnel can be
installed before the pump.
Open systems where the liquid level is below the pump inlet
Operating
conditions
Action
Particularly noise
critical applications
5. Once the slide valve at the manual venting pump has been
opened, vent the suction pipe using short, rapid pump strokes
until the liquid runs out on the discharge side.
Cable length
Supply voltage
between 500 V
and 690 V
Fit a dU/dt filter between the motor and frequency converter (reduces the voltage
peaks and thus the noise), or check that the
motor has reinforced insulation.
Supply voltage of
690 V and higher
22
E Drain plug
M Priming plug
Supply voltage up Check that the motor is suitable for freto 500 V
quency converter operation.
9.4 Start-up
Before starting the pump, completely open the isolating valve on
the suction side of the pump and leave the isolating valve on the
discharge side almost closed.
Start the pump.
Vent the pump during starting by loosening the air vent screw in
the pump head/cover until a steady stream of liquid runs out of
the vent hole.
Pay attention to the orientation of the vent hole to
ensure that the escaping water does not cause personal injury or damage to the motor or other components.
In hot-water installations, special attention should be
paid to the risk of personal injury caused by scalding
hot water.
When the pipework has been filled with liquid, slowly open the
isolating valve on the discharge side until it is completely open.
If the motor is fitted with a motor with an output
selected on the basis of a specific maximum flow
rate, the motor may be overloaded if the differential
pressure is lower than anticipated.
Check the overload by measuring the motor current consumption
and comparing the value with the nominal current stated on the
motor nameplate. In case of overload, throttle the valve on the
discharge side until the motor is no longer overloaded.
10.4 Motor
The motor should be inspected at regular intervals. It is important
to keep the motor clean in order to ensure adequate ventilation. If
the pump is installed in dusty environments, it must be cleaned
and checked regularly.
10.4.1 Lubrication
Pump bearings
The pump is provided with maintenance-free, greased-for-life
bearings. The pump has no lubricating nipples.
Grease specifications: See 10.4.2 Bearing grease.
Motor bearings
Motors up to and including frame size 160 have maintenancefree, greased-for-life bearings.
Note: At the moment of start, the input current of the pump motor
is up to six times higher than the full-load current stated on the
motor nameplate.
Motors of frame sizes larger than 160 should be greased according to the indications on the motor nameplate. Grease spills from
the motor may occur.
Grease specifications: See 10.4.2 Bearing grease.
9.5 Start/stop
56 - 71
Number of poles
NLGI class 2 or 3.
100
250
350
80 - 100
60
140
160
112 - 132
30
60
80
160 - 180
15
30
50
200 - 225
15
30
Pumps which are not being used during periods of frost should be
drained to avoid damage.
250 - 315
12
Drain the pump by removing the drain plug. See fig. 20.
10. Maintenance
Before starting work on the pump, switch off the supply voltage. It must be ensured that it cannot be accidentally switched on.
10.1 Pump
Do not tighten the priming plug and replace the drain plug until
the pump is to be used again.
Care must be taken to ensure that the escaping liquid
does not cause personal injury or damage to the
motor or other components.
In hot-water installations, special attention should be
paid to the risk of personal injury caused by scalding
hot water.
23
12. Service
If a pump has been used for a liquid which is injurious
to health or toxic, the pump will be classified as contaminated.
If Grundfos is requested to service such a pump, Grundfos must
be contacted with details about the pumped liquid before the
pump is returned for service. Otherwise Grundfos can refuse to
accept the pump for service.
Possible costs of returning the pump are paid by the customer.
pb
Hv
Hs
24
Cause
Remedy
f)
h) Defective bearings.
i)
j)
Defective coupling.
f)
Replace the shaft or the shaft sleeve. Replace the packing in the stuffing box.
25
Fault
Cause
Remedy
d) Pump with bearing seat stressed by the pipe- Mount the pump so that it is not stressed.
work.
Support the pipes.
Check the alignment of the coupling. See 6.2 How to
align the unit.
e) The axial pressure is too high.
Check the relief holes of the impeller and the lock rings
on the suction side.
f)
15. Disposal
This product or parts of it must be disposed of in an environmentally sound way:
1. Use the public or private waste collection service.
2. If this is not possible, contact the nearest Grundfos company
or service workshop.
Subject to alterations.
26
Airborne noise emitted by pumps with MG, MMG, Siemens and TECO motors
50 Hz
2-pole: n = 2900 min-1
4-pole: n = 1450 min-1
6-pole: n = 970 min-1
LpA [dB(A)]
Motor
[kW]
MG
model B
4-pole
0.25
42
0.37
42
MG model C
2-pole
4-pole
MG
model D
2-pole
Siemens
2-pole
4-pole
MMG model E
6-pole
2-pole
4-pole
40
TECO
6-pole
2-pole
51
4-pole
6-pole
58
59
42
40
51
60
58
59
0.75
56
42
43
52
62
58
59
1.1
55
51
59
48
43
52
62
59
59
1.5
58
55
58
48
47
53
64
59
59
0.55
2.2
57
52
60
53
52
57
64
62
59
3.0
59
56
59
53
63
61
65
62
58
4.0
66
59
63
53
63
61
65
63
61
5.5
63
57
63
62
63
61
70
63
60
7.5
73
62
66
63
65
73
62
61
11.0
68
70
66
66
78
67
65
76
69
62
15.0
70
66
66
78
67
65
76
69
65
18.5
70
63
66
78
68
68
76
72
69
22.0
70
63
66
82
68
68
83
72
70
30.0
71
65
59
84
71
68
88
76
74
37.0
71
66
60
84
73
70
88
82
75
45.0
71
66
58
84
73
72
90
82
75
55.0
71
67
58
85
75
72
91
83
81
75.0
73
70
61
86
78
77
91
83
81
90.0
73
70
61
86
78
77
92
85
84
110.0
76
70
61
89
85
77
92
85
84
61
84
132.0
76
70
89
85
93
88
160.0
76
70
92
89
93
90
200.0
76
70
92
89
93
90
250.0
82
73
95
93
95
92
315.0
82
73
95
93
95
94
355.0
77
463
60 Hz
2-pole: n = 3500 min-1
4-pole: n = 1750 min-1
6-pole: n = 1170 min-1
LpA [dB(A)]
Motor
[kW]
MG
model B
4-pole
MG model C
2-pole
0.25
42
45
0.37
42
45
2-pole
Siemens
2-pole
4-pole
MMG model E
6-pole
2-pole
4-pole
40
TECO
6-pole
2-pole
53
4-pole
6-pole
58
59
45
40
53
60
58
59
0.75
57
49
43
54
63
58
59
1.1
60
55
63
52
43
54
63
59
59
1.5
63
53
64
52
47
55
64
59
59
2.2
63
54
65
57
52
59
65
62
59
3.0
71
59
64
57
63
63
66
62
59
4.0
71
61
68
57
63
63
66
63
61
5.5
78
68
67
62
63
63
73
63
60
7.5
78
0.55
464
4-pole
MG
model D
62
66
65
67
74
62
61
11.0
73
70
66
66
80
69
67
76
69
62
15.0
70
66
66
80
69
67
76
69
65
18.5
70
63
66
80
70
70
76
72
69
22.0
70
63
66
84
70
70
83
72
70
30.0
71
65
62
86
73
70
88
76
74
37.0
71
65
63
86
75
72
88
82
75
45.0
75
65
62
86
75
74
90
82
75
55.0
75
68
62
87
77
74
91
83
78
75.0
77
71
66
88
80
79
91
83
80
90.0
77
71
66
88
80
79
90
86
80
110.0
81
75
66
91
87
79
92
88
81
66
81
132.0
81
75
91
87
92
88
160.0
81
75
94
91
92
90
200.0
81
75
94
91
92
91
250.0
97
95
95
93
315.0
97
95
95
95
Max. Q [m/h]
16.2
18.6
21.1
25.0
18.0
21.0
23.9
26.0
21.6
23.8
26.4
27.0
27.2
30.0
33.7
37.0
27.4
29.7
34.4
39.0
28.3
31.5
36.8
41.0
21.2
24.3
28.1
30.0
45.0
46.4
53.8
57.8
59.0
48.0
53.4
59.2
62.0
46.7
53.3
61.0
66.0
51.7
59.6
66.7
67.3
69.0
42.0
47.6
51.4
54.9
76.7
86.1
93.8
100.0
77.7
86.3
98.3
105.0
83.3
95.8
104.5
110.0
85.0
Max. Q [m/h]
10.0
11.6
12.0
8.8
10.5
12.3
13.0
11.5
13.9
14.0
14.5
16.3
18.0
13.2
15.3
18.0
19.0
14.7
16.6
19.6
20.0
11.9
13.9
15.6
16.0
25.3
27.9
30.0
22.4
25.9
29.0
32.0
25.4
29.5
33.1
34.0
28.2
32.8
36.0
24.8
27.7
30.9
32.0
38.9
45.9
50.0
52.0
37.8
41.9
47.9
53.8
55.0
40.6
45.6
56.7
58.0
46.1
52.3
61.0
37.2
42.2
47.5
50.0
Max. Q [m/h]
92.9
103.5
117.0
109.9
118.4
135.8
150.0
120.6
136.1
149.9
158.0
126.3
143.0
159.6
166.0
116.4
139.1
168.3
174.0
159.6
175.3
189.9
200.0
197.3
216.0
244.0
268.0
206.3
229.2
272.2
281.0
181.8
207.9
229.5
248.3
253.0
194.3
209.5
239.0
266.8
302.9
310.0
291.6
316.1
334.0
351.1
379.4
416.0
398.3
450.6
489.2
525.4
533.0
364.1
388.8
446.9
497.3
520.0
353.4
380.6
411.4
480.0
465
466
Max. Q [m/h]
87.9
94.8
109.2
116.0
68.8
75.3
81.1
88.0
86.0
128.6
137.3
150.0
123.0
136.6
153.6
158.0
110.5
125.4
136.5
145.2
163.0
166.0
134.4
146.2
157.2
170.1
174.0
164.3
190.2
207.0
225.0
209.5
233.0
246.0
256.4
272.0
202.4
228.7
251.1
266.8
286.0
224.6
244.1
279.1
300.0
260.4
285.4
308.6
338.1
294.8
334.8
350.0
309.1
328.0
345.7
370.4
410.0
311.4
355.9
379.3
409.0
430.0
369.2
396.4
428.5
471.9
Max. Q [m/h]
63.2
68.0
77.0
59.5
65.8
73.4
81.0
60.1
69.6
78.3
85.0
64.3
72.0
81.1
89.0
75.7
87.2
104.8
110.0
107.7
117.4
127.5
130.0
94.0
106.0
117.2
132.3
137.0
111.0
126.6
144.0
131.8
154.1
169.2
180.0
123.4
134.7
160.3
174.7
189.0
141.1
158.5
175.0
177.1
191.8
212.8
225.0
178.7
200.5
222.4
236.0
195.6
211.3
225.6
248.0
146.6
166.7
185.7
210.3
225.0
243.1
262.9
289.7
300.0
296.4
330.5
Max. Q [m/h]
Max. Q [m/h]
486.0
508.7
548.2
576.6
600.0
473.0
508.6
548.7
595.0
630.0
521.2
556.4
607.0
660.0
917.3
949.6
1000.0
930.0
976.8
1028.4
1100.0
Max. Q [m/h]
Max. Q [m/h]
362.0
384.3
400.0
268.8
287.0
323.0
355.2
360.0
270.5
295.0
322.8
373.1
380.0
265.9
307.6
335.2
367.4
406.7
463.0
433.3
475.3
500.0
494.3
524.0
541.8
588.7
621.7
625.0
593.6
635.7
695.2
787.8
800.0
519.3
585.4
630.7
690.3
757.6
780.0
541.8
583.1
643.6
467
NK, 60 Hz
2-pole: n = 3500 min-1
Pump type
32-125/97
32-125/107
32-125/122
32-125/130
32-125/142
32-125.1/95
32-125.1/104
32-125.1/116
32-125.1/129
32-125.1/140
32-160/128
32-160/139
32-160/152
32-160/168
32-160/177
32-160.1/133
32-160.1/145
32-160.1/156
32-160.1/170
32-160.1/177
32-200/164
32-200/179
32-200/197
32-200/212
32-200/219
32-200.1/158
32-200.1/175
32-200.1/192
32-200.1/207
32-250/207
32-250/227
32-250/242
32-250/256
32-250/262
40-125/110
40-125/118
40-125/131
40-125/140
40-125/142
40-160/131
40-160/143
40-160/162
40-160/177
40-200/178
40-200/193
40-200/206
40-200/216
40-200/219
40-250/193
40-250/206
40-250/215
40-250/236
40-250/252
40-250/260
50-125/105
50-125/113
50-125/124
50-125/140
50-125/144
50-160/127
50-160/141
50-160/154
50-160/165
50-160/177
468
Max. Q [m/h]
29.8
32.1
37.4
40.0
44.0
18.2
20.5
23.6
26.8
30.0
29.3
33.2
38.1
42.2
47.0
19.6
22.6
25.6
29.1
31.0
30.4
34.7
40.8
46.8
49.0
23.2
26.4
29.7
32.0
26.9
30.6
33.2
35.3
36.0
51.0
59.3
61.4
69.7
71.0
52.4
57.9
66.9
74.0
58.7
66.6
72.7
77.8
79.0
60.0
64.8
69.3
76.8
83.0
87.0
70.0
93.3
103.8
116.7
120.0
85.3
96.8
107.9
117.3
126.0
Max. Q [m/h]
11.0
12.9
14.0
12.1
14.3
16.0
12.9
14.7
16.6
17.0
16.7
18.9
21.5
22.0
14.5
17.2
19.8
23.0
16.0
18.7
21.3
24.0
13.2
15.2
17.6
19.0
28.5
31.4
34.0
36.0
25.3
28.6
32.1
35.9
38.0
28.3
32.1
37.4
41.0
31.9
35.1
38.9
43.0
30.1
33.9
38.0
45.9
51.2
57.5
62.0
47.7
52.7
60.5
66.0
51.3
58.8
67.1
70.0
55.2
64.5
73.0
40.6
46.3
53.7
Max. Q [m/h]
111.7
127.6
140.0
128.9
144.3
156.2
173.4
180.0
145.6
162.3
183.1
190.0
156.4
179.5
199.0
126.3
143.4
159.0
176.2
199.0
196.4
210.8
229.3
240.0
237.2
265.0
307.4
322.0
210.1
243.7
274.4
300.7
310.0
215.4
233.1
268.1
295.2
304.0
244.1
266.5
294.1
354.9
370.0
365.5
376.4
401.0
404.7
441.3
466.0
410.5
437.3
495.4
533.0
341.9
386.8
418.5
455.2
502.5
550.0
394.4
447.1
478.6
535.3
566.0
Max. Q [m/h]
92.5
99.5
107.4
121.8
130.8
132.0
107.4
113.9
125.6
139.0
144.0
148.2
157.9
174.0
180.0
137.4
154.9
163.1
173.8
190.0
132.0
140.1
158.4
171.2
186.3
199.0
151.2
164.4
185.4
199.2
209.0
263.4
286.6
302.1
318.9
326.0
244.3
262.4
288.0
324.0
343.0
267.2
287.7
311.1
338.0
360.0
348.2
380.0
408.2
420.0
380.2
415.5
439.0
470.8
492.0
405.4
427.5
455.8
495.1
516.0
498.4
520.8
552.4
578.1
613.2
495.1
Max. Q [m/h]
Max. Q [m/h]
60.0
78.1
84.0
92.0
74.2
83.2
91.7
97.0
75.9
84.8
95.6
102.0
78.2
88.8
102.6
107.0
80.4
96.5
111.1
121.7
132.0
134.4
143.3
156.0
109.7
124.5
139.3
164.0
118.5
138.6
158.2
173.0
155.9
167.5
195.2
213.7
216.0
143.3
158.6
175.1
197.1
222.7
227.0
171.3
193.6
210.0
195.0
213.1
236.6
264.3
270.0
225.4
242.2
257.1
283.0
213.3
241.0
260.2
281.7
298.0
172.9
186.7
204.5
244.8
270.0
303.5
469
470
Max. Q [m/h]
540.6
596.2
650.0
865.5
920.0
950.1
Max. Q [m/h]
326.2
343.7
360.0
351.5
373.8
417.0
453.8
480.0
315.0
339.0
364.6
393.9
430.0
283.8
325.5
352.9
388.0
420.0
338.1
367.5
401.8
449.0
515.1
550.0
540.1
567.1
590.0
580.8
600.8
631.9
668.5
700.0
579.8
647.2
695.3
755.1
800.0
549.0
593.0
636.7
693.9
774.4
825.0
Max. Q [m/h]
NKG, 50 Hz
2-pole: n = 2900 min-1
Pump type
50-32-125.1/100
50-32-125.1/110
50-32-125.1/121
50-32-125.1/140
50-32-160.1/139
50-32-160.1/155
50-32-160.1/169
50-32-160.1/177
50-32-200.1/172
50-32-200.1/188
50-32-200.1/205
50-32-200.1/207
50-32-125/106
50-32-125/115
50-32-125/130
50-32-125/142
50-32-160/139
50-32-160/151
50-32-160/163
50-32-160/177
50-32-200/176
50-32-200/190
50-32-200/206
50-32-200/219
50-32-250/199
50-32-250/219
50-32-250/244
50-32-250/262
65-50-125/105
65-50-125/116
65-50-125/127
65-50-125/139
65-50-125/142
65-50-160/144
65-50-160/158
65-50-160/172
65-50-160/177
65-40-200/172
65-40-200/188
65-40-200/206
65-40-200/219
65-40-250/211
65-40-250/230
65-40-250/245
65-40-250/255
65-40-250/260
65-40-315/273
65-40-315/298
65-40-315/318
65-40-315/336
80-65-125/111
80-65-125/121
80-65-125/135
80-65-125/144
80-65-160/136
80-65-160/150
80-65-160/167
80-65-160/177
80-50-200/181
80-50-200/198
80-50-200/210
80-50-200/219
80-50-250/205
80-50-250/222
Max. Q [m/h]
16.2
18.6
21.1
25.0
18.0
21.0
23.9
26.0
21.6
23.8
26.4
27.0
27.2
30.0
33.7
37.0
27.4
29.7
34.4
39.0
28.3
31.5
36.8
41.0
21.2
24.3
28.1
30.0
45.0
46.4
53.8
57.8
59.0
48.0
53.4
59.2
62.0
46.7
53.3
61.0
66.0
51.7
59.6
66.7
67.3
69.0
42.0
47.6
51.4
54.9
76.7
86.1
93.8
100.0
77.7
86.3
98.3
105.0
83.3
95.8
104.5
110.0
85.0
87.9
Max. Q [m/h]
10.0
11.6
12.0
8.8
10.5
12.3
13.0
11.5
13.9
14.0
14.5
16.3
18.0
13.2
15.3
18.0
19.0
14.7
16.6
19.6
20.0
11.9
13.9
15.6
16.0
25.3
27.9
30.0
22.4
25.9
29.0
32.0
25.4
29.5
33.1
34.0
28.2
32.8
36.0
24.8
27.7
30.9
32.0
38.9
45.9
50.0
52.0
37.8
41.9
47.9
53.8
55.0
40.6
45.6
56.7
58.0
46.1
52.3
61.0
37.2
42.2
47.5
50.0
63.2
Max. Q [m/h]
92.9
103.5
117.0
109.9
118.4
135.8
150.0
120.6
136.1
149.9
158.0
126.3
143.0
159.6
166.0
116.4
139.1
168.3
174.0
159.6
175.3
189.9
200.0
197.3
216.0
244.0
268.0
206.3
229.2
272.2
281.0
181.8
207.9
229.5
248.3
253.0
194.3
209.5
239.0
266.8
302.9
310.0
291.6
316.1
334.0
351.1
379.4
416.0
398.3
450.6
489.2
525.4
533.0
364.1
388.8
446.9
497.3
520.0
353.4
380.6
411.4
480.0
471
472
Max. Q [m/h]
94.8
109.2
116.0
68.8
75.3
81.1
88.0
86.0
128.6
137.3
150.0
123.0
136.6
153.6
158.0
110.5
125.4
136.5
145.2
163.0
166.0
134.4
146.2
157.2
170.1
174.0
164.3
190.2
207.0
225.0
209.5
233.0
246.0
256.4
272.0
202.4
228.7
251.1
266.8
286.0
224.6
244.1
279.1
300.0
260.4
285.4
308.6
338.1
294.8
334.8
350.0
309.1
328.0
345.7
370.4
410.0
311.4
355.9
379.3
409.0
430.0
369.2
396.4
428.5
471.9
486.0
Max. Q [m/h]
68.0
77.0
59.5
65.8
73.4
81.0
60.1
69.6
78.3
85.0
64.3
72.0
81.1
89.0
75.7
87.2
104.8
110.0
107.7
117.4
127.5
130.0
94.0
106.0
117.2
132.3
137.0
111.0
126.6
144.0
131.8
154.1
169.2
180.0
123.4
134.7
160.3
174.7
189.0
141.1
158.5
175.0
177.1
191.8
212.8
225.0
178.7
200.5
222.4
236.0
195.6
211.3
225.6
248.0
146.6
166.7
185.7
210.3
225.0
243.1
262.9
289.7
300.0
296.4
330.5
362.0
Max. Q [m/h]
Max. Q [m/h]
508.7
548.2
576.6
600.0
473.0
508.6
548.7
595.0
630.0
521.2
556.4
607.0
660.0
917.3
949.6
1000.0
930.0
976.8
1028.4
1100.0
1056.7
1144.5
1200.0
Max. Q [m/h]
Max. Q [m/h]
384.3
400.0
268.8
287.0
323.0
355.2
360.0
270.5
295.0
322.8
373.1
380.0
265.9
307.6
335.2
367.4
406.7
463.0
433.3
475.3
500.0
494.3
524.0
541.8
588.7
621.7
625.0
593.6
635.7
695.2
787.8
800.0
519.3
585.4
630.7
690.3
757.6
780.0
541.8
583.1
643.6
725.0
473
NKG, 60 Hz
2-pole: n = 3500 min-1
Pump type
50-32-125/97
50-32-125/107
50-32-125/122
50-32-125/130
50-32-125/142
50-32-125.1/95
50-32-125.1/104
50-32-125.1/116
50-32-125.1/129
50-32-125.1/140
50-32-160/128
50-32-160/139
50-32-160/152
50-32-160/168
50-32-160/177
50-32-160.1/133
50-32-160.1/145
50-32-160.1/156
50-32-160.1/170
50-32-160.1/177
50-32-200/164
50-32-200/179
50-32-200/197
50-32-200/212
50-32-200/219
50-32-200.1/158
50-32-200.1/175
50-32-200.1/192
50-32-200.1/207
50-32-250/207
50-32-250/227
50-32-250/242
50-32-250/256
50-32-250/262
65-50-125/110
65-50-125/118
65-50-125/131
65-50-125/140
65-50-125/142
65-50-160/131
65-50-160/143
65-50-160/162
65-50-160/177
65-40-200/178
65-40-200/193
65-40-200/206
65-40-200/216
65-40-200/219
65-40-250/193
65-40-250/206
65-40-250/215
65-40-250/236
65-40-250/252
65-40-250/260
80-65-125/105
80-65-125/113
80-65-125/124
80-65-125/140
80-65-125/144
80-65-160/127
80-65-160/141
80-65-160/154
80-65-160/165
80-65-160/177
474
Max. Q [m/h]
29.8
32.1
37.4
40.0
44.0
18.2
20.5
23.6
26.8
30.0
29.3
33.2
38.1
42.2
47.0
19.6
22.6
25.6
29.1
31.0
30.4
34.7
40.8
46.8
49.0
23.2
26.4
29.7
32.0
26.9
30.6
33.2
35.3
36.0
51.0
59.3
61.4
69.7
71.0
52.4
57.9
66.9
74.0
58.7
66.6
72.7
77.8
79.0
60.0
64.8
69.3
76.8
83.0
87.0
70.0
93.3
103.8
116.7
120.0
85.3
96.8
107.9
117.3
126.0
Max. Q [m/h]
11.0
12.9
14.0
12.1
14.3
16.0
12.9
14.7
16.6
17.0
16.7
18.9
21.5
22.0
14.5
17.2
19.8
23.0
16.0
18.7
21.3
24.0
13.2
15.2
17.6
19.0
28.5
31.4
34.0
36.0
25.3
28.6
32.1
35.9
38.0
28.3
32.1
37.4
41.0
31.9
35.1
38.9
43.0
30.1
33.9
38.0
45.9
51.2
57.5
62.0
47.7
52.7
60.5
66.0
51.3
58.8
67.1
70.0
55.2
64.5
73.0
40.6
46.3
53.7
Max. Q [m/h]
111.7
127.6
140.0
128.9
144.3
156.2
173.4
180.0
145.6
162.3
183.1
190.0
156.4
179.5
199.0
126.3
143.4
159.0
176.2
199.0
196.4
210.8
229.3
240.0
237.2
265.0
307.4
322.0
210.1
243.7
274.4
300.7
310.0
215.4
233.1
268.1
295.2
304.0
244.1
266.5
294.1
354.9
370.0
365.5
376.4
401.0
404.7
441.3
466.0
410.5
437.3
495.4
533.0
341.9
386.8
418.5
455.2
502.5
550.0
394.4
447.1
478.6
535.3
566.0
Max. Q [m/h]
92.5
99.5
107.4
121.8
130.8
132.0
107.4
113.9
125.6
139.0
144.0
148.2
157.9
174.0
180.0
137.4
154.9
163.1
173.8
190.0
132.0
140.1
158.4
171.2
186.3
199.0
151.2
164.4
185.4
199.2
209.0
263.4
286.6
302.1
318.9
326.0
244.3
262.4
288.0
324.0
343.0
267.2
287.7
311.1
338.0
360.0
348.2
380.0
408.2
420.0
380.2
415.5
439.0
470.8
492.0
405.4
427.5
455.8
495.1
516.0
498.4
520.8
552.4
578.1
613.2
495.1
Max. Q [m/h]
Max. Q [m/h]
60.0
78.1
84.0
92.0
74.2
83.2
91.7
97.0
75.9
84.8
95.6
102.0
78.2
88.8
102.6
107.0
80.4
96.5
111.1
121.7
132.0
134.4
143.3
156.0
109.7
124.5
139.3
164.0
118.5
138.6
158.2
173.0
155.9
167.5
195.2
213.7
216.0
143.3
158.6
175.1
197.1
222.7
227.0
171.3
193.6
210.0
195.0
213.1
236.6
264.3
270.0
225.4
242.2
257.1
283.0
213.3
241.0
260.2
281.7
298.0
172.9
186.7
204.5
244.8
270.0
303.5
475
476
Max. Q [m/h]
540.6
596.2
650.0
865.5
920.0
950.1
1039.3
1100.0
Max. Q [m/h]
326.2
343.7
360.0
351.5
373.8
417.0
453.8
480.0
315.0
339.0
364.6
393.9
430.0
283.8
325.5
352.9
388.0
420.0
338.1
367.5
401.8
449.0
515.1
550.0
540.1
567.1
590.0
580.8
600.8
631.9
668.5
700.0
579.8
647.2
695.3
755.1
800.0
549.0
593.0
636.7
693.9
774.4
825.0
706.6
778.3
850.0
Max. Q [m/h]
NPSH values
50 Hz
Q [l/s]
50-32-160
23-160, 50 Hz
20
10
20
10
10
15
20
25
30 Q [m/h]
Q [l/s]
50-32-250
32-250, 50 Hz
H
[m]
20
10
20
10
4-pole
10
20
30
40
50
10
60 Q [m/h]
15
Q [l/s]
80-65-125
50-125, 50 Hz
H
[m]
60
40
20
2-pole
4-pole
0 10 20 30 40 50 60 70 80
0
10
15
20
25 Q [l/s]
80-50-250
50-250, 50 Hz
H
[m]
8
60
40
60
40
60
80
20
100
30
Q [m/h]
Q [l/s]
10
12
14
Q [l/s]
65-40-250
40-250, 50 Hz
20
10
40
20
10
20
30
40
50
10
60 Q [m/h]
15
Q [l/s]
80-65-160
50-160, 50 Hz
H
[m]
5
40
30
20
10
2-pole
4-pole
0 10 20 30 40 50 60 70 80 90 Q [m/h]
0
10
15
20
25
Q [l/s]
80-50-315
50-315, 50 Hz
H
[m]
40
10
15
20
Q [l/s]
25
30
35 Q [m/h]
10 Q [l/s]
65-50-160
40-160, 50 Hz
4-pole
10
20
30
40
50
10
Q [m/h]
15
Q [l/s]
65-40-315
40-315, 50 Hz
2-pole
4-pole
10
20
30
40
10
50
Q [m/h]
15
Q [l/s]
80-50-200
50-200, 50 Hz
H
[m]
6
50
40
30
20
10
2-pole
4-pole
0 10 20 30 40 50 60 70 80 90 Q [m/h]
0
p
[kPa]
20
2-pole
p
[kPa]
Q [m/h]
10
H
[m]
4-pole
20
50-32-200
32-200, 50 Hz
p
[kPa]
2-pole
16
4-pole
20
10
30
40
80
20
12
40
H
[m]
12
p
[kPa]
4-pole
60
120
Q [l/s]
4-pole
80
16
24 Q [m/h]
6
10
160
2-pole
20
5
65-50-125
40-125, 50 Hz
H
[m]
80
p
[kPa]
10
80
Q [m/h]
16
4
2-pole
p
[kPa]
10
80
20
30
2-pole
12
3
0 5 10 15 20 25 30 35 40 45 50 Q [m/h]
p
[kPa]
5
4
p
[kPa]
8 Q [l/s]
65-40-200
40-200, 50 Hz
H
[m]
40
p
[kPa]
p
[kPa]
8
2
H
[m]
20
2-pole
40
Q [m/h]
2-pole
4-pole
H
[m]
25
p
[kPa]
30
20
50-32-200.1
32-200.1, 50 Hz
10
15
Q [l/s]
20
60
10
0.0
40
30 Q [m/h]
4-pole
25
0.5
30
80
2-pole
20
4-pole
p
[kPa]
10
15
4
3
10
H
[m]
30
4-pole
p
[kPa]
2-pole
1.0
Q [m/h]
10
2-pole
20
4
3
p
[kPa]
16
4-pole
1.5
12
2.0
15
10
2.5
20
10
15
20
25
Q [l/s]
H
[m]
30
50-32-160.1
32-160.1, 50 Hz
H
[m]
100-80-125
65-125, 50 Hz
H
[m]
8
2-pole
60
40
20
2-pole
4-pole
0
0
10 20 30 40 50 60 70
5
10
15
20
Q [m/h]
Q [l/s]
4-pole
0
0
20
40
10
60
30
40 Q [l/s]
p
[kPa]
0.0
20
4-pole
0.5
2-pole
1.0
30
2-pole
p
[kPa]
1.5
50-32-125
32-125, 50 Hz
H
[m]
2.0
10
p
[kPa]
15
50-32-125.1
32-125.1, 50 Hz
H
[m]
p
[kPa]
477
30
40 Q [l/s]
100-65-315
65-315, 50 Hz
40
2-pole
4-pole
0
40
80
120
20
160
200
40
Q [m/h]
60
Q [l/s]
125-80-250
80-250, 50 Hz
H
[m]
8
6
40
20
4-pole
40
40
60
80 Q [l/s]
40
60
40
20
80
100
Q [l/s]
150-125-200
125-200, 50 Hz
60
40
20
2-pole
4-pole
6-pole
0
0
100
200
300
50
400
500
100
Q [m/h]
150
Q [l/s]
200-150-200
150-200, 50 Hz
H
[m]
80
60
40
20
4-pole
6-pole
0 100 200 300 400 500 600 700 800 Q [m/h]
0
478
50
100
150
200
250 Q [l/s]
2-pole
10
8
20
30
Q [m/h]
40
Q [l/s]
125-80-200
80-200, 50 Hz
H
[m]
8
2-pole
40
80
20
40
60
Q [l/s]
125-80-315
80-315, 50 Hz
60
40
20
0
40
80
2-pole
4-pole
p
[kPa]
16
12
4-pole
p
[kPa]
4-pole
H
[m]
120
40
4-pole
0
0
50
20
40
60
80
Q [l/s]
125-100-250
100-250, 50 Hz
H
[m]
80
20
40
60
Q [l/s]
125-100-160
100-160, 50 Hz
H
[m]
10
2-pole
0
0
0
60
40
20
20
40
60
80
Q [m/h]
100
Q [l/s]
150-125-250
125-250, 50 Hz
6-pole
100
200
300
50
400
100
500
Q [m/h]
150
Q [l/s]
80
40
60
80
2-pole
4-pole
6-pole
0
200
50
400
600
Q [l/s]
Q [l/s]
125-100-315
100-315, 50 Hz
H
[m]
12
2-pole
6-pole
4-pole
0
0
0
40
60
80
Q [m/h]
100
Q [l/s]
150-125-315
125-315, 50 Hz
H
[m]
16
2-pole
120
12
80
40
6-pole
4-pole
p
[kPa]
20
12
40
p
[kPa]
200-150-250
150-250, 50 Hz
H
[m]
120
20
4-pole
16
2-pole
160
50
12
80
H
[m]
10
40
6-pole
4-pole
100
80
2-pole
4-pole
6-pole
10
12
4
2
p
[kPa]
16
40
p
[kPa]
12
80
40 Q [l/s]
125-80-160
80-160, 50 Hz
p
[kPa]
80
100
60
Q [m/h]
12
10
p
[kPa]
40
H
[m]
100
4-pole
6-pole
p
[kPa]
30
2-pole
120
2-pole
20
10
8
80
20
10
H
[m]
80
p
[kPa]
10
60
125-100-200
100-200, 50 Hz
H
[m]
60
40
20
40
20
2-pole
80
p
[kPa]
10
60
p
[kPa]
80
p
[kPa]
20
16
12
80
4-pole
10
H
[m]
120
p
[kPa]
60
40
40
20
60
2-pole
20
40
10
80
50
100
150
Q [l/s]
100-65-250
65-250, 50 Hz
H
[m]
200-150-315
150-315, 50 Hz
H
[m]
30
250
25
200
20
150
15
100
10
50
2-pole
4-pole
6-pole
0
200
50
400
600
Q [l/s]
4-pole
60
2-pole
20
p
[kPa]
40
2-pole
100-65-200
65-200, 50 Hz
H
[m]
60
p
[kPa]
p
[kPa]
100-80-160
65-160, 50 Hz
H
[m]
p
[kPa]
40
20
80
p
[kPa]
10
20
30
40
50 Q [l/s]
150-125-500
125-500, 50 Hz
H
[m]
12
80
40
6
4
20
6-pole
0
0
40
60
80
100
Q [m/h]
Q [l/s]
120
4-pole
40
160
4-pole
10
60
p
[kPa]
16
120
12
6-pole
40
10
80
20
120
30
160
40
200
50
Q [m/h]
60
Q [l/s]
200-150-400
150-400, 50 Hz
H
[m]
20
16
4-pole
12
80
40
6-pole
0
0
100
150
200 Q [l/s]
20
160
16
120
12
80
40
4-pole
6-pole
0
0
p
[kPa]
150-125-400
125-400, 50 Hz
H
[m]
40
60
80
100 Q [l/s]
60
100
4-pole
p
[kPa]
200-150-500
150-500, 50 Hz
H
[m]
12
100
10
80
60
40
20
4-pole
6-pole
0
0
100
150
200 Q [l/s]
10
80
125-100-400
100-400, 50 Hz
H
[m]
p
[kPa]
125-80-400
80-400, 50 Hz
H
[m]
p
[kPa]
479
60 Hz
10
15
20
25
6
Q [m/h]
8 Q [l/s]
50-32-160
23-160, 60 Hz
H
[m]
40
40
30
20
10
10 15 20 25 30 35
2
Q [m/h]
10
Q [l/s]
50-32-250
32-250, 60 Hz
30
20
10
4-pole
0
10
2
15
20
25
30 Q [m/h]
Q [l/s]
65-40-200
40-200, 60 Hz
H
[m]
5
40
30
20
10
4-pole
10
20
5
30
40
50
10
60
15
70 Q [m/h]
20 Q [l/s]
80-65-160
50-160, 60 Hz
20
20
10
10
60
20
Q [l/s]
10
15
20
25
Q [m/h]
8 Q [l/s]
65-40-250
40-250, 60 Hz
10
15
20
25
30 Q [l/s]
100-80-125
65-125, 60 Hz
H
[m]
4-pole
0
0
20
30
40
Q [m/h]
Q [l/s]
2-pole
15
20
Q [l/s]
80-50-200
50-200, 60 Hz
4-pole
10
15
20
25
Q [m/h]
30
Q [l/s]
100-80-160
65-160, 60 Hz
H
[m]
10
80
8 Q [l/s]
5 10 15 20 25 30 35 40
2
10
Q [m/h]
12
2-pole
6
4
20
65-50-160
40-160, 60 Hz
60
40
20
50
60 Q [m/h]
15
Q [l/s]
80-65-125
50-125, 60 Hz
4-pole
10
15
20
25
30 Q [l/s]
80-50-250
50-250, 60 Hz
16
2-pole
120
12
80
40
4-pole
20
40
60
10
80
20
Q [l/s]
100-65-200
65-200, 60 Hz
H
[m]
12
60
40
20
20
50 Q [l/s]
10
H
[m]
40
40
40
2-pole
60
30
30
0 10 20 30 40 50 60 70 80 90 100 Q [m/h]
20
20
10
80
10
10
10
H
[m]
80
4-pole
2-pole
100
4-pole
Q [l/s]
40
p
[kPa]
12
100
50-32-200
H
[m]
60
p
[kPa]
2-pole
0 10 20 30 40 50 60 70 80 90100
p
[kPa]
10
10
Q [m/h]
10
H
[m]
0 10 20 30 40 50 60 70 80 90 100 Q [m/h]
10 20 30 40 50 60 70
20
4-pole
4-pole
0
2-pole
2-pole
8
4
Q [m/h]
4-pole
p
[kPa]
12
40
25
2-pole
p
[kPa]
16
20
480
H
[m]
30 Q [m/h]
8
4-pole
40
25
20
2-pole
20
65-50-125
40-125, 60 Hz
40
20
15
4
10
80
10
2
H
[m]
60
40
4-pole
15
2-pole
10
H
[m]
p
[kPa]
10
60
p
[kPa]
30
80
50-32-200.1
32-200.1, 60 Hz
80
p
[kPa]
Q [l/s]
4-pole
0
30
80
H
[m]
60
120
2-pole
80
30 Q [m/h]
40
p
[kPa]
50
25
10
40
40
2-pole
20
20
50
p
[kPa]
6
5
p
[kPa]
H
[m]
50
p
[kPa]
p
[kPa]
15
10
H
[m]
5
4-pole
50
2-pole
0.0
p
[kPa]
50
4-pole
0.5
2-pole
0.0
1.0
4-pole
1.5
10
30
0.5
15
40
2.0
50-32-160.1
32-160.1, 60 Hz
H
[m]
2-pole
4-pole
10
20
30
40
50 Q [l/s]
1.0
20
2-pole
10
2.5
1.5
3.0
25
15
2-pole
p
[kPa]
2.0
50-32-125
32-125, 60 Hz
H
[m]
2.5
20
p
[kPa]
p
[kPa]
50-32-125.1
32-125.1, 60 Hz
H
[m]
p
[kPa]
10
40
Q [l/s]
125-80-250
80-250, 60 Hz
2-pole
40
20
20
40
80
p
[kPa]
10
60
120
20
60
Q [l/s]
125-100-160
100-160, 60 Hz
H
[m]
12
2-pole
2
0
0
40
40
60
80 Q [l/s]
125-100-250
100-250, 60 Hz
H
[m]
12
4-pole
6-pole
0
60
80
100
Q [l/s]
200-150-200
150-200, 60 Hz
H
[m]
16
2-pole
12
8
40
4-pole
6-pole
0 100 200 300 400 500 600 700 800 Q [m/h]
0
p
[kPa]
50
100
150
200
250 Q [l/s]
125-80-400
80-400, 60 Hz
H
[m]
10
80
60
40
20
4-pole
40
10
80
20
120
30
160
40
200
50
Q [m/h]
60
Q [l/s]
150-125-315
125-315, 60 Hz
H
[m]
8
60
40
20
4-pole
6-pole
0
0
40
60
80
100
Q [m/h]
Q [l/s]
20
40
60
80
Q [m/h]
100
Q [l/s]
150-125-200
125-200, 60 Hz
80
40
2-pole
4-pole
6-pole
0
0
50
100
150
Q [l/s]
20
160
16
120
12
80
40
2-pole
4-pole
6-pole
0
200
400
600
100
300
Q [l/s]
125-100-315
100-315, 60 Hz
H
[m]
4
30
20
10
0
40
40
60
80 Q [l/s]
150-125-400
125-400, 60 Hz
80
40
40
20
125-100-200
100-200, 60 Hz
2-pole
4-pole
6-pole
0
0
40
60
80
Q [m/h]
100
Q [l/s]
150-125-250
125-250, 60 Hz
H
[m]
16
2-pole
120
12
80
40
4-pole
6-pole
0
0
50
100
150
Q [l/s]
125-80-315
80-315, 60 Hz
H
[m]
6
50
40
30
20
10
4-pole
0 20 40 60 80 100120140160180 Q [m/h]
0
10
20
30
40
50
Q [l/s]
125-100-400
100-400, 60 Hz
H
[m]
16
120
12
80
40
4-pole
6-pole
0
0
40
60
80
100
Q [m/h]
Q [l/s]
40
p
[kPa]
20
12
80 Q [l/s]
4-pole
6-pole
H
[m]
120
60
6-pole
16
40
4-pole
160
60
p
[kPa]
40
10
80
p
[kPa]
24
200
20
12
100
H
[m]
200-150-250, 60 Hz
H
[m]
40
p
[kPa]
16
12
H
[m]
120
p
[kPa]
10
80
4-pole
6-pole
0
p
[kPa]
12
100
p
[kPa]
p
[kPa]
80
40
120
20
Q [m/h]
p
[kPa]
40
2-pole
10
p
[kPa]
4-pole
TM03 6112 4306
20
80
4-pole
p
[kPa]
16
40
30
H
[m]
80
p
kPa]
20
Q [m/h]
60
40
60
2-pole
4-pole
10
80
80
20
60
Q [l/s]
20
12
4-pole
125-80-200
80-200, 60 Hz
H
[m]
100
80
2-pole
40
10
12
100
60
2-pole
p
[kPa]
125-80-160
80-160, 60 Hz
H
[m]
150-125-500
125-500, 60 Hz
H
[m]
20
160
16
120
12
80
40
4-pole
6-pole
0
0
100
200
50
300
400
100
500
150
Q [m/h]
Q [l/s]
10
80
p
[kPa]
p
[kPa]
100-65-250
65-250, 60 Hz
H
[m]
p
[kPa]
481
8
6
40
20
4-pole
6-pole
0
0
100
150
200 Q [l/s]
200-150-400
150-400, 60 Hz
H
[m]
p
[kPa]
12
100
10
80
60
40
20
4-pole
6-pole
0
0
100
150
200 Q [l/s]
200-150-500, 60 Hz
H
[m]
30
250
25
200
20
150
15
100
10
50
4-pole
6-pole
0 100 200 300 400 500 600 700
0
50
100
150
200
Q [m/h]
Q [l/s]
10
60
482
p
[kPa]
80
200-150-315
150-315, 60 Hz
H
[m]
p
[kPa]
tm
(C)
Hv
(m)
150
140
130
45
40
35
30
25
120
20
110
15
100
12
10
90
80
8,0
6,0
5,0
4,0
70
3,0
60
2,0
40
30
20
10
0
1,5
1,0
0,8
0,6
0,4
0,3
0,2
0,1
50
483
484
485
486
Denmark
France
Mxico
Thailand
GRUNDFOS DK A/S
Martin Bachs Vej 3
DK-8850 Bjerringbro
Tlf.: +45-87 50 50 50
Telefax: +45-87 50 51 51
E-mail: info_GDK@grundfos.com
www.grundfos.com/DK
Argentina
GRUNDFOS GMBH
Schlterstr. 33
40699 Erkrath
Tel.: +49-(0) 211 929 69-0
Telefax: +49-(0) 211 929 69-3799
e-mail: infoservice@grundfos.de
Service in Deutschland:
e-mail: kundendienst@grundfos.de
Netherlands
Turkey
Australia
GRUNDFOS Pumps Pty. Ltd.
P.O. Box 2040
Regency Park
South Australia 5942
Phone: +61-8-8461-4611
Telefax: +61-8-8340 0155
Austria
GRUNDFOS Pumpen Vertrieb Ges.m.b.H.
Grundfosstrae 2
A-5082 Grdig/Salzburg
Tel.: +43-6246-883-0
Telefax: +43-6246-883-30
Belgium
N.V. GRUNDFOS Bellux S.A.
Boomsesteenweg 81-83
B-2630 Aartselaar
Tl.: +32-3-870 7300
Tlcopie: +32-3-870 7301
Belorussia
220090 . 14
: (8632) 62-40-49
: (8632) 62-40-49
Bosnia/Herzegovina
GRUNDFOS Sarajevo
Paromlinska br. 16,
BiH-71000 Sarajevo
Phone: +387 33 713290
Telefax: +387 33 231795
Brazil
GRUNDFOS do Brasil Ltda.
Rua Tomazina 106
CEP 83325 - 040
Pinhais - PR
Phone: +55-41 668 3555
Telefax: +55-41 668 3554
Bulgaria
GRUNDFOS Pumpen Vertrieb
Representative Office - Bulgaria
Bulgaria, 1421 Sofia
Lozenetz District
105-107 Arsenalski blvd.
Phone: +359 2963 3820, 2963 5653
Telefax: +359 2963 1305
Canada
GRUNDFOS Canada Inc.
2941 Brighton Road
Oakville, Ontario
L6H 6C9
Phone: +1-905 829 9533
Telefax: +1-905 829 9512
China
GRUNDFOS Pumps (Shanghai) Co. Ltd.
51 Floor, Raffles City
No. 268 Xi Zang Road. (M)
Shanghai 200001
PRC
Phone: +86-021-612 252 22
Telefax: +86-021-612 253 33
Croatia
GRUNDFOS predstavnitvo Zagreb
Cebini 37, Buzin
HR-10000 Zagreb
Phone: +385 1 6595 400
Telefax: +385 1 6595 499
Czech Republic
GRUNDFOS s.r.o.
apkovskho 21
779 00 Olomouc
Phone: +420-585-716 111
Telefax: +420-585-716 299
Estonia
GRUNDFOS Pumps Eesti O
Peterburi tee 44
11415 Tallinn
Tel: + 372 606 1690
Fax: + 372 606 1691
Finland
OY GRUNDFOS Pumput AB
Mestarintie 11
FIN-01730 Vantaa
Phone: +358-3066 5650
Telefax: +358-3066 56550
Germany
Greece
GRUNDFOS Hellas A.E.B.E.
20th km. Athinon-Markopoulou Av.
P.O. Box 71
GR-19002 Peania
Phone: +0030-210-66 83 400
Telefax: +0030-210-66 46 273
Hong Kong
GRUNDFOS Pumps (Hong Kong) Ltd.
Unit 1, Ground floor
Siu Wai Industrial Centre
29-33 Wing Hong Street &
68 King Lam Street, Cheung Sha Wan
Kowloon
Phone: +852-27861706 / 27861741
Telefax: +852-27858664
Hungary
GRUNDFOS Hungria Kft.
Park u. 8
H-2045 Trkblint,
Phone: +36-23 511 110
Telefax: +36-23 511 111
India
GRUNDFOS Pumps India Private Limited
118 Old Mahabalipuram Road
Thoraipakkam
Chamiers Road
Chennai 600 096
Phone: +91-44 2496 6800
Indonesia
PT GRUNDFOS Pompa
Jl. Rawa Sumur III, Blok III / CC-1
Kawasan Industri, Pulogadung
Jakarta 13930
Phone: +62-21-460 6909
Telefax: +62-21-460 6910 / 460 6901
Ireland
GRUNDFOS (Ireland) Ltd.
Unit A, Merrywell Business Park
Ballymount Road Lower
Dublin 12
Phone: +353-1-4089 800
Telefax: +353-1-4089 830
Italy
GRUNDFOS Pompe Italia S.r.l.
Via Gran Sasso 4
I-20060 Truccazzano (Milano)
Tel.: +39-02-95838112
Telefax: +39-02-95309290 / 95838461
Japan
GRUNDFOS Pumps K.K.
1-2-3, Shin Miyakoda
Hamamatsu City
Shizuoka pref. 431-21
Phone: +81-53-428 4760
Telefax: +81-53-484 1014
Korea
GRUNDFOS Pumps Korea Ltd.
6th Floor, Aju Building 679-5
Yeoksam-dong, Kangnam-ku, 135-916
Seoul, Korea
Phone: +82-2-5317 600
Telefax: +82-2-5633 725
Latvia
SIA GRUNDFOS Pumps Latvia
Deglava biznesa centrs
Augusta Deglava iel 60, LV-1035, Rga,
Tlr.: + 371 714 9640, 7 149 641
Fakss: + 371 914 9646
Lithuania
GRUNDFOS Pumps UAB
Smolensko g. 6
LT-03201 Vilnius
Tel: + 370 52 395 430
Fax: + 370 52 395 431
Malaysia
GRUNDFOS Pumps Sdn. Bhd.
7 Jalan Peguam U1/25
Glenmarie Industrial Park
40150 Shah Alam
Selangor
Phone: +60-3-5569 2922
Telefax: +60-3-5569 2866
New Zealand
GRUNDFOS Pumps NZ Ltd.
17 Beatrice Tinsley Crescent
North Harbour Industrial Estate
Albany, Auckland
Phone: +64-9-415 3240
Telefax: +64-9-415 3250
Norway
GRUNDFOS Pumper A/S
Strmsveien 344
Postboks 235, Leirdal
N-1011 Oslo
Tlf.: +47-22 90 47 00
Telefax: +47-22 32 21 50
Poland
GRUNDFOS Pompy Sp. z o.o.
ul. Klonowa 23
Baranowo k. Poznania
PL-62-081 Przemierowo
Phone: (+48-61) 650 13 00
Telefax: (+48-61) 650 13 50
Portugal
Ukraine
. , 71, . 45
. , 01033, ,
. +380 44 289 4050
+380 44 289 4139
United Kingdom
GRUNDFOS Pumps Ltd.
Grovebury Road
Leighton Buzzard/Beds. LU7 8TL
Phone: +44-1525-850000
Telefax: +44-1525-850011
U.S.A.
Romnia
Usbekistan
700000 . 1-
5
: (3712) 55-68-15
: (3712) 53-36-35
Russia
, 109544 , 39
. (+7) 095 737 30 00, 564 88 00
(+7) 095 737 75 36, 564 88 11
E-mail grundfos.moscow@grundfos.com
Serbia
GRUNDFOS Predstavnitvo Beograd
Dr. Milutina Ivkovia 2a/29
YU-11000 Beograd
Phone: +381 11 26 47 877 / 11 26 47 496
Telefax: +381 11 26 48 340
Singapore
GRUNDFOS (Singapore) Pte. Ltd.
24 Tuas West Road
Jurong Town
Singapore 638381
Phone: +65-6865 1222
Telefax: +65-6861 8402
Slovenia
GRUNDFOS PUMPEN VERTRIEB
Ges.m.b.H.,
Podrunica Ljubljana
Blatnica 1, SI-1236 Trzin
Phone: +386 1 563 5338
Telefax: +386 1 563 2098
E-mail: slovenia@grundfos.si
Spain
Bombas GRUNDFOS Espaa S.A.
Camino de la Fuentecilla, s/n
E-28110 Algete (Madrid)
Tel.: +34-91-848 8800
Telefax: +34-91-628 0465
Sweden
GRUNDFOS AB
Lunnagrdsgatan 6
431 90 Mlndal
Tel.: +46-0771-32 23 00
Telefax: +46-31 331 94 60
Switzerland
GRUNDFOS Pumpen AG
Bruggacherstrasse 10
CH-8117 Fllanden/ZH
Tel.: +41-1-806 8111
Telefax: +41-1-806 8115
Taiwan
GRUNDFOS Pumps (Taiwan) Ltd.
7 Floor, 219 Min-Chuan Road
Taichung, Taiwan, R.O.C.
Phone: +886-4-2305 0868
Telefax: +886-4-2305 0878
96646512 0507
Repl. 96646512 0107
www.grundfos.com
185