Beruflich Dokumente
Kultur Dokumente
Issue Date
01 2012-04-05
Notice
The purchased products, services and features are stipulated by the commercial contract made between Huawei and the customer. All or partial products, services and features described in this document may not be within the purchased scope or the usage scope. Unless otherwise agreed by the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.
Issue 01 (2012-04-05)
Organization
You are advised to read the entire document before upgrading the 3900 Series GSM BTS to V100R012C00SPC058. This document consists of the following chapters: Chapter 1Read-Ahead Information 2Overview of the Upgrade Process 3Upgrade Preparations 4Upgrade Procedure 5Upgrade Verification 6Version Rollback 7FAQ Description Describes the upgrade requirements for this version, compared with the earlier versions. Describes the process of upgrading the earlier version to this version. Describes the preparations that need to be made before the upgrade. Describes the procedures of upgrade operations. Describes how to verify the upgrade. Describes the process of version rollback in the case of an upgrade failure. Provides answers to the frequently asked questions.
Issue 01 (2012-04-05)
iii
Contents
Contents
1 Read-Ahead Information...............................................................1
1.1 Application Scope....................................................................................................................................................1 1.2 Applicable BTS Versions.........................................................................................................................................3 1.3 Impacts of the Upgrade............................................................................................................................................3 1.4 Precautions...............................................................................................................................................................3 1.5 Upgrading Only One Side of a Multi-Mode Base Station.......................................................................................4 1.5.1 Impacts on the Services of the Peer End...........................................................................................................4 1.5.2 Load Control Rights..........................................................................................................................................4
4 Upgrade Procedure......................................................................1
4.1 Obtaining the Site Management Rights...................................................................................................................2 4.2 Setting the Load Control Rights..............................................................................................................................2 4.3 Loading the GTMU Software..................................................................................................................................3 4.4 Loading the UBRI Software....................................................................................................................................5 4.5 Loading the TRX Software......................................................................................................................................6 4.6 Activating the TRX Software..................................................................................................................................6 4.7 Activating the UBRI Software.................................................................................................................................7 4.8 Activating the GTMU Software..............................................................................................................................8 4.9 Releasing the Site Management Rights...................................................................................................................8 4.10 Enabling the Automatic Loading and Activation Function...................................................................................9 Issue 01 (2012-04-05) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd v
Contents
5 Upgrade Verification....................................................................1
5.1 Verification Checklist..............................................................................................................................................1 5.2 Checking the Software Versions of the BTS Boards...............................................................................................1 5.3 Checking the Operating Status of the BTS..............................................................................................................1 5.4 Performing Dialing Tests.........................................................................................................................................2 5.5 Analyzing Traffic Statistics......................................................................................................................................2
6 Version Rollback..........................................................................1
6.1 Precautions...............................................................................................................................................................1 6.2 Rollback Process......................................................................................................................................................1 6.3 Rollback Verification...............................................................................................................................................1
7 FAQ............................................................................................. 1
7.1 How Many Categories of Boards Are There in a BTS?..........................................................................................1 7.2 How to Upgrade the Monitoring Boards?...............................................................................................................2 7.3 How to Enable and Disable the Automatic Loading and Activation Function in Batch Mode?.............................4 7.4 How to Perform an Upgrade in the Case That the Version Before an Upgrade Is BTS3000V100R008C11 and Version of Data Configuration Is SRAN3.0 or Later Versions?.....................................................................................5
vi
Issue 01 (2012-04-05)
1 Read-Ahead Information
Read-Ahead Information
The preceding upgrade guides correspond to different upgrade modes. Figure 1.1 describes the relationship among upgrade guide, upgrade mode, and upgrade scenario. Figure 1.1 Relationship among upgrade guide, upgrade mode, and upgrade scenario Upgrade Guide Upgrad e Mode Upgrade Scenario From V100R008C11 to V100R009 Large-scale BTS upgrade in the commercial network (recommended) Upgrade Scenario from V100R009 to V100R012 NA
3900 Series GSM BTS V100R012C00SPC05 8 Upgrade Guide (V100R008C11 to V100R012, M2000Based).doc
M2000
Issue 01 (2012-04-05)
1 Read-Ahead Information
Upgrade Guide
Upgrad e Mode
Upgrade Scenario from V100R009 to V100R012 Large-scale BTS upgrade in the commercial network (recommended)
3900 Series GSM BTS V100R012C00SPC05 8 Upgrade Guide (V100R009 to V100R012, Within V100R012, M2000Based).doc 3900 Series GSM BTS V100R012C00SPC05 8 Upgrade Guide (SMT-Based).doc
M2000
SMT
Version before an upgrade is BTS3000V100R008C11 and version of data configuration supports SRAN(not recommended)
Local software upgrade in case of emergency Pre-deployment upgrade Local board upgrade in the commercial network
3900 Series GSM BTS V100R012C00SPC05 8 Upgrade Guide (BSC6900 LMTBased).doc GBTS Commissioning Guide
BSC6900 LMT
Version before an upgrade is BTS3000V100R008C11 and version of data configuration supports SRAN(not recommended) NA
USB
The pre-deployment upgrade indicates an upgrade mode in which the BTS software is upgraded in the case that the GTMU is not connected to the BSC. Version of data configuration supports SRAN: indicates that the Is Support Normalized Data Configuration parameter is set to SUPPORT(Support). The upgrade of a BTS from non-SRAN data configuration to SRAN data configuration can be performed on only the M2000.
Select the upgrade guide properly according to the actual upgrade scenario. This document describes the BTS software upgrade from BTS3000V100R009 to BTS3000V100R012 or within BTS3000V100R012 through the SMT.
ii
Issue 01 (2012-04-05)
1 Read-Ahead Information
For a multi-mode base station, SingleRAN3.0 or later can be upgraded directly to the target version whereas versions earlier than SingleRAN3.0 must be upgraded to SingleRAN3.0 first and then to the target version. For the upgrade of SingleRAN3.0 and later versions, check Appendix 1 Version Mapping Information to see whether the source version is a SingleRAN version. You can obtain this appendix from the multi-mode base station release notes in the document package delivered with the software version of the multi-mode base station. Figure 1.2 describes upgrade requirements for SingleRAN versions. For non-SingleRAN versions, contact Huawei technical support for an upgrade policy. Figure 1.2 Applicable BTS versions Version BTS3000V100R008C11 Date If the BTS configuration data is not version SRAN3.0 before the upgrade, this version can be upgraded using the M2000 only. If the BTS configuration data is version SRAN3.0 before the upgrade, this version can be upgraded to BTS3000V100R012C00SPC058 using the M2000, BSC6900 LMT, or SMT. This version can be directly upgraded.
1.4 Precautions
1. 2. 3. The SMT must use the latest software version released with the GBTS software package. The SMT does not support the FTP upgrade mode in BTS3000V100R012C00SPC058 and later. Services are disrupted during the upgrade. Therefore, the upgrade time is based on the customer's requirement.
Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd iii
Issue 01 (2012-04-05)
1 Read-Ahead Information
4. 5.
This document takes the upgrade from BTS3000V100R012C00 to BTS3000V100R012C00SPCXXX of the DBS3900 GSM as an example. The procedure for upgrading the BTS3900 GSM or BTS3900A GSM is the same as that for upgrading the DBS3900 GSM. The subsequent chapters take the DBS3900 GSM as an example to describe the upgrade. During a BTS upgrade, the packages of GTMU software, TRX software, and software of the monitoring boards are involved. The upgrade process of the DRRU, DRFU, GRFU, MRRU, or MRFU is the same as that of the GRRU. The upgrade process of other boards is the same as that of the EMU. This document takes the upgrades of the GTMU, UBRI, GRRU, and EMU as an example. For the list of the boards to be upgraded, see section 7.1"How Many Categories of Boards Are There in a BTS?" You are required to upgrade other boards except the GTMU, UBRI, UTRP and TRX boards according to the precaution released by HUAWEI. The upgrade of other boards should be performed after that of the GTMU, UBRI, UTRP and TRX software. For details, see section 7.2"How to Upgrade the Monitoring Boards?" When the BTS version before an upgrade is BTS3000V100R008C11 and the version of data configuration is SRAN3.0, if you want to perform an SMT-based upgrade, see section 7.4"How to Perform an Upgrade in the Case That the Version Before an Upgrade Is BTS3000V100R008C11 and Version of Data Configuration Is SRAN3.0 or Later Versions". The following modules cannot be upgraded on the SMT: GRFU V2, GRRU V2. If you need to upgrade these modules on the SMT, upgrade them by using the USB flash drive.
6.
7.
8.
9.
10. Only BTS3000V100R012 or later versions support the UTRP. 11. For a multi-mode base station, ensure that the versions of different modes are compatible with each other after the upgrade. If a multi-mode and co-module base station is upgraded mode by mode, the upgrade interval between two modes should not exceed one day.
iv
Issue 01 (2012-04-05)
1 Read-Ahead Information
The load control rights must be given to the other side in a multi-mode base station.
Issue 01 (2012-04-05)
7 FAQ
Perform the upgrade by following the flow chart shown in Figure 1.1. Figure 1.1 Upgrade flow chart
Issue 01 (2012-04-05)
7 FAQ
3
No . 1 2 3 4 5 6 7 8 Item
Upgrade Preparations
Obtaining Reference Documents and Upgrade Software Obtaining Upgrade Tools Disabling the Automatic Loading and Activation Function Connecting the SMT PC to the BTS for Software Upgrade Checking the Software Versions of the BTS Boards Checking the Operating Status of the BTS Backing Up the BTS Software Upgrade Record
7 FAQ
3900 Series GSM BTS V100R012C00SPC058 Upgrade Guide (V100R008C11 to V100R012, M2000-Based).doc 3900 Series GSM BTS V100R012C00SPC058 Upgrade Guide (V100R009 to V100R012, Within V100R012, M2000-Based).doc 3900 Series GSM BTS V100R012C00SPC058 Upgrade Guide (BSC6900 LMTBased).doc 3900 Series GSM BTS V100R012C00SPC058 Upgrade Guide (SMT-Based).doc 3900 Series GSM BTS V100R012C00SPC058 Release Notes.doc
Step 2 Decompress BTS3000V100R012C00SPC058.zip to obtain the BTS3000V100R012C00SP58 folder. Step 3 In the BTS3000V100R012C00SPC058 folder, decompress Download.zip to E:\ BTS3000V100R012C00SPC058 to obtain the board software required for the upgrade. For details about the mapping between BTS boards and board software, see section 7.1"How Many Categories of Boards Are There in a BTS?". ----End
MSs with SIM cards for dialing tests One Ethernet cable Web LMT Maintenance terminal or portable computer installed with the SMT (depressing the upgrade software package and then obtaining the BTSM.zip)
Issue 01 (2012-04-05)
7 FAQ
---End
Step 3 Start the SMT. Choose Maintenance > Communication Parameter. In the Set Communication Port Parameter dialog box, select Network Port under Select Communication Port and set the IP address to 192.168.0.72. Then, click OK, as shown in Figure 1.1.
Issue 01 (2012-04-05)
7 FAQ
Step 4 In the displayed System Login window, enter the User Name and Password, and click Submit, as shown in Figure 1.1. Figure 1.1 System Login window
The default user name is admin and password is admin. Users can log in to the SMT and execute the Set site user password to change the password. ----End
Issue 01 (2012-04-05)
7 FAQ
Step 2 Query and record the GTMU software version. 1. In the displayed Board Management window, right-click the GTMU and then choose Board Information from the shortcut menu. The Board Information dialog box is displayed, as shown in Figure 1.1.
If the Board Management window does not display any board in position, click Refresh(R) in the lower part of the window.
Issue 01 (2012-04-05)
7 FAQ
2. 3.
Step 3 Query and record the TRX software version. 1. 2. In the displayed Board Management window, double-click the GTMU. In the displayed Topology Management window, right-click the RRU/RFU concerned, for example, a GRRU, and then choose Board Information from the shortcut menu. The Board Information dialog box is displayed, as shown in Figure 2.1.
If the Board Management window does not display any board in position, click Refresh(R) in the lower part of the window.
Issue 01 (2012-04-05)
7 FAQ
3. 4. 5.
Record the software version. Click OK. In the Topology Management window, click Close.
Step 4 Query the software version of the monitoring boards. 1. In the displayed Board Management window, right-click the EMU and then choose Board Information from the shortcut menu. The Board Information dialog box is displayed, as shown in Figure 1.1.
Issue 01 (2012-04-05)
7 FAQ
2. 3. 4.
Record the software version. Click OK. In the Board Management window, click Close.
----End
Issue 01 (2012-04-05)
7 FAQ
Step 1 Start the SMT and view the alarms in the lower part of the window. Figure 1.1 Viewing alarms
Step 2 Right-click in the alarm display box, and then choose Save Message from the shortcut menu to save the alarm information. ----End
Recommended method: You are advised to back up the BTS software on the M2000. For details, see the section "Backing Up the BTS Software" described in the 3900 Series GSM BTS V100R012C00SPC058 Upgrade Guide (V100R009 to V100R012, Within V100R012, M2000-Based).
Optional method: If the backup on the M2000 fails, you can visit http://support.huawei.com to download the current BTS software and save it to the local computer.
Issue 01 (2012-04-05)
7 FAQ
4
Step 1 2 3 4 5 6 Operation
Upgrade Procedure
This chapter uses GTMU, GRRU, and UBRI as examples to describe the BTS upgrade procedure on the SMT. Figure 1.2 lists the operations and durations of the BTS upgrade on the SMT. Figure 1.2 Duration of the BTS upgrade in PCK mode Duration 12 minutes 6 minutes 12 minutes 6 minutes 3 minutes 3 minutes
Loading the GTMU Software Activating the UBRI Software Loading the TRX Software Activating the TRX Software Activating the UBRI Software Activating the GTMU Software
The sequence for loading and activating the GTMU and TRX software must be as follows: load GTMU software > load TRX software > activate TRX software > activate GTMU software. If you need to upgrade monitoring boards after upgrading the GTMU and TRX, see section 7.2"How to Upgrade the Monitoring Boards?"
Issue 01 (2012-04-05)
7 FAQ
When the BTS is connected to the BSC, and the site management rights are obtained on the SMT, no configuration command should be run on the SMT because running the configuration command may lead to reset of the BTS. Do not reset a board during the period between loading software to and activating software on the board. ---End
Step 1 On the SMT, click Site255 in the navigation tree in the left pane, and then double-click Software Control under Function in the right pane. In the displayed Software Control dialog box, set related parameters, as shown in Figure 1.1.
To grant the load control right to the GSM side, choose Get Control. To grant the load control right to the LTE or UMTS side, choose Release Control. For details of the ownership of loading control rights, see Appendix 1 Version Mapping Information in the folder MBTS Release Notes.
Effect Software Control: Click Unimmediately Effect SelfVersion: Enter the target GBTS version number BTS3000V100R012C00SP58 PeerVersion: Enter the running version of the peer mode
Issue 01 (2012-04-05)
7 FAQ
Step 2 Click Set. Step 3 Click Query to view the setting results in the Software Control Status field. Step 4 Click Close. ----End
Issue 01 (2012-04-05)
7 FAQ
Step 3 In the displayed Software Download dialog box, set the associated parameters, as shown in Figure 1.1.
File Name: Click Browse, and then navigate to gtmudown.pck. Send Window Size: 200 Version: Select the lower check box under Version and type V100R012C00SP58. File ID: Select GTMU_MAIN from the drop-down list.
Figure 1.1 Setting the parameters for loading the GTMU software
Issue 01 (2012-04-05)
7 FAQ
Step 5 When the progress reaches 100% and a message saying "Loading software successfully"is displayed in the lower left corner of the dialog box, click Close. ----End
When the software loading fails, a message saying "Loading software failed: Software version No. error" may be displayed in the lower left corner of the dialog box, indicating that the software loading fails and the software version has an error. In this case, although the progress reaches 100%, the software is not downloaded to the flash memory of the GTMU actually. You need to verify that the software package is BTS3000V100R012C00SP58.zip.
Load the UBRI software by performing the following steps: Step 1 On the SMT, click Site255 in the navigation tree, and then double-click Forced Software Load under Function. Step 2 In the displayed Software Download dialog box, set the associated parameters as follows:
File Name: Specify the path and name of the target software package required for the upgrade. Send Window Size: 200 Version: Select the lower check box under Version and type V100R012C00SP58. File ID: Select UBRI_MAIN from the drop-down list.
Step 3 Click Start. The software loading starts. Step 4 When the progress reaches 100% and a message saying "Loading software successfully" is displayed in the lower left corner of the dialog box, click Close.
When the software loading fails, a message "Loading software failed: Software version No. error" may be displayed in the lower left corner of the dialog box, indicating that the software loading fails and the software version has an error. In this case, although the progress reaches 100%, the software is not downloaded to the flash memory of the GTMU. You need to verify that the software package is BTS3000V100R012C00SP58.zip. ---End
Issue 01 (2012-04-05) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd 5
7 FAQ
File Name: Specify the path and name of the target software package required for the upgrade. Send Window Size: 200 Version: Select the lower check box under Version and type V100R012C00SP58. File ID: Select GRRU_MAIN from the drop-down list.
When the File ID is set to GRRU_MAIN or MRRU_MAIN, select the mrrudown.pck file in the File Name field. When the File ID is set to GRFU_MAIN or MRFU_MAIN, select the mrfudown.pck file in the File Name field. For details about the mapping between the board software and the file name, see section 7.1"How Many Categories of Boards Are There in a BTS?"
Step 3 Click Start. The software loading starts. Step 4 When the progress reaches 100% and a message saying "Loading software successfully" is displayed in the lower left corner of the dialog box, click Close.
When the software loading fails, a message "Loading software failed: Software version No. error" may be displayed in the lower left corner of the dialog box, indicating that the software loading fails and the software version has an error. In this case, although the progress reaches 100%, the software is not downloaded to the flash memory of the GTMU. You need to verify that the software package is BTS3000V100R012C00SP58.zip. ---End
Issue 01 (2012-04-05)
7 FAQ
under Function. Step 2 In the displayed dialog box, set the associated parameters as follows:
Version: V100R012C00SP58. Board No.: To activate the software of a single GRRU in this step, type the board number of the GRRU in the Board No. box. You can obtain the board number by querying the board attribution. For details, see Step 3 in section 3.6"Checking the Software Versions of the BTS Boards." If no board number is specified, the software of all GRRUs of the BTS will be activated. In the File ID drop-down list, click GRRU_MAIN.
Step 3 Click OK. The software activation starts. Then the status bar displays "Software activation confirmed", as shown in Figure 1.1. Click Close. Figure 1.1 Completing the TRX board software activation
---End
Activate the UBRI software by performing the following steps: Step 1 On the SMT, click Site255 in the navigation tree, and then double-click Software Activation under Function. Step 2 In the displayed dialog box, set the associated parameters as follows:
Version: Type V100R012C00SP58 in the lower box. File ID: Select UBRI_MAIN from the drop-down list. Board No.: You are not required to set this parameter.
Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd 7
Issue 01 (2012-04-05)
7 FAQ
Step 3 Click OK. The software activation starts. Then the status bar displays "Software activation confirmed", click Close. ---End
Version: Type V100R012C00SP58 in the lower box. File ID: Select GTMU_MAIN from the drop-down list. Board No.: You are not required to set this parameter.
Step 3 Click OK. The software activation starts. Step 4 When a message is displayed indicating "Activation is confirmed and the Site will be reset in a few minutes", click Close.
After the software activation is confirmed, it takes three minutes for the services to resume. When the query result shows the new version of the GTMU, you can infer that the GTMU software is activated successfully. For details about how to query the version on the SMT, see section 3.6"Checking the Software Versions of the BTS Boards." ---End
Issue 01 (2012-04-05)
7 FAQ
Before enabling the automatic loading and activation switch, ensure that the BTS3000V100R012C00SP58 software package is uploaded on the BSC6900 LMT. Otherwise, the BSC resets the BTS during the version verification when the automatic loading and activation function is enabled. For details on how to download the BTS software package to the BSC6900 LMT, see section 7.3How to Enable and Disable the Automatic Loading and Activation Function in Batch Mode? Enable the automatic loading and activation function by performing the following steps: Step 1 On the BSC6900 LMT, enter SET BTSAUTODLDACTINFO in the Command Input box, and then click Assist. Step 2 Set the parameters displayed below the Command Input box as follows:
Index Type: select BYNAME(By Name) BTS Name: enter the GBTS name Auto Download Active Function Switch: select ON(ON). Work Mode for Auto Download Activation: select BTSAUTODLDACT. BTS Software Version 1: type BTS3000V100R012C00SP58. Auto Download Mode: based on actual situation
The differences of the loading modes are described as follows:
COMMON_DLD(Normal Mode): The loading does not interrupt services. QUICK_DLD1(Quick Download No Traffic): The loading leads to interruption of cell services under this BTS. QUICK_DLD2(Quick Download Reserve BCCH): The services on the BCCH carrier of cells under this BTS can function normally.
BTS Type: type of the target BTS V-Version No.:100 R-Version No.:012 C-Version No.:00 Patch Number:58
Issue 01 (2012-04-05)
7 FAQ
Step 3 Click Exec. In the output of the MML command, check that the function is successfully enabled. ----End
10
Issue 01 (2012-04-05)
7 FAQ
5
Figure 1.3 Verification checklist No. 1 2 3 4 Item
Checking the Software Versions of the BTS Boards Checking the Operating Status of the BTS Performing Dialing Tests Analyzing Traffic Statistics
Upgrade Verification
Issue 01 (2012-04-05)
7 FAQ
Issue 01 (2012-04-05)
7 FAQ
6
6.1 Precautions
Version Rollback
If the network runs improperly after the upgrade or the KPIs after the upgrade fail to meet the customer's requirements on the day following the upgrade, roll back the version and report the event to Huawei. If both modes of a dual-mode base station are upgraded, it is recommended that you roll back the version of both modes to the original version during the version rollback. You should perform the rollback on the SMT released with the version BTS3000V100R012C00SPC058.
Issue 01 (2012-04-05)
7 FAQ
7
Figure 1.4 FAQ list SN 1 2 3 4 Question How Many Categories of Boards Are There in a BTS? How to Upgrade the Monitoring Boards?
FAQ
How to Enable and Disable the Automatic Loading and Activation Function in Batch Mode? How to Perform an Upgrade in the Case That the Version Before an Upgrade Is BTS3000V100R008C11 and Version of Data Configuration Is SRAN3.0 or Later Versions?
Issue 01 (2012-04-05)
7 FAQ
Categor y
Site Model BTS3900 GSM&BTS3900A GSM 3900 Series GSM BTS 3900 Series GSM BTS 3900 Series GSM BTS BTS3900 GSM&BTS3900A GSM BTS3900 GSM&BTS3900A GSM 3900 Series GSM BTS 3900 Series GSM BTS 3900 Series GSM BTS
File Name mrfudown.pck demudown.pck dpmudown.pck datudown.pck fmudown.pck dheudown.pck uscudown.pck ubridown.pck utrpdown.pck
Monitoring Board
2.
Issue 01 (2012-04-05)
7 FAQ
3.
In the displayed Software Download dialog box, set the associated parameters as follows: File Name: Specify the path and name of the target software package required for the upgrade. Send Window Size: 200. Version: Enter V100R012C00SP58 in the lower box. File ID: Select EMU_MAIN from the drop-down list.
The operations for other monitoring boards are similar to that for the EMU. For details about selecting the file name, see Figure 1.5. Specify File ID based on the actual board type.
4. 5.
Click Start. The software loading starts. When the progress reaches 100% and a message is displayed in the status bar indicating "Loading Software Successfully", click Close.
When the software downloading fails, a message is displayed in the status bar indicating "Loading software failed, Software version No. error." In this case, although the progress reaches 100%, the software is actually not downloaded into the flash memory of the GTMU. You need to verify that the software package is BTS3000V100R012C00SP58.zip. Step 2 Activate the software of the monitoring boards.
Issue 01 (2012-04-05)
7 FAQ
1. 2.
On the SMT, click Site255 in the navigation tree, and then double-click Software Activation in the Function pane on the right. In the displayed Software Activate dialog box, set the associated parameters as follows:
Version: V100R012C00SP58 Board No.: To activate the software of a single board in this step, type the target board number in the Board No. box. You can obtain the board number by querying the board attribution. If no board number is specified, the software of all boards with the same type will be activated. File ID: EMU_MAIN
The operations for other monitoring boards are similar to that for the EMU. You should set the File ID parameter according to the actual board type.
3.
Click OK. The software activation starts. When the activation is successful, click Close.
It takes six minutes from the confirmation of software activation to proper operation of the EMU. When the result of EMU version query on the SMT indicates that the version is the new one, you can infer that the EMU software is activated successfully. For details about how to query the version on the SMT, see section 3.6"Checking the Software Versions of the BTS Boards." ----End
7.3 How to Enable and Disable the Automatic Loading and Activation Function in Batch Mode?
Enable and disable the automatic loading and activation function in batch mode by performing the following steps: 1. 2. On the BSC6900 LMT, click Batch on the upper right corner of the window. The Batch tab page is displayed. Copy the required MML commands to be run in batch mode from the Example.txt file to the command input box. Select All, Step by Step, Breakpoint, or Range according to the actual situation, and then click Go, as shown in Figure 2.1. Messages are displayed, informing you of the execution result.
Exam pl e. t xt
Because the loading and the activation of the software require the user to wait, thus you are advised to select the All mode. The execution modes and their meanings are as follows:
Issue 01 (2012-04-05)
7 FAQ
All: You only need to click Go once. Step by Step: You need to click Go before each MML command is executed. Breakpoint: You can set break points for the execution to control the execution process. Range: You can specify the numbers of MML commands to be executed.
---End
7.4 How to Perform an Upgrade in the Case That the Version Before an Upgrade Is BTS3000V100R008C11 and Version of Data Configuration Is SRAN3.0 or Later Versions?
For the upgrade method, see chapter 4"Upgrade Procedure." Perform the steps described in Figure 1.6. Figure 1.6 Upgrade process in a special scenario Step 1 2 3 4 5 6 7 Action Disabling the Automatic Loading and Activation Function Obtaining the Site Management Rights Loading the GTMU Software Activating the UBRI Software Loading the TRX Software Activating the TRX Software Activating the UBRI Software Duration (For Reference Only) 9 minutes 3 minutes 9 minutes 6 minutes 3 minutes
Issue 01 (2012-04-05)
7 FAQ
Step 8 9 10
Action Activating the GTMU Software Releasing the Site Management Rights Enabling the Automatic Loading and Activation Function
Activation of the TRX software is implemented automatically after activation of the GTMU software. Thus, the service interruption time described in section 1.3"Impacts of the Upgrade" increases by 3 minutes. If the software version before the upgrade is earlier than BTS3000V100R008C11SPC003, set the File Name to gtmuold.pck when you load the GTMU software. If the software version before the upgrade is later than BTS3000V100R008C11SPC003 (including BTS3000V100R008C11SPC003), set the File Name to gtmudown.pck when you load the GTMU software.
Issue 01 (2012-04-05)
A Upgrade Record
Upgrade Record
Site name Version before upgrade Upgrade personnel Upgrade result Check Item Before Upgrade Type of the BTS Location of the BTS to be upgraded Quantity of the BTS to be upgraded Target version Upgrade time and duration allowed by the customer Current version of the SMT Check Item During Upgrade Pre-upgrade check Operating status of the BTS Backing Up the BTS Software Upgrade check Obtaining the Site Management Rights Loading the GTMU Software Result Exception Handling Result Upgrade date Version after upgrade Personnel from the customer organization: Personnel from Huawei:
Issue 01 (2012-04-05)
7 FAQ
Loading the TRX Software Activating the TRX Software Activating the GTMU Software Enabling Automatic Loading and Activation Post-upgrade check Software versions of the BTS boards Operating status of the BTS Dialing tests Traffic statistics analysis
Issue 01 (2012-04-05)