Beruflich Dokumente
Kultur Dokumente
Service Manual
TABLE OF CONTENTS
Page
. Technical Specifications..................1-2 . Safety Instruction, Warning & Notes..........1-3 . DFU Instruction..............................................................................2-1 . Mechanical and Dismantling Instructions........................3-1 . Software Version & Upgrades, Region Code Cha nge............4-1 . Trouble Shooting Chart.. . 5-1 . Wiring Diagram......6-1 . Electrical Diagrams and Print-layouts........7-1 . Packing, Set Mechanical Exploded view & Part list.....8-1 . Revision List..................................................................................9-1
Copyright 2009 Philips Consumer Electronics B.V. Eindhoven, The Netherlands All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.
Version 1.1
PHILIPS
1-2
Accessories supplied Remote control and batteries Audio/Video cables Power plug adaptor User Manual Play media DVD-Video, Video CD/SVCD, Audio CD, CD-R/CD-RW, DVD+R/+RW, DVD-R/RW, DivX-CD, Picture CD, MP3-CD TV standard Number of lines: 625 (PAL/50Hz); 525 (NTSC/60Hz) Play: Multi-standard (PAL/NTSC) Video performance Video DAC: 12 bits, 108 MHz Video output: 1 Vpp ~ 75 ohm Video format Digital compression: DVD/SVCD/VCD/DivX Horizontal resolution: DVD: 720 pixels (50 Hz); 720 pixels (60 Hz) VCD: 352 pixels (50 Hz); 352 pixels (60 Hz) Vertical resolution: DVD: 576 pixels (50 Hz); 480 pixels (60 Hz) VCD: 288 lines (50 Hz); 240 lines (60 Hz) Audio performance DA converter: 24 bits, 192 kHz Frequency response: DVD: 4 Hz - 22 kHz (48 kHz); 4 Hz 44 kHz (96 kHz) SVCD: 4 Hz - 20 kHz (44.1 kHz); 4 Hz - 22 kHz (48 kHz) CD/VCD: 4 Hz - 20 kHz (44.1 kHz) Signal-Noise (1 kHz): > 90 dB (A-weighted) Dynamic range (1 kHz): > 80 dB (A-weighted) Crosstalk (1 kHz): > 90 dB Distortion/noise (1 kHz): > 65 dB MP3: MPEG L3
Audio format Digital: MPEG/AC-3: Compressed digital (16, 20, 24 bits, fs 44.1, 48, 96 kHz) MP3: 96, 112, 128, 256 kbps & variable bit rate, fs 32, 44.1, 48 kHz Analog sound stereo Dolby surround compatible downmix from Dolby Digital multi-channel sound Connections Video output: Cinch (yellow) Audio output (L+R): Cinch (white/red) Digital output: 1 coaxial: IEC60958 for CDDA/ LPCM; IEC61937 for MPEG 1/2, Dolby Digital Main unit Dimensions (w x h x d): 360 x 37 x 209 (mm) Net Weight: approximately 1.3 kg Power Power supply rating: 110 - 240V, 50/60HZ Power consumption: <10 W Power consumption in standby mode: <1 W Laser specication Type: Semiconductor laser InGaAIP (DVD), AIGaAs (CD) Wave length: 658 nm (DVD), 790 nm (CD) Output Power: 7.0 mW (DVD), 10.0 mW (VCD/CD) Beam divergence: 60 degrees
1-2
Accessories supplied Remote control and batteries Audio/Video cables User Manual Play media DVD-Video, Video CD/SVCD, Audio CD, CD-R/CD-RW, DVD+R/+RW, DVDR/-RW, DivX-CD, Picture CD, MP3-CD, USB ash drive TV standard Number of lines: 625 (PAL/50Hz); 525 (NTSC/60Hz) Play: Multi-standard (PAL/NTSC) Video performance Video DAC: 12 bits, 108 MHz Video output: 1 Vpp ~ 75 ohm Video format Digital compression: DVD/SVCD/VCD/DivX Horizontal resolution: DVD: 720 pixels (50 Hz); 720 pixels (60 Hz) VCD: 352 pixels (50 Hz); 352 pixels (60 Hz) Vertical resolution: DVD: 576 pixels (50 Hz); 480 pixels (60 Hz) VCD: 288 lines (50 Hz); 240 lines (60 Hz) Audio performance DA converter: 24 bits, 192 kHz Frequency response: DVD: 4 Hz - 22 kHz (48 kHz); 4 Hz 44 kHz (96 kHz) SVCD: 4 Hz - 20 kHz (44.1 kHz); 4 Hz - 22 kHz (48 kHz) CD/VCD: 4 Hz - 20 kHz (44.1 kHz) Signal-Noise (1 kHz): > 90 dB (A-weighted) Dynamic range (1 kHz): > 80 dB (A-weighted) Crosstalk (1 kHz): > 90 dB Distortion/noise (1 kHz): > 65 dB MP3: MPEG L3
Audio format Digital: MPEG/AC-3: Compressed digital (16, 20, 24 bits, fs 44.1, 48, 96 kHz) MP3: 96, 112, 128, 256 kbps & variable bit rate, fs 32, 44.1, 48 kHz Analog sound stereo Dolby surround compatible downmix from Dolby Digital multi-channel sound Connections Video output: Cinch (yellow) Audio output (L+R): Cinch (white/red) Digital output: 1 coaxial: IEC60958 for CDDA/ LPCM; IEC61937 for MPEG 1/2, Dolby Digital Main unit Dimensions (w x h x d): 360 x 37 x 209 (mm) Net Weight: approximately 1.3 kg Power Power supply rating: 110 - 240V, 50/60HZ Power consumption: <10 W Power consumption in standby mode: <1 W Laser specication Type: Semiconductor laser InGaAIP (DVD), AIGaAs (CD) Wave length: 658 nm (DVD), 790 nm (CD) Output Power: 7.0 mW (DVD), 10.0 mW (VCD/CD) Beam divergence: 60 degrees
1-3
1-4
Warning
1.General . All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD). Careless handing during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential. Available ESD protection equipment: 1) Complete kit ESD3 (small tablemat, wristband, connection box, extension cable and earth cable) 4822 310 10671. 2) Wristband tester 4822 344 13999. . Be careful during measurements in the live voltage section. The primary side of the power supply , including the heat sink, carries live mains voltage when you connect the player to the mains (even when the player is off!). It is possible to touch copper tracks and/or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or components in this area. A lighting stroke and a stripe-marked printing on the printed wiring board, indicate the primary side of the power supply. . Never replace modules, or components, while the unit is on. Notes: Manufactured under licence from Dolby Laboratories. The double-D symbol is trademarks of Dolby Laboratories, Inc. All rights reserved. 2. Laser . The use of optical instruments with this product, will increase eye hazard. . Only qualified service personnel may remove the cover or attempt to service this device, due to possible eye injury. . Repair handing should take place as much as possible with a disc loaded inside the player. . Text below is placed inside the unit, on the laser cover shield:
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN, AVOID EXPOSURE TO BEAM.
1-5
Notes
Lead-Free requirement for service INDENTIFICATION:
Regardless of special logo (not always indicated) One must treat all sets from 1.1.2005 onwards, according next rules. x Important note: In fact also products a little older can also be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this. Due to lead-free technology some rules have to be respected by the workshop during a repair: x Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment. In general use of solder-paste within workshops should be avoided because paste is not easy to store and to handle. x Use only adequate solder tools applicable for lead-free solder alloy. The solder tool must be able o To reach at least a solder-temperature of 400C, o To stabilize the adjusted temperature at the solder-tip o To exchange solder-tips for different applications. x Adjust your solder tool so that a temperature around 360C 380C is reached and stabilized at the solder joint. Heating-time of the solder-joint should not exceed ~ 4 sec. Avoid temperatures above 400C otherwise wear-out of tips will rise drastically and flux-fluid will be destroyed. To avoid wear-out of tips switch off un-used equipment, or reduce heat. x Mix of lead-free solder alloy / parts with leaded solder alloy / parts is possible but PHILIPS recommends strongly to avoid mixed solder alloy types (leaded and lead-free). If one cannot avoid, clean carefully the solder-joint from old solder alloy and re-solder with new solder alloy (SAC305). You will find this and more technical information within the magazine, chapter workshop news. For additional questions please contact your local repair-helpdesk. x x Use only original spare-parts listed in the Service-Manuals. Not listed standard-material (commodities) has to be purchased at external companies. Special information for BGA-ICs: - always use the 12nc-recognizable soldering temperature profile of the specific BGA (for de-soldering always use highest lead-free temperature profile, in case of doubt) - lead free BGA-ICs will be delivered in so-called dry-packaging (sealed pack including a silica gel pack) to protect the IC against moisture. After opening, dependent of MSL-level seen on indicator-label in the bag, the BGA-IC possibly still has to be baked dry. This will be communicated via AYS-website. Do not re-use BGAs at all. For sets produced before 1.1.2005, containing leaded soldering-tin and components, all needed spare-parts will be available till the end of the service-period. For repair of such sets nothing changes. x On our website: www.atyourservice.ce.Philips.com You find more information to: BGA-de-/soldering (+ baking instructions) Heating-profiles of BGAs and other ICs used in Philips-sets
DVP3300/93 QSG:
2-1 The following excerpt of the Quick Start Guide serves as an introduction to the set. The complete Direction For Use can be download in different languages from Philips Customer Contact & Support site: www.p4c.philips.com
DVP3300
www.philips.com/welcome
Warning Riskofoverheating!NeverinstalltheDVDplayerinaconnedspace.Always
leaveaspaceofatleastfourinchesaroundtheDVDplayerforventilation.Ensure thecurtainsorotherobjectsnevercovertheventilationslotsontheDVDplayer. NeverplacetheDVDplayer,remotecontrolorbatteriesnearnakedamesor otherheatsources,includingdirectsunlight. OnlyusethisDVDplayerindoors.KeepthisDVDplayerawayfromwater, moistureandliquid-lledobjects. NeverplacethisDVDplayeronotherelectricalequipment. KeepawayfromthisDVDplayerduringlightningstorms. Wherethemainsplugoranappliancecouplerisusedasthedisconnectdevice, thedisconnectdeviceshallremainreadilyoperable. Visibleandinvisiblelaserradiationwhenopen.Avoidexposuretobeam.
DVDdDVD
EN
ZH_CN
ZZZSKLOLSVFRPVXSSRUW
2-2
1
AUDIO OUT L/R & VIDEO OUT
2
DIGITAL IN
DivX
English
z
: :
DVD
2-3
DVP3111/55:
Product overview
Main unit
a
a
c de f
b Disc compartment c Indicators d IR sensor Remote sensor. e f Start, pause or resume disc play. Open or close the disc compartment.
2-4
Remote control
u a b c
(Previous/Next) Skip to the previous or next title, chapter, or track. Press and hold for fast-backward or fast-forward search.
h ANGLE Select a viewing angle of a DVD. Switch veiwing modes during playing JPEG slideshow. i ZOOM Zoom into or out of an image. j MUTE Mute or restore audio output.
t s
d e f g
r q p o n m
k STEP Play video frame by frame. l SLOW Select a slow forward. m REPEAT A-B Repeat a specic section within a track/disc. n REPEAT Select or turn off repeat mode. o STOP Stop play. p PLAY/PAUSE Start, pause or resume disc play q SUBTITLE Select a subtitle language for video.
h i
MUTE
j k l
r AUDIO Select an audio language or channel. s DISC MENU Access or exit the disc menu. For VCD 2.0 and SVCD, turn on or off the PBC (playback control) mode. t RETURN/TITLE Returns to the previous menu. For DVD, navigates to title menu. For VCD version 2.0 or SVCD with PBC turned on, returns to the menu. u OPEN/CLOSE Open or close the disc compartment.
b DISPLAY Display the current play status or disc information c Numeric Keypad 0 - 9 Select an item to play. d SEARCH Start playback from designated point. e SETUP Access or exit the setup menu. f (Navigation buttons) Navigate through the menus. Search fast-forward (right) or fastbackward (left). Search slow-forward (up) or slowbackward (down).
2-3
DVP3300/93:
Product overview
Overview of the main unit
a b c
a
a
c defg
t s
d e f g
b Disc compartment c Indicators d e f (Open/Close) Open or close the disc compartment. (Play/Pause) Start, pause or resume disc play. (USB jack) Connect a USB ash drive.
r q p o n m
h i j k l
Remote control
a b Display the current play status or disc information. Turn on the DVD player or switch to standby mode.
2-4
c Numeric Keypad 0 - 9 Select an item to play. d e f g h i j k l m n o p Start, pause or resume disc play Stop play. Select or turn off repeat mode. Select a slow forward. A-B Repeat a specic section within a track/disc. Play video frame by frame. Select USB device source. Zoom into or out of an image. Select a viewing angle of a DVD. Switch veiwing modes during playing JPEG slideshow. / Access or exit the setup menu. (Navigation buttons) Navigate through the menus. Search fast-forward (right) or fastbackward (left). Search slow-forward (up) or slowbackward (down). OK Conrm an entry or selection. (Previous/Next) Skip to the previous or next title, chapter, or track. Press and hold for fast-backward or fast-forward search. Start playback from designated point.
q r s t u Open or close the disc compartment. Select an audio language or channel. / Access or exit the disc menu. For VCD 2.0 and SVCD, turn on or off the PBC (playback control) mode. / Returns to the previous menu. For DVD, navigates to title menu. For VCD version 2.0 or SVCD with PBC turned on, returns to the menu. Select a subtitle language for video.
2-3
DVP3300X/96
Product overview
Overview of the main unit
a b c
a
a
c defg
t s
d e f g
b Disc compartment c Indicators d iR sensor Remote sensor. e f g (Open/Close) Open or close the disc compartment. (Play/Pause) Start, pause or resume disc play. (USB jack) Connect a USB ash drive.
r q p o n m
h i
USB
j k l
b DISPLAY Display the current play status or disc information c Numeric Keypad 0 - 9 Select an item to play. d SEARCH Start playback from designated point.
2-4
e SETUP Access or exit the setup menu. f (Navigation buttons) Navigate through the menus. Search fast-forward (right) or fastbackward (left). Search slow-forward (up) or slowbackward (down).
t RETURN/TITLE Returns to the previous menu. For DVD, navigates to title menu. For VCD version 2.0 or SVCD with PBC turned on, returns to the menu. u OPEN/CLOSE Open or close the disc compartment.
OK Conrm an entry or selection. g / (Previous/Next) Skip to the previous or next title, chapter, or track. Press and hold for fast-backward or fastforward search.
h ANGLE Select a viewing angle of a DVD. Switch veiwing modes during playing JPEG slideshow. i ZOOM Zoom into or out of an image. j USB Select USB device source. k STEP Play video frame by frame. l SLOW Select a slow forward. m REPEAT A-B Repeat a specic section within a track/disc. n REPEAT Select or turn off repeat mode. o STOP Stop play. p PLAY/PAUSE Start, pause or resume disc play q SUBTITLE Select a subtitle language for video. r AUDIO Select an audio language or channel. s DISC MENU Access or exit the disc menu. For VCD 2.0 and SVCD, turn on or off the PBC (playback control) mode.
3-1
Figure 1
Step2: If it is necessary to dismantle Loader or Front Panel, the Front door should be removed first. (Figure 2) Note: Make sure to operate gently otherwise the guider would be damaged.
Figure 2
3-2
Figure 3 Step4: Dismantling Front Panel, disconnect the connectors (XP3), need release 4 snaps of Front Panel and 2 snaps of bottom cabinet , then gently pull the Panel out from the set. (Figure 4 - Figure 6)
XP9
XP3
Figure 4
3-3
Figure 5 Step5: Dismantling Loader, disconnect the 3 connectors (XP7, XP8, XP9 ) aiming in the below figure, and remove 1 screw that connects the loader and the bottom cabinet. (Figure 5 & 6)
Figure 6
3-4
Figure 7
4-1
Software upgrade
How to upgrade the software 1) Burn the data onto a blank CD-R or RW disc. 1) 2) A. Procedure for software upgrade: CDR. 2) The set will starts reading disc & response with the following display TV screen: Loading Firmware Upgrade Erase and program. B. Read out the Firmware version to confirm the upgrading Power on the set and Open the tray door. Press <9><6><6>button to check the software information. The software version and other information are displayed on the TV screen as follows: BE Version: DVP33XX_XX.XX FE Version: XXXX.XXXXXX DSP Version: DSP.XX Region Code: X
OK
3)
Cancel
Select OK to start upgrade. Press <OK> button to confirm, then screen will
display : Firmware Upgrade Programming, Please Wait... Do not Switch the Player Off ! 4) The upgraded disc will automatically out when files coping complete, then take out the disc. 5) About 1 minute later, the tray will automatically close when upgrading complete.
Caution: The set must not be power off during upgrading, Otherwise the Main board will be damaged entirely.
1) Power on the set and open the tray door; 2) Press "9" "8" "7" "9" and press the region code number (0-6) on the remote control.
5-1
Spindle motor does not move Motor no move
Go
No
Correct connection
Yes
No
Check supply
the
RFA5V
power
Yes
Check whether laser voltage (2.3V for DVD & 1.9V for CD) on Collector of Q4 and Q5
No
Check/Replace Q4Q5.
Yes
1.Whether voltage on pin 97 of U2 varies between 0 and 3.3V (3.3V for CD and 0V for DVD), 2.Whether peripheral components are eroded or badly soldered.
Yes 1. Have no focus No Check U2 pin89 FOCUS_PWM signals 2.If there are F+, F-, T+ and Tsignals output from U4. Yes FOCUS_PWN waveform Check/Replace the loader
5-2
The power can not be on or off
The power cant be on or off Go
No
Yes
Yes
No
Check/Correct connection
Yes
Check
if
the
xp1
on
the
Yes
Yes
Yes Replace F1
No
No
Yes
Yes
No
Yes Check whether the components in the short-circuit voltage are defected or eroded.
5-4
Disc cannot be read.
Yes
Yes
1.Check voltage on pin 97 of U2 varies between 0 and 3.3V: Check whether there is laser voltage (2.3V for DVD and 1.9V for CD) on Collector of Q4 &Q5
No
3.3V for CD 0V for DVD 2.Check whether peripheral components are eroded or defect
Yes
Check
U2,
U4,
and
Yes
Check if there is RFO signal on pin10 of XP7. (The normal RFO signal is a clear reticulated wave)
No
Yes
No
Correct connection
Yes
Replace U2 or loader.
5-5 Only DVD disc or only disc except DVD can be played
Go
No
Yes
Yes
No
Yes
Check whether pins of U2 and peripheral components are badly soldered, defected
5-6
No display on LED, and buttons do not work
No display on LED, and buttons do not work Yes
No
Correct connection
Yes
No
Fix power supply board top a power supply for should electric circuit
Yes
Check there are CS, DATA and CLK signals on XS301 on the front board.
No
Check the U2s pin 48,95,96 arrive the XP1 connect condition
XP1 (PIN 1 CLK) XP1 (PIN3 DOUT)
Yes
1.Check whether bad solder exists on Q302,Q303 and pins of LEDS, 2.Check whether the circuit connected to K301,K302,is broken, 3.Check whether R303,R304,R302 are open-circuit.
No
Correct connection
5-7
Distorted audio and loud noise
Distorted audio and loud noise Yes
No
Check whether the output of the power board is normal.If abnormal ,change the power board
Yes
No
Yes
Check muting
whether
the
No
transistor
Yes
No
&RUUHFWFRQQHFWLRQ
Yes
No
Check whether the U7 or U8 powersupply normal
Check U7,U8
Yes
Replace U7 or U8
5-8
Abnormal color of video picture
Check
whether
the
Yes
Check whether the 3.3V and 1.8V power supply voltages on the decoder board are normal.
Yes
No
Yes No Change U2
5-9
Remote reception is insensitive or fails.
Check battery
Yes
No Check L2
Yes
Use an oscilloscope to check if there is output waveform from the first pin IR of the remote censor after pressing button on the remote control.
No
IR600 (PIN1 - RC waveform)
Yes
IR waveform
No
Correct connection
5-10
No video picture, no sound.
Check whether all the voltages from the power board to the decoder board are normal.
Yes
Check if the reset circuit consisting of CE3, D6 and R21 is normal (at a high level for tens of milliseconds, then constantly at 3.3V).
27Mhz waveform
No
Yes
No
Yes
No
Check U2.
Yes Yes
6-1
A B C D
6-1
E
DVD LOADER
24
VIDEO LPF&DRIVE
C
XP7 24PIN*0.5
6 1
XP9 5PIN*2.0
CD5888
6PIN*2.0 XP8
1 1
16M SDRAM
ZR36966/XF2
1
+5V +5V GND +12V GND
POWER SUPPLY
CON2 (1-5PIN) 5PIN*2.5
XP2 (1-5PIN)
MOTER DRIVER
5
5PIN*2.5
6
IR 5V GND DATA CS CLK POWER_K PLAY_PAUSE OPEN/CLOSE
4
DP
USB
1
USB 5V
DN
GND
LED+
LED-
9
XS302 4PIN*2.0 XS301 9PIN*2.0
7
XP601
POWER+ POWER-K
FB BOARD
USB AND O
BOARD
7-1
A B C D
7-1
E
)5200$,1%2$5'
R311 XS301 R312 R313 R314 R315
9 8 7 6 5 4 3 2 1
9PIN/2.0mm
10K
10K
10K
10K
C302 0.1u
VCC
5 4
OPEN/CLOSE PLAYER/PAUSE
5 4
REM
VCC GND IR
3 2 1
IR + C303 0.1u
100 ohm
CE300 47uF
VCC
R305 470
R306 470
R310 100
ON orange PLAY green LED2 R316 R317 NC/0R 10MA NC/0R 10MA LEDQ302 8550 CE200 22uF/NC D301 LED_PLAYER C306 C307 NC/0.1U NC/0.1U Q303 8550 LED_Standby 1N4148 5MA LED3 standby RED LED+
1 2 3 4
XS302 CON4(2.0)
C316 100p
C308 100p
C309 100p
7-2
A B C D
7-2
E
K304
POWER
1 2 3 4
XP1 CON4(2.0) C319 47p
SWITCH
BOARD
7-3
1 2 3 4
7-3
5
P800 USB
1 2 3 4 5 6
VCC
1 2 3 4
1 2 3 4
USB00 USB
XS800 4PIN/2.0mm
7-4
A B C D
7-4
E
F1 T2AL/250ac P3
C N1
+
CON1 AC INPUT RV1 10K471 D3 1N4007 D4 1N4007
P2
C5 152/1KV
R2 R3 1/4W120K 1/4W120K
6 7
2
D8 IN4007 C9 104/50V
3
R4
D7 FR102
C6 47uF/25V 1/6W10k
8 1
D10 SR360/SR340 C14 NU + C7 1000uF/16V L2 6.8uH + C8 470uF/16V R5 1/6W12K 1%
12
R11
11 10
R1 NU
BP/M
NC
U1 TNY176/177
EN/UV
Drain
1/6W22
U2 PC123X92
1 2
U3 TL431 R7 1/6W11.3k 1%
3
CY1 102/400Vac
* CAUTION :
THE PARTS MARKED WITH ARE IMPORTANT PARTS ON THE SAFETY. PLEASE USE THE PARTS HAVING THE DESIGNATED PARTS NUMBER WITHOUT FAIL.
AC INPUT
AC INPUT
L6
T1
6 5 4 3 2 1
7-4
7-4
F1 T2AL/250ac P3
1
AC INPUT
2
CN1 AC INPUT
+ D3 D4 1N4007 1N4007
R6 1/6W1K(NU)
+ C2 15uF/400V(250V/450V)
C1 10uF/400V(250V/450V)
P2
L6
T1
C5 152/1KV
R2 R3 1/4W120K 1/4W120K
6 7
2
D8 IN4007 C9 104/50V
3 9
D7 FR102 + C6 47uF/25V
8 1
D10 SR360/SR340 C14 NU + C7 1000uF/16V L2 6.8uH + C8 470uF/16V R5 1/6W12K 1%
12
R11
11 10
R1 NU
U1 TNY176/177
EN/UV
BP/M
Drain
NC
1/6W22
U2 PC123X92
CY1 102/400Vac
* CAUTION :
U3 TL431
1
R7 1/6W11.3k 1%
PLEASE USE THE PARTS HAVING THE DESIGNATED PARTS NUMBER WITHOUT FAIL.
R4 1/6W10k
6 5 4 3 2 1
7-5
A B C D
7-5
E
220uF/16V
1
VSCK VSTB VSDA L2 R3 OPEN/CLOSE PLAY_PASUE POWER_K VSCK VSTB VSDA NC/500 33R M5V IR Y_R_V Y_R_V L3 C3 150pF 0R C4 150pF V_OUT
OPEN/CLOSE PLAY/PAUSE POWER_K CLK LED_ON CS LED_PLAYER LED_standby DAT GND LED_5V IR
1 2 3 4 5 6 7 8 9
I a
IR
0 A
CVBS_G_Y
CVBS_G_Y
L4 C11 150pF
0R C12 150pF
Y_OUT
C8 C7 C6 C5 C95 C96 C97 C10 100pF 100pF 100pF 0.1uF 0.1uF 0.1uF 0.1uF 100p
C_B_U
C_B_U
L6 C14 150pF
0R C15 150pF
U_OUT
U11
V_OUT
1 2
6 5 4
RCA_CVBS_OUT
2
P1 RCA/AUDIO OUT
U_OUT M5V
Y_OUT
PESD3V3L5UY
TO POWER BOARD
I a
XP2
00 A
RFA5V
RFA5V
I a
M5V C13 10nF
A
1 1 1
1 2 3 4 5 6
C18 47pF
RCA RCA151 1
PESD5V0S(L)1BA
PESD5V0S(L)1BA
PESD5V0S(L)1BA
5PIN/2.5mm
0 A
PESD5V0S(L)1BA
1 2 3 4 5
+P12V
D9
D10
D11
D12
DSPVCC33 R6
R12 22K
R13 4.7K
C88 0.1uF
RCA_CVBS_OUT
RCA_CVBS_OUT
3
PCON
4.7K R7 Q2 BT3904
3
4.7K
7-6
A
RESET Circuit
DSPVCC33I INSW DRVSB IN_OUT_SW CLOSE OPEN HOMESW
7-6
B C D
Important power supply! URST#
R99 22k Q14 2N3904 + R102 4.7k CE19 10uF/16v CEL5-5 C89 1uF 1 0MA L7 VDDAFE 500 C20 10nF RF C24 33pF RF 1 5MA L8 VDDDAC 500 C26 10nF VFE_YIN RF_F SPDL_SENS+ RF_E SPDL_SENSRF_D RF_C C27 0.1U MA RF_B RF_A VDDPLL C29 0.1U VDDAFE R18 4.7 DSPVCC18 DSPVCC33 C21 0.1U D8 NC/1N4148 R100 1k RESET# R101 3.3k Q13 1MA R14 C19 10nF + CE2 100U/16V 4.7 DSPVCC33
VDDPWM
R97 15k
R98 3.3k
2N3904
1
FOCUS_PWM TRACK_PWM LD_DVD LD_CD MD_DVD MD_CD
Close to Vaddis!
DSPVCC33
C22 C23 15.4K 1% 0.1uF VFE_YIN RF_F SPDL_SENS+ RF_E SPDL_SENSRF_D RF_C RFN RFP
1nF 1nF
I a
INSW IN_OUT_SW R16 R17 1K 1K VSTB
0 A
VSTB
CLOSE HOMESW
VDDPWM
VDDAFE
RESOUT VREF VC
R15 C25
1 2 3 4
8 7 6 5
R19
DSPVCC18 DSPVCC33I C9
R22 4.7K MUTE_CTL SFCS SFCLK SFDO SFDI SFCLK R85 SFCLK_0 33R PLAY_PASUE POWER_K OPEN/CLOSE MUTE_CTL
Gen_5/GPIO[0] Gen_6 VDDP Gen_7 Gen_8 Gen_9 Gen_11 Gen_12/VID0 VDDC GPIO[52]/PWMCO[3]/HSYNC GPIO[51]/PWMCO[2]/FIELD GPIO[50]/PWMCO[1]/VCLKx2 VDDPWM GPIO[49]/PWMCO[0] DVD_LD CD_LD DVD_MD CD_MD VDDSAFE GNDREF RESOUT VREF VC GND1AFE VFE_YIN F K E J D C VDDAFE B A VDD1AFE RFN RFP GNDDACBS2
HOLD HYPER
DSPVCC33
U2A
0.1U
VDDAFE
RF_B RF_A
SPDL_PWM SLED_PWM
VC
ad
OSCIN OSCOUT VDDPLL RESET# IR DUPRD0/VSDA S/PDIF_OUT GP-0 GP-1 GP-4 GP-5
XP11
R104 USB_DP USB_DN USB5V R106 C90 15K/NC 0.1U 47P 15K/NC 47P C91 R107 R105 C92
24R/NC
4 3 2 1
4PIN/2.0mm
24R/NC
Vaddis-966XE/XF
RAMADD[0] RAMADD[8] RAMADD[10] VDDP RAMADD[9] RAMADD[11]/GPO[64] RAMCS0# RAMBA RAMCS1#/GPO[65] RAMRAS# RAMCAS# VDDP RAMWE# RAMDQM GNDPCLK PCLK VDDPCLK RAMDAT[8] RAMDAT[7] RAMDAT[9] RAMDAT[6] RAMDAT[10] RAMDAT[5] RAMDAT[11] RAMDAT[4] RAMDAT[12] RAMDAT[3] VDDIP RAMDAT[13] RAMDAT[2] VDDC RAMDAT[14] RAMDAT[1] RAMDAT[15] RAMDAT[0] VDDP GNDAPWM VDDAPWM
Down load
103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128
Gen_4/VID7 SFCS GND SFDO/RS_SF SFDI/RS128_Bootsel2 VDDC VDDP SFCLK/RS128_Bootsel1 GPIO[5] SD_D/IGPIO[7] PWM5 SD_CMD/GPIO[6] SD_CLK/IGPIO[7] VDDP DP DN RAMADD[4] RAMADD[3] RAMADD[5] VDDIP RAMADD[2] RAMADD[6] RAMADD[1] RAMADD[7] VDDC GND
RSET DAC1 VDDDAC DAC2 DAC3 VDDDAC DAC4 GNDC XIN XO VDDPLL GNDPLL RESET# VDDC VDDP IGPIO[44] GPIO[43]/DUPRD0/TDO/SSCTXD GND GPIO[32]/SPDIFO VDDP GPIO[29]/AMCLK/APWM0GPIO[28]/APWM1GPIO[26]/APWM2GPIO[25]/AOUT2/APWM3GPIO[24]/DUPRD1/ALRCLK/APWM4IGPIO[23]/DUPTD1/ABCLK/APWM5-
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39
Close to Vaddis
2
C_B_U Y_R_V CVBS_C C_B_U Y_R_V CVBS_C CVBS_G_Y
R30
100
C31
33pF
Crystal
R28 220K
Y2 27.000MHz
OSCIN
C33
33pF
M5V F1 [FUSE(500MA)]
D1 1
MBRX120 2USB5V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
DSPVCC33
XP5 4PIN/2.0mm
1 2 3 4
DUPTD0 DUPRD0
RAMDAT8 RAMDAT7 RAMDAT9 RAMDAT6 RAMDAT10 RAMDAT5 RAMDAT11 RAMDAT4 RAMDAT12 RAMDAT3
RAMDAT13 RAMDAT2
RAMADD9
RAMRASRAMCAS-
IPCLK
RAMWERAMDQM
RAMCS0RAMBA
VDDAPWM . 0V
D
DSPVCC33
ad
RAMADD11
CE4 470uF/6.3V
RAMCS1-
XP6 4PIN/2.0mm
WARNING
DRC000
N t
as
t an t
1 5.10
1 5.
GP-5 GP-4
Close to Vaddis
RAMDAT10 RAMDAT11 RAMDAT12 RAMDAT13 RAMDAT14 RAMDAT15 RAMDAT15 RAMDAT14 RAMDAT13 RAMDAT12 RAMDAT11 RAMDAT10 RAMDAT9 RAMDAT8 RAMDAT9 RAMDAT8 RAMADD4 RAMADD5 RAMADD6 RAMADD7 RAMADD8 RAMADD9 RAMCKE PCLK RAMDQM RAMDQM PCLK RAMCKE
Close to pin 38
1 2 3 4
DUPTD1 DUPRD1
DSPVCC18 DSPVCC18 C36 0.1U C37 0.1U C38 0.1U C39 0.1U C40 0.1U
SDRAM3V3
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
SDRAM3V3
DSPVCC33
U3
VSS A4 A5 A6 A7 A8 A9 NC CKE CLK UDQM NC VDDQ DQ8 DQ9 VSSQ DQ10 DQ11 VDDQ DQ12 DQ13 VSSQ DQ14 DQ15 VSS
16Mbit: K4S161622C-TC/L70
VDD A3 A2 A1 A0 A10/AP BA CS RAS CAS WE LDQM VDDQ DQ7 DQ6 VSSQ DQ5 DQ4 VDDQ DQ3 DQ2 VSSQ DQ1 DQ0 VDD
U10
4
DSPVCC33
VDD DQ0 VDDQ DQ1 DQ2 VSSQ DQ3 DQ4 VDDQ DQ5 DQ6 VSSQ DQ7 VDD DQML WE# CAS# RAS# CS# BA0 BA1 A10 A0 A1 A2 A3 VDD
C41 0.1U
VSS DQ15 VSSQ DQ14 DQ13 VDDQ DQ12 DQ11 VSSQ DQ10 DQ9 VDDQ DQ8 VSS NC DQMH CLK CKE NC A11 A9 A8 A7 A6 A5 A4 VSS
54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28
NM
[64Mbit:K4S641632H-UC70]
Hy
na
25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
C83 0.1U
C84 0.1U
C45 0.1U
C46 0.1U
C47 0.1U
C48 0.1U
C49 0.1U
RAMCS1-
DSPVCC33I
RAMDAT7 RAMDAT6
RAMDAT5 RAMDAT4
RAMDAT3 RAMDAT2
RAMDAT1 RAMDAT0
RAMDAT0
RAMDAT1 RAMDAT2
RAMDAT3 RAMDAT4
RAMDAT5 RAMDAT6
RAMDAT7
RAMDQM RAMWERAMCASRAMRAS-
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
7-7
A
EMC
Close to CN201
DVDLD DSPVCC33 CDLD
7-7
B C D E
C50 NM [470pF]
R34 4.7R
+ CE5 220uF/16V
R36 DSPVCC33
220R
LD_DVD
2
R37 1R 0603-R MD_DVD MD_CD R41 SP_MOT2K BAT54C SPDL_SENS+
DSPVCC33
3 1
1
SPDL_SENS+
25 26
C52 1nF
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Q5 9012
220R
LD_CD
0R [300R]
+ CE7 100uF/16V
OPU5V VC1
L11 R44
10uH 33R
RFA5V
U4
PDIC Control: DVD=LOW CD=HIGH CD_DVD FOCUS_S TR_B1 REGO2 SLED_S REGO1 OPEN CLOSE
AM5888S(HSOP-28)
VINFC TR_B1 REGO2 VINSL REGO1 FWD REV GND VCC1 VOTRVOTR+ VOSL+ VOSLVOFCVOFC+ MUTE BIAS VINTK TR_B2 NC VINLD GND GND VCTL NC VCC2 VOLDVOLD+ VOTKVOTK+ 28 27 26 25 24 23 22 30 21 20 19 18 17 16 15
SP_MSP_MOT+ TACTTACT+ SPDL_S C59 1nF C60 1nF C61 27nF C62 27nF VC2 TRACK_S TR_B2 C55 100pF
27 28
TOP
1 2 3 4 5 6 7 29
DRVSB R46
FOCUS_S TRACK_S SPDL_S SLED_S
Close to Vaddis!
R47 R48 R49 R50 51K [27K] 51K [27K] 22K [22K] 51K [33K] FOCUS_PWM TRACK_PWM SPDL_PWM SLED_PWM
1K
C56 0.1uF
C57 0.1uF
+ CE8 47uF/16V
M5V
CE9 100uF/16V C58 0.1uF
M5V
LOADLOAD+
9 10
XP8 6PIN/2.0mm
6 5 4 3 2 1
13 14
M5V
DSPVCC33 XP9 5PIN/2.0mm R51 LOADLOAD+ R52 4.7K HOMESW IN_OUT_SW INSW C63 NM [1nF] C64 NM [1nF] C65 NM [1nF] HOMESW IN_OUT_SW INSW 2.2 OHM 2W
1 2 3 4 5
I a 00 A 5 0 A I a 00 A I 0 A
5.6 OHM 1W R53
R58 1K 1%
C67 0.1uF
I a
TR_B1
00 A 50 A
e
DSPVCC18 DSPVCC33
TR_B2
Q6
Q7 R56
C66 + 0.1uF
SS8550D
SS8550D
CE10 220uF/16v
R57
4.7K/1%
CE11 + 220uF/16v
20k/1%
REGO1 REGO2
R59 GND
12k/1%
R60
10k/1% GND
GND
GND
7-8
A B C D
7-8
E
9012
1
4
U5B LM4558 7
OP +6VA R68 R69 3.3K 10K Q10 9012 CE14 220U/16V + MUTE C70 0.1uF OP+
6
+
CE13 +
10uF/16V R65 R66 10K MUTE R67 470 470 LMAIN_OUT Q9 3904
82K 4.7K C71 75pF U5A LM4558 CE16 10uF/16V R74 + R75 10K MUTE R76 470 470 RMAIN_OUT Q11 3904
OP MUTE_CTL MUTE_CTL R77 4.7K R78 22K Q12 2N3904 +6VA OP+
2 1
+
4 8
8
+12VA C73 0.1uF
+6VA
+12VA
2
+6VA R96 VFE_YIN 1k C74 1uF R81 0R MIC XP10 R82 + CE17 33K 100U/16V + CE18 47uF/16V R79 100K +12VA R80 100R +12V VFE_YIN
2
1 2 3
C76 0.1uF +12V pitch=2.0mm*3 RCA_CVBS_OUT RCA_CVBS_OUT P2 RCA/AUDIO OUT LMAIN_OUT RMAIN_OUT RCA_CVBS_OUT COAX_SPDIF C30 47pF COAX_SPDIF 100 0.1uF C80 100pF C81 100pF C79 100pF
C75 3300p
C77 100p
1 2 3 4 5 6
RCA RCA 0
C78
AUDIO
7-9
7-9
7-10
7-10
7-10
7-10
7-11
7-11
7-12
7-12
8-1
PAC3
PAC11 PAC10
PAC9
PAC6. AV Cable
PAC4. Ueser Manual PAC5. Battery PAC12. Service Hotline PAC13. Service Guarantee PAC14. World Wide Guarantee Card
8-2
It's a general mechanical exploded view for DVP3111/55, pls refer to model set for detailed information. ASSY1 includes components: 2.3.4.19.20.21
8-3
8 15 18 5 9 OPU
1 1 1 1 1 1
1 10 12 14 16 7 AVCABLE Assy1
996510029493 996510029494 996510001175 996510029513 996510006463 996510027099 996510001106 996510029512 996510021451 996510029489 996510020885 996510029498 996510029492 996510001168 996510021448 996510004063 996510029488
FRONT DOOR TOP CABINET POWER CORD BACK PANEL PAD BOTTOM PLATE VIDEO CABLE 1500mm FRONT PANEL ASSY HS 3P TJC-3Y/SCN-3Y L=80MM DISPLAY BOX POWER SOCKET transition REMOTE CONTROL 4PIN CABLE 24PIN HS 6PIN HS CABLE PH-5Y/PH-5Y L=130MM CABLE 9PIN 140MM FH-JC20
1 1 1 1 4 1
1 1 1 1 1 1 1 1 1 1 1
996510009668 996510020926 996510009670 996510009669 996510009669 996510009669 996510009669 996510009669 996510009671 996510021453 996510021453 996510009671 996510009671 996510009670 996510009669 996510020916 996510029496 996510029495 996510011055 996510010924 996510009675
BAT54C IC PESD5V0S1BA TRANSISTOR SMT 3CG9012M SMD.TRANSISTOR MMBT3904LT1 NPN SMD.TRANSISTOR MMBT3904LT1 NPN SMD.TRANSISTOR MMBT3904LT1 NPN SMD.TRANSISTOR MMBT3904LT1 NPN SMD.TRANSISTOR MMBT3904LT1 NPN PNP TRANSISTOR SMD. TRANSISTOR MMBT8550CLT1 SMD. TRANSISTOR MMBT8550CLT1 PNP TRANSISTOR PNP TRANSISTOR TRANSISTOR SMT 3CG9012M SMD.TRANSISTOR MMBT3904LT1 NPN 16M SPI FLASH EON ZR36966PQCG-XF2 16M BIT SDRAM ISC42S16100E-7TL IC CD5888CB Dual operational amplifier 27MCL20PF
12NC No.
Q'ty 4 9 4
D1 D10 D2 D3 D4 D7 D8 L1 L2 T1 U1 U2 U3
996510011047 996500027866 996510011047 996510011047 996510011047 996500014043 996510011047 996510009942 996500032509 996510010954 996510010953 996500027867 996500014609
DIODE IN4007 DIODE SR360 3A/60V DIODE IN4007 DIODE IN4007 DIODE IN4007 DIODE FR102 (FAST RECOVERY) DIODE IN4007 COIL WIDTH COIL SL0811-6R8K2R4 TRANSFORMER CONV IC TNY176PN PHOTOCOUPLER PS2561L1-1-V(WF) IC AM431LP
8-2
It's a general mechanical exploded view for DVP3300/93 and DVP3300X/96, Pls refer to the Model set for detailed information. ASSY1 includes components: 2.3.4.20.21.22
8-3
8 15 18 19 5 9 OPU
1 1 1 1 1 1 1
996510029529 996510029528 996510021454 996510029531 996510006463 996510027099 996510018311 996510001106 996510029527 996510021451 996510029533 996500033761 996510020937 996510029524 996510019879 996510029532 996510021008 996510029523 996500042132 996510019880 996510029492 996510001168 996510021448 996510004063 996510029488 996510022394
FRONT DOOR TOP CABINET 3C PLUG POWER CORD BACK PANEL PAD BOTTOM PLATE ACCESSORY BAG VIDEO CABLE 1500mm FRONT PANEL ASSY HS 3P TJC-3Y/SCN-3Y L=80MM DISPLAY BOX COLOR SERVICE GUARANTEE LEFT CARD WARRANTY LEAFLET POLY BAG QSG RIGHT CARD REMOTE CONTROL SERVICE HOT LINE Worldwideguarantcard 4PIN CABLE 24PIN HS 6PIN HS CABLE PH-5Y/PH-5Y L=130MM CABLE 9PIN 140MM FH-JC20 4PIN CABLE WITH SHIELD L=180MM
1 1 1 1 4 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
CON2 DBOX GRANTEE LBUFFER LEAFLET PBAG QSG RBUFFER RC SHOTLINE WCARD XP1 XP7 XP8 XP9 XS301 XS800
SCREWS LIST: No 6 11 13
996510022393 996510009668 996510020926 996510009670 996510009669 996510009669 996510009669 996510009669 996510009669 996510009671 996510021453 996510021453 996510009671 996510009671 996510009670 996510009669 996510020916 996510029496 996510029495 996510011055 996510010924 996510009675
SMD. DIODE MBRX140 BAT54C IC PESD5V0S1BA TRANSISTOR SMT 3CG9012M SMD.TRANSISTOR MMBT3904LT1 NPN SMD.TRANSISTOR MMBT3904LT1 NPN SMD.TRANSISTOR MMBT3904LT1 NPN SMD.TRANSISTOR MMBT3904LT1 NPN SMD.TRANSISTOR MMBT3904LT1 NPN PNP TRANSISTOR SMD. TRANSISTOR MMBT8550CLT1 SMD. TRANSISTOR MMBT8550CLT1 PNP TRANSISTOR PNP TRANSISTOR TRANSISTOR SMT 3CG9012M SMD.TRANSISTOR MMBT3904LT1 NPN 16M SPI FLASH EON ZR36966PQCG-XF2 16M BIT SDRAM ISC42S16100E-7TL IC CD5888CB Dual operational amplifier 27MCL20PF
12NC No.
Q'ty 6 9 4
D1 D2 D3 D4 D8 D10 D7 L1 L2 T1 U1 U2 U3
996510011047 996510011047 996510011047 996510011047 996510011047 996500027866 996500014043 996510009942 996500032509 996510010954 996510010953 996500027867 996500014609
DIODE IN4007 DIODE IN4007 DIODE IN4007 DIODE IN4007 DIODE IN4007 DIODE SR360 3A/60V DIODE FR102 (FAST RECOVERY) COIL WIDTH COIL SL0811-6R8K2R4 TRANSFORMER CONV IC TNY176PN PHOTOCOUPLER PS2561L1-1-V(WF) IC AM431LP
8-3
8 15 18 19 5 9 OPU
1 1 1 1 1 1 1
996510029529 996510029528 996510021478 996510030194 996510006463 996510027099 996510001106 996510029527 996510010962 996510030187 996510029492 996510001168 996510021448 996510004063 996510029488 996510022394
FRONT DOOR TOP CABINET POWER CORD BACK PANEL PAD BOTTOM PLATE VIDEO CABLE 1500mm FRONT PANEL ASSY 5PIN CBL TJC3-5Y/SCN-5P L=90MM REMOTE CONTROL 4PIN CABLE 24PIN HS 6PIN HS CABLE PH-5Y/PH-5Y L=130MM CABLE 9PIN 140MM FH-JC20 4PIN CABLE WITH SHIELD L=180MM
1 1 1 1 4 1
1 1 1 1 1 1 1 1 1 1
996510022393 996510009668 996510020926 996510009670 996510009669 996510009669 996510009669 996510009669 996510009669 996510009671 996510021453 996510021453 996510009671 996510009671 996510009670 996510009669 996510020916 996510029496 996510029495 996510011055 996510010924 996510009675
SMD. DIODE MBRX140 BAT54C IC PESD5V0S1BA TRANSISTOR SMT 3CG9012M SMD.TRANSISTOR MMBT3904LT1 NPN SMD.TRANSISTOR MMBT3904LT1 NPN SMD.TRANSISTOR MMBT3904LT1 NPN SMD.TRANSISTOR MMBT3904LT1 NPN SMD.TRANSISTOR MMBT3904LT1 NPN PNP TRANSISTOR SMD. TRANSISTOR MMBT8550CLT1 SMD. TRANSISTOR MMBT8550CLT1 PNP TRANSISTOR PNP TRANSISTOR TRANSISTOR SMT 3CG9012M SMD.TRANSISTOR MMBT3904LT1 NPN 16M SPI FLASH EON ZR36966PQCG-XF2 16M BIT SDRAM ISC42S16100E-7TL IC CD5888CB Dual operational amplifier 27MCL20PF
SCREWS LIST: No 6 11 13 12NC No. Description S/T SCREW B 2.6 X 8 BF S/T SCREW B3 X 6 BF S/T SCREW B 3 X 7 BF Q'ty 6 9 4
D1 D10 D7 L1 L2 T1 U1 U2 U3
DIODE IN4007 DIODE SR360 3A/60V DIODE FR102 (FAST RECOVERY) COIL WIDTH COIL SL0811-6R8K2R4 TRANSFORMER CONV. IC TNY176PN PC123X9YFZ IC AM431LP
9-1
REVISION LIST
Version 1.0
* Initial release for DVP3111/55 and DVP3300/93
Version 1.1
* Adding DVP3300/96