Sie sind auf Seite 1von 898

FCR PRIMA Console

Service Manual

CR-IR 391CL

Document No. 020-221-02E First Edition : Apr 28, 2009 Second Edition : Jan 8, 2010

Printed in Japan

Export Restrictions Applying to CR-IR 391CL


Japanese export restrictions and foreign exchange regulations apply to this equipment. Therefore, government approval obtained through due procedure is required in order to export or otherwise remove such equipment from Japan. Note that the same restrictions apply not only to the main unit but also to after-sale parts, service manuals and service training (for exporting or transferring technology) when such items are dispatched or shipped to foreign countries and when service training is given for trainees from foreign countries.

The correlation between mR (milliroentgen), a unit of radiation dose, and C/kg (microcoulomb/kilogram), an international unit of radiation dose, is 1mR=0.258C/kg.

FCR is a trademark or a registered trademark of FUJIFILM Corporation. Copyright 2009-2010 FUJIFILM Corporation. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of FUJIFILM Corporation.

CR-IR 391CL Service Manual

020-221-02E 01.08.2010 FM5563

1. Handling of This Manual


1.1 Notes on the Use of the Service Manual
1.
This document is intended to be read by the service personnel of FUJIFILM Corporation or authorized agent who is commissioned by FUJIFILM Corporation to perform servicing tasks.
Under these circumstances, no one is allowed to perform the following actions without the prior written permission from FUJIFILM Corporation

1.2 Warning and Cautionary Information


Precautions during the service work are indicated by the following terms and symbols.

WARNING
Used when death or serious injuries may occur if this instruction is not observed.

Duplicating or reproducing this document in whole or in part Disclosing this document, in whole or in part, to a person other than the authorized service personnel Lending or transferring this document, in whole or in part, to a third party

CAUTION
Used when minor or medium levels of physical injury may be incurred if the instruction is not observed. Also used when the machine may suffer serious trouble (such as unrecoverable or difficult-to-recover trouble).

2.

Due care must be exercised when handling this document because it contains product internal structure descriptions and other confidential information.
* When the contents of this document need be changed, the information about such changes will be conveyed using Engineering Change Notice (ECN). The Engineering Change Notice (ECN) must also be handled using the same care as for this document.

IMPORTANT
Used when the machine may suffer damage, or any failure or malfunction may occur, if the instruction is not observed.

NOTE
Used to indicate the matters that need attention during steps of the procedure.

3.

Due to a product development schedule, the product specifications and available options/variations prevailing at the time of the release of this document may differ from the descriptions given in this document. In such an instance, a Service Engineering Information will be issued as needed to furnish latest information about inapplicable specifications and components. If you have any doubt about the contents of this document or find errors, contact your local FUJIFILM representative.

REFERENCE
Used to indicate terminology or supplemental explanations.

4.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

2 1.3 Servicing Instruments and Tools that Require Inspection/Calibration


The machine should be installed and serviced by use of servicing instruments and tools that have been regularly inspected and calibrated as appropriate. If the machine were serviced using servicing instruments and tools that have not been inspected and calibrated, proper performance of the machine could not be guaranteed. Servicing instruments and tools that require inspection/calibration are as listed below. The inspection/calibration should be planned and performed in accordance with the specifications and instruction manuals of the applicable servicing instruments and tools.

Instruments and tools that require inspection/calibration


Name
Digital multimeter

Inspection

Calibration

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Contents (CR-IR 391CL Service Manual)

Contents (CR-IR 391CL Service Manual)


Safety Precautions
1. Precautionary Labels................................................................. Safety-1 2. Cautions Relating to Electromagnetic Compatibility............. Safety-3
2.1 Electromagnetic Compatibility Instruction................................... Safety-3

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Contents (CR-IR 391CL Service Manual)

Product Specifications
1. Equipment Specifications......................................................... Spec-1
1.1 Product Code.............................................................................. Spec-1 1.2 Optional Components................................................................. Spec-1 1.3 Dimensions/Weight. ................................................................... Spec-2 1.4 Environmental Conditions........................................................... Spec-2 1.5 Electrical Specifications.............................................................. Spec-2 1.6 Image Storage Performance. ...................................................... Spec-2 1.7 Discarding the Equipment. .......................................................... Spec-2

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Contents (CR-IR 391CL Service Manual)

MD: Machine Description


1. System Configuration. ................................................................ MD-1
1.1 System Configuration................................................................... MD-1 1.2 Operating Environment. ............................................................... MD-1 1.3 Connectors................................................................................... MD-3

2. System Connection Example. .................................................... MD-5 3. Software Function Overview. ..................................................... MD-6 4. Descriptions of Software Control............................................... MD-12
4.1 Data Flow between RU and Console. ........................................... MD-12
4.1.1 Data Flow during Routine Processing...................................... MD-12 4.1.2 Flow of Network Setting Data................................................... MD-12

4.2 Error Handling.............................................................................. MD-13 4.3 What Is Sleep Mode?................................................................... MD-13 4.4 RU Bootup Processing................................................................. MD-14 4.5 RU Termination Processing. ........................................................ MD-15

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Contents (CR-IR 391CL Service Manual)

MT: Machine Troubleshooting


1. Error Code Table..........................................................................
1.1 Referring to Error Messages. ........................................................ 1.2 Precautions................................................................................... 1.3 Error Message..............................................................................

MT-1
MT-1 MT-4 MT-4

4.7 Confirmation Required When Beeps Sound at Computer Startup......................................................................... MT-18 4.8 Error Analysis Tool (Dell Diagnostics).......................................... MT-19
4.8.1 4.8.2 4.8.3 4.8.4 4.8.5 Running the Dell Diagnostics Express Test............................. Memory Checks. ....................................................................... CPU Fan Checks...................................................................... CPU Checks............................................................................. Motherboard Checks................................................................ MT-19 MT-22 MT-22 MT-23 MT-23

2. Using the Event Viewer...............................................................


2.1 Overview of the Event Viewer. ...................................................... 2.2 Starting the Event Viewer............................................................. 2.3 Configuration and How to View the Event Viewer........................ 2.4 Details of Events........................................................................... 2.5 Saving the Event Log. ................................................................... 2.6 Deleting the Event Log................................................................. 2.7 Quitting the Event Viewer............................................................. 2.8 Collecting Logs for Analysis Purposes.........................................

MT-5
MT-5 MT-5 MT-6 MT-6 MT-7 MT-8 MT-9 MT-9

4.9 Checking the Hard Disk................................................................ MT-24 4.10 Tasks to be Performed at Motherboard Replacement. ................ MT-25
4.10.1 Installation Work....................................................................... MT-25 4.10.2 Checkup Work.......................................................................... MT-27

Appendix 1 CR-IR 391CL Error Message Table. .................. AppxMT1-1

2.9 Customizing the Event Viewer...................................................... MT-10

3. Information Useful for Error Recovery. ...................................... MT-11


3.1 Collecting Logs for Maintenance Purpose.................................... MT-11 .................................. MT-11 3.2 Error for Not Registering the Client Device.

4. Troubleshooting (for DELL PC).................................................. MT-12


4.1 Analysis Flow for When Your Computer Does Not Start.............. MT-13 4.2 Analysis Flow for When the Monitor Does Not Operate ....................................................................................... MT-13 Normally. 4.3 Analysis Flow for When the Mouse Does Not Operate ....................................................................................... MT-14 Normally. 4.4 Analysis Flow for When the Keyboard Does Not Operate ....................................................................................... MT-14 Normally. 4.5 Checking the System Lights......................................................... MT-14 4.6 Confirming the Diagnostic Lights.................................................. MT-15
020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Contents (CR-IR 391CL Service Manual)

MC: Checks, Replacement and Adjustment of Parts


1. Reinstalling the OS and the Application.............................................. MC-1
1.11 Restoring the CR-IR 391CL Config Data. .................................... MC-70 1.12 Operation Check and Initialization after Installation..................... MC-73 1.13 Restoring the CR-IR 391CL Configuration Data (patient information)...................................................................... MC-74 1.14 Reconstructing the Image Database............................................ MC-77 1.1 Installation Flowchart (DELL PC). ................................................. MC-1 1.2 Preparation................................................................................... MC-2 1.3 Installing and Setting Up the OS. .................................................. MC-3
1.3.1 Installing and Setting Windows Vista. ....................................... MC-3 1.3.2 Installing the Driver Software. ................................................... MC-12 1.3.3 Setting the OS.......................................................................... MC-25

2. Service Parts Replacement (for DELL PCs).............................. MC-81


2.1 Preparation for Parts Replacement.............................................. MC-81 2.2 Hard Disk...................................................................................... MC-82 2.3 DVD Drive..................................................................................... MC-82 2.4 FD Drive. ....................................................................................... MC-84 2.5 CPU.............................................................................................. MC-84 2.6 Memory......................................................................................... MC-85 2.7 Motherboard................................................................................. MC-86 2.8 Power Supply Unit........................................................................ MC-87

1.4 Setting the Network...................................................................... MC-35


1.4.1 1.4.2 1.4.3 1.4.4 Installing .NET Framework....................................................... Setting the IP address.............................................................. Adding the Windows Components........................................... Setting the Service (Only for Server PC).................................. MC-35 MC-37 MC-40 MC-42

1.5 RU Settings. .................................................................................. MC-43


1.5.1 Installing the RU PC-TOOL...................................................... MC-43 1.5.2 Setting Up and Checking Firewall Settings.............................. MC-46 1.5.3 Installing and Registering RU-AP............................................. MC-52

1.6 Installing the SQL Server.............................................................. MC-58 1.7 Installing the CR-IR 391CL Software............................................ MC-61
1.7.1 1.7.2 1.7.3 1.7.4 Installing the CR-IR 391CL....................................................... Installing a Settings File. ........................................................... Installing Menu and Parameter Files........................................ Installing the Standard Kit CD.................................................. MC-61 MC-63 MC-64 MC-65

3. Updating the Software................................................................. MC-88


3.1 Updating the CR-IR 391CL........................................................... MC-88 3.2 Updating the RU Software............................................................ MC-88

1.8 Settings by the Simplified Setup Wizard. ..................................... MC-66 1.9 IIS Network Virus Protection......................................................... MC-67 1.10 Making Checks Using the Service Utility...................................... MC-68
1.10.1 Running the Simplified Setup Wizard....................................... 1.10.2 Checking for Connection with Other Equipment. ...................... 1.10.3 Checking the Date Format. ....................................................... 1.10.4 Installing Adobe Reader and Copying the Reference Guide. ... 1.10.5 Setting the User Account Control (Activate)............................. MC-68 MC-68 MC-68 MC-68 MC-69

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Contents (CR-IR 391CL Service Manual)

Appendix 1 Setup for Security Enhancement......................... Appendix 2 CR-IR 391CL Software Version Upgrade............. Appendix 3 Option Key / AP Key Installation.......................... 1. Option Key Installation. ........................................................ 2. AP Key Installation. .............................................................. Appendix 4 Setting the RU-Config........................................... Appendix 5 Procedures for Changing the CR-IR 391CL, RU, and Printer IP Addresses............................... 1. Incorporating into the Network. ............................................ 2. Changing the Software Settings..........................................
2.1 Changing the CR-IR 391RU IP Address........................... 2.2 Changing the Printer IP Address...................................... 2.3 Making a setting change using the CR-IR 391CLs Service Utility..................................... 2.4 Changing the CR-IR 391RU Setting................................. 2.5 Changing the Service PC IP Address............................... 2.6 Changing the CR-IR 391CL IP Address........................... 2.7 Restart the CR-IR 391CL , RU, and Printer...................... 2.8 Verifying the connection after IP address changes. ..........

Appx1-1 Appx2-1 Appx3-1 Appx3-1 Appx3-2 Appx4-1 Appx5-1 Appx5-1 Appx5-2


Appx5-2 Appx5-2 Appx5-3 Appx5-6 Appx5-6 Appx5-7 Appx5-7 Appx5-8

Appendix 7 Uninstalling APs.................................................... 1. CR-IR 391CL....................................................................... 2. RU-AP. ................................................................................. 3. RU PC-TOOL. ...................................................................... Appendix 8 Setting the BIOS.................................................... 1. Setting the Dell OptiPlex 760/780.......................................... Appendix 9 Procedure for Changing the Computer Name.... 1. Changing the Computer Name............................................ 2. Registering with the Service Utility......................................
2.1 Starting the Service Utility................................................. 2.2 Cautions when an Error is Displayed................................

Appx7-1 Appx7-1 Appx7-2 Appx7-3 Appx8-1 Appx8-1 Appx9-1 Appx9-1 Appx9-3


Appx9-3 Appx9-4

3. Checkup Work.....................................................................

Appx9-4

Appendix 6 Setting up WakeOnLAN........................................ 1. Installing the WakeOnLAN Utility. ........................................ 2. How to Acquire the RUs MAC Address..................................... 3. How to Acquire the Printers MAC Address................................ 4. Registering the Other Equipment........................................ 5. Testing Automatic Startup...................................................
020-221-02E 01.08.2010 FM5563

Appx6-1 Appx6-1 Appx6-3 Appx6-4 Appx6-5 Appx6-7


CR-IR 391CL Service Manual

Contents (CR-IR 391CL Service Manual)

MU: Maintenance Utility


1. Overview of Service Utility Functions............................................ MU-1 2. Starting, Logging-in to, and Exiting the Service Utility............ MU-2 3. Top Window.................................................................................. MU-4 4. Regional and Language Options Settings................................. MU-5 5. Simplified Setup Wizard.............................................................. MU-8
5.1 Starting the Simplified Setup Wizard............................................ MU-8 5.2 Setting the Date and Time............................................................ MU-9 5.3 System Settings............................................................................ MU-10 5.4 Server Equipment Settings........................................................... MU-11 5.5 Setting the Image Reader. ........................................................... MU-17 5.6 Setting the Film Printer (option).................................................... MU-18 5.7 Setting for DICOM Storage Device (option). ................................. MU-22 5.8 Exiting the Simplified Setup Wizard. ............................................ MU-24 6.4 Film Annotation Characters.......................................................... MU-69
6.4.1 Film Annotation Character Setup (Direct Editing of FilmStrFmt)................................................... 6.4.2 FilmStrFmt File Description Format.......................................... 6.4.3 Changing the Film Annotation Characters. ............................... 6.4.4 Format Descriptors................................................................... 6.4.5 Attribute Descriptors................................................................. 6.4.6 Film Annotation Character Verification Procedure................... MU-74 MU-75 MU-77 MU-80 MU-84 MU-88

6.5 Person Name................................................................................ MU-88 6.6 Modality Settings.......................................................................... MU-91

7. Maintenance Tool......................................................................... MU-92


7.1 Database Utility. ............................................................................ MU-92
7.1.1 7.1.2 7.1.3 7.1.4 Initializing the Patient Database............................................... Initializing the Output Queue.................................................... Initializing the Image Database................................................ Initializing the Preset DB.......................................................... MU-93 MU-94 MU-96 MU-98

7.2 Acquiring EDR Backup Data........................................................ MU-99 7.3 Connection Check........................................................................MU-101 7.4 Log Display/Edit. ..........................................................................MU-102 7.5 Event Log Display.........................................................................MU-103

6. Service Settings........................................................................... MU-25


6.1 System.......................................................................................... MU-25 6.2 Connected Equipment.................................................................. MU-50
6.2.1 6.2.2 6.2.3 6.2.4 6.2.5 6.2.6 6.2.7 Server Equipment Settings....................................................... Monitor Settings. ....................................................................... DICOM Settings. ....................................................................... Disk Drive Settings................................................................... Image Reader Settings. ........................................................... Film Printer Settings (option).................................................... Storage Setup for DICOM Storage Device (option). ................. MU-50 MU-52 MU-53 MU-56 MU-58 MU-60 MU-65

6.3 Linkage Function.......................................................................... MU-68

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Contents (CR-IR 391CL Service Manual)

10

Appendix 1 Backup Utility. ........................................................ Appendix 2 User Utility. ............................................................. Appendix 3 Creating a User...................................................... Appendix 4 Settings for Automatic Output........................................ Appendix 5 Setup for Auto-verify............................................. Appendix 6 DICOM Tag Mapping Function...................................... Appendix 7 Free Drawing Function Settings..........................

Appx1-1 Appx2-1 Appx3-1 Appx4-1 Appx5-1 Appx6-1 Appx7-1

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

10

Contents (CR-IR 391CL Service Manual)

11

SP: Service Parts


1. Service Parts List.........................................................................
1.1 How to Use Service Parts List...................................................... 1.2 Service Parts List..........................................................................

SP-1
SP-1 SP-3

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

11

Contents (CR-IR 391CL Service Manual)

12

PM: Preventive Maintenance


1. Preventive Maintenance Items.................................................... PM-1 2. Checking for a Fatal Error........................................................... PM-2
2.1 Confirming the Event Log............................................................. PM-2

3. Safety............................................................................................ PM-2
3.1 Service Voltage............................................................................ 3.2 Power Plug/Multi-Outlet Power Strip............................................ PM-2 PM-2

4. Hardware Cleaning [reference]................................................... PM-3


4.1 PC Internal Cleaning.................................................................... 4.2 LCD Cleaning............................................................................... PM-3 PM-4

5. Executing the Error Analysis Tool (Dell Diagnostics).............. PM-5


5.1 Conducting the Dell Diagnostics Express Test. ........................... PM-5

6. Functional Checks....................................................................... PM-5


6.1 Confirmation of Image Input to Storage onto DVD....................... 6.2 Image Output to Film.................................................................... PM-5 PM-5

7. Backup of Settings and Verification of Date and Time............. PM-6


7.1 Backup of Setup Files and Log Files............................................ PM-6 7.2 Verification of Date and Time....................................................... PM-12

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

12

Contents (CR-IR 391CL Service Manual)

13

IN: Installation
1. CR-IR 391CL Installation Conditions. .........................................
1.1 Dimensions and Weight................................................................ 1.2 Temperature and Humidity........................................................... 1.3 Places of Installation..................................................................... 1.4 Power Requirements.................................................................... 1.5 Grounding.....................................................................................

IN-1
IN-1 IN-1 IN-1 IN-2 IN-2

4.4.5 4.4.6 4.4.7 4.4.8 4.4.9 4.5.1 4.5.2 4.5.3 4.5.4

Server Equipment Settings....................................................... Setting the Image Reader. ........................................................ Setting the Film Printer............................................................. Setting the Storage Device....................................................... Exiting the Simplified Setup Wizard......................................... Installing the RU PC-TOOL...................................................... Setting Up and Checking Firewall Settings.............................. Installing and Registering RU-AP............................................. Setting the User Account Control (Activate).............................

IN-21 IN-27 IN-27 IN-27 IN-27 IN-28 IN-33 IN-38 IN-42 IN-43 IN-44 IN-44

4.5 RU Settings. .................................................................................. IN-28

2. Installation Procedure Overview................................................ 3. CR-IR 391CL Hardware Setup.....................................................


3.1 Unloading and Unpacking. ............................................................ 3.2 Checking the Component Items................................................... 3.3 Installing the Accessories and Optional Items................................
3.3.1 Keyboard, Mouse, and Power Cable........................................ 3.3.2 Monitor. ..................................................................................... 3.3.3 Film Printer Hardware Setup (option).......................................

IN-3 IN-4
IN-4 IN-5 IN-6
IN-6 IN-6 IN-6

4.6 Film Printer Software Setup (option). ............................................ IN-43


4.6.1 Installing the Option Key for Application Key. ........................... 4.6.2 Reinstalling the AP Key............................................................ 4.6.3 DICOM Print Setup...................................................................

4.7 Checking Connections with Other Equipment...............................

IN-45

4.8 Exiting the Service Utility.............................................................. IN-46

3.4 Connecting a Cable Between the RU and Other Equipment. .......


3.4.1 Making a Cable Connection to the RU..................................... 3.4.2 Film Printer Cable Connection (option)....................................

IN-7
IN-7 IN-7

5. Checkup Work.............................................................................. IN-47


5.1 Checking the Startup and Configuration of the RU...................... IN-47
5.1.1 5.1.2 5.1.3 5.1.4 Checking the Startup of the RU................................................ Checking the RUs Version. ...................................................... Checking the RUs Message File............................................. Checking the RU Configuration................................................ IN-47 IN-50 IN-51 IN-52

4. Software Setup.............................................................................
4.1 Setting the Regional and Language Options................................

IN-8
IN-8

4.2 Changing the Displayed Language and Replacing the Menu Database...................................................................... IN-12 4.3 Option Key / AP Key Installation................................................... IN-15
4.3.1 Option Key Installation. ............................................................. 4.3.2 AP Key Installation................................................................... 4.4.1 4.4.2 4.4.3 4.4.4
020-221-02E 01.08.2010 FM5563

5.2 Checking the System Configuration............................................. IN-53 5.3 Checking Every Step from the Inputting of Images to the Saving of Images onto DVD................................................... IN-53 5.4 Checking Output Images (option)................................................. IN-65

IN-15 IN-16 IN-17 IN-18 IN-19 IN-20

4.4 Setup by the Simplified Setup Wizard.......................................... IN-17


Startup of the Service Utility..................................................... Starting the Simplified Setup Wizard........................................ Setting the Date and Time........................................................ System Settings. .......................................................................

CR-IR 391CL Service Manual

13

Contents (CR-IR 391CL Service Manual)

14

6. Setup File Backup and RU Error Log Verification/Deletion..... IN-68


6.1 Backing Up the CR-IR 391CL Setup File. .......................................... IN-69 6.2 Backing Up the RU Setup File...................................................... IN-76 6.3 Verifying and Deleting the RU Error Log...................................... IN-78
6.3.1 Verifying the RU Error Log....................................................... 6.3.2 Deleting the RU Error Log........................................................ IN-78 IN-79

6.4 Turning OFF the CR-IR 391CL and RU........................................

IN-80

7. Links to Individual Option Items. ................................................ IN-81

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

14

Contents (CR-IR 391CL Service Manual)

15

Appx IN: Installation Appendix


Appendix 1 Settings for Saving Images into DICOM Storage Equipment.............................................................. Appx1-1 1. Hardware Setup. .................................................................. 2. Software Setup....................................................................
2.1 Installing the Option Key................................................... 2.2 Reinstalling the AP Key.................................................... 2.3 Settings in the Service Utility............................................
2.3.1 Settings Regarding This Equipment (DICOM storage SCU settings)................................... 2.2.1 2.2.2 2.2.3 2.2.4 Network Setting........................................................... LinkStation RAID Setting............................................. Shared Folder Setting. ................................................. Confirming Connection between LinkStation and CR-IR 391CL............................................................... Appx2-15 Appx2-18 Appx2-19 Appx2-20

Appx1-1 Appx1-2
Appx1-2 Appx1-3 Appx1-3
Appx1-3

2.3 Setting in the Service Utility.............................................. 3.1 Confirming Connection between LinkStation and CR-IR 391CL (Access to the Network Drive).................... 3.2 Confirming Connection between TeraStation and CR-IR 391CL....................................................................

Appx2-21

3. Connection Check............................................................... Appx2-22


Appx2-22 Appx2-22

2.4 Changing the Display Gradation Correction LUT File.......

Appx1-6

3. Connection Check...............................................................

Appx1-9

4. Backing up the Setup File. ................................................... Appx2-24 5. Turning ON/OFF the NAS. ................................................... Appx2-25
5.1 Always ON........................................................................ 5.2 Manual ON/OFF. ............................................................... 6.1 Creating a Save Destination Folder.................................. 6.2 Synchronization Function Setting..................................... 6.3 Mirroring between NAS. ................................................... Appx2-25 Appx2-25 Appx2-26 Appx2-26 Appx2-30

4. Backing up the Setup File. ................................................... Appx1-12 Appendix 2 Settings for Connection of the NAS.................... 1. Hardware Setup. ..................................................................
1.1 Specifications. ..................................................................
1.1.1 LAN.............................................................................. 1.1.2 RAID............................................................................ 1.1.3 Operation-Certified Models and Software...................

Appx2-1 Appx2-2
Appx2-2
Appx2-2 Appx2-2 Appx2-2

6. Mirroring Setting for Image Folder....................................... Appx2-26

1.2 Installing hardware............................................................


1.2.1 TeraStation.................................................................. 1.2.2 LinkStation...................................................................

Appx2-3
Appx2-3 Appx2-3

7. Restoring Procedures Using the Automatic Backup File..... Appx2-31 Appendix 3 Setting a DICOM MWM Patient information........ 1. Hardware Setup. .................................................................. 2. Software Setup....................................................................
2.1 Installing the Option Key................................................... 2.2 Reinstalling the AP Key.................................................... 2.3 Settings in the Service Utility............................................

Appx3-1 Appx3-1 Appx3-2


Appx3-2 Appx3-3 Appx3-3

2. Software Setup....................................................................
2.1 Installation procedures for TeraStation (TS-WX1.0TL/R1 and TS-WX2.0TL/R1)...........................
2.1.1 2.1.2 2.1.3 2.1.4 Network Setting........................................................... TeraStation RAID Setting............................................ Shared Folder Setting. ................................................. Confirming Connection between TeraStation and CR-IR 391CL...............................................................

Appx2-4
Appx2-4
Appx2-4 Appx2-9 Appx2-13 Appx2-14

3. Connection Check............................................................... 4. Backing up the Setup File. ...................................................


CR-IR 391CL Service Manual

Appx3-5 Appx3-6

2.2 Installation Procedures for LinkStation (LS-WH1.0TGL/R1 and LS-WH2.0TGL/R1).....................


020-221-02E 01.08.2010 FM5563

Appx2-15

15

Contents (CR-IR 391CL Service Manual)

16

PC: Performance Check


CR-IR 391CL Performance Checklist................................................ CR-IR 391CL Config List....................................................................
1. 2. 3. 4. 5. 6. 7. 8. 9. Localize Setting............................................................................ Setting for Institution..................................................................... Setting for Entering Patient Name................................................ Setting is Also Possible with the User Utility. ................................ Setting for Image Collection. ......................................................... Setting for Image Browsing. .......................................................... Setting for General-purpose File Output....................................... Linkage with the Receipt Computer.............................................. Setting for Image Link...................................................................

PC-1 PC-3
PC-3 PC-3 PC-3 PC-3 PC-3 PC-3 PC-4 PC-4 PC-4 PC-4 PC-5 PC-6 PC-6 PC-6 PC-6 PC-7 PC-7 PC-7 PC-7 PC-7

10. Image Incidental Information........................................................ 11. Print Format.................................................................................. 12. Film Character Setting.................................................................. 13. Setting for Output Function........................................................... 14. Operation (Low Frequency) Setting.............................................. 15. Setting for Analysis....................................................................... 16. Settings for Endoscopic Image Import.......................................... 17. Electrocardiographic Data Import Settings................................... 18. PDI Output Function Settings....................................................... 19. Free Layout Setting...................................................................... 20. Setting for DICOM-MWM..............................................................

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

16

Safety-I

CR-IR 391CL Service Manual

Safety Precautions

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Safety-I

Safety Precautions

Safety-II
Reason
New release (FM5535) Revision for software V1.1(B) (FM5563) All pages 3 to 5

Control Sheet
Issue date
04/28/2009 01/08/2010

Revision number
01 02

Pages affected

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Safety-II

1. Precautionary Labels

Safety-1
CAUTIONS
The grounding wire must be connected. To avoid damages to the parts/units due to static discharge, use a wrist strap putting one end on your wrist and the other end on the grounded section of the equipment, as illustrated below. When doing so, make sure to unplug the line cord plug to avoid electrical hazards if using a PC in which the power is energized to the internal power supply or circuits when it is inserted into an outlet.

1. Precautionary Labels
To prevent danger to humans and serious accidents, observe the following.

WARNINGS
Unless indicated otherwise, be sure to turn off the power switch before maintenance work, and disconnect the power plug from the outlet. Even if the power switch is OFF, 100 to 240VAC (differs according to machine specifications) will still be supplied to the primary input terminal of the unit if the power cable is connected, and this may result in possible electric hazards. As neckties, scarves, and necklaces may get caught in the unit during work, remove these items or take precautions against such accidents. Never modify the unit unless otherwise specified. Modification of the safety unit (interlock, breaker, temperature fuse, etc.) will cause serious problems as it is not only dangerous but violates the related laws and regulations.

Wrist strap

00010003.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Safety-1

Safety-2
The unit is also pasted with precautionary labels. Follow the instructions on the labels when carrying out work.

Safety precautions (Control Unit)


Follow the precautions below when installing, using, and servicing the control unit (PC). See the Users Guide provided for details on the control unit. Input voltage : 90V to 135V (60Hz) or 180V to 265V (50Hz) Electric hazard prevention : The power cord of the control unit and monitor uses a 3-pin plug. Connect it to a properly grounded power outlet. When using an extension cord, use a 3-line type with a grounding pin. Place of installation : Avoid places where dust and foreign particles may enter inside through the computer opening. Avoid installing near heaters and heat sources. When installing directly on the floor, ensure that a 5cm or more distance is secured between the equipments bottom face and the floor. Precautions when working on internal parts of the control unit : (1) Turn off the power of the PC, monitor, and other peripheral devices. (2) Disconnect the power cord from the outlet to prevent electric hazard. (3) Open the I/O panel on the rear of the PC, touch the metallic part to fully discharge body static electricity before accessing. (4) When removing the board and memory module, etc., hold them without directly touching the connectors and pins and place them in a static electricity prevention package.

REFERENCE
PC box: Labels shown below are attached on the top face of the PC when it is placed in a vertical position. Identification Label

Sample year of manufacture

Safety Precautions (LCD monitor)


WARNING
High voltage is applied inside the LCD monitor. To prevent electric hazards and danger, the LCD monitors internal parts cannot be accessed. The LCD monitor does not consist of parts serviceable by the service engineer.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Safety-2

Safety-3

2. Cautions Relating to Electromagnetic Compatibility


2.1 Electromagnetic Compatibility Instruction
This equipment complies with the following electromagnetic compatibility (EMC) standard by comforting to the requirements of IEC 60601-1-2:2001+A1:2004/EN 60601-1-2:2001+A1:2006. EMC Standard: CISPR 22:2005/EN 55022:2006 CISPR24:1997+A1:2001+A2:2002/ EN55024:1998+A1:2001+A2:2003 IEC 61000-3-2:2005/EN 61000-3-2:2006 IEC 61000-3-3:1994+A1:2001+A2:2005 However, there is no guarantee that harmful electromagnetic interference will not occur in any installation environment. This equipment generates, uses and can radiate radio frequency energy. In a particular environment, e.g., the equipment is not installed and used in accordance with the instructions or any device that is not compliant with the EMC Standard is used in a surrounding area, harmful interference may result, causing the equipment or surrounding device to malfunction. If this equipment causes harmful interference to other equipment or receives harmful interference from other equipment, you are encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the equipment. Increase the separation between the equipment and the affected equipment. Connect the equipment into an outlet on a circuit different from that to which the affected equipment is connected. If the problem persists, discontinue the use of the equipment and consult the manufacturer of the affected equipment or our official dealer.

Table 1
Guidance and manufacturer's declaration - electromagnetic emissions
The CR-IR 391CL is intended for use in the electromagnetic environment specified below. The customer or the user of the CR-IR 391CL should assure that it is used in such an environment.

Emissions test
Noise terminal voltage CISPR22 Electric field noise strength CISPR22 Harmonic emissions EN61000-3-2 IEC61000-3-2 Voltage fluctuations/ flicker emissions EN61000-3-3 IEC61000-3-3 Complies Class D Class B Class B

Compliance

WARNING
Keep the equipment away from sources of strong electromagnetic radiation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Safety-3

Safety-4
Table 2
Guidance and manufacturer's declaration - electromagnetic immunity
The CR-IR 391CL is intended for use in the electromagnetic environment specified below. The customer or the user of the CR-IR 391CL should assure that it is used in such an environment.

Immunity test
Electrostatic discharge(ESD) EN61000-4-2 IEC61000-4-2 Electrical fast transient/burst EN61000-4-4 IEC61000-4-4 Surge EN61000-4-5 IEC61000-4-5 Voltage dips, short interruptions and voltage variations on power supply input lines EN61000-4-11 IEC61000-4-11 2kV contact 4kV contact 2kV air 4kV air 8kV air

EN/IEC 60601 test level


2kV contact 4kV contact 2kV air 4kV air 8kV air

Compliance level

1kV for power supply lines 0.5kV for input/output lines 0.5, 1kV differential mode 0.5, 1.0, 2.0kV common mode <5% UT (>95% dip in UT) for 0.5 cycle 70% UT (30% dip in UT) for 25 cycles <5% UT (>95% dip in UT) for 250 cycles

1kV for power supply lines 0.5kV for input/output lines 0.5, 1kV differential mode 0.5, 1.0, 2.0kV common mode <5% UT (>95% dip in UT) for 0.5 cycle 70% UT (30% dip in UT) for 25 cycles <5% UT (>95% dip in UT) for 250 cycles 1 A/m

Power frequency (50/60Hz) magnetic field EN61000-4-8 IEC61000-4-8 Conducted RF EN61000-4-6 IEC61000-4-6 Radiated RF EN61000-4-3 IEC61000-4-3

1 A/m

3 Vrms 150 kHz to 80 MHz 3 V/m 80 MHz to 1 GHz

3 Vrms

3 V/m

NOTE: UT is the a.c. mains voltage prior to application of the test level.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Safety-4

Safety-5
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Safety-5

Safety-6
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Safety-6

Spec-I

CR-IR 391CL Service Manual

Product Specifications

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Spec-I

Product Specifications

Spec-II
Reason
New release (FM5535) Revision for software V1.1(B) (FM5563) All pages All pages

Control Sheet
Issue date
04/28/2009 01/08/2010

Revision number
01 02

Pages affected

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Spec-II

Spec-1

1. Equipment Specifications
1.1 Product Code
Hardware
Product Code
IR 391 CL A1-V1 B E

1.2 Optional Components


Product Code
IR 391 LCD-17 E IR 391 LCD-17H E IR 391 LCD-20W E IR 391 MFP E IR 391 DICOM PRINT E 1 1 1 1 1 1 1 IR 391 DICOM STORAGE E IR 391 F-LAYOUT PRINT E IR 391 DICOM ID MWM E

Description
17 inch LCD (DELL E170S) 17 inch LCD (Nanao FlexScan S1721) 20 inch LCD (S2031W-HBK) CR-IR 391CL MFP Key Software CR-IR 391CL DICOM Print Key Software CR-IR 391CL DICOM Standard CR Storage Key Software CR-IR 391CL Free Layout for DICOM Standard Print CR-IR 391CL DICOM ID MWM Key Software

Qty
1 1 1 1 1 1 1 1

Remarks

Description
Control Unit PC control unit (Dell OptiPlex780DT/Core2Duo E7500) Identification label CR-IR 391CL Application Software V1.1(B) CR-IR 391CL Standard Kit Manual Kit for Hospitals CR-IR 391CL Reference Guide CR-IR 391CL Operation Manual (Software License Agreement is included) CR-IR 391CL Quick Guide

Qty

Remarks

Software
Product Code
IR 391 CL SOFT V1 B E

Description
CR-IR 391CL Application Software V1.1(B) Identification label CR-IR 391CL Standard Kit Manual Kit for Hospitals CR-IR 391CL Reference Guide CR-IR 391CL Operation Manual (Software License Agreement is included) CR-IR 391CL Quick Guide

Qty
1 1 1 1 1 1

Remarks

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Spec-1

Spec-2 1.3 Dimensions/Weight


Dimensions (width height depth)
PC Monitor OptiPlex 780DT 399 114 353 (mm) S2031W-HBK DELL E170S S1721-SHBK 427 to 509 469 208.5 (mm) 374.7 380.6 140 (mm) 362 280 to 406 200 (mm)

1.6 Image Storage Performance


Weight
Approx. 8.3 kg Approx. 9.6 kg Approx. 4.63 kg Approx. 5.6 kg

Presented below are the numbers of images that can be stored on the media (measurement values). (Note that actual numbers of images that can be stored may increase/decrease in relation to the values shown in the tables below, depending on the free space available on the disk or image data capacity.)

Hard disk
<Measuring condition> Image storage capacity : 240GB
Image Size 14"17"
Approx. 15,000 images

1.4 Environmental Conditions


Condition
Operating Non-operating

14"14"
Approx 17,000 images

Temperature
10C - 35C -20C - 60C

Humidity
30% - 80%H (No dew condensation) 30% - 80%H (No dew condensation)

Storable number of images

Increase humidity appropriately if it is too dry to operate the equipment during winter.

DVD+RW/DVD-RW
<Measuring conditions> DVD capacity : 4.7GB, UDF format Image size ratio : 14"17" : 14"14" : 10"12" : 8"10" = 1 : 6 : 2 : 1 (for standard image/high-density image)
Standard Image Uncompressed JPEG losslesscompressed High-density Image Uncompressed JPEG losslesscompressed

1.5 Electrical Specifications


Frequency
PC 50Hz/60Hz S2031W-HBK 50Hz/60Hz Monitor DELL E170S S1721-SHBK 50Hz/60Hz 50Hz/60Hz

Input voltage
AC115 to 230V AC100V to 120V AC200V to 240V AC100V to 120V AC200V to 240V AC100V to 120V AC200V to 240V

Max. input current


4.0A/2.0A 0.7A 1.5A 0.65A/0.4A

4.7GB Approx. 650 images Approx. 1,300 images Approx. 200 images Approx. 400 images

1.7 Discarding the Equipment


When discarding the CR-IR 391CL equipment, be sure to dispose of any private information stored on it completely.

Network cable
2. System Connection Example. of MD: Machine Description. 3.4 Connecting a Cable Between the RU and Other Equipment. of IN: Installation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Spec-2

MD-I

CR-IR 391CL Service Manual

MD: Machine Description

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-I

MD: Machine Description

MD-II
Reason
New release (FM5535) Revision for software V1.1(B) (FM5563) Changes in pagination (FM5563)

Control Sheet
Issue date
04/28/2009 01/08/2010

Revision number
01 02

Pages affected
All pages 1, 3, 4, 6 to 8, 16 to 18 5, 9 to 15

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-II

MD-1

1. System Configuration
This section shows the system configuration, which includes the CR-IR 391CL application, and the operating environment for the PC. The following PC is used. Dell OptiPlex 760 (desktop) Dell OptiPlex 780 (desktop)

1.2 Operating Environment


PC Main Unit
Item
CPU HDD Drive System memory 2GB or more 250GB or more DVD-Super Multi Drive (S-ATA) PCI 1 (Necessary for insertion of a video board when the DVI output is used.) Display resolution: 1280 1024 or more Number of display colors: 24bit Color or more * DVI 1.0 or VGA output is recommended. 100BASE-TX 1000BASE-T Windows Vista Business SP1 (32bit) Keyboard connection port: USB or 6-pin mini-DIN PS/2 Mouse connection port: USB or 6-pin mini-DIN PS/2 * The USB 2.0 port is recommended. Keyboard and mouse

Description
Intel Core 2 Duo E7300: 2.66GHz or more; secondary cache: 3072KB or more

1.1 System Configuration


System Configuration
PC main unit Video cable Mother board

Extension slot Graphic Network

Monitor

OS Port Input device

Serial ATA

CR-IR 391CL application CD-ROM System area/image area (drive C)

Monitor
Item
Display resolution

Description
17 inch LCD (S1721-SHBK) 17 inch LCD (DELL E170S) 20 inch LCD (S2031W-HBK) 1280 1024 1280 1024 1680 1050

Option key CD-ROM DVD-Super Multi Drive Network i/f USB Connector Accessories (keyboard and mouse)
020-221-02E 01.08.2010 FM5563

Input format

DVI 1.0 (DVI-I 29-pin) or analog RGB (D-Sub 15-pin)

00000042.ai

CR-IR 391CL Service Manual

MD-1

MD-2
Software
Item
OS Internet Server Internet browser

Description
Windows Vista Business SP1 (32bit) Microsoft Internet Information Service Microsoft Internet Exproler V7.0 or more

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MD-2

MD-3 1.3 Connectors


This section shows locations of the connectors and memory slots of the PCs below. Dell OptiPlex 760 Dell OptiPlex 780

Memory modules
2 GB memory (DIMM1/DIMM2) is installed and shipped from factory. Riser card (ATAPI circuit board) in PCI (SLOT2) is installed and shipped from factory.
System board
DIMM 4 DIMM 2 DIMM 3 DIMM 1 SATA 0 SATA 1

Dell OptiPlex 760


System board location

DIMM sockets (DIMM1/DIMM2 is used)

System board

SATA 3

SATA 2

Diagnostic lights

PCI Express x16 (SLOT1) System lights (power light and hard disk light) PCI(SLOT2) PCI(SLOT3)
MD000274.AI

MD000263.EPS

Connector configuration (PC rear panel)


Parallel port connector NIC connector

Serial port connector Video connector D-Sub (analog output)


020-221-02E 01.08.2010 FM5563

USB port (6-port)


MD000273.AI

CR-IR 391CL Service Manual

MD-3

MD-4
Dell OptiPlex 780
System board location Memory modules
1 GB or 2 GB memory (DIMM1/DIMM2) is installed and shipped from factory. DVI adapter card in PCI Express x16 (SLOT1) is installed and shipped from factory.
System board

Riser card (ATAPI circuit board) in PCI (SLOT2) is installed and shipped from factory.
System board
DIMM 4 DIMM 2 DIMM 3 SATA 0 SATA 1

DIMM sockets (DIMM1/DIMM2 is used)

Diagnostic lights

DIMM 1

SATA 3

System lights (power light and hard disk light)

SATA 2
MD000263.EPS

Connector configuration (PC rear panel)


Parallel port connector Video connector DVI (digital output) Serial port connector NIC connector

PCI Express x16 (SLOT1) PCI(SLOT2) PCI(SLOT3)


MD000276.eps

DisplayProt connector eSATA connector

USB port (6-port) Video connector D-Sub (analog output)

MD000275.eps

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-4

MD-5

2. System Connection Example


This section shows an CR-IR 391CL system connection example.

NOTE
To connect the CR-IR 391CL to the RU, use the following network cable. The UTP type which is compliant with category 5 or more should be used. IEC950/UL1950-compliant cables should be used.

For the network type RU operation


With 100BASE-TX (straight) cables, connect the RU to the CR-IR 391CL via a hub.
100BASE-TX cable (straight) CR-IR 391CL HUB 100BASE-TX cable (straight) RU

Other connected hosts (Film Printer) 100BASE-TX cable (straight)

00000028.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-5

MD-6

3. Software Function Overview


CR Study
Function
Study registration function Displaying a scheduled study

Study Utilities
Function Description
Performs a searching for the study data by way of study of this equipment and study contained on the disks. Searching for study data Filtering is applied to facilitating selection of a target study and then study data is searched for. Displaying the study list Study data selection Study data operation Displays the study list of this equipment and the study list contained on the disks. Selects study data on the study list of this equipment and the study list contained on the disks, and then verifies such study data. Operates the selected study data.

Description
Registers a study to perform image input/verification. Displays a study registered using the study registration function. Modifies information of a registered study. Adding/changing/deleting exposure menus Replacing images Inactivating images/determining mis-exposed images and re-exposures Relocating order of image display Displaying/editing patient information Setting a target destination for image output Inputs images, in conjunction with RU, in an already registered study and verifies images thus collected. Indicates the CR-IR 391CL system status according to the following 6 classifications: RU, Disk, NAS, Printer, Output Queue condition and Event, and then informs the user of the result of indication.

Scheduled study modification function

NAS Drive (Network Attached Storage)


Function
Data management Automatic Image Transfer Process in the background Auto backup of setting/ log

Description
Read/Delete images from NAS. Observe remaining capacity for NAS and study/patient DB. When the capacity of PC HDD is full, the oldest image is transferred to NAS and deleted from the PC HDD. Backup the setting/log automatically to NAS at the time of exiting an application.

Performing a study Indicator function

Patient List
Function
Patient-originated (ID input) Patient-originated (Patient list) Patient-originated (Refer to study data) Patient-originated (Execute CR study) Patient-originated (Import endoscopic and general-purpose image) Monitoring Starting Utilities Customize
020-221-02E 01.08.2010 FM5563

Description
Execute new registration for patient. Search for patient. Refer to and operate the study for selected patient. Execute a CR study for selected patient. Import a general-purpose image and endoscopic image for selected patient. (Endoscope Image Import Function Option/General-Purpose Image Import Function Option are required) Automatic display of retrieved images from the modality. Displays the version information Start up Customize screen Start up Client Utilities/Start up Study Utilities Customize Main window behavior to adjust user workflow

CR-IR 391CL Service Manual

MD-6

MD-7
Image Viewer
Function
Image display/adjustment Windows pattern change Display position relocation Displaying maximized images Feeding display images Displaying additional information Displaying thumbnails Displaying the measured result Tree view display Displaying comparative images Changing gradation Image magnification/image reduction Panning Stack Display Preset Image Processing Reverse display Reset Rotation Flipping FCR image processing parameters Changes display pattern of the study window and the image display window. Relocates image display positions on the study window. Displays fully magnified study images on the viewer window. Alternately changes display images individually by a patient, a study or an image. Displays additional information of the shown image as an image overlay, and also changes between Display and Hide statuses alternately. Displays thumbnails of the shown study images. Also changes between Display and Hide statuses alternately. Displays the measured result, and also changes between Display and Hide statuses alternately. Displays listing of patients/studies in a tree view form, and selects from such list a study you wish to display images. Comparatively displays a currently shown image and the corresponding past image. Changes gradation at real-time basis. Displays magnified/reduced images. Moves display position of an image to a desired position. Switches the display image by mouse dragging. Registers the selected image processing parameters with preset, and changes the preset name or deletes the preset image processing parameters. Performs reverse displays of an image in relation to its density. Resets a display image to a previously stored status. Rotates or flips an image. Adjusts FCR image processing parameters. Applying following Modality LUT according to the modality of each image. N/A P-Value gamma 2.2 FCR Toolbar setting Study status setting Save CR study linkage function Displaying mis-exposed images Modify exposure menu Re-exposure Additional exposures Replacing images Modifying patient information Setting an output device Displays mis-exposed images. Modifies exposure menus. Instructs re-exposure of an image. Adds exposure menus in a study. Replaces study images. Displays/edits patient information. Specifies a target destination for image output. Adding Annotations

Function Description
Restandardization

Description
Modifies standardization conditions so that restandardization processing is performed appropriately. Arrows, shapes, text (character strings), and markers can be added to an image. For the image of an FCR study (not processed) as the object, it is also possible to measure the image and to display the measuring result. Up to 32 annotations can be attached to a single image. Shapes (Ellipses, rectangles, polygons) Markers Measuring result (length, cardiothoracic ratio, angle) Selects, moves and edits already input length and heart-toribcage ratio. Saves measurement results. Measures dimensions of a tumor or the like. Measures the ratio of the widthwise length of the shadow of the heart to that of the ribcage. Measures the angle of two line segments, contact or noncontact, for general-purpose use. Lines can be drawn freely on the viewer window just as with a pen. The following can be done with this free drawing function. Selection of the thickness and the color of the lines to be drawn Capture of the free drawing image (clipboard copy) Deleting of the drawn lines Customizes the toolbar setting. Sets Verify or Verification Suspended individually for each study. Saves image processing parameter information of a study image that has been subjected to image adjustment processing.

Editing selection of measurement results Saving measurement results Length Heart-to-ribcage ratio Angle measurement

Free Drawing

Applying Modality LUT

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-7

MD-8
Function
Image Output Film print Work disk output General-purpose file Using explanatory description Explanatory description use function Indicator function Displays the explanatory description use dialog. Indicates the CR-IR 391CL system status according to the following 5 classifications: RU, Disk, Printer, Output Queue condition and Event, and then informs the user of the result of indication. Outputs a film image to a desired printer. Outputs work media to a desired disk device. Outputs a study image in any of the following formats: BITMAP, JPEG and DICOM Stream

Description

Service Utility
Function
Service settings Simplified setup wizard System Connected equipment Linkage function Film annotation characters Person name Modality setting Maintenance tool Interactively performs various kinds of settings successively. Performs basic system setups. Performs settings for equipment units to be connected to the CR-IR 391CL system. Performs settings for functions that enable linkage with other systems. Performs settings for character strings to be output on film and the formats necessary for output processing. Performs settings necessary for converting an input person name. Performs LUT setting corresponding to each modality. Discards currently used database and restores the stored data, when database files are damaged accidentally or there are inconsistencies between the database and the local images. Acquires/stores EDR backup data files of the selected local images. Checks connection with the equipment determined according to Connected equipment by Service settings. Displays or clears off the number of IP exposures. Starts running the Windows XP event viewer for troubleshooting purposes.

Description

Indicator
Function
Indication RU status display Disk status display

Description
Informs the user of the device connectivity and error information by means of putting the related icon on/off or blinking status. Displays status of a connected RU and performs scanner cleaning. Displays disk status (volume label, application status, usage, write enabled/disabled). *1 Displays listing of disks created as Image storage disks . Performs disk settings. Displays the following NAS status. Remaining capacity Host name Status (Creating write data/Write enable/Temporarily) Displays status of connected printers. Displays Output Queue status and performs Output Queue operations, such as deletion, forced output, and other. Displays listing of events that occurred in the server, such as error, warning, information and other.

Database Utility Acquiring EDR backup data Connection check Log display/edit Event log display

NAS status display Printer status display Output status display Event display

*1 Image storage disk In the CR-IR 391CL system, a disk used for storing study result images as originals is denominated an Image storage disk.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-8

MD-9
User Utility
Function
Menu setting Information of film annotation character strings Setting a destination for image output

Backup Utility
Description
Adds, modifies and deletes exposure menus and study menus. Sets film annotation character strings. Performs settings for whether or not to automatically output images after image generation (after completion of exposure), a target destination for image output, and timings for such operations. Backup Patient Information Patient information database Exposure menu related parameters Image processing parameters System settings (including User Utility related settings) Connection device settings (including automatic output settings) LUT settings Person name format settings Film annotation character related settings User settings Explanatory description settings IP counter information Operation log Changed history log Output history log CR-IR 391CL system event log Patient information database System settings (including User Utility related settings) Connection device settings (including automatic output settings) LUT settings Person name format settings Film annotation character related settings Additional information display settings Search parameter settings User settings Explanatory description settings IP counter information (service authority only)

Function

Description

Setup information

Sets a function to automatically have a study to be determined when Settings for automatically a certain time period elapses after image generation (after determining a study completion of exposure). Setting to delete images Backup notification setting Settings for displaying additional image information Setting to display a title of respect prefixed to a patient name Disk consistency check Importing patient database Settings for startup of clients application History information consistency check Automatic logoff setting Marker setting Preset setting Sets a function to store images input from an external device for a certain time period, and then deleting those images automatically. Sets a function to display a message prompting the user to make backup copies of the necessary data when such copies are not made for a certain time period. Sets image information to be displayed as additional image information. Sets a function to add a title of respect when displaying a patient name. Checks if any alteration was made on the Image storage disk*1. Registers patient information to the patient database from a file where the patient information is described in the CSV format. Sets automatic startup of a client after the server application has started running. Checks if any alteration was made on the history information file (where the history of login, access to a study, data transfer and data backup is registered). Sets whether or not to automatically log off the system when there were no user operations for a certain period of time. Sets the marker to be added to the image. Assigns preset settings to the keypad keys. Log information

Restore Patient Information Menu Setting Information Exposure menu related parameters

System configuration information

User information Explanatory information Log information Collecting logs for maintenance purpose Menu Setting Information

Exposure menu related parameters Image processing parameters System settings Connection device settings LUT settings Person name format settings Film annotation character related settings Additional information display settings Search parameter settings Directory information

*1 Image storage disk In the CR-IR 391CL system, a disk used for storing study result images as originals is denominated an Image storage disk.

Setup information

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-9

MD-10
Function
User information Explanatory information User settings N/A IP counter information Operation log Changed history log Output history log CR-IR 391CL system event log Analysis log Windows event log Registry file Image database DDO file

Description

Disk Copy Tool


Function Description
Specifies a source drive to perform copy processing. Displays process progression status using the progress bar. Window on which copies Enables canceling of copy processing. are made Sets volume label of the copy source as that of the target copy destination, after completion of file copy processing.

Log information

Image Output
Function
DICOM print output

Description
Generates film printout to a printer connected to the CR-IR 391CL server. Generates output to a disk device connected to the CR-IR 391CL server. Manually outputs study images transferred from the viewer, in either of the BITMAP, JPEG or DICOM Stream format. Stores images on a DICOM storage device that supports the DICOM communication protocol (service class: CR Image Storage).

Client Utilities
Function
Edit patient information. Display of IP use frequency User registration User editing Registering explanatory description History display Disk operation Database restoration

Description
Registers, edits and deletes patient information. Displays the IP use count. Adds and deletes images to be displayed on the user-selected window. For the administrator: Registers, edits and deletes users. Operation authority granted to the user group will be determined. Edits the user logged in the system. N/A Displays access history and image transfer history. Performs disk settings, disk registration and disk reconstruction. Re-registers studies saved on the Image storage disk*1 to the study database.

DICOM media storage output General-purpose file output DICOM storage output

On the free layout print screen, free layout of images is possible for Free Layout DICOM print output of multiple images to one piece of film. The image size also output can be adjusted.

Image Processing
Function
Standardization EDR processing GP processing RP processing DRC processing TAS processing MFP processing FNC processing GPR processing

Description
Image standardization processing (conversion to a 10bit format file) Density correction processing (Exposure Data recognizer) Gradation Processing Response Processing Dynamic Range Control Processing Tomographic Artifacts Suppression processing Multi-objective Frequency Processing Flexible Noise Control processing Grid Pattern Removal processing (removes moire of the grid without sacrificing the image quality)

*1 Image storage disk In the CR-IR 391CL system, a disk used for storing study result images as originals is denominated an Image storage disk.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-10

MD-11
Media Storage
Function
Image management Image update Database restoration (Client utilities) Disk reconstruction (Client utilities) Disk storage (Image output) Image search display (Study list) Disk alteration check (Client utilities) Disk settings (Client utilities)

PDI (Portable Data for Imaging) Patient CD


Description
Maintains and manages patient/study/image information that is saved on the disk into the system. Adds in-study images and updates information for the images stored on the Image storage disk*1. Captures information stored on various disks into the image server and includes such images as those targeted for management. If data contained on disks is illegal, subjects DICOMDIR to reconstruction processing based on contents of the files saved on the disks so that those disks can be used properly. Stores images onto several disks. Uses the Web browser to display listing of images saved on the image server or disks or images themselves. Checks if the disks are altered by third parties. The user sets whether data is write-enabled or -disabled onto disks. Image output

Function

Description
Writes exposed images and captured images from the outside onto a CD-R and DVD-R. Use this function in a region where patients are required to store images compulsorily or when making referral to hospitals. Conforms to IHE*1 TF Transaction RAD-47 Distribute Imaging Information on Media.

*1 IHE : Integrating the Healthcare Enterprise

*1 Image storage disk In the CR-IR 391CL system, a disk used for storing study result images as originals is denominated an Image storage disk.

General-purpose Image Capture


Function Description
This function is available for capture of images derived from connection devices such as digital camera, USB memory, FD/CD/ DVD and other, as well as those located in a folder*1 that can be viewed from My Computer on Windows. A maximum of 50 images can be captured for each study. Manages general-purpose images as study images on the CR-IR 391CL. Enables browsing studies that include general-purpose images selected on the study list on the CR-IR 391CL viewer. This function enables image output onto a DVD for storage/DVD for operation and general-purpose image output.

Image capture

Image management Image browse Image output

*1 To view a folder located on the network, the network drive must be assigned ahead of time.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-11

MD-12

4. Descriptions of Software Control


NOTE
In this chapter, the "RU Application", "RU IP Address", and "RU Configuration" are referred to shortly as RU-AP, RU IP ADDR, and CONFIGURATION, respectively.

4.1.2 Flow of Network Setting Data


Settable items and default values
The settings are made from the RU PC-TOOL. The settable items and their default values are as follows.
Setup items
RU IP address RU subnet mask RU default gateway FTP server IP address RU secure IP address RU secure net address

Setting means
RU PC-TOOL RU PC-TOOL RU PC-TOOL RU PC-TOOL RU PC-TOOL RU PC-TOOL

Default values
172.16.1.10 255.255.0.0 172.16.1.0 172.16.1.20 0.0.0.0 0.0.0.0

4.1 Data Flow between RU and Console


The exchange of data between the RU and Console is described below.

4.1.1 Data Flow during Routine Processing


Flow of image data
The image data read from the IP is stored in the SDRAM of the CPU board, and transferred to the Console via the network.

Flow of network setting data


The network setting data is not written into the CPU board only by clicking [SET] button on the RU PC-TOOL window. You need click [UPDATE] button to write the network setting data into the CPU board. The contents set from the RU PC-TOOL are stored on the CPU board FLASH ROM.
Console RU PC-TOOL Network setting data [SET] [UPDATE] Network setting data RU CPU board FLASH ROM

Flow of log data


The log data is written into the FTP server upon RU shutdown processing or upon occurrence of a FATAL error. The log data is retained in the FTP server until a certain amount of that data is reached, and, once that amount is exceeded, the data is overwritten on a first-in, first-out basis.
Console Image data FTP server COMMON CPU board FLASH ROM RU

Memory (SDRAM) Image data Log data RU-specific data


FRRB102002.ai

Log data
FRRB102001.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-12

MD-13 4.2 Error Handling


The RU resumes its operation by attempting a retry(s), except under condition where it is inoperable.

4.3 What Is Sleep Mode?


The "Sleep mode" is such that, in order to save power, the conditions in the machine automatically change to the power-saving mode when the RU is not operated within a specified period of time.

Error Handling
When an I/O error (mechanical, scanner, etc.) occurs between cassette insertion and IP reading, the IP is returned to the cassette.

Operation in the Sleep Mode


Upon entering the Sleep mode, only the power of the CPU board is kept ON, while the power of other components is left OFF. Only the power/erasing mode indicator lamp on the operation panel lights up in green in the Sleep mode.

Cases where Retry Is Impossible (FATAL Error)


(1) When the function of the CPU board stops. (2) When the power supply voltage output stops.

Transition to the Sleep Mode


Transition requirements
If "Sleep mode ON" is set in the CONFIGURATION and the RU is not operated within the preset "Sleep mode transition time" while the RU remains in READY state, the machine transits to the Sleep mode. The stand-by switch is kept pressed for 4 seconds. When the console is shut down.

Setting the Sleep mode


You can specify whether the Sleep mode is to be used and the period of time in which the machine transits to the Sleep mode in the CONFIGURATION. Whether the Sleep mode is to be used Set by the Sleep mode Change command in the CONFIGURATION. Time to transit to the Sleep mode Set by the Sleep Mode Change Time ([min]) command in the CONFIGURATION.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-13

MD-14
Recovery from Sleep Mode
Recover requirements
Press the stand-by switch.

4.4 RU Bootup Processing


The following self-diagnoses are carried out after the power is turned ON. Connection verification between the RU and the Console is also carried out concurrently with the self-diagnoses.

Processing upon recovery


Upon recovery from the Sleep mode, the RU performs a home-positioning operation of the suction arm. In addition, the initial self-diagnosis of the mechanical components takes place, as well as home-positioning of the RU suction arm, under one of the following conditions. The mechanical components are located at other than the home positions. One of sensors detects an IP. A cassette is set in the RU.

Initialization of the Mechanical Components


The initialization of the mechanical components consists of the following five stages.

Before IP search stage


The cassette cover opening mechanism is moved to the reference position, and the suction arm is moved to the home position.

IP search stage
The motor is rotated by an appropriate amount to convey the IP to a position where it can be confirmed by the sensor, on the assumption that the IP is located at a position where it cannot be detected by the sensor within the machine.

After IP search stage


The suction arm is moved to the home position.

Remaining IP ejection stage


When an IP is found within the machine during the IP search stage, its size is measured and the IP is returned to the cassette. If a cassette is not set in the RU, the message prompting to set an empty cassette appears.

After remaining IP ejection


The self-diagnosis of the cassette cover closing mechanism is carried out, and the cassette hold is released.

Initialization of the Scanner Mechanism


The scanner mechanism is initialized.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-14

MD-15 4.5 RU Termination Processing


Termination processing of the mechanism and the log data storage take place.

NOTE
If the power is turned OFF without performing RU shutdown processing, log data will not be saved.

Flow of RU Shutdown Processing


(1) "Shutdown processing" command
Two instructions are available for a case where system shutdown of the Console is carried out and a case where the stand-by switch of the RU is pressed.

(2) Execute "saving of log data", and turn OFF the power.
Saving of log data: Save HISTORY LOG, TRACE LOG, and ERROR LOG to the FTP server.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-15

MD-16
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-16

MD-17
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-17

MD-18
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MD-18

MT-I

CR-IR 391CL Service Manual

MT: Machine Troubleshooting

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-I

MT: Machine Troubleshooting

MT-II
Reason
New release (FM5535) Revision for software V1.1(B) (FM5563) Changes in pagination (FM5563)

Control Sheet
Issue date
04/28/2008 01/08/2010

Revision number
01 02

Pages affected
All pages 11, 15 to 17, 19 to 23, 28 to 30, Appx MT 1-97 to 348 18, 24 to 27

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-II

MT-1

1. Error Code Table


For errors occurring while the CR-IR 391CL is being used, take appropriate countermeasures following the error codes (and error messages) listed herein.
See 2. Using the Event Viewer.

Meaning of the event (error code)


A five-digit code displayed in the Event column implies the following.

A B C C C
A : Error-detected process 1: Module used in common in the system/indicator/user authentication/Client Utility 2: Main process/routine/study list 3: Input process/CR study 4: Image browse/acquisition process 5: Output process/media control 6: Backup Utility/User Utility/Service Utility/disk copy tool 9: RU B : Error level (See the Table Error Levels.)

1.1 Referring to Error Messages


Event (error code) and event source name
When an error occurs, use the event and event source name information to separate the assumed causes. The event and event source name are displayed in the Source and Event columns of the Event Viewer main window shown below.
Source column Event ID column

CCC : For error level 0 or 1, this section of the error code is provided so that it is unique in the process.

00000072.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MT-1

MT-2
Table Error Levels
Error Level
0: Fatal Error An error that fully disables system operation. 1:  Warning An error that enables the systems operation to be continued after user intervention.

Message
Description
A serious, fatal problem that absolutely disables the systems stable operation. DB access error System file access file error Inevitably involves user notification and the system operation can be continued by the user intervention. Causes of this error type can be assumed as follows. Data file access error Disk full Faulty LP board No response from the target destination for connection A slight error that does not require user notification. The system operation can be continued with no user intervention. The following causes can be assumed. Unspecified data entered from networks. (An error implying that the system can be continued being substituted by the default). Information that the system development section wishes to keep. An error presumably caused by defective program. Basically, this error does not occur at users site. This error type has been aborted by the FPD previously. The following causes can be assumed. Unspecified value returned from the method Failure in securing memory Failure in acquiring Windows resources Error returned from the Windows API
00000073.ai

The message is for describing errors and is displayed in the General tab of the Event Viewers Properties window shown below.
General tab

2:  Warning An error that enables the systems continuous operation. 3: Information Simple information 9:  Logical Error Defective program

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MT-2

MT-3
Identifying the problem cause when two or more errors encountered have the same error code
The same error code may appear on the display even when the error cause varies. If you encounter such a situation, note both the error code and error message to identify the error cause.
Event 13005 Event Source Description Causes FFCustom MsgBox MessageBox Dialog A message box could not be Show Error. displayed. The problem is attributable to resource inadequacy or system instability. FFId Connection Recv The connection to the RU was Watch error(%1).%n[%2] closed or an error occurred in the connection. FFId [%1] failed in the The connection to the display group MenuChange liberating table was not successfully closed. processing of the display group data acquisition FFId It failed that [%1] The LangStrDB key was not found PatInfoInput gets the SexMale in Directory.ini or the ID 30705 was caption not registered in the character string data base. FFIdRu Recv error[%1] The connection to the RU was MainControl closed or an error occurred in the connection. FFInput It failed that [%1] The connection character string was connects to STR not properly registered for the DB LangStrDB key in Directory.ini.

To identify the error cause, perform the following procedure:

1. 2.

Start the Event Viewer.


For details of the startup procedure, see 2.2 Starting the Event Viewer.

Open the Event Properties window.


For details the procedure for opening the above window, see 2.4 Details of Events.

3.

13005

See both the error code and error message, and then locate the associated error description in Appendix 1 CR-IR 391CL Error Message Table.
For error messages, see Appendix 1 CR-IR 391CL Error Message Table.

13005

*
13005

Error Message

13005 13005

* There are two or more occurrences of the same error code (event).

Error Code

00000472.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MT-3

MT-4 1.2 Precautions


An error such as incorrectly entered image processing parameters will not be handled as an error. An error code starting with 9 (e.g.: 9XXXX) is that generated by the RU. The correlation between the error level (the second digit of an error code number) of CR-IR 391CL-generated errors and that assumed by Windows (Event Viewer) is as follows. Error level 0 : Fatal Error 1 : Warning 2 : Warning 3 : Information Error level assumed by Windows EVENTLOG_ERROR_TYPE EVENTLOG_WARNING_TYPE EVENTLOG_WARNING_TYPE EVENTLOG_INFORMATION_TYPE

1.3 Error Message


For error messages, see Appendix 1 CR-IR 391CL Error Message Table.

9 : Logical Error EVENTLOG_ERROR_TYPE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MT-4

MT-5

2. Using the Event Viewer


The Windows XP Event Viewer is used for checking details of errors occurring with Windows XP or the CR-IR 391CL. How to use the Event Viewer is described herein, together with the startup procedures.

2.2 Starting the Event Viewer


1.
Start up the Service Utility mode.
For details of Service Utility mode startup, see 2. Starting, Logging-in to, and Exiting the Service Utility in MU: Maintenance Utility.

The Service Utility Top window opens.

2.1 Overview of the Event Viewer


A variety of information items, such as resource information, system operation status and application errors occurring with Windows XP, are recorded (logged) to the Event Viewer. Causes of errors that occur can be specified from the following logs. Application Log Security Log System Log The CR-IR 391CL error information is recorded to the Application Log. To display the CR-IR 391CL error information, select the Application from the tree menu in the left pane of the Event Viewer main window shown below.
MU000001.ai

2.

Click [View Event Log].


The Event Viewer main window opens.

REFERENCE
Use the following procedures if you cannot start up the Event Viewer from the Service Utility mode.
00000371.ai

1. From the [Start] menu at the lower left of the desktop window, select Control Panel to display the Control Panel window. 2. Click Administrative Tools to display the Administrative Tools window. * If the window is in the Classic View option, double-click the same button. 3. Double-click Event Viewer. The Event Viewer starts up.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MT-5

MT-6 2.3 Configuration and How to View the Event Viewer


Explained herein are the Event Viewers screen configuration (shown below) and how to view it.

2.4 Details of Events


Described below are the procedures used for checking detailed event information.

1.

On the Event Viewer main window, click Application log from the tree menu in the left pane to select it.
Event lists appear in the right pane.

2.

Double-click the log you wish to display from the event lists that appear.

E
0000375.ai

A Level:
Symbol Meaning
Error

Description
Displayed when a fatal error, such as failure in device driver or service startup, or loss of data, occurs while the system is running.
00000376.ai

Displayed to indicate that the system has started normally being Information successful in startup of services or remote access. Warning Displayed to indicate that the Warning can be attributable to the cause of the error that has occurred. Should usually be recorded in the log.

The Event Properties window opens.

B C F E

Date and Time Source Event ID Task Category

: The date and time when an event occurs. : The application that wrote an event. : Event ID. : Event category.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MT-6

MT-7
3.
Check detailed information of an event.

2.5 Saving the Event Log


How to save event logs is explained below.

NOTE
Be sure to have a DOS/V-formatted FD ready to use for saving event logs.

1. 2.

Insert the FD used for saving event logs into the FDD. From the Action menu of the Event Viewer main window, select Save Events As....

00000377.ai

4.

Click [OK].
The system returns to the Event Viewer window.
00000378.ai

NOTE
Save Events As... is displayed only when Application log is selected from the tree menu in the left pane of the Event Viewer main window. Make sure to have Application log be selected on the tree menu.
The Save As window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MT-7

MT-8
3.
Select or enter the following.
I.

2.6 Deleting the Event Log


How to delete event logs is explained below.

1.

From the Action menu of the Event Viewer window, select Clear Log.

II.
00000380.ai

NOTE
00000379.ai

I. Select 3 Floppy (A:). II. Enter the filename (e.g.: log).

Clear Log is displayed only when Application log is selected from the tree menu in the left pane of the Event Viewer main window. Make sure to have Application log be selected on the tree menu.
A window opens prompting you to confirm the data to be saved.

REFERENCE
If Text (Tab Separation) is selected for Save as Type, event logs can be saved as text files.

4.

Click [Save].
The following window opens.
00000383.ai

2.

Click [Cancel].
The system returns to the Event Viewer/Application Log window, deleting thus all event logs.

00000070.ai

5. 6.

Click [OK].
The system returns to the Event Viewer/Application Log window.
00000381.ai

Check to see that the FDDs access lamp has gone off and remove the FD from FDD.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MT-8

MT-9 2.7 Quitting the Event Viewer


How to quit the Event Viewer is explained below.

2.8 Collecting Logs for Analysis Purposes


When an error occurs while the CR-IR 391CL system is being used, collect maintenance logs for the purpose of error analysis.

1. 2.

Click

of the Event Viewer main window.

The system returns to the Service Utility top window.

Collecting maintenance logs


For details of how to collect maintenance logs, see Collecting logs for maintenance purpose in Appendix 1: Backup Utility under MU: Maintenance Utility.

Click [EXIT] at the upper right corner of the window.


The system returns to the desktop window.

Items to check at error occurrence


Check the items in the table below and write down the check result accordingly in the notebook.
Check item
1 Precise date of an error occurrence 2 Description of an error occurrence June 15, 2006 No images are saved on the DVD even at the press of the Verify button after image reading. During User Utility operation, the user accidentally changed setup data of Setting for automatically determining a study, which resulted in unselecting Automatically verifying a study. Not reproducible.

Example

3 Operation procedure that caused an error occurrence (What did the user manipulate? What occurred with the equipment as a result of such manipulation?) 4 Is it reproducible? Is it reproduced if a certain procedure is performed? Is it reproduced if a certain condition results? 5 Characteristics

An error caused by a users wrong operation. It is inconceivable that a similar error occurs at different institutions because settings are not changed frequently for the item concerned. User Utility settings already changed appropriately at the site concerned on June 27, 2006. It was also confirmed at the site that images are successfully saved onto the DVD. There are no problems at present.

6 Actions taken by the service personnel What actions did the service personnel take? When did they take such actions? What are the current conditions?

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MT-9

MT-10 2.9 Customizing the Event Viewer


1.
From the View menu of the Event Viewer main window, select Customize....

3.

Select Application from Windows log in the left pane and confirm that the display is as shown below.

00000603.ai

4.
00000601.ai

Select System in the left pane and confirm that the display is as shown below.

The Customize View window opens.

2.

Uncheck the check mark of Action pane and click [OK].

00000604.ai

5.

Click [x] in the upper-right corner of the Event Viewer main window; then the window closes.

00000602.ai

The system returns to the Event Viewer window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MT-10

MT-11

3. Information Useful for Error Recovery


3.1 Collecting Logs for Maintenance Purpose
See Collecting logs for maintenance purpose in Appendix 1: Backup Utility under MU: Maintenance Utility.

3.2 Error for Not Registering the Client Device


If the application is started without executing the service utility after changing the IP address, the following window opens.

MT000093.ai

NOTE
In the case of changing the CR-IR 391CLs own IP address, making an IP address change via the control panel of Windows alone does not affect the setting on the connection destination side. Such a setting will be reflected by opening the Server equipment settings window in the Service Utility and then clicking the [OK] button. The setting contents will be registered to the DB when exiting the Service Utility. For the detailed procedures, see 2.3 Making a setting change using the CR-IR 391CLs Service Utility of Appendix 5: Procedures for Changing the CR-IR 391CL and RU IP Addresses under MC: Checks, Replacement and Adjustment of Parts.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-11

MT-12

4. Troubleshooting (for DELL PC)


The table below summarizes various troubles that may arise with the CR-IR 391CL. In accordance with the encountered trouble, perform a procedure indicated in the Check Method/Remedies column.
Symptom Probable Causes Check Method/Remedies
For the memory check procedure, see 4.8.2 Memory Checks. The CR-IR 391CL (application) does not start up. It is conceivable that the application key might not be installed. Error code: [20102] Setup incompleted. The connection to the network is not established. The MAC address is not acquired. Install the application key. The PC (Windows XP) does not start up. It is conceivable that the PCs memory may be defective. Check the PCs memory. If it is defective, replace it.

Connect the CR-IR 391CL to the network. Reinstall the network driver and then update it. For the reinstallation procedure, see 4.10 Tasks to be Performed at Motherboard Replacement. If the error recurs after the network driver is updated, replace the PCs motherboard.

It is conceivable that the data stored on the hard disk may be partly damaged. IIS may not be running. Error code: [20141]

Check the hard disk. If any error is revealed by the check, perform a procedure for achieving error recovery or replace the hard disk. For the hard disk check procedure, see 4.9 Checking the Hard Disk. Restart the server computer as follows. 1. From the Start menu, open Control Panel Administrative Tools Services. 2. Right-click IIS Admin to select Properties. 3. Ensure that Startup type on the General tab is set to Automatic. If the same symptom recurs, reinstall the CR-IR 391CL system. For how to reinstall the system, see 1. Reinstalling the OS and the Application under MC: Checks, Replacement and Adjustment of Parts.

The SQL server may not be running. Error code: [20140]

Start running the SQL server to restart the server application, as follows. 1. From the Start menu, open Control Panel Administrative Tools Services. 2. Right-click IIS Admin to select Properties. 3. Ensure that Startup type on the General tab is set to Automatic. If the same symptom recurs, reinstall the CR-IR 391CL system. For how to reinstall the system, see 1. Reinstalling the OS and the Application under MC: Checks, Replacement and Adjustment of Parts.

The CR-IR 391CL (application) does not start up.

It is conceivable that the database might not be initialized. The database may have not been initialized though it was necessary to do so at version upgrade or the like.

Initialize the database appropriately. For how to initialize the database, see 7.1.3 Initializing the Image Database under MU: Maintenance Utility.

The communication with the RU or other equipment cannot be established (ping does not work).
020-221-01E 04.28.2009 FM5535

It is conceivable that the network driver may be defective. Update the network driver software version, as necessary. [System event log: type, error; source, EL90Xbc; event ID, 5001]

CR-IR 391CL Service Manual

MT-12

MT-13 4.1 Analysis Flow for When Your Computer Does Not Start
Q1 Y Is the power cable connected properly? N Connect the power cable properly.

4.2 Analysis Flow for When the Monitor Does Not Operate Normally
Q1 Y Is the monitor cable connected properly? N Connect the monitor cable properly.

Q2 Does the power lamp go on when the computer power button is pressed? N Y Replace the computer power unit.
For how to replace the power unit, see 2.8 Power Supply Unit under MC: Checks, Replacement and Adjustment of Parts.

Q2 Is the monitor power turned ON? N Y Turn the monitor power ON.

Q3 Does the power lamp blink yellow when the computer power button is pressed? Y N Replace the computer power unit.
For how to replace the power unit, see 2.8 Power Supply Unit under MC: Checks, Replacement and Adjustment of Parts.

Q3 Is the VGA connector connected correctly? N Y Connect the VGA connector correctly.

Q4 Does the power lamp light yellow when the computer power button is pressed? Y N Check CPU and memory.
4.8.4 CPU Checks 4.8.2 Memory Checks

Q4 Is no error indicated on the diagnostic lights? N Y Take necessary measures following the error indication.
4.6 Confirming the Diagnostic Lights

Q5 Does the power lamp blink green some times and then go off when the computer power button is pressed? Y Verify condition of the diagnostic lights on the back of the computer. N
For how to verify condition of the diagnostic lights, see 4.6 Confirming the Diagnostic Lights.

Replace the monitor.

Q6 Does the power lamp light green when the computer power button is pressed? N Y Verify condition of the diagnostic lights on the back of the computer.
For how to verify condition of the diagnostic lights, see 4.6 Confirming the Diagnostic Lights. 4.8.5 Motherboard Checks

Check the motherboard.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MT-13

MT-14 4.3 Analysis Flow for When the Mouse Does Not Operate Normally
Q1 Y Is the mouse connector connected properly? N Connect the mouse properly.

4.5 Checking the System Lights


The system lights are the power button lights. A problem that occurred in your computer changes status of the lights, as shown in the table below.
Power light Problem Description Suggested Resolution
Power is on, and the computer is operating normally. On the desktop computer, a solid No corrective action is required. green light indicates a network connection. The computer is in a powersaving mode (Microsoft Windows XP). Press the power button, move the mouse, or press a key on the keyboard to wake the computer. Check Diagnostic Lights to see if the specific problem is identified.
For details of the diagnostic lights, see 4.6 Confirming the Diagnostic Lights.

Q2 Turn OFF the computer power and connect/disconnect the connector. Does the same error recur even after the computer is restarted? N END Y Q3 Is the USB port location correct? Confirm the default setup location. N Y Connect the connector to the proper USB port location.
See the manual provided with the computer.

Solid green

Blinking green

Blinks green several times and then turns off

A configuration error exists.

Replace the mouse.

4.4 Analysis Flow for When the Keyboard Does Not Operate Normally
Q1 Y Is the keyboard connector connected properly? N Connect the keyboard properly.

Solid yellow

A device on the system board may be faulty or incorrectly installed.

Check Diagnostic Lights to see if the specific problem is identified.


For details of the diagnostic lights, see 4.6 Confirming the Diagnostic Lights.

Blinking yellow

A power supply or motherboard failure has occurred.

Check Diagnostic Lights to see if the specific problem is identified.


For details of the diagnostic lights, see 4.6 Confirming the Diagnostic Lights.

Q2 Turn OFF the computer power and connect/disconnect the connector. Does the same error recur even after the computer is restarted? N END Y Q3 Is the USB port location correct? Confirm the default setup location. N Y Connect the connector to the proper USB port location.
See the manual provided with the computer.

Solid green and a beep code during POST(*)

A problem was detected while the BIOS was executing.

See Beep Codes for instructions on diagnosing the beep code. Also, check the diagnostic lights to see if the specific problem is identified (see Diagnostic Lights).
For details of the diagnostic lights, see 4.6 Confirming the Diagnostic Lights. For details of diagnosis according to the beep codes, see 4.7 Confirmation Required When Beeps Sound at Computer Startup.

Replace the keyboard.

POST :  An automatically run diagnostic program that BIOS loads for the main components.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MT-14

MT-15
Power light
Solid green power light and no beep code and no video during POST(*) Solid green power light and no beep code, but the computer locks up during POST(*)

Problem Description
The monitor or the graphics card may be faulty or incorrectly installed.

Suggested Resolution
Check Diagnostic Lights to see if the specific problem is identified.
For details of the diagnostic lights, see 4.6 Confirming the Diagnostic Lights.

4.6 Confirming the Diagnostic Lights


To help you troubleshoot a problem, your computer has four lights labeled A, B, C, and D on the front or back panel. The lights can be off or green. When the computer starts normally, the patterns or codes on the lights change as the boot process completes.
CR-IR 391CL

An integrated motherboard device may be faulty.

Check Diagnostic Lights to see if the specific problem is identified.


For details of the diagnostic lights, see 4.6 Confirming the Diagnostic Lights.

POST :  An automatically run diagnostic program that BIOS loads for the main components.

Diagnostic lights
MT000081.eps

Power light
Solid blue Blinking blue

Light pattern (A B C D)

Problem Description
Normal Normal (Standby mode) None.

Suggested Resolution

Turn off

The computer is in a normal off condition, or a Plug the computer into a working electrical outlet possible preand press the power button. BIOS failure has occurred. A possible system board failure has occurred. Remove the power supply plug of the PC. Wait for 1 minute until the power is discharged, plug the computer into a working electrical outlet and press the power button.

Turn off

Solid blue : OFF G : Green

A possible processor failure Reinstall the processor and restart the computer. has occurred.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-15

MT-16
Power light Light pattern (A B C D) Problem Description Suggested Resolution
Turn off the PC, leave the power supply plug inserted, and hold the power supply test button on the back side of the power supply device unit. If a LED next to the switch lights up, a possible system board failure has occurred. If not, remove all the internal and external peripheral devices, and hold the power supply test button on the back side of the power supply device unit. if the LED lights up, a possible peripheral device failure has occurred. If the LED still does not light up, remove the PSU connection from the system board, and hold the power button. If the light lights up, a possible system board failure has occurred. Reinstall the processor, and restart the system. If the PC cannot be restarted, inspect for damage on the processor socket. If you have one memory module installed, reinstall it and restart the computer. If you have two or more memory modules installed, remove the modules, reinstall one module, and then restart the computer. If the computer starts normally, reinstall an additional module. Continue until you have identified a faulty module or reinstalled all modules without error. If available, install properly working memory of the same type into your computer. If the computer has a graphics card, remove the card, reinstall it, and then restart the computer. If the problem still exists, install a graphics card that you know works and restart the computer.

Power light

Light pattern (A B C D)
GG

Problem Description
A possible floppy or hard drive failure has occurred. A possible BIOS failure has occured, or the BIOS is not detected. A possible USB failure has occurred. A possible system board failure has occurred.

Suggested Resolution

Solid blue

Reseat all power and data cables and restart the computer.

Blinking yellow

GG

A possible system board, power supply unit, or peripheral device failure has occurred.

Solid yellow

GGG

Run the BIOS Recovery utility, wait for recovery completion, and then restart the computer.

Solid blue

GGG

Reinstall all USB devices, check cable connections, and then restart the computer. Remove all the internal and external peripheral devices, and start up the PC. After startup, reinstall the peripheral device cards one by one to identify a problematic card. If you have one memory module installed, reinstall it and restart the computer. If you have two or more memory modules installed, remove the modules, reinstall one module, and then restart the computer. If the computer starts normally, reinstall an additional module. Continue until you have identified a faulty module or reinstalled all modules without error. If available, install properly working memory of the same type into your computer. Ensure that no special memory module/memory connector placement requirements exist. Verify that the memory modules that you are installing are compatible with your computer.

Solid yellow

Solid yellow

GGG

No processor is detected.

Solid yellow Solid blue

GG

Memory modules are detected, but a memory failure has occurred.

Solid blue

No memory modules are detected.

Solid blue

GG

A possible graphics card failure has occurred.

Solid blue

GG

Memory modules are detected, but a memory configuration or compatibility error exists.

Solid yellow : OFF G : Green

GG

A possible system board or Replace to another working processor. Inspect processor failure for damage on the processor socket. has occurred.

: OFF G : Green

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-16

MT-17
Power light Light pattern (A B C D) Problem Description Suggested Resolution

Solid blue

GGG

A failure has occurred. This pattern also Ensure that the cables are properly connected to the system board from the hard drive, CD displays when drive, and DVD drive. you enter system setup Check the computer message that appears on your monitor screen. and may not indicate a problem. The power supply connecter is not installed properly. A possible peripheral device card or system board failure has occurred. A possible system board failure has occurred. A possible coin-cell battery failure has occurred. A possible BIOS failure has occurred; the computer is in recovery mode. Reinstall the 2 x 2 power supply connector of the power supply unit firmly.

Solid yellow

GG

Solid yellow

Remove the power supply plug, remove all the peripheral device cards from the PCI and PCI-E slots, and restart the PC. After starts up, turn of the PC again, and reinstall the peripheral device cards one by one to identify a problematic card. Remove all the internal and external peripheral devices, and start up the PC. After startup, reinstall the peripheral device cards one by one to identify a problematic card. Remove the coin-cell battery for 1 minute, reinstall it, and restart the PC.

Solid yellow

GG

Solid yellow

GGG

Run the BIOS Recovery utility, wait for recovery completion, and then restart the computer.

: OFF G : Green

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-17

MT-18 4.7 Confirmation Required When Beeps Sound at Computer Startup


A series of beeps may sound some times consecutively when display of the relevant error message or the problem indication is disabled on the monitor for an error detected at computer startup. Example: One beep + 2 consecutive beeps + 1 beep (beep pattern code: 1-2-1) The beep will sound in different patterns depending on the detected error or problem (Beep code), as shown in the table below.
Beep code
1-1-2 1-1-3 1-1-4 1-2-1 1-2-2 1-2-3 1-3 3-1-1 3-1-2 3-1-3 3-1-4 3-2-2 3-2-4 3-3-1 3-3-2 3-3-4 3-4-1 3-4-2 3-4-3 4-2-1 4-2-2 4-2-3 4-2-4 4-3-1
020-221-02E 01.08.2010 FM5563

Beep code
4-3-3 4-3-4 4-4-1 4-4-2 4-4-3 4-4-4 Timer-chip counter 2 failure Time-of-day clock stopped Serial or parallel port test failure

Cause

Failure to decompress code to shadowed memory Math-coprocessor test failure Cache test failure

Cause
Microprocessor register failure NVRAM read/write failure ROM BIOS checksum failure Programmable interval timer failure DMA initialization failure DMA page register read/write failure Video Memory test failure Slave DMA register failure Master DMA register failure Master interrupt mask register failure Slave interrupt mask register failure Interrupt vector loading failure Keyboard Controller test failure NVRAM power loss Invalid NVRAM configuration Video Memory test failure Screen initialization failure Screen retrace failure Search for video ROM failure No timer tick Shutdown failure Gate A20 failure Unexpected interrupt in protected mode Memory failure above address 0FFFFh

1-3-1 through 2-4-4 Memory not being properly identified or used

CR-IR 391CL Service Manual

MT-18

MT-19 4.8 Error Analysis Tool (Dell Diagnostics)


The Dell OptiPlex ResourceCD, which comes with the computer, is used as the Error Analysis Tool. The Dell OptiPlex ResourceCD includes CD-ROMs that store various kinds of drivers and the CD names differ slightly depending on the computer model used. Items to be checked using the Error Analysis Tool are memory, CPU fan, CPU and motherboard.
For memory checks, see 4.8.2 Memory Checks. For CPU fan checks, see 4.8.3 CPU Fan Checks. For CPU checks, see 4.8.4 CPU Checks. For motherboard checks, see 4.8.5 Motherboard Checks.

4.8.1 Running the Dell Diagnostics Express Test

Starting the Error Analysis Tool (Dell Diagnostics)

1. 2.

Turn ON both the monitor and computer power switches.


The computer starts running.

When F12 Boot Options appears at the upper right corner of the window, press the <F12> key.

NOTE
Unless the <F12> key is pressed with the timeliness, the setup window will not be displayed. In such cases, restart the computer and re-perform Step 2. above.
The Boot Device Menu window opens.
Boot Device Menu

Onboard or USB Floppy Drive SATA0-ST3250310AS Onboard or USB CD-ROM Drive System Setup Diagnostics Use Up/Down arrows to highlight desired item. Use Enter to select highlighted item.
MC000108.a

3.

Insert the DRIVERS AND UTILITIES into the DVD drive.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-19

MT-20
4.
The Press a key to start from the CD/DVD message appears. Press then the <Enter> key.
The Choice Action window opens.
1. Boot from Hard Disk 2. Boot from CD-ROM
MT000077.EPS

Using the Error Analysis Tool (Dell Diagnostics)


Express Test (to be run during regular inspection)

1. 2.

Click Test System on the Choose An Option window.


The Main Menu window opens.

Click Express Test on the Main Menu window.

5.

Press the <1> key.


The Dell Diagnostics Menu window opens.
Dell Diagnostics Menu [1] [2] Dell 32-bit Diagnostics for Resource CD (graphical user interface) for: OptiPlex GX620, GX520, EXIT
MT000082.EPS

Please Enter Selection...


MT000021.EPS

The Express Test will start running. (It will take about 10 minutes to complete. The Success window opens and after clicking [OK], the system returns to the Main Menu window.

6.

Press the <1> key.


Reading of individual modules will start. (It will take about 20 seconds.) After completing module reading, the Choose An Option window opens.

NOTE
If the Error window opens while the test is being run, a message that includes the relevant error code will appear asking if you wish to continue the test. Click [Yes] to continue to run the test.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-20

MT-21
3.
Click Custom Test.
The Customize window opens.

Shutting down the Error Analysis Tool (Dell Diagnostics)

1.

Click the [x] mark at the upper right corner of the window to close the Customize window.
The system returns to the Main Menu window.

2.

Click the [x] mark at the upper right corner of the window to close the Main Menu window.
The computer restarts.

3.

Remove the DVD from the DVD drive.

NOTE
Unless the DVD is removed with the timeliness, the window shown at Step 4. in Starting the Error Analysis Tool (Dell Diagnostics) will open. In such cases, press the <1> key to restart the computer and then remove the DVD.

MT000083.EPS

4.

Click the Results tab on the right-hand side of the window and check to see that all the test items have Passed the Express Test.

NOTE
In the event of an error occurrence, click the Errors tab to check error details and write them down in a notebook. Then, take necessary measures appropriately in accordance with error details.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-21

MT-22
4.8.2 Memory Checks 4.8.3 CPU Fan Checks

1.

Start the Error Analysis Tool (Dell Diagnostics).


For details of the startup procedure, see Starting the Error Analysis Tool (Dell Diagnostics) in 4.8.1 Running the Dell Diagnostics Express Test.

1.

Start the Error Analysis Tool (Dell Diagnostics).


For details of the startup procedure, see Starting the Error Analysis Tool (Dell Diagnostics) in 4.8.1 Running the Dell Diagnostics Express Test.

2.

Click Test Memory on the Choose An Option window .

2. 3.

Click Test System on the Choose An Option window.


The Main Menu window opens.

Select Fan on the Customize window and click Run Tests.

CBS20009.ai

The test process starts running. After all process finished, Record the test results. Press a key when finished. message displayed.

NOTE
It will take about 20 minutes to complete.

MT000083.EPS

The test process will start running. After successfully completing the process, the Success window opens.

3. 4. 5. 6.

Check upper-right area of the window to see all the test items have Passed the Express test. Press <Enter> key to close the Express Test.
The system returns to the Choose An Option window.

4. 5.

Click [OK]. At the completion of the test, click the Errors tab to check to see if there were no errors. In the event of an error occurrence, details of such error will be displayed on the window. Take necessary measures in accordance with on-screen error details. Shut down the Error Analysis Tool (Dell Diagnostics).
For details of the shutdown procedure, see Shutting down the Error Analysis Tool (Dell Diagnostics) in 4.8.1 Running the Dell Diagnostics Express Test.

Click [Exit].
The computer restarts.

Remove the DVD from the DVD drive.

6.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-22

MT-23
4.8.4 CPU Checks 4.8.5 Motherboard Checks

1.

Start the Error Analysis Tool (Dell Diagnostics).


For details of the startup procedure, see Starting the Error Analysis Tool (Dell Diagnostics) in 4.8.1 Running the Dell Diagnostics Express Test.

1.

Start the Error Analysis Tool (Dell Diagnostics).


For details of the startup procedure, see Starting the Error Analysis Tool (Dell Diagnostics) in 4.8.1 Running the Dell Diagnostics Express Test.

2. 3.

Click Test System on the Choose An Option window.


The Main Menu window opens.

2. 3.

Click Test System on the Choose An Option window.


The Main Menu window opens.

Select Processor on the Customize window and click Run Tests.

Select System Board on the Customize window and click Run Tests.

MT000083.EPS

The test process will start running. After successfully completing the process, the Success window opens.

MT000083.EPS

4. 5.

The test process will start running. After successfully completing the process, the Success window opens.

Click [OK]. At the completion of the test, click the Errors tab to check to see if there were no errors. In the event of an error occurrence, details of such error will be displayed on the window. Take necessary measures in accordance with on-screen error details. Shut down the Error Analysis Tool (Dell Diagnostics).
For details of the shutdown procedure, see Shutting down the Error Analysis Tool (Dell Diagnostics) in 4.8.1 Running the Dell Diagnostics Express Test.

4. 5.

Click [OK]. At the completion of the test, click the Errors tab to check to see if there were no errors. In the event of an error occurrence, details of such error will be displayed on the window. Take necessary measures in accordance with on-screen error details. Shut down the Error Analysis Tool (Dell Diagnostics).
For details of the shutdown procedure, see Shutting down the Error Analysis Tool (Dell Diagnostics) in 4.8.1 Running the Dell Diagnostics Express Test.

6.

6.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-23

MT-24 4.9 Checking the Hard Disk


1. 2.
Start up Windows and Select Computer from the menu.

4.

Verify that the check boxes in the Check disk options area are unchecked, and then click [Start].

Select hard disk drive (Local Disk (C:)) and click Properties.

CBS20003.ai

The hard disk check starts. If the hard disk is found to have no problems, a window showing that the hard disk check has been fully completed will open.

5.
CBS20001.ai

Click [Close].

The Local Disk (C:) Properties window opens.

3.

Choose the Tools tab. In the Error-checking area, click [Check Now].
CBS20004.ai

CBS20002.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-24

MT-25 4.10 Tasks to be Performed at Motherboard Replacement


When the motherboard was replaced due, for example, to an error occurring with the PC main unit, all the option functions become inactivated consequently. In such cases, the related option keys must be reinstalled so that the inactivated option functions are activated properly. (Such reinstallation processing includes that to be performed so that the option key which activates the standard function is installed from the standard kit CD.)

4.10.1 Installation Work

Installation of the standard function option keys

1. 2. 3.

Insert the standard kit CD into the DVD drive. Select Computer from the
The Computer window opens.

menu.

Overall operation flow and detailed work procedure


4.10.1 Installation Work Installation of the standard function option keys Option key installation AP key reinstallation

Right-click the drive into which the standard kit CD was inserted and select Open.

4.10.2 Checkup Work Checking the CR-IR 391CL system for its normal startup Checking if the option functions are activated

CBS20005.ai

The content of the standard kit CD opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-25

MT-26
4.
Confirm that installers for the following option keys are available.
Execution file name
OptionGPR OptionHQ OptionFNC GPR image processing HQ image input FNC image processing

6.

Click [Continue].
The installation processing finish window opens.

Function

CBS20008.ai

7. 8. 9.

Click [OK].
The system returns to the standard kit CD window.

Repeat steps 6. through 8. to install all other option keys than Click the button at the upper right corner of the window to close it.

CBS20006.ai

Option key installation


Besides the functions available as the standard, install all the option keys that the institution purchased for its system.
For details of the necessary procedure, see Appendix 3: Option Key / AP Key Installation under MC: Checks, Replacement and Adjustment of Parts.

5.

Double-click

The installation processing start window opens.

AP key reinstallation
Reinstall the AP key accordingly.

NOTE
CBS20007.ai

Reinstall the AP key after all the option keys have been installed appropriately. The reason is that installing the option keys disables the installed AP key, requiring it to be reinstalled anew.
For details of the necessary procedure, see Appendix 3: Option Key / AP Key Installation under MC: Checks, Replacement and Adjustment of Parts.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-26

MT-27
4.10.2 Checkup Work

Checking if the option functions are activated


Use the check list below to make sure that the installed option functions are activated appropriately.
Option name
MFP Key Software

Checking the CR-IR 391CL system for its normal startup


Use the procedure below to check that the CR-IR 391CL starts up normally.

1. 2.

Check details

Remarks

Restart the PC.


The CR-IR 391CL starts up automatically.

Start up the Service Utility mode.


For details of Service Utility mode startup, see 2. Starting, Logging-in to, and Exiting the Service Utility in MU: Maintenance Utility.
DICOM Print Key Software Free Layput Print Key Software DICOM Standard CR Storage Key Software

Start up the User Utility. Make sure that the Available only on the MFP item appears on the Image system where the Processing Parameter Window selected option key is installed. from the Exposure Menu Setup Window. Make sure that the Film print item appears to the right of the Study List window. Make sure that the Freelayout item appears to the right of the Study List window. Make sure that the DICOM Transfer item appears to the right of the Study List window. Available only on the system where the option key is installed. Available only on the system where the option key is installed. Available only on the system where the option key is installed.

The Service Utility Top window opens.

3.

Click [View Event Log].


The Event Viewer main window opens.

REFERENCE
Use the following procedures if you cannot start up the Event Viewer from the Service Utility mode. 1. From the [Start] menu at the lower left of the desktop window, select Control Panel to display the Control Panel window. 2. Click Administrative Tools to display the Administrative Tools window. * If the window is in the Classic View option, double-click the same button. 3. Double-click Event Viewer. The Event Viewer starts up.

4.

Make sure that no errors are recorded in the event log.


For configuration of the Event Viewer and how to view it, see 2.3 Configuration and How to View the Event Viewer.

5.

Click the button at the upper right corner of the window to close the Event Viewer main window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-27

MT-28
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-28

MT-29
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-29

MT-30
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MT-30

Appx MT1-1

Appendix 1 CR-IR 391CL Error Message Table


Event
1

Event Source
VBRuntime

Description
The VBA Application identified by the event source logged this Application IIPMAIN: Thread ID: %1, Logged: IIPMAIN is Normal Terminated. RAID1 Volume XXXXXX changed from a Rebuilding state to Normal state RAID 1 Volume XXXXXX changed from a Normal State to Degraded, Missing Disks State RAID1 Volume XXXXXX is in a Rebuilding state FileTransferCom CoCreateInstance Failed.

Causes
The main process terminated normally.

Remedies

Remarks

3 3 4 2071

IAANTmon IAANTmon

One of the two HDDs constituting RAID1 became defective. One of the two HDDs constituting RAID1 became defective. The defective HDD was replaced. RAID1 was completely rebuilt.

Replace the defective HDD by performing the RAID HDD replacement procedure. Nothing particular.

A RAID volume name used when a XXXXXX=RAID volume was created. A RAID volume name used when a XXXXXX=RAID volume was created. A RAID volume name used when a XXXXXX=RAID volume was created.

IAANTmon OutImgPrc

One of the two HDDs constituting RAID1 Nothing particular. became defective. The defective HDD was replaced. A program error occurred. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

2072

OutImgPrc

COM Initialize Failed.

A program error occurred.

2073

OutImgPrc

DownloadFile Failed.

A program error occurred.

2074

OutImgPrc

DownloadFile some other Exception.

A program error occurred.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-1

Appx MT1-2
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDatabase Access Failure.%n%5

Causes
An attempt to access a database failed. The probable causes are as follows: The search/update process was not successfully performed for the database. An exclusive process was not successfully performed. An attempt to access a file failed.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other) %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10001 FFDBCOM

10015 ImportImageFolder AccessCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Arbitrary Error Details.

A program error occurred.

The program might be faulty. Check the operations performed before and after the error occurrence, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

10101 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nServer process error: Can not Open Indicator-Utility (Server not alive).

The server application is not running.

Start the server application.

10101 FFCustomMsgBox 10102 FFCustomMsgBox

Communication with the server computer resulted in a failure. An unknown error occurred.

Restart the server computer. Restart the server computer.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-2

Appx MT1-3
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not Open Indicator-Utility (User authentication failed).

Causes
The system has not been logged on.

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10105 FCRWeb

10105 FFCustomMsgBox 10106 FCRWeb

You have been logged off the system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nServer process error: Can not get RU-device-info from database (Server not alive).

You were logged off during an operation, or Retry logging onto the system. not logged in. The server application is not running. Start the server application. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10106 FFCustomMsgBox 10107 FCRWeb

Communication with the server computer resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get RU-device-info from database (User authentication failed). The system has not been logged on.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10107 FFCustomMsgBox

You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-3

Appx MT1-4
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nServer process error: Can not send response to RUerror-dialog (Server not alive).

Causes
The server application is not running.

Remedies
Start the server application.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10108 FCRWeb

10108 FFCustomMsgBox 10109 FCRWeb

Communication with the server computer resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not send response to RUerror-dialog (User authentication failed). The system has not been logged on.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10109 FFCustomMsgBox 10110 FCRWeb

You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in. Start the server application. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

ErrorCode:%1%nSubSystem:%2 The server application is not running. %nSourceFile: %3%nSpotCode: %4%nServer process error: Can not register RU-controlcommand to database (Server not alive).

10110

FFCustomMsgBox

Communication with the server computer resulted in a failure.

Restart the server computer.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-4

Appx MT1-5
Event
10111

Event Source
FCRWeb

Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not register RU-controlcommand to database (User authentication failed).

Causes
The system has not been logged on.

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10111 10112

FFCustomMsgBox FCRWeb

You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in. Start the server application. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

ErrorCode:%1%nSubSystem:%2 The server application is not running. %nSourceFile: %3%nSpotCode: %4%nServer process error: Can not get RU-control-result from database (Server not alive).

10112 10113

FFCustomMsgBox FCRWeb

Communication with the server computer resulted in a failure. ErrorCode:%1%nSubSystem:%2 The system has not been logged on. %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get RU-control-result from database (User authentication failed).

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10113

FFCustomMsgBox

You have been logged off the system. You have been logged off the system. You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in. You were logged off during an operation, or Retry logging onto the system. not logged in. You were logged off during an operation, or Retry logging onto the system. not logged in.

10120 FFCustomMsgBox 10122 FFCustomMsgBox

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-5

Appx MT1-6
Event Event Source Description
You are not authorized to perform this operation. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nServer process error: Can not get media-list-info from database (Server not alive). The server application is not running.

Causes

Remedies
Log onto the system with a properly authorized user name to retry this operation. Start the server application.

Remarks

10125 FFCustomMsgBox 10130 FCRWeb

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10130 FFCustomMsgBox 10131 FCRWeb

Communication with the server computer resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get media-list-info from database (User authentication failed). The system has not been logged on.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10131 FFCustomMsgBox 10132 FCRWeb

You have been logged off the system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nServer process error: Can not get media-status from database (Server not alive).

You were logged off during an operation, or Retry logging onto the system. not logged in. The server application is not running. Start the server application. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10132 FFCustomMsgBox

Communication with the server computer resulted in a failure.

Restart the server computer.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-6

Appx MT1-7
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get media-status from database (User authentication failed).

Causes
The system has not been logged on.

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10133 FCRWeb

10133 FFCustomMsgBox 10138 FCRWeb

You have been logged off the system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nServer process error: Can not get printer-info from database (Server not alive).

You were logged off during an operation, or Retry logging onto the system. not logged in. The server application is not running. Restart both the server application and client application. If the same error recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10138 FFCustomMsgBox 10139 FCRWeb

Communication with the server computer resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get printer-info from database (User authentication failed). The system has not been logged on.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10139 FFCustomMsgBox

You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-7

Appx MT1-8
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nServer process error: Can not get output-queue-info from database (Server not alive).

Causes
The server application is not running.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10142 FCRWeb

10142 FFCustomMsgBox 10143 FCRWeb

Communication with the server computer resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get output-queue-info from database (User authentication failed). The system has not been logged on.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10143 FFCustomMsgBox 10144 FCRWeb

You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other) Restart the server computer.

ErrorCode:%1%nSubSystem:%2 The system has not been logged on. %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not operate the output-queue (User authentication failed).

10144 FFCustomMsgBox

Communication with the server computer resulted in a failure.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-8

Appx MT1-9
Event Event Source Description Causes Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10145 FCRWeb

ErrorCode:%1%nSubSystem:%2 The server application is not running. %nSourceFile: %3%nSpotCode: %4%nServer process error: Can not operate the output-queue (Server not alive).

10145 FFCustomMsgBox 10151 FCRWeb

You have been logged off the system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nServer process error: Can not get the specified eventinfo (Server not alive).

You were logged off during an operation, or Retry logging onto the system. not logged in. The server application is not running. Start the server application. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10151 FFCustomMsgBox 10152 FCRWeb

Communication with the server computer resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get the specified eventinfo (User authentication failed). The system has not been logged on.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10152 FFCustomMsgBox

You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-9

Appx MT1-10
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nServer process error: Can not update the status of specified event-info (Server not alive).

Causes
The server application is not running.

Remedies
Start the server application.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10153 FCRWeb

10153 FFCustomMsgBox 10154 FCRWeb

Communication with the server computer resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not update the status of specified event-info (User authentication failed). The system has not been logged on.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10154 FFCustomMsgBox 10159 FCRWeb

You have been logged off the system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nServer process error: Can not call operation-log writer (Server not alive).

You were logged off during an operation, or Retry logging onto the system. not logged in. The server application is not running. Restart both the server application and client application. If the same error recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-10

Appx MT1-11
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not call operation-log writer (User authentication failed).

Causes
The system has not been logged on.

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other) %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10160 FCRWeb

10195 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not Open Indicator-Utility (Other user login).

You have been logged off the system.

10195 FFCustomMsgBox 10196 FCRWeb

You have been logged off the system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not Open Indicator-Utility (Authority is nothing).

You were logged off during an operation, or Retry logging onto the system. not logged in. The current user does not have operating privilege. Log in as a user with operating privileges, and then retry. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10196 FFCustomMsgBox 10197 FCRWeb

You are not authorized to perform this operation. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get RU-device-info from database (Other user login). You have been logged off the system.

Log onto the system with a properly authorized user name to retry this operation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-11

Appx MT1-12
Event Event Source Description
You have been logged off the system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get RU-device-info from database (Authority is nothing).

Causes
The current user does not have operating privilege.

Remedies
Log in as a user with operating privileges, and then retry.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10197 FFCustomMsgBox 10198 FCRWeb

You were logged off during an operation, or Retry logging onto the system. not logged in.

10198 FFCustomMsgBox 10199 FCRWeb

You are not authorized to perform this operation. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not send response to RUerror-dialog (Other user login). You have been logged off the system.

Log onto the system with a properly authorized user name to retry this operation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10199 FFCustomMsgBox 10200 FCRWeb

You have been logged off the system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not send response to RUerror-dialog (Authority is nothing).

You were logged off during an operation, or Retry logging onto the system. not logged in. The current user does not have operating privilege. Log in as a user with operating privileges, and then retry. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

10200 FFCustomMsgBox

You are not authorized to perform this operation.

Log onto the system with a properly authorized user name to retry this operation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-12

Appx MT1-13
Event Event Source Description Causes Remedies Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). 10203 FCRWeb ErrorCode:%1%nSubSystem:%2 You have been logged off the system. %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not register RU-controlcommand to database (Other user login).

10203 FFCustomMsgBox 10204 FCRWeb

You have been logged off the system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not register RU-controlcommand to database (Authority is nothing).

You were logged off during an operation, or Retry logging onto the system. not logged in. The current user does not have operating privilege. Log in as a user with operating privileges, and then retry. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10204 FFCustomMsgBox 10205 FCRWeb

You are not authorized to perform this operation. ErrorCode:%1%nSubSystem:%2 You have been logged off the system. %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get RU-control-result from database (Other user login).

Log onto the system with a properly authorized user name to retry this operation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10205 FFCustomMsgBox 10206 FCRWeb

You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in. Log in as a user with operating privileges, and then retry. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 The current user does not have operating %nSourceFile: %3%nSpotCode: privilege. %4%nAuthentication error: Can not get RU-control-result from database (Authority is nothing).

10206 FFCustomMsgBox

You are not authorized to perform this operation.

Log onto the system with a properly authorized user name to retry this operation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-13

Appx MT1-14
Event Event Source Description
Image Reader operation has been canceled. Image Reader operation ended abnormally. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not open Media-utility windows (Other user login). You have been logged off the system. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

Causes

Remedies

Remarks

10207 FFCustomMsgBox 10208 FFCustomMsgBox 10209 FCRWeb

10209 FFCustomMsgBox 10210 FCRWeb

You have been logged off the system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not open Media-utility windows (Authority is nothing).

You were logged off during an operation, or Retry logging onto the system. not logged in. The current user does not have operating privilege. Log in as a user with operating privileges, and then retry. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10210 FFCustomMsgBox 10211 FCRWeb

You are not authorized to perform this operation. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get media-status from database (Other user login). You have been logged off the system.

Log onto the system with a properly authorized user name to retry this operation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10211

FFCustomMsgBox

You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-14

Appx MT1-15
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get media-status from database (Authority is nothing).

Causes
The current user does not have operating privilege.

Remedies
Log in as a user with operating privileges, and then retry.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10212 FCRWeb

10212 FFCustomMsgBox 10213 FCRWeb

You are not authorized to perform this operation. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get printer-info from database (Other user login). You have been logged off the system.

Log onto the system with a properly authorized user name to retry this operation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10213 FFCustomMsgBox 10214 FCRWeb

You have been logged off the system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get printer-info from database (Authority is nothing).

You were logged off during an operation, or Retry logging onto the system. not logged in. The current user does not have operating privilege. Log in as a user with operating privileges, and then retry. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10214 FFCustomMsgBox 10215 FCRWeb

You are not authorized to perform this operation. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get output-queue-info from database (Other user login). You have been logged off the system.

Log onto the system with a properly authorized user name to retry this operation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10215 FFCustomMsgBox

You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-15

Appx MT1-16
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not get output-queue-info from database (Authority is nothing).

Causes
The current user does not have operating privilege.

Remedies
Log in as a user with operating privileges, and then retry.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10216 FCRWeb

10216 FFCustomMsgBox 10217 FCRWeb

You are not authorized to perform this operation. ErrorCode:%1%nSubSystem:%2 You have been logged off the system. %nSourceFile: %3%nSpotCode: %4%nAuthentication error: Can not operate the output-queue (Other user login).

Log onto the system with a properly authorized user name to retry this operation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10217 FFCustomMsgBox 10218 FCRWeb

You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in. Log in as a user with operating privileges, and then retry. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 The current user does not have operating %nSourceFile:%3%nSpotCode: privilege. %4%nAuthentication error: Can not operate the output-queue (Authority is nothing).

10218 FFCustomMsgBox 10220 FCRWeb

You are not authorized to perform this operation. ErrorCode:%1%nSubSystem:%2 You have been logged off the system. %nSourceFile:%3%nSpotCode:% 4%nAuthentication error: Can not get the specified eventinfo (Other user login).

Log onto the system with a properly authorized user name to retry this operation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10220 FFCustomMsgBox

You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-16

Appx MT1-17
Event Event Source Description Causes Remedies
Log in as a user with operating privileges, and then retry.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10221 FCRWeb

ErrorCode:%1%nSubSystem:%2 The current user does not have operating %nSourceFile:%3%nSpotCode:% privilege. 4%nAuthentication error: Can not get the specified eventinfo (Authority is nothing).

10221 FFCustomMsgBox 10222 FCRWeb

You are not authorized to perform this operation. ErrorCode:%1%nSubSystem:%2 You have been logged off the system. %nSourceFile:%3%nSpotCode:% 4%nAuthentication error: Can not update the status of specified event-info (Other user login).

Log onto the system with a properly authorized user name to retry this operation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10222 FFCustomMsgBox 10223 FCRWeb

You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in. Log in as a user with operating privileges, and then retry. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 The current user does not have operating %nSourceFile:%3%nSpotCode:% privilege. 4%nAuthentication error: Can not update the status of specified event-info (Authority is nothing).

10223 FFCustomMsgBox 10229 FCRWeb

You are not authorized to perform this operation. ErrorCode:%1%nSubSystem:%2 The database was not successfully %nSourceFile:%3%nSpotCode:% connected. The database might not be 4%nIt failed to get RU-device-Info. running. Can not connect to database. Please reboot Server-computer.

Log onto the system with a properly authorized user name to retry this operation. Restart both the server PC and client PC. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-17

Appx MT1-18
Event Event Source Description
Acquisition of Image Reader status information resulted in a failure.

Causes
A database access error occurred.

Remedies
Restart the server computer. Restart both the server PC and client PC.

Remarks

10229 FFCustomMsgBox 10230 FCRWeb

ErrorCode:%1%nSubSystem:%2 The database was not successfully %nSourceFile:%3%nSpotCode:% connected. The database might not be 4%nIt failed to send response to running. RU-error-dialog. Can not connect to database. Please reboot Server-computer.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10230 FFCustomMsgBox 10231 FCRWeb

A failure occurred when trying to respond to the Image Reader.

A database access error occurred.

Restart the server computer. Restart both the server PC and client PC. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 The database was not successfully %nSourceFile:%3%nSpotCode:% connected. The database might not be 4%nIt failed to get RU-controlrunning. result. Can not connect to database. Please reboot Server-computer.

10231 FFCustomMsgBox 10232 FCRWeb

An error occurred while monitoring A database access error occurred. Image Reader operation status.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 An attempt to establish the connection to a Restart both the server PC and client PC. %nSourceFile:%3%nSpotCode:% database failed. The database might not 4%nIt failed to delete RU-control- be running. record. Can not connect to database. Please reboot Server-computer.

10232 FFCustomMsgBox 10233 FCRWeb

An error occurred while monitoring A database access error occurred. Image Reader operation status. ErrorCode:%1%nSubSystem:%2 The database was not successfully %nSourceFile:%3%nSpotCode:% connected. The database might not be 4%nIt failed to release RUrunning. exclusive-info. Can not connect to database. Please reboot Server-computer.

Restart the server computer. Restart both the server PC and client PC. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-18

Appx MT1-19
Event Event Source Description Causes Remedies
Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

Remarks

10233 FFCustomMsgBox 10234 FCRWeb

An error occurred while monitoring A database access error occurred. Image Reader operation status. ErrorCode:%1%nSubSystem:%2 IP address padding failed due to an %nSourceFile:%3%nSpotCode:% exception error. 4%nPadding of IP-address is failed. Please call to service.

10234 FFCustomMsgBox 10235 FCRWeb

An error occurred while monitoring A database access error occurred. Image Reader operation status. ErrorCode:%1%nSubSystem:%2 The database was not successfully %nSourceFile:%3%nSpotCode:% connected. The database might not be 4%nIt failed to get RU-innerrunning. information. Can not connect to database. Please reboot Server-computer.

Restart the server computer. Restart both the server PC and client PC. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10235 FFCustomMsgBox 10236 FCRWeb

A failure occurred in Image Reader operation.

A database access error occurred.

Restart the server computer. Restart both the server PC and client PC. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 The database was not successfully %nSourceFile:%3%nSpotCode:% connected. The database might not be 4%nIt failed to get RU-exclusive- running. info. Can not connect to database. Please reboot Server-computer.

10236 FFCustomMsgBox 10237 FCRWeb

A failure occurred in Image Reader operation.

A database access error occurred.

Restart the server computer. Restart both the server PC and client PC. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 The database was not successfully %nSourceFile:%3%nSpotCode:% connected. The database might not be 4%nIt failed to register RU-control. running. Can not connect to database. Please reboot Server-computer.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-19

Appx MT1-20
Event Event Source Description
A failure occurred in Image Reader operation. ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode:% 4%nIt failed to get Media-deviceinfo. Can not connect to database. Please reboot Server-computer.

Causes
A database access error occurred.

Remedies
Restart the server computer.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10237 FFCustomMsgBox 10238 FCRWeb

An attempt to establish the connection to a Restart both the server PC and client PC. database failed. The problem is attributable to a database timeout or other database error.

10238 FFCustomMsgBox 10239 FCRWeb

An error occurred in an attempt to A database access error occurred. acquire disk information. ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode:% 4%nIt failed to get Media-list. Can not connect to database. Please reboot Server-computer.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

An attempt to establish the connection to a Restart both the server PC and client PC. database failed. The problem is attributable to a database timeout or other database error.

10239 FFCustomMsgBox 10240 FCRWeb

An error occurred in an attempt to A database access error occurred. acquire disk information.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 An attempt to establish the connection to a Restart both the server PC and client PC. %nSourceFile:%3%nSpotCode:% database failed. The database might be 4%nIt failed to get Printer-device- inactive. info. Can not connect to database. Please reboot Server-computer.

10240 FFCustomMsgBox 10241 FCRWeb

A failure occurred in an attempt to A database access error occurred. acquire printer information.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 An attempt to establish the connection to a Restart both the server PC and client PC. %nSourceFile:%3%nSpotCode:% database failed. The database might not 4%nIt failed to get Output-queue- be running. info. Can not connect to database. Please reboot Server-computer.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-20

Appx MT1-21
Event Event Source Description Causes Remedies
Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

Remarks

10241 FFCustomMsgBox 10242 FCRWeb

A failure occurred in an attempt to A database access error occurred. acquire unprinted image information.

ErrorCode:%1%nSubSystem:%2 An attempt to establish the connection to a Restart both the server PC and client PC. %nSourceFile:%3%nSpotCode:% database failed. The Directory.ini file might 4%nIt failed to control Outputbe damaged. queue-info. Can not connect to database. Please reboot Server-computer.

10242 FFCustomMsgBox 10243 FCRWeb

Operation of unoutputted images failed.

A database access error occurred.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 An attempt to establish the connection to a Restart both the server PC and client PC. %nSourceFile:%3%nSpotCode:% database failed. The database might not 4%nIt failed to get Event-info. be running. Can not connect to database. Please reboot Server-computer.

10243 FFCustomMsgBox 10244 FCRWeb

A failure occurred in an attempt to A database access error occurred. acquire event information.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 An attempt to establish the connection to a Restart both the server PC and client PC. %nSourceFile:%3%nSpotCode:% database failed. The database might not 4%nIt failed to update Event-info. be running. Can not connect to database. Please reboot Server-computer.

10244 FFCustomMsgBox 10245 FCRWeb

Operation of unoutputted images failed. ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode:% 4%nIt failed to get Media-devicename. Please call to service.

A database access error occurred.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

An attempt to establish the connection to a Restart both the server PC and client PC. database failed. The problem is attributable to a database timeout or other database error.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-21

Appx MT1-22
Event Event Source Description Causes Remedies
Restart the server computer. With the Service Utility, register the equipment ID. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

Remarks

10245 FFCustomMsgBox 10246 FCRWeb

A failure occurred in an attempt to An error occurred when an attempt was acquire disk information. made to acquire disk information. ErrorCode:%1%nSubSystem:%2 The equipment ID is not registered. %nSourceFile:%3%nSpotCode:% 4%nIt failed to get Media-devicename. Can not find Media-device-name. Please call to service.

10246 FFCustomMsgBox 10247 FFCustomMsgBox

A failure occurred in an attempt to An error occurred when an attempt was acquire disk information. made to acquire disk information. The server device could not be accessed. An unknown error occurred. ErrorCode:%1%nSubSystem:%2 An unknown error occurred during %nSourceFile:%3%nSpotCode:% initialization process. 4%nUnknown Error. In an environment with multiple client computers connected, this can occur when the server load is high and indicator operation is performed. Retry the operation. If the problem is not resolved, check the network connection. Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10300 FFCustomMsgBox 10300 UserAuth

10301 FFCustomMsgBox

User authentication failed.

Restart the server computer and retry. Contact your service engineer if the same symptom recurs even after it has been restarted. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10400 FCRWeb

ErrorCode:%1%nSubSystem:%2 The character string database (API) was %nSourceFile:%3%nSpotCode:% not successfully accessed. 4%nIt failed in character string DB (API) access.

10400 FFCustomMsgBox

An attempt to acquire character strings resulted in a failure.

The problem is attributable to the character string database.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-22

Appx MT1-23
Event Event Source Description Causes Remedies Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). 10401 FCRWeb ErrorCode:%1%nSubSystem:%2 The system setting database (API) was not There is no operational problem (garbled %nSourceFile:%3%nSpotCode:% successfully accessed. characters may be displayed). If you feel 4%nIt failed in system construction uncomfortable, reinstall the CR-IR 391CL. DB (API) access.

10401 FFCustomMsgBox 10402 FCRWeb

Failed in accessing the system setup database.

The problem is attributable to the system setting database. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 The startup information is incorrect. %nSourceFile:%3%nSpotCode:% 4%nStart information is not correct.

10402 FFCustomMsgBox 10403 FCRWeb

System startup failed. ErrorCode:%1%nSubSystem:%2 The current user does not have operating %nSourceFile:%3%nSpotCode:% privilege. 4%nThere is no operation authority.

Retry. Log in as a user with operating privileges, and then retry.

10403 FFCustomMsgBox 10404 FCRWeb

You are not authorized to perform this operation. ErrorCode:%1%nSubSystem:%2 You have been logged off the system. %nSourceFile:%3%nSpotCode:% 4%nIt was logoffed.

Log onto the system with a properly authorized user name to retry this operation. Log in as a user with operating privileges, and then retry. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

10404 FFCustomMsgBox

You have been logged off the system.

You were logged off during an operation, or Retry logging onto the system. not logged in.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-23

Appx MT1-24
Event Event Source Description
Disk replacement failed.

Causes

Remedies
Restart the server computer. Contact your service engineer if the same symptom recurs even after it has been restarted.

Remarks

10625 FFCustomMsgBox

10700 GeneralImageInfo AccessCom

Illegal parameter received.

An illegal parameter was received.

Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Check that the specified image file exists. Also, check that the image file contains a proper endoscope image (JPEG lossy). If the specified image file exists and contains a proper endoscope image (JPEG lossy), restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

10701 GeneralImageInfo AccessCom

Create Instance Error.

The instance generation process was not successfully performed.

10702 GeneralImageInfo AccessCom

Create Instance Error.

The instance generation process was not successfully performed.

10703 GeneralImageInfo AccessCom

File access error.

An attempt to access a file failed.

10704 GeneralImageInfo AccessCom

Release Instance Error.

The instance release process was not successfully performed.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-24

Appx MT1-25
Event Event Source Description
Non-support image file.

Causes
An illegal image file was loaded.

Remedies
Check that the image file contains a proper endoscope image (JPEG lossy). If the image file contains a proper endoscope image (JPEG lossy), restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. (Not used.) Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

10705 GeneralImageInfo AccessCom

10710 FFPresetData AccessCom

ErrorCode: 9999 SourceFile: CPreset.cs Function: 01 SpotCode: x System Error

A program error occurred.

10900 FFInputEz

%1 : Registry Value Get/Set Error Information was not successfully acquired [Key] %2 from the registry. [Exp] %3 %4 %5 %1 : Database Connection Error [DB] %2 [Exp] %3 %4 %5

10901 FFInputEz

(Not used.) An attempt to establish the connection to a Check whether the SQL service manager database failed. is operating normally. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client (Not used.) application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. (Not used.) Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

10902 FFInputEz

%1 : Database Data Get/Set Error A database information acquisition or [DB] %2 storage failed. [Table] %3 [Field] %4 [Exp] %5 %1 : DDO Data Get/Set Error [Tag] %2 %3 %4 %5 The information acquisition/storage operation was not successfully performed in relation to the image information file (DDO).

10903 FFInputEz

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-25

Appx MT1-26
Event Event Source Description
%1 : Other Error [Procedure] %2 [ErrorCode] %3 [Exp] %4 %5

Causes
The information about the system settings was not successfully acquired.

Remedies
Check the information about the settings with the Service Utility. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

10904 FFInputEz

11002

FFDBCOM

ErrorCode:%1%nSubSystem:%2 The method is improperly used. %nSourceFile:%3%nSpotCode:% The probable causes are as follows: 4%nParameter Error. %n%5 An improper value is specified as a parameter. A record existence check error. A record duplication check error. Exclusive check error.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

11010 11010 11020 11030 11040

CustomControl.cs FuriganaEditCtrl.cs FuriganaEditCtrl.cs FuriganaEditCtrl.cs FuriganaEditCtrl.cs

An attempt to exercise the pronunciation automatic input function resulted in a failure. An attempt to enter characters with the software keyboard resulted in a failure. An attempt to move the character cursor position with the software keyboard resulted in a failure.

The OS is abnormal. The application is abnormal. The application is abnormal.

Restart the application. If the same error recurs, reinstall the OS. Restart the application. Restart the application. Restart the application. Restart the application.

An attempt to delete characters in The application is abnormal. the text box with the software keyboard resulted in a failure. The application is abnormal. An attempt to initialize the caret position of a character string in the text box resulted in a failure while the patient information input window was open. An attempt to exercise IME control The application is abnormal. over the patient information input window text box resulted in a failure. An attempt to perform IME setup for the patient information input window text box resulted in a failure. The application is abnormal.

11050

FuriganaEditCtrl.cs

Restart the application.

11060

FuriganaEditCtrl.cs

Restart the application.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-26

Appx MT1-27
Event
11070 11080

Event Source
FuriganaEditCtrl.cs FuriganaEditCtrl.cs

Description
An attempt to change the font style of the patient information input window resulted in a failure. An attempt to perform font setup for the patient information input window text box resulted in a failure.

Causes
The application is abnormal. The application is abnormal.

Remedies
Restart the application. Restart the application.

Remarks

11300

FFCustomMsgBox

An error occurred in an attempt to The problem is attributable to the system acquire system setup information. setting database. Setup processing continues partially by using the existing values. ErrorCode:%1%nSubSystem:%2 An error occurred when an attempt was %nSourceFile:%3%nSpotCode:% made to access a NetConfig.mdb file. The file might be damaged. 4%nNetConfig.mdb File Access Error. Processing continues with the default value. However, check the device information setup with the Service Utility. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

11300

UserAuth

11301 11301

FFCustomMsgBox UserAuth

A failure occurred while accessing the directory setup file. ErrorCode:%1%nSubSystem:%2 A Directory.ini file access error occurred. %nSourceFile:%3%nSpotCode:% The file might be damaged. 4%nDirectory.ini File Access Error.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

11302 11302

FFCustomMsgBox UserAuth

Failed in accessing the character string database.

The problem is attributable to the character string database. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 A character string was not successfully %nSourceFile:%3%nSpotCode:% acquired from the character string 4%nString DB Access Error. database. The database might be damaged.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-27

Appx MT1-28
Event
11303 11303

Event Source
FFCustomMsgBox UserAuth

Description
An attempt to acquire character strings resulted in a failure.

Causes
The problem is attributable to the character string database.

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 An error occurred when an attempt was Restart. If the same symptom recurs, %nSourceFile:%3%nSpotCode:% made to log in automatically. The database perform a reinstallation. 4%nAuto Login Error. might be damaged.

11304 11304

FFCustomMsgBox UserAuth

Processing continued even though an attempt to acquire user information resulted in a failure. ErrorCode:%1%nSubSystem:%2 An error occurred when an attempt was %nSourceFile:%3%nSpotCode:% made to acquire user information. 4%nUser Table Access Error.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

11305 11305

FFCustomMsgBox UserAuth

A failure occurred when initializing exclusive information of a study.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 An error occurred when an attempt was Restart. If the same symptom recurs, %nSourceFile:%3%nSpotCode:% made to perform an exclusive-right deletion perform a reinstallation. 4%nDelete Study Exclusive Error. process for the equipment status table.

11306 11306

FFCustomMsgBox UserAuth

A failure occurred when initializing exclusive information of an equipment unit.

Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 An error occurred when an attempt was Restart. If the same symptom recurs, %nSourceFile:%3%nSpotCode:% made to perform an exclusive-right deletion perform a reinstallation. 4%nDelete RU Exclusive Error. process for the equipment status table.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-28

Appx MT1-29
Event
11307

Event Source
FFCustomMsgBox

Description
Failed in reading the user image.

Causes
In an environment where multiple client computers are connected, this can occur when there is simultaneous login from multiple computers.

Remedies
Log-in operation can be continued. If the problem persists, re-set the user image in the Client Utility.

Remarks

11307

UserAuth

ErrorCode:%1%nSubSystem:%2 An error occurred when an attempt was %nSourceFile:%3%nSpotCode:% made to load a user image. The user 4%nLoad User Icon Error. image might be deleted.

Although there is no operational problem, %1= Error Code: The code that uniquely use the Client Utility to perform user image identifies an error. setup again. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

11308 11308

FFCustomMsgBox UserAuth

An error occurred during user authentication processing. ErrorCode:%1%nSubSystem:%2 An internal system error occurred during %nSourceFile:%3%nSpotCode:% user authentication. 4%nUser Confirm Error.

11309 11309

FFCustomMsgBox UserAuth

Password entered is incorrect.

An incorrect password was entered.

Re-enter Password. Nothing particular.

ErrorCode:%1%nSubSystem:%2 An incorrect password was entered. %nSourceFile:%3%nSpotCode:% 4%nWrong Password was inputted.

11310 11400

FFCustomMsgBox FCRWeb

User selected is not registered or is deleted. ErrorCode:%1%nSubSystem:%2 The search conditions were not specified. %nSourceFile:%3%nSpotCode:% 4%nThe search condition is not specified.

Select another user and log on the system. Specify the search conditions and then retry. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-29

Appx MT1-30
Event
11401

Event Source
FCRWeb

Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode:% 4%nThe use prohibition character is included in patient ID.

Causes

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

An unacceptable character is included in Enter an account name without using the patient ID. You cannot use , #, %, unacceptable characters. &, , +, ?, \, /, , @, 1-byte Katanaka characters, 2-byte characters, or a character string consisting of a blank only.

11402

FCRWeb

ErrorCode:%1%nSubSystem:%2 An unacceptable character is included in Enter an account name without using %nSourceFile:%3%nSpotCode:% the patient name. You cannot use , @, unacceptable characters. 4%nThe use prohibition character or 2-byte characters. is included in the patient name.

11403

FCRWeb

ErrorCode:%1%nSubSystem:%2 The birth date was not properly specified. %nSourceFile:%3%nSpotCode:% 4%nThe specification at date of birth is not correct.

Follow the example and then retry.

11404

FCRWeb

ErrorCode:%1%nSubSystem:%2 The date selected as the end date of the %nSourceFile:%3%nSpotCode:% last update was earlier than the start date. 4%nA past date was selected by the end day of last updated date on the beginning day.

Ensure that the end date of the last update %1= Error Code: The code that uniquely is not earlier than the start date. identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

11405

FCRWeb

ErrorCode:%1%nSubSystem:%2 An attempt was made to execute a function Select a patient from the patient %nSourceFile:%3%nSpotCode:% without selecting a patient from the patient information list, and then retry. 4%nPlease select the patient information list. information list.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-30

Appx MT1-31
Event
11406

Event Source
FCRWeb

Description

Causes

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 No data is input for an essential input item. Set data for an essential input item, and %nSourceFile:%3%nSpotCode:% then retry. 4%nPlease set the input indispensability item.

11407

FCRWeb

ErrorCode:%1%nSubSystem:%2 The entered patient ID already exists. %nSourceFile:%3%nSpotCode:% 4%nPatient ID overlaps.

Enter a different patient ID, and then retry.

11408

FCRWeb

ErrorCode:%1%nSubSystem:%2 An attempt was made to execute a function Perform user information setup and then %nSourceFile:%3%nSpotCode:% without selecting a user from the user retry. 4%nPlease select the user information list. information list.

11409

FCRWeb

ErrorCode:%1%nSubSystem:%2 No data is input for an essential input item. Set data for an essential input item, and %nSourceFile:%3%nSpotCode:% then retry. 4%nPlease set the input indispensability item.

11410

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode:% 4%nThe use prohibition character is included in the account name.

An unacceptable character is included in the account name. You cannot use \, /, |, :, <, >, ?, +, =, , or a character string consisting of a blank only.

Enter an account name without using unacceptable characters.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-31

Appx MT1-32
Event
11411

Event Source
FCRWeb

Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode:% 4%nThe use prohibition character is included in the user-name.

Causes
An unacceptable character is included in the user name. You cannot use \, /, |, :, <, >, ?, +, =, , or a character string consisting of a blank only.

Remedies
Enter an account name without using unacceptable characters.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

11412

FCRWeb

ErrorCode:%1%nSubSystem:%2 Administrator cannot be specified as an %nSourceFile:%3%nSpotCode:% account name. 4%nAdministrator cannot be specified for the account name.

Enter an account name other than Administrator and Service Engineer, and retry.

11413

FCRWeb

ErrorCode:%1%nSubSystem:%2 Service Engineer cannot be specified as %nSourceFile:%3%nSpotCode:% an account name. 4%nService Engineer cannot be specified for the account name.

Enter an account name other than Administrator and Service Engineer, and retry.

11414

FCRWeb

ErrorCode:%1%nSubSystem:%2 The entered password is incorrect. %nSourceFile:%3%nSpotCode:% 4%nThe mistake is found in the password.

Enter a correct password and then retry.

11416

FCRWeb

ErrorCode:%1%nSubSystem:%2 The selected image was deleted. %nSourceFile:%3%nSpotCode:% 4%nThe selected image was deleted. Please select another image.

Select another image.

11416

FFCustomMsgBox

The selected image was deleted.

Select another user image.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-32

Appx MT1-33
Event
11417

Event Source
FCRWeb

Description

Causes

Remedies
Specify another account name.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 The icon picture object was not %nSourceFile:%3%nSpotCode:% successfully created. The error is 4%nThe account name overlaps. attributable to resource insufficiency or system instability.

11418

FCRWeb

ErrorCode:%1%nSubSystem:%2 A password mismatch has been detected. %nSourceFile:%3%nSpotCode:% 4%nThe password is not corresponding.

Enter a correct password.

11419

FCRWeb

ErrorCode:%1%nSubSystem:%2 No image is selected. %nSourceFile:%3%nSpotCode:% 4%nThe image has not been selected.

Select an image, and then retry.

11420

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe image that other users selected is used.

The selected image was used by another user.

Carry it out again after a while.

11421

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nPlease specify the JPEG file.

The specified file was not in JPEG format.

Specify a JPEG file.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-33

Appx MT1-34
Event
11422

Event Source
FCRWeb

Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe size of the picture file is too large.

Causes
The image file size was too large.

Remedies

Remarks

Specify an image file that is not larger than %1= Error Code: The code that uniquely 25 KB. identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). An unacceptable character is included in the category name. Enter a different category name. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

11424

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe use prohibition character is included in the category.

An unacceptable character is included in the category name. You cannot use \, /, |, :, <, >, ?, +, =, , or a character string consisting of a blank only.

11425

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nExplanation information that tried to be registered has already been registered.

An attempt was made to register previously Specify another category name and then registered explanatory information. retry.

11426

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nPlease set the input indispensability item.

No data is input for an essential input item. Set data for the essential input item, and then retry.

11427

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe password is not input.

No password is input.

Enter a password and then retry.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-34

Appx MT1-35
Event
11428

Event Source
FCRWeb

Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nPlease set the input indispensability item.

Causes

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

No data is input for an essential input item. Set data for the essential input item, and then retry.

11429

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe content exceeded 1,000 characters.

The character string in the content field has Edit the character string until it consists of exceeded 1000 characters in length. no more than 1000 characters.

11430

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe account name exceeded 20 characters.

The account name has exceeded 20 characters in length.

Enter an account name consisting of not more than 20 characters.

11431

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe user-name exceeded 20 characters.

The user name has exceeded 20 characters in length.

Enter a user name consisting of not more than 20 characters.

11432

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nMedia the disk management file only for readout are write-protecting it.

The management file was for read only or write-protected.

Retry with a write-enabled medium.

11432

FFCustomMsgBox

The disk is for read only or DVD is write-protected.

Check the contents of the disk.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-35

Appx MT1-36
Event
11433

Event Source
FCRWeb

Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe input volume label name has already been used.

Causes
The entered volume label name is already used.

Remedies
Set a different volume label name, and then retry.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

11433 11434

FFCustomMsgBox FCRWeb

The input volume label name has already been used. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe disk has not been inserted. No disk is inserted into its position.

Specify another volume label name and retry. Insert a disk and then retry. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

11434 11435

FFCustomMsgBox FCRWeb

No disk has been inserted. ErrorCode:%1%nSubSystem:%2 A wrong date format is used. %nSourceFile: %3%nSpotCode: %4%nThe date format is different.

Insert a disk. Set the date in a format that is indicated as %1= Error Code: The code that uniquely an example. identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Delete unnecessary explanatory information and then retry. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

11436

FCRWeb

ErrorCode:%1%nSubSystem:%2 The maximum permissible number of %nSourceFile: %3%nSpotCode: explanatory information registrations was %4%nThe maximum registration exceeded. number of explanation information was exceeded.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-36

Appx MT1-37
Event
11437

Event Source
FCRWeb

Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe exclusive operation is set.

Causes
An exclusive process is set.

Remedies
Carry it out again after a while.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

11437 11438

FFCustomMsgBox FCRWeb

Another user is now operating this system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe manager cannot be deleted. The administrator cannot be deleted.

Carry it out again after a while. Nothing particular. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

11438 11442 11443 11444 11449 11455 11456 11457 11459 11460 11461 11462 11464

FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Administrator can not be deleted. There is no user image. Storing images in read-only disk was requested. Format processing failed. The disk needs to be rebuilt. The disk is in use. The disk has been exchanged. Drive specified does not exist. Selected user information cannot be modified because the user is being logged on. User information logging on cannot be deleted. An automatically verify user can not be deleted. User selected cannot be deleted. Are you sure you want to delete the following user account? %s

Choose a user other than the administrator. Add user images accordingly. Select a rewritable drive and retry. Select a drive which is able to format and retry. Restore the disk. Carry it out again after a while. Check the contents of the disk. Ensure that the drive has been connected correctly and then retry.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-37

Appx MT1-38
Event
11465 11490 11491 11492 11493 11494 11495 11496 11497 11498 11500 11501 11502 11503 11504 11505 11506 11507 11508 11509 11510 11511

Event Source
FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Description
A failure occurred when uploading user images. Setting user ID failed. Patient information corresponding with specified patient ID does not exist. Another process is updating the patient information. Specified Patient ID is already registered. The disk is restored. Current user is not allowed this operation. A fatal error occurred. Specified files do not exist. The server device could not be accessed. A fatal error occurred. The process is being canceled because this system is required to shut down. The process is interrupted by the power supply cut off. Data in the disk is inconsistency. Disk storing failed. Drive specified does not exist. Disk unlocking failed. An error occurred in an attempt to eject disk. Write operations can not be performed for a reference drive. No disk has been inserted. Drive specified is not removable. Disk specified is read-only.

Causes

Remedies
Ensure that the network cable has been connected correctly. This event will not be displayed.

Remarks

Carry it out again after a while.

Are you sure?

Contact your service engineer. Press the button below to close this dialog and terminate the system. In an environment where multiple client computers are connected, this can occur when the server load is high. Retry the operation. If the problem is not resolved, restart the client application. Contact your service engineer. Restart this system and retry. Restart this system and retry. Execute Disk restoration operation. Check the disk status. Ensure that the specified drive has been connected correctly. Check the disk drive status. Check the disk drive status. Use a drive for storage. Insert a disk. Ensure that the specified drive has been connected correctly. Insert a writable disk.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-38

Appx MT1-39
Event
11512 11513 11514 11515 11516 11517 11518 11519 11520 11521 11522 11523 11524 11525 11526 11527 11528 11529 11530 11531 11532 11533 11534 11535 11536

Event Source
FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Description
Disk specified is not inserted. The process is being canceled because this system is required to shut down. The process is interrupted by the power supply cut off. Data in the disk is inconsistency. Drive specified does not exist. Disk locking failed. Write operations can not be performed for a reference drive. Disk specified is in use. No disk has been inserted. Drive specified is not removable. Inserted disk is unformatted. The process is being canceled because this system is required to shut down. The process is interrupted by the power supply cut off. Data in the disk is inconsistency. Free disk space is insufficient. Inserted disk is not new (unused). Disk storing failed. Drive specified does not exist. Inserted disk is write-protected. Disk locking failed. Specified label name is already registered. Inserted disk is not new (unused). Write operations can not be performed for a reference drive. Disk specified is in use. No disk has been inserted.

Causes

Remedies
Confirm the inserted disk. Restart this system and retry. Restart this system and retry. Execute Disk restoration operation. Ensure that the specified drive has been connected correctly. Check the disk drive status. Use a drive for storage. Carry it out again after a while. Insert a disk. Ensure that the specified drive has been connected correctly. Confirm the inserted disk. Restart this system and retry. Restart this system and retry. Execute Disk restoration operation. Confirm the inserted disk. Insert a new disk. Confirm the inserted disk. Ensure that the specified drive has been connected correctly. Confirm the inserted disk. Check the disk drive status. Specify another label name. Insert a new disk. Use a drive for storage. Carry it out again after a while. Insert a disk.

Remarks

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-39

Appx MT1-40
Event
11537 11538 11539 11540 11541 11542 11543 11544 11545 11546 11547 11548 11549 11550 11551 11552 11553 11554 11555 11556

Event Source
FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Description
Drive specified is not removable. The process is being canceled because this system is required to shut down. The process is interrupted by the power supply cut off. Disks cannot be formatted with this drive. Disk formatting failed. Drive specified does not exist. Disk specified is not inserted. The process is being canceled because this system is required to shut down. The process is interrupted by the power supply cut off. Disk specified is not for management. Drive specified does not exist. Write operations can not be performed for a reference drive. This disk is consistent. It is not necessary to restore a disk. No disk has been inserted. Drive specified is not removable. Inserted disk is unformatted. Disk specified is read-only. Disk restoring is canceled. The process is being canceled because this system is required to shut down. The process is interrupted by the power supply cut off.

Causes

Remedies
Ensure that the specified drive has been connected correctly. Restart this system and retry. Restart this system and retry. Ensure that the drive specified has been connected correctly. It is possible that the disk is broken or write-protected. Insert another disk and retry. Ensure that the specified drive has been connected correctly. Confirm the inserted disk. Restart this system and retry. Restart this system and retry. Insert a disk for management. Ensure that the specified drive has been connected correctly. Use a drive for storage.

Remarks

Insert a disk. Ensure that the specified drive has been connected correctly. Exchange disks and format. Insert a writable disk. Restart this system and retry. Restart this system and retry.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-40

Appx MT1-41
Event
11557 11558 11559 11560 11561 11562 11563 11564 11565 11566 11567 11568 11569 11570 11571 11572 11573 11574 11575 11576 11577 11578 11579 11580 11581

Event Source
FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Description
Free disk space is insufficient. Disk storing failed. Drive specified does not exist. Inserted disk is write-protected. Disk locking failed. Disk unlocking failed. This disk is consistent. It is not necessary to restore a disk. The disk is illegal. The disk has been exchanged. Write operations can not be performed for a reference drive. No disk has been inserted. Drive specified is not removable. Inserted disk is unformatted. Interrupted the processing of database rebuilding. The process is being canceled because this system is required to shut down. The process is interrupted by the power supply cut off. Data in the disk is inconsistent. The inserted disk is a new (unused) disk. Drive specified does not exist. Disk locking failed. The hard disk is full. Storing images in read-only disk was requested. The drive is in use. No disk is inserted. The drive is not removable.

Causes

Remedies
Confirm the inserted disk. Confirm the inserted disk. Ensure that the specified drive has been connected correctly. Confirm the inserted disk. Check the disk drive status. Check the disk drive status.

Remarks

Confirm the inserted disk. Retry from the beginning. Use a drive for storage. Insert a disk. Ensure that the specified drive has been connected correctly. Confirm the inserted disk. Some selected studies may already have been registered. Restart this system and retry. Restart this system and retry. Restore the disk. Confirm the inserted disk. Ensure that the specified drive has been connected correctly. Check the disk drive status.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-41

Appx MT1-42
Event
11582 11583 11584 11585 11586 11587 11588 11589 11590

Event Source
FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Description
The disk has been already formatted. The disk is not formatted. The disk is read-only. Disk specified is not inserted. The requested processing has been canceled. The process has been canceled. The process is interrupted by the power supply cut off. Data in the disk is inconsistent. (DICOMDIR) Image information in the disk is illegal. Format is not allowed under system settings. Free disk space is insufficient. Inserted disk is not a new (unused) disk. There are no targeted images in this disk. Inserted disk is a new (unused) disk. Disk specified is not for management.

Causes

Remedies

Remarks

The disk cannot be used. Eject and confirm it. Use a formatted disk. If you wish to format disks on this system, contact your service engineer.

The structure within The disk is illegal or The information is insufficient. It is necessary to send an inquiry to a device that created The disk. Use the disk format setup function of the Service Utility to select OS or Dedicated application.

11591 11592 11593 11594 11595 11596 11597

FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Change to a correct disk.

The target image is not stored on the disk inserted by the user.

Disk storing failed. Possible Eject the disk, conform it and retry. causes are: Contact your service engineer if the (1) The disk is broken same symptom recurs even after it has (2)  The disk drive is not connected been retried. correctly. Disk formatting failed. System Contact your service engineer. settings may have been incorrect. Drive specified does not exist. System settings may have been incorrect. Contact your service engineer.

No data can be written onto the medium because it is broken. The drive is broken. Although Dedicated application is selected for disk format setup from the Service Utility, the format tool filename or path is incorrectly set. The disk drive path for the Service Utility is not properly set.

11598

FFCustomMsgBox

11599

FFCustomMsgBox

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-42

Appx MT1-43
Event
11600 11601

Event Source
FFCustomMsgBox FFCustomMsgBox

Description
The disk is write-protected. Disk locking failed.

Causes
Ensure that the disk drive has been connected correctly and retry. Contact your service engineer if the same symptom recurs even after it has been retried. Carry it out again after a while. Contact your service engineer if the same symptom recurs even after it has been retried.

Remedies
This error could not normally occur.

Remarks

11602

FFCustomMsgBox

Disk unlocking failed. The disk drive may have been in use.

Check whether the drive is accessed, for instance, by explorer. Check whether the drive is accessed, for instance, by explorer.

11603

FFCustomMsgBox

An error occurred in an attempt to Carry it out again after a while. eject disk. The disk drive may Contact your service engineer if the have been in use. same symptom recurs even after it has been retried. The disk needs to be rebuilt. The disk structure is incorrect or some files are broken. Image information in the disk is illegal. The process is either discontinued or continued excluding certain files. The disk cannot be used. Eject, confirm it and retry. Contact your service engineer if the same symptom recurs even after it has been retried. The disk cannot be used. Eject, confirm it and retry. Contact your service engineer if the same symptom recurs even after it has been retried. Eject the disk, confirm it and retry. Contact your service engineer if the same symptom recurs even after it has been retried. Eject the disk, confirm it and retry. Contact your service engineer if the same symptom recurs even after it has been retried. Set another label name and retry. Contact your service engineer if the same symptom recurs even after it has been retried.

11604 11605 11606

FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

The disk is partly broken. This error could not normally occur.

11607

FFCustomMsgBox

Image information in the disk is illegal.

This error could not normally occur.

11608

FFCustomMsgBox

The disk has been exchanged.

This error could not normally occur.

11609

FFCustomMsgBox

Failed in obtaining information in the disk. Some images failed in acquiring. Same label name already exists.

An internal logic error has occurred.

11610 11611

FFCustomMsgBox FFCustomMsgBox

This error could not normally occur.

11612 11613

FFCustomMsgBox FFCustomMsgBox

The disk needs to be rebuilt. Drive specified is not removable. Ensure that the specified drive has been connected correctly.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-43

Appx MT1-44
Event
11615 11617 11620 11621

Event Source
FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Description
The disk is illegal. No disk has been inserted.

Causes

Remedies
Confirm the inserted disk. Insert a disk and retry. HtmlView.exe is not installed at the correct location. It is necessary to perform a reinstallation. The cause of this error is unknown. If The same error recurs after a restart, send feedback to the design personnel.

Remarks

Failed in starting HtmlView Contact your service engineer. window. Installation may not have been finished successfully. Failed in terminating HtmlView window. Failed in terminating HtmlView window. Failed in accessing files within the disk. It is possible that some files are damaged. No image storage disk is registered. The disk cannot be recognized. ErrorCode:01 SourceFile:CPreset.cs SpotCode:2 Preset registration num is full. [11629] Disk unidentified. Preset registration num is full. Restart the server computer. Contact your service engineer if the same symptom recurs even after it has been restarted.

11622

FFCustomMsgBox

Press the button below to continue other This error could not normally occur. processes. The operation can be continued. If the same error recurs, send feedback to the design personnel. Contact your service engineer. Rebuild the disk, and restore database from the disk. Check contents of the disk. Format it as necessary and reinsert. There is no operational problem. (There is not operation fault even in case of output.) (Not used.) Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

11627 11628 11629 11711

FFCustomMsgBox FFCustomMsgBox CustomMsgBoxCom FFPresetData AccessCom FFInputEz

11900

%1 : Registry Value Get/Set Error Information was not successfully acquired from the registry. [Key] %2 [Exp] %3 %4 %5 %1 : Database Connection Error [DB] %2 [Exp] %3 %4 %5

11901

FFInputEz

An attempt to establish the connection to a Check whether the SQL service manager database failed. is operating normally. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. A database information acquisition or storage failed. Restart the server application and client (Not used.) application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

11902

FFInputEz

%1 : Database Data Get/Set Error [DB] %2 [Table] %3 [Field] %4 [Exp] %5

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-44

Appx MT1-45
Event
11903

Event Source
FFInputEz

Description
%1 : DDO Data Get/Set Error [Tag] %2 %3 %4 %5 %1 : Other Error [Procedure] %2 [ErrorCode] %3 [Exp] %4 %5

Causes
The information acquisition/storage operation was not successfully performed in relation to the image information file (DDO). Abnormal patient information was transmitted from the receipt computer, or the transmitted patient information was not successfully operated on.

Remedies
Restart the server application and client (Not used.) application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. This problem may be solved when an automatic retry is performed by the application. Check whether the network is disconnected. Check for improper patient information. If the patient information is improper, correct it and transmit the corrected patient information from the receipt computer. It is possible that unsupported patient information was transmitted from the receipt computer. Check the operation performed by the receipt computer. If the above cure does not work, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Check whether the patient information is abnormal. If it is abnormal, correct it and transmit the corrected patient information from the receipt computer. It is possible that unsupported patient information was transmitted from the receipt computer. Check the operation performed by the receipt computer. If the above cure does not work, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Check to see if the filename is correct or available hard disk space is sufficient. Proceed with processing. Proceed with processing.

Remarks

11904

FFInputEz

11905

FFInputEz

%1 :Patient Information Error %2%[DATA]n %3%[Exp]n %4 %5

Abnormal patient information was transmitted from the receipt computer.

12001 FF32

[%1] It failed in CreateFile (%2). %3 [%1] It failed in CreateFileMapping (%2). %3 [%1] It failed in MapViewOfFile (%2). %3 [%1] It failed in CreateCompatibleDC. %2

Failed in reading a bitmap file. It is conceivable that there was no such file, free disk space was not sufficient or the system was unstable. File map object generation failed. This failure is attributable to resource insufficiency or system instability. File map object generation failed. This failure is attributable to resource insufficiency or system instability. Failed in creating a device context. It is conceivable that available resources were insufficient or the system was unstable.

[%1]: Instance name [%2]: Error code [%3]: Filename/mutex [%1]: Instance name [%2]: Error code [%3]: Filename/mutex [%1]: Instance name [%2]: Error code [%3]: Filename/mutex [%1]: Instance name [%2]: Error code [%3]: Filename/mutex

12002 FF32

12003 FF32 12004 FF32

Proceed with processing. Proceed with processing.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-45

Appx MT1-46
Event Event Source Description Causes Remedies Remarks
[%1]: Instance name [%2]: Error code [%3]: Filename/mutex [%1]: Instance name [%2]: Error code [%3]: Filename/mutex [%1]: Instance name [%2]: Error code [%3]: Filename/mutex 12005 FF32 12006 FF32 [%1] A DIB section was not successfully Proceed with processing. It failed in CreateDIBSection (%2). created. The error is attributable to %3 resource insufficiency or system instability. [%1] It failed in OleCreatePictureIndirect (%2). %3 [%1] Exception error. (%2). %3 Failed in creating a bitmap picture object. It is conceivable that available resources were insufficient or the system was unstable. An exceptional error occurred. Proceed with processing.

12007 FF32

The program might be faulty. Check the operations performed before and after the error occurrence, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Processing will be continued. Check to see if the filename is correct or available hard disk space is sufficient. Proceed with processing. Proceed with processing.

12008 FF32

[%1] It failed in ExtractIcon. %2 [%1] It failed in OleCreatePictureIndirect (%2). %3 [%1] Exception error. (%2). %3 [%1] It is a file path error. %2 [%1] Memory allocation failed (%2). %3 [%1] Exception error. (%2).

The icon file was not successfully loaded. The error is attributable to a nonexistent file, disk space insufficiency, or system instability. The icon picture object was not successfully created. The error is attributable to resource insufficiency or system instability. An exceptional error occurred. The file path was illegal. Memory allocation failed. This error is attributable to resource insufficiency or system instability. An exceptional error occurred.

[%1]: Instance name [%2]: Error code [%3]: Filename/mutex [%1]: Instance name [%2]: Error code [%3]: Filename/mutex [%1]: Instance name [%2]: Error code [%3]: Filename/mutex [%1]: Instance name [%2]: Error code [%3]: Filename/mutex [%1]: Instance name [%2]: Error code [%3]: Filename/mutex [%1]: Instance name [%2]: Error code [%3]: Filename/mutex

12009 FF32

12010 FF32 12011 FF32

The program might be faulty. Check the program. Processing will be continued. Check to see if the filename is correct. Proceed with processing. Check whether the filename is correct. Processing will be continued. The program might be faulty. Check the operations performed before and after the error occurrence, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Processing will be continued. Check the data fed from the endoscope.

12012 FF32 12013 FF32

12016 ImportImageFolder AccessCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Arbitrary Error Details.

Data is illegal.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-46

Appx MT1-47
Event Event Source Description
FF32 [FFCheckApplication Error] OPApplication key check error. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not get Indicator-icon status from Event Object.

Causes
The option key (OpApplication) for application identification has not been installed. The indicator status information was not successfully acquired.

Remedies
It is possible that installation could not be completed correctly. Perform a reinstallation after uninstalling. There is no operational problem.

Remarks

12020 FF32 12103 FCRWeb

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

12114

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Can not get the RU-device-status from database.

The RU device status information was not successfully acquired. An internal system error occurred.

Restart both the server application and client application. If the same error recurs, perform a reinstallation.

12116

FCRWeb

ErrorCode:%1%nSubSystem:%2 An RU operation failed. An internal system Restart both the server application and %nSourceFile: %3%nSpotCode: error occurred. client application. If the same error recurs, %4%nDB Error: Can not register perform a reinstallation. RU-control-command to database.

12118

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Can not get the RU-device-info from database.

The RU internal information was not successfully acquired. An internal system error occurred.

Restart both the server application and client application. If the same error recurs, perform a reinstallation.

12119

FCRWeb

ErrorCode:%1%nSubSystem:%2 RU device exclusive control was not %nSourceFile: %3%nSpotCode: successfully ended. An internal system %4%nDB Error: Can not release error occurred. RU-exclusive-info on database when RU-control command failed.

Restart both the server application and client application. If the same error recurs, perform a reinstallation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-47

Appx MT1-48
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not send response to RU-error-dialog.

Causes
A window display request was not successfully answered. An internal system error occurred.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

12121 FCRWeb

12123 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Can not get RU-control-result from database.

The RU operation was not successfully monitored. An internal system error occurred.

Check that the RU is not performing a process, and then restart both the server application and client application.

12124 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Can not release RU-exclusive-info on database when RU-control command completed.

Exclusive control was not successfully ended after RU monitoring. An internal system error occurred.

Restart both the server application and client application. If the same error recurs, perform a reinstallation.

12126 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nRU-control-result not found on database. RU-control may be cancelled by other process.

The RU operation was not successfully monitored. It is conceivable that the RU operation was canceled by another process.

Check that the RU is not performing a process, and then restart both the server application and client application.

12127 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nSpecified RU is in-use by other user/process.

The specified RU was being used by another user.

Wait until the RU process terminates, and then try again.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-48

Appx MT1-49
Event Event Source Description Causes Remedies Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). 12128 FCRWeb ErrorCode:%1%nSubSystem:%2 The RU cannot be operated because a Open the RU status window and return a %nSourceFile: %3%nSpotCode: window display request is currently issued. response to the window display request. %4%nRU status error: RU-controlcommand invalid when RU-errordialog displayed.

12134 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Can not get the media-status from database.

Media status acquisition failed. An internal system error occurred.

Restart both the server application and client application. If the same error recurs, perform a reinstallation.

12135 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Can not get the media-list-info from database.

The storage disk list was not successfully acquired. An internal system error occurred.

Restart both the server application and client application. If the same error recurs, perform a reinstallation.

12140 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Can not get printer-info from database.

The printer information was not successfully acquired. An internal system error occurred.

Restart both the server application and client application. If the same error recurs, perform a reinstallation.

12146 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not get the outputqueue-info from database.

The output queue information was not Restart both the server PC and client PC successfully acquired. This error is attributable to an inactive server application or a deactivated database.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-49

Appx MT1-50
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not operate the specified output-queue.

Causes

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

12148 FCRWeb

An attempt to register information in a Restart both the server application and database failed. The problem is attributable client application. If the same error recurs, to a database timeout or other database perform a reinstallation. error.

12155 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not get the specified event-info.

The event information was not successfully Restart both the server application and acquired. The database might be client application. If the same error recurs, damaged. perform a reinstallation.

12157 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not update the status of specified event-info.

The error status was not successfully Restart both the server application and updated. The database might be damaged. client application. If the same error recurs, perform a reinstallation.

12162 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Can not connect to NetConfig database.

An error occurred when an attempt was made to access a NetConfig.mdb file. The file might be damaged.

Restart both the server application and client application. If the same error recurs, perform a reinstallation.

12163 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Can not disconnect from NetConfig database.

NetConfig was not successfully disconnected.

Restart both the server application and client application. If the same error recurs, perform a reinstallation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-50

Appx MT1-51
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Can not get specified System-Configuration from database.

Causes
The system settings were not successfully acquired. An internal system error occurred.

Remedies
The process will be continued by using default values.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

12173 FCRWeb

12174 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Can not get specified System-Configuration from database (Value is not Setup).

The system settings could not be acquired. The process will be continued by using No values were set as the system settings. default values. Set appropriate values as the system settings.

12176 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not get the specified directory-info from Directory.ini file.

An attempt to acquire information from the Directory.ini file failed. The error is attributable to a nonexistent file or a damaged file.

Check the Diretory.ini file, and then restart the server application.

12178 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not get the specified registry value (DWORD).

Registry data was not successfully acquired due to an exception error.

The process will be continued by using default values.

12180 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Can not connect to LangMsgBox database.

The file was not successfully acquired from Restart both the server application and LangMsgBox.mdb. The error is attributable client application. If the same error recurs, to a nonexistent file or a damaged file. perform a reinstallation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-51

Appx MT1-52
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not get the specified Message String.

Causes
Message acquisition failed. The LangMsgBox.mdb file might be damaged.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

12181 FCRWeb

12185 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not get User-ID on the basis of Login-User-ID.

User ID acquisition failed due to an exception error.

There is no operational problem. Processing will be continued.

12186 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: % 4%nOperation-logging failed.

The operation log was not successfully written due to an exception error.

Restart both the server application and client application. If the same error recurs, perform a reinstallation.

12188 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not register operationlog.

The operation log was not successfully written due to an exception error.

Restart both the server application and client application. If the same error recurs, perform a reinstallation.

12190 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Can not get specified message-string from database.

The character string was not successfully acquired. This failure is attributable to a database timeout or other database error.

The process will be continued by using default values.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-52

Appx MT1-53
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDB Error: Specified message-string not found.

Causes
No character string is set.

Remedies
The process will be continued by using default values.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

12191 FCRWeb

12201 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not send response to RU-error-dialog (Already responded).

A response was already made to the RU.

Wait for a while, click the Update button to refresh the window, and continue the operation.

12202 FCRWeb

ErrorCode:%1%nSubSystem:%2 The response is completed. %nSourceFile: %3%nSpotCode: %4%nCan not send response to RU-error-dialog (Already deleted).

Click the Update button to refresh the window, and continue the operation.

12219 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nSpecified output-queue overlapped.

The specified output queue operation is already registered.

There is no operational problem.

12224 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not update the status of specified event-info (Already deleted).

The selected event information was already deleted.

Refresh the window and continue the operation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-53

Appx MT1-54
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not get the specified registry value (SZ).

Causes
Registry data was not successfully acquired due to an exception error.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

12225 FCRWeb

12400 FCRWeb

ErrorCode:%1%nSubSystem:%2 The patient information was not Restart. If the same symptom recurs, %nSourceFile: %3%nSpotCode: successfully acquired. The database might perform a reinstallation. %4%nIt failed in the acquisition of be damaged. patient information.

12401 FCRWeb

ErrorCode:%1%nSubSystem:%2 The patient information was not %nSourceFile: %3%nSpotCode: successfully registered. The database %4%nIt failed in the registration of might be damaged. patient information.

Restart. If the same symptom recurs, perform a reinstallation.

12402 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the update of patient information.

The patient information was not successfully updated. The database might be damaged.

Restart. If the same symptom recurs, perform a reinstallation.

12403 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the deletion of patient information.

The patient information was not successfully deleted. The database might be damaged.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-54

Appx MT1-55
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the IP use frequency list acquisition.

Causes
The IS use count list was not successfully acquired. The database might be damaged.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

12404 FCRWeb

12405 FCRWeb

ErrorCode:%1%nSubSystem:%2 The user information was not successfully %nSourceFile: %3%nSpotCode: acquired. The database might be %4%nIt failed in the acquisition of damaged. user information.

Restart. If the same symptom recurs, perform a reinstallation.

12406 FCRWeb

ErrorCode:%1%nSubSystem:%2 The user information list was not Restart. If the same symptom recurs, %nSourceFile: %3%nSpotCode: successfully acquired. The database might perform a reinstallation. %4%nIt failed in the acquisition of be damaged. the user information list.

12407 FCRWeb

ErrorCode:%1%nSubSystem:%2 The user information list was not Restart. If the same symptom recurs, %nSourceFile: %3%nSpotCode: successfully acquired. The database might perform a reinstallation. %4%nIt failed in the registration of be damaged. user information.

12408 FCRWeb

ErrorCode:%1%nSubSystem:%2 The user information was not successfully %nSourceFile: %3%nSpotCode: acquired. The database might be %4%nIt failed in the acquisition of damaged. user information.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-55

Appx MT1-56
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the update of user information.

Causes

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

12409 FCRWeb

The user information was not successfully Restart. If the same symptom recurs, updated. The database might be damaged. perform a reinstallation.

12410 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the deletion of user information.

The user information was not successfully Restart. If the same symptom recurs, updated. The database might be damaged. perform a reinstallation.

12411

FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the order preservation.

The sequence was not successfully stored. Restart. If the same symptom recurs, The database might be damaged. perform a reinstallation.

12412 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe image cannot be deleted. The error occurred while demanding the image deletion.

The image could not be deleted. An error occurred when an image deletion request was issued. This is an internal system error.

Restart. If the same symptom recurs, perform a reinstallation.

12413 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the addition of the image.

Image addition failed. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-56

Appx MT1-57
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the URL acquisition of the paper print setting site.

Causes
The URL of the paper print setup site was not successfully acquired. The database might be damaged.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

12414 FCRWeb

12415 FCRWeb

ErrorCode:%1%nSubSystem:%2 The explanatory information was not %nSourceFile: %3%nSpotCode: successfully registered. The database %4%nIt failed in the registration of might be damaged. explanation information.

Restart. If the same symptom recurs, perform a reinstallation.

12416 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the update of explanation information.

The explanatory information was not successfully updated. The database might be damaged.

Restart. If the same symptom recurs, perform a reinstallation.

12417 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the deletion of explanation information.

The explanatory information was not successfully deleted. The database might be damaged.

Restart. If the same symptom recurs, perform a reinstallation.

12418 FCRWeb

ErrorCode:%1%nSubSystem:%2 The study access history was not Restart. If the same symptom recurs, %nSourceFile:%3%nSpotCode:% successfully acquired. The database might perform a reinstallation. 4%nIt failed in the acquisition of be damaged. the change history.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-57

Appx MT1-58
Event Event Source Description Causes Remedies Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). 12419 FCRWeb ErrorCode:%1%nSubSystem:%2 The transmission history was not Restart. If the same symptom recurs, %nSourceFile: %3%nSpotCode: successfully acquired. The database might perform a reinstallation. %4%nIt failed in the acquisition of be damaged. the transmission history.

12420 FCRWeb

ErrorCode:%1%nSubSystem:%2 A database connection error occurred. %nSourceFile: %3%nSpotCode: The database might not be running. %4%nIt is a data base connection error.

Restart. If the same symptom recurs, perform a reinstallation.

12421 FCRWeb

ErrorCode:%1%nSubSystem:%2 The operating privileges were not Restart. If the same symptom recurs, %nSourceFile: %3%nSpotCode: successfully acquired. The database might perform a reinstallation. %4%nIt failed in the acquisition of be damaged. the operation authority.

12422 FCRWeb

ErrorCode:%1%nSubSystem:%2 The operating privileges were not %nSourceFile: %3%nSpotCode: successfully updated. The database might %4%nIt failed in the update of the be damaged. operation authority.

Restart. If the same symptom recurs, perform a reinstallation.

12423 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the replacement of the disk.

Disk changeover failed. An internal system Restart. If the same symptom recurs, error occurred. perform a reinstallation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-58

Appx MT1-59
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the format of the disk.

Causes
Disk formatting failed. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

12424 FCRWeb

12425 FCRWeb

ErrorCode:%1%nSubSystem:%2 Disk recovery failed. An internal system %nSourceFile: %3%nSpotCode: error occurred. %4%nIt failed in the restoration of the data base.

Restart. If the same symptom recurs, perform a reinstallation.

12426 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the disk setting.

Disk setup failed. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

12427 FCRWeb

ErrorCode:%1%nSubSystem:%2 Disk recovery failed. An internal system %nSourceFile: %3%nSpotCode: error occurred. %4%nIt failed in the restoration of the disk.

Restart. If the same symptom recurs, perform a reinstallation.

12428 FCRWeb

ErrorCode:%1%nSubSystem:%2 The explanatory information was not Restart. If the same symptom recurs, %nSourceFile: %3%nSpotCode: successfully acquired. The database might perform a reinstallation. %4%nIt failed in the acquisition of be damaged. explanation information.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-59

Appx MT1-60
Event Event Source Description Causes Remedies Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). 12429 FCRWeb ErrorCode:%1%nSubSystem:%2 The equipment name was not successfully Restart. If the same symptom recurs, %nSourceFile: %3%nSpotCode: acquired. The database might be perform a reinstallation. %4%nIt failed in the acquisition of damaged. the device name.

12430 FCRWeb

ErrorCode:%1%nSubSystem:%2 The log-in history was not successfully %nSourceFile:%3%nSpotCode:% acquired. The database might be 4%nIt failed in the acquisition of damaged. the login history.

Restart. If the same symptom recurs, perform a reinstallation.

12431 FCRWeb

ErrorCode:%1%nSubSystem:%2 An attempt to acquire a backup history %nSourceFile:%3%nSpotCode:% failed. The database might be damaged. 4%nIt failed in the acquisition of the backup history.

Restart. If the same symptom recurs, perform a reinstallation.

12900 FFInputEz

%1 : Registry Value Get/Set Error Information was not successfully acquired [Key] %2 from the registry. [Exp] %3 %4 %5 %1 : Database Connection Error [DB] %2 [Exp] %3 %4 %5

Restart the server application and client (Not used.) application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

12901 FFInputEz

(Not used.) An attempt to establish the connection to a Check whether the SQL service manager database failed. is operating normally. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client (Not used.) application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

12902 FFInputEz

%1 : Database Data Get/Set Error A database information acquisition or [DB] %2 storage failed. [Table] %3 [Field] %4 [Exp] %5

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-60

Appx MT1-61
Event Event Source Description
%1 : DDO Data Get/Set Error [Tag] %2 %3 %4 %5 %1 : Other Error [Procedure] %2 [ErrorCode] %3 [Exp] %4 %5 It failed that [%1] gets the FontName It failed that [%1] gets the FontName Socket error (INVALID_SOCKET) (%1).%n[%2] It failed that [%1] gets the FontSize It failed that [%1] gets the FontSize Socket error[%1]

Causes
The information acquisition/storage operation was not successfully performed in relation to the image information file (DDO). The internal setup information was not successfully acquired.

Remedies
Restart the server application and client (Not used.) application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. There is no operational problem (garbled characters may be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL. There is no operational problem (garbled characters may be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL.

Remarks

12903 FFInputEz

12904 FFInputEz

13000 FFIdMenuChange 13000 FFIdMenuItem 13001 FFIdConnection Watch 13001 FFIdMenuChange 13001 FFIdMenuItem 13001 FFIdRuMainControl 13001 FFIdConnection WatchEx 13001 FFIdRuMain ControlEx 13001 FFInput 13001 FFLogFile

The Font key was not found in the registry. The Font key was not found in the registry. Program error.

The FontSizeSS/FontSizeS/FontSizeM There is no operational problem (garbled /FontSizeL/FontSizeLL key was not characters may be displayed). If you feel found in the registry. uncomfortable, reinstall the CR-IR 391CL. The FontSizeSS/FontSizeS/FontSizeM There is no operational problem (garbled /FontSizeL/FontSizeLL key was not characters may be displayed). If you feel found in the registry. uncomfortable, reinstall the CR-IR 391CL. Program error.

Socket Error (INVALID_SOCKET) Program error. Message [%1] Error Code [%2] Socket Error (INVALID_SOCKET) Program error. Message [%1] Error Code [%2] It failed that [%1] gets the FontName [%1] It failed in CreateFile (%2). %3 MessageBox DataBase Connection Error. [%1] The Font key was not found in the registry. Log file creation was unsuccessful. The problem might have been caused, for instance, by an invalid filename selection, inadequate disk space, or system instability. The message database was not successfully connected. It is conceivable that the database did not exist or that the specified data source name was invalid. There is no operational problem (garbled characters may be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL. Check the disk for a free space, or restart the server PC. [%1]: Instance name [%2]: Error code [%3]: Filename/mutex

13001 FFCustomMsgBox

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-61

Appx MT1-62
Event Event Source Description
Image Database Access Failure. ErrNo:%1 NativeErrNo:%2 SQLState:%3 Source:%4 Description:%5

Causes

Remedies

Remarks
[%1, %2, %3, %4, %5]: Detailed information

13001 FFImageDBCTL

The image database was not successfully Restart the server computer. accessed (an ADO related error occurred).

13001 FF32LIB

FF32lib Database Access An attempt to access the database failed. Failure.%nFunction:%1 Command:%2%nErrNo:%3 NativeErrNo:%4 SQLState:%5%n Source:%6%nDescription:%7 An error occurred when an attempt was NetConfig Database Access made to access a database. Failure.%nErrNo:%1 NativeErrNo:%2 SQLState:%3%n Source:%4%nDescription:%5 Bind error (INVALID_SOCKET) (%1).%n[%2] It failed that [%1] gets the multibyte flag It failed that [%1] gets the multibyte flag Bind error[%1] Bind Error (INVALID_SOCKET) Message [%1] Error Code [%2] Bind Error (INVALID_SOCKET) Message [%1] Error Code [%2] It failed that [%1] gets the FontSize [%1] It failed in CreateFileMapping (%2). MessageBox Data Get Error. [%1] %2 Image Database Access Failure. InstanceName[%1] %2 Program error. The Multibyte key was not found in the registry. The Multibyte key was not found in the registry. Program error. Program error. Program error.

Restart the server computer.

[%1, %2, %3, %4, %5]: Detailed information

13001 FFNetDB

Restart the server computer.

[%1, %2, %3, %4, %5]: Detailed information

13002 FFIdConnection Watch 13002 FFIdMenuChange 13002 FFIdMenuItem 13002 FFIdRuMainControl 13002 FFIdConnection WatchEx 13002 FFIdRuMain ControlEx 13002 FFInput 13002 FFLogFile 13002 FFCustomMsgBox

Reinstall the system. Reinstall the system.

The FontSizeSS/FontSizeS/FontSizeM There is no operational problem (garbled /FontSizeL/FontSizeLL key was not characters may be displayed). If you feel found in the registry. uncomfortable, reinstall the CR-IR 391CL. File map object generation failed. This failure is attributable to resource insufficiency or system instability. The specified message was not found in the database. The message was not registered in the database, or the ID was incorrectly specified (due to a program fault). The image database was not successfully accessed. Restart the server computer. Perform a reinstallation or install the latest message database again. [%1]: Instance name [%2]: Error code [%3]: Filename/mutex

13002 FFImageDBCTL 13002 FF32LIB 13002 FFNetDB

Restart the server computer. Restart the server computer. Restart the server computer.

[%1, %2, %3, %4, %5]: Detailed information [%1, %2, %3, %4, %5]: Detailed information [%1, %2, %3, %4, %5]: Detailed information

FF32lib Database Access Failure. An attempt to access the database failed. InstanceName[%1]%n%2%n Function:%3 Command:%4 NetConfig Database Access An error occurred when an attempt was Failure. InstanceName[%1]%n%2 made to access a database.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-62

Appx MT1-63
Event Event Source Description
Listen error (INVALID_SOCKET) (%1).%n[%2] [%1] failed in the initialization for the display group data acquisition Image Folder Path Get Error Listen error[%1] Listen Error (INVALID_SOCKET) Message [%1] Error Code [%2] Listen Error (INVALID_SOCKET) Message [%1] Error Code [%2] It failed that [%1] gets the multibyte flag [%1] It failed in MapViewOfFile (%2). Same MessageBox Existed. [%1] Image Database Access Failure. InstanceName[%1] %2 %3 Program error. The DisplayDataDB key was not found in Reinstall the system. Directory.ini or the connection character string was not properly registered in the display group table. The Bitmap key was not found in Directory.ini. Program error. Program error. Program error. The Multibyte key was not found in the registry. File mapping failed. This error is attributable to resource insufficiency or system instability. The specified message box is already displayed. The image database was not successfully accessed. Reinstall the system. Restart the server computer. Close the displayed message box. Restart the server computer. [%1, %2, %3, %4, %5]: Detailed information [%1, %2, %3, %4, %5]: Detailed information (Not used.) [%1, %2, %3, %4, %5]: Detailed information [%1]: Instance name [%2]: Error code [%3]: Filename/mutex Reinstall the system.

Causes

Remedies

Remarks

13003 FFIdConnection Watch 13003 FFIdMenuChange

13003 FFIdMenuItem 13003 FFIdRuMainControl 13003 FFIdConnection WatchEx 13003 FFIdRuMain ControlEx 13003 FFInput 13003 FFLogFile 13003 FFCustomMsgBox 13003 FFImageDBCTL

13003 FF32LIB 13003 FFNetDB 13004 FFIdConnection Watch 13004 FFIdMenuChange

FF32lib Database Access Failure. An attempt to access the database failed. InstanceName[%1]%n%2%n%3 NetConfig Database Access Failure. InstanceName[%1]%n%2%n%3 Accept error (%1).%n[%2] [%1] failed in the display group data acquisition [Miss] Image Get Error An error occurred when an attempt was made to access a database. Program error.

Restart the server computer. Restart the server computer.

The DisplayDataDB key was not found in Reinstall the system. Directory.ini or the connection character string was not properly registered in the display group table. Id_MissExposure_I.bmp was not found in There is no operational problem (the button the path to an image folder or the image might not normally be displayed). format was illegal. If you feel uncomfortable, reinstall the CR-IR 391CL. Program error. Program error.

13004 FFIdMenuItem

13004 FFIdRuMainControl 13004 FFIdConnection WatchEx


020-221-01E 04.28.2009 FM5535

Accept error[%1] Accept Error Message [%1] Error Code [%2]

CR-IR 391CL Service Manual

Appx MT1-63

Appx MT1-64
Event Event Source Description
Accept Error Message [%1] Error Code [%2] It failed that [%1] gets the connection string of STR DB [%1] It failed in CreateMutex (%2). %3 Program error. The LangStrDB key was not found in Directory.ini. Mutex creation failed. This failure is attributable to resource insufficiency or system instability. Reinstall the system. Restart the server computer. Restart the server computer. [%1]: Instance name [%2]: Error code [%3]: Filename/mutex

Causes

Remedies

Remarks

13004 FFIdRuMain ControlEx 13004 FFInput 13004 FFLogFile 13004 FFCustomMsgBox 13005 FFIdConnection Watch 13005 FFIdMenuChange 13005 FFIdRuMainControl 13005 FFIdConnection WatchEx 13005 FFIdRuMain ControlEx 13005 FFInput 13005 FFCustomMsgBox 13006 FFIdConnection Watch 13006 FFIdDepartSelect 13006 FFIdMenuChange 13006 FFIdRuMainControl 13006 FFIdConnection WatchEx 13006 FFIdRuMain ControlEx 13006 FFInput

MessageBox Dialog Create Error. The message box could not be generated. [%1] This error is attributable to resource insufficiency or system instability. Recv error (%1).%n[%2] [%1] failed in the liberating processing of the display group data acquisition Recv error[%1] Recv Error Message [%1] Error Code [%2] Recv Error Message [%1] Error Code [%2]

The connection to the RU was closed or an Restore the RU connection to normal. error occurred in the connection. The connection to the display group table was not successfully closed. Restart. If the same symptom recurs, perform a reinstallation.

The connection to the RU was closed or an Check the connection to the RU. error occurred in the connection. The connection to the RU was closed or an Restore the RU connection to normal. error occurred in the connection. The connection to the RU was closed or an Restore the RU connection to normal. error occurred in the connection.

Reinstall the system. It failed that [%1] connects to STR The connection character string was not DB properly registered for the LangStrDB key in Directory.ini. MessageBox Dialog Show Error. [%1] CloseSocekt error (%1).%n[%2] It failed that [%1] finds corresponding record [%1] failed in the initialization for the display menu data acquisition CloseSocekt error[%1] Socket Close Error Message [%1] Error Code [%2] Socket Close Error Message [%1] Error Code [%2] It failed that [%1] gets the connection string of SYS DB The message box could not be generated. This error is attributable to resource insufficiency or system instability. Program error. Program error. The DisplayDataDB key was not found in Reinstall the system. Directory.ini. Program error. Program error. Program error. The SysConfigDB key was not found in Directory.ini. Reinstall the system. Restart the server computer.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-64

Appx MT1-65
Event Event Source Description
List For Modaless MessageBox Management New Error. [%1] CreateThread error (%1).%n[%2] [%1] failed in the acquisition of number of records of display menu data CreateThread error[%1] Thread Create Error Message [%1] Error Code [%2] Thread Create Error Message [%1] Error Code [%2]

Causes
The modeless message box management table was not successfully created. This error is attributable to resource insufficiency or system instability. Program error. The connection character string was not properly registered in the display group table. Program error. Program error. Program error.

Remedies
Restart the server computer.

Remarks

13006 FFCustomMsgBox

13007 FFIdConnection Watch 13007 FFIdMenuChange 13007 FFIdRuMainControl 13007 FFIdConnection WatchEx 13007 FFIdRuMain ControlEx 13007 FFInput 13008 FFIdMenuChange 13008 FFIdRuMainControl 13008 FFIdConnection WatchEx 13008 FFIdRuMain ControlEx 13008 FFInput 13008 FFCustomMsgBox 13009 FFIdConnection Watch 13009 FFIdMenuChange 13009 FFIdRuMainControl 13009 FFIdConnection WatchEx 13009 FFIdRuMain ControlEx

Reinstall the system.

It failed that [%1] connects to SYS The connection character string was not DB properly registered for the SysConfigDB key in Directory.ini. [%1] failed in the display menu data acquisition Not Send Message Before Ack Returned [%1] Message Send Error Message [%1] Error Code [%2] Message Send Error [%1] WSAGetLastError = [%2] It failed that [%1] calls the CUSTOM MESSAGE BOX (%2) An exception error occurred. [%1] %2 LogFile Name Make error (%1).%n[%2] [%1] failed in the liberating processing of the display menu data acquisition LogFile Name Make error[%1] Log File Name Make Error Message [%1] Error Code [%2] Log File Name Make Error Message [%1] Error Code [%2]

Reinstall the system.

Not properly registered to the display group Reinstall the system. table. Program error. A connection error occurred. A connection error occurred. Restore the RU connection to normal. Restore the RU connection to normal.

The message database did not exist or the Reinstall the system. program was faulty. An exception error occurred. The Log key was not found in Directory.ini. The connection to the display menu table was not successfully closed. The Log key was not found in Directory.ini. The Log key was not found in Directory.ini. The Log key was not found in Directory.ini. Restart the server computer. Reinstall the system. Restart. If the same symptom recurs, perform a reinstallation. Reinstall the system. Register the Log key in Directory.ini. Register the Log key in Directory.ini.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-65

Appx MT1-66
Event Event Source Description
Common function error occurred. [%1] %2 It failed that [%1] gets the Patient Information DB Connect error (%1).%n[%2] [%1] failed in the termination of the display menu data acquisition DB Connect error[%1] DB Connect Error Message [%1] Error Code [%2] DB Connect Error Message [%1] Error Code [%2] It failed that [%1] initializes [%2]

Causes
The common function returned an error. Program error.

Remedies
Restart the server computer.

Remarks

13009 FFCustomMsgBox 13009 FFInput 13010 FFIdConnection Watch 13010 FFIdMenuChange 13010 FFIdRuMainControl 13010 FFIdConnection WatchEx 13010 FFIdRuMain ControlEx 13010 FFInput 13010 FFCustomMsgBox

SysConfigDB key was not found in Reinstall the system. Directory.ini or SysConfig.mdb did not exist in the specified path. The connection to the display menu table was not successfully closed. Restart. If the same symptom recurs, perform a reinstallation.

SysConfigDB key was not found in Reinstall the system. Directory.ini or SysConfig.mdb did not exist in the specified path. SysConfigDB key was not found in Properly register the SysConfigDB key in Directory.ini or SysConfig.mdb did not exist Directory.ini. in the specified path. SysConfigDB key was not found in Properly register the SysConfigDB key in Directory.ini or SysConfig.mdb did not exist Directory.ini. in the specified path. Program error. Restart the server computer.

ActiveX Data Objects (ADO) Error. The database was not successfully operated. ErroNo:%1 Source:%2 Description:%3 DB Read error (%1).%n[%2] The EchoInterval, ComBreakTimeout1 PortFrupStatus, or EnableLogFrupConnect key was not found in SysConfig.mdb. Program error.

13011

FFIdConnection Watch FFIdMenuChange FFIdRuMainControl FFIdConnection WatchEx FFIdRuMain ControlEx FFInput

Reinstall the system.

13011 13011 13011

The code of the specified group does not exist in [%1] DB Read error[%1] DB Read error Message [%1] Error Code [%2] DB Read error Message [%1] Error Code [%2]

The PortFrupMain, AckTimeout, or Reinstall the system. EnableLogFrupMain key was not found in SysConfig.mdb. The EchoInterval, ComBreakTimeout1 PortFrupStatus, or EnableLogFrupConnect key was not found in SysConfig.mdb. Ensure that the EchoInterval, ComBreakTimeout1, PortFrupStatus, and EnableLogFrupConnect keys are all registered in SysConfig.mdb.

13011 13011

The PortFrupMain, AckTimeout, or Ensure that the PortFrupMain, EnableLogFrupMain key was not found in AckTimeout, and EnableLogFrupMain SysConfig.mdb. keys are all registered in SysConfig.mdb. Reinstall the system.

It failed that [%1] gets the window The ScallHight/ScallWidth key was not size registered in the registry.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-66

Appx MT1-67
Event Event Source Description
DB Close error (%1).%n[%2] The code of the specified menu does not exist in [%1] DB Close error[%1] DB Close Error Message [%1] Error Code [%2] DB Close Error Message [%1] Error Code [%2] It failed that [%1] make the pipe It failed that [%1] get the folder path to Bitmap Configuration Error Message [%1] Error Code [%2] Configuration error[%1] WSAGetLastError = [%2] It failed that [%1] closes connection with RU [%2] Ack Message Time Out (%1).%n[%2] Program error. Program error. Program error. Program error. Program error. Program error. The Bitmap key was not found in Directory.ini. Program error. The program was faulty or SysConfig.mdb was abnormal. Program error. The connection to the RU was closed or an Check the connection to the RU. error occurred in the connection. There is no operational problem (the button might not normally be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL. Reinstall the system.

Causes

Remedies

Remarks

13012 FFIdConnection Watch 13012 FFIdMenuChange 13012 FFIdRuMainControl 13012 FFIdConnection WatchEx 13012 FFIdRuMain ControlEx 13012 FFInput 13013 FFIdMenuChange 13013 FFIdConnection WatchEx 13013 FFIdRuMain ControlEx 13013 FFInput 13014 FFIdConnection Watch 13014 FFIdMenuChange

It failed that [%1] get the bitmap to Id_PrevPage_U.bmp/Id_PrevPage_ Previous Page D.bmp/Id _PrevPage_X.bmp was not found in the path to an image folder or the image format was illegal. Ack Message Time Out[%1] Ack Message Time Out Message [%1] Error Code [%2] Ack Message Time Out[%1] WSAGetLastError = [%2] [%1] No RU Used

13014 FFIdRuMainControl 13014 FFIdConnection WatchEx 13014 FFIdRuMain ControlEx 13014 FFInput

The connection to the RU was closed or an Check the connection to the RU. error occurred in the connection. The connection to the RU was closed or an Restore the RU connection to normal. error occurred in the connection. The connection to the RU was closed or an Restore the RU connection to normal. error occurred in the connection. Although the FRUP option is selected, the RU connection setting is not found in NetConfig. There are inconsistencies between the option settings and Config settings. Check settings.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-67

Appx MT1-68
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Arbitrary Information Details.

Causes
A message related to a system operation.

Remedies
Nothing particular.

Remarks
%1=Error Code: The code that uniquely identifies an error. %2=Subsystem: The subsystem where an error occurred. %3=Source File: The program file where an error occurred. %4=Spot Code: The location where an error actually occurred (a unique value within the program).

13014 ImportImageFolder AccessCom

13015 FFIdMenuChange

It failed that [%1] get the bitmap to Id_NextPage_U.bmp/Id_NextPage_ Next Page D.bmp/Id _NextPage_X.bmp was not found in the path to an image folder or the image format was illegal. Thread End Error[%1] Thread End Error Message [%1] Error Code [%2] Thread End Error[%1] WSAGetLastError = [%2] [%1] failed in setting DICOM data [%2] Memory Error Message [%1] Error Code [%2] Error[%1] WSAGetLastError = [%2] [%1] failed in the acquisition of DICOM data [%2] RU Host Unknown Error Message [%1] Error Code [%2] RU Host Unknown Error Message [%1] Error Code [%2] The code of the specified group does not exist in [%1] The code of the specified menu does not exist in [%1] RU Error DB Connect Error in [%1] Program error. Program error. Program error. Program error. Program error. Program error. The error is attributable to improper RU setup for the CR-IR 391CL or a faulty program. The error is attributable to improper RU setup for the CR-IR 391CL or a faulty program. Program error. Program error.

There is no operational problem (the button might not normally be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL.

13015 FFIdRuMainControl 13015 FFIdConnection WatchEx 13015 FFIdRuMain ControlEx 13015 FFInput 13016 FFIdConnection WatchEx 13016 FFIdRuMain ControlEx 13016 FFInput 13017 FFIdConnection WatchEx 13017 FFIdRuMain ControlEx 13018 FFInput 13019 FFInput 13020 FFInput

The connection character string was not Reinstall the system. properly registered for the RuErrorDataDB key in Directory.ini or the RU error information database did not exist.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-68

Appx MT1-69
Event Event Source Description
RU Error Data Get Error in [%1] RU Status DB Connection String Get Error in [%1] %1 (%2) : Patient Information Check Error%n Item [%3]%n Error [%4] RU Status DB Connect Error in [%1]

Causes

Remedies

Remarks

13021 FFInput 13022 FFInput 13023 FFIdPatInfoInput

The window number sent from the RU was Ensure that the RU version agrees with the not found in the RU error information RU error information database version. database. The connection character string was not properly registered for the RuStatusDataDB key in Directory.ini. The patient information contained illegal information. The connection character string was not properly registered for the RuStatusDataDB key in Directory.ini or the RU error information database did not exist. Id_LocalSearch_U.bmp/Id_ LocalSearch_D.bmp/Id_LocalSearch_ X.bmp was not found in the path to an image folder or the image format was illegal. The status number sent from the RU was not found in the RU error information database. The patient information database is damaged. Program error. Patient information to be registered Enter correct patient information or repair included illegal information items or patient patient information database. information database was damaged. No matching patient information was found. Control information Program error. Control information Nothing particular. Nothing particular. Reinstall the system. Correct the patient information setup.

13023 FFInput

Reinstall the system.

13024 FFIdPatInfoInput

%1 (%2) : Bitmap Image Get Error%n BMP File [%3] RU Status Data Get Error in [%1] %1 (%2) : Patient Info Get Error%n Error [%3]%n RetCode [%4] %1%n%2%n%3%n%4%n%5%n %6%n%7%0 %1 (%2) : Patient Info Set Error%n Error [%3]%n RetCode [%4] %1 (%2) : Patient Info Not Correspond%n RetCode [%3]%n %1%n%2%n%3%n%4%n%5%n %6%n%7%0 %1%n%2%n%3%n%4%n%5%n %6%n%7%0 %1%n%2%n%3%n%4%n%5%n %6%n%7%0 [%s] %s (%s) : Log Output Directory Get Error

Place Id_LocalSearch_U.bmp, Id_ LocalSearch_D.bmp, and Id_ LocalSearch_X.bmp in the path to the folder in which images are positioned. Ensure that the RU version agrees with the RU status information database version. Repair the patient information database.

13024 FFInput 13025 FFIdPatInfoInput

13025 FFInput 13026 FFIdPatInfoInput

13027 FFIdPatInfoInput 13027 FFInput 13028 FFInput 13030 FFInput 13031 FFInput

The system setup database was damaged. Reinstall the system.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-69

Appx MT1-70
Event Event Source Description
[%s] %s (%s) : LR button cannot be concave set [%s] %s (%s) : TB button cannot be concave set [%s] %s (%s) : TBLR button cannot be concave set [%s] %s (%s) : rotation button cannot be concave set [%s] %s (%s) : Message Table Name Get Error [%s] %s (%s) : StrDB Connection String Get Error [%s] %s (%s) : StrDB Connect Error

Causes
The range was changed by the Service Utility. The range was changed by the Service Utility. The range was changed by the Service Utility. The range was changed by the Service Utility.

Remedies
Nothing particular. Nothing particular. Nothing particular. Nothing particular.

Remarks

13033 FFInput 13034 FFInput 13035 FFInput 13036 FFInput 13037 FFInput 13038 FFInput 13039 FFInput 13040 FFInput 13041 FFInput 13052 FFInput 13053 FFInput 13054 FFInput 13055 FFInput 13056 FFInput 13057 FFInput 13058 FFInput 13059 FFInput 13060 FFInput

The MsgTableName key was not found in Reinstall the system. the system setup database. The LangStrDB key was not found in Directory.ini. Reinstall the system.

Reinstall the system. The connection character string was not properly registered for the LangStrDB key in Directory.ini. Reinstall the system. Reinstall the system. Reinstall the system.

[%s] %s (%s) : SysDB Connection The SysConfigDB key was not found in String Get Error Directory.ini. [%s] %s (%s) : SysDB Connect Error [%s] %s (%s) : Failed MenuDB Initialize [%s] %s (%s) : Menu Data in ImageDB Get Error [%s] %s (%s) : Menu Parameter Data in ImageDB Get Error [%s] %s (%s) : Failed MenuDB Termination The connection character string was not properly registered for the SysConfigDB key in Directory.ini. The menu database access initialization process was not successfully performed.

The menu information was not successfully Reinstall the system. acquired from the menu database. The menu parameter information was not successfully acquired from the menu database. The menu database access termination process was not successfully performed. Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

[%s] %s (%s) : NetDB Connection The NetConfigDB key was not found in Character String Get Error Directory.ini. [%s] %s (%s) : Failed NetDB Connection [%s] %s (%s) : NetDB Data Get Error The connection character string was not properly registered for the NetConfigDB key in Directory.ini. The network setup database was damaged.

[%s] %s (%s) : Failed Create New An attempt to create new DICOM data DICOM Data failed. [%s] %s (%s) : DICOM Data Get Error The DICOM data was not successfully acquired.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-70

Appx MT1-71
Event Event Source Description
[%s] %s (%s) : DICOM Data Set Error [%s] %s (%s) : DICOM Data Delete Error

Causes
An attempt to set up DICOM data failed. The DICOM data was not successfully deleted.

Remedies
Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Reinstall the system. Reinstall the system.

Remarks

13061 FFInput 13062 FFInput 13063 FFInput 13064 FFInput 13065 FFInput 13066 FFInput 13067 FFInput 13068 FFInput 13069 FFInput

[%s] %s (%s) : DICOM Data Load The DICOM data was not successfully Error loaded. [%s] %s (%s) : DICOM Data Save The DICOM data was not successfully Error saved. [%s] %s (%s) : DICOM Data Free Error [%s] %s (%s) : Failed in Padding Acquisition[Id#] [%s] %s (%s) : Failed in Padding Acquisition[Exam#] [%s] %s (%s) : Failed in Format Acquisition[Date Of Birth] [%s] %s (%s) : Cannot Access Data Base[Depart.mdb] The DICOM data was not successfully opened. The IdPadding key was not found in the system setup database. The ExaminationNoPadding key was not found in the system setup database.

The DateFormat key was not found in the Reinstall the system. system setup database. The requesting department database was not found in the path indicated by the connection character string. The requesting department table did not exist. The FieldDepartList key was not found in the system setup database. Program error. The DepartDB key was not found in Directory.ini. The technicians database was not found in the pass indicated by the connection character string or the technicians table did not exist. The FieldParamedicList key was not found in the system setup database. Program error. Reinstall the system. Reinstall the system. Reinstall the system.

13070 FFInput 13071 FFInput 13072 FFInput 13073 FFInput

[%s] %s (%s) : Displayed Item Is Not Understood[Depart List] [%s] %s (%s) : Failed in Acquisition[Depart] [%s] %s (%s) : Failed in Connected String Acquisition[Depart] [%s] %s (%s) : Cannot Access Data Base[Paramedic.mdb] [%s] %s (%s) : Displayed Item Is Not Understood[Paramedic List] [%s] %s (%s) : Failed in Acquisition[Paramedic]

Reinstall the system.

13074 FFInput 13075 FFInput

Reinstall the system.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-71

Appx MT1-72
Event Event Source Description
[%s] %s (%s) : Failed in Connected String Acquisition[Paramedic] [%s] %s (%s) : Failed in Window Size Acquisition [%s] %s (%s) : Failed in ExposureList Erase [%s] %s (%s) : Config Directory Character String Get Error [%s] %s (%s) : StrDB Message String Get Error [%s] %s (%s) : IP-Address (RU) Get Error [%s] %s (%s) : Initialize Timeout <InImg> [%s] %s (%s) : Terminate Error <InImg>

Causes
The ParamedicDB key was not found in Directory.ini. The registry was damaged. The ExposureListEraset key was not found in the system setup database. The Confdig key was not found in Directory.ini. The image database was damaged. The network setup database was damaged. The system was unstable. The system was unstable.

Remedies
Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Restart. Restart. Restart. Restart. Restart. Restart. Reinstall the system. Reinstall the system. Reinstall the system.

Remarks

13076 FFInput 13077 FFInput 13078 FFInput 13079 FFInput 13081 FFInput 13082 FFInput 13083 FFInput 13084 FFInput 13085 FFInput 13086 FFInput 13087 FFInput 13088 FFInput 13089 FFInput 13090 FFIdDepartSelect 13090 FFIdParamedic Select 13090 FFInput 13090 FFIdIndividualSelect 13091 FFIdDepartSelect

[%s] %s (%s) : Terminate Timeout The system was unstable. <InImg> [%s] %s (%s) : Input Method Error The system was unstable. <InImg> [%s] %s (%s) : Original Image Input Failure <InImg> [%s] %s (%s) : Image Processing Trouble <InImg> [%s] %s (%s) : Menu Read Error <IdExposureList> The system was unstable. The system was unstable. The image database or information file is damaged.

%1 (%2) : Invalid Depart Code%n Directory.ini was damaged. Code [%3] %1 (%2) : Invalid Paramedic Code%n Code [%3] Directory.ini was damaged.

[%s] %s (%s) : Examination Program error. Terminate Error <IdExposureList> %1 (%2) : Invalid Depart/ Paramedic Code%n Code [%3] %1 (%2) : Invalid Depart Name (SBCS)%n Name (SBCS) [%3] Directory.ini was damaged. The database was damaged. Repair Directory.ini. Reinstall the system.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-72

Appx MT1-73
Event Event Source Description
%1 (%2) : Invalid Paramedic Name (SBCS)%n Name (SBCS) [%3]

Causes
The database was damaged.

Remedies
Reinstall the system.

Remarks

13091 FFIdParamedic Select 13091 FFInput 13091 FFIdIndividualSelect 13092 FFIdDepartSelect 13092 FFIdParamedic Select 13092 FFInput 13092 FFIdIndividualSelect 13093 FFInput 13094 FFInput 13095 FFInput 13096 FFInput 13097 FFInput 13098 FFIdPatInfoInput

[%s] %s (%s) : Input Method Error Program error. <IdExposureList> %1 (%2) : Invalid Depart/ Paramedic Name (SBCS)%n Name (SBCS) [%3] %1 (%2) : Invalid Depart Name (DBCS)%n Name (DBCS) [%3] %1 (%2) : Invalid Paramedic Name (DBCS)%n Name (DBCS) [%3] [%s] %s (%s) : Input End Method Error <IdExposureList> %1 (%2) : Invalid Depart/ Paramedic Name (DBCS)%n Name (DBCS) [%3] [%s] %s (%s) : Priority Change Method Error <IdExposureList> [%s] %s (%s) : Message Send Error <IpcInfCom> [%s] %s (%s) : State Change Method Error <RU> The database was damaged. Program error. Program error. Program error. Program error. Program error. The system was unstable. Program error. Check the RU status. Restart. Repair the database.

[%s] %s (%s) : Request Command The RU side might be faulty (a command Not Executed <RU> was not executed although it was requested). [%s] %s (%s) : State Info Get Error <RU> %1 (%2) : %n [%3]%n %4%n %5 [%s] %s (%s) : Reconnect Error <RU> FF32lib A WIN32 system library error occurred. [%1]%n%2 FFNetDB A WIN32 system library error occurred. [%1]%n%2 Program error. A general-purpose message related to patient information input (for error indication/information display). The line was abnormal. An error occurred when calling up the WIN32 API. An error occurred when calling up the WIN32 API.

If an error is encountered, a custom message box appears. Follow the instructions set forth in the custom message box.

13098 FFInput 13098 FF32LIB 13098 FFNetDB

Restart the server computer. Restart the server computer.

[%1, %2, %3, %4, %5]: Detailed information [%1, %2, %3, %4, %5]: Detailed information

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-73

Appx MT1-74
Event Event Source Description
Unknown error has occurred [%1] Program error. (%2) [%s] %s (%s) : Disconnect Error <RU> FF32lib An unknown error occurred. [%1]%n%2 FFNetDB An unknown error occurred. [%1]%n%2 [%s] %s (%s) : Failed in Display Group Acquisition[Free] [%s] %s (%s) : Failed in Display Menu Acquisition[Initialize] [%s] %s (%s) : Failed in Display Menu Acquisition[Record] [%s] %s (%s) : Failed in Display Menu Acquisition [%s] %s (%s) : Failed in Display Menu Acquisition[Free] [%s] %s (%s) : Failed in Display Menu Acquisition[Endding ] The line was abnormal. An exception error occurred. An exception error occurred. Program error. The DisplayDataDB key was not found in Reinstall the system. Directory.ini. The menu database is damaged. Program error. Program error. Program error. Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Restart the server computer. Restart the server computer. [%1, %2, %3, %4, %5]: Detailed information [%1, %2, %3, %4, %5]: Detailed information

Causes

Remedies

Remarks

13099 FFIdMenuItem 13099 FFInput 13099 FF32LIB 13099 FFNetDB 13102 FFInput 13103 FFInput 13104 FFInput 13105 FFInput 13106 FFInput 13107 FFInput 13108 FFInput 13109 FFInput 13110 13111 13112 13113 13114 13115 13116 FFInput FFInput FFInput FFInput FFInput FFInput FFInput

[%s] %s (%s) : Failed in Exposure The menu database is damaged. Menu Acquisition [%s] %s (%s) : Next Set Number Data Get Error [%s] %s (%s) : Next Set Number Data Set Error [%s] %s (%s) : System ID Data Get Error [%s] %s (%s) : Auto Distribution Data Get Error [%s] %s (%s) : Enable Selector Data Get Error [%s] %s (%s) : Auto Menu Select Data Get Error [%s] %s (%s) : Next Set Number Min Data Get Error [%s] %s (%s) : Next Set Number Max Data Get Error The registry was damaged. The registry was damaged.

The system setup database was damaged. Reinstall the system. The system setup database was damaged. Reinstall the system. The system setup database was damaged. Reinstall the system. The system setup database was damaged. Reinstall the system. The system setup database was damaged. Reinstall the system. The system setup database was damaged. Reinstall the system.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-74

Appx MT1-75
Event
13117 13118 13119

Event Source
FFInput FFInput FFInput

Description
[%s] %s (%s) : Image UID Issue Error [%s] %s (%s) : Series Instance UID Issue Error [%s] %s (%s) : Failed in Auto Distribution [%s] %s (%s) : Failed in Getting ID-Online Port# Program error. Program error. Program error.

Causes

Remedies

Remarks

13120 FFInput 13121 FFInput 13122 FFInput 13123 FFInput 13124 FFInput 13125 FFInput 13126 FFInput 13127 FFInput 13128 FFInput 13129 FCRWeb

The database was not found or the associated key did not exist.

Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system.

[%s] %s (%s) : Failed in ID-Online The database was not found or the Device Name associated key did not exist. [%s] %s (%s) : RU Status DB Connection String Get Error Directory.ini was damaged.

[%s] %s (%s) : Failed in selectable The SelectableDirection key was not direction found in the system setup database or its value was incorrect. [%s] %s (%s) : Failed in Selectable Image Format Acquisition [%s] %s (%s) : FilmMarkDB Connection String Get Error [%s] %s (%s) : FilmMarkDB Connect Error [%s] %s (%s) : FilmMarkDB Get Error [Film Mark Information]

The SelectableFormat key was not found Reinstall the system. in the system setup database or its value was incorrect. The FilmMarkDB key was not found in Directory.ini. The connection character string was not properly registered for the FilmMarkDB key in Directory.ini. Program error. Reinstall the system. Reinstall the system.

[%s] %s (%s) : Failed in Limit Film The LimitFilmCopy key was not found in Reinstall the system. Copy Acquisition the system setup database or its value was incorrect. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCan not delete RU-controlresult from database. RU-controlresult already deleted by other user/process. The RU operation record was not successfully deleted. An internal system error occurred. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

13129 FFInput 13130 FFInput

[%s] %s (%s) : Thumbnail Creating Trouble <InImg>

Program error.

[%s] %s (%s) : ID Change Method Program error. Error <InImg>

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-75

Appx MT1-76
Event Event Source Description Causes Remedies
Reinstall the system. Reinstall the system.

Remarks

13131 FFInput 13132 FFInput 13133 FFInput 13134 FFInput 13135 FFInput

[%s] %s (%s) : Failed in The SelectableEdrMode key was not Selectable EDR Mode Acquisition found in the system setup database or its value was incorrect. [%s] %s (%s) : Failed in Selectable Function Acquisition The SelectableFunction key was not found in the system setup database or its value was incorrect.

[%s] %s (%s) : ID Change Method Program error. Error <QABase> [%s] %s (%s) : Failed in The SelectableFilingMode key was not Selectable EDR Mode Acquisition found in the system setup database or its value was incorrect. [%s] %s (%s) : NetDB Data Get Error [%s] %s (%s) : Failed in Enable DistributionCode Acquisition [%s] %s (%s) : Failed in Enable FileString Acquisition [%s] %s (%s) : Failed in Enable Function Acquisition [%s] %s (%s) : Terminate Error <IdExposureList> [%s] %s (%s) : Terminate Error <IdHome> [%s] %s (%s) : List Update Error <IdHome> An attempt to acquire a connection character string from the network setup database failed, or the network setup database was not found. The EnableDistributionCode key was not found in the system setup database or its value was incorrect. The EnableFileString key was not found in the system setup database or its value was incorrect. Reinstall the system. Reinstall the system.

13136 FFInput 13137 FFInput 13138 FFInput 13139 FFInput 13140 FFInput 13141 FFInput 13142 FFInput 13143 FFInput 13144 FFInput 13145 FFInput 13146 FFInput 13147 FFInput

Reinstall the system. Reinstall the system.

The EnableFunction key was not found in Reinstall the system. the system setup database or its value was incorrect. Program error. Program error. Program error.

[%s] %s (%s) : Study List Initialize Program error. Error [Registered] [%s] %s (%s) : Study List Initialize Program error. Error [QaWaiting] [%s] %s (%s) : Study List Initialize Program error. Error [OutputWaiting] [%s] %s (%s) : Study List Initialize Program error. Error [Outputted] [%s] %s (%s) : Study List Initialize Program error. Error [All] [%s] %s (%s) : Study List Initialize Program error. Error [Today]

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-76

Appx MT1-77
Event Event Source Description
[%s] %s (%s) : Study List Update Error [Registered] [%s] %s (%s) : Study List Update Error [QaWaiting] [%s] %s (%s) : Study List Update Error [OutputWaiting] [%s] %s (%s) : Study List Update Error [Outputted] [%s] %s (%s) : Study List Update Error [All] [%s] %s (%s) : Study List Update Error [Today] [%s] %s (%s) : Study Instance UID Get Error <IdHome> [%s] %s (%s) : Study Instance UID Get Error IdHome> [%s] %s (%s) : QA Start Method Error <QABase> [%s] %s (%s) : Finish Mode Get Error [%s] %s (%s) : RU Error DB Connection String Get Error Program error. Program error. Program error. Program error. Program error. Program error. Program error. Program error. Program error. The system setup database was damaged. Reinstall the system. The RuErrorDataDB key was not found in Reinstall the system. Directory.ini.

Causes

Remedies

Remarks

13148 FFInput 13149 FFInput 13150 FFInput 13151 FFInput 13152 FFInput 13153 FFInput 13154 FFInput 13155 FFInput 13156 FFInput 13157 FFInput 13158 FFInput 13159 FFInput 13160 FFInput 13161 FFInput 13162 FFInput 13163 FFInput 13164 FFInput 13165 FFInput 13166 FFInput

[%s] %s (%s) : RU Error DB Table The MsgTableName key was not found in Reinstall the system. Name Get Error the system setup database. [%s] %s (%s) : Call Error [RU Error CUSTOM MESSAGE BOX] [%s] %s (%s) : Failed Display Thumbnail Image [%s] %s (%s) : Ip Size Unit (Inch/ Metric) Get Error [%s] %s (%s) : RU Utility Start Method Error <IdStatusBase> [%s] %s (%s) : Image Proc End Method Error <IdExposureList> [%s] %s (%s) : Image Size Code Specify Error [%s] %s (%s) : Pantomo Setting Get Error The specified ID was not registered in RuErrorDataDB or the custom message box was not successfully called. The program was faulty or the image file was damaged. Reinstall the system. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

The system setup database was damaged. Reinstall the system. Program error. Program error. RU-dependent symptom. Check the RU status.

The system setup database was damaged. Repair the system setup database.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-77

Appx MT1-78
Event Event Source Description
[%s] %s (%s) : RU Error Info Get Error

Causes
The RU error database was damaged.

Remedies
Reinstall the RU software. Reinstall the RU software.

Remarks

13167 FFInput 13168 FFInput 13169 FFInput 13170 FFInput 13171 FFInput 13172 FFInput 13173 FFInput 13174 FFInput 13175 FFInput 13176 FFInput 13177 FFInput 13178 FFInput 13179 FFInput 13180 FFInput 13181 FFInput 13182 FFInput 13183 FFInput 13187 FFInput 13188 FFInput

[%s] %s (%s) : RU Status Info Get The RU status information database was Error damaged. [%s] %s (%s) : Thumbnail End Method Error <IdExposureList> [%s] %s (%s) : Study List Setting Save Error [Registered] [%s] %s (%s) : Study List Setting Save Error [QaWaiting] [%s] %s (%s) : Study List Setting Save Error [OutputWaiting] [%s] %s (%s) : Study List Setting Save Error [Outputted] [%s] %s (%s) : Study List Setting Save Error [All] [%s] %s (%s) : Study List Setting Save Error [Today] [%s] %s (%s) : Study List Customize Error [%s] %s (%s) : Default Menu Code Get Error [%s] %s (%s) : Next Multi Frame Pair Code Data Get Error [%s] %s (%s) : Next Multi Frame Pair Code Data Set Error [%s] %s (%s) : Series Generation Type Data Get Error [%s] %s (%s) : Multi Frame UID Information Get Error [%s] %s (%s) : Failed in Getting XCON Port# [%s] %s (%s) : Failed in XCON Device Name [%s] %s (%s) : Font Name Get Error [%s] %s (%s) : Font Size Get Error Program error. Program error. Program error. Program error. Program error. Program error. Program error. Program error.

The system setup database was damaged. Reinstall the system. The registry was damaged. The registry was damaged. Reinstall the system. Reinstall the system.

The system setup database was damaged. Reinstall the system. The system setup database was damaged. Reinstall the system. The database was not found or the associated key did not exist. The database was not found or the associated key did not exist. The Font key was not found in the registry. Reinstall the system. Reinstall the system. There is no operational problem (garbled characters may be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL.

The FontSizeSS/FontSizeS/FontSizeM There is no operational problem (garbled /FontSizeL/FontSizeLL key was not characters may be displayed). If you feel found in the registry. uncomfortable, reinstall the CR-IR 391CL.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-78

Appx MT1-79
Event Event Source Description
[%s] %s (%s) : Failed in Caption Acquisition[Id#] [%s] %s (%s) : Failed in Caption Acquisition[Exam#] [%s] %s (%s) : Failed in Caption Acquisition[SBCS Patient Name] [%s] %s (%s) : Failed in Caption Acquisition[DBCS Patient Name] [%s] %s (%s) : Failed in Caption Acquisition[Sex] [%s] %s (%s) : Failed in Caption Acquisition[Sex M] [%s] %s (%s) : Failed in Caption Acquisition[Sex F] [%s] %s (%s) : Failed in Caption Acquisition[Sex O] [%s] %s (%s) : Failed in Caption Acquisition[Date Of Birth]

Causes

Remedies
Reinstall the system.

Remarks

13189 FFInput 13190 FFInput 13191 FFInput 13192 FFInput 13193 FFInput 13194 FFInput 13195 FFInput 13196 FFInput 13197 FFInput 13198 FFInput 13199 FFInput 13200 FFInput 13201 FFInput 13202 FFInput 13203 FFInput

[%s] %s (%s) : Multibyte Flag Get The Multibyte key was not found in the Error registry.

The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30700 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30701 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30702 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30704 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30704 was not registered in the character string database. Reinstall the system. The LangStrDB key was not found in Directory.ini or the ID 30705 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30706 was not registered in the character string database. Reinstall the system. The LangStrDB key was not found in Directory.ini or the ID 30707 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 0708 was not registered in the character string database. Reinstall the system. Reinstall the system.

[%s] %s (%s) : Failed in Limitation The IdLength key was not found in the No Acquisition[Id#] system setup database. [%s] %s (%s) : Failed in Limitation The ExaminationNoLength key was not No Acquisition[Exam#] found in the system setup database. [%s] %s (%s) : Failed in Caption Acquisition[Depart] [%s] %s (%s) : Failed in Caption Acquisition[Paramedic]

The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30800 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30800 was not registered in the character string database. Reinstall the system.

[%s] %s (%s) : Image Folder Path The Bitmap key was not found in Get Error Directory.ini.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-79

Appx MT1-80
Event Event Source Description
[%s] %s (%s) : [Clear]Button Image Get Error [%s] %s (%s) : [Ok]Button Image Get Error [%s] %s (%s) : [Cancel]Button Image Get Error

Causes
Id_Clear_U.bmp/Id_Clear_D.bmp/Id_ Clear_ X.bmp was not found in the path to an image folder or the image format was illegal. Id_Ok_U.bmp/Id_Ok_D.bmp/Id_Ok_ X.bmp was not found in the path to an image folder or the image format was illegal. Id_Cancel_U.bmp/Id_Cancel_ D.bmp/Id_Cancel_X.bmp was not found in the path to an image folder or the image format was illegal.

Remedies
There is no operational problem (the button might not normally be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL. There is no operational problem (the button might not normally be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL. There is no operational problem (the button might not normally be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL. There is no operational problem (the button might not normally be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL. There is no operational problem (the button might not normally be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL. There is no operational problem (the button might not normally be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL. There is no operational problem (the button might not normally be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL. Check the line. Check the line. Check the line. Check the line.

Remarks

13204 FFInput

13205 FFInput

13206 FFInput

13207 FFInput

[%s] %s (%s) : [Plus]Button Image Id_Plus_U.bmp/Id_Plus_D.bmp/Id_ Get Error Plus_X.bmp was not found in the path to an image folder or the image format was illegal. [%s] %s (%s) : [Minus]Button Image Get Error Id_Minus_U.bmp/Id_Minus_D.bmp/Id_ Minus_ X.bmp was not found in the path to an image folder or the image format was illegal.

13208 FFInput

13209 FFInput

[%s] %s (%s) : [Next Page]Button Id_NextPage_U.bmp/Id_NextPage_ Image Get Error D.bmp/Id _NextPage_X.bmp was not found in the path to an image folder or the image format was illegal. [%s] %s (%s) : [Previous Page] Button Image Get Error [%s] %s (%s) : RU Watch Connection Disconnected [%s] %s (%s) : No ACK Returned in RU Watch Connection [%s] %s (%s) : RU Control Connection Disconnected [%s] %s (%s) : No ACK Returned in RU Control Connection [%s] %s (%s) : Model Code Get Error <RU> Id_PrevPage_U.bmp/Id_PrevPage_ D.bmp/Id _PrevPage_X.bmp was not found in the path to an image folder or the image format was illegal. The line was abnormal. The line was abnormal. The line was abnormal. The line was abnormal. Program error.

13210 FFInput

13211

FFInput

13212 FFInput 13213 FFInput 13214 FFInput 13215 FFInput 13216 FFInput 13217 FFInput

[%s] %s (%s) : FRUP Version Get Program error. Error <RU> [%s] %s (%s) : Failed in Caption Acquisition[Complete] The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30202 was not registered in the character string database.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-80

Appx MT1-81
Event Event Source Description
[%s] %s (%s) : Failed in Caption Acquisition[QA Unfinished] [%s] %s (%s) : Failed in Caption Acquisition[Interrupt] [%s] %s (%s) : Failed in Caption Acquisition[Cancel] [%s] %s (%s) : Failed in Caption Acquisition[New Study] [%s] %s (%s) : Failed in Caption Acquisition[Registered] [%s] %s (%s) : Failed in Caption Acquisition[QA Waiting] [%s] %s (%s) : Failed in Caption Acquisition[Output Waiting] [%s] %s (%s) : Failed in Caption Acquisition[Outputted] [%s] %s (%s) : Failed in Caption Acquisition[All] [%s] %s (%s) : Failed in Caption Acquisition[Today] [%s] %s (%s) : Failed in Image Acquisition[System] [%s] %s (%s) : Failed in Caption Acquisition[StudyReseve] [%s] %s (%s) : Failed in Caption Acquisition[StudyStart] [%s] %s (%s) : An Illegal Film Mark Character Was Detected [%s] %s (%s) : Failed in Caption Acquisition[FIX]

Causes

Remedies

Remarks

13218 FFInput 13219 FFInput 13220 FFInput 13221 FFInput 13222 FFInput 13223 FFInput 13224 FFInput 13225 FFInput 13226 FFInput 13227 FFInput 13228 FFInput 13229 FFInput 13230 FFInput 13270 FFInput 13271 FFInput

The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30201 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30200 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30203 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30500 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30501 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30502 was not registered in the character string database. Reinstall the system. The LangStrDB key was not found in Directory.ini or the ID 30503 was not registered in the character string database. Reinstall the system. The LangStrDB key was not found in Directory.ini or the ID 30504 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30505 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30506 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30507 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30600 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 30601 was not registered in the character string database. The film mark database is damaged. Reinstall the system.

The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 33502 was not registered in the character string database.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-81

Appx MT1-82
Event Event Source Description
[%s] %s (%s) : Failed in Caption Acquisition[Skfix] [%s] %s (%s) : Failed in Caption Acquisition[SEMI-X] [%s] %s (%s) : Failed in Caption Acquisition[DensityAverage] [%s] %s (%s) : [Utility]Button Image Get Error [%s] %s (%s) : Failed in Caption Acquisition[Alarm Stop] [%s] %s (%s) : Failed in Caption Acquisition[Exit] [%s] %s (%s) : Failed in Caption Acquisition[User Utility] [%s] %s (%s) : Failed in Caption Acquisition[List Setting] [%s] %s (%s) : Failed in Caption Acquisition[Version] [%s] %s (%s) : Failed in Caption Acquisition[CANCEL] [%s] %s (%s) : [Clear]Button Image Get Error [%s] %s (%s) : [Clear]Button ToolTipText Get Error [%s] %s (%s) : Failed in Caption Acquisition[CANCEL] [%s] %s (%s) : Failed in Caption Acquisition[DUST] [%s] %s (%s) : Tooltip Text Get Error [%s] %s (%s) : Failed in Caption Acquisition[TitleBar] [%s] %s (%s) : Failed in Caption Acquisition[Option]

Causes

Remedies

Remarks

13272 FFInput 13273 FFInput 13274 FFInput 13275 FFInput

The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 33503 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 33504 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 33505 was not registered in the character string database. Id_Utility_U.bmp/Id_Utility_D.bmp/Id_ Utility_X.bmp was not found in the path to an image folder or the image format was illegal. There is no operational problem (the button might not normally be displayed). If you feel uncomfortable, reinstall the CR-IR 391CL.

13276 FFInput 13277 FFInput 13278 FFInput 13279 FFInput 13280 FFInput 13281 FFInput 13282 FFInput 13283 FFInput 13284 FFInput 13285 FFInput 13286 FFInput 13287 FFInput 13288 FFInput

The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 32700 was not registered in the character string database. The image database was damaged. The image database was damaged. The image database was damaged. The image database was damaged. The image database was damaged. The bmp file path/bmp file was abnormal. The image database was damaged. Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system.

The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 35000 was not registered in the character string database. The LangStrDB key was not found in Reinstall the system. Directory.ini or the ID 35001 was not registered in the character string database. The image database was damaged. The image database was damaged. The image database was damaged. Reinstall the system. Reinstall the system. Reinstall the system.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-82

Appx MT1-83
Event Event Source Description
[%s] %s (%s) : Version Info Get Error [%s] %s (%s) : Option List Get Error [%s] %s (%s) : Image Data Connection Disconnected [%s] %s (%s) : Multiple Study Cannot Be Executed [%s] %s (%s) : StudyList Has Not Been Selected [%s] %s (%s) : Control Initialize Error [%s] %s (%s) : Patient Info Read Error IdHome> [%s] %s (%s) : Failed in Patient Information %1 (%2) : Database Data Get Error%n Database [%3]%n Table [%4]%n Key [%5] %1 (%2) : Database Data Get Error%n Database [%3]%n Table [%4]%n Key [%5] %1 (%2) : Database Data Get Error%n Database [%3]%n Table [%4]%n Key [%5] %1 (%2) : Database Data Get Error%n Database [%3]%n Table [%4]%n Key [%5] %1 (%2) : Database Data Get Error%n Database [%3]%n Table [%4]%n Key [%5]

Causes
The registry was damaged. The registry was damaged. The line was abnormal. Program error. Program error. Program error. Program error.

Remedies
Reinstall the system. Reinstall the system. Check the line.

Remarks

13289 FFInput 13290 FFInput 13304 FFInput 13305 FFInput 13306 FFInput 13307 FFInput 13308 FFInput 13309 FFInput 13345 FFIdDepartSelect

The patient information contained an illegal Ensure that the patient information does character string. not contain any illegal character string. The database was damaged. Reinstall the system.

13345 FFIdParamedic Select

The database was damaged.

Reinstall the system.

13345 FFIdPatInfoInput

The database was damaged.

Reinstall the system.

13345 FFInput

The database was damaged.

Reinstall the system.

13345 FFIdIndividualSelect

The database was damaged.

Repair the database.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-83

Appx MT1-84
Event Event Source Description
%1 (%2) : Patient Information Check Error%n Item [%3]%n Error [%4] %1 (%2) : Caption Get Error%n CaptionId [%3] %1 (%2) : Registry Data Get Error%n Value [%3] %1 (%2) : Registry Data Get Error%n Value [%3] %1 (%2) : Registry Data Get Error%n Value [%3] %1 (%2) : Registry Data Get Error%n Value [%3] %1 (%2) : Registry Data Get Error%n Value [%3] %1 (%2) : Registry Data Get Error%n Value [%3] %1 (%2) : INI File Data Get Error%n Key [%3] %1 (%2) : INI File Data Get Error%n Key [%3] %1 (%2) : INI File Data Get Error%n Key [%3] %1 (%2) : INI File Data Get Error%n Key [%3] %1 (%2) : INI File Data Get Error%n Key [%3] %1 (%2) : INI File Data Get Error%n Key [%3]

Causes
The patient information contained illegal information. The image database was damaged. The registry was damaged. The registry was damaged. The registry was damaged. The registry was damaged. The registry was damaged. The registry was damaged. Directory.ini was damaged. Directory.ini was damaged. Directory.ini was damaged. Directory.ini was damaged. Directory.ini was damaged. Directory.ini was damaged.

Remedies
Correct the patient information setup.

Remarks

13346 FFInput

13347 FFInput 13348 FFIdDepartSelect 13348 FFIdMenuChange 13348 FFIdParamedic Select 13348 FFIdPatInfoInput 13348 FFInput 13348 FFIdIndividualSelect 13349 FFIdDepartSelect 13349 FFIdMenuChange 13349 FFIdParamedic Select 13349 FFIdPatInfoInput 13349 FFInput 13349 FFIdIndividualSelect

Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system.

Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Repair Directory.ini.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-84

Appx MT1-85
Event Event Source Description
%1 (%2) : Bitmap Image Get Error%n BMP File [%3] %1 (%2) : Bitmap Image Get Error%n BMP File [%3] %1 (%2) : Search Number Check Error%nError [%3] %1 (%2) : Dicom MWM & PPS Option Not Install %1 (%2) : Dicom MWM Option Not Install %1 (%2) : Formality Function Steps Error %1 (%2) : Exception Error %3 %1 (%2) : Control Initialize Error [%3] %1 (%2) : Get Control Instance Error [%3] %1 (%2) : Call Control Method [%3] %1 (%2) : Set Control Property [%3] %1 (%2) : Dicom Control Response Error [%3] %1 (%2) : Database Close Error%n Database [%3]%n %1 (%2) : Not Entry Host Name %1 (%2) : DDO File Not Found %1 (%2) : Memory Allocate Error [%3] %1 (%2) : Create Instance UID Error [%3] %1 (%2) : Get RecordSet Error [%3] %1 (%2) : RecordSet Not Found %1 (%2) : Copy VR Error The DICOM MWM & PPS option was not installed. Install the DICOM MWM & PPS option.

Causes
The bmp file path/bmp file was abnormal. The bmp file path/bmp file was abnormal.

Remedies
Reinstall the system. Reinstall the system.

Remarks

13350 FFIdMenuChange 13350 FFInput 13351 FFInput 13352 FFInput 13353 FFInput 13354 FFInput 13355 FFInput 13356 FFInput 13357 FFInput 13358 FFInput 13359 FFInput 13360 FFInput 13361 FFInput 13362 FFInput 13363 FFInput 13364 FFInput 13365 FFInput 13366 FFInput 13367 FFInput 13368 FFInput

The DICOM MWM option was not installed. Install the DICOM MWM option. Program error. Program error. Program error. Program error. Program error. Program error. Program error. Program error. The host name of the local equipment was With the Service Utility, register the host not successfully acquired. information about the PPS local equipment. Program error. Program error. Program error. Program error. Program error. Program error.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-85

Appx MT1-86
Event Event Source Description
%1 (%2) : PPS Instance UID Issue Error %1 (%2) : PPS Request Failure [IN PROGRESS] %1 (%2) : PPS Request Failure [COMPLETED] %1 (%2) : PPS Request Failure [DISCONTINUED] %1 (%2) : Study List Refresh Exception%nError [%3] %1 (%2) : Failed in terminating process.%n Component Name [%3] %1 (%2) : The command of OnlineTypeB was received%n [Setting OnlineTypeA.] %1 (%2) : The command of OnlineTypeA was received%n [Setting OnlineTypeB.] %1 (%2) : Failed in data reception%n[Online Time Out] Program error. The equipment connection was faulty or the remote equipment power was OFF. The equipment connection was faulty or the remote equipment power was OFF. The equipment connection was faulty or the remote equipment power was OFF. An unknown error occurred. Program error. Program error. Program error. The serial cable was cut, or the connected device did not respond. Retry. Retry. Retry. Retry.

Causes

Remedies

Remarks

13369 FFInput 13370 FFInput 13371 FFInput 13372 FFInput 13382 FFInput 13383 FFInput 13384 FFInput 13385 FFInput 13386 FFInput 13387 FFInput 13388 FFInput 13389 FFIdDepartSelect 13389 FFIdParamedic Select 13389 FFIdPatInfoInput 13389 FFInput 13389 FFIdIndividualSelect 13390 FFInput

%1 (%2) : Failed in data reception Program error. : (%3)%n[Online NG] %1 (%2) : Failed in event reception. %1 (%2) : Database Connection Error%n Database [%3]%n %1 (%2) : Database Connection Error%n Database [%3]%n %1 (%2) : Database Connection Error%n Database [%3]%n %1 (%2) : Database Connection Error%n Database [%3]%n %1 (%2) : Database Connection Error%n Database [%3]%n %1 (%2) : Depart Info Set Error%n Program error. The database was damaged. The database was damaged. The database was damaged. The database was damaged. The database was damaged. Program error. Reinstall the system. Reinstall the system. Reinstall the system. Reinstall the system. Repair the database.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-86

Appx MT1-87
Event Event Source Description
%1 (%2) : Paramedic Info Set Error%n %1 (%2) : Study List Initialize Error [Worklist] Program error. Program error.

Causes

Remedies

Remarks

13391 FFInput 13393 FFInput 13394 FFInput 13395 FFInput 13396 FFInput 13397 FFInput 13399 FFInput 13400 FCRWeb

%1 (%2) : Study List Update Error Program error. [Worklist] %1 (%2) : Study List Setting Save Program error. Error [Worklist] %1 (%2) : Failed in setting the Program error. connecting status to the RIS (%3) %1 (%2) : Study List Select Error [Worklist] Program error.

%1 (%2) : Thread Create Error%n Program error. Error Code [%3] ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe order was preserved. The sequence was stored. Nothing particular. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

13400 FFInput

%1 (%2) : Process Create Error%n ProcessName [%3]%n Error Code [%4]

Program error.

13401 FFInput 13402 FFInput 13403 FFInput 13404 FFInput 13405 FFInput 13406 FFInput 13407 FFInput 13408 FFInput

%1 (%2) : Shared Memory Create Program error. Error%n Error Code [%3] %1 (%2) : Failed Create New IDT4 Data %1 (%2) : IDT4 Data Get Error [%3] %1 (%2) : IDT4 Data Set Error [%3] %1 (%2) : IDT4 Data Load Error %1 (%2) : IDT4 Data Convert Error [%3] %1 (%2) : Invalid Value Program error. Program error. Program error. Program error. Program error. Program error.

%1 (%2) : Memory Free Error [%3] Program error.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-87

Appx MT1-88
Event Event Source Description
%1 (%2) : WaitForSingleObject Error [%3] %1 (%2) : Pipe Send Error [%3] %1 (%2) : Pipe Recv Error [%3] %1 (%2) : Pipe Send Retry Over %1 (%2) : Pipe Connection Timeout %1 (%2) : Create IP Info Error %1 (%2) : Patient Online Mode Error %1 (%2) : Recv Error (External Device)%n Device [%3]%n Error [%4] %1 (%2) : Shared Memory Write Error [%3] Program error. Program error. Program error. Program error. Program error. Program error. Program error. Program error.

Causes

Remedies

Remarks

13409 FFInput 13410 FFInput 13411 FFInput 13412 FFInput 13413 FFInput 13414 FFInput 13415 FFInput 13416 FFInput

13417 FFInput 13418 FFInput 13419 FFInput 13445 FFInput 13446 FFInput 13447 FFInput 13448 FFInput 13449 FFInput 13450 FFInput 13451 FFInput

%1 (%2) : Shared Memory Delete Program error. Error [%3] %1 (%2) : Failed in Menu Clear.%nInternal Error in IIP[%3] %1 (%2) : Failed in Ip Shelter.%nInternal Error in IIP [%3] %1 (%2) : Failed in Ip Set. %nInternal Error in IIP [%3] %1 : IipInput.exe [Starts]%n %2%n %3 %1 : IipInput.exe [Normal Termination] %1 : IipInput.exe [Forced Termination] %1 (%2) : Image Display Failure InImg> %1 (%2) : Failed in Get Ip Information Response. %nConnection Error to Builtin [%3] %1 (%2) : Failed in Range Over[%3: %4] Program error. Program error. Program error. IipInput.exe is started (information). IipInput.exe is terminated (information). IipInput.exe is terminated (information). Program error. The line was abnormal. Check the 550X unit (power supply, cable, etc.). This is not error information. This is not error information. This is not error information.

13453 FFInput

Program error.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-88

Appx MT1-89
Event Event Source Description
%1 (%2) : Failed in Ip Information Search. %nInternal Error in IIP %1 (%2) : Failed in Ip Information Search. %nTime Out %1 (%2) : Failed in Ip Information Search. %nExamination Register Error.[IDT4] %1 (%2) : Image Processing Information <InImg> %1 (%2) : Failed in Connection Between Reader and Console. %nIIP[%3]%nRU[%4] %1 (%2) : Send Data Error.[RIS] %1 (%2) : RIS Start Error. %1 (%2) : Change Error to Nondisplay Mode.[RIS] Program error. Program error. Program error. Program error. Program error. Program error. This event occurs when an image processing parameter file is not found. Change the SysConfig settings for the CR-IR 391CL or change the RU connection style.

Causes

Remedies

Remarks

13454 FFInput 13455 FFInput 13456 FFInput 13457 FFInput 13458 FFInput 13463 FFInput 13464 FFInput 13465 FFInput 13466 FFInput 13467 FFInput 13468 FFInput 13469 FFInput 13470 FFInput 13471 FFInput 13472 FFInput

%1 (%2) : Change Error to Display Program error. Mode.[RIS] %1 (%2) : Failed in Ordering Data. Program error. [RIS] %1 (%2) : Exposure-Data Send Error.[RIS] Program error.

%1 (%2) : Examination-End Send Program error. Error.[RIS] %1 (%2) : Exposure Menu Register Error. %1 (%2) : All Exposure Menu Register Error. The exposure menu received as the ordering information was not registered. The exposure menu received as the ordering information was not registered. Register the exposure menu with the user utility. Register the exposure menu with the user utility. Select a menu for which an exposure process has not been performed.

%1 (%2) : Selected Menu is Done. The exposure process for the selected XCON Result Information is exposure menu was already performed. annulled. [%3] The result data received from the XCON will be discarded. %1 (%2) : Menu is not Selected. XCON Result Information is annulled. [%3]

13473 FFInput 13474 FFInput 13475 FFInput 13476 FFInput


020-221-01E 04.28.2009 FM5535

No exposure menu was selected. The Select a menu for which an exposure result data received from the XCON will be process has not been performed. discarded. Reregister the XCON parameter with the user utility.

%1 (%2) : Exceeded the Limitation The XCON parameter was improperly set. Value of XCON Exposure Data. [%3 = %4] %1 (%2) : Failed in Ordering Data. Illegal data was contained in the study [RIS] information received from the RIS. %1 (%2) : Failed in Ordering Data Program error. Convert. Internal Error.

CR-IR 391CL Service Manual

Appx MT1-89

Appx MT1-90
Event Event Source Description
%1 (%2) : Exposure Menu Register Error. %1 (%2) : All Exposure Menu Register Error. %1 (%2) : Failed in Examination End Command.[Ris] %1 (%2) : Failed in Communication with RIS. [%3]%n[%4] %1 (%2) : Illegal Number of Selected Item <IdHome> %1 (%2) : Proc UID Get Error <IdHome> %1 (%2) : Menu is not Selected. Failed in Getting ID Information %1 (%2) : Failed in the System Start. [Error: OpDcmStandardDx or MenuData.mdb] %1 (%2) : Proc UID Get Error <IdHome> %1 (%2) : Host Name Get Error <IdHome> %1 (%2) : BCR Search Error. [%3:ErrorCode = %4]<%5> %1 (%2) : MCR Search Error. [%3:ErrorCode = %4]<%5> %1 (%2) : failed in deleting multibyte data

Causes
The exposure menu received as the ordering information was not registered. The exposure menu received as the ordering information was not registered. The order exposure study termination signal was received from the RIS although an order exposure was not received. Program error. The problem is attributable to a disconnected line. Invalid parameter. Program error. Program error. An ID acquisition request was received from built-in type equipment although no exposure menu was selected. Inappropriate installation.

Remedies
Register the exposure menu with the user utility. Register the exposure menu with the user utility. Check the RIS settings. Check the equipment and cables.

Remarks

13477 FFInput 13478 FFInput 13479 FFInput 13480 FFInput

13481 FFInput 13482 FFInput 13483 FFInput 13484 FFInput

Make a menu selection and then press the OK button on the built-in type Console. Reinstall the system to secure matching between DX option and menu database.

13485 FFInput 13486 FFInput 13487 FFInput 13488 FFInput 13497 FFInput 13900 FFInputEz

Program error. Program error. Program error. Program error. Program error. (Not used.) Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

%1 : Registry Value Get/Set Error Information was not successfully acquired [Key] %2 from the registry. [Exp] %3 %4 %5

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-90

Appx MT1-91
Event Event Source Description
%1 : Database Connection Error [DB] %2 [Exp] %3 %4 %5

Causes

Remedies

Remarks

13901 FFInputEz

An attempt to establish the connection to a Check whether the SQL service manager (Not used.) database failed. is operating normally. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. (Not used.) Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. (Not used.) Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Correct the abnormal patient information, and transmit the corrected patient information from the receipt computer. (Not used.) (Not used.)

13902 FFInputEz

%1 : Database Data Get/Set Error A database information acquisition or [DB] %2 storage failed. [Table] %3 [Field] %4 [Exp] %5 %1 : DDO Data Get/Set Error [Tag] %2 %3 %4 %5 %1 : Other Error [Procedure] %2 [ErrorCode] %3 [Exp] %4 %5 %1 : [Starts] %2 %3 %4 %5 %1 : [Normal Termination] %2 %3 %4 %5 %1 : [Forced Termination] %2 %3 %4 %5 Undefined Error, Component is [%1], Procedure is [%2], Msg is [%3] %1 (%2) : [%3] %1 (%2) : Unknown Error%n Error Code [%3] The information acquisition/storage operation was not successfully performed in relation to the image information file (DDO). Abnormal patient information was transmitted from the receipt computer.

13903 FFInputEz

13904 FFInputEz

13910 FFInputEz

(Not used.)

(Not used.)

13911

FFInputEz

(Not used.)

(Not used.)

(Not used.)

13912 FFInputEz

(Not used.)

(Not used.)

(Not used.)

13998 FFInput 13998 FFInput 13999 FFIdDepartSelect

Program error. General information event log. Program error. This is not error information.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-91

Appx MT1-92
Event Event Source Description
%1 (%2) : Unknown Error%n Error Code [%3] %1 (%2) : Unknown Error%n Error Code [%3] %1 (%2) : Unknown Error%n Error Code [%3] [%s] %s (%s) : %s> Unknown Error %1 (%2) : Unknown Error%n Error Code [%3] Logical Program Error. %n %1 %n %2 Catch Exception Error. %n %1 %n %2 Retry is success. %n %1 %n %2 Catch DB exception. %n %1 %n %2 ADO Instance Error. %n %1 %n %2 DB Connect Error. %n %1 %n %2 StoredParam Error. %n %1 %n %2 Variant Empty Error. %n %1 %n %2 Invalid Retry Num. %n %1 %n %2 Invalid Ex. %n %1 %n %2 It failed in the convert of client IP_Address. Program error. Program error. Program error. Program error. Program error. A program error occurred. An exception error occurred. The database access was successfully retried. A warning was issued when an attempt was made to access a database. An error occurred when an attempt was made to access a database. An error occurred when an attempt was made to connect the database. An error occurred when an attempt was made to access a database. An error occurred when an attempt was made to access a database. An error occurred when an attempt was made to access a database. An error occurred when an attempt was made to access a database. A program error occurred. Restart the server computer. Restart the server computer. There is no particular problem. There is no particular problem. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. The program might be faulty. Check the operations performed before and after the error occurrence, and obtain the maintenance log with the Backup Utility. Send then the maintenance log to the manufacturer. Proceed with the processing. The program might be faulty. Check the operations performed before and after the error occurrence, and obtain the maintenance log with the Backup Utility. Send then the maintenance log to the manufacturer. Proceed with the processing. (Not used.) [%1, %2]: Detailed information (Not used.) [%1, %2]: Detailed information [%1, %2]: Detailed information [%1, %2]: Detailed information (Not used.) [%1, %2]: Detailed information (Not used.) [%1, %2]: Detailed information (Not used.) [%1, %2]: Detailed information (Not used.) [%1, %2]: Detailed information (Not used.) [%1, %2]: Detailed information (Not used.) [%1, %2]: Detailed information

Causes

Remedies

Remarks

13999 FFIdMenuChange 13999 FFIdParamedic Select 13999 FFIdPatInfoInput 13999 FFInput 13999 FFIdIndividualSelect 14000 FFDataBaseCtrl 14001 FFDataBaseCtrl 14002 FFDataBaseCtrl 14003 FFDataBaseCtrl 14004 FFDataBaseCtrl 14005 FFDataBaseCtrl 14006 FFDataBaseCtrl 14007 FFDataBaseCtrl 14008 FFDataBaseCtrl 14009 FFDataBaseCtrl 14625 FCRWeb

14626 FCRWeb

It failed in the acquisition of the client mode.

A program error occurred.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-92

Appx MT1-93
Event Event Source Description Causes Remedies
Restart the server application and client (Not used.) application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

14900 FFInputEz

%1 : Registry Value Get/Set Error Information was not successfully acquired [Key] %2 from the registry. [Exp] %3 %4 %5 %1 : Database Connection Error [DB] %2 [Exp] %3 %4 %5

14901 FFInputEz

An attempt to establish the connection to a Check whether the SQL service manager database failed. is operating normally Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client (Not used.) application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. (Not used.) Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

14902 FFInputEz

%1 : Database Data Get/Set Error A database information acquisition or [DB] %2 storage failed. [Table] %3 [Field] %4 [Exp] %5 %1 : DDO Data Get/Set Error [Tag] %2 %3 %4 %5 %1 : Other Error [Procedure] %2 [ErrorCode] %3 [Exp] %4 %5 ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nSystem error The information acquisition/storage operation was not successfully performed in relation to the image information file (DDO). Abnormal patient information was transmitted from the receipt computer, or the transmitted patient information was not successfully operated on. An exception error occurred.

14903 FFInputEz

14904 FFInputEz

19102 FCRWeb

Restart both the server application and client application. If the same error recurs, perform a reinstallation.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

19141 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nex

An exception error occurred.

Restart both the server application and client application. If the same error recurs, perform a reinstallation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-93

Appx MT1-94
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nPadding of IP-address is failed.

Causes
IP address padding failed due to an exception error.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

19227 FCRWeb

19228 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nPadding of IP-address is failed.

IP address padding failed due to an exception error.

Restart. If the same symptom recurs, perform a reinstallation.

19300 UserAuth

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nUnknown Error.

An unknown error occurred during initialization process.

Restart. If the same symptom recurs, perform a reinstallation.

19400 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe uncertain cause error occurred.

An unknown error occurred during initialization process.

Restart. If the same symptom recurs, perform a reinstallation.

19401 FFCustomMsgBox

An error has occurred.

An unknown error occurred.

Restart the server application and the client application. If the same error occurs, restart the system. If the system restarting does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

19706 GeneralImageInfo AccessCom

Logical error.

A program error occurred.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-94

Appx MT1-95
Event Event Source Description Causes Remedies
Restart the server application and client (Not used.) application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

19900 FFInputEz

%1 : Registry Value Get/Set Error Information was not successfully acquired [Key] %2 from the registry. [Exp] %3 %4 %5 %1 : Database Connection Error [DB] %2 [Exp] %3 %4 %5

19901 FFInputEz

An attempt to establish the connection to a Check whether the SQL service manager (Not used.) database failed. is operating normally. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client (Not used.) application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. (Not used.) Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart. If the same symptom recurs, perform a reinstallation. (Not used.)

19902 FFInputEz

%1 : Database Data Get/Set Error A database information acquisition or [DB] %2 storage failed. [Table] %3 [Field] %4 [Exp] %5 %1 : DDO Data Get/Set Error [Tag] %2 %3 %4 %5 %1 : Other Error [Procedure] %2 [ErrorCode] %3 [Exp] %4 %5 It failed in CreateProcess. It has the possibility that an executive file doesnt exist. The start treatment cant be continued. /CtrlProc:RunProc () %1 The information acquisition/storage operation was not successfully performed in relation to the image information file (DDO). The internal setup information was not successfully acquired.

19903 FFInputEz

19904 FFInputEz

20001 FFCtrlProc

Subprocess startup failed. The system is Restart. If the same symptom recurs, unstable or the necessary executable file is perform a reinstallation. missing.

20002 FFCtrlProc 20003 FFCtrlProc

Process start information is An illegal parameter was used for process unusual. The start treatment cant startup. The contents of the process be continued. /CtrlProc:RunProc () information database might be incorrect. It failed in the completion message preparation treatment. The treatment cant be continued. /CtrlProc:EndProc () A process termination request message was not successfully created. This error is attributable to resource insufficiency or system instability.

Restart. If the same symptom recurs, perform a reinstallation. Restart.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-95

Appx MT1-96
Event Event Source Description
It failed in the completion message transmitting treatment. The treatment cant be continued. /CtrlProc:EndProc () It failed in the switching message preparation treatment. The treatment cant be continued. /CtrlProc:ChangeProc () It failed in the switching message transmitting treatment. The treatment cant be continued. /CtrlProc:ChangeProc () It failed in CreateProcess. It has the possibility that an executive file doesnt exist. The start treatment cant be continued. /CtrlProc:SetInitProcEnd () A data transfer error occurred in communications between processes. An attempt to acquire system settings failed. The automatic study data delete function went down because an error occurred in an attempt to automatically delete study data. A database access error occurred. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nBecause the error had occurred, the Study DB capacity adjustment thread was stopped. \nPlease reactivate server PC.

Causes
A process termination request message was not successfully transmitted. This error is attributable to an inoperative transmission destination process or an incorrect transmission destination. The message for showing/hiding the window was not successfully generated. This error is attributable to resource insufficiency or system instability. The message for showing/hiding the window was not successfully transmitted. This error is attributable to an inoperative transmission destination process or an incorrect transmission destination. Subprocess startup failed or the subprocess to be started was not found. Restart.

Remedies

Remarks

20004 FFCtrlProc

20005 FFCtrlProc

Restart.

20006 FFCtrlProc

Restart. If the same symptom recurs, perform a reinstallation.

20007 FFCtrlProc

Restart. If the same symptom recurs, perform a reinstallation.

20052 FFCustomMsgBox 20054 FFCustomMsgBox 20062 FFCustomMsgBox

The program might be stopped.

Restart the server computer. The process can continue with the standard setting values though it may not function normally. Restart the server computer.

20062 FFRoutine

An internal system error occurred when an Restart. If the same symptom recurs, attempt was made to automatically delete perform a reinstallation. study data.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20063 FFCustomMsgBox

The automatic image data delete function went down because an error occurred in an attempt to automatically delete image data.

Restart the server computer.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-96

Appx MT1-97
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nBecause the error had occurred, the HDD capacity adjustment thread was stopped. \nPlease reactivate server PC.

Causes

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20063 FFRoutine

An internal system error occurred when an Restart. If the same symptom recurs, attempt was made to automatically delete perform a reinstallation. image data.

20064 FFCustomMsgBox

The automatic patient information delete function went down because an error occurred in an attempt to automatically delete patient information. A database access error occurred. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nBecause the error had occurred, the Patient DB capacity adjustment thread was stopped. \nPlease reactivate server PC.

Restart the server computer.

20064 FFRoutine

An internal system error occurred when an Restart. If the same symptom recurs, attempt was made to automatically delete perform a reinstallation. patient information.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20065 FFCustomMsgBox

A function to automatically delete uncontrolled/temporarily stored images went down because an error occurred with that processing. A database access error occurred. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nBecause the error had occurred, the Reference Images delete thread was stopped. \nPlease reactivate server PC.

Restart the server computer.

20065 FFRoutine

An internal system error occurred when an Restart. If the same symptom recurs, attempt was made to automatically delete perform a reinstallation. a temporal/stored image.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20071 FFCustomMsgBox

[20071] Failed in the output of Just as the message states. image. > Check the study that is not yet output or the output device and try again.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-97

Appx MT1-98
Event Event Source Description Causes Remedies Remarks
20072 FFCustomMsgBox [20072] Failed in saving JPEG/ Just as the message states. BMP file as the Patient ID contains invalid character for file name. > Delete the following characters from the Patient ID and try again. + , /, : ,*, ?, , <, >, | Initialization process of linkage with the receipt computer function failed. ErrorCode:%1%nSubSystem:%2 The function for linkage with the receipt %nSourceFile:%3%nSpotCode:% computer was not successfully initialized. 4%nFFStdReceCom Initialize Error (FujitsuStdReceCom Initialize Error):%5%n System settings may not have been finished correctly. Contact your service engineer. Check the system settings. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20073 FFCustomMsgBox 20073 FFRoutine

20074 FFCustomMsgBox 20074 FFRoutine

Patient information transferred from the receipt computer is illegal. ErrorCode:%1%nSubSystem:%2 Illegal patient information was transmitted %nSourceFile:%3%nSpotCode:% from the receipt computer. 4%nThe data received by the receipt computer is illegal.

Confirm the unregistered patient information and re-register. Check for unregistered patient information, %1= Error Code: The code that uniquely and then perform the registration procedure identifies an error. again. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Ensure that the network has been connected correctly to the receipt computer. Check the network connection to the receipt computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20075 FFCustomMsgBox 20075 FFRoutine

A communication error occurred with the receipt computer. ErrorCode:%1%nSubSystem:%2 An abnormality occurred in the %nSourceFile:%3%nSpotCode:% communication with the receipt computer. 4%nAbnormality occurred by the communication with the receipt computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-98

Appx MT1-99
Event Event Source Description
A creation of a patient information file failed while processing data from the receipt computer. ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode:% 4%nIt failed in the generation of the patient information file. The patient information file was not successfully created when an attempt was made to process the data received from the receipt computer.

Causes

Remedies
Confirm the disk space and re-register. Check the amount of free disk space, and then perform the registration procedure again.

Remarks

20076 FFCustomMsgBox 20076 FFRoutine

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20077 FFCustomMsgBox

An access to the patient information database failed while processing data from the receipt computer. ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode:% 4%nIt failed in the access to the data base. The patient information database was not successfully accessed when an attempt was made to process the data received from the receipt computer.

Restart the server computer and retry. Contact your service engineer if the same symptom recurs even after it has been restarted. Restart the server computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20077 FFRoutine

20078 FFCustomMsgBox 20078 FFRoutine

Processing a patient information file failed while handling data from the receipt computer. ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode:% 4%nIt failed in the file processing of patient information. The patient information file was not successfully processed when an attempt was made to process the data received from the receipt computer.

Confirm the unregistered patient information and re-register. Check for unregistered patient information, %1= Error Code: The code that uniquely and then perform the registration procedure identifies an error. again. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Confirm the unregistered patient information and re-register. The patient information file was not successfully analyzed when an attempt was made to process the data received from the receipt computer. Check for unregistered patient information, %1= Error Code: The code that uniquely and then perform the registration procedure identifies an error. again. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20079 FFCustomMsgBox 20079 FFRoutine

A patient information file analysis failed while handling data from the receipt computer. ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode:% 4%nIt failed in the analysis of the file of patient information.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-99

Appx MT1-100
Event Event Source Description
An acquisition of option information failed. ErrorCode:%1%nSubSystem:%2 The option information was not %nSourceFile:%3%nSpotCode:% successfully acquired. 4%nIt failed in the acquisition of option key information on receipt computer communication.\n The default value is used.

Causes

Remedies
The process can continue with the standard setting values though it may not function normally. Install the option key for linkage with the receipt computer.

Remarks

20080 FFCustomMsgBox 20080 FFRoutine

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20081 FFCustomMsgBox 20081 FFRoutine

An Access to the directory setting file failed. ErrorCode:%1%nSubSystem:%2 The directory setup file was not %nSourceFile:%3%nSpotCode:% successfully accessed. 4%nIt failed in the acquisition of directory information.\n The default value is used.\n

The process can continue with the standard setting values though it may not function normally. Reinstall the system. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20082 FFCustomMsgBox

A fatal error occurred in the linkage with the receipt computer.

Restart the server computer and retry. Contact your service engineer if the same symptom recurs even after it has been restarted. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Main Main

20082 FFRoutine

ErrorCode:%1%nSubSystem:%2 A fatal error occurred when an attempt was Restart the server computer. %nSourceFile:%3%nSpotCode:% made to execute the function for linkage 4%nThe fatal error occurred by with the receipt computer. the communication with the receipt computer.\nPlease reactivate server PC.

20102 FFCustomMsgBox 20104 FFCustomMsgBox 20104 FFMain

Setup incompleted.

Application key software is not installed.

Install the application key.

Failed in securing system settings. It is conceivable that the file was damaged Restart. If the same symptom recurs, or deleted. perform a reinstallation. It failed in the acquisition of the configuration information. The initialization treatment cant be continued. /MainProcess:Main () An attempt to acquire the configuration information failed. The problem is attributable to improper installation or system instability. Restart. If the same symptom recurs, perform a reinstallation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-100

Appx MT1-101
Event Event Source Description
Failed in accessing the process control database. It failed in the acquisition of the process information data base. The initialization treatment cant be continued. /MainProcess:Main () Failed in accessing the message distribution control database. It failed in opening of the message data base. The initialization treatment cant be continued. /MainProcess:Main () Failed in process activation. It failed in the start of the subprocess. The initialization treatment cant be continued. /MainProcess:Main () Failed in initialization processing.

Causes
Data was not successfully acquired from the process information database. This error is attributable to improper installation or system instability.

Remedies
Main Restart. If the same symptom recurs, perform a reinstallation. Main

Remarks

20105 FFCustomMsgBox 20105 FFMain

It is conceivable that the file was damaged Restart. If the same symptom recurs, or deleted. perform a reinstallation.

20106 FFCustomMsgBox 20106 FFMain

It is conceivable that the file was damaged Restart. If the same symptom recurs, or deleted. perform a reinstallation. The message database was not successfully opened. This error occurred due to an improper installation or system instability. A subprocess was not successfully started up for some reason. Subprocess startup failed. This error is attributable to improper installation or system instability. The subprocess failed to start up. It is conceivable that the system is unstable. Restart. If the same symptom recurs, perform a reinstallation.

20108 FFCustomMsgBox 20108 FFMain

View the event logs around to examine the Main cause. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Main

20110 20110

FFCustomMsgBox FFMain

The subprocess failed to start up. It failed in the start of the subThis error is attributable to improper process. The initialization treatment cant be continued. installation or system instability. /MainProcess:m_ProcessControl_ OnRunProcComplete () Failed in process termination. An error occurred for some reason during subprocess end processing

20118 20118

FFCustomMsgBox FFMain

Nothing particular. Restart.

Main

It failed in the completion of the The subprocess was not successfully sub-process. /MainProcess:Proce terminated. It is conceivable that the ssEndRequirement () system was unstable. Failed in process switchover. It failed in switching of the process. /MainProcess:xxxxx Startup processing was discontinued because the SQL server was not up and running. A subprocess was not successfully controlled for some reason. Subprocess changeover failed. This error is attributable to an inactive subprocess or system instability. Restart the server computer.

20124 FFCustomMsgBox 20124 FFMain 20140 FFCustomMsgBox

View the event logs around to examine the Main cause. Restart.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-101

Appx MT1-102
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nBecause SQL Server did not operate, the start processing in the MainProcess was discontinued. %n Please reactivate server PC after installing SQL Server. System startup processing aborted because the IIS has not started. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nBecause IIS (Internet Information Service) did not operate, the start processing in the MainProcess was discontinued. %n Please reactivate server PC after installing IIS. System startup processing aborted because Backup Utility, User Utility or Service Utility has started.

Causes
The startup process for the main process was aborted because the SQL server was not running.

Remedies

Remarks

20140 FFMain

Start the SQL server and restart the server %1= Error Code: The code that uniquely application. identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart the server computer. Start the SQL server and restart the server %1= Error Code: The code that uniquely application. identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Shutdown the Utility and retry.

20141 FFCustomMsgBox 20141 FFMain

The IIS is not running. The startup process for the main process was aborted because the IIS was not running.

20143 FFCustomMsgBox

The Backup Utility, User Utility, or Service Utility is running.

20143 FFMain

Exit the utility and then restart the server ErrorCode:%1%nSubSystem:%2 The startup process for the main process %nSourceFile: %3%nSpotCode: was aborted because a utility was running. application. %4%nBecause utility started, the start processing in the MainProcess was discontinued. %n Please reactivate the MainProcess after ending utility. Startup of Backup Utility failed. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the start of the backup utility.%n Please reactivate server PC. Restart the server computer. An attempt to start the Backup Utility failed. Restart the server PC and then retry. This failure is attributable to OS resource insufficiency.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20147 FFCustomMsgBox 20147 FFMain

20148 FFCustomMsgBox

Startup of Service Utility failed.

Restart the server computer.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-102

Appx MT1-103
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the start of the service utility.%n Please reactivate server PC.

Causes
The Service Utility was not successfully started. This error is attributable to OS resource insufficiency.

Remedies
Restart the server PC and then retry.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20148 FFMain

20149 FFCustomMsgBox 20149 FFMain

Startup of User Utility failed. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the start of the user utility.%n Please reactivate server PC. An attempt to start the User Utility failed. This error is attributable to OS resource insufficiency.

Restart the server computer. Restart the server PC and then retry.

20154 FFCustomMsgBox 20154 FFMain

Failed in accessing the character string database. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed from LangStr.MDB to the acquisition of the character string.%n Please reactivate server PC.

The problem is attributable to the character string database. A character string was not successfully acquired from the character string database. The database might be damaged. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20156 FFCustomMsgBox

System startup processing aborted because acquisition of software version information failed. Event resources used for notifying the client of the server status could not be secured. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the notification that the server starts. %n Please reactivate server PC.

Registry information may have been damaged.

Restart the server computer.

20157 FFCustomMsgBox 20157 FFMain

Restart the server computer. The server startup status notification process failed. This error is attributable to OS resource insufficiency. Restart the server application. If the same error recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MT1-103

Appx MT1-104
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nInformation.

Causes
Information (the information is set forth below). Server application version information.

Remedies
Nothing particular.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20158 FFMain

20159 FFMain

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in reading the Bitmap file.%n Please reactivate server PC.

An attempt to read the bitmap file failed. The file may be damaged.

Restart the server PC and retry.

20160 FFCustomMsgBox 20160 FFMain

Startup of the disk tool failed. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the start of the disk copy tool.%n Please reactivate server PC. The disk copy tool was not successfully started. The error is attributable to OS resource insufficiency.

Restart the server computer. Restart the server PC and then retry.

20161 FFCustomMsgBox 20163 FFCustomMsgBox 20167 FFMain

Writing the OS onto the event log was disabled. The server application has already been up and running. Checking of the endoscope image A failure occurred in an attempt to confirm reception of an endoscopic image folder. receiving folder has failed.%n Restart the server computer and check the setting for endoscope image import function.%n Contact your service engineer if the same symptom recurs even after it has been restarted. %n Initialization has incompleted. *Image viewer may not work correctly. Restart Client Application. Use of these search conditions is disabled as they are in actual use at present. An exception might have occurred.

Restart the server computer.

Restart the server computer and check setup conditions of the endoscopic image import function. If the same error recurs, reinstall the program. If the situation still does not improve, check conditions of the error occurrence and submit the related event log to the manufacturer. Restart the client application. If the problem still exists, contact your service engineer.

20200 FFCustomMsgBox

20300 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-104

Appx MT1-105
Event Event Source Description
Search conditions are deleted. These search conditions cannot be changed because they have already been determined. An attempt to acquire search conditions resulted in a failure. Display of search conditions edit window resulted in a failure. Storage of new search conditions resulted in a failure. Orderly arrangements of search conditions terminated abnormally. Storage of updated search conditions resulted in a failure. A failure occurred when setting initial search conditions. A failure occurred when setting initial search conditions. A failure occurred when setting initial search conditions. An error occurred at startup of the image viewer. An error occurred at startup of the study start window. An error occurred at startup of the study edit window. An error occurred while handling lock processing to delete studies. An error occurred while handling unlock processing to delete studies. An error occurred in an attempt to acquire disk information. An error occurred in an attempt to acquire disk information. An error occurred when deleting a study. An error occurred at startup of the C@Rna study reservation window. Studies are locked by another user. Check connection to the server computer and then retry. Check connection to the server computer and then retry. Check connection to the server computer and then retry. Retry. Retry. Check connection to the server computer and then retry. Unlock studies and retry. Check connection to the server computer and then retry. Check connection to the server computer and then retry. Check connection to the server computer and then retry. Check connection to the server computer and then retry. Check connection to the server computer and then retry. Check connection to the server computer and then retry. Check connection to the server computer and then retry. Check connection to the server computer and then retry. Check connection to the server computer and then retry. Check connection to the server computer and then retry.

Causes

Remedies
Press OK to delete the search conditions. Otherwise, press Cancel.

Remarks

20301 FFCustomMsgBox 20303 FFCustomMsgBox 20305 FFCustomMsgBox 20306 FFCustomMsgBox 20307 FFCustomMsgBox 20308 FFCustomMsgBox 20309 FFCustomMsgBox 20311 FFCustomMsgBox

20312 FFCustomMsgBox 20313 FFCustomMsgBox 20314 FFCustomMsgBox 20315 FFCustomMsgBox 20316 FFCustomMsgBox 20317 FFCustomMsgBox 20318 FFCustomMsgBox 20319 FFCustomMsgBox 20320 FFCustomMsgBox 20321 FFCustomMsgBox 20322 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-105

Appx MT1-106
Event Event Source Description
An error occurred during film output processing. [20324] An error occurred while JPEG/BMP file is being output. > Check the connection to the network cable and try again. + If it does not resolve, contact your service engineer. An error occurred during storage disk output processing. An error occurred during work disk output processing. An error occurred when processing transfer of image data to the C@Rna data center. Selected studies are deleted. Necessary processing was disabled. Selected studies might have been deleted. A failure occurred when searching for study data within a disk [20335] Layout of the screen was Just as the message states. not performed correctly. *Ensure that the network cable has been connected correctly and retry. >Contact your service engineer if the same symptom recurs even after it has been retried. Some of the studies have been locked. All of the selected studies have been locked. The current user will be logged off the system. Application will be terminated. Communication with the EMR resulted in a failure. The study is locked by another user. Press OK to continue the process. Otherwise, press Cancel. Unlock such studies and then retry. Press OK to log off. Otherwise, press Cancel. Press OK to shut down the system. Otherwise, press Cancel. Confirm connection to the EMR device and retry. Just as the message states.

Causes

Remedies
Check connection to the server computer and then retry.

Remarks

20323 FFCustomMsgBox 20324 FFCustomMsgBox

20325 FFCustomMsgBox 20326 FFCustomMsgBox 20327 FFCustomMsgBox 20328 FFCustomMsgBox 20330 FFCustomMsgBox

Check connection to the server computer and then retry. Check connection to the server computer and then retry. Check connection to the server computer and then retry. Press OK to delete the selected studies. Otherwise, press Cancel. Retry.

20332 FFCustomMsgBox 20335 FFCustomMsgBox

Check connection to the server computer and then retry.

20336 FFCustomMsgBox 20337 FFCustomMsgBox 20338 FFCustomMsgBox 20339 FFCustomMsgBox 20341 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-106

Appx MT1-107
Event Event Source Description
The system has not been logged on. The system has been logged off. The system has been either logged off or logged on by different users. You are not authorized to perform this operation. An error occurred. The processing cannot be continued in the specified study. [20351] A study is being performed *Please Complete or Suspend ongoing study. >If the computer currently in use is unable to check, the study may be used by other user. >Otherwise, please restart all computers of this system. [20352] A study is being performed. *Please Complete or Suspend ongoing study. >If the computer currently in use is unable to check, the study may be used by other user. >Otherwise, please restart all computers of this system. The study cannot be processed because it is controlled. The study cannot be processed because it is uncontrolled. [20355] The operation cannot be Just as the message states. performed because the study status is Reservation. *Please try again after completing the study. [20356] The operation cannot be Just as the message states. performed because the study status is Exposing. *Please try again after completing the study. The study is locked by another user. Just as the message states.

Causes

Remedies
Retry after you have logged on the system. Retry after you have logged on the system. Retry after you have logged on the system. Log onto the system with a properly authorized user name to retry this operation. Check the connection, and then retry. Unlock such study and then retry.

Remarks

20342 FFCustomMsgBox 20343 FFCustomMsgBox 20344 FFCustomMsgBox 20345 FFCustomMsgBox 20346 FFCustomMsgBox 20350 FFCustomMsgBox 20351 FFCustomMsgBox

20352 FFCustomMsgBox

Just as the message states.

20353 FFCustomMsgBox 20354 FFCustomMsgBox 20355 FFCustomMsgBox

20356 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-107

Appx MT1-108
Event Event Source Description
[20357] The operation cannot be performed because the study status is Finish Exposure. *This feature is available to the studies that have been Verified. The operation cannot be performed because the study status is Verified. The study cannot be processed because the storage/print status is Waiting. The study cannot be processed because the storage/print status is Processing. The study cannot be processed because storage or printing has already been done. The study cannot be processed because it is locked so as not to be deleted. The study cannot be processed because it is unlocked so as to be deleted. The study cannot be processed because it is uncontrolled. The study cannot be processed because there are some unexposed menus. The study cannot be processed because all menus remain unexposed. The study cannot be processed because all images are effective. An attempt to acquire IP address of this equipment resulted in a failure. An attempt to acquire IP address of the EMR resulted in a failure. Settings for the use of EMR have not been activated. A failure occurred in an attempt to cancel image capture processing. Image acquisition failed. All menus are unexposed. All images are effective. Retry after you have logged on the system. Retry after you have logged on the system. Activate the settings for the use, and then retry.

Causes
Just as the message states.

Remedies

Remarks

20357 FFCustomMsgBox

20358 FFCustomMsgBox 20359 FFCustomMsgBox 20360 FFCustomMsgBox 20361 FFCustomMsgBox 20362 FFCustomMsgBox 20363 FFCustomMsgBox 20364 FFCustomMsgBox 20365 FFCustomMsgBox 20366 FFCustomMsgBox 20367 FFCustomMsgBox 20369 FFCustomMsgBox 20370 FFCustomMsgBox 20371 FFCustomMsgBox 20375 FFCustomMsgBox 20376 FFCustomMsgBox
020-221-02E 01.08.2010 FM5563

Select Image Viewer to confirm the image.

CR-IR 391CL Service Manual

Appx MT1-108

Appx MT1-109
Event Event Source Description
The drive is in use. The drive has not been connected. No available disk has been inserted. [20380] Certain study could not be Just as the message states. imported. * If the disk is a PDI disk, view the image using a viewer provided with PDI. * When importing from other than a disk for storage, check the patient information, and set up the patient ID correctly. No disk has been inserted into the selected drive. Necessary processing is disabled to perform because the study includes mis-exposed images. Necessary processing is disabled to perform because all images of the study are mis-exposed. Necessary processing was disabled because a failure occurred in an attempt to acquire study status information from the database. Necessary processing was disabled because an exceptional error occurred. An error occurred when registering search conditions. Retry.

Causes

Remedies

Remarks

20377 FFCustomMsgBox 20378 FFCustomMsgBox 20379 FFCustomMsgBox 20380 FFCustomMsgBox

20381 FFCustomMsgBox 20382 FFCustomMsgBox 20383 FFCustomMsgBox 20384 FFCustomMsgBox

20385 FFCustomMsgBox 20390 FFCustomMsgBox

Retry. Ensure that the network cable has been connected correctly and retry. Contact your service engineer if the same symptom recurs even after it has been retried. Do you wish to continue processing? Unexposed menus will be deleted. Studies that have no exposed menus will be deleted. Do you wish to delete unexposed menus? Studies that have no exposed menus will be deleted.

20391 FFCustomMsgBox

Some of the studies cannot be handled. There are some studies including unexposed menu.

20392 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-109

Appx MT1-110
Event Event Source Description
The number of screens that can be displayed exceeded the allowable limit. An error is received from the EMR. A fatal error occurred. No study of patient that is displayed on the EMR exists. An attempt to acquire setting information of the EMR resulted in a failure. Selected image has already been deleted. Selected image of study exists in the local disk. The following error occurred when deleting a study in which all menus remain unexposed. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe C@RnaURL collection is not made. The C@RnaURL collection is not created. This study is being outputted. Check that the C@Rna client is installed. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart this system and retry. Retrieve image data from disks for storage and retry.

Causes

Remedies
Close some windows displaying and retry. Contact your administrator. Contact your administrator.

Remarks

20393 FFCustomMsgBox 20394 FFCustomMsgBox 20395 FFCustomMsgBox 20396 FFCustomMsgBox 20397 FFCustomMsgBox 20398 FFCustomMsgBox 20399 FFCustomMsgBox 20400 FFCustomMsgBox 20401 FCRWeb

20401 FFCustomMsgBox 20402 FCRWeb

The following error occurred when deleting a study in which all menus remain unexposed. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe prohibited character is included. (%5)

The study is locked to delete. An unacceptable character is included in Check the input value. the patient ID. You cannot use , #, %, &, ', +, ?, \, /, , @, 1-byte Katanaka characters, 2-byte characters, or a character string consisting of a blank only. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Input value Unacceptable characters that caused an error to occur.

20402 FFCustomMsgBox

No disk is inserted or the disk has been exchanged for another one.

Insert a correct disk.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-110

Appx MT1-111
Event Event Source Description Causes Remedies
Check that the C@Rna client is installed.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Input value

20403 FCRWeb

ErrorCode:%1%nSubSystem:%2 An attempt to acquire C@RnaURL failed. %nSourceFile: %3%nSpotCode: %4%nIt failed in the acquisition of C@RnaURL.

20403 FFCustomMsgBox 20404 FCRWeb

Image acquisition is canceled. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe number of maximum bytes is exceeded. (%5) The maximum permissible number of bytes Check the input value. was exceeded.

20404 FFCustomMsgBox 20405 FCRWeb

The data received from the EMR is illegal. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe registry key is not found. (%5) The registry key was not found.

Contact your administrator. Check the registry key. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Target registry key

20405 FFCustomMsgBox

The server device could not be accessed. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe number of arrays of property specification values is not corresponding to the number of buttons.

In an environment where multiple client Retry the operation. computers are connected, this can occur If the problem is not resolved, restart the when the study list window is operated with client application. a high server load. An exception occurred when a method for Run Proc execution was used. An internal system error occurred. Restart the server application and client %1= Error Code: The code that uniquely application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20406 FCRWeb

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-111

Appx MT1-112
Event Event Source Description
The number of studies that can be displayed on Viewer exceeded the allowable limit. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed from character string DB to the acquisition of the character string list. A character string list was not successfully acquired from the character string database. The LangStr.mdb file might be missing or damaged.

Causes

Remedies
Reduce the number of studies to be selected and retry. Check LangStr.mdb.

Remarks

20406 FFCustomMsgBox 20407 FCRWeb

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20407 FFCustomMsgBox 20408 FCRWeb

The set contents are possibly incorrect. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nProcessing has already been begun. The request was ignored because the process for acquiring data from the media already started.

Input correctly. Carry it out again after a while. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20408 FFCustomMsgBox 20409 FCRWeb

Failed in output process. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDevice List Get Error! The equipment list could not be acquired. The NetConfig.mdb file might be missing or damaged.

Confirm the status of connection device. Check NetConfig.mdb.

20409 FFCustomMsgBox

Patient ID entered includes characters prohibited to use. ErrorCode:%1%nSubSystem:%2 The NetConfig.mdb file could not be %nSourceFile: %3%nSpotCode: opened. The file might be nonexistent or %4%nNetConfig.mdb Open Error! damaged.

Following characters are not allowed to use for Patient ID. Re-input correctly. # %% && + ? \ / @ en-size-kana em-size-characters spaces-only Check NetConfig.mdb. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20410 FCRWeb

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-112

Appx MT1-113
Event
20411

Event Source
FCRWeb

Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nProcessing has already been begun.

Causes
A process is already started.

Remedies

Remarks

Since a process is being performed, wait a %1= Error Code: The code that uniquely while and then retry. identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20411

FFCustomMsgBox

[20411] An error occurred during the screen display processing. *Restart the client application. >If restarting does not resolve, contact your service engineer. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nRequestProc (%5)

Just as the message states.

20412 FCRWeb

The acquisition request could not be registered. It is conceivable that no medium was connected.

Check that a medium is connected.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Details of requested acquisition

20412 FFCustomMsgBox 20413 FCRWeb

Initialization of Image Link function could not be performed. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nGetRetrieveStatus (%5) All image for the study were not successfully acquired from the media. This error is attributable to an incorrect media connection setting, a disconnected media drive, or a damaged media drive.

System settings may not have been finished correctly. Contact your service engineer. With the Service Utility, check for incorrect %1= Error Code: The code that uniquely media connection settings. Also, check the identifies an error. DVD drive power supply and cable %2= Subsystem: The subsystem where an connections. error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Return value Restart the server computer and retry. Contact your service engineer if the same symptom recurs even after it has been restarted.

20413 FFCustomMsgBox

An error occurred in Image Link function.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-113

Appx MT1-114
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nGetProcStatus (%5)

Causes
One image for the study was not successfully acquired from the media. This error is attributable to an incorrect media connection setting, a disconnected media drive, or a damaged media drive.

Remedies

Remarks

20414 FCRWeb

With the Service Utility, check for incorrect %1= Error Code: The code that uniquely media connection settings. Also, check the identifies an error. DVD drive power supply and cable %2= Subsystem: The subsystem where an connections. error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Return value Contact your service engineer.

20414 FFCustomMsgBox

Patient information file analysis failed when processing data received from the electric medical chart. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nGetNextImageProcStatus (%5) The image recorded on a medium was not successfully registered in the local equipment. This error is attributable to an incorrect media connection setting, a disconnected media drive, or a damaged media drive.

20415 FCRWeb

With the Service Utility, check for incorrect %1= Error Code: The code that uniquely media connection settings. Also, check the identifies an error. DVD drive power supply and cable %2= Subsystem: The subsystem where an connections. error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20415 FFCustomMsgBox

[20415] Failed in saving JPEG/ Just as the message states. BMP file as the Patient ID contains invalid character for file name. > Delete the following characters from the Patient ID and try again. + , /, : ,*, ?, , <, >, | ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe search condition defined from the Hobbit server cannot be acquired. Defined search conditions could not be acquired from the Hobbit server. The database might not be running. Check that the SQL server is running. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20416 FCRWeb

20417 FCRWeb

ErrorCode:%1%nSubSystem: %2%nSourceFile: %3%n SpotCode: %4%nThe numbering processing of the retrieval condition number failed.

The search condition numbering process was not successfully performed. The database might not be running.

Check that the SQL server is running.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-114

Appx MT1-115
Event Event Source Description
ErrorCode:%1%nSubSystem: %2%nSourceFile: %3%n SpotCode: %4%nThere is no pertinent retrieval condition.

Causes
There is no pertinent retrieval condition.

Remedies
Restart the server application.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Return value %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Return value

20418 FCRWeb

20419 FCRWeb

ErrorCode:%1%nSubSystem: An attempt to update a database partly %2%nSourceFile: %3%n failed. The database might not be running. SpotCode:%4%nA part of renewal of DB failed.

Check that the SQL server is running.

20420 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe renewal of DB failed.

An attempt to update a database failed. The database might not be running.

Check that the SQL server is running.

20421 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe renewal of DB failed. (%5)

An attempt to update a database failed. The database might not be running.

Check that the SQL server is running.

20422 FCRWeb

ErrorCode:%1%nSubSystem:%2 The added search conditions could not be %nSourceFile: %3%nSpotCode: acquired. The database might not be %4%nThe added search condition running. cannot be acquired. (%5)

Check that the SQL server is running.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-115

Appx MT1-116
Event Event Source Description Causes Remedies
Check that the SQL server is running.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20423 FCRWeb

ErrorCode:%1%nSubSystem:%2 The added search conditions could not be %nSourceFile: %3%nSpotCode: acquired. The database might not be %4%nThe added search condition running. cannot be acquired.

20424 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nA part of renewal of DB failed.

An attempt to update a database partly failed. The database might not be running.

Check that the SQL server is running.

20424 FFCustomMsgBox

Failed in displaying thumbnail images.

In an environment when multiple client computers are connected, this can occur when the server load is high and selected record switching etc. are performed repeatedly on the study list window. Click the update button on the study list window to display again. An attempt to update a database failed. The database might not be running.

Press the update button on the study list window for re-display.

20425 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe renewal of DB failed.

Check that the SQL server is running.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Query sequence number

20426 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe search condition is not defined. (QuerySeq:%5)

The search conditions were not specified.

Check whether the ListConfigDB T_ MQUERY_DETAIL table and T_MQUERY record exist.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-116

Appx MT1-117
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt started overwriting the search condition that had been selected in a different search condition.

Causes
An attempt was made to overwrite the selected search conditions with different search conditions.

Remedies
Nothing particular.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Search query key %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20427 FCRWeb

20428 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe search condition is not defined. (QueryKey:%5)

Check whether the ListConfigDB T_ MQUERY_DETAIL table and T_MQUERY record exist.

20429 FCRWeb

ErrorCode:%1%nSubSystem:%2 The row for display is not selected. %nSourceFile: %3%nSpotCode: %4%nThe row for the display has not been selected.

Select a row.

20430 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe data type of the row cannot be specified.

The data type of the row cannot be identified. The program might be faulty.

Restart the server application and client %1= Error Code: The code that uniquely application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Check that the SQL server is running. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20431 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred when the retrieval was executed.

An error occurred during a search. The database might not be running.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-117

Appx MT1-118
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred when the retrieval was executed. (%5)

Causes
An error occurred during a search. The database might not be running.

Remedies
Check that the SQL server is running.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Return value %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20432 FCRWeb

20433 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThere is no operation authority.

The current user does not have operating privilege.

Log in as a user with the operating privileges, and then perform the operation again.

20434 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt is not logged in.

The system has not been logged on.

If log-in is not achieved, log in.

20435 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt was logoffed.

You have been logged off the system.

Retry logging onto the system.

20436 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nUser ID is not found.

The user ID was not found.

If log-in is not achieved, log in.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-118

Appx MT1-119
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nURL was not able to be acquired.

Causes
The URL could not be acquired. It is conceivable that the server is not connected.

Remedies
Check the connection to the server.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20437 FCRWeb

20438 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in patient ID acquisition from the electronic clinical record device.

The patient ID was not successfully Check the connection to the electronic acquired from an electronic medical chart. medical chart. This error is attributable to an unconnected electronic medical chart.

20439 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the DB retrieval. (The patients all inspections are retrieved.)

A database search failed (when all patient studies were searched for). The database might not be running.

Check that the SQL server is running.

20440 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the mount.

Mounting failed.

Restart both the server PC and client PC

20441 FCRWeb

ErrorCode:%1%nSubSystem:%2 The row for display is not selected. %nSourceFile: %3%nSpotCode: %4%nThe row for the display has not been selected.

Select a row.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-119

Appx MT1-120
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe data type of the row cannot be specified.

Causes
The data type of the row cannot be identified. The program might be faulty.

Remedies

Remarks

20442 FCRWeb

Restart the server application and client %1= Error Code: The code that uniquely application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Check that the SQL server is running. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Return value %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20443 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred when the retrieval was executed.

An error occurred during a search. The database might not be running.

20444 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred when the retrieval was executed. (%5)

An error occurred during a search (%5). The database might not be running.

Check that the SQL server is running.

20445 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the user information acquisition.

User information acquisition failed. The database might not be running.

Check that the SQL server is running.

20446 FCRWeb

ErrorCode:%1%nSubSystem:%2 The initial search conditions were not %nSourceFile: %3%nSpotCode: successfully updated. The database might %4%nIt failed in the initial retrieval not be running. condition update.

Check that the SQL server is running.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-120

Appx MT1-121
Event Event Source Description Causes Remedies Remarks
20447 FCRWeb ErrorCode:%1%nSubSystem:%2 The initial search conditions were not %nSourceFile: %3%nSpotCode: successfully updated due to an exclusive %4%nThe initial retrieval condition error. update failed because of an exclusive error. Check that the study list is activated by the %1= Error Code: The code that uniquely same user at another machine. identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Check LangStr.mdb. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Character string ID

20448 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed from character string DB to the acquisition of the character string list.

A character string list was not successfully acquired from the character string database. The LangStr.mdb file might be damaged.

20449 FCRWeb

ErrorCode:%1%nSubSystem:%2 The character string was not found in the %nSourceFile: %3%nSpotCode: character string database (ID = %5). %4%nThe character string doesnt The LangStr.mdb file might be damaged. exist in character string DB. (ID=%5)

Check LangStr.mdb.

20450 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe row number of inspection list bind data is not corresponding to the row number of Raoutoskema.

The number of study list bind data rows Restart the server application and client %1= Error Code: The code that uniquely does not agree with the number of layout application. If the same error recurs, identifies an error. schema rows. The program might be faulty. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). The value list could not be acquired. The database might not be running. Check that the SQL server is running. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20451 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe value list cannot be acquired.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-121

Appx MT1-122
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe inspection is not specified.

Causes
No study was specified.

Remedies
Select a study and then retry.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20452 FCRWeb

20453 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt is not logged in.

The system has not been logged on.

If log-in is not achieved, log in.

20454 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nBecause the time-out had been generated, it was logoffed.

Log-off occurred due to a timeout.

Retry logging onto the system.

20455 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe authority was checked by user ID different from the login user.

The user ID used for a privilege check did not match the log-in user. The program might be faulty.

Restart the server application and client %1= Error Code: The code that uniquely application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Log in as a user with operating privileges. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20456 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThere is no user authority.

You do not have user privileges.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-122

Appx MT1-123
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe exception was generated by the operation authority check processing.

Causes

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=XML Filename

20457 FCRWeb

An exception occurred during an operating Restart both the server application and privilege check process. This is an internal client application. If the same error recurs, system error. perform a reinstallation.

20458 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred by the DB component (exclusive registration).

An error occurred in a database component Restart both the server application and (exclusive registration). client application. If the same error recurs, An internal system error occurred. perform a reinstallation.

20459 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe exception was generated by the exclusive registration processing.

An exception occurred during an exclusive Restart both the server application and registration process. client application. If the same error recurs, perform a reinstallation.

20460 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe exception was generated by initial processing of the inspection output.

An exception occurred during the study output initialization process. The program might be faulty.

Restart. If the same symptom recurs, perform a reinstallation.

20461 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in making XML for the output. (%5)

The output XML was not successfully Restart both the server application and created. An internal system error occurred. client application. If the same error recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-123

Appx MT1-124
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the deletion of the exclusive registration ending inspection.

Causes
The exclusively registered study was not successfully deleted. An internal system error occurred.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Return value %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Return value %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Return value

20462 FCRWeb

20463 FCRWeb

ErrorCode:%1%nSubSystem:%2 The URL was not successfully acquired. %nSourceFile: %3%nSpotCode: It is conceivable that the server is not %4%nIt failed in the acquisition of connected. URL. (%5)

Check the connection to the server.

20464 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred by the patient information acquisition processing for the C@Rna inspection reservation specification. (%5)

An error occurred when a patient information acquisition process was performed for C@Rna study scheduling.

Check that the SQL server is running.

20465 FCRWeb

ErrorCode:%1%nSubSystem:%2 An attempt to acquire C@RnaURL failed. %nSourceFile: %3%nSpotCode: The C@RnaURL client might not exist. %4%nIt failed in the acquisition of C@RnaURL. (%5)

Check that the C@Rna client is installed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-124

Appx MT1-125
Event Event Source Description Causes Remedies
Check that the SQL server is running.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Character string ID %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5=Return value %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20466 FCRWeb

ErrorCode:%1%nSubSystem:%2 The study status was not successfully %nSourceFile: %3%nSpotCode: updated. The database might not be %4%nIt failed in the update of the running. inspection status.

20467 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed from character string DB to the acquisition of the character string list.

A character string list was not successfully acquired from the character string database. The LangStr.mdb file might be damaged.

Check LangStr.mdb.

20468 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt was not finding of ID in character string DB. (ID=%5)

The ID was not found in the character string database (ID = %5). The LangStr. mdb file might be damaged.

Check LangStr.mdb.

20469 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred while outputting it. (ReturnCode=%5)

An error occurred during output. This is an internal system error.

Restart. If the same symptom recurs, perform a reinstallation.

20470 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the deletion of the inspection.

Study deletion failed. An internal system error occurred.

Restart both the server PC and client PC

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-125

Appx MT1-126
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe number of arrays of property specification values is not corresponding to the number of buttons.

Causes
An exception occurred when a method for Run Proc execution was used. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20471 FCRWeb

20472 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed from character string DB to the acquisition of the character string list.

A character string list was not successfully acquired from the character string database. The LangStr.mdb file might be damaged.

Check LangStr.mdb.

20473 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe number of arrays of property specification values is not corresponding to the number of buttons.

An exception occurred when a method for Run Proc execution was used. An internal system error occurred.

Restart the server application and client %1= Error Code: The code that uniquely application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Check LangStr.mdb. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

20474 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed from character string DB to the acquisition of the character string list.

A character string list was not successfully acquired from the character string database. The LangStr.mdb file might be damaged.

20484 FCRWeb

ErrorCode:%1%nSubSystem:%2 The patient information file (Karte.xml) was Check whether Karte.xml is damaged or %nSourceFile:%3%nSpotCode:% not successfully monitored. contains wrong data. Also, check whether 4%nSystem Exception Error. the image link function is improperly set.

20560 FFCustomMsgBox

Deletion of study has failed.

This can occur when study deletion is performed simultaneously from multiple computers. (The studies are different studies.)

Retry the operation. If the problem is not resolved, restart the client application.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-126

Appx MT1-127
Event
20611

Event Source
FFCustomMsgBox

Description
[20611] Failed in saving the system settings.

Causes
Environmental failure such as communication failure or database failure has occurred.

Remedies
Contact your customer service.

Remarks

20622 Error

[20622] An attempt to acquire Not used. (does not occur) information from the EMR failed. *Please check the display of EMR, and try again. >Contact your service engineer if the same symptom recurs even after it has been retried. [20623] An error occurred when study started. *Restart the system. >If the same symptom recurs even after performing the above, contact our service engineer. [20635] A fatal error occurred. *Restart the system. >If the same symptom recurs even after performing the above, contact our service engineer. [20662] An attempt to register new study failed. *The original information may have been deleted. [20663] Failed in displaying the Edit/Re-Study screen. *Restart the client application. >If restarting does not resolve, contact your service engineer. [20664] Failed in displaying the Free-Layout screen. *Restart the client application. >If restarting does not resolve, contact your service engineer. [20665] Failed in starting the application. *Only available in the installed equipment. [20679] Failed in access to the server. There are too many users accessing the server at this time. *After a brief moment, please try again. An exception due to incapability to retrieve Restart. If the same symptom recurs, parameters such as user/service settings. contact your service engineer. If the setting file is damaged, reinstall it.

20623 FFCustomMsgBox

20635 Error

An exception that occurs in communication with electric medical charts. The cause is probably the incapability to retrieve parameters such as user/service settings.

Restart. If the same symptom recurs, contact your service engineer. Verify the connection setting between electric medical charts and CR-IR 391CL. If the setting file is damaged, reinstall it.

20662 FFCustomMsgBox

Cannot be restored if already deleted. If A study of the same menu could not be registered when executing the DO function disabled, enable it, and the study can be due to the specified study has been registered. deleted or disabled. Error that infrequently occurs 1. Click the button again. 2. Restart the client application. 3. Restart the client PC. 4. Restart the server PC. 1. Click the button again. 2. Restart the client application. 3. Restart the client PC. 4. Restart the server PC. Install the said application. Or, if the device that is used are different for each use, make setting so that the button is not displayed. * The setting for display/hide the button is not for each device, but for each user. 1. Try again after a while. 2. Close the unused applications.

20663 FFCustomMsgBox

20664 FFCustomMsgBox

Error that infrequently occurs

20665 FFCustomMsgBox

An external application such as electrocardiogram viewer is not installed, or the installation directory path is different from the setting. A request is denied due to excessive access to the server device.

20679 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-127

Appx MT1-128
Event Event Source Description Causes Remedies Remarks
20700 FFCustomMsgBox [20700] Approaching the limit of Capacity of either StudyDB or PatientDB is Contact your customer service. the database file size. approaching to its limit. *You need to upgrade the database. >Because the system will become unable to operate, please contact your service engineer immediately. [20701] There is not enough hard Not enough hard disk space for the entire disk space required to operate the system. system. *You need to add a hard drive. >Because the system will become unable to operate, please contact your service engineer immediately. [20702] Initialization process failed. *Restart the server computer. >Contact your service engineer if the same symptom recurs even after it has been restarted. [20703] Failed in access to a network hard drive. *Please check the status of the power and network connections. >If the problem persists, please contact your service engineer for maintenance. [20704] Failed in processing the data transfer. *Please check the status of the power and network connections. >If the problem persists, please contact your service engineer for maintenance. Failure. Add a NAS.

20701 FFCustomMsgBox

20702 FFCustomMsgBox

Restart both the server application and the client application. If the problem still exists or the same symptom recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Confirm the network connection to the NAS and the power of the NAS.

20703 FFCustomMsgBox

Not connected to the NAS.

20704 FFCustomMsgBox

Not connected to the NAS. Or failure

Confirm the network connection to the NAS and the power of the NAS.

20705 FFCustomMsgBox

Not connected to the NAS. [20705] Failed in configuring a network drive and obtaining information. *Please check the power of a hard drive and network connections, and try again. [20706] Backup process failed. Not connected to the NAS. *Please check the power of a hard Or failure drive and network connections. >If the problem persists, please contact your service engineer for maintenance.

Confirm the network connection to the NAS and the power of the NAS.

20706 FFCustomMsgBox

Confirm the network connection to the NAS and the power of the NAS.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-128

Appx MT1-129
Event Event Source Description
[20707] A timeout occurred. *Restart the system and make a backup again. >If the problem persists, please contact your service engineer for maintenance. [20720] Failed in exporting database > Restart the system and try again. + If restarting does not resolve, contact your service engineer. [20721] Failed in importing database. > Check Error.log file in the selected folder and try again. [20724] Failed in importing database. > Restart the system and try again. + If restarting does not resolve, contact your service engineer. [20725] Failed in reading in CSV file. > Check the data and character string of the file and try again. [20727] Failed in obtaining information from database. > Restart the system and try again. + If restarting does not resolve, contact your service engineer. [20728] Failed in registering for database. > Restart the system and try again. + If restarting does not resolve, contact your service engineer. [20760] Failed in registering the study. *Restart the server computer. >Contact your service engineer if the same symptom recurs even after it has been restarted. Failure.

Causes

Remedies
Restart both the server application and the client application. If the problem still exists or the same symptom recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Just as the message states.

Remarks

20707 FFCustomMsgBox

20720 FFCustomMsgBox

Occurs when failed to importing the breed and species csv file.

Only for veterinary hospital.

20721 FFCustomMsgBox

Occurs when failed to importing the breed and species csv file. Occurs when failed to importing the breed and species csv file.

Just as the message states.

Only for veterinary hospital.

20724 FFCustomMsgBox

Just as the message states.

Only for veterinary hospital.

20725 FFCustomMsgBox

Occurs when failed to importing the breed and species csv file. Just as the message states.

Just as the message states.

Only for veterinary hospital.

20727 FFCustomMsgBox

Only for veterinary hospital.

20728 FFCustomMsgBox

Just as the message states.

Only for veterinary hospital.

20760 FFCustomMsgBox

This error is attributable to an inactive server application.

Restart the server computer and retry. Contact your service engineer if the same symptom recurs even after it has been restarted.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-129

Appx MT1-130
Event Event Source Description
[20785] Failed in initializing the list. *Restart the server computer. >Contact your service engineer if the same symptom recurs even after it has been restarted. [20786] Failed in initializing the list. *Restart the server computer. >Contact your service engineer if the same symptom recurs even after it has been restarted.

Causes
An exception might have occurred during the initialization process for the list.

Remedies
Just as the message states.

Remarks

20785 FFCustomMsgBox

20786 FFCustomMsgBox

An exception might have occurred during the study data retrieving process from the list.

Just as the message states.

20787 FFCustomMsgBox

[20787] Failed in updating the list. An exception might have occurred during the updating process after retrieving the *Please update the list again. >Contact your service engineer if study data from the list. the same symptom recurs even after it has been updated. [20788] Failed in updating the list. An exception might have occurred during the study data retrieving process from the *Please update the list again. >Contact your service engineer if list. the same symptom recurs even after it has been updated. [20789] Failed in updating the list. An exception might have occurred during the study data retrieving process from the *Please update the list again. >Contact your service engineer if list. the same symptom recurs even after it has been updated. [20790] Failed in starting up the Indicator. *Restart the server computer. >Contact your service engineer if the same symptom recurs even after it has been restarted. [20814] An error occurred while acquiring Patient information. > Check network cable for proper connection. > Ensure if the device runs properly in case it is connected to MWM device. * If the above does not resolve, contact your service engineer. An exception might have occurred during the initialization process for the indicator.

Just as the message states.

20788 FFCustomMsgBox

Just as the message states.

20789 FFCustomMsgBox

Just as the message states.

20790 FFCustomMsgBox

Just as the message states.

20814 FFCustomMsgBox

Occurs when failed in the communication with the DICOM MWM gateway.

Check the operation of the DICOM MWM gateway and the settings.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-130

Appx MT1-131
Event Event Source Description
[20815] An error occurred while acquiring Species information. > Restart the system and try again. + If restarting does not resolve, contact your service engineer. [20816] An error occurred while acquiring Breed information. > Restart the system and try again. + If restarting does not resolve, contact your service engineer. [20828] An error occurred in converting the unit of measure of body length. > Restart the system and try again. + If restarting does not resolve, contact your service engineer.

Causes
Just as the message states.

Remedies

Remarks
Only for veterinary hospital.

20815 FFCustomMsgBox

20816 FFCustomMsgBox

Just as the message states.

Only for veterinary hospital.

20828 FFCustomMsgBox

Just as the message states.

20829 FFCustomMsgBox

Does not occur normally. [20829] An error occurred while converting the unit of measure for Weight. > Restart the system and try again. + If restarting does not resolve, contact your service engineer. Failed in connecting to the image database.

Just as the message states.

21001 FFCustomMsgBox

The problem is attributable, for instance, to Check whether the SQL service manager an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted). The problem is attributable, for instance, to Check whether the SQL service manager an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted). The problem is attributable, for instance, to Check whether the SQL service manager an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted).

List

21002 FFCustomMsgBox

Initialization of the image database failed.

List

21003 FFCustomMsgBox

Failed in information acquisition from the image database.

List

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-131

Appx MT1-132
Event Event Source Description
Initialization of the image database failed.

Causes

Remedies
List

Remarks

21004 FFCustomMsgBox

The problem is attributable, for instance, to Check whether the SQL service manager an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted).

21005 FFCustomMsgBox

Failed in setting information to the The problem is attributable, for instance, to Check whether the SQL service manager image database. an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted). Failed in deleting the study information. The problem is attributable, for instance, to Check whether the SQL service manager an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted). Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

List

21006 FFCustomMsgBox

List

21007 FFCustomMsgBox 21008 FFCustomMsgBox 21009 FFCustomMsgBox 21010 FFCustomMsgBox 21011 FFCustomMsgBox

Failed in connecting to the system It is conceivable that the database file was setting database. damaged or deleted. Failed in accessing the system setting database. It is conceivable that the database file was damaged or deleted.

List List List List List List List List List List List List

Failed in information acquisition It is conceivable that the database file was from the system setting database. damaged or deleted. Failed in connecting to the character database. Failed in accessing the character string database. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

21012 FFCustomMsgBox 21013 FFCustomMsgBox 21014 FFCustomMsgBox 21015 FFCustomMsgBox 21016 FFCustomMsgBox 21017 FFCustomMsgBox 21018 FFCustomMsgBox

Failed in obtaining the information It is conceivable that the database file was from the character string damaged or deleted. database. Failed in accessing the definition file. Failed in opening the registry information. Failed in retrieving the registry information. Failed in writing the registry information. Failed in closing the registry information. Failed in receiving message.

It is conceivable that the file was damaged Restart. If the same symptom recurs, or deleted. perform a reinstallation. It is conceivable that the registry information was damaged or deleted. It is conceivable that the registry information was damaged or deleted. It is conceivable that the registry information was damaged or deleted. It is conceivable that the registry information was damaged or deleted. The system was unstable. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-132

Appx MT1-133
Event Event Source Description
Failed in canceling the output processing. Failed in output. Failed in receiving message. Failed in initializing process for message communication. Failed in terminating process for message communication.

Causes
The selected image was being output or already deleted. The selected image was being output or already deleted. The system was unstable. The system was unstable. The system was unstable.

Remedies
Nothing particular. Nothing particular. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Check the connected equipment or network. Check the connected equipment or network. Check the connected equipment or network. Check the connected equipment or network. Check the connected equipment or network. Check the connected equipment or network. Check the connected equipment or network. Nothing particular. Nothing particular. Nothing particular. Nothing particular. Nothing particular. Check the RIS side setup information and the like. List List List List List List List List List List List List List List List List List List List List

Remarks

21019 FFCustomMsgBox 21020 FFCustomMsgBox 21021 FFCustomMsgBox 21022 FFCustomMsgBox 21023 FFCustomMsgBox 21024 FFCustomMsgBox 21025 FFCustomMsgBox 21030 FFCustomMsgBox 21031 FFCustomMsgBox 21032 FFCustomMsgBox 21033 FFCustomMsgBox 21034 FFCustomMsgBox 21035 FFCustomMsgBox 21036 FFCustomMsgBox 21037 FFCustomMsgBox 21038 FFCustomMsgBox 21039 FFCustomMsgBox 21040 FFCustomMsgBox 21041 FFCustomMsgBox 21051 FFCustomMsgBox

Failed in acquiring the host setting It is conceivable that the database file was database. damaged or deleted. Failed in editing the host setting database. Failed in study start. Failed in QA start. Failed in study re-start. Failed in obtaining study information from host %s. Failed in locking the study. Failed in study completion processing. The target study exists but is not displayed on the list. The target study could not be found. The system was unstable. Connection equipment was not operative or the network was unstable. Connection equipment was not operative or the network was unstable. Connection equipment was not operative or the network was unstable. Connection equipment was not operative or the network was unstable. Connection equipment was not operative or the network was unstable. Connection equipment was not operative or the network was unstable. Connection equipment was not operative or the network was unstable. A specified study has already been deleted.

The input format for date is wrong. The input format was incorrect. The input format for time is wrong. The input format was incorrect. Searched word is illegal. Multiple target studies exist. The study cannot be started. Unidentified study has been received from RIS. The input word was incorrect. Two or more relevant studies existed. Illegal data was contained in the study information received from the RIS.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-133

Appx MT1-134
Event Event Source Description
There was no automatically deletable study data.

Causes

Remedies
Perform the following remedial actions: Check the contents of the study and then perform the determination procedure. Unlock unnecessary locked studies. Check the output queue and delete any unnecessary studies. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

21055 FFCustomMsgBox

21055 FFRoutine

ErrorCode:%1%nSubSystem:%2 Deletable study data was not found. %nSourceFile: %3%nSpotCode: %4%nThe Study data that can be deleted is not found. \nPlease confirm the study list.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

21056 FFCustomMsgBox

There was no automatically deletable image data.

Perform the following remedial actions: Check the contents of the study and then perform the determination procedure. Unlock unnecessary locked studies. Check the output queue and delete any unnecessary studies. Delete unnecessary files from the hard disk. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

21056 FFRoutine

ErrorCode:%1%nSubSystem:%2 Deletable image data was not found. %nSourceFile: %3%nSpotCode: %4%nThe Image data that can be deleted is not found. \nPlease confirm the study list.

21057 FFCustomMsgBox 21057 FFRoutine

There was no automatically deletable patient information. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe Patient data that can be deleted is not found. \nPlease confirm the study list. Deletable patient information was not found. The program might be faulty. Restart the server application and client %1= Error Code: The code that uniquely application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Start the User Utility and review the settings for automatically determining a physicians name.

21067 FFCustomMsgBox

An error occurred in settings for automatically determining a physicians name, which consequently skipped automatic determination processing.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-134

Appx MT1-135
Event Event Source Description Causes Remedies Remarks
21067 FFRoutine ErrorCode:%1%nSubSystem:%2 The automatic verification user was not %nSourceFile: %3%nSpotCode: set, or the setup information was %4%nVerify Doctor setting error. \ inconsistent. nPlease confirm the inspection list. With the Client Utility, review the setup %1= Error Code: The code that uniquely information about the automatic verification identifies an error. user. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

21101 21102 21103 21104 21105 21106 21129 21144

FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

An error of unknown cause occurred. Failed in obtaining the study information. It cant be designated as a source. It cant be designated as a source. The image couldnt be moved. The indication error of the study information occurred. ????? The hard disk is full. No backup copies have been made for a certain period of time. An error of unknown cause occurred. Failed in initialization processing. Radiographer information database is abnormal. Failed in obtaining the registry information. Failed in setting registry values. Failed in clearing a displayed image. Failed in connecting to the database. Failed in connecting to the database. Failed in setting the host sharing study information.

An error of unknown cause occurred. It is not possible to continue image transfer processing. A specified study has already been deleted.

The disk has no free space.

Delete unnecessary study information. In compliance with the on-screen instructions, specify whether or not to start the Backup Utility.

List

21201 FFCustomMsgBox 21202 FFCustomMsgBox 21203 FFCustomMsgBox 21204 FFCustomMsgBox 21205 FFCustomMsgBox 21206 FFCustomMsgBox 21207 FFCustomMsgBox 21208 FFCustomMsgBox 21209 FFCustomMsgBox

The system was unstable. The system was unstable. It is conceivable that the database file was damaged or deleted. The system was unstable. The system was unstable. The system was unstable. Connection equipment was not operative or the network was unstable. Connection equipment was not operative or the network was unstable. The system was unstable.

Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Check the connected equipment or network. Check the connected equipment or network. Restart. If the same symptom recurs, perform a reinstallation.

List List List List List List List List List

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-135

Appx MT1-136
Event
21211

Event Source
FFCustomMsgBox

Description
Failed in obtaining the study information from the database.

Causes
It is conceivable that the database file was damaged or deleted.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. If it is intended, click the OK button. If not, click the cancel button. If it is intended, click the OK button. If not, click the cancel button. Just as the message states. List List List List

Remarks

21210 FFCustomMsgBox

An error of unknown cause It is conceivable that the database file was occurred in obtaining radiographer damaged or deleted. information. An error of unknown cause occurred. An error of unknown cause occurred. Study information cannot be obtained. [21609] The current user will be logged off the system. +Are you sure? [21610] Application will be terminated. +Are you sure? The system was unstable. The system was unstable. The logoff button is clicked. The exit button is clicked.

21212 FFCustomMsgBox 21213 FFCustomMsgBox 21609 FFCustomMsgBox 21610 FFCustomMsgBox 21628 Warning

Displayed when an unexpected error [21628] An unexpected error occurs in the connection with the receipt occurred when trying to acquire computer. the patient information. *Ensure that the network cable has been connected correctly and retry. *If you are connected to the receipt computer, please check if the device is operating normally. > Contact our service engineer for maintenance if these steps do not resolve the issue. [20636] Communication with the EMR failed. *Confirm connection to the EMR device and retry. [21637] An error is received from the EMR. *Contact your service engineer. [21638] A fatal error occurred. *Contact your service engineer. [21640] An attempt to acquire information from the EMR failed. > Confirm connection to the electronic medical chart device and retry communication. Continue processing if no information is acquired from the electronic medical chart device. Occurs in case of abnormal parameter of the electronic medical chart connection. Occurs when the cable format for the communication with the electronic medical chart is abnormal. Occurs when the cable for the communication with the electronic medical chart cannot be analyzed. The prior connection with the electronic medical chart fails, or a trouble including a physical factor other than the mentioned above.

21636 Warning

Verify the communication settings between electronic medical chart and CR-IR 391CL. Verify the communication settings between electronic medical chart and CR-IR 391CL. Verify the communication settings between electronic medical chart and CR-IR 391CL. Verify the physical connection and the communication settings between electronic medical chart and CR-IR 391CL.

21637 Warning 21638 Warning 21640 Warning

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-136

Appx MT1-137
Event Event Source Description
[21660] Image reading operation is in process. *Please Complete or Suspend ongoing study, and retry again.

Causes
There is a study whose Take X-rays window is left open on the PC in-use.

Remedies
Finish or pause the exposure, and close the Take X-rays window. The DO function can only be executed for a study retrieved from an RU. However, even for a study retrieved from the RU, the DO function cannot be executed if it is deleted once, and then imported from a storage DVD. Just as the message states.

Remarks

21660 FFCustomMsgBox

21661 FFCustomMsgBox

[21661] An attempt to register new The DO function was executed for a study study failed. that had been retrieved from a disc or *This kind of study cannot be exposed with an external device. registered. [21666] Selected study cannot be displayed in Image Viewer.. *Please select the completed studies. [21737] Failed in editing operation. > Restart the system and try again. + If restarting does not resolve, contact your service engineer. [21811] A study is being performed. *Please Complete or Suspend ongoing study. >If the computer currently in use is unable to check, the study may be used by other user. >Otherwise, please restart all computers of this system. [21817] The body length contains illegal character. > Only single-byte numerical characters and period (.) are allowed for Body length. Enter again. [21818] The Weight contains illegal character. > Only single-byte numerical characters and period (.) are allowed for Weight. Enter again. The Image Viewer button is clicked while selecting a reserved study or a study that was being exposed. Just as the message states.

21666 FFCustomMsgBox

21737 FFCustomMsgBox

Only for veterinary hospital.

21811

FFCustomMsgBox

Just as the message states.

21817 FFCustomMsgBox

Just as the message states.

21818 FFCustomMsgBox

Just as the message states.

21819 FFCustomMsgBox

[21819] The Species contains Just as the message states. illegal character. > The characters below cannot be used for Breed. Enter again. #%&+?\*@

Only for veterinary hospital.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-137

Appx MT1-138
Event Event Source Description Causes Remedies Remarks
Only for veterinary hospital. 21820 FFCustomMsgBox [21820] The Breed contains illegal Just as the message states. character. > The characters below cannot be used for Species. Enter again. #%&+?\*@ [21821] The Responsible person Just as the message states. contains illegal character. > Any double-byte characters and the characters below cannot be used for Responsible person. Enter again. #%&+?\*@ Just as the message states. [21822] The Responsible organization contains illegal character. > The characters below cannot be used for Responsible organization. Enter again. #%&+?\*@ ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode:% 4%nSystem setting value acquisition error.\nThe default value is used. Values could not be acquired from the system setup database. The process will be continued by using default values for some settings. Check to ensure that the Service Utility settings are correct. If it does not help, perform a reinstallation.

21821 FFCustomMsgBox

Only for veterinary hospital.

21822 FFCustomMsgBox

Only for veterinary hospital.

22054 FFRoutine

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

22058 FFRoutine

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe processing failure was done by the Study DB capacity adjustment thread. \nHowever, the process continues.

An error occurred when an attempt was made to automatically delete study data. . For a detailed description of the cause of the error, refer to the FFDBCom event information.

Restart. If the same symptom recurs, perform a reinstallation.

22059 FFRoutine

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe processing failure was done by the HDD capacity adjustment thread. \nHowever, the process continues.

An error occurred when an attempt was made to automatically delete image data. For a detailed description of the cause of the error, refer to the FFDBCom event information.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-138

Appx MT1-139
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe processing failure was done by the Patient DB capacity adjustment thread. \nHowever, the process continues.

Causes
An error occurred when an attempt was made to automatically delete patient information. For a detailed description of the cause of the error, refer to the FFDBCom event information.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

22060 FFRoutine

22061 FFRoutine

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe processing failure was done by the Reference Images delete thread. \nHowever, the process continues.

An error occurred when an attempt was made to automatically delete a temporal/ stored image. For a detailed description of the cause of the error, refer to the FFDBCom event information.

Restart. If the same symptom recurs, perform a reinstallation.

22069 FFRoutine

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the output of the study. \nPlease confirm the inspection list.

The output completion notification was not successfully sent to the output section.

Restart. If the same symptom recurs, perform a reinstallation.

22103 FFMain

It failed in the acquisition of the configuration information. The initialization treatment cant be continued. /MainProcess:Main ()

The version information was not Reinstall the system. successfully acquired. It is conceivable that the Version.env file did not exist in the specified directory or that the contents of the file were damaged. Reinstall the system. (There is no operational problem. However, communication logs cannot be saved.) Start the SQL server and restart the server %1= Error Code: The code that uniquely application. identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

22128 FFMain 22142 FFMain

An error occurred in logfile backup A log file backup was not successfully treatment. made. It is conceivable that the specified /MainProcess:xxxxx pathname was incorrect. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe start processing in the MainProcess is continued though it failed in the restructuring of DB. Although an attempt to rebuild a database failed, the main process startup process is continued.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-139

Appx MT1-140
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nPlease back up at once.

Causes
Backup is overdue and not done.

Remedies
Use the Backup Utility to make a backup without undue delay.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

22145 FFMain

22150 FFMain

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nProcessing is continued though it failed in writing the operation log.

Although the operation log was not successfully written, the process will be continued.

Check for a free space on the disk.

22155 FFMain

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nProcessing is continued though it failed in writing event information.

Although the event information was not Restart. If the same symptom recurs, successfully written, processing continues. perform a reinstallation. The OS resource might be insufficient.

22156 FFMain

ErrorCode:%1%nSubSystem:%2 Failed in obtaining the version information. Restart. If the same symptom recurs, %nSourceFile: %3%nSpotCode: It is conceivable that the registry perform a reinstallation. %4%nIt failed in the acquisition of information was damaged. version information.%n Please reactivate server PC.

23050 FFRoutine

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nInformation

Information (the parameter information for Nothing particular. automatic deletion/automatic determination is recorded below).

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-140

Appx MT1-141
Event Event Source Description Causes Remedies Remarks
24368 FFCustomMsgBox [24368] Importing a study has Just as the message states. been completed. * When importing from other than a disk for storage, check the patient information, and set up the patient ID correctly. An Image display cannot be executed during operations. A display of the list cannot be executed during operations. A display cannot be cleared during operations. [24615] The study being imported A study that was being retrieved was tried has been selected. to be opened with the Image Viewer. Close the dialog and retry. Close the dialog and retry. Close the dialog and retry. Wait until the study is retrieved, and open it with the Image Viewer.

24408 FFCustomMsgBox 24409 FFCustomMsgBox 24410 FFCustomMsgBox 24615 Confirmation 24620 Confirmation 24621 FFCustomMsgBox 24624 FFCustomMsgBox 24625 FFCustomMsgBox

[24620] There is a study waiting to An additional exposure was instructed from Select an option. be started. an electronic medical chart while an +Do you want to start it? exposure. [24621] Patient information will be For confirmation. modified. +Are you sure? [24624] No Patient ID has been input. *Input the patient ID. [24625] Patient ID can not be changed. *Use the Client Utility to change the patient ID. For confirmation. For confirmation. Select an option. Just as the message states. Just as the message states.

24626 FFCustomMsgBox

[24626] No patients sex has been For confirmation. selected. *Please select the sex of a patient. [24627] The patient information of It was attempted to change the patient information while displaying the patient the receipt computer is given priority for being searched. information of the external system. *Please edit the information of the receipt computer. [24639] No patient information is currently active. [24726] No folder is selected. [24729] A part of information has not been registered. > Check the patient information that is not registered and register again. No active patient is in an electronic medical chart. Just as the message states. Occurs when failed in registering a part of the patient information.

Just as the message states.

24627 Confirmation

Just as the message states.

24639 Confirmation 24726 FFCustomMsgBox 24729 FFCustomMsgBox

Just as the message states.

Only for veterinary hospital.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-141

Appx MT1-142
Event Event Source Description
[24730] The name of species is too long. > Enter correct information. [24731] The name of breed is too long. > Enter correct information. [24732] The name of species remains blank. > Enter the name of breed. [24733] The name of breed remains blank. > Enter the name of species. [24734] The name of species contains invalid character. > Enter correct information. [24735] The name of breed contains invalid character. > Enter correct information.

Causes
Just as the message states. Just as the message states. Just as the message states. Just as the message states. Just as the message states. Just as the message states.

Remedies

Remarks
Only for veterinary hospital. Only for veterinary hospital. Only for veterinary hospital. Only for veterinary hospital. Only for veterinary hospital. Only for veterinary hospital. Only for veterinary hospital. Only for veterinary hospital. Only for veterinary hospital.

24730 FFCustomMsgBox 24731 FFCustomMsgBox 24732 FFCustomMsgBox 24733 FFCustomMsgBox 24734 FFCustomMsgBox 24735 FFCustomMsgBox 24736 FFCustomMsgBox 24738 FFCustomMsgBox 24739 FFCustomMsgBox

[24736] Duplicated value is found. Just as the message states. > Enter a non-duplicate value. [24738] The selected folder does not exist. > Select a folder and try again. [24739] No file exist in the selected folder. > Check the location and the name of the file and try again. [20740] Entered information will not be set. +Are you sure? Just as the message states. Just as the message states.

24740 FFCustomMsgBox 24741 FFCustomMsgBox 24767 FFCustomMsgBox 24768 FFCustomMsgBox

The cancel button is clicked in the Display setting window.

If it is intended, click the OK button. If not, click the cancel button.

[20741] Cannot be added because It was attempted to add items over its limit. Click the OK button to return to the Display the number of selected items has setting window, and delete existing items if already reached its limit. you want to add the items. [24767] Cannot be added because The number of selected menus has already Delete an selected item, and then select it. the number of selected menus reached its limit (20 items). has already reached its limit. [24768] Image reading operation is being conducted +Do you want to register the study? The Take X-rays window is started on the same PC or another client PC. Click the OK button to register the study and take X-rays later.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-142

Appx MT1-143
Event Event Source Description
[24769] Do you want to register the study?

Causes
Because Behavior on registering a study is set to Register only (not start).

Remedies
To register the study, click the OK button. Not to register the study, click the cancel button. * The setting needs to be changed to open the Take X-rays window when an exposure menu button is clicked. Select Customize from the utility menus, and open the Display setting window. In the Take X-rays window, select Register and start the study with the specified menu for Behavior on registering a study. Click the OK button.

Remarks

24769 FFCustomMsgBox

24770 FFCustomMsgBox 24813 FFCustomMsgBox

[24770] Successfully registered. [24813] Information on MWM device is being referred to first. > Edit the patient information on MWM device. [24831]The import of database is complete.

Registering the study has been successfully done.

Occurs when user attempted to change the Just as the message states. patient information that was retrieved and displayed from the DICOM MWM gateway. Just as the message states. Only for veterinary hospital. Only for veterinary hospital. Restart the server application and client %1= Error Code: The code that uniquely application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart the server application and client %1= Error Code: The code that uniquely application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

24831 FFCustomMsgBox 24832 FFCustomMsgBox 29051 FFRoutine

[24832] The export of database is Just as the message states. complete. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nSequence error of the message between processes. \nPlease reactivate server PC. A sequence error occurred during interprocess communication. The program might be faulty.

29052 FFRoutine

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nSend error of the message between processes. \nPlease reactivate server PC.

An inter-process message transmission error occurred. The program might be faulty.

29053 FFRoutine

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nParameter error of the message between processes. \nPlease reactivate server PC.

A parameter analysis error (internal system Restart. If the same symptom recurs, error) occurred during inter-process perform a reinstallation. communication.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-143

Appx MT1-144
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe parameter error occurred. \nPlease reactivate server PC.

Causes

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

29066 FFRoutine

A parameter abnormality was found Restart. If the same symptom recurs, between methods. An internal system error perform a reinstallation. occurred.

29071 FFRoutine

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred. \nPlease reactivate server PC.

An error of unknown cause occurred.

Restart both the server PC and client PC. If the same error recurs, perform a reinstallation.

29107 FFMain 29112 FFMain

It failed in the preparation of the pipe. The treatment cant be continued. /MainProcess:Main () It failed in the indication of the routine mode transition. /MainProcess:m_ProcessControl_ OnRunProcComplete () An unusual message was received. This message is ignored. /MainProcess:m_ ProcessComControl_ OnRecvNotification () An unusual send cause was received. This send cause is ignored. /MainProcess:m_Proce ssComControl_ OnRecvNotification () The form of the place of the transmission isnt right. /MainProcess:SendMessage ()

An attempt to create an inter-process communication pipe failed. The system might be unstable. The routine transition instruction message was not successfully issued. This error is attributable, for instance, to an inactive subprocess or a missing pipe.

Restart. Restart. If the same symptom recurs, perform a reinstallation.

29114

FFMain

Restart. If the same symptom recurs, The received message was unusual. It is conceivable that the message was not perform a reinstallation. registered in the message information database or that the system was unstable. A message was received from an unknown Restart. If the same symptom recurs, source. It is conceivable that the perform a reinstallation. transmission source was not registered in the message information database or that a wrong transmission source was selected. An unknown transmission destination was specified for the received message. It is conceivable that the transmission destination was not registered in the message information database or that a wrong transmission destination was selected. Restart. If the same symptom recurs, perform a reinstallation.

29115

FFMain

29116

FFMain

29117

FFMain

It failed in the message delivery. / MainProcess:SendMessage ()

A message delivery was not successful. Restart. If the same symptom recurs, It is conceivable that the subprocess at the perform a reinstallation. transmission destination was not running.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-144

Appx MT1-145
Event
29119

Event Source
FFMain

Description
It failed in the process completion notice. /MainProcess:ProcessEndAnswer Message () It failed in the unusual occurrence notice. /MainProcess: ErrorNoticeMessage () It failed in the pipe close. /MainProcess:EndMainProcess () It failed in close of the message data base. /MainProcess:xxxxx It failed in reading of the registry information. /MainProcess:xxxxx It failed in writing of the registry information. /MainProcess:xxxxx

Causes
A termination notification was not successfully issued to the subprocess. This error is attributable to an inactive subprocess or system instability. Restart.

Remedies

Remarks

29122 FFMain

An abnormality occurrence notification was Restart. not successfully issued to the subprocess. This error is attributable to an inactive subprocess or system instability. An attempt to close the inter-process communication pipe failed. The system might be unstable. The message database was not successfully closed. It is conceivable that the system was unstable. Data was not successfully acquired from the registry. This error is attributable to improper installation. Data was not successfully written into the registry. It is conceivable that the system was unstable. Restart. Restart. Reinstall the system. Restart. The program might be faulty. Check the operations performed before and after the error occurrence, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

29123 FFMain 29125 FFMain 29126 FFMain 29127 FFMain 29350 ThumbnailList

ErrorCode:%1%nSubSystem:%2 A program error occurred. %nSourceFile:%3%nSpotCode:% 4%nThe asynchronous download thread of the thumbnail image cannot be The asynchronous download thread of the thumbnail image cannot be correctly ended.

30001 FFCustomMsgBox 30002 FFCustomMsgBox 30003 FFCustomMsgBox 30004 FFCustomMsgBox 30005 FFCustomMsgBox 30013 FFCustomMsgBox

Failed in obtaining the connection It is conceivable that the file was damaged Restart. If the same symptom recurs, characters to the character or deleted. perform a reinstallation. database. Failed in connecting to the character database. It is conceivable that the database file was damaged or deleted. Restart. If the same symptom recurs, perform a reinstallation.

Failed in obtaining the connection It is conceivable that the file was damaged Restart. If the same symptom recurs, characters to the system setting or deleted. perform a reinstallation. database. Failed in connecting to the system It is conceivable that the database file was setting database. damaged or deleted. Restart. If the same symptom recurs, perform a reinstallation.

Failed in obtaining the connection It is conceivable that the file was damaged Restart. If the same symptom recurs, characters to the image database. or deleted. perform a reinstallation. Failed in saving the display setting It is conceivable that the registry of list (worklist). information was damaged or deleted. Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-145

Appx MT1-146
Event Event Source Description Causes Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

30019 FFCustomMsgBox 30027 FFCustomMsgBox 30045 FFCustomMsgBox 30057 FFCustomMsgBox 30085 FFCustomMsgBox 30100 FCRWeb

Failed in obtaining the connection It is conceivable that the database file was characters to the network setting damaged or deleted. database. Failed in list initialization (worklist). It is conceivable that the registry information was damaged or deleted. IP address on the Image Reader cannot be obtained. Failed in receiving message. It is conceivable that the database file was damaged or deleted. The system was unstable.

Failed in obtaining the connection It is conceivable that the file was damaged Restart. If the same symptom recurs, characters to the Image Reader or deleted. perform a reinstallation. status information database. ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Arbitrary Error Details. Check the connection to the receipt computer. Retransmit then the study from the receipt computer. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30101 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Arbitrary Error Details.

The current user does not have the privilege for performing this operation.

Log in as a user with operating privileges, and then retry.

30102 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Arbitrary Error Details.

Adequate sources for system operation were not available.

Restart the System.

30103 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Arbitrary Error Details.

A program error occurred.

The program might be faulty. Check the operations performed before and after the error occurrence, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-146

Appx MT1-147
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Arbitrary Error Details.

Causes
It is conceivable that the network can be unstable.

Remedies
Check the connected equipment or network.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30104 FCRWeb

30105 FFCustomMsgBox 30106 FFCustomMsgBox 30107 FFCustomMsgBox 30108 FFCustomMsgBox 30109 FFCustomMsgBox 30110 30111 30117 FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Failed in list initialization (waiting for study). Failed in list initialization (waiting for QA). Failed in list initialization (waiting for output). Failed in list initialization (already output). Failed in list initialization (all). Failed in list initialization (today). Failed in initializing the list (media). Failed in list refreshment (worklist).

The system was unstable. The system was unstable. The system was unstable. The system was unstable. The system was unstable. The system was unstable.

Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

The system was unstable.

Restart. If the same symptom recurs, perform a reinstallation.

30121 FFCustomMsgBox 30122 FFCustomMsgBox 30125 FFCustomMsgBox 30129 FFCustomMsgBox 30147 FFCustomMsgBox 30148 FFCustomMsgBox 30149 FFCustomMsgBox

Failed in obtaining the connection It is conceivable that the file was damaged Restart. If the same symptom recurs, characters to the Image Reader or deleted. perform a reinstallation. information database. Failed in accessing the Image Reader information database. It is conceivable that the database file was damaged or deleted. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Failed in obtaining the system It is conceivable that the database file was setting information (IP size series). damaged or deleted. Failed in obtaining the system setting information (Pantomography processing). It is conceivable that the database file was damaged or deleted.

Failed in obtaining the system It is conceivable that the database file was setting information (Magnetic card damaged or deleted. type). Failed in obtaining the system It is conceivable that the database file was setting information (Magnetic card damaged or deleted. type). Failed in obtaining the system setting information (Hospital card used). It is conceivable that the database file was damaged or deleted.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-147

Appx MT1-148
Event Event Source Description
Failed in obtaining information from database. Failed in initialization processing. Failed in obtaining the path information (image data folder). Failed in terminating process.

Causes
It is conceivable that the database file was damaged or deleted. The system was unstable.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

30150 FFCustomMsgBox 30151 FFCustomMsgBox 30152 FFCustomMsgBox 30153 FFCustomMsgBox 30155 FFCustomMsgBox 30157 FFCustomMsgBox 30200 FFCustomMsgBox 30201 FFCustomMsgBox 30202 FFCustomMsgBox 30203 FFCustomMsgBox 30204 FFCustomMsgBox 30205 FFCustomMsgBox 30206 FFCustomMsgBox 30207 FFCustomMsgBox 30300 FFInput

It is conceivable that the file was damaged Restart. If the same symptom recurs, or deleted. perform a reinstallation. The system was unstable. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Check the settings and then restart. If the same symptom recurs, perform a reinstallation. Check the settings and then restart. If the same symptom recurs, perform a reinstallation. Check the settings and then restart. If the same symptom recurs, perform a reinstallation.

Failed in obtaining the connection It is conceivable that the database file was characters to the database. damaged or deleted. Failed in accessing to database. Failed in RIS activation. A communication error with RIS occurred. A communication error with RIS occurred. Failed in study terminating process. The system cannot be started due Failed in installation. to improperly performed installation. Failed in search processing. Failed in initializing patient additional information. An error of unknown cause occurred with connection to the P.Console. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred. \nPlease reactivate server PC. An unknown error occurred during initialization process. The system was unstable. The system was unstable. It is conceivable that the database file was damaged or deleted. There may be a problem with the RIS module or RIS setup. There may be a problem with the RIS module or RIS setup. There may be a problem with the RIS module or RIS setup.

Reinstall the system. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Restart. If the same symptom recurs, perform a reinstallation.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30300 FFCustomMsgBox
020-221-02E 01.08.2010 FM5563

An error of unknown cause occurred.

CR-IR 391CL Service Manual

Appx MT1-148

Appx MT1-149
Event Event Source Description
Failed in obtaining information from the system setting database. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nSystem setting value acquisition error. \nThe default value is used. The value was not successfully acquired Restart. If the same symptom recurs, from the system setup database while an perform a reinstallation. initialization process was being performed. The database might be damaged. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

Causes

Remedies

Remarks

30301 FFCustomMsgBox 30301 FFInput

30302 FFCustomMsgBox

A failure occurred in an attempt to acquire values from the connection device setup database. It failed in the acquisition of a value from a connection device setting database. Value acquisition from the connected equipment setup database failed. The database might be damaged. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30302 FFInput

30303 FFCustomMsgBox 30303 FFInput

Failed in initialization processing. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nInitialization was discontinued: An internal control system error had occurred. A system setup value could not be acquired. The database might be damaged. Restart. If the same symptom recurs, perform a reinstallation.

30304 FFCustomMsgBox 30304 FFInput

Acquisition of path information failed. ErrorCode:%1%nSubSystem:%2 A Directory.ini file access error occurred. %nSourceFile: %3%nSpotCode: The file might be damaged. %4%nIt failed in the acquisition of file path information. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30305 FFCustomMsgBox

Failed in terminating process.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-149

Appx MT1-150
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe termination failed: Because of internal control or execute release of area.

Causes
The termination process failed due, for instance, to an internal control termination process failure or an area deallocation failure.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30305 FFInput

30306 FFCustomMsgBox 30306 FFInput

An attempt to create an image information file resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nImage information file (DDO) detected damage while executing the image input process. A damaged image information file (DDO) was found while the image input process was being performed. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30307 FFCustomMsgBox 30307 FFInput

An attempt to register image information onto the database resulted in a failure. ErrorCode:%1%nSubSystem:%2 Image information was not successfully Restart. If the same symptom recurs, %nSourceFile: %3%nSpotCode: registered in the database while the image perform a reinstallation. %4%nIt failed in the registration of input process was being performed. the image information to the database while the image-input processing %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30308 FFCustomMsgBox 30309 FFCustomMsgBox

Image acquisition failed. Termination processing failed.

This event will not be displayed. Retry after checking the Image Reader status. Termination cannot be executed when a cassette is being inserted into the Image Reader. A certain error occurred on the Hobbit side during the interval between the creation and transmission of the patient information to be transmitted to the RU. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

30310 FFInput

Patient information transmission failure

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-150

Appx MT1-151
Event
30311

Event Source
FFInput

Description

Causes

Remedies

Remarks

Patient information display failure. After patient information was transmitted to Restart the image reader. If the same error the RU, an error occurred on the RU side recurs, perform a reinstallation. If the for some reason. reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nSystem Error. An unknown error occurred during initialization process. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30500 FCRWeb

30500 FFCustomMsgBox 30501 FFCustomMsgBox

An unknown error occurred. [30501] Failed in gaining access Just as the message states. to the server computer. Timeout occurred while processing. > Check the connections to the network and hub. > Press the button below to close the dialog, and then restart the same study from Refer tab page. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred while initializing it. Please reboot Server-computer. An unknown error occurred during an initialization process.

Restart the server computer.

30502 FCRWeb

Restart. If the same symptom recurs, perform a reinstallation.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30502 FFCustomMsgBox 30503 FCRWeb

An unknown error occurred during initialization processing. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the acquisition of the reservation inspection. The reserved study was not successfully acquired. This failure is attributable to an inactive database or an internal system error.

Restart the server computer. Restart both the server PC and client PC. If the same error recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30503 FFCustomMsgBox

An attempt to acquire reserved studies resulted in a failure.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-151

Appx MT1-152
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the deletion of the reservation inspection.

Causes
The reserved study was not successfully deleted. This failure is attributable to an inactive database or an internal system error.

Remedies
Restart both the server PC and client PC. If the same error recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30504 FCRWeb

30504 FFCustomMsgBox 30505 FCRWeb

An attempt to delete reserved studies resulted in a failure. ErrorCode:%1%nSubSystem:%2 Study acquisition failed. This failure is %nSourceFile: %3%nSpotCode: attributable to an inactive database or an %4%nIt failed in the acquisition of internal system error. inspection information.

Restart the server computer. Restart both the server PC and client PC. If the same error recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30505 FFCustomMsgBox 30506 FCRWeb

An attempt to acquire studies resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the retrieval of patient information. Can not get patient-info from database. The patient information search process failed. This failure is attributable to an inactive database or an internal system error.

Restart the server computer. Restart both the server PC and client PC. If the same error recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30506 FFCustomMsgBox 30507 FCRWeb

Failed in searching the patient information. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the information acquisition from the Ekarte The information could not be acquired from an electronic medical chart. This error is attributable to an incorrect setting in the Service Utility or an unconnected network.

Restart the server computer. With the Service Utility, check the electronic medical chart settings. If the settings are correct, check the network cable, hub, and other network devices. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30507 FFCustomMsgBox

An attempt to acquire information from the EMR resulted in a failure.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-152

Appx MT1-153
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the acquisition of device information.

Causes
The output destination equipment information was not successfully acquired. This failure is attributable to an inactive database or an internal system error.

Remedies
Restart both the server PC and client PC. If the same error recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30508 FCRWeb

30508 FFCustomMsgBox 30509 FCRWeb

A failure occurred in an attempt to acquire information of devices targeted for image output. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred while processing the attestation. An exception occurred during an authentication process. This is an internal system error.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30509 FFCustomMsgBox 30510 FCRWeb

An unknown error occurred during authentication processing. ErrorCode:%1%nSubSystem:%2 Study registration failed. This failure is %nSourceFile: %3%nSpotCode: attributable to an inactive database or an %4%nIt failed in the registration of internal system error. the inspection.

Restart the server computer. Restart both the server PC and client PC. If the same error recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30510 FFCustomMsgBox 30511 FCRWeb

Study registration resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the communication with the server. The communication with the server was not successfully established. It is conceivable that the server PC is not running or does not exist in the network.

Restart the server computer. Restart both the server PC and client PC. If the same error recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30511

FFCustomMsgBox

Communication with the server computer resulted in a failure

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-153

Appx MT1-154
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in beginning of the inspection.

Causes

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30512 FCRWeb

The study start process was not Restart. If the same symptom recurs, successfully performed. An internal system perform a reinstallation. error occurred.

30512 FFCustomMsgBox 30513 FCRWeb

Study start processing failed. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the end of the inspection.

Restart the server computer. The study termination process was not Restart. If the same symptom recurs, successfully performed. An internal system perform a reinstallation. error occurred.

30513 FFCustomMsgBox 30514 FCRWeb

Study termination processing failed. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the update processing of the image.

Restart the server computer. The image update process was not Restart. If the same symptom recurs, successfully performed. This error is perform a reinstallation. attributable to a damaged database, a broken DDO, or a disconnected server PC. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30514 FFCustomMsgBox 30515 FCRWeb

Image update processing failed. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in information in the image acquisition. Image information was not successfully acquired. This error is attributable to a damaged database, a broken DDO, or a disconnected server PC.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation.

30515 FFCustomMsgBox

An attempt to acquire image information resulted in a failure.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-154

Appx MT1-155
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred in the exclusive operation.

Causes
An unknown error occurred during an exclusive process.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30516 FCRWeb

30516 FFCustomMsgBox 30517 FCRWeb

An unknown error occurred during exclusive processing. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the update processing of the menu addition. An update process for menu addition was not successfully performed. An internal system error occurred.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30517 FFCustomMsgBox 30518 FCRWeb

Update of added menus resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the update processing of the menu change. An update process for menu addition was not successfully performed. An internal system error occurred.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30518 FFCustomMsgBox 30519 FCRWeb

Update of added menus resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the update processing of the menu deletion. An update process for menu deletion/ image invalidation was not successfully performed. An internal system error occurred.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30519 FFCustomMsgBox

A failure occurred in an attempt to update menu deletion/image inactivation.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-155

Appx MT1-156
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the update processing of the menu array substitution.

Causes
The update process for a display order change was not successfully performed. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30520 FCRWeb

30520 FFCustomMsgBox 30521 FCRWeb

A failure occurred in an attempt to store order of displaying equipment users in a list. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the update processing of the image replacement.

Restart the server computer. The update process for image replacement Restart. If the same symptom recurs, was not successfully performed. An internal perform a reinstallation. system error occurred. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30521 FFCustomMsgBox 30522 FCRWeb

A failure occurred in an attempt to update replaced images. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the update processing of the setting in the output destination. The output destination setting was not successfully updated. An internal system error occurred.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30522 FFCustomMsgBox 30523 FCRWeb

A failure occurred in an attempt to update settings for target destination of image output. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the update processing of patient ID.

Restart the server computer. The patient ID update process was not Restart. If the same symptom recurs, successfully performed. An internal system perform a reinstallation. error occurred. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30523 FFCustomMsgBox

A failure occurred in an attempt to update patient ID.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-156

Appx MT1-157
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the update processing of patient information.

Causes
The update process for detailed patient information was not successfully performed. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30524 FCRWeb

30524 FFCustomMsgBox 30525 FCRWeb

A failure occurred in an attempt to update patients detailed information. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the information acquisition. Can not get information from NetConfib.mdb. The NetConfig value was not successfully acquired. An internal system error occurred.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30525 FFCustomMsgBox 30526 FCRWeb

Acquisition of equipment information failed. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the information acquisition. Can not get information from MenuDataBase. Menu information was not successfully acquired. An internal system error occurred.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30526 FFCustomMsgBox 30527 FFCustomMsgBox 30528 FFCustomMsgBox 30529 FFCustomMsgBox 30530 FFCustomMsgBox

Acquisition of menu information failed. An attempt to acquire study output status resulted in a failure. An attempt to acquire equipment output status resulted in a failure. A failure occurred in an attempt to update menu deletion/image inactivation. A failure occurred in an attempt to update menu deletion/image inactivation.

Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-157

Appx MT1-158
Event Event Source Description
A failure occurred in an attempt to update menu deletion/image inactivation. A failure occurred in an attempt to update menu deletion/image inactivation. A failure occurred in an attempt to update menu deletion/image inactivation. An unknown error occurred during initialization processing. An unknown error occurred during initialization processing. An unknown error occurred during initialization processing. A failure occurred in an attempt to update patients detailed information. A failure occurred in an attempt to update patients detailed information. A failure occurred in an attempt to update patients detailed information. A failure occurred in an attempt to update patients detailed information. A failure occurred in an attempt to update patients detailed information. A failure occurred in an attempt to update patients detailed information. A failure occurred in an attempt to update patients detailed information. A failure occurred in an attempt to update patients detailed information. A failure occurred in an attempt to update patients detailed information.

Causes

Remedies
Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

Remarks

30531 FFCustomMsgBox 30532 FFCustomMsgBox 30533 FFCustomMsgBox 30534 FFCustomMsgBox 30535 FFCustomMsgBox 30536 FFCustomMsgBox 30537 FFCustomMsgBox 30538 FFCustomMsgBox 30539 FFCustomMsgBox 30540 FFCustomMsgBox 30541 FFCustomMsgBox 30542 FFCustomMsgBox 30543 FFCustomMsgBox 30544 FFCustomMsgBox 30545 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-158

Appx MT1-159
Event Event Source Description
A failure occurred in an attempt to update patients detailed information. A failure occurred in an attempt to update patients detailed information. A failure occurred in an attempt to update patients detailed information. A failure occurred in an attempt to update patients detailed information. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred. An unknown error occurred during initialization process.

Causes

Remedies
Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

30546 FFCustomMsgBox 30547 FFCustomMsgBox 30548 FFCustomMsgBox 30549 FFCustomMsgBox 30550 FFCrExamCom

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30550 FFCustomMsgBox 30551 FFCrExamCom

An unknown error occurred during initialization processing. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe parameter error occurred. An illegal parameter was specified.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30551 FFCustomMsgBox 30552 FFCrExamCom

An unknown error occurred during initialization processing. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while DB Component was executing it. An unknown error occurred while a database component was being executed.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30552 FFCustomMsgBox

An unknown error occurred during initialization processing.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-159

Appx MT1-160
Event Event Source Description
ErrorCode:%1%nSubSystem: %2%nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while StatusManagement Component was executing it.

Causes

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30553 FFCrExamCom

An unknown error occurred while the study Restart. If the same symptom recurs, status change component was being perform a reinstallation. executed.

30553 FFCustomMsgBox 30554 FFCrExamCom

An unknown error occurred during initialization processing. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while CRExam Component was executing it.

Restart the server computer. An unknown error occurred when an Restart. If the same symptom recurs, attempt was made to execute a component perform a reinstallation. of a CR study. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30554 FFCustomMsgBox 30555 FFCrExamCom

A failure occurred in an attempt to update patient ID. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while ImageGeneration Component was executing it. An unknown error occurred while the processed image generation component was being executed.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30555 FFCustomMsgBox 30556 FFCustomMsgBox 30557 FFCustomMsgBox 30558 FFCustomMsgBox 30559 FFCustomMsgBox 30560 FFCustomMsgBox 30561 FFCustomMsgBox

A failure occurred in an attempt to update patient ID. A failure occurred in an attempt to update patient ID. A failure occurred in an attempt to update patient ID. A failure occurred in an attempt to update patient ID. A failure occurred in an attempt to update patient ID. A failure occurred in an attempt to update patient ID. A failure occurred in an attempt to update patient ID.

Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-160

Appx MT1-161
Event Event Source Description
A failure occurred in an attempt to update patient ID. A failure occurred in an attempt to update patient ID. A failure occurred in an attempt to update patient ID. A failure occurred in an attempt to update patient ID. A failure occurred in an attempt to update patient ID. An unknown error occurred during initialization processing. An unknown error occurred during initialization processing. An unknown error occurred during initialization processing. An unknown error occurred during initialization processing. An unknown error occurred during initialization processing. An unknown error occurred during initialization process. An attempt to acquire information from the EMR resulted in a failure. An attempt to acquire information from the EMR resulted in a failure. An attempt to acquire information from the EMR resulted in a failure. An attempt to acquire information from the EMR resulted in a failure. An attempt to acquire information from the EMR resulted in a failure. An attempt to acquire information from the EMR resulted in a failure. An attempt to acquire information from the EMR resulted in a failure. An unknown error occurred during exclusive processing. An unknown error occurred during exclusive processing.

Causes

Remedies
Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

Remarks

30562 FFCustomMsgBox 30563 FFCustomMsgBox 30564 FFCustomMsgBox 30565 FFCustomMsgBox 30566 FFCustomMsgBox 30567 FFCustomMsgBox 30568 FFCustomMsgBox 30569 FFCustomMsgBox 30570 FFCustomMsgBox 30571 FFCustomMsgBox 30572 FFCustomMsgBox 30573 FFCustomMsgBox 30574 FFCustomMsgBox 30575 FFCustomMsgBox 30576 FFCustomMsgBox 30577 FFCustomMsgBox 30578 FFCustomMsgBox 30579 FFCustomMsgBox 30580 FFCustomMsgBox 30581 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-161

Appx MT1-162
Event Event Source Description
An unknown error occurred during exclusive processing. An unknown error occurred during exclusive processing. An unknown error occurred during exclusive processing. An unknown error occurred during exclusive processing. An unknown error occurred during exclusive processing. An unknown error occurred during exclusive processing. An unknown error occurred during exclusive processing. An unknown error occurred during exclusive processing. An unknown error occurred during exclusive processing. An unknown error occurred during exclusive processing. An unknown error occurred during exclusive processing. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process.

Causes

Remedies
Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

Remarks

30582 FFCustomMsgBox 30583 FFCustomMsgBox 30584 FFCustomMsgBox 30585 FFCustomMsgBox 30586 FFCustomMsgBox 30587 FFCustomMsgBox 30588 FFCustomMsgBox 30589 FFCustomMsgBox 30590 FFCustomMsgBox 30591 FFCustomMsgBox 30592 FFCustomMsgBox 30593 FFCustomMsgBox 30594 FFCustomMsgBox 30595 FFCustomMsgBox 30596 FFCustomMsgBox 30597 FFCustomMsgBox 30598 FFCustomMsgBox 30599 FFCustomMsgBox 30600 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-162

Appx MT1-163
Event Event Source Description
ErrorCode:%1%nSubSystem: %2%nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred.

Causes
An unknown error occurred during initialization process.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30600 FFEntryAddCom

30601 FFCustomMsgBox 30601 FFEntryAddCom

An unknown error occurred during initialization process. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe parameter error occurred. An illegal parameter was specified.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30602 FFCustomMsgBox 30602 FFEntryAddCom

A failure occurred in an attempt to update settings for target destination of image output. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while InitialProc was executing it. An unknown error occurred during an initialization process.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30603 FFCustomMsgBox 30603 FFEntryAddCom

A failure occurred in an attempt to update settings for target destination of image output. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while acquiring Menu information. An unknown error occurred when an attempt was made to acquire menu information. The database might be damaged.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30604 FFCustomMsgBox

A failure occurred in an attempt to update settings for target destination of image output.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-163

Appx MT1-164
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while setting patient profile.

Causes
An unknown error occurred during patient information setup. The database might be damaged.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30604 FFEntryAddCom

30605 FFCustomMsgBox 30605 FFEntryAddCom

A failure occurred in an attempt to update settings for target destination of image output. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while information at the output destination. An unknown error occurred when an attempt was made to set the output destination information. The database might be damaged.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30606 FFCustomMsgBox 30606 FFEntryAddCom

A failure occurred in an attempt to update settings for target destination of image output. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while setting Menu Information. An unknown error occurred when an attempt was made to acquire menu information. The database might be damaged.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30607 FFCustomMsgBox 30607 FFEntryAddCom

A failure occurred in an attempt to update settings for target destination of image output. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while setting registered Study information. An unknown error occurred when an attempt was made to set up registered study information. The database might be damaged.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30608 FFCustomMsgBox

A failure occurred in an attempt to update settings for target destination of image output.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-164

Appx MT1-165
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred by the generation of the Study sequence number.

Causes
An unknown error occurred when an attempt was made to issue an image sequence number.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30608 FFEntryAddCom

30609 FFCustomMsgBox 30609 FFEntryAddCom

A failure occurred in an attempt to update settings for target destination of image output. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred by the generation of the Image sequence number. An unknown error occurred when an attempt was made to issue an image sequence number.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30610 FFCustomMsgBox 30610 FFEntryAddCom

A failure occurred in an attempt to update settings for target destination of image output. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred by setting the value to DDO. An error occurred when an attempt was made to set a DDO value. An internal system error occurred.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30611 30611

FFCustomMsgBox FFEntryAddCom

A failure occurred in an attempt to update settings for target destination of image output. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while Study Information was registering. An unknown error occurred when an attempt was made to register study information in a database.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30612 FFCustomMsgBox

An unknown error occurred during initialization process.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-165

Appx MT1-166
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while Image Information was registering.

Causes
An unknown error occurred when an attempt was made to register image information in a database.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30612 FFEntryAddCom

30613 FFCustomMsgBox 30614 FFCustomMsgBox 30615 FFCustomMsgBox 30616 FFCustomMsgBox 30617 FFCustomMsgBox 30618 FFCustomMsgBox 30619 FFCustomMsgBox 30620 FFCustomMsgBox 30621 FFCustomMsgBox 30622 FFCustomMsgBox 30623 FFCustomMsgBox 30624 FFCustomMsgBox 30625 FFCustomMsgBox 30626 FFCustomMsgBox 30627 FFCustomMsgBox 30628 FFCustomMsgBox
020-221-02E 01.08.2010 FM5563

A failure occurred in an attempt to acquire information of target destination for image output. A failure occurred in an attempt to acquire information of target destination for image output. An unknown error occurred during initialization process. An unknown error occurred during initialization process. Update of added menus resulted in a failure. Update of added menus resulted in a failure. Update of added menus resulted in a failure. Update of added menus resulted in a failure. Update of added menus resulted in a failure. Update of added menus resulted in a failure. Update of added menus resulted in a failure. Update of added menus resulted in a failure. Update of added menus resulted in a failure. An unknown error occurred during initialization process. An unknown error occurred during initialization process. Update of added menus resulted in a failure.

Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

CR-IR 391CL Service Manual

Appx MT1-166

Appx MT1-167
Event Event Source Description
Update of added menus resulted in a failure. Update of added menus resulted in a failure. Update of added menus resulted in a failure. Update of added menus resulted in a failure. Update of added menus resulted in a failure. Update of added menus resulted in a failure. Update of added menus resulted in a failure. Update of added menus resulted in a failure. An unknown error occurred during initialization process. Study registration resulted in a failure. Study registration resulted in a failure. Study registration resulted in a failure. Study registration resulted in a failure. Study registration resulted in a failure. Study registration resulted in a failure. Study registration resulted in a failure. Study registration resulted in a failure. Study registration resulted in a failure. Study registration resulted in a failure. Study registration resulted in a failure.

Causes

Remedies
Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

Remarks

30629 FFCustomMsgBox 30630 FFCustomMsgBox 30631 FFCustomMsgBox 30632 FFCustomMsgBox 30633 FFCustomMsgBox 30634 FFCustomMsgBox 30635 FFCustomMsgBox 30636 FFCustomMsgBox 30637 FFCustomMsgBox 30638 FFCustomMsgBox 30639 FFCustomMsgBox 30640 FFCustomMsgBox 30641 FFCustomMsgBox 30642 FFCustomMsgBox 30643 FFCustomMsgBox 30644 FFCustomMsgBox 30645 FFCustomMsgBox 30646 FFCustomMsgBox 30647 FFCustomMsgBox 30648 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-167

Appx MT1-168
Event Event Source Description
Study registration resulted in a failure. Study registration resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred. An unknown error occurred during initialization process.

Causes

Remedies
Restart the server computer. Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

30649 FFCustomMsgBox 30650 FFCustomMsgBox 30650 FFDelInvalidCom

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30651 FFCustomMsgBox 30651 FFDelInvalidCom

Study registration resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAn illegal parameter was specified. An illegal parameter was specified.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30652 FFCustomMsgBox 30652 FFDelInvalidCom

Study registration resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred in initialization. An unknown error occurred during an initialization process.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30653 FFCustomMsgBox 30653 FFDelInvalidCom

Study registration resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while acquiring Study information from DB. An unknown error occurred when an attempt was made to acquire study information from a database.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-168

Appx MT1-169
Event Event Source Description
Study registration resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred by loading the DDO file. An error occurred when an attempt was made to load a DDO file. The error is attributable to a damaged DDO file or OS resource insufficiency.

Causes

Remedies
Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30654 FFCustomMsgBox 30654 FFDelInvalidCom

30655 FFCustomMsgBox 30655 FFDelInvalidCom

Study registration resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred by setting the value to DDO. An error occurred when an attempt was made to set a DDO value. The error is attributable to OS resource insufficiency.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30656 FFCustomMsgBox 30656 FFDelInvalidCom

An attempt to delete reserved studies resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while executing processing of Re-Imageing. An unknown error occurred during a re-exposure process.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30657 FFCustomMsgBox 30657 FFDelInvalidCom

An attempt to delete reserved studies resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while registering the Image information to DB. An unknown error occurred when an attempt was made to register image information in a database.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30658 FFCustomMsgBox

An attempt to delete reserved studies resulted in a failure.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-169

Appx MT1-170
Event Event Source Description Causes Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30658 FFDelInvalidCom

ErrorCode:%1%nSubSystem:%2 An unknown error occurred when an %nSourceFile: %3%nSpotCode: attempt was made to delete image %4%nThe unknown error information from a database. occurred while deleting the Image information to DB.

30659 FFCustomMsgBox 30660 FFCustomMsgBox 30661 FFCustomMsgBox 30662 FFCustomMsgBox 30663 FFCustomMsgBox 30664 FFCustomMsgBox 30665 FFCustomMsgBox 30666 FFCustomMsgBox 30667 FFCustomMsgBox 30668 FFCustomMsgBox 30669 FFCustomMsgBox 30670 FFCustomMsgBox 30671 FFCustomMsgBox 30672 FFCustomMsgBox 30673 FFCustomMsgBox 30674 FFCustomMsgBox

An attempt to delete reserved studies resulted in a failure. An attempt to delete reserved studies resulted in a failure. An attempt to delete reserved studies resulted in a failure. An attempt to delete reserved studies resulted in a failure. An attempt to acquire reserved studies resulted in a failure. An attempt to acquire reserved studies resulted in a failure. An attempt to acquire reserved studies resulted in a failure. An unknown error occurred during initialization process. Failed in searching the patient information. Failed in searching the patient information. Failed in searching the patient information. Failed in searching the patient information. Failed in searching the patient information. Failed in searching the patient information. Failed in searching the patient information. Failed in searching the patient information.

Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-170

Appx MT1-171
Event Event Source Description
Failed in searching the patient information. Failed in searching the patient information. Failed in searching the patient information. Failed in searching the patient information. Failed in searching the patient information. An unknown error occurred during initialization process. A failure occurred in an attempt to store order of displaying equipment users in a list. A failure occurred in an attempt to store order of displaying equipment users in a list. A failure occurred in an attempt to store order of displaying equipment users in a list. A failure occurred in an attempt to store order of displaying equipment users in a list. A failure occurred in an attempt to store order of displaying equipment users in a list. A failure occurred in an attempt to store order of displaying equipment users in a list. A failure occurred in an attempt to store order of displaying equipment users in a list. A failure occurred in an attempt to store order of displaying equipment users in a list. A failure occurred in an attempt to store order of displaying equipment users in a list. An unknown error occurred during initialization process.

Causes

Remedies
Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

Remarks

30675 FFCustomMsgBox 30676 FFCustomMsgBox 30677 FFCustomMsgBox 30678 FFCustomMsgBox 30679 FFCustomMsgBox 30680 FFCustomMsgBox 30681 FFCustomMsgBox 30682 FFCustomMsgBox 30683 FFCustomMsgBox 30684 FFCustomMsgBox 30685 FFCustomMsgBox 30686 FFCustomMsgBox 30687 FFCustomMsgBox 30688 FFCustomMsgBox 30689 FFCustomMsgBox 30690 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-171

Appx MT1-172
Event Event Source Description
An unknown error occurred during initialization process. Communication with the server computer resulted in a failure Communication with the server computer resulted in a failure Communication with the server computer resulted in a failure Communication with the server computer resulted in a failure Communication with the server computer resulted in a failure Communication with the server computer resulted in a failure Communication with the server computer resulted in a failure Communication with the server computer resulted in a failure Study start processing failed. An unknown error occurred during initialization process.

Causes

Remedies
Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

30691 FFCustomMsgBox 30692 FFCustomMsgBox 30693 FFCustomMsgBox 30694 FFCustomMsgBox 30695 FFCustomMsgBox 30696 FFCustomMsgBox 30697 FFCustomMsgBox 30698 FFCustomMsgBox 30699 FFCustomMsgBox 30700 FFCustomMsgBox

30700 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30701 FFCustomMsgBox

Study start processing failed. An illegal parameter was specified.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation.

30701 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAn illegal parameter was specified.

30702 FFCustomMsgBox

Study start processing failed.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-172

Appx MT1-173
Event Event Source Description Causes
An unknown error occurred during an initialization process.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30702 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred in initialization.

30703 FFCustomMsgBox

Study start processing failed. An unknown error occurred when an attempt was made to acquire study information from a database.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation.

30703 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while acquiring Study information from the data base.

30704 FFCustomMsgBox

Study start processing failed. An error occurred when an attempt was made to load a DDO file. An internal system error occurred.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation.

30704 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred by loading the DDO file.

30705 FFCustomMsgBox

Study start processing failed. An error occurred when an attempt was made to set a DDO value. An internal system error occurred.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation.

30705 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred by setting the value to DDO.

30706 FFCustomMsgBox

Study start processing failed.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-173

Appx MT1-174
Event Event Source Description Causes
An unknown error occurred when a switch was being made to an unexposed exposure menu.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30706 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred about the untaking a picture while processing the change to the taking a picture menu. 30707 FFCustomMsgBox Study termination processing failed.

Restart the server computer. An unknown error occurred when the process for switching to the exposure menu for exposed images was being performed. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30707 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while processing the change to the picture menu that had been taken a picture.

30708 FFCustomMsgBox

Study termination processing failed. An unknown error occurred when an attempt was made to register image information in the database.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30708 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown occurred while registering the Image information to the data base.

30709 FFCustomMsgBox

Study termination processing failed. An unknown error occurred when an attempt was made to acquire menu information.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30709 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while acquiring Menu information.

30710 FFCustomMsgBox

Study termination processing failed.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-174

Appx MT1-175
Event Event Source Description Causes
An unknown error occurred during image file generation.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30710 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while generating the picture file.

30711

FFCustomMsgBox

Study termination processing failed. Study termination processing failed. Study termination processing failed. Study termination processing failed. Study termination processing failed. Study termination processing failed. Study termination processing failed. Study termination processing failed. Study termination processing failed. Study termination processing failed. Study termination processing failed. Study termination processing failed. Study termination processing failed. Study termination processing failed. Image update processing failed. Image update processing failed. Image update processing failed.

Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

30712 FFCustomMsgBox 30713 FFCustomMsgBox 30714 FFCustomMsgBox 30715 FFCustomMsgBox 30716 FFCustomMsgBox 30717 FFCustomMsgBox 30718 FFCustomMsgBox 30719 FFCustomMsgBox 30720 FFCustomMsgBox 30721 FFCustomMsgBox 30722 FFCustomMsgBox 30723 FFCustomMsgBox 30724 FFCustomMsgBox 30725 FFCustomMsgBox 30726 FFCustomMsgBox 30727 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-175

Appx MT1-176
Event Event Source Description
Image update processing failed. Image update processing failed. Image update processing failed. Image update processing failed. Image update processing failed. Image update processing failed. Image update processing failed. An unknown error occurred during initialization process. An attempt to acquire image information resulted in a failure. An attempt to acquire image information resulted in a failure. An attempt to acquire image information resulted in a failure. An attempt to acquire image information resulted in a failure. An attempt to acquire image information resulted in a failure. An attempt to acquire image information resulted in a failure. An attempt to acquire image information resulted in a failure. An attempt to acquire image information resulted in a failure. An attempt to acquire image information resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure.

Causes

Remedies
Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

Remarks

30728 FFCustomMsgBox 30729 FFCustomMsgBox 30730 FFCustomMsgBox 30731 FFCustomMsgBox 30732 FFCustomMsgBox 30733 FFCustomMsgBox 30734 FFCustomMsgBox 30735 FFCustomMsgBox 30736 FFCustomMsgBox 30737 FFCustomMsgBox 30738 FFCustomMsgBox 30739 FFCustomMsgBox 30740 FFCustomMsgBox 30741 FFCustomMsgBox 30742 FFCustomMsgBox 30743 FFCustomMsgBox 30744 FFCustomMsgBox 30745 FFCustomMsgBox 30746 FFCustomMsgBox 30747 FFCustomMsgBox 30748 FFCustomMsgBox 30749 FFCustomMsgBox 30750 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-176

Appx MT1-177
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred.

Causes
An unknown error occurred during initialization process.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30750 FFImageSwapCom

30751 FFCustomMsgBox 30751 FFImageSwapCom

An attempt to acquire studies resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAn illegal parameter was specified. An illegal parameter was specified.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30752 FFCustomMsgBox 30752 FFImageSwapCom

An attempt to acquire studies resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred in initialization. An unknown error occurred during an initialization process.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30753 FFImageSwapCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while acquiring Study information from the data base.

An unknown error occurred when an attempt was made to acquire study information from a database.

Restart. If the same symptom recurs, perform a reinstallation.

30753 FFCustomMsgBox

An attempt to acquire studies resulted in a failure.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-177

Appx MT1-178
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred by loading the DDO file.

Causes
An error occurred when an attempt was made to load a DDO file. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30754 FFImageSwapCom

30754 FFCustomMsgBox 30755 FFImageSwapCom

An attempt to acquire studies resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred by setting the value to DDO. An error occurred when an attempt was made to set a DDO value. An internal system error occurred.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30755 FFCustomMsgBox 30756 FFImageSwapCom

An attempt to acquire studies resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred while acquiring the replacement information data. An error occurred when an attempt was made to acquire replacement information data. This is an internal system error.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30756 FFCustomMsgBox 30757 FFImageSwapCom

An attempt to acquire studies resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown occurred while registering the Image information to the data base. An unknown error occurred when an attempt was made to register image information in the database.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30757 FFCustomMsgBox

An attempt to acquire studies resulted in a failure.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-178

Appx MT1-179
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while acquiring Menu information.

Causes
An unknown error occurred when an attempt was made to acquire menu information.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30758 FFImageSwapCom

30758 FFCustomMsgBox 30759 FFImageSwapCom

An attempt to acquire studies resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred while generating the picture file. An unknown error occurred during image file generation.

Restart the server computer. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

30759 FFCustomMsgBox 30760 FFCustomMsgBox 30761 FFCustomMsgBox 30762 FFCustomMsgBox 30763 FFCustomMsgBox 30764 FFCustomMsgBox 30765 FFCustomMsgBox 30766 FFCustomMsgBox 30767 FFCustomMsgBox 30768 FFCustomMsgBox 30769 FFCustomMsgBox 30770 FFCustomMsgBox

An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure. An attempt to acquire studies resulted in a failure.

Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-179

Appx MT1-180
Event Event Source Description
An attempt to acquire studies resulted in a failure. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process.

Causes

Remedies
Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

Remarks

30771 FFCustomMsgBox 30772 FFCustomMsgBox 30773 FFCustomMsgBox 30774 FFCustomMsgBox 30775 FFCustomMsgBox 30776 FFCustomMsgBox 30777 FFCustomMsgBox 30778 FFCustomMsgBox 30779 FFCustomMsgBox 30780 FFCustomMsgBox 30781 FFCustomMsgBox 30782 FFCustomMsgBox 30783 FFCustomMsgBox 30784 FFCustomMsgBox 30785 FFCustomMsgBox 30786 FFCustomMsgBox 30787 FFCustomMsgBox 30788 FFCustomMsgBox 30789 FFCustomMsgBox 30790 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-180

Appx MT1-181
Event Event Source Description
An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process. An unknown error occurred during initialization process.

Causes

Remedies
Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer. Restart the server computer.

Remarks

30791 FFCustomMsgBox 30792 FFCustomMsgBox 30793 FFCustomMsgBox 30794 FFCustomMsgBox 30795 FFCustomMsgBox 30796 FFCustomMsgBox 30797 FFCustomMsgBox 30798 FFCustomMsgBox 30799 FFCustomMsgBox 30800 FFCustomMsgBox 30801 FFCustomMsgBox 30802 FFCustomMsgBox 30803 FFCustomMsgBox 30804 FFCustomMsgBox 30805 FFCustomMsgBox 30806 FFCustomMsgBox

[30806] Failed in obtaining patient Occurs when failed in retrieving the patient Check the operation of the DICOM MWM information from the DICOM MWM gateway and the settings. information. gateway. > Restart the system and try again. + If restarting does not resolve, contact your service engineer. An unknown error has occurred. An unknown error has occurred. The system was unstable. Restart. If the same symptom recurs, perform a reinstallation. Press [Cancel] and finish trimming function. + To continue other processing, press the button below.

30850 FFCustomMsgBox 30851 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-181

Appx MT1-182
Event Event Source Description
The server device could not be accessed. Failed in obtaining the registry information (font name). Failed in obtaining the registry information (font size). Failed in obtaining the registry information (multi-byte language information). Failed in obtaining the used language in system setting. It is conceivable that the registry information was damaged or deleted. It is conceivable that the registry information was damaged or deleted. It is conceivable that the registry information was damaged or deleted. It is conceivable that the database file was damaged or deleted.

Causes

Remedies
Close the displayed message and try login again. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

30907 FFCustomMsgBox 31001 FFCustomMsgBox 31002 FFCustomMsgBox 31003 FFCustomMsgBox 31004 FFCustomMsgBox 31005 FFCustomMsgBox 31006 FFCustomMsgBox 31007 FFCustomMsgBox 31008 FFCustomMsgBox 31010 FFCustomMsgBox

Failed in obtaining the connection It is conceivable that the database file was characters to the character damaged or deleted. database. Failed in connecting to the character database. It is conceivable that the database file was damaged or deleted.

Failed in obtaining the connection It is conceivable that the database file was characters to the system setting damaged or deleted. database. Failed in connecting to the system It is conceivable that the database file was setting database. damaged or deleted. Failed in connecting to the image database.

The problem is attributable, for instance, to Check whether the SQL service manager an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted). The problem is attributable, for instance, to Check whether the SQL service manager an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted). The problem is attributable, for instance, to Check whether the SQL service manager an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted).

31011

FFCustomMsgBox

Failed in information acquisition from the image database.

31012 FFCustomMsgBox

Initialization of the image database failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-182

Appx MT1-183
Event Event Source Description
Failed in information acquisition from the image database.

Causes

Remedies

Remarks

31013 FFCustomMsgBox

The problem is attributable, for instance, to Check whether the SQL service manager an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted).

31014 FFCustomMsgBox

Failed in setting information to the The problem is attributable, for instance, to Check whether the SQL service manager image database. an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted). Failed in deleting information from The problem is attributable, for instance, to Check whether the SQL service manager the image database. an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted). Failed in connecting to the flag database. The problem is attributable, for instance, to Check whether the SQL service manager an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted). The problem is attributable, for instance, to Check whether the SQL service manager an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted).

31015 FFCustomMsgBox

31016 FFCustomMsgBox

31017 FFCustomMsgBox

Failed in accessing the flag database.

31018 FFCustomMsgBox

Failed in setting information to the The problem is attributable, for instance, to Check whether the SQL service manager flag database. an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted). Failed in initialization process for menu setting database. It is conceivable that the database file was damaged or deleted. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

31019 FFCustomMsgBox 31020 FFCustomMsgBox 31021 FFCustomMsgBox 31022 FFCustomMsgBox

Failed in obtaining the menu It is conceivable that the database file was information from the menu setting damaged or deleted. database. Failed in obtaining the menu parameter information from the menu setting database. Failed in terminating the menu setting database. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-183

Appx MT1-184
Event Event Source Description Causes Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom frequently occurs, replace the disk. Restart. If the same symptom frequently occurs, replace the disk. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

31023 FFCustomMsgBox 31024 FFCustomMsgBox 31025 FFCustomMsgBox 31026 FFCustomMsgBox 31027 FFCustomMsgBox 31028 FFCustomMsgBox 31029 FFCustomMsgBox 31030 FFCustomMsgBox 31031 FFCustomMsgBox 31032 FFCustomMsgBox 31033 FFCustomMsgBox 31034 FFCustomMsgBox 31035 FFCustomMsgBox 31036 FFCustomMsgBox 31037 FFCustomMsgBox 31038 FFCustomMsgBox 31039 FFCustomMsgBox 31040 FFCustomMsgBox

Failed in obtaining the connection It is conceivable that the database file was characters to the network setting damaged or deleted. database. Failed in connecting to the network setting database. Failed in obtaining information from the network setting database. Failed in issuing the image information. Failed in obtaining the image information. Failed in setting the image information. Failed in deleting the image information. Failed in reading the image information file. Failed in writing the image information file. Failed in releasing the image information. Failed in obtaining the caption information (Patient ID). Failed in obtaining the caption information (Accession No.). Failed in obtaining the caption information (Accession No.). It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. The system was unstable. The system was unstable. The system was unstable. The system was unstable. An image-related file was not successfully accessed. The problem is attributable to a disk. An image-related file was not successfully accessed. The problem is attributable to a disk. The system was unstable. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

Failed in obtaining the caption It is conceivable that the database file was information (Kanji-patients name). damaged or deleted. Failed in obtaining the caption information (sex). Failed in obtaining the caption information (sex: M). Failed in obtaining the caption information (sex: F). Failed in obtaining the caption information (sex: O). It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-184

Appx MT1-185
Event Event Source Description
Failed in obtaining the caption information (date of birth). Failed in obtaining the system setting information (Patient ID input character limitation).

Causes
It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Re-input correctly. Re-input correctly. Re-input correctly. Re-input correctly. Re-input correctly. Re-input correctly. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

31041 FFCustomMsgBox 31042 FFCustomMsgBox 31043 FFCustomMsgBox 31044 FFCustomMsgBox 31045 FFCustomMsgBox 31047 FFCustomMsgBox 31051 FFCustomMsgBox 31052 FFCustomMsgBox 31053 FFCustomMsgBox 31054 FFCustomMsgBox 31055 FFCustomMsgBox 31056 FFCustomMsgBox 31057 FFCustomMsgBox 31058 FFCustomMsgBox 31059 FFCustomMsgBox 31060 FFCustomMsgBox 31061 FFCustomMsgBox

Failed in obtaining the system It is conceivable that the database file was setting information (Accession No. damaged or deleted. input character limitation). Failed in obtaining the system setting information (Patient ID pudding format). It is conceivable that the database file was damaged or deleted.

Failed in obtaining the system It is conceivable that the database file was setting information (Accession No. damaged or deleted. pudding format). Failed in obtaining the system setting information (date of birth format). Patient ID includes invalid characters. Accession No. includes invalid characters. Patient Name includes invalid characters. Kanji-patient name includes invalid characters. Sex includes invalid characters. The input format for date of birth is invalid. It is conceivable that the database file was damaged or deleted. A 2-byte character, @, or other unacceptable character was contained. A 2-byte character, @, or other unacceptable character was contained. A 2-byte character, @, or other unacceptable character was contained. A 1-byte character or other unacceptable character was contained. A character other than M, F, and O was contained. The entry did not agree with a preselected birth date format.

Failed in accessing the requesting It is conceivable that the database file was department database. damaged or deleted. Failed in obtaining the caption information (requesting dep.). Failed in obtaining the item information for displaying in the requesting dep. Selection list. Failed in obtaining the requesting department information. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

Failed in obtaining the connection It is conceivable that the file was damaged Restart. If the same symptom recurs, characters to the requesting or deleted. perform a reinstallation. department database.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-185

Appx MT1-186
Event Event Source Description
Failed in obtaining the caption information (technologist). Failed in obtaining the item information for displaying in the technologist selection list.

Causes
It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Enter at least the patients sex. Restart. If the same symptom recurs, perform a reinstallation. Start an examination process with one examination item selected. Select an item prior to execution.

Remarks

31062 FFCustomMsgBox 31063 FFCustomMsgBox 31064 FFCustomMsgBox 31065 FFCustomMsgBox 31066 FFCustomMsgBox 31067 FFCustomMsgBox 31068 FFCustomMsgBox 31069 FFCustomMsgBox

Failed in accessing the It is conceivable that the database file was technologist information database. damaged or deleted.

Failed in obtaining the technologist It is conceivable that the database file was information. damaged or deleted. Failed in obtaining the connection It is conceivable that the database file was characters to the technologist damaged or deleted. database. Failed in obtaining the registry information (window size). No patient information is input. Failed in obtaining the system setting information (succeeded from exposure menu reservation list). Multiple studies cannot be executed. No list is selected. Film annotation includes invalid characters. Failed in obtaining information from the flag database. It is conceivable that the registry information was damaged or deleted. Nothing was entered in the patient information input field. It is conceivable that the database file was damaged or deleted. An attempt was made to start an examination process with more than one examination item selected from an examination waiting list. An attempt was made to start execution with no examination item selected.

31070 FFCustomMsgBox

31071 FFCustomMsgBox 31072 FFCustomMsgBox 31074 FFCustomMsgBox

An unacceptable character was contained. Re-input correctly. The problem is attributable, for instance, to Check whether the SQL service manager an inactive SQL service manager or is normally operating. If the symptom uninitialized image database. occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted). It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

31076 FFCustomMsgBox 31077 FFCustomMsgBox 31078 FFCustomMsgBox 31079 FFCustomMsgBox

Failed in obtaining the button image (Clear button). Failed in obtaining the button image (OK button). Failed in obtaining the button image (Cancel button). Failed in obtaining the button image (increment button).

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-186

Appx MT1-187
Event Event Source Description
Failed in obtaining the button image (decrement button). Failed in obtaining the button image (Next page button). Failed in obtaining the button image (previous page button). Failed in obtaining the caption information (woklist tab). Failed in obtaining caption information (media tab). Failed in updating the list (media). Failed in saving settings for the list (media) display. No study UID can be obtained from the list (media). Failed in obtaining the information It is conceivable that the database file was damaged or deleted. from the character string database. An error of unknown cause occurred. Failed in display processing by the image input subsystem. Failed in obtaining the path information (log saving folder). Failed in setting patient information. Failed in terminating the image input subsystem. Failed in terminating the image input subsystem. Failed in image inputting process in the image input sub-system. Failed in image inputting process in the image input sub-system. Failed in image inputting process in the image input sub-system. Failed in calling up the exposure menu. Failed in study terminating process. It is highly probable that the program was faulty. It is conceivable that the image data or image information file was damaged. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Causes
It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

31080 FFCustomMsgBox 31081 FFCustomMsgBox 31082 FFCustomMsgBox 31090 FFCustomMsgBox 31091 FFCustomMsgBox 31092 FFCustomMsgBox 31093 FFCustomMsgBox 31094 FFCustomMsgBox 31097 FFCustomMsgBox 31099 FFCustomMsgBox 31100 31101 31103 31105 31106 31107 31108 31109 31110 31111 FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

It is conceivable that the file was damaged Restart. If the same symptom recurs, or deleted. perform a reinstallation. The system was unstable. The system was unstable. The system was unstable. The system was unstable. The system was unstable. The system was unstable. The system was unstable. The system was unstable. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-187

Appx MT1-188
Event
31112 31113 31114 31116 31117 31118 31119 31120 31121 31122 31123 31124 31125 31126 31127 31128 31129

Event Source
FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Description

Causes

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

Failed in image inputting process. The system was unstable. Failed in image inputting process. The system was unstable. Failed in specifying the urgent processing. The system was unstable.

Communication line for monitoring It is highly probable that the RU or line was Check the RU and line. the connection status with the faulty. Image Reader (%s) has broken. No connection monitoring response from the Image Reader (%s). Control line with the Image Reader (%s) has broken. No command response from the Image Reader (%s). Failed in Image Reader status control. It is highly probable that the RU or line was Check the RU and line. faulty. It is highly probable that the RU or line was Check the RU and line. faulty. It is highly probable that the RU or line was Check the RU and line. faulty. It is highly probable that the RU or line was Check the RU and line. faulty.

Command requested to the Image It is highly probable that the RU or line was Check the RU and line. Reader has not been executed. faulty. Failed in obtaining the information It is highly probable that the RU or line was Check the RU and line. (status) from the Image Reader. faulty. Failed in obtaining the information It is highly probable that the RU or line was Check the RU and line. faulty. (machine code) from the Image Reader. Failed in obtaining the information It is highly probable that the RU or line was Check the RU and line. (FRUP version) from the Image faulty. Reader. Failed in re-connecting with the Image Reader. It is highly probable that the RU or line was Check the RU and line. faulty.

Failed in breaking connection with It is highly probable that the RU or line was Check the RU and line. the Image Reader. faulty. Failed in obtaining the caption information (Study with QA completed). Failed in obtaining the caption (only exposure completed). Failed in obtaining the caption information (Study interrupt button). It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-188

Appx MT1-189
Event
31130 31131 31132 31133 31134 31135 31136 31137 31138 31139 31140 31141 31142 31143 31144 31145 31146 31147 31148

Event Source
FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Description
Failed in obtaining the caption information (Cancel button). Failed in obtaining the caption information (Study reception tab).

Causes
It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

Failed in obtaining the caption It is conceivable that the database file was information (waiting for study tab). damaged or deleted. Failed in obtaining the caption information (waiting for QA tab). Failed in obtaining the caption information (Waiting for output tab). Failed in obtaining the caption information (Already output tab). Failed in obtaining the caption information (All tabs). Failed in obtaining the caption information (Today tab). Failed in obtaining the button image (System button). Failed in obtaining the caption information (Study reservation button). Failed in obtaining the caption information (Study list setting button). Patient information entered is illegal. Failed in obtaining the display group data. Failed in obtaining the display group data. Failed in obtaining the display group data. Failed in obtaining the display group data. Failed in obtaining the display group data. Failed in obtaining the display group data. Failed in obtaining the display group data. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

An unacceptable character was contained. Re-input correctly. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-189

Appx MT1-190
Event
31149 31152 31153 31154 31155 31158 31159 31160 31161 31162 31163 31164 31165 31166 31167 31168 31169 31170 31171 31172

Event Source
FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Description
Failed in obtaining the display group data. Failed in obtaining the exposure menu information. Failed in obtaining the button image (Urgent button). Failed in obtaining the button image (Study completed button). Failed in obtaining the button image (Update button). Failed in obtaining the button image (New button). Failed in obtaining the button image (Auto print control button). Failed in obtaining the button image (Re-shoot button). Failed in obtaining the button image (Add button). Failed in obtaining the button image (Delete button). Failed in obtaining the button image (Before scroll button). Failed in obtaining the button image (After Scroll button).

Causes
It is conceivable that the database file was damaged or deleted. The system was unstable. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

Failed in obtaining the system It is conceivable that the bitmap file was setting information (Series issuing damaged or deleted. type). Failed in obtaining the button image (QA button). Failed in obtaining the button image (Change button). Failed in obtaining the cassette insertion disabled image. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted.

Failed in obtaining the image icon It is conceivable that the bitmap file was (Mis-exposure). damaged or deleted. Failed in obtaining the button image (Image style button). Failed in obtaining the button image (No. of output film button). Failed in obtaining the tool tip (New button). It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-190

Appx MT1-191
Event
31173 31174 31175 31176 31177 31178 31179 31180 31181 31182 31183 31184 31185 31186 31187 31188 31189

Event Source
FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Description
Failed in obtaining the tool tip (Auto print control button).

Causes
It is conceivable that the database file was damaged or deleted.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

Failed in obtaining the tool tip (Re- It is conceivable that the database file was shoot button). damaged or deleted. Failed in obtaining the tool tip (Add It is conceivable that the database file was button). damaged or deleted. Failed in obtaining the tool tip (Delete button). Failed in obtaining the tool tip (Before scroll button). Failed in obtaining the tool tip (After scroll button). Failed in obtaining the tool tip (Monitor mode button). It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

Failed in obtaining the tool tip (QA It is conceivable that the database file was button). damaged or deleted. Failed in obtaining the tool tip (Change button). Failed in obtaining the tool tip (Rotation/Inversion button). Failed in obtaining the tool tip (EDR mode button). Failed in obtaining the tool tip (Image format button). It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

Failed in obtaining the tool tip It is conceivable that the database file was (Change menu parameter button). damaged or deleted. Failed in obtaining the registry information (Set No.). Failed in setting the registry information (Set No.). Failed in obtaining the system setting information (System ID). Failed in obtaining the system setting information (Autodistribution instruction information). It is conceivable that the registry information was damaged or deleted. It is conceivable that the registry information was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

31191 31192

FFCustomMsgBox FFCustomMsgBox

Failed in obtaining the system It is conceivable that the database file was setting information (Selector auto- damaged or deleted. switchover information). Failed in obtaining the system setting information (Menu autosequence information). It is conceivable that the database file was damaged or deleted.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-191

Appx MT1-192
Event
31193 31194 31196 31197 31198

Event Source
FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Description
Failed in obtaining the system setting information (Set No. minimum value information). Failed in obtaining the system setting information (Set No. maximum value information). Failed in obtaining the system setting information (Series information issuing method). No matching work ID exists. Failed in distribution process.

Causes
It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

The contents of the image file did not agree Perform Initialization of image database. with those of the image database. The system was unstable. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

31202 FFCustomMsgBox 31203 FFCustomMsgBox 31207 FFCustomMsgBox 31208 FFCustomMsgBox 31210 FFCustomMsgBox

Failed in obtaining the system It is conceivable that the database file was setting information (Patient damaged or deleted. information online serial port No.). Failed in obtaining the system setting information (Patient information online device name.). It is conceivable that the database file was damaged or deleted.

Failed in setting the Image Reader The system was unstable. machine code. Failed in obtaining the button image (New button). Failed in obtaining the system setting information (Image rotation/inversion selectable range). Failed in obtaining the button image (frontal image button). Failed in obtaining the button image (Left-right invert button). Failed in obtaining the button image (Upside-down invert button). Failed in obtaining the button image (180 degree rotation button). It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted.

31211

FFCustomMsgBox

31212 FFCustomMsgBox 31213 FFCustomMsgBox 31214 FFCustomMsgBox 31215 FFCustomMsgBox 31218 FFCustomMsgBox

Failed in obtaining the button It is conceivable that the bitmap file was image (90 degree rotation button). damaged or deleted. Failed in obtaining the system setting information (Image format selectable range). It is conceivable that the database file was damaged or deleted.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-192

Appx MT1-193
Event Event Source Description
Failed in obtaining the button image (SINGLE button). Failed in obtaining the button image (TWIN button).

Causes
It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

31219 FFCustomMsgBox 31220 FFCustomMsgBox 31225 FFCustomMsgBox 31226 FFCustomMsgBox 31227 FFCustomMsgBox 31232 FFCustomMsgBox 31235 FFCustomMsgBox 31236 FFCustomMsgBox 31241 FFCustomMsgBox 31242 FFCustomMsgBox 31243 FFCustomMsgBox 31244 FFCustomMsgBox 31245 FFCustomMsgBox 31246 FFCustomMsgBox 31247 FFCustomMsgBox 31248 FFCustomMsgBox

Failed in obtaining the connection It is conceivable that the file was damaged Restart. If the same symptom recurs, characters to the film annotation or deleted. perform a reinstallation. database. Failed in connecting characters to It is conceivable that the database file was the film annotation database. damaged or deleted. Failed in obtaining information It is conceivable that the database file was from the film annotation database. damaged or deleted. Failed in obtaining the system It is conceivable that the database file was setting information (Maximum No. damaged or deleted. of output film). Failed in obtaining the caption information (CS). Failed in obtaining the caption information (SS). It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required.

Failed in making thumbnail The system was unstable. images in image input subsystem. Failed in processing in image input subsystem. The system was unstable.

Image format information is illegal. A value in the image file conflicted with a system setting. Annotation information is illegal. No. of output film information is illegal. Distribution code information is illegal. A value in the image file conflicted with a system setting. A value in the image file conflicted with a system setting. A value in the image file conflicted with a system setting.

Image reading sensitivity is illegal. A value in the image file conflicted with a system setting. Average output density is illegal. A value in the image file conflicted with a system setting.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-193

Appx MT1-194
Event Event Source Description
EDR mode is illegal. Image filing mode is illegal. Function mode is illegal. IP logical size information is illegal. Contrast shift is illegal. The sensitivity shift information is illegal. There is a discrepancy between system setting and image information. There is a discrepancy between system setting and image information. There is a discrepancy between system setting and image information. There is a discrepancy between system setting and image information. Failed in obtaining the image invert/rotate information. Failed in obtaining the image format information. Failed in obtaining the image format information. Film annotation is illegal. Failed in obtaining the caption information (FIX).

Causes
A value in the image file conflicted with a system setting. A value in the image file conflicted with a system setting. A value in the image file conflicted with a system setting. A value in the image file conflicted with a system setting. A value in the image file conflicted with a system setting. A value in the image file conflicted with a system setting. A value in the image file conflicted with a system setting. A value in the image file conflicted with a system setting. A value in the image file conflicted with a system setting. A value in the image file conflicted with a system setting.

Remedies
Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required. Since a standard setting will be used as a substitute to continue with the process, no particular response is required.

Remarks

31249 FFCustomMsgBox 31250 FFCustomMsgBox 31251 FFCustomMsgBox 31252 FFCustomMsgBox 31253 FFCustomMsgBox 31254 FFCustomMsgBox 31255 FFCustomMsgBox 31256 FFCustomMsgBox 31257 FFCustomMsgBox 31258 FFCustomMsgBox 31259 FFCustomMsgBox 31260 FFCustomMsgBox 31261 FFCustomMsgBox 31262 FFCustomMsgBox 31265 FFCustomMsgBox

It is conceivable that the image information Delete the associated examination. If the was damaged. same symptom recurs after deletion, perform a reinstallation. A value in the image file conflicted with a system setting. Since a standard setting will be used as a substitute to continue with the process, no particular response is required.

It is conceivable that the image information Delete the associated examination. If the was damaged. same symptom recurs after deletion, perform a reinstallation. The registered film mark contained an unacceptable character. It is conceivable that the database file was damaged or deleted. With the User Utility, correct the film mark settings as needed. Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-194

Appx MT1-195
Event Event Source Description
Failed in obtaining the caption information (S value). Failed in obtaining the caption information (SEMI-X). Failed in obtaining the caption information (Density Average). Failed in obtaining the system setting information (EDR mode selectable range). Input value is illegal. Failed in obtaining the system setting information (Function selectable range). Failed in setting the function information. Failed in setting the No. of output film.

Causes
It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

31266 FFCustomMsgBox 31267 FFCustomMsgBox 31268 FFCustomMsgBox 31269 FFCustomMsgBox 31270 FFCustomMsgBox 31272 FFCustomMsgBox 31273 FFCustomMsgBox 31274 FFCustomMsgBox 31277 FFCustomMsgBox 31278 FFCustomMsgBox 31279 FFCustomMsgBox 31280 FFCustomMsgBox 31281 FFCustomMsgBox 31282 FFCustomMsgBox 31284 FFCustomMsgBox 31285 FFCustomMsgBox 31288 FFCustomMsgBox 31290 FFCustomMsgBox

The entered value contained an Make a proper entry. unacceptable character or was out of range or otherwise abnormal. It is conceivable that the database file was damaged or deleted. The system was unstable. The system was unstable. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Failed in setting the contrast shift. The system was unstable. Failed in setting the sensitivity shift. Failed in setting the EDR mode information. Failed in setting the FIX mode S value. The system was unstable. The system was unstable. The system was unstable.

Failed in setting the SEMI-X mode The system was unstable. average output density. Failed in QA starting process. Failed in obtaining the system setting information (Filing mode selectable range). Failed in setting the image filing information. The system was unstable. It is conceivable that the database file was damaged or deleted. The system was unstable.

Failed in obtaining the distribution The system was unstable. destination information. Failed in obtaining IP logical size information. The system was unstable.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-195

Appx MT1-196
Event Event Source Description
Failed in obtaining the system setting information (Distribution code change). Failed in obtaining the system setting information (Film annotation change). Failed in obtaining the system setting information (Function change). Failed in terminating process. Failed in terminating process. Failed in updating the list display. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred.\nPlease reactivate server PC.

Causes
It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. The system was unstable. The system was unstable. The system was unstable. An unknown error occurred during initialization process.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

31291 FFCustomMsgBox 31292 FFCustomMsgBox 31293 FFCustomMsgBox 31294 FFCustomMsgBox 31295 FFCustomMsgBox 31296 FFCustomMsgBox 31300 FFInput

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

31300 FFCustomMsgBox 31303 FFCustomMsgBox 31304 FFCustomMsgBox 31305 FFCustomMsgBox 31306 FFCustomMsgBox 31307 FFCustomMsgBox 31308 FFCustomMsgBox 31309 FFCustomMsgBox 31310 FFCustomMsgBox

An error of unknown cause occurred. Failed in obtaining study instance UID from list (Waiting for study). Failed in obtaining study instance UID from list (Waiting for QA). Failed in obtaining study instance UID from list (Waiting for output). Failed in obtaining study instance UID from list (Already output). Failed in obtaining study instance UID from list (All). Failed in obtaining study instance UID from list (Today). It is highly probable that the program was faulty. It is highly probable that the program was faulty. It is highly probable that the program was faulty. It is highly probable that the program was faulty. It is highly probable that the program was faulty. It is highly probable that the program was faulty. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Failed in updating the list (Waiting The system was unstable. for study) display. Failed in updating the list (Waiting The system was unstable. for QA) display.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-196

Appx MT1-197
Event
31311

Event Source
FFCustomMsgBox

Description

Causes

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Select only one study and execute. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

Failed in updating the list (Waiting The system was unstable. for output) display. Failed in updating the list (Already The system was unstable. output) display. Failed in updating the list (All) display. Failed in updating the list (Today) display. No. of selected studies is illegal. Study cannot be started. Failed in study starting process. No. of selected studies is illegal. QA cannot be started. Failed in QA starting process. Failed in QA starting process. Failed in obtaining the system setting information (Operational mode after studying). Failed in obtaining the button image (Utility button). Failed in obtaining the patient information. The system was unstable. The system was unstable. It is highly probable that the program was faulty. The system was unstable. It is highly probable that the program was faulty. The system was unstable. The system was unstable. It is conceivable that the database file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. The system was unstable.

31312 FFCustomMsgBox 31313 FFCustomMsgBox 31314 FFCustomMsgBox 31315 FFCustomMsgBox 31316 FFCustomMsgBox 31317 FFCustomMsgBox 31318 FFCustomMsgBox 31319 FFCustomMsgBox 31320 FFCustomMsgBox 31321 FFCustomMsgBox 31322 FFCustomMsgBox 31323 FFCustomMsgBox 31324 FFCustomMsgBox 31329 FFCustomMsgBox

Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Delete the associated examination. If the same symptom recurs after deletion, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Confirm software version and setups on the RU side. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Date of birth could not be Illegal birth date information was set. converted to the displaying format. Failed in obtaining the caption information (Stop alarm button). Message from the Image Reader could not be displayed. Failed in obtaining the caption information (System Terminating button). Failed in obtaining the caption information (User Utility button). Failed in obtaining the caption information (Study list setting button). It is conceivable that the database file was damaged or deleted. The RU software version conflicted with the message file version on the CR-IR 391CL side or the RU message file was damaged or otherwise abnormal. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

31330 FFCustomMsgBox 31331 FFCustomMsgBox 31332 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-197

Appx MT1-198
Event Event Source Description
Failed in obtaining the caption information (Version displaying button). Failed in obtaining the caption information (Cancel button). Failed in obtaining the button image (Clear button). Failed in obtaining the tool tip information (Clear button). Failed in displaying the thumbnail images. Failed in executing the scanner cleaning starting method of the Image Reader. Failed in obtaining the caption information (Cancel button). Failed in obtaining the caption information (Scanner cleaning button). Failed in inputting images.

Causes
It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the database file was damaged or deleted. The thumbnail image file was damaged, deleted, or otherwise abnormal. The RU is not ready for performing the method. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that there was a problem with the RU or line.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. There are no processing problems except for the inability to display thumbnail images. If the same symptom frequently occurs, initialize the image database. Check the RU status. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Check the RU and line. Check the RU status. Confirm software version and setups on the RU side. Confirm software version and setups on the RU side. There are no processing problems except for the inability to display thumbnail images. If the same symptom frequently occurs, initialize the image database. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

31333 FFCustomMsgBox 31334 FFCustomMsgBox 31335 FFCustomMsgBox 31336 FFCustomMsgBox 31337 FFCustomMsgBox

31339 FFCustomMsgBox 31340 FFCustomMsgBox 31341 FFCustomMsgBox 31343 FFCustomMsgBox 31344 FFCustomMsgBox 31346 FFCustomMsgBox

Image size could not be detected. It is conceivable that there was a problem with the RU. Failed in obtaining Image Reader error information. Failed in obtaining Image Reader status information. The RU software version conflicted with the message file version on the CR-IR 391CL side or the RU message file was damaged or otherwise abnormal. The RU software version conflicted with the message file version on the CR-IR 391CL side or the RU message file was damaged or otherwise abnormal.

31347 FFCustomMsgBox

31348 FFCustomMsgBox

Failed in thumbnail image creation The thumbnail image file was damaged, process. deleted, or otherwise abnormal. Failed in saving the list display setting (Waiting for study). Failed in saving the list display setting (Waiting for QA). Failed in saving the list display setting (Waiting for output). It is conceivable that the system was unstable or that the program was faulty. It is conceivable that the system was unstable or that the program was faulty. It is conceivable that the system was unstable or that the program was faulty.

31349 FFCustomMsgBox 31350 FFCustomMsgBox 31351 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-198

Appx MT1-199
Event Event Source Description
Failed in saving the list display setting (Already output). Failed in saving the list display setting (All). Failed in saving the list display setting (Today). Failed in customizing the list display. Failed in obtaining system setting information (Default menu code).

Causes
It is conceivable that the system was unstable or that the program was faulty. It is conceivable that the system was unstable or that the program was faulty. It is conceivable that the system was unstable or that the program was faulty. It is conceivable that the system was unstable or that the program was faulty. It is conceivable that the database file was damaged or deleted.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

31352 FFCustomMsgBox 31353 FFCustomMsgBox 31354 FFCustomMsgBox 31355 FFCustomMsgBox 31356 FFCustomMsgBox 31358 FFCustomMsgBox 31359 FFCustomMsgBox 31360 FFCustomMsgBox 31361 FFCustomMsgBox 31362 FFCustomMsgBox 31363 FFCustomMsgBox 31364 FFCustomMsgBox 31365 FFCustomMsgBox 31366 FFCustomMsgBox 31367 FFCustomMsgBox 31368 FFCustomMsgBox 31369 FFCustomMsgBox 31370 FFCustomMsgBox 31371 FFCustomMsgBox

Failed in obtaining the tool tip text. It is conceivable that the database file was damaged or deleted. Failed in obtaining the caption information (Title bar). Failed in obtaining the caption information (Option label). Failed in obtaining the version information. Option list could not be obtained. Failed in obtaining the registry information (Next multiple frame set No.). Failed in setting the registry information (Next multi-frame set No.). It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted.

It is conceivable that the file was damaged Restart. If the same symptom recurs, or deleted. perform a reinstallation. It is conceivable that the registry information was damaged or deleted. It is conceivable that the registry information was damaged or deleted. It is conceivable that the registry information was damaged or deleted. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Failed in obtaining the system It is conceivable that the database file was setting information (Series issuing damaged or deleted. type). Failed in obtaining the multi-frame The system was unstable. UID information. Failed in obtaining the cassette insertion enabled image. Failed in obtaining the cassette insertion disabled image. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted.

Failed in obtaining the image icon It is conceivable that the bitmap file was (Mis-exposure). damaged or deleted. Failed in obtaining the button image (Image style button). Failed in obtaining the button image (EDR button). It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-199

Appx MT1-200
Event Event Source Description
Failed in obtaining the button image (Function button). Failed in obtaining the button image (No. of output film button) Failed in obtaining the button image (IP size button). Failed in obtaining the button image (Film format button). Failed in obtaining the button image (Filing button). Failed in obtaining the button image (Film annotation button). Failed in obtaining the button image (Distribution code button). Failed in obtaining the button image (CS/SS button). Failed in obtaining system setting information (Serial port No. for connecting to XCON). Failed in obtaining the XCON device name. Image data line to the Image Reader (%s) has broken. Failed in obtaining the caption information. Failed in reading the bit-map file. Failed in obtaining the font information. Failed in refreshing the list. Requesting department code is illegal. Technologist code is illegal. Failed in searching the patient information. Failed in setting the connecting status to the RIS.

Causes
It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. The line was abnormal. It is conceivable that the database file was damaged or deleted. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the registry information was damaged or deleted. It is conceivable that the system was unstable or that the program was faulty.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

31372 FFCustomMsgBox 31373 FFCustomMsgBox 31374 FFCustomMsgBox 31375 FFCustomMsgBox 31376 FFCustomMsgBox 31377 FFCustomMsgBox 31378 FFCustomMsgBox 31379 FFCustomMsgBox 31380 FFCustomMsgBox 31381 FFCustomMsgBox 31382 FFCustomMsgBox 31386 FFCustomMsgBox 31387 FFCustomMsgBox 31388 FFCustomMsgBox 31389 FFCustomMsgBox 31390 FFCustomMsgBox 31391 FFCustomMsgBox 31392 FFCustomMsgBox 31393 FFCustomMsgBox

Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

The entered value contained an Make a proper entry. unacceptable character or was out of range or otherwise abnormal. The entered value contained an Make a proper entry. unacceptable character or was out of range or otherwise abnormal. Nothing matched the entered patient information. Check the patient information.

This error is attributable to an RIS problem Check RIS-side status or RIS setup. or RIS setup problem.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-200

Appx MT1-201
Event Event Source Description
Failed in obtaining the data. Failed in requesting of study start (PPS). Failed in requesting of study termination (PPS).

Causes

Remedies

Remarks

31394 FFCustomMsgBox 31395 FFCustomMsgBox 31396 FFCustomMsgBox 31397 FFCustomMsgBox 31398 FFCustomMsgBox 31399 FFCustomMsgBox 31400 FFCustomMsgBox 31401 FFCustomMsgBox 31402 FFCustomMsgBox 31403 FFCustomMsgBox 31404 FFCustomMsgBox 31405 FFCustomMsgBox 31406 FFCustomMsgBox 31407 FFCustomMsgBox 31408 FFCustomMsgBox 31409 FFCustomMsgBox 31410 FFCustomMsgBox 31411 FFCustomMsgBox

This error is attributable to an RIS problem Check RIS-side status or RIS setup. or RIS setup problem. The error is attributable, for instance, to an Check, for instance, the server operation inactive server or incorrect network status and network settings. settings. The error is attributable, for instance, to an Check, for instance, the server operation inactive server or incorrect network status and network settings. settings.

Failed in requesting of study abort The error is attributable, for instance, to an Check, for instance, the server operation (PPS). inactive server or incorrect network status and network settings. settings. Can not terminate. Failed in obtaining the label caption. Menu selected does not exist. Failed in obtaining the path information (image data folder). Failed in obtaining the parameter icon image. Failed in obtaining the caption information. Failed in communication with the connected device. Failed in evacuating the IP. Failed in setting the IP. Failed in setting the exposure size. Failed in setting the reference position for exposure. No response from the connected device. No response from the device sharing ID information. A study cannot be registered because the exposure menu registered in IDT is not registered in the CR-IR 391CL. It is conceivable that the file was damaged Restart. If the same symptom recurs, or deleted. perform a reinstallation. It is conceivable that the bitmap file was damaged or deleted. It is conceivable that the database file was damaged or deleted. The error is attributable to a problem with the connected equipment or connection setup. The connected equipment may be faulty. The connected equipment may be faulty. The connected equipment may be faulty. The connected equipment may be faulty. The connected equipment may be faulty. The connected equipment may be faulty. This error is attributable to an improperly registered menu. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Check the connected equipment, connection setup, and others. Confirm the connected device. Confirm the connected device. Confirm the connected device. Confirm the connected device. Confirm the connected device. Confirm the connected device. Check the menu registration information. It is conceivable that the database file was damaged or deleted. Restart. If the same symptom recurs, perform a reinstallation.

31412 FFCustomMsgBox

An image data line with the reader The connected equipment may be faulty. is cut off.

Confirm the connected device.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-201

Appx MT1-202
Event Event Source Description Causes Remedies
Check the connection setup. Restart. If the same symptom recurs, perform a reinstallation. Confirm the connected device. Check settings. Check settings. Check the connection setup. There is no practical problem because the limit values are transferred to the XCON. Confirm the connected device. Select a menu appropriate for the exposure, and then press the OK button that is displayed at the bottom of the window. The patient information database operation Restart. If the same symptom recurs, was wrong. perform a reinstallation. The system was unstable. The system was unstable. Invalid characters were used for the performed procedure step description, protocol name, or filter type. The radiation source-to-detector distance or radiation time did not consist of numerals only. The film output count or film size ID was out of range. The settings might be damaged. The system was unstable. The system was unstable. The system was unstable. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Since a standard setting will be used as a substitute to continue with the process, no particular response is required.

Remarks

31413 FFCustomMsgBox 31414 FFCustomMsgBox 31415 FFCustomMsgBox 31416 FFCustomMsgBox 31417 FFCustomMsgBox 31418 FFCustomMsgBox 31419 FFCustomMsgBox 31420 FFCustomMsgBox 31421 FFCustomMsgBox

Inconsistencies exist in the CR-IR The connection setup may be faulty. 391CL-RU connection setting of the system configuration. Failed in obtaining the caption information (RIS tab). A communication error with RIS occurred. Some exposure menus couldnt be registered. An exposure menu couldnt be registered. Failed in the reference of the reader device. It is conceivable that the database file was damaged or deleted. The connected equipment may be faulty. This error is attributable to an improperly set menu parameter or other setup failure. This error is attributable to an improperly set menu parameter or other setup failure. The connection setup may be faulty.

The condition value transmitted to The XCON settings (limit values) were x-ray device exceeded restriction. inconsistent with the exposure condition preset values for the menus. A communication error with RIS occurred. An exposure menu couldnt be decided. Failed in registering the study to the patient information database. Failed in image stitching processing. Failed in saving the exposure result information. Failed in determining actual exposure result values. The connected equipment may be faulty.

31422 FFCustomMsgBox 31423 FFCustomMsgBox 31424 FFCustomMsgBox 31425 FFCustomMsgBox

31426 FFCustomMsgBox 31427 FFCustomMsgBox 31428 FFCustomMsgBox 31429 FFCustomMsgBox


020-221-02E 01.08.2010 FM5563

Failed in acquiring coloring information. Failed in distribution process. Failed in displaying the study information list. Failed in setting patient information.

Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

CR-IR 391CL Service Manual

Appx MT1-202

Appx MT1-203
Event Event Source Description
Failed in obtaining the patient information. Failed in acquiring image (background). Failed in study transmission processing. Failed in study reception processing. Failed in connection to the other equipment. Some studies have not been registered appropriately. Failed in connection with the equipment. No studies have been registered successfully. Failed in mis-exposure processing. Failed in connection to the technologist database. Failed in registering exposure menus. Some exposure menus have not been registered appropriately. Connection to the portable equipment cannot be performed. Failed in mis-exposure processing. An attempt to restore images resulted in a failure. An attempt to acquire values from the Image Reader status information database resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the acquisition of the value from the error information database [ReaderUnit (RU)] Status information may not be displayed. Value acquisition from the image reader error information database failed while the connection to the image reader was established. The status information may not be displayed normally. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Check the equipment. Check the equipment. Re-set the portable equipment and then operate it again.

Causes
The system was unstable. It is conceivable that the bitmap file was damaged or deleted.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Confirm connection to the other equipment. Confirm connection to the other equipment. Confirm connection to the other equipment. Confirm connection to the other equipment.

Remarks

31430 FFCustomMsgBox 31431 FFCustomMsgBox 31432 FFCustomMsgBox 31433 FFCustomMsgBox 31434 FFCustomMsgBox 31435 FFCustomMsgBox 31436 FFCustomMsgBox 31437 FFCustomMsgBox 31438 FFCustomMsgBox 31439 FFCustomMsgBox 31440 FFCustomMsgBox 31463 FFCustomMsgBox 31471 FFCustomMsgBox 31472 FFCustomMsgBox

31473 FFInput

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-203

Appx MT1-204
Event Event Source Description
An attempt to acquire values from the Image Reader error information database resulted in a failure. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nfailed in the record of IP use frequency while reading Image. The IP use count was not successfully recorded during image reading. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

Causes

Remedies

Remarks

31473 FFCustomMsgBox

31474 FFInput

31474 FFCustomMsgBox 31475 FFInput

An attempt to register a count of IP use frequency resulted in a failure. ErrorCode:%1%nSubSystem:%2 The image could not be input during the %nSourceFile: %3%nSpotCode: image input process because the free %4%nDisk capacity shortage: The space on the disk was insufficient. input of the image cannot be executed

Press the button and continue the process. Delete unnecessary files, and then input the image. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

31475 FFCustomMsgBox 31476 FFCustomMsgBox 31478 FFInput 31500 FCRWeb

Image input is disabled due to insufficient free space remaining on the disk. An error may have occurred while inputting images from the Image Reader before. It failed in the acquisition of the value from the system setting database. It sets it as displayed. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in acquisition. Can not get information from LangStr.mdb.

Delete unnecessary files and retry image input. Operate according to the message displayed when the study starts. The settings for RU patient information Reinstall the system. display were not found in the system setup database. The character string was not successfully acquired. An internal system error occurred. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

31500 FFCustomMsgBox

An attempt to acquire character strings resulted in a failure. Existing character strings are displayed.

Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-204

Appx MT1-205
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in acquisition. Can not get information from LangMsgBox.mdb.

Causes
Message acquisition failed. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

31501 FCRWeb

31501 FFCustomMsgBox

An attempt to acquire messages failed. Existing character strings are displayed. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe user is not logged in. The user is not logged in.

Restart the server computer.

31502 FCRWeb

Log in.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

31502 FFCustomMsgBox

The user has not logged in.

User cannot be identified. The reason for Retry logging onto the system. such fact may be attributed to the following: (1)  The user was logged off the system while in operation. (2) The user is not logged on the system. (3) The server computer is not accessible. This user is logged off. Nothing particular. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

31503 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt is a logoffed user.

31503 FFCustomMsgBox 31504 FCRWeb

This user has been logged off the system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt is an illegal user. An unauthorized user attempted to log in.

Retry logging onto the system. Log in. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-205

Appx MT1-206
Event Event Source Description
An illegal user has been logged on the system. ErrorCode:%1%nSubSystem:%2 The current user does not have the %nSourceFile: %3%nSpotCode: privilege for performing this operation. %4%nThe login user doesnt have the execution authority.

Causes

Remedies
Retry logging onto the system. Log in as a user with operating privileges, and then retry.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

31504 FFCustomMsgBox 31505 FCRWeb

31505 FFCustomMsgBox 31506 FCRWeb

You are not authorized to perform this operation. ErrorCode:%1%nSubSystem: %2%nSourceFile: %3%nSpotCode:%4%n The inspection is excluding it. The selected study was being modified or examined by another computer.

Log onto the system with a properly authorized user name to retry this operation. Wait until the operation by the other computer terminates, and then retry. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

31506 FFCustomMsgBox

[31506] Selected study is being modified or performed. *Please Complete or Suspend ongoing study. >If the computer currently in use is unable to check, the study may be used by other user. >Otherwise, please restart all computers of this system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nRU is excluding it.

Just as the message states.

31507 FCRWeb

The selected study was being examined by Wait until the operation by the other another computer. computer terminates, and then retry.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-206

Appx MT1-207

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-207

Appx MT1-208
Event Event Source Description
[31507] A study is being performed. *Please Complete or Suspend ongoing study. >If the computer currently in use is unable to check, the study may be used by other user. >Otherwise, please restart all computers of this system.

Causes
Just as the message states.

Remedies

Remarks

31507 FFCustomMsgBox

31508 FCRWeb

ErrorCode:%1%nSubSystem:%2 The selected study was being modified or %nSourceFile: %3%nSpotCode: examined by another computer. %4%nThe inspection is excluding it.

Wait until the operation by the other computer terminates, and then retry.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

31508 FFCustomMsgBox

[31508] Selected study is being modified or performed. *Please Complete or Suspend ongoing study. >If the computer currently in use is unable to check, the study may be used by other user. >Otherwise, please restart all computers of this system. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nRU is excluding it.

Just as the message states.

31509 FCRWeb

The selected study was being examined by Wait until the operation by the other another computer. computer terminates, and then retry.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

31509 FFCustomMsgBox

[31509] A study is being performed. *Please Complete or Suspend ongoing study. >If the computer currently in use is unable to check, the study may be used by other user. >Otherwise, please restart all computers of this system.

Just as the message states.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-208

Appx MT1-209
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the information acquisition. Can not get information from EKarte.

Causes
The information could not be acquired from an electronic medical chart. This error is attributable to an incorrect setting in the Service Utility or an unconnected network.

Remedies
With the Service Utility, check the electronic medical chart settings. If the settings are correct, check the network cable, hub, and other network devices.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

31510 FCRWeb

31510 FFCustomMsgBox

An attempt to acquire information from the EMR resulted in a failure. Possible causes are: 1. EMR not started. 2. CL not connected to the EMR. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe inspection has already been deleted. The selected study was already deleted.

Confirm connection to the electronic medical chart device and retry communication. Continue processing if no information is acquired from the electronic medical chart device. Nothing particular. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

31511

FCRWeb

31511

FFCustomMsgBox

Study selected has already been deleted. An attempt to acquire information from the receipt computer resulted in a failure. Possible causes are: 1.  Receipt computer not started. 2.  CL not connected to the receipt computer. Settings to store images are about to be canceled. This study has been locked. The status of the verified study will be Completed, and an exposure will start again. The study on which image input was interrupted will resume . A study different from the image input-interrupted study will start.

Press [Update] to have the latest status displayed and then retry. Check the connection to the receipt computer. Retransmit then the study from the receipt computer.

31527 FFCustomMsgBox

31528 FFCustomMsgBox 31529 FFCustomMsgBox 31530 FFCusto]MsgBox

Images cannot be stored if continuing this operation. Do you wish to continue? Unlock the study and retry if you wish to delete the study. Do you wish to continue? Notice:  To continue, re-verify operations necessary to verify studies.

31531 FFCustomMsgBox 31532 FFCustomMsgBox

Are you sure?

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-209

Appx MT1-210
Event Event Source Description
Image acquisition failed.

Causes

Remedies
Check connection between the network cable and the hub. Close this dialog to resume receiving images. Note: I t may take about 10 minutes to resume. Close this dialog and wait for a while. Do not terminate the study until images are received.

Remarks

31533 FFCustomMsgBox

31534 FFCustomMsgBox 31535 FFCustomMsgBox 31536 FFCustomMsgBox 31537 FFCustomMsgBox 31538 FFCustomMsgBox 31539 FFCustomMsgBox 31842 FFCustomMsgBox 31850 FFCustomMsgBox 31851 FFCustomMsgBox 31852 FFCustomMsgBox 31853 FFCustomMsgBox 31854 FFCustomMsgBox 31855 FFCustomMsgBox 32300 FFInput

An error occurred during image processing. The Image Reader may be in use. Communication with the EMR resulted in a failure. An error is received from the EMR. A fatal error occurred. There are no applicable patients. There are two or more same studies on the P.Console. An attempt to connect to X-ray generator resulted in a failure An attempt to register reserved studies resulted in a failure An attempt to start reserved studies resulted in a failure. It is conceivable that the connected equipment may have a problem or the network may be unstable. The system was unstable. The system was unstable.

This event will not be displayed. Do you wish to continue? Confirm connection to the EMR device and retry. Contact your administrator. Contact your administrator. Delete duplicate instances of a study. Confirm the connected device. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Check information transmitted from the connected equipment. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

An error occurred with connecting The system was unstable. devices. An attempt to search reserved studies resulted in a failure. Received illegal data. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe unknown error occurred.\nPlease reactivate server PC. The system was unstable. It is conceivable that the connected equipment may have transmitted illegal information. An unknown error occurred during initialization process.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-210

Appx MT1-211
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the information acquisition Can not get information from SysConfig.mdb.

Causes
A system setup value could not be acquired. The database might be damaged.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). ErrorCode: 17001122

32500 FCRWeb

32500 CommonDefinition.cs In a situation where patient name This error is attributable to improper user text box IME control is exercised setup or application abnormality. so that alphabetical characters are used for pronunciation automatic input, the pronunciation automatic input definition is disabled Or, an attempt to acquire the pronunciation automatic input definition resulted in a failure. 32500 CommonDefinition.cs An attempt to acquire the IME The application is abnormal. setting from the setup file resulted in a failure. 32501 FCRWeb ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the information acquisition. Can not get information from Registry. Registry acquisition failed. The directory might be damaged.

Check the user settings. This error may occur when the user settings are defined so that a 1-byte alphanumeric pronunciation can be automatically input for a patient name. If the same symptom recurs, restart the application.

ErrorCode: 17001123 Achieve recovery by restarting the application. If the restart does not help, you can enter a patient name that consists of 1-byte alphanumeric characters. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

32502 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the information acquisition. Can not get information from Directry.ini.

A Directory.ini file access error occurred. The file might be damaged.

Restart both the server PC and client PC. If the same error recurs, perform a reinstallation.

32503 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the output of the operation log.

The operation log was not successfully output. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-211

Appx MT1-212
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the information acquisition. Can not get information from NetConfib.mdb.

Causes
An error occurred when an attempt was made to access a NetConfig.mdb file. The file might be damaged.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

32504 FCRWeb

32550 FFCrExamCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the information acquisition. Can not get information from Directry.ini.

A Directory.ini file access error occurred. The file might be damaged.

Restart. If the same symptom recurs, perform a reinstallation.

32551 FFCrExamCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in system construction DB (API) access.

A system setup value could not be acquired. The database might be damaged.

Restart. If the same symptom recurs, perform a reinstallation.

32600 FFEntryAddCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the value acquisition of Directry.ini.

A Directory.ini file access error occurred. The file might be damaged.

Restart. If the same symptom recurs, perform a reinstallation.

32601 FFEntryAddCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the value acquisition of SysConfig.

A system setup value could not be acquired. The database might be damaged.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-212

Appx MT1-213
Event Event Source Description Causes Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

32602 FFEntryAddCom

ErrorCode:%1%nSubSystem:%2 Registry acquisition failed. The directory %nSourceFile: %3%nSpotCode: might be damaged. %4%nIt failed in the acquisition of the registry.

32603 FFEntryAddCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred while outputting the log.

An error occurred during log output. It is Restart both the server PC and client PC. conceivable that the free space on the hard If the same error recurs, perform a disk may be insufficient. reinstallation. If the free space on the hard disk is insufficient, delete unnecessary files.

32650 FFDelInvalidCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the value acquisition of Directry.ini.

A Directory.ini file access error occurred. The file might be damaged.

Restart both the server PC and client PC. If the same error recurs, perform a reinstallation.

32651 FFDelInvalidCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the value acquisition of SysConfig.

A system setup value could not be acquired. The database might be damaged.

Restart. If the same symptom recurs, perform a reinstallation.

32652 FFDelInvalidCom

ErrorCode:%1%nSubSystem:%2 Registry acquisition failed. The directory %nSourceFile: %3%nSpotCode: might be damaged. %4%nIt failed in the acquisition of the registry.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-213

Appx MT1-214
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred while outputting the log.

Causes

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

32653 FFDelInvalidCom

An error occurred during log output. It is Restart both the server PC and client PC. conceivable that the free space on the hard If the same error recurs, perform a disk may be insufficient. reinstallation. If the free space on the hard disk is insufficient, delete unnecessary files.

32700 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the value acquisition of Directry.ini.

A Directory.ini file access error occurred. The file might be damaged.

Restart. If the same symptom recurs, perform a reinstallation.

32700 FFImageSwapCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the value acquisition of Directry.ini.

A Directory.ini file access error occurred. The file might be damaged.

Restart. If the same symptom recurs, perform a reinstallation.

32701 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the value acquisition of Sysconfig.

A system setup value could not be acquired. The database might be damaged.

Restart. If the same symptom recurs, perform a reinstallation.

32702 FFImageSwapCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt failed in the value acquisition of Sysconfig.

A system setup value could not be acquired. The database might be damaged.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-214

Appx MT1-215
Event Event Source Description Causes Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

32703 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 Registry acquisition failed. The directory %nSourceFile: %3%nSpotCode: might be damaged. %4%nIt failed in the acquisition of the registry.

32704 FFImageSwapCom

ErrorCode:%1%nSubSystem:%2 Registry acquisition failed. The directory %nSourceFile: %3%nSpotCode: might be damaged. %4%nIt failed in the acquisition of the registry.

Restart. If the same symptom recurs, perform a reinstallation.

32705 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred while outputting the log.

An error occurred during log output. It is Restart both the server application and conceivable that the free space on the hard client application. If the same error recurs, disk may be insufficient. perform a reinstallation. If the free space on the hard disk is insufficient, delete unnecessary files.

32706 FFImageSwapCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred while outputting the log.

An error occurred during log output. It is Restart both the server application and conceivable that the free space on the hard client application. If the same error recurs, disk may be insufficient. perform a reinstallation. If the free space on the hard disk is insufficient, delete unnecessary files.

32707 FFMenuChangeCom ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred while deleting the temporary file.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-215

Appx MT1-216
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error occurred while deleting the temporary file.

Causes

Remedies
Restart both the server PC and client PC. If the same error recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

32708 FFImageSwapCom

33100 FCRWeb

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Arbitrary Error Details.

A message related to a system operation.

Nothing particular.

34529 FFCustomMsgBox

[34529] The Height contains illegal character. > Single-byte numerical characters and period (.) are allowed for Height. Enter again. [34530] The Weight contains illegal character. > Single-byte numerical characters and period (.) are allowed for Weight. Enter again. [34531] The Height contains negative value. > Enter positive value for Height. [34532] The Weight contains negative value. > Enter positive value for Weight.

Just as the message states.

34530 FFCustomMsgBox

Just as the message states.

34531 FFCustomMsgBox 34532 FFCustomMsgBox 34533 FFCustomMsgBox

Just as the message states. Just as the message states. Only for veterinary hospital.

[34533] The Responsible person Just as the message states. contains illegal character. > Any double-byte characters and the characters below cannot be used for Responsible person. Enter again. #%&+?\*@ [34534] The Responsible Just as the message states. organization contains illegal character. > The characters below cannot be used for Responsible organization. Enter again. #%&+?\*@

34534 FFCustomMsgBox

Only for veterinary hospital.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-216

Appx MT1-217
Event Event Source Description Causes Remedies Remarks
Only for veterinary hospital. 34535 FFCustomMsgBox [34535] The Species contains Just as the message states. illegal character. > The characters below cannot be used for Breed. Enter again. #%&+?\*@ [34536] The Breed contains illegal Just as the message states. character. > The characters below cannot be used for Species. Enter again. #%&+?\*@ [34935] Height contains invalid character. > Enter correct information. [34936] Weight contains invalid character. > Enter correct information. [34937] The patient comment is too long. > Enter correct information. [34938] Responsible person's name is too long. > Enter correct information. [34939] Responsible organization's name is too long. > Enter correct information. Just as the message states. Just as the message states. Just as the message states. Just as the message states. Just as the message states. Only for veterinary hospital.

34536 FFCustomMsgBox

Only for veterinary hospital.

34935 FFCustomMsgBox 34936 FFCustomMsgBox 34937 FFCustomMsgBox 34938 FFCustomMsgBox 34939 FFCustomMsgBox 34940 FFCustomMsgBox

Only for veterinary hospital. Only for veterinary hospital. Only for veterinary hospital. Only for veterinary hospital.

[34940] The Breed contains illegal Just as the message states. character. > The characters below cannot be used for Breed. Enter again. # %% && + ? \ * @ < [34941] The Species contains Just as the message states. illegal character. > The characters below cannot be used for Species. Enter again. # %% && + ? \ * @ < [34942] The body length contains illegal character. > Only single-byte numerical characters and period (.) are allowed for Body length. Enter again. Just as the message states.

34941 FFCustomMsgBox

Only for veterinary hospital.

34942 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-217

Appx MT1-218
Event Event Source Description
[34943] The Weight contains invalid character. > Only single-byte numerical characters and period (.) are allowed for Weight. Enter again. An error of unknown cause occurred. File: Filename, Spot: Spot code, Code: Error code File: Filename, Spot: Spot code, Code: Error code File: Filename, Spot: Spot code, Code: Error code File: Filename, Spot: Spot code, Code: Error code File: Filename, Spot: Spot code, Code: Error code File: Filename, Spot: Spot code, Code: Error code The system settings were not successfully acquired. The system settings were not successfully acquired. The system settings were not successfully acquired. The system settings were not successfully acquired. The system settings were not successfully acquired. The system settings were not successfully acquired. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Check the Directory.ini file, and then restart %1= Error Code: The code that uniquely both the server application and client identifies an error. application. If the same error recurs, %2= Subsystem: The subsystem where an perform a reinstallation. error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart. If the same symptom recurs, perform a reinstallation.

Causes
Just as the message states.

Remedies

Remarks

34943 FFCustomMsgBox

40000 FFCustomMsgBox 40000 QADataObjCom 40000 QAImgInfoObjCom 40000 QAImgObjCom 40000 QAMarkerObjCom 40000 QAMaskObjCom 40000 QAManagerCom 40000 ViFileTransferCom

ErrorCode:%1%nSubSystem:%2 The system settings were not successfully %nSourceFile:%3%nSpotCode:% acquired. The Directory.ini file might be 4%n Comment missing or damaged.

40001 FFCustomMsgBox 40002 FFCustomMsgBox 40003 FFCustomMsgBox 40004 FFCustomMsgBox 40005 FFCustomMsgBox

An error of unknown cause occurred. An attempt to acquire study information failed. Data storage failed. Modified data cannot be stored. Modified data may have been lost. Failed in file output processing. Paper print processing failed.

The system was unstable.

After the image browse window is closed, make sure that the server computer is running. An error occurred during output processing. Confirm Windows regular printer setting and retry. An error occurred during output processing. Confirm the server computer status and retry.

40006 FFCustomMsgBox

Film output processing failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-218

Appx MT1-219
Event Event Source Description
Output processing of a work disk failed. Failed in initialize processing. In an environment where multiple client computers are connected, this can occur when client applications are started simultaneously. A problem has occurred for the database (SQL-Server).

Causes

Remedies
An error occurred during output processing. Confirm Windows regular printer setting and retry. Close the displayed message and restart the client application. Restart both the server application and client application. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

40007 FFCustomMsgBox

40008 FFCustomMsgBox

40009 FFCustomMsgBox

[40009] Failed in preset information operation. The following reason is presumable. 1. Database access erorr *Restart the server computer. >Contact your service engineer if restarting of the computer does not resolve the problem.

40010 FFCustomMsgBox

The max. preset limit for registrations has [40010] Registration cannot be performed due to exceeding of the been exceeded. max preset limit. *To add presets, delete some from the preset list.

Delete a part of the registrations from the preset list on the preset list edit window and try again.

40011

FFCustomMsgBox

[40011] The same preset name has already been registered. *Change the preset name and then re-execute.

Registration of an already existing preset name has been tried.

Change the preset name and try again.

40100 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

An exception error occurred during a component operation.

Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

40101 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

An illegal parameter was encountered during a component operation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-219

Appx MT1-220
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

Causes
An image information related error occurred during a component operation.

Remedies

Remarks

40102 FFMultiImgProc

Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

40103 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

A file was not successfully accessed during Restart both the server application and %1= Error Code: The code that uniquely a component operation. client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). A memory related error occurred during a component operation. Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

40104 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

40140 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

An exception error occurred during the normalization process.

40141 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

An illegal property was encountered during Restart both the server application and %1= Error Code: The code that uniquely the normalization process. client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-220

Appx MT1-221
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

Causes

Remedies

Remarks

40142 FFMultiImgProc

An image information related error Restart both the server application and %1= Error Code: The code that uniquely occurred during the normalization process. client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). A memory related error occurred during the Restart both the server application and %1= Error Code: The code that uniquely normalization process. client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). An internal table was not successfully created during the normalization process. Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

40144 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

40145 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

40150 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

FNC Proc Error (Exception handling was done).

40151 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

FNC Proc Error (Invalid Property).

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-221

Appx MT1-222
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

Causes
FNC Proc Error (Image processing error).

Remedies

Remarks

40152 FFMultiImgProc

Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

40160 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

An exception error occurred during a CR image process.

40161 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

An illegal property was encountered during Restart both the server application and %1= Error Code: The code that uniquely a CR image process. client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). An image information related error occurred during a CR image process. Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

40162 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

40166 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

A CR image process was not successfully executed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-222

Appx MT1-223
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

Causes
An exception error occurred during the polarity conversion process.

Remedies

Remarks

40180 FFMultiImgProc

Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

40186 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

The polarity conversion process not successfully performed.

40190 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

An exception error occurred during an LUT Restart both the server application and %1= Error Code: The code that uniquely process. client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). The file was not successfully accessed during an LUT process. Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

40193 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

40200 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

An exception error occurred during an image rotation/flipping process.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-223

Appx MT1-224
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

Causes

Remedies

Remarks

40201 FFMultiImgProc

Illegal properties were encountered when Restart both the server application and %1= Error Code: The code that uniquely an attempt was made to perform an image client application. If the same error recurs, identifies an error. rotation/flipping process. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). An image information related error occurred during an image rotation/flipping process. Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

40202 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

40206 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

The image rotation/flipping process was not successfully performed.

40210 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

An exception error occurred during the reduction process.

40216 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

The reduction process was not successfully Restart both the server application and %1= Error Code: The code that uniquely performed. client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-224

Appx MT1-225
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

Causes
An exception error occurred during the JPEG lossless conversion process.

Remedies

Remarks

40220 FFMultiImgProc

Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

40226 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

The JPEG lossless conversion process was not successfully performed.

40230 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

An exception error occurred during the JPEG lossy conversion process.

40236 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

An attempt to perform the JPEG lossy conversion process failed.

40240 FFMultiImgProc

ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Comment

An exception error occurred during a BMP conversion process.

40400 FFCustomMsgBox

Communication between processes failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-225

Appx MT1-226
Event Event Source Description
[File name][Function name][Error code]Comment [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment ErrorCode: %1 SubSystem: VI SourceFile: VwViewerCtrl. ctl[GetSysConfig] SpotCode: 0 SysConfig DB Access Error. VwSysDBOpen ErrorCode: %1 SubSystem: VI SourceFile: VwViewerCtrl. ctl[GetSysConfig] SpotCode: 0 SysConfig DB Access Error. VwSysDBClose Access to the system setup database resulted in a failure. [File name][Function name][Error code]Comment

Causes
The method return value for the interprocess communication API resulted in an error. The method return value for the interprocess communication API resulted in an error. The method return value for the image database access control resulted in an error. The method return value for the media database access control resulted in an error. The method return value for the interprocess communication API resulted in an error. A program error occurred.

Remedies
Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system, initialize the image database, and reinstall the application. Restart the system, initialize the media database, and reinstall the application. Restart the system. Contact the support center. Restart both the server PC and client PC

Remarks

40400 VwAnnotation ObjCom 40400 VwMsgBoxCtrl 40403 VwMsgBoxCtrl 40404 VwMsgBoxCtrl 40405 VwMsgBoxCtrl 40406 FFVwMsgBoxCtrl

%1=Detailed error code

40406 FFVwMsgBoxCtrl

A program error occurred.

Restart both the server PC and client PC

%1=Detailed error code

40406 FFCustomMsgBox 40406 VwMsgBoxCtrl

The problem is attributable to the system setting database. An error occurred when an attempt was made to connect or disconnect the system setup database access API, or acquire or set a value for the system setup database access API. The problem is attributable to the character string database. An error occurred with connection/ disconnection of the character string database access API. Restart. Check LangStr.mdb. Restart and then check SysConfig.mdb.

40407 FFCustomMsgBox 40407 VwMsgBoxCtrl

Access to the character string database resulted in a failure. [File name][Function name][Error code]Comment

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-226

Appx MT1-227
Event Event Source Description
ErrorCode: %1 SubSystem: VI SourceFile: %2 SpotCode: %3 LangStr DB Access Error. %4 %5 Access to the message box database resulted in a failure. [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment Access to the network setup database resulted in a failure. [File name][Function name][Error code]Comment

Causes
A program error occurred.

Remedies
Restart both the server PC and client PC

Remarks
%1=Error code %2=Source, Function name %3=Spot code %4=Detailed code of an error %5=Details of an error

40407 FFVwMsgBoxCtrl

40408 FFCustomMsgBox 40408 VwMsgBoxCtrl 40409 VwMsgBoxCtrl

The problem is attributable to the message box database. An error occurred with connection/ disconnection of the message box database access API. An error occurred when an attempt was made to connect or disconnect the flag database access API, or acquire or set a value for the flag database access API. The problem is attributable to the network setup database. An error occurred when an attempt was made to connect or disconnect the system setup database, or acquire or set a value for the system setup database (irreplaceable). A program error occurred. Restart and then check SysConfig.mdb. Restart. Check LangMsgBox.mdb. Restart, initialize the image database, and reinstall the application.

40411 40411

FFCustomMsgBox VwMsgBoxCtrl

40411

FFVwMsgBoxCtrl

ErrorCode: %1 SubSystem: VI SourceFile: %2 SpotCode: %3 NetConfig DB Access Error. %4 %5

Restart both the server PC and client PC

%1=Error code %2=Source, Function name %3=Spot code %4=Detailed code of an error %5=Details of an error

40412 FFCustomMsgBox 40412 VwMsgBoxCtrl 41000 QADataObjCom 41000 QAImgInfoObjCom 41000 QAImgObjCom 41000 QAMarkerObjCom 41000 QAMaskObjCom

Access to the customization setup The problem is attributable to the custom database resulted in a failure. setup database. [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment The method return value for the customize Restart, initialize the customization object was in error or illegal (irreplaceable). database, and reinstall the application. The hard disk was full. The hard disk was full. The hard disk was full. The hard disk was full. The hard disk was full. Delete unnecessary images. Delete unnecessary images. Delete unnecessary images. Delete unnecessary images. Delete unnecessary images.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-227

Appx MT1-228
Event Event Source Description
ErrorCode: Error code SubSystem: VI SourceFile: Filename SpotCode: Spot code Comment [File name][Function name][Error code]Comment The device is not ready. ErrorCode: Error code SubSystem: VI SourceFile: Filename SpotCode: Spot code Comment

Causes
The file was unsuccessfully downloaded.

Remedies
Check the connected equipment or network.

Remarks

41000 ViFileTransferCom

41000 QAManagerCom 41001 FFCustomMsgBox 41001 ViFileTransferCom

The hard disk was full. No floppy disk was set in position. The file was unsuccessfully uploaded.

Delete unnecessary images. Set media that is appropriate for the device. Check the connected equipment or network.

41001 ViClientInfoAccess

ErrorCode:%1%nSubSystem:%2 The key character string was not specified. Restart. If the same symptom recurs, %nSourceFile:%3%nSpotCode:% perform a reinstallation. 4%n Comment

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

41002 FFCustomMsgBox 41002 ViFileTransferCom

The hard disk is full. ErrorCode: Error code SubSystem: VI SourceFile: Filename SpotCode: Spot code Comment

The file to be copied was too large to fit onto the media at the receiving end. Failed in reading a file.

Switch to larger-capacity media. Check whether the file exists.

41002 ViClientInfoAccess

ErrorCode:%1%nSubSystem:%2 A Directory.ini access error occurred. %nSourceFile:%3%nSpotCode:% The error is attributable to a nonexistent 4%n Comment file or an illegal definition in the file.

Check the Directory.ini file, and then restart %1= Error Code: The code that uniquely both the server application and client identifies an error. application. If the same error recurs, %2= Subsystem: The subsystem where an perform a reinstallation. error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Check the system setup. Check whether the folder exists at the file write destination.

41003 FFCustomMsgBox 41003 ViFileTransferCom

Destination for file copy is illegal. ErrorCode: Error code SubSystem: VI SourceFile: Filename SpotCode: Spot code Comment

An invalid pathname was specified as the file copy destination. The file was unsuccessfully written.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-228

Appx MT1-229
Event Event Source Description Causes Remedies Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). 41003 ViClientInfoAccess ErrorCode:%1%nSubSystem:%2 The specified setup information file was not Restart. If the same symptom recurs, %nSourceFile:%3%nSpotCode:% successfully accessed. The file might be perform a reinstallation. 4%n Comment damaged.

41004 FFCustomMsgBox 41004 ViFileTransferCom

E-mail program cannot be started. Outlook was not properly set up. ErrorCode: Error code SubSystem: VI SourceFile: Filename SpotCode: Spot code Comment ErrorCode: Error code SubSystem: VI SourceFile: Filename SpotCode: Spot code Comment The system has not been logged on. The system has already been logged off. You have been logged off the system or User has been changed. No printers have been registered. Free disk space is insufficient. This study includes images not retrieved into the hard disk. The processing cannot be continued in the specified study. Specified destination may have been a data storage disk. Notice: The disk will be inconsistent if storing in data storage disk. This operation is unable to perform. File deletion failed.

Exit the CR-IR 391CL and then complete Outlook setup. Check whether the file exists.

41005 ViFileTransferCom

An attempt to operate a CAB file failed.

Restart the system. Contact the support center.

41016 FFCustomMsgBox

Press OK to close the image browse window and open the log-in window. To keep the image browse window open, press Cancel. Press OK to close the image browse window and open the log-in window. To keep the image browse window open, press Cancel. Press OK to close the image browse window and open the log-in window. To keep the image browse window open, press Cancel. Register printers and retry. Delete unnecessary files to increase free disk space. Deactivate the image browse function, and then activate it again. This operation is unable to perform. Reconfirm or verify this study. Are you sure you want to store?

41017 FFCustomMsgBox

41018 FFCustomMsgBox

41019 FFCustomMsgBox 41020 FFCustomMsgBox 41025 FFCustomMsgBox 41026 FFCustomMsgBox 41027 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-229

Appx MT1-230
Event Event Source Description
No study selected. Method of calling is incorrect. Un-permitted scripts have been called directly. An error of unknown cause occurred. Image display is disabled because specified images cannot be found. Failed in initialization processing. A timeout occurred. Failed in starting up image viewer.

Causes

Remedies
Select a study and retry it. Execute again following the correct start procedure. Contact your service engineer. Press the button below to close this dialog and terminate the system. To exit the image viewer, press the button below. Contact your service engineer. Press the button below to close this dialog and terminate the system. Contact your service engineer. +Press the button below to close this dialog and terminate the system. Restart the server computer and retry. Contact your service engineer if the same symptom recurs even after it has been restarted. Ensure that the network cable has been connected correctly. This operation is unable to perform. The C@Rna newly-arrived information program is not running normally, or the network may have problems. Confirm that the C@Rna newly-arrived information program is running. The C@Rna newly-arrived information program is not running normally, or the network may have problems. Confirm that the C@Rna newly-arrived information program is running.

Remarks

41029 FFCustomMsgBox 41030 FFCustomMsgBox 41031 FFCustomMsgBox 41032 FFCustomMsgBox 41033 FFCustomMsgBox 41034 FFCustomMsgBox 41035 FFCustomMsgBox

41036 FFCustomMsgBox 41037 FFCustomMsgBox 41038 FFCustomMsgBox

An attempt to connect to C@Rna data center resulted in a failure. This operation is not allowed for retrieved studies from disks. Failed in obtaining case study images.

41039 FFCustomMsgBox

Failed in obtaining anatomical drawings.

41040 FFCustomMsgBox

[41040] A study is being performed. *Please Complete or Suspend ongoing study. >If the computer currently in use is unable to check, the study may be used by other user. >Otherwise, please restart all computers of this system.

Just as the message states.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-230

Appx MT1-231
Event Event Source Description
The disk drive used for image view purpose has not been set up properly. File: Filename, Spot: Spot code, Code: Error code HDD FULL. [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment Arbitrary information. [File name][Function name][Error code]Comment ErrorCode: %1 SubSystem: VI SourceFile: %2 SpotCode: %3 Cant Get Bitmap (Processing continuation). %4 %5 [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment ErrorCode: -2402 SubSystem: VI SourceFile: VwViewerCtrl. ctl[GetSysConfig] SpotCode: 0 SysConfig DB Access Failure (Processing continuation). VwSysDBGetValueComImgFileNameType The hard disk was full. The hard disk was full. The specified path was not found. No medium is ready. The capacity of the media targeted for copy was insufficient. The method return value for the delivery instruction component resulted in an error (a process other than the delivery process can be continued). Arbitrary information. Failed in acquiring a bitmap (replaceable). A program error occurred.

Causes

Remedies
With the Service Utility, set the disk drive for viewing. Delete unnecessary images. Delete unnecessary images. Check path settings. Set a medium in its position. Replace the media for anyone of larger capacity. Delete unnecessary images.

Remarks

41212 FFCustomMsgBox 41400 VwAnnotation ObjCom 41400 VwMsgBoxCtrl 41401 VwMsgBoxCtrl 41402 VwMsgBoxCtrl 41403 VwMsgBoxCtrl 41410 VwMsgBoxCtrl

42000 QAManagerCom 42400 VwMsgBoxCtrl 42400 FFVwMsgBoxCtrl

Processing can be continued Check that the entire bitmap is acquired. Restart both the server PC and client PC %1=Error code %2=Source, Function name %3=Spot code %4=Detailed code of an error %5=Details of an error

42401 VwMsgBoxCtrl 42402 VwMsgBoxCtrl 42402 FFVwMsgBoxCtrl

The return value for the custom message box control resulted in an error.

Nothing particular.

An error occurred when obtaining a system Check SysConfig.mdb. setup database access API value or the obtained value was illegal (replaceable). A program error occurred. Restart both the server PC and client PC

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-231

Appx MT1-232
Event Event Source Description
ErrorCode: %1 SubSystem: VI SourceFile: %2 SpotCode: %3 SysConfig DB Access Failure (Processing continuation). %4 %5 [File name][Function name][Error code]Comment ErrorCode: %1 SubSystem: VI SourceFile: frmViImgFileOutput. frm[SetCaption ()] SpotCode: 316 LangStr DB Access Failure (Processing continuation). StrDBGet (46506) Ret = %2 ErrorCode: %1 SubSystem: VI SourceFile: frmViImgFileOutput. frm[SetCaption ()] SpotCode: 303 LangStr DB Access Failure (Processing continuation). StrDBGet (46507) Ret = %2 ErrorCode: %1 SubSystem: VI SourceFile: frmViImgFileOutput. frm[SetCaption ()] SpotCode: 303 LangStr DB Access Failure (Processing continuation). StrDBGet (46508) Ret = %2 ErrorCode: %1 SubSystem: VI SourceFile: %2 SpotCode: %3 LangStr DB Access Failure (Processing continuation). %4 %5 [File name][Function name][Error code]Comment

Causes
A program error occurred.

Remedies
Restart both the server PC and client PC

Remarks
%1=Error code %2=Source, Function name %3=Spot code %4=Detailed code of an error %5=Details of an error

42402 FFVwMsgBoxCtrl

42403 VwMsgBoxCtrl 42403 FFVwMsgBoxCtrl

An error occurred when obtaining a Check LangStr.mdb. character string database access API value (replaceable). A program error occurred. Restart both the server PC and client PC %1=Detailed error code %2=Detailed error code

42403 FFVwMsgBoxCtrl

A program error occurred.

Restart both the server PC and client PC

%1=Detailed error code %2=Detailed error code

42403 FFVwMsgBoxCtrl

A program error occurred.

Restart both the server PC and client PC

%1=Detailed error code %2=Detailed error code

42403 FFVwMsgBoxCtrl

A program error occurred.

Restart both the server PC and client PC

%1=Error code %2=Source, Function name %3=Spot code %4=Detailed code of an error %5=Details of an error

42404 VwMsgBoxCtrl

The return value for the message box database access API resulted in an error.

Check LangMsgBox.mdb.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-232

Appx MT1-233
Event Event Source Description
[File name][Function name][Error code]Comment

Causes

Remedies

Remarks

42405 VwMsgBoxCtrl

The FF32 library (FF32dll) return value is Check the registry key setting. in error (registry acquisition/setup failed). Replaceable. When the option key registry data is acquired, no error occurs even if the key is not acquired. A program error occurred. Restart both the server PC and client PC %1=Error code %2=Source, Function name %3=Spot code %4=Detailed code of an error %5=Details of an error

42405 FFVwMsgBoxCtrl

ErrorCode: %1 SubSystem: VI SourceFile: %2 SpotCode: %3 FF32 Access Failure (Probably acquisition of Registry goes wrong.) %4 %5 [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment ErrorCode: %1 SubSystem: VI SourceFile: %2 SpotCode: %3 NetConfig DB Access Failure (Processing continuation). %4 %5 [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment Arbitrary information. Arbitrary information. Arbitrary information. Failed to get (%1). ImageID: %2. ErrorCode: Error code SubSystem: VI SourceFile: Filename SpotCode: Spot code Comment Selected image cant show.

42406 VwMsgBoxCtrl 42407 VwMsgBoxCtrl 42407 FFVwMsgBoxCtrl

No tag information was set up though it must have been set up beforehand (irreplaceable). An error occurred when obtaining a network setup database value or obtained value was not correct (replaceable). A program error occurred.

Nothing particular. Check NetConfig.mdb. Restart both the server PC and client PC %1=Error code %2=Source, Function name %3=Spot code %4=Detailed code of an error %5=Details of an error

42408 VwMsgBoxCtrl 42409 VwMsgBoxCtrl 43000 QADataObjCom 43000 QAImgInfoObjCom 43000 QAManagerCom 43001 QAImgInfoObjCom 43400 VwMsgBoxCtrl

The return value for the customize object was in error or illegal (replaceable). Failed in obtaining/setting an FF32 library value (replaceable). Arbitrary information. Arbitrary information. Arbitrary information. Arbitrary information. Arbitrary information.

Check Custom.adp. Check the Directory.ini file. Processing can be continued Processing can be continued Processing can be continued Restart the system. Contact the support center. Processing can be continued

43410 QAChgPrmCtrl

Image display failed.

Restart the system. Contact the support center.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-233

Appx MT1-234
Event
43411

Event Source
QAChgPrmCtrl

Description
Selected image cant show. Logical Program Error. %n %1 %n %2

Causes
Image display failed. A program error occurred.

Remedies
Restart the system. Contact the support center. Restart the system. Contact the support center. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Delete unnecessary files to increase free disk space. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

Remarks

Error occurred in RunWithParam () The image process was not successfully of FMImgHandCtrl. performed.

43510 QAChgPrmCtrl 43512 FFMaCommon

43513 FFMaCommon

Catch Exception Error. %n %1 %n %2

An exception error occurred.

43514 FFMaCommon

Out Of Memory Error. %n %1 %n %2

Memory allocation failed.

43515 FFMaCommon

Free Memory Error. %n %1 %n %2

Memory deallocation failed.

43516 FFMaCommon 43517 FFMaCommon

Disk Full Error. %n %1 %n %2 DataBase Error. %n %1 %n %2

The built-in hard disk does not have a sufficient free space. The database was not successfully operated.

43518 FFMaCommon

Debug Log OutPut. %n %1 %n %2

This is an event log output for debugging. Confirm the situation in which the error It is not generated under normal conditions. occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. EDR computation failed. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center.

43520 QAChgPrmCtrl 43521 QAChgPrmCtrl 43522 QAChgPrmCtrl

Error occurred in ExecuteEDR () of EDRCom.

Error occurred in The EDR backup file was not successfully SetEDRProperties () of EDRCom. created. Error occurred in MakeEDRBackupFile () of EDRCom. An attempt to perform EDR property setup failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-234

Appx MT1-235
Event Event Source Description
Error occurred in RemoveDstbDest () of QAManagerCom. Error occurred in SetPrintDest () of QAManagerCom. Error occurred in SetFilingDest () of QAManagerCom. Error occurred in SetDisplayDest () of QAManagerCom. Error occurred in AddDstbDest () of QAManagerCom.

Causes
The distribution/delivery destination was not successfully deleted. An attempt to change the PRINT attribute failed. An attempt to change the FILE attribute failed. An attempt to change the DISPLAY attribute failed. The distribution/delivery destination was not successfully deleted.

Remedies
Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center.

Remarks

43530 QAChgPrmCtrl 43531 QAChgPrmCtrl 43532 QAChgPrmCtrl 43533 QAChgPrmCtrl 43534 QAChgPrmCtrl 43535 QAChgPrmCtrl 43536 QAChgPrmCtrl 43537 QAChgPrmCtrl

PixelDensity of An ImageDensityOut setting of -1 was MenuDefaultParameter is equal to detected. -1. Skip change ImageDensityOut.

Selected MPM-Code hasnt An undefined menu code was encountered Restart the system. Contact the support default parameters in some param when GetByMenu was used. center. files. FilmOrientation of The value obtained for FilmOrientation MenuDefaultParameter isnt 0 or setting acquisition was neither 0 nor 1. 1.%nSet default 0 (LANDSCAPE). A program error occurred. Restart the system. Contact the support center. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Delete unnecessary files to increase free disk space.

43600 FFMaCommonImage Logical Program Error. %n %1 %n %2

43601 FFMaCommonImage Catch Exception Error. %n %1 %n %2

An exception error occurred.

43602 FFMaCommonImage Out Of Memory Error. %n %1 %n %2

Memory allocation failed.

43603 FFMaCommonImage Free Memory Error. %n %1 %n %2

Memory deallocation failed.

43604 FFMaCommonImage Disk Full Error. %n %1 %n %2

The built-in hard disk does not have a sufficient free space.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-235

Appx MT1-236
Event Event Source Description
Logical Program Error. %n %1 %n %2

Causes
A program error occurred.

Remedies
Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Delete unnecessary files to increase free disk space. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Perform input again after deleting inserted annotations and markers. Check the checkbox at the bottom right of the window and retry. Close the dialog and retry. Close the dialog and retry.

Remarks

43700 FFTsCommon

43701 FFTsCommon

Catch Exception Error. %n %1 %n %2

An exception error occurred.

43702 FFTsCommon

Out Of Memory Error. %n %1 %n %2

Memory allocation failed.

43703 FFTsCommon

Free Memory Error. %n %1 %n %2

Memory deallocation failed.

43704 FFTsCommon 43705 FFTsCommon

Disk Full Error. %n %1 %n %2 Catch DB exception. %n %1 %n %2

The built-in hard disk does not have a sufficient free space. An exception occurred when an attempt was made to access a database.

44005 FFCustomMsgBox 44016 FFCustomMsgBox 44023 FFCustomMsgBox 44024 FFCustomMsgBox 44030 FFCustomMsgBox

The number of annotations exceeded the display-allowable limit. No image has been selected. An image display could not be made because an operation is being performed. A display could not be cleared because an operation is being performed. Input 3 or more vertices.

The number of annotations and markers inserted for one image on the viewer window has exceeded 32.

This confirmation dialog is displayed at the To create a polygon, 3 or more vertices are time of insertion of a polygonal annotation required. on the viewer window when it is tried to Input 3 or more vertices. establish a polygonal shape with fewer than three apexes.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-236

Appx MT1-237
Event Event Source Description
[44040] The following preset(s) will be deleted. %s +Do you wish to proceed? 44041 FFCustomMsgBox 44042 FFCustomMsgBox [44041] This name already exists. +Do you wish to overwrite? [44042] It cannot be changed as preset of the same name exists. *Change the name. 44043 FFCustomMsgBox [44043] Prohibited characters are included in the preset name. *Retry input. 44044 FFCustomMsgBox [44044] Input name is too long. Up to 64 characters can be entered. *Change the preset name. 44045 FFCustomMsgBox The registerable upper limit for the selected Change the anatomical region to be [44045] Registration cannot be anatomical region has been exceeded. registered or delete a part from the preset performed for the anatomical list and try again. region selected as the registerable presets exceed the upper limit. *Too add, change the anatomical region to register or delete some from the preset list. 44046 FFCustomMsgBox [44046] Preset name has not been entered. *Enter the preset name. 44400 VwMsgBoxCtrl 44401 VwMsgBoxCtrl 44401 FFVwMsgBoxCtrl [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment ErrorCode: %1 SubSystem: VI SourceFile: %2 SpotCode: %3 An unexpected Method call. %4 %5 The method return value for the log save control resulted in an error.xxx An unexpected method call (called up at an impossible timing, being possible though to continue processing). A program error occurred. Nothing particular. Nothing particular. Restart both the server PC and client PC %1=Error code %2=Source, Function name %3=Spot code %4=Detailed code of an error %5=Details of an error No preset name has been entered. Enter the preset name and try again. The preset name to be registered or changed contains more than the permitted 64 characters. Change the input name to within 64 characters and try again. The preset name to be registered or changed contains prohibited characters. Reenter without the prohibited characters. Change to an already existing preset name Change the preset name and try again. has been tried. Nothing particular.

Causes

Remedies
Nothing particular.

Remarks

44040 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-237

Appx MT1-238
Event Event Source Description
Logical Program Error. %n %1 %n %2

Causes
A program error occurred.

Remedies
Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Delete unnecessary files to increase free disk space. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center.

Remarks

44500 FFRtrvProcCtrl

44501 FFRtrvProcCtrl

Catch Exception Error. %n %1 %n %2

An exception error occurred.

44502 FFRtrvProcCtrl

Out Of Memory Error. %n %1 %n %2

Memory allocation failed.

44503 FFRtrvProcCtrl

Free Memory Error. %n %1 %n %2

Memory deallocation failed.

44504 FFRtrvProcCtrl 49000 QADataObjCom 49000 QAImgInfoObjCom 49000 QAImgObjCom 49000 QAMarkerObjCom 49000 QAMaskObjCom 49000 QAChgPrmCtrl 49000 QAManagerCom 49001 QAImgInfoObjCom 49001 QAManagerCom

Disk Full Error. %n %1 %n %2 File: Filename, Spot: Spot code, Code: Error code File: Filename, Spot: Spot code, Code: Error code File: Filename, Spot: Spot code, Code: Error code File: Filename, Spot: Spot code, Code: Error code File: Filename, Spot: Spot code, Code: Error code Error level is Warning (level2), Information or Logical Error. File: Filename, Spot: Spot code, Code: Error code Failed to get (%1). ImageID: %2. Error in FFGetString.

The built-in hard disk does not have a sufficient free space. CR-IR 391CL error level 2/3/9 message. CR-IR 391CL error level 2/3/9 message. CR-IR 391CL error level 2/3/9 message. CR-IR 391CL error level 2/3/9 message. CR-IR 391CL error level 2/3/9 message. CR-IR 391CL error level 2/3/9 message. CR-IR 391CL error level 2/3/9 message. Program error. Program error.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-238

Appx MT1-239
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%n Comment

Causes
A parameter out-of-range error (internal system error) occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

49001 ViFileTransferCom

49002 QAManagerCom 49002 ViFileTransferCom

Error in SysDB Library. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%n Comment

Parameter error. A parameter error (internal system error) occurred.

Restart the system. Contact the support center. Restart. If the same symptom recurs, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

49003 QAManagerCom

Error in NetDB Library.

An error attributable to a program fault (an Restart the system. Contact the support error that could not occur in the market) center. occurred. An unexpected return value was delivered from a method. Memory allocation failed. Windows resource acquisition failed. An abnormal return from a Windows API. An error highly attributable to a program fault (an error that could not occur in the market) occurred. An unexpected return value was delivered from a method. Memory allocation failed. Windows resource acquisition failed. An abnormal return from a Windows API. Program error. Program error. Program error. Program error. Restart both the server application and %1= Error Code: The code that uniquely client application. If the same error recurs, identifies an error. perform a reinstallation. If the reinstallation %2= Subsystem: The subsystem where an does not help, confirm the situation in error occurred. which the error occurred, and submit the %3= Source File: The program file where event log to the manufacturer. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center.

49003 ViFileTransferCom

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%n Comment

49004 QAManagerCom 49005 QAManagerCom 49006 QAManagerCom 49007 QAManagerCom

Error in ImageDB Access. Error in FFCreateUID. Error in FFCreateStudyUID. Error in ImgDelivery.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-239

Appx MT1-240
Event Event Source Description
Error in FFMultiImgProc. Error in FFMultiImgProc. Error in FFMultiImgProc. Error in VIFileTransferCom. Error in VIFileTransferCom. ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%n Comment Program error. Program error. Program error. Program error. Program error. An exception error occurred.

Causes

Remedies
Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

49008 QAManagerCom 49009 QAManagerCom 49010 QAManagerCom 49011 QAManagerCom

49012 QAManagerCom 49019 ViFileTransferCom

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

49101 QAManagerCom 49102 QAManagerCom 49103 QAManagerCom 49104 QAManagerCom 49105 QAManagerCom 49106 QAManagerCom 49107 QAManagerCom 49108 QAManagerCom 49151 QAManagerCom 49152 QAManagerCom 49301 QAManagerCom
020-221-02E 01.08.2010 FM5563

Error about StudyInstanceUIDType (0007,F244). Error about SeriesInstanceUIDType (0007,F245). Error about StudyInstanceUID (0020,000D). Error about SeriesInstanceUID (0020,000E). Error about ImageUID (0009,XX05).

Program error. Program error. Program error. Program error. Program error.

Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center.

Error about FilmUID (0009,XX0C). Program error. Error about MultiFrameUID (0007,F200). Error about ID (0007,F001). Error about QAFlag. Error about Lock (0007,F020). Error about Patients Name (0010,0010). Program error. Program error. Program error. Program error. Program error.

CR-IR 391CL Service Manual

Appx MT1-240

Appx MT1-241
Event Event Source Description
Error about Patient ID (0010,0020). Error about Patients Birth Date (0010,0030). Error about Patients Sex (0010,0040). Error about Accession Number (0008,0050). Error about DepartmentName (0009,XX91). Error about DepartmentName (0009,XX92). Error about InspectNumber (0021,XX20). Program error. Program error. Program error. Program error. Program error. Program error. Program error.

Causes

Remedies
Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center.

Remarks

49302 QAManagerCom 49303 QAManagerCom 49304 QAManagerCom 49305 QAManagerCom 49306 QAManagerCom 49307 QAManagerCom 49308 QAManagerCom 49309 QAManagerCom 49310 QAManagerCom 49311 QAManagerCom

Error about Modality (0008,0060). Program error. Error about StudyDate (0008,0020). Error about RequestingService (0032,1033). Error about OrderNumber (0007,F240). Error about DepartmentCode (0007,F246). Error about StudyID (0020,0010). Error about RequestedProcedureID (0040,1001). [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment Program error. Program error. Program error. Program error. Program error. Program error. An FF32 library (FF32.dll) return value error (inreplaceable). An FF32 library (FF32.dll) return value error (inreplaceable).

49312 QAManagerCom 49313 QAManagerCom 49314 QAManagerCom 49315 QAManagerCom 49400 VwAnnotation ObjCom 49400 VwMsgBoxCtrl

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-241

Appx MT1-242
Event Event Source Description
ErrorCode: %1 SubSystem: VI SourceFile: VwViewerCtrl. ctl[GetServerReg] SpotCode: 0 FF32 Error. IVSetClientConfigStr (ComImgFileNameType) ErrorCode: %1 SubSystem: VI SourceFile: %2 SpotCode: %3 FF32 Error. %4 %5 [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment ErrorCode: %1 SubSystem: VI SourceFile: %2 SpotCode: %3 Method Argument Error. %4 %5 [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment [File name][Function name][Error code]Comment ErrorCode: %1 SubSystem: VI SourceFile: %2 SpotCode: %3 Memory or Resource cannot be gained. %4 %5 [File name][Function name][Error code]Comment

Causes
A program error occurred.

Remedies
Restart both the server PC and client PC

Remarks
%1=Detailed error code

49400 FFVwMsgBoxCtrl

49400 FFVwMsgBoxCtrl

A program error occurred.

Restart both the server PC and client PC

%1=Error code %2=Source, Function name %3=Spot code %4=Detailed code of an error %5=Details of an error

49401 VwMsgBoxCtrl 49401 QAManagerCom 49401 FFVwMsgBoxCtrl

A method argument type error (for instance, there were no objects). A method argument type error (for instance, there were no objects). A program error occurred.

Restart the system. Contact the support center. Restart the system. Contact the support center. Restart both the server PC and client PC %1=Error code %2=Source, Function name %3=Spot code %4=Detailed code of an error %5=Details of an error

49402 QAManagerCom 49402 VwMsgBoxCtrl 49403 VwMsgBoxCtrl 49403 FFVwMsgBoxCtrl

No tag information was set up though it must have been set up beforehand (irreplaceable). No tag information was set up though it must have been set up beforehand (irreplaceable). Failed in acquiring memory handle resources. A program error occurred.

Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart both the server PC and client PC %1=Error code %2=Source, Function name %3=Spot code %4=Detailed code of an error %5=Details of an error

49404 VwMsgBoxCtrl

Windows API return value resulted in an error.

Restart the system. Contact the support center.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-242

Appx MT1-243
Event Event Source Description
[File name][Function name][Error code]Comment Error about FileDensity (0007,F082). Program error.

Causes
Windows API return value resulted in an error.

Remedies
Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart the system. Contact the support center. Restart both the server PC and client PC

Remarks

49404 QAManagerCom 49405 QAManagerCom 49406 QAManagerCom 49407 QAManagerCom 49408 QAManagerCom 49409 QAManagerCom 49410 QAManagerCom 49411 QAManagerCom

Error about FileProc (0007,F092). Program error. Error about PrintHost (0007,F071). Error about PrintDensity (0007,F081). Error about PrintProc (0007,F091). Error about DisplayHost (0007,F073). Error about DisplayDensity (0007,F083). Error about DisplayProc (0007,F093). Error about ImageFiling (50F1,XX12). Error about ImageDensityOut (50F1,XX05). Error about InputProtocol (0007,F006). Error about ImageFileURL (0007,F100). Error about ImageManager (0009,XX04). [File name][Function name][Error code]Comment ErrorCode: %1 SubSystem: VI SourceFile: %2 SpotCode: %3 Secondary detection code Error. %4 %5 Program error. Program error. Program error. Program error. Program error. Program error. Program error. Program error. Program error. Program error. Program error. An error occurred with the return value of the secondary detection code. A program error occurred.

49412 QAManagerCom 49413 QAManagerCom 49414 QAManagerCom 49415 QAManagerCom 49416 QAManagerCom 49417 QAManagerCom 49498 VwMsgBoxCtrl 49498 FFVwMsgBoxCtrl

%1=Error code %2=Source, Function name %3=Spot code %4=Detailed code of an error %5=Details of an error

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-243

Appx MT1-244
Event Event Source Description
ErrorCode: -9499 SubSystem: VI SourceFile: VwViewerCtrl. ctl[BeginWebService] SpotCode: 0 Secondary detection code Error. WebService URL = %1 ErrorCode: -9499 SubSystem: VI SourceFile: VwViewerCtrl. ctl[EndWebService] SpotCode: 0 Secondary detection code Error. Set objSOAPClient = Nothing ErrorCode: %1 SubSystem: VI SourceFile: VwViewerCtrl.ctl[Init] SpotCode: 0 Secondary detection code Error. GetSysConfig [File name][Function name][Error code]Comment ErrorCode: -9499 SubSystem: VI SourceFile: VwViewerCtrl. ctl[GetSysConfig] SpotCode: 0 Exception Error occurred. %1:%2 49499 FFVwMsgBoxCtrl ErrorCode: %1 SubSystem: VI SourceFile: [Get MeasureEditComplete] SpotCode: 0 Exception Error occurred. %2:%3 49499 FFVwMsgBoxCtrl ErrorCode: %1 SubSystem: VI SourceFile: [Let MeasureEditComplete] SpotCode: 0 Exception Error occurred. %2:%3 A program error occurred. Restart both the server PC and client PC %1=Detailed error code %2=Detailed error code %3=Details of an error A program error occurred. Restart both the server PC and client PC %1=Detailed error code %2=Detailed error code %3=Details of an error

Causes
A program error occurred.

Remedies
Restart both the server PC and client PC

Remarks
%1=WebService connection URL

49498 FFVwMsgBoxCtrl

49498 FFVwMsgBoxCtrl

A program error occurred.

Restart both the server PC and client PC

49498 FFVwMsgBoxCtrl

A program error occurred.

Restart both the server PC and client PC

%1=Error code

49499 VwMsgBoxCtrl 49499 FFVwMsgBoxCtrl

An exception error occurred. This error was detected in the Try/Catch or OnErrorGoto sequence. A program error occurred.

Restart the system. Contact the support center. Restart both the server PC and client PC %1=Error code %2=Details of an error

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-244

Appx MT1-245
Event Event Source Description
ErrorCode: %1 SubSystem: VI SourceFile: %2 SpotCode: %3 Exception Error occurred. %4 %5 Logical Program Error. %n %1 %n %2

Causes
A program error occurred.

Remedies
Restart both the server PC and client PC

Remarks
%1=Error code %2=Source, Function name %3=Spot code %4=Detailed code of an error %5=Details of an error

49499 FFVwMsgBoxCtrl

49500 FFMaRetrieve

A program error occurred.

Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Restart the system. Contact the support center. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Restart the system. Contact the support center. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Restart the system. Contact the support center. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Restart the system. Contact the support center. Delete unnecessary files to increase free disk space. Restart the system. Contact the support center. This is the acquisition subsystem startup time information for event log analysis. This is the acquisition subsystem startup time information for event log analysis.

49501 QAManagerCom 49501 FFMaRetrieve

Error about FilmOutFormat (50F1,XX10). Catch Exception Error. %n %1 %n %2

Program error. An exception error occurred.

49502 QAManagerCom 49502 FFMaRetrieve

Error about ImagePosition (2020,0010). Out Of Memory Error. %n %1 %n %2

Program error. Memory allocation failed.

49503 QAManagerCom 49503 FFMaRetrieve

Error about NumberOfCopies (2000,0010). Free Memory Error. %n %1 %n %2

Program error. Memory deallocation failed.

49504 QAManagerCom 49504 FFMaRetrieve 49505 QAManagerCom 49510 FFMaRetrieve 49511 FFMaRetrieve

Error about NumberOfImages (2011,XXA0). Disk Full Error. %n %1 %n %2 Error about Status (0007,F030). Retrieve Process Start. %n %1 %n %2 Retrieve Process End. %n %1 %n %2

Program error. The built-in hard disk does not have a sufficient free space. Program error. This is the information for event log analysis. This is the information for event log analysis.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-245

Appx MT1-246
Event Event Source Description
Process Communication Error. %n %1 %n %2

Causes
An error occurred in the communication control.

Remedies
The startup process was improperly performed, or the preceding process was not normally ended. If the same error recurs, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. The startup process was improperly performed, or the preceding process was not normally ended. If the same error recurs, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. With the Service Utility, check the network settings for the local equipment.

Remarks

49540 FFMaRetrieve

49541 FFMaRetrieve

Retrieve Process Exists. %n %1 %n %2

An attempt was made to run more than one acquisition process. It is conceivable that the preceding process was not normally ended.

49542 FFMaRetrieve 49543 FFMaRetrieve

Cannot Get NetWork Setting. %n %1 %n %2 Image is Already Exists in ImageDB. %n %1 %n %2 File Error. %n %1 %n %2

The network settings for the local equipment could not be acquired.

The input image was not stored because it Confirm the situation in which the error was the same as a stored one. occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. An attempt to access a file failed. Increase the amount of free space by installing an additional hard disk or by deleting unnecessary files. If it does not help, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Check the network connection to the transmitting end. If the network connection is normal, the timeout time might be too short. Increase the timeout time setting for network setup.

49544 FFMaRetrieve

49545 FFMaRetrieve

NetWork Error. %n %1 %n %2

A network error occurred.

49546 FFMaRetrieve 49547 FFMaRetrieve

Cannot Get NetWork Setting. %n %1 %n %2 DICOM Retrieve Timeout. %n %1 %n %2

Network settings cannot be acquired. A timeout occurred. Check the connection to the acquisition destination server and then try again to achieve acquisition. It the same error recurs, increase the acquisition timeout setting.

49548 FFMaRetrieve 49549 FFMaRetrieve

DICOM Retrieve is Not Able to Use Now. %n %1 %n %2 Processing Image is Deleted. %n %1 %n %2

The function for acquiring an image from a The setting for DICOM acquisition is not DICOM device is not available. adequate. Check the network settings. Processing is disabled because the image was deleted.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-246

Appx MT1-247
Event Event Source Description
Integration Warning in DataBase. %n %1 %n %2 DICOM Data Waring. %n %1 %n %2 Local Retrieve Warning. %n %1 %n %2 Input Image Warning (DensityCode = SH). %n %1 %n %2 Image is Already Exists in ImageDB. %n %1 %n %2 Retrieve Warnnig. %n %1 %n %2 [49573] Study data import was canceled. *The system is being terminated. Input of the study transmitted from DICOM Device was canceled. *Re-transmit the study from DICOM Device after the system has been started. 49575 FFCustomMsgBox [49575] The input study is either being modified or executed. *The input study is either being modified or executed. Input of the study was canceled. *Re-transmit the study from DICOM Device after a while. 49700 FFMaSetting Logical Program Error. %n %1 %n %2 A program error occurred.

Causes
The database is inconsistent. An image acquisition request for a DICOM device is generated.

Remedies

Remarks

49550 FFMaRetrieve 49551 FFMaRetrieve 49552 FFMaRetrieve 49553 FFMaRetrieve 49554 FFMaRetrieve 49555 FFMaRetrieve 49573 FFCustomMsgBox

This does not constitute a failure.

A request for acquiring an image within the This does not constitute a failure. local equipment is generated. An SH image was input. The entered image is the same as that is stored in the local equipment. An improper operation might have been performed during an acquisition process. As the system is terminating, the study input sent from the DICOM device was canceled. This does not constitute a failure. SH images are not supported. This does not constitute a failure. The displayed information merely indicates that the same image exists. This does not constitute a failure. Retry the operation after the system has been started.

As the study input is being modified or executed, the study input was canceled.

Retry the operation. If the problem is not resolved, restart the server application and client application.

Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

49701 FFMaSetting

Catch Exception Error. %n %1 %n %2

An exception error occurred.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-247

Appx MT1-248
Event Event Source Description
Out Of Memory Error. %n %1 %n %2

Causes
Memory allocation failed.

Remedies
Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Delete unnecessary files to increase free disk space. Obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

Remarks

49702 FFMaSetting

49703 FFMaSetting

Free Memory Error. %n %1 %n %2

Memory deallocation failed.

49704 FFMaSetting 49740 FFMaSetting

Disk Full Error. %n %1 %n %2 Variant Type Invalid. %n %1 %n %2

The built-in hard disk does not have a sufficient free space. The VARIANT data that is set for property setup is null, is not an array, or is of an incorrect array element type. It is highly probable that the program is faulty.

49741 FFMaSetting

Invalid Variant Element Count. %n The VARIANT data that is set for property Obtain the maintenance log with the %1 %n %2 setup has an incorrect array element count. Backup Utility, and send the maintenance log and an error report to the manufacturer. It is highly probable that the program is faulty. Get Recordset Failed. %n %1 %n %2 An abnormal return value was delivered from the record set acquisition common module. The SQL server is abnormal. Check whether the SQL server is running. If it is running, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Perform a reinstallation. If the same error recurs after the reinstallation, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Check whether the SQL server is running. If it is running, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

49742 FFMaSetting

49743 FFMaSetting

Get Connect String Failed. %n %1 %n %2

The setting information was not successfully acquired. This error is highly attributable to improper environment settings. An error occurred when an attempt was made to acquire a record set from a database. The SQL server is abnormal.

49744 FFMaSetting

Open Recordset Failed. %n %1 %n %2

49745 FFMaSetting

No Record Found In BodyParts. %n %1 %n %2

No data was found in the anatomical region Perform a reinstallation. If the reinstallation LoadInitialView code table. The database might be faulty. does not help, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-248

Appx MT1-249
Event Event Source Description
Convert to String Failed. %n %1 %n %2

Causes
An abnormality occurred during character string conversion. The database might be faulty.

Remedies

Remarks

49746 FFMaSetting

Perform a reinstallation. If the reinstallation GetCadAllItem, GetStudyBarItem does not help, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

49747 FFMaSetting 49748 FFMaSetting

Address Parameter Imvalid. %n %1 %n %2 PartsView Associated With Specified PartsCode Not Found. %n %1 %n %2 No Record Found In InitView. %n %1 %n %2

An error occurred when an attempt was Obtain the maintenance log with the made to return a property value. It is highly Backup Utility, and send the maintenance probable that the program is faulty. log and an error report to the manufacturer. Obtain the maintenance log with the GetInitialViewByBPE No data was found in the initial display setup table for various anatomical regions. Backup Utility, and send the maintenance This error is highly attributable to a log and an error report to the manufacturer. program fault. No data was found in the initial display setup table. The database might be faulty. Perform a reinstallation. If the reinstallation LoadInitialView does not help, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

49749 FFMaSetting

49750 FFMaSetting

No Record Found In StudyWndPtn. %n %1 %n %2

No data was found in the study window Perform a reinstallation. If the reinstallation LoadInitialView pattern setup table. The database might be does not help, confirm the situation in faulty. which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. No data was found in the initial display Perform a reinstallation. If the reinstallation LoadInitialView setup table for various anatomical regions. does not help, confirm the situation in The database might be faulty. which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. No data was found in the anatomical region Perform a reinstallation. If the reinstallation LoadInitialView sequence setup table. The database might does not help, confirm the situation in be faulty. which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. The exposure menu table data for the Obtain the maintenance log with the ReadExposeMenuOrder specified anatomical region was not found. Backup Utility, and send the maintenance This error is highly attributable to a log and an error report to the manufacturer. program fault. No data was found in the CAD sequence setup table. The database might be faulty. Perform a reinstallation. If the reinstallation LoadMammoCad does not help, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

49752 FFMaSetting

No Record Found In PartsView. %n %1 %n %2

49753 FFMaSetting

No Record Found In PartsOrder. %n %1 %n %2

49754 FFMaSetting

No Record Found In ExposureMenu. %n %1 %n %2 No Record Found In CadViewOrder. %n %1 %n %2

49756 FFMaSetting

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-249

Appx MT1-250
Event Event Source Description
No Record Found In MammoCadView. %n %1 %n %2

Causes

Remedies

Remarks

49757 FFMaSetting

No data was found in the CAD setup table. Perform a reinstallation. If the reinstallation LoadMammoCad The database might be faulty. does not help, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. A warning message indicating that the image information display item table data for the specified conditions was not found. The database might be faulty. Perform a reinstallation. If the reinstallation GetImageInfoItemLT, GetImageInfoItemRT, does not help, confirm the situation in GetImageInfoItemLB, GetImageInfoItemRT which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

49758 FFMaSetting

Overlay Item Associated With Specified Location And ImageType Not Found. %n %1 %n %2 Preset Parameter Associated With Specified PresetID Or PartsCode Not Found. %n %1 %n %2

49759 FFMaSetting

The preset parameter data for the specified Obtain the maintenance log with the ReadPresetParam, WritePresetParam conditions was not found. Backup Utility, and send the maintenance This error is highly attributable to a log and an error report to the manufacturer. program fault. Obtain the maintenance log with the ReadCadParam Backup Utility, and send the maintenance log and an error report to the manufacturer. Obtain the maintenance log with the SavePresetParam, MpmToPartsCode Backup Utility, and send the maintenance log and an error report to the manufacturer. ReadPresetParamName Obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Obtain the maintenance log with the Insert, Rename, SavePresetParam Backup Utility, and send the maintenance log and an error report to the manufacturer. Perform a reinstallation. If the reinstallation LoadStudyBarItem does not help, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

49760 FFMaSetting

CAD Parameter Associated With The image processing parameter data for Specified Purpose Not Found. %n the specified conditions was not found. %1 %n %2 This error is highly attributable to a program fault. Specified MPM Code Invalid. %n %1 %n %2 Specified Preset Name Not Exist. %n %1 %n %2 Specified Preset Name Already Exist. %n %1 %n %2 No Record Found In StudyBarItem. %n %1 %n %2 The specified MPM code could not be converted to an anatomical region code. This error is highly attributable to a faulty program. An attempt was made to update a nonexistent parameter preset name. This error is highly attributable to a faulty program. An attempt was made to add or switch to an existing parameter preset name. This error is highly attributable to a program fault. No data was found in the study window display item table. The database might be faulty.

49761 FFMaSetting

49762 FFMaSetting

49763 FFMaSetting

49764 FFMaSetting

49765 FFMaSetting

No Record Found In OverlayItem. No data was found in the image information Perform a reinstallation. If the reinstallation LoadOverlayItem %n display item table. does not help, confirm the situation in %1 %n %2 The database might be faulty. which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-250

Appx MT1-251
Event Event Source Description
Parameter Range Invalid. %n %1 %n %2 No Record Found In CadSensitivity. %n %1 %n %2

Causes

Remedies

Remarks

49766 FFMaSetting 49767 FFMaSetting

The argument value passed to the method Obtain the maintenance log with the was out of range. It is highly probable that Backup Utility, and send the maintenance the program is faulty. log and an error report to the manufacturer. No data was found in the CAD target menu. The database might be faulty. Perform a reinstallation. If the reinstallation GetCadSensitivity does not help, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. LoadInitialView Check whether the SQL server is running. FinalConstruct If it is running, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Check whether the SQL server is running. FinalRelease If it is running, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Check the amount of memory used by the system. If there is no problem with memory use, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Check the amount of memory used by the CopyVectorToVariant, system. If there is no problem with memory CopyVariantToVector use, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Check the amount of memory used by the system. If there is no problem with memory use, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

49768 FFMaSetting 49769 FFMaSetting

No Record Found In ImageWndPtn. %n %1 %n %2

The data was not found in the image window pattern setup table. The database might be faulty.

ADO Open Connection Failed. %n An attempt to connect the database failed. %1 %n %2 The database is abnormal.

49770 FFMaSetting

ADO Close Connection Failed. %n %1 %n %2

An attempt to disconnect the database failed. This problem is attributable to a database abnormality or a program error.

49771 FFMaSetting

Get Property Failed. %n %1 %n %2

The VARIANT data was not successfully referenced.

49772 FFMaSetting

SafeArray Operation Failed. %n %1 %n %2

The VARIANT data array conversion process was not successfully performed.

49773 FFMaSetting

Put Property Failed. %n %1 %n %2

The VARIANT data was not successfully set.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-251

Appx MT1-252
Event Event Source Description
DB Access Failed. %n %1 %n %2

Causes
The database was not successfully operated. The database is abnormal.

Remedies
Check whether the SQL server is running. If it is running, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer.

Remarks

49774 FFMaSetting

49775 FFMaSetting

Image Param Control Failed. %n %1 %n %2

An error occurred in an image processing parameter management component. This error is highly attributable to improper environment setup. The VARIANT data used to update the database was improperly sized. It is highly probable that the program is faulty.

Perform a reinstallation. If the same error LoadPresetParam recurs after the reinstallation, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Obtain the maintenance log with the WritePartsOrder, WriteExposeMenuOrder Backup Utility, and send the maintenance log and an error report to the manufacturer. GetRecordset

49776 FFMaSetting 49777 FFMaSetting 49778 FFMaSetting

Update Data Invalid. %n %1 %n %2 No Data In Recordset. %n %1 %n %2 Get Field Information Failed. %n %1 %n %2

This is a warning message indicating that a There is no particular problem. database record could not be acquired. The field information about a record set was not successfully acquired. This event is attributable to an insufficient memory or program error. An error was returned from the MPM code conversion module. It is highly probable that the program is faulty. An error was returned from the language acquisition (GetLanguage) module. The database might be faulty.

If there is no problem with the amount of GetFieldInfo memory use, confirm the situation in which the event occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an event report to the manufacturer. Obtain the maintenance log with the ReadPresetParamName Backup Utility, and send the maintenance log and an error report to the manufacturer. Perform a reinstallation. If the reinstallation CIPartsMenuOrder::FinalConstruct does not help, confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. This event will not be displayed in the event log. This event will not be displayed in the event log. This event will not be displayed in the event log. Setup dialog Setup dialog Setup dialog

49779 FFMaSetting 49780 FFMaSetting

Convert to PartsCode from MPM Failed. %n %1 %n %2 Get Language from SysConfig Failed. %n %1 %n %2

49781 FFMaSetting 49782 FFMaSetting 49783 FFMaSetting 49784 FFMaSetting

Set Value Range Invalid. %n %1 %n %2 Set Value Type Invalid. %n %1 %n %2 CAD Display Image Total Over Max. %n %1 %n %2 Infomation Setting Size Warning. %n %1 %n %2

This event will not be displayed in the event log. This event will not be displayed in the event log. This event will not be displayed in the event log. The image information area setup size is improper. The information cannot be entirely displayed because a small area is set from the Service Utility.

Check whether an improper display area is UserUtility: Incidental information set from the Service Utility.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-252

Appx MT1-253
Event Event Source Description
Create DDOFile Error.

Causes
DDO file generation failed.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

49900 FFMaRetrieve

49901 FFMaRetrieve

Write DDOFile Error.

A write process was not successfully performed for a DDO file.

49902 FFMaRetrieve

Get ImageInfo Error.

Image information was not successfully acquired.

49903 FFMaRetrieve

Open XMLFile Error.

An XML file was not successfully opened.

49904 FFMaRetrieve

Close XMLFile Error.

An XML file was not successfully closed.

49905 FFMaRetrieve

Parse XMLFile Error.

An XML file was not successfully parsed.

49906 FFMaRetrieve

XMLFile Not Correct.

XML file information is illegal.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-253

Appx MT1-254
Event Event Source Description
Create UID Error.

Causes
An UID number issuance process failed.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

49907 FFMaRetrieve

49908 FFMaRetrieve

Create Instance Error.

The instance generation process was not successfully performed.

49909 FFMaRetrieve

Get SystemInfo Error.

The system setting information was not successfully acquired.

49910 FFMaRetrieve

Input DDOFile Error.

A DDO file addition process failed.

49911

FFMaRetrieve

Program Error.

A program error occurred.

49999 ViClientInfoAccess

ErrorCode:%1%nSubSystem:%2 An exception error occurred. %nSourceFile:%3%nSpotCode:% 4%n Comment

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

50000 FFOutImgPrc 50001 FFCustomMsgBox

Initialize Error.%n%1 Failed in initialization processing.

An abnormality was encountered during initialization. The system was unstable.

Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-254

Appx MT1-255
Event Event Source Description
Initialize Error.%n[%1]

Causes
Initialization process error. Output control was not exercised. The error check method was not successfully called. A certain other program error occurred. An abnormality occurred in the connection to a database.

Remedies
Restart. If the same symptom frequently occurs, perform a reinstallation.

Remarks
Output section container.

50001 FFOUTPUT

50001 FFOutImgPrc

DB Connect Error.%n%1

Check whether the SQL service manager is normally operating. If the symptom occurs while the SQL service manager is normally operating, initialize the image database (the entire image data is then deleted). Restart. If the same symptom frequently occurs, perform a reinstallation. Output section container.

50001 Spooler

Initialize Error.%n[%1]

Initialization process error. Output control was not exercised. The error check method was not successfully called. A certain other program error occurred. The system was unstable.

50002 FFCustomMsgBox 50002 FFOUTPUT

Failed in output process. State Change Error.%n[%1]

Restart. If the same symptom recurs, perform a reinstallation. Output section container.

State change notification process error. Restart. An output destination was not successfully registered. A state change notification call was not successful. Other program error. Line establishment message transmission error Line abnormality message transmission error The database information is abnormal. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

50002 FFOutImgPrc 50002 Spooler

DB Infomation Error.%n%1 State Change Error.%n[%1]

Restart. State change notification process error. An output destination was not successfully registered. A state change notification call was not successful. Other program error. Line establishment message transmission error Line abnormality message transmission error The system was unstable. Restart. If the same symptom recurs, perform a reinstallation. Restart. The system was unstable. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

Output section container.

50003 FFCustomMsgBox 50003 FFOUTPUT 50003 FFOutImgPrc

Failed in output process. Routine Change Error.%n[%1] System Error.%n%1

Output section container.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-255

Appx MT1-256
Event Event Source Description
Routine Change Error.%n[%1] Failed in output process. Spool Error.%n[%1] The system was unstable.

Causes
Restart.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
Output section container.

50003 Spooler 50004 FFCustomMsgBox 50004 FFOUTPUT

Spool process error. Restart. The spool request call was not successfully made. The reoutput request was not successfully made. The study termination notification was not successfully made. The spool request response status was invalid. An unknown program error occurred. An interface abnormality was encountered. Restart. Spool process error. Restart. The spool request call was not successfully made. The reoutput request was not successfully made. The study termination notification was not successfully made. The spool request response status was invalid. An unknown program error occurred. The system was unstable. Forced-output process error. The spool forced output request call was not successfully made. The queue forced output response message was not successfully transmitted. An unknown program error occurred. File mapping was unachievable. Forced-output process error. The spool forced output request call was not successfully made. The queue forced output response message was not successfully transmitted. An unknown program error occurred. The system was unstable. Restart. If the same symptom recurs, perform a reinstallation. Restart.

Output section container.

50004 FFOutImgPrc 50004 Spooler

I/F Timing Error.%n%1 Spool Error.%n[%1]

Output section container.

50005 FFCustomMsgBox 50005 FFOUTPUT

Failed in output process. ExeOutput Error.%n[%1]

Output section container.

50005 FFOutImgPrc 50005 Spooler

CreateFileMapping Error.%n%1 ExeOutput Error.%n[%1]

Restart. Restart. Output section container.

50006 FFCustomMsgBox

Failed in output process.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-256

Appx MT1-257
Event Event Source Description
Image Proc Error.%n[%1]

Causes
Image processing error. The image processing request call was not successfully made. The image processing setup completion call was not successfully made. The image processing completion notification call was not successfully made. The image processing job acquisition request was not successfully made. An unknown program error occurred. The file could not be opened. A utility transition process error occurred. A utility transition request call failed. A utility transition response message was not successfully transmitted. Other program error. The system was unstable. Output processing error. The output destination information was not successfully acquired. The output request call was not successfully made. The output completion notification was not successfully made. An unknown program error occurred. The file was not successfully written/read. The disk might be faulty. Termination process error. Other program error. The system was unstable. Commitment processing error. The commitment destination information was not successfully acquired. The commitment request call was not successfully made. The commitment completion notification was not successfully made. An unknown program error occurred. Restart.

Remedies

Remarks
Output section container.

50006 FFOUTPUT

50006 FFOutImgPrc 50006 Spooler

File Open Error.%n%1 Utility Request Error.%n[%1]

Check the file. Output section container.

50007 FFCustomMsgBox 50007 FFOUTPUT

Failed in terminating process. Output Proc Error.%n[%1]

Restart. If the same symptom recurs, perform a reinstallation. Restart. Output section container.

50007 FFOutImgPrc 50007 Spooler 50008 FFCustomMsgBox 50008 FFOUTPUT

File Read/Write Error.%n%1 Terminate Error.%n[%1] Failed in image processing for output. Commit Proc Error.%n[%1]

If the error occurs frequently, replace the disk or take other remedial action. Restart. Restart. If the same symptom recurs, perform a reinstallation. Restart. Output section container. Output section container.

50008 FFOutImgPrc

CreateDispatch Error.%n%1

The control was not successfully initialized. Check that the control is registered.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-257

Appx MT1-258
Event Event Source Description
Image Proc Error.%n[%1]

Causes
Image process error. Restart. An image process request was not successfully called. An image process setup completion call was not successfully made. An image process completion notification was not successfully called. An image process job acquisition request was not successfully issued. Other program error. The system was unstable. Queue resumption process error. The queue resumption request call was not successfully made. The queue resumption response message was not successfully transmitted. An unknown program error occurred. The system was abnormal (memory allocation was not achieved). Output processing error. The output destination information was not successfully acquired. The output request call was not successfully made. The output completion notification was not successfully made. An unknown program error occurred. Queue resumption process error. A queue resumption request was not successfully called. A queue resumption response message was not successfully transmitted. Other program error. The system was abnormal (memory allocation was not achieved). Queue resumption process error. The queue resumption request call was not successfully made. The queue resumption response message was not successfully transmitted. An unknown program error occurred.

Remedies

Remarks
Output section container.

50008 Spooler

50009 FFCustomMsgBox 50009 FFOUTPUT

Failed in output process. Queue Resume Error.%n[%1]

Restart. If the same symptom recurs, perform a reinstallation. Restart. Output section container.

50009 FFOutImgPrc 50009 Spooler

Memory Get Error.%n%1 Output Proc Error.%n[%1]

Restart. Restart. Output section container.

50010 FFOUTPUT

Queue Delete Error.%n[%1]

Restart.

Output section container.

50010 FFOutImgPrc 50010 Spooler

Memory (DDO) Get Error.%n%1 Queue Resume Error.%n[%1]

Restart. Restart. Output section container.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-258

Appx MT1-259
Event
50011

Event Source
FFOUTPUT

Description
Unit Suspend Error.%n[%1]

Causes
Equipment output suspension process error. The equipment output suspension request call was not successfully made. The equipment output suspension response message was not successfully transmitted. An unknown program error occurred. The system was abnormal (memory allocation was not achieved). Queue resumption process error. A queue resumption request was not successfully called. A queue resumption response message was not successfully transmitted. Other program error. Restart.

Remedies

Remarks
Output section container.

50011 50011

FFOutImgPrc Spooler

Memory (VR) Get Error.%n%1 Queue Delete Error.%n[%1]

Restart. Restart. Output section container.

50012 FFOUTPUT

Unit Resume Error.%n[%1]

Equipment output resumption error. Restart. The equipment output resumption request call was not successfully made. The equipment output resumption response message was not successfully transmitted. An unknown program error occurred. The Dicom Data Object is abnormal. Equipment output suspension process error. The equipment output suspension request call was not successfully made. The equipment output suspension response message was not successfully transmitted. An unknown program error occurred. Queue priority change error. No information was found in the Dicom Data Object. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart.

Output section container.

50012 FFOutImgPrc 50012 Spooler

Dicom Data Object Error.%n%1 Unit Suspend Error.%n[%1]

Output section container.

50013 FFOUTPUT 50013 FFOutImgPrc 50013 Spooler

Priority Change Error.%n[%1] Dicom Data Object No Data.%n%1 Unit Resume Error.%n[%1]

Output section container.

Restart. Equipment output resumption error. The equipment output resumption request call was not successfully made. The equipment output resumption response message was not successfully transmitted. An unknown program error occurred.

Output section container.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-259

Appx MT1-260
Event Event Source Description
Utility Request Error.%n[%1]

Causes
A utility transition process error occurred. A utility transition request call failed. A utility transition response message was not successfully transmitted. Other program error. Termination process error. Other program error. A data abnormality was encountered. The output database is abnormal. A memory region error occurred. An abnormality occurred. The format calculation object was abnormal. Common error message. Queue information class related message. An output job file was not successfully accessed. Output job information was not successfully accessed. Film information was not successfully acquired. Information was not successfully acquired. The job status was not successfully acquired (program error). Job information was not successfully freed. Unit information class related message. Unit information was not successfully freed. Spooler class related message. The film count was not successfully checked. The image count/image information area was not successfully acquired. Unit information was not successfully acquired. Other program error Restart.

Remedies

Remarks
Output section container.

50014 FFOUTPUT

50015 FFOUTPUT 50020 FFOutImgPrc 50021 FFOutImgPrc 50022 FFOutImgPrc 50030 FFOutImgPrc 50100 FFOutImgPrc 50100 Spooler

Terminate Error.%n[%1] Data Error.%n%1 Output Job DB Error.%n%1 Memory Over.%n%1 OutImgPrc Error.%n%1 IFormatCom Error.%n%1 Spooler Error.%n%1

Output section container.

Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. Restart. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Spooler

50100 FFCustomMsgBox 50101 FFOutImgPrc

Disk storing failed. IRawMakeCom Error.%n%1

Contact your service engineer. A RAW data creation object was abnormal. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-260

Appx MT1-261
Event Event Source Description
RunProc Error.%n%1

Causes
Initialization process error. The spooler control state was abnormal. A spool start process was in error. A database connection was not successfully closed. Other program error. An abnormality occurred at the time of network setup data acquisition. (It is conceivable that the network setup database was abnormal.)

Remedies
Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Spooler

Remarks

50101 Spooler

50101 FFCustomMsgBox 50102 FFOutImgPrc

Disk storing failed. FFNetDB Error.%n%1

Contact your service engineer. Restart. If the same symptom frequently occurs, perform a reinstallation. Spooler

50102 Spooler

OutputRegisterProc Error.%n%1

Output destination registration process Restart. If the same symptom frequently error. occurs, perform a reinstallation and then The spooler control state was abnormal. initialize the image database. An illegal parameter was encountered. An output destination registration request message was not successfully issued. An output destination was not successfully registered. Other program error. Contact your service engineer. The decompression object was abnormal. Local printer/Dicom printer state change notification process error. The spooler control state was abnormal. An illegal parameter was encountered. A printer state change notification message was not successfully issued. The unit status was not successfully acquired. Other program error. The normalization process object was abnormal. Data integrity check process error. The spooler control state was abnormal. A data integrity check request message was not successfully issued. Other program error. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

50102 FFCustomMsgBox 50103 FFOutImgPrc 50103 Spooler

Disk storing failed. IImgJpegCtrl Error.%n%1 StateChangeProc Error.%n%1

Spooler

50104 FFOutImgPrc 50104 Spooler

IFMImgSkGpCtrl Error.%n%1 ErrorCheckProc Error.%n%1

Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Contact your service engineer. Spooler

50104 FFCustomMsgBox

Disk storing failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-261

Appx MT1-262
Event Event Source Description
IFMImgVRSCtrl Error.%n%1 RestoreJob Error.%n%1

Causes
The zoom object (VRS method) was abnormal. Job restoration error. The spooler control state was abnormal. An unprocessed job restoration request message was not successfully issued. Other program error. The rotation object was abnormal.

Remedies
Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Spooler Spooler

Remarks

50105 FFOutImgPrc 50105 Spooler

50106 FFOutImgPrc 50106 Spooler

IRotateCom Error.%n%1 SpoolProc Error.%n%1

Spool process error. Restart. If the same symptom frequently The spooler control state was abnormal. occurs, perform a reinstallation and then initialize the image database. A parameter error occurred. A spool request message was not successfully issued. DDO file information was not successfully acquired. Other program error. Contact your service engineer. The image process management parameter object was abnormal. Reoutput start process error. The spooler control state was abnormal. An illegal parameter was encountered. A reoutput start message was not successfully issued. Other program error. An abnormal CR image processing object was encountered. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

50106 FFCustomMsgBox 50107 FFOutImgPrc 50107 Spooler

Disk storing failed. IFMImgParamCtrl Error.%n%1 ReoutputProc Error.%n%1

Spooler

50108 FFOutImgPrc 50108 Spooler

IFMImgHandCtrl Error.%n%1 StudyReqEndProc Error.%n%1

Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Spooler

Study termination request processing error. Restart. If the same symptom frequently occurs, perform a reinstallation and then Spooler control status error. initialize the image database. Illegal parameters. Failed in issuing study termination request message. Other program errors. FCR compression (compression/ decompression (Fujis unique method)) was abnormal. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

50109 FFOutImgPrc

IFMImgFCmpCtrl Error.%n%1

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-262

Appx MT1-263
Event Event Source Description
ExeOutputJob Error.%n%1

Causes

Remedies
Spooler

Remarks

50109 Spooler

Forced output request process error. Restart. If the same symptom frequently The spooler control state was abnormal. occurs, perform a reinstallation and then initialize the image database. An illegal parameter was encountered. A forced output request message was not successfully issued. The requested output image data did not exist. Other program error. Data conversion (for DICOM) was abnormal. Image processing job acquisition process error. The spooler control state was abnormal. An image processing job acquisition request message was not successfully issued. Data was not databased. Other program error. Data conversion (for DICOM Storage) was abnormal. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

50110 50110

FFOutImgPrc Spooler

IDataToPrintCom Error.%n%1 GetImageProcJob Error.%n%1

Spooler

50111 50111

FFOutImgPrc Spooler

IDataToStorageCom Error.%n%1 SetImageProcComplete Error.%n%1

Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Spooler

Image processing completion notification Restart. If the same symptom frequently process error. occurs, perform a reinstallation and then The spooler control state was abnormal. initialize the image database. An illegal parameter was encountered. An image processing completion notification message was not successfully issued. Other program error. Moire removal failed. Output job acquisition response process error. The spooler control state was abnormal. An output job acquisition response message was not successfully issued. Data was not databased. Other program error. The film annotation character generation object was abnormal. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

50112 50112

FFOutImgPrc Spooler

IFMImgMoireCtrl Error.%n%1 GetOutputProcJob Error.%n%1

Spooler

50113

FFOutImgPrc

IFilmCharMakeCom Error.%n%1

Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-263

Appx MT1-264
Event
50113

Event Source
Spooler

Description
SetOutputProcComplete Error.%n%1

Causes
Output completion notification process error. The spooler control state was abnormal. An illegal parameter was encountered. An output completion notification message was not successfully issued. Data was not databased. Other program error. The blackening process was abnormal.

Remedies
Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Spooler

Remarks

50113 50114 50114

FFCustomMsgBox FFOutImgPrc Spooler

Disk storing failed. MaskProcExec Error.%n%1 GetCommitProcJob Error.%n%1

Contact your service engineer. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Output image processing control Spooler

Commitment job acquisition response Restart. If the same symptom frequently process error. occurs, perform a reinstallation and then The spooler control status was abnormal. initialize the image database. The commitment jog acquisition response message was not successfully issued. The data was not found in the database. An unknown program error occurred. Queue output pause request process error. Abnormal spooler control status. Illegal parameter. Unsuccessful queue output pause request message issuance. Other program error. The blackening automatic recognition process was abnormal. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

50114

Spooler

QueueSuspend Error.%n%1

Spooler

50115 50115

FFOutImgPrc Spooler

RecognizeProcExec Error.%n%1 SetCommitProcComplete Error.%n%1

Output image processing control Spooler

Commitment completion notification Restart. If the same symptom frequently process error. occurs, perform a reinstallation and then The spooler control status was abnormal. initialize the image database. An illegal parameter was encountered. The commitment completion notification message was not successfully issued. The queue was not found. The data was not found in the database. An unknown program error occurred. Queue output resumption request process error. The spooler control state was abnormal. An illegal parameter was encountered. A queue output resumption request message was not successfully issued. Other program error. The marker imbedding process was abnormal. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

50115

Spooler

QueueResume Error.%n%1

Spooler

50116

FFOutImgPrc

ExecMarker Error.%n%1

Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-264

Appx MT1-265
Event
50116

Event Source
Spooler

Description
QueueSuspend Error.%n%1

Causes
Queue output pause request process error. Abnormal spooler control status. Illegal parameter. Unsuccessful queue output pause request message issuance. Other program error. Queue deletion request process error. The spooler control state was abnormal. An illegal parameter was encountered. A queue deletion request message was not successfully issued. Output job file information was not successfully accessed. Queue deletion was not successful. Database access was not successful. Other program error. An abnormality occurred during a display gradation correction process. Queue output resumption request process error. The spooler control state was abnormal. An illegal parameter was encountered. A queue output resumption request message was not successfully issued. Other program error.

Remedies
Spooler

Remarks

50116

Spooler

QueueDelete Error.%n%1

Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

Spooler

50116 50117 50117

FFCustomMsgBox FFOutImgPrc Spooler

Disk storing failed. LUTProcExec Error.%n%1 QueueResume Error.%n%1

Contact your service engineer. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Spooler

50117

Spooler

UnitSuspend Error.%n%1

Queue output resumption request process Restart. If the same symptom frequently error. occurs, perform a reinstallation and then The spooler control status was abnormal. initialize the image database. An illegal parameter was encountered. The queue output resumption request message was not successfully issued. An unknown program error occurred. An error occurred in an output information conversion process. Queue deletion request process error. The spooler control state was abnormal. An illegal parameter was encountered. A queue deletion request message was not successfully issued. Output job file information was not successfully accessed. Queue deletion was not successful. Database access was not successful. Other program error. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

Spooler

50118 50118

FFOutImgPrc Spooler

MPMCode Error.%n%1 QueueDelete Error.%n%1

Spooler

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-265

Appx MT1-266
Event
50118

Event Source
Spooler

Description
UnitResume Error.%n%1

Causes
Unit resumption request process error. The spooler control state was abnormal. An illegal parameter was encountered. A unit resumption request message was not successfully issued. Other program error. An error occurred while in trimming processing.

Remedies
Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Spooler

Remarks

50119 50119

FFOutImgPrc Spooler

Trimming Error.%n%1 UnitSuspend Error.%n%1

Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Spooler

Queue output resumption request process Restart. If the same symptom frequently error. occurs, perform a reinstallation and then The spooler control status was abnormal. initialize the image database. An illegal parameter was encountered. The queue output resumption request message was not successfully issued. An unknown program error occurred. Equipment suspension request process Restart. If the same symptom frequently error. occurs, perform a reinstallation and then The spooler control status was abnormal. initialize the image database. The equipment suspension request message was not successfully issued. An unknown program error occurred. Contact your service engineer. An abnormality occurred during the Restart. If the same symptom frequently annotation information embedding process. occurs, perform a reinstallation and then initialize the image database. Unit resumption request process error. The spooler control state was abnormal. An illegal parameter was encountered. A unit resumption request message was not successfully issued. Other program error. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

50119

Spooler

SuspendProc Error.%n%1

Spooler

50119

FFCustomMsgBox

Disk storing failed. AnnotationProc Error.%n%1 UnitResume Error.%n%1

50120 FFOutImgPrc 50120 Spooler

Spooler

50120 Spooler

ResumeProc Error.%n%1

Equipment resumption request process Restart. If the same symptom frequently error. occurs, perform a reinstallation and then The spooler control status was abnormal. initialize the image database. The equipment resumption request message was not successfully issued. An unknown program error occurred. FNC Proc Error Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

Spooler

50121 FFOutImgPrc 50121 Spooler

FNCProc Error.%n%1 SuspendProc Error.%n%1

Equipment suspension request process Restart. If the same symptom frequently error. occurs, perform a reinstallation and then The spooler control status was abnormal. initialize the image database. The equipment suspension request message was not successfully issued. An unknown program error occurred.

Spooler

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-266

Appx MT1-267
Event Event Source Description
EndProc Error.%n%1

Causes
End request process error. The spooler control state was abnormal. An end request message was not successfully issued. Other program error.

Remedies
Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Contact your service engineer. Spooler

Remarks

50121 Spooler

50121 FFCustomMsgBox 50122 Spooler

Disk storing failed. ResumeProc Error.%n%1

Equipment resumption request process Restart. If the same symptom frequently error. occurs, perform a reinstallation and then The spooler control status was abnormal. initialize the image database. The equipment resumption request message was not successfully issued. An unknown program error occurred. Contact your service engineer. A DDO file was not successfully read. Restart. If the same symptom recurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Contact your service engineer. Data setup was not successfully performed Restart. If the same symptom recurs, for a DDO file. perform a reinstallation and then initialize the image database. Failed in storing the information file (DDO). Restart. If the same symptom recurs, perform a reinstallation and then initialize the image database. There is no HQ image file in the information Restart. If the same symptom recurs, file (DDO). perform a reinstallation and then initialize the image database. The number of image files was not successfully acquired. Restart. If the same symptom recurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom recurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom recurs, perform a reinstallation and then initialize the image database. Contact your service engineer.

Spooler

50122 FFCustomMsgBox 50122 FFOutImgPrc

Disk storing failed. ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode: %4%n Arbitrary Information Details. EndProc Error.%n%1

50123 Spooler

End request process error. The spooler control state was abnormal. An end request message was not successfully issued. Other program error.

Spooler

50123 FFCustomMsgBox 50123 FFOutImgPrc 50124 FFOutImgPrc 50125 FFOutImgPrc 50126 FFOutImgPrc 50127 FFOutImgPrc 50128 FFOutImgPrc 50129 FFCustomMsgBox

Disk storing failed. DICOM ReplaceVR/Push Error. SaveFile Error (%1) No Original Image File Name. Get Image File Number Error.

%1=File path

Get Original DDO FileName Error A DDO filename was not successfully : [%1] acquired. Get Output DDO FileName Error. Disk storing failed. The output DDO file name was not successfully acquired.

%1=File path

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-267

Appx MT1-268
Event Event Source Description
OutputJob Object Data Set (%1) Error FFGeneralImageProc.Initialize Error. File Copy Failed : [%1] -> [%2] Make Image File Failed. Make Output DDO File Failed. An attempt to output to C@Rna data center resulted in a failure. An attempt to output to C@Rna data center resulted in a failure. An attempt to output to C@Rna data center resulted in a failure. An attempt to output to C@Rna data center resulted in a failure. An attempt to output to C@Rna data center resulted in a failure. An attempt to output to C@Rna data center resulted in a failure. An attempt to output to C@Rna data center resulted in a failure. An attempt to output to C@Rna data center resulted in a failure. An attempt to output to C@Rna data center resulted in a failure. An attempt to output to C@Rna data center resulted in a failure. An attempt to output to C@Rna data center resulted in a failure. An attempt to output to C@Rna data center resulted in a failure. An attempt to output to C@Rna data center resulted in a failure. SetImgInf Error.%n%1 Information retrieval from DDO for reference failed.

Causes
File data setup failed. Component initialization failed. The file was unsuccessfully copied. Image file creation failed. The output DDO file was not successfully created.

Remedies
Restart. If the same symptom recurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Contact your service engineer. Contact your service engineer. Contact your service engineer. Contact your service engineer. Contact your service engineer. Contact your service engineer. Contact your service engineer. Contact your service engineer. Contact your service engineer. Contact your service engineer. Contact your service engineer. Contact your service engineer. Contact your service engineer. Restart both the server application and client application. If this situation should occur frequently, reinstall and initialize the image DB. %1=File path

Remarks

50129 FFOutImgPrc 50130 FFOutImgPrc 50131 FFOutImgPrc 50132 FFOutImgPrc 50133 FFOutImgPrc 50150 FFCustomMsgBox 50151 FFCustomMsgBox 50152 FFCustomMsgBox 50153 FFCustomMsgBox 50154 FFCustomMsgBox 50155 FFCustomMsgBox 50156 FFCustomMsgBox 50157 FFCustomMsgBox 50158 FFCustomMsgBox 50159 FFCustomMsgBox 50160 FFCustomMsgBox 50161 FFCustomMsgBox 50162 FFCustomMsgBox 50163 FFOutImgPrc

%1=Path of the source file for copying %2=Path of the target file for copying

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-268

Appx MT1-269
Event Event Source Description
[50200] Failed in output processing of JPEG/BMP file. > Contact your service engineer. [50201] Failed in output processing of JPEG/BMP file. > Contact your service engineer. [50202] Failed in output processing of JPEG/BMP file. > Contact your service engineer. [50203] Failed in output processing of JPEG/BMP file. > Contact your service engineer. [50204] Failed in output processing of JPEG/BMP file. > Contact your service engineer. [50205] Failed in the output of JPEG/BMP file. > Failed in gaining access to the folder to save. > Check the conditions of the folder to save. [50206] Failed in output processing of JPEG/BMP file. > Contact your service engineer. [50211] Failed in output processing of JPEG/BMP file. > The name of the output destination is invalid. + Contact your service engineer. [50212] Failed in output processing of JPEG/BMP file. > The name of the output destination is invalid. + Contact your service engineer. [50213] Failed in output processing of JPEG/BMP file. + Contact your service engineer. [50215] Failed in output processing of JPEG/BMP file. > The name of the output destination is invalid. + Contact your service engineer.

Causes
Just as the message states. Just as the message states. Just as the message states. Just as the message states. Just as the message states. Just as the message states.

Remedies

Remarks

50200 FFCustomMsgBox 50201 FFCustomMsgBox 50202 FFCustomMsgBox 50203 FFCustomMsgBox 50204 FFCustomMsgBox 50205 FFCustomMsgBox

50206 FFCustomMsgBox 50211 FFCustomMsgBox

Just as the message states. Just as the message states.

50212 FFCustomMsgBox

Just as the message states.

50213 FFCustomMsgBox 50215 FFCustomMsgBox

Just as the message states. Just as the message states.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-269

Appx MT1-270
Event Event Source Description
[50216] Failed in output processing of JPEG/BMP file. > The name of the output destination is invalid. + Contact your service engineer. A fatal error occurred. Failed in registering the following images. StudyInstanceUID : %s SOPInstanceUID : %s Data in the disk inserted into the drive for storage may have been broken. PDI Drive None Drive Select Error Media Eject Error Eject FALSE Download File None PDI output is disabled on this equipment. No disk drive could be recognized. The disk could not be removed. The disk could not be removed. There are no images for PDI output. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Causes
Just as the message states.

Remedies

Remarks

50216 FFCustomMsgBox

50600 FFCustomMsgBox 50604 FFCustomMsgBox

Contact your service engineer. Contact your service engineer.

50605 FFCustomMsgBox 50702 PDIWizard 50703 PDIWizard 50704 PDIWizard 50704 PDIWizard 50710 PDIWizard

Contact your service engineer. System settings may not have been performed correctly. Verify settings and reperform PDI output. Check to see that the disk drive is connected and retry to recognize disk drive. It is possible that the disk is being used. If so, reperform PDI output after the currently performed operation is finished.

50710 PDIWizard

Image File None

None of the images is available for PDI output.

50710 PDIWizard

GetUnicodeVR Error

Failed to capture image information from the images for PDI output.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-270

Appx MT1-271
Event Event Source Description
PDI Template Folder None

Causes
The is no template folder for PDI output.

Remedies
Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

50710 PDIWizard

50710 PDIWizard

OutImageProc Run Proc Err

Creation of a file targeted for PDI output failed.

50710 PDIWizard

OutImageProc ExecImageProc Err

Creation of a file targeted for PDI output failed.

50710 PDIWizard

OutputJob SetItem Err

Creation of a file targeted for PDI output failed.

50710 PDIWizard

OutImageProc ImageProc Err

Creation of a file targeted for PDI output failed.

50710 PDIWizard

DICOMStreamFile Create Error

Creation of a file targeted for PDI output failed.

50710 PDIWizard

MediaUID Create Error

Creation of a file targeted for PDI output failed.

50710 PDIWizard

DICOMDIR Create Start Error

Creation of a file targeted for PDI output failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-271

Appx MT1-272
Event Event Source Description
Modality Name Invalid Data is illegal.

Causes

Remedies
Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

50710 PDIWizard

50710 PDIWizard

FFDiskWriteCom Init Error

Component initialization failed.

50710 PDIWizard

Media Check Error

The inserted disk could not be checked.

50710 PDIWizard

Drive Eject Lock Error

The drive could not be locked.

50710 PDIWizard

Param Error

Data is illegal.

50710 PDIWizard

Get Server Name Error

An attempt to acquire server equipment name failed.

50710 PDIWizard

Get Caption Error

An attempt to acquire character strings to be displayed on the screen resulted in a failure.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-272

Appx MT1-273
Event Event Source Description
Get SystemInfo Error

Causes
An attempt to acquire system setup information resulted in a failure.

Remedies
Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Check to see that the disk drive is connected, and reperform the same processing.

Remarks

50710 PDIWizard

50710 PDIWizard

Get IPAddress Error

Acquisition of IP address resulted in a failure.

50710 PDIWizard

BG GetMutexl Error

An error occurred in an attempt to acquire exclusive right of the drive.

50750 PDIWizard

Initialize Error.

An error occurred during BsGOLD library initialization processing.

50751 PDIWizard

Terminate Error.

An error occurred during BsGOLD library termination processing.

50752 PDIWizard

GetMutex Error.

An error occurred in an attempt to acquire exclusive right of the drive.

50753 PDIWizard

FreeMutex Error.

An error occurred in an attempt to release exclusive right of the drive.

50754 PDIWizard

DecideDrive Error.

An error occurred during drive selection processing.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-273

Appx MT1-274
Event Event Source Description
GetMediaInfo Error.

Causes
An error occurred in an attempt to acquire disk information.

Remedies
Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

50755 PDIWizard

50756 PDIWizard 50757 PDIWizard 50578 PDIWizard

WriteMedia Error. Eject Error. EjectLock Error.

An error occurred when writing data onto a If another application is up and running, disk. shut it down and reperform data writing or restart the computer and then reperform it. The disk could not be removed. The drive could not be locked. It is possible that the disk is being used. If so, retry PDI output after the currently performed operation is finished. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

50579 PDIWizard

EjectUnLock Error.

An error occurred when unlocking the drive.

50760 PDIWizard

Program Error.

A program error occurred.

50800 FFCustomMsgBox

[50800] An error occurred by a free layout. *Check that the network cable is connected, and then execute again. Check that the server computer is started, and then execute again. >If the same symptom recurs even after performing the above, contact our service engineer.

An unknown error occurred.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-274

Appx MT1-275
Event Event Source Description Causes Remedies
Check that the network cable is connected and the server computer is started, and then retry the operation. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. There is no operational problem. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Free layout output file deletion processing has failed. Deletion of files or folders created with free layout failed. (If Read-only is checked, uncheck it.)

Remarks

50806 FFCustomMsgBox

[50806] Failed in film output of the It is possible that the network cable was Free Layout. not attached at the time of film output. *Check that the network cable is connected, and then execute again. Check that the server computer is started, and then execute again. >If the same symptom recurs even after performing the above, contact our service engineer.

50810 FreeLayout Communicator

The thread has already started.

A program error occurred.

50810 FreeLayout Communicator 50810 FreeLayout Communicator

Delete failed. A program error occurred. Exceptional error (message output by OS). Exceptional error (message output A program error occurred. by OS).

50810 FreeLayout Communicator 50811 FreeLayout Communicator

directory is already exists.

Already existing file name.

Exceptional error (message output A program error occurred. by OS).

50812 FreeLayout Communicator

CreatorIF.FLCRequest() failed.

A program error occurred.

A free layout print request has failed.

50813 FreeLayout Communicator

Thread(Id=, , Name= ) unknown Event=

An invalid event has been received.

50814 FreeLayout Communicator

Thread(Id=, , Name= ) strCmd= strsrc= strDest= strData=

An invalid event has been received.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-275

Appx MT1-276
Event Event Source Description
Thread(Id=, , Name= ) Rename Failed

Causes
A program error occurred.

Remedies
Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

50816 FreeLayout Communicator

50816 FreeLayout Communicator

Thread(Id=, , Name= ) PostMessage Failed

A program error occurred.

50816 FreeLayout Communicator

Thread(Id=, , Name= ) EndProcComplete notification Failed Thread(Id=, , Name= ) PostMessage Failed

A program error occurred.

50816 FreeLayout Communicator

A program error occurred.

50816 FreeLayout Communicator

Thread(Id=, , Name= ) DDOSetting Failed

A program error occurred.

50816 FreeLayout Communicator

Thread(Id=, , Name= ) Conversion Failed

A program error occurred.

50816 FreeLayout Communicator

Thread(Id=, , Name= ) OutImagePrc.RunProc() failed

A program error occurred.

50816 FreeLayout Communicator

Thread(Id=, , Name= ) new OutputJobComClass() failed

A program error occurred.

50816 FreeLayout Communicator

Thread(Id=, , Name= ) OutImagePrc.ExecImageProc failed

A program error occurred.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-276

Appx MT1-277
Event Event Source Description
Thread(Id=, , Name= ) new FFDicomObj.DicomObj() failed Thread(Id=, , Name= ) Image type judgment failed

Causes
A program error occurred.

Remedies
Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

50816 FreeLayout Communicator

50816 FreeLayout Communicator

A program error occurred.

50816 FreeLayout Communicator

Thread(Id=, , Name= ) DDO Tag Not Exist failed

A program error occurred.

50816 FreeLayout Communicator

Thread(Id=, , Name= ) DDO Data Length=0

A program error occurred.

50816 FreeLayout Communicator

Thread(Id=, , Name= ) Exception Error

A program error occurred.

50816 FreeLayout Communicator

Thread(Id=, , Name= ) RunProcComplete notification Failed Thread(Id=, , Name= ) PostMessage Failed

A program error occurred.

50816 FreeLayout Communicator

A program error occurred.

50816 FreeLayout Communicator

Thread(Id=, , Name= ) ImageProcComplete notification Failed Thread(Id=, , Name= ) AnnotationConversion Failed

A program error occurred.

An output image creation error has occurred.

50816 FreeLayout Communicator

A program error occurred.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-277

Appx MT1-278
Event Event Source Description
Thread(Id=, , Name= ) Error at Create Message Pipe.

Causes
A program error occurred.

Remedies
Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

50817 FreeLayout Communicator

50818 FreeLayout Communicator

StudySeq count error.

A program error occurred.

There is not even one study information set.

50818 FreeLayout Communicator

ExecuteSqlSelect error.

A program error occurred.

An exception has occurred with search of the study DB.

50818 FreeLayout Communicator

Exceptional error (message output A program error occurred. by OS).

50818 FreeLayout Communicator

DDOFile Not found error.

A program error occurred.

Setting of output information to DDO has failed.

50818 FreeLayout Communicator

ChangeUserIdToPersonName error.

A program error occurred.

PN conversion processing has failed.

50818 FreeLayout Communicator

FFNetDBConnect error.

A program error occurred.

Connection to NetConfigDB has failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-278

Appx MT1-279
Event Event Source Description
FFNetDBGetDeviceList error.

Causes
A program error occurred.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks
Device name retrieval has failed.

50818 FreeLayout Communicator

50818 FreeLayout Communicator

FFNetDBGetDicomAE error.

A program error occurred.

AE information retrieval (retrieval failed error).

50818 FreeLayout Communicator

FFNetDBGetDicomAE error. Not found.

A program error occurred.

AE information retrieval (not applicable).

50818 FreeLayout Communicator

FFNetDBGetDicomPrint error.

A program error occurred.

DicomPrint information retrieval has failed. Not applicable

50818 FreeLayout Communicator

FFNetDBClose error.

A program error occurred.

NetConfig disconnection has failed.

50818 FreeLayout Communicator

DDO Not found error.

A program error occurred.

The LUT file set to each device does not exist.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-279

Appx MT1-280
Event Event Source Description
FFGetString error.

Causes
A program error occurred.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks
Retrieval of the NetConfigDB connection text string from Directory.ini has failed.

50818 FreeLayout Communicator

50818 FreeLayout Communicator

FFNetDBGetSysDeviceID error.

A program error occurred.

Retrieval of an own system device ID has failed.

50818 FreeLayout Communicator

FFNetDBGetLUTFile error.

A program error occurred.

PresentationLUT retrieval has failed.

50818 FreeLayout Communicator

Fatal error.

A program error occurred.

Retrieval of the specified path information from Directory.ini has failed.

50818 FreeLayout Communicator

FFGetString error.( )

A program error occurred.

Retrieval of the specified path information from Directory.ini has failed.

50818 FreeLayout Communicator

GetLanguageValue error.

A program error occurred.

Language setting retrieval has failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-280

Appx MT1-281
Event Event Source Description
GetFormatInfo error.

Causes
A program error occurred.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks
Retrieval of the format setting from the system DB has failed.

50818 FreeLayout Communicator

50818 FreeLayout Communicator

GetFontInfo error.

A program error occurred.

Font setting retrieval has failed.

50818 FreeLayout Communicator

FFCreateUID error.

A program error occurred.

UID number creation has failed.

50818 FreeLayout Communicator

Get SystemInfo Error. (OutputResolution)

A program error occurred.

Retrieval of the output resolution for a non-FCR image has failed.

50818 FreeLayout Communicator

Get SystemInfo Error. (InstitutionName)

A program error occurred.

Institution name retrieval has failed.

50818 FreeLayout Communicator

Get SystemInfo Error. (FreeLayoutPatientIdFlag)

A program error occurred.

Retrieval of the free layout set value from the system settings DB has failed. (FreeLayoutPatientIdFlag)

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-281

Appx MT1-282
Event Event Source Description
Get SystemInfo Error. (FreeLayoutDiskSize)

Causes
A program error occurred.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks
Retrieval of the free layout set value from the system settings DB has failed. (FreeLayoutDiskSize)

50818 FreeLayout Communicator

50818 FreeLayout Communicator

Get SystemInfo Error. (MsgTableName)

A program error occurred.

Setting retrieval from the system settings DB has failed.

50818 FreeLayout Communicator

Get FontInfo Error.(Multibyte)

A program error occurred.

Retrieval of the multibyte use classification has failed.

50818 FreeLayout Communicator

Get FontInfo Error.(Font)

A program error occurred.

Retrieval of the font name has failed.

50818 FreeLayout Communicator

Get FontInfo Error.(FontSize)

A program error occurred.

Retrieval of the font size has failed.

50818 FreeLayout Communicator

Get FontInfo Error.(FontSizeS)

A program error occurred.

Retrieval of the font size S has failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-282

Appx MT1-283
Event Event Source Description
Get FontInfo Error.(FontSizeSS)

Causes
A program error occurred.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks
Retrieval of the font size SS has failed.

50818 FreeLayout Communicator

50818 FreeLayout Communicator

Get FontInfo Error.(FontSizeM)

A program error occurred.

Retrieval of the font size M has failed.

50818 FreeLayout Communicator

Get FontInfo Error.(FontSizeL)

A program error occurred.

Retrieval of the font size L has failed.

50818 FreeLayout Communicator

Get FontInfo Error.(FontSizeLL)

A program error occurred.

Retrieval of the font size LL has failed.

50818 FreeLayout Communicator

Get FontInfo Error. (FontSizeStudyWindowBar)

A program error occurred.

Retrieval of the font size bar has failed.

50818 FreeLayout Communicator

Get FontInfo Error.(FontSizeText)

A program error occurred.

Retrieval of the font size text has failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-283

Appx MT1-284
Event Event Source Description
Get FontInfo Error. (FontSizeOverlayInfo)

Causes
A program error occurred.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks
Retrieval of the font size overlay has failed.

50818 FreeLayout Communicator

50818 FreeLayout Communicator

Get SystemInfo Error. (DateFormat)

A program error occurred.

Retrieval of the date format has failed.

50818 FreeLayout Communicator

Get SystemInfo Error. (TimeFormat)

A program error occurred.

Retrieval of the time format has failed.

50818 FreeLayout Communicator

Get SysMDB error. ()

A program error occurred.

Retrieval of a text string or a numerical value from the text DB has failed.

50818 FreeLayout Communicator

Execute FFNetDBGetSystemInfo error.()

A program error occurred.

Retrieval of the system information for the Device ID has failed.

50818 FreeLayout Communicator

Get MeasurUnit Error. (SystemMeasurUnit)

A program error occurred.

Unit retrieval from the system settings has failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-284

Appx MT1-285
Event Event Source Description
FFStrDBReadString Error.()

Causes
A program error occurred.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks
Retrieval of angle measuring unit text string has failed.

50818 FreeLayout Communicator

50818 FreeLayout Communicator

FFStrDBConnect error.()

A program error occurred.

Opening of the text DB has failed.

50818 FreeLayout Communicator

FFGetString error.()

A program error occurred.

Retrieval of the text DB file path has failed.

50818 FreeLayout Communicator

GetUserIDToName Error.

User information retrieval has failed.

50818 FreeLayout Communicator

Get ddo_alloc_string_VR Error.

VR allocation failure error. PN conversion failure error. Information retrieval failure error after PN conversion.

50818 FreeLayout Communicator

CreateXMLObject Error.

XML file read-in conversion has failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-285

Appx MT1-286
Event Event Source Description
RegistExclusion Error.

Causes
Exclusion right retrieval has failed.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

50818 FreeLayout Communicator

50818 FreeLayout Communicator

ResetExclusion Error.

Exclusion right has been released.

50819 FreeLayout Communicator

DownloadFile error.

A program error occurred.

File download from the server has failed.

50819 FreeLayout Communicator

GetPathInfo error.(USER_TEMP_ A program error occurred. PATH)

Work folder retrieval from Directory.ini has failed.

50819 FreeLayout Communicator

CABFilePack error.

A program error occurred.

CAB packing has failed.

50819 FreeLayout Communicator

UploadToOutput error.

A program error occurred.

Uploading has failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-286

Appx MT1-287
Event Event Source Description
DDO Not Initialize Exception. Exceptional error.

Causes
A program error occurred.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks
Initialization has failed.

50819 FreeLayout Communicator

50819 FreeLayout Communicator

DDO Tag Not Exist Exception. Exceptional error.

A program error occurred.

Missing tag error.

50819 FreeLayout Communicator

DDO TagLengh Zero Exception. Exceptional error.

A program error occurred.

Length error.

50819 FreeLayout Communicator

Exceptional error (message output A program error occurred. by OS).

50819 FreeLayout Communicator

DDO Load Exception. Exceptional error.

A program error occurred.

Load failure error.

50819 FreeLayout Communicator

DDO Not Initialize. Exceptional error.

A program error occurred.

DICOM handle not set error.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-287

Appx MT1-288
Event Event Source Description
DDO Save Exception. Exceptional error.

Causes
A program error occurred.

Remedies
Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks
Saving has failed.

50819 FreeLayout Communicator

50819 FreeLayout Communicator

DOD Tag Not Exist. Exceptional error.

A program error occurred.

A tag does not exist.

50819 FreeLayout Communicator

Exceptional error.

A program error occurred.

An exception has occurred when an error occurred with access to the network by pluggable protocol.

50855 FFCustomMsgBox

[50855] Format name cannot be Prohibited characters have been used for a Reconfirm the format name and try again. empty or contain special character format name. (\ / : * ? < > |). *Please confirm the format name again.

50856 FFCustomMsgBox

[50856] There exists format with the same name. *Please input the new one. [50858] The maximum number of formats creatable has been reached. *To create new format, please delete older format(s).

The entered format name already exists.

Change the name and try again.

50858 FFCustomMsgBox

The upper limit for the number of formats which can be created has been exceeded.

Delete registered formats and try again.

50861 FFCustomMsgBox

[50861] Unable to set up printer. Free Layout cannot be started. >Contact your service engineer.

No printer has been set.

Use the service utility to confirm the printer settings and try again.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-288

Appx MT1-289
Event Event Source Description
[50862] Failed in Free Layout output. *Restart the computer. >Contact your service engineer if restarting of the computer does not resolve the problem. 50863 FFCustomMsgBox [50863] Failed in Free Layout output. *Restart the computer. >Contact your service engineer if restarting of the computer does not resolve the problem. 50864 FFCustomMsgBox [50864] There is not enough memory. *Restart the computer. >Contact your service engineer if restarting of the computer does not resolve the problem. 50867 FFCustomMsgBox 50872 FFCustomMsgBox

Causes

Remedies

Remarks

50862 FFCustomMsgBox

The output target folder may not have been Restart both the server application and specified. client application. If the same error recurs, restart the computer. If restarting of the computer does not resolve the problem, confirm the situation in which the error occurred, and submit the event log to the manufacturer. File output to the output target folder may not be possible. Restart both the server application and client application. If the same error recurs, restart the computer. If restarting of the computer does not resolve the problem, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

It is possible that there is not sufficient free Restart the computer and then retry the memory for reading in images at the free operation. layout screen. If restarting of the computer does not resolve the problem, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Perform image layout and try again. Change the resolution of the PC and try again.

[50867] No image layout has been Printing has been executed without performed. execution of image layout. Printing cannot be executed. [50872] Insufficient monitor resolution. Free Layout screen cannot be displayed. >Contact your service engineer. [50873] An error has occurred. Free Layout will be terminated. *Restart the computer. >Contact your service engineer if restarting of the computer does not resolve the problem. The monitor resolution is not sufficient.

50873 FFCustomMsgBox

An error with unknown cause has occurred. Restart both the server application and client application. If the same error recurs, restart the computer. If restarting of the computer does not resolve the problem, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart both the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

50875 FreeLayout Communicator

An error has occurred at the free layout ErrorCode:%1%n screen. SubSystem:%2%n SourceFile: %3%n SpotCode: %4%n The error at the time of start of the freelayout screen.\n

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-289

Appx MT1-290
Event Event Source Description
Initialize Warning.%n[%1]

Causes

Remedies

Remarks
Output section container.

51001 FFOUTPUT

Initialization process warning. Check the network settings again. If the The output equipment execution was not settings are correct, perform a successfully started. reinstallation. The output equipment name (AE name/ host name) was not successfully acquired (there was an inconsistency between the option and network settings). The FFNET database was not successfully accessed. Initialization process warning. Check the network settings again. If the The output equipment execution was not settings are correct, perform a successfully started. reinstallation. The output equipment name (AE name/ host name) was not successfully acquired (there was an inconsistency between the option and network settings). The FFNET database was not successfully accessed. State change notification process warning. Restart. An acquisition request was not successfully answered. State change notification process warning. Restart. An acquisition request was not successfully answered.

51001 Spooler

Initialize Warning.%n[%1]

Output section container.

51002 FFOUTPUT 51002 Spooler 51003 FFOUTPUT 51003 Spooler 51004 FFOUTPUT 51004 Spooler 51005 FFOUTPUT 51005 Spooler 51006 FFOUTPUT 51006 Spooler 51007 FFOUTPUT

State Change Warning.%n[%1] State Change Warning.%n[%1] Routine Change Warning.%n[%1] Routine Change Warning.%n[%1] Spool Warning.%n[%1] Spool Warning.%n[%1] ExeOutput Warning.%n[%1] ExeOutput Warning.%n[%1] Image Proc Warning.%n[%1] Utility Request Warning.%n[%1] Output Proc Warning.%n[%1]

Output section container. Output section container. Output section container. Output section container.

Spool process warning. Spool process warning. Forced-output process warning Forced-output process warning An image process warning. A utility transition process warning. Output processing warning

Output section container. Output section container. Output section container. Output section container. Output section container. Output section container. Output section container.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-290

Appx MT1-291
Event Event Source Description
Terminate Warning.%n[%1]

Causes
Restart. Termination process warning. A process status flag was not successfully set. A process termination response message was not successfully transmitted. An abnormality occurrence notification message was not successfully transmitted. A message box was not successfully displayed. A spooler termination request was not successfully called. A spooler control end request was not successfully called. The spooler control end response state was abnormal. An image process control end request was not successfully issued. An output device control end request was not successfully issued. The output device control end response state was abnormal. Commitment process warning. An image process warning. Queue resumption process warning. Output processing warning The setup data was incorrect or the equipment not started. Queue deletion process warning. Queue resumption process warning. The setup file format was incorrect or the file could not be read. Equipment output suspension process warning. Queue deletion process warning. The setup file format was incorrect or the file could not be read. Equipment output resumption warning. Equipment output suspension process warning. The system was unstable. Queue priority change warning.

Remedies

Remarks
Output section container.

51007 Spooler

51008 FFOUTPUT 51008 Spooler 51009 FFOUTPUT 51009 Spooler 51010 FFCustomMsgBox 51010 FFOUTPUT 51010 Spooler 51011 51011 51011 FFCustomMsgBox FFOUTPUT Spooler

Commit Proc Warning.%n[%1] Image Proc Warning.%n[%1] Queue Resume Warning.%n[%1] Output Proc Warning.%n[%1] Specified device does not exist. Queue Delete Warning.%n[%1] Queue Resume Warning.%n[%1] Failed in reading of the configuration file (TagLookup.ini). Unit Suspend Warning.%n[%1] Queue Delete Warning.%n[%1] Failed in reading of the gray level correction file. Unit Resume Warning.%n[%1] Unit Suspend Warning.%n[%1] Failed in output process. Priority Change Warning.%n[%1]

Output section container. Output section container. Output section container. Output section container. Check settings or the equipment. Output section container. Output section container. Check settings. Output section container. Output section container. Check settings. Output section container. Output section container. Restart. If the same symptom recurs, perform a reinstallation. Output section container.

51012 FFCustomMsgBox 51012 FFOUTPUT 51012 Spooler 51013 FFCustomMsgBox 51013 FFOUTPUT
020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-291

Appx MT1-292
Event Event Source Description
Unit Resume Warning.%n[%1] Utility Request Warning.%n[%1] Terminate Warning.%n[%1]

Causes
Equipment output resumption warning. A utility transition process warning. Termination process warning. Restart. A process status flag was not successfully set. A process termination response message was not successfully transmitted. An abnormality occurrence notification message was not successfully transmitted. A message box was not successfully displayed. A spooler termination request was not successfully called. A spooler control end request was not successfully called. The spooler control end response state was abnormal. An image process control end request was not successfully issued. An output device control end request was not successfully issued. The output device control end response state was abnormal.

Remedies

Remarks
Output section container. Output section container. Output section container.

51013 Spooler 51014 FFOUTPUT 51015 FFOUTPUT

51025 FFCustomMsgBox 51050 FFCustomMsgBox 51051 FFCustomMsgBox 51100 FFOutPutEvent

An image being output exists. An attempt to output images to the printer resulted in a failure. An attempt to output images to the printer resulted in a failure. ErrorCode:%1%nSubSystem:%2 An exception occurred when a method for %nSourceFile: %3%nSpotCode: Run Proc execution was used. An internal %4%nThe method exception error system error occurred. at the time of Run Proc execution.\n

Press OK to shut down the system. Otherwise, press Cancel.

Restart. If the same symptom recurs, perform a reinstallation.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51101

FFOutPutEvent

ErrorCode:%1%nSubSystem:%2 An exception occurred when a method for %nSourceFile: %3%nSpotCode: End Proc execution was used. An internal %4%nThe method exception error system error occurred. at the time of End Proc execution.\ n

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-292

Appx MT1-293
Event
51102

Event Source
FFOutPutEvent

Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile:%3%nSpotCode:% 4%nNotice method exception error of a Queue operation end.\n

Causes
An exception occurred when the queue operation termination notification method was used. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51103

FFOutPutEvent

ErrorCode:%1%nSubSystem:%2 An exception occurred during main thread %nSourceFile: %3%nSpotCode: execution. An internal system error %4%nThe exception error at the occurred. time of an end during main thread execution.\n

Restart. If the same symptom recurs, perform a reinstallation.

51104

FFOutPutEvent

ErrorCode:%1%nSubSystem:%2 The output operation table was not %nSourceFile:%3%nSpotCode:% successfully initialized. An internal system 4%nThe initialization error of an error occurred. output operation table.\n

Restart. If the same symptom recurs, perform a reinstallation.

51105

FFOutPutEvent

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of state changes of an output operation table.\n

Output operation table state transition failed. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51106

FFOutPutEvent

ErrorCode:%1%nSubSystem:%2 An exception occurred during an %nSourceFile:%3%nSpotCode:% XMLCreation process. An internal system 4%nXMLCreation processing error occurred. exception error.\n

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-293

Appx MT1-294
Event
51107

Event Source
FFOutPutEvent

Description

Causes

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

ErrorCode:%1%nSubSystem:%2 An exception occurred during SQL %nSourceFile:%3%nSpotCode:% execution. An internal system error 4%nExecQuery error.\n occurred.

51108

FFOutPutEvent

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nSQL execution result acquisition error.\n

The SQL execution result was not successfully acquired. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51109

FFOutPutEvent

ErrorCode:%1%nSubSystem:%2 An exception occurred during an output Restart. If the same symptom recurs, %nSourceFile:%3%nSpotCode:% operation read process. An internal system perform a reinstallation. 4%nOutput operation reading error occurred. processing exception error.\n

51110

FFOutPutEvent

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nOutput operation information deletion error.\n

The output operation information was not successfully deleted. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51149

FFOutPutEvent

ErrorCode:%1%nSubSystem:%2 An error of unknown cause occurred. %nSourceFile:%3%nSpotCode:% 4%nUnknown Error.\n

Restart both the server PC and client PC. If the same error recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-294

Appx MT1-295
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of constructor generation.\n

Causes
The constructor was not successfully generated. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51200 FFMediaOutput

51201 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of the message transmission to a main thread.\n

An exception occurred during main thread execution. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51202 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred during main thread %nSourceFile: %3%nSpotCode: execution. An internal system error %4%nThe error at the time of the occurred. message transmission2 to a main thread.\n

Restart. If the same symptom recurs, perform a reinstallation.

51203 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of the message transmission to a main thread.\n

Message transmission to the output thread Restart. If the same symptom recurs, failed. An internal system error occurred. perform a reinstallation.

51204 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 A message transmission to the reserve %nSourceFile:%3%nSpotCode:% queue failed. An internal system error 4%nThe message transmitting occurred. error to reserve queue.\n

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-295

Appx MT1-296
Event Event Source Description Causes Remedies Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). 51205 FFMediaOutput ErrorCode:%1%nSubSystem:%2 Message transmission to the status Restart. If the same symptom recurs, %nSourceFile:%3%nSpotCode:% monitoring thread failed. An internal system perform a reinstallation. 4%nThe message transmitting error occurred. error to a state surveillance thread.\n

51206 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred when a method for %nSourceFile: %3%nSpotCode: Run Proc execution was used. An internal %4%nThe method exception error system error occurred. at the time of Run Proc execution.\n

Restart. If the same symptom recurs, perform a reinstallation.

51207 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred when a method for %nSourceFile: %3%nSpotCode: End Proc execution was used. An internal %4%nThe method exception error system error occurred. at the time of End Proc execution.\ n

Restart. If the same symptom recurs, perform a reinstallation.

51208 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred when a method for %nSourceFile: %3%nSpotCode: MediaOutputPrc execution was used. %4%nThe method exception error An internal system error occurred. at the time of Media Output Proc execution.\n

Restart. If the same symptom recurs, perform a reinstallation.

51209 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred during main thread %nSourceFile: %3%nSpotCode: execution. An internal system error %4%nThe exception error at the occurred. time of an end during main thread execution.\n

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-296

Appx MT1-297
Event Event Source Description Causes Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51210 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred during output %nSourceFile:%3%nSpotCode:% request thread execution. This is an 4%nThe exception error at the internal system error. time of an end during output thread execution.\n

51211

FFMediaOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred while the status %nSourceFile: %3%nSpotCode: monitoring thread was being executed. %4%nThe exception error at the This is an internal system error. time of an end during surveillance thread execution.\n

Restart. If the same symptom recurs, perform a reinstallation.

51212 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 An XML character string was not %nSourceFile:%3%nSpotCode:% successfully read. An internal system error 4%nXML character sequence load occurred. error.\n

Restart. If the same symptom recurs, perform a reinstallation.

51213 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nXML character reading error.\n

With the Client Utility, review the setup Restart. If the same symptom recurs, information about the automatic verification perform a reinstallation. user.

51214 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nHistory information file generation error.\n

The history information file was not successfully created. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-297

Appx MT1-298
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nPicture storage demand data creation error.\n

Causes
Image storage request data was not successfully created. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51215 FFMediaOutput

51216 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nXML character reading processing exception error.\n

An exception occurred during an XML Restart. If the same symptom recurs, character read process. An internal system perform a reinstallation. error occurred.

51217 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 A media control instruction component %nSourceFile:%3%nSpotCode:% deletion request was not successfully 4%nMedia control directions issued. An internal system error occurred. component deletion demand failure.\n

Restart. If the same symptom recurs, perform a reinstallation.

51249 FFMediaOutput

ErrorCode:%1%nSubSystem:%2 An error of unknown cause occurred. %nSourceFile:%3%nSpotCode:% 4%nUnknown Error.\n

Restart both the server PC and client PC. If the same error recurs, perform a reinstallation.

51250 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of constructor generation.\n

The constructor was not successfully generated. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-298

Appx MT1-299
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of the message transmission to a main thread.\n

Causes
An exception occurred during main thread execution. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51251 FFGeneralOutput

51252 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of the message transmission to a main thread.\n

Message transmission to the output thread Restart. If the same symptom recurs, failed. An internal system error occurred. perform a reinstallation.

51253 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 A message transmission to the reserve %nSourceFile:%3%nSpotCode:% queue failed. An internal system error 4%nThe message transmitting occurred. error to reserve queue.\n

Restart. If the same symptom recurs, perform a reinstallation.

51254 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred when a method for %nSourceFile: %3%nSpotCode: Run Proc execution was used. An internal %4%nThe method exception error system error occurred. at the time of Run Proc execution.\n

Restart. If the same symptom recurs, perform a reinstallation.

51255 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred when a method for %nSourceFile: %3%nSpotCode: End Proc execution was used. An internal %4%nThe method exception error system error occurred. at the time of End Proc execution.\ n

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-299

Appx MT1-300
Event Event Source Description Causes Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51256 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred during main thread %nSourceFile: %3%nSpotCode: execution. An internal system error %4%nThe exception error at the occurred. time of an end during main thread execution.\n

51257 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred during output %nSourceFile:%3%nSpotCode:% request thread execution. This is an 4%nThe exception error at the internal system error. time of an end during output thread execution.\n

Restart. If the same symptom recurs, perform a reinstallation.

51258 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nXML character reading error.\n

With the Client Utility, review the setup Restart. If the same symptom recurs, information about the automatic verification perform a reinstallation. user.

51259 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDDO file name reading error.\n

A DDO filename was not successfully read. Restart. If the same symptom recurs, An internal system error occurred. perform a reinstallation.

51260 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nXML character reading processing exception error.\n

An exception occurred during an XML Restart. If the same symptom recurs, character read process. An internal system perform a reinstallation. error occurred.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-300

Appx MT1-301
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt error-generates within a processed picture generation component.\n

Causes
Image processing failed. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51261 FFGeneralOutput

51262 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nPicture number-of-sheets reading error.\n

The number of images was not successfully read. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51263 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 A bitmap generation process was not Restart. If the same symptom recurs, %nSourceFile: %3%nSpotCode: successfully performed. An internal system perform a reinstallation. %4%nIt error-generates in bit map error occurred. generation processing.\n

51264 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe exception error at the time of bit map creation.\n

An exception occurred when an attempt was made to create a bitmap. This is an internal system error.

Restart. If the same symptom recurs, perform a reinstallation.

51265 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nRAW data reading error.\n

The RAW data was not successfully read. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-301

Appx MT1-302
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe exception error at the time of Jpeg file creation.\n

Causes
An exception occurred when an attempt was made to create a JPEG file. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51266 FFGeneralOutput

51267 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nHistory file creation went wrong.\n

The history file was not successfully Restart. If the same symptom recurs, created. An internal system error occurred. perform a reinstallation.

51268 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nHistory file creation processing exception error.\n

An exception occurred during a history file Restart. If the same symptom recurs, creation process. This is an internal system perform a reinstallation. error.

51269 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nFile path specification of a copy place is unusual.\n

The general-purpose file was not successfully output. The copy destination file path was not properly specified.

With the User Utility, check the copy destination setting. If the same error recurs, perform a reinstallation.

51270 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe holder of a copy place is not found.\n

The general-purpose file was not successfully output. The copy destination file path was not properly specified.

With the User Utility, check the copy destination setting. If the same error recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-302

Appx MT1-303
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCopy advance withdrawal power processing exception error (a network cuts during a file copy).\n

Causes
An exception occurred during the copy destination output process. The network was disconnected while a file was copied.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51271 FFGeneralOutput

51272 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nUnknown Error.\n

An error of unknown cause occurred.

Restart both the server PC and client PC. If the same error recurs, perform a reinstallation.

51284 FFGeneralOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAn initialization error of a component (FFMultiImgProcCOM).\n

Component initialization failed.

Restart. If the same symptom recurs, perform a reinstallation.

51285 GeneralOutput

I failed in the setting of the input image format.

A program error occurred.

Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

51286 GeneralOutput

DDO file name reading error.

A program error occurred.

51287 GeneralOutput

Width of the output image size or height is 0.

A program error occurred.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-303

Appx MT1-304
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of constructor generation.\n

Causes
The constructor was not successfully generated. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51300 FFCaRnaOutput

51301 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of the message transmission to a main thread.\n

An exception occurred during main thread execution. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51302 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of the message transmission to a main thread.\n

Message transmission to the output thread Restart. If the same symptom recurs, failed. An internal system error occurred. perform a reinstallation.

51303 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe message transmitting error to reserve queue.\n

A message transmission to the reserve queue failed. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51304 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe message transmitting error to a state surveillance thread.\n

Message transmission to the status Restart. If the same symptom recurs, monitoring thread failed. An internal system perform a reinstallation. error occurred.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-304

Appx MT1-305
Event Event Source Description Causes Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51305 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred when a method for %nSourceFile: %3%nSpotCode: Run Proc execution was used. An internal %4%nThe method exception error system error occurred. at the time of Run Proc execution.\n

51306 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred when a method for %nSourceFile: %3%nSpotCode: End Proc execution was used. An internal %4%nThe method exception error system error occurred. at the time of End Proc execution.\ n

Restart. If the same symptom recurs, perform a reinstallation.

51307 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred when a method for %nSourceFile: %3%nSpotCode: CaRnaOutputPrc execution was used. %4%nThe method exception error An internal system error occurred. at the time of C@Rna Output Proc execution.\n

Restart. If the same symptom recurs, perform a reinstallation.

51308 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred during main thread %nSourceFile: %3%nSpotCode: execution. An internal system error %4%nThe exception error at the occurred. time of an end during main thread execution.\n

Restart. If the same symptom recurs, perform a reinstallation.

51309 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe exception error at the time of an end during output thread execution.\n

An exception occurred during output request thread execution. This is an internal system error.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-305

Appx MT1-306
Event Event Source Description Causes Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51310 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 An exception occurred while the status %nSourceFile: %3%nSpotCode: monitoring thread was being executed. %4%nThe exception error at the This is an internal system error. time of an end during surveillance thread execution.\n

51311

FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nXML character reading error.\n

With the Client Utility, review the setup Restart. If the same symptom recurs, information about the automatic verification perform a reinstallation. user.

51312 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nPicture number-of-sheets reading error.\n

The number of images was not successfully read. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51313 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe reading error of delivery classification.\n

The delivery type was not successfully read. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51314 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nAbstract syntax reading error.\n

The abstract syntax was not successfully read. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-306

Appx MT1-307
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nTransmission syntax reading error.\n

Causes
The transmission syntax was not successfully read. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51315 FFCaRnaOutput

51316 FFCaRnaOutput

ErrorCode:%1%nSubSystem: An attempt to read the C@Rna image %2%nSourceFile: transfer parameter character string failed. %3%nSpotCode: %4%nC@Rna An internal system error occurred. picture transmission parameter character sequence reading error.\ n

Restart. If the same symptom recurs, perform a reinstallation.

51317 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDDO file name reading error.\n

A DDO filename was not successfully read. Restart. If the same symptom recurs, An internal system error occurred. perform a reinstallation.

51318 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nXML character reading processing exception error.\n

An exception occurred when an attempt was made to read XML characters. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51319 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 The DICOM stream file was not %nSourceFile: %3%nSpotCode: successfully created. An internal system %4%nDICOM stream file creation error occurred. error.\n

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-307

Appx MT1-308
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDDO file Open error.\n

Causes
A DDO file was not successfully read. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51320 FFCaRnaOutput

51321 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 The property settings are inconsistent. %nSourceFile: %3%nSpotCode: An internal system error occurred. %4%nThey are those with inconsistency to a property setup.\ n

Restart. If the same symptom recurs, perform a reinstallation.

51322 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nIt error-generates within a processed picture generation component.\n

Image processing failed. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51323 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 A bitmap generation process was not Restart. If the same symptom recurs, %nSourceFile: %3%nSpotCode: successfully performed. An internal system perform a reinstallation. %4%nIt error-generates in bit map error occurred. generation processing.\n

51324 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nPicture storage request processing exception error.\n

An exception occurred while an image Restart. If the same symptom recurs, storage request process was being perform a reinstallation. performed. This is an internal system error.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-308

Appx MT1-309
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of picture storage execution.\n

Causes
Image storage failed. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51325 FFCaRnaOutput

51326 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of case picture registration file registration.\n

An attempt to register a case study image registration file failed. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51327 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nCase picture registration processing exception error.\n

An exception occurred during a case study Restart. If the same symptom recurs, image registration process. This is an perform a reinstallation. internal system error.

51328 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nDICOM stream picture generation processing exception error.\n

An exception occurred when a DICOM stream image generation process was performed.

Restart. If the same symptom recurs, perform a reinstallation.

51329 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of a Teleradiology request upload demand.\n

An attempt to make a request for a remote Restart. If the same symptom recurs, radiological interpretation request upload perform a reinstallation. failed. An internal system error occurred.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-309

Appx MT1-310
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nTeleradiology request upload demand exception error. \n

Causes
An exception occurred when an attempt was made to make a request for a remote radiological interpretation request upload. This is an internal system error.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51330 FFCaRnaOutput

51331 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nA delivery result is notified to an output main process. It error-notifies.\n

The delivery result notification was not Restart. If the same symptom recurs, successfully sent to the output main perform a reinstallation. process. An internal system error occurred.

51332 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 PN conversion/unicode data acquisition %nSourceFile: %3%nSpotCode: from a DICOMObject failed. An internal %4%nPN conversion, the Unicode system error occurred. data acquisition error from DICOM Object.\n

Restart. If the same symptom recurs, perform a reinstallation.

51333 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nPN conversion, an internal expression change error.\n

PN conversion/internal expression change failed. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51334 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 An attempt to acquire the upload support %nSourceFile: %3%nSpotCode: component status failed. An internal %4%nUpload support component system error occurred. state acquisition error.\n

Restart. If the same symptom recurs, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-310

Appx MT1-311
Event Event Source Description
ErrorCode:%1%nSubSystem: %2%nSourceFile: %3%nSpotCode: %4%nUpload support component processing discontinuation.\n

Causes
The upload support component process was aborted. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51337 FFCaRnaOutput

51338 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 An attempt to output an image to the C@ %nSourceFile: %3%nSpotCode: Rna data center failed. An internal system %4%nThe application error by the error occurred. side of the upload support component at the time of state acquisition.\n

Restart. If the same symptom recurs, perform a reinstallation.

51339 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe upload support component communication error at the time of state acquisition.\n

An attempt to output an image to the C@ Rna data center failed. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51340 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nPicture output timeout.\n

A timeout occurred when an attempt was made to output an image. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51341 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nA upload support component side Queue-deletiondemand-goes wrong.\n

A queue deletion request failed on the Restart. If the same symptom recurs, upload support component side. An internal perform a reinstallation. system error occurred.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-311

Appx MT1-312
Event Event Source Description
ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nThe error at the time of upload support component starting.\n

Causes
An attempt to start the upload support component failed. An internal system error occurred.

Remedies
Restart. If the same symptom recurs, perform a reinstallation.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program).

51342 FFCaRnaOutput

51343 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nRAW data reading error.\n

The RAW data was not successfully read. An internal system error occurred.

Restart. If the same symptom recurs, perform a reinstallation.

51399 FFCaRnaOutput

ErrorCode:%1%nSubSystem:%2 %nSourceFile: %3%nSpotCode: %4%nUnknown Error.\n

An error of unknown cause occurred.

Restart both the server PC and client PC. If the same error recurs, perform a reinstallation.

51601 FFCustomMsgBox 51602 FFCustomMsgBox 51603 FFCustomMsgBox

The disk inserted in drive for management is inconsistent. Failed in mounting the disk inserted in drive for management. Failed in writing disk management information. Possible causes are: (1)  The drive has not been connected or power of drive is off. (2)  No disk inserted or another disk inserted. [51801] Free Layout cannot be The free layout screen has been started performed since images are being during image display. displayed. *Please wait and retry. [51804] Output in progress *Please wait and retry.

Launch the Client Utlity and execute Disk Restoration. Launch the Client Utility and change disks. Ensure that the drive has been connected correctly and a disk has been inserted into the drive.

51801 FFCustomMsgBox

Retry the operation. If the problem is not resolved, restart the client application.

51804 FFCustomMsgBox

Film output has been performed during film Retry the operation after completion of film output. output.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-312

Appx MT1-313
Event Event Source Description
[51805] Printer has not been set up. >Contact your service engineer. 51807 FFCustomMsgBox [51807] Certain study is being viewed by either one of the units. +Do you wish to continue processing except for the study being viewed? 51808 FFCustomMsgBox [51808] Certain study is being viewed by either one of the units. *Please wait and retry. 51809 FFCustomMsgBox [51809] Free disk space is insufficient. *If the free layout screen is being displayed, close the screen first and then try again. *Delete unnecessary files to increase free disk space. >If not possible to do so, contact your service engineer. 51865 FFCustomMsgBox [51865] Application cannot display There may be no database being used by free layout or access may not be possible. notes or perform note setting. *Restart the computer. >Contact your service engineer if restarting of the computer does not resolve the problem. 51866 FFCustomMsgBox [51866] Failed in storing image incidental information setting. *Restart the computer. >Contact your service engineer if restarting of the computer does not resolve the problem. 51868 FFCustomMsgBox [51868] Study images are being imported. Layout cannot be changed during image import. Layout change for the image being read in has been performed during reading of a study image. There may be no database being used by free layout or access may not be possible. The same study is being referenced from a Retry the operation. different client PC. If the problem is not resolved, restart the client application. Free disk space is insufficient. Delete unnecessary files to increase free disk space, and then try again. If the problem is not resolved, restart the server application and client application. Nothing particular.

Causes
No printer has been set.

Remedies
Use the service utility to confirm the printer settings and try again.

Remarks

51805 FFCustomMsgBox

Restart the PC and then retry the operation. If the problem is not resolved, perform a reinstallation.

Restart the PC and then retry the operation. If the problem is not resolved, perform a reinstallation.

Retry the operation after image reading completion. If the problem is not resolved, restart the client application. Retry the operation after image reading completion. If the problem is not resolved, restart the client application.

51869 FFCustomMsgBox

[51869] Images subject to layout At the time of reading an image, an are being imported. operation has been performed to the image No operation can be performed on being read in. images being imported.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-313

Appx MT1-314
Event Event Source Description
[51870] Cannot read image data. *Restart the computer. >Contact your service engineer if restarting of the computer does not resolve the problem. 52000 FFOutImgPrc 52100 Spooler Warning.%n%1 Spooler Warning.%n%1

Causes
There may be no database being used by free layout or access may not be possible.

Remedies
Restart the PC and then retry the operation. If the problem is not resolved, perform a reinstallation. There is no operational problem. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Spooler

Remarks

51870 FFCustomMsgBox

Information for developers. Common warning message. Queue information class related message. Image information (SOPInstanceUID) was not successfully acquired. The job status was not successfully acquired. Spooler class related message. A database connection was not successfully closed. Illegal image display format data. Initialization process warning. A character string database connection was not successfully opened. Output destination registration process warning

52101 Spooler 52102 Spooler 52103 Spooler

RunProc Warning.%n%1 OutputRegisterProc Warning.%n%1

Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

Spooler Spooler

StateChangeProc Warning.%n%1 Local printer/Dicom printer state change notification process warning. A unit state character string was not successfully acquired. ErrorCheckProc Warning.%n%1 RestoreJob Warning.%n%1 SpoolProc Warning.%n%1 Data integrity check process warning. Job restoration warning. An output job file was not successfully accessed. Spool process warning. Unit information acquisition was not successful. File deletion was not successful. Queue cancellation was not successful. Data was not successfully written into a log file. Reoutput start process warning

Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

Spooler

52104 Spooler 52105 Spooler 52106 Spooler

Spooler Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Spooler Spooler

52107 Spooler 52108 Spooler

ReoutputProc Warning.%n%1 StudyReqEndProc Warning.%n%1

Spooler Spooler

Examination end request process warning. Restart. If the same symptom frequently occurs, perform a reinstallation and then A database was not successfully accessed. initialize the image database. DDO file information was not successfully acquired.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-314

Appx MT1-315
Event Event Source Description
ExeOutputJob Warning.%n%1

Causes

Remedies
Spooler Spooler

Remarks

52109 Spooler 52110 Spooler

Forced output request process warning. Restart. If the same symptom frequently DDO file information was not successfully occurs, perform a reinstallation and then acquired. initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

GetImageProcJob Warning.%n%1 Image processing job acquisition process warning. An output unit type parameter error occurred. SetImageProcComplete Warning.%n%1 GetOutputProcJob Warning.%n%1 SetOutputProcComplete Warning.%n%1 GetCommitProcJob Warning.%n%1 QueueSuspend Warning.%n%1 SetCommitProcComplete Warning.%n%1 QueueResume Warning.%n%1 QueueSuspend Warning.%n%1 QueueDelete Warning.%n%1 Image processing completion notification process warning Output job acquisition response process warning. An output unit type parameter error was encountered. Output completion notification process warning

52111 52112

Spooler Spooler

Spooler Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Spooler

52113 52114

Spooler Spooler

Spooler Spooler

Commitment job acquisition response Restart. If the same symptom frequently process warning. occurs, perform a reinstallation and then A commitment equipment type parameter initialize the image database. error occurred. Queue output pause request process warning. Commitment completion notification process warning. Queue output resumption request process warning. Queue output pause request process warning. Queue deletion request process warning. An image database flag was not successfully set. The DDO file was not successfully deleted. Queue output resumption request process warning. Unit suspension request process warning. A unit status character string was not successfully acquired. Queue deletion request process warning. An image database flag was not successfully set. The DDO file was not successfully deleted. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

52114 52115 52115 52116 52116

Spooler Spooler Spooler Spooler Spooler

Spooler Spooler Spooler Spooler Spooler

52117 52117 52118

Spooler Spooler Spooler

QueueResume Warning.%n%1 UnitSuspend Warning.%n%1 QueueDelete Warning.%n%1

Spooler Spooler Spooler

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-315

Appx MT1-316
Event
52118 52119 52119

Event Source
Spooler Spooler Spooler

Description
UnitResume Warning.%n%1 UnitSuspend Warning.%n%1 SuspendProc Warning.%n%1 UnitResume Warning.%n%1 ResumeProc Warning.%n%1 SuspendProc Warning.%n%1 EndProc Warning.%n%1 ResumeProc Warning.%n%1 EndProc Warning.%n%1

Causes
Unit resumption request process warning. A unit status acquisition error occurred. Unit suspension request process warning. A unit status character string was not successfully acquired. Unit suspension request process warning Unit resumption request process warning. A unit status acquisition error occurred. Unit suspension request process warning Unit suspension request process warning End request process warning Unit suspension request process warning End request process warning

Remedies
Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database. Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler

Remarks

52120 Spooler 52120 Spooler 52121 Spooler 52121 Spooler 52122 Spooler 52123 Spooler 52207 FFCustomMsgBox

Just as the message states. [52207] Failed in output processing of JPEG/BMP file. > Check the network settings with the output device. [52208] Failed in output processing of JPEG/BMP file. > Check the network settings of the output destination. Just as the message states.

52208 FFCustomMsgBox

52209 FFCustomMsgBox

Just as the message states. [52209] Failed in writing JPEG/ BMP file to the output destination. > Check the free space of the recording media. [52210] Failed in output Just as the message states. processing of JPEG/BMP file. > No writable operation is allowed in the output destination folder. [52214] Failed in output processing of JPEG/BMP file. > It may be write-protected. User Cancel Media Not Insert Media Not Blank Media Not Support Disk Capacity Over Just as the message states. PDI output processing was halted. No disk is inserted. This disk is unwritable. Data already written on this disk. This disk is unwritable. An unsupported disk was inserted. This disk in unwritable. Free disk space is insufficient. This disk is unwritable. No particular action is required. Insert a disk and retry processing. Insert a blank disk and retry processing. Insert a supported disk and retry processing. Decrease studies to be output and retry processing.

52210 FFCustomMsgBox

52214 FFCustomMsgBox 52700 PDIWizard 52701 PDIWizard 52706 PDIWizard 52707 PDIWizard 52708 PDIWizard
020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-316

Appx MT1-317
Event Event Source Description
Infomation.%n%1 Initialize Infomation.%n[%1] Initialize Infomation.%n[%1]

Causes
Information for developers. Initialization process information Initialization process information

Remedies
There is no operational problem.

Remarks
Output section container. Output section container. Output section container. Output section container. Output section container. Output section container. Output section container. Output section container. Output section container. Output section container. Output section container. Output section container. Output section container. Output section container. Output section container.

53000 FFOutImgPrc 53001 FFOUTPUT 53001 Spooler 53002 FFOUTPUT 53002 Spooler 53003 FFOUTPUT 53003 Spooler 53004 FFOUTPUT 53004 Spooler 53005 FFOUTPUT 53005 Spooler 53006 Spooler 53006 FFOUTPUT 53007 Spooler 53007 FFOUTPUT 53008 Spooler 53008 FFOUTPUT 53009 FFOUTPUT 53009 Spooler 53010 FFOUTPUT 53010 Spooler 53011 53011 FFOUTPUT Spooler

State Change Information.%n[%1] State change notification process information State Change Information.%n[%1] State change notification process information Routine Change Information.%n[%1] Routine Change Information.%n[%1] Spool Information.%n[%1] Spool Information.%n[%1] ExeOutput Information.%n[%1] ExeOutput Information.%n[%1] Utility Request Information.%n[%1] Image Proc Information.%n[%1] Terminate Information.%n[%1] Output Proc Information.%n[%1] Image Proc Information.%n[%1] Commit Proc Information.%n[%1] Queue Resume Information.%n[%1] Output Proc Information.%n[%1] Queue Resume Information.%n[%1] Routine change processing information Routine change processing information Spool process information Spool process information Forced-output process information Forced-output process information A utility transition process information. Image process information. Termination process warning Output processing information Image process information. Commitment process information output section container. Queue resumption process information. Output processing information Queue resumption process information.

Output section container. Output section container. Output section container. Output section container. Output section container. Output section container. Output section container. Output section container.

Queue Delete Information.%n[%1] Queue deletion process information.

Unit Suspend Information.%n[%1] Equipment output suspension process information. Queue Delete Information.%n[%1] Queue deletion process information. Unit Resume Information.%n[%1] Equipment output resumption information. Unit Suspend Information.%n[%1] Equipment output suspension process information.

53012 FFOUTPUT 53012 Spooler

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-317

Appx MT1-318
Event Event Source Description
Priority Change Information.%n[%1] Unit Resume Information.%n[%1] Utility Request Information.%n[%1] Terminate Information.%n[%1] Spooler Infomation.%n%1 RunProc Infomation.%n%1 OutputRegisterProc Infomation.%n%1 StateChangeProc Infomation.%n%1 RestoreJob Infomation.%n%1 SpoolProc Infomation.%n%1 ReoutputProc Infomation.%n%1 StudyReqEndProc Infomation.%n%1 ExeOutputJob Infomation.%n%1 GetImageProcJob Infomation.%n%1 SetImageProcComplete Infomation.%n%1 GetOutputProcJob Infomation.%n%1 SetOutputProcComplete Infomation.%n%1 GetCommitProcJob Infomation.%n%1 Information in a spool process. Unit type mismatch notification. Reoutput start process information Examination end request process information Forced output request process information Image processing job acquisition process information Image processing completion notification process information Output job acquisition response process information Output completion notification process information Commitment job acquisition response process information. Restart. If the same symptom frequently occurs, perform a reinstallation and then initialize the image database.

Causes
Queue priority change information. Equipment output resumption information. A utility transition process information. Termination process information A common information message. Initialization process information Output destination registration process information Information about the local printer/DICOM printer status change notification process.

Remedies

Remarks
Output section container. Output section container. Output section container. Output section container. Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler

53013 FFOUTPUT 53013 Spooler 53014 FFOUTPUT 53015 FFOUTPUT 53100 Spooler 53101 Spooler 53102 Spooler 53103 Spooler 53104 Spooler 53105 Spooler 53106 Spooler 53107 Spooler 53108 Spooler 53109 Spooler 53110 53111 53112 53113 53114 53114 53115 53115 Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler

ErrorCheckProc Infomation.%n%1 Data integrity check process information.

QueueSuspend Infomation.%n%1 Queue output pause request process information. SetCommitProcComplete Infomation.%n%1 QueueResume Infomation.%n%1 Commitment completion notification process information. Queue output resumption request process information.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-318

Appx MT1-319
Event
53116 53116 53117 53117 53118 53118 53119 53119

Event Source
Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler

Description
QueueDelete Infomation.%n%1 QueueResume Infomation.%n%1 UnitSuspend Infomation.%n%1 UnitResume Infomation.%n%1 QueueDelete Infomation.%n%1 UnitSuspend Infomation.%n%1 SuspendProc Infomation.%n%1 UnitResume Infomation.%n%1 ResumeProc Infomation.%n%1 SuspendProc Infomation.%n%1 EndProc Infomation.%n%1 ResumeProc Infomation.%n%1 EndProc Infomation.%n%1 Logical Program Error. %n %1 %n %2

Causes
Queue deletion request process information. Queue output resumption request process information. Unit suspension request process information. Unit resumption request process information. Queue deletion request process information. Unit suspension request process information. Unit suspension request process information Unit resumption request process information. Unit suspension request process information Unit suspension request process information End request process information Unit suspension request process information End request process information A program error occurred.

Remedies
Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Spooler Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. With the Service Utility, set the correct format tool path.

Remarks

QueueSuspend Infomation.%n%1 Queue output pause request process information.

53120 Spooler 53120 Spooler 53121 Spooler 53121 Spooler 53122 Spooler 53123 Spooler 53600 FFMediaCommon

53600 FFMediaControl

Logical Program Error. [Process ID]=%1% [Thread ID]=%2% [SpotCode]=%3% [LastError]=%4% %5% CreateProcess error [LastError:%4%] [FormatToolPath:%6%]

The format tool path was not properly set.

%1=Process ID %2=Thread ID %3=Spot code %4=Error code of GetLastError () %5=Drive name %6=Format tool path

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-319

Appx MT1-320
Event Event Source Description
Catch Exception Error. %n %1 %n %2

Causes
An exception error occurred.

Remedies
Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Increase the hard disk drives free space, for instance, by deleting images. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. With the Service Utility, check the disk settings. Carry it out again after a while. Insert a medium into the drive. With the Service Utility, check the disk settings. Insert an unformatted medium. Insert a formatted medium. Change the medium.

Remarks

53601 FFMediaCommon

53602 FFMediaCommon

Out Of Memory Error. %n %1 %n %2

Memory allocation failed.

53603 FFMediaCommon

Free Memory Error. %n %1 %n %2

Memory deallocation failed.

53604 FFMediaCommon 53605 FFMediaCommon

Disk Full Error. %n %1 %n %2

The built-in hard disk does not have a sufficient free space.

Accept Invalid Commnd Error. %n An illegal process request was received. %1 %n %2

53606 FFMediaCommon

Cannot passed Xml Schema Check. %n %1 %n %2 ReadOnly Device. %n %1 %n %2 Media Used. %n %1 %n %2 Media no exist. %n %1 %n %2 Not Removable. %n %1 %n %2 Formated Media. %n %1 %n %2 Media un-formatting. %n %1 %n %2 Media Read Only. %n %1 %n %2

An XML schema check failed.

53607 FFMediaCommon 53608 FFMediaCommon 53609 FFMediaCommon 53610 FFMediaCommon 53611 FFMediaCommon

An instruction for writing into a read-only device was issued. An attempt was made to access the currently used medium. No medium is inserted in the specified drive. The specified drive is not a removable drive. A formatted medium is inserted. An unformatted medium is inserted. A read-only medium is inserted.

53612 FFMediaCommon 53613 FFMediaCommon

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-320

Appx MT1-321
Event Event Source Description
Exchange Media. %n %1 %n %2 Demand processing was canceled. %n %1 %n %2 End Process Request. %n %1 %n %2 Electric power off. %n %1 %n %2 DICOMDIR is inconsistent. %n %1 %n %2 Invalid Image Info. %n %1 %n %2 Format Type Not Execution. %n %1 %n %2 Media Full. %n %1 %n %2 Used Media in Drive. %n %1 %n %2 Retrieve Image None. %n %1 %n %2 New Media in Drive. %n %1 %n %2 Process Communication Error. %n %1 %n %2 Verify False. %n %1 %n %2 Format False. %n %1 %n %2 Get Mediafreespace False. %n %1 %n %2 Drive Not Exist. %n %1 %n %2 Folder Not Exist. %n %1 %n %2 File Not Exist. %n %1 %n %2

Causes
The specified medium was not inserted. The requested process was aborted in compliance with a cancellation request. The process was aborted in compliance with a system shutdown request.

Remedies
Insert a correct medium. There is no particular problem. There is no particular problem.

Remarks

53614 FFMediaCommon 53615 FFMediaCommon 53616 FFMediaCommon 53617 FFMediaCommon 53618 FFMediaCommon 53619 FFMediaCommon 53620 FFMediaCommon 53621 FFMediaCommon 53622 FFMediaCommon 53623 FFMediaCommon 53624 FFMediaCommon 53625 FFMediaCommon 53626 FFMediaCommon 53627 FFMediaCommon 53628 FFMediaCommon 53629 FFMediaCommon 53630 FFMediaCommon 53631 FFMediaCommon

The process was aborted due to power off. There is no particular problem. The DICOMDIR file is inconsistent. The entered image information is illegal. Since the formatting method was invalidated, formatting was not accomplished. The medium is full. The inserted medium is not new. The image to be acquired was not found. A new medium is inserted. An error occurred in the communication control. The medium was not successfully verified. The medium was not successfully formatted. The free space of the medium was not successfully acquired. The specified drive was not found. The specified folder was not found. The specified file was not found. Rebuild the disk with the Client Utility. Check the images stored on the medium. With the Service Utility, check the disk settings. There is no particular problem. Insert a new medium. Rebuild the disk with the Client Utility. Insert a correct medium. Restart the server computer. Check the drive connection. Check that the medium is not writeprotected. Also, check that the medium is supported by the drive. Check that the medium is not writeprotected. Also, check that the medium is supported by the drive. Restart the server computer. Restart the server computer. Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-321

Appx MT1-322
Event Event Source Description
Readonly File. %n %1 %n %2 File Error. %n %1 %n %2 Write Protect. %n %1 %n %2 Lock False. %n %1 %n %2 Unlock False. %n %1 %n %2 Eject False. %n %1 %n %2 Appoint Tag Is Empty. %n %1 %n %2 No Necessity Media. %n %1 %n %2 Not Dicomdir Struct. %n %1 %n %2 Not Found Mediauid. %n %1 %n %2 Not Found Label. %n %1 %n %2 Process Busy. %n %1 %n %2 Media Exchange. %n %1 %n %2 Record Not Exist. %n %1 %n %2 Error Image Exist. %n %1 %n %2 Registration failure to DB. %n %1 %n %2 Set Default by acquisition failure. %n %1 %n %2 The Same Label Exists. %n %1 %n %2 Rebuild Necessity Media. %n %1 %n %2 Not Manage Media. %n %1 %n %2

Causes
The specified file or folder is read-only. An attempt to access a file failed. The medium is write-protected. The medium was not successfully locked. The medium was not successfully unlocked. The medium was not successfully ejected. The specified tag was empty. This medium does not need to be rebuilt.

Remedies
There is no particular problem. There is no particular problem. There is no particular problem. There is no particular problem. There is no particular problem. There is no particular problem. There is no particular problem. There is no particular problem.

Remarks

53632 FFMediaCommon 53633 FFMediaCommon 53634 FFMediaCommon 53635 FFMediaCommon 53636 FFMediaCommon 53637 FFMediaCommon 53638 FFMediaCommon 53639 FFMediaCommon 53640 FFMediaCommon 53641 FFMediaCommon 53642 FFMediaCommon 53643 FFMediaCommon 53644 FFMediaCommon 53645 FFMediaCommon 53646 FFMediaCommon 53647 FFMediaCommon 53648 FFMediaCommon 53649 FFMediaCommon 53650 FFMediaCommon 53651 FFMediaCommon

The specified path does not have a DICOM There is no particular problem. structure. The media UID cannot be acquired. The label name cannot be acquired. Rebuilding is in progress. The medium is changed. The specified record was not found. A certain image was not successfully acquired. Reconstruct the media. With the Service Utility, check the disk drive settings. With the Service Utility, check the disk drive settings. With the Service Utility, check the disk drive settings. With the Service Utility, check the disk drive settings. There is no particular problem.

A record was not successfully registered in There is no particular problem. the database. Since the setting information could not be With the Service Utility, check whether the acquired, the default information was used. network settings are correct. An existing medium has a label having the same name. This medium needs to be rebuilt. The specified medium is not a management medium. Restart the server computer. Restart the server computer. Restart the server computer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-322

Appx MT1-323
Event Event Source Description
[Control]%1 : Other Error. %n [Function] %2%n [Code] %3%n [Exp] %4%n %5 [Control]%1 : Memory not allocated. %n [Function] %2%n [Code] %3%n [Exp] %4%n %5 [Control]%1 : File I/O Error. %n [Function] %2%n [Code] %3%n [Exp] %4%n %5 [Control]%1 : ddo error. %n [Function] %2%n [Code] %3%n [Exp] %4%n %5 [54802] Do you wish to output this layout as is? [54803] Do you close a free layout screen? HobbitIF.CheckImage() failed. file= result= [54850] Changing the layout will result in loss of some images. +Do you want to continue? 54851 FFCustomMsgBox 54852 FFCustomMsgBox [54851] Do you wish to change the film direction? [54852] This cell has already contained an image. +Do you want to replace that image? 54853 FFCustomMsgBox [54853] The selected image will be deleted. +Do you want to continue? Nothing particular. Nothing particular. Nothing particular. Free layout has been selected for an abnormal image (picture failure/deleted image etc.).

Causes
An unknown error occurred.

Remedies
Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Confirm the situation in which the error occurred, obtain the maintenance log with the Backup Utility, and send the maintenance log and an error report to the manufacturer. Nothing particular. Nothing particular. There is no operational problem (select study of a picture failure/deleted image etc. and not free layout). Nothing particular.

Remarks

53652 FFMediaCommon

53653 FFMediaCommon

Memory allocation failed.

53654 FFMediaCommon

An attempt to access a file failed.

53655 FFMediaCommon

The DICOM image information was not successfully accessed.

54802 FFCustomMsgBox 54803 FFCustomMsgBox 54815 FreeLayout Communicator 54850 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-323

Appx MT1-324
Event Event Source Description
[54854] Images being laid out will be all deleted. +Do you want to continue? 54857 FFCustomMsgBox 54859 FFCustomMsgBox 54860 FFCustomMsgBox [54857] The format will be deleted. +Do you want to continue? [54859] Film size will be changed. +Do you want to continue? [54860] The maximum number of The number of displayable characters has been exceeded with footer information displayable characters has been exceeded. Certain area cannot be setting at the free layout print screen. displayed. +Do you want to continue? 54871 FFCustomMsgBox [54871] Images of multiple patients will be laid out. +Do you want to continue? 55847 FreeLayoutLauncher ErrorCode:%1%n Occurrence of an exception error at the time of start of the free layout screen SubSystem:%2%n SourceFile: %3%n SpotCode: %4%n The error at the time of start of the freelayout screen.\n 55848 FreeLayoutLauncher ErrorCode:%1%n Invalid program error at the time of start of SubSystem:%2%n the free layout screen SourceFile: %3%n SpotCode: %4%n The error at the time of start of the freelayout screen.\n 55849 FreeLayoutLauncher ErrorCode:%1%n File access error at the time of start of the SubSystem:%2%n free layout screen SourceFile: %3%n SpotCode: %4%n The error at the time of start of the freelayout screen.\n 57601 OutImgPrc DDO data(0x0007,0xF815) are not data to set in an input image format A program error occurred. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Nothing particular. When the existence of not displayable characters is possible, click [OK], otherwise click [Cancel]. Nothing particular. Nothing particular.

Causes

Remedies
Nothing particular.

Remarks

54854 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-324

Appx MT1-325
Event Event Source Description
Transfer sentence Get Error. < SetInputOutputImageType

Causes
A program error occurred.

Remedies
Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart. If the same symptom recurs, perform a reinstallation.

Remarks

57602 OutImgPrc

57603 OutImgPrc

JOBFile data(0x1000,0x0021) are A program error occurred. not data to set in output image format

57604 OutImgPrc

Catch some other Exception < COutImgPrc:: SetInputOutputImageType

A program error occurred.

57605 OutImgPrc

DDO File Reset Error

A program error occurred.

60000 FFCustomMsgBox 60002 FFCustomMsgBox 60003 FFCustomMsgBox 60004 FFCustomMsgBox 60005 FFCustomMsgBox 60006 FFCustomMsgBox 60007 FFCustomMsgBox 60008 FFCustomMsgBox

Failed in accessing the database. User Utility will be terminated. The system cannot be started because the server application has already been up and running. The system cannot be started because the Service Utility has already been up and running. The system cannot be started because the Service Utility has already been up and running. The system cannot be started because the Service Utility has already been up and running. An error occurred during user authentication processing. An error occurred during user authentication processing.

It is conceivable that the database file was damaged or deleted.

An abnormality is encountered. There is no Restart. If the same symptom recurs, alternative but to exit the program. perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-325

Appx MT1-326
Event Event Source Description
Failed in accessing the character string database. Failed in accessing the system setting database. Failed in obtaining the registry information.

Causes
It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. It is conceivable that the registry information was damaged or deleted.

Remedies
Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Check settings. Check settings.

Remarks

60050 FFCustomMsgBox 60051 FFCustomMsgBox 60052 FFCustomMsgBox 60053 FFCustomMsgBox 60054 FFCustomMsgBox 60055 FFCustomMsgBox 60056 FFCustomMsgBox 60057 FFCustomMsgBox 60058 FFCustomMsgBox 60060 FFCustomMsgBox 60061 FFCustomMsgBox 60062 FFCustomMsgBox 60081 FFCustomMsgBox 60100 FFCustomMsgBox 60114 60115 FFCustomMsgBox FFCustomMsgBox

Acquisition of optional information It is conceivable that the registry resulted in a failure. information was damaged or deleted. Failed in obtaining the information It is conceivable that the database file was from the character string damaged or deleted. database. Failed in information acquisition from the system setting database It is conceivable that the database file was damaged or deleted.

Failed in obtaining the information The setup file format was incorrect or the from the system setting file. file could not be read. Failed in setting information to the The setup file format was incorrect or the system setting file. file could not be read. An attempt to write system setup information resulted in a failure. An attempt to access the connection device database resulted in a failure. An attempt to acquire information from the connection device database. An attempt to write necessary data in the connection device database resulted in a failure. Acquisition of menu information failed. It is conceivable that the database file was damaged or deleted.

Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

Failed in obtaining the MPM code. It is conceivable that the database file was damaged or deleted. Failed in obtaining the XCON parameter. An error of unknown cause occurred. Disk consistency check resulted in a failure. Import of patient information resulted in a failure. It is conceivable that the database file was damaged or deleted.

60120 FFCustomMsgBox 60121 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-326

Appx MT1-327
Event Event Source Description
[60130] Failed in accessing the preset setting database. *Contact your service engineer. +Press the button below to finish the system. 60131 FFCustomMsgBox [60131] Failed in operation of the preset information. The following reason is presumable. 1. Database access error *Restart the server computer. >Contact your service engineer if restarting of the computer does not resolve the problem. 60203 FFCustomMsgBox 60205 FFCustomMsgBox 60215 FFCustomMsgBox 60220 FFCustomMsgBox Failed in accessing the requesting It is conceivable that the database file was department database. damaged or deleted. Failed in information acquisition from the system setting database Failed in accessing the film annotation database. Failed in reading marker images. It is conceivable that the database file was damaged or deleted. It is conceivable that the database file was damaged or deleted. A problem has occurred for the database (SQL-Server).

Causes
A problem has occurred for the database (SQL-Server).

Remedies
Restart the server application and client application. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

60130 FFCustomMsgBox

Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation. Restart. If the same symptom recurs, perform a reinstallation.

A marker which cannot be displayed exists Confirm the contents of the image data existing in the following folder and make on the marker setting window of the user sure that there are no broken image data. utility. C:\ProgramData\FujiFilm\Hobbit\ UserMarker Addition of a user marker failed on the marker setting window of the user utility. Confirm that the image data of the image which could not be added are supported (only BMP type). Create the image data again and retry.

60221 FFCustomMsgBox

Failed in reading additional images. The data for image processing parameter is invalid.

60251 FFCustomMsgBox 60260 FFCustomMsgBox 60261 FFCustomMsgBox 60262 FFCustomMsgBox 60263 FFCustomMsgBox 60264 FFCustomMsgBox 60300 FFCustomMsgBox
020-221-02E 01.08.2010 FM5563

The CR-IR 391CL system has not The CR-IR 391CL executable file might be been rebooted. damaged or deleted. An error occurred when creating a distribution file. An error occurred when creating a distribution file. An error occurred when creating a distribution file. An error occurred when decompressing a CAB format file for distribution. Failed in accessing the database.

Reinstall the system.

CR-IR 391CL Service Manual

Appx MT1-327

Appx MT1-328
Event Event Source Description
Illegal parameter. The error occurred in the UDF library.

Causes
Parameter is illegal. An error occurred in the UDF library.

Remedies
System settings may have been performed improperly. Check the system settings and retry processing. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. System settings may have been performed improperly. Check the system settings and retry processing. No media have been inserted into drive. Insert media to be formatted, into drive. Then, retry formatting. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the server application and client application. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

60300 FFUdfFmtTool 60301 FFUdfFmtTool

60302 FFUdfFmtTool 60302 FFUdfFmtTool 60302 FFUdfFmtTool

Program error. Specified drive can not use. Program error. Media have not been inserted. Program error. Sequence error.

The specified drive cannot be used. No media have been inserted into drive. A sequence error occurred.

60303 FFUdfFmtTool

Exception error.

An exceptional error occurred during disk format processing.

60307 FFCustomMsgBox 60308 FFCustomMsgBox 60313 FFCustomMsgBox 60314 FFCustomMsgBox 60315 FFCustomMsgBox 60316 FFCustomMsgBox 60320 FFCustomMsgBox

An error occurred during user authentication processing. An error occurred during user authentication processing. The system cannot be started because the server application has already been up and running. The system cannot be started because the User Utility has already been up and running. The system cannot be started because the Service Utility has already been up and running. The system cannot be started because the Backup Utility has already been up and running. Failed in accessing the character string database. Exit the server application, and then retry. Exit the User Utility, and then retry. Exit the server application, and then retry. Exit the Backup Utility, and then retry.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-328

Appx MT1-329
Event Event Source Description
Failed in accessing the system setting database. Failed in obtaining the registry information. An attempt to access the connection device setup database resulted in a failure. Failed in information acquisition from the system setting database Failed in obtaining the information from the system setting file. Database optimization resulted in a failure. Data backup processing was disabled. Data backup processing failed. Creation of a work folder resulted in a failure. An attempt to delete a work folder resulted in a failure. An attempt to acquire information from the list of files targeted for backup processing resulted in a failure. Decompression of a CAB format file resulted in a failure. An attempt to acquire information from the backup version file resulted in a failure. Format processing failed. Failed in obtaining the button image (Urgent button). [60384] Monitor model could not be added. *Check the content of LUT Information File. 60385 FFCustomMsgBox [60385] %s The contents of the LUT information file may be wrong or destroyed.
Change the LUT information file and try again. If the situation does not improve or in case of reoccurrence, confirm the occurrence situation and send the event log and the LUT information file to the manufacturer.

Causes

Remedies

Remarks

60321 FFCustomMsgBox 60322 FFCustomMsgBox 60323 FFCustomMsgBox 60325 FFCustomMsgBox 60326 FFCustomMsgBox 60329 FFCustomMsgBox 60351 FFCustomMsgBox 60352 FFCustomMsgBox 60360 FFCustomMsgBox 60361 FFCustomMsgBox 60370 FFCustomMsgBox

Contact your service engineer.

60371 FFCustomMsgBox 60372 FFCustomMsgBox 60382 FFCustomMsgBox 60383 FFCustomMsgBox 60384 FFCustomMsgBox

An error with unknown cause has occurred Confirm the occurrence situation and send at the service utility monitor type selection the contents listed after the number and the window. event log to the manufacturer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-329

Appx MT1-330
Event Event Source Description Causes Remedies Remarks
60385 ServiceUtility Confirm that the lut.txt listing is correct. If the same error occurs with correct listing, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Invalid Monitor ID: Incorrect monitor ID information has been Confirm that the lut.txt listing is correct. If (MonitorID: ) read in. the same error occurs with correct listing, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Invalid LUT ID: Incorrect LUTID information has been read Confirm that the lut.txt listing is correct. If (MonitorID: ) in. the same error occurs with correct listing, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Invalid LUT Interpretation: Incorrect LUT color space information has Confirm that the lut.txt listing is correct. If (MonitorID: ) been read in. the same error occurs with correct listing, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. The last LUT Interpretation is The LUT color space information is not Confirm that the lut.txt listing is correct. If complemented: sufficient. the same error occurs with correct listing, (MonitorID: ) perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. The monitor name is already used: An already existing monitor name has been Confirm that the lut.txt listing is correct. If read in. the same error occurs with correct listing, (MonitorID: ) perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. LUT Interpretation is The LUT color space has not been Confirm that the lut.txt listing is correct. If complemented: specified. the same error occurs with correct listing, (MonitorID: ) perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Insufficient number of elements: The number of lut.txt elements is not (MonitorID: ) sufficient.

60385 ServiceUtility

60385 ServiceUtility

60385 ServiceUtility

60385 ServiceUtility

60385 ServiceUtility

60385 ServiceUtility

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-330

Appx MT1-331
Event Event Source Description
No LUT file specified: (MonitorID: )

Causes
The LUT file does not exist.

Remedies
Confirm that the lut.txt listing is correct. If the same error occurs with correct listing, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

60385 ServiceUtility

60390 FFCustomMsgBox 60401 FFCustomMsgBox 60402 FFCustomMsgBox 60410 FFCustomMsgBox 60411 FFCustomMsgBox

An attempt to delete target logs failed. Data restoring failed. Data restoring failed. Creation of a work folder resulted in a failure. An attempt to delete a work folder resulted in a failure. An attempt to acquire information from the list of files targeted for backup processing resulted in a failure. Decompression of a CAB format file failed. File restore is not possible because no backup information file exists. The backup information file is illegal. The type of application used for the backup information file is different from that used for the system that is currently up and running. The software version used is different and is not compatible with the backed up file. Collection of logs for maintenance purposes was disabled. Log collection for maintenance purposes resulted in a failure. Creation of a work folder resulted in a failure. An attempt to acquire information from the list of files targeted for backup processing resulted in a failure. Contact your service engineer. Check the backup file, and then retry. Check the backup file, and then retry. Check the backup file, and then retry. Contact your service engineer.

60420 FFCustomMsgBox

60421 FFCustomMsgBox 60426 FFCustomMsgBox 60427 FFCustomMsgBox 60429 FFCustomMsgBox

60430 FFCustomMsgBox 60451 FFCustomMsgBox 60452 FFCustomMsgBox 60460 FFCustomMsgBox 60470 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-331

Appx MT1-332
Event Event Source Description
Decompression of a CAB format file failed. Format processing failed. An attempt to update the volume label of backup disk failed. An attempt to update the volume label failed. Startup of Notepad failed. Retry Notepad startup. If the condition does not improve, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Retry README.TXT creation. If the condition does not improve, confirm the situation in which the error occurred, and submit the event log to the manufacturer. When Private information is not deleted is selected, handle the collected logs carefully because they contain private information. Obtain the maintenance log, and send the %s: Code that shows error details. maintenance log and the encountered error Private information is not included in code (%s) to the manufacturer. created Backup.ini, MAINTENANCE. cab and Study.txt. Confirm the situation in which the error occurred, and submit the obtained maintenance log and an error report to the manufacturer.

Causes

Remedies

Remarks

60471 FFCustomMsgBox 60482 FFCustomMsgBox 60483 FFCustomMsgBox

60495 FFCustomMessageBox An error occurred.

60496 FFCustomMessageBox An error occurred.

Creation of README.TXT failed.

60520 FFCustomMsgBox

Acquisition of the number of registered items has failed. An error has occurred. Error Code: %s Output of study information has failed. Failed in accessing the system setup database. An attempt to write system setup information resulted in a failure. Database Update Error. An attempt to acquire connection device setup information resulted in a failure. Database Update Error. An attempt to write person name setup information resulted in a failure. No available LUT files are found. Free space available on the disk targeted for data storage is insufficient. Database Access Error.

It is conceivable that the database file was damaged or deleted. The personal information deletion process was not successfully performed. The study information for presentation was not successfully output. It is conceivable that the database file was damaged or deleted.

60521 FFCustomMsgBox

60522 FFCustomMsgBox

60600 FFCustomMsgBox 60601 FFCustomMsgBox 60602 FFCustomMsgBox

An attempt to acquire connection equipment setup information. An attempt to write connection equipment setup information.

60603 FFCustomMsgBox

60604 FFCustomMsgBox 60605 FFCustomMsgBox 60606 FFCustomMsgBox

An attempt to acquire character string information resulted in a failure.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-332

Appx MT1-333
Event Event Source Description Causes Remedies Remarks
60607 FFCustomMsgBox 60608 FFCustomMsgBox 60609 FFCustomMsgBox 60610 FFCustomMsgBox 60611 FFCustomMsgBox Database Access Error. An attempt to acquire values from the An attempt to acquire values from database resulted in a failure. the database resulted in a failure. Database Update Error. An attempt to write data in the database resulted in a failure. An exceptional error occurred. An error occurred during termination processing. Settings for services to be distributed resulted in a failure. Failed in accsessing the file. A SQL error occurred. An exceptional error occurred. Failed in obtaining the registry information. Necessary files do not exist. Initialization of the patient database failed. Initialization of the output queue failed. [60629] Initialization of the preset database failed. *Contact your service engineer. 60630 FFCustomMsgBox 60631 FFCustomMsgBox Initialization of the image database failed. An attempt to acquire information of how many times the IP was subjected to X-ray exposure resulted in a failure. An attempt to delete information of how many times the IP was subjected to X-ray exposure resulted in a failure. An attempt to copy the EDR backup data file resulted in a failure. The selected EDR backup data file cannot be found. Acquisition of information on the IP exposure count failed. Deletion of information on the IP exposure count failed. A problem has occurred for the database (SQL-Server). Restart the server application and client application. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Writing of the database failed.

60620 FFCustomMsgBox 60623 FFCustomMsgBox 60624 FFCustomMsgBox 60625 FFCustomMsgBox 60626 FFCustomMsgBox 60627 FFCustomMsgBox 60628 FFCustomMsgBox 60629 FFCustomMsgBox

60632 FFCustomMsgBox

60640 FFCustomMsgBox 60641 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-333

Appx MT1-334
Event Event Source Description
Generation of film annotation characters failed. Generation of film annotation characters failed. An attempt to automatically generate a film format definition file resulted in a failure. Next window could not be displayed. Previous window could not be displayed. The window could not be displayed. Failed in acquiring the Start status. Failed in acquiring the data. Failed in storing the values set. The next window could not be displayed. Restart. If the same symptom recurs, update the startup folder (refer to Event 60721) and perform setup from the Service Utility.

Causes

Remedies

Remarks

60642 FFCustomMsgBox 60643 FFCustomMsgBox 60644 FFCustomMsgBox 60713 FFCustomMsgBox

60714 FFCustomMsgBox

The previous window could not be opened. Restart. If the same symptom recurs, update the startup folder (refer to Event 60721) and perform setup from the Service Utility. The window could not be opened when the Restart. If the same symptom recurs, installation wizard was started. update the startup folder (refer to Event 60721) and perform setup from the Service Utility. The status of the installation wizard could not be acquired from the registry. Restart. If the same symptom recurs, update the startup folder (refer to Event 60721) and perform setup from the Service Utility.

60715 FFCustomMsgBox

60716 FFCustomMsgBox

60717 FFCustomMsgBox 60718 FFCustomMsgBox

The system setup database file or network Restart. If the same symptom recurs, setup database file might be damaged or perform a reinstallation. deleted. The system setup database file or network Restart. If the same symptom recurs, perform a reinstallation. setup database file was not successfully updated. This error is attributable to database file alteration during installation wizard execution or a database file abnormality. The end status of the installation wizard could not be stored. An unexpected window may open the next time the installation wizard is started. Perform a reinstallation. Restart and then perform setup again. If the same symptom recurs, change the startup folder (refer to Event 60721) and perform setup from the Service Utility.

60719 FFCustomMsgBox 60720 FFCustomMsgBox

Failed in storing the End status.

Failed in updating the setting files. An error occurred when an attempt was made to create a distribution file.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-334

Appx MT1-335
Event Event Source Description
Failed in updating the settings for automatic startup.

Causes
The startup folder could not be updated.

Remedies
Change the contents of the C:\Users\ Fujicr\AppData\Roaming\Microsoft\ Windows\Start Menu\Programs\Startup folder as directed below: Delete the shortcut file named SetWiz. Copy and paste the shortcut file named FCR from C:\Users\Public\Public Desktop. Check for a remaining floppy disk or CD in the PC.

Remarks
This error is not used.

60721 FFCustomMsgBox

60753 SetWiz

ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

The disk drive status could not be confirmed.

%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

60756 SetWiz

ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

Failed in reading a file.

Refer to the detailed information and %1= Error Code: The code that uniquely determine the file status that resulted in the identifies an error. error. If the file is normal, abort the %2= Subsystem: The subsystem where an installation wizard and then restart the PC. error occurred. If the same symptom recurs, perform a %3= Source File: The program file where reinstallation. an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other) Abort the installation wizard and then This error is not used. restart the PC. If the same symptom recurs, perform a reinstallation. If the check sheet file is not needed, it is not necessary to take remedial action. Abort the installation wizard and restart the %1= Error Code: The code that uniquely PC. If the same symptom recurs, perform a identifies an error. reinstallation. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

60757 SetWiz

ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

The check sheet file (C:\ProgramData\ FujiFilm\Hobbit\Config\SetwizCheckSheet. txt) could not be created. A character string was not successfully acquired from the character string database. The database file might be damaged or deleted.

60760 SetWiz

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-335

Appx MT1-336
Event Event Source Description
ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

Causes

Remedies

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other) %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other) %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other) %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

60761 SetWiz

The system setup database file or network Restart. If the same symptom recurs, setup database file was not successfully perform a reinstallation. updated. This error is attributable to database file alteration during installation wizard execution or a database file abnormality.

60762 SetWiz

ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

The settings were not successfully acquired or updated.

Abort the installation wizard and then restart the PC. If the same symptom recurs, change the startup folder (see Event 60721) and perform setup from the Service Utility.

60771 SetWiz

ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

It is conceivable that the registry information about the option key or application key is damaged or deleted.

Restart. If the same symptom recurs, perform a reinstallation.

60780 SetWiz

ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

A subprocess was not successfully started up.

Abort the installation wizard and then restart the PC. If the same symptom recurs, change the startup folder (see Event 60721) and perform setup from the Service Utility.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-336

Appx MT1-337
Event Event Source Description
ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

Causes
The check sheet file (C:\ProgramData\ FujiFilm\Hobbit\Config\SetwizCheckSheet. txt) could not be displayed.

Remedies

Remarks

60781 SetWiz

Manually open the file indicated at left. This error is not used. If you cannot open the file, restart. If the same symptom recurs, perform a reinstallation. If the check sheet file is not needed, it is not necessary to take remedial action. Abort the installation wizard and restart the %1= Error Code: The code that uniquely PC. If the same symptom recurs, perform a identifies an error. reinstallation. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other) Abort the installation wizard and then restart the PC. If the same symptom recurs, change the startup folder (see Event 60721) and perform setup from the Service Utility. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

60792 SetWiz

The custom message box could not be displayed.

60799 SetWiz

ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

An error occurred when an attempt was made to start or exit the application.

61060 FFCustomMsgBox 61082 FFCustomMsgBox 61083 FFCustomMsgBox 61084 FFCustomMsgBox 61085 FFCustomMsgBox 61093 FFCustomMsgBox 61094 FFCustomMsgBox 61103 FFCustomMsgBox

Password entered is incorrect. No menu has been selected. Already registered for displaying and cannot be deleted. It is registered with the study menu. It cannot be deleted. A display group with no menus registered for displaying exists. Display group will be deleted. Display group name is illegal. Same extension menu code already exists.

An incorrect password was entered.

The password is fixed at 1111.

An attempt was made to perform an edit or Make a menu selection before performing other operation without making a menu an edit or other operation. selection. The menu could not be deleted because it was registered for display. The menu cannot be deleted because it is registered in the study menu. Clear the registration for display and then delete the menu. Delete the menu from the study menu, and then retry.

This window opens for confirmation only. The entered data was abnormal due, for instance, to its excessive length or the inclusion of an unacceptable character. The entered data value was already registered or otherwise unacceptable. Make a proper entry. Input another extension menu code.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-337

Appx MT1-338
Event
61106 61109 61110 61111 61112 61122 61125 61130 61131 61132 61142 61149 61151 61153 61154 61155

Event Source
FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Description
Same exposure menu name already exists.

Causes
The entered data value was already registered or otherwise unacceptable.

Remedies
Input another ANK exposure menu. Input another kanji-exposure menu name. Make a proper entry. Make a proper entry. Make a proper entry. Make a proper entry. Input another film annotation. Make a proper entry. Make a proper entry. Make a proper entry. Input another study menu code.

Remarks

Same kanji-exposure menu name The entered data value was already already exists. registered or otherwise unacceptable. Extension menu code is illegal. Study menu code is illegal. Kanji-exposure menu name is illegal. MPM code is illegal. Same film annotation already exists. Manufacturer/Equipment Code is illegal. Film-related code is illegal. Auto. Exp. Control is illegal. Same study menu code already exists. No exposure menu has been selected. Exposure menu cannot be registered. Study menu code is illegal. Study menu code is illegal. Kanji-study menu code is illegal. The entered data was abnormal due, for instance, to its excessive length or the inclusion of an unacceptable character. The entered data was abnormal due, for instance, to its excessive length or the inclusion of an unacceptable character. The entered data was abnormal due, for instance, to its excessive length or the inclusion of an unacceptable character. The entered data was abnormal due, for instance, to its excessive length or the inclusion of an unacceptable character. The entered data value was already registered or otherwise unacceptable. The entered data was abnormal due, for instance, to its excessive length or the inclusion of an unacceptable character. The entered data was abnormal due, for instance, to its excessive length or the inclusion of an unacceptable character. The entered data was abnormal due, for instance, to its excessive length or the inclusion of an unacceptable character. The entered data value was already registered or otherwise unacceptable.

An attempt was made to perform an edit or Select a menu and then perform edit other operation without making a menu processing. selection. The maximum permissible number of menu Delete any unnecessary menu. registrations was exceeded. The entered data was abnormal due, for instance, to its excessive length or the inclusion of an unacceptable character. The entered data was abnormal due, for instance, to its excessive length or the inclusion of an unacceptable character. The entered data was abnormal due, for instance, to its excessive length or the inclusion of an unacceptable character. Make a proper entry. Make a proper entry. Make a proper entry.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-338

Appx MT1-339
Event
61156 61160 61161 61170 61171 61211

Event Source
FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox FFCustomMsgBox

Description

Causes

Remedies
The energy subtraction menu cannot be incorporated in the study menu. Input the direction of columns. Input direction of rows.

Remarks

The energy subtraction menu An attempt was made to register the cannot be registered for the study energy subtraction menu in the study menu. menu. No direction of columns has been input. No direction of rows has been input. Because modality is different, it cant be registered for the study menu. No technician code has been input. No film annotation characters have been input. An attempt was made to register data with an input field left blank. An attempt was made to register data with an input field left blank.

Enter a value. Enter a value. Make a proper entry.

61212 FFCustomMsgBox 61213 FFCustomMsgBox 61214 FFCustomMsgBox 61260 FFCustomMsgBox 61270 FFCustomMsgBox 61280 FFCustomMsgBox 61281 FFCustomMsgBox 61282 FFCustomMsgBox 61290 FFCustomMsgBox 61291 FFCustomMsgBox 61302 FFCustomMsgBox 61310 FFCustomMsgBox 61313 FFCustomMsgBox

Film annotation characters are too The entered data was too long. long.

Invalid characters have been input An unacceptable character was contained. Make a proper entry. in the film annotation characters. Same film annotation already exists. Acquisition of path information failed. Already registered for the default menu and cannot be deleted No Coding Scheme Designator has been input. Data is not input. Input correctly. Make a proper entry. The entered data value was already registered or otherwise unacceptable. Input another film annotation.

Coding Scheme Designator is too The entered data was too long. long.

Invalid characters have been input An unacceptable character was contained. Make a proper entry. in Coding Scheme Designator. Patient information maintenance cannot be performed. Set up again so that CR study images are stored on the image storage disk or printing film. An error of unknown cause occurred. No direction of columns has been input. No direction of rows has been input. Input the direction of columns. Input direction of rows. The honorific title used is inappropriate.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-339

Appx MT1-340
Event Event Source Description
Because modality is different, it cant be registered for the study menu. It is registered for the DX parameter of the exposure menu. It cant be deleted. Content of the title of respect prefixed to a patient name is not appropriate. The disk status is abnormal. Sameness of the source and destination for copying data could not be verified. An attempt to successfully finish copy processing resulted in a failure. The source drive for copying data has not been connected or does not exist. The destination drive for copying data has not been connected or does not exist. No format type has been specified for this drive. The setting of the source drive for copying data is incorrect. The setting of the destination drive for copying data is incorrect. It cannot be started because the same application has already been up and running. It cannot be started because the server application has already been up and running. It cannot be started because the User Utility has already been up and running. It cannot be started because the Backup Utility has already been up and running. No available LUT files are found. Retry. Confirm the connection of the source drive of diskcopy. Confirm the connection of the source drive of diskcopy. Insert a formatted blank disk into the drive. Contact your service engineer. Contact your service engineer. To delete it, deregister it from the DX parameter. The honorific title is not input or characters Re-input correctly. that cannot be used are included.

Causes

Remedies

Remarks

61328 FFCustomMsgBox 61329 FFCustomMsgBox 61400 FFCustomMsgBox 61502 FFCustomMsgBox 61505 FFCustomMsgBox 61507 FFCustomMsgBox 61508 FFCustomMsgBox 61509 FFCustomMsgBox 61510 FFCustomMsgBox 61511 FFCustomMsgBox

61512 FFCustomMsgBox 61600 FFCustomMsgBox 61601 FFCustomMsgBox 61602 FFCustomMsgBox 61603 FFCustomMsgBox 61604 FFCustomMsgBox

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-340

Appx MT1-341
Event Event Source Description
Free space available on the disk targeted for data storage is insufficient. There are no data that can be acquired. Free space available on the disk targeted for data storage is insufficient. Update processing is disabled because a serious error occurred. The server application is up and running. The server application is up and running. No monitor models could be added. An attempt was made to start the installation wizard while the server application was running. An attempt was made to start the installation wizard while the server application was running. The probable causes are as follows: Lut.txt is illegal or not found. The lut file is not found on the floppy disk. The lut file having the same name already exists on the PC. A control panel folder or other nonselectable folder was selected. The disk drive status could not be confirmed. Exit the server application and then start the installation wizard. Exit the server application and then start the installation wizard. If there is no problem with the floppy disk or lut file, exit the installation wizard and then correct the settings with the Service Utility. Select a different folder. Check for a remaining floppy disk or CD in the PC. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other) %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

Causes

Remedies

Remarks

61605 FFCustomMsgBox 61606 FFCustomMsgBox 61607 FFCustomMsgBox 61620 FFCustomMsgBox 61700 FFCustomMsgBox 61701 FFCustomMsgBox 61710 FFCustomMsgBox

61722 FFCustomMsgBox 61753 SetWiz

This folder cannot be selected. ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

61793 SetWiz

ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

The window position/size cannot be adjusted.

Manually adjust the window position/size. If you feel uncomfortable, perform a reinstallation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-341

Appx MT1-342
Event Event Source Description Causes Remedies
Change the image size to 1000 x 1000 pixels or less and try again.

Remarks

62200 FFCustomMsgBox

Size of the image to be registered The size of the image to be registered to a to marker is larger than marker exceeds 1000 x 1000 pixels. 1000x1000pixel. This warning message is displayed when 1000 pixels are exceeded in horizontal or vertical direction. Total number of marker images registered exceeds the number allowed by the System Setting.

62201 FFCustomMsgBox

The number of user marker registrations Delete registered user markers and exceeds the system set value (default: 50). register again. Change the following system set value of the service utility. 15-5: Max. number of marker registrations (max. 128) When the client application can be started: If the same error occurs every time the client application is started, manually collect event logs of the client PC, and then contact the manufacturer. When the client application is disabled to start: Check to see that the server application is up and running. Check also to see that the host name of the server PC determined to be target for link of the shortcut icon is correct. If the same problem recurs, contact the manufacturer. If this same error occurs every time the client application is started, manually collect event logs of the client PC, and then contact the manufacturer. If the same error occurs every time the client application is started, manually collect event logs of the client PC, and then contact manufacturer.

62523 LogUpload

An attempt to find log files to be collected ErrorCode: 26002523 resulted in a failure. SubSystem: LogFileUpload FileName: LogUpload.exe SpotCode: 523 ErrorMessage: The failure of pass acquisition

62524 LogUpload

ErrorCode: 26002524 SubSystem: LogFileUpload FileName: LogUpload.exe SpotCode: 524 ErrorMessage: The failure of making temporary folder ErrorCode: 26002525 SubSystem: LogFileUpload FileName: LogUpload.exe SpotCode: 525 ErrorMessage: The failure of file movement ErrorCode: 26002526 SubSystem: LogFileUpload FileName: LogUpload.exe SpotCode: 526 ErrorMessage: The failure of file compression

Creation of the operation folder failed. The program may possibly be defective.

62525 LogUpload

It was not possible to collect log files of the client PC. An attempt to find log files to be collected resulted in a failure or another program is being used.

62526 LogUpload

An attempt to compress a file resulted in a If the same error occurs every time the failure. client application is started, manually Collection of log files may have been failed. collect event logs of the client PC, and then contact manufacturer.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-342

Appx MT1-343
Event Event Source Description
ErrorCode: 26002527 SubSystem: LogFileUpload FileName: LogUpload.exe SpotCode: 527 ErrorMessage: The failure of file upload

Causes
File upload failed.

Remedies
Check to see that the server application is up and running. Check also to see that the host name of the server PC determined to be target for link of the shortcut icon is correct. If the same error occurs every time the client application is started, manually collect event logs of the client PC, and then contact manufacturer. Check to see that the server application is up and running. Check also to see that the host name of the server PC determined to be target for link of the shortcut icon is correct. If the same problem recurs, contact the manufacturer. Restart the OS. If the same error recurs, contact the manufacturer.

Remarks

62527 LogUpload

62528 LogUpload

ErrorCode: 26002528 SubSystem: LogFileUpload FileName: LogUpload.exe SpotCode: 528 ErrorMessage: The failure of Capsula client application start ErrorCode: 26002529 SubSystem: LogFileUpload FileName: LogUpload.exe SpotCode: 529 ErrorMessage: The failure of LogUpload.exe start Settings for the server computer has not been finished. Image Link cannot be set up. [62666] Preset database is initialized. +Are you sure? Folder used by the system cannot be specified. The folder path has already been set up for another purpose. Failed in drive setting of the client PC.

It was not possible to start up the client application.

62529 LogUpload

It was not possible to start up the LogUpload.exe file.

62657 FFCustomMsgBox 62666 FFCustomMsgBox

Perform settings for the server computer. Nothing particular.

62670 FFCustomMsgBox 62671 FFCustomMsgBox 62693 FFCustomMsgBox

Specify another folder. Specify another folder. Disk operation (change, removal) has failed with the client utility or with indicator disk setting. This error may be occurred when increasing client PCs. Try again. If there is no improvement, check the network cable connection. If the above check does not result in improvement, review the client device settings of the service utility. If it is intended, click the OK button. If not, click the cancel button.

62694 FFCustomMsgBox

[62924] The setting of the selected Confirmation to delete the NAS setting. device will be deleted. +Are you sure?

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-343

Appx MT1-344
Event Event Source Description
ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

Causes
The disk tray could not be opened.

Remedies
Manually open the disk tray.

Remarks
%1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

62750 SetWiz

62770 SetWiz

ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

The font information was not successfully acquired.

Although displayed characters might %1= Error Code: The code that uniquely become displaced, there is no operational identifies an error. problem. If you feel uncomfortable, perform %2= Subsystem: The subsystem where an a reinstallation. error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other) The operation log cannot be stored. %1= Error Code: The code that uniquely Restart. If the same error recurs, perform a identifies an error. reinstallation. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other) Although a displayed image may be abnormal due, for instance, to a grayed portion, there is no operational problem. If you feel uncomfortable, perform a reinstallation. %1= Error Code: The code that uniquely identifies an error. %2= Subsystem: The subsystem where an error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other)

62790 SetWiz

ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

The operation log was not successfully written.

62793 SetWiz

ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

Displayed colors could not be adjusted.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-344

Appx MT1-345
Event Event Source Description
ErrorCode : %1%nSubSystem : %2%nSourceFile : %3%nSpotCode : %4%nMessage : %5%n

Causes
The image could not be displayed.

Remedies

Remarks

62794 SetWiz

Although images may be improperly %1= Error Code: The code that uniquely displayed, there is no operational problem. identifies an error. If you feel uncomfortable, perform a %2= Subsystem: The subsystem where an reinstallation. error occurred. %3= Source File: The program file where an error occurred. %4= Spot Code: The location where an error actually occurred (a unique value within the program). %5= Detailed information of an error (details of the cause, location of occurrence, reason of occurrence, and other) Change the preset name and then retry the operation.

64090 FFCustomMsgBox

[64090] Preset of the same name has already been registered. *Change the preset name and then re-execute.

Register an existing preset name at the user utility window.

64200 FFCustomMsgBox 64310 FFUdfFmtTool 64612 FFCustomMsgBox 67053 SetWiz

Markers selected will be deleted. Complete format. [64612] Initialization of the Preset Database has been completed.

This confirmation dialog is displayed when marker deletion has been specified with marker setting of the user utility. File formatting was completed normally. No particular action needs to be taken. Nothing particular. Restart the installation wizard. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the installation wizard. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Confirm that the lut.txt listing is correct. If the same error occurs with correct listing, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Exceptional error (message output Instance generation processing has failed. by OS).

67056 SetWiz

Exceptional error (message output A program error occurred. by OS).

67060 SetWiz

Invalid moniter ID : (MonitorID : )

Monitor ID retrieval processing has failed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-345

Appx MT1-346
Event Event Source Description
Invalid LUT type : (MonitorID : )

Causes
LUT type retrieval processing has failed.

Remedies
Confirm that the lut.txt listing is correct. If the same error occurs with correct listing, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Confirm that the lut.txt listing is correct. If the same error occurs with correct listing, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Confirm that the lut.txt listing is correct. If the same error occurs with correct listing, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Confirm that the lut.txt listing is correct. If the same error occurs with correct listing, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer. Restart the installation wizard. If the same error recurs, perform a reinstallation. If the reinstallation does not help, confirm the situation in which the error occurred, and submit the event log to the manufacturer.

Remarks

67060 SetWiz

67060 SetWiz

Invalid pixel size : (MonitorID : )

Pixel number retrieval has failed.

67060 SetWiz

Invalid LUT ID : (MonitorID : )

LUTID retrieval has failed.

67060 SetWiz

Invalid LUT interpretation : (MonitorID : )

Incorrect LUT color space information has been read in.

67060 SetWiz

Exceptional error (message output A program error occurred. by OS).

100000 FFCustomMsgBox 100002 FFCustomMsgBox 100003 FFCustomMsgBox 100004 FFCustomMsgBox

A study to which no exclusive registration is possible exists. Exclusive registration is not possible. System logoff System is shut down.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-346

Appx MT1-347
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-347

Appx MT1-348
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MT1-348

MC-I

CR-IR 391CL Service Manual

MC: Checks, Replacement and Adjustment of Parts

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-I

MC-II
Control Sheet
Issue date
04/28/2009 01/08/2010

Revision number
01 02

Reason
New release (FM5535) Revision for software V1.1(B) (FM5563)

Pages affected
All pages 3, 30, 31, 33, 35, 36, 38 to 42, 44, 58 to 61, 63, 64, 68, 69, 72 to 74, 77, 79, 89, 90, Appx MC 2-2, 3, 3-1, 4-1, 5-3, 4, 8, 6-1, 6, 8-1, 9-1 to 4 43, 45 to 57, 62, 65 to 67, 70, 71, 75, 76, 78, 80 to 88

Changes in pagination (FM5563)

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-II

MC-1

1. Reinstalling the OS and the Application

1.1 Installation Flowchart (DELL PC)


Presented below is the procedure used for installing the CR-IR 391CL-AP from the OS. Follow the flowchart to install the CR-IR 391CL.
1.2 Preparation 1.3 Installing and Setting Up the OS 1.4 Setting the Network 1.5 RU Settings 1.6 Installing the SQL Server 1.7 Installing the CR-IR 391CL Software 1.8 Settings by the Simplified Setup Wizard 1.9 IIS Network Virus Protection 1.10 Making Checks Using the Service Utility 1.11 Restoring the CR-IR 391CL Config Data 1.12 Operation Check and Initialization after Installation 1.13 Restoring the CR-IR 391CL Configuration Data (patient information) 1.14 Reconstructing the Image Database

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-1

MC-2 1.2 Preparation


Backing up images
Make a backup copy of images in advance.

4.

Display the Display Style Settings tab by selecting it, and view the display style currently selected and take a note of it.

NOTE
The setting of the button display style cannot be saved by setting-backup operation. It is necessary to be set up manually after reinstallation.

Reviewing the current CR-IR 391CL settings

1.

With a study being selected on the Study List window, click Image Viewer.
The Image Viewer window opens.

2.

Right-click in the middle portion of the window (anywhere on the image).


The right-click menu opens.

MC000158.ai

Making a backup using the Backup Utility


MC000157.ai

Make a backup copy of patient information, setup information, and log information.
For information on how to make a backup using the Backup Utility, see Appendix 1: Backup Utility under MU: Maintenance Utility.

3.

From the right-click menu, select [Toolbar Settings] - [Toolbar Settings].


The Toolbar Settings window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-2

MC-3 1.3 Installing and Setting Up the OS


NOTE
When reinstalling the OS, do not connect mouse and keyboard to the adjacent USB ports. After the completion of OS reinstallation processing, reconnect mouse and keyboard to the specified USB ports. An attempt to reinstall the OS, with its mouse and keyboard connected to the adjacent USB ports, may cause keyboard entries not to be recognized halfway through the OS reinstallation processing.

1.3.1 Installing and Setting Windows Vista


This section describes how to install Windows Vista. The OS is to be installed in the following situations: After HDD replacement After an error occurrence in the OS Items to be readied for OS installation Windows Vista installation DVD (Dell Product Recovery DVD (Windows Vista) contained in the PC box.) Dell Resource DVD (A DVD that stores various drivers.)

Property sheet
OS installation drive Partition/format Regional settings Product key C:\ C drive only (no other partitions will be created.) /NTFS Name FUJIFILM Corporation Organization FUJIFILM Corporation Indicated on the right-hand side of the PC main unit cover. The default settings when shipped from factory CR-IR 391CL: Computer name CVXXXXXXXX (XXXXXXXX: Eight-digit manufacture No.) * Take notes accordingly if changed. Password system Protocol used TCP/IP 172.16.1.20 when shipped from factory. IP address * Take notes accordingly if changed. 255.255.0.0 when shipped from factory. Subnet mask * Take notes accordingly if changed. Used by the work group. Domain or work group (The group name remains the default.) Automatically logged fujicr on username Password system Display color True Color (32-bit) 12801024 (17-inch LCD) Display area 16801050 (20-inch LCD)

IMPORTANT
Before formatting the HDD, make backup copy of image data, if any, as required by the user. Make backup copy of config data (CR-IR 391CL, RU-Config) that stores various CR-IR 391CL and RU settings, ahead of time. When making a backup of the configuration data, check the version of the CR-IR 391CLs application and take a note of it. Use the User Utility function to back up user setup information items (place checkmarks to all items).

Computer name and password

NOTES
If the PC is not connected via the network, the network setup windows will not be displayed while the OS is being installed. To perform network settings, be sure to connect the PC to the network (connection to the RU) accordingly before installation work. When HDD of a recommended PC model is replaced, check setup details ahead of time because the HDD may not be operated unless the PCs BIOS settings are changed accordingly. Driver software installation may be required while Windows Vista is being installed. In such an instance, use the Dell Resource DVD to install it.

Network settings

This computers user settings (auto logon settings) Monitor settings

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-3

MC-4
Network connection between the CR-IR 391CL and the RU
If the PC is not connected properly via the network in advance, the network setup windows will not be displayed while the OS is being installed, depending on the Windows Vista installer specifications.
For details, see 3.4 Connecting a Cable Between the RU and Other Equipment under IN: Installation.

Windows Vista installation


Changing the boot menu setting and starting from the installation DVD

1. 2.

Turn ON the monitor and PC power switches.


The PC starts running.

1. 2.

Use a crossing cable to connect the CR-IR 391CL to the RU or use a network cable to connect the CR-IR 391CL to the HUB for network connection via the HUB. Turn ON the power to the RU. For network connection via the HUB, the power can be left turned OFF.

Press the <F12> key when F12 Boot Options appears at the upper right corner of the window.

NOTE
If the <F12> key is not pressed with the timeliness, the setup window will not open. In such an instance, restart the PC to perform Step 2. above again.
The Boot Device Menu window opens.
Boot Device Menu

Onboard or USB Floppy Drive SATA0-ST3250310AS Onboard or USB CD-ROM Drive System Setup Diagnostics Use Up/Down arrows to highlight desired item. Use Enter to select highlighted item.
MC000108.ai

3.

Insert the Windows Vista installation DVD into the DVD drive.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-4

MC-5
4.
Select Onboard or USB CD-ROM Drive using arrow keys, and press the <Enter> key.
The Press any key to boot from CD or DVD. message appears on the bottom of the window.
Boot Device Menu

6.

Select My language is English.

Onboard or USB Floppy Drive SATA0-ST3250310AS Onboard or USB CD-ROM Drive System Setup Diagnostics Use Up/Down arrows to highlight desired item. Use Enter to select highlighted item. Press any key to boot from CD or DVD.
MC000109.ai AWV22001_E.ai

The language selection window open.

7.

Make the following settings.

5.

Press the <Enter> key within three seconds. NOTE


If you do not press the <Enter> key within about three seconds after the Press any key to boot from the CD or DVD message appears on the bottom of the window, the installation DVD will not be recognized accordingly. If such a failure occurs, restart the PC to perform Step 2. to 4. again.
After a while, the Window Vista window opens.

AWV22002_E.ai

Language to install

: English

Time and currency format : English (United States) Keyboard or input method : US

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-5

MC-6
8.
Click [Next] .
The following window opens.

11. Select Custom (advanced).

AWV22005_E.ai AWV22003_E.ai

9.

The Where do you want to install Windows? window opens.

Click Install now.


The Please read the license terms window opens.

12. Select Drive options (advanced).

10. Place a checkmark to I accept the license terms and click [Next].

CBS03001.ai

AWV22004_E.ai

The Which type of installation do you want? window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-6

MC-7
13. Select Disc 0 Partition 2 RECOVERY and select Delete. 15. Select Disc 0 Partition 2 OS and select Delete.

CBS03002.ai

CBS03003.ai

A confirmation window opens.

A confirmation window opens.

14. Click [OK].

16. Click [OK].

AWV22008_E.ai

AWV22008_E.ai

The system returns to the Where do you want to install Windows? window.

The system returns to the Where do you want to install Windows? window.

17. Click [Next].


The OS Installation processing starts. Upon completion of installation, the Choose a user name and picture window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-7

MC-8
n Windows setup

3.

1.

Make the following settings.

Enter CVxxxxxxxx in the Type a computer name field. (use upper-case characters to enter the CV. xxxxxxxx are for the CV serial number.)

CBS03005.ai

4.
CBS03004.ai

Click

The Help protect Windows automatically window opens.

Type a user name (for example, John) : fujicr Type a password (recommended) Retype your password Type a password hint : system : system : fujicr

5.

Select Ask me later.

NOTE
The character string entries in the Type a password (recommended): and ReType your password: fields appear as l.

2.

Click

AWV22015_E.ai

The Type a Computer name and choose a desktop background window opens.

The Review your time and date settings window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-8

MC-9
6.
Verify the Time zone, Date and Time and click . If the shown Time zone, Date and Time are not correct, change it as appropriate and click .

9.

Enter system and click

AWV32020.ai

NOTE
The password appear as l.
The desktop window opens.
AWV22016_E.ai

The following window opens.

REFERENCE
If the Welcome Center window opens, close the Welcome Center window.

AWV22018_E.ai

7. 8.

Click

After a while, the log-in window opens.

Remove the Operating System (for Re-Install) DVD from the PC.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-9

MC-10
n Setting the User Account Control
Turn off and disable User Account Control from prompting for credentials to install applications, and changing the elevation prompt behavior.

3.

Select User Accounts.

1.

Select Control Panel from the

menu.

AWV22033_E.ai

The Make changes to your user account window opens.

4.

Select Turn User Account Control on or off.

AWV22019_E.ai

The Control Panel window opens.

2.

Select User Accounts.

AWV22034_E.ai

The User Accounts Control window opens.


AWV22032_E.ai

The User Accounts window opens.

5.

Click

AWV22035_E.ai

The Turn User Account Control On or Off window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-10

MC-11
6.
Remove the checkmark from Use User Account Control (UAC) to help protect your computer and click .

8.

Enter system and click

AWV22036_E.ai

The Microsoft Windows window opens.

AWV32020.ai

NOTE
The password appear as l.
The Welcome Center window opens.

AWV22037_E.ai

9.

7.

Click

Remove the checkmark from Run at setup (Welcome Center can be found in Control Panel, System and Maintenance) and close the Welcome Center window.

After the PC restart, the log-in window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-11

MC-12
1.3.2 Installing the Driver Software
For driver software installation, use the utility software on DRIVERS AND UTILITIES ALREADY INSTALLED ON YOUR COMPUTER DVD. To do this, you must first install the utility software on the PC for the CR-IR 391CL.

Installing the Dell Resource DVD utility software

1.

Insert DRIVERS AND UTILITIES ALREADY INSTALLED ON YOUR COMPUTER DVD into the PC.
The AutoPlay window opens.

REFERENCE
To determine what driver software needs to be installed, you can use Device Manager. To open Device Manager, perform the following steps: 1. Right-click Computer from the the pull-down menu that opens. The System window opens. 2. Select Device Manager. The Device Manager window opens. The software for items marked ! in Device Manager is not installed. Install the driver software for such items. menu and select Properties from

2.

Place a checkmark to Always do this for software and games and click Run autoRcd.exe.

CBS03014.ai

The ResourceCD Installation window opens.

3.

Click

AWV22043_E.ai

A new window opens to indicate that the installation wizard is started.

AWV22044_E.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-12

MC-13
4.
Click .

Installing the driver software


Install the following driver software items. System Utilities Controller drivers Video drivers Network drivers Audio drivers

The Ready to Install the Program window opens.

NOTE
AWV22045_E.ai

5.

Click

Since the drivers to be installed vary with the employed PC model and utility software version, confirm the correct drivers by calling Dells Technical Support or visiting associated home page.

The installation processing starts. After a while, the InstallShield Wizard Complete window opens.

Installing the System Utilities

1.

In the System Utilities area, click the Dell System Software Rev:xx.
The System Utilities window opens.

AWV22046_E.ai

6. 7.

Click

A utility program starts to display the initial screen.

Remove the checkmark from Click here to prevent this information from being displayed again. and close the window.

CBS03006.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-13

MC-14
2.
Scroll the display and click [Extract].
The System Utilities-related window opens.

5.

Click [Yes].
A window opens to indicate that decompressing processing is completed.

CBS03010.ai

6.
CBS03007.ai

Click [OK].
The System Softwares setup wizard window opens.

3.

Click [Continue].
A window opens to prompt you to confirm a destination targeted for decompressing the System Software.

CBS03008.ai

4.

Click [OK].
A window opens to prompt you to confirm the folder where the file is to be decompressed.
CBS03011.ai

CBS03009.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-14

MC-15
7.
Click [Next].
The following window opens.

Installing the Controller drivers

1.

In the Controller Drivers area, click the Intel Chipset Software Installation Utility Rev:xxx.
The Controller drivers window opens.

CBS03012.ai

8.

Click [Install].
The System Softwares setup complete window opens.

CBS03015.ai

2.

Scroll the display and click [Extract].


The Controller drivers-related window opens.

CBS03013.ai

9.

Click [Finish].
The system returns to the System Utilities window.

CBS03016.ai

10. Click [Return].


020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-15

MC-16
3.
Click [Continue].
A window opens to prompt you to confirm a destination targeted for decompressing the Controller driver.

6.

Click [OK].
The following window opens.

CBS03017.ai

4.

Click [OK].
A window opens to prompt you to confirm the folder where the file is to be decompressed.

CBS03020.ai

7.
CBS03018.ai

Click [Next].
The License Agreement window opens.

5.

Click [Yes].
A window opens to indicate that decompressing processing is completed.

CBS03019.ai

CBS03021.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-16

MC-17
8.
Click [Yes].
The Readme File Information window opens.

10. Checkmark Yes, I want to restart this computer now., and click
[Finish].
The PC restarts.

11. Enter system as the password. Click

The Dell Resource CD utility software window opens.

CBS03022.ai

9.

Click [Next].
The Controller drivers setup completion window opens.

CBS03023.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-17

MC-18
Installing the Video drivers

3.

Click [Continue].
A window opens to prompt you to confirm a destination targeted for decompressing the Video driver.

1.

In the Video Device Drivers area, click Intel Q43/Q45/G43/G45....

NOTE
If there is no checkmark beside the driver name(s) or there are two or more driver names checkmarked, contact the Dells Technical Support.
The Video drivers window opens.
CBS03026.ai

4.

Click [OK].
A window opens to prompt you to confirm the folder where the file is to be decompressed.

CBS03027.ai

5.
CBS03024.ai

Click [Yes].
A window opens to indicate that decompressing processing is completed.

2.

Scroll the display and click [Extract].


The Video drivers-related window opens.

CBS03028.ai

CBS03025.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-18

MC-19
6.
Click [OK].
The Video drivers setup wizard window opens.

8.

Click [Yes].
The Readme File Information window opens.

CBS03029.ai

CBS03031.ai

7.

Remove the checkmark from automatically run WinSAT... and click [Next].
The License Agreement window opens.

9.

Click [Next].
Installation processing starts. When the Installation processing completes, the window stops with the Click Next to continue is selected.

CBS03030.ai

CBS03032.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-19

MC-20
10. Click [Next].
The Video drivers setup completion window opens.

Installing the Network drivers

1.

In the Network (NIC) Drivers area, click the name of a driver to use (one that is checkmarked).

NOTE
Since the drivers to be installed vary with the employed PC model and utility software version, confirm the correct drivers by calling Dells Technical Support or visiting associated home page.
The Network drivers window opens.

CBS03033.ai

11. Select Yes, I want to restart this computer now. and click [Finish].
The PC restarts.

12. Enter system as the password. Click then

The Dell Resource CD utility software window opens.

CBS03034.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-20

MC-21
2.
Click [Extract].
The Network drivers-related window opens.

5.

Click [Yes].
A window opens to indicate that decompressing processing is completed.

CBS03038.ai

6.
CBS03035.ai

Click [OK].
The Installing Drivers window opens.

3.

Click [Continue].
A window opens to prompt you to confirm a destination targeted for decompressing the Network driver.

CBS03039.ai

7.
CBS03036.ai

Click [Close].

4.

Click [OK].
A window opens to prompt you to confirm the folder where the file is to be decompressed.

CBS03037.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-21

MC-22
Installing the Audio drivers

2.

Click [Extract].
The Audio drivers-related window opens.

1.

In the Audio Drivers area, click the name of a driver to use (one that is checkmarked).

NOTE
If there is no checkmarked driver displayed, contact Dells Technical Support.
The Audio drivers window opens.

CBS03041.ai

3.

Click [Continue].
A window opens to prompt you to confirm a destination targeted for decompressing the Audio driver.

CBS03042.ai

4.
CBS03040.ai

Click [OK].
A window opens to prompt you to confirm the folder where the file is to be decompressed.

CBS03043.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-22

MC-23
5.
Click [Yes].
A window opens to indicate that decompressing processing is completed.

7.

Click [Next].
The Audio drivers setup complete window opens.

CBS03044.ai

6.

Click [OK].
The Audio drivers setup wizard window opens.

CBS03046.ai

8. 9.

Click [Finish].
The system returns to the Audio drivers window.

Close the Dell Resource CD Utility Software window. drive.

10. Remove the DRIVERS AND UTILITIES ALREADY DVD from the DVD

CBS03045.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-23

MC-24
Checking the Device Manager

1. 2. 3.

Select Control Panel from the


The Control Panel window opens.

menu.

Select Hardware and Sound.


The Hardware and Sound window opens.

Click Device Manager.

CBS03047.ai

The Device Manager window opens.

4. 5.

Confirm ! does not appear. Close the Device Manager window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-24

MC-25
1.3.3 Setting the OS
Perform the following OS-related settings. Regional and language options settings Defining the character to be used as a decimal point Setting up the taskbar Checking the monitor settings Windows Sidebar Properties Setting up Power Options Setting up Windows Update Setting up Security Center Setting up Windows Defender Setting up Defragmentation

Regional and language options settings


Prior to performing necessary settings using the Service Utility functions, perform OS settings according to the region where the equipment is to be installed.

1.

Select [Control Panel] from the

menu.

The Control Panel is displayed. If the window is not in the Classic View mode, click Classic View to change the display to Classic View.

2.

Double-click [Regional and Language Options].


The [Regional and Language Options] window opens.

CBS03049.ai

3.

Click the Formats tab to select a language (region) to use from the pull-down menu in Current format.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-25

MC-26
4. 5.
Click [Customize this format].
The [Customize Regional Options] window then opens.

6.

Following examples shown in the table below, enter a date from the keyboard in the [Date formats:] box of the [Short date] field.

Select the Date tab.

CAUTION
A date entered will not be displayed correctly if the order to display year/ month/day used in the CR-IR 391CL system is different from that of the OS date format. Because this is used for important information, including the date of study and the like, it is essential to perform a date setting on the OS side carefully at this step. For details of settings of the date format used in the CR-IR 391CL system, see 5.3 System Settings under MU: Maintenance Utility.
Date format used in the CR-IR 391CL
Japanese date (S62.10.07) ANSI long date (1987.OCT.07) ANSI short date (1987.10.07) American long date (OCT.07.1987) American short date (10.07.1987) European long date (07.OCT.1987) European short date (07.10.1987)

Date format used in the OS short Date format


yy/MM/dd yyyy/MM/dd yyyy/MM/dd MM/dd/yyyy MM/dd/yyyy dd/MM/yyyy dd/MM/yyyy

* Enter directly from the keyboard because some formats are not displayed in the pull-down menu.
CBS03048.ai

7.

Similarly, perform settings for the [Long date] field.

NOTE
When doing so, observe the order of entering year/month/day in the short date format determined at Step 6 above.

8.

Click [Apply].

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-26

MC-27
9.
Select the Time tab.

CBS03050.ai

10. Select [HH:mm:ss] or [H:mm:ss] for the [Time format:] box setting.
CAUTION
Do not use tt representation. The CR-IR 391CL database will not be displayed correctly if [hh:mm:ss tt] or [h:mm:ss tt] is specified for the time format.

11. Click [OK].


The system returns to the [Regional and Language Options] window.

12. Click [OK].


The system returns to the Control Panel.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-27

MC-28
Defining the character to be used as a decimal point
Select . (period) as the character to be used as a decimal point. If anything other than a period is selected, an error occurs when you select an image distribution destination with the QA function.

3.

1.

Check to see that the character specified in the Decimal symbol field is . (period). If not, change it to . (period). If, as a result of the above selection, the same symbol is selected for the Digit grouping symbol and Decimal symbol fields, change the symbol for the Digit grouping symbol field.

In the Control Panel window, double-click Regional and Language Options.


The Regional and Language Options window opens.

2.

Make sure that the Regional Options tab is selected and click [Customize].

CBS03051.ai

CBS03052.ai

The Customize Regional Options window opens.

4. 5.

Click [OK].
The system returns to the Regional and Language Options window.

Click [OK].
The system returns to the Control Panel.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-28

MC-29
Setting up the taskbar
Change the taskbar appearance settings in the following way.

3.

Select Notification Area and remove the checkmark from ). Hide inactive icons (

1.

In the Control Panel window, double-click Taskbar and Start Menu Properties.
The Taskbar and Start Menu Properties window opens.

2.

Place a checkmark to Auto-hide the taskbar (

).

CBS03054.ai

4.

Click [OK].
The system returns to the Control Panel.

CBS03053.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-29

MC-30
Checking the monitor settings

5.

Select Adapter tab and click [List All Modes...].

1. 2. 3.

In the Control Panel window, double-click Display settings.


The Display settings window opens.

Double-click the Personalization.


The Personalization appearance and sounds window opens.

Click Display settings.


The Display Settings window opens.

CBS03084.ai

The List All Modes window opens.

CBS03056.ai CBS03055.ai

4.

Click [Advanced Settings...].

6. 7. 8. 9.

Select 1280 by 1024, True Color (32bit), 60 Hertz and click [OK].
The system return to the Display properties window.

Click [OK].
The system returns to the Display Settings window.

Click [OK].
The system returns to the Personalize appearance and sounds window.

Close the Personalize appearance and sounds window


The system returns to the Control Panel.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-30

MC-31
Windows Sidebar Properties Setting up Power Options

1.

In the Control Panel window, double-click Windows Sidebar Properties.


The Windows Sidebar Properties window opens.

1. 2.

In the Control Panel window, double-click Power Options.


The Power Options Properties window opens.

2.

Remove the checkmark from the Start Sidebar when Windows starts.

Select Balanced and click change plan settings.

CBS03058.ai

3.

Set Turn off the display to 20 minuets and Put the computer to sleep to Never.

CBS03057.ai

3.

Click [OK].
The system returns to the Control Panel.

CBS03059.ai

4. 5.
020-221-02E 01.08.2010 FM5563

Click [Save changes].


The system returns to the Power Options Properties window.

Return to the Control Panel.

CR-IR 391CL Service Manual

MC-31

MC-32
Setting up Windows Update setting Setting up Security Center

1. 2.

In the Control Panel window, double-click Windows update.


The Windows update window opens.

1. 2. 3.

In the Control Panel window, double-click Security Center.


The Windows Security Center window opens.

Click [Change settings].

Click

in the Malware protection.

Click Show me my available options.

CBS03060.ai

The Change settings window opens.

3.

Select Never check for updates (not recommended).


The Choose an antivirus option window opens.

CBS03062.ai

4.

Click [I have an antivirus program that Ill monitor myself].


The system return to the Windows Security Center window.

CBS03061.ai

4. 5.

Click [OK].
The system return to the Windows update window.

Return to the Control Panel.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-32

MC-33
5.
Select Change the way Security Center alerts me.

Setting up Windows Defender

1. 2.

In the Control Panel window, double-click Windows Defender.


The Windows Defender window opens.

Select Tools and click Options.

CBS03063.ai

The Do you want to be notified of security issues? window opens.

6. 7.

Click [Dont notify me and dont display the icon (not recommended)].
The system return to the Windows Security Center window.
CBS03064.ai

Close the Windows Security Center window.

The Options window opens.

3.

Remove the checkmarks from Use Windows Defender and click [Save].

CBS03065.ai

The confirmation window opens.

CBS03066.ai

4. 5.
020-221-02E 01.08.2010 FM5563

Click [Close].
The system returns to the Tools and Settings window.

Close the Tools and Settings window and Control Panel window.
The system returns to the desktop screen.

CR-IR 391CL Service Manual

MC-33

MC-34
Setting up Defragmentation
Disable defrag schedule setting.

3.
menu.

Select Tools tab and select

1.

Select Computer from the

AWV22082_E.ai AWV22080_E.ai

The Computer window opens.

The Disk Defragmenter window opens.

2.

Right-click Local Disk (C:) and select Properties.

4.

Remove the checkmark from Run on a schedule (recommended) and click .

AWV22083_E.ai

The system returns to the Local Disk (C:) Properties window.


AWV22081_E.ai

5. 6.

Click

The Local Disk (C:) Properties window opens.

The system returns to the Computer window.

Close the Computer window.


The system returns to the desktop screen.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-34

MC-35 1.4 Setting the Network


1.4.1 Installing .NET Framework

5.

Double-click dotnetfx.
The installation start confirmation window opens.

1.

Insert the CR-IR 391CL application CD into the DVD drive.

NOTE
In the case of AutoPlay dialog appears, operate according to the following procedures. I. Checkmark Always do this for software and games: and click [Run InstallLauncher.exe].
The Setup window opens.
CBS03068.ai

6.

Click [Yes].
In a while, the License Agreement window opens.

II. Click [Tool Application Setup].


The Select Menu window opens.

III. Click [Open CD Root Folder]. IV. Perform step 4 and later.

2. 3. 4.

Select Computer from the


The Computer window opens.

menu.

Right-click D drive and select open. Open folders in the following sequence: dotNet, DNET1.1, and DNET1.1.
CBS03069.ai

7.

Select the I agree radio button, and click [Install].


Installation processing starts. When the installation completes, the completion window opens.

CBS03067.ai

CBS03070.ai

8.
020-221-02E 01.08.2010 FM5563

Click [OK].

CR-IR 391CL Service Manual

MC-35

MC-36
9.
Open folders in the following sequence: D drive, dotNet, DNET1.1, and DNET1.1SP1.

12. Click [I accept].


Installation processing starts. When the installation completes, the completion window opens.

CBS03074.ai

CBS03071.ai

13. Click [OK]. 14. Restart the PC. 15. When a login window opens after the restart of the PC, enter system
as the password. Click
The desktop window open.

10. Double-click NDP1.1sp1-KB867460-X86.


The confirmation window for starting installation of .NET Framework 1.1 Service Pack 1 opens.

CBS03072.ai

11. Click [OK].


The supplemental end user license agreement window opens.

CBS03073.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-36

MC-37
1.4.2 Setting the IP address
Setting the IP address.

4.

Double-click Local Area Connection.

1.

Select Control Panel from the

menu.

CBS03077.ai

The Local Area Connection Status window opens.

5.
AWV22019_E.ai

Click

The Control Panel window opens.

2.

Double-click

The Network and Sharing Center window opens.

3.

Select Manage network connections.

AWV22050_E.ai

The Local Area Connection Properties window opens.

CBS03076.ai

The Network Connection window opens.


020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MC-37

MC-38
6.
Remove the checkmark from Internet Protocol Version 6 (TCP/IPv6).

8.

Select Use the following IP address and make the following settings.

I. II.

CBS03078.ai

7.

CBS03080.ai

Select Internet Protocol Version 4 (TCP/IPv4) and click

I. Enter the IP address.

(ex. : 172.16.1.20)

II. Enter the Subnet mask. (ex. : 255.255.0.0)

NOTE
Enter the IP address and subnet mask that were noted down before the start of OS installation.

9.

Click

The system returns to the Local Area Connection Properties window.

10. Click
CBS03079.ai

The Internet Protocol Version 4 (TCP/IPv4) Properties window opens.

The system returns to the Local Area Connection Status window.

11. Click

The system returns to the Network Connection window.

12. Close the Network Connection window.


The system returns to the Network and Sharing Center window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-38

MC-39
13. Click
at the Network discovery.

15. Click [Yes, turn on network discovery for all public networks].

MC000418.ai

The system returns to the Network and Sharing Center window.

MC000416.ai

16. Confirm that the Network discovery is On and close the window.
.

14. Select the Turn on network discovery, and click

MC000419.ai

The system returns to the desktop screen.

MC000417.ai

The Network discovery window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-39

MC-40
1.4.3 Adding the Windows Components
Make an additional installation for Windows components.

4.

Put checkmarks for the following items.


ActiveX Installer Service FTP Publishing Service Web Management Tools .NET Extensibility ASP .NET ISAPI Extensions ISAPI Filters Common Http Features HTTP Logging Security XPS Viewer

1.

Select Control Panel from the

menu.

AWV22019_E.ai

Remote Differential Compression Telnet Client Windows DFS Replication Service Windows Process Activation Service

The Control Panel window opens.

2. 3.

Double-click [Programs and Features].


The Uninstall or change a program window opens.

Select Turn Windows features on or off.

AWV22077_E.ai

The Windows Features window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-40

MC-41
NOTE
indicates it is the item to be installed. indicates a part of the items of its lower layer will be installed.

When put a checkmark in its check box, all items of its lower layer will be selected automatically in case there is any lower layer.

5.

Click

Upon completion of installation, the following window opens.

CBS03082.ai

6. 7.

Click [Restart Now].


The PC Restart.

When a login window opens after the restart of the PC, enter system as the password. Click .

CBS03081.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-41

MC-42
1.4.4 Setting the Service (Only for Server PC)

4. 5.

Right-click FTP Publishing Service and select Properties.


The FTP Publishing Service Properties (Local Computer) window opens.

1.

Select Control Panel from the

menu.

Select Automatic from the Startup type: pull-down menu and click [Start] .

AWV22019_E.ai

The Control Panel window opens.

2. 3.

Double-click [Administrative Tools].


The Administrative Tools window opens.
CBS03083.ai

The system returns to the Service window.

Double-click Service.

6. 7. 8.

Click [OK] . Close the Service window.


The system returns to the Administrative Tools window.

Close the Administrative Tools window.


The system returns to the desktop screen

AWV22086_E.ai

The Service window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-42

MC-43 1.5 RU Settings


To perform RU software settings, be sure to observe the procedures shown in the flow below.
1.5.1 Installing the RU PC-TOOL 1.5.2 Setting Up and Checking Firewall Settings 1.5.3 Installing and Registering RU-AP

1.5.1 Installing the RU PC-TOOL


The RU PC-TOOL is a utility (also referred to as the FCR TOOL) that exercises RU-AP installation, RU-Config setup, data backup, and other functions. For the operations of the CR-IR 391CL and RU, it is necessary that the RU PCTOOL be installed in the CR-IR 391CL system.

NOTE
Before installing the RU PC-TOOL, be sure to confirm that User Account Control is turned off.

1.

Insert the RU APL Software CD into the CR-IR 391CLs DVD drive.
The Set Up PC-TOOL window automatically opens.

CBS03084.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-43

MC-44
2.
Click [INSTALL].

4. 5.

Click [OK]. Click [Next].

CBS03085.ai

3.

Select For FTP-Server, and click [SET].

NOTE
Be sure to select For FTP-Server. If For Client PC is selected, installation cannot be done successfully. If you have erroneously selected For Client PC and clicked [SET], perform installation again by following the procedure below. See Appendix 8: Corrective Procedure to be Performed after Improper RU PC-TOOL Installation under IN: Installation of the RU Service Manual.
CBS03087.ai

6.

Click [Install].

CBS03086.ai

The confirmation window opens.

CBS03088.ai

MC000428.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-44

MC-45
7.
When the installation completes, click [Finish].

8.

Press the <Enter> key.


The following window opens.

CBS03089.ai

CBS03091.ai

The following window opens.

9.

Press the <Enter> key.


The Windows Security Alert window opens.

10. Click [Unblock].

CBS03090.ai

CBS03092.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-45

MC-46
11. Click [EXIT].
1.5.2 Setting Up and Checking Firewall Settings

1. 2. 3.

Select Control Panel from the


The Control Panel window opens.

menu.

Double-click [Windows Firewall].


The Windows Firewall window opens.

Select Allow a program through Windows Firewall.

CBS03094.ai CBS03093.ai

12. Remove the RU APL Software CD from the DVD drive, and restart the

The Windows Firewall Settings window opens.

PC. When the OS has started up and the CR-IR 391CLs startup window opens, click in the upper-left corner and then the upper-right corner of the window.
The Service Utilitys authentication window opens.

4.

Click the Exceptions tab.

13. Click [Cancel] to close the window.

CBS03095.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-46

MC-47
5.
Check to see that FTP (File Transfer Protocol) is checkmarked.

6.

Check to see that BmpServer is checkmarked.

CBS03096.ai

CBS03097.ai

If the FTP item does not exist, perform the procedure described later in If FTP does not exist (Adding a program).

If BmpServer does not exist, perform the procedure described later in If BmpServer does not exist (Adding a program).

NOTE
File Transfer Program or ftp may be displayed, instead of FTP.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-47

MC-48
If FTP does not exist (Adding a program)

2.

Click [Browse...].
The Browse window opens.

1.

In the Exceptions tab of the Windows Firewall window, click [Add program...].

CBS03100.ai

3. 4.
CBS03098.ai

Enter C:\WINDOWS\SYSTEM32\FTP in the filename field, and click [Open]. Click [OK] in the Add a Program window.
The system returns to the Exceptions tab in the Windows Firewall window.

The Add a Program window opens.

5.

Make sure that FTP is checkmarked.

NOTE
File Transfer Program or ftp may be displayed, instead of FTP.

CBS03099.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-48

MC-49
If BmpServer does not exist (Adding a program)

2.

Click [Browse...].
The Browse dialog opens.

1.

In the Exceptions tab of the Windows Firewall window, click [Add program...].

CBS03100.ai

3. 4.
CBS03101.ai

Select C:\Program Files\FujiFilm\FCR\TOOL\BmpServer, and click [Open]. Click [OK] in the Add a Program window.
The system returns to the Exceptions tab in the Windows Firewall window.

The Add a Program window opens.

5.

Make sure that BmpServer is checkmarked.

CBS03099.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-49

MC-50
Setting up the FTP port Setting up inetinfo

1.

In the Exceptions tab of the Windows Firewall window, click [Add port].
The Add a Port window opens.

1.

In the Exceptions tab of the Windows Firewall window, click [Add program...].

CBS03102.ai

2. 3. 4.

In the Name: field, enter FTP_port. In the Port number field, enter 21. Click TCP to select it.
The Add a Program window opens.
CBS03098.ai

CBS03103.ai

5.

Click [OK].
The system returns to the Exceptions tab in the Windows Firewall window.

CBS03099.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-50

MC-51
2.
Click [Browse...].
The Browse window opens.

4.

Click [Open].
The system returns to the Add a Program window.

CBS03105.ai

CBS03100.ai

5.

With inetinfo being selected, click [OK].


The system returns to the Windows Firewall window.

3.

In the File name: field, enter C:\WINDOWS\system32\inetsrv\ inetinfo.

CBS03106.ai CBS03104.ai

6. 7.
020-221-02E 01.08.2010 FM5563

Make sure that inetinfo is checkmarked, and click [OK].


The system returns to the Control Panel.

Close the Control Panel window.

CR-IR 391CL Service Manual

MC-51

MC-52
1.5.3 Installing and Registering RU-AP

3.

Click [START].

Installing the RU-AP Software and Restoring the RU-Config


First, install the RU-AP in the CR-IR 391CL, and then restore the RU-Config. To do this, use the RU PC-TOOL and perform the procedures set forth in this section.

NOTE
Before installing the RU-AP, turn ON the RU power.

Installing the RU-AP


REFERENCE
This section describes the procedures, by way of example, where settings are made as follows: INSTALL VERSION : 1.0 LANGUAGE : NONE BRAND TYPE : NONE
CBS03107.ai

4.

Enter RU NAME and RU IP ADDR.

NOTE
Enter the IP address of the RU that has been set on the CR-IR 391CL.

1.

Turn the RU OFF and then turn it ON.

NOTE
Although a connection error occurs on the RU side, it will pose no problem to subsequent work if you simply clear the alarm.
#1[Input] #2[Input]
FRCH7050.ai

2.

Select Computer from the

menu and double-click DVD drive (D:).

5.

Click [PING].
[Click]

FRCH7051.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-52

MC-53
6.
Check the result of PING, and click
#2
CBS03109.ai

to close the window.

8.

Click [OK].

#1 [Check]

9.

Select INSTALL VERSION and click [OK].

0% loss should appear.


CBS03108.ai

[GOOD indication].
If the following message appears, the result is normal. | Ping statistics for 172.16.1.10: | | Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), |
CBS03110.ai

[NO GOOD indication].


Other than above is all abnormal. (The selected IP address of the RU is displayed.)

10. Make sure that INCH is selected for IP Size Code Setting (size
system of the IP used).

NOTE
In the case of NO GOOD indication See MT: Machine Troubleshooting of the RU Service Manual.

7.

Click [INSTALL].
[Click]

CBS03111.ai

FRCH7053.ai

REFERENCE
When clicking on [INSTALL], Under maintenance appears on the operation panel of the RU.

11. If configuration information other than the default settings is used at

the request of the institution, change the settings as described below.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-53

MC-54
12. Click [SET]. 14. Confirm the installation precautions.
CAUTION
While the flash ROM is being written into, never turn OFF the RU or CR Console. If you turn OFF the power, the program stored in the memory becomes damaged and cannot restart.

15. Click [SET].


When you click on [SET], the installation screen opens on the CR Console display. While the flash ROM is being written into, the RUs LED blinks.
CBS03112.ai

NOTE
Do not close the installation screen until the flash ROM write process is completed. If you inadvertently close the installation screen, return to Step 7 and perform the installation procedure again. The flash ROM write process takes about 8 minutes.

13. Check to see that 172.16.1.20 and CL0 have been set for IP
ADDRESS and CL NAME, respectively.

NOTE
If the FTP Server IP Address setting has been changed before the installation of the RU software, enter the new address.

[Click]

The installation screen appears on the CR-IR 391CL display.

FRCH7176.ai

While the flash ROM write process is being performed, the LED blinks.

FRCH7191.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-54

MC-55
16. Verify that the flash ROM write process is completed, and then press
the <Enter> key twice.
#1 [Check]

18. Check the version of the RU software, and close RU PC-TOOL.


#1 [Check] #2 RU TYPE CR-IRxxx: Model name of the RU to be connected is displayed. GOOD indication The text is displayed in black. NO GOOD indication The text is displayed in red or the version number is not displayed. RU NAME IP ADDRESS RU TYPE VERSION ru0 172.16.1.11 CR-IRxxx 1.1

#2 [Press 2 times] Enter key

FRCH7066.ai

17. Click [OK].


#3 [Click]

FRCH7068.ai CBS03116.ai

NOTE
If NO GOOD is indicated, go back to Step 1. and perform installation again.

19. Verify that the RUs LED is extinguished, and then turn OFF the RU.
REFERENCE
The message Under maintenance is displayed on the operation panel. However, turning OFF the RU power does not affect the RUs functionality.

20. Turn ON the power of the RU.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-55

MC-56
Restoring the RU-Config
Perform the procedure set forth below to restore the RU configuration file.

4.

From LIST OF EXISTING RU, select the RU whose data is to be restored.


Con iguration(C)

CAUTION
When restoring the following items, never turn OFF the RU since access to the RUs flash ROM is made in the restoring process. If you turn OFF the RU, the program on memory will be destroyed, making it impossible for the RU to restart. SCN ALL DATA SCN LIGHT COLLECTING DATA SCN OPTICAL DATA

EACH RU SETTING CONNECTION TEST RU NAME RU IP ADDR

F EXISTING RU

BACKUP

RESTORE

[Select] RU NAME IP ADDRESS RU TYPE ru7 172.16.1.110 CR-IRxxx

VERSION V1.0

ALL RUs SETTING

RU TYPE CR-IRxxx: Model name of the RU to be connected is displayed.

FRCH316A01.EPS

1. 2. 3.

5.
Have on hand the FD on which the RU-Config was backed up. Insert this FD into the FD drive. From the menu, select All programs Accessories Run.

From the RESTORE pull-down menu, select an item to be restored.


Con iguration(C)

EACH RU SETTING CONNECTION TEST RU NAME RU IP ADDR

L ST OF EXISTING RU

[Select]
RE

BACKUP

The Run window opens.

ALL RUs SETTING

CONFIGURATION HISTORY LOG SCN ALL DATA SCN LIGHT COLLECTING DATA SCN OPTICAL DATA
FRCH316A07.EPS

Enter C:\Program Files\FujiFilm\FCR\TOOL\RuPcTool\RuPCTool.exe and click [OK].


The RU PC-TOOL main menu opens.
Configuration(C)

6.

Click [EXECUTE].
Con iguration( )

RU PC-TOOL Ver.3.0
Operation(O)

EACH RU SETTING CONNECTION TEST RU NAME RU IP ADDR

L ST OF EXISTING RU

[Click]

EACH RU SETTING CONNECTION TEST ru0 RU NAME RU IP ADDR 172 MUTL PING 16 MON 1 10 FTP

BACKUP

RESTORE

LIST OF EXISTING RU RU NAME IP ADDRESS RU TYPE VERSION ru0 172.16.1.10 CR-IRxxx V1.0

NEW DELETE

ALL RUs SETTING

FRCH316A08.EPS

INSTALL BACKUP ERROR LOG

VERSION UP

EDIT HISTORY RESTORE

EDIT CONFIGURATION EDIT CL NAME

EXECUTE I/O TRACE EXPERT ALL RUs SETTING UNINSTALL VERSION UP ERROR DB

EXECUTE

FRCH4404.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-56

MC-57
7.
Select the location of the data to be restored.

9.

Reconfirm the location of the data to be restored, and then click [OK].
#2 [Click]

NOTE
To restore data from an FD, insert the FD, which stores the data to be restored, into the CR-IR 391CL before selecting a data location. If no FD is set in its position, you cannot select the FD drive (a:\).
#1 [Click] #1 [Check]

CBS03120.ai

10. When a message appears to indicate the completion of restore, click


[OK].

NOTE
If the data has been restored from an FD, be sure to click the [OK] button and then remove the FD.
#2 [Select]

CBS03121.ai

The system returns to the main menu of RU PC-TOOL.


CBS03118.ai

11. Click

in the upper-right corner of the window.

8.

Verify that the selected location is displayed, and then click [OK].
#1 [Verify] The selected location is displayed. #2 [Click]

The system returns to the desktop window.

CBS03119.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-57

MC-58 1.6 Installing the SQL Server


This section shows the procedures used to install the SQL Server. The SQL Sever is a database for managing images and patient information that are handled by the CR-IR 391CL system. Thus, the CR-IR 391CL, without the SQL Server installed, does not function.

3.

Click

The CR-IR 391CL applications setup window opens.

1. 2.

Insert the CR-IR 391CL application CD into the DVD drive. Select Computer from the DVD RW drive (D:).
The installation launcher starts

menu and double-click

(Vx.x represents a version number.)

CBS03123.ai

(Vx.x represents a version number.)

CBS03122.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-58

MC-59
NOTE
If the Install .NET Framework button is active, make the following settings. I. Click
The following window opens.

4.

Click
A window for language selection opens.

CBS03149.ai

CBS03124.ai

II. Click
The following window opens.

5.

Select a desired language, and click [Next].


The command prompt window opens, and installation of the SQL Server starts. Installation processing completes.

CBS03150.ai

III. Click the [Next]. The system returns to the installation launcher window.

CBS03125.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-59

MC-60
6.
Press the <Enter> key.

NOTE
If the window prompting you to restart opens, click [Yes] to restart the system.

CBS03130.ai

The command prompt window closes, and the system returns to the installation launcher.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-60

MC-61 1.7 Installing the CR-IR 391CL Software


This section shows the installation procedures of the CR-IR 391CL software, menu and parameter files, and the standard kit CD.

1.7.1 Installing the CR-IR 391CL

1.

Click

INSTRUCTIONS
If there is a backup of the config data, be sure to perform installation of the application of the same version as the one for which the backup was made. To install the application of a version newer than the one in which backup was performed, the following procedure becomes necessary. Installation of the old-version application in which the backup was taken Restoration of the config data Update of the application For details on the procedure, see Appendix 2: CR-IR 391CL Software Version Upgrade.

NOTE
Make sure to perform installation processing set forth herein with the PC properly connected to a network, otherwise intended processing will result in a failure.

(Vx.x represents a version number.)

CBS03126.ai

The installer starts, and the Welcome to the InstallShield Wizard for FCR Application window opens.

CBS03127.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-61

MC-62
2.
Click [Next].
The Ready to Install the Program window opens.

4.

Click [Finish].
The following window opens.

CBS03130.ai

CBS03128.ai

5.

Click [Yes].
The PC restarts.

3.

Click [Install].
In about 2 minutes, a command prompt window opens. The following window indicating completion of the installation opens.

CBS03129.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-62

MC-63
1.7.2 Installing a Settings File

4.

Select a language to install configuration files, and click [Next].


The window for selecting the type of monitor opens.

1.

On the installation launcher window, click CR-IR 391CL Application Setup.


The CR-IR 391CL applications setup window open.

2.

Click
The Select a type of facility window opens.

CBS03133.ai

5.

Select Color, and click [Next].


The confirmation window opens.

CBS03154.ai

3.

Select Hospital/Medical Clinic, and click [Next].


The Select language to install Configuration files window opens.

CBS03134.ai

6.

Click [Yes].
Installation of the configuration file starts. When the installation completes, the CR-IR 391CL applications setup window opens.

CBS03132.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-63

MC-64
1.7.3 Installing Menu and Parameter Files

3.

Select a desired language, and click [Next].


A window opens prompting for confirmation of the parameter file installation.

1.

In the installation launcher window, click


The Select a type of facility window opens.

CBS03136.ai

4.
CBS03135.ai

Select ON (Software Options required) and click [Next].


The configuration window opens.

2.

Select Hospital/Medical Clinic, and click [Next].


The window for selecting the study menu language opens.

CBS03137.ai

5.
CBS03135.ai

Click [Yes].
Installation of the parameter file starts. When the installation completes, the CR-IR 391CL applications setup window opens.

6. 7.
020-221-02E 01.08.2010 FM5563

On the installation launcher window, click [Finish]. Remove the CD from the DVD drive.

CR-IR 391CL Service Manual

MC-64

MC-65
1.7.4 Installing the Standard Kit CD

4.

When Press any key. appears, press the <Enter> key.

1. 2.

Insert the standard kit CD into the DVD drive. Select Computer from the menu and double-click DVD drive (D:).
MC000156.EPS

The application automatically starts, and a command prompt opens.

REFERENCE
Open the DVD drive and double-click the Setup Windows Batch File when the application doesnt start automatically. Then, a command prompt opens.

5.

When Press any key to continue... opens in the command prompt window, press the <Enter> key.

MC000314.EPS

CBS03155.ai

6. 7.

Remove the CD from the DVD drive. Install the AP key.


See 2. AP Key Installation in Appendix 3: Option Key / AP Key Installation

3.

When Press any key to continue... appears, press the <Enter> key.

8.

Restart the PC.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-65

MC-66 1.8 Settings by the Simplified Setup Wizard


For settings performed by the Simplified setup wizard, see 4.4 Setup by the Simplified Setup Wizard under IN: Installation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-66

MC-67 1.9 IIS Network Virus Protection


To provide network virus protection, complete the following setup procedures for IIS. Disabling unnecessary accounts that can access the FTP service

6.

Choose the Security Accounts tab and then uncheck Allow Anonymous Connections ( ).

Disabling unnecessary accounts that can access the FTP service

1. 2. 3. 4.

From the

menu, choose [Control Panel].

The Control Panel window opens.

Double-click [Administrative Tools].


The Administrative Tools window opens.

Double-click [Internet Information Services (IIS) 6.0 Manager].


The Internet Information Services window opens.
CBS03152.ai

Double-click the host name in the left-hand section and then select FTP Sites, and click Default FTP Site in the right-hand section.

7.

When the confirmation dialog box opens, click [Yes].

CBS03151.ai CBS03153.ai

5.

From the Action menu, choose Properties.


The Default FTP Site Properties window opens.

8. 9.

Click [OK].
The system returns then to the Internet Information Services window.

Close the Internet Information Services window and Control Panel window.

10. When the confirmation dialog box opens, click [Yes].


After the PC restarts, the CR-IR 391CL starts automatically.
020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-67

MC-68 1.10 Making Checks Using the Service Utility


1.10.1 Running the Simplified Setup Wizard
After completion of reinstallation, run the Simplified setup wizard (contained in the Service Utility) in order to make sure that all necessary settings have been made.
For more information, see 5. Simplified Setup Wizard under MU: Maintenance Utility. For information on how to open the Service Utility, see 2. Starting, Loggingin to, and Exiting the Service Utility under MU: Maintenance Utility.

1.10.4 Installing Adobe Reader and Copying the Reference Guide

1. 2.

Insert the Reference Guide CD into the DVD drive. Double-click D:/Adobe Reader/English/AdbeRdr910_en_US_Std.exe, and install Adobe Reader.

NOTE
When installing, remain the setting values as default.
After the installation, the Adobe Reader 9 icon appears on the desktop.

1.10.2 Checking for Connection with Other Equipment


Check for connection with equipment that is setup under Connected equipment in Service settings. Connection checks are divided into checking connection to the host equipment and that to the DICOM equipment.
For more information, see 7.3 Connection Check under MU: Maintenance Utility.

3. 4. 5.

Double-click the Adobe Reader 9 icon.


The Adobe Reader - License Agreement window opens.

Click [Accept].
The Adobe Reader window opens.

1.10.3 Checking the Date Format


Check to see that the order of entering year/month/day is consistent with each other for the CR-IR 391CL and the OS.

From the menu bar, select Edit - Preferences and make the following settings.
I. II. III. IV. Remove the checkmark from General - Check for updates. Remove the checkmark from Internet - Allow speculative downloading in the background. Remove the checkmark from Internet - Display PDF in browser Remove the checkmark from Trust Manager - Load trusted root certificates from an Adobe server (no personal information is sent).

CAUTION
Any inconsistency between the date format order used in the CR-IR 391CL system and that used in the OS may cause necessary information, such as study date, to be displayed incorrectly. Setting of the date format used in the CR-IR 391CL system
For details, see 5.3 System Settings under MU: Maintenance Utility.

6. 7. 8. 9.

Click [OK]. From the menu bar, select File - Exit.


The system returns to the desktop screen.

Setting of the date format used in the OS


For details, see 4. Regional and Language Options Settings under MU: Maintenance Utility.

From the Reference Guide CD, copy the necessary guides onto the desktop. Remove the Reference Guide CD from the DVD drive.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-68

MC-69
1.10.5 Setting the User Account Control (Activate)
Turn on the User Account Control.

1. 2. 3. 4.

Select [Control Panel] from the


The Control Panel window opens.

menu.

Double-click User Accounts.


The User Accounts window opens.

Select Turn User Account Control on or off.


The Turn User Account Control on or off window opens.

Place a checkmark in Use User Account Control (UAC) to help protect your computer.

MU060214.ai

The following window opens.

MU060212.ai

5.

Click [Restart Now].


The PC restarts. After a while, the CR-IR 391CL starts up.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-69

MC-70 1.11 Restoring the CR-IR 391CL Config Data


Of the information that has been backed up, restore the menu setting information, setup information, user information, and explanatory information here in this section. Patient information is to be restored later.

2.

Select Back Utility and click [OK].

NOTE
This section shows the procedures of restoring setting information on the user environment which is required for test startup. In test startup, a dummy patient will be registered for checking for proper operation. Such dummy data must be deleted by database initialization after the operation check. Since restoration of patient information needs to be performed after such a checkup procedure, it is not performed at this stage.

CBS03138.ai

The confirmation window opens.

CAUTION
When restoring the config data, be sure to perform it for the application of the same version as the one in which the backup was made. If versions do not match, it may become necessary to perform installation of the application again.

1.

In the CR-IR 391CL login window, click [Finish].


The Select Server Application Behavior window opens.

CBS03139.ai

3.

Click [OK].
After the system exits, the User authentication window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-70

MC-71
4.
Type in the username medicalservice and the password fieldengineer.

6.

Click [Restore].
The Select folder window opens.

NOTES
The username and the password both must be all in lowercase letters. In addition, they should contain no space characters. Since the username medicalservice is not registered in the pull-down menu, be sure to enter it from the keyboard.

CBS03142.ai

7.

Click [Browse].
The Browse For Folder window opens.

CBS03140.ai

5.

Click [OK].
The Main Menu window opens.

CBS03143.ai

8.
CBS03141.ai

Specify the destination folder to which the information is to be restored, and click [OK].
The path of the specified folder is entered and shown in the Select folder field.

REFERENCE
The destination folder for information restoration can also be specified by directly typing its path into the Select folder field.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-71

MC-72
9.
Click [OK].
The Restore window opens.

NOTE
In the case of restoring IP use count data: I. Checkmark IP counter information ( ). II. Click [Start]. The [64402] IP use count data will be restored. window opens.

10. In the Select Information to be restored section, select Menu

Setting Information, System configuration Information, User Information, and Explanatory Information.

CBS03146.ai

III. Click [OK]. A restoration completed window opens.

12. Click [OK].


The system returns to the Select folder window.
CBS03144.ai

13. Click [Cancel].


The system returns to the Main Menu window.

11. Click [Start].


The following restoration completed window opens.

14. Click [Finish].


The system returns to the desktop.

CBS03145.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-72

MC-73 1.12 Operation Check and Initialization after Installation


Checking for proper startup operation

3.

Enter the password fieldengineer (in lower-case single-byte characters only) and click .

1.

Restart the CR-IR 391CL to make sure that the following applications automatically start.
Server application Client application Visually check the screen to determine whether the following Select a User window successfully opens, meaning that the startup operation has been performed properly.

2.

On the User Selection window, click the top, bottom, left, and then right edge portions of the window in order.

CBS03157.ai

The indicator window opens.

4. 5.

Check to see that the indicator icon is not blinking. Click the indicator icon (Event log). On the window that opens,

make sure that there is no error logged.


For more information on the indicator icon, see the CR-IR 391CL Operation Manual.
CBS03156.ai

6.

Check to see that the User Utility can be started.


For information on how to open the User Utility, see Appendix 2: User Utility under MU: Maintenance Utility.

The Password input window for service engineers shows up.

NOTES
The top, bottom, left, and right edge portion clicks should be done slowly. Too fast clicking may render the detection of position information impossible. In the event of a login failure, click [Finish] and close the User Selection window once. Click [FCR PRIMA Console] on the desktop to reopen the User Selection window and go over the above-mentioned operation again.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-73

MC-74
Making checks of basic operations
Make checks of basic operations from study reservation to writing to DVD to verify proper operation.
For information, refer to 5.3 Checking Every Step from the Inputting of Images to the Saving of Images onto DVD under IN: Installation.

1.13 Restoring the CR-IR 391CL Configuration Data (patient information)


Of the data that was backed up beforehand, restore the patient information.

If there is any option(s) installed, run operation checks on each option on a one-byone basis.
For details, see 7. Links to Individual Option Items under IN: Installation.

1.

Right-click the CR-IR 391CL server icon on the task tray in the bottomright corner of the desktop screen.

Database initialization
Initialize the database.
For information, refer to 7.1 Database Utility under MU: Maintenance Utility.

IN000402.ai

Its right-click menu opens.

2.

Click [Backup Utility].


The confirmation window opens.

Executing CreateNewHistoryDB.bat

1. 2. 3.

Click [Computer] from the


The Computer window opens.

menu.

Open the C:\ProgramData\FujiFilm\Hobbit\Temp\HistoryDB\SQL\ CreateDatabase folder. In the CreateDatabase window, double-click [CreateNewHistoryDB. bat].
The command prompt window opens, and Initializing History Database is in progress appears.
CBS03139.ai

3.

Click [OK].
After the system exits, the User authentication window opens.

4. 5. 6.

Check to see that error.log is not in the CreateDatabase window. Click at the upper left corner of the window.

The system returns to the Computer window.

Close the Computer window.


The system returns to the desktop screen.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-74

MC-75
4.
Type in the username medicalservice and the password fieldengineer from the keyboard.

6.

Click [Restore].
The Select folder window opens.

NOTES
The username and the password both must be all in lowercase letters. In addition, they should contain no space characters. Since the username medicalservice is not registered in the pull-down menu, be sure to enter it from the keyboard.

CBS03142.ai

7.

Click [Browse].
The Browse For Folder window opens.

CBS03140.ai

5.

Click [OK].
The Main Menu window opens.

CBS03143.ai

8.
CBS03141.ai

Specify the destination folder to which information is to be restored, and click [OK].
The path of the specified folder is displayed in the Select folder field.

REFERENCE
The destination folder for information restoration can also be specified by directly typing its path into the Select folder field.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-75

MC-76
9.
Click [OK].
The Restore window opens.

12. Click [OK].


The system returns to the Select folder window.

10. Select Patient Information alone and leave other items unselected in
the Select Information to be restored section.

13. Click [Cancel].


The system returns to the Main Menu window.

14. Click [Finish].


The system returns to the desktop.

CBS03148.ai

11. Click [Start].


The restoration completed window opens.

CBS03145.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-76

MC-77 1.14 Reconstructing the Image Database


This section shows the reconstruction procedures of the image database using the storage disk. What is reconstructed here is the index information as the image database, and images themselves are not restored. In order to restore images themselves, it is necessary to retrieve images for each study one by one after completion of the database reconstruction.

3.

From the [Tool] menu in the upper-left of the Study List window, select Client utilities.

REFERENCE
For V1.1(B) or later, start up the Client Utilities by selecting Client Utilities from the Utilities at the bottom of the Main window.

NOTE
When performing reconstruction from storage disks, be sure to perform reconstruction beginning from the oldest dated disk. In the CR-IR 391CL system, because of its re-verification feature, a study may possibly be stored spanning more than one disk. By restoring disks in ascending chronological order, older study information stored before re-verification is overwritten by newer information.

IN000633.ai

The Client Utilities window opens.

1. 2.

Start the CR-IR 391CL. Insert the storage disk for reconstruction into the internal DVD drive (drive for storage).

MC000162.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-77

MC-78
4.
Click [Disk Operation].
The Disk Operation window opens.

6.

Select Studies are updated (studies included in the database are deleted and disk studies are registered). and click [Start].
The Database Restoration (2) window opens.

MC000165.EPS

When processing completes, the system returns to the Disk Operation window automatically.

7.
MC000163.EPS

Click [Close].
The system returns to the Client Utilities window.

5.

Click [Database Restoration].


The Database Restoration (1) window opens.

8.

Click [Close].
The Client Utilities windows closes.

NOTE
When image database restoration has been done from a storage disk, that disk is set to Write disabled. Ask the institutions administrator if it is necessary to write additional data to the storage disk. If yes, change the disks setting from Write disabled to Write enabled.

MC000164.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-78

MC-79
9.
Click [Update] from List Operations in the Study List window.

Verifying image restoration


This section shows the procedures of test-retrieving images of the studies that have been restored by image database reconstruction.

REFERENCE
For V1.1(B) or later, start up the Study Utility by selecting Study Utilities from the Utilities at the bottom of the Main window.

NOTE
Here in this section, only one image is to be retrieved and viewed for verification and not all images are to be restored.

1.
IN000632.ai

In the Study List window, select one study and click Load Disk Images.
The Retrieve Images from Disks window opens.

The restored study data now opens on the list.

MC000210.EPS

2.

With the option in the dialog as it is (For System being checked), click the [Retrieve] button.
The Image retrieve window opens, and image retrieval starts.

MC000209.EPS

10. When there are two or more storage disks, repeat Steps 1. through 5
for the number of disks.

MC000211.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-79

MC-80
When the image retrieval finishes, Retrieve of the study completed. window opens.

5.

With the study being selected appropriately, click [Image Viewer].


The Image Viewer window opens.

MC000212.EPS

3. 4.

Click [OK]. On the Study List window, make sure that a thumbnail image is appearing.

MC000214.EPS

6.

Make sure that the image is properly displayed, and click Finish in the upper-left corner to close the window.

MC000213.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-80

MC-81

2. Service Parts Replacement (for DELL PCs)


This section describes ways of replacing parts used in the CR-IR 391CL.
Target work
Preparation for parts replacement Hard disk DVD drive FDD drive CPU Memory Motherboard Power supply unit 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 Hard Disk DVD Drive FD Drive CPU Memory Motherboard Power Supply Unit

2.1 Preparation for Parts Replacement


Dismounting procedure

1. 2.

Reference
Preparation for Parts Replacement

Shut down Windows Vista and then turn OFF the power to the CR-IR 391CL-PC. Disconnect the CR-IR 391CL-PC power cord from the power supply.

NOTE
Be sure to hold the plug to disconnect the power cord. Disconnecting the power cord holding the cable may break it.

3. 4. 5. 6.

Disconnect all cables from the rear of the CR-IR 391CL-PC. Place the PC in vertical orientation, and secure 1 to 2 meters of clearance to the front, rear, sides and above it. Pull its handle portion to open the cover. Lay down the PC flat.

REFERENCE
These parts replacement procedures written in this section, 2. Service Parts Replacement (for DELL PCs), are described on the DELLs website as well.

Mounting procedure
Reverse the dismounting procedure to mount a part.

NOTES
After finishing the necessary work, check to see that the CR-IR 391CL starts up normally. Perform an operation check on the replaced part(s) by using Dell Diagnostics. For detailed information, see 4.8 Error Analysis Tool (Dell Diagnostics) under MT: Machine Troubleshooting.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-81

MC-82 2.2 Hard Disk


CAUTIONS
Before replacing the hard disk, be sure to make a backup copy of the database. When performing data backup, be sure to determine the version of the application and take a note of it. After mounting a new hard disk and restoring the PC, be sure to perform reinstallation of the OS and the application.

2.3 DVD Drive


Dismounting procedure

1. 2.

Place the PCs enclosure in vertical orientation. Pull its handle portion to open the cover.

Backing up the database


Using the Backup Utility, make a backup copy of image data and config data.
For detailed information on how to perform backup, see Appendix 1: Backup Utility under MU: Maintenance Utility.

3. 4.

Lay down the PC flat. Pull the power connector (indicated by the red circle in the figure) from the DVD drive.

Dismounting procedure

1. 2. 3. 4.

Make preparations for parts replacement.


For the procedure for making parts-replacement preparations, see 2.1 Preparation for Parts Replacement.

Disconnect signal cables and power cable from the hard disk. While pushing the right and left drive rails, lift the hard disk assembly to remove it. Remove the drive rails attached to the left and right sides of the hard disk assembly.

Mounting procedure
Reverse the dismounting procedure to mount a part. After mounting a new hard disk drive, perform installation of the OS and the application.
For detailed information on the installation procedure, see 1. Reinstalling the OS and the Application.
MC000202.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-82

MC-83
5.
By holding the black connector, disconnect the S-ATA cable (indicated by the blue circle in the figure) from the DVD drive.

Mounting procedure

1.

Fix three screws on the side of the DVD drive.

NOTE
Do not tighten the screws completely. Secure the screws in a manner where their unthreaded portion comes just in contact with the drives side surface.

2. 3.

Make sure that the FD drive has not come off. Put the replacing DVD drive into place.

MC000202.EPS

6.

Do the following:
While pulling the trigger (indicated by the red circle in the figure) toward the front, II. Install the DVD drive by sliding it sideways. I.

NOTE
The trigger is used also for mounting/dismounting the FD drive located underneath the DVD drive. Therefore, be aware that tilting or moving the PC main unit during the work may cause the trigger to be disengaged.

While pulling the trigger (indicated by the red circle in the figure) toward the front, II. Remove the DVD drive by sliding it sideways.

I.

4. 5. 6. 7. 8.

Check to see that the trigger is returned into its original position. Attach the power connector that was removed in Step 4 under Dismounting procedure to the DVD drive. Attach the IDE connector that was removed in Step 5 under Dismounting procedure to the DVD drive. Attach the cover that was removed in Step 2 under Dismounting procedure into place. Visually check to see from the outside that the DVD drive and the FD drive are properly mounted. If it is found to have come off, open the cover of the PC main unit and take the DVD drive out, and then perform Steps 3 and thereafter.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-83

MC-84 2.4 FD Drive


Dismounting procedure

2.5 CPU
CAUTION
Whenever dismounting/remounting the CPU, be sure to wear a wrist strap to discharge the buildup of static electricity that is held by the human body, otherwise, the CPU may be damaged due to static electricity discharged from the human body.

1. 2. 3. 4.

Make preparations for parts replacement.


For the procedure for making parts-replacement preparations, see 2.1 Preparation for Parts Replacement.

Disconnect the signal and power cables from the FD drive, and remove the signal cables from the DVD drive. While pushing the right and left drive rails, lift the FD drive assembly to remove it. Remove the FD drive rails attached to the left and right sides of the FD drive assembly.

NOTE
Carefully handle the CPU as it can be damaged easily.

Dismounting procedure

Mounting procedure
NOTES
Check to see that the switch on a new FD drive is set to the CABLE SELECT position before mounting the FD drive.
CABLE SELECT SLAVE MASTER Rear of the FD drive

1. 2.

Loosen the screws on both sides of the heat sink cover (two pieces). Pull up the front end of the frame upward and remove it.

MC000036.EPS

Connect cables correctly, as illustrated below, paying attention to the FD drive interface cable polarity.
To motherboard To FD drive

MC000218.EPS

NOTE
The heat sink may be still hot. Allow enough time for it to cool down before you touch it.

Cable wires are twisted.

MC000035.EPS

3. 4.

Wipe off the silicone grease on the mating surfaces between the heat sink and the CPU with dry cloth. Slide the CPU socket lever to open the CPU cover.

Reverse the dismounting procedure to mount a part.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-84

MC-85
5.
While pulling the CPU socket lever toward the rear, remove the CPU.

2.6 Memory
CAUTION
Whenever dismounting/remounting memory, be sure to wear a wrist strap to discharge the buildup of static electricity that is held by the human body, otherwise, the CPU may be damaged due to static electricity discharged from the human body.

NOTE
After removing the CPU, be careful not to touch or drop something on the pins of the CPU socket. Any possible damage to the CPU socket pins may cause the PC unable to operate properly.

Dismounting procedure
NOTE
Before mounting the CPU, apply clean silicone grease on the mating surfaces between the CPU and the heat sink. Reverse the dismounting procedure to mount a part.

Dismounting procedure

1. 2.

Make preparations for parts replacement.


For the procedure for making parts-replacement preparations, see 2.1 Preparation for Parts Replacement.

Open levers on both the right-and-left sides of the memory socket to remove the memory.

Lever

MC000037.EPS

Mounting procedure

1.

Set the memory in an upright position and push it in the socket.


When the memory is pushed in the socket, levers located on both the rightand-left sides will close automatically.

NOTE
Pay due attention to the memory mounting direction. A notch is provided on the terminal side of the memory to prevent it from being pushed in the socket mistakenly.

2.
020-221-02E 01.08.2010 FM5563

Restore the PC.


To restore the PC, follow the steps described in 2.1 Preparation for Parts Replacement in reverse.

CR-IR 391CL Service Manual

MC-85

MC-86 2.7 Motherboard


CAUTION
Whenever dismounting/remounting a motherboard, be sure to wear a wrist strap to discharge the buildup of static electricity that is held by the human body, otherwise, the motherboard may be damaged due to static electricity discharged from the human body.

3.

Disconnect all connectors from the motherboard.


Signal cables for the hard disk Signal cables for the FD drive Signal cables for the DVD drive. Power cable (for main power supply/CPU power supply) USB signal cables

4.

Remove screws and dismount the motherboard.

NOTES
Users equipment-specific information or setup information is stored in the memory (CMOS) on the motherboard. Prior to replacing a motherboard, be sure to jot down such stored data properly. When the motherboard has been replaced, it is necessary to reinstall the option key, the application key, and the standard options (to be installed from the standard kit). On the CR-IR 391CL system, optional features do not function after motherboard replacement. For information on how to reinstall the standard options, see 4.10 Tasks to be Performed at Motherboard Replacement under MT: Machine Troubleshooting.

Mounting procedure
Reverse the dismounting procedure to mount a part.

Setting the BIOS


For details of the necessary procedure, see Appendix 8: Setting the BIOS.

Dismounting procedure

1.

Make preparations for parts replacement.


For the procedure for making parts-replacement preparations, see 2.1 Preparation for Parts Replacement.

2.

Remove the following components that are mounted on the motherboard.


Memory CPU Card cage For the CPU replacement procedure, see 2.5 CPU. For the memory replacement procedure, see 2.6 Memory.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-86

MC-87 2.8 Power Supply Unit


Dismounting procedure

1.

Make preparations for parts replacement.


For the procedure for making parts-replacement preparations, see 2.1 Preparation for Parts Replacement.

2.

Disconnect power cables from the motherboard and various drives.

NOTE
When disconnecting the power cables from the motherboard and drives, take a note of their wiring routes you can see under the tab in the cabinet frame. When reconnecting these cables, thread them appropriately being careful not to get them pinched or bent sharply.

3. 4. 5. 6.

Remove the card cage. Press down the green handle located on the power supply unit.
The fastening of the power supply section is disengaged.

Slide the power supply unit 2 to 3 cm toward the front of the PC. Raise the power supply unit and remove it.

Mounting procedure
Reverse the dismounting procedure to mount a part.

CAUTION
For a PC provided with the source voltage changeover switch (between 115 and 230 VAC), set the PC source voltage according to the voltage supplied to the institution concerned and then connect the power cable to the power source.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-87

MC-88

3. Updating the Software


3.1 Updating the CR-IR 391CL
For detailed information on how to perform a version update of the CR-IR 391CL, see Appendix 2: CR-IR 391CL Software Version Upgrade.

3.2 Updating the RU Software


For updating the RU PC-TOOL, see IN 8 of CR-IR 391RU Service Manual. For updating the RUsoftware, see MU: 1.12 VERSION UP of CR-IR 391RU Service Manual.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-88

MC-89
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-89

MC-90
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MC-90

Appx MC 1-1

Appendix 1 Setup for Security Enhancement


To provide CR-IR 391CL security enhancement, complete the following three setup procedures. Replacing the default password with a new password Changing the setup so that the computer prompts for password input at logon Defining the minimum character count for the password

n Replacing the default password with a new password

1. 2. 3.

Simultaneously press the [Ctrl], [Alt], and [Delete] keys.


The Windows Security window opens.

Click the [Change a password] button.


The Change Password window opens.

NOTES
Settings performed for password change and prompt for password input at login will not start up the CR-IR 391CL automatically. To have it start up automatically, it is necessary to input the user name and the password on the Windows initial screen.

From the Change Password window, perform the following setup steps.
I. Enter the currently used password (system by default). II. Enter a new password consisting of no more than seven characters. III. Enter the new password again for confirmation.

4. 5.

Click

The Your password has been changed. is displayed.

Click [OK].
The system returns to the desktop screen.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 1-1

Appx MC 1-2
Changing the setup so that the computer prompts for password input at logon n Defining the minimum character count for the password

1.

1.

Open Control Panel. Double-click and then .

From the

menu, enter control userpasswords2 in the search

area and press the <Enter> key.

The Local Security Policy window opens.

CBS03149.ai

The User Accounts window opens.

2.

Place a checkmark in User must enter a user name and password to use this computer..

CBS03151.ai

2.
CBS03150.ai

Click the

mark for

and then click

The right-hand pane shows the password policy settings.

The User Accounts window opens.

3.

Click [OK].
The system returns to the desktop screen.

3.

Double-click

The Local Security Policy Setting window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 1-2

Appx MC 1-3
4.
Set the number of password characters to 7.

CBS03152.ai

5. 6. 7.

Click [OK] .
You are then returned to the Local Security Policy window.

Close the Local Security Settings window. Close the Administrative Tools window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 1-3

Appx MC 1-4
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 1-4

Appx MC 2-1

Appendix 2 CR-IR 391CL Software Version Upgrade


Uninstalling the CR-IR 391CL system program
NOTE
In case of a dual-monitor configuration, back up the setting file (C:\Program Files\ FujiFilm\Hobbit\System\FDDSettingInfo.ini) for the free drawing function before uninstalling the client application.

9.

Click the [x] mark in the Add or Remove Programs window to close it.
The system returns to the installation launcher window.

10. Click the [Finish] button and remove the CD from the DVD drive. 11. Restart the PC.

1. 2. 3. 4.

Start up the PC.


The CR-IR 391CL starts up automatically.

Shut down the CR-IR 391CL server. Insert the CR-IR 391CL application CD into the DVD drive. Select Computer from the
The installation launcher starts up.

menu and

double-click DVD RW drive (D:).

5. 6.

Click
The Program and Features window opens.

Select FCR Application and click the [Uninstall] button.


The Do you wish to delete FCR Application from your computer? window opens.

7. 8.

Click [Yes].
The Windows Installer goes up and running to start uninstallation processing.

Wait until FCR Application (in the window where progress bar is present) disappears automatically.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 2-1

Appx MC 2-2
Installing the CR-IR 391CL system program
NOTE
Because the CR-IR 391CL application installer changes the system files, the PC may be restarted without displaying any confirmation message, depending on the Windows Installer version. In such cases, log in the system anew and then perform processing continuously.

10. Restart the PC.


REFERENCE
Settings before version upgrade are taken over as they are after version upgrade processing is performed.

1. 2. 3.

Log in the system by entering fujicr as the username and system as the password. Insert the CR-IR 391CL application CD into the DVD drive. Select Computer from the
The installation launcher starts up.

menu and

double-click DVD RW drive (D:).

4.

Click (Vx.x represents a software version number).

5. 6. 7. 8. 9.

Click (Vx.x represents a software version number). Click [Next].

The installer starts up and the Welcome to the InstallShield Wizard for the FCR Application window opens.

Click [Install].
A window opens to indicate progress of installation processing, which takes about 2 minutes to finish.

Click [Finish].
The system returns to the installation launcher window.

Remove the CD from the DVD drive.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MC 2-2

Appx MC 2-3
Confirmation of version upgrade

1. 2. 3.

The software version displayed in the lower-right of the startup window should be correct. The CR-IR 391CL system should start up unfailingly. There should be no errors in the event log (Control Panel Administrative Tools Event Viewer Windows Logs Application) and the source name MsInstaller.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MC 2-3

Appx MC 2-4
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 2-4

Appx MC 3-1

Appendix 3 Option Key / AP Key Installation 1. Option Key Installation


Install the option keys as follows.

The installation procedure is described below. The same installation procedure applies to all the option keys.

NOTE
When installing an option key or the AP key, network to the CR-IR 391CL system must have been established properly. Be sure to check the network connection and then install an option key or the application key.

NOTES
Each option key is supplied on one dedicated CD-ROM for each product. After option key installation, be sure to install the AP key. The reason is that installing the option keys disables the AP key that has been enabled.
CD label
MFP Key Software DICOM Print Key Software Free Layout Print Key Software DICOM Standard CR Storage Key Software DICOM ID MWM Key Software

1. 2.

Insert an option key CD into the DVD drive. Select Computer from the menu and

double-click DVD RW drive (D:).


A window opens to indicate the completion of installation.
The indication varies with the option key for installation.

Description
MFP image processing function DICOM print function Free layout print function DICOM CR Storage output function DICOM MWM patient information function Appendix 1 in Appx IN: Installation Appendix Appendix 3 in Appx IN: Installation Appendix

IN000443.ai

3.

Click [Continue].
A window opens to indicate the completion of installation.
The indication varies with the option key for installation.

IN000444.ai

4. 5. 6.

Click [OK].
The system returns to the desktop screen.

Remove the CD from the DVD drive. To install another option key, change the CD and repeat Steps 2 through 5 as appropriate.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MC 3-1

Appx MC 3-2

2. AP Key Installation
Install the AP key as follows.

5. 6.

Remove the CD from the DVD drive. Restart the PC.

NOTE
Install the AP key after all the option keys have been installed appropriately. The reason is that installing the option keys disables the AP key that has been enabled, requiring it to be reinstalled anew. Install the AP key as follows:

1. 2.

Insert the AP key CD into the DVD drive. Select Computer from the menu and

double-click DVD RW drive (D:).


The installation start window opens.

CBS03155.ai

3.

Click [Continue].
A window opens to indicate the completion of installation.

CBS03156.ai

4.

Click [OK].
The system returns to the desktop screen.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 3-2

Appx MC 3-3
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 3-3

Appx MC 3-4
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 3-4

Appx MC 4-1

Appendix 4 Setting the RU-Config


NOTES
Verify that Explorer or other application is not running. If any applications are running, exit them. Start the setting work with the CR-IR 391CL shut down accordingly.

II. Click [OK]. The Select Server Application Behavior window opens.

Preparatory work: Shutting down the CR-IR 391CL


If and when the CR-IR 391CL is up and running, exit it using the following procedure:
CBS03158.ai

III. Select Exit and click [OK].

1.

If the CR-IR 391CL client is up and running, exit it.

2.

If the CR-IR 391CL server is up and running, exit it.


I. Right-click the icon representing the CR-IR 391CL server in the task tray at the bottom right of the desktop screen.

When in the login window: I. Click [Finish] in the lower left corner of the login window.
The CR-IR 391CL client terminates and the desktop screen opens.

When in the Study List window: I. Click [Close] in the upper left corner of the Study List window.
The following confirmation dialog box opens.

IN000402.ai

The following right-click menu opens.

CBS03159.ai

CBS03157.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MC 4-1

Appx MC 4-2
II. Click [Shut Down]. The confirmation window opens.

Setting the RU-Config


For setting up RU-Config property, see MU:1.14 EDIT CONFIGURATION of CR-IR 391RU Service Manual.

CBS03160.ai

III. Click [OK]. The following window opens indicating that the termination is in progress. Upon completion of the termination process, The system returns to the desktop screen. IV. Make sure that there is no CR-IR 391CL server icon on the task tray.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 4-2

Appx MC 4-3
Checking the Connection

1.

Start up the Service Utility.


For the procedure to start up the RUs Service Utility, see 2. Starting, Logging-in to, and Exiting the Service Utility under MU: Maintenance Utility.

The Service Utility top window opens.

2. 3.

Click [Connection check].


The Connection Check window opens.

Click the down-arrow button beside [RU0] under Check connection to the host equipment and select the appropriate RU from the pull-down menu that appears.
Its host name appears. If there is no host name, an IP address appears instead.

4.

Click [Verify connection].


A command prompt window opens. If the following message is displayed four times on the command prompt window, the connection is in proper working order. Reply from 172.16.1.10: bytes=32 time<10ms TTL=128

REFERENCE
Values for time<10ms and TTL=128 in the message above vary depending on the network status. Connection remains normal even though such values vary.

5.

Click the command prompt windows command prompt.

button to terminate the

The system returns to the Connection Check window.

6. 7.

Click [Finish].
The system returns to the Service Utility top window.

Click [EXIT].
The system returns to the desktop screen.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 4-3

Appx MC 4-4
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 4-4

Appx MC 5-1

Appendix 5 Procedures for Changing the CR-IR 391CL, RU, and Printer IP Addresses
This appendix explains about the procedures for changing the CR-IR 391CL, RU, Printer IP addresses. The IP addresses need to be changed in the following case: When the CR-IR 391CL, RU, Printer IP addresses need to be changed for hospital network management purposes

1. Incorporating into the Network


In compliance with the hospital network specifications, connect the CR-IR 391CL and RU network cables to the hospitals network.

NOTE
If the IP address of the CR-IR 391CL has been changed, it becomes necessary to change the RU-Config accordingly. Conversely, if the IP address of the RU has been changed, it is necessary to make a setting change using the CR-IR 391CLs Service Utility. If a setting change is made on either one alone, it becomes impossible to establish a connection.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 5-1

Appx MC 5-2

2. Changing the Software Settings


2.1 Changing the CR-IR 391RU IP Address

2.1 Changing the CR-IR 391RU IP Address


1.
Change the RU IP Address setting.
For details, see MU 4.3 [1] of CR-IR 391RU Service manual.

2.2 Changing the Printer IP Address 2.3 Making a setting change using the CR-IR 391CLs Service Utility 2.4 Changing the CR-IR 391RU Setting

NOTE
After changing RU-IP Address, reflect the setting to FF-WakeOnLAN Utility. For detail, see Appendix 6: Setting up WakeOnLAN.

2.5 Changing the Service PC IP Address

2.2 Changing the Printer IP Address


For the procedure to make the setting, see the Service Manual of the DRYPIX 1000/2000/3000/4000/7000/PRIMA.
See IN: Installation in the Service Manual of the DRYPIX 1000/3000. See IN: Installation in the Service Manual of the DRYPIX 2000. See IN: Installation in the Service Manual of the DRYPIX 4000. See IN: Installation in the Service Manual of the DRYPIX 7000. See IN: Installation in the Service Manual of the DRYPIX PRIMA.

2.6 Changing the CR-IR 391CL IP Address

2.7 Restart the CR-IR 391CL , RU, and Printer

2.8 Verifying the connection after IP address changes

NOTE
After changing Printer-IP Address, reflect the setting to FF-WakeOnLAN Utility. For detail, see Appendix 6: Setting up WakeOnLAN.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 5-2

Appx MC 5-3 2.3 Making a setting change using the CR-IR 391CLs Service Utility
NOTE
In the case of changing the CR-IR 391CLs own IP address, making an IP address change via the control panel of Windows alone does not affect the setting on the connection destination side. Such a setting will be reflected by opening the Server Equipment settings window in the Service Utility and then clicking the [OK] button. If the IP address on the Server Equipment settings window has not been updated to the new value, exit the Service Utility once, and perform Steps 1 through 10 again.

2.

Within 3 seconds of the display of the initial window, sequentially click its upper left and upper right corners.
Click the upper left corner first, and then the upper right corner.

00000118.ai

The Service Utility starts up and the Service Utility top window opens.

REFERENCE

1.

On the desktop screen, double-click the


The CR-IR 391CL starts.

icon.

If you have failed to perform Step 2 within 3 seconds of the display of the initial window and the application started up, perform the following procedure and then take the above Steps 1 and 2 again. 1. To terminate the application, click [Exit] on the login window. 2. Right-click the icon representing the CR-IR 391CL server in the task tray at the bottom right of the desktop screen. From the pop-up menu that appears, choose [Shut Down]. For the procedure to exit the CR-IR 391CL when it is up and running, see Preparatory work: Shutting down the CR-IR 391CL in Appendix 4: Setting the RU-Config.

3. 4.

Click [Connected equipment].


The Setting connection devices window opens.

Click [Image Reader].


The Settings necessary for the Image Reader window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MC 5-3

Appx MC 5-4
5.
Enter the changed IP address (e.g. 172.16.1.10).

8.

Check that the new value is shown in the IP address field and then click [OK].

CBS03161.ai

6. 7.

Click [OK].
The system returns to the Setting connection devices window.

Click [Server (this equipment)].


The Server Equipment settings window opens.
CBS03162.ai

The system returns to the Setting connection devices window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MC 5-4

Appx MC 5-5
9.
Click [Film Printer].
The Settings necessary for the film printer window opens.

12. Check that the new value is shown in the IP address field and then
click [Finish].

10. Select the printer and click [Change].

CBS93003.ai

The system returns to the Service Utility top window.


CBS93001.ai

11. Enter the changed IP address (e.g. 172.16.1.31) and click [Change].

13. Click [Exit].


The system returns to the desktop screen.

CBS93002.ai

The system returns to the Settings necessary for the film printer window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 5-5

Appx MC 5-6 2.4 Changing the CR-IR 391RU Setting


1.
Change the MASTER CL setting.
For details, see MU:1.15 EDIT CL NAME of CR-IR 391RU Service manual.

2.5 Changing the Service PC IP Address


For the procedure to make the setting, see the Service Manual of the DRYPIX 1000/2000/3000/4000/7000/PRIMA.
See IN: Installation in the Service Manual of the DRYPIX 1000/3000. See IN: Installation in the Service Manual of the DRYPIX 2000. See IN: Installation in the Service Manual of the DRYPIX 4000. See IN: Installation in the Service Manual of the DRYPIX 7000. See IN: Installation in the Service Manual of the DRYPIX PRIMA.

2.

Change the FTP Server IP Address setting.


For details, see MU 4.3 [1] of CR-IR 391RU Service manual.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 5-6

Appx MC 5-7 2.6 Changing the CR-IR 391CL IP Address


1. 2. 3. 4. 5. 6. 7.
Select [Control Panel] from the
The Control Panel window opens.

8. 9.

Click [OK].
The system returns to the Local Area Connection Properties window.

menu.

Click [OK].
The system returns to the Local Area Connection Status window.

Double-click Network and Sharing Center.


The Network and Sharing Center window opens.

10. Click [Close].


The system returns to the Network Connections window.

Select Manage network connection in the left side of the window.


The Network Connections window opens.

11. Close the Network Connections window.


The system returns to the desktop screen.

Double-click Local Area Connection.


The Local Area Connection Status window opens.

Click [Properties].
The Local Area Connection Properties window opens.

2.7 Restart the CR-IR 391CL , RU, and Printer


1. 2. 3.
Restart the CR-IR 391CL. Restart the RU. Restart the Printer.

Select Internet Protocol Version4 (TCP/IPv4) and click [Properties].


The Internet Protocol Version4 (TCP/IPv4) Properties window opens.

Perform the following setup steps:


I.

II.

00000430.EPS

Enter a new CR-IR 391CL IP address (e.g., 172.16.1.21). II. Enter a subnet mask.

I.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 5-7

Appx MC 5-8 2.8 Verifying the connection after IP address changes


1.
On the desktop, double-click the icon.

3. 4.

Set the cassette in the RUs cassette setting unit and make sure that images are transferred to the CR-IR 391CL. Click [EXIT].
The CR-IR 391CL exits and the system returns to the desktop screen.

The CR-IR 391CL starts up in about one minute. The RU initialization message appears on the CR-IR 391CL monitor. The RU becomes available in about two minutes.

CBS03163.ai

REFERENCE
If the RU initialization message does not appear on the CR-IR 391CLs monitor, restart both the CR-IR 391CL and RU.

2.

From the CR-IR 391CL user window (Registration), set patient data and exposure menu, and then click [Study start].
Both the CR-IR 391CL-AP window lamp and the RU panels cassette insertion lamp go on.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MC 5-8

Appx MC 6-1

Appendix 6 Setting up WakeOnLAN


This section describes how to set up the WakeOnLAN feature that automatically starts up the Image Reader in conjunction with the startup of the CR-IR 391CL.

3.

Click
The Tool Application Setup window opens.

NOTE
Turn off the UAC before installation. After the installation, turn on the UAC. For details, see Setting the User Account Control under 1.3.1 Installing and Setting Windows Vista.

1. Installing the WakeOnLAN Utility


1. 2.
Insert the CR-IR 391CL application CD into the DVD drive. Select Computer from the
The installation launcher starts up.

menu and

CBS03165.ai

double-click DVD RW drive (D:).

4.

Click
The Installation Wizard starts up.

CBS03166.ai

(Vx.x represents a version number.)


020-221-02E 01.08.2010 FM5563

CBS03164.ai

CR-IR 391CL Service Manual

Appx MC 6-1

Appx MC 6-2
5.
Click [Next].
A window for selecting the installation destination opens.

7.

Click [Next].
Installation starts. The completion window opens.

CBS03167.ai CBS03169.ai

6.

Click [Next].
The confirmation window opens.

8. 9.

Click [Finish].
The system returns to the Tool Application Setup window.

Click [Exit].
The installation launcher exits.

CBS03168.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 6-2

Appx MC 6-3

2. How to Acquire the RUs MAC Address


1. 2.
From the menu, select [All Programs] - [Fuji Film] - [RuPcTool].

3.

Click

RU PC-TOOL starts up.

Check the RU NAME and RU IP ADDR values for the RU you want to automatically wake up or start up. From the LIST OF EXISTING RU, select the RU to automatically start up, and click [MUTL].

RU TYPE CR-IRxxx: Model name of the RU to be connected is displayed.

INAppL0008.EPS

4.

Check the [MAC Address Display].

CBS03177.ai

The RU PC-TOOL/MUTL window opens.

INAppL0009.EPS

5. 6.

Close the RU PC-TOOL/MUTL window.


The system returns to the RU PC-TOOL window.

Close the RU PC-TOOL window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 6-3

Appx MC 6-4

3. How to Acquire the Printers MAC Address


For detail see 2.4 Details of PC-Utility Commands under MU:SERVICE MODE of the DRYPIX PRIMA Service Manual.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 6-4

Appx MC 6-5

4. Registering the Other Equipment


Register the other equipment you want to automatically start up in the following procedure.

3.

Specify the following settings.

I.

1.

From the [Start] menu, select [All Programs]-[Fuji Film][FF-WakeOnLAN Utility].


The WakeOnLAN Utility window opens.
II. III. IV.

CBS03171.ai

I. II. III. IV.

Enter the MAC address of the other equipment (Ex.: 00-c0-2d-13-4e-37). Enter the IP address of the other equipment (Ex.: 172.16.1.10). Enter the host name of the other equipment (Ex.: ruO). Make sure that the box is checkmarked (if you just want to register the equipment only but do not want to wake it up, uncheck the box).

4.
CBS03170.ai

Click [OK].
The system returns to the previous window.

2.

From the [Edit] menu, select [Register].


A window to register other equipment opens.

CBS03172.ai

5.

To register the second and subsequent pieces of other equipment, if any, repeat Steps 2 through 4.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 6-5

Appx MC 6-6
6. 7.
Bring the other equipment into a standby state. Select the other equipment on the list, and click [Select].
The equipments MAC address and host name appear on the right side.

9.

When you see that the other equipment has started, click [Save].
The confirmation window opens.

CBS03175.ai

10. Click [Yes].


The system returns to the WakeOnLAN Utility window.

11. Perform procedures from No.2 to No.10, register information about


your computer.

12. Click [Exit].


CBS03173.ai

The confirmation window opens.

8.

Click [Send Packet].


The result of sending the packet appears to the right of the button.

CBS03176.ai

13. Click [Yes].


The system returns to the desktop screen.

NOTE
Return the UAC to on. For details, see 1.10.5 Setting the User Account Control (Activate).

CBS03174.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MC 6-6

Appx MC 6-7

5. Testing Automatic Startup


After setting up the WakeOnLAN feature, check to see that the RU automatically starts up in conjunction with the startup of the CR-IR 391CL.

1. 2. 3. 4. 5. 6. 7.

If the PC is up and running, turn OFF the PC. If the RU is up and running, turn OFF the breaker switch in the lower portion of the RUs side. If the DRYPIX PRIMA is up and running, turn OFF the breaker switch in the lower portion of the DRYPIX PRIMAs side. Turn ON the RUs breaker switch alone. Keep pressing the Stand-by switch to bring the RU into stand by state. Turn ON the DRYPIX PRIMAs breaker switch alone. Turn ON the PC, and start up the CR-IR 391CL application. At this time, check to see that the RU and DRYPIX PRIMA which has been in its standby mode turns ON now and startup operation is performed.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 6-7

Appx MC 6-8
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 6-8

Appx MC 7-1

Appendix 7 Uninstalling APs


This appendix describes the procedures for uninstalling the following APs: CR-IR 391CL RU-AP RU PC-TOOL

1. CR-IR 391CL
1. 2. 3. 4. 5.
Select Control Panel from the
The Control Panel window opens.

menu.

Double-click [Program and Features].


The Program and Features window opens.

Select the FCR Application.


The selected item is then highlighted.

Click [Uninstall].
A confirmation window opens.

Click [Yes].
The uninstallation window opens. After a while, a command prompt window opens.

NOTE
Although a message saying Preparing to install opens on the screen, what is actually going to be performed is uninstallation.
After some seconds, a message saying Press any key to continue... opens in the command prompt window.

6.

Press the <Enter> key.


The command prompt window closes. Uninstallation processing continues. When it has finished, the system returns to the Add or Remove Programs window.

7.

Close the Program and Features window and Control Panel.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 7-1

Appx MC 7-2

2. RU-AP
To uninstall the RU-AP, use the RU PC-TOOL.
For detail see RU Service Manual.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 7-2

Appx MC 7-3

3. RU PC-TOOL
NOTE
Use the RU-CD to uninstall the RU PC-TOOL. Do not uninstall the RU PC-TOOL from Program and Features in Control Panel because an improper uninstallation results.

For detail see RU Service Manual.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 7-3

Appx MC 7-4
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 7-4

Appx MC 8-1

Appendix 8 Setting the BIOS 1. Setting the Dell OptiPlex 760/780


Setup Items
Set up each value of items in the table below.
Item
Drives Performance

Setup Procedure

1. 2. 3.

Turn ON the monitor and PC power switches.


The PC starts running.

Press the <F12> key when F12 Boot Options appears at the upper right corner of the window. Select Performance Multi Core Support and place a checkmark to Enable Multi Core Support.
Settings General Drives System Configuration Video Performance Multi Core Support Intel(R) SpeedStep TM C States Control Limit CPUID Value HDD Acoustic Mode
MCApp06006.ai

Description
SATA-2 Multi Core Support SpeedStep Off On Off

Setup Value

Multi Core Support Enable Mutli Core Support

This field specifies whether the p performance of some application

When the setting is changed, [Apply] become active at the lower right corner of the window.

4. 5.

Click [Apply]. Click [Exit].


The PC restarts.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MC 8-1

Appx MC 8-2
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 8-2

Appx MC 8-3
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 8-3

Appx MC 8-4
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MC 8-4

Appx MC 9-1

Appendix 9 Procedure for Changing the Computer Name


Preparatory work
Prior to starting the necessary work, check the following. Terminate currently used software including the CR-IR 391CL. Also terminate applications displayed in the task tray if possible.

1. Changing the Computer Name


1.
Select [Control Panel] from the
The Control Panel window opens.

menu.

2.

Double-click

Overall operation flow


1. Changing the Computer Name

The System window opens.

3.

Click Change settings.

2. Registering with the Service Utility 2.1 Starting the Service Utility 2.2 Cautions when an Error is Displayed

3. Checkup Work

MCApp12001.ai

The System Properties window opens.

MCApp12002.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MC 9-1

Appx MC 9-2
4. 5.
Click .

7.
.

The Computer Name/Domain Changes window opens.

Confirm that the changed computer name is shown, and click .

Change Computer name:, and click

MCApp12005.ai

The confirmation window for restarting opens.


MCApp12003.ai

The confirmation window for restarting opens.

MCApp12006.ai

MCApp12004.ai

8. 9.

Click
The PC restarts.

6.

Click

The system returns to the System Properties window.

After the PC is restarted, input the following when the login window opens. Click then [OK].
Username : fujicr

Password : system For the procedures that follow, see 2.1 Starting the Service Utility.

NOTE
Be sure to start the service utility right after logging in. If the application starts up automatically without implementing the service utility, 49500 error and 20110 error occur.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MC 9-2

Appx MC 9-3

2. Registering with the Service Utility


2.1 Starting the Service Utility
NOTE
After changing the system settings, be sure to start the service utility. By starting the service utility, the computer name is automatically retrieved from the system settings and registered to the database.

4.

Confirm that the changed computer name is shown for Host name.

REFERENCE
At this time, the computer name is retrieved automatically from the system settings, registered to the database, and it is saved when exiting the service utility.

1.

After restarting the OS, start the service utility.


For the starting procedures for the service utility, see 2. Starting, Logging-in to, and Exiting the Service Utility under MU: Maintenance Utility.

The Service Utility top window opens.

2. 3.

Click [Simplified setup wizard].


The Simplified setup wizard window opens.

MCApp12009.ai

5. 6. 7.

Click [Next] several times until the Service Utility top window opens.
The system returns to the Service Utility top window.

Click [Next] several times until the Server equipment settings window opens.
The Server equipment settings window opens.

Click [EXIT].
The system returns to the desktop screen.

Double-click the CR-IR 391CL server application icon.


CR-IR 391CL starts up.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MC 9-3

Appx MC 9-4 2.2 Cautions when an Error is Displayed


When CR-IR 391CL starts up without starting the service utility, the following error window opens.

3. Checkup Work
For detailed procedures, see 5. Checkup Work under IN: Installation.

MCApp12007.ai

When the error window opens, perform the following procedures.

1.

Click

The following error window opens.

MCApp12008.ai

2. 3.

Click

Perform 2.1 Starting the Service Utility.

After implementing the simplified setup wizard of the service utility, the error will not be displayed.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MC 9-4

MU-I

CR-IR 391CL Service Manual

MU: Maintenance Utility

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-I

MU: Maintenance Utility

MU-II
Reason
New release (FM5535) Revision for software V1.1(B) (FM5563) Changes in pagination (FM5563)

Control Sheet
Issue date
04/28/2009 01/08/2010

Revision number
01 02

Pages affected
All pages 2, 11, 17, 27, 28, 32, 41 to 45, 59, 104 to 106 Appx MU 1-2, 3, 7, 2-1, 4, 3-1, 2, 4, 4-1, 2, 5-1 46 to 58, 60 to 103

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-II

MU-1

1. Overview of Service Utility Functions


Service utility tools used for installing or servicing the CR-IR 391CL are collectively referred to as the Service Utility.

Service settings
System
Performs setup concerning, for instance, the user environment, operating style, and image processing.

REFERENCE
For backing up or restoring data for servicing purposes, use a utility named Backup Utility, which differs from the Service Utility. The main functions of the Backup Utility are as follows: Backup Backs up patient information, setup information, and log information. Restore Restores patient information and setup information. Collecting logs for maintenance purpose Collects log information. For details on the Backup Utility, see Appendix 1: Backup Utility. This section describes the details of the Service Utility. The Service Utility has the following functions:

Connected equipment
Sets the equipment to be connected to the CR-IR 391CL. System gradation correction process setup Sets the gradation correction file (LUT).

Linkage function
Sets a function that can be exercised in coordination with external equipment.

Film annotation characters


Sets the character string to be printed at the time of film output and specifies its format.

Person name
Specifies the person name format.

Maintenance tools
Database Utility
Initializes or rebuilds a database.

NOTE
To operate the CR-IR 391CL system program (including utility programs), Windows Explorer must be shut down. Operating the program with Windows Explorer up and running may cause a problem, such as system hang-up or media error, to occur. However, this does not apply when the procedure where to start up from Windows Explorer is determined.

Acquiring EDR backup data


Acquires or stores EDR backup data about a local image.

Connection check
Checks the connections to the equipment that is set through Connected equipment under Service settings.

Simplified setup
Simplified setup wizard
Opens a wizard that steps you through the process of interactive setup.

Log display/edit
Displays or clears the number of IP exposures (IP exposure count).

Event log display


Starts Event Viewer of the OS.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-1

MU-2

2. Starting, Logging-in to, and Exiting the Service Utility


This section describes the procedures for starting, logging-in to, and exiting the Service Utility.

1.

When the PC power is ON


When the CR-IR 391CL is running, right-click the CR-IR 391CL server icon in the task tray, which is located in the lower right corner of the desktop screen.

Starting the Service Utility


The procedure for starting the Service Utility differs depending on whether the CR-IR 391CL system power is ON or OFF.

IN000402.ai

2. 3. 4. 5.

The right-click menu opens.

Click [Exit]. When the CR-IR 391CL shutdown message appears, click [OK].
The CR-IR 391CL shuts down.

1. 2.

When the PC power is OFF


Turn ON the PC power.
Windows Vista starts up. After about one minute, the CR-IR 391CL starts.

Double-click the

icon on the desktop.

When the initial window opens, sequentially click its upper left and upper right corners within a period of 2 to 3 seconds.
Click the upper left corner first, and then the upper right corner.

The CR-IR 391CL starts in about 1 minute.

When the initial window opens, sequentially click its upper left and upper right corners within a period of 2 to 3 seconds.
Click the upper left corner first, and then the upper right corner.

00000118.ai

The ServiceUtilityAuthentication window opens. The ServiceUtilityAuthentication window opens.

00000118.ai

MU00001 .ai

MU00001 .ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-2

MU-3
Logging-in to the Service Utility
To log in to the Service Utility, enter a password for authentication.
For details on Service Utility startup, see under Starting the Service Utility.

Exiting the Service Utility

1.

In the Service Utility top window, click [EXIT].

1.

Start the Service Utility.


The ServiceUtilityAuthentication window opens.

MU00001 .ai

2.

Enter the password fieldengineer.

NOTES
Enter the password by using 1-byte lower-case characters. The entered password characters appear as asterisks (*).

MU000001.ai

The system returns to the desktop screen.

3.

Click [OK].
The Service Utility top window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-3

MU-4

3. Top Window
The Service Utility top window, which opens upon login, looks like the figure below.

XI. For details on the procedure for Log display/edit, see under 7.4 Log Display/Edit. XII. For details on the procedure for Event log display, see under 7.5 Event Log Display.

I. II. III. IV. V. VI. VII. VIII. IX. X. XI. XII.

MU000028.ai

I. II.

For details on the setup procedure for use with the Simplified setup wizard, see under 5. Simplified Setup Wizard. For details on the procedure for setting the System, see under 6.1 System.

III. For details on the procedure for setting the Connected equipment, see under 6.2 Connected Equipment. IV. For details on the procedure for setting the Linkage function, see under 6.3 Linkage Function. V. For details on the procedure for setting the Film annotation characters, see under 6.4 Film Annotation Characters.

VI. For details on the procedure for setting a Person name, see under 6.5 Person Name. VII. For details on the procedure for Modality setting, see under 6.6 Modality Settings. VIII. For details on the procedure for the Database Utility, see under 7.1 Database Utility. IX. For details on the procedure for Acquiring EDR backup data, see under 7.2 Acquiring EDR Backup Data. X. For details on the procedure for Connection check, see under 7.3 Connection Check.
020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-4

MU-5

4. Regional and Language Options Settings


Prior to performing necessary settings using the Service Utility functions, perform OS settings according to the region where the equipment is to be installed.

3. 4. 5.

Click the Formats tab to select a language (region) to use from the Current format pull-down menu. Click [Customize this format].
The Customize Regional Options window then opens.

1.

Select [Control Panel] from the [Start] menu.


The Control Panel is displayed. If the window is not in the Classic View mode, click [Classic View] to change the display to Classic View.

Select the Date tab.

2.

Double-click [Regional and Language Options].


The Regional and Language Options window opens.
MU000403.ai

MU000402.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-5

MU-6
6.
Following examples shown in the table below, enter a date from the keyboard in the [Short date:] box of the [Date formats] field.

9.

Select the Time tab.

CAUTION
A date entered will not be displayed correctly if the order to display year/ month/day used in the CR-IR 391CL system is different from that of the OS date format. Because this is used for important information, including the date of study and the like, it is essential to perform a date setting on the OS side carefully at this step. For details of settings of the date format used in the CR-IR 391CL system, see under 5.3 System Settings.
Date format used in the CR-IR 391CL
Japanese date (S62.10.07) ANSI long date (1987.OCT.07) ANSI short date (1987.10.07) American long date (OCT.07.1987) American short date (10.07.1987) European long date (07.OCT.1987) European short date (07.10.1987)

Date format used in the OS short Date format


yy/MM/dd yyyy/MM/dd yyyy/MM/dd MM/dd/yyyy MM/dd/yyyy dd/MM/yyyy dd/MM/yyyy
MU000404 ai

* Enter directly from the keyboard because some formats are not displayed in the pull-down menu.

10. Select [HH:mm:ss] or [H:mm:ss] for the [Time format:] box setting.
CAUTION
Do not use tt representation. The CR-IR 391CL database will not be displayed correctly if [tt hh:mm:ss] or [tt h:mm:ss] is specified for the time format.

7.

Similarly, perform settings for the [Long date] field.

NOTE
When doing so, observe the order of entering year/month/day in the short date format determined at Step 6 above.

8.

Click [Apply].

11. Click [OK].


The system returns to the Regional and Language Options window.

12. Click [OK].


The system returns to the Control Panel.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-6

MU-7
Defining the character to be used as a decimal point
Select . (period) as the character to be used as a decimal point. If anything other than a period is selected, an error occurs when you select an image distribution destination with the QA function.

3.

1.

Check to see that the character specified in the Decimal symbol field is . (period). If not, change it to . (period). If, as a result of the above selection, the same symbol is selected for the Digit grouping symbol and Decimal symbol fields, change the symbol for the Digit grouping symbol field.

In the Control Panel window, double-click Regional and Language Options.


The Regional and Language Options window opens.

2.

Make sure that the Formats tab is selected and click [Customize this format].

RI000228.ai RI000226.ai

The Customize Regional Options window opens.

4. 5.

Click [OK].
The system returns to the Regional and Language Options window.

Click [OK].
The system returns to the Control Panel.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-7

MU-8

5. Simplified Setup Wizard


The simplified setup wizard interactively performs the following setup procedures in the order named. The setup items vary with the selected options.
5.1 Starting the Simplified Setup Wizard 5.2 Setting the Date and Time 5.3 System Settings 5.4 Server Equipment Settings 5.5 Setting the Image Reader 5.6 Setting the Film Printer (option) 5.7 Storage Setup for DICOM Storage Device (option) 5.8 Exiting the Simplified Setup Wizard

5.1 Starting the Simplified Setup Wizard


1.
Start the Service Utility.
The Service Utility top window opens.

MU000501.ai

This section describes the procedure to be performed when all the options are selected.

2.

Click [Simplified setup wizard].


The Setting PC (OS) date/time window of the Simplified setup wizard opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-8

MU-9 5.2 Setting the Date and Time


2.
Check the date, time, and time zone.

NOTE
Carefully check the date and time because they are important values for the study date and exposure time.

If the date, time, and time zone are incorrect, correct them and then click [Apply].

00000115.ai

MU000502.ai

1.

Click [Date/time change].


The Date and Time Properties window opens.

3. 4.

Click [OK].
The system returns to the Setting PC (OS) date/time window.

Click [Next].
The System settings window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-9

MU-10 5.3 System Settings


Use the System settings window to perform setup concerning the institution name, date/time format, and patient name format (Kanji), and the like.

1. 2.

Enter Institution name represented by single-byte alphanumerics (essential). Click the downward arrow mark ( select it. ) for Year/month/day format to

CAUTION
If the year/month/day format has been changed, be sure to change the setting of the OS short date format as well. For details of the necessary setting, see 4. Regional and Language Options Settings.
Setting
Japanese date (S62.10.07) ANSI long date (1987.OCT.07) ANSI short date (1987.10.07) American long date (OCT.07.1987) American short date (10.07.1987) European long date (07.OCT.1987) European short date (07.10.1987) : Default

Description
Year+YY.MM.DD YYYY.MONTH.DD YYYY.MM.DD MONTH.DD.YYYY MM.DD.YYYY DD.MONTH.YYYY DD.MM.YYYY

3.

Click the downward arrow mark ( select a time format.


Setting
HH:MM:SS AM

) for Time format, and then


Description
12-hour format 24-hour format

MU000503 ai

HH:MM:SS : Default

4. 5.

Ensure that the [Inputting a patient name by multi-byte characters] check box is not checkmarked. Click [Next].
The [Setting the Server Equipment] window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-10

MU-11 5.4 Server Equipment Settings


Use the Setting the Server Equipment window to perform setup concerning the CR-IR 391CL server equipment name, software keyboard, monitor, and the like.

4.

Click [Selection] under Monitor model.

IMPORTANT
For a locally procured LCD monitor, be sure to perform the procedure below: I. Insert an FD where the LUT file is stored into the FD drive. II. Click Update on the Monitor model selection window. III. Select an LUT for the added model and click [OK].
The Monitor model selection window opens.

MU000504.ai MCApp13001.ai

1. 2.

Enter the Equipment name (host name). Verify that CVXXXXXXXX is entered as the Host name and that 172.16.1.20 is entered as the IP address.
(NOTE: The XXXXXXXX portion represents an 8-digit serial number.)

For details on monitor models, see under 6.2.2 Monitor Settings.

5.

Select a monitor model and then click [OK].


The system returns to the [Setting the Server Equipment] window.

NOTE
The monitor settings are automatically entered. Although the Magnified Display (%) setting can be changed, do not change it now.
For details, see 6.2.2 Monitor Settings.

3.

To use the software keyboard, put a checkmark in the Use check box under ( ).

REFERENCE
The Software keyboard function is not implemented in V1.1(B) or later. This setting is not working.
020-221-02E 01.08.2010 FM5563

6.

Next, perform the following setup steps (DICOM and disk drive settings).

CR-IR 391CL Service Manual

MU-11

MU-12
Set up DICOM (Media Storage setting)
The procedure for setting information for this equipment concerning DICOM Media Storage is described below. DICOM Media Storage is used for image transfer to a DVD.

2. 3.

Enter an AE name (e.g., DVD) in the AE Name field under Media Storage setting. Click the downward arrow mark ( ) for Maximum pixel density size for a stored image, and then select a maximum pixel density size for a stored image.
Setting
ST HQ : Default Standard density High density

1.

Click [DICOM setting].


The Set up DICOM window opens.

Description

REFERENCE
Selecting HQ decreases the number of images that can be recorded on a DVD.
For the number of images that can be stored when the ST, HQ, compressed, or uncompressed option is selected, see under 1.6 Image Storage Performance of Product Specifications.

4.

Click the downward arrow mark ( ) for Whether or not to specify data compression for stored images, and then select a stored image compression option.
Setting
Image data compressed : Default

Description
Compresses the image (lossless).

Image data not compressed Leaves the image uncompressed.

REFERENCE
Selecting Uncompressed decreases the number of images that can be recorded on a DVD.
For the number of images that can be stored when the ST, HQ, compressed, or uncompressed option is selected, see under 1.6 Image Storage Performance of Product Specifications.

MU050007.ai

REFERENCE
The following items shown within the frame on the window above appear only when the respective options are installed. : DICOM Print option Print SCU settings Settings for Storage SCU : DICOM Storage option
020-221-01E 04.28.2009 FM5535

5.

When storing two-byte character (Kanji or other multi-byte character) information, put a checkmark in the Multi-byte character setup check box under ( ).

CR-IR 391CL Service Manual

MU-12

MU-13
Set up DICOM (Print SCU setting)
The procedure for setting information for this equipment concerning DICOM Print is described below.

4.

Put a checkmark in both the BasicGrayscalePrint and Verification check boxes under Presentation Context ( ).

REFERENCE
Verification is a service class for verifying the connection between DICOM devices. When verifying the connection, it is necessary to check Verification. For details on connection verification, see under 7.3 Connection Check.

1.

Click the Print SCU setting tab.

5.

Click [OK].
The system returns to the [Setting the Server Equipment] window.

Click

MU050009.ai

2. 3.

Enter an AE name (e.g., FCR-CSL) in the AE Name field under Print SCU setting. Specify the Timeout value (timeout value between DICOM messages: 300).

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-13

MU-14
Set up DICOM (Settings for Storage SCU) (option)
The procedure for setting information for this equipment concerning DICOM Storage output is described below.

1. 2.

Click [DICOM setting].


The Set up DICOM window opens.

Click the Settings for Storage SCU tab.

Click

MU050008.ai

3. 4. 5.

Enter an AE name (e.g., FCR-CSL) in the AE Name field under Settings for Storage SCU. Specify the Timeout value (timeout value between DICOM messages: 300). Click [OK].
The system returns to the [Setting the Server Equipment] window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-14

MU-15
Disk drive settings
The procedure for setting the DVD drive that is to be connected to the server equipment (CR-IR 391CL machine).

3.

Click [View] to specify the drive path.


The Browse for Folder window opens.

1.

Click [Disk drive settings].


The Disk drive settings window opens.

N000208.ai

4. 5.

Select the connected DVD drive (D:) and then click [OK].
The system returns to the Disk drive settings window.

Click the downward arrow mark ( ) for Disk format application type, and then select a disk format application type (Dedicated application).
Setting
Not specified Dedicated application OS

Description
Does not provide formatting. Provides formatting with the dedicated application. Provides formatting with an OS function.

: Default
MU000507.ai

2.

Enter a management disk drive name (e.g., DVD) in the Drive name field under [Setting a Disk Drive for Server Management].

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-15

MU-16
6.
Click [View] to specify the Dedicated format application path.
The Open window opens.

9.

Check what is selected for Drive to be created in Set up PDI and click [Edit].

MU060209.ai

Notepad starts.

10. Input a facility name.


N000209.ai

7.

11. From the File menu, select Overwrite.


The Save as... window opens.

Select C:\Program Files\FujiFilm\Hobbit\System\ FFUdfFmtToolForVista.exe on the folder selection window.


C:\Program Files\FujiFilm\Hobbit\System\FFUdfFmtToolForVista.exe is input automatically in the Dedicated format application path field.

12. Confirm the Character Code and click Save.


NOTE
Select ANSI or Unicode character code. Input data can be saved only when either ANSI or Unicode is selected.

8.

Input rD to the end of the path (r represents a single-byte space and D represents a DVD drive path).

REFERENCE
After the input as directed above, the description in the Dedicated format application path field will be as follows.

13. Select Close Notepad from the File menu.


Notepad window closes and the system returns to the Disk drive settings window.

14. Click [OK].


The system returns to the Setting the Server Equipment window.
MU000529.ai

15. Click [Next].


The Setting the Image Reader window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-16

MU-17 5.5 Setting the Image Reader


4.
Remove the Checkmark from Use in the Check the box to use Patient information display field ( ).

NOTE
To have the patient information be displayed, the relevant setting must be turned ON also on the RU side. In case of 391RU, be sure to set to OFF. For details of the procedure to use, see Appendix 4: Setting the RU-Config in MC: Checks, Replacement and Adjustment of Parts.

5.

Click [Next].
The [Setting the Film Printer] window opens (this window does not open if the option key is not installed).

If the film printer is not to be connected, proceed as directed under 5.7 Setting for DICOM Storage Device (option). If the general-purpose file output option is not selected, proceed as directed under 5.8 Exiting the Simplified Setup Wizard.

MU000509.ai

1. 2. 3.

Enter an Image Reader name (default: Image Reader) in the Equipment name field. Enter an Image Reader host name (default: RU0) in the Host name field. Enter an Image Reader IP address (default: 172.16.1.10) in the IP Address field.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-17

MU-18 5.6 Setting the Film Printer (option)


When connecting the film printer (option), perform the film printer setup procedure described below.

1.

Click [Add], or select the printer whose settings are to be changed and then click [Change].
The Adding film printers or Changing film printers window opens.

MU000511.ai

2. 3. 4. 5. 6.

Enter a film printer name (e.g., Printer) in the Equipment name field. Enter a film printer host name (e.g., fujiprinter) in the Host name field. Enter a film printer IP address (e.g., 172.16.1.30) in the IP Address field. Enter a film printer AE name (e.g., DRYPIX) in the DICOM AE name field. Enter a film printer port number (e.g., 17238) in the Port number field.

MU000510.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-18

MU-19
7.
Click [Detailed settings].
The Detailed settings for film printer window opens.

8.

Click [Printer model selection].


The Selecting default settings specific to film printer model window opens.

MU000513.ai

9.

Select a model and then click [OK].


The system returns to the Detailed settings for film printers window. In this instance, the settings for the selected model are displayed as default values.

10. Put a checkmark in both the BasicGrayscalePrint and Verification


check boxes under Supported abstract syntaxes ( ).

REFERENCE
Verification is a service class for verifying the connection between DICOM devices. When verifying the connection, it is necessary to check Verification.
MU000512.ai

For details on connection verification, see under 7.3 Connection Check.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-19

MU-20
11. Under Film sizes available for printout, specify the film sizes that
can be printed out. Put a checkmark in a check box ( ).

REFERENCE
In the default bin number field, specify a default bin that is used for film output when no collation value (collation based on the identification information) is complied with. For bin numbers, see the printer service manual.
III. Click [Setting details of bins]. The Setting details of bins window opens.

12. Click the downward arrow mark (


Setting
SH HQ : Default

) for Transferable image sizes, and then select a reception image size.
Description
Reception image size maximum density (ultra-high density). Reception image size maximum density (high density).

13. Click the downward arrow mark (


Setting
Not specified MAGAZINE BIN_I

) for Destination for film output, and then select a film output destination.
Description
Complies with the printer setting. Delivers the output to a magazine type printer. Delivers the output to the ejection tray on the top of the printer. Delivers the output to the sorter bin.
MU000514.EPS

PROCESSOR : Default

14. If BIN_I (sorter bin) is selected as the Destination for film output,
perform the following setup steps:
I. Click the downward arrow mark ( ) for Bin number identification information, and then specify the bin number identification information.
Setting
MPM code Anatomical region Not specified

IV. In accordance with the selection made under Bin number identification information, double-click the Key field and then enter a key. If MPM code is selected under Bin number identification information, enter an MPM code (e.g., 0200). If Anatomical region is selected, enter an anatomical region name (e.g., CHEST).

Description
Identifies the output bin by MPM code. Identifies the output bin by anatomical region. Complies with the printer setting.

: Default

II. Click the or mark for Default bin number and then specify the default bin number, or enter a default bin number from the keyboard.
MU000515.EPS

V. Double-click the Bin number field, and then enter a bin number.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-20

MU-21
15. If the Image size specification function for printers is supported, put
a checkmark in ( ). (When the DRYPIX Series is used, be sure to check the check box because the function is supported.)

19. Click the downward arrow mark (

) for Dealing with an image not accommodated within the printers image area, and then select the process to be performed for an image that is not accommodated within the printers image area.
Setting
DECIMATE CROP Decimates. Crops. Complies with the printer setting. Does not generate an output because the image is not accommodated within a recordable image frame.

Description

16. If the printer supports 10-bit image prints, put a checkmark in


( ). (When the DRYPIX Series is used, be sure to check the check box because the 10-bit image prints are supported.)

Not specified FAIL

: Default

17. Click the downward arrow mark (


film type.

) for Film type and then select a


Description

20. Click the downward arrow mark (


Setting
REPLICATE BILINEAR NONE

) for How to magnify an image size, and then select an image magnification method.
Description
Provides interpolation by replicating a most similar neighboring color when creating a new pixel for magnification. Provides bilinear interpolation when magnifying the image. Provides bicubic interpolation when magnifying the image. Does not magnify or reduce the image.

Setting
Not specified CLEAR FILM Selects clear film. Selects blue film.

Complies with the printer setting.

BLUE FILM PAPER

Selects a paper printout (this option can be selected when a DICOM printer that can generate a paper output is connected).

CUBIC : Default

: Default * The DRYPIX Series cannot generate paper printouts.

18. Click the downward arrow mark (


Setting
3.0 3.6

) for Maximum film density (Dmax) and then specify the maximum film density.
Description
Issues an output request to the printer with the maximum density set at 3.0. Issues an output request to the printer with the maximum density set at 3.6.

REFERENCE
Bilinear interpolation When a new pixel is to be generated for magnification, its color is created by averaging the colors of four (linear) neighboring pixels (upper, lower, right, and left pixels). Bicubic interpolation When a new pixel is to be generated for magnification, its color is created by averaging the colors of eight (cubic) neighboring pixels (upper, lower, right, and left pixels and pixels at four corners).

: Default

NOTE
The printer setting should be basically complied with. This setup step need not be performed for the DRYPIX Series. For details, see the printer service manual.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-21

MU-22
21. If CUBIC was selected in Step 20 as the image magnification
method, enter a smoothening type in the Smoothening type field. (If an image magnification method other than CUBIC was selected in Step 20, do not enter a smoothening type because the Smoothening type field does not become active.)

5.7 Setting for DICOM Storage Device (option)


When the optional DICOM storage device is to be connected, perform the DICOM storage setup procedure described below.

NOTE
For the DRYPIX Series, only the SMOOTH, MEDIUM, and SHARP options are selectable (SMOOTH is selected by the default).

22. Click [OK].


The system returns to the Adding film printers window.

23. Click [Add].


The system returns to the [Setting the Film Printer] window.

24. Verify that the added or changed film printer is displayed in the list.

MU000516.ai

25. Click [Next].


The Settings for DICOM Storage Device window opens (this window does not open if the option key is not installed).

MU050001.ai

If the general-purpose file output option is not selected, proceed as directed under 5.8 Exiting the Simplified Setup Wizard.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-22

MU-23
1.
Click [Add], or select the DICOM storage device whose settings are to be changed and then click [Change].
The Addition of DICOM Storage Device or Change of DICOM Storage Device window opens.

7.

Click [Detailed settings].


The Advanced settings for DICOM Storage Device window opens.

MU050002.ai

2. 3. 4. 5. 6.

Enter the name of the DICOM storage device in the [Equipment name] field. Enter the host name of the DICOM storage device in the [Host name] field. Enter the IP address of the DICOM storage device in the [IP Address] field. Enter the AE name of the DICOM storage device in the [DICOM AE name] field. Enter the port number of the DICOM storage device in the [Port number] field.

MU050003.ai

8. 9.

Put a checkmark in both the CRImageStorage and Verification check boxes under [Supported abstract syntaxes_transfer syntaxes]. Perform setup for [Supported abstract syntaxes_transfer syntaxes] in accordance with the transfer syntax for the storage device.

10. Select HQ as the [Maximum pixel density size receivable]. 11. If the storage device supports multi-byte characters, put a checkmark
in the Supported check box under [Setting multi-byte characters.].

12. Click [OK].


The system returns to the Addition of DICOM Storage Device or Change of DICOM Storage Device window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-23

MU-24
13. Click [Add].
The system returns to the [Settings for DICOM Storage Device] window.

5.8 Exiting the Simplified Setup Wizard

MU000522.ai

1.

Click [Finish].
The system returns to the Service Utility top window.

The Simplified setup wizard is now closed.

IMPORTANT
For an output device set up using the Simplified setup wizard, be sure to use the User Utility to perform Setting a destination for image output.

MU050004.ai

14. Click [Next].


The Simplified setup wizard complete window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-24

MU-25

6. Service Settings
The service settings are used, for instance, for a system configuration change or version upgrade.

6.1 System
Perform basic setup for the CR-IR 391CL system as directed below.

1. 2.

Start the Service Utility.


The Service Utility top window opens.

Click [System].
The System settings window opens.

MU000015.ai MU000002.ai

Name
System Connected equipment Linkage function Film annotation characters Person name Modality settings

Description
Performs basic setup for the CR-IR 391CL system. Performs setup for the equipment to be connected to the CR-IR 391CL. Sets the function to be exercised in coordination with another system. Sets the character string to be output onto film and specifies its format. Performs setup for the conversion of an input person name. Perform LUT setting corresponding to each modality.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-25

MU-26
3.
Click the downward arrow mark ( ) for

4.

Double-click the Setup value field on the right-hand side.

to open the pull-down menu, and then select the category to be displayed.
The items classified under the selected category appear in the Setup item list. The following categories are selectable: Localize setting Settings related to the date (year/month/day) and time. Setting for institution Settings related to a hospital name. Setting for entering patient name Settings related to patient name input. Setting for image collection Settings related to an image read. Setting for image browsing Settings related to image display format changes in the viewer window. Setting for general-purpose file output Settings related to the output of a general-purpose file that can be viewed with another tool. Image incidental information Setting related to the image process change flag. Print format Settings related to image output. Film character setting Settings related to a character string that is output together with an image. Setting for output function Settings related to image output. Operation (low frequency) setting Settings related to operations. Setting for analysis Settings related to log acquisition. Settings for endoscopic image import Settings for support to import of endoscopic images. All All the above settings.
Setup value field
MU000003.ai

5.

Change the setup value.


For details on the settings, see under Settings accessible from the System settings window.

If the double-clicked field looks like field) I. Enter desired text from the keyboard. If the double-clicked field looks like menu)
I. Click the downward arrow mark ( ) for

(direct input

(pull-down
and

select a desired setup item from the pull-down menu.

If the double-clicked field looks like downward arrow marks)


I.

(upward and

Click the or and change the value as desired, or enter a desired value from the keyboard.

6.

Click [OK].
The system returns to the Service Utility top window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-26

MU-27
Settings accessible from the System settings window
Localize setting
Number
1-1

Setup item name


Date display format

Option
0 : Japanese date (S62.10.07) 1 : ANSI long date (1987.OCT.07) 2 : ANSI short date (1987.10.07) 3 : American long date (OCT.07.1987) 4 : American short date (10.07.1987) 5 : European long date (07.OCT.1987) 6 : European short date (07.10.1987) 0 : HH:MM:SS AM (12-hour format) 1 : HH:MM:SS (24-hour format) Yes No

Description
Date format (commonly applied to all date expressions including birth date input, display, and film output). * The date format to be specified here must be the same, in terms of order of year/month/day, as the OS date format. For details see 4. Regional and Language Options Settings. Sets the time display format. Whether to store images in NAS.

Remarks
Simplified setup wizard

1-2 1-3

Time display format Enable images stored in HDD

Simplified setup wizard

: Default setting, *: Note

Setting for institution


Number
2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8

Setup item name


Facilities name em-size Institution name en-size Institution information 1 (Use paper print.) Institution information 2 (Use paper print.) Institution information 3 (Use paper print.) Institution information 4 (Use paper print.) Institution logo mark (Use paper print.) System name for which search conditions are displayed on the study list

Option
Up to 15 2-byte characters. Up to 60 1-byte characters. 40 bytes max. 40 bytes max. 40 bytes max. 40 bytes max. 255 bytes max. ( PC)

Description
Sets a hospital name (2-byte characters). Sets a hospital name (1-byte characters). Medical institution information that is output as a footer on a paper printout. Medical institution information that is output as a footer on a paper printout. Medical institution information that is output as a footer on a paper printout. Medical institution information that is output as a footer on a paper printout. A path to a hospital mark (JPEG, etc.) that is output onto a paper printout.

Remarks
Simplified setup wizard Simplified setup wizard This option item is not used. This option item is not used. This option item is not used. This option item is not used. This option item is not used. Simplified setup wizard

: Default setting, *: Note

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-27

MU-28
Setting for entering patient name
Number
3-1

Setup item name

Option

Description

Remarks
Simplified setup wizard

Whether an input column for Specifies whether or not to display a Kanji patient name. Yes : Displays a Kanji patient name. kanji patient name is displayed No : Does not display a Kanji patient name. or not. Character string length of patient ID (up to 64 characters) 1 to 64 ( 10) Specifies the patient ID character string length.

3-2

Do not change the patient ID character string length after an operation. Since the number of input characters is limited, you may not able to conduct a search by patient ID.

3-3 3-4

Padding method of patient ID Default patient ID value to be given when the actual patient ID is unavailable in the data received via DICOM communication from the ultrasound device.

Specifies the patient ID padding method. 0 : No Padding 1 : Pad with zero to the head (0001234567) (max 10 characters)

: Default setting, *: Note

Setting is also possible with the user utility.


Number
4-1

Setup item name


Whether to use guidance function on the exposure screen. Yes : Enable No : Disable

Option

Description
(Not used.)

Remarks

4-2

Whether to perform automatic Yes : Perform automatic output. output of the studies re No : Does not perform automatic output. verified (previously-verified studies which were verified once again after necessary modifications have been applied). Display unit of size measurement 0 : m 1 : cm 2 : inch 3 : feet 0 : kg 1 : g 2 : stone 3 : pound Unit used for display by the system : Size

(Not used.)

4-3

4-4

Display unit of weight measurement

Unit used for display by the system : Weight

: Default setting, *: Note

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-28

MU-29
Setting for image collection
Number
5-1

Setup item name


IP size selection (inch/metric) System ID (A-Z) Set number: Minimum value Set number: Maximum value 0 : Inch 1 : Metric A to Z ( A) 1 1 to ZZ ( 9Z)

Option

Description
Specifies the IP size code (specifies whether the inch or metric sizes are used to represent the 14"14"/35cm35cm size and 14"17"/3543cm size). System ID (A to Z). (The system ID is a machine-specific ID and used, for instance, for study number automatic issuance.) Set number minimum value. (This value must be smaller than the set number maximum value.) Set number maximum value. (This value must be greater than the set number minimum value.) Specifies whether or not to perform a pantomography process (perform a trimming process when the pantomography menu is selected and the image size is 1210inch size). Specifies whether or not to provide GS conversion for 1824cm/810inch standard-density images.

Remarks

5-2 5-3 5-4 5-5

Whether Pantomography Yes : Performs a pantomography process. processing is executed or not. No : Does not perform a pantomography process. Whether GS conversion for six Ts/1824 images is performed or not. Yes : Provides conversion. No : Does not provide conversion.

5-6

: Default setting, *: Note

Setting for image browsing


Number
6-1 6-2 6-3

Setup item name


Display unit of measurement result Number of rows displaying additional image information Number of lines displaying additional image information 0 : cm 1 : Inch 1 to 10 ( 3) 1 to 15 ( 7)

Option

Description
Specifies the unit in which the length and the heart-to-ribcage ratio are displayed. Position selection window grid size (number of columns). Position selection window grid size (number of rows).

Remarks

: Default setting, *: Note

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-29

MU-30
Setting for general-purpose file output
Number
7-1

Setup item name

Option

Description
General-purpose file output destination.

Remarks
This option item is not used.

Path name at general-purpose (255 characters max.) file output destination at the time of automatic output. General-purpose file format at 0 : JPEG Lossy the time of automatic output. 1 : Bitmap General-purpose file reduction 1 to 100 ( 100) rate % at the time of automatic output.

7-2 7-3

General-purpose file format for automatic output

This option item is not used.

General-purpose file image reduction ratio (%) for automatic output (valid This option item is not used. for JPEG and BMP files). This option item is not used.

7-4

General-purpose file image General-purpose file image quality (compression ratio) for automatic 0 : Super High : Superhigh image quality quality at the time of automatic (low-energy compression). output (valid for JPEG files). output (compressibility) 1 : High Quality : High image quality (standard-energy compression). <effective when JPEG is selected> 2 : Standard : Standard image quality (highenergy compression). Name generation rule for general-purpose file at the time of output.

7-5

General-purpose file name generation rules. This option item is not used. 0 : ImageNumber Img + serial number.txt * If the host name length exceeds 10 characters when Type1 or Type2 is 1 : Type1 Host name + date + serial number.txt selected, the application performs an automatic edit to reduce the Host name: 10 characters max.; date: 2 length to 10 characters. characters at all times; serial number: 4 characters at all times 2 : Type2 Patient ID + _ + study date (year/ month/day) + _ + ANK anatomical region + _ + serial number + _ + host name.txt Patient ID: 16 characters max.; study date: 6 characters at all times; host name: 10 characters max. 0 : ImageNumber 1 : Type1 2 : Type2 Name generation rules to be applied to a situation where an endoscope study image is automatically output as a general-purpose file. This option item is not used.

7-6

Name generation rule for general-purpose file at the time of output (For studies other than CR).

7-7

Default character strings to be - (max 64 characters) output to patient information text file.

Default character strings to be output to a patient information text file.

This option item is not used.

: Default setting, *: Note

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-30

MU-31
Linkage with the receipt computer
Number
8-1

Setup item name


Whether support is provided or not to linkage with the receipt computer. Device model linked to the receipt computer.

Option
Yes : Provides support. No : Does not provide support. 0 : None 1 : SANYO 2 : STANDARD 3 : TOSHIBA 4 : FUJITSU 5 : Dynamics Up to 16 1-byte characters ( Newve) 192.168.100.50

Description

Remarks
This option item is not used.

8-2

This option item is not used.

8-3

Host name of receipt computer <Linkage=SANYO> Internet Protocol address of receipt computer <Linkage=SANYO>

This option item is not used.

8-4

This option item is not used.

8-5

Port number for connecting to 1 to 65535 ( 9031) receipt computer <Linkage=SANYO> Cable format requesting patient information to receipt computer <Linkage=SANYO> Inquiry time-out value second <Linkage=SANYO> Preferential destination for patient information search <Linkage=SANYO> Shared folder for linkage with the receipt computer <Linkage= other than SANYO> Shared folder monitoring interval [sec] on linkage with the receipt computer <Linkage= other than SANYO> Port number for receiving cable messages from the receipt computer <Linkage=FUJITSU> 0 : A01 1 : A51

This option item is not used.

8-6

This option item is not used.

8-7 8-8

1 to 20 ( 15) 0 : Local DB 1 : ReceiptComp. MAX255

This option item is not used. This option item is not used.

8-9

This option item is not used.

8-10

1 to 300 ( 5)

This option item is not used.

8-11

1 to 65535 ( 5011)

This option item is not used.

: Default setting, *: Note

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-31

MU-32
Number
8-12

Setup item name


Receipt time-out value [msec] 1 to 1000 ( 1000) of continuous cable messages from the receipt computer <Linkage=FUJITSU>

Option

Description

Remarks
This option item is not used.

: Default setting, *: Note

Setting for image link


Number
9-1

Setup item name


Whether support is provided 0 : None or not to Image Link as well as 1 : SANYO its linkage device model. 2 : STANDARD Pipe name when named pipe is communicated <Link age=SANYO>

Option

Description

Remarks
This option item is not used.

9-2

McssPIDSycService

This option item is not used.

9-3

Whether patient ID is acquired Yes : Automatically acquires the patient ID. from the care card No : Does not automatically acquire the automatically when beginning patient ID. to inspect it newly or not? Required cable response time-out value second when the pipe is connected <Linkage=SANYO> User name when the pipe is connected <Linkage=SANYO> Password when the pipe is connected <Linkage=SANYO> 1 to 20 ( 5)

This option item is not used.

9-4

This option item is not used.

9-5

fujicr

This option item is not used.

9-6

system

This option item is not used.

9-7

Interval [msec] for monitoring 100 to 60000 ( 500) the common folder that checks requests for image display and study reservation/start, using the networking function. *Networking system = STANDARD

This option item is not used.

: Default setting, *: Note

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-32

MU-33
Image incidental information
Number
11-1

Setup item name


Activation of the image processing modification flag

Option
Yes : Validates the flag. No : Invalidates the flag.

Description
Specifies whether the image process change flag should be validated or invalidated for an image processing parameter change.

Remarks

: Default setting, *: Note

Print format
Number
12-1

Setup item name


Type specification of film margin (blank part)

Option

Description

Remarks

Specifies the paintout type of a margin (background) outside the image 0 : Margin depend on image ID display area. Conforms to the first frame if a format other than single is (default:Transparent) Either transparent or black depending used. on the image information. Transparent if nothing is specified by the image information. 1 : Margin depend on image ID (default:Black) Either transparent or black depending on the image information. Black if nothing is specified by the image information. 2 : Transparent Margin (Fix) Transparent at all times. 3 : Black Margin (Fix) Black at all times. 0 to 25 ( 0) Specifies the trimming amount [mm] (except for mammography).

12-2

Trimming volume [mm] (excluding Mammo)

Trimming amount
Yes : Generates framed image prints. No : Generates frameless image prints.

* Be sure to enter one or two 1-byte characters from the keyboard. Specifies whether bordered or borderless prints should be generated when 3543cm/1417inch, 3535cm/1414inch, 2636cm, 2430cm/ 1012inch, or 1824cm/810inch film is printed in the following patterns: 3543cm/1417inch Single format prints of a 3543cm/1417inch size image Single format prints of a 3535cm/1414inch size image Single format prints of an 1843cm size image 3535cm/1414inch Single format prints of a 3535cm/1414inch size image 2636cm Single format prints of a 1014inch size image 2430cm/1012inch Single format prints of a 1012inch size image 1824cm/810inch Single format prints of an 1824cm/810inch size image * If the output format is displaced, the image border is not displayed.

12-3

Whether or not there is a frame on the image when 1824 Single is formatted 1417, 1414,1843 / 810.

: Default setting, *: Note


020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-33

MU-34
Number
12-4

Setup item name


Whether or not there is a frame on the image when 1417, 1843LR, 2on1 are formatted.

Option
Yes : Generates framed image prints. No : Generates frameless image prints.

Description
Specifies whether bordered or borderless prints should be generated when an 1843cm size image is printed onto 3543cm/1417inch film in the LR or 2-on-1 format. * If the output format is displaced, the image border is not displayed. Specifies whether bordered or borderless prints should be generated when a 3543cm/1417inch, 1843cm, or 1824cm/810inch size image is printed onto 3543cm/ 1417inch film in the 4-on-1 format. Specifies whether bordered or borderless prints should be generated when a 1824cm size image (100% size) is printed onto 2636cm film in the LR or 2-on-1 format.

Remarks

12-5

Whether or not there is a Yes : Generates framed image prints. frame on the image when No : Generates frameless image prints. 1417, 1843, 810, 4on1 are formatted. Whether or not there is a frame on the image when 2on1 display of L&R breast images on B4 film (equal to 1824) is formatted. Whether or not there is a frame in the 810 mammo Single image formatted onto B4 film. Whether or not there is a frame in the output image equal to 1824. Yes : Generates framed image prints. No : Generates frameless image prints.

12-6

12-7

Yes : Generates framed image prints. No : Generates frameless image prints.

Specifies whether framed or frameless prints should be generated when (Not used.) a 1824cm/2430cm size mammographic image is printed onto 2636cm film in the single format or when a 1824cm size mammographic image is printed onto 1824cm/810inch film in the single format. Specifies whether framed or frameless prints should be generated when a 1824cm size (100%-size) image is printed. Specifies a menu code that does not print out the scale. * This setting is valid for images that are to be framed. * This setup can also be performed variously for each MPM code. Up to eight MPM codes can be specified (a wildcard character may be used to specify the MPM codes).

12-8

Yes : Generates framed image prints. No : Generates frameless image prints.

12-9

Setting of menu code in which [Dialog setup] (?3??) scale is not displayed For the setup procedure, see under (effective when setting is such Details of [dialog setup]. that image frame is added).

12-10

Specification of age display form

0: Age : Japanese version

Non-Japanese version 1: Date of birth Japanese version Non-Japanese version : Default setting, *: Note

Displays the age. Specifies the age display format. Example) 25 years old, 1 year and 8 * For DATE display, Date display format selected from Localize months old, 1 month setting is used. and 10 days old, 13 days old. Example) 25Y, 1Y8M, 1M10D, 13D. Displays the birth date. Generates an output in born on DATE form. Generates an output in DATE B form.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-34

MU-35
Number
12-11

Setup item name


Specification of right and left reversing mark display form

Option
0 : None Prints out no right-and-left reversal mark. 1 : R-reverse Not reversed: Displays no right-and-left reversal mark. Reversed: Displays . 2 : AP or PA Not reversed: Displays AP. Reversed: Displays PA.

Description
Specifies whether or not to output the right-and-left image reversal mark.

Remarks

12-12

Whether or not film character 0 : None area display is available when Does not generate a film output. 1824-Single is formatted 1 : Only area 1 half-size Film Displays film annotation character area 1417-Single/4on1, 1 only. 1843-LR/2on1/4on1, 810 2 : Only area 2 4on1 format, and 810 film Displays film annotation character area size. 2 only. 3 : Both Displays both film annotation character areas.

Specifies whether or not display the film annotation character areas when 3543cm/1417inch, 3535cm/1414inch, 2636cm, or 1824cm/ 810inch film is printed in the following patterns: 3543cm/1417inch Single or 4-on-1 format prints of a 3543cm/1417inch size image LR, 2-on-1, or 4-on-1 format prints of a 1843cm size image 4-on-1 format prints of a 1843cm/810inch size image 3535cm/1414inch Single format prints of a 3535cm/1414inch size image 2636cm Single format prints of a 1014inch size image 1824cm/810inch Single format prints of a 1824cm/810inch size image See under Film annotation character areas 1 and 2. Specifies the film annotation character area size for a situation where 3543cm/1417inch, 3535cm/1414inch, 2636cm, or 1824cm/ 810inch film is printed in the following patterns: 3543cm/1417inch Single format prints of a 3543cm/1417inch size image 3535cm/1414inch Single format prints of a 3535cm/1414inch size image 2636cm Single format prints of a 1014inch size image 1824cm/810inch Single format prints of a 1824cm/810inch size image Specifies the position and rotation of film annotation character areas 1 and 2 for a situation where a 3543cm/ 1417inch size image is printed onto 3543cm/1417inch film in the single or 4-on-1 format. * The settings are valid for all exposure menus. When performing setup for each MPM code, use setup item No.12-26. See under Film annotation character areas 1 and 2.

12-13

Film character area size when 0 : Standard a film equal to 1417 size is 1 : Large output.

12-14

Film character area position and rotation setting when half-size Film 1417-Single/ 4on1 is formatted (default rule)

[Dialog setup] ( 0010) For the setup procedure, see under Details of [dialog setup].

: Default setting, *: Note

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-35

MU-36
Number
12-15

Setup item name

Option

Description
Specifies the position and rotation of film annotation character areas 1 and 2 for a situation where a 4335cm/ 1714inch size image is printed onto 4335cm/1714inch film in the single or 4-on-1 format. * The settings are valid for all exposure menus. When performing setup for each MPM code, use setup item No.12-27. See under Film annotation character areas 1 and 2. Specifies the position and rotation of film annotation character areas 1 and 2 for a situation where an 1843cm size image is printed onto 3543cm/1417inch film in the LR, 2-on-1, or 4-on-1 format. * The settings are valid for all exposure menus. When performing setup for each MPM code, use setup item No. 12-28. See under Film annotation character areas 1 and 2.

Remarks

Film character area position [Dialog setup] ( 1131) and rotation setting when For the setup procedure, see under Single/4on1 half-size Film Details of [dialog setup]. 1714 (horizontal half-size)- is formatted (default rule)

12-16

Film character area position and rotation setting when half-size Film 1843-LR/2on1/4on1 is formatted (default rule)

[Dialog setup] ( 0010) For the setup procedure, see under Details of [dialog setup].

12-17

Film character area position and rotation setting when 1824-Single is formatted half-size Film 810-4on1 format and 810 size film (default rule)

[Dialog setup] ( 0010) For the setup procedure, see under Details of [dialog setup].

Specifies the position and rotation of film annotation character areas 1 and 2 for a situation where an 1824cm/810inch size image is printed onto 3543cm/1417inch film in the 4-on-1 format or an 1824cm/ 810inch size image is printed onto 1824cm/810inch film in the single format. * The settings are valid for all exposure menus. When performing setup for each MPM code, use setup item No.12-29. See under Film annotation character areas 1 and 2.

12-18

Film character area position and rotation setting when 810 and 1824-Single (90 degree-rotation available) are formatted. (default rule)

[Dialog setup] ( 1131) For the setup procedure, see under Details of [dialog setup].

Specifies the position and rotation of film annotation character areas 1 and 2 for a situation where a 90-rotated 810inch/1824cm image is printed onto 1824cm/810inch film in the single format. See under Film annotation character areas 1 and 2. Specifies the position and rotation of film annotation character areas 1 and 2 for a situation where a 3535cm/1414inch size image is printed onto 3535cm/1414inch film in the single format. * The settings are valid for all exposure menus. Specifies the position and rotation of film annotation character areas (default) for a situation where a 1014inch size image (100% size) is printed onto 2636cm film in the single format. Specifies the position and rotation of film annotation character areas (default) for a situation where a 1410inch size (2636cm landscape) image (100% size) is printed onto 2636cm film in the single format.

12-19

[Dialog setup] ( 0010) Film character area position and rotation when Osumi Film For the setup procedure, see under 1414- Single is formatted Details of [dialog setup]. (default rule) Film character area position and rotation when Single is formatted onto B4 film (equal to 1014) Film character area position and rotation when Single is formatted onto B4 film (equal to 1410 horizontal B4) (default rule) [Dialog setup] ( 0010) For the setup procedure, see under Details of [dialog setup]. [Dialog setup] ( 1131) For the setup procedure, see under Details of [dialog setup].

12-20

12-21

: Default setting, *: Note

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-36

MU-37
Number
12-22

Setup item name


Film character area position and rotation when LR on B4 film (equal to 1824) is formatted (default rule) Film character area position and rotation when 2on1 display on B4 film (equal to 1824) is formatted (default rule) Film character area position and rotation when 1012 size film and 2430-Single are formatted (default rule) Film character area position and rotation when 1012 size film, 2430-Single (90 degreerotation available) are formatted. (default rule) Film character area position and rotation setting when half-size Film 1417-Single/4on1 is formatted (user definition 1)

Option
[Dialog setup] ( 0010) For the setup procedure, see under Details of [dialog setup]. 0010 [Dialog setup] ( 0010) For the setup procedure, see under Details of [dialog setup]. [Dialog setup] ( 0010) For the setup procedure, see under Details of [dialog setup]. [Dialog setup] ( 1131) For the setup procedure, see under Details of [dialog setup]. [Dialog setup] ( None) For the setup procedure, see under Details of [dialog setup].

Description
Specifies the position and rotation of film annotation character areas (default) for a situation where an 1824cm size image (100% size) is printed onto 2636cm film in the LR format. Specifies the position and rotation of film annotation character areas (default) for a situation where an 1824cm size image (100% size) is printed onto 2636cm film in the 2-on-1 format.

Remarks

12-23

12-24

Specifies the position and rotation of film annotation character areas (default) for a situation where a 1012inch/2430cm size image is printed onto 2430cm/1012inch film in the single format. Specifies the position and rotation of film annotation character areas (default) for a situation where a 1012inch/2430cm size image is printed onto 2430cm/1012inch film in the single format (90 rotated).

12-25

12-26

Specifies the position and rotation of film annotation character areas 1 and 2 for a situation where a 3543cm/1417inch size image is printed onto 3543cm/1417inch film in the single or 4-on-1 format. * Perform setup for each MPM code (up to 8 pieces, wildcard characters unavailable). * The above settings take precedence over the settings defined under setup item No.12-14. See under Film annotation character areas 1 and 2. Specifies the position and rotation of film annotation character areas 1 and 2 for a situation where a 4335cm/ 1714inch size image (1417inch landscape) is printed onto 3543cm/1417inch film in the single or 4-on-1 format. * Perform setup for each MPM code (up to 8 pieces, wildcard characters unavailable). * The above settings take precedence over the settings defined under setup item No.12-15. See under Film annotation character areas 1 and 2.

12-27

[Dialog setup] ( None) Film character area position and rotation setting when For the setup procedure, see under Single/4on1 half-size Film Details of [dialog setup]. 1714 (horizontal half-size)- is formatted (user definition 2)

: Default setting, *: Note

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-37

MU-38
Number
12-28

Setup item name


Film character area position and rotation setting when half-size Film 1843-LR/2on1/4on1 is formatted (user definition 3)

Option
[Dialog setup] ( None) For the setup procedure, see under Details of [dialog setup].

Description
Specifies the position and rotation of film annotation character areas 1 and 2 for a situation where an 1843cm size image is printed onto 3543cm/1417inch film in the LR, 2-on-1, or 4-on-1 format. * Perform setup for each MPM code (up to 8 pieces, wildcard characters unavailable). * The above settings take precedence over the settings defined under setup item No.12-16. See under Film annotation character areas 1 and 2.

Remarks

12-29

Film character area position and rotation setting when 1824- Single is formatted half-size Film 810-4on1 format and 810 film size format (user definition 4)

[Dialog setup] ( None) For the setup procedure, see under Details of [dialog setup].

Specifies the position and rotation of film annotation character areas 1 and 2 for a situation where an 1824cm/810inch size image is printed onto 3543cm/1417inch film in the 4-on-1 format or an 1824cm/ 810inch size image is printed onto 1824cm/810inch film in the single format. * Perform setup for each MPM code (up to 8 pieces, wildcard characters unavailable). * The above settings take precedence over the settings defined under setup item No.12-17. See under Film annotation character areas 1 and 2. Specifies the position and rotation of film annotation character areas 1 and 2 for a situation where the image overlaps with a film annotation character area. See under Film annotation character areas 1 and 2. Specifies the position and rotation of film annotation character areas 1 and 2 for a situation where the image overlaps with a film annotation character area. See under Film annotation character areas 1 and 2. Specifies the image output position for a situation where a 1530cm, 3535cm/1414inch, or 4343cm/1717inch size image is printed onto 3543cm/1417inch film in the single format.

12-30

Position and rotation setting in [Dialog setup] ( None) film character area when For the setup procedure, see under image and film character area Details of [dialog setup]. come in succession (user definition 5) Position and rotation setting in [Dialog setup] ( None) film character area when For the setup procedure, see under image and film character area Details of [dialog setup]. come in succession (user definition 6) Image display position specification when 4343 Single is formatted half-size Film 1530 and 3535 (part display) Setting for validity/invalidity of reduced output onto an 810film Reduction ratio when 2 on 1 display of L&R breast images on B4 film (equal to 1824) is printed out. Yes : Moves to the film top. No : Does not move.

12-31

12-32

12-33

Yes : Reduces the image to 1824cm/810 inch film size. No : Generates a 100%-size image. 0 : 86% 1 : 100%

Specifies whether a 3543cm/1417inch, 3535cm/1414inch, or 2430cm/1012inch size image in the single format should be reduced and output to 1824cm/810inch film. See under Output film determination sequence Specifies the print reduction ratio for a situation where an 1824cm size image is printed onto 2636cm film in the LR or 2-on-1 format.

12-34

: Default setting, *: Note


020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-38

MU-39
Number
12-35

Setup item name


Setting for Whether or not an expansion print is executed when an image with the standard density format print is output.

Option
Yes : Generates a magnified print. No : Does not generate a magnified print.

Description
When 3543cm/1417inch film is loaded, the 3543cm or 3535cm standard-density 1-image format is magnified and printed onto the 3543cm/1417inch film. When 3535cm/1414inch film is loaded, the 3535cm standard-density 1-image format is magnified and printed onto the 3535cm/1414inch film.

Remarks

: Default setting, *: Note

Film character setting


Number
13-1

Setup item name


Whether or not EDR mode is displayed.

Option
Yes : Generates an output. No : Does not generate an output.

Description
Specifies whether or not to output EDR mode settings to the film. * The letter output to the film is A for the AUTO mode, S for the SEMI mode, F for the FIX mode, and S for the SEMI-X mode. Specifies whether or not to output image processing conditions to the film. Specifies whether or not to output the L value, S value, and CS/SS information to the film. Specifies whether or not to output the exposure time to the film. * The Japanese version outputs the title Exposure date to the left of the exposure time. Non-Japanese versions output EXP:. Specifies whether or not to output the routine/pair information to the film. * Film output example: RT-01, TS101 Specifies whether or not to output an exposure menu name to the film. Specifies whether or not to output the image compression code information to the film. * The Japanese version outputs the title Compression ratio to the left of the image compression code information. Non-Japanese versions output CC:.

Remarks

13-2

Whether or not image processing conditions are displayed.

Yes : Generates an output. No : Does not generate an output.

13-3

Whether or not L value, S Yes : Generates an output. value, CS, and SS information No : Does not generate an output. are displayed. Whether or not exposure time is displayed. Yes : Generates an output. No : Does not generate an output.

13-4

13-5

Whether or not routine and class processing information are displayed. Whether or not menu names are displayed. Whether or not compression code is displayed.

Yes : Generates an output. No : Does not generate an output.

13-6 13-7

Yes : Generates an output. No : Does not generate an output. Yes : Generates an output. No : Does not generate an output.

13-8

Whether or not barcode is displayed.

Yes : Displays a barcode. No : Does not display a barcode.

Specifies whether or not to output a barcode number to the film.

Barcode is not supported.

: Default setting, *: Note

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-39

MU-40
Number
13-9

Setup item name


Setting for the maximum value 0 to 64 ( 20) of en-size character numbers for the patient names to be film-output. Setting for the maximum value 0 to 64 ( 10) of em-size character numbers for the patient names to be film-output.

Option

Description
Specifies the maximum number of 1-byte patient name characters to be printed out. * If the employed setting is greater than the default value (20), the other information may not fit in a film annotation character area. Specifies the maximum number of Kanji patient name characters to be printed out. * If the employed setting is greater than the default value (10), the other information may not fit in a film annotation character area. Specifies whether the patient name should be right-aligned or leftaligned. Specifies the maximum number of 1-byte exposure menu name characters to be printed out. * If the employed setting is greater than the default value (20), the other information may not fit in a film annotation character area. Specifies the maximum number of Kanji exposure menu name characters to be printed out. * If the employed setting is greater than the default value (16), the other information may not fit in a film annotation character area. Specifies whether the exposure menu name should be right-aligned or left-aligned. Specifies whether the automatic editing function for the format definition file should be enabled or disabled.

Remarks

13-10

13-11 13-12

Setting for right/left justification 0 : Left (left alignment) of patient names. 1 : Right (right alignment) Setting for the maximum value 0 to 64 ( 20) of en-size character numbers for the exposure menu names to be film-output. Setting for the maximum value 0 to 64 ( 16) of em-size character numbers for the exposure menu names to be film-output. Setting for right/left justification 0 : Left (left alignment) of the exposure menu names. 1 : Right (right alignment) Activation of automatic generation function for film annotation character format. Yes No

13-13

13-14 13-15

: Default setting, *: Note

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

MU-40

MU-41
Setting for output function
Number
14-1

Setup item name

Option

Description
Specifies whether or not to perform a retry after the occurrence of an output abnormality. At print : Acquires the status at the time of printing. Polling : Acquires the status periodically. Specifies whether or not to be essential to DVD burning for the image storage. Yes : Essential No : Not essential

Remarks

Whether or not retry has been Yes : Performs a retry. executed after an abnormal No : Performs no retry. output was made. Status acquisition timing of DICOM printer Arbitrary setting of DVD burning for storage 0 : At print 1 : Polling Yes No

14-2 14-3

14-5

Whether annotation information will be embedded in the images for film output.

Yes No

Specifies whether or not to embed annotation information in the images Setting is also possible with the user for film output. utility. Yes : Annotation information will be embedded in the images for film output. No : Annotation information will not be embedded in the images for film output. Specifies whether or not to embed annotation information in the images for general-purpose file output. Yes : Annotation information will be embedded in the images for general-purpose file output. No : An annotation information will not be embedded in the images for general-purpose file output. Setting is also possible with the user utility.

14-6

Whether annotation information will be embedded in the images for generalpurpose file output.

Yes No

: Default setting, *: Note

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-41

MU-42
Operation (low frequency) setting
Number
15-1 15-2 15-3 15-4 15-5 15-6 15-7 15-8 15-9 15-10 15-11 15-12

Setup item name


The maximum registration number of patient information The maximum registration number of study information Status acquisition timing of DICOM printer Timeout occurring prior to study termination Maximum number of markers Primary threshold warning system capacity Secondary threshold warning system capacity Warning threshold on system capacity Primary threshold warning database capacity Secondary threshold warning database capacity Warning threshold on database capacity Minimum remaining capacity of local HDD

Option
10000 to 200000 ( 200000). 10000 to 60000 ( 60000). 1 to 16 ( 6) 5 to 600 ( 5) 0 to 128 ( 50) 36 to 65 ( 50) 16 to 35 ( 30) 10 to 15 ( 10) 151 to 300 ( 200) 51 to 150 ( 100) 10 to 50 ( 30) 1024 to 65535 ( 5120)

Description
Specifies the maximum number of patients to be registered (patient information FIFO maximum count). Specifies the maximum number of studies (study information FIFO maximum count).

Remarks

Primary threshold warning system capacity (the indicator changes from blue to yellow). (Unit : GB) Secondary threshold warning system capacity (the indicator changes from yellow to red). (Unit : GB) Warning threshold on system capacity (an error message is displayed). (Unit : GB) Primary threshold warning database capacity (an error is displayed in the indicator at the time of startup). (Unit : MB) Secondary threshold warning database capacity (an error is displayed in the indicator at the time of startup). (Unit : MB) Warning threshold on database capacity (an error message is displayed). (Unit : MB) Threshold for automatic transfer or deletion of the study data. (Unit : MB)

: Default setting, *: Note

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-42

MU-43
Setting for analysis
Number
19-1

Setup item name


Log acquisition of DICOMPrintSCU communication Log acquisition of FRUPMain control communication Log acquisition of FRUP connection watch Log acquisition of FRUP image connection Trace log acquisition when image is output Log acquisition of DICOM verification SCU Log acquisition of DICOM storage SCU Collect image data for maintenance logs (For the number of studies) Arbitrary settings for acquisition of DICOM storage SCP log Retrieve the log in MWM function 0 : No 1 : Yes 2 : Yes (details). 0 : No 1 : Yes 0 : No 1 : Yes 0 : No 1 : Yes 0 : No 1 : Yes 0 : No 1 : Yes 2 : Yes (details). 0 : No 1 : Yes 2 : Yes (details).

Option
DICOM print log acquisition.

Description

Remarks

19-2 19-3 19-4 19-5 19-6

Log acquisition. Log acquisition. Log acquisition. Output process trace log acquisition. DICOM verification log acquisition.

19-7

DICOM storage SCU log acquisition.

19-8

0 to 60000 ( 2000).

The number of studies to be collected when deleting personal information (all studies are collected when no personal data is deleted.) DICIOM storage SCP log acquisition (Not used.)

19-9

0 : No 1 : Yes 2 : Yes (details). 0 : No 1 : Yes 2 : Yes (details).

19-10

DICOM MWM log acquisition.

: Default setting, *: Note

Settings for endoscopic image import


Number
20-1

Setup item name


Support availability on endoscopic image import and the receiving system Receiving folder for endoscopic image import 0 : None 1 : M-Receive 2 : FTP

Option

Description
Endoscope image acquisition support and reception method.

Remarks
This option item is not used.

20-2

(Max. 255 characters)

Endoscope image acquisition reception folder name.

This option item is not used.

: Default setting, *: Note

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-43

MU-44
Electrocardiographic data import settings
Number
21-1

Setup item name


Data structure linked with the electrocardiograph(The data varies from maker to maker.) 1: Fukuda

Option

Description

Remarks
This option item is not used.

21-2

Folder in which on-line C:\FUKUDA\ECG electrocardiographic data obtained from Fukuda Denshi electrocardiograph is stored in the form of folder path. Folder dedicated for registration/management in which electrocardiographic data for display obtained from Fukuda Denshi electrocardiograph is stored C:\FUKUDA\FEV\REF

This option item is not used.

21-3

This option item is not used.

21-4

Folder in which Fukuda C:\FUKUDA\UP Denshi electrocardiograph data that has been modified is temporarily stored for update at a later time Application path to link electrocardiogram C:\Program Files\FUKUDA\FEV\FEV-Fuji. EXE

This option item is not used.

21-5

This option item is not used.

: Default setting, *: Note

PDI output function settings


Number
22-4

Setup item name


PDI write mode

Option
0 : Test writing 1 : Test writing + final writing 2 : Final writing Yes: Compression No: No compression

Description

Remarks

22-5

Compression of images (PDI)

Yes: JPEG Lossless [1.2.840.10008.1.2.4.70] No: Explicit VR Little Endian (LEE) [1.2.840.10008.1.2.1]

JPEG Lossless [1.2.840.10008.1.2.4.70]: This option can be chosen for CR images, but not for CT images. Explicit VR Little Endian (LEE) [1.2.840.10008.1.2.1]: This option can be chosen for both CR and CT images.

: Default setting, *: Note

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-44

MU-45
Free Layout Setting
Number
24-1

Setup item name


Presence/Absence of Patient ID display Yes No

Option

Description
Presence/Absence of Patient ID display

Remarks

: Default setting, *: Note

Setting for DICOM-MWM


Number
25-1

Setup item name


Whether support is provided or not to linkage with the MWM Server. Yes No

Option

Description
Whether support is provided or not to linkage with the MWM Server.

Remarks

25-2

Preferential destination for 0 : Local DB patient information search, in 1 : MWM the linkage with MWM Server.

Priority destination for patient information search

: Default setting, *: Note

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-45

MU-46
Film annotation character areas 1 and 2
This section describes the display, position, and rotation of film annotation character areas 1 and 2, which can be defined by setup items No.12-12 and 12-14 to 12-31. If an image is printed on a 14"17" film as set by the default, the film annotation characters are displayed at both the upper right and left of the image. Areas where those characters are displayed are the film annotation character areas. The upper-left area is area 1 and that at the upper right is area 2.
Film annotation character area 1

Positional and rotational movement of the film annotation character areas


Use setup items No.12-14 to 12-31 Film character area position and rotation... to specify the position and rotation of the film annotation character areas. The general idea about the film annotation character area position and rotation is indicated below.
Position 0 Position 1

Not rotated. 90 rotated (counterclockwise). One-frame film area One-frame film area

Film annotation character area 2 Output print image (*Default setting)

Position 2

Position 3

Definition of positional movement


F0000010.EPS

Definition of rotational movement

F0000009.EPS

Whether to display the film annotation character areas


Use setup item No.12-12 Whether or not film character area display is available when 1824-Single is formatted half-size Film 1417-Single/4on1, 1843-LR/2on1/4on1, 810-4on1 format, and 810 film size. to specify whether or not to display film annotation character areas 1 and 2. 0: None Does not generate a film output. 1: Only area 1 Displays film annotation character area 1 only. 2: Only area 2 Displays film annotation character area 2 only. 3: Both (default) Displays both film annotation character areas.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-46

MU-47
Output film determination sequence
When Yes is chosen for setup item No.12-33 Setting for validity/invalidity of reduced output onto an 810film, the output film size is determined in the following sequence:
Film combination
14"17" 8"10"

Details of [dialog setup]


Procedure for 12-9 Setting of menu code in which scale is not displayed (effective when setting is such that image frame is added).
Double-clicking the setup value in the No. 12-9 column will open the following dialog.

Determination sequence
1. When the 3543 (cm) or 3535 (cm), high pixel density, Single format is used, the image will be printed onto 14"17" film at a magnification of 100%. 2. When a Single format other than indicated above is used, the image will be printed onto 8"10" film. 3. 4on1 and 3on1 format images are printed on 14"17" films. 4. In situations other than above, images are printed on 14"17" films in the 2636cm film output format. 1. When the Single format is used, the image will be printed onto 8"10" film. 2. In situations other than above, the image will be printed onto 2636cm film. 1. When the Single format is used, the 10"12" and 2430cm images will be printed onto 10"12" film. 2. When a Single format other than indicated above is used, the image will be printed onto 8"10" film. 3. In situations other than above, there are no applicable films. 1. When 3535 (cm), high pixel density, Single format is used, the image will be printed onto 14"14" film at a magnification of 100%. 2. When a Single format other than indicated above is used, the image will be printed onto 8"10" film. 3. In situations other than above, there is no applicable film. 1. When the Single format is used, the image will be printed onto 8"10" film. 2. In situations other than above, there is no applicable film.

I.

2636cm

8"10"

2636cm

8"10"

II.

8"10"

14"14"

III.

IV.
MU000048.EPS

I.

8"10"

Choose Displaying a scale on all images when providing a scale for all films. Choose Displaying no scale on all images when providing no scale for all films. Choose Selecting an undisplayed MPM code when ensuring that images having a particular MPM code are not provided with a scale. II. Enter the images MPM code on the keyboard or select it from the pull-down menu. Be sure to set up if Selecting an undisplayed MPM code is selected in step I. above. Specifying using a wild card is also possible, such as ?0?? (? is an arbitrary one-digit alphanumeric from 0 to F.) III. Click to cancel the setup data to be saved. IV. Click if data set up in I. and II. above are correct. The system returns to the previous window and any of the following will be displayed in the Value column. : Does not provide a scale. ???? : Provides a scale for all images. (Blank) Four-digit number : MPM code of an image not added with reading scale.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-47

MU-48
Setup procedure for 12-14 to 12-25 Film character area position and rotation...
Double-clicking the setup value in the column of Nos. 12-14 to 25 will open the following dialog.
VI. Click if data set up in I. to IV. above are correct. The system returns to the previous window and a four-digit number will be displayed in the Value column. The meaning of such four-digit number is as follows.

0031
90o image rotation of film annotation character area 2 (0: Not rotated, 1: Rotated) Position of film annotation character area 2 (0: Upper left, 1: Upper right, 2: Lower left, 3: Lower right) 90o image rotation of film annotation character area 1 (0: Not rotated,1: Rotated)

I.

II.

Position of film annotation character a rea 1 (0: Upper left, 1: Upper right, 2: Lower left, 3: Lower right)
F0000014.EPS

III.

IV.

V.

VI.

MU000049.EPS

I. Specifies the film annotation character area 1 display position. II. Specifies the 90 image rotation (counterclockwise) of film annotation character area 1. III. Specifies the film annotation character area 2 display position. IV. Specifies the 90 image rotation (counterclockwise) of film annotation character area 2. For details of the film annotation character area, see Film annotation character areas 1 and 2. V. Click to cancel the setup data to be saved.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-48

MU-49
Setup procedure for 12-26 to 12-31 Film character area position and rotation (user definition X)
Double-clicking the setup value in the column of Nos. 12-26 to 31 will open the following dialog.
I.

VII. Click to apply the settings entered in steps I. to V. The system then returns to the previous window and character strings appear in the Setup value fields to represent the settings.
Definition of image position or rotation MPM code (a maximum of 8 codes can be displayed.)

0031 : 0000 0004 0009 000C 000E 000B 0002 0008


90o image rotation of film annotation character area 2 (0: Not rotated, 1: Rotated) Position of film annotation character area 2 (0: Upper left, 1: Upper right, 2: Lower left, 3: Lower right) 90o image rotation of film annotation character area 1 (0: Not rotated,1: Rotated) Position of film annotation character a rea 1 (0: Upper left, 1: Upper right, 2: Lower left, 3: Lower right)

II.

III.

F0000015.ai

IV.

V.

VI.

MU000050.EPS

VII.

I. II. III. IV. V.

From the pull-down menu, select the MPM code for the image whose film annotation character area is to be changed. You cannot specify the MPM code from the keyboard or through the use of a wildcard character. Specify the film annotation character area 1 display position. Specify the 90 image rotation (counterclockwise) of film annotation character area 1. Specify the film annotation character area 2 display position. Specify the 90 image rotation (counterclockwise) of film annotation character area 2. For details of the film annotation character area, see Film annotation character areas 1 and 2.

VI. Click to cancel the setup data to be saved.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-49

MU-50 6.2 Connected Equipment


Perform setup for each of the devices to be connected to the CR-IR 391CL. The contents of the Setting connection devices window are classified under the Server (this equipment) and Image Reader categories. The Client equipment, Film printer and DICOM Storage Device categories do not appear in the window if the associated options are not installed.

6.2.1 Server Equipment Settings


Perform setup for the CR-IR 391CL server.

Settings accessible from the Server equipment settings window


Name
Equipment name

Description

Setting

Equipment name that Input method: Text input. identifies the equipment. Acceptable input characters: 1- and 2-byte characters. Maximum number of characters: 16 characters. Host name assigned to the equipment. IP address assigned to the equipment. Specifies whether or not to display the software keyboard in the patient/ study information input windows. This is merely displayed. The information acquired from the OS is displayed. This is merely displayed. The information acquired from the OS is displayed. Input method: Single selection. ON: Displays the software keyboard. OFF: Does not display the software keyboard. See under 6.2.2 Monitor Settings. Input method: Text input or spin button. Acceptable input characters: 1-byte numerals. Value range: 1 to 999. See under 6.2.2 Monitor Settings.

Host name

IP Address

Software keyboard

Monitor settings

Monitor model Monitor model name. Magnified Display (%) Width of one pixel of the employed monitor.

MU000053.ai

DICOM setting Disk drive settings

DICOM device setting. Settings for the image storage disk drive.

See under 6.2.3 DICOM Settings. See under 6.2.4 Disk Drive Settings.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-50

MU-51
Setup procedure

5. 6. 7. 8.

Set up the monitor.


See under 6.2.2 Monitor Settings.

1. 2. 3. 4.

Start the Service Utility.


The Service Utility top window opens.

Perform DICOM setup.


See under 6.2.3 DICOM Settings.

Click [Connected equipment].


The Setting connection devices window opens.

Set up the disk drive.


See under 6.2.4 Disk Drive Settings.

Click [Server (this equipment)].


The Server equipment settings window opens.

Click [OK].
The system returns to the Service Utility top window.

Perform the following setup steps:

I.

II.

MU000004.ai

I. Enter the equipment name. II. If you use the software keyboard in the patient/study information input windows, put a checkmark in the Use check box ( ).

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-51

MU-52
6.2.2 Monitor Settings
Select a monitor model and a gradation correction file (LUT file) that matches the selected monitor model.

5.

Select a registered monitor model, gradation correction file, and magnified display (%) of the reference image.
REFERENCE

1. 2. 3. 4.

Start the Service Utility.


The Service Utility top window opens.

Clicking [Update] updates the displayed monitor model list.

Click [Connected equipment].


The Setting connection devices window opens.

MU000005.EPS

Click [Server (this equipment)].


The Server equipment settings window opens.

6.

Click [OK].
The system returns to the Server equipment settings window.

NOTE
The monitor settings are automatically entered. Do not change the Magnified display (%) of the reference image here although it can be changed.

Click [Selection].

IMPORTANT
For a locally procured LCD monitor, be sure to perform the procedure below: I. Insert an FD where the LUT file is stored into the FD drive. II. Click Update on the Monitor model selection window. III. Select an LUT for the added model and click [OK].
The Monitor model selection window opens.

7.

If the Magnified display (%) of the reference image needs to be fine tuned, click the or for adjustment purposes.

NOTE
Selecting a Monitor model automatically enters a Magnified display (%) of the reference image value. Do not change the value under normal conditions. If you change the value, you have to make sure that the image displayed at a magnification of 100% is of the actual size.

8.

Click [OK].
The system returns to the Service Utility top window.

MCApp13001.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-52

MU-53
6.2.3 DICOM Settings
This section describes the procedure for DICOM device setup. Perform local equipment setup concerning the DVD drive, DICOM Print, and DICOM Storage.

Setup procedure

1. 2. 3. 4.

Start the Service Utility.


The Service Utility top window opens.

Settings accessible from the Set up DICOM window


Name
Media Storage setting AE Name (I.) Name identified when the DICOM protocol is used. Use MEDIA. Maximum pixel density size for an image stored on the management disk drive. Method for compressing the image to be stored on the management disk drive. Input method: Text input. Maximum number of characters: 16 characters. Input method: Single selection. ST HQ Input method: Single selection. Image data compressed Image data not compressed

Click [Connected equipment].


The Setting connection devices window opens.

Description

Setting

Click [Server (this equipment)].


The Server equipment settings window opens.

Maximum pixel density size for a stored image (II.) Whether or not to specify data compression for stored images (III.) Setting multi-byte characters (IV.)

Click [DICOM setting].


The Set up DICOM window opens.

Specifies whether any Input method: Single selection. incidental information in multi- ON: Stores the image information. byte characters should be OFF: Does not store the image stored on media. information. Name identified when the DICOM protocol is used. Use FCR-CSL. Input method: Text input. Maximum number of characters: 16 characters.

Print SCU setting AE Name (V.)

Timeout Value (VI.) Command level timeout value. Input method: Text input. Acceptable input characters: 1-byte numerals. Value range: 1 to 3600. Presentation Context (VII.) Sets the currently used abstract syntaxes. Input method: Multiple selections. BasicGrayscalePrint: Nonselectable. Yes at all times. Verification: Yes/No Input method: Text input. Maximum number of characters: 16 characters.

Settings for Storage SCU AE Name (VIII.) Name identified when the DICOM protocol is used. Use FCR-CSL.

Timeout Value (IX.) Command level timeout value. Input method: Text input. Acceptable input characters: 1-byte numerals. Value range: 1 to 3600.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-53

MU-54
5.
Perform the following setup steps:
Media storage setup I. Enter the AE name (e.g., MEDIA).

NOTES
I. II. III. IV.

The acceptable input characters are 1-byte alphanumeric characters. The maximum number of character is 16.
II. Select a maximum pixel density size for the image to be stored on the management disk drive.
Setting
ST HQ : Default Standard density. High density.

Description

REFERENCE
V. VI. VII.

Selecting HQ reduces the number of images that can be recorded on a DVD.


For the number of images that can be stored when the ST, HQ, compressed, or uncompressed option is selected, see under 1.6 Image Storage Performance of Product Specifications.

III. Select a method for compressing the image to be stored on the management disk drive.
Setting
Image data compressed
MU060207.ai

Description
Compresses the image (lossless).

Image data not compressed Does not compress the image.

: Default

REFERENCE
Print SCU setting and Settings for Storage SCU do not appear in the window if these options are not installed.

REFERENCE
Selecting Image data not compressed reduces the number of images that can be recorded on a DVD.
For the number of images that can be stored when the ST, HQ, compressed, or uncompressed option is selected, see under 1.6 Image Storage Performance of Product Specifications.

IV. When storing Kanji or other 2-byte character information, put a checkmark ( ).

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-54

MU-55
Print SCU setting (option) Select the [Print SCU setting] tab and perform the following setup steps:
V. Enter the AE name (FCR-CSL).

Settings for Storage SCU (option) Select the [Settings for Storage SCU] tab and perform the following setup steps:

NOTES
The acceptable input characters are 1-byte alphanumeric characters. The maximum number of character is 16.
VI. Specify the timeout value (300) between DICOM messages by entering text or by clicking the or . VII. Put a checkmark in the check boxes for the currently used abstract syntaxes ( ).

NOTE
The check box for BasicGrayscalePrint is checked at all times.

REFERENCE
Verification is a service class for verifying the connection between DICOM devices. When verifying the connection, it is necessary to check Verification. For details on connection verification, see under 7.3 Connection Check.
VIII. Enter the AE name (FCR-CSL).

VIII. IX.
MU060206.ai

IX. Specify the timeout value (300) between DICOM messages by entering text or by clicking the or .

6. 7. 8.

Click [OK].
The system returns to the Server equipment settings window.

Click [OK].
The system returns to the Setting connection devices window.

Click [Back].
The system returns to the Service Utility top window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-55

MU-56
6.2.4 Disk Drive Settings
Perform disk drive setup.

Setup procedure

1.
Description
Specifies whether or not to use the disk drive for server management. * Essential Name for disk drive identification.

Start the Service Utility.


The Service Utility top window opens.

Settings accessible from the Disk drive settings window


Name
Use

Setting
Input method: Single selection. ON at all times.

2. 3. 4.

Click [Connected equipment].


The Setting connection devices window opens.

Setting a Disk Drive for Server Management

Click [Server (this equipment)].


The Server equipment settings window opens.

Drive name

Input method: Text input. Acceptable input characters: 1- and 2-byte characters. Maximum number of characters: 16 characters. Input method: Specify the path from the file browse dialog box. Input method: Single selection. Not specified (no formatting) Dedicated application (UDF 1.5/UDF 2.0) OS (FAT32)

Click [Disk drive settings].


The Disk drive settings window opens.

Drive path

Path to the drive.

Disk format application Specifies whether or not to format an unformatted medium type when it is inserted. Selects a format type. * Select the Dedicated application. Dedicated format application path Use File path for storing a media formatting application. Specifies whether or not to use the disk drive for viewing the server. Name for disk drive identification.

Input method: Specify the path from the file browse dialog box. Input method: Single selection. ON: Uses the drive. OFF: Does not use the drive. Input method: Text input. Acceptable input characters: 1- and 2-byte characters. Maximum number of characters: 16 characters. Input method: Specify the path from the file browse dialog box.

Setting a Disk Drive for Viewing the Server

Drive name

Drive path

Path to the drive.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-56

MU-57
5.
Perform the following setup steps:
I. Enter the drive name (e.g., DVD) of the management disk drive.

NOTES
Both the 1- and 2-byte characters can be entered. The maximum number of characters is 16.
I. II. III. IV.

II. Specify the DVD drive path. Click [Browse] to open the Browse for Folder window. Specify the connected DVD drive, and then click [OK]. III. Select Dedicated application as the type of DVD drive media formatting application.
Setting
Not specified OS

Description
Does not provide formatting. Use an OS function to provide formatting.

Dedicated application Provides formatting with the dedicated application.

: Default

IV. Specify the Dedicated application format path. Input C:\Program Files\FujiFilm\Hobbit\System\FFUdfFmtToolForVista.exerD.

NOTE
Input D to the end of the path ( represents a space and D represents a DVD drive path).

MU000529.ai MU000007.ai

NOTE
When specifying the Drive path for the management disk drive, specify only a DVD drive that is directly connected to the server. No image can be stored on a DVD drive that is shared by a network.

6. 7. 8.

Click [OK].
The system returns to the Server equipment settings window.

Click [OK].
The system returns to the Setting connection devices window.

Click [Back].
The system returns to the Service Utility top window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-57

MU-58
6.2.5 Image Reader Settings
Perform image reader setup.

Setup procedure

1. 2. 3. 4.

Start the Service Utility.


The Service Utility top window opens.

Settings accessible from the Settings necessary for the Image Reader window
Name
Equipment name

Click [Connected equipment].


The Setting connection devices window opens.

Description
Displayed equipment name. This name is displayed as the Equipment name of Image Reader in the indicator window. The default is Image Reader. Host name assigned to the equipment. The default is RU0. IP address assigned to the equipment. The default is 172.16.1.10.

Setting
Input method: Text input. Acceptable input characters: 1- and 2-byte characters. Maximum number of characters: 16 characters. Input method: Text input. Acceptable input characters: 1-byte characters (A-Z and a-z), 1-byte numerals, and hyphen (-). Input method: Text input. Acceptable input characters: 1-byte numerals and period (.). The IP address consists of four elements. The value of each element ranges from 0 to 255. Use a period to delimit each element.

Click [Image Reader].


The Settings necessary for the Image Reader window opens.

Host name

Perform the following setup steps:

IP Address

I. II. III. IV.

Check the box to use Patient information display

Specifies whether or not to Input method: Single selection. support the patient information ON : Displays patient information. display on the Image Reader OFF : Does not display patient operation panel. information.
MU060205.ai

I.

Enter the equipment name.

II. Enter the host name that is assigned to the equipment.

NOTE
Acceptable input characters are 1-byte characters (A-Z and a-z), 1-byte numerals, and hyphen (-).
III. Enter the IP address that is assigned to the equipment.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-58

MU-59
IV. When displaying patient information on the Image Readers operation panel, put a checkmark in the check box ( ).

NOTE
To have the patient information be displayed, the relevant setting must be turned ON also on the RU side. In case of 391RU, be sure to set to OFF. For details of the procedure to use, see Appendix 4: Setting the RU-Config in MC: Checks, Replacement and Adjustment of Parts.

5. 6.

Click [OK].
The system returns to the Setting connection devices window.

Click [Back].
The system returns to the Service Utility top window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-59

MU-60
6.2.6 Film Printer Settings (option)
When connecting the optional film printer, perform the setup procedure described below.
Name
Detailed settings for film printers Supported abstract syntaxes Abstract syntaxes supported by the film printer. Input method: Multiple selections. BasicGrayscalePrint Verification Input method: Multiple selections. 8IN10IN 10IN12IN 10IN14IN 14IN14IN 14IN17IN Input method: Single selection. HQ ST

Description

Setting

Settings accessible from the Settings necessary for the film printer window
Name
Equipment name

Film size available for Film sizes supported by the printout film printer.

Description
Displayed equipment name. This name is displayed as the Equipment name of Printer in the indicator window and as the Destination for Output status. Example: DRYPIX PRIMA. Host name assigned to the equipment. Example: fujiprinter. IP address assigned to the equipment. Example: 172.16.1.30.

Setting
Input method: Text input. Acceptable input characters: 1- and 2-byte characters. Maximum number of characters: 16 characters.

Transferable image sizes Destination for film output

Pixel density of an image size that is transferred at the time of printing.

Host name

Input method: Text input. Acceptable input characters: 1-byte characters (A-Z and a-z), 1-byte numerals, and hyphen (-). Input method: Text input. Acceptable input characters: 1-byte numerals and period (.). The IP address consists of four elements. The value of each element ranges from 0 to 255. Use a period to delimit each element. Input method: Text input. Acceptable input characters: (The DICOM VR=AE condition is complied with.) ISO 646 (1990) basic G0 set excluding the following control characters: LF, FF, CR, and ESC. Maximum number of characters: 16 characters. Input method: Text input. Acceptable input characters: 1-byte numerals.

Information that is set as Film Input method: Single selection. Destination (2000,0040). Not specified MAGAZINE PROCESSOR BIN_I This setting is valid only when BIN_I is selected as the film output destination. Information for bin number assignment. This setting is valid only when BIN_I is selected as the film output destination. Bin number for outputting the film that could not be identified by the Bin number identification information setting. Input method: Single selection. MPM code Anatomical region Not specified Input method: Text input. Acceptable input characters: 1-byte numerals. Value range: 1 to 100.

IP Address

Bin number identification information

Default bin number

DICOM AE name

Name identified when the DICOM protocol is used. Example: DRYPIX.

Image size specification function for printers A printer generating 10bit image printout Film type

Specifies whether Requested Input method: Single selection. Image Size (2020,0030) is ON : Supported. supported by the film printer. OFF : Unsupported. Specifies whether the film Input method: Single selection. printer can handle 10-bit data. ON : Supported. OFF : Unsupported. Employed film type. Input method: Single selection. Not specified CLEAR FILM BLUE FILM PAPER Input method: Single selection. Dmax: 3.0 Dmax: 3.6

Port number

Number of the port used by film printer. Example: 17238.

Maximum film density Maximum density of the film. (Dmax)


020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-60

MU-61
Name
Dealing with an image not accommodated within the printers image area

Description
Process to be performed when the image is not accommodated within the drawing area that is defined by Requested Decimate/Crop Behavior (2020,0040). Information to be set as Magnification Type (2010,0060).

Setting
Input method: Single selection. DECIMATE CROP FAIL Not specified Input method: Single selection. REPLICATE BILINEAR CUBIC NONE Input method: Text input. Acceptable input characters: 1-byte characters (A-Z and a-z), 1-byte numerals, 1-byte space, and 1-byte underscore (_). Maximum number of characters: 16 characters.

Setup procedure

1. 2. 3. 4.

Start the Service Utility.


The Service Utility top window opens.

Click [Connected equipment].


The Setting connection devices window opens.

How to magnify an image size

Click [Film printer].


The Settings necessary for the film printer window opens.

Smoothening type This setting is valid only when CUBIC is selected as the image magnification method. Only the following settings are selectable: SMOOTH SHARP MEDIUM

Click [Add].
The Changing film printers window opens.

* The examples represent a situation where the DRYPIX PRIMA is used.

MU000054.ai

5. 6.

Enter the film printer name (e.g., DRYPIX3000) in the Equipment name field. Enter the film printer host name (e.g., fujiprinter) in the Host name field.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-61

MU-62
7. 8. 9.
Enter the film printer IP address (e.g., 172.16.1.30) in the IP Address field. Enter the film printer AE name (e.g., DRYPIX) in the DICOM AE name field. Enter the film printer port number (e.g., 17238) in the Port number field.

11. Click [Printer model selection].


The Selecting default settings specific to film printer model window opens.

10. Click [Detailed settings].


The Detailed settings for film printers window opens.
MU000602.ai

12. Select a model and then click [OK].


The system returns to the Detailed settings for film printers window. The settings for the selected model are set as the default ones.

13. Put a checkmark in both the BasicGrayscalePrint and Verification


check boxes under Supported abstract syntaxes ( ).

REFERENCE
Verification is a service class for verifying the connection between DICOM devices. When verifying the connection, it is necessary to check Verification. For details on connection verification, see under 7.3 Connection Check.

14. In the

menu, specify the film sizes ).

that can be printed out. Put a checkmark in a check box (


MU000601.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-62

MU-63
15. Click the downward arrow mark (
Setting
SH HQ : Default

) for Transferable image sizes, and then select a reception image size.
Description
Reception image size maximum density (ultra-high density). Reception image size maximum density (high density).

III. Click [Setting details of bins]. The Setting details of bins window opens.

16. Click the downward arrow mark (


Setting
Not specified MAGAZINE BIN_I

) for Destination for film output, and then select a film output destination.
Description
Complies with the printer setting. Delivers the output to a magazine type printer. Delivers the output to the ejection tray on the top of the printer. Delivers the output to the sorter bin.
IN000515.EPS

PROCESSOR : Default

IV. In accordance with the selection made under Bin number identification information, double-click the Key field and then enter a key. If MPM code is selected under Bin number identification information, enter an MPM code (e.g., 0200). If Anatomical region is selected, enter an anatomical region name (e.g., CHEST).

17. If BIN_1 (sorter setting) is selected as the Destination for film


output, perform the following setup steps:
I. Click the downward arrow mark ( ) for Bin number identification information, and then specify the bin number identification information.
Setting
MPM code Anatomical region Not specified

Description
Identifies the output bin by MPM code. Identifies the output bin by anatomical region. Complies with the printer setting.
IN000516.EPS

: Default

II. Click the downward arrow mark ( specify the default bin number.

) for Default bin number and then

V. Double-click the Bin number field, and then enter a bin number.

18. If the Image size specification function for printers is supported, put
a checkmark in the Supported check box under ( ).

REFERENCE
In the default bin number field, specify a default bin that is used for film output when no collation value (collation based on the identification information) is complied with. For bin numbers, see the printer service manual.

(When the DRYPIX Series is used, be sure to check the check box because the function is supported.)

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-63

MU-64
19. If the printer supports 10-bit image prints, put a checkmark in the
Supported check box under ( ). (When the DRYPIX Series is used, be sure to check the check box because the 10-bit image prints are supported.)

22. Click the downward arrow mark (

) for Dealing with an image not accommodated within the printers image area, and then select the process to be performed for an image that is not accommodated within the printers image area.
Setting
DECIMATE CROP Decimates. Crops. Complies with the printer setting. Does not generate an output because the image is not accommodated within a recordable image frame.

Description

20. Click the downward arrow mark (


film type.

) for Film type and then select a


Description

Not specified FAIL Complies with the printer setting. Selects clear film. Selects blue film. Selects a paper printout (this option can be selected when a DICOM printer that can generate a paper output is connected).

Setting
Not specified CLEAR FILM

: Default

BLUE FILM PAPER

23. Click the downward arrow mark (


Setting
REPLICATE BILINEAR NONE

) for How to magnify an image size, and then select an image magnification method.
Description
Provides interpolation by replicating a most similar neighboring color when creating a new pixel for magnification. Provides bilinear interpolation when magnifying the image. Provides bicubic interpolation when magnifying the image. Does not magnify or reduce the image.

: Default * The DRYPIX Series cannot generate paper printouts.

21. Click the downward arrow mark (


Setting
3.0 3.6

) for Maximum film density (Dmax) and then specify the maximum film density.
Description
Issues an output request to the printer with the maximum density set at 3.0. Issues an output request to the printer with the maximum density set at 3.6.

CUBIC : Default

REFERENCE
Bilinear interpolation When a new pixel is to be generated for magnification, its color is created by averaging the colors of four (linear) neighboring pixels (upper, lower, right, and left pixels). Bicubic interpolation When a new pixel is to be generated for magnification, its color is created by averaging the colors of eight (cubic) neighboring pixels (upper, lower, right, and left pixels and pixels at four corners).

: Default

NOTE
The printer setting should be basically complied with. This setup step need not be performed for the DRYPIX Series. For details, see the printer service manual.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-64

MU-65
24. If CUBIC was selected in Step 23 above as the image magnification
method, enter a smoothening type in the Smoothening type field. (If an image magnification method other than CUBIC was selected in Step 23, it is not allowed to enter a smoothening type because the Smoothening type field does not become active.)

6.2.7 Storage Setup for DICOM Storage Device (option)


When the optional DICOM storage device is to be connected, perform setup concerning the other equipment to which images are to be transmitted.

NOTE
For the DRYPIX Series, only the SMOOTH, MEDIUM, and SHARP options are selectable (SMOOTH is selected by the default).

Settings accessible from the DICOM storage setup window


Name
Equipment name (I.)

Description
Equipment name that permits the user to identify the equipment.

Setting
Input method: Text input. Maximum number of characters: 16 characters. Acceptable input characters: 1-byte and 2-byte characters. Input method: Text input. Maximum number of characters: 255 characters. Acceptable input characters: 1-byte characters (A-Z and a-z), 1-byte numerals, and hyphen (-). Input method: Text input. Acceptable input characters: 1-byte numerals and period (.). The IP address consists of four elements. The value of each element ranges from 0 to 255. Use a period to delimit each element. Input method: Text input. Acceptable input characters: (The DICOM VR=AE condition is complied with.) ISO 646 (1990) basic G0 set excluding the following control characters: LF, FF, CR, and ESC. (Maximum number of characters: 16 characters.)

DICOM storage device settings (addition/change)

25. Click [OK].


The system returns to the Adding film printers window.

26. Click [Add].


The system returns to the Setting the Film Printer window.

Host name (II.)

Host name assigned to the equipment.

27. Click [Finish].


The system returns to the Setting connection devices window.

IP address (III.)

IP address assigned to the equipment.

28. Click [Back].


The system returns to the Service Utility top window.
DICOM AE name (IV.)*1 This name is used for application entity identification when the DICOM protocol is used.

Port number (V.)

Port number of the connected Input method: Text input. DICOM storage device. Acceptable input characters: 1-byte numerals. Value range: 1 to 65535.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-65

MU-66
Name Description Setting
Nonselectable. ON at all times. Input method: Single selection. ON: Used. OFF: Not used. Input method: Single selection. Implicit VR Little Endian Explicit VR Little Endian JPEG Lossless Input method: Single selection. HQ ST Input method: Single selection. ON: Supported. OFF: Unsupported.

Setup procedure

Detailed settings for DICOM storage device Supported abstract CRImageStorage*2 syntax/transfer Verification syntax (I.) Specifies the CRImageStorage transfer syntax.*3 Receivable maximum pixel density size (II.) Setting multi-byte characters (III.) Specifies the maximum pixel density of an image that the DICOM storage device can receive. Specifies whether multi-byte characters are supported by the DICOM storage device.

1. 2. 3. 4. 5.

Start the Service Utility.


The Service Utility top window opens.

Click [Connected equipment].


The Setting connection devices window opens.

Click [DICOM Storage Device].


The DICOM Storage Settings window opens.

Click [Add].
The Addition of DICOM Storage Device window opens.

*1 Enter the SCP (ServiceClassProvider) AE title of CRImageStorage that is registered for the storage device. *2 Only CRImageStorage is supported as the storage output of the CR-IR 391CL. *3 Ensure that this setting complies with the setting for the other equipment.

Perform the following setup steps:

I. II. III. IV. V.

MU060202.ai

I. II. III. IV. V.


020-221-02E 01.08.2010 FM5563

In the [Equipment name] field, enter the equipment name to be displayed in the study list. In the [Host name] field, enter the host name of the storage device. In the [IP address] field, enter the IP address of the storage device. In the [DICOM AE name] field, enter the AE name of the storage device. In the [Port number] field, enter the port number for the storage device.

CR-IR 391CL Service Manual

MU-66

MU-67
6. 7.
Click [Detailed settings].
The Advanced settings for DICOM Storage Device window opens. III. In accordance with the other equipment, select HQ or ST as the [Receivable maximum pixel density size] (it is recommended that you choose HQ).
Setting
ST HQ : Default

Perform the following setup steps:

Description
Reception image size maximum density (standard density). Reception image size maximum density (high density).

I.

II.

IV. If the other equipment provides support to multi-byte characters for the Setting multi-byte characters box, checkmark it ( ).

8. 9.
III. IV.

Click [OK].
The system returns to the Addition of DICOM Storage Device window opens.

Click [Add].
The system returns to the DICOM Storage Settings window.

10. Verify that the registered device is added, and then click [Finish].
The system returns to the Setting connection devices window.

11. Click [Back].


The system returns to the Service Utility top window.
MU060203.ai

I.

Put a checkmark in both the CRImageStorage and Verification abstract syntax check boxes, which are located on the left-hand side under Supported abstract syntaxes_transfer syntaxes. II. In accordance with the other equipment, select a transfer syntax from the right-hand side field under Supported abstract syntaxes_transfer syntaxes.
Setting
ImplicitVRLittleEndian ExplicitVRLittleEndian JPEGLossless

INSTRUCTION
When you have performed settings for output devices in the Service Utility, be sure to perform Setting a destination for image output in the User Utility.

Description
VR* is included in the data elements (implicit VR*). The data consists of [tag/VR*/value length/value]. VR* is not included in the data elements (explicit VR*). The data consists of [tag/value length/value]. JPEG lossless compression

: Default VR* : Value Representation

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-67

MU-68 6.3 Linkage Function


Perform functional setup for linkage with another system. Linkage function is an optional setup item.

INSTRUCTION
When settings were performed for output devices in the Service Utility, be sure to perform Setting a destination for image output in the User Utility.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-68

MU-69 6.4 Film Annotation Characters


This function determines settings and formats for outputting annotation characters on film. Presented herein are the settings necessary for enabling the print output function.

Image size
The image size refers to the size of an image read on the Image Reader. Currently, the six image sizes, 14"17", 14"14", 10"12", 10"8", 2430cm and 1824cm, can be read on the CR-IR 391CL system. The 14"17" size image can also be called the 3543cm size image and the 14"14" size image, the 3535cm size image. Note that the 2430cm and 1824cm size images have basically no other denominations. As shown in the table below, the RU has RUs for both the inch-system IP and the metric-system IP. RU type Inch-system RU Metric-system RU Image sizes that can be read 14"17", 14"14", 10"12" and 10"8" 3543cm, 3535cm, 2030cm and 1824cm

Setup necessary when editing the film annotation character format


Describes various setup items for the film annotation character format.
For details of configurations used for the film annotation character format, see Settings accessible from the System settings window in 6.1 System.

Film annotation character setup (direct editing of FilmStrFmt)


Describes the film annotation character setup procedure defined for each FMT No.

Print formats
The print format is a layout where images are allotted on film for printout. The CR-IR 391CL system supports the following print formats : Single, 2on1 and 4on1
Film Image

Basic terms used for film output processing


Film size
The film size refers to the size of a film used for printout of an image. In the CR-IR 391CL system, the following five film sizes are supported: 3543cm, 3535cm, 2636cm, 10"12" and 2025cm The 3543cm size is called in some cases the 14"17" size, and similarly the 3535cm size is called the 14"14" size, the 2636cm size is called the 11"14" size, and the 20x25cm size is called the 10"8" size.

Single

2on1

4on1
F0000020.EPS

Single : One image is allotted on film. 2on1 : Two different images are allotted on film. 4on1 : Four different images are allotted on film.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-69

MU-70
2636cm, 3543cm/14"17", 8"10", 3535cm/14"14" and 10"12" film printout patterns [Reference]
Shown below are the film output patterns formed on 2636cm and 3543cm films. 2636cm film
4 4 4 5 4 5 4 5 4 5 2 1 4 5 5 5 4 5 4 5

2 1

2 1

2 6 6 1

2on1

2on1 (different sizes)


11 13 14 12

Pantomography 2on1

1843cm 2on1
11 12 13

Normal Single
11 13 14 12

11 13 14

12 14

1 2

Pantomography Single

1014inch Single (HQ)

1410inch Single (HQ)

1824cm 2on1 (100% size)

- Legends (items are according to the FMT Nos.) 1 : Patient information area 2 : Image processing parameter area 4 : Hospital name area 5 : Area for barcode, MPM code, etc. 6 : Patient information/image processing parameter area 11 : Reduced patient information area 12 : Reduced image processing parameter area 13 : Patient information area 14 : Image processing parameter area
F0000018.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-70

MU-71
3543cm film
11 13 14 12 11 13 14 12 11 12 12 4 5

2 1

3543cm/1417inch Single (HQ)

1843cm Single (HQ)

1843cm 2on1
11 12 11

3535cm/1414inch Single (HQ)


12

11 4 5 13 14

12

3543cm

1843

11

12

810inch
2 1

1414inch

Pantomography Single

4335cm/1714inch Single (HQ)

Different images 4on1 (example)

15

1530cm
2 1 15 5

1530cm
15

5 5 1

3535cm 1530cm 1530cm


15 6

1530cm
4 2

15

- Legends (items are according to the FMT Nos.) 1 : Patient information area 2 : Image processing parameter area 4 : Hospital name area 5 : Area for barcode, MPM code, etc. 6 : Patient/image processing parameter area 11 : Reduced patient information area 12 : Reduced image processing parameter area 13 : Patient information area 14 : Image processing parameter area 15 : Patient information/image processing parameter area

Pantomography 2on1

Different images 4on1 (example)

Different images 2on1 (example)

F0000019.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-71

MU-72
2025cm film
(A)
21

(B)
21

(C)
21 22

(D)
21 22

(E)
4 5

(F)
4 5

6 22 22 6

Pantomography 1824cm/810inch (ST) Single Vertical 810inch 1824cm/810inch, 2430cm/1012inch, 3535cm, 3543cm, 4343cm (ST/HQ) Single

1824cm Single

1824cm Single

For exposure menus other than mammography, images will be delivered in the (C) format. For right breast (DSR) (MPM code: 0317) mammographic exposure menus, images will be delivered in the (A) format. For other than right breast (DSR) (MPM code: 0317) mammographic exposure menus, images will be delivered in the (B) format.

- Legends (items are according to the FMT Nos.) 4 : Hospital name area 5 : Area for barcode, MPM code, etc. 6 : Patient information/image processing parameter area 21 : Patient information area 22 : Image processing parameter area

F0000021.EPS

3535cm film
11 13 14 12

- Legends (items are according to the FMT Nos.) 11 : Reduced patient information area 12 : Reduced image processing parameter area 13 : Patient information area 14 : Image processing parameter area

3535cm/1414inch Single

F0000022.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-72

MU-73
10"12" film
(A)
21 22

(B)
21 22

(C)
21 22

(D)
21 22

(E)
21

(F)
21

1012inch (ST/HQ) 1012inch (ST/HQ) 2430cm (ST/HQ)

2430cm (ST/HQ)

22

22

2430cm (ST/HQ)

2430cm (ST/HQ)

(G)
4 5

(H)
4 5

(I)
4 5

(J)

(K)
4 5

(L)
4 5

2 1 6 6

2 1 6 6

810inch, vertical 810inch (ST/HQ)

1824cm (ST/HQ) 502 810inch

810inch, vertical 810inch (ST/HQ)

1824cm (ST/HQ) 502 810inch

1824cm (ST/HQ)

1824cm (ST/HQ)

- Legends (items are according to the FMT Nos.) 1 : Patient information area 2 : Image processing parameter area 4 : Hospital name area 5 : Area for barcode, MPM code, etc. 6 : Patient information/image processing parameter area 21 : Patient information area 22 : Image processing parameter area

F0000035.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-73

MU-74
6.4.1 Film Annotation Character Setup (Direct Editing of FilmStrFmt)
This section describes the film annotation character setup procedure for FMT numbers, which are indicated under 2636cm, 3543cm/14"17", 8"10", 3535cm/14"14" and 10"12" film printout patterns [Reference] in 6.4 Film Annotation Characters. Film annotation character setup is performed by directly editing the contents of the FilmStrFmt file.

1. 2. 3. 4. 5.

Start the Service Utility mode.


The Service Utility top window opens.

Click [Film annotation characters].


The Setting film annotation character window opens.

Click [Editing a film annotation character definition file].


The FilmStrFmt file opens in Notepad.

IMPORTANT
When directly editing the contents of the FilmStrFmt file, be sure to select No as the configuration setting for Nos. 13 to 15 (Enable Auto Edit Function of the Film Annotation Character Format) in 6.1 System. If you directly edit the contents of the file while the setting is left ON, the Service Utility may restore the previous contents of the FilmStrFmt file. Therefore, when editing the FilmStrFmt file, follow the steps indicated below. 1. If it is necessary to edit the printer-related configuration settings with the Service Utility, do it first. 2. Complete an editing procedure with the Service Utility (only the configuration settings related to the printer), save the results, and then change the settings for Nos. 13 to 15 to No. 3. Finally, edit the contents of the FilmStrFmt file. Once the FilmStrFmt file has been subjected to direct editing, you should avoid using the Auto Film Annotation Character Format Generation Function. The setting for Nos. 13 to 15 Enable Auto Edit Function of the Film Annotation Character Format must remain No. After the FilmStrFmt file is edited, you should keep a record of the applied changes within the FilmStrFmt file in the form of a comment.

Edit the file in the format described later. Overwrite the contents of the FilmStrFmt file and then close Notepad (Notepad.exe).

u NOTES u
When editing the FilmStrFmt file, make sure to start it by performing Film annotation character settings in the Service Utility mode. Because character codes used in the FilmStrFmt file are based on the Unicode system, do not edit it directly. Use the Backup Utility function to obtain a backup copy of the Setup Information before performing editing. For the application software version upgrade processing, fully re-edit the FilmStrFmt file that is installed at upgrade processing, without restoring the FilmStrFmt file that has been backed up on an FD or the like.

6.

Click [Finish].
The system returns to the Service Utility top window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-74

MU-75
6.4.2 FilmStrFmt File Description Format
Following is the FilmStrFmt file description format.
Format name Example of description Area size and position FMT1 = (1202,188,L) [ Command SetFontTypeFace ("MS Gothic") ; Command for specifying the font type

Settings for one film annotation character format

Command for specifying the font size SetFontSize (55) ; FilmStrings(" ",%-10s), (0019,2F90); LineSpacing (1) ; Command for specifying the line spacing SetFontSize (30) ; FilmStrings(" ",%-20PN1), Command for specifying the character string (0010,0010); SetFontSize (48) ; Command for specifying the character string FilmStrings(%-10s," ",%-10s," ","[",%SEX1,"]"," ",%AGE1), (0010,0020),(0011,2F10),(0010,0040),(0010,0030); LineSpacing (10) ; SetFontSize (44) ; FilmStrings("EXP:",%DATE8," ","[",%TIME1,"]"," ","SC:",$MAG,"%"," ",$FUNC_PROC), (0008,0022),(0008,0032); ] F T1_1 = (1282,188,L) [

Settings for one film annotation character format ]

SetFontTypeFace ("MS Gothic") ;

FR000015-2.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-75

MU-76
Following are the details of each setting. Format name Describes the name of the format. Do not change the description for the CR-IR 391CL.

Cautions in editing the FilmStrFmt file


Following are the cautions to observe when editing the FilmStrFmt file. # at the top of a line indicates a comment line. Unnecessary spaces, tabs and line changes will be disregarded. Describe commands by the use of ; between them.

REFERENCE
The ImageSize.env file stored in the C:\ProgramData\Fujifilm\Hobbit\Config folder defines which format should be used by an output film. Area size and position Specify the area size and position between parentheses to the right of the format name, connecting them with each other using an equal sign (=). X-size, Y-size, position Item X-size Description Specifying the width of the film annotation character display area (0<X-size<4280pixel) Y-size Specifying the height of the film annotation character display area (0<Y-size<4280pixel) Position Specifying the position of characters in the film annotation character display area (C: centering, R: right padding, L: left padding) Command Describes the command for setting film annotation character format. Here, command format is similar to a programming language. These commands relate to fonts and character strings.
For details, see 6.4.3 Changing the Film Annotation Characters.

u NOTE u
Because FilmStrFmt is a Unicode-formatted text file, a Unicode- formatted NotePad included in the OS is necessary for file editing.

Font specifying commands Font specification Command Font type specification Font size specification Font style specification SetFontTypeFace SetFontSize SetFontStyle Command

Character string specifying commands Output character string specification

Line spacing specification LineSpacing Output format and attribute specification FilmStrings
020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-76

MU-77
6.4.3 Changing the Film Annotation Characters

Specifying the font size


Use the SetFontSize command to specify the font size. This command will be effective from the line describing SetFontSize to the line that directly precedes another SetFontSize description.

Specifying the font type


Use the SetFontTypeFace command to specify the font type. This command will be effective from the line describing SetFontTypeFace to the line that directly precedes another SetFontTypeFace description.

u NOTE u
Because no default values are available for font type, make sure to specify values for each film annotation character format. SetFontSize description format SetFontSize (font size); Specify a font size using values expressed in terms of pixels. SetFontSize description examples Specifying the font size to be 20 pixels SetFontSize(20); Specifying the font size to be 40 pixels SetFontSize(40); SetFontSize printout examples Font size specified as 20 pixels

u NOTE u
Because no default values are available for font type, make sure to specify values for each film annotation character format. SetFontTypeFace description format SetFontTypeFace (font name); Enclose a True-Type font name between quotation marks ( ). Any of the fonts that are available when Windows 2000 is installed can be specified. SetFontTypeFace description examples Specifying MS Gothic SetFontTypeFace(MS Gothic); Specifying Times New Roman SetFontTypeFace(TimesNewRoman); SetFontTypeFace printout examples MS Gothic specified

JOHN SMITH [M] 02247393 1938.04.08B


FR000018.EPS

G1.2G#0.70+0.30R4R0.5 PARANASAL SINUS


FR000016.EPS

Font size specified as 40 pixels

TimesNewRoman specified

JOHN SMITH [M] 02247393 1938.04.08B


FR000019.EPS

FR000017.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-77

MU-78
Specifying the font style
Use the SetFontStyle command to specify the font style. This command will be effective from the line describing SetFontStyle to the line that directly precedes another SetFontStyle description. SetFontStyle description format SetFontStyle (font style); Select either of the following. Bold : BOLD Italic : ITALIC When selecting the two font styles at the same time, use | to delimit them (ex.: BOLD|ITALIC).

Specifying the line spacing


Specify line spacing with the LineSpacing command. LineSpacing description format LineSpacing (line spacing); Use an integer between 1 and 400 (in terms of pixels) to specify line spacing for film annotation characters. LineSpacing description examples Specifying line spacing of 5 pixels LineSpacing(5); Specifying line spacing of 50 pixels LineSpacing(50); LineSpacing printout examples Line spacing of 5 pixels specified

u NOTE u
Specifying ITALIC for characters displayed in reverse video can make it look like they are missing in parts. ITALIC is thus disabled for reverse-video characters. SetFontStyle description examples Bold specified SetFontStyle (BOLD); Specifying bold and italic at the same time SetFontStyle (BOLD|ITALIC) ; SetFontStyle printout examples Bold specified

1234567890ABC

EXP: 1998.09.29 [10:42]

G1.2G#0.70+0.30R4R0.5
FR000024.EPS

Line spacing of 50 pixels specified

1234567890ABC

EXP: 1998.09.29 [10:42]

G1.2G#0.70+0.30R4R0.5
FR000025.EPS FR000020.EPS

Bold and italic specified

1234567890ABC EXP: 1998.09.29 [10:42]


FR000021.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-78

MU-79
Specifying print format and attributes
Use the FilmStrings command to specify character strings. FilmStrings description format FilmStrings(format descriptor1, format descriptor2, ),(attribute descriptor1),(attribute descriptor2) ; Format descriptor n Specifies the format descriptor that shows the format in which character strings are printed out. A maximum of 512 descriptors can be specified. However, the maximum total length of all character strings represented by the format descriptor is 256 characters.
For details, see 6.4.4 Format Descriptors.

FilmStrings description examples Printing out patient and exposure information The patient and exposure information indicated below are printed out. : Character string of variable length, up to 20 characters Patient name : [+M or F+] Sex : Character string of variable length, up to 15 characters Patient ID : YYYY.MM.DD + B Date of birth Date of examination : Character string of variable length, up to 15 characters Date of exposure : EXP+ YYYY.MM.DD Time of exposure : [+HH:MM+] FilmStrings(,%*20s,[,%SEX2,]),(0010,0010),(0010,0040); FilmStrings(,%*15s,,%DATE1,B),(0010,0020),(0010,0030); FilmStrings(,%*15s),(0008,0050); FilmStrings(EXP:,%DATE1,[,%TIME1,]),(0008,0020),(0008,0030) Printing out image processing parameters The following image processing parameters are printed out. : G + GA + GT + # + GC + GS Gradation processing parameters : R + RN + RT + RE Frequency processing parameters : L + latitude Latitude (L value) System sensitivity (S value) : S + system sensitivity : C + gradation correction + density Corrections (gradation and density) correction Image magnif./reduc. rate : SCALE: + percentage FilmStrings( ,$IMG_PROC); FilmStrings( ,$L,$S,$CS_SS, ,SCALE:,$MAG,%);

Attribute descriptor n Specifies the attribute descriptor that shows an attribute to be printed out as a character string. Basically, one attribute descriptor is given per format descriptor. The attribute descriptor is a tag number that represents the attribute to be printed out. It is not necessary to specify the attribute descriptor when the format descriptor is attribute-specific.
For details, see 6.4.5 Attribute Descriptors.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-79

MU-80
FilmStrings printout examples Patient and exposure information printout

6.4.4 Format Descriptors


Described herein are the format descriptor types and content presented in 6.4.3 Changing the Film Annotation Characters Specifying print format and attributes. Three format descriptor types are available. The first character of each format descriptor identifies the type.
FR000026.EPS

JOHN SMITH [M] 02247393 1998.04.08B 1234567890ABC EXP: 1998.09.29 [10:42]


Image processing parameters printout

First character
\ % $

Descriptor type
Character string control descriptor Character string style descriptor Attribute-specific format descriptor

G1.2G#0.70+0.30R4R0.5 L2.4S325C*1.0*1.0 SCALE: 100%


FR000027.EPS

REFERENCE
The C language command printf format-specified method has been adopted basically for the format descriptor that specifies the character string print format. However, the printf method has been expanded to make the following items available. Special print character formats, including characters in reverse video Some VR-specific patterns, including date format Information not assigned tag numbers, such as film image magnification/reduction Handling of a multiple number of attributes in a group (such as image processing parameters) Format descriptors not required by the printf method have been deleted.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-80

MU-81
Character string control descriptor (\)
Shown below are format descriptors that control character strings.
Descriptor
\t \r

Character string style descriptor (%)


This format descriptor indicates that the character string style is composed as follows. %[flag][width][type] [flag] Shows the information necessary for controlling character string length. Can be omitted. If [flag] has been specified, [width] must also be specified.
Flag description Description
Outputs character strings padded from the left. This is effective only when fixed length has been specified using [width]. If it has not, character strings will be output padded from the right. Shows that the character string length specified by [width] consists of a maximum number of characters. If the length of the character string to be output is longer than that specified by [width], it will be output as specified by [width]. If the length of the character string to be output is shorter than that specified by [width], it will be output as it actually is.

Description
Inserts tabs. Each tab is equivalent to 80 pixels. Displays the characters that follow in reverse video, which will be effective until \r is specified again.

Example of description

Example of printout

%*10s
[type] (s=character string data) [width]

ABCDEFGHIJ
A character string of a maximum of ten characters [flag] (*=maximum number of characters) A value specified by [width] FR000031.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-81

MU-82
[width] Shows the character string length. When * has been specified for [flag], this indicates the maximum character string length. When it has not, it indicates the fixed length. Only when f has been specified for [type] the a.b style specification will be effective, where a indicates the number of digits (of an integer) and b the number of decimal places. In this case, a can be omitted. Omitting a will not determine the number of digits while determining only the number of decimal places. When f has been specified for [type], it will not be possible to omit only b. Specifying 0 for b will cause an error. Example of description Example of printout [type] Shows the type of character string notation. This cannot be omitted. Two types are available: the standard type supported by C language and a special type added exclusively for film annotation characters. The standard type uses small letters to annotates character strings and the special type uses large alphanumerics. Numbers cannot be used at the beginning of character strings. The table below shows character strings annotation types. In the table, attributes other than those listed in the Attribute VR column (UN and SQ) cannot be output as film annotation characters. Standard type
Annotation type
d x f s

%*10d

1234567890
[type] (d=a decimally expressed An integer of a maximum of integer ) ten numbers [width] Character string length [flag] (*=maximum number of characters)

Attribute VR
OB,OW,SL,SS, UL,US AT,OB,OW,SL, SS,UL,US FL,FD AE,AS,CS,DS, DT,IS,LO,LT, PN,SH,ST,UI

Note
Outputs binary data in decimal form. Image data and overlay data cannot be selected. Outputs binary data in hexadecimal form. Letters will be output in capitals. Outputs binary data in floating-decimal-point form. Outputs character string data. Character strings of a maximum length of 256 characters can be output.

Example of description

Example of printout

%*5.1f
[type] (f=decimally expressed floating-point number) [width] Character string length [flag] (*maximum number of characters)

1234.2
A maximum of five integers, one decimally expressed floating-point number
FR000032.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-82

MU-83
Special type
Annotation type Attribute VR Note
Outputs various date display patterns in accordance with the values specified by n. Patterns are as follows. DATE1 : 1998.12.13 DATE2 : 1998.DEC.13 DATE3 : 12.13.1998 DATE4 : DEC.13.1998 DATE5 : 13.12.1998 DATE6 : 13.DEC.1998 DATE7 : H1.01.13 DATE8 : 1.01.13 Outputs various time display patterns in accordance with the values specified by n. This setting is valid only for information for which Attribute VR has been set to TM. Patterns are as follows. TIME1 : 10:51 TIME2 : 10:51:20 TIME3 : AM 10:51

Attribute-specific format descriptor ($)


The attribute-specific format descriptor is used for outputting a multiple number of attributes in groups or for outputting information that has not been assigned tag numbers. The attribute-specific format descriptor requires no attribute descriptors (the tag numbers shown below). The table below presents attribute-specific format descriptors. Table of attribute-specific format descriptors (1/2)
Descriptor Information displayed Sample character format
Outputs image processing parameters (G,R,O,D,U,H,P). Parameter output will depend on the image processing parameter formats described hereafter.

DATEn

DA

Note
Processing parameters for any processing that is not subjected to in view of processing path will not be output.

TIMEn

TM

Image $IMG_PROC processing parameter

AGEn

Outputs various age display patterns in accordance with the values specified by n. This setting is valid only for information on date of birth. Patterns are as follows. AGE1: 25 years, 1 year and 8 months, 1 month and 10 days, DA 13 days (date of birth AGE2: 25Y, 1Y8M, 1M10D, 13D Output format will differ with the relevant age, as follows. only) 0 years to 0 years and 1 month or under : ** days 0 years and 1 month up to 1 year : ** months 1 to 8 years : ** years and ** months 8 years or over :** years CS (sex only) Outputs sex display patterns in accordance with the values specified by n. This setting is valid only for information on sex. Patterns are as follows. SEX1: Male, female, (for others, 1 space) SEX2: M, F, O (for others, 1 space) Outputs name display patterns in accordance with the values specified by n. This setting is valid only for information with PN specified for VR. Display patterns follow. PN1: For printing kana alongside kanji (ANK characters are printed only when ideographic characters are used.) PN2: Only for use with ideographic characters (Ideographic characters are printed if used. Left blank if not used.) PN3: Only for single-byte characters (Single-byte characters are printed if used. Left blank if not used.) PN4: For display of multi-byte characters (Ideographic characters are printed if used. Single-byte characters are printed if they are not used. Left blank if neither are used.)

$GAMMA

Gradation processing parameter Frequency processing parameter 1D-USM processing parameter DRC processing parameter MFP-USM processing parameter MFP-DRC processing parameter PEM processing parameter

G 1.0G#1.6-0.20

Parameters will not be output during multi-frequency processing (MFP). Parameters will not be output if this process is not performed. Parameters will not be output if this process is not performed. Parameters will not be output if this process is not performed. Parameters will not be output if this process is not performed. Parameters will not be output if this process is not performed.

$BETA

R 4R0.5

$1DUSM

O 3V1.0

SEXn

$DRC

D 2A0.8

$H_USM

U FA0.8

$H_DRC

H FA0.8

PNn

PN

$PEM

P ABC1.5

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-83

MU-84
Table of attribute-specific format descriptors (2/2)
Descriptor Information displayed
Image processing * parameter change mark Term of correction FCR image ID Right-andleft reversal mark (1/2) Right-andleft reversal mark (2/2) IP number Image magnif. rate Pair processing information

6.4.5 Attribute Descriptors


Note

Sample character format

$MOD

Parameters will be output only when they have been changed.

Described next are the specific types and contents of the attribute descriptors discussed in Specifying print format and attributes under 6.4.3 Changing the Film Annotation Characters. The attribute descriptor is information used to specify several kinds of attributes to be printed out as film annotation characters. One attribute descriptor can be described for each format descriptor. The attribute descriptor represents a tag number for the attribute to be printed out.

$CS_SS $FCR_ID $AP_PA1

C *1.0/1.5 C 001

For both gradation correction and density correction, parameters are output converted to character strings. IDs will be output by changing the image numbers. Can be output only when image is reversed. PA will be output when reversed and AP when not reversed. IP numbers will be output removing a and c before and after the IP number respectively. Can be output only when the image size requested has been set.

Attribute descriptor description format


Following is the attribute descriptor description format. (gggg,eeee) gggg : Group number. Fixed four digits in hexadecimal form. eeee : Element number. Fixed four digits in hexadecimal form.

$AP_PA2

AP (PA)

$IP_NUM $MAG _RATE

0412657 67 RT-01 is for image processing type RT.

Attribute descriptor description cautions


Parentheses ( ) are required when describing a tag number. Use a comma , between attributes. Use a comma , between a group and an element. If the specified tag is not available, use one half-size space. For the patients name, create a character string after delimitation conversion. When printing out a kanji character string, remove the ESC sequence and then create the string. Handle control characters within LT and ST as spaces. For a tag for which VM is 1 or more, only the head information will be printed out. However, information for the character string will be printed out including the \ that represents delimitation.

$FUNC _PROC

Image processing type (0019,2F40) Set numbers (0021,2F30) Image numbers in the set (0021,2F40) ES 01 02-01 is for Pair processing information numbers an image processing (0021.2F50) type other than RT. This information is output only when all of the four energy subtraction parameters are within the range between A and T. Energy subtraction parameter (50F1, 2F06). Subtraction registration result (50F1, 2F07) Normal : @ is not added. Abnormal : @ is added. Pixel value (0018, 1164) while an image is read, as well as pixel value (used for image processing) while it is printed will be output. **** will be output when no pixel value information is available.

$ES

Energy subtraction information

E AGGH @

$L $S

L value S value

L 2.0 S 20000

$IMG_PS

Pixel value

0.10->0.15

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-84

MU-85
Attributes that can be printed out using the CR-IR 391CL
Tables below show attributes that can be output using the CR-IR 391CLs DICOM Print function. Attributes that can be printed out using the CR-IR 391CL and its attribute descriptors (1/3)
Attribute
1 2 3 4 Hospital (institution) name IP number EDR mode Menu code System ID Image number Image proc. conditions Gradation proc. Frequency proc. 1D-USM 5 DRC MFP-USM MFP-DRC Image proc. condition change mark GPR FNC 6 Exposure menu name Normalization conditions + correction term Latitude 7 System sensitivity Correction term 8 Patient ID Latitude identification character Latitude System sensitivity identification character System sensitivity Correction term identification character, gradation correction, density correction GPR processing flag FNC processing flag kanji ANK CHEST GENERAL -identifying characters GA, GT, GC, GS -identifying characters RN, RT, RE 1D-USM identification characters ORN, ORD, ORE DRC identification characters DRN, DRT, DRE MFP-USM identification characters HRN, HRT, HRE MFP-DRC identification characters HDN, HDT, HDE A to Z The last 3 digits in decimal expression. kanji ANK Excluding a and c. FUJI HOSPITAL 04012657

Annotation

Film annotation characters


%s %s

Format descriptor

Attribute descriptor
(0009, 2F80) (0008, 0080) (0018, 1004) (0019, 2F50) (0018, 1401) (0019, 2F32) (0018, 1400) (0010, 0020)

$IP_NUM $EDR_MODE %s $FCR_ID $IMG_PROC

A, S, F , M
0900

A 001

G .0G#1.6-0.20 R 4R0.5 O 3V1.0 D 2A0.8 U FA0.8 H FA0.8

$GAMMA $BETA $1DUSM $DRC $H-USM $H_DRC $MOD $GPR $FNC %s %s

G F

L 2.0 S 20000 C *1.0/1.5


1010181139

$L $S $CS_SS %s

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-85

MU-86
Attributes that can be printed out using the CR-IR 391CL and its attribute descriptors (2/3)
Attribute
9 Patient name kanji ANK FUJI TARO
EXP: ..

Annotation

Film annotation characters


%s %s

Format descriptor

Attribute descriptor
(0011, 2F10) (0010, 0010)

: EXP:

ANSI short format ANSI long format 10 Date of exposure American short format American long format European short format European long format Japanese date format Japanese date (kanji) format 11 Sex: kanji Sex: ANK kanji Alphabet Y, YM, MD, D Age 12 Date of birth 13 Pair proc. Routine proc. kanji Alphanumerics YYYY.MM.DD YYYY.MM.DDB Proc. type, pair no., IP and IL Indicates the routine and serial routine processing nos. Hour and minute Film annotation characters1

1998.12.13 1998.DEC.13 12.13.1998 DEC.13.1998 13.12.1998 13.DEC.1998 H10.12.13 10.12.13 [ ] or [ ] [M] or [F] 25 , 1 8 25Y, 1Y8M 1M10D, 13D 1989.12.13 1989.12.13B ES01 02-01 RT-01 [10:51] PA : 100% ,1 10 , 13

%DATE1 %DATE2 %DATE3 %DATE4 %DATE5 %DATE6 %DATE7 %DATE8 %SEX1 %SEX2 %AGE1 %AGE2 %DATEn, %DATEn, B $FUNC_PROC [ ,%TIME1, ] %s : $MAG, % SCALE:, $MAG, % :,% (0029, 2F50) (0029, 2F50) (0008, 0030) (0019, 2F90) (0010, 0030) (0010, 0040) (0010, 0040) (0008, 0020)

14 Time of exposure 15 Film mark 16 Magnif./reduc. rate

SCALE : 100% 17 Patient name (2) 18 Data compression code : 22 CC : 22

CC:,%s

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-86

MU-87
Attributes that can be printed out using the CR-IR 391CL and its attribute descriptors (3/3)
Attribute
19 Energy subtraction information 20 Right-and-left reversal mark

Annotation
Error flag for energy subtraction parameter table identification characters Ta, Tb, Tc, Td (only at error occurrence)

Film annotation characters E AGGH @ R , AP (PA)


$ES

Format descriptor

Attribute descriptor

$AP_PA1 or $AP_PA2

To print out attributes other than those listed above, set the relative tag number of the attribute specified in the Conformance Statement.
See DICOM Conformance Statement.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-87

MU-88
6.4.6 Film Annotation Character Verification Procedure
FilmStrFmt file editing results can be verified using the Service Utility. The procedure is described below.

6.5 Person Name


Perform setup for converting an entered person name.

1. 2. 3.

Start the Service Utility.


The Service Utility top window opens.

1. 2.

Start the Service Utility.


The Service Utility top window opens.

Click [Film annotation characters].


The Setting film annotation characters window opens.

Click [Person name].


The Person name setting window opens.

Click [Displaying film annotation characters].


The Display film annotation characters window opens.

NOTE
If there is any incorrect setting, the message [60642 Film annotation character generation has failed may appear on the display.

4.

Click the downward arrow mark ( type from the pull-down menu.

) for FMT1 and select a format

REFERENCE
FMTX_1 : Film annotation character definition for 20 pix/mm images. (If FMTX_2 is also provided, it is used for 20 pix/mm images.) FMTX_M : Film annotation character definition for mammographic images.

5. 6. 7. 8.

Click [OK].
The film annotation characters are displayed in the selected format.

Click [Finish].
The system returns to the Setting film annotation characters window.

To verify the other film annotation characters, repeat Steps 4 and 5. Click [Finish].
The system returns to the Service Utility top window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-88

MU-89
3.
Click the downward arrow mark ( down menu. ) for

4.

Double-click the Setup value field on the right-hand side.

and choose USER_IF from the pull-

NOTES
Do not change the settings for DICOM_IN and DICOM_OUT because they represent the standard DICOM specifications. As regards USER_IF, modify relevant settings only.
The USER_IF classification appears in the window.

Setup value field


MU000010.ai

5.

Change the setup value.


If the double-clicked field looks like field) :
I. Use the mouse to select a desired text and enter it from the keyboard. If the double-clicked field consists of a check box : The check box alternates between ON and OFF each time it is doubleclicked.

(direct input

6.

Perform the setup steps indicated below:


I. II. III.
00000424.ai

I.

To validate this standard (condition) change, checkmark it (

).

II. Enter a one-byte character delimiter between name elements.

NOTES
Any one-byte characters can be used as a delimiter. However, a one-byte space ( ), hyphen (-), comma (,) or period (.) should normally be used. One or two kinds of delimiters can be defined (either can be used as a delimiter). For instance, enter -, if you wish to define both of hyphen and comma. Input example: Element3=given, middle-family As regards Delimiter1 for USER_IF, a one-byte space is set as a default.

MU000009.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-89

MU-90
III. Enter a multi-byte character delimiter between name elements.

8.

Set up name elements for multi-byte characters. Enter name elements directly on the keyboard. To separate one name element from the other, use a delimiter defined in Step 6. above.
One name element (family (name)) Two name elements (family given) Three name elements (family given middle) Four name elements (family given middle prefix) Five name elements (family given middle prefix suffix)
MU000052.EPS

NOTES
Any one- or two-byte characters can be used as a delimiter. However, a twobyte space ( ) or hyphen () should normally be used. One or two kinds of delimiters can be defined (either can be used as a delimiter). For instance, enter if you wish to define both of two-byte space and hyphen. Input example: Element3=given middle family As regards Delimiter2 for USER_IF, a two-byte space is set as a default.

7.

Set up name elements for one-byte characters. Enter name elements directly on the keyboard. To separate one name element from the other, use a delimiter defined in Step 6. above.
One name element (family (name)) Two name elements (family given) Three name elements (family given middle) Four name elements (family given middle prefix) Five name elements (family given middle prefix suffix)
MU000051.EPS

9.

Click [OK].
The system returns to the Service Utility top window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-90

MU-91 6.6 Modality Settings


CR-IR 391CL can apply following modality lut to the image according to the modality of each image. N/A, P-Value, gamma 2.2, FCR Perform LUT setting corresponding to each modality.

4.

Select the LUT to be set from the pull-down menu.

1. 2. 3.

Start the service utility.


The Service Utility top window opens.

Click [Modality setting].


The Modality Settings window opens.

Click the Gradation characteristic of image column of the image type for which the setting is to be changed.
A pull-down menu button is displayed for the respective Gradation characteristic of image column.

MU060211.EPS

5.

Click [OK].
The system returns to the Service Utility top window.

MU060210.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-91

MU-92

7. Maintenance Tool
Use the maintenance tool to achieve recovery or perform a maintenance task during installation or troubleshooting.

7.1 Database Utility


The term DB may be used to represent a database. The database utility is used to initialize the image database, delete output images from the image output queue (clear the image output queue), or initialize the patient database.

WARNING
Exercising a function of the database utility deletes all images from the local database. Before using a database utility function, be sure to verify that all recovery images are stored on a DVD. For details on the recovery procedure, see under 1.14 Reconstructing the Image Database under MC: Checks, Replacement and Adjustment of Parts.

MU000016.ai

Name
Database utility Acquiring EDR backup data

Description
Discards the current database and creates a new one. Acquires or stores the EDR backup data about a selected local image.

Connection check Checks the connections to the equipment that is defined through Connected equipment under Service settings. Log display/edit Event log display Displays or clears the number of IP exposures. Starts Event Viewer of the OS.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-92

MU-93
7.1.1 Initializing the Patient Database
This section describes the procedure for discarding the current patient database and creating a new one.

4.

Click [OK].
The command prompt window for an initialization process opens.

1. 2.

Start the Service Utility.


The Service Utility top window opens.

Click [Database Utility].


The Database Utility window opens.

MU000011.EPS

Wait until the message Press any key to continue... appears.

MU000012.EPS

5. 6. 7.

Press any key on the keyboard.


The Console verification window opens.

Click [OK].
The system returns to the Database Utility window.

Click [Finish].
The system returns to the Service Utility top window.

MU000033.ai

3.

Click [The patient database is initialized.].


The Console warning window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-93

MU-94
7.1.2 Initializing the Output Queue
This section describes the procedure for deleting remaining output requests from the current output queue.

2.

Click [Database Utility].


The Database Utility window opens.

NOTE
If images are left on the image output queue, it means that a connected equipment failure or other abnormality has occurred. Confirm the status that is indicated as output queue information, see the symptoms in the MT: Machine Troubleshooting, determine the cause of abnormality, and take appropriate remedial action.

1.

Start the Service Utility.


The Service Utility top window opens.

MU000033.ai

3.

Click [The image output queue is initialized.].


The Console warning window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-94

MU-95
4.
Click [OK].
The command prompt window for an initialization process opens.

MU000011.EPS

The Console verification window opens.

5. 6.

Click [OK].
The system returns to the Database Utility window.

Click [Finish].
The system returns to the Service Utility top window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-95

MU-96
7.1.3 Initializing the Image Database
This section describes the procedure for deleting the local image, discarding the image database, and creating a new one.

2.

Click [Database Utility].


The Database Utility window opens.

NOTES
Database can be initialized only when SQL Server has been running. If SQL Server is not running, restart the PC. If images are left on the image output queue, it is not possible to initialize the database. Initialize the image database after verifying that the images are fully output from the output queue.
For the procedure for deleting images from the image output queue, see 7.1.2 Initializing the Output Queue.

1.

Start the Service Utility.


The Service Utility top window opens.

MU000033.ai

3.

Click [Image database is initialized.].


The Console warning window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-96

MU-97
4.
Click [OK].
The command prompt window for an initialization process opens.

NOTE
If the following message appears, it means that the images contained in the image database are not initialized. It failed in initialized DB. Verify that the SQL Server is running and that no image is left on the image output queue. To restart the SQL Server I. Restart the PC.
MU000011.EPS

Wait until the message Press any key to continue... appears.

II. Select Control Panel from the Tool.

menu and double-click Administrative

III. Double-click Computer Management. IV. Select Computer Management - Services and Applications - SQL Server Configuration Manager - SQL Server 2005 Services. V. Confirm that SQL Server(MSSQLSERVER) is running. If images are left on the image output queue Deletes the images from the image output queue.
MU000013.EPS

For the procedure for deleting images from the image output queue, see 7.1.2 Initializing the Output Queue.

5. 6. 7.

Press any key on the keyboard.


The Console verification window opens.

Click [OK].
The system returns to the Database Utility window.

Click [Finish].
The system returns to the Service Utility top window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-97

MU-98
7.1.4 Initializing the Preset DB
This section describes the procedure for discarding the current preset database and creating a new one.

4.

Click [OK].
The command prompt window for an initialization process opens. Wait until the message Press any key to continue... appears.

1. 2.

Start the Service Utility.


The Service Utility top window opens.

5. 6. 7.

Press any key on the keyboard.


The Console verification window opens.

Click [Database Utility].


The Database Utility window opens.

Click [OK].
The system returns to the Database Utility window.

Click [Finish].
The system returns to the Service Utility top window.

MU000033.ai

3.

Click [Initialized Preset DB.].


The Console warning window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-98

MU-99 7.2 Acquiring EDR Backup Data


This section describes the procedure for acquiring/storing the EDR backup data file for a selected local image. The EDR backup data is used, for instance, to analyze image processing abnormalities and other troubles.

3.

Select one or more pieces of EDR data.


I. Click an EDR data item. The selected item is then highlighted.

Selecting only one piece of EDR data

1. 2.

Start the Service Utility.


The Service Utility top window opens.

Selecting two or more consecutive pieces of EDR data (selecting all pieces of data between A and B in the window shown below)

Click [Acquiring EDR backup data].


The Acquiring EDR backup data window opens.

A B

I. II.

REFERENCE
EDR data is not displayed at the time of installation. It appears in a list after an image is transferred to the CR-IR 391CL.

MU000027.EPS

I.

Click the first item of the consecutive data items (the FCRImageID: A001 data in the window shown above). The selected item is then highlighted.

II. Hold down the <Shift> key and click the last item of the consecutive items (the FCRImageID: A003 data in the window shown above). All items between the first and the last are then highlighted.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-99

MU-100
Selecting two or more nonconsecutive pieces of EDR data

5.

Select a save destination directory and then click [OK].

REFERENCE
I. II. III.

If drive a: is selected, a message appears prompting you to insert an FD into its drive.

6.

Click [Finish].
The system returns to the Service Utility top window.

MU000057.EPS

I.

Click the first item (click FCRImageID: A001 in the window shown above). The selected item is then highlighted.

II. Hold down the <Ctrl> key and click the second item (click FCRImageID: A002 in the window shown above). The second item is then additionally highlighted. III. Hold down the <Ctrl> key and click the next item (click FCRImageID: A003 in the window shown above). The third item is then additionally highlighted. IV. Select the other items as needed by repeating step III.

REFERENCE
Even if the selected items are hidden due to scrolling, they remain selected.

4.

Click [Save the EDR function].


A window opens, prompting you to specify the save destination.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-100

MU-101 7.3 Connection Check


This section describes the procedure for checking the connection to the equipment that is defined through Connected equipment under Service settings. The connection check procedure varies depending on whether the connection to a host device or DICOM device is to be checked. Checking the connection to a DICOM device

NOTE
When checking the connection between DICOM devices, it is necessary to the Verification service class be supported by both the local device and the other device.
For details on the setup procedure, see 6.2.3 DICOM Settings.

1. 2. 3.

Start the Service Utility.


The Service Utility top window opens. I.

Click [Connection check].


The Connection check window opens.

Check the connection to host equipment or DICOM device.


I. Click the downward arrow mark ( ) for RU0 under Check connection to the host equipment to open the pull-down menu. Select host equipment that is registered as Connected equipment. A host name appears. If no host name is assigned, an IP address appears.

Click the downward arrow mark ( ) for under DICOM Verification to open the pull-down menu. Select a DICOM device that is registered as Connected equipment. Registered DICOM devices whose Verification setting is ON are then displayed. The Verification setting is defined through DICOM setting under Service settings.

Check connection to the host equipment

II. Click [Verify connection]. When the message DICOM Verification was succeeded. appears in the FFServiceUtility window, the connection is normal.

NOTE
If the message DICOM Verification was failed. appears, use the Simplified setup wizard to check the associated setting. See the Service Manual for the connected equipment, and ensure that the DICOM communication is properly established.
III. Close the dialog box. The system returns to the Connection check window.

II. Click [Verify connection]. The command prompt window opens. When the command prompt window displays the following message four times, the connection is normal. Reply from 172.16.1.10: bytes=32 time<10ms TTL=128

REFERENCE
The displayed values time<10ms and TTL=128, which are included in the above message, vary with the network condition. However, the connection is normal no matter what values are displayed.

4.

Click [Finish].
The system returns to the Service Utility top window.

NOTE
If the message Request timed out. appears, use the Simplified setup wizard to check the associated setting. Further, check the power supplies and connections for network devices (LAN cables, hub, etc.) to ensure that the communication with the connected equipment is normally established.
III. Close the command prompt window by clicking its mark. The system returns to the Connection check window.
020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-101

MU-102 7.4 Log Display/Edit


This section describes the procedure for displaying/clearing the number of IP exposures (IP exposure count).

4.

Click [Delete].
A confirmation window opens.

1. 2. 3.

Start the Service Utility.


The Service Utility top window opens.

Click [Log display/edit].


The Editing/displaying logs window opens.

Select an IP whose exposure count is to be cleared.

MU000058.EPS

NOTE
Before clearing the exposure count (the number of exposures), be sure to check that its history is saved.

5.

Click [OK].
The selected IP is then deleted from the list.

MU000056.ai MU000026.EPS

6.

Click [Finish].
The system returns to the Service Utility top window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-102

MU-103 7.5 Event Log Display


This section describes the procedure for starting Windows Vistas Event Viewer for trouble analysis purposes.

1. 2. 3.

Start the Service Utility.


The Service Utility top window opens.

Click [Event log display].


Windows Vistas Event Viewer starts.

Check the event log.


For the configuration of the Event Viewer window and the information on how to view the Event Viewer window, see 2.3 Configuration and How to View the Event Viewer under MT: Machine Troubleshooting.

4.

Exit the Event Viewer by clicking the main window.

mark on the Event Viewer

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-103

MU-104
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-104

MU-105
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-105

MU-106
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

MU-106

Appx MU 1-1

Appendix 1 Backup Utility


Use the Backup Utility to back up patient information, setup information, and log information.

Removing the disk


Remove the storage disk as directed below.

1.

Click

in the upper right corner of the Study List window.

Preparations
Make sure that all images are written on a storage disk. Attach a label to the case of a backup disk, write a date on the label, and mark it as a Backup disk. Determine the version of the application, and write the version on the label attached to the Backup disk case.
IN000512.ai

The Indicator window (disk) opens.

IN000620.ai

2. 3.

Click [Eject].
The DVD drive tray opens.

Remove the disk. Insert it into the case with the front surface facing upward.

NOTE
Attach a label to the case, mark it as a Storage disk, and write the date on the label.

4.
020-221-01E 04.28.2009 FM5535

Close the empty tray.

CR-IR 391CL Service Manual

Appx MU 1-1

Appx MU 1-2
5.
Click [Update].
Only Device Name is displayed. Status, Usage, and Disk Writing are hidden.

7.

Click [Close] in the upper left corner of the Study List window.

REFERENCE
For V1.1(B) or later, click at the bottom of the Main Window.

IN000633.ai

The [20339] Application will be terminated dialog box opens.

MUApp0002.ai

6.

Click [OK].
The system returns to the Study List window.
IN000625.ai

8.

Click [OK].
The system returns to the desktop screen.

IN00062 .ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MU 1-2

Appx MU 1-3
Backup
Preparations
When the CR-IR 391CL is not running:

Starting the Backup Utility

1.
.

Right-click the CR-IR 391CL server icon in the task tray, which is located in the lower right corner of the desktop screen.

1.

In the desktop screen, double-click

IN000402.ai

The CR-IR 391CL starts and then the user selection window opens.

The right-click menu opens.

2. 1.

Click [Finish] in the lower left corner of the user selection window.

2.

Click [Backup Utility].


A confirmation window opens.

When the CR-IR 391CL is running:

Click [Close] in the upper left corner of the Study List window.

REFERENCE
For V1.1(B) or later, click at the bottom of the Main Window.

MU000034.ai

IN000633.ai

3.

Click [OK].
After the system is shut down, the User authentication window opens.

A confirmation dialog box opens.

IN000635.ai

IN000625 ai

2.

Click [OK].
The client application exits.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MU 1-3

Appx MU 1-4
4.
From the keyboard, enter the username medicalservice and the password fieldengineer.

6.

Click [Backup].
The Backup window opens.

NOTES
The username and password both consist of 1-byte lower-case characters only. Do not include any space. Since the medicalservice user is not registered in the pull-down menu, be sure to enter the username from the keyboard.

IN000626.ai

MU000035.ai

7.

Put a checkmark on each of the following items (by changing


Patient information Setup information Log information Delete logs after completing backup processing.

):

5.

Click [OK].
The Main Menu window opens.

8. 9.

Click [Start].
The Select folder window opens.

Open the DVD drive tray, and insert the backup disk into the tray.

MU000036.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 1-4

Appx MU 1-5
10. Complete the following checks and then click [OK]. 11. Click [OK].
The disk formatting confirmation window opens.

IN000627.ai

I.

Check that the current drive is D:. Also, check that the folder name represents the execution date and time (YYYYMMDDhhmmss).

MUApp0004.ai

The log information deletion confirmation window opens.

NOTE
If you insert a formatted disk in this step, the above disk formatting confirmation window does not open; however, the following message appears. Click [OK] in response to the message because the backup process remains unaffected.

MUApp0003.ai

MU000040.EPS

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 1-5

Appx MU 1-6
12. Click [OK].
The backup destination folder creation confirmation window opens.

Post-backup confirmation

1.

Select Computer from the

menu and double-click DVD drive

(D:). And then check to make certain that the files shown on the following screen shot are stored.

IN000628.EPS

13. Click [OK].


Upon completion of backup processing, the completion window opens.

IN000629.ai

2.
MU000042.ai

Remove the backup disk from the DVD drive, and then insert the storage disk. In the Select Server Application Behavior window, select Start up Client Application and click [OK].

3.

14. Click [OK].


The system returns to the Main Menu window.

15. Click [Finish].


The system returns to the desktop window.

IN000636.ai

The log-in window opens.


020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 1-6

Appx MU 1-7
4.
Log in as Service Engineer.
For the procedure for logging in as Service Engineer, see 5.3 Checking Every Step from the Inputting of Images to the Saving of Images onto DVD under IN: Installation.

8.

Verify that no error information is recorded as an event.

REFERENCE
For V1.1(B) or later.

MUApp0021.ai

The Study List window opens.


IN000631.ai

5. 6.

Click

under the

9.

Click [OK].
The system returns to the Study List window.

Verify that the list on the storage disk is displayed.

10. Click [Close] in the upper left corner of the Study List window.
The [20339] Application will be terminated dialog box opens.

IN000630.ai

IN000625.ai

7.

Click

in the indicator section.

11. Click [OK].


The system returns to the desktop screen.

The Indicator window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MU 1-7

Appx MU 1-8
Restore (information restoration)

4.

1. 2.

Insert the backup disk into the DVD drive. In the Main Menu window, click [Restore].
For the procedure for starting the Backup Utility, see Starting the Backup Utility.

Specify the data folder on the backup disk that is to be restored, and then click [OK].

MUApp0008.EPS

The system returns to the Select folder window.

5.
MU000036.ai

Verify that the folder specified in Step 4 is displayed, and then click [OK].

The Select folder window opens.

MUApp0009.EPS

The Restore window opens.


MUApp0006.EPS

3.

Click [Browse].
The Browse For Folder window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 1-8

Appx MU 1-9
6.
From Select Information to be restored, select Menu Setting Information, System configuration information, User information, and Explanatory information.

7.

Click [Start].
Upon completion of restore, the Confirmation window opens.

MUApp0011.EPS

NOTE
To restore IP use count data I. Put a checkmark in the IP counter information check box (by changing ).
II. Click [Start]. The [64402] IP use count data will be restored window opens.

MU000045.EPS

MC000215.EPS

III. Click [OK]. The restore completion window opens.

8.

Click [OK].
The system returns to the Main Menu window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 1-9

Appx MU 1-10
9.
Click [Finish].
The system returns to the desktop screen.

Collecting logs for maintenance purpose


The procedure for collecting analysis logs is described below.

10. Verify the system configuration information.


For the procedure for verifying the system configuration information, see 5. Checkup Work under IN: Installation.

CAUTION
When acquiring or taking out personal information, observe the sales representatives rules that are based on the local laws and regulations. When collecting logs, it is recommended that you use, for instance, a USB memory having an adequate security function, and exercise due care in handling it.

11. Verify the user information and explanatory information.


For the procedure for verifying the user information and explanatory information, see Appendix 3: Creating a User.

NOTE
The information specific to the user environment must be verified in the presence of the user.

1.

In the Main Menu window, click [Collecting logs for maintenance purpose].
For the procedure for starting the Backup Utility, see Starting the Backup Utility.

MU000036.ai

The Collecting Logs for Maintenance Purpose window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 1-10

Appx MU 1-11
2.
Put a checkmark in the Delete personal information off of the logs or Do not delete personal information off of the logs check box, and then click [Start].

3.

Click [Browse].

NOTE
When collecting maintenance logs without deleting the personal information, observe the instructions set forth under CAUTION at the beginning of Collecting logs for maintenance purpose.

MUApp0020p.EPS

The Browse For Folder window opens.

4.

Specify the folder for analysis log storage, and then click [OK].

MUApp0013.EPS

The system returns to the Select folder window.


MUApp0019.EPS

The Select folder window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 1-11

Appx MU 1-12
5.
Verify that the folder specified in Step 4 is displayed, and then click [OK].

8.

Verify that BackupInfo.ini and MAINTENANCE.cab are created in the folder specified in Step 4.

MUApp0016.EPS

9.
MUApp0014.EPS

Check to see that the Study.txt file is created on the desktop.

IMPORTANT
Show Study.txt to the user to give evidence of the fact that the personal information was deleted certainly. After showing Study.txt to the user, delete it unfailingly.

The Confirmation window opens.

MUApp0017.EPS

6. 7.

Click [OK].
The system returns to the Main Menu window.

Click [Finish].
The system returns to the desktop screen.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 1-12

Appx MU 2-1

Appendix 2 User Utility


Preparations
When the CR-IR 391CL is not running:

Setting a destination for automatic image output


NOTE
Before performing the procedure set forth below, complete network information setup. Use the automatic output destination setup function to select non-default settings for image output to output devices at the time of an image read from the RU device. For the DVD, which is a standard component, the automatic output function is enabled for image backup purposes. For the optional DICOM printer and generalpurpose files, however, the automatic output function is disabled by the default. Therefore, when an output is to be automatically delivered to the above optional output destinations, be sure to complete the setup procedure described below.

1.

In the desktop screen, double-click

The CR-IR 391CL starts and then the user selection window opens.

2. 1.

Click [Finish] in the lower left corner of the user selection window.

When the CR-IR 391CL is running:


Click [Close] in the upper left corner of the Study List window.
A confirmation dialog box opens.

1.

Right-click the CR-IR 391CL server icon in the task tray, which is located in the lower right corner of the desktop screen.

IN000402.ai

The right-click menu opens.

2.

Click [User Utility].


A confirmation window opens.

IN000625 ai

2. 3.

Click [OK].
The Select Server Application Behavior window opens.

Select Exit and Click [OK].


The client application exits.
INApp0007.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MU 2-1

Appx MU 2-2
3.
Click [OK].
After the system is shut down, the User authentication window opens.

5.

Click [OK].
The Main Menu window opens.

IN000635.ai

4.

From the keyboard, enter the username medicalservice and the password fieldengineer.

NOTES
The username and password both consist of 1-byte lower-case characters only. Do not include any space. Since the medicalservice user is not registered in the pull-down menu, be sure to enter the username from the keyboard.
INApp0008.ai

MU000035.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 2-2

Appx MU 2-3
6.
Click [Output Destination Settings].
The Setting destination for image output window opens.

11. Click [OK].


The system returns to the Main Menu window.

12. Click [Finish].


The Application is now being activated. window opens.

INAppM0001.EPS INApp0009.ai

The system starts up and then the User selection window opens.

REFERENCES
Printer is displayed only when the DICOM print option is installed. DICOM transmission is displayed only when the Storage in a DICOM storage device option is installed.

NOTE
For a General-purpose file, set up the Naming rule of general-purpose image files. See Setting the naming rule of general-purpose image files.

7. 8. 9.

Click an output destination tab for automatic output. Put a checkmark in the Automatic image output check box (by changing to ). Set the Destination for data transfer and Timing of output.

10. When setting another output destination, repeat Steps 7 to 9.


020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 2-3

Appx MU 2-4
Setting the naming rule of general-purpose image files Automatic verification of a study
The CR-IR 391CL involves the use of a Confirmation procedure, which is performed by the user to confirm an image read from the RU device, and a Verification procedure that is performed to finish a study. The automatic verification procedure set forth below is used to either confirm a study the moment it is verified by the user or automatically verify a study when a preselected period of time elapses after confirmation. When the above automatic verification function is used in conjunction with the automatic image output destination setup function, it is possible to generate an output on the basis of automatic verification.

1. 2.

Open the Setting destination for image output window. Click to open the General-Purpose File tab.

1.

Right-click the CR-IR 391CL server icon in the task tray, which is located in the lower right corner of the desktop screen.

IN000402.ai

The right-click menu opens.


INApp0010.ai

2.

Click [User Utility].


A confirmation window opens.

3. 4.

Click the downward arrow mark (


A pull-down menu opens.

) for Type1.

Select the format to be set.


I. For CR study
Description
Sequential No. Example: Img0008.jpg Host name+Date+Sequential No. Example: CVXXXXXXXX260004.jpg Patient ID+Study Date+Exposure Region+Sequential No.+Host name Example: 0123456789051026TEST0006CVXXXXXXXX.jpg
INApp0007.EPS

Setting
Type0 Type1 Type2

II. For Endoscope study


Setting
Type0 Type1 Type2
020-221-02E 01.08.2010 FM5563

Description
Sequential No. Example: Img0008.jpg Host name+Date+Sequential No. Example: CVXXXXXXXX260004.jpg Patient ID+Study Date+Exposure Region+Sequential No.+Host name Example: 0123456789051026TEST0006CVXXXXXXXX.jpg

CR-IR 391CL Service Manual

Appx MU 2-4

Appx MU 2-5
3.
Click [OK].
After the system is shut down, the User authentication window opens.

5.

Click [OK].
The Main Menu window opens.

IN000635.ai

4.

From the keyboard, enter the username medicalservice and the password fieldengineer.

NOTES
The username and password both consist of 1-byte lower-case characters only. Do not include any space. Since the medicalservice user is not registered in the pull-down menu, be sure to enter the username from the keyboard.
INApp0008.ai

6.

Click [Auto-Determine Settings].


The Automatic verification of a study window opens.

MU000035.ai

MUApp0001.EPS

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 2-5

Appx MU 2-6
7. 8. 9.
Put a checkmark in the Automatically verifying a study check box (by changing to ). Choose either Completion of an exposure and its verification take place simultaneously. or Study is verified after the set time followed by exposure. Specify the Time required for automatic verification of a study by clicking the or by entering a desired value from the keyboard.

10. Click [OK].


The system returns to the Main Menu window.

11. Click [Finish].


The system returns to the desktop screen.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 2-6

Appx MU 2-7
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 2-7

Appx MU 2-8
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 2-8

Appx MU 3-1

Appendix 3 Creating a User


This section shows the procedures of creating a user to perform a check on image input/output, after completion of installation.

NOTE
The top, bottom, left, and right edge portion clicks should be done slowly. Too fast clicking may prevent the detection of correct position information.

3. 1.
Double-click on the desktop screen.

Enter the password fieldengineer (using only single-byte lower-case letters), and click [Login].

The CR-IR 391CL server application starts up and the initial window opens. When the server application has started up, the CR-IR 391CL server icon appears in the task tray in the bottom-right of the desktop screen.

IN000402.ai

Internet Explorer opens, and the User Selection window opens.

2.

Click the top, bottom, left, and then right edge portions of the Select a User. window in order.

IN000502.ai

The Study List window opens.

IN000501.ai

The Password input window for the password of the service engineer opens.
020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MU 3-1

Appx MU 3-2
4.
Select [Client Utilities].

5.

Click [User Settings (for Administrator)].


The User Settings (for Administrator) window opens.

V5.0 or before

IN000407.EPS

V1.1(B) or later

IN000527.ai

The Client Utilities Main menu opens.

IN000518.EPS

6.

Click [User Info Maintenance].


The User Info Maintenance (1) window opens.

IN000519.EPS

IN000517.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MU 3-2

Appx MU 3-3
7.
Click [Newly registered patient].
The User Info Maintenance (2) window opens.

14. Checkmark Automatically verify user. (


NOTE

).

Although you specify the user as an Automatically verify user. for the purpose of performing verification of the Automatic Output setting in the procedure described in this section, be sure to remove this checkmark after completion of the checkup work because the Automatically verify user. cannot be removed. For details on the Automatically verify user., see the CR-IR 391CL Operation Manual.

15. Click [Register].


The system returns to the User Info Maintenance (1) window.

16. Click [Close].


The system returns to the User Settings (for Administrator) window.
IN000520.EPS

17. Click [Close].


The system returns to the Main menu window.

8. 9.

Enter an account name. Enter User Name - For Image Display (up to 20 characters).

18. Click [Close].


The system returns to the Study List window.

10. Enter User Name - For Data Storage (up to 64 characters). 11. Under Authority, click [Down] and select Group 3. 12. Do not enter anything in New password and Confirm and leave
them blank.

NOTE
Entry in the Comment and Image sections in the window are optional.
For more information, see the Operation Manual.

13. Remove the checkmark from Automatically login user. (

).

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 3-3

Appx MU 3-4
Verifying the created user

2.

Click [OK].
The Select a User. window opens.

1.

In the CR-IR 391CL client, click [Log Off].

V5.0 or before

IN000408.EPS

V1.1(B) or later

IN000528.ai

IN000525.EPS

The confirmation dialog box opens.

3.

Make sure that the user you have created is being displayed.

IN000524.EPS

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MU 3-4

Appx MU 3-5
4.
In the Select a User. window, click the user you have registered.
The Password input window opens.

IN000526.EPS

5. 6.

Enter the password, and click [Login].


The Study List window opens.

Check to see that the Study List window opens, and then click [Changing users] to log off the system.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 3-5

Appx MU 3-6
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 3-6

Appx MU 3-7
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 3-7

Appx MU 3-8
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 3-8

Appx MU 4-1

Appendix 4 Settings for Automatic Output


To change the Automatic Output settings from their default values to some other values, follow the procedure described in this appendix.

Preparatory work
If the CR-IR 391CL has not been started:

NOTE
When changing any of the Automatic Output settings, obtain a confirmation from the user.

1.

Double-click the

icon on the desktop screen.

The CR-IR 391CL starts up, and then the Select a User. window opens.

2.

Click [Finish] in the bottom-left corner of the Select a User. window that opens.

If the CR-IR 391CL is up and running:

1.

Click [Close] in the upper-left corner of the Study List window.

REFERENCE
For V1.1(B) or later, click at the bottom of the Main Window.

IN000633.ai

The confirmation dialog opens.

IN000625.ai

2.
020-221-02E 01.08.2010 FM5563

Click [OK].
The client application exits.

CR-IR 391CL Service Manual

Appx MU 4-1

Appx MU 4-2
Starting the User Utility and making necessary settings

4.

1.

Right-click the CR-IR 391CL server icon in the task tray in the bottomright corner of the desktop screen.

Enter the username medicalservice and the password fieldengineer from the keyboard.

NOTES
The username and the password both must consist of single-byte lower-case letters only. They must not contain any space characters. The username medicalservice must always be typed in from the keyboard because that user is not added in the pull-down menu.

IN000402.ai

Its right-click menu opens.

2.

Click [User Utility].


The confirmation window opens.

MU000035.ai

5.
INApp0007.EPS

Click [OK].
The Main Menu window opens.

3.

Click [OK].
After the system terminates, the User Authentication - User Utility window opens.

IN000635.ai

INApp0008.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MU 4-2

Appx MU 4-3
6.
Click [Output Destination Settings].
The Setting destination for image output window opens.

9.

Specify the Timing of output.


Upon verification of a study : At the instant when the [Verify] button is clicked. Upon completion of an exposure : At the instant when the [Confirm] button is clicked, or at the time of switching over to the viewer window. In the case of outputting to the DVD and DICOM Transmission, the default is Upon verification of a study. Upon completion of an exposure cannot be selected. In the case of outputting on a printer, the default is Upon completion of an exposure. Either Upon verification of a study/Upon completion of an exposure can be selected.

10. Click [OK].


The Main Menu window opens.

11. For General-purpose file, repeat Steps 6 to 9.


INApp0009.ai

REFERENCES
The [Printer] tab is not displayed if the DICOM print option has not been installed. The [DICOM transmission] tab is not displayed if the DICOM transmission option has not installed.

12. Click [Finish].


A window opens to indicate that the system is in startup process.

NOTE
As for general-purpose files, specify the Naming rule of general-purpose image files here. see Setting the naming rule of general-purpose image files later in this appendix.

7. 8.

Checkmark Automatic image output (

).

INAppM0001.EPS

The system starts up, and the Select a User. window opens.

Check to see that the Destination for data transfer field shows the device name you have specified using the Service Utility.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 4-3

Appx MU 4-4
Setting the naming rule of general-purpose image files

1. 2.

Open the Setting destination for image output window. Click the General-purpose file tab.

INApp0010.ai

3. 4.

Click on

(down) beside the [Type] field.

A pull-down menu opens.

Select the format to set.


Setup value
Type0 Type1 Type2 Serial No. Ex.: Img0008.jpg Host name + Date + Serial No. Ex.: CVXXXXXXXX260004.jpg ID number + Study date + Anatomical region + Serial No. + Host name Ex.: 0123456789_051026_TEST_0006_CVXXXXXXXX.jp

Description

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 4-4

Appx MU 5-1

Appendix 5 Setup for Auto-verify


This section shows the procedures of making the following setting in order that a study for which exposure has been completed will be automatically verified. With this Auto-verify feature, outputting of images without user intervention to output destination equipment whose Automatic Output setting is enabled becomes possible.
See Appendix 4: Settings for Automatic Output in MU: Maintenance Utility.

Starting the User Utility and making necessary settings

1.

Right-click the CR-IR 391CL server icon in the task tray in the bottomright corner of the desktop screen.

IN000402.ai

Its right-click menu opens.

Preparatory work
If the CR-IR 391CL has not been started:

2.

Click [User Utility].


The confirmation window opens.

1. 2. 1.

Double-click the

icon on the desktop screen.

The CR-IR 391CL starts up, and then the User Selection window opens.

Click [Finish] in the bottom-left corner of the User Selection window.

If the CR-IR 391CL is up and running:


Click [Close] in the upper-left corner of the Study List window.
The confirmation dialog opens.
INApp0007.EPS

3.

Click [OK].
After the system terminates, the User Authentication - User Utility window opens.

IN000625 ai

2. 3.

Click [OK].
The Select Server Application Behavior window opens.
IN000635.ai

Select Exit and Click [OK].


The client application exits.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx MU 5-1

Appx MU 5-2
4.
Enter the username medicalservice and the password fieldengineer from the keyboard.

6.

Click [Auto-Determine Settings].


The Automatic verification of a study window opens.

NOTES
The username and the password both must consist of single-byte lower-case letters only. They must not contain any space characters. The username medicalservice must always be typed in from the keyboard because that user is not added in the pull-down menu.

INAppN0001.EPS MU000035.ai

5.

Click [OK].
The Main menu window opens.

7.

Checkmark Automatically verifying a study (

).

INAppN0002.EPS

INApp0008.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 5-2

Appx MU 5-3
8.
Auto-verify options become selectable. Checkmark the option to use, and click [OK].
A study is automatically verified at the time of completion of its exposure operation (or at the Completion of an exposure and its time of opening the viewer). verification take place simultaneously. The time until automatic verification can be set with Time required for automatic verification of a study. Study is verified after the set time followed by exposure. Selecting this option turns the Time required for automatic verification of a study field active so that you can set a value. The length of time until Auto-verify can be set in minutes (within a range from 5 to 720 minutes). The default is 30 min.

9.

Click [OK].
The system returns to the Main Menu window.

10. Click [Finish].


A window opens to indicate that the system is in startup process.

INAppM0001.EPS

The system starts up, and the Select a User. window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 5-3

Appx MU 5-4
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 5-4

Appx MU 6-1

Appendix 6 DICOM Tag Mapping Function


When generating image outputs using the DICOM CR STORAGE function, you can edit (copy, move, delete, or initialize) the tag information (image information). To edit the tag information, open the setup file (TagReplace.ini) and write desired data in the file. The procedure is described below:

TagReplace.ini file format


; Tag setup file ; [DICOM] ; ; 00080090=MOV-T-L,00092F90 00181400=CPY-T,00192F30 00192f90=DEL ; 00192F30=SET,SKULL,GENERAL

I. Comment II. Section name (protocol name) III. Editing destination tag IV. Command

NOTE
Do not use the TagReplace.ini file, which is used by any other equipment (such as the QA-WS), for the CR-IR 391CL. Due to different file storage format adopted, an error will result.

V. Initial value
FR000001.EPS

1. 2. 3.

Select Run... from the Start menu.


The Run... window opens.

I. II. III. IV. V.

Input C:\ProgramData\Fujifilm\Hobbit\Config and click [OK].


The Config folder opens.

Open the TagReplace.ini file with Notepad (Notepad.exe).

NOTE
By default, [DICOM] is described in the TagReplace.ini file. Do not delete this description,otherwise the CR-IR 391CL will not be started.

Comment Lines beginning with a semicolon (;) are handled as a comment. Section name (protocol name) As the section name, the protocol name targeted for tag information editing must be written within square brackets ([ ]). Only DICOM is supported. Editing destination tag Write the group number/element number of the editing destination tag information (enter a string of eight characters at all times). Command Write a tag information editing command. See the table that is presented later. Initial value Write a character string in VR-compliant format to specify the initial value for a tag information element.

4.

Write desired tag information in the file in accordance with the format described later.

REFERENCE
As the editing target tag VR, only character strings are supported. If a tag VR entry in the setup file is not a character string, an error dialog box opens at CR-IR 391CL startup.

5.

Save the TagReplace.ini file in UNICODE format and then close Notepad (Notepad.exe).

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 6-1

Appx MU 6-2
The following commands are available:
Command
Format

NOTES
Description

Process Copies an element from another tag.

When writing the TagReplace.ini file, set data in compliance with DICOM VR. Also, exercise care to avoid internal data inconsistency. Even if the editing destination tag differs from the source tag in VR, the editing process is performed as far as they are both in character string form. Note, however, that even if the character string length is over the limit specified by the editing destination tag VR, the tag information is set as is without being checked. The editing process will not be performed if the associated tag or element and initial value do not exist on the source side. For the detailed information about Fujis Private tags, see DICOM Conformance Statement.

CPY

Editing-destination-tag=CPY[-T],editing-source-tag -T : Performs an element copy operation after deleting spaces from the beginning and end of the source tag element. If, for instance, the source tag = ABC, the command copies ABC ( : space). Editing-destination-tag=MOV[-T][-L],source-tag -L : Performs a move operation after setting the source tag element length to zero. -T : Performs an element move operation after deleting spaces from the beginning and end of the source tag element. If, for instance, the source tag = ABC, the command moves ABC ( : space). Editing-destination-tag=DEL[-L] -L : Sets the element length of the editing destination tag to zero. Editing-destination-tag=SET, initial-value

Process Moves an element from another tag. Format

MOV

Process Deletes an element.

DEL SET

Format

Process Sets a fixed initial value for the element. Format

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 6-2

Appx MU 6-3
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 6-3

Appx MU 6-4
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 6-4

Appx MU 7-1

Appendix 7 Free Drawing Function Settings


The setting procedure for the free drawing function and setting file backup/restore is explained. The following settings can be changed. Pen size (3 types: narrow pen, medium pen, thick pen) Snapshot saving path Initial display screen at the time of start of the free drawing window (only for a dual-monitor configuration)

Snapshot saving path Change the path (= right side) of the following command in the [TEMP] section. tempSavePath = Snapshot saving path Enclose the specified path in double quotation marks (). Example: tempSavePath = C:\Temp

REFERENCE
The default set value is C:\Users\fujicr\AppData\Local\Temp\FDD. tempSavePath = %TEMP%

Initial display screen at the time of start of the free drawing window
This setting decides the monitor screen on which the free drawing window starts in an environment with a two-monitor configuration. Change the value (= right side) of the following command in the [FUNCTION] section. displayPosition = (0 or 1) Enter 0 for display on the primary monitor and 1 for display on the secondary monitor.

Procedure for changing the settings


Open the file C:\Program Files\FujiFilm\Hobbit\System\FDDSettingInfo.ini with Notepad and change the set values manually.

REFERENCE
The set values can be changed for server and clients. Pen size Three types (narrow pen, medium pen, thick pen) can be used for the free drawing pen size. Change the value (= right side) of the following commands in the [PENSIZE] section. PENSIZE1 (narrow pen) = (points) PENSIZE2 (medium pen) = (points) PENSIZE3 (thick pen) = (points)

REFERENCE
The default set value is 0 (primary monitor). displayPosition = 0

Setting file backup and restore


When reinstalling the server application/client application at the time of a version update etc., back up the following file before uninstalling the server application/ client application. C:\Program Files\FujiFilm\Hobbit\System\FDDSettingInfo.ini

REFERENCE
The default set values are narrow pen = 3 pt, medium pen = 9 pt, and thick pen = 27 pt. PENSIZE1 = 3 PENSIZE2 = 9 PENSIZE3 = 27

NOTE
FDDSettingInfo.ini is the setting file for the free drawing function. In an environment with a dual-monitor configuration, it is possible that this setting file has been edited. After reinstallation of the server application/client application, use the backed-up FDDSettingInfo.ini to overwrite.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 7-1

Appx MU 7-2
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 7-2

Appx MU 7-3
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 7-3

Appx MU 7-4
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx MU 7-4

SP-I

CR-IR 391CL Service Manual

SP: Service Parts

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

SP-I

SP: Service Parts

SP-II
Reason
New release (FM5535) All pages

Control Sheet
Issue date
04/28/2009

Revision number
01

Pages affected

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

SP-II

SP-1

1. Service Parts List


1.1 How to Use Service Parts List
RANK
Parts handling ID symbols used to identify the parts requiring special operation The ID symbols are assigned to applicable parts. Parts without the R mark are replaced and handled in a regular manner.
Symbol
R Q, T

REF. NO.

A number for indicating each part in the Service Parts Exploded Views.

PART NUMBER

A code number that is unique to each part. The rightmost letter of the code number has the following meaning.

For hardware The letter denotes the version number of a part. If parts have different version numbers, they are upward-compatible. For software The letter denotes the software specifications.

Description
Repairable parts Symbol for use other than in Japan

Export regulation mark This + mark is assigned to the parts subject to Export regulations. Parts without the + mark are not subject to Export regulations.
Symbol
+

PART NAME QTY.

This represents the general name of a part.

Description
Parts subject to Export regulations

QTY. represents the quantity of parts used in a unit or assembly.

Fault rankings used for estimating the recommended stock quantity All parts are assigned a symbol letter from A to E.
Symbol
A B C D E

REMARKS

Description
Consumable parts or parts that will be replaced at short intervals Parts that may become faulty accidentally and have a relatively high failure rate Parts that have a sufficiently long MTBF, but are expected to have a high failure rate Parts that have a sufficiently long MTBF, but are expected to become faulty Parts that are necessary for fault analysis or parts that may be needed in case of faults such as man-induced damage

Unique name of a part or its relevant information or note is described in this column.

SERIAL NUMBER

The units may contain different parts depending on their shipment control number. SERIAL NUMBER indicates the shipment control number to which the parts are applicable. If this column is blank, the parts are applicable to all the relevant units.

RANK column description The symbols for Fault Ranking, Parts Handling, and Export regulation are assigned in order named. Thus, one to three letters are put in the RANK column.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

SP-1

SP-2
Recommended quantities of spare parts
It is recommended as a rough guide to hold in stock a specified quantity of parts according to the rank (A to E) assigned to the parts. Parts to be replaced at periodic intervals must be held in stock separately. Adjust the quantity of parts stock depending on the number of working units (N) as prescribed below. Q: Quantity used in a single system N = 1 Rank A = 1 + Q 0.3 Rank C = 1 + Q 0.05 Rank D = 1 + Q 0.02 2 N 10 Rank A = 2 + N Q 0.3 Rank C = 2 + N Q 0.05 Rank D = 1 + N Q 0.02 11 N 300 Rank A = 3 + N Q 0.3 Rank C = 3 + N Q 0.05 Rank D = 2 + N Q 0.02

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

SP-2

SP-3 1.2 Service Parts List


No relevant item.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

SP-3

SP-4
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

SP-4

SP-5
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

SP-5

SP-6
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

SP-6

PM-I

CR-IR 391CL Service Manual

PM: Preventive Maintenance

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-I

PM: Preventive Maintenance

PM-II
Reason
New release (FM5535) All pages

Control Sheet
Issue date
04/28/2009

Revision number
01

Pages affected

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-II

PM-1

1. Preventive Maintenance Items


While the CR-IR 391CL is being used, maintenance of the items listed in the table on the right should be performed periodically while observing the warnings and cautions set forth below.

List of preventive maintenance items


Reference section
2.1 3. Safety 3.1 3.2 4.1 Service Voltage Power Plug/Multi-Outlet Power Strip PC Internal Cleaning LCD Cleaning Conducting the Dell Diagnostics Express Test Confirmation of Image Input to Storage onto DVD Image Output to Film Backup of Setup Files and Log Files Verification of Date and Time [Option]

Maintenance item

Required time

Replacement part

Remarks

2. Checking for a Fatal Error Confirming the Event Log

WARNING
To avoid electrical shock, turn OFF the equipment power before performing maintenance work.

4. Hardware Cleaning 4.2

WARNING/CAUTION
Observe the warnings and cautions set forth in the chapter titled Safety Precautions.

5. Executing the Error Analysis Tool (Dell Diagnostics) 5.1

CAUTION
When servicing the inside of the PC, be sure to wear an antistatic wristband to ground your body. If your body is not grounded, the static buildup on your body may damage electronic parts on the circuit boards.

6. Functional Checks 6.1 6.2 7.1 7.2

7. Backup of Settings and Verification of Date and Time

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-1

PM-2

2. Checking for a Fatal Error


2.1 Confirming the Event Log
View the OS event log (application) to check for any fatal error recording.
For the procedure for viewing the event log, see 2. Using the Event Viewer under MT: Machine Troubleshooting.

3. Safety
3.1 Service Voltage
Verify the service voltage that is available within the institution.

NOTE
The CR-IR 391CL system has a backup notification function. By default, this function prompts the user at 7-day intervals to perform periodic backup in preparation for a failure. Therefore, the following message may appear when the application is started during an installation, inspection, or other process:

3.2 Power Plug/Multi-Outlet Power Strip


WARNING
When making resistance measurements, be sure that the power plug is disconnected from an outlet. Measure the resistance values of the power cable and multi-outlet power strip.
Terminals
Resistance value

Between L and N
100 k or higher

Between L and E

Between N and E

<For Japan> E L

<For U.S.> E L N

<For European and other countries> E N L

<For U.K. and other countries> E N L


FRCH616003.ai

IN000433.ai

A backup procedure is to be performed at the end of an installation or inspection process. Therefore, even when the above message appears, do not perform the backup procedure immediately. Click [Cancel] and continue to sequentially perform the steps set forth in the service manual. Be sure to acquire a backup log with specified timing because it is necessary, for instance, to store a log of operational checks performed for installation or inspection and delete the event log.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-2

PM-3

4. Hardware Cleaning [reference]


4.1 PC Internal Cleaning
Cooling fans (power supply fan, CPU fan, etc.) are mounted in the PC to dissipate generated heat through air convection. If dust is heavily accumulated in the neighborhood of a cooling fan or a vent in the PC housing, the effect of the cooling fan may decrease, thereby adversely affecting the operation of the PC. It is therefore necessary to clean the inside of the PC on a periodic basis.

2.

As shown in the figures, push up the stopper and open the PC housing.

PM000403.EPS

PM000404.EPS

Preparations
Disconnect all cables from the PC main body.

3.

With an air blower, clean the heat sink and circuit board section.

Cleaning

1.

With a brush attached to a vacuum cleaner, carefully vacuum-clean the slots and other openings in the rear of the PC.

PM000405.EPS

PM000401.EPS

PM000402.EPS

An intake fan is mounted at the front of the DELL OptiPlex 755. This intake fan directly blows air onto the heat sink that is installed above the CPU. Therefore, apply a vacuum cleaner to the front of the PC body to remove dust from the intake fan, and use an air blower to blow air from the inside of the PC main body to the outside and remove dust from the heat sink.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-3

PM-4
4.
If dust is heavily accumulated on the heat sink section, remove the heat sink and clean it.

4.2 LCD Cleaning


CAUTION
At the time of periodic maintenance, confirm that the caution label has not come off. If it has come off, attach a new label. Also attach a new label when the monitor with the caution label has been replaced for repair.

CAUTION
If silicone oil is not on hand, do not remove the heat sink. Silicone oil is applied to the junction between the heat sink and CPU. When the heat sink is removed from the CPU for cleaning purposes, wipe off the silicone oil, clean the heat sink, and then apply new silicone oil. Removing the heat sink

1.

With a Cleaner Torch, remove dust from the LCD.

PM000406.EPS

PM000407.EPS

PM000414.EPS

2.

If there is any stubborn dirt on the LCD panel surface, wipe it clean with a cloth (e.g., gauze) well wrung out in water.

CAUTION
PM000408.EPS PM000409.EPS

5. 6.

Mount the heat sink back and then close the PC housing cover. After completion of cleaning, perform an operational check of the cooling fans as directed under 5. Executing the Failure Analysis Tool (Dell Diagnostics) (the Express Test includes a cooling fan operational check).

If you vigorously scrub the LCD panel surface, the liquid crystal surface may become damaged. Therefore, do not apply any undue force to the LCD panel surface when you wipe it clean. If the LCD panel surface is heavily soiled and cannot be cleaned with a moistened cloth, clean it with the monitor cleaner kit. The monitor cleaner kit is of a chemical type. Therefore, if the monitor cleaner kit is repeatedly used for cleaning purposes, the LCD panel surface will be adversely affected. When using the monitor cleaner kit, read its instruction manual and exercise utmost care.

NOTE
Do not use dehydrated ethanol for cleaning purposes because it adversely affects the LCDs surface film.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-4

PM-5

5. Executing the Error Analysis Tool (Dell Diagnostics)


5.1 Conducting the Dell Diagnostics Express Test
See the following and conduct the test.
See 4.8.1 Running the Dell Diagnostics Express Test under MT: Machine Troubleshooting.

6. Functional Checks
6.1 Confirmation of Image Input to Storage onto DVD
See the following and perform the specified procedure.
See 5.3 Checking Every Step from the Inputting of Images to the Saving of Images onto DVD under IN: Installation.

6.2 Image Output to Film


See the following and perform the specified procedure.
See 5.4 Checking Output Images (option) under IN: Installation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-5

PM-6

7. Backup of Settings and Verification of Date and Time


7.1 Backup of Setup Files and Log Files
This section describes the procedure for backing up patient information, setup information, and log information.

2. 3.

Click [Eject].
The DVD drive tray opens.

Remove the disk.

NOTE
Attach a label to the case, mark it as a Image storage disk, and write the date on the label.

Preparations
Make sure that all images are written on a storage disk. Attach a label to the case of a backup disk, write a date on the label, and mark it as a Backup disk.

4. 5.

Close the empty tray. Click [Update].


Only Device Name is displayed. Status, Usage, and Disk Write are hidden.

Removing the disk


Remove the storage disk as directed below.

1.

Click

in the upper right corner of the Study List window.

The Indicator window (Disk) opens.

MUApp0002.ai

IN000620.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-6

PM-7
6.
Click [OK].
The system returns to the Study List window.

Starting the Backup Utility

1.

Right-click the CR-IR 391CL server icon in the task tray, which is located in the lower right corner of the desktop screen.

IN000402.ai

The right-click menu opens.

2.

Click Backup Utility.


A confirmation window opens.

IN000624.ai

MU000034.ai

7.

Click [Close] in the upper left corner of the Study List window.
The [20339] Application will be terminated. +Are you sure? dialog box opens.

3.

Click [OK].
After the system is shut down, the User authentication window opens.

MU000035.ai IN000625.ai

8.

Click [OK].
The system returns to the desktop screen.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-7

PM-8
4.
From the keyboard, enter the username medicalservice and the password fieldengineer.

6.

Click [Backup].
The Backup window opens.

NOTES
The username and password both consist of 1-byte lower-case characters only. Do not include any space. Since the medicalservice user is not registered in the pull-down menu, be sure to enter the username from the keyboard.

IN000626.ai

7.
MC000098.ai

Put a checkmark on each of the following items (


Patient information Setup information Log information Delete logs after completing backup processing

).

5.

Click [OK].
The Main Menu window opens.

8. 9.

Click [Start].
The Select folder window opens.

Open the DVD drive tray, and insert the backup disk into the tray.

MU000036.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-8

PM-9
10. Complete the following checks and then click [OK].
I.

11. Click [OK].


The disk formatting confirmation window opens.

IN000627.ai

I.

Check that the current drive is D:. Also, check that the folder name represents the execution date and time (YYYYMMDDhhmmss).
MUApp0004.ai

The log information deletion confirmation window opens.

NOTE
If you insert a formatted disk at this step, the above disk formatting confirmation window does not open; however, the following message appears. Click [OK] in response to the message because the backup process remains unaffected.

MUApp0003.ai

MU000040.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-9

PM-10
12. Click [OK].
The backup destination folder creation confirmation window opens.

Post-backup confirmation

1.

From My Computer on the [Start] menu, open drive D: (DVD drive) and verify that the files are stored.

IN000628.ai

13. Click [OK].


Upon completion of backup processing, the completion window opens.

IN000629.ai

2.
MU000042.ai

Remove the backup disk from the DVD drive, and then insert the Image storage disk. Double-click desktop.
The log-in window opens.

14. Click [OK].


The system returns to the Main Menu window.

3.

, which is displayed in the upper left corner of the

15. Click [Finish].


The system returns to the desktop window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-10

PM-11
4.
Log in as fieldengineer.
The Study List window opens. For the procedure for logging in as fieldengineer, see 5.3 Checking Every Step from the Inputting of Images to the Saving of Images onto DVD under IN: Installation.

9.

Click [OK].
The system returns to the Study List window.

10. Click [Close] in the upper left corner of the Study List window.
The [20339] Application will be terminated. +Are you sure? dialog box opens.

5. 6.

Click All studies under Disk. Verify that the list on the storage disk is displayed.

IN000625.ai

11. Click [OK].


IN000630.ai

The system returns to the desktop screen.

7. 8.

Click

in the indicator section.

The Indicator window opens.

Verify that no error information is recorded as an event.

IN000631.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-11

PM-12 7.2 Verification of Date and Time


Verify the date and time from Setting PC (OS) date/time, which is included in the Simplified setup wizard of the Service Utility.
See 5.2 Setting the Date and Time under MU: Maintenance Utility.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-12

PM-13
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-13

PM-14
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PM-14

IN-I

CR-IR 391CL Service Manual

IN: Installation

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-I

IN: Installation

IN-II
Revision number
01 02

Control Sheet
Issue date
04/28/2009 01/08/2010

Reason
New release (FM5535) Revision for software V1.1(B) (FM5563)

Pages affected
All pages 1, 2, 5, 6, 8, 12, 15, 17, 27, 29 to 32, 42, 44, 47, 53, 68, 70, 71, 75, 76, 81

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-II

IN-1

1. CR-IR 391CL Installation Conditions


This section states the PC (controller) and monitor installation conditions.

1.3 Places of Installation


Environmental conditions
Avoid installing the machine at the following places: Places where the temperature changes drastically Places near heaters or other heat sources Places where the machine is likely to be wet or submerged Places where the machine is likely to come into contact with any corrosive gas Dusty or dirty places Places where the machine is subjected to constant vibration or shock Places where the machine is subjected to excessive vibration or shock Places exposed to direct sunlight Also, be sure that the monitor is not installed at the following places: Places where the monitor is surrounded, such as in a rack case Places whether the display surface is exposed to direct sunlight Places near a transformer, another monitor, a power line, or a 0.02 Gauss or more of AC magnetic field

u NOTE u
Listed below are the abbreviations adopted in this chapter. : Application : Application key : Reader Unit RU configuration data : : RU application RU maintenance utility : AP AP key RU RU-Config RU-AP RU PC-TOOL

For the dimensions and weights of the monitor and peripherals, see the respective manuals that are supplied with them.

1.1 Dimensions and Weight


Dimensions (width height depth)
PC Monitor OptiPlex 760 OptiPlex 780 399 114 353 (mm) 399 114 353 (mm)

Weight
Approx. 10.4 kg Approx. 8.3 kg Approx. 9.6 kg Approx. 4.63 kg Approx. 5.6 kg

S2031W-HBK 427 to 509 469 208.5 (mm) DELL E170S 374.7 380.6 140 (mm) S1721-SHBK 362 280 to 406 200 (mm)

1.2 Temperature and Humidity


Condition Operating Non-operating Temperature 10C to 35C -20C to 60C Humidity 30% to 80% RH (non-condensing) 30% to 80% RH (non-condensing)

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-1

IN-2 1.4 Power Requirements


Frequency
PC 50Hz/60Hz S2031W-HBK 50Hz/60Hz Monitor DELL E170S S1721-SHBK 50Hz/60Hz 50Hz/60Hz

1.5 Grounding
Input voltage Max. input current
4.0A/2.0A 0.7A 1.5A 0.65A/0.4A

AC115 to 230V AC100V to 120V AC200V to 240V AC100V to 120V AC200V to 240V AC100V to 120V AC200V to 240V

Connect power cables appropriately following the local standards, rules and regulations applicable to grounding.

Phase : Single phase Power frequency : 50/60 Hz

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-2

IN-3

2. Installation Procedure Overview


IMPORTANT
Be sure that the following equipment is completely installed and set up. RU See Chapters 1 to 11 of Installation of the RU Service Manual. Other equipment (such as a film printer) See the installation instructions set forth in the respective Service Manuals.

1. Hardware setup Check the supplied component items, install the CR-IR 391CL accessories, and make cable connections to the RU.

2. Making a cable connection to other equipment Connect a film printer.

IMPORTANT
Have on hand a CD-R disk that stores the CR-IR 391CLs AP key (114Y2129002A), which is distributed for use in servicing.

3. Making CR-IR 391CL software settings along with option settings Make necessary software settings using the Service Utility, along with a software setup on the film printer.

4. Performing checks for proper operation Check for proper operation from image input to image loading. Check output images. Make a backup copy of the configuration file. View and delete the error log.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-3

IN-4

3. CR-IR 391CL Hardware Setup


3.1 Unloading and Unpacking

3.1 Unloading and Unpacking


Remove the following items from the packing box. PC (controller) Monitor Others (options, etc.)

3.2 Checking the Component Items

CAUTIONS
3.3 Installing the Accessories and Optional Install the monitor, insulating Items transformer (only for units used in Japan), keyboard, and mouse. 3.4 Connecting a Cable Between the RU and Other Equipment When unloading, transferring, and unpacking the machine, observe the following precautions: Do not subject the machine to vibration or shock. If the machine is unduly vibrated or shocked while it is unloaded or transferred, it may become damaged or defective. Avoid moisture condensation inside the machine. If the machine is subjected to a drastic temperature change when it is transferred or unpacked, moisture condensation may occur inside the machine. If you turn ON the machine while moisture is condensed on its inner surface, the machine may become defective. To avoid such a problem, be sure to allow the machine to stand at a room temperature for a period of 1 hour or longer and then turn ON the power.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-4

IN-5 3.2 Checking the Component Items


Check that the following component items are fully supplied.

Monitor
Contained in the carton of LCD display
Item
Monitor Monitor cable Power cable

Qty
1 1 1

PC
PC box
Item
PC Keyboard Mouse Power cable Power conversion connector Application Software Windows reinstallation CD DELL driver installation CD Information sheet (Dell desktop PC) Standard Kit EXP Quick Guide Operation Manual (Operation Manual/Software License Agreement) Reference Guide CD

Qty
1 1 1 1 1 1 1 1 1 1 1 1 1

For details of the component items, see 1.1 Product Code under Product Specifications.

Others (separately packed items, options, etc.)


Item
MFP Key Software DICOM Print Key Software DICOM Standard CR Storage Key Software Free Layout Print Key Software DICOM ID MWM Key Software *1 O: Option

Product code
IR 391 MFP E IR 391 DICOM PRINT E IR 391 DICOM STORAGE E IR 391 F-LAYOUT PRINT E IR 391 DICOM ID MWM E

Qty
1 1 1 1 1

Remarks*1
O O O O O

For details of the component items, see 1.1 Product Code under Product Specifications.

For details of the component items, see 1.2 Optional Components under Product Specifications.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-5

IN-6 3.3 Installing the Accessories and Optional Items


Connect the insulating transformer (only for units used in Japan), keyboard, mouse and monitor to the PC as illustrated below:

3.3.2 Monitor
The following monitors can be connected to CR-IR 391CL. 17 inch LCD monitor (Nanao S1721-SHBK) 17 inch LCD monitor (DELL E170S) 20 inch LCD monitor (Nanao S2031W-HBK)

3.3.1 Keyboard, Mouse, and Power Cable


CAUTIONS
For a PC provided with the source voltage changeover switch (between 115 and 230 VAC), set the PC source voltage according to the voltage supplied to the institution concerned and then connect the power cable to the power source. Do not bind or tie down the AC power cable such that strain will be placed on it.

Installation of the LCD


LCD panel installation

1.

Take the LCD panel out of its carton and install it in a place of use.

NOTE
Place the LCD panel on a level surface.

GOOD

NG
FR1H1921.EPS

Making VGA cable and AC power cable connections

1.

Connect the VGA cable and the AC power cable.


For information on how to connect the VGA cable and the AC power cable, see the LCD panel operation manual.

1.

Connect the keyboard, mouse, and power cable to the PC.


For details on the connection procedures, see the documentation supplied with the PC.

3.3.3 Film Printer Hardware Setup (option)


Connect a film printer as follows.

2.

Connect the power cable to the power source.

1.

Connect the AC power cable.


For information on how to connect the AC power cable, see the film printers operation manual.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-6

IN-7 3.4 Connecting a Cable Between the RU and Other Equipment


Connect the RU and other equipment to the CR-IR 391CL via network cables.

3.4.1 Making a Cable Connection to the RU

1.

Connect the AC power cable.


For information on how to connect the AC power cable, see the RUs operation manual.

NOTE
To connect the CR-IR 391CL to the RU, use the following network cable. The UTP type which is compliant with category 5 or more should be used. IEC950/UL1950-compliant cables should be used.

2.

Make connections to the LAN using network cables.


For information on how to make network cable connections, see IN: Installation of the RU Service Manual.

REFERENCE
The RUs cable connector is found in the lower portion of the right-hand side of the RU main unit.

For the network type RU operation


With 100BASE-TX (straight) cables, connect the RU to the CR-IR 391CL via a hub.
100BASE-TX cable (straight) CR-IR 391CL HUB 100BASE-TX cable (straight) RU Other connected hosts (Film printer)
00000028.EPS

3.4.2 Film Printer Cable Connection (option)

1.

Using a network cable, connect the film printer to the LAN.


In the case of DRYPIX 1000/3000
See IN: Installation of the DRYPIX 1000/3000 Service Manual.

100BASE-TX cable (straight)

In the case of DRYPIX 2000


See IN: Installation of the DRYPIX 2000 Service Manual.

In the case of DRYPIX 4000


See IN: Installation of the DRYPIX 4000 Service Manual.

In the case of DRYPIX 7000


See IN: Installation of the DRYPIX 7000 Service Manual.

In the case of DRYPIX PRIMA


See IN: Installation of the DRYPIX PRIMA Service Manual.

NOTES
Do not connect a telephone line to the network connector of the CR-IR 391CL nor to that of other equipment. For the above-mentioned equipment (the CR-IR 391CL and DRYPIX), IEC950/ UL1950-compliant cables should be used.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-7

IN-8

4. Software Setup
4.1 Setting the Regional and Language Options

4.1 Setting the Regional and Language Options


Prior to performing necessary settings using the Service Utility functions, perform OS settings according to the region where the equipment is to be installed.

1. 2.

Turn ON the PC power.


Windows Vista starts up. After about one minute, the CR-IR 391CL starts.

4.2 Changing the Displayed Language and Replacing the Menu Database

When the initial window opens, sequentially click its upper left and upper right corners within a period of 2 to 3 seconds.
Click the upper left corner first, and then the upper right corner.

4.3 Option Key / AP Key Installation

4.4 Setup by the Simplified Setup Wizard Performing preparatory operations (such as the reinstallation of option keys and AP keys) that are required to start up the CR-IR 391CL. 4.5 RU Settings

00000118.ai

The ServiceUtilityAuthentication window opens.

4.6 Film Printer Software Setup (option)

Operation to be performed as required

MU00001 .ai

3.
4.7 Checking Connections with Other Equipment Checking connections with other pieces of equipment (Host equipment and DICOM equipment)

Click [Cancel].
The System return to the desktop screen.

4.

Select [Control Panel] from the

menu.

The Control Panel window opens. If the window is not in the Classic View mode, click [Classic View] to change the display to Classic View.

5.
020-221-02E 01.08.2010 FM5563

Double-click [Regional and Language Options].

CR-IR 391CL Service Manual

IN-8

IN-9
The [Regional and Language Options] window opens.

7. 8.

Click [Customize this format].


The [Customize Regional Options] window then opens.

Select the Date tab.

IN000433.ai

6.

Click the Formats tab to select a language (region) to use from the pull-down menu in Current format.
N000434 ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-9

IN-10
9.
Following examples shown in the table below, enter a date from the keyboard in the [Short date] box of the [Date formats] field.

12. Select the Time tab.

CAUTION
A date entered will not be displayed correctly if the order to display year/ month/day used in the CR-IR 391CL system is different from that of the OS date format. Because this is used for important information, including the date of study and the like, it is essential to perform a date setting on the OS side carefully at this step. For details of settings of the date format used in the CR-IR 391CL system, see 4.4.4 System Settings.
Date format used in the CR-IR 391CL
Japanese date (S62.10.07) ANSI long date (1987.OCT.07) ANSI short date (1987.10.07) American long date (OCT.07.1987) American short date (10.07.1987) European long date (07.OCT.1987) European short date (07.10.1987)

Date format used in the OS short Date format


yy/MM/dd yyyy/MM/dd yyyy/MM/dd MM/dd/yyyy MM/dd/yyyy dd/MM/yyyy dd/MM/yyyy
MU000404.ai

* Enter directly from the keyboard because some formats are not displayed in the pull-down menu.

13. Select [HH:mm:ss] or [H:mm:ss] for the [Time format:] box setting.
CAUTION
Do not use tt representation. The CR-IR 391CL database will not be displayed correctly if [hh:mm:ss tt] or [h:mm:ss tt] is specified for the time format.

10. Similarly, perform settings for the [Long date] box.


NOTE
When doing so, observe the order of entering year/month/day in the short date format determined at Step 6 above.

11. Click [Apply].

14. Click [OK].


The system returns to the [Regional and Language Options] window.

15. Click [OK].


The system returns to the Control Panel.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-10

IN-11
Defining the character to be used as a decimal point
Select . (period) as the character to be used as a decimal point. If anything other than a period is selected, an error occurs when you select an image distribution destination with the QA function.

3.

1.

Check to see that the character specified in the Decimal symbol field is . (period). If not, change it to . (period). If, as a result of the above selection, the same symbol is selected for the Digit grouping symbol and Decimal symbol fields, change the symbol for the Digit grouping symbol field.

In the Control Panel window, double-click Regional and Language Options.


The Regional and Language Options window opens.

2.

Make sure that the Formats tab is selected and click [Customize this format].

RI000228.ai

The Customize Regional Options window opens.


RI000226.ai

4. 5.

Click [OK].
The system returns to the Regional and Language Options window.

Click [OK].
The system returns to the Control Panel.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-11

IN-12 4.2 Changing the Displayed Language and Replacing the Menu Database
In the CR-IR 391CL system, English (not in USA) version menus and parameters have been installed as the default values. Replace the menu database and parameter files according to the place of delivery of this system.

3.

Double-click DVD RW drive (D:).

NOTE
Change the displayed language first and then perform necessary settings. Changing the displayed language causes the settings performed in the Service Utility or User Utility to be lost, initializing the system settings to the default values determined individually for each country.
IN000442.ai

The installation launcher starts.

1. 2.

Insert the CR-IR 391CL Application Software CD into the DVD drive. Select [Computer] form the
The Computer window opens.

menu.

(Vx.x represents a version number.)

INAppL0001.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-12

IN-13
4.
Click .

6.

Select Color and click [Next].


The confirmation window opens.

A window opens, where a desired language is to be selected.

N000438.ai

IN000436.ai

5.

On the window that opens, select a language to be installed and then click [Next].
A window opens, where a monitor type is to be selected.

7.

Check the selected Language and Monitor Type and then click [Yes]. To change a selected value, click [No] to return to the previous window.
Setup file installation processing will then start. After the completion of the installation processing, the system returns to the installation launcher top window.

8.

Click

A window opens, where a desired language is to be selected.

IN000437.ai

IN000439.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-13

IN-14
9.
Select the language for study menus to be installed and click [Next].
[Do you want to use FNC (Flexible Noise Control Processing)?] is displayed.

IN000440.ai

10. Select ON (Software Options required) and click [Next].


The confirmation window opens.

IN000441.ai

11. Check the values selected for Language and FNC and click [Yes].
To change the selected value, click [No] to return to the previous window.
Parameter file installation processing will then start. After the completion of the installation processing, the system returns to the installation launcher top window.

12. Click [Finish].


020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-14

IN-15 4.3 Option Key / AP Key Installation


4.3.1 Option Key Installation
The following option keys are available. Install necessary option keys in compliance with the CR-IR 391CL installation specifications.
Function
Image processing Image input/output Print output Patient information

The installation procedure is described below.The same installation procedure applies to all the option keys.

1. 2.

Insert an option key CD into the DVD drive. Select Computer from the DVD RW drive (D:).
The installation start window opens.
The indication varies with the option key for installation.

menu and double-click

Product code
IR 391 MFP E IR 391 DICOM STORAGE E IR 391 DICOM PRINT E IR 391 F-LAYOUT PRINT E IR 391 DICOM ID MWM E

Description
MFP image processing DICOM-based image transmission functions available DICOM print function Free layout print function DICOM MWM Patient information

IN000443.ai

3.

Click [Continue].
A window opens to indicate the completion of installation.
The indication varies with the option key for installation.

IN000444.ai

4. 5. 6.

Click [OK].
The system returns to the desktop screen.

Remove the CD from the DVD drive. To install other option key, change the CD and repeat steps 2 through 5.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-15

IN-16
4.3.2 AP Key Installation
NOTE
Install the AP key after all option keys have been installed. This is because once an option key has been installed, the AP key is invalidated requiring thus the AP key to be reinstalled. Install the AP key as follows:

1. 2.

Insert an option key CD into the DVD drive. Select Computer from the DVD RW drive (D:).
The installation start window opens.

menu and double-click

IN000445.ai

3.

Click [Continue].
A window opens to indicate the completion of installation.

IN000446.ai

4. 5.

Click [OK].
The system returns to the desktop screen.

Remove the CD from the DVD drive.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-16

IN-17 4.4 Setup by the Simplified Setup Wizard


Using the simplified setup wizard of the Service Utility, settings that are required for installation are made.

4.

Perform the following:

4.4.1 Startup of the Service Utility

1.

Make sure that there is no icon representing the CR-IR 391CL server on the task tray. If the icon is present (meaning that the CR-IR 391CL server is up and running), right-click the icon and select Exit
For details, see 6.4 Turning OFF the CR-IR 391CL and RU.

I.

II.
IN000416.ai

2.

On the desktop screen, double-click


The CR-IR 391CL starts up.

I. Enter the password fieldengineer. II. Click [OK]. The Service Utility starts up and the Service Utility top window opens.

3.

Within 2 to 3 seconds of the appearance of the initial window, sequentially click its upper left and upper right corners.
Click the upper left corner first, and then the upper right corner.

00000118.ai

The ServiceUtilityAuthentication window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-17

IN-18
4.4.2 Starting the Simplified Setup Wizard

1.

Click [Simplified setup wizard] on the Service Utility top window.

Click

IN000409.ai

The Setting PC (OS) date/time window of the Simplified setup wizard opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-18

IN-19
4.4.3 Setting the Date and Time

1. 2.

Click [Date/time change].


The Date and Time window opens.

Verify the date, time and time zone.

NOTE
Carefully check the date and time because they are important values for the study date and exposure time.

If the shown Date, Time and Time zone value is not correct, change it as appropriate and click [Apply].

MU000502.ai

00000115.ai

3. 4.

Click [OK].
The system returns to the Setting PC (OS) date/time window.

Click [Next].
The System settings window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-19

IN-20
4.4.4 System Settings
Use the System settings window to perform setup concerning the Institution name, date/time format, and patient name format (multi-byte), and the like.

1. 2.

Enter Institution name represented by single-byte alphanumerics. Click the downward arrow mark ( select it. ) for Year/month/day format to

CAUTION
If you have changed the year/month/day format, be sure to change the setting of the OS short date format as well. For details of the necessary setting, see 4.1 Setting the Regional and Language Options.
Setting
Japanese date (S62.10.07) ANSI short date (1987.10.07) American long date (OCT.07.1987) American short date (10.07.1987) European long date (07.OCT.1987) European short date (07.10.1987) Year+YY.MM.DD YYYY.MONTH.DD YYYY.MM.DD MONTH.DD.YYYY MM.DD.YYYY DD.MONTH.YYYY DD.MM.YYYY ANSI long date (1987.OCT.07)

Meaning

: Default

3.

Click the downward arrow mark ( select a time format.


Setting
HH:MM:SS AM

) for Time format, and then


Meaning
12-hour format 24-hour format

MU000503.ai

HH:MM:SS : Default

4. 5.

Ensure that the [Inputting a patient name by multi-byte characters] check box is not checkmarked. Click [Next].
The [Setting the Server Equipment] window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-20

IN-21
4.4.5 Server Equipment Settings
Use the Server Equipment Settings window to perform setup concerning the CRIR 391CL server equipment name, software keyboard, monitor, and the like.

4.

Click [Selection] under Monitor model.

IMPORTANT
For a locally procured LCD monitor, be sure to perform the procedure below: I. Insert a media (compatible with Windows file system such as FD, CD) where the LUT file is stored into the media drive.

II. Click Update on the Monitor model selection window. III. Select an LUT for the added model and click [OK].
The Monitor model selection window opens.

MU000505.ai

For details on monitor models, see 6.2.2 Monitor Settings under MU: Maintenance Utility.
MU000504 ai

1. 2.

Enter the Equipment name (host name). Verify that CVXXXXXXXX is entered as the Host name and that 172.16.1.20 is entered as the IP address.
(NOTE: The XXXXXXXX portion represents an 8-digit serial number.)

5.

Select a monitor model and then click [OK].


The system returns to the [Setting the Server Equipment] window.

NOTE
The monitor settings are automatically entered. Although the Magnified Display (%) setting can be changed, do not change it now.
For details, see 6.2.2 Monitor Settings under MU: Maintenance Utility.

3.

To use the software keyboard, put a checkmark in the Use check box under ( ).

6.

Next, perform the following setup steps (DICOM and disk drive settings).

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-21

IN-22
Set up DICOM (Media Storage setting)
The procedure for setting information for this equipment concerning DICOM Media Storage is described below. DICOM Media Storage is used for image transfer to a DVD.

2. 3.

Enter an AE name (e.g., MEDIA) in the AE Name field under Media Storage setting. Click the downward arrow mark ( ) for Maximum pixel density size for a stored image, and then select a maximum pixel density size for a stored image.
Setting
ST HQ : Default Standard density High density

1.

Click [DICOM setting].


The Set up DICOM window opens.

Description

REFERENCE
Selecting HQ decreases the number of images that can be recorded on a DVD.
For the number of images that can be stored when the ST, HQ, compressed, or uncompressed option is selected, see under 1.6 Image Storage Performance of Product Specifications.

4.

Click the downward arrow mark ( ) for Whether or not to specify data compression for stored images, and then select a stored image compression option.
Setting
Compressed Uncompressed : Default

Description
Compresses the image (lossless). Leaves the image uncompressed.

MU050007.ai

REFERENCE
The following items shown within the fame on the window above appear only when the respective options are installed. Print SCU settings : Free Layout Print option
See 4.6 Film Printer Software Setup (option). See Appendix 1: Settings for Saving Images into DICOM Storage Equipment in Appx IN: Installation Appendix.

REFERENCE
Selecting Uncompressed decreases the number of images that can be recorded on a DVD.
For the number of images that can be stored when the ST, HQ, compressed, or uncompressed option is selected, see under 1.6 Image Storage Performance of Product Specifications.

Settings for Storage SCU : DICOM Storage option

5.

When storing two-byte character (Kanji or other multi-byte character) information, put a checkmark in the Multi-byte character setup check box under ( ).

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-22

IN-23
Set up DICOM (Print SCU setting) (option)
The procedure for setting information for this equipment concerning DICOM Print is described below.

4.

Put a checkmark in both the BasicGrayscalePrint and Verification check boxes under Presentation Context ( ).

REFERENCE
Verification is a service class for verifying the connection between DICOM devices. When verifying the connection, it is necessary to check Verification. For details on connection verification, see 7.3 Connection Check under MU: Maintenance Utility.

1.

Click the Print SCU setting tab.

5.

Click [OK].
The system returns to the [Setting the Server Equipment] window.

Click

MU050009.ai

2. 3.

Enter an AE name (e.g., FCR-CSL) in the AE Name field under Print SCU setting. Specify the Timeout value (timeout value between DICOM messages: 300).

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-23

IN-24
Set up DICOM (Settings for Storage SCU) (option)
The procedure for setting information for this equipment concerning DICOM Storage output is described below.

4. 5.

Specify the Timeout value (timeout value between DICOM messages: 300). Click [OK].
The system returns to the [Setting the Server Equipment] window.

1. 2.

Click [DICOM setting].


The Set up DICOM window opens.

Click the Settings for Storage SCU tab.

Click

MU050008.ai

3.

Enter an AE name (e.g., FCR-CSL) in the AE Name field under Settings for Storage SCU.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-24

IN-25
Disk drive settings
The procedure for setting the DVD drive that is to be connected to the server equipment (CR-IR 391CL machine).

3.

Click [View] to specify the drive path.


The Browse for Folder window opens.

1.

Click [Disk drive settings].


The Disk drive settings window opens.

IN000208.ai

4. 5.

Select the connected DVD RW drive (D:) and then click [OK].
The system returns to the Disk drive settings window.

Click the downward arrow mark ( ) for Disk format application type, and then select a disk format application type (Dedicated application).
Setting
Not specified OS Dedicated application : Default

Description
Does not provide formatting. Provides formatting with the dedicated application. Provides formatting with an OS function.

MU000507.ai

2.

Enter a management disk drive name (e.g., DVD) in the Drive name field under [Setting a Disk Drive for Server Management].

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-25

IN-26
6. 7.
Click [View] to specify the Dedicated application format path.
The Open window opens.

9.

Check what is selected for Drive to be created in Set up PDI and click [Edit].

Select C:\Program Files\FujiFilm\Hobbit\System\ FFUdfFmtToolForVista on the folder selection window.

MU060209.ai

Notepad starts.

MU060210.ai

10. Input a facility name.


IN000209.ai

C:\Program Files\FujiFilm\Hobbit\System\FFUdfFmtToolForVista is input automatically in the Dedicated format application path field.

11. From the File menu, select Overwrite.


The Save as... window opens.

8.

Input rD to the end of the path (r represents a space and D represents a DVD drive path).

12. Confirm the Encoding and click Save.


NOTE
Select ANSI or Unicode character code. Input data can be saved only when either ANSI or Unicode is selected.

REFERENCE
After the input as directed above, the description in the Dedicated format application path field will be as follows.

13. Select Close Notepad from the File menu.


Notepad window closes and the system returns to the Disk drive settings window.

14. Click [OK].


The system returns to the Setting the Server Equipment window.

15. Click [Next].


The Setting the Image Reader window opens.
020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-26

IN-27
4.4.6 Setting the Image Reader 4.4.7 Setting the Film Printer
See 5.6 Setting the Film Printer (option) under MU: Maintenance Utility.

4.4.8 Setting the Storage Device


See 5.7 Setting for DICOM Storage Device (option) under MU: Maintenance Utility.

4.4.9 Exiting the Simplified Setup Wizard

MU000509.ai

MU000522.ai

1. 2. 3. 4. 5.

Enter an Image Reader name (default: Image Reader) in the Equipment name field. Enter an Image Reader host name (default: RU0) in the Host name field. Enter an Image Reader IP address (default: 172.16.1.10) in the IP Address field. Remove the check mark from Check the box to use Patient information display. Click [Next].
The Simplified settings completed window opens.

1.

Click [Finish].
The system returns to the Service Utility top window.

The Simplified setup wizard is now closed.

IMPORTANT
For an output device set up using the Simplified setup wizard, be sure to use the User Utility to perform Setting a destination for image output.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-27

IN-28 4.5 RU Settings


To perform RU software settings, be sure to observe the procedures shown in the flow below.
4.5.1 Installing the RU PC-TOOL 4.5.2 Setting Up and Checking Firewall Settings 4.5.3 Installing and Registering RU-AP

4.5.1 Installing the RU PC-TOOL


The RU PC-TOOL is a utility (also referred to as the FCR TOOL) that exercises RU-AP installation, RU-Config setup, data backup, and other functions. For the operations of the CR-IR 391CL and RU, it is necessary that the RU PCTOOL be installed in the CR-IR 391CL system.

1. 2. 3. 3.

Select [Control Panel] from the


The Control Panel window opens.

menu.

Double-click User Accounts.


The User Accounts window opens.

Select Turn User Account Control on or off.


The User Accounts Control window opens.

Click

AWV22035_E.ai

The Turn User Account Control on or off window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-28

IN-29
4.
Remove the checkmark from Use User Account Control (UAC) to help protect your computer.

8. 9.

Insert the RU APL Software CD into the CR-IR 391CLs DVD drive. Select [Computer] from the DVD RW drive (D:).
The Set Up PC-TOOL window opens.

menu and double-click

10. Click [INSTALL].


MU060211.ai

The following window opens.

MU060212.ai

5.

Click [Restart Now].


The PC restarts. After a while, the CR-IR 391CL starts up.

6.

Within 2 to 3 seconds of the appearance of the initial window, sequentially click its upper left and upper right corners.
Click the upper left corner first, and then the upper right corner.
MC000307.ai

00000118.ai

The ServiceUtilityAuthentication window opens.

7.

Click [Cancel] to close the window.


The system returns to the desktop screen.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-29

IN-30
11. Select For FTP-Server, and click [SET].
NOTE
Be sure to select For FTP-Server. If For Client PC is selected, installation cannot be done successfully. If you have erroneously selected For Client PC and clicked [SET], perform installation again by following the procedure below. See Appendix 8 Corrective Procedure to be Performed after Improper RU PC-TOOL Installation under IN: Installation of the RU Service Manual.

13. Click [NEXT].

FRCH7043.ai

FRCH7168.ai

14. Click [Install].

The confirmation window opens.

MC000428.ai

12. Click [OK].

FRCH7045.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-30

IN-31
15. When the installation completes, click [Finish]. 16. Press the <Enter> key.
The following window opens.

FRCH7193.ai

FRCH7046.ai

17. Ptess the <Enter> key.


The Windows Security Alert window opens.

The following window opens.

18. Click [Unblock].

FRCH7192.ai

MC000149.ai

The system returns to the Set Up PC-TOOL window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-31

IN-32
19. Click [Exit].

MC000308.ai

20. Remove the RU APL Software CD from the DVD drive, and restart the
PC.
After a while, the CR-IR 391CL starts up.

21. Within 2 to 3 seconds of the appearance of the initial window,


sequentially click its upper left and upper right corners.
Click the upper left corner first, and then the upper right corner.

00000118.ai

The ServiceUtilityAuthentication window opens.

22. Click [Cancel] to close the window.


020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-32

IN-33
4.5.2 Setting Up and Checking Firewall Settings

5.

Check to see that BmpServer is checkmarked.

1. 2. 3.

Select [Control Panel] from the


The Control Panel window opens.

menu.

Double-click [Windows Firewall].


The Windows Firewall window opens.

Select Allow a program through Windows Firewall.

MU060213.ai

The Windows Firewall Settings window opens.

MC000305.ai

4.

Select the Exceptions tab and check to see that FTP (File Transfer Protocol) is checkmarked.

If BmpServer does not exist, perform the procedure described later in n If BmpServer does not exist (Adding a program).

MC000092.ai

If the FTP item does not exist, perform the procedure described later in n If FTP does not exist (Adding a program).
020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-33

IN-34
If FTP does not exist (Adding a program)

2.

Click [Browse...].
The Browse dialog opens.

1.

In the Exceptions tab of the Windows Firewall Settings window, click [Add program...].

MC000095.ai

3.
MC000093.ai

Enter C:\WINDOWS\SYSTEM32\FTP in the filename field, and click [Open]. Click [OK] in the Add a Program window.
The system returns to the Exceptions tab in the Windows Firewall window.

4. 5.

The Add a Program window opens.

Make sure that FTP is checkmarked.

NOTE
File Transfer Program or ftp may be displayed, instead of FTP.

MC000094.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-34

IN-35
If BmpServer does not exist (Adding a program)

2.

Click [Browse...].
The Browse dialog opens.

1.

In the Exceptions tab of the Windows Firewall Settings window, click [Add Program...].

MC000095.ai

3.
MC000093.ai

Select C:\Program Files\FujiFilm\FCR\TOOL\BmpServer, and click [Open]. Click [OK] in the Add a Program window.
The system returns to the Exceptions tab in the Windows Firewall window.

4. 5.

The Add a Program window opens.

Make sure that BmpServer is checkmarked.

MC000094.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-35

IN-36
Setting up the FTP port Setting up inetinfo

1.

In the Exceptions tab of the Windows Firewall Settings window, click [Add Port].
The Add a Port window opens.

1.

In the Exceptions tab of the Windows Firewall Settings window, click [Add Program...].

MC000313.ai

2. 3. 4.

In the Name: field, enter FTP_port. In the Port number field, enter 21.
MC000093.ai

Click TCP to select it.

The Add a Program window opens.

MC000097.ai

5.

Click [OK].
The system returns to the Exceptions tab in the Windows Firewall Settings window.

MC000094.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-36

IN-37
2.
Click [Browse...].
The Browse window opens.

4.

Click [Open].
The system returns to the Add a Program window.

MC000095.ai MC000311.ai

3.

Select C:\WINDOWS\system32\inetsrv\inetinfo, and click [Open].

5.

With inetinfo being selected, click [OK].


The system returns to the Windows Firewall window.

MC000310.ai

MC000312.ai

6. 7.
020-221-01E 04.28.2009 FM5535

Make sure that inetinfo is checkmarked, and click [OK].


The system returns to the Control Panel.

Close the Control Panel window.

CR-IR 391CL Service Manual

IN-37

IN-38
4.5.3 Installing and Registering RU-AP
Install the RU-AP in the CR-IR 391CL. To do this, use the RU PC-TOOL and perform the procedures set forth in this section.

3.

Click [Start].

NOTE
Before installing the RU-AP, turn ON the RU power.

REFERENCE
This section describes the procedures, by way of example, where settings are made as follows: INSTALL VERSION : 1.0 LANGUAGE : NONE BRAND TYPE : NONE

1.

Turn the RU OFF and then turn it ON.

NOTE
Although a connection error occurs on the RU side, it will pose no problem to subsequent work if you simply clear the alarm.
FRCH7048.ai

4.

Enter RU NAME and RU IP ADDR.

2.

Select Computer from the DVD RW drive (D:).

menu and double-click

NOTE
Enter the IP address of the RU that has been set on the CR-IR 391CL.

#1[Input] #2[Input]
FRCH7050.ai

5.

Click [PING].
[Click]

FRCH7051.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-38

IN-39
6.
Check the result of PING, and click
#2

to close the window.

8.

Click [OK].

#1 [Check]

FRCH7054.ai

9.
0% loss should appear.
FRCH7052.ai

Select INSTALL VERSION and click [OK].

[GOOD indication]. If the following message appears, the result is normal. | Ping statistics for 172.16.1.10: | Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), [NO GOOD indication].

| |

FRCH7055.ai

Other than above is all abnormal. (The selected IP address of the RU is displayed.)

10. Make sure that INCH is selected for IP Size Code Setting (size
system of the IP used).

NOTE
In the case of NO GOOD indication See MT: Machine Troubleshooting of the RU Service Manual.

7.

Click [INSTALL].
[Click]

FRCH7053.ai

REFERENCE
When clicking on [INSTALL], Under maintenance appears on the operation panel of the RU.

FRCH7114.ai

11. If configuration information other than the default settings is used at


the request of the institution, change the settings.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-39

IN-40
12. Click [SET]. 14. Confirm the installation precautions.
CAUTION
While the flash ROM is being written into, never turn OFF the RU or CR Console. If you turn OFF the power, the program stored in the memory becomes damaged and cannot restart.

15. Click [SET].


When you click on [SET], the installation screen opens on the CR Console display. While the flash ROM is being written into, the RUs LED blinks.
FRCH7060.ai

NOTE
Do not close the installation screen until the flash ROM write process is completed. If you inadvertently close the installation screen, return to Step 7 and perform the installation procedure again. The flash ROM write process takes about 8 minutes.

13. Check to see that 172.16.1.20 and CL0 have been set for IP
ADDRESS and CL NAME, respectively.

NOTE
If the FTP Server IP Address setting has been changed before the installation of the RU software, enter the new address.

[Click]

The installation screen appears on the CR-IR 391CL display.

FRCH7176.ai

While the flash ROM write process is being performed, the LED and Cassette ready lamp blinks.

FRCH7191.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-40

IN-41
16. Verify that the flash ROM write process is completed, and then press
the <Enter> key twice.
#1 [Check]

18. Check the version of the RU software, and close RU PC-TOOL.


#1 [Check] #2 RU TYPE CR-IRxxx: Model name of the RU to be connected is displayed. GOOD indication The text is displayed in black. NO GOOD indication The text is displayed in red or the version number is not displayed. RU NAME IP ADDRESS RU TYPE VERSION ru0 172.16.1.11 CR-IRxxx 1.1

#2 [Press 2 times] Enter key

FRCH7066.ai

17. Click [OK].


#3 [Click]

FRCH7068.ai

NOTE
FRCH7067.ai

If NO GOOD is indicated, go back to Step 1. and perform installation again.

19. Verify that the RUs LED is extinguished, and then turn OFF the RU.
REFERENCE
The message Under maintenance is displayed on the operation panel. However, turning OFF the RU power does not affect the RUs functionality.

20. Turn ON the power of the RU.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-41

IN-42
4.5.4 Setting the User Account Control (Activate)
Turn on the User Account Control.

5.

Click [Restart Now].


The PC restarts. After a while, the CR-IR 391CL starts up.

1. 2. 3. 4.

Select [Control Panel] from the


The Control Panel window opens.

menu.

6.

Within 2 to 3 seconds of the appearance of the initial window, sequentially click its upper left and upper right corners.
Click the upper left corner first, and then the upper right corner.

Double-click User Accounts.


The User Accounts window opens.

Select Turn User Account Control on or off.


The Turn User Account Control on or off window opens.

Place a checkmark in Use User Account Control (UAC) to help protect your computer.

00000118.ai

The ServiceUtilityAuthentication window opens.

7.

Click [Cancel] to close the window.


The system returns to the desktop screen.

MU060214.ai

The following window opens.

MU060212.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-42

IN-43 4.6 Film Printer Software Setup (option)


This section shows the procedures of making a DICOM Print setup in order that any of the following film printers will be able to receive images from the CR-IR 391CL.

4.6.1 Installing the Option Key for Application Key


If the Free Layout Print option key or DICOM Print option key is not installed, that is required.

NOTE
When the option key and/or the application key is to be installed, it is required that the CR-IR 391CL is connected to the network. Make sure that network connection has been established before performing the installation.

DRYPIX 1000/3000
See 8.1 Network Connection (DICOM) under IN: Installation of the DRYPIX 1000/3000 Service Manual.

DRYPIX 2000
See 9. CLIENT SETTINGS under IN: Installation of the DRYPIX 2000 Service Manual.

1. 2.

Insert an option key CD into the DVD drive. Select Computer from the DVD RW drive (D:).
The installation start window opens.

DRYPIX 4000
See 10. SETTING CLIENTS under IN: Installation of the DRYPIX 4000 Service Manual.

menu and double-click

DRYPIX 7000
See 10. SETTING CLIENTS under IN: Installation of the DRYPIX 7000 Service Manual.

DRYPIX PRIMA
See 7. SETTING OF THE EQUIPMENT under IN: Installation of the DRYPIX PRIMA Service Manual.
INAppE0001.ai

3.

Click [Continue].
A window opens to indicate the completion of installation.

INAppE0002.ai

4. 5.
020-221-01E 04.28.2009 FM5535

Click [OK].
The system returns to the desktop screen.

Remove the CD from the DVD drive.

CR-IR 391CL Service Manual

IN-43

IN-44
4.6.2 Reinstalling the AP Key
Once you have installed the option key, be sure to reinstall the AP key. Reinstall the AP key using the AP key CD. The installation procedure is as follows:

4.6.3 DICOM Print Setup


See 4.4.5 Server Equipment Settings

1. 2.

Insert the AP key CD into the DVD drive. Select Computer from the DVD RW drive (D:).
The installation start window opens.

menu and double-click

INAppE0004.ai

3.

Click [Continue].
A window opens to indicate the completion of installation.

INAppE0005.ai

4. 5.

Click [OK].
The system returns to the desktop screen.

Remove the CD from the DVD drive.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-44

IN-45 4.7 Checking Connections with Other Equipment


This section shows the procedures of checking the connections with other pieces of equipment such as those described below.

Starting up the RUs Maintenance Utility


Start up the RUs Maintenance Utility.
For the procedure to start up the RUs Maintenance Utility, see Maintenance Utility (MU) of the RU Service Manual.

Displaying the Connection check window

Running a connection check

Checking connection to the Host equipment

1.

Click the down-arrow button (

) in the field and select the connection

destination.

2.

IN000201.ai

Click [Verify connection].


The DOS prompt opens.

If the following message is displayed four times, the connection is in proper working order. Reply from 172.16.1.10: bytes=32 time<10ms TTL=128

1.

Click [Connection check] under Maintenance tool on the Service Utility top window.
The Connection Check window opens.

REFERENCE
Values for time<10ms and TTL=128 in the message above vary depending on the network status. Connection remains normal even though such values vary.

NOTE
If a message saying Request timed out. shows up, go back to 4.3 Setup by the Simplified Setup Wizard and check the settings. Furthermore, check the supply of power to individual network equipment (such as LAN wires and HUBs) and make certain that connections are in proper operating order in order that communication with connected equipment is performed successfully.

3.
IN000217.ai

Repeat Steps 1 and 2 for each of the connection destinations such as the RU and DICOM printer on which a connection check is necessary.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-45

IN-46
DICOM verification
Perform the following procedure when a DICOM printer or a DICOM storage device is connected. * This procedure is unable to perform to a DICOM Media Storage.

4.8 Exiting the Service Utility


1.
Click on the Service Utility top window.

1.

Click the down-arrow button (

) in the field and select the connection

The system returns to the desktop window.

destination.

2.

Click [Verify connection].


When a message saying DICOM Verification was succeeded. shows up on the FFServiceUtility window, the connection is in proper working order.

NOTE
If a message saying DICOM Verification was failed. shows up, go back to 4.3 Setup by the Simplified Setup Wizard and check the settings. In consultation with the Service Manual of the destination equipment, establish a condition where DICOM communication can be performed successfully.

3.

Click [OK].
The system returns to the Connection check window.

Terminating the connection check

1.

Click [Finish] on the Connection Check window.


The system returns to the Service Utility top window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-46

IN-47

5. Checkup Work
5.1 Checking the Startup and Configuration of the RU 5.2 Checking the System Configuration

5.1 Checking the Startup and Configuration of the RU


REFERENCE
If the RU must be used with its IP address changed, make an IP address setting on the RU in consultation with Appendix 5 Changing the IP Address of an RU under CR-IR 391RU Service Manual. For details, see Appendix 5 Changing the IP Address of an RU under CR-IR 391RU Service Manual.

5.3 Checking Every Step from the Inputting of Images to the Saving of Images onto DVD

5.1.1 Checking the Startup of the RU


5.4 Checking Output Images (option) Output images are checked for image format, nonuniformity, and on-film annotation format.

NOTE
Before making a startup check on the RU, be sure to log onto a CR-IR 391CL client. If the RU is started without logging onto any CR-IR 391CL client, an error message indicative of a connection trouble appears on the operator panel of the RU.

NOTE
To operate the CR-IR 391CL system program (including utility programs), Windows Explorer must be shut down. Operating the program with Windows Explorer up and running may cause a problem, such as system hang-up or media error, to occur. However, this does not apply when the procedure where to start up from Windows Explorer is determined.

Preparatory work (login)

1.

On the desktop, double-click

The CR-IR 391CL server application starts and its initial window opens. When the server application gets up and running, the icon representing the CR-IR 391CL server shows up in the task tray in the bottom-right corner of the window.

IN000402.a

Internet Explorer starts and the User Selection window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-47

IN-48
2.
On the User Selection window, click the top, bottom, left, and then right edge portions of the window in order.

3.

Enter the password fieldengineer (in lower-case single-byte characters only) and click .

IN000501.ai

The Password input window for service engineers shows up.

NOTES
The top, bottom, left, and right edge portion clicks should be done slowly. Too fast clicking may render the detection of position information impossible. In the event of a login failure, click [Finish] and close the User Selection window once. Click [FCRWeb] on the desktop to reopen the User Selection window and go over the above-mentioned operation again.

IN000502.ai

The Study List window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-48

IN-49
Checking the startup of the RU

1. 2.

Turn ON the power of the RU. Make sure that the RUs operator panel looks identical to the onL.

FRCH7150.ai

NOTE
If the onL fails to appear on the RUs operator panel and an error window shows up instead, perform fault analysis by consulting Troubleshooting. Troubleshooting of the RU Service Manual

REFERENCE
Prior to shipment from the factory, the IP addresses of the RU and CR-IR 391CL were set to their default values. The default values are as follows:
Reader Unit IP Address : 172.16.1.10 FTP Server IP Address : 172.16.1.20 RU

CR-IR 391CL IP Address : 172.16.1.20


FRCH7155.EPS

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-49

IN-50
5.1.2 Checking the RUs Version

2.

1.

From the

menu, select All Programs Accessories Run.

Check and compare the RUs version registered on the LIST OF EXISTING RUs and the version found on the RU-APL CD-ROM that came with the RU.
LIST OF EXISTING RU RU NAME IP ADDRESS RU TYPE ru0 172.16.1.10 CR-IR391 VERSION V1.0

In the Run window that opens, type C:\Program Files\FujiFilm\FCR\ TOOL\RuPcTool\RuPCTool.exe and click [OK].
#1 [Select]

[Check] Software version.

#2 [Select] RU-APL CD-ROM #3 [Select]

CR-IR 391RU APL Software V1.0

FRCH7157.ai

3.
#4 [Type in] #5 [Click]

If the version of the RU registered on the LIST OF EXISTING RUs is found to be lower than the version on the RU-APL CD-ROM in Step 2, perform a software version upgrade.

NOTES
In such cases below, upgrade the version of the software to install the latest version to the RU. The RU version registered to the LIST OF EXISTING RU is found to be lower than the version described on the RU-APL CD-ROM. For procedural details, see 3.2 Updating the RU Software under MC: Checks, Replacement and Adjustments of Parts.

4.
FRCH7154.ai

Close RU PC-TOOL.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-50

IN-51
5.1.3 Checking the RUs Message File
NOTE
If UPDATE (RU MESSAGE) is not grayed out, install the RU message file using the following steps: I. Click [UPDATE (RU MESSAGE)].
[Insert] RU-APL CD-ROM

1.

Set the RU-APL CD-ROM into the DVD drive.

[Click]
FRCH9518SM.ai

The Set Up PC-TOOL window opens.

2.

Check to see that the text UPDATE (RU MESSAGE) is grayed out.

FRCH9520SM.ai

REFERENCE
The grayed-out state of the text UPDATE (RU MESSAGE) indicates that the RUs message file has been correctly installed.

The UPDATE (RU MESSAGE) window opens. II. Click [OK]. The system returns to the Set Up PC-TOOL window. III. Make sure that UPDATE (RU MESSAGE) is grayed out.

[Check] UPDATE (RU MESSAGE) is in a grayed-out state.

[Check] UPDATE (RU MESSAGE) is in a grayed-out state.

FRCH9519SM.ai

FRCH9519M.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-51

IN-52
3.
Click [Exit] to close the Set Up PC-TOOL window.

5.1.4 Checking the RU Configuration

1.

[Click]

If use is to be made of the equipments configuration information in a state other than default settings at the request of the institution concerned, make setting changes in accordance with Appendix A: Setting up RU-Config.
For details, see Appendix 4: Setting the RU-Config in MC: Checks, Replacement and Adjustment of Parts.

FRCH9522SM.ai

4.

Remove the RU-APL CD-ROM from the DVD drive.

[Remove] RU-APL CD-ROM


FRCH9521SM.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-52

IN-53 5.2 Checking the System Configuration


Automatic output setting
This function generates automatic image printout or performs automatic image storage at study verification or exposure completion. Necessary settings are to be performed in the User Utility.
Appendix 4: Settings for Automatic Output in MU: Maintenance Utility.

5.3 Checking Every Step from the Inputting of Images to the Saving of Images onto DVD
This section describes the procedures to ensure that image data is saved on DVD successfully and random access to the saved image data is possible on the DVD.

Preparatory work (login)


Start up the RU and perform logging into the CR-IR 391CL client.

Automatic verification of a study


This function automatically verifies a study that has been subjected to exposure processing. Necessary settings are to be performed in the User Utility.
Appendix 5: Setup for Auto-verify in MU: Maintenance Utility.

NOTE
If the RU is up and running and is logged onto the CR-IR 391CL client, skip the procedures below and go to Preparatory work (Preoperation checks on the RU) Preparatory work (preoperation checks on the RU)

Automatic logoff setting


This function enables the client application to log off the system automatically if no manipulations are performed within a preset time. Necessary settings are to be performed in the User Utility.

1.

Turn ON the RUs power switch. If it is already ON, just leave it as it is and there is no need to do anything else. On the desktop, double-click .

2.

The CR-IR 391CL server application starts and its initial window opens. When the server application gets up and running, the icon representing the CR-IR 391CL server shows up in the task tray in the bottom-right corner of the window.

IN000402.ai

Internet Explorer starts and the User Selection window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-53

IN-54
3.
On the User Selection window, click the top, bottom, left, and then right edge portions of the window in order.

4.

Enter the password fieldengineer (in lower-case single-byte characters only) and click [Login].

IN000501.ai

IN000502.ai

The Password input window for service engineers shows up.

The Study List window opens.

NOTES
The top, bottom, left, and right edge portion clicks should be done slowly. Too fast clicking may render the detection of position information impossible. In the event of a login failure, click [Finish] and close the User Selection window once. Click [FCRWeb] on the desktop to reopen the User Selection window and go over the above-mentioned operation again.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-54

IN-55
Preparatory work (preoperation checks on the RU)
NOTES
For the IP used for image/conveyance checks, an IP of the maximum size used in the hospital should be employed. Make sure that the IP to be used does not contain any important image data exposed.

Preparatory work (disk setup)


Make preparations for disk writing, as follows.

1. 2.

Affix the label on the case of the disk used for storing images and enter the date and the title Image storage disk. Click which is found in the indicator field located in the upper-

1. 2.

Check to ensure that the onL screen appears. Perform Erasure on the spontaneous radiation and image accumulated on the IP to be used.
For details of Secondary Erasure processing, see the RU Operation Manual.

right corner of the window.

IN000512.ai

The indicator field (Disk) shows up.

3.

Perform IP exposures.

NOTE
Expose the IP at X-ray tube voltage of 80 kVp. Otherwise, the image check cannot be done normally.

INSTRUCTIONS
Expose two IPs of the largest size to be used at the users site to the following dose. With the X-ray tube, the first IP should be exposed in a normal orientation, and the second in a 180-degree upside-down orientation.
: Tungsten X-ray tube X-ray tube X-ray exposure dose : 1 mR : IP of 14"14" (3535 cm) or 14"17" (3543 cm) size Maximum size Reference conditions : Distance 1.8 m Voltage 80 kVp Amperage 50 mA Time 0.013 sec

IN000503.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-55

IN-56
3.
Click [Utility].
The Disk Operation window opens.

5.

Insert a disk, onto which to write, into the tray and click [Next].
A window opens asking if you wish to format the inserted disk.

IN000603.ai

The window above opens only when an unformatted disk was inserted.

6.

Click [OK].
The fotmat window opens.

N000522.ai

4.

Click [Replacing Disks].


The Replacing Disks window opens.

MU000043.ai

IN000504.ai

7.

Click [Start].
The following window opens.

MU000044.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-56

IN-57
8.
Click [OK].
The following window opens.

12. Leave the default number as it is and click


NOTE

If some data has been entered and the default lost consequently, click .
MU000045.ai

The system returns to the Disk Operation window.

9.

Click [OK].
The system returns to the format window.

13. Click [Update].


The equipment information gets updated.

10. Click [Close].


The Specify how to handle the disk window opens.

IN000505.ai

11. Select For Image Storage and click [Next].


The Specify disk name window opens.

IN000523.ai

14. Click [Close].


The system returns to the Indicator window.

IN000506.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-57

IN-58
15. Click
located in the lower left corner of the Indicator window.

Conducting Image input check inspection


For details of the inspection procedure to be carried out, see the CR-IR 391CL Operation Manual.

The display of the Indicator window gets updated.

16. Verify the following check items.


Check items: Device : Ensure that the device name that has been set by means of the Service Utility is in place. : Ensure that the device name and available write area (%), both of Status which were entered in/under Step 8, are being indicated. : Ensure that For Storage Disk is being displayed. Usage Disk Write : Ensure that Write enabled is being displayed.

IMPORTANT
Automatic storage on DVD by means of verification operation is an important and essential function, make certain that storage takes place without fail.

1.

Click

located at the bottom of the study list window.

17. Click [OK].

IN000527.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-58

IN-59
The Patient ID window opens.

3.

Enter the following items of patient information and click [Next].


Patient Name : Fuji Tarou Date of Birth : 1972.AUG.15 : Male Sex The exposure menu registration window opens.

IN000508.ai

2.

Enter the patient ID (0123456789) and click [Next].


The detailed patient information input window opens.
IN000510.ai

IN000509.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-59

IN-60
4.
Click to open the second page.
Click

5.

Click [QC/TEST] and click [IMAGE-FORMAT].


#1 Click #2 Click

IN000608.ai IN000606.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-60

IN-61
6.
Click [Start Study].
The Start Study window opens.

8.

After the input of the image, click [Image Viewer].

IN000227.ai

Click
IN000226.ai

7.

Insert the IP cassette that has been readied in the course of Preparatory work (Preoperation checks on the RU) under 5.3 Checking Every Step from the Inputting of Images to the Saving of Images onto DVD into the RU.

The Image Viewer window opens.

Cassette Ready lamp [illuminating]

FRCH101006.ai

Shortly after the initiation of reading of the IP, images that have been read into the CR-IR 391CLS monitor show up.
020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-61

IN-62
9.
After the image has shown up, click [Verify].

11. After selecting the study, click


box.

located in the

Click
IN000610.ai IN000632.ai

The following window opens.

10. Click

in the upper left corner of the window.

The system returns to the Study List window.

IN000633.ai

12. Click[Output].
The system returns to the Study List window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-62

IN-63
13. Click
under .

15. After selecting the study, click


box.

located in the

IN000611.ai

The Requesting for disk insert window opens. The Image retrieve window opens.

IN000613.ai

IN000612.ai

IN000614.ai

14. Click [OK].


A listing of studies on the disk shows up.

When the image reading completes, the Image Viewer window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-63

IN-64
16. After viewing the on-screen image, click
of the window. in the upper left corner

17. Click and hold on the horizontal scrollbar and drag it rightward to
scroll.

Click
Since image reading occurs from the disc, the [Save/Verify] button becomes hidden from view.

IN000616.ai

N000615.ai

* Check to make sure that the study item that has been output is shown on the study list and the other items being displayed such as the patient ID are correct.

The system returns to the Study List window.

18. Ensure that the image that has been read in is not falling under the
heading DB managing.

Check here.

IN000617.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-64

IN-65
19. Click
located in the indicator field.

5.4 Checking Output Images (option)


When the DICOM print option is installed, perform the following operations: Film annotation character format Format check Irregularity, sensitivity and density checks

Click

IN000618.ai

The Indicator window opens.

20. Make sure that neither error nor warning is logged in the event tab.

IN000619.ai

21. Click [OK].


The Indicator window closes.

22. Remove the cassette from the RU.


020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-65

IN-66
Checking the film annotation character format Checking the format (option)
When the DICOM print option is installed, perform the following operations:

1.

Check to see that the film annotation character format information entered from the CR-IR 391CL is properly printed out onto film. Also, check for blurred, chipped, or otherwise abnormal character printings.

1.

Checking the image format


As measured from the outermost outline of film that has been output, make certain that the width of the blank margin should measure 2 mm or smaller in actual dimension on the IP.

REFERENCE
The example in the figure below represents a printout that would be generated when the default film annotation character format is used (image size : 2636cm (10"14"), print format : Single). When the default settings are used, character strings (1) through (17) are printed out.
(1) Hospital name (Institution name)
FUJIFILM HOSPITAL

PERFORMING A CHECK
Ensure that the blank margin is 2 mm or less in width. If an irregularity is found, See MT: Machine Troubleshooting of the RU Service Manual.
2mm or less Image frame

0400167 6

A0000A020

(12) IP No. (2) EDR mode + Menu code (3) System ID + Image No.

Blank margin

FRCH7102.EPS

(13) Image processing conditions


SKULL, GENERAL

(4) Patient ID (5) Patient name

NOTE
(10) Film mark (7) Sex (8) Age or Date of birth
R->L

G 1.0G#0.7+0.50R5Q0.5 L 4.0S200C 1.2 1.0AP

0000000001

MARY ADAMS [F] 23 SCALE 50% RT-04 1992 11 27 [17:43]

(9) Pair processing information (11) Reduction ratio

Depending on the IP reading size and film size, distances measured on film differ from their counterparts actually measured on the relevant IP. Therefore, calculate actual dimensions on the IP on the basis of distances measured on the film and the reduction ratio of the film using the following equation: Actual dimension on the IP = Measured value 100 Reduction ratio (%)

(14) Exposure menu name (17) Exposure time (16) Image inversion mark (6) Date of exposure (15) Standardization conditions + Correction item

IN000532.EPS

If any abnormality is found, see 6.4 Film Annotation Characters under MU: Maintenance Utility.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-66

IN-67
Checking for nonuniformity, sensitivity and density

1.

3.

Check that the output film and the image displayed on the CR-IR 391CL monitor are both free from peculiar irregularities.
If any abnormality is found, see MT: Machine Troubleshooting of the RU Service Manual.

Verify that there is no unusual nonuniformity found on the output film or on the image displayed on the image monitor.

PERFORMING A CHECK
There should be no uneven density difference in the main scan direction.
If there is any uneven density difference, compare the films output from the two IPs of the same size, and determine whether such nonuniformity is caused by the machine or X-ray tube.

2.

Check the system sensitivity (S value) indicated on the film that was output.
For details of the procedure to check the S value, see Checking the S Value in IN: Installation of the RU Service Manual.

If there is uneven density difference in the same direction on two films

REFERENCE
To check the S value on the monitor, take a look at the location shown below.

IP (first) in normal orientation IP (second) in vertically inverted orientation


FRCH7100.EPS

Check this S value.

The machine may be the cause of such nonuniformity. See MT: Machine Troubleshooting of the RU Service Manual.

If positions of uneven density difference are different

IN000609.ai

IP (first) in normal orientation

IP (second) in vertically inverted orientation


FRCH7101.EPS

The X-ray tube may be the cause of such nonuniformity.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-67

IN-68

6. Setup File Backup and RU Error Log Verification/Deletion


This section explains about the procedures for backing up the CR-IR 391CL and RU setup files and verifying/deleting the RU error log. When making backups, have the following items on hand. One DOS/V-formatted FD or USB Memory Stick (for RU) One DVD disk (for CR-IR 391CL)

NOTE
Never turn OFF the CR-IR 391CL or RU power during a backup process. If the power turns OFF, the machine may fail to startup.

6.1 Backing Up the CR-IR 391CL Setup File 6.2 Backing Up the RU Setup File 6.3 Verifying and Deleting the RU Error Log 6.4 Turning OFF the CR-IR 391CL and RU

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-68

IN-69 6.1 Backing Up the CR-IR 391CL Setup File


Back up patient information, setting information and log information.

2. 3. 4. 5.

Click [Eject].
The tray of the DVD drive opens.

Preparatory work
Make sure that the writing of all image data to the image storage disk has been completed. Onto the case of the backup-purpose disk, affix its supplied label and clearly mark thereon the date of backup along with the description For Backup Purposes.

Remove the disk. With the label side facing up, put the DVD back into its case labeled Image storage disk. Close the now-empty tray. Click [Update].
Only [Device Name] is shown while [Status], [Usage] and [Disk Write] become hidden from view.

Disk removal
This section describes the procedure to remove the image storage disk.

1.

Click

located in the upper-right corner of the Study List window.

icon_IN0602.ai

The Indicator window (Disk) opens.

MUApp0002.ai

IN000620.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-69

IN-70
6.
Click [OK].
The system returns to the [Study List] window.

7.

Click [Close] in the upper-left corner of the Study List window.

REFERENCE
For V1.1(B) or later, click at the bottom of the Main Window.

IN000633.ai

The [20339] Application will be terminated. dialog shows up.

IN00062 .ai

IN000625.ai

8. 9.

Click [OK].
The Select Server Application Behavior window opens.

Select Exit and click [OK].

IN000634.ai

The system returns to the desktop.


020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-70

IN-71
Staring up the Backup Utility

1.

4.

Right-click the icon representing the CR-IR 391CL server in the task tray at the bottom right of the desktop window.

Type in the username medicalservice and the password fieldengineer from the keyboard.

NOTES
Both username and password are lower-case single-byte characters only, without including space.

IN000402.ai

A right-click menu opens.

The username medicalservice must be typed in from the keyboard because it is not pre-registered on the pull-down menu.

2.

Click [Backup Utility].


The following confirmation window opens.

MU000035.ai

5.
MU000034.ai

Click [OK].
The following Main Menu window opens.

3.

Click [OK].
Upon system termination, the following User authentication window opens.

IN000635.ai MU000036.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-71

IN-72
6.
Click [Backup].
The Backup window opens.

10. After making the following checks, click

to continue.

I.

IN000627.ai

I.

Make certain that Drive D is current. Ensure that the folder name is the date (in YYYYMMDDhhmmss format) on which the backup was performed.

IN000626.ai

The window to confirm the deletion of log information opens.

7.

Checkmark all the following items (


).

Patient information Setting information Log information Delete logs after completing backup processing.

8. 9.

Click [Start].
The Select folder. window opens.

Open the tray of the DVD drive and insert the backup-purpose disk.

MUApp0003.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-72

IN-73
11. Click [OK].
The window to confirm the execution of disk formatting opens.

14. Click [OK].


The following window opens.

MU000045.ai

15. Click [OK].


The system returns to the format window.
MUApp0004.ai

16. Click [Close].


Upon completion of the backup processing, the following completion window opens.

12. Click [OK].


The fotmat window opens.

MU000042.ai

17. Click [OK].


The system returns to the Main Menu window.
MU000043.ai

13. Click [Start].


The following window opens.

18. Click [Finish].


The system returns to the Select Server Application Behavior window.

MU000044.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-73

IN-74
Verification work to be performed after completion of a backup operation

3.

In the Select Server Application Behavior window, select Start up Client Application and click [OK].

1.

Select Computer from the

menu and double-click DVD drive

(D:). And then check to make certain that the files shown on the following screen shot are stored.

IN000636.ai

The login window opens.

4.

Log in using the password fieldengineer.


The Study List window opens. For the procedure to log in, see 5.3 Checking Every Step from the Inputting of Images to the Saving of Images onto DVD.

5. 6.
IN000629.ai

Click

on

Check to see that the list stored on the disk is displayed.

2.

Remove the backup disk from the DVD drive and insert the image storage disk.

N000630.ai

7.

Click

located in the indicator field.

The system returns to the Indicator window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-74

IN-75
8.
Make certain that Event has no error information recorded on it.
The [20339] Application will be terminated. dialog shows up.

IN000625.ai

11. Click [OK].


The Select Server Application Behavior window opens.

12. Select Exit and click [OK].

IN000631.ai

9.

Click [OK].
The system returns to the Study List window.
IN000634.ai

10. Click [Close] in the upper-left corner of the Study List window.
REFERENCE
For V1.1(B) or later, click at the bottom of the Main Window.

The [29151] Server application will shut down. dialog shows up.

IN000637.ai

IN000633.ai

13. Click [OK].


The system returns to the desktop.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-75

IN-76 6.2 Backing Up the RU Setup File


This section explains about the procedure for making an FD (or USB Memory Stick) backup by saving the RU machine-specific data onto an FD (or USB Memory Stick) after the completion of setup.

3.

From [LIST OF EXISTING RU], select a target RU for backup.


[Select]

1. 2.

Insert an FD (or USB Memory Stick) into the CR-IR 391CLs FDD (or USB connectors) . From the menu, select All Programs Accessories Run. In the Run window that opens, type C:\Program Files\FujiFilm\FCR\ TOOL\RuPcTool\RuPCTool.exe and click [OK].
#1 [Select]

RU NAME IP ADDRESS RU TYPE ru0 172.16.1.10 CR-IRxxx

VERSION V1.0

RU TYPE CR-IRxxx: Model name of the RU to be connected is displayed.

FRCH316A01.EPS

4.
#2 [Select]

Click [FTP].
[Click]

#3 [Select]

FRCH316A02.ai

For details about FTP, see the RU Service Manual.

5.
#4 [Type in] #5 [Click]

From the BACKUP pull-down menu, select the items you want to back up.
CONFIGURATION LOG ALL SCN ALL DATA
ERROR LOG CONFIGURATION TRACE LOG HISTORY LOG LOG ALL SCN ALL DATA SCN LIGHT COLLECTING DATA SCN OPTICAL DATA
FRCH316A04.ai

[Select]

FRCH7154.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-76

IN-77
6.
Click [EXECUTE].
[Click]

8.

Make sure that the selected location is being displayed, click [OK].
#1 [Confirm] The selected location is displayed.

FRCH316A03.ai

7.

Select a backup destination folder.

#2 [Click]

NOTE
If and when you back up data to an FD, load a formatted FD into the CR-IR 391CL. This is because it is impossible to select the FD drive (a:\) unless an FD is being loaded in the drive.
#1 [Click]
FRCH316A10.ai

9.

Check the backup destination location again, and click [OK].


#1 [Confirm] #2 [Click]

FRCH316A06.ai

10. When the backup completion window opens, click [OK].


NOTE
#2 [Select]

If the data has been backed up to an FD, make sure to click [OK] before taking out the FD.
[Click]
FRCH316A09.ai

FRCH316A05.ai

11. Click the

button on the upper-right corner of the window.

The system returns to the desktop

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-77

IN-78 6.3 Verifying and Deleting the RU Error Log


6.3.1 Verifying the RU Error Log
By illustrating a case of viewing the latest error log, the procedure is described below.

3.

Click [UPDATE].

1.

Select an RU under LIST OF EXISTING RUs in the main menu of the RU PC-TOOL.
RU NAME IP ADDRESS RU TYPE ru0 172.16.1.10 CR-IRxxx VERSION V1.0 The latest error log is added to the end of the list. RU TYPE CR-IRxxx: Model name of the RU to be connected is displayed.

FRCH4414.EPS

2.

Click [ERROR DB].

FRCH4434.ai

FRCH4433.ai

The ERROR DB window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-78

IN-79
6.3.2 Deleting the RU Error Log

1. 2.

Start up the RU PC-TOOL, and in the ERROR DB window that opens, click the [CLEAR] button. Exit the RU PC-TOOL.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-79

IN-80 6.4 Turning OFF the CR-IR 391CL and RU


Turning OFF the CR-IR 391CL form the Study List Window Turning OFF the CR-IR 391CL form the Task Tray

1.

Right-click the CR-IR 391CL server icon on the task tray in the bottomright corner of the desktop window.

1.

Click [Close] in the upper-left corner of the Study List window.


The [20339] Application will be terminated. dialog shows up.
IN000402.ai

Its right-click menu opens.

IN000625 ai

IN000638 ai

2. 3.

Click [OK].
The Select Server Application Behavior window opens.

2.

Select Shutdown the PC.


The [29151] Server application will shut down. dialog shows up.

Select Shutdown the PC and click [OK].


The [29151] Server application will shut down. dialog shows up.

IN000637.ai

3.
IN000637 ai

Click [OK]. Turn OFF the RU power.

4. 5.

Click [OK]. Turn OFF the RU power.

4.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-80

IN-81

7. Links to Individual Option Items


Shown below are the appendixes to see when additionally installing options and/or making setting changes:

Setting for saving images into DICOM storage equipment


See Appendix 1: Settings for Saving Images into DICOM Storage Equipment in Appx IN: Installation Appendix.

Settings for Connection of the NAS


See Appendix 2: Settings for Connection of the NAS in Appx IN: Installation Appendix.

Setting a DICOM MWM Patient information


See Appendix 3: Setting a DICOM MWM Patient information in Appx IN: Installation Appendix.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

IN-81

IN-82
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

IN-82

Appx IN I

CR-IR 391CL Service Manual

Appx IN: Installation Appendix

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN I

Appx IN: Installation Appendix

Appx IN II
Reason
New release (FM5535) Revision for software V1.1(B) (FM5563)

Control Sheet
Issue date
04/28/2008 01/08/2010

Revision number
01 02

Pages affected
All pages Appx IN 1-2, 3, 7, 9, 2-1 to 36, 3-1 to 8

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN II

Appx IN III
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx IN III

Appx IN IV
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx IN IV

Appx IN 1-1

Appendix 1 Settings for Saving Images into DICOM Storage Equipment


This appendix describes the setup procedure for saving images into DICOM storage equipment.

1. Hardware Setup
Connect the CR-IR 391CL and the DICOM storage equipment through TCP/IP networking as illustrated below.
100BASE-TX cable TCP/IP

Before setup
Make sure the setup of the DICOM storage equipment has been completed. Make sure the setup of the CR-IR 391CL main unit has been completed. A DICOM storage output key is required.

CR-IR 391CL

DICOM storage equipment


INAppQ0001.EPS

Overall workflow
1. Hardware Setup

NOTES
Do not connect a telephone line to the network connector on the CR-IR 391CL system. Cables used for connection to the CR-IR 391CL system should be of the type compliant with the IEC950/UL1950 standards.

2. Software Setup 2.1 Installing the Option Key 2.2 Reinstalling the AP Key 2.3 Settings in the Service Utility 2.3.1 Settings Regarding This Equipment (DICOM storage SCU settings) 2.4 Changing the Display Gradation Correction LUT File

3. Connection Check

4. Backing Up the Setup File

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 1-1

Appx IN 1-2

2. Software Setup
2.1 Installing the Option Key

2.1 Installing the Option Key


The Saving to DICOM storage device option key is required.

NOTE
When the option key and/or the application key is to be installed, it is required that the CR-IR 391CL is connected to the network. Make sure that network connection has been established before performing the installation.

2.2 Reinstalling the AP Key

2.3 Settings in the Service Utility 2.3.1 Settings Regarding This Equipment (DICOM storage SCU settings)

1. 2.

Insert an option key CD into the DVD drive. Double-click DVD drive (D:).
The installation start window opens.

2.4 Changing the Display Gradation Correction LUT File

INAppE0002.ai

3.

Click [Continue].
A window opens to indicate the completion of installation

INAppE0003.ai

4. 5.
020-221-01E 04.28.2009 FM5535

Click [OK].
The system returns to the desktop screen.

Remove the CD from the DVD drive.

CR-IR 391CL Service Manual

Appx IN 1-2

Appx IN 1-3 2.2 Reinstalling the AP Key


Once you have installed the option key, be sure to reinstall the AP key. Reinstall the AP key using the AP key CD. The installation procedure is as follows:

2.3 Settings in the Service Utility


2.3.1 Settings Regarding This Equipment (DICOM storage SCU settings)
This section shows the procedures of making DICOM equipment settings. This section describes how to make settings on this equipment regarding the DVD drive, the DICOM Print option, and DICOM storage.

1. 2.

Insert the AP key CD into the DVD drive. Double-click DVD drive (D:).
The installation start window opens.

Items that can be set in the DICOM settings window


Name
Media Storage Setting AE name (I.) Name for identification purposes Input method: typed-in text when the DICOM protocol is used. Maximum character count: It should be MEDIA. 16 characters Maximum pixel density size of images that are stored in the disk drive for management. Whether images should be in a compressed form or not when stored on the disk drive for management. Input method: Single selection ST HQ Input method: Single selection Compress. Do not compress.

Description

Setting value

Maximum pixel density size for a stored image (II.)


INAppE0004.ai

3.

Click [Continue].
A window opens to indicate the completion of installation.

Whether or not to specify data compression for stored images (III.) Setting multi-byte character (IV.) Print SCU setting AE name (V.)

Whether or not to store additional Input method: Single selection (attendant) information in multibyte On: Store. characters, if any, on the media. Off: Do not store. Name for identification purposes Input method: typed-in text when the DICOM protocol is used. Maximum character count: It should be FCR-CSL. 16 characters Timeout value at the command level. Input method: typed-in text Acceptable characters: single-byte numeric characters Value range: 1 to 3600

Timeout value (VI.)


INAppE0005.ai

4. 5.

Click [OK].
The system returns to the desktop screen.

Presentation Context (VII.)

Setting of abstract syntaxes being Input method: multiple selection used. BasicGrayscalePrint: Not selectable and fixed to Yes. Verification: Yes/No Name for identification purposes Input method: typed-in text when the DICOM protocol is used. Maximum character count: It should be FCR-CSL. 16 characters Timeout value at the command level. Input method: typed-in text Acceptable characters: single-byte numeric characters Value range: 1 to 3600

Remove the CD from the DVD drive.

Setting for Storage SCU AE name (VIII.)

Timeout value (IX.)

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 1-3

Appx IN 1-4
Setting procedure

5.

Select the [Settings for Storage SCU] tab.

1. 2. 3. 4.

Start up the Service Utility.


The Service Utility top window opens.

Click [Connected equipment].


The Setting connection devices window opens.

Click [Server (this equipment)].


The Server equipment settings window opens.

Click [DICOM setting].


The DICOM setting window opens.
Click

INAppxQ0002.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx IN 1-4

Appx IN 1-5
6.
Make the following settings.

VIII. IX.

INAppxQ0003.ai

VIII. Enter the AE name FCR-CSL. IX. Enter the value 300 for the timeout between DICOM messages by typing from the keyboard or by clicking the or .

7. 8. 9.

Click [OK].
The system returns to the Server equipment settings window.

Click [OK].
The system returns to the Setting connection devices window.

Click [Back].
The system returns to the Service Utility top window.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx IN 1-5

Appx IN 1-6 2.4 Changing the Display Gradation Correction LUT File
Described herein is the procedure used to change LUT files so that the display gradation correction processing is performed when transmitting images to DICOM storage devices.

3.

Click the View tab.


A window like that shown below opens.

NOTE
When transmitting FCR images to storage devices, the CR-IR 391CL system uses a gradation correction LUT file named DICOMStorageLUT.env. To change the DICOMStorageLUT.env file to a different gradation correction LUT file, do so following the procedure explained below.

Preparatory work (folder option change)


In the CR-IR 391CL system, the folder where LUT files are located is set up in hidden folders. Because such hidden folders are not displayed with the default settings, it is necessary to have all those folders be displayed properly before starting the relevant work. After completing the necessary work, the folder where an LUT file is located must be set up again in a hidden folder.

INAppU0001.ai

4.

NOTE
Prior to starting the necessary preparatory work, ensure that the CR-IR 391CL server application has been exited. If such work is performed while the CR-IR 391CL server application is running, the CR-IR 391CL operation will go unstable.

Select [ Show hidden files and folders] from Files and Folders in the Advanced settings: field.
The selected item will be highlighted.

1. 2.

Select Control Panel from the


The Control Panel window opens.

menu.

Double-click [Folder Options].


The Folder Options window opens.
INAppU0002 .ai

5. 6.

Click [OK].
The system returns to the Control Panel window.

Click

at the upper right corner of the window to close it.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx IN 1-6

Appx IN 1-7
Changing the LUT file
In the CR-IR 391CL system, DicomStorageLUT.env is stored as the DICOM Storage output LUT file (10bit) in the folder shown below. Replace this file for the gradation conversion LUT file that has been readied appropriately.

Changing the folder option


Restore as follows the folder options settings changed during the preparatory work.

1. 2. 3.

Select Control Panel from the


The Control Panel window opens.

menu.

1. 2.

Rename the readied gradation conversion LUT file to DicomStorageLUT.env. Replace the LUT file renamed at step above for DicomStorageLUT. env that is located in the folder shown below.
Location for copying : C:\ProgramData\FujiFilm\Hobbit\Lut Filename : DicomStorageLUT.env

Double-click [Folder Options].


The Folder Options window opens.

Click the View tab.


A window like that shown below opens.

INAppU0003.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx IN 1-7

Appx IN 1-8
4.
Select [ Do not show hidden files and folders] from Files and Folders in the Advanced settings: field.

INAppU0004.ai

5. 6.

Click [OK].
The system returns to the Control Panel window.

Click

at the upper right corner of the window to close it.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx IN 1-8

Appx IN 1-9

3. Connection Check
Preparatory work
This section describes the procedures to perform setup as to whether or not Automatic Output is enabled and also make setting of an output timing value.
For more information on how to make settings, see Appendix 4: Settings for Automatic Output in MU: Maintenance Utility.

Outputting images to storage devices

1.

In the patient information input window, specify patient data and an exposure menu.
For details of patient data input operation, see the CR-IR 391CL Operation Manual.

2.

On the Study List window, select a registered study and then click [Start Study].
The Start Study window opens.

REFERENCE
To perform display gradation correction processing for an image to be transmitted to a storage device, the relevant LUT file needs to be changed accordingly. For detailed procedure, see 2.4 Changing the Display Gradation Correction LUT File in Appx IN: Installation Appendix.

Starting up the CR-IR 391CL

1.

On the desktop screen, double-click the

icon.

The CR-IR 391CL opening window appears. In about one minute, the CR-IR 391CL login window opens.

2.

Log in the system.


The Study List window opens. For information on how to log in to the CR-IR 391CL, see Preparatory work (login) in 5.3 Checking Every Step from the Inputting of Images to the Saving of Images onto DVD of IN: Installation.
IN000227.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 1-9

Appx IN 1-10
3.
Making sure that the cassette loading lamp on the RU panel is illuminating, load a cassette into the cassette set unit of the RU.

4.

Click

in the bottom-right corner of the CR-IR 391CL window.

The Study List window opens.

5.
Cassette Ready lamp [illuminating]

Perform the following operation:


In the case of automatic output
I. Click in the upper-right corner of the window.

The Indicator window opens. II. Click the [Output status] tab. The output status is displayed.
FRCH101006.ai

In a while after the reading from the IP has started, the image read into the CR-IR 391CL monitor is displayed.

III. Check to see that there is no queue left. IV. Check to see that the image is now stored on the DICOM storage equipment.

In the case of manual output

I.

II.

INAppxQ0004.ai

IN000226.ai

I. In the study display area, select a study you want to output. II. Click [DICOM Transmission]. The Settings for DICOM Transmission window opens.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx IN 1-10

Appx IN 1-11
III. Make the following settings: VII. After the image transfer, check to see that there is no queue left. VIII. Check to see that the image is now stored on the DICOM storage equipment.

NOTE
Make sure after data transfer that the image stored on the DICOM storage equipment is displayed appropriately.

INAppxQ0005.ai

Item
Priority HIGH : High priority MEDIUM : Medium priority LOW : Low priority

Description

IV. Click [Output]. V. Click in the upper-right corner of the window.

The Indicator window opens. VI. Click the [Output status] tab. The output status is displayed.
<During transfer> <After transfer>

INAppxQ0006.ai

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx IN 1-11

Appx IN 1-12

4. Backing up the Setup File


Back up the CR-IR 391CL setup file.
For details of the backup procedure, see 6.1 Backing Up the CR-IR 391CL Setup File under IN: Installation.

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

Appx IN 1-12

Appx IN 2-1

Appendix 2 Settings for Connection of the NAS


Described herein is the setup procedures required for connection with NAS.

Turning ON/OFF the NAS


See 5. Turning ON/OFF the NAS

Mirroring Setting for Image Folder


See 6. Mirroring Setting for Image Folder

NOTE
Actual procedures may differ because the NAS is procured by the FUJIFILM representative according to the specified specification. In that case, qury the FUJIFILM representative about the procedures.

Restoring Procedures Using the Automatic Backup File


See 7. Restoring Procedures Using the Automatic Backup File

Before setup
Make sure the setup of the CR-IR 391CL main unit has been completed.

Overall workflow
Connecting the CR-IR 391CL and the NAS with each other via the hub, using a network cable.
1. Hardware Setup

Make network setting and service utilities setting for NAS. Check up that the NAS is correctly connected to the computer. Backing up the setup file

2. Software Setup

3. Connection Check

4. Backing up the Setup File

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-1

Appx IN 2-2

1. Hardware Setup
1.1 Specifications
1.1.1 LAN
Item
Standard Connector Communication protocol IP address setting File sharing Supported OS Number of concurrently connected users Number of concurrently connected PCs 1000BASE-T : IEEE802.3ab 100BASE-T : IEEE802.3u RJ-45 TCP/IP Can be set manually (There are types which can only be used with DHCP.) Windows file sharing Windows XP / Windows Vista / Windows Server 2003 5 or more 5 or more

1.1.3 Operation-Certified Models and Software

LinkStation
LS-W1.0TGL/R1 : manufactured by Buffalo, capacity: 1.0TB, RAID1 compatibility LS-W2.0TGL/R1 : manufactured by Buffalo, capacity: 2.0TB, RAID1 compatibility

Contents

TeraStation
TS-WX1.0TL/R1 : manufactured by Buffalo, capacity: 1.0TB, RAID1 compatibility TS-WX2.0TL/R1 : manufactured by Buffalo, capacity: 2.0TB, RAID1 compatibility

AutoSync
Auto Sync V3.60

NOTE
Auto Sync is used for mirroring the Image folder. (Described later) This software can be got from following web site. http://www.memeo.com/autosync.php

1.1.2 RAID
Item
Level

Contents
RAID1 (mirroring)

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-2

Appx IN 2-3 1.2 Installing hardware


1.2.1 TeraStation

1. 2. 3.

Connect the power plug of the TeraStation to UPS. Connect the TeraStation and hub with the LAN cable. Turn on the power supply switch on the front of the TeraStation.

NOTE
It is recommended that the electric power is supplied to NAS through UPS.

1.2.2 LinkStation

1. 2. 3.

Connect the power plug of the LinkStation to UPS. Connect the LinkStation and hub with the LAN cable. Turn on the power supply switch on the front of the LinkStation.

NOTE
It is recommended that the electric power is supplied to NAS through UPS.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-3

Appx IN 2-4

2. Software Setup
2.1 Installation procedures for TeraStation (TS-WX1.0TL/R1 and TS-WX2.0TL/R1) 2.1.1 Network Setting 2.1.2 TeraStation RAID Setting 2.1.3 Shared Folder Setting 2.1.4 Confirming Connection between TeraStation and CR-IR 391CL

2.1 Installation procedures for TeraStation (TS-WX1.0TL/R1 and TS-WX2.0TL/R1)


2.1.1 Network Setting

Installing NAS Navigator2


NOTE
Install NAS Navigator2 after turning off the UAC. For details, see Setting the User Account Control in 1.3.1 Installing and Setting Windows Vista under MC: Checks, Replacement and Adjustment of Parts See the screens. For details, refer to the user manual that comes with the NAS you purchased. Do not install unnecessary software other than NAS Navigator2.

2.2 Installation Procedures for LinkStation (LS-WH1.0TGL/R1 and LS-WH2.0TGL/R1) 2.2.1 Network Setting 2.2.2 LinkStation RAID Setting 2.2.3 Shared Folder Setting 2.2.4 Confirming Connection between LinkStation and CR-IR 391CL

2.3 Setting in the Service Utility

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-4

Appx IN 2-5
1.
Insert a CD that comes with the TeraStation, and double-click D drive.

2.

Click [NAS NAvigator2 Install].


The following window opens.

NOTE
When it does not start automatically, open the drive and execute TSNavi.exe.

INApp19051.ai

3.

Click [install].
The following window opens.

INApp19048.ai

The main window opens.

INApp19052.ai

4.

Click [Next].
The Congratulations! window opens.

INApp19049.ai

INApp19053.ai

5.

Click [Finish]
Terminate TSNavi.exe.

NOTE
Turn the UAC back ON after completing the installation for NAS Navigator2.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-5

Appx IN 2-6
Temporarily match the network segment between TeraStation and CR-IR 391CL
NOTE
In case of the NAS icon is not displayed after double-clicking the NAS Navigator2 icon, temporarily matching of network segment of TeraStation and CR-IR 391CL is needed. In that case, perform this section and Restoring the network setting of the CR-IR 391CL.

3.

Right-click Local Area Connection and select Properties, select Internet Protocol Version 4 (TCP/IPv4), and click [Properties].

INApp19104.ai

1.

Check the IP address of the current TeraStation.


I. Start up NAS Navigator2 by clicking the BUFFALO NAS Navigator icon on the desktop. II. Make a note of IP Address and Subnet Mask of the NAS, that are displayed on the screen.
INApp19107.ai

4.

Change the IP address and subnet mask of the PC so that NAS and CR-IR 391CL are in the same network segment.
[Ex.]
Before changing
CR-IR 391CL IP address Subnet mask IP address Subnet mask 172.16.1.20 255.255.255.0 169.254.163.179 255.255.0.0

After changing
169.254.160.210 255.255.0.0 169.254.163.179 255.255.0.0

INApp19105.ai

III. Terminate NAS Navigator2.

NAS

2.

Click Control Panel Network and Sharing Center Manage network connections to open the Network Connection window.

5. 6. 7. 8.

Click [OK] to close the Properties window. Close the Local Area Connection Properties window. Close the Network Connection window. Close the Network and Sharing Center window.

INApp19106.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-6

Appx IN 2-7
Setting the IP address of the TeraStation

4.

Enter the following value, and click [OK].


Item
I. II. III. Obtain IP address automatically via DHCP Renew IP address IP Address remove the checkmark remove the checkmark (Ex.) 172.16.1.80 (match this to the network segment of the CR-IR 391CL) (Ex.) 255.255.0.0 (match this to the network segment of the CR-IR 391CL) 0.0.0.0 (Enter 0 to all)

1.

Double-click the icon on the desktop screen to start up the NASNAvigator2.

Setting

IV. Subnet Mask

2.

Right-click the icon of the TeraStation, and select Properties.

V.

Default Gateway

I. II. III. IV. V.

INApp19098.ai

The Properties window opens.

3.

Select the IP Settings tab in the Properties window.


The following window opens.
INApp19111.ai

The Confirm Password window opens.

5.

Enter the following password, and click [OK].


Password : password

INApp19112.ai INApp19110.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-7

Appx IN 2-8
6.
If the following window opens, close it by clicking the the right top of the window. button on

Restoring the network setting of the CR-IR 391CL


NOTE
In case of Temporarily match the network segment between TeraStation and CR-IR 391CL has been done, perform this section.

1.

Turn back the value of the IP address and the subnet mask to the value before changing them in Temporarily match the network segment between TeraStation and CR-IR 391CL.

INApp19113.ai

7.

When the following dialog opens, click [No] to close it.

INApp19114.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-8

Appx IN 2-9
2.1.2 TeraStation RAID Setting

3.

Select System Storage RAID Array from the menus on the upper side of the window.

Changing the RAID setting of the TeraStation to the normal mode


Temporarily delete the RAID mode that is already set.

1.

Right-click the TeraStation icon, and select Open Web Admin.

INApp19062.ai

2.

Enter the following user name and password to log in to the Web setting window.
Username : admin Password : password

INApp19054.ai

4.

Select Array 1.
The [RAID Array (Array 1)] setting window opens.

INApp19060.ai

INApp19066.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-9

Appx IN 2-10
5.
Click [Delete RAID Array] .
The Warning dialog opens.

8.

After completion of the changing process, click [Refresh] to go backreturn to the main screen.

INApp19068.ai

6.

Click [Apply].
The RAID Array operation window opens.

INApp19069.ai

7.

Enter the same number as the displayed one in the window, and click [Apply].
The changing process of the RAID Array starts.

INApp19067.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-10

Appx IN 2-11
Changing the RAID setting of the TeraStation to RAID1

3.

1.

SelectSystem Storage RAID Array from the menus on the upper side of the window.

Right-click the TeraStation icon, and select Open Web Admin.

INApp19062.ai

2.

Enter the following user name and password to log in to the Web setting window.
Username : admin Password : password
INApp19115.ai

4.

Select Array 1.
The [RAID Array (Array 1)] setting window opens.

INApp19060.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-11

Appx IN 2-12
5.
Make the following settings, and click [Create Raid Array].
I. RAID Mode : Select raid1 II. Place checkmarks to Disk1 and Disk2 (Or, select HDDs that are to be used for RAID1. Ex: Disk3 and Disk4)
I. II.

7.

Enter the same number as the displayed one in the window, and click [Apply].

NOTE
While configuring RAID for several hours (approx. 6hours for 1TB), file transfer speed to NAS decreases. While configuring RAID, the INFO/ERROR lamp on the front side of the LinkStation/TeraStation flashes orange. If you turn OFF NAS while it is configuring, the configuring process is interrupted. When the power is turned on again, configuring will resume from where it was interrupted. (Ex.) When you turn OFF the 1TB LinkStation after configuring RAID for 3hours

INApp19072.ai

The Warning dialog opens.

RAID configuring resumes the next time the power is turned on and it will take 3 more hours to process.
The changing process of the RAID Array starts.

INApp19073.ai

6.

Click [Apply].
The [RAID Array operation] window opens.
INApp19067.ai

8.

After completion of the changing process, click the [Refresh] button to return to the main screen.

INApp19074.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-12

Appx IN 2-13
2.1.3 Shared Folder Setting

4.

Make the following settings, and click [Save].


I. Name : FujiFilm II. Volume : Array 1 III. Recycle Bin : Disable

1.

Right-click the TeraStation icon, and select Open Web Admin.

INApp19062.ai

I.

2.

Enter the following user name and password to log in to the Web setting window.
Username : admin Password : password

II. III.

INApp19078.ai

The system returns to the main screen.


INApp19060.ai

3.

Select Shared Folders Folder Setup from the menus on the upper side of the window.
The New Folder setting window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-13

Appx IN 2-14
2.1.4 Confirming Connection between TeraStation and CR-IR 391CL

1. 2.

Select Network from the Start menu.


The Network window opens.

Confirm that the shared folder of the TeraStation (FujiFilm) is included in the configuration.

INApp19081.ai

3.

Confirm that the FujiFilm folder can be opened.

INApp19080.ai

After finishing setup of the TeraStation, continue setup procedure referring 2.3 Setting in the Service Utility.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-14

Appx IN 2-15 2.2 Installation Procedures for LinkStation (LS-WH1.0TGL/R1 and LS-WH2.0TGL/R1)
2.2.1 Network Setting

Temporarily match the network segment between LinkStation and CR-IR 391CL
NOTE
When the CR-IR 391CL and NAS are not in the same network segment, the following Web setting cannot be started up. Therefore, temporarily change the network segment of CR-IR 391CL to the segment of LinkStation.

Installing NAS Navigator2

1.

Install NAS Navigator2 referring the manual attached to the LinkStation.

1.

Check the current IP address of the LinkStation.


I. Start up NAS Navigator2 by clicking the BUFFALO NAS Navigator icon on the desktop. II. Make a note of IP Address and Subnet Mask of the NAS, that are displayed on the screen. III. Terminate NAS Navigator2.

NOTE
Install NAS Navigator2 after turning off the UAC. For details, see Setting the User Account Control in 1.3.1 Installing and Setting Windows Vista under MC: Checks, Replacement and Adjustment of Parts See the screens. For details, refer to the user manual that comes with the NAS you purchased. Do not install unnecessary software other than NAS Navigator2. After Installation finished, following icon will be created on the desktop.

2.

Click Control Panel Network and Sharing Center Manage network connections to open the Network Connection window.

NOTE
Turn the UAC back ON after completing the installation for NAS Navigator2.

INApp19095.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-15

Appx IN 2-16
3. 4. 5.
Right-click Local Area Connection and select Properties. Select Internet Protocol Version 4 (TCP/IPv4), and click [Properties]. Change the IP address and subnet mask of the PC so that NAS and CR-IR 391CL are in the same network segment.
[Ex.]
Before changing
CR-IR 391CL IP address Subnet mask IP address Subnet mask 172.16.1.20 255.255.255.0 169.254.163.179 255.255.0.0

Setting the IP address of the LinkStation

1.

Double-click the icon on the desktop screen to start up the NAS Navigator2.

After changing
169.254.160.210 255.255.0.0 169.254.163.179 255.255.0.0

2.

Right-click the LinkStation icon, and select Open Web setting.

NAS

INApp19116.ai

3.

Enter the following user name and password to log in to the Web setting window.
Username : admin Password : password

INApp19095.ai

6. 7. 8. 9.

Click [OK] to close the Properties window. Close the Local Area Connection Properties window.
INApp19099.ai

Close the Network Connection window. Close the Network and Sharing Center window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-16

Appx IN 2-17
4.
Select Network IP Address Properties from the menus on the left side of the window

Restoring the network setting of the CR-IR 391CL

1. 2. 3.

Turn back the value of the IP address and the subnet mask to the value before changing them in Temporarily match the network segment between LinkStation and CR-IR 391CL. Start up the NAS Navigator2 and confirm the IP Address of LinkStation is correctly changed. Confirm the network connection from PC to NAS using ping comand from command prompt.

INApp19100.ai

5.

Make the following settings, and click [Apply].


Item
Automatic via DHCP IP Address Subnet Mask Default Gateway Address Primary DNS Server Address Secondary DNS Server Address Disable 172.16.1.80 255.255.0.0 None None None

Setting

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-17

Appx IN 2-18
2.2.2 LinkStation RAID Setting

Changing the RAID setting of the LinkStation to RAID1

Changing the RAID setting of the LinkStation to the normal mode


Temporarily delete the RAID mode that is already set.

1. 2. 3. 4.

Log in to the Web setting window. Select Disk Management RAID Setup from the menus on the left side of the window. Select RAID Array 1.
The RAID setting window opens.

1. 2.

Right-click the LinkStation icon, and select Open Web setting. Enter the following user name and password to log in to the Web setting window.
Username : admin Password : password

Make the following settings, and click [Create Raid Array].


Item
RAID Mode Disk Structure RAID 1 Select disks to use for RAID1 (Disk1 and Disk2 or Disk3 and Disk4).

Setting

3.

Select Disk Management RAID Setup from the menus on the left side of the window.

The changing process of the RAID Array starts.

NOTE
While configuring RAID for several hours (approx. 6hours for 1TB), file transfer speed to NAS decreases. While configuring RAID, the INFO/ERROR lamp on the front side of the LinkStation/TeraStation flashes orange. If you turn OFF NAS while it is configuring, the configuring process is interrupted. When the power is turned on again, configuring will resume from where it was interrupted. (Ex.) When you turn OFF the 1TB LinkStation after configuring RAID for 3hours
INApp19101.ai

RAID configuring resumes the next time the power is turned on and it will take 3 more hours to process.

4. 5. 6.

Select RAID Array 1.


The RAID setting window opens.

5.

After the completion message appeared, operate following the guidance.

Delete all of the RAID Array settings. Close the RAID setting window.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-18

Appx IN 2-19
2.2.3 Shared Folder Setting

4.

Make the following settings, and click [Apply].


Item
Shared Folder Name Volume Recycle Bin FujiFilm Array 1 Disable

1. 2.

Log in to the Web setting window. Select Shared Folders Shared Folder Setup from the menus on the left side of the window.

Setting

INApp19102.ai

3.

Click [Add].

INApp19103.ai

The system returns to the main screen.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-19

Appx IN 2-20
2.2.4 Confirming Connection between LinkStation and CR-IR 391CL

1. 2. 3.

Select Network from the Start menu. Confirm that the shared folder of the LinkStation (FujiFilm) is included in the configuration. Confirm that the FujiFilm folder can be opened.

After finishing setup of the LinkStation, continue setup procedure referring 2.3 Setting in the Service Utility.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-20

Appx IN 2-21 2.3 Setting in the Service Utility


1. 2. 3. 4.
Start the Service Utility.
The Service Utility top window opens.

5.

Make the following settings, and click [OK].


I. II. III. IV. Equipment name : Optional Network path : Click [Browse], and select the FujiFilm folder in the NAS. Network drive : Optional After setting for [Network drive], click [Configuration].

Click [Connected equipment].


The Setting connection devices window opens.

Capacity of the specified drive is displayed in the [Maximum capacity] text box and at the right side of the text box. V. Maximum capacity : Optional (Specify capacity of NAS to be used by the CR-IR 391CL.)

Click [HDD].
The Image save settings window opens.
I. II. III. IV. V.

Place a checkmark to Save the image to your hard disk, and click [Add].

INApp19004E.ai

6.
INApp19001E.ai

Terminate the Service Utility.

The NAS setting window opens.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-21

Appx IN 2-22

3. Connection Check
3.1 Confirming Connection between LinkStation and CR-IR 391CL (Access to the Network Drive)
1. 2.
Select Computer from the Start menu.
The Computer window opens

3.2 Confirming Connection between TeraStation and CR-IR 391CL


1. 2.
Start up the CR-IR 391CL Server Application, and display the Indicator. Click the NAS icon.

INApp19044.ai

The Disk window in the Indicator opens.

Confirm that the FujiFilm folder can be opened.

3.

Confirm that the status of NAS and Disk Write are displayed.

INApp19045.ai

INApp19043.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-22

Appx IN 2-23
REFERENCE
NAS and DVD can be switched from Device Name.

INApp19117.ai

Enable images stores in HDD is added to System in the Service Utility. This setting is synchronized with the [Connected Equipment] [HDD] [Save the image to your hard disk] checkbox. When a checkmark is placed, the setup value becomes Yes, and when not, the setting value becomes No.

INApp19118.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-23

Appx IN 2-24

4. Backing up the Setup File


Back up the CR-IR 391CL setup file.
For details of the backup procedure, see 6.1 Backing Up the CR-IR 391CL Setup File under IN: Installation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-24

Appx IN 2-25

5. Turning ON/OFF the NAS


In the normal operation, NAS has to be turned ON before starting up the Server PC. Turn ON/OFF the NAS with either one of the 2 kinds of procedures. However, backup of the log/setting file may fail because of the operational mistakes in the manual turning. Therefore, making it always ON is recommended.

5.2 Manual ON/OFF


In case of TeraStation
Startup

NOTE
When Auto is selected on the backside switch, power of the NAS is turned ON/OFF synchronizing with the Server PC. However, the CR-IR 391CL might not recognize the NAS because it takes time to start up the NAS. Therefore, do not set the backside switch to Auto.

1. 2. 3. 1. 2.

Set the backside switch to Manual. Turn on the power supply switch on the front of the TeraStation. Start up the Server PC.

Stop

5.1 Always ON
In case of TeraStation

Shut down the Server PC. Confirm that the Server PC completely stops, and then turn the backside switch of the LinkStation to OFF.

1. 2.

Set the backside switch to Manual. Always make the TeraStation ON regardless of ON/OFF of the Server PC.

In case of LinkStation
Startup

In case of LinkStation

1. 2. 1. 2.

Set the backside switch to ON. Start up the Server PC.

1.

Always set the backside switch to ON regardless of ON/OFF of the Server PC.

Stop
Shut down the Server PC. Confirm that the Server PC completely stops, and then turn the backside switch of the LinkStation to OFF.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-25

Appx IN 2-26

6. Mirroring Setting for Image Folder


6.1 Creating a Save Destination Folder
Add a shared folder in the TeraStation. Create a shared folder in the TeraStation with the same procedure as 2.1.3 Shared Folder Setting. Shared folder name: Image_Mirror
For details, see 2.1.3 Shared Folder Setting.

6.2 Synchronization Function Setting


Installing Memeo AutoSync

1.

Execute

The Security Warning dialog appears.

2.

Click [Run].

NOTE
Install AutoSync after turning off the UAC. For details, see Setting the User Account Control in 1.3.1 Installing and Setting Windows Vista under MC: Checks, Replacement and Adjustment of Parts

INApp19082.ai

The Setup Wizard starts up.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-26

Appx IN 2-27
3.
Click [Next].

5.

Click [Finish].

INApp19083.ai

INApp19085.ai

The License agreement window opens.

The Memeo AutoSync shortcut is created on the desktop.

4.

Click [I Agree].

NOTE
Turn the UAC back ON after completing the installation for AutoSync.

INApp19084.ai

The installation starts.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-27

Appx IN 2-28
Synchronization function setting

4.

Specify the following folder for Folder A.


c:\FujiFilm\Hobbit\Data\Image

1. 2.

Double-click

on the desktop.

Click Memeo AutoSync Create Sync Plan.

INApp19088.ai

5.
INApp19086.ai

Specify the shared folder, Image_Mirror created in 6.1 Creating a Save Destination Folder for Folder B.

3.

Click [Next].

INApp19089.ai

INApp19087.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-28

Appx IN 2-29
6.
Click [Next].
The confirmation window opens.

8.

Enter an arbitrary name for Enter Sync Plan Name and click [Next].
(Ex.) Image Mirroring

INApp19090.ai

INApp19091.ai

7.

Click [Next].
A window to enter a name for Sync Plan opens.

9.

Remove the checkmark form Yes, send my configuration information, and click [Done].

INApp19092.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-29

Appx IN 2-30
10. Click the
to close the window.

6.3 Mirroring between NAS


In dual TeraStation configuration, data of the first TeraStation can be backed up in the 2nd TeraStation. Create a shared folder in the 2nd NAS, and the FujiFilm folder and Image_Mirror folder in the 1st TeraStation can be mirrored with the same procedures in 6.2 Synchronization Function Setting.

INApp19093.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-30

Appx IN 2-31

7. Restoring Procedures Using the Automatic Backup File


When NAS is connected, setting and log files are automatically saved in the NAS at the time of terminating the CR-IR 391CL. Here, procedures are described to restore the CR-IR 391CL using the automatically saved setup files and image files backed up by mirroring.

Deleting the Sync Plan

1.

Double-click

on the desktop.

The Memeo AutoSync window opens.

2.

Select Sync Plan (ex. : Image Mirroring) and click [Remove Sync Plan].

CAUTION
Before connecting the NAS to CR-IR 391CL, be sure to delete the Sync Plan of AutoSync. With the mirroring function of the SyncPlan, Image folders on the NAS side and the PC side are synchronized. Due to this function, proper image files on the NAS side might be overwritten by the collapsed image files on the PC side. Meanwhile, after restoring the Image folder on the PC side, be sure to turn on the mirroring function again.
INApp19119.ai

The Remove Sync Plan Confirmation window opens.

INApp19120.ai

3. 4.

Click [Yes].
The system returns to the Memeo AutoSync window.

Check no Sync Plan is displayed on Memeo AutoSync window.

INApp19121.ai

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-31

Appx IN 2-32
Connecting the NAS
NOTE
(*) Enter the following folder for DB path. \\(NAS Host name)\FujiFilm\Backup\(the latest day folder)\Database The latest day folder can be confirmed in NAS Host name : NAS navigator. Files are backed up on each day in the latest day folder : Backup folder in the NAS.Specify the last backup file that is backed up properly.

1. 2.

Connect TeraStation to the CR-IR 391CL. Restore the study files.


I. II. III. Open the Image_Mirror folder in the NAS. Copy all the files in the Image_Mirror folder. Paste them in the following image save folder of the CR-IR 391CL Server PC (*). c:\FujiFilm\Hobbit\Data\Image

3.

Restore the Image DB.


I. II. Start up the command prompt. Enter osql -Usa -Pfcr-dms -Slocalhost, and press the <Enter> key.

The osql utilities starts up.


IV.
INApp19046.ai

INApp19047.ai

Execute the following command to restore the Patient DB. Enter RESTORE DATABASE Patient FROM DISK = DB path(*)\Patient. bak WITH REPLACE. The following procedures are same as step III. Execute the following command to restore the Explanation DB. Enter RESTORE DATABASE Explanation FROM DISK = DB path(*)\ Explanation.bak WITH REPLACE. The following procedures are same as step III. Execute the following command to restore the Operation log DB. Enter RESTORE DATABASE History FROM DISK = DB path(*)\History. bak WITH REPLACE. The following procedures are same as step III. Enter RESTORE DATABASE ListConfig FROM DISK = DB path(*)\ ListConfig.bak WITH REPLACE. The following procedures are same as step III. Enter RESTORE DATABASE Preset FROM DISK = DB path(*)\Preset. bak WITH REPLACE. The following procedures are same as step III.

V. VI.

III.

Execute the following command to restore the Image DB.

a) Enter RESTORE DATABASE Study FROM DISK = DB path(*)\Study.bak WITH REPLACE. b) Press the [Enter] key. c) Enter go. d) Press the [Enter] key.

VII. Execute the following command to restore the Study List Config DB.

VIII. Execute the following command to restore the Preset DB.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-32

Appx IN 2-33
4.
Restoring System Config.
Copy the all the files for Backup folder of System Config(*1) in TeraStation to the folder of System Config(*2) CR-IR 391CL Server PC.

Reconfiguration of Synchronization function setting


For information, refer to Synchronization function setting under 6.2 Synchronization Function Setting

NOTE
(*1) Specify the following for Backup folder of System Config. \\(NAS Host name)\FujiFilm\Backup\(the latest day folder)\Config The latest day folder can be confirmed in NAS Host name : NAS navigator. Files are backed up on each day in the latest day folder : Backup folder in the NAS. Specify the last backup file that is backed up properly. (*2) Specify the following depending on the OS. c:\ProgramData\FujiFilm\Hobbit\Config

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-33

Appx IN 2-34
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-34

Appx IN 2-35
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-35

Appx IN 2-36
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 2-36

Appx IN 3-1

Appendix 3 Setting a DICOM MWM Patient information


Procedure to set a MWM device as a search target for patient information is described.

1. Hardware Setup
Connect the CR-IR 391CL and the DICOM storage equipment through TCP/IP networking as illustrated below.
100BASE-TX cable TCP/IP

Before setup
Setting has been made on the DICOM MWM equipment. Make sure the setup of the CR-IR 391CL main unit has been completed. DICOM ID MWM Key Software Option key is required. *1 The SCU AE Title of CR-IR 391CL set on the MWM server is FCR-SCU.
*1

CR-IR 391CL

DICOM MWM equipment


INApp21001.ai

Overall workflow
1. Hardware Setup

NOTES
Do not connect a telephone line to the network connector on the CR-IR 391CL system. Cables used for connection to the CR-IR 391CL system should be of the type compliant with the IEC950/UL1950 standards.

2. Software Setup 2.1 Installing the Option Key 2.2 Reinstalling the AP Key 2.3 Settings in the Service Utility

3. Connection Check

4. Backing Up the Setup File

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 3-1

Appx IN 3-2

2. Software Setup
2.1 Installing the Option Key

2.1 Installing the Option Key


The Saving to DICOM storage device option key is required.

NOTE
When the option key and/or the application key is to be installed, it is required that the CR-IR 391CL is connected to the network. Make sure that network connection has been established before performing the installation.

2.2 Reinstalling the AP Key

2.3 Settings in the Service Utility

1. 2.

Insert an option key CD into the DVD drive. Double-click DVD drive (D:).
The installation start window opens.

INApp21002.AI

3.

Click [Continue].
A window opens to indicate the completion of installation

INApp21003.AI

4. 5.
020-221-02E 01.08.2010 FM5563

Click [OK].
The system returns to the desktop screen.

Remove the CD from the DVD drive.

CR-IR 391CL Service Manual

Appx IN 3-2

Appx IN 3-3 2.2 Reinstalling the AP Key


Once you have installed the option key, be sure to reinstall the AP key. Reinstall the AP key using the AP key CD The installation procedure is as follows:

2.3 Settings in the Service Utility


1.
Start up the Service Utility.
For how to start up the Service Utility, see 2. Starting, Logging-in to, and Exiting the Service Utility under MU: Maintenance Utility.

1. 2.

Insert the AP key CD into the DVD drive. Double-click DVD drive (D:).
The installation start window opens.

The Service Utility top window opens.

2. 3.

Click [Linkage function].


The Setting the linkage function window opens.

Click [Linkage of MWM Patient information].


The Linkage of MWM Patient information window opens.

INAppE0004.ai

3.

Click [Continue].
A window opens to indicate the completion of installation.

INAppE0005.ai

4. 5.

Click [OK].
The system returns to the desktop screen.

Remove the CD from the DVD drive.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 3-3

Appx IN 3-4
4.
Specify the following settings.

5. 6. 7.

Click [OK].
The system returns to the Setting the linkage function window.

I. II.

Click [Back].
The system returns to the Service Utility top window.

Click [EXIT].

III. IV. V. VI. VII.

INApp21004.AI

No.
I. II. III. IV. V. VI. VII.

Item
Support the linkage of MWM Patient information Patient information to be searched first. Device name Host name DICOM AE name IP address Port number

Content
Place a checkmark to Support Select MWM Set the name of the equipment to be connected Set the name of the equipment to be connected on the network Set the DICOM AE name Set the IP address of the equipment to be connected Set the port number of the equipment to be connected

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 3-4

Appx IN 3-5

3. Connection Check
1.
Enter ID in the Input ID window of the patient-originated window, and press the <Enter> key.

REFERENCE
If you cannot connect to the MWM equipment, check that the following log file is created. Folder: C:\Users\ProgramData\FujiFilm\Hobbit\Log File name: DICOMMWMPI.log This file is always created at the time of establishing the session.

INApp21007.AI

INApp21005.AI

Patient information with the entered ID is retrieved from the DICOM MWM equipment and displayed.

To display the ProgramData folder, put a checkmark to Show hidden files and folders under the View tab in the Folder Options window.

INApp21006.AI

INApp21008.AI

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 3-5

Appx IN 3-6

4. Backing up the Setup File


Back up the CR-IR 391CL setup file.
For details of the backup procedure, see 6.1 Backing Up the CR-IR 391CL Setup File under IN: Installation.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 3-6

Appx IN 3-7
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 3-7

Appx IN 3-8
BLANK PAGE

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

Appx IN 3-8

PC-I

CR-IR 391CL Service Manual

PC: Performance Check

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

PC-I

PC: Performance Check

PC-II
Reason
New release (FM5535) Revision for software V1.1(B) (FM5563) All pages 1 to 7

Control Sheet
Issue date
04/28/2009 01/08/2010

Revision number
01 02

Pages affected

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

PC-II

PC-1

CR-IR 391CL Performance Checklist


The purpose of this checklist is to document the steps performed and settings determined during installation of the CR-IR 391CL system in accordance with the instructions of the CR-IR 391CL Service Manual. This checklist is not intended to replace the installation workflow described in the service manual but to be followed concurrently. Check system connections and output images not only during installation but also after servicing to ensure correct operation of the system prior to its delivery to the customer.

2. Software Setup
4. Software Setup under IN: Installation
Setting/checking the system date and time Installing the option key software DICOM print DICOM CR Storage MFP processing Free Layout DICOM MWM patient information Startup verification Pass Fail Pass Fail Pass Fail Pass Fail

Installation information
Equipment S/N : Site Name : Site Number : Room Name : Software Ver. : Installed by : Signature : Date of Installation/Servicing :

CR-IR 391CL setup for connection with other equipment IP address Subnet mask Host name Gateway address Registered AE title Media Storage Pass Fail Print SCU Storage SCU Pass Fail ( ( ( ) ) ) Default Change Default Change ( ( ) ) (172.16.1.20) (255.255.0.0)

Checklist
1. Hardware Setup
3. CR-IR 391CL Hardware Setup under IN: Installation
Checking the component items Equipment main unit Accessories Monitor

Pass Fail

Installing accessories/optional items

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

PC-1

PC-2
3. Checkout Procedures
5. Checkup Work under IN: Installation
Checking the connection between the CR-IR 391CL and the RU Checking the connection with another device (Manufacture : NAS  IP address: RAID setting in the NAS Image folder synchronization function Past images transfer function Device name : ) Pass Fail Checking required when the optional function is provided Registering a study from a client PC and performing such study Importing and displaying the general-purpose image data Pass Fail NA Pass Fail NA

Generating output of image data transferred from the Image Reader to a Pass Fail storage device NA Receiving Patient information via DICOM MWM ID Connection to the NAS Pass Fail N.A. Pass Fail N.A.

Checking the system settings Automatic output setting DVD Printer Generates automatic output. (after verification of a study)  Does not generate automatic output. Generates automatic output. (after verification of a study)   enerates automatic output. (after completion of an exposure) G Does not generate automatic output.  Generates automatic output. (after verification of a study)   enerates automatic output. (after completion of an exposure) G Does not generate automatic output.  Generates automatic output. (after verification of a study)  Does not generate automatic output.

N.A. (Not Applicable):  Shows that the relevant item is not targeted for this checkup.

4. Setup File Backup and RU Error Log Verification and Deletion


6. Setup File Backup and RU Error Log Verification/Deletion under IN: Installation

General-purpose file Storage

Setup file backup 5. Overall Test

Pass Fail Pass Fail

Automatic verification settings After confirmation of a study (after completion of an exposure) After passing (  Operation check Displaying image data transferred from the Image Reader on the monitor Pass Fail Automatically recording image data transferred from the Image Reader onto a DVD Reading image data from a DVD onto the hard disk to display it on the monitor Create a PDI from the study data Generating film output of an image displayed on the monitor Pass Fail Pass Fail Pass Fail Pass Fail NA ) minutes of specified time upon completion of confirmation No value is to be set up.

6. Storing Processed Films or Image Data at Institutions as the Records of the Performance Check Pass Fail

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

PC-2

PC-3

CR-IR 391CL Config List


6. Service Settings under MU: Maintenance Utility

4.

Setting is Also Possible with the User Utility


Check No.
4-1

Name
Whether to use guidance function on the exposure screen. Whether to perform automatic output of the studies re-verified (previously-verified studies which were verified once again after necessary modifications have been applied). Display unit of size measurement Display unit of weight measurement

Setup Value

1.

Localize Setting
Check No.
1-1 1-2 1-3 Date display format Time display format Enable images stored in HDD

4-2

Name

Setup Value

4-3 4-4

5.

Setting for Image Collection


Check No.
5-1 5-2 5-3 5-4 5-5 5-6 System ID (A-Z) Set number: Minimum value Set number: Maximum value Whether Pantomography processing is executed or not. Whether GS conversion for six Ts/1824 images is performed or not.

2.

Setting for Institution


Check No.
2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 Institution name em-size Institution name en-size Institution information 1 (Use paper print.) Institution information 2 (Use paper print.) Institution information 3 (Use paper print.) Institution information 4 (Use paper print.) Institution logo mark (Use paper print.) System name for which search conditions are displayed on the study list

Name
IP size selection (inch/metric)

Setup Value

Name

Setup Value

6.

Setting for Image Browsing


Check No.
6-1 6-2 6-3

Name
Display unit of measurement result Number of rows displaying additional image information Number of lines displaying additional image information

Setup Value

3.

Setting for Entering Patient Name


Check No.
3-1 3-2 3-3 3-4

Name
Whether an input column for kanji patient name is displayed or not. Character string length of patient ID (up to 64 characters) Padding method of patient ID Default patient ID value to be given when the actual patient ID is unavailable in the data received via DICOM communication from the ultrasound device.

Setup Value

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

PC-3

PC-4 7. Setting for General-purpose File Output


Check No.
7-1 7-2 7-3 7-4 7-5 7-6 7-7

Check

No.
8-10

Name
Shared folder monitoring interval [sec] on linkage with the receipt computer <Linkage= other than SANYO> Port number for receiving cable messages from the receipt computer <Linkage=FUJITSU> Receipt time-out value [msec] of continuous cable messages from the receipt computer <Linkage=FUJITSU>

Setup Value

Name
Path name at general-purpose file output destination at the time of automatic output. General-purpose file format at the time of automatic output. General-purpose file reduction rate % at the time of automatic output. General-purpose file image quality at the time of automatic output (compressibility) <effective when JPEG is selected> Name generation rule for general-purpose file at the time of output. Name generation rule for general-purpose file at the time of output (For studies other than CR). Default character strings to be output to patient information text file.

Setup Value

8-11

8-12

9.

Setting for Image Link


Check No.
9-1 9-2 9-3

Name
Whether support is provided or not to Image Link as well as its linkage device model. Pipe name when named pipe is communicated <Linkage=SANYO> Whether or not an automatic acquisition of a patient ID is made from the electronic medical chart at the time of starting a new study <Linkage=SANYO> Required cable response time-out value second when the pipe is connected <Linkage=SANYO> User name when the pipe is connected <Linkage=SANYO> Password when the pipe is connected <Linkage=SANYO> Interval [msec] for monitoring the common folder that checks requests for image display and study reservation/start, using the networking function. *Networking system = STANDARD

Setup Value

8.

Linkage with the Receipt Computer


Check No.
8-1 8-2 8-3 8-4 8-5 8-6 8-7 8-8 8-9

Name
Whether support is provided or not to linkage with the receipt computer. Device model linked to the receipt computer. Host name of receipt computer <Linkage=SANYO> Internet Protocol address of receipt computer <Linkage=SANYO> Port number for connecting to receipt computer <Linkage=SANYO> Cable format requesting patient information to receipt computer <Linkage=SANYO> Inquiry time-out value second <Linkage=SANYO> Preferential destination for patient information search <Linkage=SANYO> Shared folder for linkage with the receipt computer <Linkage= other than SANYO>

Setup Value
9-4 9-5 9-6 9-7

10. Image Incidental Information


Check No.
11-1

Name
Activation of the image processing modification flag

Setup Value

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

PC-4

PC-5 11. Print Format


Check No.
12-1 12-2 12-3 12-4 12-5 12-6 12-7 12-8 12-9

Check Name Setup Value

No.
12-19 12-20

Name
Film character area position and rotation when Osumi Film 1414-Single is formatted (default rule) Film character area position and rotation when Single is formatted onto B4 film (equal to 1014)

Setup Value

Type specification of film margin (blank part) Trimming volume [mm] (excluding Mammo) Whether or not there is a frame on the image when 18x24 Single is formatted 1417, 1414, 1843 / 810. Whether or not there is a frame on the image when 1417, 1843LR, 2on1 are formatted. Whether or not there is a frame on the image when 1417, 1843, 810, 4on1 are formatted. Whether or not there is a frame on the image when 2on1 display of L&R breast images on B4 film (equal to 1824) is formatted. Whether or not there is a frame in the 810 mammo Single image formatted onto B4 film. Whether or not there is a frame in the output image equal to 1824. Setting of menu code in which scale is not displayed (effective when setting is such that image frame is added).

Film character area position and rotation when Single is 12-21 formatted onto B4 film (equal to 1410 horizontal B4) (default rule) 12-22 12-23 12-24 Film character area position and rotation when LR on B4 film (equal to 1824) is formatted (default rule) Film character area position and rotation when 2 on 1 display on B4 film (equal to 1824) is formatted (default rule) Film character area position and rotation when 1012 size film and 2430-Single are formatted (default rule)

Film character area position and rotation when 10x12 size 12-25 film, 2430-Single (90 degree-rotation available) are formatted. (default rule) 12-26 Film character area position and rotation setting when halfsize Film 1417-Single/4on1 is formatted (user definition 1)

12-10 Specification of age display form 12-11 Specification of right and left reversing mark display form Whether or not film character area display is available when 12-12 1824-Single is formatted half-size Film 1417-Single/4on1, 1843-LR/2on1/4on1, 810-4on1 format, and 810 film size. 12-13 12-14 Film character area size when a film equal to 1417 size is output. Film character area position and rotation setting when halfsize Film 1417-Single/4on1 is formatted (default rule)

Film character area position and rotation setting when 12-27 Single/4on1 half-size Film 1714 (horizontal half-size)-is formatted (user definition 2) 12-28 Film character area position and rotation setting when halfsize Film 1843-LR/2on1/4on1 is formatted (user definition 3)

Film character area position and rotation setting when 12-29 1824-Single is formatted half-size Film 810-4on1 format and 810 film size format (user definition 4) 12-30 12-31 12-32 Position and rotation setting in film character area when image and film character area come in succession (user definition 5) Position and rotation setting in film character area when image and film character area come in succession (user definition 6) Image display position specification when 4343 Single is formatted half-size Film 1530 and 3535 (part display) Reduction ratio when 2 on 1 display of L&R breast images on B4 film (equal to 1824) is printed out.

Film character area position and rotation setting when 12-15 Single/4on1 half-size Film 1714 (horizontal half-size)-is formatted (default rule) 12-16 Film character area position and rotation setting when halfsize Film 1843-LR/2on1/4on1 is formatted (default rule)

12-33 Setting for validity/invalidity of reduced output onto a 810 film 12-34

Film character area position and rotation setting when 12-17 1824-Single is formatted half-size Film 810-4on1 format and 810 size film (default rule) Film character area position and rotation setting when 810 12-18 and 1824-Single (90 degree-rotation available) are formatted. (default rule)

Setting for Whether or not an expansion print is executed 12-35 when an image with the standard density format print is output.

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

PC-5

PC-6 12. Film Character Setting


Check No.
13-1 13-2 13-3 13-4 13-5 13-6 13-7 13-8 13-9 13-10

14. Operation (Low Frequency) Setting


Setup Value Check No.
15-1 15-2 15-3 15-4 15-5 15-6 15-7 15-8 15-9

Name
Whether or not EDR mode is displayed. Whether or not image processing conditions are displayed. Whether or not L value, S value, CS, and SS information are displayed. Whether or not exposure time is displayed. Whether or not routine and class processing information are displayed. Whether or not menu names are displayed. Whether or not compression code is displayed. Whether or not barcode is displayed. Setting for the maximum value of en-size character numbers for the patient names to be film-output. Setting for the maximum value of em-size character numbers for the patient names to be film-output. Setting for the maximum value of en-size character numbers for the exposure menu names to be filmoutput. Setting for the maximum value of em-size character numbers for the exposure menu names to be filmoutput. Activation of automatic generation function for film annotation character format.

Name
The maximum registration number of patient information The maximum registration number of study information Status acquisition timing of DICOM printer Timeout occurring prior to study termination Maximum number of markers Primary threshold warning system capacity Secondary threshold warning system capacity Warning threshold on system capacity Primary threshold warning database capacity

Setup Value

15-10 Secondary threshold warning database capacity 15-11 Warning threshold on database capacity 15-12 Minimum remaining capacity of local HDD

13-11 Setting for right/left justification of patient names. 13-12 13-13

15. Setting for Analysis


Check No.
19-1 19-2 19-3 19-4 19-5 19-6 19-7 19-8 19-9

Name
Log acquisition of DICOMPrintSCU communication Log acquisition of FRUPMain control communication Log acquisition of FRUP connection watch Log acquisition of FRUP image connection Trace log acquisition when image is output Log acquisition of DICOM verification SCU Log acquisition of DICOM storage SCU Collect image data for maintenance logs (For the number of studies) Arbitrary settings for acquisition of DICOM storage SCP log

Setup Value

13-14 Setting for right/left justification of the exposure menu names. 13-15

13. Setting for Output Function


Check No.
14-1

Name
Whether or not re-try has been executed after an abnormal output was made.

Setup Value

14-2 Status acquisition timing of DICOM printer 14-3 Arbitrary setting of DVD burning for storage 14-5 14-6
020-221-02E 01.08.2010 FM5563

19-10 Retrieve the log in MWM function

Whether annotation information will be embedded in the images for film output. Whether annotation information will be embedded in the images for general-purpose file output.

CR-IR 391CL Service Manual

PC-6

PC-7 16. Settings for Endoscopic Image Import


Check No.
20-1 20-2

20. Setting for DICOM-MWM


Check No.
25-1 25-2

Name
Support availability on endoscopic image import and the receiving system Receiving folder for endoscopic image import

Setup Value

Name
Whether support is provided or not to linkage with the MWM Server Preferential destination for patient information search, in the linkage with MWM Server

Setup Value

17. Electrocardiographic Data Import Settings


Check No.
21-1 21-2

Name
Data structure linked with the electrocardiograph (The data varies from maker to maker.) Folder in which on-line electrocardiographic data obtained from Fukuda Denshi electrocardiograph is stored in the form of folder path Folder dedicated for registration/management in which electrocardiographic data for display obtained from Fukuda Denshi electrocardiograph is stored Folder in which Fukuda Denshi electrocardiograph data that has been modified is temporarily stored for update at a later time Application path to link electrocardiogram

Setup Value

21-3

21-4 21-5

18. PDI Output Function Settings


Check No.
22-4 22-5 PDI write mode Compression of images (PDI)

Name

Setup Value

19. Free Layout Setting


Check No.
24-1

Name
Presence/Absence of Patient ID display

Setup Value

020-221-02E 01.08.2010 FM5563

CR-IR 391CL Service Manual

PC-7

PC-8
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PC-8

PC-9
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PC-9

PC-10
BLANK PAGE

020-221-01E 04.28.2009 FM5535

CR-IR 391CL Service Manual

PC-10

Das könnte Ihnen auch gefallen