Beruflich Dokumente
Kultur Dokumente
Chapter 2 Quiz
Due No due date Points 30 Questions 15 Time Limit None Allowed Attempts Unlimited
Instructions
This quiz covers the content in CCNA R&S Introduction to Networks Chapter 2. It is designed to provide an additional opportunity to practice the skills and knowledge presented in the chapter and to prepare for the Chapter Exam. You will be allowed multiple attempts and the grade does not appear in the gradebook. There are multiple task types that may be available in this quiz. Rather than having static graphics to view, some items may require you to open a PT activity and perform some investigation and configuration of devices before answering the question. NOTE: There are some small differences in how the questions score and operate in the Quiz and how they score and operate in the Chapter Exam. Quizzes allow for partial credit scoring on all item types to foster learning. Points on quizzes can also be deducted for answering incorrectly. This does not occur with the Chapter Exam. Form 26612
Attempt History
KEPT LATEST
Question 1
2 / 2 pts
to remove all configurations from the switch to save an active configuration to NVRAM
Correct!
to copy an existing configuration into RAM to make a changed configuration the new startup configuration
Refer to curriculum topic: 2.2.3 Usually, changes are made to a running configuration in RAM and copied to NVRAM. However, in this case, the technician wants to copy a previously saved configuration from NVRAM into RAM in order to make changes to it.
Question 2
0 / 2 pts
A technician configures a switch with these commands: SwitchA(config)# interface vlan 1 SwitchA(config-if)# ip address 192.168.1.1 255.255.255.0 SwitchA(config-if)# no shutdown What is the technician configuring?
Telnet access
Correct Answer
SVI
https://1370302.netacad.com/courses/72359/quizzes/155289
1/7
10/7/13
password encryption
You Answered
Refer to curriculum topic: 2.3.2 For a switch to have an IP address, a switch virtual interface must be configured. This allows the switch to be managed remotely over the network.
Question 3
0 / 2 pts
. Perform the tasks in the activity instructions and then answer the question or complete the task.
The address was statically assigned. PC0 does not have an IP address.
You Answered
Correct Answer
Refer to curriculum topic: 2.3.2 Click on the Desktop IP Configuration option. Verify that the DHCP radio button is enabled.
Question 4
0 / 2 pts
Which two statements are true regarding the user EXEC mode? (Choose two.)
Correct Answer
This is the default mode on an unconfigured router when first powered up. Interfaces and routing protocols can be configured.
You Answered
Correct Answer
Refer to curriculum topic: 2.1.3 User EXEC mode limits access to some show and debug commands. It is the first level of user interface when configuring a router and is intended for investigation of certain functions of the device.
Question 5
2 / 2 pts
https://1370302.netacad.com/courses/72359/quizzes/155289
2/7
10/7/13
Correct!
Refer to curriculum topic: 2.2.2 The enable secret command encrypts the password that is required for entering the privileged executive mode of a router or switch. Encrypting the password prevents the password from being saved in plain text in the configuration file.
Question 6
2 / 2 pts
a control panel
Correct!
Refer to curriculum topic: 2.1.1 Cisco IOS is the operating system that is used on Cisco network devices. For initial configuration, a network administrator cables to the console port and uses a terminal emulation application in order to access the IOS.
Question 7
0 / 2 pts
A network administrator has forgotten the argument of an IOS command. How would the administrator get help from the IOS CLI to complete the command correctly?
Type the command and then press the ? key. Type the command and then press the Tab key.
You Answered
Type the command, type help , and press the Enter key. Type the command and then press CTRL-C
Refer to curriculum topic: 2.1.4 In order to get help about a command argument, type the command and use the ? key (do not press the Enter key). For example, to get help about the argument of the ip address command, type the command followed by ? as shown: Router(config-if)# ip address ?
Question 8
https://1370302.netacad.com/courses/72359/quizzes/155289
0 / 2 pts
3/7
10/7/13
Fill in the blank. A mac address is defined as a reserved address that routes packets back to the host.
Answer 1:
You Answered
mac
Correct Answer Correct Answer Correct Answer Correct Answer Correct Answer Correct Answer Correct Answer Correct Answer Correct Answer
loop-back LOOP-BACK loopback LOOPBACK loop back LOOP BACK Loopback Loop back Loop Back
Refer to curriculum topic: 2.3.3 A loopback address is used to verify the internal IP configuration on a local host.
Question 9
0 / 2 pts
Why would a network administrator use the CLI of the Cisco IOS?
to add a password to a Cisco network device to provide automatic (unmanned) management of Cisco network devices
You Answered
to monitor the number of times a device has been powered on and off
Refer to curriculum topic: 2.1.1 IOS is the Cisco operating system that is found on Cisco network devices. The operating system is used to configure, monitor, and manage the network device.
Question 10
2 / 2 pts
To save time, IOS commands may be partially entered and then completed by typing which key or key combination?
Correct!
https://1370302.netacad.com/courses/72359/quizzes/155289
4/7
10/7/13
Up Arrow Right Arrow Down Arrow
Question 11
2 / 2 pts
Its maximum length is 255 characters. It must be registered with a DNS server. It cannot start with a number.
Correct!
Refer to curriculum topic: 2.2.1 A host name can include letters, digits, and dashes and must be contain fewer than 64 characters and cannot contain a space. It could be registered with a DNS server, but this is not a requirement.
Question 12
2 / 2 pts
Which device acts as a gateway to allow hosts to send traffic to remote IP networks?
Refer to curriculum topic: 2.3.2 For hosts to reach remote networks, they must send traffic to a local router that can route the traffic to the correct destination network. This local router is known as the default gateway and hosts must be configured with this address in order to communicate with devices on remote networks.
Question 13
0 / 2 pts
What command will prevent all unencrypted passwords from displaying in plain text in a configuration file?
You Answered
https://1370302.netacad.com/courses/72359/quizzes/155289
5/7
10/7/13
Refer to curriculum topic: 2.2.2 To prevent all configured passwords from appearing in plain text in configuration files, an administrator can execute the service password-encryption command. This command encrypts all configured passwords in the configuration file.
Question 14
2 / 2 pts
An administrator has just changed the IP address of an interface on an IOS device. What else must be done in order to apply those changes to the device?
Copy the running configuration to the startup configuration file. Copy the information in the startup configuration file to the running configuration. Reload the device and type yes when prompted to save the configuration.
Correct!
Nothing must be done. Changes to the configuration on an IOS device take effect as soon as the command is typed correctly and the Enter key has been pressed.
Refer to curriculum topic: 2.2.3 Changes to router and switch configurations take effect as soon as the command is entered. For this reason, it is very important that changes to live production devices are always carefully planned before being implemented. If commands are entered that render the device unstable or inaccessible, the device may have to be reloaded, resulting in network downtime.
Question 15
0 / 2 pts
Refer to the exhibit. Fill in the blank. Do not use abbreviations. What command does a technician issue on a switch to display the exhibited output? show
Answer 1:
You Answered
show
Correct Answer Correct Answer Correct Answer Correct Answer Correct Answer
show ip interface brief show ip interfaces brief SHOW IP INTERFACE BRIEF Show IP Interface Brief Show ip interface brief
Refer to curriculum topic: 2.3.3 The show ip interface brief command shows a summary of interface status for routers or switches.
https://1370302.netacad.com/courses/72359/quizzes/155289
6/7
10/7/13
Launch Chapter 2
Previous
Next
Chapter 2 Exam
https://1370302.netacad.com/courses/72359/quizzes/155289
7/7