Beruflich Dokumente
Kultur Dokumente
270 - 273
Radia Control Cards..........................................................274 - 275
Radia Incandescent Dimmers............................................276 - 278
Radia DC Modules.............................................................279 - 281
Radia FDB Modules...........................................................282 - 284
Radia Switch Modules.......................................................285 - 287
Radia Energy Management Modules...............................288 - 289
Radia Enclosures, Dividers and Power Supply Modules....290 - 293
Lutron Lighting Solutions..................................................294 - 295
LIGHTING CONTROLS
INTRODUCTION LIGHTING CONTROLS
AMX offers this high quality line of advanced lighting products designed to transform complex lighting requirements into
simplified, cost-effective solutions frequently used in commercial and industrial installations as well as in high rise residential
projects. AMX is also proud to offer Lutron products available as a convenience for AMX dealers.
SYSTEM DIAGRAM
Lights 1-6
Internet
Radia Eclipse
6 Dimmer Module
AMX NXA-ENET24
Managed Ethernet Switch
AMX NXT/D-1500VG-RGB
Touch Panel
Ethernet
Lighting
Lu tr o n Br o ch u r e
Wa n t t o s e e o u r li g h t i n g o p t i o n s
i n a c t i o n? J ust v is it h t t p :/ / www.
am x . co m /as s ets / lit e ra t u re /
T P. Br o ch u r e. p d f t o d o w n l o a d t h e
l a t e st l i t e ra t ure .
Lights
Lights
AMX ALD-HWD-6ND
Dimmer
AMX ALD-HWD-6ND
Dimmer
AMX ALD-HWD-5RL
Keypad
Internet
LAN Switch
AMX ALD-H48
Lighting Interface
AMX NXT/D-1500VG-RGB
Touch Panel
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 269
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.
LIGHTING CONTROLS
RE-DM4 SPECIFICATIONS
• Supports up to 4 Radia traditional dimmers and 2 specialty 2 at 200 mA @ 12 VDC with no additional power supply
CERTIFICATIONS
dimmers - including fluorescent, energy management switches
FCC, CE, UL North America, IEC-60950 Safety
and low power DC switching
ENVIRONMENTAL
• Operating Temperature: 0º to 40º C (32º to 104º F)
ONLINE www.amx.com/products/RE-DM4.asp
• Heat Dissipation (Typical): 300 BTU/hr single feed (2400 W);
600 BTU/hr dual feed (4800 W)
INCLUDED ACCESSORIES
• 2 4-pin 3.5mm captive wire connector (41-5047)
• 4 #8-32x1/2” F-point mounting screws
Pow e r D ev ic es
Li n e I n
Jumpe r
High Voltage Connections
L oad out
Neu tr al
C h o k es
Clas s 1 w ir ing
Clas s 2 w ir ing
D r y Clos ur es
Mounting Points
Lights 1-4
Radia RDM-2DC
Dual DC Dimmer Module
Radia Eclipse
4 Dimmer Module
Internet
AMX NXA-ENET24
Managed Ethernet Switch
Ethernet
Lighting
AMX NXT/D-1500VG-RGB
AxLink Touch Panel
AC Power
RDM Control
AMX NetLinx NI-2100
Ballast Control Integrated Controller
(back panel)
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 271
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.
LIGHTING CONTROLS
RE-DM6 SPECIFICATIONS
A good choice for larger businesses and residences needing 4-pin 3.5mm green captive wire connector - AxLink communication signaling
with 12VDC power in
support of up to 6 Radia traditional dimmers.
AUX POWER
2-pin 3.5mm green captive wire connector. This is a 12VDC power input that
FEATURES
supplies additional power to the Radia PCB and connected Radia modules.
• Custom preset configuration files - which can be saved and
DRY CONTACTS
reused in any installation - a huge time saver for programmers • Emergency fire alarm relay connection - Closed relay activates preset 126.
• Support for up to 768 dimmers/zones - a more than 8 fold Other control is locked out until relay opens. Supports daisy chaining of up to
increase over the previous generation 20 dimmers for this connection, with a maximum current requirement of
200mA when daisy-chained.
• Greater processing power for quicker preset recall - an even
• Failsafe connection - Works with a toggle switch - opening the switch triggers
better user experience preset 128, closing the switch triggers preset 127. Supports daisy chaining of
• RoHS compliance - an environmentally-friendly product up to 20 dimmers for this connection with a maximum current requirement of
• Each traditional dimmer - supports up to 1200 watts 200mA when daisy-chained.
• Supports up to 6 Radia traditional dimmers IDLE CURRENT DRAW
75 mA @ 120 VAC, 50 mA @ 240 VAC, 100 mA @ 13.5 VDC
ONLINE www.amx.com/products/RE-DM6.asp CERTIFICATIONS
FCC, CE, UL North America, IEC-60950 Safety
ENVIRONMENTAL
• Operating Temperature: 0º to 40º C (32º to 104º F)
• Heat Dissipation (Typical): 300 BTU/hr single feed (2400 W);
600 BTU/hr dual feed (4800 W)
INCLUDED ACCESSORIES
• 2 4-pin 3.5mm captive wire connector (41-5047)
• 4 #8-32x1/2” F-point mounting screws
Pow e r D ev ic es
Li n e I n
Jumpe r
High Voltage Connections
L oad out
Neu tr al
C h o k es
Clas s 1 w ir ing
Clas s 2 w ir ing
D r y Clos ur es
Mounting Points
Lights 1-6
Internet
Radia Eclipse
6 Dimmer Module
AMX NXA-ENET24
Managed Ethernet Switch
AMX NXT/D-1500VG-RGB
Touch Panel
Ethernet
Lighting
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 273
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.
LIGHTING CONTROLS
RDC-DC
Radia Control Card - 6-Channel Dimmer - Single Phase
120 VAC (FG606-01)
240 VAC (FG606-02)
277 VAC (FG606-03)
OVERVIEW SPECIFICATIONS
The RDC-DC 6-Channel Control Card module operates as a DIMENSIONS (HWD)
single-phase controller and can control up to six dimmable 10” x 2 3/4” (25.4 cm x 7 cm)
channels with six satellite connectors (for RDM series dimmer or WEIGHT
1.2 lbs (0.54 kg)
switching modules). Radia Dimmer Control Cards are the primary
LINE INPUT
building blocks of the Radia Lighting System. You’ll need one
• 120 VAC, 2W+G, 1Ø, 50/60 Hz, 50 mA
dimmer card for every six dimmer modules or switch Modules, • 240 VAC, 2W+G, 1Ø, 50/60 Hz, 25 mA
using the six digital control channels for precision dimming • 277 VAC, 2W+G, 1Ø, 50/60 Hz, 22 mA
or power control. Each Radia Dimmer Card acts as the Radia CONTROL INPUT
Lighting System brain and traffic manager. Each handles system • AxLink, PROlink, Eight dry closures
processing and non-volatile memory, coordinates the PROLink CONTROL OUTPUT
• Six control channels
and the ALink data networks and triggers functions from the
• Max. total current sourcing 300 mA @ 12 VDC
on board contact closure inputs. Everything is fully interactive
MOUNTING
between all networks. For example, if a preset is called by a Installs into one Radia Lighting Enclosure space
contact closure, all PROLink components and AxLink system COOLING
feedback will be updated at the same time. Convection-cooled; requires no fans
POWER
FEATURES • 120/240/277 VAC • 12 VDC (optional)
• Delivers digital dimming control to Radia Modules from six TORQUE TERMINALS
control ports, as well as onboard system processing, networking, To 20 in-lbs. (2.3 N/M)
and non-volatile preset memory MAX WIRE SIZE
10 AWG (4 mm²)
• Drives all channels using the same power phase
WIRE STRIPPING LENGTH
• Stores 128 onboard presets, each can use unique fade time
0.28” (7 mm)
• Ramps using programmable fade time, from 0 to 255 seconds
CONTROL CURRENT
• Provides up to 16 different dimming curves for precision control 300 mA for six ports
• Creates system-wide and zoned presets
ONLINE www.amx.com/products/RDC-DC.asp
M e m o r y P ro t e c t
Jumper
Mounting Points
Reset Button
RDC-PDC
Radia Pro Control Card - Dual or 3 Phase
120 VAC (FG606-04)
240 VAC (FG606-05)
OVERVIEW SPECIFICATIONS
The RDC-PDC Control Card module controls up to six dimmable DIMENSIONS (HWD)
channels with six satellite connectors (for RDM series dimmer or 10” x 2 3/4” (25.4 cm x 7 cm)
switching modules). It can split operation between two or three WEIGHT
1.5 lbs. (0.54 kg)
AC phases. Radia Dimmer Control Cards are the primary building
LINE INPUT
blocks of the Radia Lighting System. You’ll need one dimmer card
• 120 VAC, 2W+G, 1Ø, 50/60 Hz, 50 mA
for every six dimmer modules or switch modules, using the six • 240 VAC, 2W+G, 1Ø, 50/60 Hz, 25 mA
digital control channels for precision dimming or power CONTROL INPUT
control. Each Radia Dimmer Card acts as the Radia Lighting • AXlink, PROlink, Eight dry closures
System brain and traffic manager. Each handles system CONTROL OUTPUT
processing and non-volatile memory, coordinates the PROLink • Six control channels
• Max. total current sourcing 300 mA @ 12 VDC
and the AxLink data networks and triggers functions from the on
POWER INPUTS
board contact closure inputs. Everything is fully interactive
• Line 1 (channel 1 and 4) • Line 2 A (channel 5) • Line 2B (channel 2)
between all networks. For example, if a preset is called by a • Line 3 (channel 3 and 6) • Neutral
contact closure, all PROLink components and AxLink system MOUNTING
feedback will be updated at the same time. Installs into one Radia Lighting Enclosure space
COOLING
FEATURES Convection-cooled; requires no fans
• Delivers digital dimming control to Radia Modules from six POWER
control ports, as well as onboard system processing, networking, • 120/240 VAC • 12 VDC (optional)
and non-volatile preset memory TORQUE TERMINALS
To 20 in-lbs. (2.3 N/M)
• Drives channels using two or three power phases
MAX WIRE SIZE
• Stores 128 onboard presets, each can use unique fade time
10 AWG (4 mm²)
• Ramps using programmable fade time, from 0 to 255 seconds
WIRE STRIPPING LENGTH
• Provides up to 16 different dimming curves for precision control 0.28” (7 mm)
• Creates system-wide and zoned presets
ONLINE www.amx.com/products/RDC-PDC.asp
L E D in d ic a t o rs
Me m o r y P ro t e c t
Jumper
Mounting Points
Reset Button
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 275
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.
LIGHTING CONTROLS
RDM-INC
Incandescent Dimmer
Module - 2,400 W
(FG606-30)
OVERVIEW SPECIFICATIONS
The RDM-INC Incandescent Dimming Module is designed for DIMENSIONS (HWD)
use with the RDA series of enclosures, in a AMX Lighting modular 10” x 2 3/4” (25.4 cm x 7 cm)
digital dimming system. It is a standard 2400 W incandescent WEIGHT
3.7 lbs (1.7 kg)
dimmer. It can dim incandescent lights, cold-cathode, neon and
UL and C-UL Ratings
two-wire dimmable ballasts. The RDM-INC module’s 120, 240,
• 120 VAC, 50/60 Hz, 2400 W
and 277 VAC ratings are CE, UL, and C-UL approved. • 240/277 VAC, 50/60 Hz, 2400 W
SUGGESTED DIMMED LOADS
FEATURES • Incandescent
• 20 A Incandescent-compatible dimming • Low-voltage
• General-purpose switching, no positive air gap • Neon, cold-cathode
• Two-wire, phase-controlled ballast
• 40 A SCR, 350 microsecond rise time choke
WIRING
• Installs in one enclosure space
• Use wires rated at 75º C (167º F)
• Max. wire size: 10 AWG (4 mm²)
ONLINE www.amx.com/products/RDM-INC.asp • Wire stripping length: 0.28” (7 mm)
TORQUE TERMINALS
To 7 in-lbs (0.8 N/M)
CONTROL CURRENT
45 mA @ 12 VDC
CHOKE
350 µS Rise time @ 120 VAC, 175 µS Rise time @ 240 VAC
Mounting Points
L ine In (hot) Lo ad Ou t
RDM-2INC
Dual Incandescent Dimmer
Module - 2,400 W (x2)
(FG606-31)
OVERVIEW SPECIFICATIONS
The RDM-2INC Dual Incandescent Dimming Module 2400 W (x2) DIMENSIONS (HWD)
incandescent dimmer is designed for use with the RDA series of 10” x 2 3/4” (25.4 cm x 7 cm)
enclosures, in an AMX Lighting modular digital dimming system. WEIGHT
6.5 lbs (2.9 kg)
It can dim incandescent lights, cold-cathode, neon and two-wire
UL and C-UL Ratings
dimmable ballasts. The module’s 120, 240, and 277 VAC ratings
• 120 VAC, 50/60 Hz, 2400 W
are CE, UL, and C-UL approved. • 240/277 VAC, 50/60 Hz, 2400 W
SUGGESTED DIMMED LOADS
FEATURES • Incandescent
• Dual-channel 20 A Incandescent-compatible dimming • Low-voltage
• General-purpose switching • Neon, cold-cathode
• Two-wire, phase-controlled ballast
• Dual-channel 40 A SCR, 350 microsecond rise time chokes
WIRING
• Installs in one enclosure space
• Use wires rated at 75º C (167º F)
• Max. wire size: 10 AWG (4 mm²)
ONLINE www.amx.com/products/RDM-2INC.asp • Wire stripping length: 0.28” (7 mm)
TORQUE TERMINALS
To 7 in-lbs. (0.8 N/M)
CONTROL CURRENT
45 mA @ 12 VDC per dimmer, 90mA total
Mounting Points
L ine In (hot) Lo ad Ou t
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 277
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.
LIGHTING CONTROLS
RDM-INC50
Incandescent Dimmer
Module - 6,000 W
(FG606-32)
OVERVIEW SPECIFICATIONS
The RDM-INC50 Incandescent Dimmer Module is a standard DIMENSIONS (HWD)
6000 W incandescent dimmer. It can dim incandescent lights, 10” x 5 1/2” (25.4 cm x 13.97 cm)
cold-cathode, neon transformers and two-wire dimmable bal- WEIGHT
7 lbs (3.2 kg)
lasts. It is designed for use with the RDA series of enclosures, in a
UL and C-UL Ratings
AMX Lighting modular digital dimming system. The RDM-INC50
• 120 VAC, 6000 W
module’s 120, 240, and 277 VAC ratings are CE, UL, and C-UL • 240/277 VAC, 6000 W
approved. SUGGESTED DIMMED LOADS
• Incandescent
FEATURES • Low-voltage
• 50 A Incandescent-compatible dimming • Neon, cold-cathode
• Two-wire, phase-controlled ballast
• General-purpose switching, no positive air gap
WIRING
• 50 A SCR and 500 microsecond rise time choke
• Use wires rated at 75º C (167º F)
• Installs in two enclosure spaces • Max. wire size: 8 AWG (10 mm²)
• Wire stripping length: 0.28” (7 mm)
ONLINE www.amx.com/products/RDM-INC50.asp TORQUE TERMINALS
To 16 in-lbs (1.84 N/M)
CONTROL CURRENT
45 mA @ 12 VDC per dimmer
A CLOSER LOOK
Mounting Points
5 0 A Po we r D e v ic e
RDM-DC
DC Module - 1,920 W, 0-12 VDC
(FG606-60)
OVERVIEW SPECIFICATIONS
The RDM-DC Dimmer Module is a 1920 W module used for the DIMENSIONS (HWD)
dimming of fluorescent ballast loads. It uses a 0 to 10 VDC current 10” x 2 3/4” (25.4 cm x 6.99 cm)
sinking for use with four-wire ballasts. It is designed for use with WEIGHT
2.3 lbs (1.04 kg)
the RDA series of enclosures, in an AMX Lighting modular digital
UL and C-UL Ratings
dimming system. The module’s 120 and 277 VAC ratings are CE,
• 120 VAC, 50/60 Hz, 1920 W
UL, and C-UL approved. • 277 VAC, 50/60 Hz, 1920 W
• Control Out: 50 mA, 12 VDC sinking
FEATURES SUGGESTED DIMMED LOADS
• Dims one circuit DC-controlled electronic fluorescent ballasts Four-wire dimmable ballasts, like Advance Transformer Mark VII™ or the Energy
• Ramps 0-12 VDC signal for level control Savings SuperDim™ series
• One 20 A Positive air gap relays for power WIRING
• Use wires rated at 75º C (167º F)
• Current sinking
• Max. wire size: 10 AWG (4 mm²)
• Installs in one enclosure space • Wire stripping length: 0.28” (7 mm)
• Non-phase dependant TORQUE TERMINALS
To 20 in-lbs (2.3 N/M)
ONLINE www.amx.com/products/RDM-DC.asp CONTROL CURRENT
125 mA @ 12 VDC
Ballas t A Fu s es
A CLOSER LOOK
Mounting Points
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 279
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.
LIGHTING CONTROLS
RDM-2DC
Dual DC Module -
1,920 W (x2), 0-12 VDC
(FG606-61)
OVERVIEW SPECIFICATIONS
The RDM-2DC Dual DC Module is a 1920 W module used for the DIMENSIONS (HWD)
dimming of fluorescent ballast loads. It uses a 0 to 10 VDC current 10” x 2 3/4” (25.4 cm x 6.99 cm)
sinking for use with four-wire ballasts. It is designed for use with WEIGHT
2.3 lbs (1.04 kg)
the RDA series of enclosures, in an AMX Lighting modular digital
UL and C-UL Ratings
dimming system. The module’s 120 and 277 VAC ratings are CE,
• 120 VAC, 50/60 Hz, 1920 W
UL, and C-UL approved. • 277 VAC, 50/60 Hz, 1920 W
• Control Out: 50 mA, 12 VDC sinking
FEATURES SUGGESTED DIMMED LOADS
• Dims two circuits DC-controlled electronic fluorescent ballasts Four-wire dimmable ballasts, like Advance Transformer Mark VII™ or the Energy
• Ramps 0-12 VDC signal for level control Savings SuperDim™ series
• Dual 20 A Positive air gap relays for power WIRING
• Use wires rated at 75º C (167º F)
• Current sinking
• Max. wire size: 10 AWG (4 mm²)
• Installs in one enclosure space • Wire stripping length: 0.28” (7 mm)
TORQUE TERMINALS
ONLINE www.amx.com/products/RDM-2DC.asp To 20 in-lbs. (2.3 N/M)
CONTROL CURRENT
125 mA @ 12 VDC
Ballas t A Bal l as t B Fu s es
A CLOSER LOOK
Mounting Points
RDM-3DC
Triple DC Module -
1,920 W (x3), 0-12 VDC
(FG606-62)
OVERVIEW SPECIFICATIONS
The RDM-3DC Triple DC Module is a 1920 W module used for the DIMENSIONS (HWD)
dimming of fluorescent ballast loads. It uses a 0 to 10 VDC current 10” x 2 3/4” (25.4 cm x 6.99 cm)
sinking for use with four-wire ballasts. It is designed for use with WEIGHT
2.3 lbs (1.3 kg)
the RDA series of enclosures, in an AMX Lighting modular digital
UL and C-UL Ratings
dimming system. The module’s 120 and 277 VAC ratings are CE,
• 120 VAC, 50/60 Hz, 1920 W
UL, and C-UL approved. • 277 VAC, 50/60 Hz, 1920 W
• Control Out: 50 mA, 12 VDC sinking
FEATURES SUGGESTED DIMMED LOADS
• Dims three circuits DC-controlled electronic fluorescent ballasts Four-wire dimmable ballasts, like Advance Transformer Mark VII™ or the Energy
• Ramps 0-12 VDC signal for level control Savings SuperDim™ series
• Three 20 A Positive air gap relays for power WIRING
• Use wires rated at 75º C (167º F)
• Current sinking
• Max. wire size: 10 AWG (4 mm²)
• Installs in one enclosure space • Wire stripping length: 0.28” (7 mm)
TORQUE TERMINALS
ONLINE www.amx.com/products/RDM-3DC.asp To 20 in-lbs. (2.3 N/M)
CONTROL CURRENT
125 mA @ 12 VDC
Mounting Points
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 281
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.
LIGHTING CONTROLS
RDM-FDB
Single Channel FDB Module -
1,920 W
(FG606-65)
OVERVIEW SPECIFICATIONS
The RDM-FDB Single Channel Ballast Dimmer is a 1920 W DIMENSIONS (HWD)
positive air gap relay and dimmer, built for strength and for 10” x 2 3/4” (25.4 cm x 6.99 cm)
reliable switching/dimming of Lutron FDB ballasts. It is designed WEIGHT
11.52 oz (327 g)
for use with the RDA series of enclosures, in a AMX Lighting
UL and C-UL Ratings
modular digital dimming system. The RDM-FDB module’s 120,
• 120 VAC, 1920 W
240, and 277 VAC ratings are CE, UL, and C-UL approved. • 240/277 VAC, 1920 W
SUGGESTED DIMMED LOADS
FEATURES • Most 3-wire dimmable fluorescent ballasts
• Single channel ballast dimmer for reliable switching/dimming • Lutron© Hi-Lume® FDB Ballasts
of Lutron FDB Ballasts • Lutron Eco-10® Ballasts
• 1920 W positive air gap relay and dimmer WIRING
• Use wires rated at 75º C (167º F)
• Installs in one enclosure space
• Max. wire size: 10 AWG (4 mm²)
• For use with FDB ballasts • Wire stripping length: 0.28” (7 mm)
• Dimmed output protected by a 250 mA GMA 5 x 20 mm fuse TORQUE TERMINALS
• Phase dependant To 20 in-lbs (2.3 N/M)
CONTROL CURRENT
ONLINE www.amx.com/products/RDM-FDB.asp 85 mA @ 12 VDC
Ballas t A Fu s e
A CLOSER LOOK
Mounting Points
RDM-2FDB
Dual Channel FDB Module -
1,920 W (x2)
(FG606-66)
OVERVIEW SPECIFICATIONS
The RDM-2FDB Dual Channel Ballast Dimmer is a 1920 W positive DIMENSIONS (HWD)
air gap relay and dimmer, built for strength and for reliable 10” x 2 3/4” (25.4 cm x 6.99 cm)
switching/dimming of Lutron FDB ballasts. It is designed for use WEIGHT
1.5 lbs (680 g)
with the RDA series of enclosures, in a AMX Lighting modular
UL and C-UL Ratings
digital dimming system. The RDM-2FDB module’s 120, 240, and
• 120 VAC, 1920 W
277 VAC ratings are CE, UL, and C-UL approved. • 240/277 VAC, 1920 W
SUGGESTED DIMMED LOADS
FEATURES • Most 3-wire dimmable fluorescent ballasts
• Dual channel ballast dimmer for reliable switching/dimming • Lutron© Hi-Lume® FDB Ballasts
of Lutron FDB Ballasts • Lutron Eco-10® Ballasts
• 1920 W positive air gap relay and dimmer WIRING
• Use wires rated at 75º C (167º F)
• Installs in one enclosure space
• Max. wire size: 10 AWG (4 mm²)
• For use with FDB ballasts • Wire stripping length: 0.28” (7 mm)
• Dimmed output protected by a 250 mA GMA 5 x 20 mm fuse TORQUE TERMINALS
• Phase dependant To 20 in-lbs (2.3 N/M)
CONTROL CURRENT
ONLINE www.amx.com/products/RDM-2FDB.asp 85 mA @ 12 VDC
Ballas t A Bal l as t B Fu s e
A CLOSER LOOK
M ounting Points
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 283
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.
LIGHTING CONTROLS
RDM-3FDB
Triple Channel FDB Module - 1,920 W (x3)
(FG606-67)
OVERVIEW SPECIFICATIONS
The RDM-3FDB Triple Channel Ballast Dimmer is a 1920 W DIMENSIONS (HWD)
positive air gap relay and dimmer, built for strength and for 10” x 2 3/4” (25.4 cm x 6.99 cm)
reliable switching/dimming of Lutron FDB ballasts. It is designed WEIGHT
1.57 lbs (712 g)
for use with the RDA series of enclosures, in an AMX Lighting
UL and C-UL Ratings
modular digital dimming system. The RDM-3FDB module’s 120,
• 120 VAC, 1920 W
240, and 277 VAC ratings are CE, UL, and C-UL approved. • 240/277 VAC, 1920 W
SUGGESTED DIMMED LOADS
FEATURES • Most 3-wire dimmable fluorescent ballasts
• Triple channel ballast dimmer for reliable switching/dimming • Lutron© Hi-Lume® FDB Ballasts
of Lutron FDB Ballasts • Lutron Eco-10® Ballasts
• 1920 W positive air gap relay and dimmer WIRING
• Use wires rated at 75º C (167º F)
• Installs in one enclosure space
• Max. wire size: 10 AWG (4 mm²)
• For use with FDB ballasts
TORQUE TERMINALS
• Dimmed output protected by a 250 mA GMA 5 x 20 mm fuse To 20 in-lbs (2.3 N/M)
CONTROL CURRENT
ONLINE www.amx.com/products/RDM-3FDB.asp 85 mA @ 12 VDC
Mounting Points
RDM-SWM
Switch Module - 20 A
(FG606-50)
OVERVIEW SPECIFICATIONS
The RDM-SWM Switch Module is a 2400 W general purpose relay DIMENSIONS (HWD)
module built for economical switching of incandescent lamps, 10” x 2 3/4” (25.4 cm x 6.99 cm)
low-voltage transformers, switched fans and electrical outlets. It WEIGHT
8 oz (227 g)
is designed for use with the RDA series of enclosures, in an AMX
POWER
Lighting modular digital dimming system. The RDM-SWM uses a
• 120/240/277 VAC
positive air gap type relay. This module’s 120, 240, and 277 VAC
UL AND C-UL RATINGS
ratings are CE, UL, and C-UL approved. • General purpose: 2400 W
• Resistive: 2400 W
FEATURES • Ballast: 2400 W
• 20 A positive air-gap relay • Motor: 277 VAC, 1 hp
• General-purpose switching applications SUGGESTED SWITCHED LOADS
• Incandescent
• Installs in one enclosure space
• Low-voltage
• Motors
ONLINE www.amx.com/products/RDM-SWM.asp • Switched outlets
• Fluorescent
WIRING
• Use wires rated at 75º C (167º F)
• Max. wire size: 10 AWG (4 mm²)
• Wire stripping length: 0.28” (7 mm)
TORQUE TERMINALS
To 7 in-lbs (.8 N/M)
CONTROL CURRENT
85 mA @ 12 VDC
Mounting Points M o u n t in g Po in t s
Line In (hot) L i n e Ou t
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 285
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.
LIGHTING CONTROLS
RDM-2SWM
Dual Switch Module - 20 A
(FG606-51)
OVERVIEW SPECIFICATIONS
The RDM-2SWM Dual Switch Module is a 20 A general-purpose DIMENSIONS (HWD)
relay module built for the economical switching of incandescent 10” x 2 3/4” (25.4 cm x 6.99 cm)
lamps, switched low-voltage transformers, switched fans, and WEIGHT
12 oz (340 g)
small motors. It uses positive air gap relays. The RDM-2SWM is
POWER
designed for use with the RDA series of enclosures, in an AMX
120/240/277 VAC
Lighting modular digital dimming system. This module’s 120, 240,
UL AND C-UL RATINGS
and 277 VAC ratings are CE, UL, and C-UL approved. • General purpose: 2400 W
• Resistive: 2400 W
FEATURES • Ballast: 2400 W
• Two 20 A positive air-gap relay • Motor: 277 VAC, 1 hp
• General-purpose switching applications SUGGESTED SWITCHED LOADS
• Incandescent
• Installs in one enclosure space
• Low-voltage
• Non-phase dependant • Motors
• Switched outlets
ONLINE www.amx.com/products/RDM-2SWM.asp • Fluorescent
WIRING
• Use wires rated at 75º C (167º F)
• Max. wire size: 10 AWG (4 mm²)
• Wire stripping length: 0.28” (7 mm)
TORQUE TERMINALS
To 7 in-lbs (.8 N/M)
CONTROL CURRENT
85 mA per relay (170mA total) @ 12 VDC
Mounting Points M o u n t in g Po in t s
Line In (hot) Li n e Ou t
RDM-3SWM
Triple Switch Module - 20 A
(FG606-52)
OVERVIEW SPECIFICATIONS
The RDM-3SWM Triple Switch Module is a 20 A triple general DIMENSIONS (HWD)
purpose relay module built for compact and economical switching 10” x 2 3/4” (25.4 cm x 6.99 cm)
of incandescent lamps, switched low-voltage transformers, WEIGHT
1 lb (453 g)
switched fans and electrical outlets. It is designed for use with
POWER
the RDA series of enclosures, in an AMX Lighting modular digital
120/240/277 VAC
dimming system. The RDM-3SWM uses positive air gap type
UL AND C-UL RATINGS
relays. This module’s 120, 240, and 277 VAC ratings are CE, UL, • General purpose: 2400 W
and C-UL approved. • Resistive: 2400 W
• Ballast: 2400 W
FEATURES • Motor: 277 VAC, 1 hp
• Three 20 A positive air-gap relay SUGGESTED SWITCHED LOADS
• Incandescent
• General-purpose switching applications
• Low-voltage
• Installs in one enclosure space • Motors
• Non-phase dependant • Switched outlets
• Fluorescent
ONLINE www.amx.com/products/RDM-3SWM.asp WIRING
• Use wires rated at 75º C (167º F)
• Max. wire size: 10 AWG (4 mm²)
• Wire stripping length: 0.28” (7 mm)
TORQUE TERMINALS
To 7 in-lbs (.8 N/M)
CONTROL CURRENT
85 mA per relay (255mA total) @ 12 VDC
Mounting Points M o u n t in g Po in t s
Line In (hot) L i n e Ou t
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 287
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.
LIGHTING CONTROLS
RDM-3EM
Heavy Duty Energy Management
Relay Module - 20 A
(FG606-81)
OVERVIEW SPECIFICATIONS
The RDM-3EM is a 3 channel switching energy management DIMENSIONS (HWD)
module. It is designed for use with the RDA series of enclosures 10” x 2 3/4” (25.4 cm x 6.99 cm)
in an AMX Lighting system. The RDM-3EM is designed with the WEIGHT
15 oz (425 g)
most advanced latching energy management relays to support
POWER
heavy duty commercial applications, building automation, and
120/240/277 VAC
loadside management. Equipped with on-board module
UL AND C-UL RATINGS
microprocessors, both support relay control and sequencing. • General purpose: 120, 240, 277, and 347* VAC, 20 A
• UL/CUL916 Energy Management Systems
FEATURES • UL/CUL508 Industrial Control Systems
• Three 20 A relays - non-phase dependent SUGGESTED SWITCHED LOADS
current and stress on the electrical distribution system • Use wires rated at 75º C (167º F)
• Max. wire size: 26 to 10 AWG
• Selectable strapping facilitates multiple relays on one Radia
• Wire stripping length: 0.28” (7 mm)
control channel for large area control
TORQUE TERMINALS
• Manual on/off override on each relay independent of control system To 4.4 in-lbs
• Relays retain their state during power and control system outages INCLUDED ACCESSORIES
• Visual status indicators on each relay • 4 mounting screws
• Latching relays do not consume any control current, except • Control wiring harness
when they change state, eliminating the need for additional
Radia power supplies
ONLINE www.amx.com/products/RDM-3EM.asp
Re la y s (1 -3 ) S eq u en ci n g Del ay Ju m p er s (JP 1 - JP 2 )
A CLOSER LOOK
Mounting Points M o u n t in g Po in t s
C o n tr o l Po r t S tr ap p i n g Ju m p er s (JP 3 - JP 4 )
RDM-6EM
Heavy Duty Energy Management
Relay Module - 20 A
(FG606-80)
OVERVIEW SPECIFICATIONS
The RDM-6EM is a 6 channel switching energy management DIMENSIONS (HWD)
module. It is designed for use with the RDA series of enclosures 10” x 2 3/4” (25.4 cm x 6.99 cm)
in an AMX Lighting system. The RDM-3EM is designed with the WEIGHT
1.5 lbs (680 g)
most advanced latching energy management relays to support
POWER
heavy duty commercial applications, building automation, and
120/240/277 VAC
loadside management. Equipped with on-board module
UL AND C-UL RATINGS
microprocessors, both support relay control and sequencing. • General purpose: 120, 240, 277, and 347* VAC, 20 A
• UL/CUL916 Energy Management Systems
FEATURES • UL/CUL508 Industrial Control Systems
• Six 20 A relays - non-phase dependent SUGGESTED SWITCHED LOADS
current and stress on the electrical distribution system • Use wires rated at 75º C (167º F)
• Max. wire size: 26 to 10 AWG
• Selectable strapping facilitates multiple relays on one Radia
• Wire stripping length: 0.28” (7 mm)
control channel for large area control
TORQUE TERMINALS
• Manual on/off override on each relay independent of control system To 4.4 in-lbs
• Relays retain their state during power and control system outages INCLUDED ACCESSORIES
• Visual status indicators on each relay • 4 mounting screws
• Latching relays do not consume any control current, except • Control wiring harness
when they change state, eliminating the need for additional
Radia power supplies
ONLINE www.amx.com/products/RDM-6EM.asp
Re la y s (1 -6 ) S eq u en ci n g Del ay Ju m p er s (JP 1 - JP 2 )
A CLOSER LOOK
Mounting Points M o u n t in g Po in t s
C o n tr o l Po r t S tr ap p i n g Ju m p er s (JP 3 - JP 7 )
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 289
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.
LIGHTING CONTROLS
RDA-ENC2
Radia Lighting 2 Space Enclosure
(FG606-10)
RDA-ENC4
Radia Lighting 4 Space Enclosure
(FG606-11)
RDA-ENC6
Radia Lighting 6 Space Enclosure
(FG606-12)
RDA-PSM RDA-DIV
12 VDC 2.5 A Power Supply Radia Module Divider
Module (FG606-18)
(FG606-90)
OVERVIEW OVERVIEW
The RDA-PSM Power Supply is a 30 W module providing an un- The RDA-DIV Radia Module Divider separates 110 modules from
regulated output of 12 VDC at 2.5 Amps. The power supply module 277/240 Modules in Radia Lighting Enclosures.
is designed for use with the RDA series of Radia enclosures. The
RDA-PSM is used to supply extra power to Radia control cards FEATURES
when the amount of power required to drive the modules exceeds • Separates 110 from 277/240 Modules in Radia Lighting Enclosure
the 300 mA supply on each controller. The module’s voltage and • Use if required by local code
current ratings are CE, UL, and C-UL approved.
ONLINE www.amx.com/products/rda-div.asp
FEATURES
• Provides 12 VDC, 2500 mA power to Radia Lighting Cards and Modules
• Unregulated, class one power supply
• Installs in one enclosure space
• Non-phase dependant
• Provides 2500 mA to drive RDM modules RDA-EFP
• Dual 2-pin connectors provided
Radia Enclosure Filler Plate
• Fuse rating: GMA 1 A
(FG606-19)
ONLINE www.amx.com/products/RDA-PSM.asp
SPECIFICATIONS
DIMENSIONS (HWD)
10” x 2 3/4” x 6” (25.4 cm x 6.99 cm)
WEIGHT
2 lbs (910 g)
POWER
12 VDC
OVERVIEW
UL AND C-UL RATINGS
• Output: 12 VDC @ 2.5 A output The RDA-EFP Radia Enclosure Filler Plate fills open spaces in
• Input: 120 VAC Radia Lighting Enclosures.
WIRING
• Use wires rated at 75º C (167º F) FEATURES
• Max. wire size: 10 AWG (4 mm²) • Required to fill open spaces in Radia Lighting Enclosures
• Wire stripping length: 0.35” (9 mm)
• Installs in one enclosure space
TORQUE TERMINALS
To 16 in-lbs. (1.84 N/M)
ONLINE www.amx.com/products/RDA-EFP.asp
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 291
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.
LIGHTING CONTROLS
RDA-ENC6B
Radia Lighting 6 Space Enclosure
with 6 Breakers
120 VAC (FG606-13)
240 VAC (FG606-15)
OVERVIEW SPECIFICATIONS
The RDA-ENC6B enclosure provide secure mounting for AMX DIMENSIONS (HWD)
Lighting and PROLink controllers, and lighting modules. The 24” x 18” x 6” (60.7 cm x 45.7 cm x 15.2 cm)
enclosure also contain 6 circuit breakers. This enclosure is CE, UL, DIMENSIONS FROM CENTER LINES
• A to B = 16.0” (40.6 cm)
and C-UL approved. It includes circuit breakers and terminals for
• B to C = 22.88” (58.1 cm)
multi-phase wiring. It also provides 18 knockouts for 1/2”, 3/4”,
WEIGHT
and 1” conduits. 16.5 lbs (7.5 kg)
CONFIGURATIONS
FEATURES • ENC6B/120: 20 A Breakers
• Supports multi-phase wiring for one RDC-PDC Dimmer Card • ENC6B/240: 10 A Breakers
• Includes six 20A circuit breakers and terminals for multi- LINE INPUTS
A CLOSER LOOK
RDA-ENC12B
Radia Lighting 6 Space Enclosure
with 12 Breakers
120 VAC (FG606-14)
240 VAC (FG606-16)
OVERVIEW SPECIFICATIONS
The RDA-ENC12B enclosure provide secure mounting for DIMENSIONS (HWD)
AMX Lighting and PROLink controllers, and lighting modules. The 24” x 18” x 6” (60.7 cm x 45.7 cm x 15.2 cm)
enclosure also contain 12 circuit breakers. This enclosure is CE, DIMENSIONS FROM CENTER LINES
• A to B = 16.0” (40.6 cm)
UL, and C-UL approved. It includes circuit breakers and terminals
• B to C = 22.88” (58.1 cm)
for multi-phase wiring. It also provides 18 knockouts for 1/2”, 3/4”,
WEIGHT
and 1” conduits. 17.5 lbs (7.94 kg)
CONFIGURATIONS
FEATURES • ENC12B/120: 20 A Breakers
• Supports multi-phase wiring for one RDC-PDC Dimmer Card • ENC12B/240: 10 A Breakers
• Supports multi-phase wiring for one RDC-PDC Dimmer Card LINE INPUTS
• Includes 12 20A circuit breakers and terminals for multi- • 140 A max per enclosure
• Input 1 feeds channels 1, 4, 7, and 10
phase wiring
• Input 2a feeds channels 5 and 11
• Provides six spaces for Radia Lighting Modules • Input 2b feeds channels 2 and 8
• Mounts RDC-PDC card in dedicated, pre-wired compartment • Input 3 feeds channels 3, 6, 9, and 12
• 18 knockouts for 1/2”, 3/4”, and 1” conduit • Breakers are UL 489 listed 10,000 AIC, 100% Switching Duty,
Hydraulic-Magnetic
• Supports up to 18 dimming channels per unit (3 RE-DM6)
WIRING
• Maximum input wire #1/0 AWG (50mm²)
ONLINE www.amx.com/products/RDA-ENC12B.asp
• Maximum line input is 140 A (per enclosure )
• Torque input wire to 44 in-lbs. (5.0 N/m)
• Wire stripping length: 0.67 inches (17 mm)
A CLOSER LOOK
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 293
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.
LIGHTING CONTROLS
3000 R E S EARCH D RIVE, RICH ARDSON, TX 75082 • 800.222.0193 • 469.624.7 1 5 3 f a x • TEC H NI C A L S U PPORT 8 0 0 . 9 3 2 . 6 9 9 3 295
© May 2009 AMX. All rights reserved. AMX does not assume responsibility for any errors or omissions.