Beruflich Dokumente
Kultur Dokumente
CAD TUTOR
Basic Functions of Mold Base Parts ~ Injection Mold Design Tutorial, Technology and Engineering
MISUMI MOLD STANDARD PART MOLD BASE RESOURCE
SOCIAL PROFILES
ARTICLE TAG
Assembly
cooling
Mold
Clamping core
basic
cavity force
construction
gate film
ejector system
gate flat cooling
gate
and
6 1 0 9 1 9
POPULAR POSTS
How to Calculate Clamping force as we know clamping unit purpose is to keep mold closed against force when part injected with plastic material, because of that clamping for... Construction Injection Molds Classification classification or types of mold injection very depend on what we need to make the plastic parts, because every parts have specific and uniqu... Basic Functions of Mold Base Parts A mold plate is any plate required to built a complete mold, in all plate use for molds have the main requirements, they are : 1. Good corro... Plastic Processing Methode Types Today, they are various plastic processing method available in industrial process, from the method of processing plastic we can divided into...
Mold
mold plate
Runner
runner system
runner
balance
layout
setting
runner
Shrinkage side gate sink mark sleeve ejector slider parts Sprue Sprue
of the molding
bush
undercut Wall
warpage weld line
Thickness
explanation below based on number at those picture 1. Fixed Clamping Plate or Top Plate Holds The fixed side of the mold to attached at the fixed platen of the injection machine. at this plate will attach locating ring, eye bolt, and sprue bush. 2. Runner Stripper Plate this plate only used in 3 plate molds type, the function is to cut resin from nozzle in top of sprue bush, and pull the runner by runner locking pin. 3. Fixed Mold Plate or Cavity plate. use to hold cavity side of product, leader pin, support pin, Puller bolts, and Angular pin when slider attached. 4. Movable Cavity Plate or Cavity plate it used to attach core side of product, return pin, leader bush and slider core if needed. 5. Back up Plate or Support plate used to support cavity plate, attach the hole for return pin's spring, and cooling channel when in cavity plate can not make it. 6. Spacer Block Mounted between the movable clamping plate (bottom plate) and the movable cavity plate to give space and allow the ejector plate to move when ejecting the part. the required length of spacer block depend on ejector stroke that needed to
shringkage of mold calculation, mold calculator as the request, lot of people need engineering and calculation of injection mold and mold design, so i try to make little software, the name... Opening Construction of 3 Plate Mold Type previous post http://mouldtechnology.blogspot.com/2008/08/mainconstruction-pin-at-3plate-mold.html we can see closed condition of three ...
Runner system, flowing part of plastic injection After material injected by nozzle, runner systems will convey the molten material from the sprue to the gate. basic runner system consist of...
http://mould-technology.blogspot.com/2008/02/basic-functions-of-mold-base-parts.html
1/3
8/3/2014
eject product. 7.Ejector retainer plate
Basic Functions of Mold Base Parts ~ Injection Mold Design Tutorial, Technology and Engineering
Loose core for ejecting undercut at injection mold Picture above shows the loose core, or often also called slope ejectors or inclined pin, loose cores is one method to overcome the undercu... wall thickness and sink mark estimation Uniform wall thickness in plastic part design is critical.Non-uniform wall thickness can cause serious warpage and dimensional control probl... Top 6 Injection Molding Company it's difficult to list all company that provide any solution about injection machine, include manufacturer, injection molder, machine ma...
to hold the ejector, Z pin, shoulder bolts,and give space to ejector leader pin and support pillar. 8. Ejector Plate Pushes the ejector pins and return pins, connected with ejector rods. 9. Movable Clamping Plate or Bottom plate Holds The movable side of the mold like spacer block, support plate, cavity plate and ejector mechanism to the movable platen of the injection machine.
and look at picture below, shown 3 plate molds type in opening position, but at picture below, Bottom plate or movable clamping plate is number 7, number 8 is ejector retainer plate, and number 9 is ejector plate.
New er Post
Home
Older Post
7 comments:
tnutman says:
September 20, 2010 at 7:46 PM
thank you
Reply
tarik says:
April 18, 2012 at 3:26 AM
Aiman says:
April 24, 2012 at 5:21 PM
Aiman says:
April 24, 2012 at 5:21 PM
nice
http://mould-technology.blogspot.com/2008/02/basic-functions-of-mold-base-parts.html
2/3
8/3/2014
Reply
Basic Functions of Mold Base Parts ~ Injection Mold Design Tutorial, Technology and Engineering
Nice blog and attractive information. I like your blog and your work. thanks, Rahul Injection Molded Components
Reply
AcmeDisys says:
August 28, 2013 at 10:52 PM
I really appreciated with it, This is fine to read and valuable pro potential, I really bookmark it, pro broaden read. Appreciation pro sharing. I like it. injection mold equipments | Plastic Injection Mould |
Reply
Post a Comment
Copyright 2006 Injection Mold Design Tutorial, Technology and Engineering | Powered by Blogger
Design by New WpThemes.com | Bloggerized by Lasantha - Premium Blogger Themes Bluehost Hosting
http://mould-technology.blogspot.com/2008/02/basic-functions-of-mold-base-parts.html
3/3