Beruflich Dokumente
Kultur Dokumente
Edition 01/2011 PERI GmbH Formwork Scaffolding Engineering P .O. Box 1264 89259 Weissenhorn Germany Tel. +49 (0)7309.950 - 0 Fax +49 (0)7309.951- 0 info@peri.com www.peri.com
Important Notes:
Without exception, all current safety regulations must be observed in those countries where our products are used. The illustrations in this brochure are photographs of real site situations. Safety or anchor details are therefore not to be taken as a denitive guide to the way the equipment is to be used. Safety precautions and allowable loads are to be strictly observed at all times. Separate structural calculations are required for any deviations from the standard design data. The information contained herein is subject to technical changes in the interests of progress. Errors and typographical mistakes reserved.
Contents
2 4 6 8
Climbing Systems CB 240 and CB 160 Type-tested safety at all heights For all heights and every ground plan With VARIO GT 24, MAXIMO, TRIO or RUNDFLEX Construction-compliant load assumptions, simple formwork adjustment Wind loads, over-sized formwork elements Even platform planking, Formwork Carriage CB 240 CB 240 climbing cycle sequence Type-tested safety measures, moving procedure of the CB 160 Certified scaffolding anchoring High level of working safety with system components BR shaft platforms Application, support, details Tables Load Tables and Charts CB 160 Load tables and Charts CB 240
10 12 14 16
18 20
22
24 26
28 48
CB climbing scaffold system with type tests provide high levels of safety in all areas of application. With the CB 240, the formwork is mounted on a carriage with roller bearings and can be moved by approx. 75 cm. This means sufcient space is available for cleaning the formwork and reinforcement work. The 2.40 m wide platform planking is ush with the Carriage CB and free of any tripping hazards. With the CB 160, the formwork is simply tipped backwards for striking. For both systems, the formwork is moved together with the scaffold in only one crane lift.
Test Type
CB 240 and CB 160 are type-tested. This makes time-consuming static calculations unnecessary.
Photo on the right Bridge pier Architectural concrete with CB 240 and VARIO GT 24.
Environmental construction High-quality architectural concrete with CB 240 brackets and VARIO GT 24.
Hotel construction CB 240 scaffold brackets complete with nishing platform and TRIO.
CB 240 Safe working areas and access with system components on the formwork and CB climbing scaffold.
30-storey apartment building CB 240 and CB 160 scaffold brackets with VARIO GT 24.
LNG liquid gas tanks Circular walls 77.50 m with CB 240 and VARIO GT 24.
Adapter TRIO/CB
Tension Anchor CB
Tension Anchor CB Handrail Post 370 Platform Post 225 Handrail Post 370 Platform Post 225
Airport control tower 46 m high, external 6,85 m. With PERI RUNDFLEX and CB 240 brackets.
CB 240
Formwork carriage in working position Concreting platform 150 kg/m2 Formwork carriage in concreting postition Concreting platform 150 kg/m2
CB 160
300 kg/m2
Simple adjustment of the formwork elements for neat and tidy concrete joints
Precise adjustment of the angle of inclination. With Adjustable Brace CB 164-224.
Move element sideways. By releasing the Strongback Connector U 100-120. For MAXIMO and TRIO With Adapter TRIO-CB
Wind loads
CB 240 and CB 160 are type tested and designed to handle high wind speeds. CB 240 and CB 160 type tests are available on request from PERI. The PERI CB 240 provides type-tested wind safety at any position which means: Locking the formwork on the carriage takes place quickly and securely by means of a wedge. Complete safety against the wind immediately after mounting the tie rod.
Wind forces increase accordingly with the height. The DIN 1055, which forms the basis for the design, determines the wind loads according to wind zones, ground proles and operating heights.
150
Wind loads for shoring according to EN 12812
600
Wind dynamic pressure for transition zone inland and with load reduction factor* for period of application < 24 months. * = 0.7
350
hS
hG
ZO
100
1,80
QO
ne
ne
ne
Zo
Zo
Zo
ne
nd
ind
ind
Wi
50
in
hS
DU
Zo
ZZ
0
0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30
Wind dynamic pressure [kN/m2]
10
hS/2
Extremely long platforms are also no problem with the CB 240 and CB 160. Instead of the usual square-shaped timbers, GT 24 girders can be used as platform main beams. With a double GT 24 girder position, platform lengths of up to maximum 12.00 m are possible.
max. 5.40 m
CB 240 with nishing platform and VARIO GT 24 for construction of LNG gas tanks.
11
12
Carriage CB 240
With roller bearings for easy shuttering and striking. This means that large formwork elements can also be easily moved forwards and backwards. 75 cm working area when the formwork is retracted This creates sufcient space for cleaning the formlining as well as installing the reinforcement.
Ratchet Lever SW 19
Rack drive
Securing wedge
Formwork Carriage
Roller bearings
Bracket CB 240
75 cm
With the captive wedge, the carriage can be xed in any moving position.
The Carriage CB 240 is moved using the Ratchet Lever SW 19, Item no. 027180.
13
1. The rst wall section is concreted. Install the leading anchor according to specications.
2. After reaching the required concrete strength, mount the Scaffold Mounting Ring M24 and then attach the pre-assembled scaffold unit. Install the formwork and concrete the second section.
3. Retract the formwork and then mount the Scaffold Mounting Ring M24.
14
4. Lift the complete unit to the next section by means of the crane. If required, the nishing platform can be tted. Note: Load-bearing capacity of the crane eye on the Strongback CB is 1.9 t.
5. Reinforcement work is now carried out and, if required, the formwork is placed at an angle.
6. Move the formwork forwards and concrete. At this point. cycles continue as in Point 3.
15
Climbing System CB Type-tested safety measures, moving procedure of the CB 160 and climbing traverse
Safe working conditions also on the CB 160 climbing system. An integrated ladder allows safe and secure access to the nishing platform.
CB 160
CB 240
Combining CB 160 and CB 240 is the cost-effective solution for high walls.
16
The PERI Climbing Traverse RCS 10 t, Item no. 112986, is used when moving larger or non-symmetrical units.
Use a guide rope to ensure that the moving preocedure is fully under control.
17
With climbing systems, safety is signicantly determined through the quality of the tie system. Therefore, PERI tie systems are approved by the building authorities. The PERI Climbing Anchor M24/DW 15 and M24/DW 20 are efcient in their use as well as guaranteeing safe handling.
Lost components
Variant 1 Standard anchoring with variable anchoring depth. With PERI Climbing Cone-2 M24/DW 15 Building Authority Approval No. Z-21.6-1767
M24/ DW 15 M24x120-10.9 Scaffold Mounting Climbing Cone-2 Tie Rod DW 15 Item no. 030030 M24/DW15 Item no. 029560 Ring M24 Item no. 029470 Item no. 031220 Threaded Anchor Plate 15 Item no. 030840
Variant 2 Anchoring for thin walls and limited anchor forces. With PERI Screw-On Cone-2 M24/DW 20 Building Authority Approval No. Z-21.6-1766
M24/ DW 20 M24x120-10.9 Item no. 029560 Scaffold Mounting Screw-On Cone-2 M24/DW 20 Ring M24 Item no. 029470 Item no. 030960 Threaded Anchor Plate 20 Item no. 030860
Variant 1 With PERI Climbing Cone-2 M24/DW 15 and Threaded Anchor Plate 15.
Variant 2 With PERI Screw-On Cone-2 M24/DW 20 and Threaded Anchor Plate 20.
450
CB 240
350
CB 160
18
2. Attach scaffold suspension Remove Advancing Bolt M24. Retract formwork. Attach Scaffold Mounting Ring M24 with Hex. Bolt M24 x 120.
2. Attach scaffold suspension Release the formwork from the concrete and retract (the nails are pulled through the plywood). Dismantle Anchor Positioning M24 using a pin wrench SW 14. Mount Scaffold Mounting Ring M24 using a Hex. Bolt M24 x 120.
3. Mount scaffold brackets Mount Scaffold Brackets CB 240 or CB 160 and immediately secure by means of safety pins.
5. Close anchor points The remaining anchor hole is closed by means of the Concrete Cone KK. This results in an opticallypleasing concrete surface. 4. Reusable anchor components Screw out the Hex. Bolt M24 x 120 and cone from the nishing platform using the socket wrench SW 36.
19
The system components for the CB 240 and CB 160 climbing systems provide a very high degree of safety. Integrated ladders with hinged hatches and ladder cages ensure safe access to the nishing and concreting platforms. Handrail post for xing the end and side handrails.
Using VARIO platforms, the CB 240 climbing system ensures safe access to the concreting level.
Accessing the two nishing platforms is carried out with CB 240 and CB 160 system components.
20
Access ladder Safe and secure access to the CB 240 and CB 160 nishing platform at all heights.
B
Sliding or hinged hatches
A) Side handrail post For xing end handrails. It is mounted on the outer main beam at the end.
B) End handrail post With larger cantivers, it is attached to the outer main beam.
21
Application
Table of permissible bearing forces for gravity pivot plate Concrete cube Concrete cylin- perm. vertical der strength bearing load strength [N/mm2] [kN] [N/mm2] 10.0 12.0 14.0 16.0 18.0 19.1 8.0 9.6 11.2 12.8 14.4 15.3 20.0 23.9 27.9 31.9 35.9 38.0 Reinforcement Diameter of against tensile reinforcement [mm] splitting BST 500 [cm2] 0.15 0.18 0.21 0.24 0.27 0.29 1x5 1x5 1x6 1x6 1x6 1x8
Note: For suspension of the nishing platforms, only use Tie Rods B15 or Scaffold Tube 48.3 mm.
Considered tolerances: Clear width of the shaft 20 mm. Length of platform beam 3 mm. Clearance in the box out + 10 mm. Remaining supporting depth min. 27 mm.
22
70
442
25 115
327
Note: The external platform beam (timber) may not obstruct the unhindered folding of the gravity pivot plate.
max. 100 mm timber Hook Strap HB 24-100/120 for Prole U 100 / U 120 Hook Strap HB 24-140/160 for Prole U 140 / U 160 Hook Strap HB for Prole U 100 / U 120 Hook Strap HB2 for Prole U 140 / U 160
Drilled hole 20
80
23
Load Combination B Storm With higher wind loads, the permissible widths of inuence must be reduced accordingly and the bearing forces determined through a static calculation. Width of inuence b Application height hG Formwork height hS Formwork weight max. 60 kg/m2 Wind ow pressure q Aerodynamic wind factor cW = 1.3 Wind load: q = 0.8 kN/m2 q = 1.1 kN/m2 q = 1.3 kN/m2
hS
The charts are for detailed determination of the bearing reactions whilst taking into account realistic load combinations. For all load combinations (A working and B storm), the safe transfer of the bearing forces into the building structure has to be veried.
v = 72 km/h
hS/2 hG ZO QO 1.80 DU hS ZZ Wind from the front Wind from the rear Storm B1 133 kg/m2 from the front Storm B2 133 kg/m2 from the rear Storm B3 from the rear
Working on all platforms is allowed. Material storage on the working platform is allowed.
Load assumptions
Platform Platform width [m] Dead load of the platform [kg/m] 30 30 50 50 Permissible live load* [kg/m] 150 150 200 75 Decisive load combinations [kg/m] for calculating the bearing reactions Working A 75 kg/m2 200 kg/m2 37.5 kg/m2 from the front
Concreting platform Intermediate platform** Working platform Finishing platform Wind direction **if necessary
* Maximum permissible live load for operating condition Working . Loads are evenly distributed. One-sided loading of cantilevered platform areas is not permitted. Working: if loading of several platform levels, only one level can be fully loaded all other platform levels only up to 50%. Storm: Reduced load on the working platform for material left behind.
24
600
Load Tables and Charts CB 160 Bearing reactions for the permissible width of inuence (perm. b)
max. wind ow pressure during storm Load case q = 0.8 kN/m2 hS perm. b QO A ZO DU QO B1 ZO DU QO B2 Z O* ZZ QO B3 Z O* ZZ 3.00 m 6.55 m 47.2 kN 30.6 kN 23.8 kN 34.7 kN 51.7 kN 32.2 kN 44.8 kN -25.6 kN 11.8 kN 39.4 kN -29.2 kN 18.7 kN 4.00 m 4.40 m 36.9 kN 26.2 kN 20.2 kN 28.6 kN 49.1 kN 31.9 kN 44.0 kN -23.9 kN 16.8 kN 40.5 kN -25.8 kN 21.3 kN 5.40 m 2.90 m 28.1 kN 23.0 kN 17.7 kN 22.6 kN 47.8 kN 32.6 kN 44.0 kN -21.9 kN 22.5 kN 41.8 kN -22.8 kN 25.4 kN 3.00 m 5.55 m 40.4 kN 26.1 kN 20.3 kN 29.9 kN 56.9 kN 34.1 kN 45.0 kN -31.8 kN 17.6 kN 40.4 kN -34.8 kN 23.5 kN q = 1.1 kN/m2 4.00 m 3.60 m 30.9 kN 21.7 kN 16.8 kN 24.1 kN 52.9 kN 33.5 kN 43.8 kN -28.0 kN 21.6 kN 41.0 kN -29.5 kN 25.3 kN 5.40 m 2.40 m 23.9 kN 19.3 kN 14.9 kN 19.3 kN 52.7 kN 35.4 kN 45.5 kN -25.5 kN 27.4 kN 43.7 kN -26.2 kN 29.9 kN 3.00 m 5.05 m 37.1 kN 23.8 kN 18.6 kN 27.5 kN 59.7 kN 35.2 kN 45.2 kN -35.1 kN 20.6 kN 41.0 kN -37.8 kN 26.0 kN q = 1.3 kN/m2 4.00 m 3.25 m 28.3 kN 19.7 kN 15.3 kN 22.1 kN 55.4 kN 34.7 kN 44.3 kN -30.4 kN 24.2 kN 41.7 kN -31.7 kN 27.5 kN 5.40 m 2.05 m 21.0 kN 16.6 kN 12.9 kN 17.1 kN 52.5 kN 35.1 kN 44.2 kN -26.0 kN 28.4 kN 42.6 kN -26.6 kN 30.5 kN
*if ZO < 0, then a compressive force affects the anchorage. intermediate values can be interpolated linear. Maximum values are in bold. Load factor wind loads: Load Combination A = 1.0. Load Combination B = 0.9
The permissible widths of inuence correspond to the type test. The bearing reactions differ to the type test, because the type test does not distinguish between different operating conditions. The calculation of types according to current standards is being prepared.
Formulae to calculate the forces for actual width of inuence (actual b) QO (actual b) = actual b perm. b actual b perm. b actual b perm. b actual b perm. b (QO (perm. b) - 3.8 kN) + 3.8 kN
ZO (actual b) =
DU (actual b) =
ZZ (actual b) =
ZZ (actual b)
5.00
q = 0.8 kN/m2
q = 1.1 kN/m2
3.00 2.00
3.00
4.00
5.00
6.00
7.00
25
The charts are for detailed determination of the bearing reactions whilst taking into account realistic load combinations. For all load combinations (A working and B storm), the safe transfer of the bearing forces into the building structure has to be veried. With higher wind loads, the permissible widths of inuence must be reduced accordingly and the bearing forces determined through a static calculation. Width of inuence b Application height hG Formwork height hS Formwork weight max. 60 kg/m Wind ow pressure q Aerodynamic wind factor cW = 1.3
v = 72 km/h
hS/2 hG hS 450 ZO 1.80 QO hS DU ZZ Wind from the front Wind from the rear Storm B1 133 from the front Storm B2 133 from the rear Storm B3 from the rear
The formwork is retracted (75 cm), or is in the concreting position. Working on all platforms is permitted. Storage of materials on the working platform is permitted. Load combination B storm Wind load: q = 0.8 kN/m2 q = 1.1 kN/m2 q = 1.3 kN/m2
Formwork in concreting position Working not permitted Material can be left on the working platform.
Platform
Decisive load combinations [kg/m] for calculating the bearing reactions Working A 75 300 200 37.5 from the front
Concreting platform Intermediate platform (if required) Working platform Wall side Guardrail side Finishing platform Wind direction
* Maximum permissible live load for operating condition Working . Loads are evenly distributed. One-sided loading through cantilevered platform areas is not permitted. Working: if loading several platform levels, only one level can be fully loaded all other platform levels only up to 50%. Storm: reduced load on the working platform for material left behind.
26
600
Load tables and charts CB 240 Bearing reactions for permissible widths of inuence (perm. b)
max. wind ow pressure Load case q = 0.8 kN/m2 hS perm. b QO A ZO DU QO B1 ZO DU QO B2 Z O* ZZ QO B3 Z O* ZZ 3.00 m 4.80 m 48.8 kN 39.1 kN 34.1 kN 33.6 kN 46.9 kN 32.6 kN 33.6 kN -14.3 kN 0.0 kN 27.4 kN -20.3 kN 9.4 kN 4.00 m 3.90 m 44.2 kN 38.4 kN 33.1 kN 31.8 kN 51.1 kN 35.8 kN 37.2 kN -18.6 kN 6.3 kN 32.2 kN -22.3 kN 13.3 kN 5.40 m 3.16 m 39.3 kN 38.6 kN 32.8 kN 29.3 kN 58.3 kN 41.8 kN 42.3 kN -22.4 kN 14.3 kN 38.3 kN -24.6 kN 19.7 kN 3.00 m 4.28 m 44.0 kN 35.1 kN 30.7 kN 30.3 kN 52.2 kN 34.7 kN 34.1 kN -20.7 kN 4.9 kN 28.6 kN -26.1 kN 13.4 kN q = 1.1 kN/m2 4.00 m 3.40 m 39.1 kN 33.8 kN 29.2 kN 28.3 kN 56.8 kN 38.5 kN 38.0 kN -24.3 kN 11.4 kN 33.7 kN -27.5 kN 17.5 kN 5.40 m 2.68 m 34.0 kN 33.1 kN 28.2 kN 25.5 kN 64.4 kN 45.2 kN 43.3 kN -27.3 kN 19.5 kN 39.9 kN -29.2 kN 24.1 kN 3.00 m 3.95 m 40.9 kN 32.6 kN 28.5 kN 28.3 kN 54.6 kN 35.5 kN 34.1 kN -23.9 kN 7.6 kN 29.0 kN -28.9 kN 15.4 kN q = 1.3 kN/m2 4.00 m 3.12 m 36.3 kN 31.2 kN 27.0 kN 26.3 kN 59.7 kN 39.8 kN 38.2 kN -27.2 kN 14.0 kN 34.3 kN -30.1 kN 19.6 kN 5.40 m 2.50 m 32.1 kN 31.1 kN 26.5 kN 24.1 kN 69.4 kN 48.2 kN 44.9 kN -30.7 kN 22.9 kN 41.8 kN -32.4 kN 27.1 kN
*if ZO < 0, a compressive force then affects the anchorage. Intermediate values can be linear interpoliert. Maximum values are in bold. Load factor wind loads: Load combination A = 1.0. Load Combination B = 0.9
The permissible widths of inuence correspond to the type test. The specied bearing reactions differ to those of the type test because no differentiation between several operating conditions are given there. The type calculation according to current standards is being prepared.
Formulae to calculate values for actual width of inuence (actual b) QO (actual b) = actual b perm. b actual b perm. b actual b perm. b actual b perm. b (QO (actual b) - 4.6 kN) + 4.6 kN
ZO (actual b) =
DU (actual b) =
ZZ (actual b) =
ZZ (perm. b)
3.00 2.00
2.50
3.00
3.50
4.00
4.50
5.00
27
1100
440
228 2411
051020
33,900
Carriage CB 240 For mounting to the Climbing Bracket CB 240. Can be assembled in 2 positions: for platform beams with Girder GT 24 or timber 8 x 16 cm.
1800
1175
625
250
027180 051040
1,760 8,440
28
165 / 245
90
3214
33
64
051010
0,930
Lifting Eye CB 240, galv. For mounting to the Climbing Bracket CB 240 when used as a working platform.
Complete with 1 x 018050 Pin 16 x 65/86, galv. 1 x 018060 Cotter Pin 4/1, galv. Safety instructions Load-bearing point: lifting capacity 700 kg.
73
62
051100
79,000
Complete with 2 x 017040 Screw-On Coupling AK 48, galv. 1 x 715977 Handrail Post CB 240 1 x 710222 Hex, Bolt ISO 4014 M16 x 80-8.8, galv. 1 x 070890 Nut ISO 7042 M16-8, galv. Note Delivery condition: handrail post attached to transportation bracket.
50 630 440
228 30 1521
140
1025
440
1606
1800
3135
10
30
29
SW 19
260
83
051120
4,560
Platform Connection CB 160 For connection of platform decking to the Climbing Bracket CB 160 for use as working scaffold.
Complete with 2 x 711078 Hex. Bolt ISO 4014 M20 x 130-8.8, galv. 2 x 781053 Nut ISO 7042 M20-8, galv. Safety instructions Load-bearing point: load capacity 500 kg.
70
130
90
051060 051150
73,400 103,000
Strongback CB Strongback CB 270 Strongback CB 380 For mounting of system formwork to the Climbing Brackets CB 240 and CB 160. For formwork heights up to 5.40 m.
Complete with 1 x 715936 Pin with Tension Sleeve 1 x 018060 Cotter Pin 4/1, galv. Safety instructions Load-bearing point: load capacity 1.9 t.
120
196 86
90 / 160
30
240 7 x 60 = 420
2730 / 3800
1430
235
55
237
240
max 182
25
SW 19 60 55 190
051110
25,000
Complete with 2 x 715936 Pin with Tension Sleeve 2 x 018060 Cotter Pin 4/1, galv.
1580
min 1640
max 2240
051090
13,500
Adapter TRIO-CB For the connection of TRIO panels to the Strongback CB. Horizontal or vertical use is possible. With built-in height adjustment.
Complete with 1 x 715936 Pin with Tension Sleeve 1 x 018060 Cotter Pin 4/1, galv. Note Spanner size SW 19.
SW 19
89
25
100
415
82
180
400
31
80 - 145 284
80
126
76 120
107007
3,410
Tension Anchor Connector CB For securing against tilting due to wind loads using DW 15 Tie Rod.
Complete with 1 x 710219 Hex. Bolt ISO 4014 M16 x 100-8.8, galv. 1 x 070890 Nut ISO 7042 M16-8, galv.
400
M 16x100 DW 15
30
107008
4,100
Wall Tension Connector For securing against tilting due to wind loads using DW 15 Tie Rod.
Complete with 1 x 027170 Pin 16 x 42, galv. 1 x 018060 Cotter Pin 4/1, galv.
26
100
180
64
60
DW 15
50 100 331
255
026430 051260
0,334 3,300
Accessories Hex. Bolt ISO 4014 M24 x 70-10.9 Belt Connector CB For securing against tilting due to wind loads with Tension Belt. Complete with 1 x 710219 Bolt ISO 4014 M16 x 100-8.8, galv. 1 x 070890 Nut ISO 7042 M16-8, galv.
400
20
M 16x100
25
32
59
60
25
100
80
12
026430 026430
0,334 0,334
Accessories Hex. Bolt 4014 M24 x 70-10.9 Hex. Bolt ISO 4014 M24 x 70-10.9 High tensile bolt for the anchoring of climbing systems. Note Spanner size SW 36.
70
SW 36
M24
051250
2,790
051230
17,000
Complete with 4 x 710232 Hex. Bolt ISO 4014 M16 x 130-8.8, galv. 4 x 070890 Nut ISO 7042 M16-8, galv.
232 965 86
12
50
16
965 1230
249
80
17
150
M 16x130
270
80
33
M 16x130
86
200
30
1750
1000
22 85
710
17
200
051050
26,400
Post Extension CB 180 For mounting finishing platforms. In combination with Platform Post CB 225 for concreting heights from 3.60 m up to 5.40 m.
Complete with 2 x 710232 Hex. Bolt ISO 4014 M16 x 130-8.8, galv. 2 x 070890 Nut ISO 7042 M16-8, galv.
200
20
30
200
M 16x130
500
500
200
995 1300
17
800
34
20
200
86
30
M 16x130
1125
500 280
17
460 80 80
M 16x130 9
200
500
820
200
051210 051220
19,000 34,600
Handrail Post CB Handrail Post CB 190 Handrail Post CB 370 For assembling guardrails to the finishing platforms. Handrail Post CB 190 for concreting heights up to 3.60 m. Handrail Post CB 370 for concreting heights from 3.60 m up to 5.40 m.
Complete with 2 x 710232 Hex. Bolt ISO 4014 M16 x 130-8.8, galv. 2 x 070890 Nut ISO 7042 M16-8, galv.
200
30
30
1895 / 3695
2155 / 3955
80
80
17
30
200
330
80
440
440
N x 500
60
385
440
440
2225
35
L
48,3x3,2
017010
1,400
(27)
SW 19
017040
0,850
( 12)
SW 19
051160
0,894
48
60
SW 19
024140
0,033
36
95
9 7 50 100 340
051640 051630
0,014 11,000
Accessories Hex. Wood Screw DIN 571 6 x 80, galv. End Handrail Post For assembling of handrails on larger cantilevers. Screwed to platform main beam.
190
9 7 120
40 1270 230
110 30 50 280
051640 051640
0,014 0,014
Accessories Hex. Wood Screw DIN 571 6 x 80, galv. Hex. Wood Screw DIN 571 6 x 80, galv. Note Spanner size SW 10.
80
190
440
440
50
SW 10
37
1360
560
max 417
1020
400
051650
0,060
M8, galv. M8 x 100 MU, galv. M8 x 125 MU, galv. M8 x 180 MU, galv.
B 80 115 28
M6/M8 SW 10 / SW 13
029470
0,723
Scaffold Mounting Ring M24, galv. Anchoring System M24. For anchoring climbing systems.
73
029560
0,535
38
73
17 / 21
L B
17
24
120 M24 SW 36
114158
1,030
Screw-On Cone-2 M24/DW 20, galv. Anchoring System M24. For anchoring of climbing systems.
Note Permissible load: see PERI product information. Spanner size SW 36.
150
DW 20
SW 36
65
M 24
030860 030860
0,801 0,801
Accessories Threaded Anchor Plate DW 20 Threaded Anchor Plate DW 20 For the use with Tie Rod DW 20, B 20 or Screw-On Cone-2 M24/DW 20. For anchoring into the concrete. Note Permissible load: see PERI product information. Lost anchor component.
031220
1,010
Climbing Cone-2 M24/DW 15, galv. Anchoring System M24. For anchoring of climbing systems.
Note Permissible load: see PERI product information. Spanner size SW 36.
100 SW 36 25
DW 15
50
Accessories Threaded Anchor Plate DW 15 Tie Rod DW 15 special length Tie Rod B 15 special length Threaded Anchor Plate DW 15 For use with Tie Rod DW 15 or B 15. For anchoring in concrete. Note Permissible load: see PERI product information. Lost anchor component.
60 6
80
27
DW 15
M 24 70
70
39
030740 030050
1,550 0,000
Note Weldable! Observe construction approval! Technical data Permissible load 85 kN.
B 15
029270
0,331
Advancing Bolt M24, galv. For connecting Anchor System M24 if the formlining can be drilled through.
70 M 24 SW 19
029280 029280
0,196 0,196
Accessories Anchor Positioning Plate M24, galv. Anchor Positioning Plate M24, galv. For connecting Anchor System M24 if the formlining can be drilled through.
7 25
60
029440
0,005
40
80
026420
0,123
Anchor Positioning Stud M24, galv. For mounting Anchor System M24 if the plywood is not drilled through.
SW 14 5 M 24 40
Accessories Allen Key SW 14, long Wire nails 3 x 80 Ladder 180/6, galv. For accessing PERI formwork systems. Complete with 4 x 710224 Hex. Bolt ISO 4017 M12 x 40-8.8, galv. 4 x 710381 Nut ISO 7042 M12-8
60
83
051420
12,800
Complete with 4 x 710224 Hex. Bolt ISO 4017 M12 x 40-8.8, galv. 4 x 710381 Nut ISO 7042 M12-8
400
3 x 298 = 894 2265
450
450
41
170
13,5
423
051460
2,180
Ladder Base, galv. As bottom end piece and for preventing the ladders sliding on platform decking.
405
210
50
103718
0,684
Ladder Hook, galv. To adjust the lower ladder. Always use in pairs.
Complete with 2 x 710266 Hex. Bolt ISO 4017 M12 x 25-8.8, galv. 2 x 710381 Nut ISO 7042 M12-8
330
104132 051450
15,600 25,200
Ladder Safety Cage Ladder Safety Cage 75, galv. Ladder Safety Cage 150, galv. Safety cage for PERI access ladders.
Complete with 4 px 710266 Hex. Bolt ISO 4017 M12 x 25-8.8, galv. 4 x 701763 Clamping Plate Fl 25 x 10 x 90
0 - 320
SW 18
525
710
750 / 1500
42
704
730
550 1140
830
103
110608
15,600
Hatch 55 x 60, foldable Self-closing hatchway for ladder access. Clear opening dimensions approx. 55 x 60 cm.
386
6 550 662
560
60
600 820
710
027180
1,760
795
031480
2,460
510
43
230
Platform Beam BR Platform Beam BR U100 Platform Beam BR U120 Platform Beam BR U140 Platform Beam BR U160 As cross beam for shaft platforms.
Note The specified item no. applies only to the 2 Platform Beam profiles. The required accessories are to be ordered separately. Permissible load: see PERI Design Tables.
700
700
700
700
L
50 50
52
115
273
54
123
Accessories Spacer for Platform Beam BR Crane Eye BR 2.5 t Folding Bearing Plate 25 Gravity Pivot Plate BR Spacer por Platform Beam BR For Platform Beam BR. Complete with 1 x 710226 Hex. Bolt ISO 4014 M20 x 90-8.8, galv. 1 x 781053 Nut ISO 7042 M20-8, galv. Note Spacing; maximum 700 mm. Number according to length of the Platform Beam. Spanner size SW 30.
52
M 20x90 SW 30
105401
2,210
Crane Eye BR 2.5 t As attachment point for moving climbing systems or Platform Beam BR.
135
60 100 75
245
15
020620
0,561
44
50
65
75
48
70
70 M 24
108162 108162
1,610 1,610
Accessories Bearing Box BR Bearing Box BR To create wall box-outs for supporting with the Gravity Pivot Plate.
140
029270 020330
0,331 12,100
Accessories Advancing Bolt M24, galv. Folding Bearing Plate 25 For supporting the Platform Beam BR with the Anchor System M24. 2 pieces per platform beam. Technical data Permissible load 25.0 kN.
258 234 50
170
210
162
25
026430
0,334
291
350
140
52
80
45
30
45
82
024080
0,676
Hook Strap HB 24-140/160, galv. For mounting GT 24 Girders to Steel Walers SRZ and SRU, Profile U140 - U 160.
M 8x70
82
Tie Rod B 15 Tie Rod B 15 special length Cutting Costs DW 15, B 15 Tie Rod B 15 l = 0.30 m
Note Weldable! Observe construction approval! Technical data Permissible load 85 kN.
B 15
030370
1,560
Wingnut Pivot Plate DW 15, galv. With articulated, captive nut. Maximum angle of inclination of the anchors 8.
117
72
10
030070
0,222
Hex. Nut DW 15 SW 30/50, galv. For anchoring with Tie Rod DW 15.
46
M 24
Accessories Cone for Anchor Sleeve M24 Plug 26 mm for Anchor Sleeve M24 Cone for Anchor Sleeve M24 Results in a concrete covering of 24 mm.
39 24
026250
0,005
Plug 26 mm for Anchor Sleeve M24 For closing Cones for Anchor Sleeve M24.
27
31
50
026430
0,334
Hex. Bolt ISO 4014 M24 x 70-10.9 High strength bolt for anchoring climbing systems.
70
26
SW 36
M24
23
31
12
47
PERI International
42
19 20
22 18
32 34 38
44
11 52 6 21 1 17 2 3 9 24 53 4 48 41 61 33 12 16 29 30 13 28 46
02 France PERI S.A.S. 77109 Meaux Cedex peri.sas@peri.fr www.peri.fr 03 Switzerland PERI AG 8472 Ohringen info@peri.ch www.peri.ch 04 Spain PERI S.A. 28110 Algete - Madrid info@peri.es www.peri.es 05 Belgium/Luxembourg N.V. PERI S.A. 1840 Londerzeel info@peri.be www.peri.be 06 Netherlands PERI B.V. 5480 AH-Schijndel info@peri.nl www.peri.nl
09 Italy PERI S.p.A. 20060 Basiano info@peri.it www.peri.it 10 Japan PERI Japan K.K. Tokyo 103-0015 info@perijapan.jp www.perijapan.jp 11 United Kingdom/Ireland PERI Ltd. Rugby, CV23 0AN info@peri.ltd.uk www.peri.ltd.uk 12 Turkey PERI Kalp ve skeleleri Esenyurt / stanbul 34510 info@peri.com.tr www.peri.com.tr 13 Hungary PERI Kft.. 1181 Budapest info@peri.hu www.peri.hu
16 Austria PERI Ges.mbH 3134 Nudorf ob der Traisen ofce@peri.at www.peri.at 17 Czech Republic PERI spol. s r.o. 252 42 Jesenice u Prahy info@peri.cz www.peri.cz 18 Denmark PERI Danmark A/S 2670 Greve peri@peri.dk www.peri.dk 19 Finland PERI Suomi Ltd. Oy 05460 Hyvink info@perisuomi. www.perisuomi. 20 Norway PERI Norge AS 3036 Drammen info@peri.no www.peri.no 21 Poland PERI Polska Sp. z o.o. 05-860 Pochocin info@peri.pl.pl www.peri.pl.pl 22 Sweden PERIform Sverige AB 30013 Halmstad peri@periform.se www.periform.se
23 Korea PERI (Korea) Ltd. Seoul 135-080 info@perikorea.com www.perikorea.com 24 Portugal PERIcofragens Lda 2790-326 Queijas info@peri.pt www.peri.pt 25 Argentina PERI S.A. B1625GPA Escobar Bs. As. info@peri.com.ar www.peri.com.ar 26 Brazil PERI Formas e Escoramentos Ltda. Vargem Grande Paulista So Paulo info@peribrasil.com.br www.peribrasil.com.br 27 Chile PERI Chile Ltda. Colina, Santiago de Chile peri.chile@peri.cl www.peri.cl 28 Romania PERI Romnia SRL 077015 Baloteti info@peri.ro www.peri.ro
29 Slovania PERI Slowenien 2000 Maribor peri.slo@triera.net www.peri.com 30 Slovakia PERI spol. s r.o. 903 01 Senec info@peri.sk www.peri.sk 31 Australia PERI Australia Pty. Ltd. Glendenning NSW 2761 info@periaus.com.au www.periaus.com.au 32 Estonia PERI AS 76406 Saku vald Harjumaa peri@peri.ee www.peri.ee 33 Greece PERI Hellas Ltd. 194 00 Koropi info@perihellas.gr www.perihellas.gr 34 Latvia PERI SIA 2118 Salaspils novads, Rigas rajons info@peri-latvija.lv www.peri-latvija.lv 35 United Arab Emirates PERI (L.L.C.) Dubai perillc@perime.com www.perime.com
14 Malaysia 07 USA PERI Formwork Malaysia PERI Formwork Systems, Inc. Sdn. Bhd. Elkridge, MD 21075 43300 Seri Kembangan, info@peri-usa.com Selangor Darul Ehsan www.peri-usa.com info@perimalaysia.com www.perimalaysia.com 08 Indonesia PT Beton Perkasa Wijaksana 15 Singapore Jakarta 10210 PERI ASIA Pte. Ltd bpw@betonperkasa.com Singapore 387355 www.peri.com pha@periasia.com www.periasia.com
48
36
44
43 7 50 39 49 60 47 37 40 57 56 58 51 54 59 35 66 55 23 10
63
65 14 15 8 62 26 64
27 45 25
31
42 Iceland 36 Canada Armar ehf. PERI Formwork Systems, Inc. 220 Hafnarfjrur Bolton, ON L7E 1K1 www.armar.is info@peri.ca www.peri.ca 43 Kazakhstan TOO PERI Kazakhstan 37 Lebanon 050014 Almaty Lebanon Representative Ofce peri@peri.kz Jdeideh www.peri.kz lebanon@peri.de www.peri.de 44 Russian Federation OOO PERI 38 Lithuania 142407, Noginsk District PERI UAB moscow@peri.ru 02300 Vilnius www.peri.ru info@peri.lt www.peri.lt 45 South Africa Wiehahn Formwork and 39 Morocco Scaffolding (Pty) Ltd. PERI S.A. 7600 Stellenbosch Tanger info@wiehahn.co.za peri25@menara.ma www.wiehahn.co.za www.peri.com 40 Israel PERI Formwork Engineering Ltd Petach Tikva, 49002 info@peri.co.il www.peri.co.il 41 Bulgaria PERI Bulgaria EOOD 1839 Soa peri.bulgaria@peri.bg www.peri.bg 46 Ukraine TOW PERI Ukraina 07400 Brovary peri@peri.ua www.peri.ua 47 Egypt Egypt Branch Ofce 11361 Heliopolis / Cairo info@peri.com.eg www.peri.com.eg 48 Serbia PERI Oplate d.o.o. 11272 Dobanovci ofce@peri.rs www.peri.rs
49 Mexico PERI Cimbras y Andamios, S.A. de C.V. Estado de Mxico, info@peri.com.mx www.peri.com.mx 50 Azerbaijan PERI Kalp ve skeleleri Baku peribaku@peri.com.tr www.peri.com.tr 51 Turkmenistan PERI Kalp ve skeleleri Agabat ahmet.kadioglu@peri.com.tr www.peri.com.tr 52 Belorussia PERI Belarus 220030 Minsk info@peri.by www.peri.com 53 Croatia PERI oplate i skele d.o.o. 10 250 Donji Stupnik/ Zagreb info@peri.com.hr www.peri.com.hr 54 Iran PERI GmbH Iran Branch Ofce Tehran info@peri.ir www.peri.ir
55 India PERI (India) Pvt Ltd Mumbai 400064 info@peri.in www.peri.in 56 Jordan PERI GmbH - Jordan 11947 Amman jordan@peri.com www.peri.com 57 Kuwait PERI Kuwait 13011 Kuwait kuwait@peri.com www.peri.com 58 Saudi Arabia PERI Engineering Division of Jamjoom Consult Saudi Arabia 21463 Jeddah info@peri.com.sa www.peri.com.sa 59 Qatar PERI Qatar LLC P .O.Box: 31295 - Doha info@periqatar.com www.periqatar.com 60 Algeria Socit PERI S.A.S. Kouba - Alger peri.alger@peri.fr www.peri.fr 61 Albania PERI Sh.p.k. Tirane erti.hasanaj@peri.com.tr www.peri.com.tr
62 Peru PERI Peruana SAC Chorrillos, Lima contacto@peri.com.pe www.peri.com.pe 63 Panama PERI Panama Inc. 0832-00155 Panama City info@peri.com.pa www.peri.com.pa 64 Angola PERIcofragens, Lda. Luanda renato.portugal@peri.pt www.peri.pt 65 Nigeria Heights Access Nigeria Ltd. Victoria Island, Lagos info@heightsaccessng.com www. heightsaccessng.com 66 Oman PERI (L.L.C.) Muscat perimct@perime.com www.perime.com
49
Wall Formwork Panel Formwork Girder Formwork Circular Formwork Facade Formwork Brace Frame
Climbing Systems Climbing Scaffold Self-Climbing System Climbing Protection Panel Platform Systems
Scaffold, Stairways, Working Platforms Facade Scaffold Working Platform Weather Protection Roof Stairway Access
Slab Formwork Panel Formwork Beam Grid Formwork Girder Formwork Slab Table Beam Formwork
Bridge and Tunnel Formwork Cantilevered Parapet Carriage Cantilevered Parapet Platform Engineers Construction Kit
Additional Systems Safety Systems Plywood Formwork Girders Stopend Systems Pallets Transportation Containers
PERI GmbH Formwork Scaffolding Engineering P .O. Box 1264 89259 Weissenhorn Germany Tel. +49 (0)7309.950-0 Fax +49 (0)7309.951-0 info@peri.com www.peri.com
Shoring Systems Steel Slab Props Aluminium Slab Props Tower Systems Heavy-Duty Props
Services Formwork Assembly Cleaning / Repairs Formwork Planning Software Statics Special Constructions