Beruflich Dokumente
Kultur Dokumente
B
2004 NIKON CORPORATION C
All rights reserved
Repair Manual
NIKON CORPORATION
Volume-1
Microscope
ECLIPSE 50i
ECLIPSE 55i
R-4758.B
2
REV. RECORD R-4758 REV. NUMBER:1
PAGE REV.MARK REV. DATE PAGE REV.MARK REV. DATE PAGE REV.MARK REV. DATE
1 B 2005.3.2 46 B 2005.3.2 91 B 2005.3.2
2 47 B 2005.3.2 92 B 2005.3.2
3 B 2005.3.2 48 B 2005.3.2 93 B 2005.3.2
4 B 2005.3.2 49 B 2005.3.2 94 B 2005.3.2
5 B 2005.3.2 50 B 2005.3.2 95 B 2005.3.2
6 B 2005.3.2 51 B 2005.3.2 96 B 2005.3.2
7 B 2005.3.2 52 B 2005.3.2 97 B 2005.3.2
8 B 2005.3.2 53 B 2005.3.2 98 B 2005.3.2
9 B 2005.3.2 54 B 2005.3.2 99 B 2005.3.2
10 B 2005.3.2 55 B 2005.3.2 100 B 2005.3.2
11 B 2005.3.2 56 B 2005.3.2 101 B 2005.3.2
12 B 2005.3.2 57 B 2005.3.2 102 B 2005.3.2
13 B 2005.3.2 58 B 2005.3.2 103 B 2005.3.2
14 B 2005.3.2 59 B 2005.3.2 104 B 2005.3.2
15 B 2005.3.2 60 B 2005.3.2 105 B 2005.3.2
16 B 2005.3.2 61 B 2005.3.2 106 B 2005.3.2
17 B 2005.3.2 62 B 2005.3.2 107 B 2005.3.2
18 B 2005.3.2 63 B 2005.3.2 108 B 2005.3.2
19 B 2005.3.2 64 B 2005.3.2 109 B 2005.3.2
20 B 2005.3.2 65 B 2005.3.2 110 B 2005.3.2
21 B 2005.3.2 66 B 2005.3.2 111 B 2005.3.2
22 B 2005.3.2 67 B 2005.3.2 112 B 2005.3.2
23 B 2005.3.2 68 B 2005.3.2 113 B 2005.3.2
24 B 2005.3.2 69 B 2005.3.2 114 B 2005.3.2
25 B 2005.3.2 70 B 2005.3.2 115 B 2005.3.2
26 B 2005.3.2 71 B 2005.3.2 116 B 2005.3.2
27 B 2005.3.2 72 B 2005.3.2 117 B 2005.3.2
28 B 2005.3.2 73 B 2005.3.2 118 B 2005.3.2
29 B 2005.3.2 74 B 2005.3.2 119 B 2005.3.2
30 B 2005.3.2 75 B 2005.3.2 120 B 2005.3.2
31 B 2005.3.2 76 B 2005.3.2 121 B 2005.3.2
32 B 2005.3.2 77 B 2005.3.2 122 B 2005.3.2
33 B 2005.3.2 78 B 2005.3.2 123 B 2005.3.2
34 B 2005.3.2 79 B 2005.3.2 124 B 2005.3.2
35 B 2005.3.2 80 B 2005.3.2 125 B 2005.3.2
36 B 2005.3.2 81 B 2005.3.2 126 B 2005.3.2
37 B 2005.3.2 82 B 2005.3.2 127 A
38 B 2005.3.2 83 B 2005.3.2 128 A
39 B 2005.3.2 84 B 2005.3.2 129 A
40 B 2005.3.2 85 B 2005.3.2 130 A
41 B 2005.3.2 86 B 2005.3.2 131 A
42 B 2005.3.2 87 B 2005.3.2 132 A
43 B 2005.3.2 88 B 2005.3.2 133 A
44 B 2005.3.2 89 B 2005.3.2 134 A
45 B 2005.3.2 90 B 2005.3.2 135 A
R-4758.B
3
Foreword ..................................................................................................................... P.5
Notes for Repair .......................................................................................................... P.5
Safety Precautions ...................................................................................................... P.5
1. Tools ........................................................................................................................... P.6
1-1. Tools for General Use and Preparations ............................................................... P.6
1-2. Tools for Special Purposes ................................................................................... P.7
1-3. Preparations ......................................................................................................... P.8
2. Specifications................................................................................................................ P.9
2-1. 50i ......................................................................................................................... P.9
2-2. 55i ....................................................................................................................... P.13
3. Optical Systems ........................................................................................................ P.20
3-1 50i ....................................................................................................................... P.20
3-2. 55i ....................................................................................................................... P.21
4. Connection Diagrams ............................................................................................... P.22
4-1. 50i ....................................................................................................................... P.22
4-2. 55i ....................................................................................................................... P.23
5. Disassembling/Assembling/Adjusting ....................................................................... P.24
5-1. Disassembling/Assembling/Adjusting Flow ......................................................... P.24
5-2. Removing Main Unit ........................................................................................... P.26
5-3. Disassembling/Assembling Elevation Block (For 50i/55i) ................................... P.27
5-3-1 Disassembling ................................................................................................ P.27
5-3-2. Assembling .................................................................................................... P.33
5-4. Disassembling/Assembling Condenser Holder Block (For 50i/55i) ..................... P.42
5-4-1. Disassembling ................................................................................................ P.42
5-4-2. Assembling .................................................................................................... P.46
5-5. Disassembling/Assembling Fine/Coarse Focus Block (For 50i/55i) .................... P.52
5-5-1. Disassembling ................................................................................................ P.52
5-5-2. Assembling .................................................................................................... P.59
5-6. Disassembling/Assembling Field Stop Block (For 50i/55i) .................................. P.68
5-6-1. Disassembling ................................................................................................ P.68
5-6-2. Assembling .................................................................................................... P.71
5-7. Disassembling/Assembling ND Filter Block (For 50i) .......................................... P.75
5-7-1. Disassembling ................................................................................................ P.75
5-7-2. Assembling .................................................................................................... P.77
Table of Contents
R-4758.B
4
5-8. Disassembling/Assembling Lighting Block (For 50i) ........................................... P.79
5-8-1. Disassembling .............................................................................................. P.79
5-8-2. Assembling ................................................................................................... P.82
5-9. Disassembling/Assembling Power Supply Assembly (For 50i) ........................... P.85
5-9-1. Disassembling .............................................................................................. P.85
5-9-2. Assembling ................................................................................................... P.87
5-10. Disassembling/Assembling Brightness Control Board (For 50i) .......................... P.89
5-10-1. Disassembling .............................................................................................. P.89
5-10-2. Assembling ................................................................................................... P.91
5-11. Disassembling/Assembling Seesaw Switch (For 50i) ......................................... P.93
5-11-1. Disassembling .............................................................................................. P.93
5-11-2. Assembling ................................................................................................... P.94
5-12. Disassembling/Assembling Color Compensation Filter Unit (For 55i) ................. P.95
5-12-1. Disassembling .............................................................................................. P.95
5-12-2. Assembling ................................................................................................... P.97
5-13. Disassembling/Assembling Diffuser Unit (For 55i) .............................................. P.99
5-13-1. Disassembling .............................................................................................. P.99
5-13-2. Assembling ................................................................................................. P.100
5-14. Disassembling/Assembling Light Source Unit (For 55i) .................................... P.102
5-14-1. Disassembling ............................................................................................ P.102
5-14-2. Assembling ................................................................................................. P.104
5-15. Disassembling/Assembling Switch Board (For 55i) .......................................... P.106
5-15-1. Disassembling ............................................................................................ P.106
5-15-2. Assembling ................................................................................................. P.108
5-16. Disassembling/Assembling Seesaw Switch (For 55i) ........................................P.110
5-16-1. Disassembling .............................................................................................P.110
5-16-2. Assembling .................................................................................................. P.111
5-17. Stage Tilt Adjustment (For 50i/55i) .....................................................................P.112
5-18. Stage Centering Adjustment (For 50i/55i) ..........................................................P.115
5-19. Condenser Holder Tilt Adjustment (For 50i/55i) .................................................P.117
5-20. Condenser Holder Upper Limit Stopper Position Adjustment (For 50i/55i) ....... P.121
5-21. LED Position Adjustment (For 55i) .................................................................... P.122
Table of Contents
Foreword R-4758.B
5
1. This manual is for ECLIPSE 50i and ECLIPSE 55i.
Where an item is common for both ECLIPSE 50i and ECLIPSE 55i, (For 50i/55i) is included
in the title.
Where an item is exclusive to either ECLIPSE 50i or ECLIPSE 55i, (For 50i) or (For 55i) is
included in the title.
For the Stage and Ergonomic Binocular Tube, refer to the ECLIPSE 50i/ECLIPSE 55i
Repair Manual Volume-2.
2. This repair manual has been written to be used as the textbook for the repair training course.
This manual is organized so that trainees can understand the mechanical and optical
construction of the microscope by practicing repair procedures from the beginning to the end.
3. The table of contents of this manual includes every item that might require repair and can
efficiently be used as the guide for repair.
4. Unplug the power cable and wear work-gloves before starting work.
Take extra care to avoid injury from sharp edges or projections and electric shock by touching
live components.
Notes for Repair:
- Use an appropriate screwdriver for the screw head slot. (Especially take care of the (+) slot
head screw).
- The plastic parts must be cleaned with a neutral solvent.
If an organic solvent (ether, thinner, alcohol, etc.) is used, discoloring or deterioration of the
part might occur.
- When cleaning the glass parts, take care to remove dust using a blower, etc. and wipe the
parts with a lens tissue moistened with alcohol or alcohol-ether mixture.
Safety Precautions
WARNING (For ECLIPSE 50i)
The lamp and surrounding areas (including the lamp house) become very hot during and
immediately after a period of illumination.
- To avoid risk of burns, do not touch the lamp or surrounding areas during or
immediately after a period of illumination.
- Make sure the lamp and surrounding areas have cooled sufficiently before attempting
to the replace lamp.
- To avoid risk of fire, do not place fabric, paper or highly flammable volatile materials
such as gasoline, petroleum benzine, paint thinner or alcohol near the lamp house
while the lamp is lit or during a period of around thirty minutes after the lamp has been
turned off.
- To avoid risk of burns, wait at least thirty minutes after the lamp is turned off to give it
sufficient time to cool.
Foreword
1. Tools R-4758.B
6
Tool No Name Illustration Remarks
J21084 Hex-key set
Set (x6)
T91400 (+) Screwdriver set
Set (x4)
T91000 (-) Screwdriver set
Set (x6)
T91204 (+) Wood handle driver
Diameter 6 mm
T91102 (-) Wood handle screwdriver
Width 5.5 mm
T91305
(+) Screwdriver bit
(For JCIS screw M2, M2.6)
2.5mm
115mm
T91320 (+) Screwdriver bit holder
8mm
90mm
T92041 Tweezers AA
T92162 Compass spanner A
T92163 Compass spanner B
E719
Handlap
(Alcohol container)
1-1. Tools for General Use and Preparations
1. Tools R-4758.B
7
Tool No Name Illustration Remarks
J28005 1 reading collimator
Stage tilt adjustment
Condenser holder tilt
adjustment
J28003 Parallel mirror
Stage tilt adjustment
Condenser holder tilt
adjustment
J25298 Centering tool
Stage centering
adjustment
J25481 80i sub stage tool A
Stage centering
adjustment
J25299 Centering rod
Stage centering
adjustment
1-2. Tools for Special Purposes
1. Tools R-4758.B
8
Tool No Name Illustration Remarks
J25295 Standard straight tube
LED position
adjustment
J25172 Centering telescope
LED position
adjustment
J25260 Ph tool ring
LED position
adjustment
Spring scale
Torque adjustment
1-3. Preparations
Alcohol (or alcohol-ether mixture), Lens tissue, Blower, Gasoline (for cleaning),
Bamboo stick (for applying lubricant, adhesive), Brass (or tin) foil, Dial gauge
For Lubricant and Adhesive: Refer to Repair Parts Lists (50i: KR-7483.A, 55i: KR-7485.A,)
1-2. Tools for Special Purposes/Preparations
2. Specifications R-4758.B
9
I. Overviews
1. Model Number
MBA85010: ECLIPSE 50i, Using halogen lamp as light source L
MBA85020: ECLIPSE 50i, Using halogen lamp as light source R
II. Main Items
1. Mounting System
- For nosepiece: Square dovetail (compatible with E series)
Can be attached and removed using tool.
- For eyepiece tube: Round dovetail (compatible with E series)
Can be attached and removed using clamp screw.
- For intermediate attachments: Eyepiece tube mounting dovetail and main
body top surface (Using M4 screw (4 pcs.))
2. Main Body Top Arm and Stand Blocks
- Height from table top to eyepiece mounting surface: 330 mm
- Height from table top to stage top: 199 mm
- Max. width: 208 mm
- Foot: With vibration-proof damper (4 pcs.)
3. Elevation Block
- Focusing system/Stage up-down system: Using roller races
- Stage up-down stroke: Upward 2 mm/Downward 28 mm
- Sub stage and up-down movement guide: DC integrated type
- Stage mounting system: Round dovetail (not compatible with E series)
- Condenser lens mounting system: Round dovetail (compatible with E series)
- Condenser lens up-down stroke: 27 mm
- Condenser lens stroke upper limit position: Adjustable (using tool)
- Condenser lens centering: 3 mm diameter
2-1. 50i
2. Specifications R-4758.B
10
4. Coarse/Fine Focus Block
- Coarse focus handle: 13.8 mm per rotation (reduction gear ratio: 3)
- Fine focus handle: 0.1 mm per rotation (reduction gear ratio: approx. 413)
- Minimum reading: 1 micron
- Coarse motion handle torque: Adjustable
- Refocusing mechanism: With one-touch refocusing mechanism (with
operation lever)
When the sub stage is lowered to the lower limit position by pushing the lever
down, the sub stage is locked to this position.
When the sub stage is lowered 2 mm further from this position by pushing
the lever down, the lock mechanism is canceled. The sub stage is returned
to the former position.
The rotary damper controls the return of the sub stage at a constant speed.
5. Lighting Block
- Composed of collector lens, field lens (f = 89.7), field stop, and filter
- Filter: ND8 (Detachable)
- Lemon-skin filter (2 pcs.): Built-in (Not detachable)
- Diameter of field stop: 1 to 30 mm diameter (design value: 0.8 to 30.5 mm
diameter)
- Field stop control: Right-hand side of the microscope base
- Filter control: Right-hand side of the microscope base
- Additional filter (diameter: 45 mm, thickness: 3 mm): Up to two filters can be
attached tilting 5 degrees above the field lens.
6. Light Source Block
- Lamp ratings and type: 6V/30W halogen lamp, PHILIPS 5761
- Average lamp life: 100 hours (listed on product brochure)
- Lamp house detachable
2-1. 50i
2. Specifications R-4758.B
11
III. Configurations and Functions
1. System Diagram
(Described for eyepiece tube, intermediate attachments, nosepiece, stage,
Condenser lens, and polarizer)
2-1. 50i
J-FL 50i55i Epi-Fluorescence
Attachment (MBE84000)
C-TE Ergonomic Tube
(MBB76500)
Binocular Tube
(MBB72100/72105)
Trinocular Tube F
(MBB73100/73105)
Trinocular Tube T
(MBB73110)
C-TEP DSC Port
(MBB76600)
Double Port 0/100
(MBB74105)
Double Port 0/100
(MBB74105)
Drawing Tube
(MBB75400)
Teaching Unit S by S type B
(MBB75110)
Teaching Unit S by S type A
MBB75130
C-SR Right Handle
Stage (MBC71600)
C-SR Left Handle
Stage (MBC71610)
C-HC1 Specimen
Holder 1C (MBC75040)
C-HR2 Specimen
Holder 2R (MBC75010)
C-HL2 Specimen
Holder 2L (MBC75020)
Polarizer with First-order
Red Tint Plate
(MBB75380)
Simple Polarizer
(MBB75370)
J-CY Cytodiagnostic Unit
(MBP89000)
50i Halogen Lamp L
(MBA85010)
50i Halogen Lamp R
(MBA85020)
:Option
Objective Lens
(CFI60)
Intermediate Tube w/Simple
Analyzer (MBB75370)
Intermediate Tube
w/Analyzer (MBB75360)
Main Teaching Unit
MBB75120
Teaching Unit F to F
(MBB75100)
C-N Sextuple Nosepiece
(MBP71300)
Double Port
(MBB74100)
Magnification Module
(MBB75500)
Eyelevel Riser
(MBB75710)
Condenser (dry)
(MBL12000)
Condenser (oil)
(MBL12001)
A/A Condenser
(MBL71400)
Swing-out Condenser
(MBL11300)
Abbe Condenser
(MBL71100)
LWD Achromat
Condenser (MBL75000)
Achromat Swing-out
Condenser 1-100X
(MBL71300)
PH Turret Condenser
(MBL73100)
2. Specifications R-4758.B
12
2. Restrictions (Following products are not installable.)
- Condenser lens
D-CUD-E Automatic U condensor (dry) (MBL78500)
D-CUD U condensor (dry) (MBL78600)
- Intermediate attachments
D-FL U-EPI Fluorescence (MBE74100)
D-DH-E DIH E (MBD76100)
D-DH DIH M (MBD76200)
- Stage
C-SRR Right handle R stage (MBC71500)
C-SLR Left handle R stage (MBC71600)
D-S-E Automatic XY stage (MBC76100)
2-1. 50i
2. Specifications R-4758.B
13
I. Overviews
1. Model Number
MBA85040: ECLIPSE 55i, Using LED as light source L
MBA85050: ECLIPSE 55i, Using LED as light source R
II. Main Items
1. Mounting system
- For nosepiece: Square dovetail (compatible with E series)
Can be attached and removed using tool.
- For eyepiece tube: Round dovetail (compatible with E series)
Can be attached and removed using clamp screw.
- For intermediate attachments: Eyepiece tube mounting dovetail and main
body top surface (Using M4 screw (4 pcs.))
2. Main Body Top Arm and Stand Blocks
- Height from table top to eyepiece mounting surface: 330 mm
- Height from table top to stage top: 199 mm
- Max. width: 208 mm
- Foot: With vibration-proof damper (4 pcs.)
3. Elevation Block
- Focusing system/Stage up-down system: Using roller races
- Stage up-down stroke: Upward 2 mm/Downward 28 mm
- Sub stage and up-down movement guide: DC integrated type
- Stage mounting system: Round dovetail (not compatible with E series)
- Condenser lens mounting system: Round dovetail (compatible with E series)
- Condenser lens up-down stroke: 27 mm
- Condenser lens stroke upper limit position: Adjustable (using tool)
- Condenser lens centering: 3 mm diameter
2-2. 55i
2. Specifications R-4758.B
14
4. Coarse/Fine Focusing Block
- Coarse focus handle: 13.8 mm per rotation (reduction gear ratio: 3)
- Fine focus handle: 0.1 mm per rotation (reduction gear ratio: approx. 413)
- Minimum reading: 1 micron
- Coarse motion handle torque: Adjustable
- Refocusing function: Refocusing with a single touch of the lever (with
operation lever)
When the sub stage is lowered to the lower limit position by pushing the lever
down, the sub stage is locked to this position.
When the sub stage is lowered 2 mm further from this position by pushing
the lever down, the lock mechanism is canceled. The sub stage is returned
to the former position.
The rotary damper controls the return of the sub stage at a constant speed
5. Lighting Block
- Composed of collector lens, field lens (f = 89.7), field stop, and filter
- Filter: LA60 (Detachable)
- Lemon-skin filter (2 pcs.): Built-in (Not detachable)
- Diameter of field stop: 1 to 30 mm diameter (design value: 0.8 to 30.5 mm
diameter)
- Field stop control: Right-hand side of the microscope base
- Filter control: Right-hand side of microscope base
- Additional filter (diameter: 45 mm, thickness: 3 mm): Up to two filters can be
attached tilting 5 degrees above the field lens.
6. Light Source Block
- White LED array (7 LEDs are used.)
- Lamp house detachable
7. Electric System
- Brightness control dial: Rotary system, located on the right-hand side of the
microscope base.
- Preset switch: Push-button, located on the right-hand side of the microscope
base.
- Lithium-ion battery mounting port: Located on the back of the LED array board.
- Input connector: Located on the back.
- Power connector for Ergo-View cytodiagnostic unit: Located on the back.
- Signal connector for Ergo-View cytodiagnostic unit: Located on the back.
- Hand-switch connector for Ergo-View cytodiagnostic unit: Located on the back.
2-2. 55i
2. Specifications R-4758.B
15
7-1 Power Input
The microscope uses power from an AC adapter or from a battery, as follows.
When the power is supplied from an AC adapter, this has priority over any battery.
1. AC adapter input: Option
Input voltage: 12 V/1.5 ADC
Specified AC adapter: Manufacturer: ILAN ELECTRONICS LTD
Model: F1650K
- Rated input voltage: 100 to 240 VAC/1.2 A max. (when inputting 115
VAC), 47 to 63 Hz
2. Specified Lithium-ion rechargeable battery: Option
Manufacturer: Nikon: Code: EN-EL1
Rating: 7.4 V/720 mAh
Specified battery charger: MH-53 or similar
Note: UR-421 (SANYO Electric Co., Ltd) can be used as the equivalent
battery charger.
7-2 Power Output (For Ergo-View cytodiagnostic unit)
Supply power to Ergo-View cytodiagnostic unit.
- DC 12 V/1 A max.: Current limitation (approx. 1A within 1 sec)
- DC 12V/0.5 A max.: Continuous supply
7-3 Battery Run Time
1. When Ergo-View cytodiagnostic unit is not used
4.5 hours minimum: When observed continuously at an LED light source at
maximum light intensity using a new rated-capacity battery
10 hours minimum: When observed continuously at 40% of the maximum current
The following are assumed for this case:
- Maximum illuminance using the Ergo-View cytodiagnostic unit with
PlanApo40x and a CB filter attached
- 4 lx (eyepiece illuminator reading)
2. When Ergo-View cytodiagnostic unit is used (Reference value)
Approx. 3.5 hours: Run time at maximum light intensity assuming that the
magnification of the Ergo-View cytodiagnostic unit is changed 5 times a
minute
7-4. Battery Charge Time (Reference value)
Approx. 100 minutes: When a specified battery charger is used
7-5. LOW-Battery Detection
LOW-Battery is displayed when the battery voltage lowers to 7.13 +/-0.2 V
during operation. The Power LED blinks at a cycle of approx. 5 Hz.
2-2. 55i
2. Specifications R-4758.B
16
7-6. Battery Shutdown Detection
When the battery voltage reaches 5.75 +/-0.16 V during operation, the
microscope shuts down to prevent the lithium battery from over discharging.
It takes 3 to 30 minutes (reference value) from LOW-Battery detection for
the microscope to shutdown.
The time depends mainly on the number of charge/discharge repetition times,
ambient temperature, and LED luminance setting.
To reboot the microscope, replace the battery with a charged new battery or
switch the power source to the AC adapter.
7-6-1. Replacing Battery
Remove the lamp house cover and replace the battery in the battery
pocket with a new one.
7-7. White LEDs
Seven white LEDs NSPW510BS (Nichia Corporation) are used
(luminous intensity rank = S or R, color tone rank = b1 or b2, maximum
drive current = 22 mA/LED).
7-8. LED Current Variation Range
Approx. 0.05 to 22 mA per LED
Current variation dynamic range: Approx. 440 times
Total current of seven LEDs is controlled at a constant value.
Current variation at maximum light intensity: 5% (reference value)
7-9. Brightness Control
The LEDs light intensity is adjusted with the master brightness control
knob on the operation panel.
The current variation characteristics (B characteristics) vary with the
master brightness control knob characteristics (A characteristics).
When the alternate preset switch is pressed, the light intensity adjustment
is switched to the preset brightness control which can be adjusted using a
(-) screwdriver through the adjustment hole of the operation panel.
The preset brightness control knob is visually set to the neutral position
(half of maximum light intensity) at the factory prior to shipping.
2-2. 55i
2. Specifications R-4758.B
17
7-10. LED Current Control by Varying Magnification of Ergo-View Cytodiagnostic Unit
When the magnification of the Ergo-View cytodiagnostic unit is set to a
high value, the LED current increases to approx. 3.2 times, which makes
the LED brighter. However, the magnification is limited to the maximum
LED current 22 mA.
The LED current does not depend on the magnification of the Ergo-View
cytodiagnostic unit while the preset switch is ON.
7-11. Life of White LED (Reference data)
According to the reference data provided by the manufacturer, the relation
between LED operating time and light intensity is as shown below. The life
of white LEDs is calculated assuming that the light intensity at the
beginning of test = 100% and operating time = 8 hours/day, 250 days/year
Ambient
temperature
Operating
current
Operating
time
Light
intensity
Life of LED
Ta = 25 C IF = 20 mA 3500 hours 70% 1.75 years
Ta = 25 C IF = 20 mA 8000 hours 55% 4 years
Ta = 25 C IF = 10 mA 8000 hours 90% 4 years
7-12. Input/Output Connectors
- Input connector for cytodiagnostic unit switch: 3.5 diameter mini-jack
Connect the cable of the cytodiagnostic unit hand switch.
- Input/output connector for cytodiagnostic unit signal: 3.5 diameter mini-jack
Connect the signal cable of the cytodiagnostic unit.
Input/output the hand switch signal and magnification signal.
- Power output connector for cytodiagnostic unit: DC jack
Connect the cytodiagnostic unit power supply cable.
Note: The shape of this connector differs from the power input
connector.
- Power input connector: DC jack
Connect the power output plug of AC adapter.
7-13. Indicators
- Power ON/OFF indicator LED (Green): Located on the right side
operation panel of the microscope base
- Lamp house high temperature caution label
- Rated current indication seal
2-2. 55i
2. Specifications R-4758.B
18
III. Configurations and Functions
1. System Diagram
(Described for eyepiece tube, intermediate attachments, nosepiece, stage,
Condenser lens, and polarizer)
2-2. 55i
J-FL 50i55i
Epi-Fluorescence
C-TE Ergonomic Tube
(MBB76500)
Binocular Tube
(MBB72100/72105)
Trinocular Tube F
(MBB73100/73105)
Trinocular Tube T
(MBB73110)
C-TEP DSC Port
(MBB76600)
Double Port
(MBB74100)
Double Port 0/100
(MBB74105)
Magnification
Module
Double Port 0/100
(MBB74105)
Drawing Tube
(MBB75400)
Teaching Unit F to F
(MBB75100)
Teaching Unit S by S type B
(MBB75110)
Main Teaching Unit
MBB75120
Teaching Unit S by S type A
MBB75130
C-N Sextuple
Nosepiece
C-SR Right Handle
Stage (MBC71600)
C-SR Left Handle
Stage (MBC71610)
C-HC1 Specimen
Holder 1C (MBC75040)
C-HR2 Specimen
Holder 2R (MBC75010)
C-HL2 Specimen
Holder 2L (MBC75020)
C-ER Eyelevel Riser
(MBB75710)
A/A Condenser
(MBL71400)
Swing-out Condenser
(MBL11300)
A/A Condenser
(MBL71400)
LWD Achromat
Condenser
Achromat Swing-out
Condenser 1-100X
(MBL71300)
J-CY Cytodiagnostic
Unit (MBP89000)
55i LED L
MBA85040
55iLED R
(MBA85050)
:Option
Objective Lens
(CFI60)
2. Specifications R-4758.B
19
2. Restrictions (Following products are not installable.)
- Condenser lens
D-CUD-E Automatic U condenser (dry) (MBL78500)
D-CUD U condensor (dry) (MBL78600)
DF condenser (dry) (MBL12000)
DF condenser (oil) (MBL12001)
PH condenser (MBL73100)
- Intermediate attachments
D-FL U-EPI Fluorescence (MBE74100)
D-DH-E DIH E (MBD76100)
D-DH DIH M (MBD76200)
C-ISA simple analyzer (MBB75350)
C-IA Analyzer (MBB75360)
- Stage
C-SRR Right handle R stage (MBC71500)
C-SLR Left handle R stage (MBC71600)
D-S-E Automatic XY stage (MBC76100)
- Others
Simple polarizer (MBB75310)
Polarizer with first-order red tint plate (MDW10200)
2-2. 55i
3. Optical Systems R-4758.B
20
The following optical system is based on the ECLIPSE 50i.
The cemented lens surfaces are omitted from the drawing because the lens direction only
is of concern here.
3-1. 50i
6V 30W
Diffuser ND8
Field stop
3. Optical Systems R-4758.B
21
The following optical system is based on the ECLIPSE 55i.
The cemented lens surfaces are omitted from the drawing because the lens direction only
is of concern here.
3-2. 55i
LED arrays
Lemon skin
Mat surface Evaporated surface
Color compensation filter
Field stop
Evaporated
surface
Mirror
4. Connection Diagrams R-4758.B
22
4-1. 50i
4. Connection Diagrams R-4758.B
23
4-2. 55i
5. Disassembling/Assembling/Adjusting R-4758.B
24
5-1. Disassembling/Assembling/Adjusting Flow
< ECLIPSE 50i >
26
29
85
29
29
30
34
38
38
113
116
118
122
39
40
40
73
72
72
69
68 70
74
74
79
80
80
81
81
93
86
85
42
47
75
52
67
89
68
89
Removing Stage/Eyepiece tube/Nosepiece/Condenser lens
Elevation Block
Removing fine/coarse focus block
Removing power supply assembly
Removing elevation block
Removing condenser holder
Disassembling/Assembling
elevation block
Roller race movement adjustment
Installing condenser holder
Installing elevation block
Stage tilt adjustment
Stage centering adjustment
Condenser holder tilt adjustment
Condenser holder upper
limit stopper position adjustment
Installing fine/coarse focus block
Elevation block movement check
using fine/coarse focus handle
Re-focusing mechanism
operation check
Disassembling/Assembling
fine/coarse focus block
Fine/coarse focus block
Fine torque adjustment
Condenser holder block
Disassembling/Assembling
condenser holder
Knob/rack engaging adjustment
Brightness control board
Removing brightness control dial
Removing field stop block
Disassembling/Assembling
brightness control board
ND filter block
Disassembling/Assembling
ND filter block
Power supply assembly
Removing lamp
Disassembling/Assembling
power supply assembly
Seesaw switch
Disassembling/Assembling
seesaw switch
Lighting block
Removing lamp
Removing lighting block
Disassembling/Assembling
diffuser
Disassembling/Assembling
collector lens
Disassembling/Assembling
cable with lamp socket
Field stop block
Removing field stop block
Disassembling/Assembling blade
Blade mount position adjustment
Installing field stop block
Diaphragm open-shut dial
operation check
Disassembling mirror/lens
Cleaning adhesive coating surface
of mirror/lens
Cementing mirror/lens
NOTE: The number at upper right of the frame shows the page of this item.
5. Disassembling/Assembling/Adjusting R-4758.B
25
5-1. Disassembling/Assembling/Adjusting Flow
< ECLIPSE 55i >
26
29
103
29
29
30
34
38
38
113
116
118
122
39
40
40
52
67
42
47
103
104
105
123
68
69
72
72
73
70
74
74
99
100
101
101
111
107
68
107
95
96
Removing Stage/Eyepiece tube/Nosepiece/Condenser lens
Elevation Block
Removing fine/coarse focus block
Removing control board
Removing elevation block
Removing condenser holder
Disassembling/Assembling
elevation block
Roller race movement adjustment
Installing condenser holder
Installing elevation block
Stage tilt adjustment
Stage centering adjustment
Condenser holder tilt adjustment
Condenser holder upper
limit stopper position adjustment
Installing fine/coarse focus block
Elevation block movement check
using fine/coarse focus handle
Re-focusing mechanism
operation check
Fine/coarse focus block
Disassembling/Assembling
fine/coarse focus block
Fine torque adjustment
Condenser holder block
Disassembling/Assembling
condenser holder
Knob/rack engaging adjustment
Light source Unit
Removing control board
Disassembling/Assembling
LED board
Installing control board
LED position adjustment
Field stop block
Removing field stop block
Disassembling/Assembling blade
Blade mount position adjustment
Installing field stop block
Diaphragm open-shut dial
operation check
Disassembling mirror/lens
Cleaning adhesive coating surface
of mirror/lens
Cementing mirror/lens
Diffuser unit
Removing diffuser unit
Disassembling lens/diffuser
Cleaning adhesive coating surface
of mirror/diffuser
Installing diffuser unit
Seesaw switch
Disassembling/Assembling
seesaw switch
Color compensation filter unit
Removing color compensation
filter unit
Disassembling/Assembling
color filter unit
Switch board
Removing brightness control dial
Removing field stop block
Disassembling/Assembling
switch board
NOTE: The number at upper right of the frame shows the page of this item.
5. Disassembling/Assembling/Adjusting R-4758.B
26
Before disassembling and assembling the inside mechanisms of the microscope,
remove the main unit. This will make it easier to disassemble and assemble the internal
parts, and re-adjust the optical system.
1. Eyepiece tube 2. Nosepiece
3. Stage 4. Condenser lens
Loosen the eyepiece clamp screw beneath
the eyepiece tube, and remove the
eyepiece tube.
Loosen the clamp screw on the side of the
nosepiece, and remove the nosepiece.
Loosen the set screw on the front side of
the stage using a hex-key, and remove the
stage.
Loosen the set screw on the condenser
receptacle using a hex-key, and remove the
condenser lens.
5-2. Removing Main Unit
Clamp screw Eyepiece tube Clamp screw
Nosepiece
Stage
Set screw
Set screw
Condenser lens
5. Disassembling/Assembling/Adjusting R-4758.B
27
- Disassembling the elevation block is not usually necessary, but if liquid (water etc.)
has dropped into the microscope, it should be disassembled.
- The two roller races (#A3) fixed to the attaching plate must not to be disassembled at
the same time. When reassembling one roller race, the other (assembled) roller race
is used as a reference for adjustment.
- Some screws are fixed with adhesive. Apply alcohol to melt the adhesive on these
screws.
WARNING (For ECLIPSE 50i)
- When disassembling the elevation block, remove the lamp cover from the lamp
house.
The lamp and surrounding areas (including the lamp house) become very hot
during and immediately after a period of illumination.
To avoid risk of burns, do not touch the lamp or surrounding areas during or
immediately after a period of illumination.
- To avoid risk of fire, do not place fabric, paper or highly flammable volatile
materials such as gasoline, petroleum benzine, paint thinner or alcohol near the
lamp house while the lamp is lit or during a period of around thirty minutes after
the lamp has been turned off.
- To avoid risk of burns, wait at least thirty minutes after the lamp is turned off to
give it sufficient time to cool.
5-3-1. Disassembling
1. Remove the eyepiece tube. (Refer to Section 5-2.)
2. Remove the objective lens.
3. Remove the condenser lens. (Refer to Section 5-2.)
4. Remove the nosepiece. (Refer to Section 5-2.)
5. Remove the stage. (Refer to Section 5-2.)
6. While pressing the two portions of the lamp
cover (#223) in the arrow directions (a)
shown in the photograph, move it in the
arrow direction (b) to remove.
5-3-1. Disassembling Elevation Block (For 50i/55i)
Lamp cover
(#223)
(a)
(a)
(b)
5. Disassembling/Assembling/Adjusting R-4758.B
28
7. In the case of 50i, disconnect the lamp
(#227) to prevent damage.
8. Pull out the hexagonal driver (#248).
9. Remove the four hexagon socket head cap
bolts (M3 x 6) (#254), and remove the
plastic cover (#202).
10. Remove the cap (#233).
11. In the case of 50i, remove the power
supply assembly. (Refer to Section 5-9.)
In the case of 55i, remove the control board
of the light source unit. (Refer to Section
5-14.)
12. Place the microscope upside down.
13. Remove the five special hexagon bolts
(M3 x 6) (#239), and remove the
bottom cover.
14. Remove the two hexagon socket head cap bolts (M3 x 10) (#51), and remove the
plastic cover (#411).
15. Insert a (-) 2 mm screwdriver into the spaces on both sides of the plastic cover
shown in the photograph to release the lock of the claws.
[NOTE]
When releasing the lock, take care not to break the claws.
5-3-1. Disassembling Elevation Block (For 50i/55i)
Hexagonal driver (#248)
Cap (#233) Plastic cover (#202)
Lamp (#227)
Hexagon
socket head
cap bolts
(M3 x 6)(#254)
Hexagon socket head cap bolts (M3 x 10) (#51)
(-) screwdriver Claws of plastic cover
Bottom cover
Special hexagon bolts
(M3 x 6) (#239)
Special
hexagon bolt
(M3 x 6) (#239)
Fine/coarse
focus block
Plastic cover (#411)
5. Disassembling/Assembling/Adjusting R-4758.B
29
16. Hold the fine/coarse focus block firmly by
hand, and remove the two hexagon socket
head cap bolts (M3 x 12) (#52).
Remove the fine/coarse focus block and
the plastic cover from the microscope
base.
17. While holding the elevation block by hand,
place the microscope to its original position.
[NOTE]
Since the fine/coarse focus block is
removed, the movement of the elevation
block is not fixed.
Therefore, when the microscope is placed
to its original position, be sure to keep hold
of the elevation block.
18. While holding the elevation block firmly by
hand so that it does not drop, remove the six
hexagon socket head cap bolts (M4 x 16)
(#53) to remove the elevation block.
19. Remove the three hexagon socket head
cap bolts (M3 x 8) (#442), and remove the
condenser holder block.
5-3-1. Disassembling Elevation Block (For 50i/55i)
Hexagon socket
head cap bolts
(M3 x 12) (#52)
Fine/coarse focus block
Elevation block
Hexagon socket head
cap bolts (M4 x 16) (#53)
Hexagon socket head cap bolts (M4 x 16) (#53)
Hexagon socket head
cap bolts (M3 x 8) (#442) Condenser holder
5. Disassembling/Assembling/Adjusting R-4758.B
30
20. Remove the two hexagon socket head cap bolts (M3 x 6) (#441) on the front and
two hexagon socket head cap bolts (M3 x 8) (#442) on the rear. Remove the plastic
cover (#410).
21. Remove a hexagon socket head cap bolt
(M3 x 12) (#443) of the stroke limitation
screw.
22. Remove the two hexagon socket head cap
bolts (M3 x 6) (#441), and remove the
plate spring (#412) (with the rubber plate).
23. Remove the two hexagon socket head cap
bolts (M3 x 8) (#442), and remove the cap
(#415) and rotary damper (#414).
24. Tighten a set screw (#452) on the side of
the sub body.
25. Remove the two hexagon socket head cap
bolts (M3 x 6) (#441), and remove the
shaft supporter (#407).
5-3-1. Disassembling Elevation Block (For 50i/55i)
Hexagon socket head cap bolts (M3 x 8) (#442)
Plastic cover (#410)
Plastic cover (#410)
Hexagon socket
head cap bolts
(M3 x 6) (#441)
Hexagon socket head
cap bolt (M3 x 12) (#443)
(Stroke limitation screw)
Cap (#415), Rotary
damper (#414)
Hexagon socket head
cap bolts (M3 x 8)(#442)
Plate spring (#412)
Hexagon socket head
cap bolts (M3 x 6) (#441)
Hexagon socket head cap bolts (M3 x 6) (#441)
Shaft supporter
(#407)
Set screw (#452)
5. Disassembling/Assembling/Adjusting R-4758.B
31
26. While holding the top surface of the rack
(#406) by finger, loosen the set screw
tightened in step 24.
[NOTE]
When the set screw is loosened, the rack
will pop out by the power of the two coil
springs.
Be sure to hold the top surface of the rack
to prevent injury or damage to the
surroundings when the rack pops out.
27. Remove the rack, coil spring (#405), coil
spring (#404) and spring guide (#403).
28. Remove the two plate washers from the
hole of the sub body.
[NOTE]
The two plate washers are only installed
on some microscope. If they are not
installed, go to step 29.
Set screw (#452) Rack (#406)
Rack (#406)
Coil spring
(#404)
Coil spring
(#405)
Spring guide
(#403)
Sub body
Plate washers (2 pcs)
Sub body
5-3-1. Disassembling Elevation Block (For 50i/55i)
5. Disassembling/Assembling/Adjusting R-4758.B
32
29. Place the elevation block right-hand side
down, and fully loosen the four set screws
(#447).
30. Remove the four hexagon socket head
cap bolts (M3 x 16) (#418), and remove
the roller race (#A3) on the left side of the
elevation block. Remove the sub body
from the elevation Block.
[NOTE]
When removing the roller race, the
cylindrical rollers (12 pcs each on up and
lower sides) might fall. Be careful not to
lose them.
The guide rails (#417) and separators
(#408) are also removed at the same time.
31. If there is a rusty or worn section on the
cylindrical rollers, separator and/or guide
rails (#417), replace it with a new one.
32. If there is a rusty section on the mounting
surface of the roller races and attaching
plate (#402), scrape it using a scraper.
The disassembly of the elevation block is completed.
The disassembled parts should be washed and cleaned.
5-3-1. Disassembling Elevation Block (For 50i/55i)
Sub body
Elevation block
Set screws (#447)
Roller race (#A3)
Hexagon socket head cap
bolts (M3 x 16) (#418)
Roller race (#A3) Mounting surface
Attaching plate
(#402)
Roller race (#A3)
5. Disassembling/Assembling/Adjusting R-4758.B
33
5-3-2. Assembling
1. Paste the two guide rails to the two roller
races using lubricant L4010 as a substitute
for adhesive.
2. Paste the guide rails to the races on both
sides of the sub body using lubricant
L4010 in the same way as step 1.
3. Apply lubricant L4010 to the roller race on
the attaching plate assembled in step 1,
and place the separator and twelve
cylindrical rollers on the roller race.
4. Apply lubricant L4010 to the roller race on the sub body, and place the separator and
twelve cylindrical rollers on the race.
5. Assemble the sub body to the roller race on the attaching plate, and lightly tighten the
roller race with the four hexagon socket head cap bolts (M3 x 16) while pressing it to
the sub body.
5-3-2. Assembling Elevation Block (For 50i/55i)
Attaching plate
(#402)
Guide rails (#417)
Sub body
Roller race (#A3) Roller race (#A3)
Roller race (#A3)
Cylindrical rollers
(12 pcs) (#409)
Attaching plate (#402)
Separator (#408)
Sub body
Cylindrical rollers
(12 pcs) (#409)
Separator
(#408)
Sub body
Hexagon socket head
cap bolts (M3 x 16) (#418)
Attaching
plate (#402)
Roller race (#A3)
Sub body
5. Disassembling/Assembling/Adjusting R-4758.B
34
6. Move the sub body fully right and left, and adjust the position of the separator so that
the edges of the separator and the roller race coincide.
Also adjust the position of the separator on the opposite side in the same way.
7. Move the sub body so that the set screw
on the attaching plate is adjacent to the
cylindrical roller.
8. Tighten the set screw close to the
cylindrical roller with the following
tightening torque using torque driver.
Tightening torque: 1 kg x cm
9. Repeat steps 7 and 8, and tighten the
remaining three set screws in the same
way.
10. Tighten the four hexagon socket head cap
bolts to fix the roller race.
11. Move the sub body, and check the
following:
- The cylindrical roller and separator are
still in position.
- The sub body moves smoothly and
lightly without slack.
Push the sub body and check, using a
spring scale, that 50 to 100g pressure is
required to effect movement. If not to meet
the specification, repeat steps 7 to 10.
[NOTE]
When the four hexagon socket head cap bolts securing the roller race are firmly
tightened, the sub body sometimes loses its movement.
In this case, perform steps
7 to 10 again.
5-3-2. Assembling Elevation Block (For 50i/55i)
Sub body
Edges of the separator and
the roller race are coincided.
Roller race (#A3)
Hexagon socket head
cap bolts (M3 x 16)(#418)
Roller race (#A3)
Set screws (#447)
Sub body
Spring scale
Sub body
Edges of the separator and
the roller race are coincided.
Roller race (#A3)
5. Disassembling/Assembling/Adjusting R-4758.B
35
12. Apply adhesive #757 to the threads of the
four set screws tightened in steps 8 and 9.
13. After inserting the two plate washers into
the 13 mm diameter hole of the sub body,
apply lubricant L4010 to the inner surface
of the hole.
[NOTE]
The two plate washers are only installed
on some microscope. If the plate washers
were present during disassembling, be
sure to insert them in this step.
14. Put the spring guide into the hole of the sub body, and insert its tip into the center
hole on the spring retainer (#432).
[NOTE]
Be sure to insert the spring guide tip into the spring retainer hole.
15. Apply a light coating of lubricant L3047 to the whole surfaces of the two kinds of coil
springs.
16. Fit
the lubricated coil springs into the hole of the sub body.
17. Install the rack to the sub body while
fitting the two coil springs into the hole of
the rack.
[NOTE]
Be sure to install the rack in the direction
as shown in the photograph.
5-3-2. Assembling Elevation Block (For 50i/55i)
Plate washers
(2 pcs)
Sub body
Apply lubricant
Sub body
Spring retainer (#432)
Tip of the
spring guide
Sub body
Spring guide (#403)
Coil spring (#405)
Coil spring (#404)
Sub body
Rack (#406)
Two coil springs
and spring guide
5. Disassembling/Assembling/Adjusting R-4758.B
36
18. After pushing the rack into the hole so that
the edges of the rack and the sub body
coincide, lightly tighten a set screw.
19. Install the shaft supporter to the sub body while inserting the spring guide tip into the
center hole of the shaft supporter, and tighten it using the two hexagon socket head
cap bolts (M3 x 6).
[NOTE]
After tightening the bolts, check again that the spring guide tip is inserted into the
spring retainer hole on the opposite side.
(5013_1)
20. Loosen the set screw lightly tightened in
step 18.
[NOTE]
When the set screw is firmly tightened, the
refocusing function cannot operate.
5-3-2. Assembling Elevation Block (For 50i/55i)
Set screw (#452)
Rack (#406)
Shaft supporter
(#407)
Hexagon socket head
cap bolts (M3 x 6) (#441)
Tip of the
spring guide
Spring retainer
(#432)
Tip of the
spring guide
Sub body
Loosen this set screw.
Shaft supporter
(#407)
Hexagon socket head
cap bolts (M3 x 6) (#441)
Tip of the
spring guide
5. Disassembling/Assembling/Adjusting R-4758.B
37
21. Tighten the hexagon socket head cap bolt (M3 x 12) of the stroke limitation screw.
22. Tighten the plate spring (with rubber plate) using the two hexagon socket head cap
bolts (M3 x 6).
When tightening, adjust the position of the plate spring so that the edge of the plate
spring is parallel to the edge of the boss on the attaching plate.
23. Tighten the cap and rotary damper using the two hexagon socket head cap bolts
(M3 x 8).
24. Tighten the plastic cover using the two hexagon socket head cap bolts (M3 x 6) on
the front and two hexagon socket head cap bolts (M3 x 8) on the rear.
5-3-2. Assembling Elevation Block (For 50i/55i)
Plate spring (#412)
Make parallel the edges of the plate spring
with the boss on the attaching plate.
Hexagon socket
head cap bolts
(M3 x 6) (#441)
Attaching plate (#402)
Hexagon socket head cap bolts (M3 x 8) (#442)
Plastic cover (#410) Plastic cover (#410)
Hexagon socket
head cap bolts
(M3 x 6) (#441)
Hexagon socket
head cap bolts
(M3 x 6) (#441)
Plate spring (#412)
Hexagon socket
head cap bolts
(M3 x 8) (#442)
Hexagon socket head cap
bolt (M3 x 12) (#443)
(Stroke limitation screw)
Cap (#415) and
Rotary damper
(#414)
5. Disassembling/Assembling/Adjusting R-4758.B
38
25. Install the condenser holder block, and
firmly move it in the direction of the arrow.
Tighten it with three hexagon socket head
cap bolts (M3 x 8).
[NOTE]
Be sure to tighten the condenser block
while moving it in the direction of the arrow.
26. While holding the elevation block so that it does not drop, tighten it using the six
hexagon socket head cap bolts (M4 x 16).
[NOTE]
Be sure to tighten the bolts while pushing the elevation block in the direction of the
arrows.
27. While holding the elevation block, place the microscope upside down.
[NOTE]
Since the fine/coarse focus block is removed, the elevation block is not fixed.
Therefore, when placing the microscope to the original position, hold the elevation
block by hand.
28. Perform the following adjustments
:
- Stage tilt adjustment (Refer to Section 5-17.)
- Stage centering adjustment (Refer to Section 5-18.)
- Condenser holder tilt adjustment (Refer to Section 5-19.)
- Condenser holder upper limit stopper position adjustment (Refer to Section 5-20.)
5-3-2. Assembling Elevation Block (For 50i/55i)
Condenser holder block
Hexagon socket head
cap bolts (M3 x 8) (#442)
Elevation block
Hexagon socket head
cap bolts (M4 x 16) (#53)
Hexagon socket head cap bolts (M4 x 16) (#53) Elevation block
5. Disassembling/Assembling/Adjusting R-4758.B
39
29. Set the elevator and the coarse/fine focus
drive in the following assembly positions:
[Assembling positions]
With the main body turned upside down (photo):
Elevator: Lowest position
Coarse/fine focus drive: Where the limit
screw of the gear contacts the lower limit,
as shown in the photograph on the right.
(This applies to both right-handle and
left-handle designs.)
After these adjustments are completed,
place the plastic cover under the fine/coarse focus block, and hold these parts by hand firmly.
While engaging the gear of the fine/coarse focus block with the rack of the elevation
block, insert the two pins on the microscope into the two standard holes on the
fine/coarse focus block. Tighten the fine/coarse focus block using the two hexagon
socket head cap bolts (M3 x 12).
[NOTE]
The fine/coarse focus block can be installed to the microscope in both (right and left)
directions. Be sure to install it in the same orientation as disassembling.
5-3-2. Assembling Elevation Block (For 50i/55i)
Hexagon socket
head cap bolts
(M3 x 12) (#52)
Fine/coarse focus block Rack
Gear
Plastic cover
Fine/coarse
focus block
Standard holes
Pins
Bottom view
Limit screw: To be assembled
at this position
5. Disassembling/Assembling/Adjusting R-4758.B
40
[Checking the assembly position of coarse/fine focus drive]
When the elevator is at the highest position,
its edge should be approximately 1 mm
higher than the edge of #402.
Lateral view
30. Put the two claws on right and left sides of the plastic cover (#411) into the two
longitudinal holes of the plastic cover (#410).
31. Tighten the plastic cover using the two hexagon socket head cap bolts (M3 x 10).
32. Tighten the bottom cover using the five
special hexagon bolts (M3 x 6).
Hexagon socket head cap bolts (M3 x 10)(#51)
Longitudinal holes
Claws
Special hexagon bolts
(M3 x 6) (#239)
Bottom cover
Special hexagon bolt
(M3 x 6) (#239)
#402 1mm
elevator
Edge of #402 Edge of elevator
5-3-2. Assembling Elevation Block (For 50i/55i)
5. Disassembling/Assembling/Adjusting R-4758.B
41
33. Return the microscope to the horizontal position.
34. When the coarse focus knob and the fine focus knob are turned, check that the
elevation block moves smoothly.
35. When the elevation block is pushed down by hand, check that it moves smoothly.
Check that the elevation block is locked when the elevation block is fully pushed down,
and that the elevation block is moved upward when the elevation block is pushed
down again.
36. In the case of 50i, assemble the power supply assembly. (Refer to Section 5-9.)
In the case of 55i, assemble the control board of the light source unit. (Refer to
Section 5-14.)
37. In the case of 55i, perform the LED position adjustment. (Refer to Section 5-21.)
38. Tighten the plastic cover using the four hexagon socket head cap bolts (M3 x 6).
39. Install the cap.
40. In the case of 50i, connect the lamp to the lamp socket.
41. Move the lamp cover in the opposite direction of the arrow, and install it to the plastic
cover.
42. Install the hexagonal driver to the plastic cover.
43 Install the stage. (Refer to Section 5-2.)
44. Install the nosepiece. (Refer to Section 5-2.)
45. Install the condenser lens. (Refer to Section 5-2.)
46. Install the objective lens.
47. Install the eyepiece tube. (Refer to Section 5-2.)
Lamp cover (#223)
5-3-2. Assembling Elevation Block (For 50i/55i)
Cap (#233) Plastic cover (#202)
Special
hexagon bolts
(M3 x 6) (#254)
Lamp (#227)
Hexagonal driver (#248)
5. Disassembling/Assembling/Adjusting R-4758.B
42
- Disassembling the condenser holder block is not usually necessary, but if liquid (water
etc.) has dropped into the microscope, it should be disassembled.
- The two dovetails (#437 and #438) fixed to the condenser holder block must not be
disassembled at the same time. When re-assembling the dovetail, the other
(assembled) dovetail is used as a reference for assembling.
- Some screws are fixed with adhesive. Apply alcohol to melt the adhesive on these
screws.
WARNING (For ECLIPSE 50i)
- When disassembling the condenser holder, remove the elevation block from the
microscope base.
Be sure to keep the items described in WARNING of the elevation block.
(Refer to Section 5-3.)
5-4-1. Disassembling
1. Remove the elevation block from the
microscope base according to the steps 1
to 18 of Disassembling in elevation block.
(Refer to Section 5-3.)
2. Remove the three hexagon socket head
cap bolts (M3 x 8) (#442), and remove the
condenser holder block from the elevation
block.
3. Loosen the set screw (#446), and pull out
the lever (#439).
4. Loosen the set screw (#446), and pull out
the knob block of the condenser holder
block.
5-4-1. Disassembling Condenser Holder Block (For 50i/55i)
Hexagon socket
head cap bolts
(M3 x 8)(#442)
Condenser
holder block
Lever (#439)
Set screws
(#446)
Condenser holder Knob
5. Disassembling/Assembling/Adjusting R-4758.B
43
5. Remove the hexagon socket head cap bolt
(#445) of the stroke limitation screw.
6. Slide the condenser holder block to
remove it from the block (#422).
7. Remove the two hexagon socket head cap
bolts (M3 x 6) (#441), and remove the
dovetail (#437 or #438).
[NOTE]
When reassembling the dovetail, the other
(assembled) dovetail is used as the
reference for adjustment.
8. If there is a rusty section on the mounting surface of the dovetail and block, scrape it
using a scraper.
Disassembling male dovetail (#455) and rack (#456)
9. Remove the two hexagon socket head cap
bolts (M3 x 8) (#442), and remove the
male dovetail (#455) from the condenser
holder block.
5-4-1. Disassembling Condenser Holder Block (For 50i/55i)
Hexagon socket
head cap bolt (#445)
(Stroke limitation screw)
Condenser holder
Block (#422)
Dovetail (#438) Dovetail (#437)
Hexagon socket head
cap bolts (M3 x 6) (#441)
Block (#422)
Male Dovetail (#455)
Hexagon socket head cap
bolts (M3 x 8) (#442)
Condenser holder
5. Disassembling/Assembling/Adjusting R-4758.B
44
10. Remove the two special hexagon bolts
(M3 x 4) (#457), and remove the rack
(#456) from the removed male dovetail.
Disassembling condenser receptacle (#421)
11. Remove the set screw (#444).
12. Fully loosen the two knobs (#A6).
13. Remove the two hexagon socket head cap bolts (M3 x 6) (#441), and remove the
spring retainer (#436).
14. Remove the condenser receptacle (#421) from the condenser holder.
[NOTE]
The plate spring (#435) is removed at the same time.
5-4-1. Disassembling Condenser Holder Block (For 50i/55i)
Rack (#456) Special hexagon bolts
(M3 x 4)(#457)
Male Dovetail (#455)
Condenser holder
Knobs (#A6) Set screw (#444)
Spring retainer (#436)
Condenser holder
Hexagon socket head
cap bolts (M3 x 6) (#441)
Condenser holder
Condenser
receptacle
(#421)
Plate spring (#435)
5. Disassembling/Assembling/Adjusting R-4758.B
45
Disassembling knob block
15. Loosen the set screw (#446) fixing the
knob (#428).
16. Turn the knob counterclockwise to
remove it from the gear (#426).
[NOTE]
When removing the knob, the two special
washers (#429), Belleville spring (#430)
and special washer (#440) might fall. Be
careful not to lose them.
17. Remove the shaft supporter (#424) from
the gear.
The disassembly of the condenser holder block is completed.
The disassembled parts should be washed and cleaned.
5-4-1. Disassembling Condenser Holder Block (For 50i/55i)
Set screw (#446)
Knob (#428)
Gear (#426)
Remove two special washers (#429),
Belleville spring (#430) and special
washer (#440).
Gear (#426) Shaft supporter (#424)
5. Disassembling/Assembling/Adjusting R-4758.B
46
5-4-2. Assembling
When the male dovetail, rack, condenser receptacle, and knob were removed, assemble
these parts first, and then assemble the condenser holder according to the steps 1 to 13.
The assembling procedures for the male dovetail, rack, condenser receptacle and knob
are as follows:
- Assembling for male dovetail and rack: steps 14 to 17
- Assembling for condenser receptacle: steps 18 to 22
- Assembling for knob: steps 23 to 28
1. Lightly tighten the removed dovetail (#437
or #438) to the block using the two hexagon
socket head cap bolts (M3 x 6).
2. Insert the male dovetail on the condenser
holder to the block. While pushing the two
dovetails inside, tighten the two hexagon
socket head cap bolts.
[NOTE]
Move the condenser holder block in the
direction of the arrows, and tighten the
hexagon socket head cap bolts.
3. Move the condenser holder block in the
arrow directions, and check that the
condenser holder block moves smoothly
and lightly without slack.
If the condenser holder block does not
move smoothly and lightly without slack,
perform step 2 again.
4. Apply lubricant G7826 to the sliding
surfaces of the dovetail.
5-4-2. Assembling Condenser Holder Block (For 50i/55i)
Dovetail (#438) Dovetail (#437)
Hexagon socket head
cap bolts (M3 x 6) (#441)
Block (#422)