Beruflich Dokumente
Kultur Dokumente
0
SECTION X - STANDARD SCHEDULE OF RATES
GENERAL PREAMBLES
1. The clauses in the General Preambles shall apply to all work items contained in the Standard
Schedule of Rates.
2. All rates include the allowance for complying with the General Preambles and Specifications.
3. All rates contained in the Standard Schedule of Rates are exclusive of any Goods and Service Tax.
Any such Goods and Service Tax shall be borne by the Employer as and when the same becomes
due and payable.
4. All works, materials and goods described in this Schedule of Rates shall be of the respective kinds
described in the Contract and shall conform to the Specifications, Public Utilities Board, Energy
Market Authority and other relevant Statutory Requirements and to be approved by the
Superintending Officer.
5. The description given for each item shall unless otherwise stated, be held to include the use of
materials, labour, transport, equipment, tools, mobile lifting work platform, boom lift, hacking, supply
of fuel and all idle time, conveyance, delivery, unloading, storing, hoisting, stools/ladders, all labour
for setting, fitting, fixing in position, connection, all cutting and waste, return of packings,
establishment charges, overheads, profit and all forms of claim for loss and expenses, labour for
preparing surface to receive work, dismantling, protecting materials and work, making good all
affected works and disposal of fittings including checking, tracing and clearing of fault (if any)
before installation and testing after installation.
6. All rates in the Schedule shall include all necessary stagings and scaffoldings (only applicable up to
6 metres high, any height above 6 metres shall be paid separately, measuring from ground level,
i.e. from the base for which scaffolding rests) unless specified otherwise.
7. All rates in the Schedule shall be applicable for new and replacement works unless otherwise
stated. The rate for each item for the installation/fixing of parts/fittings shall unless otherwise stated,
deemed to include all staples, clips, screws bolts, rawl plug ramset brackets and other fixing
accessories necessary for the satisfactory completion of the installation works.
8. Unless otherwise stated, all works shall be measured nett as fixed in its place.
9. If there is any disagreement between the Employer and the Term Contractor on any of the items,
the Employer’s assessment shall be taken as final.
10. The term “as specified” means as specified in all Specifications, Works Order and/or drawings.
1
STANDARD SCHEDULE OF RATES
GENERAL PREAMBLES
12. Where brand, trade names or catalogue numbers are given in the description, they are solely
intended for fixing the rates of the Items. The products and materials to be used in the Contract
shall be governed by the specifications, drawings, other documents forming the contract and/or
subject to the approval of the Superintending Officer.
13. Daywork’s Schedule of Rates for LABOUR and PLANTS (Items U001 to U010) is inclusive of 15%
Establishment Charges and Profit. The contract percentages adjustment shall also apply.
14. For computation of ‘STAR’ rate using Daywork’s Schedule of Rates, the contract percentages
adjustment shall NOT apply to the ‘STAR’ rates computation.
15. In the case of claim under dayworks, the Contractor shall keep proper records of the names,
occupations and working hours of all workmen employed for such work and the quantities and
descriptions of all materials and plant employed. Such records, receipts or vouchers must be
verified by the Superintending Officer’s Representative before payment can be effected. Provided
always if the Superintending Officer’s Representative shall consider that for any reason the keeping
of such records, receipts and vouchers by the Contractor as required was impracticable, he shall
nevertheless be entitled to authorize payment for such work either as daywork (on being satisfied
as to the time employed and plant and materials used on such work) or at such value thereof as he
shall consider fair and reasonable.
2
A LIGHTING AND FAN POINT
3
SOR Page A1
A00l * Surface wiring of 2.5 mm2 PVC sheathed cables and 2.5mm2 PVC earth No. 18.35
cable in PVC trunking including surface mounted white plate switch with pvc
mounting box but excluding ceiling rose, light fitting, fan regulator and fan:
*(A001 A007)
A002 One lighting or fan point controlled by a 1-gang switch ( trunking run not No. 25.35
exceeding 8m)
A003 One lighting or fan point controlled by a 1-gang switch (trunking run exceeding No. 36.50
8m but not exceeding 12m)
A004 Two lighting or fan points controlled by a 2-gang switch (trunkinq run not No. 58.65
exceeding 12m)
A005 Three lighting or fan points controlled by a 3-gang switch (trunking run not No. 11.20
exceeding 18m)
A006 Each additional lighting or fan point in one loop switch circuit to items A001 to No. 22.30
A004 ( trunking run not exceeding 5m )
A007 Each additional lighting or fail point in one looping circuit to items A00l to A004 No. 31.80
(trunking run exceeding 5m but not exceeding 10m)
A008 One lighting point or fan point controlled by a two 2-way switch (trunking run No. 43.90
not exceeding 12m)
* Surface wiring of 2 x 2.5mm2 PVC sheathed cables and 2.5mm2 PVC earth
cable in 20mm diameter galvanized steel conduit including surface mounted
metal clad plate switch with mounting box but excluding ceiling rose, fitting, fan
regulator and fan: *(A008 A0l4)
One lighting or fan point controlled by a 1-gang switch (conduit run not
exceeding 8m)
1
SOR Page A2
A009 One lighting or fan point controlled by a 1-gang switch (conduit run exceeding No. 57.50
8m but not exceeding 12m)
A010 Two lighting or fan points controlled by a 2-gang switch (conduit run not No. 64.60
exceeding 12m)
A011 Three lighting or fan points controlled by a 3-gang switch (conduit run not No. 98.05
exceeding 18m)
A012 Each additional lighting point or fan point in one looping circuit to items A008 No. 22.30
to A011 (conduit run not exceeding 5m)
A013 Each additional lighting or fan point in one looping circuit to items A008 to A01l No. 42.50
(conduit run exceeding 5m but not
exceeding l0m)
A014 :One lighting or fan point controlled by two 2-way switch (conduit run not No. 71.45
exceeding 12m)
* Surface wiring of 2 x 2.5mm2 PVC sheathed cables and 2.Smrn2 PVC earth
cable in 20mm diameter PVC conduit including surface mounted metal clad
plate switch with mounting box but excluding ceiling rose, fitting, fan regulator
and fan: *(A01 A021)
One lighting or fan point controlled by a 1-gang switch (conduit run not
A015 No. 25.40
exceeding 8m)
A016 One lighting or fan point controlled by a 1-gang switch (conduit run exceeding No. 32.70
8m but not exceeding l2m)
A017 Two lighting or fan points controlled by a 2-gang switch (conduit run not No. 40.50
exceeding 12m)
A019 Each additional lighting point in one looping circuit to items A0l5 to A0l8 No. 9.50
(conduit run not exceeding 5m)
2
SOR Page A3
A020 Each additional lighting or fan point in one looping circuit to items A0l5 to A018 No. 18.90
(conduit run exceeding 5m but not exceeding 10m)
A021 One lighting or fan point controlled by two 2-way switch (conduit run not No. 52.70
exceeding 12m)
Items A022 to A027 are for the installation of new public lighting points. The
application of any combination of items A022 to A027 in a single works order
shall not exceed a total of 30 nos. per building block. Lighting point exceeding
30 nos. per building block shall
be built-up from other sections of the Schedule of Rates
* Surface wiring for one public lighting point comprising 3 x 2.5mm2 PVC
sheathed cables in PVC trunking of the following trunking run (ceiling rose,
mounting block and wiring in pipe conduit to be measured separately):- *(A022
A027)
A022 Not exceeding 10m per point (applicable for not more than 5 nos. of lighting No 21.55
point per block)
A023 Not exceeding 10m per point (applicable for between 6 to 10 nos. of lighting No. 21.10
point per block)
A024 Not exceeding 10m per point (applicable for between 11 to 15 nos. of lighting No. 20.85
point per block)
A025 Exceeding 10m but not exceeding l6m per point (applicable for more than 5 No. 34.00
nos. of lighting point per block)
A026 Exceeding 10m but not exceeding 16m per point (applicable for between 6 to No. 33.55
10 nos. of lighting point per block)
A027 Exceeding 10m but not exceeding 16m per point (applicable for between 11 to No. 33.30
15 nos. of lighting point per block)
3
B NOT IN USE
1
C NOT IN USE
1
D CONDUIT, TRUNKING AND CABLE TRAY
1. Conduit Dl
2. PVC Trunking Dl
3. Metal Trunking D2 – D3
4. Cable Tray D3
1
SOR Page D1
20mm
D001 m 3.70
25mm
D002 m 4.40
32mm
D003 m 5.90
* Super high impact heavy gauge PVC conduit of the following diameter fixed
to wall or ceiling complete with spacer bar, saddle, inspection box,
junction/bend/tee, elbow and joint accessories :- *(D004 D007)
1
Item Description Unit Rate ($)
SOR Page D2
METAL TRUNKING (Ekko, Sakiya, Li-Soon, Ega, EM Industries)
* Electro-galvanized metal trunking finished in epoxy. paint complete with coupling,
detachable cover, screws and joint accessories including fixing to walls or ceilings of the
following size :- *(0014 0034)
D014 m 8.50
1.2mm thick 50mm x 50mm
m 10.10
D015 1.2mm thick 75mm x 50mm
m 11.25
D016 1.2mm thick 75mm x 75mm
m 10.40
D017 1.2mm thick 100mm x 25mm
m 11.60
D018 1.2mm thick 100mm x 50mm
m 13.00
D019 1.2mm thick 100mm x 75mm
m 16.10
D020 1.2mm thick 110mm x 100mm
m 14.50
D021 1.2mm thick 125mm x 50mm
m 13.00
D022 1.2mm thick 150mm x 25mm
m 15.90
D023 1.2mm thick 150mm x 50mm
m 17.60
D024 1.2mm thick 150mm x 75mm
m 19.50
D025 1.2mm thick 150mm x 100mm
m 23.75
D026 1.2mm thick 150mm x 150mm
m 18.55
D027 1.2mm thick 175mm x 50mm
m 19.80
D028 1.2mm thick 200mm x 50mm
m 20.30
D029 1.2mm thick 200mm x 75mm
m 24.20
D030 1.2mm thick 200mm x 100mm
m 21.45
D031 1.2mm thick 225mm x 50mm
m 23.40
D032 1.2mm thick 250mm x 50mm
m 25.30
D033 1.2mm thick 300mm x 25mm
m 26.90
D034 1.2mm thick 300mm x 50mm
2
SOR Page D3
CABLE TRAY
* Hot dipped galvanized perforated mild steel cable tray of the following size
including hanger, support and fixing :- *(D043 D047)
CONDUIT PIPIE FOR ROAD CROSSING * UPVC class “C” pipe of the
following diameter for road crossing laid in trench (trench measured
separately) :- *(D048 D051)
m 1.70
D048 50mm
m 2.90
D049 80mm
m 4.50
D050 100mm
m 7.20
D051 150mm
3
SOR Page D4
4
E SWITCH, SOCKET OUTLET-AND CONSUMER UNIT
1. Switch El
2. Isolator El — E2
3. Socket Outlet E2
4. Plug E2
1
SOR Page E 1
SWITCH
E001 PVC mounting box for switch or socket outlet Cl gang or 2 gang) No. 0.95
E009 20 Amp DP water heater switch with pilot lamp No. 15.50
ISOLATOR
* Metal Clad or weatherproof Isolator
Switch of the following
(MEM, SMB, S-Team, ABB, Hager)
*(E011 E014)
1
SOR Page E 2
SOCKET OUTLET
FUSED PLUG
2
SOR Page E 3
E036 Metal clad split load consumer unit with 32 or 63A Amp OP isolator No. 194.00
2 x 20A SP MCB, with 40 or 63Amp OP RCCB (30 to 100 MA) 6 x
5/20 Amp 6KA SP MCB (ABB Mem, Sunlight, SMB, S-Team)
3
F NOT IN USE
1
G NOT IN USE
1
H INDOOR LUMINAIRE/LIGHT FITTING
4. Recessed Light H3 — H4
5. Emergency Light H5
2
SOR Page H1
H001 Remove existing ceiling, column wall mounted or recessed No. 5.00
luminaire including reinstatement and disposal off site (New
luminaire to be measured separately)
H003 1 x 18W or 1 x 36W with EMA approved electronic ballast (Osram, No. 35.45
Vossloh Schwabe, Tridonic-Atco, Ultro, Helvar) in-lieu of low loss
ballast and capacitor
1
SOR Page H2
H014 1 x 18W or 1 x 36W with internal metal reflector, clear acrylic No. 29.70
prismatic diffuser
and ABS end cap
H015 1 x 18W with internal metal reflector clear acrylic prismatic diffuser, No. 42.00
ABS
end cap and approved electronic
ballast (Osram, Vossloh Schwabe, Triolonic
Atco, Ultrom Helvar) in-lieu of the low
lost ballast)
H016 1 x 36W with internal metal reflector clear acrylic prismatic diffuser, No. 46.00
ABS
end cap and approved electronic
ballast (Osram, Vossloh Schwabe, Triolonic
Atco, Ultro, Helvar) in-lieu of the low
lost ballast
2
SOR Page H3
RECESSED LIGHT
(Removal of existing luminaire to be
measured separately)
3
SOR Page H4
H039 Extra over item H028 to”H038 for using each no. of electronic No. 16.00
ballast in-lieu
of low loss ballast (Osram, Vosslon-schwabe,
Tridonic-Atco, Helvar, Ultro or other
approved)
H041 “INTERLUX” SS87213 recessed downlight silver reflector and No. 75.00
protection glass
with 2 x PLC 13W lamp & ballast
H045 “EUROTEC” RAPID 2l4-83N0 2 x 18W PLC recessed downlight No. 65.00
with metallized
polycarbonate reflector, fresnel lens
polycarbonate diffuser & integral
electromagnetic ballast, 1P44
H046 “DIL-CIKO” 17 recessed downlight ring diameter 185mm with 13W No. 105.75
PLC lamp
H047 Recessed round or square flush mounted! eyeball halogen No. 45.00
downlight in white, black
or brass finish with remote transformer
and lamp
H048 Square box light fitting 600mm x 600mm with 32W/40W circular No. 37.85
tube (daylight or
warm white)
4
SOR Page H5
EMERGENCY LIGHT
H051 Single-sided slim type using LED in lieu of fluorescent tube No. 115.00
H052 Emergency bulk head lighting with 2 x 8W tube and Nickel No. 116.40
Cadmium battery pack
(Maxspid, Simlite, Econhite, PNE, Samcom)
H054 Recessed self contained UFO emergency lighting with 1 x 10W No. 116.40
halogen lamp and 2
hour battery pack
(Maxspid, Simlite, Econlite, PNE)
H055 “PIILIPS” FGC Security lighting including PL 9W/llW lamp No. 129.60
H058 “FABRIKANT” 8003 twin obstruction light, lighting control box and Set 1164.00
change over relay
with bracket and 42mm dia. hot dipped
galvanised steel pipe mounted on roof deck
and secured by 3 Nos. stainless steel
cable support
H059 “HUBBELL” navigation obstruction light No. 700.35 cat no. BYMB- No. 700.35
36002-AHQ with 2 x 7AP53-R, red frenel lens, transfer relay, 2 x
100W lamp and mounted on navigation obstruction lightmast
5
SOR Page H6
H061 “THORN” F22 Twin Obstruction Light with change over relay and No. 780.00
lamps
H062 “THORN” OBSTA STI Omni-diectiona1 red low intensity No. 1050.00
obstruction light with
neon discharge tube (Photometry : more
than 32 cd)
H063 “THORN” OBSTA HI-STI Omni-directional red low intensity No. 1800.00
obstruction light with
neon discharge tube (Photometry more
than 32 cd)
H064 “BTI” L860 Series low Intensity red LEDs Obstruction Light No. 1800.00
H065 “HONEYWELL” H&P 0B20 Single Obstruction Light with red lens No. 320.00
cover and lamp
H066 “HONEYWELL” H&P 0B22 Twin Obstruction Lights with change No. 880.00
over relay and lamps
6
SOR Page H7
H075 250 - 400W Mercury, lens, louvre or wire guard No. 380.00
H077 250 - 400W SON/MBI, lens, louvre or wire guard No. 480.00
BRANDED LUMINAIRE
H080 “ARCLUCE” MONOS ceiling mounted luminaire with 18W No. 100.90
fluorescent tube, body in extruded
aluminum and reeded clear high impact
acrylic diffuser
H081 “ARCLUCE” MONOS ceiling mounted luminaire with 36W No. 134.00
fluorescent tube, body in
extruded aluminum and-reeded clear
high impact acrylic diffuser
H082 “ARCLUCE” MONOS 1021 with 36W fluorescent tube (1P40) oval- No. 135.80
shaped extruded aluminum
tubular system and reeded prismatic
diffuser
H083 “ARCLUCE” ORION 240, 2990-10, recessed downlight with 4mm No. 228.70
frosted glass protector
and 18W lamp
H084 “ARIES” CLASSIC MOD 683 wall mounted luminaire with 13W No. 93.85
PLC/l8W PLC lamp, die
cast aluminum body and acrylic diffuser
H085 “ARIES” CLASSIC MOD 684 wall mounted luminaire with die-cast No. 85.85
aluminum structure
and polyester powder coated paint and
l3W/18W PLC/SC 18W lamp
7
SOR Page H8
H086 “ASTRIUM” TV21Q decorative semi-recessed wall luminaire in cast No. 280.00
aluminum with
frosted polycarbonate diffuser and 2 x 10W
or 2 x 7W PLC lamps
H087 “BEGA” 2489 wall mounted luminaire with 13W PLC lamp and die- No. 221.40
cast aluminium body
H088 “BEGA” 2926 recessed wall mounted luminaire with 183W PLC No. 221.40
lamp, aluminium
alloy and stainless steel body
H089 “BEGA” 2491 wall light (1P45) with 26W PLC lamp No. 368.00
H090 “BERGNER & WEISER” art no. 7151.1(W) wall/ No. 141.10
ceiling mounted luminaire wtih die-cast
aluminum body, polycarbonate diffuser
and 13W TC-D lamp
H091 “BERGNER & WEISER” art no. 7l51.lM(W) wall/ceiling mounted No. 168.15
luminaire with
die-cast aluminum body, polycarbonate
diffuser and 13W TC-D lamp
H092 “BOLUCE” ASTRA 9323, wall mounted luminaire with 2 x 9W PL No. 146.45
lamps
H094 “COSMO” C 0380/218 cast aluminum ceiling mounted luminaire No. 160.05
with opal polycarbonate
diffuser with 2 x PLC 18W lamps
H095 “DAIKO” DWP 18642 updown wall light in cast No. 260.00
aluminum with diffuser with 18W PLC lamp
H096 “DAIKO” DWP-l865l wall light in cast aluminum with diffuser with No. 295.00
13W PLC
lamp
H097 “DEFA” NEPTUNE OO3AS 121201 wall/ceiling mounted luminaire No. 162.90
with 26W PLC lamp and
polycarbonate diffuser
8
SOR Page H9
H102 “DISANO” Model 2100 KENDO fluorescent luminaire with 36W No. 152.30
fluorescent lamp and
end cap
H103 “DISANO” Model 2100 KENDO fluorescent luminaire with 18W No. 135.80
fluorescent lamp and cap
H106 “EUROTEC” 220 561 1 x 150W metal halide down wall light body No. 550.00
made of compact and
sturdy corrosion resistant die-cast light
alloy, safety tempered glass lens, with
up-throw narrow beam and asymmetrical wide
beam down-throw, IP 65
H107 “EUROTEC” BLOCK 1 x 18W PLC recessed wall light with die-cast No. 150.00
aluminum housing,
stainless steel front panel, and UV
stabilized opal polycarbonate1diffuser,
IP55
H108 “EUROTEC” CIN-ECO/FL26 1 x 26W PLC wall mounted up/down No. 185.00
light with UV stabilize
polycarbonate prismatic diffuser,
super pure aluminum reflector & integral
magnetic ballast
H111 “EUROTEC’ TO5EOS 2 x 18W PLC surface mounted with white No. 165.00
pressed steel housing,
vacuum metallized silver anodized reflector
& integral electromagnetic ballast
9
SOR Page H10
H114 “GHIDINI” OVALLA Cat. No. BL 1101.1 wall mounted luminaire No. 92.15
with 2 x 9W or 2 x 11W
PL lamps
H115 “GHIDINI” OVALLA 1103 wall mounted luminaire with die-cast No. 101.85
aluminum body and
opal diffuser, side mounting and 2 x 9W or
2 x 11W PL lamps
H116 “GHIDINI” OVALLA 1104 wall mounted luminaire with die-cast No. 103.90
aluminum body
opal diffuser, end mounting and 2 x 9W or
2 x 11W PL lamps
H117 “GOCCIA 2898 wall light with 2 x 9W or 2 x 11W PL lamps No. 87.30
H119 “GOCCIA” TRIANGOLO 4322 wall/ceiling luminaire with 2 x 11W No. 135.40
PL lamps and
vandal-proof acrylic diffuser
H120 “GOCCIA” TRIANGOLO 4346 wall/ceiling luminaire with 2 x 18W No. 146.90
PL lamps and
vandal-proof acrylic diffuser
H121 “GOCCIA” TRIANGOLO 4380 wall/ceiling luminaire with 80W No. 160.70
metal halide mercury lamp
H122 “IGUZZINI GRID” 7058 (1P66) surface mounted fitting in die cast No. 140.00
aluminum frame and
frosted polycarbonate diffuser with 2 x
11W or 2 x 18W PLC lamps
H123 “ILMAS” STUDIO LINE 1 x 18W fluorescent luminaire with HF No. 63.50
Electronic ballast and daylight / warm white tube
H124 “ILMAS STUDIO LINE 1 x 36W fluorescent luminaire with HF No. 75.00
Electronic ballast
and daylight / warm white tube
H125 ‘INNOLUX° WMTL 9732118 wall mounted luminaire with die-cast No. 142.60
aluminum body,
polycarbonate diffuser and 18W PLC lamp
H126 “INNOLUX” S4509ll8 wall mounted lighting with die-cast aluminum No. 161.00
body, tempered
glass diffuser and 18W PLC lamp
H127 “INNOLUX” P1496126 wall mounted lighting with die-cast No. 197.90
aluminum, reeded glass
diffuser and 26W PLC lamp
No.
10
SOR Page H11
H128 “INNOLUX WP 157027 die cast aluminum weatherproof 1P55 with 215.35
pressed glass diffuser, anodised aluminium reflector and 2 x 7W
PL lamps
No.
H129 “INNOLUX’ WS 675918 wall mounted, aluminum luminaire with 215.35
18W PLC lamp, sand blasted glass and weatherproof 1P55 body
No.
H130 “ITT REISS” Square light SQL 300/211 ceiling mounted luminaires 106.70
with 2 x 11W PL lamps and polycarbonate diffuser
No.
H131 “KL LICHT KEGEL-HALB 1121, PLC wall mounted fitting with 18W 276.00
PLC lamp
No.
H132 ‘KL LICHT RADIUS” 1341, PL wall mounted mounted fitting with 253.00
11W PL lamp
No.
H133 “KL LICHT” ZYLINDER-QUADRO 1581 wall mounted luminaire 980.00
with 70W SON/5OW or 80W metal halide lamp, body in cast
aluminium and cylindrical opal UVstabilized polycarbonate diffuser
No.
H134 “KL LICHT” ZYLINDER-QUADRO 1583 wall mounted luminaire 1080.00
with 70W SON/5OW or 80W metal halide lamp, body in cast
aluminium with anti-glare louvres and built in cylindrical clear UV-
stabilized polycarbonate diffuser
No.
H135 “KL LICHT” TRAPEZ 5007 wall mounted luminaire with 70W 687.75
SON/80W or 125W metal halide lamp, body in cast aluminium and
frosted UV-stabilized polycarbonate diffuser
Set
H136 “LIGHTCRAFT” AGT 146/P3-2 Telescopic with 2 lanterns and 26W 533.50
PLC lamps
Set
H137 “LIGHTCRAFT” AGT 146/P3-1 Telescopic with 1 lantern with 26W 388.00
PLC lamp
Set
H138 “LIGHTCRAFT” AGT 180/P3-l Telescopic lantern with 26W PLC 320.10
lamp
No.
H139 “LK” SKOT MAXI wall/ceiling mounted luminaire with 70W SON or 360.00
80W metal
halide lamp, polycarbonate diffuser
and die-cast aluminum body
No.
H140 “LOCADI” ARTE STRIPES20l8 wall/ceiling mounted luminaire with 103.90
18W PLC or 26W PLC
or 2 x 9W PL lamps, die cast aluminum
housing and UV stabilised vandal proof
diffuser
No.
H141 “LOCADI” ARTE STRIPE S1010 wall/ceiling mounted luminaire 95.85
with 10W PL or 13W
PLC lamp, die cast aluminum housing and UV
stabilised vandal proof diffuser
H142 “LOCADI” ARTE GRID Ll018 wall/ceiling mounted luminaire with No. 103.90
18W PLC or 26W
PLC or 2 x 9W PL lamp, die cast aluminum
housing and IN stabilised vandal proof
diffuser
11
SOR Page H12
H143 “LOCADI” ARTE STRIPE S2010 wall/ceiling mounted luminaire No. 97.80
with 10W PL or
13W PLC lamp, die cast aluminum housing
and UV stabilised vandal proof diffuser
H145 “LUCERNE” 502 wall mounted luminaire with 2 x 11W PL lamps, No. 100.95
body in die-cast
aluminum and frosted UV-stabilized
polycarbonate diffuser
H146 “LUCERNE” 502 wall mounted luminaire with 2 x 13W or 2x 18W No. 108.95
PLC lamps, body in
die-cast aluminum and frosted UV-
stabilized polycarbonate diffuser
H148 “LUXLITE” wall cylinder WC 150 with 2 x 13W PLC lamps No. 236.40
H150 “LUMENAX WAVE” 9002 2 x 18W surface mounted fluorescent No. 88.00
luminaire with white powder
coated steel or aluminum back refelctor,
reeded ABS end-cap and end-cover, and
daylight/warm white tube
H151 “LUMENAX WAVE” 9003 1 x 36W surface mounted fluorescent No. 62.00
luminaire with white powder
coated steel or aluminum back refelctor,
reeded ABS end-cap and end-cover, and
daylight/warm white tube
H152 “MARCIO”-RAMA Code NX 4043 wall mounted No. 140.65 surface No. 140.65
luminaire with 70W SON or 80W
mercury vapour lamp, injection moulded
impact resistant polycarbonate housing,
clear injection moulded polycarbonate
diffuser with internal prisms and high
purity aluminum reflector (IP65)
H153 “MARCIO” (37226 & 00642) recessed downlight with die-cast No. 238.00
aluminum ring, polished
aluminum reflector, sand-blasted glass
diffuser and 2 x 18W PLC lamps
H154 MARCIO (SA4) ceiling/column-mount surface luminaire with die- No. 180.00
cast aluminum housing,
opal polycarbonate diffuser and 2 x 9W
PL lamp
12
SOR Page H13
H155 “MARCIO” (6749) column-mounted surface luminaire with die-cast No. 176.00
aluminum housing,
up-down visor, sand-biased polycarbonate
diffuser and 18W PLC lamp
H156 “MARCIO” 2081 wall-mount surface luminaire with pressured No. 388.00
aluminum housing opel tempered glass diffuser and 36W PLC
compact fluorescent lamp A
H158 “MAXRAY” MD2668-01 recessed wall washer downlight with No. 130.00
aluminum reflector and
18W PLC lamp
H160 “MERZ” horizontal downlight with 18W PLC lamp No. 68.85
H163 “MEYER” wall mounted luminaire 16322 with opalescent No. 97.85
white/transparent polycarbonate diffuser, reflector and 13W or 18W
PLC lamps
H164 “MODUS PET” 330 Code PN 112.9006 ceiling mounted luminaire No. 126.10
with 2 x 11W compact
fluorescent lamps, die-cast aluminium
base and ring with epoxy powder
coating, hammered aluminium
reflector and sand-blasted polycarbonate
diffuser.
H165 “NIBA” QUASAR ceiling mountd luminaire Cat No. 3688 with opal No. 114.45
diffuser, frame
in orange-Red, pc white base in self
extinguishing thermoplastic & external
stainless steel screws with 2D 28W warm-
white lamp
H166 “NORAL” EXPO IVA wall mounted luminaire with 26W PLC lamp or No. 494.70
50W/ 80W mercury super deluxe lamp, bracket and
acrylic diffuser
H167 “NORAL” MARBELLA wall mounted luminaire with 11W PL or 13W No. 98.95
PLC or 18W PLC or 2D 16W lamp and polycarbonate diffuser
H168 “NORAL” NORA lllF wall mounted luminaire with 13W or 18W PLC No. 577.15
lamp or 50W mercury super deluxe lamp and polycarbonate
diffuser
13
SOR Page H14
H169 “NORAL” PORTO wall mounted luminaire with 9W PL or 13W PLC or 18W No. 98.95
PLC or 2D 16W lamp and polycarbonate diffuser
H170 “NORAL” ROULETTE II A/F wall mounted luminaire in standard black or white No. 254.15
finish with smoke lens made of UV-stabilised polycarbonate and 13W SL lamp
H171 “NORAL” SAINT TROPEZ wall/ceiling mounted luminaire with 11W PL or No. 98.95
13W PLC or 18W PLC or 2D 16W lamp and polycarbonate diffuser
H172 “NORAL” SANTA CRUZ/MILANO wall/ceiling mounted luminaire with frosted No. 119.30
polycarbonate diffuser, silver reflector and 38W warmwhite or daylight Lamp
H173 ‘NORALT’ SEVILLA A/F wall mounted luminaire with 13W or 18W or 26W PLC No. 342.40
lamp and polycarbonate diffuser
H174 “NORAL” TORINO A/F wall mounted luminaire in standard black or white No. 254.15
finish with smoke lens made of UV-stabilized polycarbonate and 9W SL lamp
H175 “NORAL” TRUMPET F wall mounted luminaire with 9W PL lamp, bracket and No. 244.45
polycarbonate diffuser
H176 “NOVALUX” Type 5514 decorative wall mounted lurninaire of thermosetting No. 103.90
body with frosted diffuser and 18W PLC lamp
H177 “NOVALUX” Type 5512 decorative wall mounted luminaire of thermosetting No. 103.90
body with frosted diffuser and 2 x 11W PL lamps
H178 “NOVALUX” Type 5510 decorative wall mounted luminaire of thermosetting No. 107.90
body with frosted diffuser and 2 x 18W PLC lamp
H179 “OSRAM” Softlite 18W luminaires lamp Hl80 “PHILIPS” TCS 058/118 No. 180.00
fluorescent luminaire No. 69.85 with 18W TLD lamp, in HPF switch start
circuitry and opal diffuser
H181 “PHILIPS” TCS 058/236 fluorescent luminaire with 2 x 36W TLD lamp HPF No. 120.30
switch start circuitry and opal diffuser
14
SOR Page H15
H182 “PHILIPS” KOMBI PLB 211 wall mounted vandal - resistant luminaire with 2 x No. 148.40
11W PL lamps
H183 “PLANET COSMO” C0380/213 decorative ceiling /wall mounted luminaire in No. 90.00
cast aluminium with opal diffuser and 2 x 13W PLC lamp
H184 “PLATEK” LEIPZIG 05 wall mounted light fitting, body made of phospho- No. 577.15
chromate aluminium coated with polyester paint, UV-stabilized polycarbonate
lens and 11W PL or 13W PLC or 18W PLC lamp
H185 “PLEAID” 175-76122 recessed downlight with matt aluminium reflector and No. 165.00
decorative glass with 18W PLC lamp (without cone)
H186 “POLOMITI” Square ceiling luminaire with 2 x 9W PL or 2 x 11W PL lamps No. 110.60
H187 “PRISMA” PIUS OVALE 350 spilt wall mounted luminaire with die-cast No. 204.30
aluminium housing and UV stabilized polycarbonate diffuser
H188 “PROLUX” 1080.20 wall mounted fitting with 15W ELN compact fluorescent No. 104.75
lamp, 200mm clear globe and wall bracket
H189 “PROLUX” TX118 surface mounted tubular light fittings with 18W fluorescent No. 160.05
lamp and prismatic diffuser
H190 PULSAR 62030 ceiling mounted luminaire with die cast body 2 x 11W PL No. 98.00
lamps
H191 “RAAK” recessed downlight R14-0003 ring diameter 190mm with 18W or 21W No. 276.45
PLC lamp
H192 “ROYCE THOMSON” RTE/PS/KT photocell Kit H193 “SELUX” SX 432-17-2 No. 73.70
wall mounted luminaire No. 1010.00 with 50W/80W/125W mercury super
deluxe lamp/26W PLC lamp and polycarbonate diffuser
15
SOR Page H16
H194 “SELUX” Sx 472-20-2 Wall Mounted Luminaire in Black FInishing with clear No. 1388.00
cylindrical polycarbonate diffuser clear mirror louvre, cast aluminium filter &
80W HME mercury super deluxe lamp
H195 “SIEMENS” CAMEO light fitting with 2 x 9W or 2 x 18W PL lamps No. 130.00
H196 “SIEMENS” CAMEO with seperate lamp and gear compartment and energy No. 130.00
saving 2D 28W or 38W lamps
H197 “SIEMENS” MONSUN Damp-proof surface mounted luminaire with 36W lamp No. 68.00
H198 “SIEMENS” MONSUN Damp-proof surface mounted luminaire with 2 x 36W No. 95.00
lamp
H199 “SIEMENS HQL” Super Delux wall mounted fitting custodian with GRP body No. 230.00
injection moulded TJV-stabilized polycarbonate prismatic diffuser, white sheet
steel reflector and 80W mercury lamp
H200 “SIMES” Model 56005 ceiling mounted luminaire with 2 x 11W PL lamps No. 114.45
H201 “SIMES” Model S6008 ceiling mounted luminaire with 2D38W lamp No. 119.30
H202 “SIMES” #245 decorative waterproof surface mounted luminaire of 1P54 class No. 85.10
1 protection with body in die cast aluminium and 13W PLC lamp
H203 “SIMES” VEDO OVAL Art 6709 wall/ceiling mounted luminaire with 18W PLC No. 117.95
lamp and sand-blasted polycarbonate diffuser
H204 “SIMES” VEDO OVAL Art 6749 wall/ceiling mounted luminaire with 18W PLC No. 132.00
lamp and sand-blasted polycarbonate diffuser
H205 “SIMES” VEDO OVAL Art 6759 wall/ceiling mounted luminaire with 18W PLC No. 139.10
lamp and sand-blasted polycarbonate diffuser
H206 “SIMLITE” BS12O 1 x 18W surface mounted ceiling/wall fluorescent luminaire No. 44.00
with powder coated white waveform reflector, removable gear tray, male &
female connector, and daylight/warm white tube
16
SOR Page H17
H207 “SIMLITE” BS12OE 1 x 18W surface mounted ceiling/wall fluorescent No. 60.00
luminaire with powder coated white waveform reflector removable gear tray,
male & female connector, electronic ballast, and daylight/warm white tube
H209 “SIMLITE” BS140E 1 x 36W surface mounted ceiling/wall fluorescent luminaire No. 80.50
with powder coated white waveform reflector, removable gear tray, male &
female connector, electronic ballast and daylight/ warm white tube
H210 “SUPERCLUB” CLUB/DIAMOND light fitting with 2D 28 or 38W lamp & No. 77.60
accessories
“SUPER DELTA” OVALE/G (Prisma 1702) light fitting which 2 x 9W PL lamps No. 70.80
H211
No. 110.60
H212 “TERNO-LYRA” TL-M0445/11 decorative ceiling light with 11W PL Lamp
H213 TERMO! 0250/219 ceiling luminaire with diffuser with 2 x PL 9W lamps No. 110.60
No. 165.85
H214 “THORLUX” Cat No. PS 7952S Prismalette bulkheed luminaire with 2D 38W
or 28W lamp or 2 x PL 11W lamp
H2l5 “THORLUX” MERCIAN with 70W high pressure sodium lamp (MER9953) or No. 420.00
70W metal halide lamp (MER9954) or Dulux T/E 42W compact fluorescent
lamp
H216 “THORLUX” PASSLIGHT with glass cover and 80 or 125W Mercury lamp or No. 415.00
70W high pressure sodium lamp/metal halide lamp
H217 “THORLUX” PRISMATIC with glass cover and 50W mercury lamp (PR3049)
No. 250.00
H218 “THORLUX” PISMALUX with glass cover and 80 or 125W mercury 1amp or No. 380.00
50 or 70W High Pressure Sodium lamp or 70W metal halide lamp
17
SOR Page H18
H219 “THORLUX” HU-STYLE COM indirect lighting system 2 x 55W with electronic No. 820.00
control gear and lamps
H220 “THORN” FRAS 218 2 x 18W fluorescent luminaires with FRV 236 louvres No. 156.15
H221 “THORN” BERGAIVIE 100W Halogen wall mounted luminaire No. 120.30
H222 “THORN” CONCEPT A mounted luminaire with 26W PLC lamp No. 226.00
H223 “THORN” DIAMOND DM 28/38 with seperate lamp and gear compartment and No. 130.00
20 28W or 38W lamp
H224 “TX” 18W tubular fitting with 75mm diameter low loss ballast starter, No. 149.40
capacitor and L18/3l tube
H225 “VINIC” 18405/18305 surface mounted wall/ ceiling luminaire die cast No. 180.00
aluminium and opal diffuser with 26W PLC lamp and wall
bracket
H226 “VINIC” 17907/17909 wall mounted luminaire die cast aluminium with 70W No. 335.00
SON/metal halide lamp (IP55)
H227 “VINIC” 15602 surface mounted luminaire die cast body with white No. 157.00
polycarbonate diffuser and 2 x PLC 18W lamps
H228 “VINIC” 18004/18007 wall mounted luminaire die cast aluminium with 70W No. 430.00
SON/metal halide lamp (1P55)
H229 ‘VINIC’ 14101/14102/14103 surface mounted ceiling/wall luminaire similar to No. 243.70
‘WE-EF’ DB 259-DD-26(I) with 13/18/26W PL-C lamp
H230 ‘VINIC’ 14503 surface mounted ceiling/wall luminaire similar to ‘WE-EF’ DLG No. 240.00
259-00-26 with 26W PL-C lamp
H231 “WE—EF QLL-0259-DF-24 wall mounted luminaire with 24W Dulux lamp and No. 310.00
UV stabilised polycarbonate lens
H232 H232 “WE-EF” QLL-309-DF-36 wall mounted luminaire with 36W Dulux lamp No. 388.00
and UV stabilised polycarbonate lens
18
SOR Page H19
H233 ‘TWE-EF” QLL-309-DF-2/36 wall mounted with 2 x 36W Dulux lamp and UV No. 420.00
stabilized polycarbonate lens
H234 “WE-EF” QRL-309--E-50/80 wall mounted with 50 or 80 mercury super deluxe No. 588.00
lamp and UV stabilized polycarbonate lens
H235 “WE-EF” QRL-309-E-50/70N1.wall mounted luminaire with 50 or 70 SON lamp No. 600.00
and UV stabilized polycarbonate lens
H236 11WE-EF” DRB2S9-DD--13(I) recessed wall luminaire, corrosion resistant die- No. 234.00
cast aluminium alloy body and frame, finish in PAL polyester powder coat,
polycarbonate UV-stabilized and vandal
resistant diffuser, weatherproof 1P55 and durable silicone gasket and 13W
PLC lamp
“WE-EF” DR3259-DD-26(I) recessed wall luminaire, corrosion resistant die- No. 224.20
H238
cast aluminium alloy body and frame, finish in PAL polyester powder coat,
polycarbonate UV-stabilized and vandal
resistant diffuser, weatherproof 1P55 and durable silicone gasket and 26W
PLC lamp
H240 “WE-EF” DLB259-DD-18(I) surface wall luminaire, corrosion resistant die- cast No. 226.10
aluminium alloy body and frame, finish in PAL polyester powder coat,
polycarbonate UV-stabilized and vandal
resistant diffuser, weatherproof 1P55 and durable silicone gasket and 18W
PLC lamp
19
SOR Page H20
H242 “WE-EF” DLG 259-DD-26 surface mounted ceiling/wall luminaire similar to No. 240.00
‘VINIC’ 14503 with 26W PL-C Lamp
H243 “WE-EF” LIGHTSPIKE LSA 050-E-50/80 wall mounted luminaire with 50 or No. 820.00
SOW mercury super deluxe lamp, die cast aluminium body and UV stabilized
polycarbonate lens
H244 “WE-EF” LIGHTSPIKE LSA 050-E-70H wall mounted luminaire with 70W No. 850.00
metal halide lamp, die cast aluminium body and UV stabilized polycarbonate
lens
“ZYMI” 3923 decorative wall light with opal diffuser and 18W PLC lamp No. 180.00
H247
H248 “3E AMANDINE” 1580 decorative wall luminaire in cast aluminium with No. 180.00
frosted diffuser and 18W PLC lamp
H249 “3E1” 025 decorative updown wall light in cast aluminium lens with •l3W PLC
No. 285.00
and 18W PLC lamps and ballasts
H250 “LUMENAX WAVE” 900]. 1 x 18W surface mounted fluorescent luminaire with No. 60.00
white powder coated steel or aluminium back reflector,
reeded ABS end-cap and end-cover, HF electronic ballast and daylight/warm
white tube
H251 “LUMENAX WAVE” 9002 2 x 18W surface mounted fluorescent luminaire with No. 111.00
white powder coated steel or aluminium back reflector,
reeded ABS end-cap and end-cover, HF electronic ballast and daylight/warm
white tube
H252 “LUMENAX WAVE” 9003 1 x 36W surface mounted fluorescent luminaire with No. 80.50
white powder coated steel or aluminium back reflector,
reeded ABS end-cap and end-cover, HF electronic ballast and daylight/warm
white tube
20
I - FAN
2. Exhaust Fan I1
1
SOR Page I1
I. FAN
I001 Remove existing exhaust, ceiling or wall mounted fans including regulator if No. 9.70
any including reinstatement and disposal off site (New fan to be measured
separately)
EXHAUST FAN
* Supply and install new exhaust fan of the following size :- (Removal of
existing fan to be measured separately) *(1002 1004)
I003 Exhaust fan 450mm High Pressure (Industrial Type) No. 368.60
(1400 RPM) (KDK, National, Mitsubishi)
I
I004 Exhaust fan 600mm High Pressure (Industrial Type) No 776.00
(920 RPM) (KDK, National, Mitsubishi)
* Supply and install the following ceiling / wall fan (Removal of existing fan to
be measured separately) *(I005 I011)
No 158.10
I005 400mm diameter Auto rotating ceiling fan
(KDK, National, Mitsubishi)
II006 400mm diameter wall bracket fan with pull cord regulator and switch No. 135.80
(KDK, National, Mitsubishi)
I008 508mm diameter wall fan 240V, 1400 rpm 50Hz (wing-Ton Model 303, 240.55
No.
Imasu/Tornado Model DF 500-TW)
I009 635mm (25) diameter wall fan 240V, 1400 rpm 50 Hz (wing-Ton Model 303, No. 271.60
Imasu/ Tornado Model DF 650-TW)
1
SOR Page I2
I011 l.5m diameter sweep ceiling fan regulator and teak board (KDK, National, No. 72.70
Mitsubishi)
I012 Hook for ceiling fan installed to existing concrete ceiling including cutting No. 5.80
mortice in concrete
I014 Fan condenser for 400mm or 500mm diameter wall bracket fan in replacement No. 12.60
I015 Fan gear for industrial wall fan in replacement No. 72.75
FAN REPAIR/INSTALLATION
I I016 Repair/rewind of fan motor coil for 400mm or 500mm diameter wall bracket fan No. 38.80
I017 Take delivery from any store, transport, cut stem as required and fix fan and No. 31.20
regulator (hook not included)
2
J LAMP, BULB, TUBE & BALLAST
1. Bulb J1
2. Fluorescent Tube J1 – J2
1
Item Description Unit Rate ($)
BULB
J002 Candle bulb 15 - 60W 230V BC or ES, clear or frosted (Philip, Splendour, No. 1.40
Osram, , Tungram)
J005 100W bulb for roof top aviation light No. 2.50
J006 100 watts GLS coiled tungsten incandescent bulb with ES caps No. 4.35
for aircraft warning light
J007 GLS pear shape 25-100W 230V clear or frosted No. 1.50
J010 60-100W 16,000 hrs bulb for aircraft warning light No. 19.00
FLUORESCENT TUBE
J013 450/600mm 18W energy saving fluorescent tube (daylight) No. 1.60
(Philips, Hitachi, GE, Osram)
J014 900mm 30W energy saving fluorescent tube (daylight) No. 3.00
(Philips, Hitachi, GE, Osram)
J015 1200mm 36W energy saving fluorescent tube (daylight) No. 3.30
(Philips, Hitachi, GE, Osram)
1
Item Description Unit Rate ($)
J016 1500mm 58W energy saving fluorescent tube (daylight) of 230V No. 3.80
(Philips, Hitachi, GE, Osram)
J017 600MM 18W energy saving fluorescent tube (warm or cool white) (Philips No. 4.65
colour 83/84, GE, Osram Lumilux 31, Sylvania)
J018 900MM 30W energy saving fluorescent tube (warm or cool white) (Philips No. 5.05
colour 83/84, GE, Osram Lumilux 31, Sylvania)
J019 1200mm 36W energy saving fluorescent tube (warm or cool white) (Philips No. 4.50
colour 83, Osram Lumilux 31/21 Sylvania, GE)
J026 T5, 15mm 4-8W daylight tube (Osram, Hitachi, National) No. 6.00
J027 T8, 26mm 18-36W daylight tube (Osram, Hitachi, Nationa) No. 5.60
J030 Lampholder for fluorescent lamp (all tube diameter and Sizes) Pair 1.95
J031 Starter for fluorescent lamp (Philips, Osram, Megaman) No. 1.05
2
Item Description Unit Rate ($)
J038 Flat prismatic/reeded/opal/frosted diffuser only for recessed light (Simlite, No. 32.00
Davis, Trimex, Woolite)
J039 End cap or decorative cap of ABS materials for 1 x 18W / 36W fluorescent No. 4.00
luminaires
J040 5-11W 2 pin (GE Biax-S, Osram Dulux-S, Philips PLS, Sylvania Lynx-S) No. 8.50
J041 5-11W 4 pin (GE Biax-S/E, Osrarn Dulux-SE, Philips PLS, Sylvania Lynx-SE) No. 12.00
J042 10-26W 2 pin (GE Biax-D, Osram Dulux-D, Philips PLC, Sylvania Lynx-D) No. 13.50
J044 13-26W 2 pin (GE Biax-T, Osram Dulux-T or T/IN, Philips PLT, Sylvania Lynx- No. 16.00
T)
J046 13-26W 4 pin (GE Biax-T/E, Osram Dulux-T/E or TIE/IN, Philips PLT, Sylvania No. 26.00
Lynx-TE)
3
Item Description Unit Rate ($)
J047 32-42W 4 pin (GE Biax - T/E, Osram Dulux-T or T/E/IN, Philips PLT, Sylvania No. 32.00
Lynx-TE)
J048 18-36W 2 pin or 4 pin (GE Biax-L, Osram Dulux-L, Philips PLL, Sylvania Lynx- No. 25.00
L-LE)
J049 40-55W 2 pin or 4 pin (GE Biax-L, Osram Dulux-L, Philips PLL, Sylvania No. 28.00
Lynex-L-LE)
J051 7-11W (GE Electronic Biax D or M, Osram Dulux-EL, Philips PLEU, Sylvania No. 25.00
Mini Lynx)
J052 15-25W (GE Electronic Biax T, Osram Dulux- EL, Philips PLET) No. 28.00
J054 10W to 40W 2D warm white or daylight. fluorescent lamp 2 or 4 pin No 15.50
(GE, Thorn)
J056 2 pin or 4 pin type compact fluorescent tube/2D fluorescent’s lamp holder No. 4.25
J057 Screw mounting type compact fluorescent tube’s holder No. 5.25
HALOGEN BULB/LAMP/TUBE
J058 35mm Halogen lamp l2V 20W-50W (Osram, Philip, Thorn) No. 7.75
J059 51mm Halogen lamp 12V 20W-SOW (Osram, Philip, Thorlux) No. 9.00
4
Item Description Unit Rate ($)
J063 60-250W E27 230V clear or frosted * Halogen par E27 230V of the following :- No. 36.00
(Philips, Osram, Sylvania, GE) *(J065 J066)
J065 Par 30 75-100W Spot or flood* Halogen Capsule l2V of the following :-
(Osram, Philips, GE, Sylvania) *(J067 J069)
J069 Halogen Lamp Accessories Ceramic holder for 50W/20W halogen / bulb / No. 7.00
lamp
J070 l2V transformer 50VA to 75VA for halogen lamp (Vossloh-Schwabe, Optima, No. 8.00
TCI)
J071 LAMP FOR GARDEN/STREET LIGHTS * High Pressure Sodium Vapour SON No. 3.10
lamp with E27/E40 base of the following :- (Osram, Philips, GE, Sylvania)
*(J072 J076)
J072 50-70W E27 (Elliptical or tubular, including built-in Igniter lamp) No. 24.00
J076 400W E40 (Elliptical or tubular) * Mercury Lamp with E27/E40 base (Osram, No. 55.00
Philips, GE) *(J078 J083)
No. 62.00
J077 160W BC or ES Blended/self-ballasted 230V
No. 12.90
J078 250W E40 Blended/self-ballasted 230V
No. 17.50
J079 50-125W
No. 12.90
5
Item Description Unit Rate ($)
J083 400W HPI Bus high pressure metal halide gas discharge lamp with E40 base, No. 96.80
“PHILIPS” or other approved type
* Metal Halide Lamp with E270 or E40 base
(Osram, HQI, Philips HPI/MHN-TD) *(J084 J089)
J084 70-150W double-ended Rx7s base (warmwhite, coolwhite, daylight) No. 78.00
J085 250W double-ended FC2 base (warmwhite, coolwhite, daylight) No. 130.00
J086 400W double-ended FC2 base (warmwhite, coolwhite, daylight) No. 160.00
J090 400W MBIF high pressure metal halide lamp G53455 igniter & E40, porcelain No. 165.85
lampholder, “THORN” or other approved type.
J091 250W MBIF metal halide lamp with metallic additives igniter & E40 base No. 145.50
“THORH” or other approved type
J092 200 watts E/27 Rough Device lamp bulb No. 14.55
J093 Low loss ballast 18W to 36W for fluorescent and 2-D lamp or 9W to 26W for No. 9.40
compact fluorescent lamp (ATCO, Helvar, Vossloh Schwabe)
6
Item Description Unit Rate ($)
* Non-Dimmable electronic ballast, PSB tested and PUB approved type for the
following :— (Osram, Schwabe, Helvar Tritronic) *(J095 J098)
J094 1 x 18W or 36W for TB 26mm diameter fluorescent lamp No. 35.00
J095 2 x 18W or 36W for T8 26mm diameter fluorescent lamp No. 55.00
J104 HPSV (SON) & Metal Halide 100W to 150W No. 39.30
J105 HPSV (SON) & Metal Halide 250W to 400W No. 56.60
OTHER LAMP ACCESSORIES Superimposed igniter for 70W to 400W high No. 38.00
J106
pressure sodium or metal halide lamp (Philips, Parmer, Bag Turgi, Thorn)
White moulded insulated bayonet-type batten lampholder, 5 Amp with skirt, 3 No. 4.45
J109
terminals and loop-in earth terminal similar to Delta Cat No. 1031 or other
approved
J110 White ceiling rose three terminals 5 Amp. similar to Delta Cat No. 1200 or No 4.85
other approved
7
K NOT IN USE
8
L NOT IN USE
5
M NOT IN USE
1
N FLOODLIGHT/STEPLIGHT/BURIED LIGHT/SPOTLIGHT
2. Floodlight/Steplight/Buried Light/spotlight N1 - N9
3. Mounting Bracket N9
1
SOR Page N 1
N. FLOODLIGHT/STEPLIGHT/BURIED LIGHT/SPOTLIGHT
FLOODLIGHT/STEPLIGHT/BURIED LIGHT/SPOTLIGHT
N002 “ARCLUCE” ECO 8137 slimline floodiight (1P55), black die cast aluminium No. 322.00
housing with cooling fins and 70W SON or 70W metal halide lamp
N003 “BERGER & WEISER” model no. 5203 outdoor corrosion resistant spotlight No. 46.10
with Par 38 cool beam 100W lamp and ground spike
N004 “BLAUET” 1910 recessed steplight in die cast aluminium with lourve No. 140.00
translucent
polycarbonate diffuser with 11W PL lamp
N005 “CING” CASTALDI D16/ECO steplight with 9W PL/l8W PLC/26W PLC lamp No. 151.10
and high stress resistant composite technopolymer body
N006 “DAIKO” DOD 75571 wall mounted spot luminaire with 150W HQI lamp and No. 920.00
antiglare shield
N007 “EYELITE” WALLUX MAXI SMS-7277 heavy duty die cast aluminium No. 425.00
luminaire with prismatic borosilicate glass diffuser and 70 to 150W SON or
metal halide lamp
1
SOR Page N 2
N009 “EUROTEC” RUDD DFPAR2OS 1 x 35W PAR2O MH 300K floodlight with No. 385.00
inground control gear, hexcell glare louver, die-cast aluminium in black zinc
coated stainless steel external hardware and tempered glass lens, IP67
N0l0 “EXTERIEUR VERT” M2 1P67 buried light, in 18 microns anodized No. 386.10
aluminium housing with mechanical resistance glass of 8T or anti vandal
polycarbonate 4T), FM 11W lamp, electronic control gear
N012 “HUBBELL” MAGNTJLITER floodlight Cat No. MVM-0250S-l16 with 250W No. 520.30
SON lamp and 4024C mounting bracket
N013 “HUBBELL” MINILITER floodlight Cat No. MHS-0070S-166 for 240V No. 382.30
operation with 70W SON lamp and 4024C mounting bracket
2
SOR Page N 3
N014 “IGUZZINI” PLATEA 7377 outdoor floodlight in die-cast aluminium, super No. 642.10
pure aluminium reflector with asymmetrical beam and 70W metal halide or
high pressure
sodium lamp
N015 “IGUZZINI” PLATEA 7378 outdoor floodlight in die-cast aluminium, super No. 657.70
pure aluminium reflector with asymmetrical beam and 150W metal halide or
high pressure sodium lamp
N0l6 “IGUZZINI” PLATEA 7395 outdoor floodlight in die-cast aluminium, super No. 738.20
pure aluminium reflector with asymmetrical beam and 250W metal halide
lamp
N017 “IGUZZINI” PLATEA 7379 outdoor floodlight in die-cast aluminium, super No. 577.15
pure aluminium reflector with flood beam and 70W metal halide or 80W -
125W high pressure sodium lamp
N018 “IGUZZINI” PLATEA 7380 outdoor floodlight in die-cast aluminium, super No. 612.10
pure aluminium reflector with flood beam and 150W metal halide or high
pressure sodium lamp
N019 “IGUZZINI” PLATEA 7394 outdoor floodlight in die-cast aluminium, super No. 677.10
pure aluminium reflector with flood beam and 250W metal halide lamp
N020 “IGUZZINI” 182° Uplighter Light Up Walk with 13W PLC lamp and die cast No. 602.40
aluminium frame
N021 “IGUZZINI” 7188/7189° Uplighter Light Up Walk with 50/80W mercury No. 717.80
super deluxe lamp respectively and die cast aluminium frame
N022 “IGUZZINI” 7180° Uplighter Light Up Walk with 50W white SON lamp and No. 893.40
die cast aluminium frame
N023 “IGUZZINI” 7178/7179° Uplighter Light Up Walk with 35/70W metal halide No. 828.40
lamp and die cast aluminium frame
3
SOR Page N 4
N024 “IGUZZINI” 7186/7187° Uplighter Light Up Walk with 50/70W SON lamp No. 828.40
and die cast aluminium frame
N025 “IGUZZINI” PLATEA 7382 outdoor floodlight in die cast aluminium super No. 438.10
pure aluminium reflector with flood beam and 70W metal halide E27 lamp
N026 “IGUZZINI” PLATEA 7384 outdoor floodlight in die cast aluminium super No. 426.80
pure aluminium reflector with flood beam and 80W metal halide lamp
N027 “IGUZZINI” PLATEA 7390 outdoor floodlight in die cast aluminium super No. 722.65
pure aluminium reflector with flood beam and SOW SON or metal halide
lamp
N028 “IGUZZINI” PLATEA 7376 outdoor floodlight in die cast aluminium super No. 471.40
pure aluminium reflector with flood beam and 2 x 26W TCT compact
fluorescent lamp
N029 “IGUZZINI” PLATEA 7385 outdoor floodlight in die cast aluminium super No. 592.70
pure aluminium reflector with spot beam and 70W metal halide lamp
N030 “IGUZZINI” PLATEA 7386 outdoor floodlight in die cast aluminium super No. 627.60
pure aluminium reflector with spot beam and 150W metal halide lamp
N031 “IGUZZINI” PLATEA 7387 outdoor floodlight in die cast aluminium super No. 717.80
pure aluminium reflector with blade-of-light beam and 70W metal halide
lamp
N032 “IGUZZINI” PLATEA 7388 outdoor floodlight in die cast aluminium super No. 753.70
pure aluminium reflector with blade-of-light beam and 150W metal halide
lamp
4
SOR Page N 5
N033 “INDALUX” 250-IQN security floodlight with die-cast aluminium housing, No. 463.00
borosilicate glass diffuser and 70W SON or metal halide lamp
N034 “INDALUX 600-IZX-C/S/D/A floodlight with 150W/250W/400W SON lamp/or No. 811.00
150W/25W/400W metal halide lamp
N035 “INNOLUX” S4440MH70 ground buried, aluminium luminaire, toughened No. 777.90
glass, weatherproof IP 67 with 70W metal halide lamp
N036 “INNOLUX” S4318 MH70 wall mounted aluminium floodlight tempered No. 1001.00
glass weatherproof IP 65 with SOW metal halide lamp
N037 “JETS 5” 84.09.01 outdoor flooding wit.h 250W high pressure sodium lamp No. 480.00
N038 “LIGMAN” 50031 spike mounted spotlight with 80W PAR 38 lamp No. 139.00
N039 “MARCIO” (1091) recessed step-light luminaire with 2 x 9W PL lamps, No. 242.00
pressured aluminium housing & guard, tempered glass diffuser and recess
box
N040 “MARCIO” (4440) buried uplighter luminaire with 70W metal halide lamp, No. 982.00
die-cast aluminium housing, reflector, polypropylene recess-tube and
toughened glass diffuser
N04l “MARCIO” (4316) floodlight luminaire with 70W metal halide lamp, die-cast No. 574.00
aluminium housing, reflector and 70W metal halide lamp
N042 “MARCIO” (4819) ground-mounted recessed luminaire with die-cast No. 642.00
aluminium housing, 12 windows protective guard, thoughened glass
diffuser, polypropylene recess tube and 18W PLC lamp
5
SOR Page N 6
N043 “MAZDA” CONDOR C3 MAIH 400 1P65 floodlight with 400W metal halide No. 423.90
(MAIH 400W) lamp, weatherproof metal enclosure and stirrup mounting
bracket
N044 “MAZDA” CORMORAN 400/1000 E40 floodlight with 250W/400W high No. 350.00
pressure sodium vapour or metal halide lamp, weather-proof metal
enclosure and stirrup mounting bracket
N045 “MEYER” WM 8872-041-000 Floodlight with thermal fatigue resistant safety No. 642.00
glass, high gloss mirror reflector, die-cast aluminium body & 150W metal
halide lamp
N046 “PHILIPS” floodlight Cat No. SWF 330 with 250W/400W SON/T lamp and No. 560.00
mounting bracket
N047 ”PHILIPS” anti glare weatherproof floodlight Cat No. SNF 300 with 250W No. 411.30
SON/T lamp
N048 “PHILIPS” anti glare weatherproof floodlight Cat No. SWF 330/SEF 330 No. 499.55
with 250W SON/T or 400W HDL/T lamp
N049 “PHILIPS” bulk head luminaire Cat No. XGCOO1 with prismatic diffuser, No. 163.90
18W SOX lamp and mounting bracket
N050 “SIEMENS” EUROFLOOD 701150 SICOMPACT mini floodlight with No. 544.20
70/150W metal halide or high pressure sodium lamp
N051 “SIEMENS” EUROFLOOD 250/400 •SICOMPACT mini floodlight with No. 636.30
250/400W metal halide or high pressure sodium lamp
N052 “SIEMENS” SICOMPACT MINI floodlight cat. no. 5NA-747-l-2 of die-cast No. 336.60
aluminium housing, hammered aluminium reflector and tempered glass
lens with 70W metal halide lamp
N053 “SIEMENS” SICOMPACT MINI floodlight cat. no. 5NA-747-2-2 of die-cast No. 351.10
aluminium housing, hammered aluminium reflector and tempered glass
lens with 150W metal halide lamp
N054 “SELUX” MTR luminaire Cat No. SX 563 11-2 with 70W SOI’ lamp, MTR No. 939.90
200 reflector and V accessories
6
SOR Page N 7
N055 “SIMES” Ring Drive/walk over Art S.4928/4929/4930 with thoughened clear No. 524.00
glass diffuser polypropylene tube for recess, 1P67 and 18W PLC-T lamp
N056 “SIMES’ MEGAFLAT round buried drive/walk over Art. S.4787 uplight with No. 754.00
70W SON or 125W mercury super deluxe lamp, polyester powder coated
cast aluminium housing and toughened glass
N057 “SIMES” MEGAFLAT round buried drive/walk over Art. S.4790 uplight with No. 962.00
clear thoughened glass diffuser, polypropylene tube for recess, 1P67 and
MM 150W metal halide lamp
N058 “SIMES” MEGAFLAT round buried drive/walk over Art S.4787/4726/4728 No. 1005.00
uplight with 1 x MH—1SOW/125W/70W metal halide lamp, clear toughened
clear glass diffuser, polypropylene tube for recess, 1P67
N062 “THORLUX” PASSLIGHT security floodlight Cat No. PL 6235 with die-cast No. 425.00
aluminium housing, primatic glass cover diffuser and 70W SON lamp/SOW
metal halide lamp
N063 “THORLUX” AZMET 70 Floodlight with 70W high pressure sodium lamp No. 420.00
N064 “THORLUX” COMBO Prismatic low glare refractor luminaire with No. 720.00
250W/400W sodium or 250W/400W metal halide lamp
7
SOR Page N 8
N070 “THORN” ODW 500 halogen floodlight with K1 250W/500W No. 159.00
linear tungsten halogen
lamp
8
SOR Page N 9
N077 “WE-EF” STO 259 step light with high impact opal acrylic lens, No. 188.00
13W/18W PLC lamp
N078 150/200W spot light fitting with base holder to wall or ceiling No. 27.65
MOUNTING BRACKET
N079 Mounting bracket for ‘PHILIPS’ SWF 330/ SEF 330 floodlight No. 38.15
N082 Steel mounting bracket for single flood light luminaire on post top No. 85.50
column
(other than WE-EF)
N083 Steel mounting bracket for two flood light luminaire on post top No. 133.00
column (other than WE-EF)
N084 “SIMES” Art S4929 ring buried/walk over light fitting with No. 425.00
acidated glass, die
cast aluminium body and 18W PLC-T lamp
N085 “SIMES” PRADO buried drive-over with compact fluorescent No. 188.00
lamp low G24d-1 die
cast aluminium body 4 windows protective
guard of 6mm thickness polypropylene tube
and polypropylene vandal proof diffuser
9
P WEATHERPROOF BOX ND METAL ENCLOSURE
8
SOR Page P 1
P003 “TVYNCKIER” Superpolyrel SP 430 1000 x 750 x 300 mm with No. 982.00
cover, rainhood, air vents,
handle, lock, keys and gasket for 1P55
P005 310 x 240 x 154 mm PVC rectangular box with hinged cover, No. 123.50
“LEGRAND” Cat. No. 35054
or other approved
P006 85mm x 85mm x 30mm PVC box with hinged cover, “LEGRAND No. 16.60
Cat No. 35054 or tolier
approved
P007 150mm x 100mm PVC rectangular terminal/ junction box No. 8.50
P011 Approved metal box for 13 Amp socket outlet No. 16.60
with hidden hinges, cam lock and 2 keys
1
Q NOT IN USE
1
R LABOUR ONLY ITEM
1
SOR Page R 1
R002 Checking defective wiring, fuse, time switch, etc in Job 17.80
switchroom/distribution
by skilled electrician including repair
where necessary in switch room/distribution
board (Parts measured separately)
R003 Checking defective lamp pole wiring, fuse, including tracing fault Pole 11.30
& repair where necessary
R004 Refixing loosen lamp cover/fitting for post top lantern No. 5.70
R008 Replumbing verticality of lamp post not Pole 38.00 exceeding 5m Pole 38.00
height including excavation, casting new concrete footing (where
necessary) painting of approved bituminous coating to surface of
ground section of column up to 150mm above ground level and
reinstate ground on completion
R009 Replumbing verticality of lamp post exceeding 5m but not Pole 62.00
exceeding 8m height
including excavation, casting of new
concrete footing (where necessary) painting
of approved bituminous coating to surface
of ground section of column up to 300mm
above ground level and reinstate ground on
completion
R010 Replumbing verticality of lamp post exceeding 8m but not Pole 70.00
exceeding l2m height
including excavation, casting new concrete
footing (where necessary) painting of
approved bituminous coating to surface
of ground section of column up to 300mm
above ground level and reinstate ground
on completion
R011 Tracing underground cable fault between two lamp poles or lamp Job 33.90
post and switchroom for series of lamp posts in circuit (repair
and parts measured seperately)
1
SOR Page R 2
R012 Checking fitness of carpark lighting including dismantling the No. 8.90
fitting,
replacing parts where necessary (parts
measured separately) cleaning fitting!
diffuser and refixing on completion
R013 Refixing loose and fallen teak battens including replacement of M 0.90
wall plugs where necessary
R014 Refixing loose and fallen wiring/PVC trunking including supply of M 0.90
additional clips
R015 Refixing loose or fallen ceiling rose including the replacement of No. 1.00
wood plugs where necessary
R017 Refixing loose electrical fittings and accessories including the No. 2.80
replacement of wood plugs where necessary
R018 Removing existing ceiling rose and connecting short length of No. 4.25
cable from
existing lighting point directly into
the existing light fittings inclusive of
short length of cable, trunking/conduit and
connector
R020 Checking and tightening the loose cable connection for fuses, Job 17.50
MCCB’s and busbars in the main switchboard
R021 Checking and repairing to defective light in community hail, No. 26.20
market, hawker centre or other parts of building exceeding 6m
height including use of metal scaffolding (parts and fittings
measured separately)
R022 Extra over item R02l for checking and repairing additional No. 6.30
defective light within
the same building including shifting of
scaffolding (parts and fittings measured
separately)
R023 Tracing fault in public lighting in building block including repair No. 5.65
where
necessary
2
SOR Page R 3
R027 Modifying existing fluorescent light fitting for installation of No. 5.50
electronic
ballast or low loss ballast including
supply of necessary wiring (Ballast
measured seperately)
R028 Taking down, removing and refixing ceiling fans and regulators in No. 10.10
new position not exceeding 200m distance (new fan point to be
measured separately)
R029 Taking down, removing and refixing ceiling fans and regulators in No. 15.50
new position exceeding 200m distance including transport (new
fan point to be measured separately)
R030 Taking down wall fan in hawker centre or other parts of any No. 11.35
building clean, oil, service & refix fan to original position after
work completion
R031 Checking firmness of ceiling fan bracket/hook, taking down No. 13.10
ceiling fans
in hawker centres or other buildings as
directed, dismantle the mechanical
connecting components to check for
worn boft/rivets, corroded hanging rod
and bolt assembly without split cotter pins
and replacing these parts (parts measured
separately) if necessary, including cleaning fans and ref ixing on
completion
R033 Servicing of additional air-circuit breaker within the same No. 350.00
switchroom as item R032
3
SOR Page R 4
R034 Servicing of air-circuit breaker (ACB) for work carry out after No. 650.00
office hour or on Saturday, Sunday and Public Holiday
R037 Servicing additional air-circuit breaker (ACB) within the same No. 700.00
switchroom including provision of generator for work carry out
after office hour or on Saturday,
Sunday and Public Holiday
R038 Repairing fallen or loose lightning conductor and reset it to its Job 24.25
original position including the use of securing material, additional
clips, etc. (1 job refers to whole block/linkway/
gateway/pavilion/link building etc)
R039 Repositioning of existing light fittings and lighting point with new Point 28.00
3 x 2.Smrn2 PVC sheathed cable in new PVC trunking including
removal of exising wiring and reinstatement (trunking run not
exceeding 10m)
4
S MISCELLANEOUS
1. Miscellaneous S1 — S2
1
SOR Page S 1
* S. MISCELLANEOUS
S001 Supply and fix approved powered drive masonry pin including No. 0.50
the use of cartridges
S005 Monthly rental rate for “Wildcat” self propelled work platforms No. 1552.00
Model 2032 with
working height of 7.9Dm, overall length
2.30m, platforms capacity 800 Lbs
including fuel and operator
1
SOR Page S 2
S011 Patch up openings for pipes/conduits exceeding 100mm dia but No. 4.60
not exceeding 225mm dia. with waterproof cement and sand
(1:3) mortar to wall and floor not exceeding 225mm thick and
make good to match existing
S012 Hack through existing rc slab not exceeding 225mm thick to form Opening 7.50
opening not exceeding 0.03m2 for trunking and reinstate to
match existing
S013 GS bracket for metal trunking fixed to ceiling or wall including No. 3.50
ramset nails and 2 coats of painting
S014 Polarised 10 Amp rated plug and socket connector No. 4.60
S015 SV A.C. relay (MY2 or MY4) for aircraft warning lights consol box No. 40.75
S016 “CRI” electric insect killer 80W (2 x 40W UVBL) Model : 308 No. 390.00
S017 40W ultra violet tube for CR1 electric insect killer, mode/308 No. 30.00
2
T EXCAVATION AND TRENCHING
1. Excavation T1
2. Demolition T1
3. Cover Plate T1
4. Turfing T1
1
SOR Page T1
EXCAVATION
(Reinstatement of turf to be paid
separately unless otherwise stated)
T002 Mechanical excavation of 300mm wide x 750mm deep trench for M 3.00
underground
cable including sand bed and backfilling
DEMOLITION
T006 Breaking up macadam road surface 600mm wide and not M 15.70
exceeding 450mm thick for laying underground cable including
taking up pitch block base and reinstate same on completion
T007 Breaking up reinforced concrete slab 600mm wide and not M2 26.70
exceeding 150mm thick for laying underground cable lapping
with new reinforcement on completion and reinstate to match
existing
COVER PLATE
TURFING
T010 Supply and turf good quality 25mm thick cow grass in close M2 2.90
turfing including 125mm
thick top soil and well watering and
tendering to ensure growth of turf
1
U – DAYWORK
1. Daywork Items U1 – U2
1
SOR Page U1
U. DAYWORK
U003 Services rendered by licensed cable detection worker for site Hr 109.00
excavation using
mechanical means for laying of
underground cables/erection of lighting
column for a minimum of 1 1/2 hours
U004 Injection test for 1 No. ACB/MCCB (with earth fault/overcurrent No. 750.00
protection) by
ENA registered testing engineer
including submission of shutdown form to
Powergrid Ltd, arrangement for
shutdown etc for testing and providing
temporary electrical supply and skilled
electrician, equipment and transportation
cost - during office hours i.e. 8.00 am
to 5.30 pm
U005 Injection test for each additional circuit breaker (with earth fault/ No. 500.00
overcurrent protection) within the same switchroom as item U004
U006 Injection test for 1 No: ACB/MCCB (with earth fault/overcurrent No. 1000.00
protection)
by EMA registered testing engineer
including submission of shutdown form to
Powergrid Ltd. arrangement for shutdown etc for testing and
providing temporary electrical supply and skilled electricians,
equipment and transportation cost - after office hours or on
Saturday, Sunday and Public Holiday
U007 Injection test for each additional circuit breaker (with earth No. 750.00
fault/overcurrent protection) within the same switchroom as item
U006
U008 Application and endorsement of Form CS/5 as licensed electrical Job 142.50
worker when requested by Superintending Officer for SP
Services Ltd testing for electrical extension/minor rewiring work
for the electrical installation
U009 Supply of EMA Licensed Cable Jointer to carry out “Livefl Job 142.50
termination of CTS cables at OG box
1
SUPPLEMENTARY
SCHEDULE OF RATES
1
SECTION XI - SUPPLEMENTARY SCHEDULE OF RATES
Preamble
to the respective Employer’s properties as and when directed by the Superintending Officer. The
Contractor shall provide all necessary labour, materials, plants, equipments, tools, transportation
and everything necessary, whether of a temporary or permanent nature for the manufacture,
testing and delivery of the goods to the respective Employers properties as and when directed by
the Superintending Officer
V00l Supply and deliver 600mm, 18W daylight fluorescent tube (Philips, No 2.00
Hitachi, Osram, Toshiba)
The preambles on Pages GP1 and GP2 for the standard schedule of rates shall be applicable for
the following items. The following items will be subjected to the percentage adjustment to the SOR
as indicated in the Form of Tender.
Rate
Item Description Unit
($)
Light Fittings (V028 to V036)
Neon Lightings
Supply and install the following neon light fittings:
V056 No. 150.00
8mm to 15mm diameter neon tube comprising two electrodes, inclusive of
dismantling and refixing the existing channel lettering
V059 One 13A switch socket outlet (1-gang) with wiring in 3 x 2.5m2 PVC sheathed No. 37.90
cables including 40 x 20 (mm) PVC trunking and surface mounted white plate
switchsocket outlet (trunking run not exceeding 12m)
One 13A switchsocket out (2-gang) with wiring in 3 x 2.5mm2 PVC sheathed
V060 trunking and surface mounted white plate switchsocket outlet (trunking run not No. 44.90
exceeding 12m)
One 13A metal clad switchsocket outlet (1- gang) with wiring in 3 x 2.5mm2 PVC
V061 sheathed cables including 20mm diameter galganised steel conduits and metal clad No. 64.30
switchsocket outlet (conduit run not exceeding 12m)
Item Description Unit Rate ($)
One 13A metal clad switchsocket outlet (1- gang) with wiring in 3 x 2.5mm PVC
V062 sheathed cables including 20mm dia PVC conduits and metal clad switchsocket No. 45.00
outlet (conduit run not exceeding 12m)
One 15A switchsocket outlet (1-gang) with wiring in 3 x 2.5mm2 PVC sheathed
V063 cables including 40 x 20 (mm) PVC trunking and surface mounted white plate No. 46.10
switchsocket outlet (trunking run not exceeding 12m)
One 15A metal clad switchsocket outlet (1- gang) with wiring in 3 x 2.5mm2 PVC
V064 sheathed cables including. 20mm dia galvanised steel conduits and metal clad No. 69.00
switchsocket outlet (conduit run not exceeding 12m)
One 15A metal clad switchsocket outlet (1- gang) with wiring in 3 x 2.5mm2 PVC
V065 sheathed cables including 20mm diameter PVC conduits and metal clad No. 49.50
switchsocket outlet (conduit run not exceeding 12m)
One 20A water heater point with wiring in 2 x 6mm2 PVC sheathed cable with
6mm2 PVC earth (green) cable including 40 x 20 (mm PVC trunking, surfaced
V066 No. 65.40
mounted water heater switch (MARKED WATER HEATER AND WITH PILOT
.
LAMP) and 20A connection unit (trunking run not exceeding 12m)
.
Air-Conditioning
V067 Supply labour, equipment and cleaning chemical to service fan coil unit of air- No. 53.33
conditioning system including chemical wash where necessary
Supply labour, equipment and cleaning chemical to service condenser unit of air
V068 No. 80.00
conditioning system including chemical wash where necessary
Supply labour and R22 refrigerant to re-charge compressor unit of air conditioning
V069 No. 33.33
system
Supply labour and equipment to temporarily remove single split air conditioning
V071 system including all existing cables, pipings, trunking etc and reinstall the same as No. 466.67
directed by the Superintending Officer including and commissioning
Supply labour and equipment to temporarily remove double split air conditioning
V072 system including all existing cables, pipings, trunking etc and reinstall the same as No. 666.67
directed by the Superintending Officer including and. commissioning
Supply labour and equipment to temporarily remove triple split A/C unit including
V073 all existing cables, pipings, trunking etc and reinstall the same as directed by the No. 1000.00
Superintending Officer including and commissioning
Supply & install stainless steel support bracket for condenser unit of multi-split air
V074 conditioning system including temporary removal of condenser unit and removal of No. 160.00
existing bracket if any
Supply & install of Emergency Call Bell with push-button or pull chord inclusive of
V075 notice stating “Emergency Call” complying with the code on Barrier Free No 180.00
Accessibility in buildings 2007
Supply & install of call bell or buzzer outside the compartment complying with the
V076 No 100.00
code on Barrier Free Accessibility in buildings 2007