Beruflich Dokumente
Kultur Dokumente
Refer to the exhibit. What can be concluded about network 192.168.1.0 in the R2
routing table?
This network was learned through summary LSAs from an ABR.*
This network should be used to forward traffic toward external networks.
This network is directly connected to the interface GigabitEthernet0/0.
This network has been learned from an internal router within the same area.
__________________________________________________________________
2
Which address is used by an IPv6 EIGRP router as the source for hello messages?
the interface IPv6 link-local address*
the all-EIGRP-routers multicast address
the IPv6 global unicast address that is configured on the interface
the 32-bit router ID
__________________________________________________________________
3
What are two differences between the Cisco IOS 12 and IOS 15 versions? (Choose
two.)
The IOS 12 version has commands that are not available in the 15 version.
The IOS version 15 license key is unique to each device, whereas the IOS version
Refer to the exhibit. Which three statements describe the results of the OSPF
election process of the topology that is shown in the exhibit? (Choose three.)
R2 will be elected DR.*
R3 will be elected BDR.*
The R4 FastEthernet 0/0 priority is 128.
The router ID on R2 is the loopback interface.
R1 will be elected BDR.
The R4 router ID is 172.16.1.1.*
__________________________________________________________________
6
What are two features of a link-state routing protocol? (Choose two.)
Routers create a topology of the network by using information from other routers.*
Routers send triggered updates in response to a change.*
The database information for each router is obtained from the same source.
Routers send periodic updates only to neighboring routers.
Paths are chosen based on the lowest number of hops to the designated router.
__________________________________________________________________
7
When are EIGRP update packets sent?
when learned routes age out
every 30 seconds via broadcast
every 5 seconds via multicast
only when necessary*
__________________________________________________________________
9
Which two statements correctly describe the components of a router? (Choose
two.)
RAM permanently stores the configuration file used during the boot sequence.
NVRAM stores a backup copy of the IOS used during the boot sequence.
Flash contains boot system commands to identify the location of the IOS.
Flash memory does not lose its contents during a reboot.*
ROM contains diagnostics executed on hardware modules.*
ROM contains the most current and most complete version of the IOS.
__________________________________________________________________
10
Which statement is correct about IPv6 routing?
IPv6 uses the link-local address of neighbors as the next-hop address for dynamic
routes.*
IPv6 routes appear in the same routing table as IPv4 routes.
IPv6 only supports the OSPF and EIGRP routing protocols.
IPv6 routing is enabled by default on Cisco routers.
__________________________________________________________________
11
Launch PTHide and Save PT
Open the PT Activity. Perform the tasks in the activity instructions and then
complete the task.
Which message is displayed on the website?
Correct!
Configured Correctly!
Good Job!
Well Done!*
__________________________________________________________________
12
Static routing typically uses less network bandwidth and fewer CPU operations
than dynamic routing does.*
Configuration of static routes is error-free.
Static routing does not advertise over the network, thus providing better security.*
The path a static route uses to send data is known.*
Static routes scale well as the network grows.
No intervention is required to maintain changing route information.
__________________________________________________________________
15
In an OSPFv2 configuration, what is the effect of entering the command network
192.168.1.1 0.0.0.0 area 0?
It tells the router which interface to turn on for the OSPF routing process.*
It changes the router ID of the router to 192.168.1.1.
It allows all 192.168.1.0 networks to be advertised.
It enables OSPF on all interfaces on the router.
__________________________________________________________________
16
Which statement describes a route that has been learned dynamically?
It is automatically updated and maintained by routing protocols.*
It has an administrative distance of 1.
It is unaffected by changes in the topology of the network.
It is identified by the prefix C in the routing table.
__________________________________________________________________
17
Which two factors are important when deciding which interior gateway routing
protocol to use? (Choose two.)
the autonomous system that is used
ISP selection
Scalability*
campus backbone architecture
speed of convergence*
__________________________________________________________________
18
Which three statements are advantages of using automatic summarization?
(Choose three.)
It improves reachability in discontiguous networks.
It ensures that traffic for multiple subnets uses one path through the internetwork.*
It decreases the number of entries in the routing table.*
It reduces the frequency of routing updates.*
It increases the size of routing updates.
It maximizes the number of routes in the routing table.
__________________________________________________________________
19
Refer to the exhibit. Which two conclusions can be derived from the output?
(Choose two.)
There is one feasible successor to network 192.168.1.8/30.*
The network 192.168.10.8/30 can be reached through 192.168.11.1.*
The neighbor 172.16.6.1 meets the feasibility condition to reach the 192.168.1.0/24
network.
Router R1 has two successors to the 172.16.3.0/24 network.
The reported distance to network 192.168.1.0/24 is 41024256.
__________________________________________________________________
20
Refer to the exhibit. Which of the three Cisco IOS images shown will load into
RAM?
The router selects an image depending on the value of the configuration register.*
The router selects an image depending on the boot system command in the
configuration.
The router selects the third Cisco IOS image because it contains the advipservicesk9
image.
The router selects the third Cisco IOS image because it is the most recent IOS image.
The router selects the second Cisco IOS image because it is the smallest IOS image.
__________________________________________________________________
21
Drag and drop
__________________________________________________________________
22
Refer to the exhibit. Which two configurations would be used to create and apply a
standard access list on R1, so that only the 10.0.70.0/25 network devices are
allowed to access the internal database server? (Choose two.)
R1(config)# access-list 5 permit 10.0.70.0 0.0.0.127*****
R1(config)# interface GigabitEthernet0/0
R1(config-if)# ip access-group 5 out******
R1(config)# access-list 5 permit 10.0.54.0 0.0.1.255
R1(config)# access-list 5 permit any
R1(config)# interface Serial0/0/0
R1(config-if)# ip access-group 5 in
__________________________________________________________________
23
31
Refer to the exhibit. An administrator has entered the command defaultinformation originate in OSPFv3 global configuration mode on R1, but R2 is not
receiving a default route. What is the problem?
R1 does not have a default route configured.*
The default-information originate command is only used for OSPFv2.
R1 and R2 are on different subnets.
OSPFv3 is not running on R2.
__________________________________________________________________
32
Which three requirements are necessary for two OSPFv2 routers to form an
adjacency? (Choose three.)
The two routers must include the inter-router link network in an OSPFv2 network
command.*
The OSPF hello or dead timers on each router must match.*
The OSPFv2 process ID must be the same on each router.
The link interface on each router must be configured with a link-local address.
The OSPFv2 process is enabled on the interface by entering the ospf process area-id
command.
The link interface subnet masks must match.*
__________________________________________________________________
33
Refer to the exhibit. What two types of devices are connected to R1? (Choose two.)
Hub
Repeater
Switch*
Source Route Bridge
Router*
__________________________________________________________________
34
What type of static route is created when the next-hop IP address and exit interface
are specified?
recursive static route
floating static route
directly connected static route
fully specified static route*
__________________________________________________________________
35
What is the reason for a network engineer to alter the default reference bandwidth
parameter when configuring OSPF?
to increase the speed of the link
to more accurately reflect the cost of links greater than 100 Mb/s*
to enable the link for OSPF routing
to force that specific link to be used in the destination route
__________________________________________________________________
36
Refer to the exhibit. Which command will properly configure an IPv6 static route on
R2 that will allow traffic from PC2 to reach PC1 without any recursive lookups by
router R2?
R2(config)# ipv6 route 2001:db8:10:12::/64 S0/0/0*
R2(config)# ipv6 route 2001:db8:10:12::/64 2001:db8:32::1
R2(config)# ipv6 route ::/0 2001:db8:32::1
R2(config)# ipv6 route 2001:db8:10:12::/64 S0/0/1
__________________________________________________________________
37
39
41
Refer to the exhibit. R1 was configured with the static route command ip route
209.165.200.224 255.255.255.224 S0/0/0 and consequently users on network
172.16.0.0/16 are unable to reach resources on the Internet. How should this static
route be changed to allow user traffic from the LAN to reach the Internet?
Change the exit interface to S0/0/1.
Change the destination network and mask to 0.0.0.0 0.0.0.0.0.*
Add the next-hop neighbor address of 209.165.200.226.
Add an administrative distance of 254.
__________________________________________________________________
42
Refer to the exhibit. A company has migrated from single area OSPF to multiarea.
However, none of the users from network 192.168.1.0/24 in the new area can be
reached by anyone in the Branch1 office. From the output in the exhibit, what is the
problem?
The router has not established any adjacencies with other OSPF routers.
The OSPF routing process is inactive.
There are no interarea routes in the routing table for network 192.168.1.0.*
The link to the new area is down.
__________________________________________________________________
43
Which two OSPFv3 statements are true? (Choose two.)
The router ID is configured using an IPv4 address.*
The router ospf priority priority command is issued under the router configuration mode.
The router-id router-id command is issued in interface configuration mode.
The multicast address FF02::6 is used to forward packets to the OSPF DR and
BDR.*
OSPF networks are configured under router configuration mode.
__________________________________________________________________
44
45
46
57
192.168.25.18.
An SSH connection is allowed from a workstation with IP 192.168.25.18 to a device
with IP 172.16.45.16.*
A Telnet connection is allowed from a workstation with IP 172.16.45.16 to a device with
IP 192.168.25.18.
__________________________________________________________________
58
Refer to the exhibit. What are two things that are different about the highlighted E2
routes in the routing table? (Choose two.)
These routes were learned using Type 5 LSAs.*
These routes are networks contained to other routers in a different OSPF area.
These routes can be used as backup default routes.
These routes are used to reach networks outside the OSPF multiarea network.*
These routes have an administrative distance of 20.
These routes are networks connected to other routers in the same OSPF area.
__________________________________________________________________
59
Which statement describes a characteristic of standard IPv4 ACLs?
They can be created with a number but not with a name.
They are configured in the interface configuration mode.
They filter traffic based on source IP addresses only.*
They can be configured to filter traffic based on both source IP addresses and source
ports.
__________________________________________________________________
60
Which three addresses are EIGRP multicast addresses? (Choose three.)
224.0.0.10*
224.0.0.9
01-00-5E-00-00-0A*
01-00-5E-00-00-10
FF02::9
FF02::A*