(il moore
INDUSTRIES
April 1995
Description
Moore Industries’ PDC DC Voltage Transducer and
Ground Fault Detector simultaneously monitors both
voltage level and ground faults in a floating battery
system. The PDC eliminates the need for separate
devices to perform these very important functions.
The POC accepts a de input from a battery. It
accurately converts the input to a proportional
current (0-1mA or 4-20mA) signal output ready for
interface with a readout device or a SCADA system.
While monitoring power usage, the PDC continu-
ously checks the battery system for leakage to
ground. Battery leakage can quickly render a
system useless, and also present a safety hazard
When a fault is detected, the PDC outputs @ contact
closure signal that activates a light, buzzer or similar
warning device.
For applications not requiring dual monitoring,
single-unction POC’s are also available. The PD
Configuration performs only as a de voltage trans.
ducer, while the PG configuration acts only as a
ground fault detector.
Easy Installation and Maintenance—A\l Moore
Industries power transducers are enclosed in rugged
and rustproof extruded aluminum housings that
provide superior heat dissipation. Keyhole cutout
screw holes allow installation and removal by loosen-
ing the mounting screws,
All circuitry is attached to the PDC’s front panel
to allow quick access to the circuitry without remov-
ing the entire housing. The circuit boards slide
smoothly out of the housing on PC board guides that
run the entire length inside the unit's housing.
Ordering Information
To order, use the bold face data from the Ordering
Specifications table. For assistance, refer to the
model number example located at the bottom of the
table
DC Voltage Transducer
and Ground Fault Detector
Unique keyhole-siotted mounting flanges alow the POC
fo be removed and re-installed by loosening the mounting
Features
+ Combination power monitor and alarm trip.
(One compact PDC continuously monitors battery
drain, and provides an alarm trip output when
a ground fault is detected
+ £0.2% of reading accuracy. The PDC is the
perfect choice when precise power monitoring is
demanded
+ Works with any battery type. Models aro
available that accommodate all common battery
voltages (24 to 600Vdic) and ground short
sensitivities (5 to 300K ohms).
+ Self-powered option. The PDC can be powered
by the battery source (-SP option) to eliminate the
need for an additional dedicated power supply.
+ Stable in outdoor environments. Ambient
temperature effect on the PDC is typically only
+£0.01%/°C over a -20°C to +70°C
‘operating range.DC Voltage Transducer
and Ground Fault Detector
Specifications
Performance Accuracy @25°C=2°C: | Performance Contact Rating (ground | Adjustments ‘Trip Point (models with
0.2% o1eacing, 201% | (Continued) fault alarm output): 12 | (continued) ground foul detector
ott seue ‘aise Br eon Siem utp Adan
ile i fora aK oe
WS Wn max, ben Se Savec, PF. «08 en
meee ‘tt oovcpesane rokoner
as, CE one
ores eee anaish tisapsl- arco irre (Si title
ee etn | cian tee heron
cororesdin Cra Ettect 001% ikeateetaet a
for SP sol-powered unt maximum for de crema ay ah. 8
Goose nea ean PARC Soo
Son pel oromarian Sa ed
tes 12 xunsoue Srnemee ee
Deets Tots Soa semen
frereimrase(unat | Adusments span: 210% oe oa
PD configuration ony) am ‘output using external ‘Alarm Trip Reset:
Response Time: To 0%. muttitum potentiometer ‘Momentary push of front
voor a, tne orca tanieas psi fore
Sirge Whatand ina moa tain eee a
capi: petoione eee Pa haha tak
Recon 174 (EEE iat wren
(472) BEAMA 219 — -
LED remains on unt
‘Alarm Trp Resat button on
front panelis pushed
‘Special SKV, O6KV BIL
(basic nsulaton lev)
‘Output Configuration Options Housings
POC | Norn InputSpans: | O4MA into BG Combination dc Power Supply Option ‘SM Surlace-
24D¢ 0-s0vee 15.000 hms | volage transducer and | (selecuon of one's required). | mount housing
4806 o-savec 4-20MA into 750 | ground faut detector | SP Sol-powered (available | DM DIN-ai
1250¢ 0-150vde corms. PD Single function de | only wih 48V ana 125V input | mount housing
2500€ 0-s00va- Ce Contact —_| vatiage transaucer type) note inpuvoutput
6000C 0-750Vde Closure (required | PG Single funcin ralationship
Cutput or models | ground faut detector only | -120AC, = 10%
Input Soans with wth PG BA0AC, = 10%
EXP Option: configuration
24DE 15-20Vee Non Required Options:
‘480¢ 30-60V0c “CG Case ground terminal
12506 75-1500 ER Energized relay (elay is
2500 150-300Vee energizes in the non-alarm
{6000 275-750Vee ‘condition ans de-ererg.2e0 in
the alarm eandiion to provide
Input Spans wih SP false fault detection)
Option “EXP Expanded scale input
ADC not available (te inputoutpatrelaionshi)
48DC s0-60Ve0 LR Lacing eiay (olay
42506 75-1500 ‘remains energized ntl faut is
25006 not avaiibie Ccomected and reset buon is,
{600DC not avaiiabie ‘aepressad)
-NC Normally closed relay in
NOTE: Input Spans place of standard normally
correspond to 0-100% ‘open relay
of analog output
‘When ordering, specify: Uni / Input / Output / Configuration / Power Option (equred), Options [Housing}
“Model Number Example: PDC / 2100 /0-IMA/ 0G /-1208C -LA [SM]PDC
DC Voltage Transducer
and Ground Fault Detector
FLOATING
Barren
SvsTEM
ee | —_A—»| so
+ f}__+| San,
zona
b rs (Proprinal io Batery
~ ‘Voltage Level)
\ negate Baty Compare
Lsatage to Ground Creat oie
No pe |
Atara
onactClsure | INDICATION
ft (Alarming Negative
Fat Conduen
Ac POWER SUPPLY
‘Figure 1. The POC detects both positive and negative ground faults. In this ilustraton, the PDC ie waming ofa negative ground fault
while sinutanecusly ransmiting 3 4.20mA signal proportional to battery dain.
Combination Monitor and
Ground Fault Detector
The POC (DG configuration) simultaneously monitors
power usage and detects ground faults.
Monitor Battery Voltage Level
The POC continually tracks the amount of power
being consumed by a battery-powered device or
system. It accepts @ de input from a battery, and
converts it to @ proportional current (O-1mA or
4-20mA) signal output ready for interface with a
readout device or SCADA systern. NOTE: With the
-EXP of -SP option, the input-to-output relationship is
different than standard (e.g., with the 125DC input
type, a 75Vde input will equal a 4mA output).
Ground Fault Detector
‘The PDC detects leakage to ground in a floating
battery back-up system. Ground faults can drain
away energy and render the system useless. They
can sometimes present a safety hazard as well
‘When the PDC senses momentary ground shorts
of between 5 and 300K ohms (user-selectable), it
outputs a contact closure signal for as long as the
Condition exists. The signal can be used to call
attention to the fault condition via an annunciator
Peanel ight, buzzer or other on/off device. Two LEDs
€n the unit's front panel indicate whether the fault is
positive or negative. The LED lit by the fault condi-
tion will remain on until reset by a manual push
button located on the unit's front panel.
Detects Positive and Negative Faults—The
POC continuously compares the amount of current
flowing between the positive terminal and ground,
‘and the negative terminal and ground. Under normal
‘operating conditions, these values would be equal.
However, if the POC senses a difference between the
two values, power is leaking to ground. The PDC
transmits its constant contact closure signal to call
attention to the ground fault. Figure 1 illustrates
detection of a negative ground fault.PDC
DC Voltage Transducer
and Ground Fault Detector
-+———"‘ssim
12027
eo —_ 163m
ee teary
‘ion —— ane
‘ion
irsem
3
Figure 2 instataton Dimensions
auios c= coNTACT quite a
Curur —neur CLOSURE EXTERNAL woop TERNAL
oe = OUTPUT POWER. a pO
| Wen ene if ! Lo yal sph ia
DG Contiguration PD Configuration
(GROUND REFERENCE
covract
ojejeiajajolok
Figure 3. Terminal Designations
The Interface Solution Experts + www.miinet.com ————_—_
Balun. nloecrcind China sles @moorend com.cn
OA@-FAKOS440.1797 Tl: 66-21-6806724- PAX: 0621 0629595
Untied States inominet.com
MOORE vw: cisjsstrisFicerjesrae6 to:
‘Ausaia- sales@mocrsind comau The Netherlands. sales@mooreinddemon.nl United Kingdom sales@moorelnd.com
i(BASH7ETY «FAK: (OG4ETSH20 Te: 01209 514488 - FAX: 01200596052
INDUSTRIES rete eisai 0205