Beruflich Dokumente
Kultur Dokumente
Website:http://biz.LGservice.com
COLOR MONITOR
SERVICE MANUAL
CHASSIS NO. : LM62C
MODEL:
L206WU(L206WU-WFS.A**MAP)
(
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS
SPECIFICATIONS ................................................... 2
ADJUSTMENT ...................................................... 13
PRECAUTIONS ....................................................... 4
EXPLODED VIEW...................................................24
SPECIFICATIONS
1. LCD CHARACTERISTICS
Type
: TFT Color LCD Module
Active Display Area : 20.1 inch diagonal
Pixel Pitch
: 0.258 (H) x 0.258 (V)
Size
: 459.4(H) x 296.4(V) x 16.5(D)
Color Depth
: 16.7M color
Electrical Interface
: LVDS
Surface Treatment
: Anti-Glare, Hard Coating(3H)
Operating Mode
: Normally White,Transmissive mode
Backlight Unit
: 4 CCFL
5. POWER SUPPLY
5-1. Power Adaptor(Built-in Power)
Input : AC 100-240V~, 50/60Hz, 1.2A
5-2. Power Consumption
MODE
2. OPTICAL CHARACTERISTICS
2-1. Viewing Angle by Contrast Ratio 5
Left : -70 min., -80(Typ) Right : +70 min., +80(Typ)
Top :+60 min., +75(Typ) Bottom : -70 min., -85(Typ)
2-2. Luminance
: 210(min)
(Full white pattern,0.70V)-6500K
: 450(min), 700(Typ)
DFC -> 5000 : 1(Typ)
POWER ON (NORMAL)
ON/ON
ACTIVE
STAND BY
OFF/ON
OFF
less than 2 W
AMBER
SUSPEND
ON/OFF
OFF
less than 2 W
AMBER
DPMS OFF
OFF/OFF
OFF
less than 2 W
AMBER
less than 2 W
OFF
BLUE
6. ENVIRONMENT
6-1. Operating Temperature : 10C~35C (50F~95F)
6-2. Relative Humidity
: 10%~80% (Non-condensing)
6-3. MTBF
: 50,000 HRS with 90%
Confidence level
Lamp Life
: 50,000 Hours (Min)
7. DIMENSIONS (with TILT/SWIVEL)
Width
Depth
Height
: R, G, B Analog
: 0~0.7 V
: 75
: 471 mm (18.54'')
: 271.1 mm (10.67'')
: 420 mm (16.54'')
: 30 ~ 83kHz
: 56 ~ 75Hz
: 1680 x 1050@60Hz
: 1680 x 1050@60Hz
Net. Weight
Gross Weight
-2-
1
9
17
8
16
24
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal (DVI-D)
T. M. D. S. Data2T. M. D. S. Data2+
T. M. D. S. Data2/4 Shield
T. M. D. S. Data4T. M. D. S. Data4+
DDC Clock
DDC Data
Analog Vertical Sync.
T. M. D. S. Data1T. M. D. S. Data1+
T. M. D. S. Data1/3 Shield
T. M. D. S. Data3T. M. D. S. Data3+
+5V Power
Ground (return for +5V,
Pin
16
17
18
19
20
21
22
23
24
Signal (DVI-D)
Hot Plug Detect
T. M. D. S. Data0T. M. D. S. Data0+
T. M. D. S. Data0/5 Shield
T. M. D. S. Data5T. M. D. S. Data5+
T. M. D. S. Clock Shield
T. M. D. S. Clock+
T. M. D. S. Clock-
-3-
PRECAUTION
WARNING FOR THE SAFETY-RELATED COMPONENT.
WARNING
To Instrument's
exposed
METALLIC PARTS
1.5 Kohm/10W
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.
-4-
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this
service manual and its supplements and addenda, read
and follow the SAFETY PRECAUTIONS on page 3 of this
publication.
NOTE: If unforeseen circumstances create conflict
between the following servicing precautions and any of the
safety precautions on page 3 of this publication, always
follow the safety precautions. Remember: Safety First.
General Servicing Precautions
1. Always unplug the receiver AC power cord from the AC
power source before;
a. Removing or reinstalling any component, circuit
board module or any other receiver assembly.
b. Disconnecting or reconnecting any receiver electrical
plug or other electrical connection.
c. Connecting a test substitute in parallel with an
electrolytic capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect
polarity installation of electrolytic capacitors may
result in an explosion hazard.
d. Discharging the picture tube anode.
2. Test high voltage only by measuring it with an
appropriate high voltage meter or other voltage
measuring device (DVM, FETVOM, etc) equipped with
a suitable high voltage probe.
Do not test high voltage by "drawing an arc".
3. Discharge the picture tube anode only by (a) first
connecting one end of an insulated clip lead to the
degaussing or kine aquadag grounding system shield
at the point where the picture tube socket ground lead
is connected, and then (b) touch the other end of the
insulated clip lead to the picture tube anode button,
using an insulating handle to avoid personal contact
with high voltage.
4. Do not spray chemicals on or near this receiver or any
of its assemblies.
5. Unless specified otherwise in this service manual,
clean electrical contacts only by applying the following
mixture to the contacts with a pipe cleaner, cottontipped stick or comparable non-abrasive applicator;
10% (by volume) Acetone and 90% (by volume)
isopropyl alcohol (90%-99% strength)
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual,
lubrication of contacts in not required.
6. Do not defeat any plug/socket B+ voltage interlocks
with which receivers covered by this service manual
might be equipped.
7. Do not apply AC power to this instrument and/or any of
its electrical assemblies unless all solid-state device
heat sinks are correctly installed.
8. Always connect the test receiver ground lead to the
receiver chassis ground before connecting the test
receiver positive lead.
Always remove the test receiver ground lead last.
-5-
Replacement
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad
and solder it.
3. Clean the soldered areas with a small wire-bristle
brush. (It is not necessary to reapply acrylic coating to
the areas).
"Small-Signal" Discrete Transistor
Removal/Replacement
1. Remove the defective transistor by clipping its leads as
close as possible to the component body.
2. Bend into a "U" shape the end of each of three leads
remaining on the circuit board.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the
corresponding leads extending from the circuit board
and crimp the "U" with long nose pliers to insure metal
to metal contact then solder each connection.
Power Output, Transistor Device
Removal/Replacement
1. Heat and remove all solder from around the transistor
leads.
2. Remove the heat sink mounting screw (if so equipped).
3. Carefully remove the transistor from the heat sink of the
circuit board.
4. Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6. Replace heat sink.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close
as possible to diode body.
2. Bend the two remaining leads perpendicular y to the
circuit board.
3. Observing diode polarity, wrap each lead of the new
diode around the corresponding lead on the circuit
board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder
joints of the two "original" leads. If they are not shiny,
reheat them and if necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board
hollow stake.
2. Securely crimp the leads of replacement component
around notch at stake top.
3. Solder the connections.
CAUTION: Maintain original spacing between the
replaced component and adjacent components and the
circuit board to prevent excessive component
temperatures.
-6-
At Other Connections
Use the following technique to repair the defective copper
pattern at connections other than IC Pins. This technique
involves the installation of a jumper wire on the
component side of the circuit board.
1. Remove the defective copper pattern with a sharp
knife.
Remove at least 1/4 inch of copper, to ensure that a
hazardous condition will not exist if the jumper wire
opens.
2. Trace along the copper pattern from both sides of the
pattern break and locate the nearest component that is
directly connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead
of the nearest component on one side of the pattern
break to the lead of the nearest component on the
other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is
dressed so the it does not touch components or sharp
edges.
-7-
TIMING CHART
VIDEO
A
E
D
SYNC
C
Sync
Polarity
Dot
Clock
Frequency
H(Pixels)
28.321
31.468
Total
Period
(E)
900
V(Lines)
70.08
449
MODE
H/V
1
2
H(Pixels)
V(Lines)
H(Pixels)
V(Lines)
H(Pixels)
V(Lines)
H(Pixels)
V(Lines)
H(Pixels)
V(Lines)
H(Pixels)
V(Lines)
H(Pixels)
+/-
V(Lines)
+/-
H(Pixels)
V(Lines)
10
11
12
H(Pixels)
V(Lines)
H(Pixels)
V(Lines)
H(Pixels)
V(Lines)
25.175
Front
Porch
(C)
108
Blanking
Time
(B)
54
12
35
Sync
Video
Duration
Active
(D)
Time ( A )
720
18
400
31.469
800
640
16
96
48
59.94
525
480
10
33
31.5
37.5
840
640
16
64
120
75
500
480
16
40.0
37.879
1056
800
40
128
88
60.317
628
600
23
49.5
46.875
1056
800
16
80
160
75.0
625
600
21
65.0
48.363
1344
1024
24
136
160
60.0
806
768
29
78.75
60.123
1312
1024
16
96
176
108.0
108.0
135.0
119
146.25
75.029
800
768
28
67.500
1600
1152
64
128
256
75.000
900
864
32
63.981
1688
1280
48
112
248
60.02
1066
1024
38
79.976
1688
1280
16
144
248
75.035
1066
1024
38
64.674
1840
1680
48
32
80
59.883
1080
1050
21
65.290
2240
1680
104
176
280
59.954
1089
1050
30
-8-
Resolution
720 X 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1680x1050
1680x1050
DISASSEMBLY-Set
#2
#1
#4
#3
#5
#6
-9-
D-Sub
DVI-D
USB UP
- 10 -
USB
DN(X2)
Crystal
12MHz
DVI
(TMDS)
1.8 V
3.3 V
SIL1160
Nand Flash
(64MB)
DL-160
USB HUB
USB2504
SMI321
Controller
Crystal
24MHz
USB
(TMDS)
Switch
Crystal
24MHz
EEPROM
(EDID)
DVI(TMDS)
EEPROM
(EDID)
1.8 V
3.3 V
Regulator
EEPROM
(System)
SDA
/SCL
Dual
Interface
Engine
5V
MCU
LVDS
Panel
Interface
Filter
3.3V
Flash ROM
Clock
Generator
DRAM
Response
Time
Enhancement
14.318MHz
Crystal
OSD
Display
Processing
Engine
3.3 V
TSUMO5 8 CWHJ
15V
15 V
5V
LIPS
Vcc
5V
LVDS
140Mhz
Module
KEY
Analog (R/G/B)
BLOCK DIAGRAM
- 11 -
15V
50 ~ 60Hz
EMI
COMPONENTS
INPUT RECTIFIER
AND FILTER
HVDC
ENERGY
TRANSFER
100KHz
OUTPUT RECTIFIER
AND FILTER
5V
GND
LINE
100 ~ 240V
PHOTOCOUPLER
ISOLATION
PWM
CONTROL
CIRCUIT
PRIMARY
SIGNAL
Collection
and
Feedback
SECONDARY
Operation description_Power
1. EMI components.
This part contains of EMI components to comply with global marketing EMI standards like FCC,VCCI CISPR, the
circuit included a line-filter, across line capacitor and of course the primary protection fuse.
2. Input rectifier and filter.
This part function is for transfer the input AC voltage to a DC voltage through a bridge rectifier and a bulk capacitor.
3. Energy Transfer.
This part function is for transfer the primary energy to secondary through a power transformer.
4. Output rectifier and filter.
This part function is to make a pulse width modulation control and to provide the driver signal to power switch, to
adjust the duty cycle during different AC input and output loading condition to achieve the dc output stabilized, and
also the over power protection is also monitor by this part.
5. Photo-Coupler isolation.
This part function is to feed back the DC output changing status through a photo transistor to primary controller to
achieve the stabilized DC output voltage.
6. Signal collection.
This part function is to collect the any change from the DC output and feed back to the primary through photo
transistor.
- 12 -
ADJUSTMENT
Windows EDID V1.0 User Manual
- 13 -
SERVICE OSD
1) Turn off the power switch at the right side of the display.
2) Wait for about 5 seconds and press MENU, POWER switch for 1 second interval.
3) The SVC OSD menu contains additional menus that the User OSD menu as described below.
a) CLEAR ETI : To initialize using time.
c) Auto Color : W/B balance and Automatically sets the gain and offset value.
(press key for over 3 sec)
d) AGING : Select Aging mode(on/off).
b) Module : To select applied module.
d) NVRAM INIT : EEPROM initialize.(24C16, press key for over 3 sec)
e) R/G/B-9300K : Allows you to set the R/G/B-9300K value manually.
f) R/G/B-6500K : Allows you to set the R/G/B-6500K value manually.
g) R/G/B-Offset : Allows you to set the R/G/B-Offset value manually.(Analog Only)
h) R/G/B-Gain : Allows you to set the R/G/B-Gain value manually.(Analog Only)
A
9
IBM
Compatible PC
Video Signal
Generator
15
10
5
d
tu
se
RS
23
2C
No
C
13
25
PA
RA
LL
EL
OFF
14
ON
F
Power inlet (required)
5V
220
PO
WE
R
VG
S
MO
NI
TO
R
V-S
YN
CS
T
Control Line
PARALLEL PORT
5V
11
6
1
ON
4.7K
4.7K
5V
E
4.7K
OFF
74LS06
74LS06
E ST Switch
B
F V-Sync On/Off Switch
(Switch must be ON.)
- 14 -
TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER
(POWER INDICATOR OFF)
NO
YES
2
3
1
IS IC302 PIN2(1.8V)
IC301 PIN2(3.3V)
NO
CHECK IC702(1.8V)
IC703(3.3V) LINE
YES
4
1
NO
CHECK CRYSTAL(X501)
YES
CHECK IC200
Waveforms
1
P703-#5,6
IC302-#2
- 15 -
IC301-#2
X200-#201
NO RASTER
(OSD IS NOT DISPLAYED)
CHECK P703
VOLTAGE PIN5,6
(5V)?
NO
YES
NO
2
YES
1. CONFIRM BRIGHTNESS
OSD CONTRL STATUS
2. CHECK SCALER DIM ADJ
PORT
3. CHECK SCALER LAMP
ADJ PORT
NO
CHECK P703
PIN11
YES
CHECK
PULSE AS
CONTACTING PROBE
TO THE LAMP
WIRE OF THE
LCD MODULE
NO
POWER BOARD (LIPS)
Waveforms
YES
1
P703-#5,6
P703-#9
P703-#10 (Brightness 0)
LAMP CURRENT
- 16 -
NO RASTER
(OSD IS NOT DISPLAYED)
CHECK IC200
PIN8,14,20(3.3V)
PIN21,104(1.8V)
NO
CHECK IC702(1.8V),
IC703(3.3V)
YES
IC200
PIN 127,128
14.3MHZ?
NO
YES
CHECK IC200
PIN32(H-SYNC) AND
PIN33(V-SYNC).
IS PULSE APPEARED AT
SIGNAL PINS?
NO
YES
TROUBLE IN CABLE
OR LCD MODULE
Waveforms
1
U502-#201
- 17 -
4. TROUBLE IN DPM
TROUBLE IN DPM
NO
CHECK PC
PC IS GOING
INTO DPM MODE
YES
1
2
CHECK
IC200 PIN 32,33
SYNC PULSE
NO
CHECK H/V SYNC LINE
YES
TROUBLE IN IC502
Waveforms
1
H-SYNC
V-SYNC
- 18 -
IC606 P1 (5V_USB)=5V
YES
IC606 P3
(VUSB3-3V)=3V
NO
CHECK IC606
YES
NO
IC602 P52
CHECK PC
YES
NO
X601=24Mhz
CHECK X601
YES
NO
CHECK IC602
IC602 P8,P9
YES
- 19 -
*IC601
(Microcontrollers)
IC601 P48=5V
(5V_USB)
NO
CHECK IC300
YES
IC601 P45=1.8V
P47=3.3V
NO
CHECK IC601
YES
NO
X500=12Mhz
CHECK X500
YES
IC601 P3
(NANWP)
NO
CHECK IC601
YES
*IC505
(NAND Flash memory)
NO
CHECK PROGRAM WIRTE
IC605 P12,P37=3.3V
- 20 -
6. USB NO RASTER
IC606 P1 (5V_USB)=5V
YES
IC606 P3
(VUSB3-3V)=3.3V
NO
CHECK IC606
YES
NO
IC602 P52
CHECK PC
YES
NO
X601=24Mhz
CHECK X601
YES
NO
CHECK IC602
IC602 P5,P6
YES
- 21 -
*IC504
(Video processors_display link
USB =>TLL)
IC303_3.3V
IC304_2.5V
IC305_1.8V
NO
CHECK IC303,304,305
YES
NO
X500=24Mhz
CHECK X500
YES
IC502 P77(HSYNC)
P78(VSYNC)
NO
CHECK IC504
YES
*IC502(Silicon image)
TLL=>TMDS
IC502 P34(2RXC-)
P35(2RXC+)
NO
CHECK IC502
YES
*IC702(Analog
switch)
IC301=3.3V
IC306=1.5V
NO
CHECK IC301,306
YES
NO
CHECK IC702
IC702 P18(PXC-)
YES
- 22 -
*IC200<SCALOR>
TMDS,RGB=>LVDS
NO
CHECK IC302
IC302=1.8V
YES
NO
CHECK X200
X200=14.3Mhz
YES
NO
CHECK IC200
P704 P20
YES
NO
DRIVER SET UP
YES
CHECK PANEL
- 23 -
520
310
320
330
300
200
510
440
500
LV1
430
420
410
400
910
900
920
930
EXPLODED VIEW
- 24 -
MAIN (BOTTOM)
- 32 -
CONTROL
- 33 -
SCHEMATIC DIAGRAM
1. SCALER
- 34 -
2. USB DISPLAY
- 35 -
- 36 -
4. WAFER
- 37 -
- 38 -
P/NO : MFL36713676
Jun. 2007
Printed in Korea