| How to Install Valve & Caution to Take
1.Make sure that you instal strainer infront of differential pressure control
valve to prevent contaminant from getting into the valve
2.Maintain sufficient distance between valves to avoid water turbulence
3. Install By-Pass Line for maintenance and management
4.Check the arrow direction of valve body so that its installed the same
direction as water flow.
5. Install pressure pipe in the front side (return pipe) or the backside (supply
pipe) of ferential pressure control valve with more than 5 times of distance
of pipe diameter
6. Attach ball valve to connection of pressure pipe and lock it
7 Install supply pressure pipe atthe top of dlaphragm case and return pressure
pipe at the bottom
£8, Close manual valve atthe front and back of differential pressure control
valve and open bypass valve. Conduct freshing several times
‘9. After freshing, close bypass valve and slowly open manual valve
10. Slowly open ball valve of supply and return pressure pipe atthe same
time. Open drain valve attached tothe top and bottom of diaphragm case,
and close the top valve first and then the bottom valve when water is
drained out
11, Check operation and differential pressure. Start to use if they fine.
you supply water with only one vale of pressure pipe ope. it canimpose heavy
oad on diaphragm and ether parts So make sure you open both return ball vale
and supply ball valveo pressure pipe
[ How to Install Valve & Caution to Take
{not requested otherwise, ferential pressure i set at CO7MPa
when delivered
2. fyou want to adjust differential pressure to respond to changed,
conditions foliow the steps illustrated below.
‘a. 0pen all valves inside circulation piping and operate pump. Read
the differential pressure of supply and return,
Loosen the bolt (Smm) placed on spring head.
«Spin the nut dockwise or counterclockwise while looking at supply
and return pressure to set the differential pressure you want.
Lock the bolt (Smm) after setting the differential pressure to
prevent arbitrary adjustment by others.
SESE ET
Make suretoflly comprehend the flowing caution inhaling the product so that
product may display it performance.
".Donot apply impact ont
2Avoid any place with ust or humid when storing it
3,A speci attention should be pad so that any impurtis are ntinseted int the
product
«4When attaching tonto a pipe the location shoul be fee of and or debris while
‘point of gske should be ao cleaned up
Sit should be installed on place easy to access for epaie
The structure, dimensions and materials may by changed without any prior notice for
theimprovement of performance
o Manda
Topi seat cen
song
Top sate
Dtragm ase soins
Daag Pte cent
Daprogm
Busing st ae
ieee Daptrogn cae
York Canesten
Stuting Box racing et
Toptange lockout
> cone
sea
Sor
body| How 8 Fix problems in Differential
pressure Control Valve Operation
Problem Cause
Pressure pipe bal valve
islocked
Pressure pipe isnot
propery laid
Pressure pipe is clogged
Valve does
NotOperate | Valves installed ina
wrong direction
Diaphragm is damaged
Differential pressure does
not decrease even after
loosening adjusting nut
Differential
Solution
Slowly open the valve
ater Checking
See How to Install Valve
Re-install after checking
the arrow
Reinstall the Valve
Diaphragm is damaged
ifindieator does not work
when draining out water
through supply air pin
‘with supply ball valve
closed and return ball
valve open.
pressure ishigh
orlow
not rise even ater
‘Check diaphragm
Differential pressure does
fastening adjusting nut
[Maintenace Tips
1.Locking after checking gate valve
Main valve locking
2, Pressure pipe ball valve locking
3.Slonly loosening after checking
height ofthe spring specified
4. Separating the pressure pipe
5. Loosening after checking the
height of indicator’ stamp thread
6.Slowly loosening stuffing nut box
Stop disassembly if water
continuously flows
7.Checking and replacing the
packing and everselyasembiing
it
1. Checking and locking gate valve
2. Pressure pipe ball valve locking
3. Checking and slowly loosening
the height of spring specified
4. Separating the pressure pipe
5. Loosening after checking the
height of indicator’ stamp thread
6. Disassembling the actuator
Tits rusty excessively, it should
bbe ground with soft sand paper
8 Replace Oring and assembling it