Beruflich Dokumente
Kultur Dokumente
-Aviation Dictionary
59. SCR is
a) two junction diode
b) three junction diode
c) two junctions are forward biased, two ae reverse biased
d) all of the above
60. Mark the correct statement regarding reamer
a) it is made of high carbon steel or HSS
b) it roughens the drill hole to larger size
c) as in a + enlarge the drill hole to close tolerance and smoothness
d) all the above
61. Mark the correct statement, regarding check valve function
a) it directs fluid according to plan
b) it directs fluid in one direction unrestricted & unrestricted flow in either direction
c) inline type check valve used in the component to full flow in one direction
d) all of the above
62. Current from emitter to collector flows when
a) emitter base function is forward biased & base collector junction is reversed biased
b) emitter-base junction is reverse biased & collector base junction is forward biased
c) base collector is close
d) none
63. Mark correct statement regarding punch-9A 531
a) it is used to locate centre to be drilled
b) pin punch is a tapered type punch
c) another name for drift punch is drive punch
d) all the above
64. Files are -9A 536
a) annealed & tempered
b) made of high grade tool steel
c) hardened & tempered
65. Alodine is applied by
a) cladding
b) dipping
c) priming
d) as per manufactures diagonosis
66. For safe balance while jacking
a) weight added forward & rearward of fuselage
b) must not be jacked on single wheel
c) always jacked inside the hanger
d) all the above
67. Force acting around a charged body is (Aviation Dictionary)
a) electromagnetic field
b) electrostatic field
c) magneto motive field
d) induction field
68. Unit of magnetic flux is Aviation Dictionary
a) Weber ( also Maxwell)
b) weber / minimum
c) guage
d) test
PAPER-II (JUNE-2004)
1. Al-alloy rivet 2024 can be used:
a) Used on a/c immediately after heat-treatment
b)
c)
d)
2. Circular pitch (C.P.) of gears:
a) Distance between corresponding point on adjacent teeth at pitch circle
b)
c)
d)
3. Bottoming TAPS are used for:
a) To make thread properly at the bottom of holes & not tapered
b)
c)
d)
4. Hand held reamers have:
a) Straight & taper shank
b)
c)
d)
5. How angle of object measured:
a) Bevel protection & sine rule method
b) Bevel protection only
c) Bevel protection & cas Rules method
d) Bevel protection & since cas rule
6. How the gear teeth size measured:
a) Measured at the chord thickness where pitch circle crosses at points
b)
c)
d)
7. MTCS:
a) Ball peen hammer is used where bent is sharp
b)
c)
d)
8. Identify the bolt
a) Re-worked bolt
b)
c)
d)
9. Measure the reading 14 20:
a) 14 20
b) 20 11
c) 30 10
10. MTCS:
a) Bolt has right hand threads except in special cases
b)
c)
d)
10
11
21. 7 resister connected to 20 each in parallel voltage 2v ammeter connected across the circuit
measure:
a) 7/10 amp
b) 1/10 amp
c) 2/10 amp
d) 20/10 amp
22. Speed of light energy in 3 lakhs k.m & frequency is 100 Mhz, its wave length is:
a) 3 meters or 9.27 ft.
b)
c)
d)
23. Convert 296 into binary
a) 100101000
b)
c)
d)
24. To prevent corrosion Al. alloy sheets how they are stored:
a) Only the coat of linced/oil is sufficient
b) Use of plastic cover without oil coating
c) Use of oil coating in addition to plastic cover
25. What causes-de-lamination of composite layer:
a) In adequate application of heat on pressure during process
b)
c)
d)
26. How the composites are electrical bonding:
a) Al. metal is bonded to the composite to the adjacent metal to dissipate charges
b)
c)
d)
27. The triode grid purpose is:
a) Reduce space charge
b)
c)
d)
28. Zener diode acts as a voltage regulator:
a) To control the over voltage in transistorize voltage regulator
b)
c)
d)
29. When PN junction start conducting:
a) When the plate is more +ve than the cathode
b) When the cathode is more +ve than plate
c) When the cathode & plate is at same potential
30. P-N junction cannot used as:
a) Rectifier
b) Amplifier
c) Transistor
12
13
14
15
16
17
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
68.
69.
70.
71.
72.
73.
74.
75.
76.
77.
78.
79.
Laminated plastic
Acrylic plastic
Annealing
Working drawing
Power factor
Rms value
DIL
Matrix
Rivet drawing
Carbon over 3%
Battery has +ve & -ve terminals connected increases capacity & decreases internal resistance
Mag. Treatment
Al. boron have stable str. due to tight bonding
Resistance circuilt (numerical)
Resistance increases as temp. decreases
Motor back emf
Chisel is classified by width of cutting edges
Depth of thread
Swaging
Dye penetrant
Drill
Magnut when dropped through a coil
18