Beruflich Dokumente
Kultur Dokumente
w w w. g r a c e c o n s t r u c t i o n . c o m
Cl/SfB
Ln2
Bituthene 8000 HC
Applications
Description
Bituthene 8000 HC is a unique 1.5mm
thick flexible, preformed waterproof
membrane comprising a grey HDPE
composite film and a thick self-adhesive
rubber/bitumen compound. The specially
developed film is dimensionally stable
Servijoint One
Solarshield HC
Bituthene
8000 HC on
Primer B1
Details shown are typical illustrations only and not working drawings. For
assistance with working drawings and additional technical advice please
contact Grace Technical Services
85
Bituthene
1 m x 20 m roll
aligned and overlapped 50mm minimum There is no legal requirement for a
8000 HC
Weight 32 kg
at side and ends and well rolled with a
Material Safety Data Sheet for Bituthene
Palletisation
20 rolls per pallet
firm
pressure
using
a
Bituthene
Lap
8000 HC, Solarshield HC, Servipak
Storage
Store upright in dry
Roller to ensure complete adhesion and Protection Boards, or Lap Roller. For
conditions below 40C
continuity between the layers. In cool
Nominal
1.5mm
health and safety questions on these
conditions, the application of gentle
Thickness
products please contact Grace
heat between layers by hot air gun or
Construction Products Limited.
Ancillary Products
soft flame will assist in promoting
For Primer B1, Bituthene LM, Bituthene
See separate data sheets
adhesion at lap joints.
Mastic and Pak Adhesive read the
Primer B1
5 and 25 litre drums
Areas of apparent damage should be
product label and Material Safety Data
Coverage
10-12 sq metre per litre
checked and punctures or damaged
Sheet (MSDS) before use. Users must
depending on method
areas should be cleaned and patched
comply with all risk and safety phrases.
of application, surface
using Bituthene 8000 HC with 50mm
texture, porosity and
MSDSs can be obtained from Grace
laps all round.
ambient temperature
Construction Products or from our web
Bituthene LM
5.7 litre packs
Pipe entries may be sealed with
site at www.graceconstruction.com.
Bituthene Mastic 3 litre can
Bituthene LM extended over the
Lap Roller
Unit
adjacent flat slab area to give a
Specification
Ancillary Products
minimum 50mm lap with the Bituthene Bituthene 8000 HC preformed, solar
See separate data sheets
8000 HC. Bituthene LM is a two
reflective and damage indicative selfSolarshield HC
1 m x 16 m roll
component compound for
adhesive membrane shall be laid on to
Servipak
waterproofing irregular profiles in
smooth concrete substrates and on to
protection boards
conjunction with Bituthene systems. It
vertical surfaces primed with Primer B1,
Pak Adhesive
5 litre can
is supplied in 5.7 litre packs.Following
applying the preformed membrane sticky
Equipment by Others
the application and inspection care
side downwards, to give well rolled
should be taken to prevent damage by
Soft brush, Stanley knife, brush or roller
50mm overlaps, and shall be laid strictly
following trades. As soon as practicable
for priming. Stiff broom and airline for
in accordance with the manufacturers
after the application, Bituthene 8000 HC instructions and supplied by Grace
cleaning surface.
should be protected from exposure to the Construction Products Limited, Ajax
Installation
weather and physical damage using
Avenue, Slough, Berkshire,
insulation boards laid dry.
Measures should be taken to ensure that
SL1 4BH, United Kingdom.
all surfaces are free from ice, frost or
Tel: +44 (0)1753 692929.
condensation. Installation is
Fax: +44 (0)1753 691623.
Limitation
recommended between +4C and +55C. Bituthene 8000 HC is not intended for
Roof slabs should be surface dry, free
permanent exposure. Exposed areas of
from standing water, and laid to a
membrane at upstands etc, should be covered
regular surface free from sharp
with Solarshield HC or similar flashing.
protrusions and hollows.
Horizontal and vertical surfaces shall be
smooth, regular, dry and free from nails
and primed with one coat of Primer B1
applied by brush or roller at a rate of
10-12 sq m/litre depending on the
porosity of the surface, and allowed to
dry completely before the application of
the Bituthene 8000 HC (horizontal
surfaces under base slabs do not usually
require priming before applying the
membrane).
Bituthene 8000 HC shall be laid by
peeling back the protective release paper
and applying the adhesive face onto the
Comparsion of Solar Heat Gain Over Time On Exposed Membrane Samples
Supply
86