Beruflich Dokumente
Kultur Dokumente
DR-ENGP-1.1 R.3
E&P
CLIENT:
OWNER:
N:
PAGE:
of
AREA:
TITLE:
Piping Standard and Material for Oil Production and Process Facilities
VOLUME:
24
PART:
CHAPTER:
DR-ENGP-1.1-R.3
Note: For requisition of materials referred here in through their TAGs, the
Petrobras / E&P materials standardization PM-1/2, shall be used.
APPROVAL
VERIFICATION
EXECUTION
ENGP
IPP
EISA
CORPORATE INFORMATION
Approved
29/11/2010
INDEX
CORPORATE INFORMATION
CORPORATE INFORMATION
2 Reference Standards
STANDARD
TITLE
API RP 14E
API SPEC 5L
API SPEC 6D
ASME B1.1
ASME B1.20.1
ASME B16.1
ASME B16.5
ASME B16.9
ASME B16.11
ASME B16.20
Metallic gaskets for pipe flanges ring-joint, spiralwound, and jacketed addenda A-07/21/2000.
CORPORATE INFORMATION
STANDARD
TITLE
ASME 16.21
ASME B16.25
Buttwelding End.
ASME B16.28
ASME B16.47
ASME B18.2.2
ASME B31.3
Process Piping.
ASME B36.10
ASME B36.19
ASTM A105
ASTM A106
ASTM A123
ASTM A126
ASTM A182
Standard Specification for Forged or Rolled Alloy.Steel Pipe Flanges, Forged Fittings, and Valves
and Parts for High-Temperature Service.
ASTM A193
ASTM A194
ASTM A216
CORPORATE INFORMATION
STANDARD
TITLE
ASTM A234
ASTM A312
ASTM A320
ASTM A333
ASTM A350
ASTM A351
ASTM A352
ASTM A358
ASTM A403
ASTM A420
ASTM A487
CORPORATE INFORMATION
STANDARD
TITLE
ASTM A522
ASTM A536
ASTM A564
Standard Specification for Hot-Rolled and ColdFinished Age-Hardening Stainless Steel Bars and
Shapes.
ASTM A671
ASTM A694
ASTM A790
ASTM A815
ASTM A928
ASTM A995
Standard Specification for Castings, AusteniticFerritic (Duplex) Stainless Steel, for PressureContaining Parts
ASTM B62
ASTM B584
ASTM D1784
ASTM D1785
CORPORATE INFORMATION
STANDARD
TITLE
ASTM D2467
ASTM D3567
ASTM D4024
ASTM F1173
ASTM F439
BSI BS 1873
BSI BS 3799
BSI BS 5152
BSI BS 5351
BSI BS 5352
EEMUA 144
EEMUA 145
EEMUA 146
CORPORATE INFORMATION
STANDARD
TITLE
IMO A 753(18)
MSS SP-6
MSS SP-70
MSS SP-71
MSS SP-72
MSS SP-80
MSS SP-83
MSS SP-88
MSS SP-95
NACE MR0175
NORSOK L-005
NORSOK M-001
Materials Selection
CORPORATE INFORMATION
3 Abbreviations
AISI
API
ASME
ASTM
BF
- Strap-Flange
BRE
- Reduction Bushing
BS
- British Standards
BUJ
- Plug
CCS
CL
- Class
CPVC
CR
- Chrome
CRC
CRL
CRUZ
- Cross
Cu-Ni
- Copper/Nikel
DN
- Nominal Diameter
EBL
EEMUA
EPDM
FLG
- Flange
FF
- Flat Face
RF
- Raised Face
CORPORATE INFORMATION
FRP
FUC
GALV
- Galvanized
GR
- Grade
HEX
- Hexagonal
IMO
IN
- Inch
- Joint
JA
- Ring Joint
JE
- Spiral Wound
JI
- Insulated Joint
JO
- Elbow
- Coupling
LRE
- Reduction Sleeve
LREFF
LREMF
LTL
MAX
- Maximum
ML
- Half Coupling
MSS
MUC
NACE
NIP
- Nipple
CORPORATE INFORMATION
NIPC
- Short Nipple
NIPL
- Niple Longo
NIPR-C
NIPR-E
NPT
NSFHT
PE
- Polyethylene
PSI
PTFE
PVC
RED
- Reduction
REDC
- Concentric Reduction
REDE
- Eccentric Reduction
RTJ
SCH
- Schedule
SDV
STD
- Standard
SW
- Socket Weld
TAM
- Plug
TEMP
- Temperature
THD
- Threaded
TRE
- Reduction Tee
UN
- Union
UN FLEX
- Flexible Union
CORPORATE INFORMATION
UN ISOL
- Insulated Union
UNS
VAG
- Needle Valve
VB
- Butterfly Valve
VE
- Ball Valve
VET
VG
- Gate Valve
VG ABRAS
VGL
- Globe Valve
VR
- Check Valve
WOL
XS
- Extra Strong
XXS
WN
- Welding Neck
CORPORATE INFORMATION
CORPORATE INFORMATION
CORPORATE INFORMATION
CORPORATE INFORMATION
CORPORATE INFORMATION
CORPORATE INFORMATION
Spec
A4
A8
B3
B4
B5
B6
B7
B7R
B9
B10
B11
B12
B14
B15
B16
B17
B19
B20
B21
B22
B23
B24
B25
C3
C4
C5
C6
C8
C9
C10
C11
C12
C14
C16
C30
E3
E4
E5
E6
E6R
E8
E9
Rev.
Q
R
D
F
G
G
C
D
H
G
B
F
C
A
0
0
0
A
A
B
C
B
D
B
A
B
F
D
G
F
0
E
C
0
0
D
A
A
F
A
E
F
Class
125
125
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
(*)
(*)
(*)
(*)
(*)
(*)
300
300
300
300
300
300
300
300
300
300
300
300
600
600
600
600
600
600
600
Service/Fluid
SFW
GW HWU SP WW
AM CNI D DW F FG H IA IG IGN IN JF PW PWH PC BG SP
HF HWP S SC
FP
F G GL P
FW
FL FW BR SW
AM DA DFC F PC PCW SP
AM BG CHW CI D DF F FG FL G IW OL P SA SN W
ADW PC PCW
PC
BW CN IW IWC SW
BW P PC PCW SWW C
AM PC
PC
F
CHW CN GW PW W WW
HWU PWH
BW DA IWC SW
BW SW
FW
DA PCW
CNI D FG H PC
HF HWP S SC
FP
F G GL P
DO
PC
AM BG CI D FG G IW P SA SN W
PCW
PC
IW SW
AM PC
PC
AM CNI D FG H PC
HWP S SC
FP
G GL P
GL
DO
PC
(*) Maximum Working Pressure (psig), according to the table Temperature and Pressure Limit, of the
respective Spec.
CORPORATE INFORMATION
Spec
E10
E10R
E11
E14
E16
E17
E30
F3
F4
F5
F6
F6R
F10
F10R
F11
F14
G3
G4
G5
G6
G6R
G10
G10P
G10R
G11
G12
G12P
G14
G16
G16P
G18
G19
H3
H5
H10
H10P
H11
H14
H30
H30P
J12
J31
J31P
Rev.
C
A
0
B
0
0
0
B
A
A
D
A
B
A
0
B
C
A
A
D
A
C
C
A
C
C
0
B
0
0
0
0
B
B
C
0
0
0
0
0
0
0
0
Class
600
600
600
600
600
600
600
900
900
900
900
900
900
900
900
900
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
2500
2500
2500
2500
2500
2500
2500
2500
10000psi
10000psi
10000psi
Service/Fluid
AM BG CI FG G IW P W
W
PCW
IW
AM DF DFC P PC
PC
PC
CNI D FG H PC
S SC
FP
GL P
GL P
BG CI G HWU IW P W
BG CI G P W
PCW
IW
CNI D FG G H P PC
S SC
FP
G GL P
GL P
BG CI G IW P W
P
BG CI G P W
PCW
PC
PC
IW
PC DFC
PC
P
PC
CNI H
FP
DP
P
PCW
IW
PC
PC
PC
P
P
CORPORATE INFORMATION
Class
Family
125
A
150
B
300
C
600
E
900
F
1500
G
Stainless steel
ASTM A312
Gr TP 316L
B4 (0C/350C)
Carbon steel
5L Gr B PSL 1
wall thickness
1,6 mm
B5 (0C/90C)
Carbon steel
API
5L Gr B PSL 1
wall thickness
3,2 mm
Stainless steel
ASTM A312
Gr TP 316L
A4 (0C/90C)
C4 (0C/350C)
Carbon steel API
Carbon steel
5L Gr B PSL 1
5L Gr B PSL 1
wall thickness
wall thickness
1,6 mm
1,6 mm
C5 (0C/90C)
Carbon steel
API
5L Gr B PSL 1
wall thickness
3,2 mm
C6 (B6 (-46C/240C)
46C/110C)
Carbon steel
Carbon steel
ASTM A333 Gr 6 ASTM A333 Gr 6
wall thickness
wall thickness
1,6 mm
1,6 mm
Metallics
A8 (0C/105C)
Carbon steel API
5L Gr B PSL 1
Galvanized
5L Gr B PSL 1
wall thickness
3,2 mm
5L Gr B PSL 1
wall thickness
3,2 mm
E6 (-46C/110C)
F6 (-46C/110C)
G3(-100C/210C) H3 (-60C/210C)
Stainless steel
Stainless steel
ASTM A358
ASTM A358
Gr 316L Cl 1 ou 3 Gr 316L Cl 1 ou
G4 (0C/350C)
Carbon steel API
5L Gr B PSL 1
wall thickness
1,6 mm
G5 (0C/90C)
H5 (0C/90C)
Carbon steel
Carbon steel API
API
5L Gr B PSL 1
5L Gr B PSL 1
wall thickness
wall thickness
3,2 mm
3,2 mm
G6 (-46C/110C)
Carbon steel
Carbon steel
Carbon steel
ASTM A333 Gr 6 ASTM A333 Gr 6 ASTM A333 Gr 6
wall thickness
wall thickness
wall thickness
1,6 mm
1,6 mm
1,6 mm
E6R(-46C/110C) F6R (-46C/110C) G6R (-46C/110C)
Carbon steel
Carbon steel
Carbon steel
ASTM A333 Gr 6 ASTM A333 Gr 6 ASTM A333 Gr 6
wall thickness
wall thickness
wall thickness
1,6 mm
1,6 mm
1,6 mm
C8 (-18C/54C) E8 (-18C/54C)
Carbon steel
Carbon steel API
API
5L Gr B PSL 1
5L Gr B PSL 1
Galvanized
Galvanized
C9 (0C/270C)
E9 (0C/150C)
Carbon steel
Carbon steel API
API
5L Gr B PSL 1
5L Gr B PSL 1
B9 (0C/270C)
Carbon steel
API
5L Gr B PSL 1
wall thickness
wall thickness
wall thickness
3,2
3,2 mm
3,2 mm
3,2 mm
B10 (0C/240C) C10 (0C/240C) E10 (-15C/210C) F10 (0C/210C)
Carbon steel
Carbon steel
Carbon steel API Carbon steel API
API
API
5L Gr B PSL 1
5L Gr B PSL 1
5L Gr B PSL 1
5L Gr B PSL 1
wall thickness
wall thickness
wall thickness
wall thickness
1,6 mm
1,6 mm
1,6 mm
1,6 mm
10
11
Stainless steel
ASTM A312
Gr TP 316L
F4 (0C/350C)
Carbon steel API
5L Gr B PSL 1
wall thickness
1,6 mm
F5 (0C/90C)
B7 (0C/90C)
CuNi 90/10 (UNS
C70600) 20 bar
B7R (0C/90C)
CuNi 90/10 (UNS
C70600) 16 bar
Stainless steel
ASTM A312
Gr TP 316L
E4 (0C/350C)
Carbon steel API
5L Gr B PSL 1
wall thickness
1,6 mm
E5 (0C/90C)
2500/10000
H/J
CORPORATE INFORMATION
12
G12 (0C/90C)
J12 (0C/65C)
ASTM A790
(UNS S32760)
G12P (0C/90C)
ASTM A790
(UNS S32760)
ASTM A790
(UNS S32760)
(piggable)
B13 (0C/120C) C13 (0C/120C)
13
Super duplex
steel
14
ASTM A928
(UNS S32750)
B14 (0C/70C)
Carbon steel
API 5L Gr B
PSL 1
(coated
polyethylene)
B15 (10C/110C)
Carbon steel
15
Mariloy S-400
16
wall thickness
1,6 mm
B16
(-46C/130C)
Duplex steel
ASTM A790
(UNS S32760)
Super duplex
steel
ASTM A928
(UNS S32750)
C14 (0C/70C)
Carbon steel
API 5L Gr B
PSL 1
(coated
polyethylene)
C16
(-46C/130C)
Duplex steel
ASTM A790
(UNS S32760)
E14 (0C/70C)
Carbon steel
API 5L Gr B
PSL 1
(coated
polyethylene)
F14 (0C/70C)
Carbon steel
API 5L Gr B
PSL 1
(coated
polyethylene)
G14 (0C/70C)
Carbon steel
API 5L Gr B
PSL 1
(coated
polyethylene)
E16(-46C/130C)
G16(-46C/130C)
Duplex steel
ASTM A790
(UNS S32760)
Duplex steel
ASTM A790
(UNS S32760)
H14 (0C/70C)
Carbon steel
API 5L Gr B
PSL 1
(coated
polyethylene)
G16P(-46C/130C)
Duplex steel
ASTM A790
(UNS S32760)
Metallic
17
B17 (0C/120C)
Carbon steel API
5L Gr B PSL 1
Wall thickness
6,4 mm
E17 (0C/90C )
Carbon steel API
5L Gr B PSL 1
Wall thickness
6,4 mm
G18 (0C/100C)
18
19
B19
(-46C/180C)
Carbon steel
ASTM A 333 Gr 6
Wall thickness
3,2 mm
G19 (-46C/70C)
Carbon steel
ASTM A 333 Gr 6
Wall thickness
3,2 mm
C30 (0C/100C)
E30 (0C/190C)
30
5L Gr X65 PSL 1
(coated
Inconel 625)
31
5L Gr X65 PSL 1
(coated
Inconel 625)
H30
(-20C/100C)
Carbon steel
API
5L Gr X65 PSL 1
(coated
Inconel 625)
H30P
(0C/100C)
Carbon steel
API
5L Gr X65 PSL 1
(coated
Inconel 625)
J31(-70C/123C)
Alloy steel
ASTM A 333 Gr 8
J31P
(-70C/123C)
Alloy steel
ASTM A 333 Gr 8
CORPORATE INFORMATION
Class
Family
125
A
150
B
20
B20 (0C/40C)
PVC ASTM
D1785 PVC 1120
21
B21 (0C/80C)
CPVC ASTM
F441 CPVC 4120
300
C
600
E
900
F
1500
G
Nonmetallics
B22(90C/110PSIG)
22
23
24
25
CORPORATE INFORMATION
2500
H
CORPORATE INFORMATION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
P
SHEET:
E&P
1 of 134
TITLE:
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 90C
(1,6 mm)
125
A4
Tag
T-01A
Size
(in)
Wall or class
1/2" - 1 1/2"
Sch 80
2" - 6"
Sch 40
8" - 12"
Sch 20
Valves
Ends
Material
THD
(Note 5)
API 5L Gr B PSL 1
seamless
BW
API 5L Gr B PSL 1
seamless
or
welded (E=0,95)
Ball
Size
Description
1/2" - 1 1/2"
VG-36
2" - 12"
VG-34
14" - 24"
VG-35
1/2" - 1 1/2"
VGL-16
2" - 10"
VGL-18
1/2" - 1 1/2"
VR-25
2" - 24"
VR-49
Tag
T-02A
T-02B
T-02A
Pipe
T-02B
T-02A
14"
Sch 10
T-02B
16" - 20"
22" - 24"
Elbow 90
JO-01
Elbow 45
JO-02
Tee
TE-01
Cross
CRUZ-01
API 5L Gr B PSL 1
welded (E=0,95)
0,281"
Gate
3000
Bushing
BRE-01
Half Coupling
ML-01
1/2" - 1 1/2"
6000
3000
(Note 4)
Fittings
(Notes 1 and 9)
ASTM A 105
Plug
BUJ-01
Cap
TAM-01
6000
Union
UN-01
Flex Un.
UN FLEX-01
1"
Ins. Un.
UN ISOL-01
1" - 1 1/2"
Coupling
L-06
THD
(Note 5)
3000
Globe
Short Nip.
API 5L Gr B PSL 1
seamless
T-01A
1/2" - 1 1/2"
Long Nip.
Red. Nip. C.
NIPRC-01
Red. Nip. E.
NIPRE-07
Red. Nip. C.
NIPRC-04B
Red. Nip. E.
NIPRE-10B
S. R. ELL 90
CRC-01
L. R. ELL 90
CRL-01
BW/THD
(Note 5)
1/2" - 4"
L. R. ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Wall Thickness
according to pipe
2" - 24"
Ecc. Red.
REDE-01
Cap.
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
Check
BW
Butterfly
2" - 10"
ASTM A 105
12" - 24"
2" - 6"
8" - 24"
(Note 8)
VB-01
VB-02
VB-09
VB-10
Other
2 1/2"
FLG-01B
Flange
FLG-02A
(Notes 6 and 7)
FLG-04B
1/2" - 1 1/2"
THD (FF)
SO (FF)
150
2" - 24"
BLIND (FF)
JPH-09
1/2" - 10"
JPH-10
12" - 24"
JI-02
1/2" - 24"
Nut
1/16" (1,6mm)
Compressed non-asbestos
(aramida fiber and NBR)
FF
(Note 10)
Stud
ASTM A 105
WN (FF)
FLG-05B
Gasket
1/8" (3,2mm)
Fenolic resin with neoprene
ASTM A 193 Gr B7
(Note 2)
1/2" - 1 1/4"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VGL-31
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
P
SHEET:
E&P
TITLE:
2 of 132
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 90C
(1,6 mm)
125
A4
Temp. (C)
up to 66
200
up to 66
150
90
190
90
135
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Threaded connections must be weld sealed in case of vibration.
6 Flanges 1 1/2" may be used, if strictly necessary.
7 Use weldneck flanges when directly connected to but-weld fittings.
8 For pressures above 150 psig, use VB-09 and VB-10.
9 Use Plug (BUJ-01) after drains and vents blocking.
10 Isolating joint see drawing on the appendix 15.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 105C
______
125
A8
Tag
T-05A
T-02A
(Notes 5 and 9)
T-02A
Valves
Size
(in)
Wall or class
Ends
Material
1/2" - 1 1/2"
Sch 80
PLAIN
API 5L Gr B PSL 1
seamless
2" - 6"
Sch 40
T-02B
Pipe
BW
8" - 12"
Sch 20
API 5L GR B PSL 1
seamless
or
welded (E=0,85)
(Notes 1 and 3)
T-02B
Fittings
3 of 132
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Red. Coupling
LRE-01
Cap
TAM-05
Union
UN-04
Coupling
L-04
Short Nip.
3000
Size (in)
Description
Tag
1/2" - 1 1/2"
VE-44
2" - 4"
6" - 12"
NIPRC-04
NIPRE-10
1/2" - 1 1/2"
Red. Nip. C
NIPRC-04A
VG-100
Red. Nip. E
NIPRE-10A
2" - 12"
VG-34
2" - 10"
VE-22E
ASTM A 105
PLAIN
Red. Nip. E
VE-17E
API 5L Gr B PSL 1
seamless
T-05A
Red. Nip. C
VE-10E
1/2" - 1 1/2"
Long Nip.
Wall
thickness
according to
pipe
L. R. Elbow 90 CRL-01
L. R. Elbow 45 CRL-02
Gate (Note 4 )
BW/PLAIN
1/2" - 4"
S. R. Elbow 90 CRC-01
Tee
SW
Ball (Note 4)
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
2" - 12"
BW
Globe (Note 4)
VGL-18
ASTM A 105
Check
FLG-05B
Gasket
(Note 4)
Stud
Nut
150
FLG-04B
1/2" - 12"
JPH-07
1/2" - 10"
1/16" (1,6mm)
JPH-08
12" - 24"
1/8" (3,2mm)
JPH-09
1/2" - 10"
1/16" (1,6mm)
JPH-10
12" - 24"
JI-02
1/2" - 24"
VR-127
2" - 12"
VR-49
1/2" - 1 1/2"
BLIND (FF)
1/2" - 12"
Flange
(Note 6)
1/2" - 1 1/2"
Other
ASTM A 105
WN (FF)
RF
Compressed non-asbestos
(aramida fiber and NBR)
FF
1/8" (3,2mm)
Fenolic resin with neoprene
ASTM A 193 Gr B7
(Note 2)
1/2" - 7/8"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-08
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
4 of 132
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 105 C
______
125
A8
Temp. (C)
up to 65
200
80
194
105
185
Temp. (C)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 Use niple THD X PLAIN and threaded cap (TAM-04) after drains and vents blocking.
4 Use flat face gasket (JPH-10) for gate, globe and check valves assembly. For ball valves use raised face gasket (JPH-07).
5 Piping spools must be galvanized after manufacturing to ASTM A 123.
6 Flanges 1 1/2" may be used, if strictly necessary.
7 For onshore facilities only, stub in connections may be used according to ASME B31.3.
8 Use Spec A8 only for vent in Naval Systems.
9 On Naval Systems the wall thickness must be: DN 2" - Sch 80 /// 2" < DN < 10" - Sch 40 /// DN 10" - (0.500) XS.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
5 of 134
TITLE:
Temp.
Range
Service
CODE
F-Safety System and Flare (Note 11); FG-Fuel Gas (Note 9); IGN-Ignition Line; PC-Process (Corrosive
Hydrocarbon) (Note 10); CNI-Corrosive Chemical Injection (Except Sodium Hypoclorite); IAInstrumention Air; H-Hydraulic Fluid; IG-Instrumention Gas; IN-Instrumention Nitrogen; D- Diesel (Note
-100C / 370C
7); JF-Aviation Kerosene; PW-Potable Water (Note 8); PWH-Hot fresh water (Note 8); BG-Inerte gas
(Notes 12 and 14); SP-Tank Vent & Sounding (Notes 14 and 15); DW- Distilled water; AM-Amine (Note
16).
ASME B31.3
Tag
T-11
Wall or Class
Ends
Material
1/2" - 1 1/2"
Sch 40S
PLAIN
2" - 10"
Sch 10S
Sch 40S
Sch 10S
Size
18" - 20"
Sch 40S
22"
Sch 20
24"
Sch 40S
2" - 4"
Pipe
T- 30
(Note 18)
BW
26" - 28"
0.438"
30"
Sch 10
32"
Sch 20
34"
Sch 30
6" - 24"
1/2" - 1 1/2"
2" - 4"
Elbow 90
JO-23
Elbow 45
JO-24
Tee
TE-15
Red. Tee
TRE-10
(Notes 1 and 5)
6" - 24"
Cross
CRUZ-15
Half Coupling
ML-09
3000
Red. Coupling
SW
UN-12
Coupling
L-13
Short Nip.
T-11
Long Nip.
1/2" - 1 1/2"
TAM-19
Union
________
150
B3
(Note 16)
(Note 4)
Description
Ball valve; class 800; SW;
stainless steel, RPTFE seat, 46C to 150C.
Ball valve; class 150; FLG; RF;
stainless steel, RPTFE seat, 46C to 150C.
Ball valve; class 150; FLG; RF;
gear; stainless steel, RPTFE
seat, -46C to 150C.
Ball valve; class 800; SW;
stainless steel, PEEK seat, 46C to 220C.
Ball valve; class 150; FLG; RF;
stainless steel, PEEK seat, 46C to 220C.
Ball valve; class 150; FLG; RF;
gear; stainless steel, PEEK seat,
-46C to 220C.
Tag
VE-230
VE-328
VE-329
VE-240
VE-241
VE-242
1/2" - 1 1/2"
VE-231
2" - 4"
VE-148
6" - 24"
VE-149
1/2" - 1 1/2"
VE-243
(Note 18)
2" - 4"
VE-244
(Note 18)
6" - 24"
VE-245
(Note 18)
LRE-05
Cap
Standard
Ball
1/2" - 1 1/2"
12"
Class
Valves
NPS
(in)
14" - 16"
Corrosion
Allowance
PLAIN
Red. Nip. C
NIPRC-07
Red. Nip. E
NIPRE-13
Red. Nip. C
NIPRC-07A
Red. Nip. E
NIPRE-13A
S.R.ELL 90
CRC-04
L.R.ELL 90
CRL-07
1/2" - 4"
L.R.ELL 45
CRL-08
Tee
TE-21
BW/PLAIN
2" - 24"
2" - 4"
Wall
thickness
according to
pipe
Red. Tee
TRE-16
Conc. Red.
REDC-04
1/2" - 1 1/2"
1/2" - 1 1/2"
BW
Ecc. Red.
REDE-04
Cap
TAM-25
Cross
CRUZ-19
Weldolet
WOL-04
2" - 34"
2" - 4"
6" - 24"
ASTM A 182 Gr F 316L
1/2" - 1 1/2"
2" - 4"
6" - 24"
Gate
VE-246
VE-247
VE-248
VE-249
VE-250
VE-251
VE-255
VE-256
VE-257
(Note 4)
1/2" - 1 1/2"
VG-52
2" - 12"
VG-18
14" - 24"
VG-19
2" - 10"
1/2" - 1 1/2"
Globe
FLG-51
FLG-50A
Flange
(Notes 6 and 12)
FLG-49A
1/2" - 1 1/2"
SW (RF)
1/2" - 24"
BLIND (RF)
2" - 24"
150
FLG-50B
WN (RF)
Check
BLIND (RF)
26" - 34"
2" - 24"
FLG-49B
Gasket
(Note 19)
WN (RF)
JE-04
1/2" - 6"
JE-05
8" - 24"
0,175" (4,4mm)
RF
JE-06
26" - 34"
JI-01
1/2" - 34"
2" - 24"
Stainless steel AISI 304 with flexiblegraphite, with inner ring AISI 304
Nut
1/2" - 1 1/2"
ASTM A 320 Gr L7
1/2" - 1 1/2"
(Notes 2)
1/2" - 1 1/2"
1/2" - 1 1/2"
ASTM A 194 Gr 7
(Notes 2)
VR-83
VR-42
VR-74
Other
Stud
VGL-10
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-26
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
Temp.
Range
Service
CODE
ASME B31.3
6 of 134
Class
Standard
________
150
B3
F-Safety System and Flare (Note 11); FG-Fuel Gas (Note 9); IGN-Ignition Line; PC-Process (Corrosive
Hydrocarbon) (Note 10); CNI-Corrosive Chemical Injection (Except Sodium Hypoclorite); IAInstrumention Air; H-Hydraulic Fluid; IG-Instrumention Gas; IN-Instrumention Nitrogen; D- Diesel (Note
-100C / 370C
7); JF-Aviation Kerosene; PW-Potable Water (Note 8); PWH-Hot fresh water (Note 8); BG-Inerte gas
(Notes 12 and 14); SP-Tank Vent & Sounding (Notes 14 and 15); DW- Distilled water;
AM-Amine (Note 16).
Temp. (C)
from -100 up to 38
230
150
174
50
221
205
161
100
192
238
154
110
189
370
130
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
6 Flanges 1 1/2" may be used, if strictly necessary.
7 Use only downstream centrifuge.
8 When Classifier especifies metallic material, this Spec shall be used.
9 Use only downstream filters.
10 This Spec should only be used when recommended in appendix 5.
11 Pipes, connections and fittings larger than 24", only to be used in F - (Flare) service.
12 For inert gas used for purge of cargo and ballast pumps in Naval Systems use only B3.
13 For sounding pipe in Naval Systems use only B3.
14 On Naval Systems the wall thickness must be: DN 2" - Sch 80 /// 2" < DN < 10" - Sch 40 /// DN 10" - (0.500) XS.
15 When requerid Fully Tight valve (VET), see types in appendix 14.
16 Inlet from rich Amine flash drum and outlet of Amine stripper reflux drum.
17 From -101C to -30C material shall be solution heat treated.
18 Use only for AM - Amine.
19 Isolating joint see drawing on the appendix 15.
20 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A 194
Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
07 of 134
TITLE:
Service
Temp.
Range
Corrosion
Allowance
ASME B31.3
0C / 350C
(1,6 mm)
Tag
T-05A
T-02A
Size
(in)
Wall or Class
1/2" - 1 1/2"
Sch 80
2" - 6"
Sch 40
8" - 12"
Sch 20
Ends
PLAIN
T-02B
Pipe
T-02A
BW
T-02B
14"
(Notes 1 and 4)
Fittings
Elbow 90
JO-07
Elbow 45
JO-08
Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Red. Coupling
LRE-01
Cap
TAM-05
Union
UN-04
Coupling
L-04
Short Nip.
Material
API 5L Gr B PSL 1 seamless
Standard
150
B4
(Note 6)
Ball
Size
Description
1/2" - 1 1/2"
1/2" - 1 1/2"
VG-45
2" - 12"
VG-39
14" - 24"
VG-39A
1/2" - 1 1/2"
Tag
Sch 10
16" - 18"
20" - 24"
Valves
(Note 4)
Class
Sch 20
3000
SW
ASTM A 105
1/2" - 1 1/2"
Globe
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
VGL-20
PLAIN
Red. Nip. C
NIPRC-04
Red. Nip. E
NIPRE-10
Red. Nip. C
NIPRC-04A
Red. Nip. E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
BW/PLAIN
1/2" - 4"
Wall Thickness
according to pipe
2" 24"
Gate
BW
Check
ASTM A 105
2" - 24"
2" - 24"
VR-56
VR-77
VR-76
Other
1/2" - 1 1/2"
Flange
(Note 5)
FLG-05E
1/2" - 1 1/2"
FLG-05A
1/2" - 24"
FLG-04A
2" - 24"
JE-04
1/2" - 6"
Gasket
150
8" - 24"
BLIND (RF)
ASTM A 105
WN (RF)
Stainless steel AISI 304 with
flexible-graphite
0,175" (4,4mm)
JE-05
RF
Stud
(Note 2)
Nut
SW (RF)
1/2" - 1 1/4"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
08 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 350C
(1,6 mm)
150
B4
Temp. C
up to 38
284
200
200
50
278
250
174
100
256
300
147
110
251
350
121
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
6 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
09 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 90C
(3,2 mm)
150
B5
Tag
T-05A
Size
(in)
3/4"
Wall or
Class
XXS
Valves
Ends
PLAIN
T-02A
Pipe
2" - 6"
Sch 80
BW
6000
SW
ASTM A105
XXS
PLAIN
API 5L Gr B PSL 1
seamless
Wall
thickness
according to
pipe
BW
T-02B
Half Coupling ML-03
Material
Short Nip.
3/4"
T-05A
Long Nip.
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
2" - 6"
Ball
Size
description
Tag
3/4"
VE-48D
ASTM A 105
Gate
(Note 4)
VG ABRAS-04
Globe
Check
2" - 6"
FLG-13
2" - 4"
600
FLG-15
Flange
(Note 4)
FLG-04A
FLG-04B
2" - 6"
Nut
Butterfly
WN (RF)
ASTM A 105
2" - 6"
PE (FF)
BLIND (RF)
FLG-05B
BLIND (FF)
2" - 6"
JPH-07
2" - 6"
1/16"
(1,6mm)
RF
Compressed non-asbestos
(aramida fiber and NBR)
JA-01
2" - 4"
600
Oval
(Note 2)
VR-35
WN (RTJ)
BLIND (RTJ)
FLG-05A
Gasket
(Note 2)
Stud
150
5/8" - 3/4"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VB-03
VB-09
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
10 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 90C
(3,2 mm)
150
B5
up to 38
284
50
278
90
261
Temp.(C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 In VG ABRAS-04 assembly use FLG-13 (RTJ) flange.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
(Note 6)
ASME B31.3
Tag
T-09
Size
(in)
Wall or
Class
1/2" - 3/4"
Sch 160
1" - 1 1/2"
Sch 20
Ends
Elbow 90
JO-17
Elbow 45
JO-18
Equal Tee
TE-12
Red. Tee
TRE-08
Cross
CRUZ-12
Half Coupling
ML-07
Red. Coupling
LRE-04
Cap
TAM-12
Union
UN-09
Coupling
L-09
Elbow 90
JO-13
Elbow 45
JO-14
Equal Tee
TE-09
Red. Tee
TRE-05
Cross
CRUZ-09
Half Coupling
ML-05
Red. Coupling
LRE-03
Cap
TAM-09
Union
UN-07
Class
Standard
-46C /
240C
(1,6 mm)
150
B6
Material
PLAIN
Ball
Description
Tag
1/2" - 3/4"
VE-330C
1" - 1 1/2"
VE-330B
2" - 4"
VE-331
6" - 24"
VE-332
26" - 36"
VE-332A
1/2" - 3/4"
VE-296C
1" - 1 1/2"
VE-296B
2" - 4"
VE-297
6" - 24"
VE-298
26" - 36"
VE-298A
1/2" - 3/4"
VE-299C
1" - 1 1/2"
VE-299B
2" - 4"
VE-300
BW
22" - 24"
0,312"
26" - 28"
Sch 10
30"
0,344"
32 - 34"
STD
36"
0.406"
ASTM A 671 Gr CC 60
CL 22 welded (E=1)
1/2" - 3/4"
1/2" - 1 1/2"
6000
1/2" - 3/4"
SW
1" - 1 1/2"
3000
6" - 24"
26" - 36"
Coupling
L-08
Short Nip.
NIPRC-05
Red. Nip. E
NIPRE-16
Red. Nip. C
NIPRC-05A
Red. Nip. E
NIPRE-16A
S.R.ELL 90
CRC-02
L.R.ELL 90
CRL-03
L.R.ELL 45
CRL-04
Tee
TE-08
Red. Tee
TRE-04
Conc. Red.
REDC-02
Ecc. Red.
REDE-02
Cap
TAM-08
Cross
CRUZ-08
Weldolet
WOL-02
FLG-45
BW/PLAIN
1/2" - 4"
2" - 24"
Wall
thickness
according to
pipe
VE-301A
1" - 1 1/2"
VE-302B
2" - 4"
VE-303
6" - 24"
VE-304
26" - 36"
VE-304A
2" - 10"
1/2" - 1 1/2"
Globe
SW (RF)
1/2" - 24"
BLIND (RF)
FLG-22A
2" - 24"
150
WN (RF)
VGL-22
Check
2" - 24"
1/2" - 1 1/2'
26" - 36"
ASTM A 350 Gr LF2 CL 1
VR-52
VR-53
VR-53A
2" - 24"
VR-71
26" - 36"
VR-71A
2" - 24"
VR-78
(Note 4)
1/2" - 1 1/2"
BLIND (RF)
26 - 36
WN (RF)
JE-04
1/2" - 6"
JE-05
8" - 24"
JE-06
26" - 36"
RF
Other
ASTM A 320 Gr L7
(Note 2)
RF;
to
VE-302C
2" - 36"
Gasket
Nut
VE-301
BW
FLG-22B
Stud
RF;
to
1/2" - 3/4"
FLG-23A
FLG-23B
PLAIN
1/2" - 1 1/2"
Red. Nip. C
Flange
(Note 7)
ASTM A 333 Gr 6
seamless
T-09
Long Nip.
(Note 8)
Size
ASTM A 333 Gr 6
seamless
Sch 10
16" - 20"
T-08
(Notes 1 and 5)
Sch 40
14"
Pipe
4" - 6"
Corrosion
Allowance
Valves
Sch 80
8" - 12"
Temp.
Range
(Note 5)
2" - 3"
T-07A
11 of 134
1/2" - 1 1/2"
ASTM A 194 Gr 4/S3
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-21
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
12 of 134
CODE
ASME B31.3
SHEET:
(Note 6)
Temp.
Range
Corrosion
Allowance
Class
Standard
-46C /
240C
(1,6 mm)
150
B6
-46 / 38
284
50
278
100
256
110
251
200
200
240
180
Temp.(C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-07 or TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46C / -15C).
7 Flanges 1 1/2" may be used, if strictly necessary.
8 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
ASME B31.3
(Notes 4 and 5)
Tag
Wall or
Class
Size
(in)
Od
(mm)
1/2"
16
2,0
3/4"
25
2,0
1"
30
2,5
1 1/4"
38
2,5
1 1/2"
44,5
2,5
Pipe
Ends
JO-92
JO-93
Equal Tee
TE-91
Coupling
L-91
2"
57
2,5
2 1/2"
76,1
2,5
3"
88,9
2,5
4"
108
3,0
6"
159
3,5
8"
219,1
4,5
10"
267
5,5
12"
323,9
7,0
14"
368
8,0
16"
419
9,0
18"
457,2
9,5
20"
508
11,0
24"
610
13,0
28"
711
15,0
32"
813
17,0
36"
914
19,0
(Note 1)
Fittings and Accessories
UN-91
Cap
TAM-91
Red.Coupling F
LREFF-91
___
Valves
___
CONF-91
Conc. M
CONM-91
M.NPTxF.UC
UNADF-91
F.UCxF.NPT
UNADM-91
M.NPTxNPT
NIPADM-91
NIPADF-91
F.NPTxM.UC
BP/SPR. NPT
BRE-91
M.UCxF.NPT
Plug
BUJ-91
NPT
Male Niple
NIPM-91
M.NPT
Thredolet
THL-91
F.NPT
L.R.ELL 90
CRL-92
CRL-93
Red. Tee
TRE-93
Conc. Red.
REDC-91
Ecc. Red.
REDE-90
Cap
TAM-93
Weldolet
WOL-90
Flange
1/2" - 1 1/2"
1/2" - 1 1/2"
VG-36
2" - 12"
VG-18
14" - 24"
VG-19
28" - 36"
VG-19A
1/2" - 1 1/2"
VGL-16
2" - 10"
VGL-03
2 1/2"
VGL-31
1/2" - 1 1/2"
VR-25
2" - 24"
VR-42
28" - 36"
VR-42A
2" - 6"
VB-18
8" - 24"
VB-19
28" - 36"
VB-19A
M.NPTxM.UC
2" - 36"
Wall thickness
according to
pipe
1/2" - 1 1/2"
SO (RF)
FLG-92
2" - 24"
WN (RF)
FLG-93
2" - 24"
BLIND (RF)
150
Other
WNSE
1/2" - 36"
FLG- 132
WNBF
JPH-07
1/2" - 10"
JPH-08
12" - 36"
1/16" (1,6mm)
RF
JI-01
Nut
WN (RF)
Cu-Ni 90/10
(UNS C70620)
Pressure 20 Bar
(EEMUA 145)
BLIND (RF)
VIR- 03
1/8" (3,2mm)
Stud
BW
FLG-90
26" - 36"
Gasket
(Note 6)
Check
Cu-Ni 90/10
(UNS C70620)
Pressure 20 Bar
(EEMUA 146)
Cu-Ni 90/10
FLG-93A
Backing Flange
F.NPTxF.UC
Butterfly
FLG-92A
Stub Ends
1/2" - 36"
ASTM A 193 GR B7
(Note 3)
Tag
Gate
UC
Conc. F
TE-93
Description
BW
M.UCxF.UC
SKL-91
Tee
B7
Female
capilary
L.R.ELL 45
150
(Note 7)
Ball
Material
1/2" - 2"
Sockolet
Standard
Globe
1/2" - 1 1/2"
Union
0C / 90C
Class
PLAIN
T-92
Elbow 45
Corrosion
Allowance
Size
T-91 / T-92
Elbow 90
Temp.
Range
(Note 2)
20 Bar
T-90
T-91
13 of 134
1/2" 1 1/2"
ASTM A 194 GR 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
14 of 134
CODE
ASME B31.3
(Notes 4 and 5)
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 90C
___
150
B7
up to 90
290
Temp. (C)
Branchs Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 2 to 4.
2 Piping, connections and flanges should be specified according EEMUA 144/145/146.
3 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
4 This Spec must be used only for offshore facilities. Use Spec B10 for onshore facilities.
5 Use Spec B24 for fixed platform and uninhabited.
6 Isolating joint see drawing on the appendix 15.
7 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
15 of 134
TITLE:
CODE
Service
Temp. Range
Corrosion
Allowance
ASME B31.3
BR-Bilge (Note 7); FL-Foam Line (Note 4); FW-Fire Water (Aerated Sea Water) (Note 5);
SW-Aerated Sea Water (Naval System) (Note 8)
0C / 90C
___
Tag
(Note 2)
Size
(in)
Od
(mm)
Wall or Class
1/2"
16
2,0
3/4"
25
2,0
1"
30
2,5
1 1/4"
38
2,5
1 1/2"
44,5
2,5
2"
57
2,5
16 Bar
T-90
Valves
Ends
Class
Standard
150
B7R
(Note 9)
Ball
Material
Size
Description
1/2" - 1 1/2"
VG-36
2" - 12"
VG-18
14" - 24"
VG-19
28" - 36"
VG-19A
1/2" - 1 1/2"
VGL-16
2" - 10"
VGL-03
2 1/2"
VGL-31
1/2" - 1 1/2"
VR-25
2" - 24"
VR-42
28" - 36"
VR-42A
Tag
PLAIN
T-91
Pipe
2 1/2"
76,1
2,5
3"
88,9
2,5
4"
108
3,0
6"
159
3,0
219,1
4,0
10"
267
4,5
12"
323,9
5,5
14"
368
6,5
8"
Cu-Ni 90/10
(UNS C70620)
EEMUA 144 seamless
Gate
Cu-Ni 90/10
(UNS C70620)
EEMUA 144 seamless or welded
(E=1)
T-61 / T-62
16"
419
7,0
18"
457,2
8,0
20"
508
8,5
BW
Cu-Ni 90/10
(UNS C70620)
EEMUA 144 welded (E=1)
10,5
24"
610
28"
711
12
32"
813
13,5
36"
914
15,5
T-62
Elbow 90
JO-92
Elbow 45
JO-93
Equal Tee
TE-91
Globe
1/2" - 1 1/2'
Female capilary
Coupling
L-91
Union
UN-91
Cap
TAM-91
Red. Coupling F
LREFF-91
Red. Coupling M
LREMF-91
Sockolet
SKL-91
(Note 1)
1/2" - 2"
UC
Female Con.
CONF-91
F.NPTxF.UC
Male Con.
CONM-91
M.NPTxF.UC
UNADF-91
F.UCxF.NPT
UNADM-91
NIPADM-91
NIPADF-91
BP/SPR.NPT
BRE-91
Plug
BUJ-91
Male Nip.
NIPM-91
Thredolet
THL-91
L.R.ELL 90
CRL-92
Check
M.UC.xF.UC
M.UCxF.NPT
1/2" - 1 1/2"
M.NPTxM.UC
Cu-Ni 90/10
(UNS C7060X)
Pressure 20 Bar
(EEMUA 146)
F.NPTxM.UC
M.UCxF.NPT
Wall thickness
according to
pipe
Butterfly
NPT
M.NPT
2" - 10"
F.NPT
12" - 24"
L.R.ELL 45
CRL-93
Tee
TE-93
Red. Tee
TRE-93
28" - 36"
Conc. Red
REDC-91
Ecc. Red
REDE-90
Cap
TAM-93
L.R.EII 90
CRL-94
2" - 4"
2" - 6"
8" - 24"
L.R.EII 45
CRL-95
Tee
TE-94
Red. Tee
TRE-94
BW
28" - 36"
Cu-Ni 90/10
(UNS C7060X)
Pressure 16 Bar
(EEMUA 146)
6" - 36"
Conc. Red
REDC-92
Ecc. Red
REDE-91
Cap
TAM-94
Weldolet
WOL-90
2" - 36"
FLG-90
1/2" - 1 1/2"
8" - 24"
28" - 36"
Cu-Ni 90/10
2" - 10"
SO (RF)
FLG-92
WN (RF)
2" - 4"
Flange
FLG-93
(Note 2)
FLG-94
28" - 36"
150
FLG-95
WN (RF)
BLIND (RF)
FLG-94A
WN (RF)
26" - 36"
FLG-95A
Backing Flange
Stud
Nut
BLIND (RF)
VIR-03
Cu-Ni 90/10
(UNS C7060X)
Pressure 16 Bar
(EEMUA 145)
WNSE
1/2" - 36"
FLG-132
JPH-07
Gasket
(Note 6)
12" - 24"
BLIND (RF)
6" - 24"
Stub Ends
Cu-Ni 90/10
(UNS C7060X)
Pressure 20 Bar
(EEMUA 145)
1/2" - 10"
JPH-08
12" - 36"
JI-01
1/2" - 36"
WNBF
RF
Compressed non-asbestos
(aramida fiber and NBR)
1/16" (1,6mm)
1/8" (3,2mm)
(Note 3)
1/2" - 1 1/2"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VB-11
VB-12
VB-12A
VB-18
VB-19
VB-19A
VB-29
VB-29A
VB-25
VB-26
VB-26A
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
16 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
BR-Bilge (Note 7); FL-Foam Line (Note 4); FW-Fire Water (Aerated Sea Water) (Note 5);
SW-Aerated Sea Water (Naval System) (Note 8)
0C / 90C
___
150
B7R
up to 90
Temp. (C)
230
Branchs Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 2 to 4.
2
This Spec must be used only for offshore facilities. Use Spec B10 for onshore facilities.
Use only at Naval System, for generators and inert gas seal.
When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
17 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 240C
(Note 16)
(3,2 mm)
150
B9
Tag
Size
(in)
Wall or Class
1/2" - 3/4"
XXS
T-05A
Ball
Material
Description
Tag
1/2" - 3/4"
VE-333D
1" - 1 1/2"
VE-333B
2" - 4"
6" - 24"
VE-336
26" - 36"
VE-336A
1/2" - 3/4"
VE-305D
1" - 1 1/2"
VE-305B
2" - 4"
6" - 24"
VE-308
26" - 36"
VE-308A
1/2" - 3/4"
VE-48D
1" - 1 1/2"
VE-48B
2" - 4"
6" - 24"
VE-68
26" - 36"
VE-68A
1/2" - 3/4"
VE-337D
1" - 1 1/2"
VE-337B
2" - 4"
6" - 24"
VE-340
26" - 36"
VE-340A
1/2" - 3/4"
VE-309D
1" - 1 1/2"
VE-309B
2" - 4"
6" - 24"
VE-312
26" - 36"
VE-312A
1" - 1 1/2"
Sch 80
API 5L Gr B PSL 1
seamless
2" - 3"
T-02A
Pipe
4" - 6"
Sch 40
8" - 10"
Sch 20
12"
Sch 30
14" - 24"
Sch 20
26" - 32"
0.438"
BW
T-02B
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Half Coupling
ML-03
Red. Coupling
LRE-02
34"
0.469"
36"
Sch 20
API 5L Gr B PSL 1
welded (E=0,85)
1/2" - 3/4"
1/2" - 1 1/2"
6000
1/2" - 3/4"
(Notes 1 and 7)
Cap
TAM-06
Union
UN-05
Coupling
L-05
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
SW
1" - 1 1/2"
Half Coupling
ML-02
Red. Coupling
LRE-01
Cap
TAM-05
Union
UN-04
Coupling
L-04
ASTM A 105
T-05A
PLAIN
1/2" - 1 1/2"
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
VE-335
VE-306
VE-307
VE-50
VE-67
Long Nip.
NIPRC-04
VE-334
3000
Short Nip.
Red.Nip.C
(Note 4)
Size
PLAIN
1/2" - 4"
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
S.R.ELL 90
CRL-01
S.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-02
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
BW/PLAIN
2" - 24"
Wall
ASTM A 234 Gr WPB
thickness
according to
pipe
BW
2" - 36"
ASTM A 105
Gate
VE-338
VE-339
VE-310
VE-311
(Note 5)
1/2" - 1 1/2"
VG-45
2" - 12"
VG-03
14" - 24"
VG-04
26" - 36"
VG-04A
2" - 10"
Globe
FLG-05E
Flange
(Note 8)
1/2" - 1 1/2"
FLG-05A
1/2" - 24"
FLG-04A
2" - 24"
SW (RF)
BLIND (RF)
150
FLG-05C
WN (RF)
BLIND (RF)
26" - 36"
FLG-04C
1/2" - 1 1/2"
VR-56
2" - 24"
VR-35
26" - 36"
VR-35A
2" - 24"
VR-28
26" - 36"
VR-28A
WN (RF)
JPH-07
1/2" - 10"
JPH-08
12" - 36"
1/16" (1,6mm)
1/8" (3,2mm)
JI-01
1/2" - 36"
Gasket
(Notes 10 and 11) JE-04
1/2" - 6"
JE-05
8" - 24"
RF
0,175" (4,4mm)
Stainless steel AISI 304 with flexiblegraphite, with inner ring AISI 304
(Notes 2)
1/2" - 1 1/2"
ASTM A 193 Gr B7
(Notes 2 and 4)
1/2" - 1 1/2"
Other
(Notes 2)
1/2" - 1 1/2"
ASTM A 194 Gr 2H
(Notes 2 and 4)
1/2" - 1 1/2"
ASTM A 194 Gr 7
JE-06
26" - 36"
Stud
Nut
VGL-03
Check
ASTM A 105
1/2" - 1 1/2"
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
18 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 240C
(Note 16)
(3,2 mm)
150
B9
Temp. (C)
284
240
180
38
50
278
100
256
110
251
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16stud bolts and ASTM A194 GR
7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
7 Use niple THD X PLAIN and threaded cap (TAM-01 or TAM-15) after drains and vents blocking.
8 Flanges 1 1/2" may be used, if strictly necessary.
9 When Classifier especifies metallic material, this Spec must be used and valves shall be according to Spec B22 (FRP).
10 For temperatures ranging from 110C up to 240C, in PC service, use Spiral-Wound Gasket.
11 Isolating joint see drawing on the appendix 15.
12 When Naval Systems use only Spec B9.
13 When requerid Fully Tight valve (VET), see types in appendix 14.
14 For use condensate from K.O. drum to Amine flash drum.
15 On Naval Systems the wall thickness must be: DN 2" - Sch 80 /// 2" < DN < 10" - Sch 40 /// DN 10" - (0.500) XS.
16 In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of standard ASME B31.3.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
19 of 134
TITLE:
Service
Temp.
Range
Corrosion Allowance
Class
Standard
ASME B31.3
G-Glicol; F-Safety System and Flare; D-Diesel (Note 10); FL-Foam Line (Note 12); DF-Closed
Drain (Non-Corrosive hydrocarbon); BG-Inert Gas; SN-Start-up Nitrogen; SA-Service
Compressed Air (Utility Air); FG-Fuel Gas (Note 11); IW-Fresh And De-Aerated Sea Water
Injection (Note 9); CHW-Chilled Water (VAC) (Note 14); CI-Chemical Injection (noncorrosive); W-Industrial Water (Fresh, Non-corrosive/De-Aerated Sea Water) (Note 14); OLLubrication Oil; P-Process (non-corrosive hydrocarbon) (Naval System) (Notes 9 and 16); AMAmine (Note 19).
0C / 240C
(Notes 13 and
20)
(1,6 mm)
150
B10
Size
(in)
Tag
1/2" - 3/4"
Wall or Class
Ends
Sch 160
T-05A
Ball
Description
Tag
1/2" - 3/4"
VE-341C
1" - 1 1/2"
VE-333B
2" - 4"
VE-336
PLAIN
1" - 1 1/2"
Sch 80
API 5L Gr B PSL 1
seamless
T-02A
(Notes 4 and 9)
Size
VE-334
VE-335
2" - 3"
Sch 80
6" - 24"
4" - 6"
Sch 40
26" - 36"
VE-336A
1/2" - 3/4"
VE-313C
1" - 1 1/2"
VE-305B
2" - 4"
Ball valve; class 150; FLG; RF; carbon steel, PEEK seat,
up to 220C.
6" - 24"
Ball valve; class 150; FLG; RF; gear; carbon steel, PEEK
seat, up to 220C.
VE-308
26" - 36"
Ball valve; class 150; FLG; RF; gear; carbon steel, PEEK
seat, up to 220C.
VE-308A
1/2" - 3/4"
VE-48C
1" - 1 1/2"
VE-48B
2" - 4"
Ball valve; class 150; FLG; RF; carbon steel, over 220C.
6" - 24"
Ball valve; class 150; FLG; RF; gear; carbon steel, over
220C.
VE-68
26" - 36"
Ball valve; class 150; FLG; RF; gear; carbon steel, over
220C.
VE-68A
1/2" - 3/4"
VE-342C
1" - 1 1/2"
VE-337B
2" - 4"
Ball valve; fire tested; class 150; FLG; RF; carbon steel,
RPTFE/metallic seat, up to 150C.
6" - 24"
Ball valve; fire tested; class 150; FLG; RF; gear; carbon
steel, RPTFE/metallic seat, up to 150C.
26" - 36"
Ball valve; fire tested; class 150; FLG; RF; gear; carbon
steel, RPTFE/metallic seat, up to 150C.
Pipe
(Note 18 )
8" - 10"
Sch 20
2" - 3"
Sch 80
4" - 6"
Sch 40
8" - 10"
BW
Sch 20
12"
T-02B
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Half Coupling
ML-03
Red. Coupling
LRE-02
Cap
TAM-06
Union
UN-05
Coupling
L-05
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Red. Coupling
LRE-01
Cap
TAM-05
Union
UN-04
Coupling
L-04
Short Nip.
20" - 24"
Sch 20
26" - 32"
STD
34"
0,406"
36"
0,438"
6000
1/2" - 3/4"
SW
1" - 1 1/2"
Red .Nip.E
NIPRE-10A
L.R.ELL90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
VE-338
VE-339
VE-340
VE-340A
VE-317C
VE-309B
VE-310
2" - 4"
Ball valve; fire tested; class 150; FLG; RF; carbon steel,
PEEK/metallic seat, up to 220C.
6" - 24"
Ball valve; fire tested; class 150; FLG; RF; gear; carbon
steel, PEEK/metallic seat, up to 220C.
VE-312
PLAIN
26" - 36"
Ball valve; fire tested; class 150; FLG; RF; gear; carbon
steel, PEEK/metallic seat, up to 220C.
VE-312A
BW/PLAIN
1/2" - 1 1/2"
2" - 12"
VG-03
14" - 24"
VG-04
26" - 36"
VG-04A
NIPRC-04
CRC-01
VE-50
VE-311
API 5L Gr B PSL 1
1/2" - 1 1/2"
NIPRE-10
Gate (Note 5)
1/2" - 4"
2" - 24"
Wall thickness
according to pipe
VG-45
Globe
2" - 36"
2" - 10"
1/2" - 1 1/2"
VR-56
2" - 24"
VR-35
2" - 24"
VR-28
26" - 36"
VR-35A
26" - 36"
VR-28A
BW
FLG-05E
1/2" - 1 1/2"
SW (RF)
FLG-05A
1/2" - 24"
BLIND (RF)
FLG-04A
2" - 24"
FLG-05C
150
WN (RF)
ASTM A 105
BLIND (RF)
26" - 36"
WN (RF)
JPH-07
JPH-08
JE-04
1/2" - 10"
1/16" (1,6mm)
12" - 36"
1/8" (3,2mm)
RF
JE-05
8" - 24"
JE-06
26" - 36"
JI-01
1/2" - 36"
0,175" (4,4mm)
1/8" (3,2mm)
Butterfly (Note 9)
Compressed non-asbestos
(aramida fiber and NBR)
1/2" - 6"
VGL-03
Check
ASTM A 105
FLG-04C
Nut
1/2" - 3/4"
1" - 1 1/2"
NIPRC-04A
Stud
ASTM A 105
3000
T-05A
S.R.ELL 90
VE-307
VE-67
Red.Nip.C
Gasket
(Notes 13 and 15)
API 5L Gr B PSL 1
welded (E=0,85)
1/2" - 1 1/2"
Red .Nip.E
Flange
(Notes 6, 8 and
18)
Sch 10
1/2" - 3/4"
Long Nip.
Red.Nip.C
14" - 18"
VE-306
2" - 10"
VB-11
12" - 24"
VB-12
26" - 36"
VB-12A
2" - 6"
VB-18
8" - 24"
VB-19
26" - 36"
VB-19A
2" - 10"
VB-14
12" - 24"
VB-15
26" - 36"
VB-15A
2" - 6"
VB-16
8" - 24"
VB-17
26" - 36"
VB-17A
(Notes 2)
1/2" - 1 1/2"
ASTM A 193 Gr B7
(Notes 2 and
4)
1/2" - 1 1/2"
(Notes 2)
1/2" - 1 1/2"
ASTM A 194 Gr 2H
(Notes 2 and
4)
1/2" - 1 1/2"
ASTM A 194 Gr 7
Other
1/2" 1 1/2"
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
20 of 134
CODE
Service
Temp.
Range
Corrosion Allowance
Class
Standard
ASME B31.3
G-Glicol; F-Safety System and Flare; D-Diesel (Note 10); FL-Foam Line (Note 12); DF-Closed
Drain (Non-Corrosive hydrocarbon); BG-Inert Gas; SN-Start-up Nitrogen; SA-Service
Compressed Air (Utility Air); FG-Combustible Gas (Note 11); IW-Fresh And De-Aerated Sea
Water Injection (Note 9); CHW-Chilled Water (VAC) (Note 14); CI-Chemical Injection (noncorrosive); W-Industrial Water (Fresh, Non-corrosive/De-Aerated Sea Water) (Note 14); OLLubrication Oil; P-Process (non-corrosive hydrocarbon) (Naval System) (Notes 9 and 16); AMAmine (Note 19).
0C / 240C
(Notes 13 and
20)
(1,6 mm)
150
B10
Temp. (C)
up to 38
284
240
180
50
278
100
256
110
258
200
200
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud bolts and ASTM A194 GR 7 nuts
for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 On offshore facilities the slip-on flanges use shall be restricted to flare lines only, according to API 14E - item 4.5(2)-Use FLG-03A e FLG-03B.
7 Use niple THD X PLAIN and threaded cap (TAM-01 or TAM-15) after drains and vents blocking.
8 Flanges 1 1/2" may be used, if strictly necessary.
9 Butterfly valves, instead of ball valves, should be used for work in IW and P (cargo line).
10 Use only upstream centrifuge.
11 Use only upstream filtres.
12 Only in onshore facilities use this Spec for FL service (foam line).
13 For temperatures ranging from 110C up to 240C, in P and F services, use Spiral-Wound Gasket
14 When Classifier especifies metallic material.
15 Isolating joint see drawing on the appendix 15.
16 On Naval Systems the wall thickness must be: DN 2" - Sch 80 /// 2" < DN < 10" - Sch 40 /// DN 10" - (0.500) XS.
17 When requerid Fully Tight valve (VET), see types in appendix 14.
18 For onshore instalation use DN 2" and 3" SCH-40.
19 For use outlet of Amine stripper to booster pump suction.
20 In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of standard
ASME B31.3.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 150C
(Note 8)
___
150
B11
Tag
T-05A
Size
(in)
1" - 1 1/2"
Wall or Class
Sch 80
Ends
T-02A
Pipe
(Note 12)
4" - 6"
Sch 20
2" - 3"
Sch 80
4" - 6"
Sch 40
8" - 10"
(Notes 1 and 7)
T-02B
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Red. Coupling
LRE-01
Cap
TAM-05
Union
UN-04
Coupling
L-04
Short Nip.
Sch 20
API 5L Gr B PSL 1
welded (E=0,85)
12"
14" - 18"
Sch 10
20" - 24"
Sch 20
26" - 28"
STD
Ball
Description
Tag
1" - 1 1/2"
VE-346B
2" - 4"
26 - 28"
1" - 1 1/2"
2" - 4"
6" - 24"
1" - 1 1/2"
3000
SW
ASTM A 105
(Note 4)
Size
6" - 24"
BW
26 - 28"
VE-347
VE- 348
VE-349
VE-349A
VE-350B
VE-351
VE-352
VE-353
VE-353A
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
Red.Nip.C
API 5L Gr B PSL 1
seamless
Sch 40
8" - 10"
PLAIN
2" - 3"
21 of 134
1" - 1 1/2"
PLAIN
1" - 4"
BW/PLAIN
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Gate (Note 5)
1" - 1 1/2"
VG-70
2" - 12"
VG-71
14" - 24"
VG-72
2" - 24"
Wall
thickness
according to
pipe
BW
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
2" - 28"
ASTM A 105
Butterfly
2" - 10"
12" - 24"
26" - 28"
VB-32
VB-33
VB-33A
Globe
Flange
(Note 8)
FLG-05A
1" - 24"
FLG-04A
1" - 24"
26" - 28"
1" - 10"
JP-03
12" - 28"
JI-01
1" - 28"
Nut
(Notes 2)
(Notes 2 and
4)
(Notes 2)
(Notes 2 and
4)
VR-108
26" - 28"
VR-108A
1/8" (3,2mm)
Fenolic resin with neoprene
1" - 6"
RF
0,175" (4,4mm)
JE-06
1/16" (1,6mm)
PTFE Expanded
Stud
2" - 24"
ASTM A 105
WN (RF)
JP-01
JE-05
VR-107
Check
WN (RF)
BLIND (RF)
FLG-04C
Gasket
JE-04
(Notes 8 and 9)
1 - 1 1/2"
8" - 24"
26" - 28"
VGL-41
BLIND (RF)
150
FLG-05C
2" - 10"
1/2" - 1 1/2"
ASTM A 193 Gr B7
1/2" - 1 1/2"
1/2" - 1 1/2"
ASTM A 194 Gr 2H
1/2" - 1 1/2"
ASTM A 194 Gr 7
Other
1" - 1 1/2"
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-31
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
22 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 150C
(Note 8)
___
150
B11
38
Temp. (C)
284
150
229
50
278
100
256
110
258
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and
ASTM A 194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
7 Use niple THD X PLAIN and threaded cap (TAM-01 or TAM-15) after drains and vents blocking.
8 For temperatures ranging from 110C up to 150C use Spiral-Wound Gasket.
9 Isolating joint see drawing on the appendix 15.
10 When requerid Fully Tight Valve (VET), see types in appendix 14.
11 All piping shall be internal organic coated according Appendix 18.
12 For onshore instalation use DN 2" and 3" SCH 40.
13 Use this service only after a review of corrosivity.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENTE:
SHEET:
E&P
23 of 134
TTULO:
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 140C
(Note 11)
____
150
B12
Tag
T-17
T-19
Size
(in)
Wall or
class
Ends
Material
1/2" - 1 1/2"
Sch 40S
PLAIN
2" - 8"
Sch 10S
Pipe
Description
Tag
1/2" - 1 1/2"
VE-354
2" - 4"
VE-355
10" - 24"
BW
26" - 28"
Sch 10
30"
Sch 10S
32" - 36"
Sch 10
T-20
6" - 24"
Elbow 90
JO-29
Elbow 45
JO-30
Equal Tee
TE-18
Red. Tee
TRE-13
(Notes 1 and 3)
26" - 36"
Cross
CRUZ-18
Half Coupling
ML-12
3000
SW
1/2" - 1 1/2"
Cap
UN-15
Coupling
L-16
VE-356A
VE-364
2" - 4"
VE-365
6" - 24"
VE-366
26" - 36"
VE-366A
TAM-22
Union
VE-356
1/2" - 1 1/2"
Short Nip.
T-17
ASTM A 182 Gr F 55
(UNS S32760)
Long Nip.
PLAIN
(Note 2)
Red.Nip.C
NIPRC-09
Gate
Red.Nip.E
NIPRE-15
1/2" - 1 1/2"
VG-51
2" - 12"
VG-55
14" - 24"
VG-56
26" - 36"
VG-56A
2" - 10"
1/2" - 1 1/2"
VR-87
2" - 24"
VR-72
26" - 36"
VR-72A
1/2" - 1 1/2"
Red.Nip.C
NIPRC-09A
Red.Nip.E
NIPRE-15A
S.R.ELL 90
CRC-06
L.R.ELL 90
CRL-13
L.R.ELL 45
CRL-14
Tee
TE-25
Red. Tee
TRE-19
1/2" - 4"
Conc. Red.
REDC-07
Ecc. Red.
REDE-07
BW/PLAIN
2" - 24"
Wall
thickness
according to
pipe
BW
2" - 36"
Cap
TAM-27
Cross
CRUZ-21
Weldolet
WOL-05
Globe
ASTM A 182 Gr F 55
(UNS S32760)
VGL-37
Check
Flange
(Note 4)
FLG-71
1/2" - 1 1/2"
SW (RF)
FLG-70
1/2" - 24"
BLIND (RF)
FLG-69
2" - 24"
150
FLG-70A
WN (RF)
Other
ASTM A 182 Gr F 55
(UNS S32760)
BLIND (RF)
26" - 36"
FLG-69A
1/2" - 10"
1/16" (1,6mm)
JPH-08
12" - 36"
1/8" (3,2mm)
JE-04
Gasket
(Notes 6 and 10)
0,175" (4,4mm)
8" - 24"
26" - 36"
1/2" - 36"
1/2" - 1 1/2"
(Notes 12 and
1/2" - 1 1/2"
13)
(Notes 12)
Nut
RF
JE-06
(Note 12)
Compressed non-asbestos
(aramida fiber and NBR)
1/2" - 6"
JE-05
JI-01
Stud
WN (RF)
JPH-07
1/2" - 1 1/2"
(Notes 12 and
1/2" - 1 1/2"
13)
Stainless steel AISI 304 w/ flexiblegraphite, with inner ring AISI 304
1/8" (3,2mm)
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-28
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENTE:
SHEET:
E&P
TTULO:
24 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 140C
(Note 11)
____
150
B12
up to 38
290
50
282
100
256
110
251
120
245
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
3 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
4 Flanges 1 1/2" may be used, if strictly necessary.
5 This Spec should only be used when recommended in appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According Appendix 16 welding qualification requirements for superduplex.
8 When requerid Fully Tight valve (VET), see types in appendix 14.
9 According appendix 17 - casting qualification requirements minimum for valves superduplex.
10 For temperature over 110C, use spiral gaskets.
11 In possibility of occurrence of low temperatures up to -46C, this spec can be used in accordance with table A-1 of ASME B31.3 standard.
12 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
13 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A 194
Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
25 of 134
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
This Spec shall de used only for repair, when the plant was designed
usine pipes and fittings according with (UNS S32750). For new projects
use B12 (UNS S32760).
0C / 120C
(Note 8)
_______
150
B13
Tag
T-13
Pipe
T-15
Size
(in)
1/2" - 1 1/2"
Wall or
Class
Sch 40S
(Notes 1 and 3)
T-16
Elbow 90
JO-27
Elbow 45
JO-28
Equal Tee
TE-17
Red. Tee
TRE-12
Cross
CRUZ-17
Half Coupling
ML-11
Ball
PLAIN
Size
Description
Tag
1/2" - 1 1/2"
VE-74
2" - 4"
VE-76
6" - 24"
VE-77
1/2" - 1 1/2"
VG-50
2" - 12"
VG-55
14" - 24"
VG-56
2" - 10"
BW
10" - 24"
SW
ASTM A 182 Gr F 53
(UNS S32750)
1/2" - 1 1/2"
TAM-21
Union
UN-14
Coupling
L-15
Short Nip.
Material
ASTM A 790 (UNS S32750)
seamless
3000
(Note 7)
Ends
2" - 8"
Sch 10S
Valves
T-13
Long Nip.
PLAIN
Red. Nip. C
NIPRC-08
Red. Nip. E
NIPRE-14
Red. Nip. C
NIPRC-08A
Red. Nip. E
NIPRE-14A
S.R.ELL 90
CRC-05
L.R.ELL 90
CRL-11
L.R.ELL 45
CRL-12
Tee
TE-24
red. Tee
TRE-18
Conc. Red.
REDC-06
Ecc. Red.
REDE-06
Cap
TAM-26
Cross
CRUZ-20
Weldolet
WOL-06
Gate
(Note 2)
BW/PLAIN
1/2" - 4"
Wall
thickness
according to
pipe
Globe
BW
2" - 24"
VGL-37
ASTM A 182 Gr F 53
(UNS S32750)
Check
1/2" - 1 1/2"
2" - 24"
Flange
(Note 4)
Gasket
(Note 5)
Stud
Nut
1/2" - 1 1/2"
FLG-67
1/2" - 24"
SW (RF)
FLG-66
2" - 24"
JPH-07
1/2" - 10"
JPH-08
12" - 24"
JI-01
1/2" - 24"
(Notes 9)
1/2" - 1 1/4"
ASTM A 193 Gr B7
(Notes 9 and
10)
1/2" - 1 1/4"
(Notes 9)
1/2" - 1 1/4"
ASTM A 194 Gr 2H
(Notes 9 and
10)
1/2" - 1 1/4"
ASTM A 194 Gr 7
BLIND (RF)
ASTM A 182 Gr F 53
(UNS S32750)
WN (RF)
1/16" (1,6mm)
RF
VR-86
VR-72
Other
FLG-68
150
1/2" - 1 1/2"
Compressed non-asbestos
(aramida fiber and NBR)
1/8" (3,2mm)
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-29
N:
TECHNICAL SPECIFICATION
REV:
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
26 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
This Spec shall de used only for repair, when the plant was designed
usine pipes and fittings according with (UNS S32750). For new projects
use B12 (UNS S32760).
0C / 120C
(Note 8)
_______
150
B13
Temp. (C)
up to 38
290
120
245
50
282
100
256
110
251
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
3 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
4 Flanges 1 1/2" may be used, if strictly necessary.
5 Isolating joint see drawing on the appendix 15.
6 According appendix 16 - Welding qualification requirements for superduplex.
7 According appendix 17 - Casting qualification requirements minimum for valves superduplex.
8 In possibility of occurrence of low temperatures up to -29C, this spec can be used in accordance with table A-1 of ASME B31.3
standard.
9 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
10 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM
A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
27 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 70C
_____
150
B14
Tag
T-05A
T-02A
Size
(in)
Wall or
Class
Ends
Material
1" - 1 1/2"
Sch 80
PLAIN
2" - 6"
Sch 40
8" - 10"
Sch 20
2" - 6"
Sch 40
8" - 10"
API 5L Gr B PSL 1
seamless
or
welded (E=0,85)
T-02B
Ball
Size
Description
Tag
1" - 1 1/2"
VE-44
2" - 4"
6" - 24"
VE-22E
26" - 44"
VE-22F
2" - 12"
VG-03B
14" - 24"
VG-04B
2" - 10"
Sch 20
12"
Pipe
(Note 9)
14" - 18"
Sch 10
20" - 24"
Sch 20
26" - 32"
STD
34"
0,406"
36"
0,438"
BW
Gate
XS
42"
44"
Elbow 90
JO-07
Elbow 45
JO-08
Tee
TE-05
(Note 4)
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Globe
Red. Coupling
LRE-01
Cap
TAM-05
Union
UN-04
Coupling
L-04
Short Nip.
3000
PLAIN
NIPRC-04
Red. Nip. E
NIPRE-10
Red. Nip. C
NIPRC-04A
Red. Nip. E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
FLG-04B
FLG-04B
BW/PLAIN
Wall
thickness
according to
pipe
8" - 24"
2" - 44"
26" - 44"
1" - 1 1/2"
WN (FF)
2" - 24"
WN (FF)
150
VB-12
VB-13A
VB-18
VB-19
VB-20A
1" - 1 1/2"
VR-92
2" - 24"
VR-64
ASTM A 105
26" - 44"
VR-64A
1" - 1 1/2"
SO (FF)
BLIND (FF)
26" - 44"
WN (FF)
Other
SO (FF)
JPH-09
1" - 10"
1/16" (1,6mm)
JPH-10
12" - 44"
1/8" (3,2mm)
FF
Compressed non-asbestos
(aramida fiber and NBR)
ASTM A 193 Gr B7
(Note 7)
VB-11
BLIND (FF)
FLG-02B
Nut
Check
FLG-05D
Stud
2" - 6"
ASTM A 234 Gr WPB
BW
FLG-02A
FLG-04D
2" - 10
26" - 36
2" - 24"
VGL-03A
Butterfly
12" - 24"
1" - 4"
FLG-05B
Gasket
(Note 10)
ASTM A 105
API 5L Gr B PSL 1
seamless
T-05A
Red. Nip. C
Flange
(Note 6)
SW
1" - 1 1/2"
Long Nip.
VE-17E
API 5L Gr B PSL 1
welded (E=0,85)
38"
40"
VE-10E
1/2" - 1 1/2"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-08
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
28 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 70C
_____
150
B14
38
Temp. (C)
284
50
278
70
269
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 This Spec must be used only for offshore facilities. Use Spec B10 for onshore facilities.
3 When Classifier especifies metallic material, this Spec must be used and valves shall be according to Spec B22 (FRP).
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
6 Flanges 1 1/2" may be used, if strictly necessary.
7 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
8 For CN service where the classifier does not allow PVC (B20) and requires metal material, use B14 pipes and connections and B20
valves.
9 All piping must be polyetilen internally coated, according to appendix 13.
10 Isolating joint see drawing on the appendix 15.
11 BW-ballast, for Naval Systems, use Spec B15.
12 At Naval System, use in main deck distribution.
13 When requerid Fully Tight Valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL ESPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
29 of 134
TTTLE:
Service (Note 4)
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
BW-Ballast (Note 4); P-Load line (Naval System); PCW-Produced Water (Note 4); CLoad System (Auxiliary/Main) (Note 6); PC-Slop Unloading System (Naval System);
SWW-Aereated Sea Flushing Water (Naval System).
10C / 110C
(1,6 mm)
150
B15
Tag
Size
(in)
Valves
Pipe
OD
(mm)
Wall
T-05A
1/2" - 1 1/2"
Sch 160
T-02A
2" - 3"
Sch 80
Pipe
4"
114.3
5"
141.3
10 mm
6"
168.3
11 mm
8"
219.1
13 mm
10"
273.0
13 mm
12"
323.8
13 mm
14"
355.6
13 mm
16"
406.4
14 mm
18"
457.2
14 mm
20"
508.0
15 mm
22"
558.8
15 mm
24"
609.6
17 mm
26"
660.4
17 mm
End
Material
PLAIN
API 5L Gr B PSL 1
seamless
Item
Tag
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Half Coupling
ML-03
(Note 5)
Size
Description
Tag
1/2" - 1 1/2"
VE-04C
2" - 4"
10 mm
VE-10
VE-17
BW
T-21
Ball
(Note 8)
Globe
2" - 10"
VGL-03
28"
711.2
18 mm
30"
762.0
19 mm
32"
812.8
19 mm
36"
914.4
21 mm
Check
Ends
1/2" - 1 1/2"
VR-56
2" - 24"
VR-35
26" - 36"
VR-35A
2" - 10"
Size (in)
Wall or Class
6000
SW
Material
ASTM A 105
(Note 1)
1/2" - 1 1/2"
Red. Coupling
LRE-02
Cap
TAM-06
Union
Coupling
Butterfly
UN-05
L-05
12" - 24"
NIPRE-10
26" - 36"
NIPRE-10A
90 SR Elbow
CRC-01
90 LR Elbow
CRL-01
45 LR Elbow
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Reduct.
REDC-01
Conc. Reduct.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
2" - 36"
90 SR Elbow
CRC-07
4" - 24"
90 LR Elbow
CRL-19
Tee
TE-28
BW/PLAIN
2" - 6"
8" - 24"
ASTM A 234 Gr WPB
26" - 36"
2" - 3"
Wall thickness
according to pipe
2" - 6"
8" - 24"
BW
ASTM A 105
26" - 36"
Red. Tee
TRE-22
Coupling
L-21
Conc. Reduct.
REDC-10
4" - 36"
2" - 10"
12" - 24"
26" - 36"
FLG-04A
2" - 24"
WN (RF)
FLG-03A
(Note 7)
VB-14
VB-15
VB-15A
VB-16
VB-17
VB-17A
VB-23
VB-24
VB-24A
VB-25
VB-26
VB-26A
SO (RF)
4" - 24"
Flange
150
FLG-05A
FLG-03B
BLIND (RF)
ASTM A 105
SO (RF)
26" - 36"
FLG-05C
Gasket
(Note 3)
2" - 10"
JPH-08
12" - 36"
Nut
1/16" (1,6mm)
RF
2" - 36"
Other
Compressed non-asbestos
(aramida fiber and NBR)
1/8" (3,2mm)
JI-01
Stud
BLIND (RF)
JPH-07
1/2 1 1/2
Fenolic resin with neoprene
ASTM A 193 Gr B7
(Note 2)
1/2" - 2"
ASTM A 194 Gr 2H
THE DATA OR PART THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMITION
VAG-17
N:
REV:
TECHNICAL ESPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
30 of 134
TTTLE:
CODE
Service (Note 4)
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
BW-Ballast (Note 4); P-Load line (Naval System); PCW-Produced Water (Note 4); CLoad System (Auxiliary/Main) (Note 6); PC-Slop Unloading System (Naval System);
SWW-Aereated Sea Flushing Water (Naval System).
10C / 110C
(1,6 mm)
150
B15
up to 38
284
50
278
100
256
110
251
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 Isolating joint see drawing on the appendix 15.
4 Use only for Naval Systems.
5 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A 194 Gr 7 nuts
for this valves assembly shall be Zn-Ni coated.
6 Use Spec B10 for drop line of Naval Systems.
7 Use at sea chest, VB-23, VB-24 and VB-24A.
8 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PART THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMITION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENTE:
SHEET:
E&P
1 of 2
TTULO:
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 130C
(Note 12)
____
150
B16
Tag
T-36
T-37A
Size
(in)
Wall or
class
Ends
1/2" - 1 1/2"
Sch 40S
PLAIN
Material
2" - 8"
Ball
Size
Description
Tag
1/2" - 1 1/2"
VE-209
2" - 4"
VE-210
6" - 24"
VE-211
26" - 28"
VE-211A
1/2" - 1 1/2"
VE-387
2" - 4"
VE-388
6" - 24"
VE-389
26" - 28"
VE-389A
1/2" - 1 1/2"
VE-212
2" - 4"
VE-213
6" - 24"
VE-214
26" - 28"
VE-214A
1/2" - 1 1/2"
VE-390
2" - 4"
VE-391
6" - 24"
VE-392
26" - 28"
VE-392A
1/2" - 1 1/2"
VG-88
2" - 12"
VG-89
14" - 24"
VG-90
26" - 28"
VG-90A
2" - 10"
1/2" - 1 1/2"
VR-119
2" - 24"
VR-120
26" - 28"
VR-120A
Sch 10S
BW
Pipe
10" - 24"
T-37B
(Notes 1 and 3)
26" - 28"
Elbow 90
JO-45
Elbow 45
JO-46
Equal Tee
TE-38
Red. Tee
TRE-33
Cross
CRUZ-32
Half Coupling
ML-18
Sch 10
3000
SW
TAM-35
Union
UN-23
Coupling
L-27
Short Nip.
T-36
ASTM A 182 Gr F 51
(UNS S31803)
Long Nip.
PLAIN
Red.Nip.C
NIPRC-11
Red.Nip.E
NIPRE-18
Red.Nip.C
NIPRC-11A
Red.Nip.E
NIPRE-18A
1/2" - 4"
S.R.ELL 90
CRC-22
L.R.ELL 90
CRL-30
L.R.ELL 45
CRL-31
Tee
TE-39
Red. Tee
TRE-34
Conc. Red.
REDC-15
BW/PLAIN
2" - 24"
Wall
thickness
according to
pipe
BW
2" - 28"
Ecc. Red.
REDE-14
Cap
TAM-36
Cross
CRUZ-33
Weldolet
ASTM A 182 Gr F 51
(UNS S31803)
WOL-07
Gate
Flange
(Note 4)
FLG- 120
1/2" - 1 1/2"
SW (RF)
FLG- 121
1/2" - 24"
BLIND (RF)
FLG-122
2" - 24"
150
FLG-121A
WN (RF)
ASTM A 182 Gr F 51
(UNS S31803)
26" - 28"
WN (RF)
JPH-07
1/2" - 10"
1/16" (1,6mm)
JPH-08
12" - 28"
1/8" (3,2mm)
JE-04
Gasket
(Notes 6 and 10)
1/2" - 6"
JE-05
8" - 24"
26" - 28"
JI-01
1/2" - 28"
1/2" - 1 1/2"
(Notes 13 and
1/2" - 1 1/2"
14)
(Notes 13)
Nut
RF
1/2" - 1 1/2"
(Notes 13 and
1/2" - 1 1/2"
14)
Stainless steel AISI 304 w/ flexiblegraphite, with inner ring AISI 304
1/8" (3,2mm)
VGL-47
Check
Compressed non-asbestos
(aramida fiber and NBR)
0,175" (4,4mm)
JE-06
(Notes 13)
Stud
Globe
BLIND (RF)
FLG-122A
(Note 2)
Fenolic resin
Other
ASTM A 193 Gr B7
ASTM A 193 Gr B16
ASTM A 194 Gr 2H
1/2" - 1 1/2"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-35
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENTE:
SHEET:
E&P
TTULO:
2 of 2
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 130C
(Note 12)
____
150
B16
up to 38
290
50
282
100
256
110
251
130
240
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
3 Use niple THD X PLAIN and threaded cap (TAM) after drains and vents blocking.
4 Flanges 1 1/2" may be used, if strictly necessary.
5 This Spec should only be used when recommended in appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According Appendix 16 - welding qualification requirements for duplex and superduplex steel.
8 When requerid Fully Tight Valve (VET), see types in appendix 14.
9 According appendix 17 - casting qualification requirements minimum for valves duplex and superduplex steel .
10 For temperature over 110C, use spiral gaskets.
11 For use Regeneration package inlet.
12 In possibility of occurrence of low temperatures up to -46C, this spec can be used in accordance with table A-1 of ASME B31.3 standard.
13 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
14 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A 194
Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
Temp.
Range
Corrosion
Allowance
0C / 120C
(Notes 8 and
11)
(6.4 mm)
CODE
ASME B31.3
Size
(in)
Tag
T-05A
Pipe
3/4" - 1 1/2"
T-02A
Elbow 90
JO-37
Elbow 45
JO-38
Equal Tee
TE-34
Red. Tee
TRE-29
Cross
CRUZ-28
ML-14
Red. Coupling
LRE-12
Cap
XXS
2"
Sch 80
3"
Sch 160
4"
Sch 80
6"
0,344"
8"
0,375"
10"
0,438"
12"
0,406"
Ends
Material
PLAIN
API 5L Gr B PSL 1
seamless
BW
API 5L Gr B PSL 1
seamless
or
API 5L Gr B PSL 1
welded (E=0,95)
Ball
9000
SW
B17
(Note 4)
Description
Tag
3/4" - 1 1/2"
VE-333D
2" - 4"
6" - 12"
VE-336
3/4" - 1 1/2"
VE-337D
2" - 4"
6" - 12"
VE-334
VE-335
VE-338
VE-339
VE-340
(Note 5)
3/4" - 1 1/2"
VG-45
2" - 12"
VG-03
2" - 10"
3/4" - 1 1/2"
VR-56
2" - 4"
VR-35
ASTM A 105
Globe
VGL-03
TAM-31
Union
UN-19
Coupling
L-23
Check
T-05A
API 5L Gr B PSL 1
Long Nip.
3/4" - 1 1/2"
(Note 1)
150
(Note 10)
Size
Short Nip.
Standard
Gate
3/4" - 1 1/2"
Half Coupling
Wall or Class
Valves
Class
Red.Nip.C
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
3/4" - 4"
L.R.ELL 90
CRL-01
Ecc. Red.
REDE-01
2" - 24"
PLAIN
Wall
thickness
according to
pipe
BW/PLAIN
Butterfly
ASTM A 234 Gr WPB
BW
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
Flange
(Note 7)
Gasket
(Notes 8 and 9)
2" - 36"
ASTM A 105
FLG-05E
3/4" - 1 1/2"
FLG-05A
3/4" - 24"
FLG-04A
2" - 24"
3/4" - 10"
1/16" (1,6mm)
JPH-08
12"
1/8" (3,2mm)
JE-04
3/4" - 6"
JE-05
8" - 12"
Nut
3/4" - 12"
BLIND (RF)
ASTM A 105
WN (RF)
JPH-07
JI-01
Stud
SW (RF)
150
Compressed non-asbestos
(aramida fiber and NBR)
RF
0,175" (4,4mm)
Stainless steel AISI 304 with flexiblegraphite, with inner ring AISI 304
1/8" (3,2mm)
(Notes 2)
1/2" - 1 1/2"
ASTM A 193 Gr B7
(Notes 2 and
4)
1/2" - 1 1/2"
(Notes 2)
1/2" - 1 1/2"
ASTM A 194 Gr 2H
1/2" - 1 1/2"
ASTM A 194 Gr 7
(Notes 2 and
4)
Other
3/4 1 1/2
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 120C
(Notes 8 and
11)
(6,4 mm)
150
B17
up to 38
284
50
278
100
256
110
251
240
180
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A 194 Gr 7 nuts
for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-01 or TAM-15) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 For temperatures ranging from 110C up to 240C, use Spiral-Wound Gasket
9 Isolating joint see drawing on the appendix 15.
10 When requerid Fully Tight valve (VET), see types in appendix 14.
11 In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of standard ASME
B31.3.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
ASME B31.3
Tag
T-09
T-07A
Pipe
(Notes 1 and 5)
T-08
Elbow 90
JO-17
Elbow 45
JO-18
Equal Tee
TE-12
Red. Tee
TRE-08
Cross
CRUZ-12
Half Coupling
ML-07
Red. Coupling
LRE-04
Cap
TAM-12
Union
UN-09
Coupling
L-09
Elbow 90
JO-13
Elbow 45
JO-14
Equal Tee
TE-09
Red. Tee
TRE-05
Cross
CRUZ-09
Half Coupling
ML-05
Red. Coupling
LRE-03
Cap
TAM-09
Union
UN-07
Coupling
L-08
Short Nip.
Size
(in)
Wall or
Class
1/2" - 3/4"
Sch 160
1" - 1 1/2"
Sch 80
2" - 3"
Sch 80
4"
Sch 30
6"
0,203"
8"
0,219"
10" - 12"
Sch 20
14"
0.281"
16"
0.312
20" - 22"
0.344"
24"
Sch 20
26"
STD
28"
0.406"
NIPRC-05
Red. Nip. E
NIPRE-16
Red. Nip. C
NIPRC-05A
Red. Nip. E
NIPRE-16A
S.R.ELL 90
CRC-02
L.R.ELL 90
CRL-03
L.R.ELL 45
CRL-04
Tee
TE-08
Red. Tee
TRE-04
Conc. Red.
REDC-02
Ecc. Red.
REDE-02
Cap
TAM-08
Cross
CRUZ-08
Weldolet
WOL-02
FLG-45
Standard
-46C /
180C
(3,2 mm)
150
B19
Valves
Material
PLAIN
ASTM A 333 Gr 6
seamless
ASTM A 671 Gr CC 60
CL 22 welded (E=1)
1/2"
SW
3/4" - 1 1/2"
Ball
Description
Tag
1/2" - 3/4"
VE-330C
1" - 1 1/2"
VE-330B
2" - 4"
VE-331
6" - 24"
VE-332
26" - 36"
VE-332A
1/2" - 3/4"
VE-296C
1" - 1 1/2"
VE-296B
2" - 4"
VE-297
6" - 24"
VE-298
26" - 36"
VE-298A
1/2" - 3/4"
VE-299C
1" - 1 1/2"
VE-299B
2" - 4"
VE-300
3000
6" - 24"
26" - 36"
ASTM A 333 Gr 6
seamless
VE-301
VE-301A
1/2" - 3/4"
VE-302C
1" - 1 1/2"
VE-302B
2" - 4"
VE-303
6" - 24"
VE-304
26" - 36"
VE-304A
2" - 10"
1/2" - 1 1/2"
VR-52
2" - 24"
VR-53
26" - 36"
VR-53A
2" - 24"
VR-78
(Note 4)
1/2" - 1 1/2"
PLAIN
1/2" - 4"
BW/PLAIN
2" - 24"
Globe
BW
SW (RF)
1/2" - 24"
BLIND (RF)
FLG-22A
2" - 24"
150
WN (RF)
VGL-22
Check
2" - 36"
1/2" - 1 1/2'
BLIND (RF)
26 - 36
WN (RF)
JE-04
1/2" - 6"
JE-05
8" - 24"
JE-06
26" - 36"
RF
Other
ASTM A 320 Gr L7
(Note 2)
(Note 8)
Size
BW
6000
Gasket
Nut
Class
1/2" - 1 1/2"
FLG-22B
Stud
Ends
FLG-23A
FLG-23B
Corrosion
Allowance
1/2" - 3/4"
1/2" - 1 1/2"
Red. Nip. C
Temp.
Range
(Note 5)
T-09
Long Nip.
Flange
(Note 7)
(Note 6)
1/2" - 1 1/2"
ASTM A 194 Gr 4/S3
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-21
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
ASME B31.3
(Note 6)
Temp.
Range
Corrosion
Allowance
Class
Standard
-46C /
180C
(3,2 mm)
150
B19
-46 / 38
284
50
278
100
256
110
251
200
200
Temp.(C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-07 or TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46C / -15C).
7 Flanges 1 1/2" may be used, if strictly necessary.
8 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
31 of 134
CODE
(Note 8)
CHW-Chilled Water (VAC) (Note 4);W-Industrial Water (Fresh, Non-Corrosive/Deaerated Sea Water) (Note 4); GW-Grey Water; PW-Potable Water (Note 5); WWSewage Waste Water; CN-Sodium Hypoclorite (Note 6)
ASME B31.3
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 40C
______
(Note 7)
B20
Tag
(Note 1)
Pipe
T-22
Size
(in)
1/2" - 8"
Wall or Class
Sch 80
Valves
Ends
Material
PLAIN
PVC
Poly Vynil Chloride
ASTM D1785 PVC 1120
Dimensions ASTM D1785
Elbow 90
JO-31
Elbow 45
JO-32
Equal Tee
TE-19
Red. Tee
TRE-14
Red. Bushing
BRE-05
Red. Coupling
LRE-09
Cap
TAM-23
Coupling
L-17
Niple
T-22
Union
UN-16
1/2" - 4"
Tee 45
TEY-01
1/2" - 6"
Female Con.
ADPTF-01
1/2" - 2"
SW/THD
Plug
BUJ-07
1/2" - 2"
THD
Ball
Size
Description
Tag
1/2" - 8"
VE-159
2 1/2" - 8"
SW
1/2" - 8"
PVC
Poly Vynil Chloride
ASTM D1784 class 12454
Dimensions ASTM D2464
Sch 80
PLAIN
SW
Butterfly
VB-27
Globe
Check
FLG-75
Flange
1/2" - 8"
FLG-74
150
According to
ASME B16.5
only for
dimensions
SW (FF)
BLIND (FF)
1/2" - 4"
1/2" - 1 1/2"
VR-89
PVC
Poly Vynil Chloride
ASTM D1784 class 12454
Drilling ASME B16.5
Needle
Gasket
Stud
Nut
JPH-15
1/2" - 8"
1/8" (3,2mm)
FF
(Notes 2 and 3)
1/2" - 3/4"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-08
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
Service
CODE
ASME B31.3
32 of 134
Corrosion
Allowance
Class
Standard
0C / 40C
______
(Note 7)
B20
0oC 23oC
30oC
35oC
40oC
(Note 8)
CHW-Chilled Water (VAC) (Note 4);W-Industrial Water (Fresh, Non-Corrosive/Deaerated Sea Water) (Note 4); GW-Grey Water; PW-Potable Water (Note 5); WWSewage Waste Water; CN-Sodium Hypoclorite (Note 6)
DN
TEMPERATURE
DN
TEMPERATURE
0oC 23oC
30oC
35oC
40oC
1/2"
848 psi
636 psi
526 psi
424 psi
2 1/2"
425 psi
319 psi
263 psi
212 psi
3/4"
688 psi
516 psi
426 psi
3"
375 psi
281 psi
233 psi
188 psi
1"
630 psi
473 psi
391 psi
344 psi
315 psi
4"
324 psi
243 psi
201 psi
162 psi
1 1/2"
471 psi
404 psi
353 psi
303 psi
292 psi
251 psi
235 psi
202 psi
6"
279 psi
209 psi
173 psi
140 psi
8"
246 psi
185 psi
153 psi
123 psi
2"
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 Use plan washers to distribute the load of PVC flange.
4 Use spec B10 when Classifier especifies metallic material.
5 Use spec B3 when Classifier especifies metallic material.
6 Use spec B14 when Classifier especifies metallic material.
7 Table according - Pressure / Temperature rating.
8 PVC piping use is restricted to inside living quarter modules, out of risk areas or line not crossing classified bulkhead.
9 For threaded fittings, use 50% of Working Mx. Pressure table above.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
33 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
10C / 80C
______
(Note 6)
B21
Tag
Pipe
T-23
Size
(in)
1/2" - 8"
Wall or Class
Sch 80
Valves
Ends
PLAIN
Elbow 90
JO-33
Elbow 45
JO-34
Equal Tee
TE-20
Red. Tee
TRE-15
Red. Bushing
BRE-06
Red. Coupling
LRE-10
Cap
TAM-24
Coupling
L-18
Niple
T-23
Union
UN-17
1/2" - 4"
Tee 45
TEY-02
1/2" - 6"
Female Con.
ADPTF-02
1/2" - 2"
SW/THD
Plug
BUJ-08
1/2" - 2"
THD
Material
CPVC
Chlorinated Polyvinyl Chloride
ASTM F441 CPVC 4120
Dimensions ASTM F441
Ball
Size
Description
Tag
1/2" - 8"
VE-160
2 1/2" - 8"
SW
1/2" - 8"
CPVC
Chlorinated Polyvinyl Chloride
ASTM D 1784 Class 23447
Dimensions ASTM F439
Sch 80
PLAIN
SW
Butterfly
VB-28
Globe
Check
FLG-76
Flange
1/2" - 8"
FLG-77
JPH-15
1/2" - 8"
150
According to ASME
B16.5 only for
dimensions
SW (FF)
BLIND (FF)
1/8" (3,2mm)
FF
CPVC
Chlorinated Polyvinyl Chloride
ASTM D 1784 class 23447
Drilling ASME B16.5
1/2" - 3"
1/2" - 1 1/2"
Needle
Gasket
Stud
Nut
ASTM A 193 Gr B7
(Notes 2 and 3)
VR-88
1/2" - 3/4"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-08
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
34 to 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
10C / 80C
______
(Note 6)
B21
TEMPERATURE
DN
1/2"
3/4"
1"
1 1/2"
2"
TEMPERATURE
DN
0 C 27 C
38 C
60 C
80 C
848 psi
688 psi
630 psi
471 psi
404 psi
696 psi
564 psi
517 psi
386 psi
331 psi
424 psi
344 psi
315 psi
235 psi
202 psi
212 psi
172 psi
158 psi
118 psi
101 psi
2 1/2"
3"
4"
6"
8"
0 C 27 C
38 C
60 C
80 C
425 psi
375 psi
324 psi
279 psi
246 psi
348 psi
308 psi
266 psi
229 psi
202 psi
212 psi
188 psi
162 psi
140 psi
123 psi
106 psi
94 psi
81 psi
70 psi
62 psi
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 Use plan washers to distribute the load of CPVC flange.
4 Use spec A8 when Classifier especifies metallic material.
5 Use spec B3 when Classifier especifies metallic material.
6 Table according - Pressure / Temperature rating.
7 CPVC piping use is restricted to inside living quarter modules, out of risk areas or line not crossing classified bulkhead.
8 For threaded fittings use 50% of Working Mx. Pressure table above.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
35 of 134
CODE
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
BW-Ballast (Notes 9, 10 and 11); DA-Open Drain (Note 12); IWCAerated Sea Injection Water (Note 9); SW-Aerated Sea Water (Notes 9,
10 and 11)
0C / 90C
_____
(Note 13)
B22
Tag
Size
(in)
Wall (mm)
nominal
Ends
Ball
Size
Description
Tag
2" - 4"
VE-10G
VE-17G
FRP
ASTM F 1173-01
RTRP- I5B3SIFB30
(reinforced thermosetting resin
pipe)
Pipes
T-27
1" - 48"
(Note 7)
a - 4.1.1.1 (Filament-wound)
Butt and strap b - 4.1.2 resin type (according to
joint
manufacter and approved for
CLASSIFIER
1/2" - 1 1/2"
VG-02
2" - 12"
VG-59
14" - 24"
VG-60
26" - 48"
VG-60A
2" - 10"
Globe
VGL-03B
(Note 16)
L-19
Tee
TE-26
Red. Tee
TRE-20
Conc. Red.
REDC-08
Ecc. Red.
REDE-08
L.R.ELL 90
CRL-15
L.R.ELL 45
CRL-17
Saddle FLG
SAD-03
Saddle THR
Plug
SAD-05
12" - 24"
Butt and strap
joint
1" - 48"
ASTM F 1173-01
(Note 16)
2" - 6"
FLG
1/2" - 1 1/2"
FLG-83
WN (FF)
16 BAR
BLIND (FF)
VB-13A
VB-18
VB-19
26" - 48"
VB-20A
Check
1" - 1 1/2"
VR-75
2" - 24"
VR-64
26" - 48"
VR-64A
1/2" - 1 1/2"
a - 1 (filament-wound)
1" - 48"
FLG-85
FRP
ASTM D 4024-00
RTR- a;b;c
(reinforced thermosetting resin)
VB-12
VB-11
8" - 24"
THD
BUJ-06
Flange
26" - 48"
(Note 16)
Gasket
Stud
JP-01
Nut
(Notes
8 and 14)
Washer
(Note 15)
1" - 48"
1/8" (3,2mm)
FF
Needle
PTFE expanded
ASTM A 193 Gr B7
1/2" - 1 1/2"
ASTM A 194 Gr 2H
ASME B 18.22.1
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-08
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
36 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
BW-Ballast (Notes 9, 10 and 11); DA-Open Drain (Note 12); IWCAerated Sea Injection Water (Note 9); SW-Aerated Sea Water (Notes 9,
10 and 11)
0C / 90C
_____
(Note 13)
B22
Temp. (C)
up to 90
125
90
100
80
123
70
137
up to 60
145
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 This Spec shall be used according to IMO A 753, level L3.
3 Pipes and fittings must be made by the same manufacturer.
4 All the pipes, fittings and flanges shall have na enriched resin external liner and ultraviolet light inhibitor.
5 The supplier shall be responsible for the designs, manufacture, assembly, maintenance, conditioning, inspection and testing of the piping.
6 The manufacturer shall have a Certificate of Type Approval issued by the Classifier.
7 Wall thickness shall be calculated for the manufacturer.
8 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
9 When Classifier especifies metallic material, Spec B14 must be used and valves shall be according to Spec B22.
10 For the Naval System use Spec B15 only.
11 For Maximum working pressure greater than 150 PSIG, use Spec B23.
12 When Classifier especifies metallic material, Spec B9 must be used valves shall be according to Spec B22.
13 Table according - Pressure / Temperature rating.
14 The torque limit for FRP flanges shall be accordance with piping manufacturer.
15 Use plan washers to distribute the load of FRP flange.
16 This Spec should be according to appendix X3, paragraph X3.2.5.5 (electrical conductive) and appendix X4 (fatigue) with norm ASTM F1173-01.
17 Do not use FRP when the risk of the piping repture may cause flood with the lack of stability and integrity.
18 VB and VG may be used to atenuate the water hammer.
19 The piping designer/manufacturer should check the probability of the water hammer and provide a revision in the rote pipe in order to diminish.
20 When requerid Fuly Tight (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
ASME B31.3
37 of 134
BW-Ballast (Notes 9 and 10); SW-Aerated Sea Water (Notes 9, 10 and 18)
Temp. Range
Corrosion
Allowance
Class
Standard
0C / 90C
_____
(Note 11)
B23
Tag
Size
(in)
Wall (mm)
nominal
Ends
Material
Size
Description
Tag
2" - 4"
VE-10G
VE-17G
FRP
ASTM F 1173-01
RTRP- I5B3SIFB30
(reinforced thermosetting resin
pipe)
Pipe
T-23
1" - 32"
(Note 7)
1/2" - 1 1/2"
VG-02
2" - 12"
VG-59
14" - 32"
VG-60
2" - 10"
a - 4.1.1.1 (filament-wound)
b - 4.1.2 resin type (according to
manufacter and approved for
CLASSIFIER)
c - 4.1.3.2 (liner reinforced)
d - 4.2.3 (test of long duration)
e - 4.3.1.3 (stagnated water)
Globe
VGL-03B
(Note 14)
Coupling
L-19
Tee
TE-26
Red. Tee
TRE-20
Conc. Red
REDC-08
Ecc. Red.
REDE-08
L. R. ELL 90
CRL-15
L. R. ELL 45
CRL-17
Saddle FLG
SAD-03
Saddle THD
SAD-05
Plug
Butterfly
2" - 6"
1" - 32"
1/2" - 1 1/2"
Threaded
ASTM F 1173-01
(Note 14)
8" - 32"
(Note 16)
VB-19
VB-20
Flanged
BUJ-06
Check
150
According to
ASME B16.5
only for
dimensions
FLG-83
Flange
WN (FF)
16 BAR
VR-75
2" - 32"
VR-64
1/2" - 1 1/2"
FRP
ASTM D 4024-00
RTR-a;b;c
(reinforced thermosetting resin)
a - 1 (Filament-wound)
1" - 32"
FLG-85
1" - 1 1/2"
BLIND (FF)
Gasket
Stud
JP-01
Nut
(Notes
8 and 12)
Washer
(Note 13)
1" - 32"
1/8" (3,2mm)
FF
PTFE expanded
Needle
ASTM A 193 Gr B7
1/2" - 1"
ASTM A 194 Gr 2H
ASTM B 18.22.1
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-08
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
Service
CODE
ASME B31.3
38 of 134
BW-Ballast (Notes 9 and 10); SW-Aerated Sea Water (Notes 9, 10 and 18)
Temp. Range
Corrosion
Allowance
Class
Standard
0C / 90C
_____
(Note 11)
B23
90
150
80
190
70
217
up to 60
230
Temp. (C)
up to 90
125
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 This spec shall be used according to IMO A 753, level L3.
3 Pipes and fittings must be made by the same manufacturer.
4 All the pipes, fittings and flanges shall have na enriched resin external liner and ultraviolet light inhibitor.
5 The supplier shall be responsible for the design, manufacture, assembly, maintenance, conditioning, inspection and testing of the piping.
6 The manufacturer shall have a Certificate of Type Approval issued by the Classifier.
7 Wall thickness shall be calculated for the manufacturer.
8 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
9 When Classifier especifies metallic material, Spec B14 must be used and valves shall be according to Spec B23.
10 For the Naval System use Spec B15 only.
11 Table according - Pressure / Temperature rating.
12 The torque limit for FRP flanges shall be accordance with piping manufacturer.
13 Use plan washers to distribute the load of FRP flange.
14 This Spec should be according to appendix X3, paragraph X3.2.5.5 (electrical conductive) and appendix X4 (fatigue) with norm ASTM F1173-01.
15 Do not use FRP when the risk of the piping repture may cause flood with the lack of stability and integrity.
16 VB and VG may be used to atenuate the water hammer.
17 The piping designer/manufacturer should check the probability of the water hammer and provide a revision in the rote pipe in order to diminish.
18 When Naval Systems to utilize of FRP, restricted to sea water discharge fro inerte gas generators.
19 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
39 of 134
CODE
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 120C
_____
(Note 12)
B24
Tag
Size
(in)
Wall (mm)
nominal
Ends
Valves
Material
Ball
Size
2" - 4"
FRP
ASTM F 1173-01
RTRP- I5B3SIFB30
(reinforced thermosetting resin
pipe)
Pipe
T-28
1" - 16"
(Note 7)
(Note 15)
Description
Ball valve; class 150; FLG; FF;
steel.
Tag
carbon
VE-10G
VE-17G
VG-02
2" - 12"
VG-59
14" - 16"
VG-60
2" - 10"
2" - 10"
VB-11
12" - 16"
VB-12
1" - 1 1/2"
VR-75
2" - 16"
VR-64
1/2" - 1 1/2"
a - 4.1.1.1 (filament-wound)
b - 4.1.2.4 (phenolic resin)
c - 4.1.3.2 (liner not reinforced)
d - 4.2.3 (test of long duration)
e - 4.3.1.2 (stagnated water)
Globe
VGL-03B
(Note 9)
Coupling
L-20
Tee
TE-27
Red. Tee
TRE-21
Conc. Red
REDC-09
1" - 16"
Ecc. Red.
REDE-09
L.R.ELL 90
CRL-16
L.R.ELL 45
CRL-18
Saddle FLG
SAD-04
Saddle THD
SAD-06
Plug
BUJ-06
Flanged
1/2" - 1 1/2"
Threaded
ASTM A 182 Gr F 321
150
According to
ASME B16.5
only for
dimensions
FLG-86
Flange
ASTM F 1173-01
(Note 9)
WN (FF)
FRP
ASTM D 4024-00
RTR- a;b;c
(reinforced thermosetting resin)
Check
1" - 16"
a - 1 (filament-wound)
b - resin type - phenolic
FLG-88
Gasket
Stud
JP-01
Nut
(Notes 8 and
14)
Washer
(Note 13)
16 BAR
1" - 16"
1/8" (3,2mm)
BLIND (FF)
FF
PTFE expanded
Other
ASTM A 193 Gr B7
1/2" - 1"
ASTM A 194 Gr 2H
ASME B18.22.1
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-08
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
40 of 134
CODE
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 120C
_____
150
B24
(Note 12)
Temp. (C)
Temp. (C)
up to 90
150
up to 90
125
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 This spec shall be used according to IMO A 753, level L3.
3 Pipes and fittings must be made by the same manufacturer.
4 All the pipes, fittings and flanges shall have na enriched resin external liner and ultraviolet light inhibitor.
5 The supplier shall be responsible for the design, manufacture, assembly, maintenance, conditioning, inspection and testing of the piping.
6 The manufacturer shall have a Certificate of Type Approval issued by the Classifier.
7 Wall thickness shall be calculated for the manufacturer.
8 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
9 This Spec should be according to appendix X3, paragraph X3.2.5.5 (electrical conductive) and appendix X4 (fatigue) with norm ASTM F1173-01.
10 Do not use FRP when the risk of the piping repture may cause flood with the lack of stability and integrity.
11 Use only for fixed and uninhabited platforms.
12 Table according - Pressure / Temperature rating.
13 Use plan washers to distribute the load of FRP flange.
14 The torque limit for FRP flanges shall be accordance with piping manufacturer.
15 VB and VG may be used to atenuate the water hammer.
16 The piping designer/manufacturer should check the probability of the water hammer and provide a revision in the rote pipe in order to diminish.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
41 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 60C
_____
150
B25
Tag
Size
(in)
Wall (mm)
nominal
Material
RPVC - PVC extruded reinforced
external with thermosetting resin,
fiber glass
T-26
1" - 28"
RJ/EE
T-24
1" - 28"
RJ/FF
Pipe
(Note 8)
Equal Tee
Valves
Ends
Ball
Dim.
Descrio
Cod.
1" - 6"
VE-158
TE-29
Red. Tee
TRE-23
Cross
CRUZ-22
Red. Cross
CRUZR-01
S. R. ELL 90
CRC-08
S. R. ELL 45
CRC-09
Gate
1" - 28"
RJ/EE
Globe
S. R. ELL 22 30`CRC-14
S. R. ELL 11 15`CRC-17
Ecc Red.
REDE-10
Conc Red.
REDC-11
Niple
NIPC-07
Equal Tee
TE-31
Red. Tee
TRE-25
Cross
CRUZ-24
Red. Cross
CRUZR-03
S. R. ELL 90
CRC-12
S. R. ELL 45
CRC-13
2" - 8"
VGL-39
2" - 20"
VR-91
2" - 20"
VR-90
8" - 10"
VB-21
12" - 24"
VB-22
26" - 28"
VB-22A
(Note 1)
RPVC - PVC coated external with
fiber glass, thermosetting resin
Check
1" - 28"
RJ/EE
S. R. ELL 22 30`CRC-16
S. R. ELL 11 15`CRC-19
Ecc Red.
REDE-12
Conc Red.
REDC-13
FLG-82
FLG-81
Flange
(Notes 5, 11 and FLG-80
12)
FLG-79
Gasket
Stud
Nut
Washer
1" - 28"
2" - 28"
FLG-78
1" - 28"
JP-02
1" - 28"
JR/PF
150
According to
ASME B16.5
only for
dimensions
JR/BF
JE/PF
JE/BF
BLIND (FP)
1/8" (3,2mm)
FF
ASTM A 193 Gr B7
(Notes 5 and 6)
1/2" - 1 1/4"
ASTM A 194 Gr 2H
(Note 7)
ASME B 18.22.1
AS INFORMAES DESTE DOCUMENTO SO PROPRIEDADE DA PETROBRAS, SENDO PROIBIDA A UTILIZAO FORA DA SUA FINALIDADE
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
FOLHA:
E&P
42 de 134
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 60C
_____
150
B25
20
232
60
174
Temp. C
Branch Connections
Notes:
1 Wall thickness shall be according to NBR-7368.
2 Piping, conections and mend "Kit" should be the preduct of the same manufacturer.
3 Piping and conection should have ultraviolet inihibitor.
4 Water hammer shall be checked by the Engineering firm or the manufacturer.
5 The limit of torque for RPVC flanges should be based at piping diameter. Excess torque can damague the flange.
6 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
7 Use plan washers with narrow seat ASME B 27.2 tipo A.
8 For branches, use Tee or reduction Tee.
9 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
10 Butterfly valve way be used for diameters upon 6".
11 Dimensions according ASME B16.5 class 150.
12 For flanges with dimensions greater than NPS 24 according ASME B 16.47 series A for class 150.
13 For piping PP mend, use weld as the best choise at PVC.
AS INFORMAES DESTE DOCUMENTO SO PROPRIEDADE DA PETROBRAS, SENDO PROIBIDA A UTILIZAO FORA DA SUA FINALIDADE
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
43 of 134
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-46C/149C
________
300
C3
Valves (Note 9)
Tag
T-11
(Notes 1 and 4)
Pipe
T-30
Elbow 90
JO-23
Elbow 45
JO-24
Equal Tee
TE-15
Red. Tee
TRE-10
Cross
CRUZ-15
Half Coupling
ML-09
Red. Coupling
LRE-05
Cap
TAM-19
Union
UN-12
Coupling
L-13
Short Nip.
Size
(in)
Wall or Class
Ends
Material
1/2" - 1 1/2"
Sch 40S
PLAIN
2" - 4"
Sch 10S
6" - 14"
Sch 40S
16" - 20"
Sch 80S
22"
0,562"
24"
0,625"
Description
Tag
1/2" - 1 1/2"
VE-230
2" - 4"
VE-314
6" - 24"
VE-315
1/2" - 1 1/2"
VE-246
2" - 4"
3000
SW
6" - 24"
VE-259
VE-260
1/2" - 1 1/2"
T-11
Long Nip.
Red.Nip.C
BW
Ball
Size
PLAIN
NIPRC-07
Red .Nip.E
NIPRE-13
Red.Nip.C
NIPRC-07A
Red .Nip.E
NIPRE-13A
S.R.ELL 90
CRC-04
L.R.ELL 90
CRL-07
L.R.ELL 45
CRL-08
Tee
TE-21
Red. Tee
TRE-16
Conc. Red.
REDC-04
Ecc. Red.
REDE-04
Cap
TAM-25
Cross
CRUZ-19
Weldolet
WOL-04
Gate (Note 3)
1/2" - 4"
BW/PLAIN
Wall
thickness
according to
pipe
2" - 24"
1/2" - 1 1/2"
VG-52
2" - 8"
VG-20
10" - 24"
VG-21
BW
Globe
2" - 10"
1/2" - 1 1/2"
VR-83
2" - 24"
VR-43
1/2" - 1 1/2"
VGL-11
Check
Flange
(Note 5)
FLG-54
1/2" - 1 1/2"
FLG-53
1/2" - 24"
FLG-52
2" - 24"
JE-07
1/2" - 3"
JE-08
4" - 6"
JE-09
8" - 24"
JI-01
1/2" - 24"
Other
WN (RF)
RF
Stud
(Note 11)
Nut
BLIND (RF)
0,175" (4,4mm)
Gasket
(Note 10)
SW (RF)
300
1/2" - 1 1/2"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-26
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
44 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-46C/149C
________
300
C3
up to 38
600
50
580
100
504
110
494
149
456
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 For onshore facilities only, stub in connections may be used according to ASME B31.3.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
4 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
6 Use only downstream centrifuge.
7 Use only downstream filters.
8 Use according appendix 5.
9 When requerid Fully Tight valve (VET), see types in appendix 14.
10 Isolating joint see drawing on the appendix 15.
11 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
45 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
ASME B31.3
0C / 350C
(1,6 mm)
Tag
T-05A
Size
(in)
Wall or
Class
1/2" - 1 1/2"
Sch 80
Valves
C4
Material
Ball
PLAIN
Size
Description
1/2" - 1 1/2"
VG-45
2" - 8"
VG-07
10" - 24"
VG-07A
2" - 12"
1/2" - 1 1/2"
Tag
API 5L Gr B PSL 1
seamless or
welded (E=0,95)
Sch 40
BW
T-02B
(Notes 1 and 4)
300
(Note 6)
2" - 14"
Standard
Ends
T-02A
Pipe
Class
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Cap
TAM-05
Red. Coupling
LRE-01
Coupling
L-04
Union
UN-04
Short Nip.
16" - 20"
22"
0,625
24"
Sch 40
3000
API 5L Gr B PSL 1
welded (E=0,95)
SW
ASTM A 105
1/2" - 1 1/2"
Gate
PLAIN
T-05A
Long Nip.
Red.Nip.C
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
1/2" - 4"
PLAIN/BW
Wall
thickness
according to
pipe
Globe
2" - 24"
BW
VGL-05
ASTM A 105
Check
2" - 24"
2" - 24"
VR-56
VR-97
VR-96
Other
1/2" - 1 1/2"
FLG-41A
Flange
(Note 5)
Gasket
Stud
Nut
1/2" - 1 1/2"
FLG-10A
2" - 24"
FLG-11A
1/2" - 24"
JE-07
1/2" - 3"
JE-08
4" - 6"
JE-09
8" - 24"
SW (RF)
300
WN (RF)
ASTM A 105
BLIND (RF)
0,175"
(4,4mm)
(Note 2)
1/2" - 1 1/2"
ASTM A194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
46 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 350C
(1,6 mm)
300
C4
Temp. (C)
up to 38
741
300
577
50
726
350
545
100
675
150
654
200
635
250
607
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
6 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
47 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
ASME B31.3
0C / 90C
(3,2mm)
Ends
T-05A
3/4"
XXS
PLAIN
Pipe
T-02A
2" - 6"
Sch 80
BW
Half Coupling
6000
SW
ASTM A 105
Short Nip.
XXS
PLAIN
Wall
thickness
according to
pipe
BW
Tag
Standard
300
C5
Valves
Size
(in)
Item
Class
Material
Ball
Size
Description
Tag
3/4"
VE-48D
2 1/16" - 4 1/16"
ML-03
3/4"
T-05A
Long Nip.
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
2" - 6"
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
ASTM A 105
Gate
(Note 4)
VG ABRAS-04
Globe
Check
2" - 6"
Other
Flange
(Note 4)
FLG-10A
2" - 6"
300
WN (RF)
FLG-13
2" - 4"
600
WN (RTJ)
JPH-11
2" - 6"
1/16" (1,6mm)
RF
Compressed non-asbestos
(aramida fiber and NBR)
JA-01
2" - 4"
600
Oval
Gasket
(Note 2)
Stud
Nut
ASTM A 105
ASTM A 193 Gr B7
(Note 2)
5/8" - 3/4"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VR-36
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
48 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
TITLE:
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 90C
(3,2mm)
300
C5
up to 38
741
50
726
90
665
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 In VG ABRAS-04 assembly use FLG-13 (RTJ) flange.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
(Note 6)
ASME B31.3
49 of 134
Temp.
Range
Corrosion
Allowance
Class
Standard
-46C / 110C
(1,6mm)
300
C6
Tag
T-09
Size
(in)
Wall or
Class
1/2" - 3/4"
Sch 160
1" - 1 1/2"
Valves
Ends
PLAIN
Sch 80
Size
Description
Tag
1/2" - 3/4"
VE-91C
1" - 1 1/2"
VE-91B
2" - 4"
VE-08
6" - 24"
VE-09
T-07A
4" - 14"
(Note 8)
Ball
2" - 3"
Pipe
Material
BW
Sch 40
(Notes 1 and 5)
T-08
Elbow 90
JO-17
Elbow 90
JO-18
Equal Tee
TE-12
Red. Tee
TRE-08
Cross
CRUZ-12
Half Coupling
ML-07
Red. Coupling
LRE-04
Cap
TAM-12
Union
UN-09
Coupling
L-09
Elbow 90
JO-13
Elbow 45
JO-14
Equal Tee
TE-09
Red. Tee
TRE-05
Cross
CRUZ-09
Half Coupling
ML-05
Red. Coupling
LRE-03
Cap
TAM-09
Union
UN-07
Coupling
L-08
Short Nip.
Red.Nip.C
NIPRE-16
Red.Nip.C
NIPRC-05A
Red .Nip.E
NIPRE-16A
S.R.ELL 90
CRC-02
L.R.ELL 90
CRL-03
L.R.ELL 45
CRL-04
Tee
TE-08
Red. Tee
TRE-04
Conc. Red.
REDC-02
Ecc. Red.
REDE-02
Cap
TAM-08
Cross
CRUZ-08
Weldolet
WOL-02
Stud
Nut
1/2" - 1 1/2"
6000
1/2" - 3/4"
Gate
SW
1" - 1 1/2"
3000
Globe
2" - 10"
1/2" - 1 1/2"
VGL-23
PLAIN
1/2" - 4"
BW/PLAIN
NIPRC-05
Red .Nip.E
Gasket
1/2" - 3/4"
T-09
Long Nip.
Flange
(Note 7)
16" - 24"
2" - 24"
BW
2" - 24"
FLG-46
1/2" - 1 1/2"
FLG-24
2" - 24"
FLG-25
1/2" - 24"
JE-07
1/2" - 3"
JE-08
4" - 6"
JE-09
8" - 24"
(Note 2)
Check
Wall
thickness
according to
pipe
5/8" - 1 1/2"
WN (RF)
BLIND (RF)
0,175"
(4,4mm)
VR-54
VR-79
(Note 4)
Other
SW (RF)
300
VR-52
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-21
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
50 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-46C / 110C
(1,6mm)
300
C6
-46/38
746
50
726
100
675
110
671
Branch Connections
Temp. (C)
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-07 or TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46C / -15C).
7 Flanges 1 1/2" may be used, if strictly necessary.
8 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
51 of 134
CODE
Service (Note 1)
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-18C / 54C
____
300
C8
Tag
T-05A
Pipe
(Note 2 e 4 )
T-02A
Size
(in)
(Notes 2 and 5)
Wall or
Ends
Class
1/2" - 1 1/2"
PLAIN
Sch 80
2" - 8"
BW
T-02B
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Red. Coupling
LRE-01
Cap
TAM-05
Union
UN-04
Coupling
L-04
Short Nip.
3000
SW
Valves
Material
API 5L Gr B PSL 1 seamless
(Note 2)
API 5L Gr B PSL 1
welded or seamless
(Note 2)
Ball
Size
Description
Tag
1/2" - 1 1/2"
VE-01
ASTM A105
(Note 2)
1/2" - 1 1/2"
T-05A
Long Nip.
PLAIN
Red. Nip. C
NIPRC-04
Red. Nip. E
NIPRE-10
Red. Nip. C
NIPRC-04A
Red. Nip. E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRC-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
BW/PLAIN
1/2" - 4"
Gate
Wall
thickness
according to
pipe
2" - 8"
BW
Globe
Check
1/2" - 1 1/2"
Other
Flange
(Note 2)
Gasket
Stud
Nut
FLG-10A
FLG-11A
300
1" - 8"
JPH-11
WN (RF)
BLIND (RF)
1/16" (1,6mm)
RF
ASTM A105
(Note 2)
Compressed non-asbestos
(aramida fiber and NBR)
ASTM A 193 Gr B7
(Note 3)
1/2" - 7/8"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VR-01
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
52 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
CODE
Service (Note 1)
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-18C / 54C
____
300
C8
-18 to 38
741
54
722
Temp.(C)
Branch Connections
Notes
1 This Spec shall be applied for distribution system of CO2, after directional valves.
2 Pipes, connections and fittings shall be galvanized according ASTM A123, after fabrication of the pipe spool.
3 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
4 From -18C to 0C material must be normalized.
5 When manufactured news header or sections of header, shall be desing avoid weld in support of header.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
53 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 240C
(Note 12)
(3,2mm)
300
C9
Tag
Size
(in)
Wall or Class
1/2" - 3/4"
XXS
T-05A
Ends
Material
Ball
(Note 4)
Size
Description
Tag
1/2" - 3/4"
VE-333D
1" - 1 1/2"
VE-333B
2" - 4"
6" - 24"
VE-319
1/2" - 3/4"
VE-305D
1" - 1 1/2"
VE-305B
2" - 4"
6" - 24"
VE-357
1/2" - 3/4"
VE-48D
1" - 1 1/2"
VE-48B
2" - 4"
6" - 24"
VE-70
1/2" - 3/4"
VE-337D
1" - 1 1/2"
VE-337B
2" - 4"
PLAIN
1" - 1 1/2"
Sch 80
2" - 8"
T-02A
10"
Sch 60
12" - 18"
Pipe
T-02B
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Half Coupling
ML-03
Red. Coupling
LRE-02
Cap
TAM-06
Union
UN-05
Coupling
L-05
20"
0.750"
22"
0.812"
24"
0.875"
26"
0.938"
28"
1.000"
30" - 32"
1.062"
BW
API 5L Gr B PSL 1 welded
(E=0,85)
1/2" - 3/4"
1/2" - 1 1/2"
6000
(Notes 1 and 7)
1/2" - 3/4"
SW
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Red. Coupling
LRE-01
Cap
TAM-05
1" - 1 1/2"
Union
UN-04
Coupling
L-04
API 5L Gr B
PSL 1 seamless
T-05A
Long Nip.
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
6" - 24"
PLAIN
1/2" - 1 1/2"
Red.Nip.C
1/2" - 3/4"
1/2" - 4"
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
BW/PLAIN
1" - 1 1/2"
2" - 4"
6" - 24"
2" - 24"
Wall
thickness
according to
pipe
VE-318
VE-343
VE-344
ASTM A 105
3000
Short Nip.
VE-316
VE-51
VE-69
VE-358
VE-359
VE-360
VE-309D
VE-309B
VE-361
VE-362
VE-363
BW
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
2" - 32"
Gate
1/2" - 1 1/2"
(Note 8)
Gasket
(Notes 9 and 10)
Stud
Nut
VG-45
2" - 8"
VG-05
10" - 24"
VG-06
WN (RF)
Globe
BLIND (RF)
2" - 10"
VGL-04
1/2" - 1 1/2"
VR-56
SW (RF)
FLG-10A
Flange
1/2" - 1 1/2"
ASTM A 105
FLG-41A
WN (RF)
2" - 24"
FLG-11A
300
FLG-10C
FLG-11C
26" - 32"
JPH-11
1/2" - 10"
1/16" (1,6mm)
JPH-12
12" - 32"
1/8" (3,2mm)
JE-07
1/2" - 3"
BLIND (RF)
4" - 6"
JE-09
8" - 24"
0,175" (4,4mm)
JE-10
26" - 32"
JI-03
1/2" - 24"
1/8" (3,2mm)
ASTM A 105
Compressed non-asbestos
(aramida fiber and NBR)
RF
JE-08
(Note 5)
2" - 24"
2" - 24"
(Notes 2)
1/2" - 2"
ASTM A 193 Gr B7
(Notes 2 and 4)
1/2" - 2"
(Notes 2)
1/2" - 2"
ASTM A 194 Gr 2H
(Notes 2 and 4)
1/2" - 2"
ASTM A 194 Gr 7
VR-36
VR-29
Other
1/2" - 1 1/2"
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
54 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 240C
(Note 12)
(3,2mm)
300
C9
up to 38
741
50
726
100
675
110
671
240
613
Temp. (C)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A 194 Gr 7
nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
a) The maximun hardness of any compnent of these especifications should be 22 RC (239 Brinell) according NACE MR0175.
b) The materials should be have a thermic treatment after welding.
c) The bolts (including valves bolts) should be used according norm NACE MR0175.
7 Use niple THD X BW and threaded cap (TAM-01 or TAM-15) after drains and vents blocking.
8 Flanges 1 1/2" may be used, if strictly necessary.
9 For temperature betwen 110 C to 240C, use Spiral-Wound Gasket.
10 Isolating joint see drawing on the appendix 15.
11 When requerid Fully Tight valve (VET), see types in appendix 14.
12 In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of standard ASME
B31.3.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
55 of 134
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
BG-Inert Gas; CI-Chemical Injection (Non-Corrosive); W-Industrial Water (Fresh, NonCorrosive / De-Aerated Sea Water); IW-Fresh And De-Aerated Sea Water Injection (Note
9); G-Glycol; SN- Start-up Nitrogen; SA-Service Compressed Air (Utility Air); P-Process
(non-corrosive hydrocarbon); D-Diesel (Note 8); FG-Fuel Gas (Note 10); AM-Amine
(Note 15).
0C / 240C
(Note 16)
(1,6mm)
300
C10
Tag
T-05A
Size
(in)
Wall or Class
1/2" - 3/4"
Sch 160
1" - 1 1/2"
Pipe
T-02A
T-02B
Ends
API 5L Gr B PSL 1
seamless
2" - 3"
Sch 40
2" - 3"
Sch 80
4" - 10"
Ball
Size
PLAIN
Sch 80
4" - 10"
1/2" - 3/4"
1" - 1 1/2"
BW
API 5L Gr B PSL 1
welded (E=0,85)
Sch 40
2" - 4"
12" - 24"
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Half Coupling
ML-03
Red. Coupling
LRE-02
Cap
TAM-06
Union
UN-05
Coupling
L-05
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Red. Coupling
LRE-01
Cap
TAM-05
Union
UN-04
Coupling
L-04
Short Nip.
6" - 24"
1/2" - 3/4"
1/2" - 3/4"
1/2" - 1 1/2"
1" - 1 1/2"
6000
2" - 4"
1/2" - 3/4"
SW
1" - 1 1/2"
API 5L Gr B PSL 1
seamless
1/2" - 1 1/2"
Red.Nip.C
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
2" - 24"
CRUZ-02
Weldolet
WOL-01
1/2" - 1 1/2"
FLG-10A
2" - 24"
FLG-11A
1/2" - 24"
JPH-11
1/2" - 10"
1/16" (1,6mm)
JPH-12
12" - 24"
1/8" (3,2mm)
JE-07
1/2" - 3"
JE-09
JI-03
Stud
(Notes 2)
4" - 6"
(Notes 2)
(Notes 2 and 4)
VE-344
VE-48B
2" - 4"
6" - 24"
1" - 1 1/2"
2" - 4"
VE-51
VE-69
VE-70
VE-325C
VE-337B
VE-358
VE-359
VE-360
VE-317C
VE-309B
VE-361
VE-362
VE-363
300
1/2" - 24"
WN (RF)
1/2" - 1 1/2"
VG-45
2" - 8"
VG-05
10" - 24"
VG-06
Globe
ASTM A 105
BLIND (RF)
2" - 10"
Compressed non-asbestos
(aramida fiber and NBR)
RF
1/2" - 1 1/2"
ASTM A 193 Gr B7
Other
Stainless steel AISI 304 with flexiblegraphite, with inner ring AISI 304
2" - 24"
1/2" - 1 1/2"
ASTM A 194 Gr 2H
1/2" - 1 1/2"
1/2" - 1 1/2"
ASTM A 194 Gr 7
VGL-04
Check
0,175" (4,4mm)
1/8" (3,2mm)
(Note 5)
SW (RF)
8" - 24"
(Notes 2 and 4)
Nut
VE-343
ASTM A 105
FLG-41A
Gasket
JE-08
(Notes 11 and 12)
VE-305B
1" - 1 1/2"
Gate
Flange
(Note 7 e 14)
VE-321C
VE-48C
6" - 24"
Cross
VE-319
6" - 24"
BW
VE-318
1/2" - 3/4"
Wall
thickness
according to
pipe
VE-316
1/2" - 3/4"
2" - 4"
BW/PLAIN
VE-333B
VE-357
PLAIN
1/2" - 4"
VE-341C
6" - 24"
1/2" - 3/4"
T-05A
Long Nip.
Tag
ASTM A 105
3000
(Note 4)
Description
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VR-56
VR-36
VR-29
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
56 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
BG-Inert Gas; CI-Chemical Injection (Non-Corrosive); W-Industrial Water (Fresh, NonCorrosive / De-Aerated Sea Water); IW-Fresh And De-Aerated Sea Water Injection (Note
9); G-Glycol; SN- Start-up Nitrogen; SA-Service Compressed Air (Utility Air); P-Process
(non-corrosive hydrocarbon); D-Diesel (Note 8); FG-Combustible Gas (Note 10);
AM-Amine (Note 15).
0C / 240C
(Note 16)
(1,6mm)
300
C10
-15 to 38
740
50
726
100
675
240
613
Temp. (C)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grage B16 stud
bolts and ASTM A 194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-01 or TAM-15) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 Use only upstream centrifuge.
9 Use only in onshore installations.
10 Use only upstream filters.
11 For temperature betwen 110 C to 240C, use Spiral-Wound Gasket.
12 Isolating joint see drawing on the appendix 15.
13 When requerid Fully Tight Valve (VET), see types in appendix 14.
14 Onshore instalation use DN 2" and 3" sch 40.
15 For use booster pump discharge.
16 In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of B31.3
standard ASME.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
A
SHEET:
E&P
TITLE:
1 of 2
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
PCW-Produced water
0C / 120C
___
300
C11
Pipes and Fittings (Organic coating - according appendix 18) (Notes 7 and 8)
Item
Tag
T-05A
T-02A
Pipe
T-02B
Size
(in)
1" - 1 1/2"
Wall or Class
Sch 80
Ends
PLAIN
API 5L Gr B PSL 1
seamless
2" - 3"
4" - 14"
Sch 40
2" - 3"
Sch 80
4" - 16"
Sch 40
Material
Ball
Size
Description
Tag
1" - 1 1/2"
VE-201
2" - 4"
BW
API 5L Gr B PSL 1 welded
(E=0,85)
6" - 16"
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Red. Coupling
LRE-01
Cap
TAM-05
Union
UN-04
Coupling
L-04
Short Nip.
2" - 4"
1" - 1 1/2"
6" - 16"
3000
T-05A
Long Nip.
Red.Nip.C
1" - 1 1/2"
VE-193
VE-195
VE-197
VE-205
VE-206
VE-207
VE-208
PLAIN
1" - 4"
BW/PLAIN
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Wall
thickness
according to
pipe
2" - 16"
Gate
1" - 1 1/2"
VG-85
2" - 8"
VG-81
10" - 16"
VG-82
BW
(Note 4)
Ecc. Red.
REDE-01
Globe
Cap
TAM-02
2" - 10"
Cross
CRUZ-02
1"- 1 1/2"
VR-117
2" - 16"
VR-115
1" - 1 1/2"
Weldolet
VGL-45
ASTM A 105
WOL-01
Check
FLG-10A
1" - 16"
FLG-11A
1" - 16"
Gasket
(Note 6)
Stud
Nut
WN (RF)
JP-01
1" - 10"
1/16" (1,6mm)
JP-02
16"
1/8" (3,2mm)
JI-03
1" - 16"
1/8" (3,2mm)
300
Flange
(Notes 2)
(Notes 2 and
10)
(Notes 2)
(Notes 2 and
10)
ASTM A 105
BLIND (RF)
RF
PTFE Expanded
Other
1/2" - 1 1/2"
ASTM A 193 Gr B7
1/2" - 1 1/2"
1/2" - 1 1/2"
ASTM A 194 Gr 2H
1/2" - 1 1/2"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-31
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
A
SHEET:
E&P
TITLE:
2 of 2
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
PCW-Produced water
0C / 120C
___
300
C11
To 38
740
50
726
100
675
120
667
Temp. (C)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use niple THD X PLAIN and threaded cap (TAM-01 or TAM-15) after drains and vents blocking.
6 Isolating joint see drawing on the appendix 15.
7 Onshore instalation use DN 2" and 3" sch 40.
8 All pipes shall be organic coated according appendix 18.
9 When requerid Fully Tight valve (VET), see types in appendix 14.
10 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and ASTM A 194
Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
57 de 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
TITLE:
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 140C
(Note 11)
_______
300
C12
CODE
ASME B31.3
Tag
T-17
T-19
Size
(in)
1/2" - 1 1/2"
Wall or Class
Sch 40S
Ends
Material
PLAIN
2" - 8"
Sch 10S
Pipe
10" - 12"
(Notes 1 and 3)
T-20
Elbow 90
JO-29
Elbow 45
JO-30
Equal Tee
TE-18
Red. Tee
TRE-13
Cross
CRUZ-18
Half Coupling
ML-12
BW
Sch 40S
22"
0,312"
24"
Sch 40S
3000
Size
Description
Tag
1/2" - 1 1/2"
VE-354
2" - 4"
VE-367
6" - 24"
VE-368
1/2" - 1 1/2"
VE-364
2" - 4"
VE-369
6" - 24"
VE-370
1/2" - 1 1/2"
VG-51
2" - 8"
VG-57
10" - 24"
VG-58
2" - 10"
SW
ASTM A 182 Gr F 55
(UNS S32760)
1/2" - 1 1/2"
UN-15
Coupling
L-16
ASTM A 790 (UNS S32760)
seamless
T-17
Long Nip.
Ball
TAM-22
Union
Short Nip.
14" - 20"
(Note 7)
PLAIN
Red.Nip.C
NIPRC-09
Red .Nip.E
NIPRE-15
Red.Nip.C
NIPRC-09A
Red .Nip.E
NIPRE-15A
S.R.ELL 90
CRC-06
L.R.ELL 90
CRL-13
L.R.ELL 45
CRL-14
Tee
TE-25
Red. Tee
TRE-19
Conc. Red.
REDC-07
Ecc. Red.
REDE-07
Cap
TAM-27
Cross
CRUZ-21
Weldolet
WOL-05
Gate
1/2" - 4"
(Note 2)
BW/PLAIN
Wall
thickness
according to
pipe
2" - 24"
BW
Globe
VGL-38
ASTM A 182 Gr F 55
(UNS S32760)
Check
1/2" - 1 1/2"
2" - 24"
VR-87
VR-73
Other
1/2" - 1 1/2"
Flange
(Note 4)
FLG-105
1/2" - 1 1/2"
FLG-104
1/2" - 24"
FLG-103
Stud
2" - 24"
1/16" (1,6mm)
JPH-12
12" - 24"
1/8" (3,2mm)
JE-07
1/2" - 3"
4" - 6"
JE-09
8" - 24"
JI-03
1/2" - 24"
ASTM A 182 Gr F 55
(UNS S32760)
Compressed non-asbestos
(aramida fiber and NBR)
RF
0,175" (4,4mm)
1/8" (3,2mm)
(Notes 12)
(Notes 2)
(Notes 12 and
13)
BLIND (RF)
WN (RF)
1/2" - 10"
Nut
SW (RF)
300
JPH-11
Gasket
JE-08
(Notes 6 and 9)
1/2" - 1 1/2"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-28
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
58 of 134
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 140C
(Note 11)
_______
300
C12
CODE
ASME B31.3
SHEET:
up to 38
749
50
749
100
735
120
707
140
665
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
3 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
4 Flanges 1 1/2" may be used, if strictly necessary.
5 Use according appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According appendix 16 - Welding qualification requirements for superduplex.
8 According appendix 17 - Casting qualification requirements minimum for valves superduplex.
9 For temperature over 110C, use spiral gaskets.
10 When requerid Fully Tight valve (VET), see types in appendix 14.
11 In possibility of occurrence of low temperatures up to -46C, this spec can be used in accordance with table A-1 of ASME B31.3
standard.
12 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
13 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
59 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
This SPEC shall be used only repair, when the plant material was designed in
according to (UNS S32750). For new project use espec C12 (UNS S32760).
0C / 120C
(Note 8)
_______
300
C13
Tag
T-13
Pipe
T-15
Size
(in)
1/2" - 1 1/2"
Wall or Class
Sch 40S
(Notes 1 and 3)
T-16
Elbow 90
JO-27
Elbow 45
JO-28
Equal Tee
TE-17
Red. Tee
TRE-12
Cross
CRUZ-17
PLAIN
10" - 24"
3000
Size
Description
Tag
1/2" - 1 1/2"
VE-74
2" - 4"
VE-78
6" - 24"
VE-79
SW
1/2" - 1 1/2"
VG-50
2" - 8"
VG-57
10" - 24"
VG-58
2" - 10"
1/2" - 1 1/2"
VR-86
2" - 24"
VR-73
1/2" - 1 1/2"
1/2" - 1 1/2"
TAM-21
Union
UN-14
Coupling
L-15
Gate
T-13
Long Nip.
Red.Nip.C
Ball
BW
Short Nip.
Material
2" - 8"
Sch 10S
Valves (Note 7)
Ends
PLAIN
NIPRC-08
Red .Nip.E
NIPRE-14
Red.Nip.C
NIPRC-08A
Red .Nip.E
NIPRE-14A
S.R.ELL 90
CRC-05
L.R.ELL 90
CRL-11
L.R.ELL 45
CRL-12
Tee
TE-24
Red. Tee
TRE-18
Conc. Red.
REDC-06
Ecc. Red.
REDE-06
Cap
TAM-26
Cross
CRUZ-20
Weldolet
WOL-06
(Note 2)
BW/PLAIN
1/2" - 4"
Wall
thickness
according to
pipe
2" - 24"
(Note 7)
ASTM A 815
(UNS S32750)
Globe
BW
VGL-38
Check
Other
Flange
(Note 4)
FLG-102
1/2" - 1 1/2"
FLG-101
1/2" - 24"
FLG-100
Gasket
(Note 5)
Stud
Nut
SW (RF)
300
2" - 24"
JPH-11
1/2" - 10"
JPH-12
12" - 24"
JI-03
1/2" - 24"
BLIND (RF)
WN (RF)
1/16" (1,6mm)
RF
Compressed non-asbestos
(aramida fiber and NBR)
1/8" (3,2mm)
Fenolic resin with neoprene
(Notes 9)
ASTM A 193 Gr B7
(Notes 9 and
10)
(Notes 9)
ASTM A 194 Gr 2H
(Notes 9 and
10)
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-29
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
60 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
This SPEC shall be used only repair, when the plant material was designed in
according to (UNS S32750). For new project use espec C12 (UNS S32760).
0C / 120C
(Note 8)
_______
300
C13
up to 38
749
50
749
100
735
120
707
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
3 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
4 Flanges 1 1/2" may be used, if strictly necessary.
5 Isolating joint see drawing on the appendix 15.
6 According appendix 16 - Welding qualification requirements for superduplex.
7 According appendix 17 - Casting qualification requirements minimum for valves superduplex.
8 In possibility of occurrence of low temperatures up to -29C, this spec can be used in accordance with table A-1 of ASME B31.3 standard.
9 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
10 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A
194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
61 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
ASME B31.3
IW-Fresh And De-Aerated Sea Water Injection (Note 2); SW-Aerated Sea Water
(Note 3)
0C / 70C
_____
Tag
T-05A
Size
(in)
Wall or Class
1" - 1 1/2"
T-02A
Material
PLAIN
API 5L Gr B PSL 1
seamless
2" - 3"
T-02B
Pipe
(Note 8)
T-02A
BW
4" - 10"
26" - 32"
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Ball
Tag
1" - 1 1/2"
VE-45
2" - 4"
6" - 24"
VE-23E
26" - 32"
VE-23F
2" - 8"
Red. Coupling
LRE-01
VG-05B
Cap
TAM-05
Union
UN-04
10" - 24"
VG-06A
Coupling
L-04
Short Nip.
26" - 32"
VG-06B
2" - 10"
1" - 1 1/2"
VR-93
2" - 24"
VR-65
26" - 32"
VR-65A
1" - 1 1/2"
Sch 20
3000
VE-18E
VE-11E
Gate
ASTM A 105
1" - 1 1/2"
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
Red.Nip.C
SW
C14
Description
API 5L Gr B PSL 1
welded (E=0,85)
12" - 24"
300
Size
Sch 40
T-02B
Standard
Valves
Ends
Sch 80
Class
PLAIN
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
1" - 4"
BW/PLAIN
2" - 24"
Wall
thickness
according to
pipe
Red. Tee
TRE-01
Conc. Red.
REDC-01
Globe
ASTM A 234 Gr WPB
VGL-04B
BW
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
2" - 32"
ASTM A 105
Check
FLG-10B
1" - 1 1/2"
WN (FF)
2" - 24"
FLG-11B
Flange
(Notes 6 and 8)
BLIND (FF)
300
FLG-09C
FLG-10D
26" - 32"
BLIND (FF)
FLG-09D
Stud
Nut
SO (FF)
ASTM A 105
WN (FF)
FLG-11D
Gasket
(Note 4)
Other
WN (FF)
FLG-10B
SO (FF)
JPH-13
1" - 10"
1/16" (1,6mm)
JPH-14
12" - 32"
1/8" (3,2mm)
FF
Compressed non-asbestos
(aramida fiber and NBR)
ASTM A 193 Gr B7
(Note 7)
5/8" - 1 7/8"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-08
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
62 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
IW-Fresh And De-Aerated Sea Water Injection (Note 2); SW-Aerated Sea Water
(Note 3)
0C / 70C
_____
300
C14
up to 38
741
50
726
70
706
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use only in offshore installations.
3 Use when the metalic material is required by classifier.
4 Isolating joint see drawing on the appendix 15.
5 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
6 Flanges 1 1/2" may be used, if strictly necessary.
7 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
8 Piping, conections and fittings should be revested with polyethylene according appendix 13.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 130C
(Note 11)
_______
300
C16
Tag
T-36
T-37A
Size
(In)
1/2" - 1 1/2"
Wall or Class
SCH 40S
(Note 7)
Ends
Material
PLAIN
ASTM A 790 (UNS S31803)
seamless
2" - 8"
Ball
Size
Description
Tag
1/2" - 1 1/2"
VE-209
2" - 4"
VE-216
6" - 24"
VE-217
1/2" - 1 1/2"
VE-212
2" - 4"
VE-219
6" - 24"
VE-220
1/2" - 1 1/2"
VG-88
2" - 8"
VG-92
10" - 24"
VG-93
2" - 10"
1/2" - 1 1/2"
VR-119
2" - 24"
VR-122
1/2" - 1 1/2"
SCH 10S
Pipe
10"
(Notes 1 and 3)
T-37B
Elbow 90
JO-45
Elbow 45
JO-46
Equal Tee
TE-38
Red. Tee
TRE-33
Cross
CRUZ-32
12" - 20"
BW
SCH 40S
22"
SCH 20
24"
SCH 40S
3000
SW
TAM-35
Union
UN-23
Coupling
L-27
Short Nip.
ASTM A 182 Gr F 51
(UNS S31803)
1/2" - 1 1/2"
T-36
Long Nip.
PLAIN
Red.Nip.C
NIPRC-11
Red .Nip.E
NIPRE-18
Red.Nip.C
NIPRC-11A
Red .Nip.E
NIPRE-18A
S.R.ELL 90
CRC-22
L.R.ELL 90
CRL-30
L.R.ELL 45
CRL-31
Tee
TE-39
Red. Tee
TRE-34
Conc. Red.
REDC-15
Ecc. Red.
REDE-14
Cap
TAM-36
Cross
CRUZ-33
Weldolet
WOL-07
1/2" - 4"
Gate
(Note 2)
BW/PLAIN
Wall
thickness
according to
pipe
2" - 24"
BW
Globe
VGL-84
ASTM A 182 Gr F 51
(UNS S31803)
Check
Other
Flange
(Note 4)
FLG-123
1/2" - 1 1/2"
FLG-124
1/2" - 24"
FLG-125
2" - 24"
1/2" - 10"
1/16" (1,6mm)
JPH-12
12" - 24"
1/8" (3,2mm)
JE-07
1/2" - 3"
4" - 6"
JE-09
8" - 24"
JI-03
1/2" - 24"
(Note 12)
(Notes 12 and
1/2" - 1 1/2"
13)
Nut
BLIND (RF)
ASTM A 182 Gr F 51
(UNS S31803)
WN (RF)
JPH-11
Gasket
JE-08
(Notes 6 and 9)
Stud
SW (RF)
300
Compressed non-asbestos
(aramida fiber and NBR)
RF
0,175" (4,4mm)
1/8" (3,2mm)
(Notes 12)
ASTM A 194 Gr 2H
(Notes 12 and
13)
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-35
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 130C
(Note 11)
_______
300
C16
CODE
ASME B31.3
up to 38
749
50
749
100
735
110
721
130
693
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves shall be used.
3 Use niple THD X PLAIN and threaded cap (TAM-37) after drains and vents blocking.
4 Flanges 1 1/2" may be used, if strictly necessary.
5 Use according appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According appendix 16 - Welding qualification requirements for superduplex and duplex steel.
8 According appendix 17 - Casting qualification requirements minimum for valves superduplex and duplex steel.
9 For temperature over 110C, use spiral gaskets.
10 When requerid Fully Tight valve (VET), see types in appendix 14.
11 In possibility of occurrence of low temperatures up to -46C, this spec can be used in accordance with table A-1 of ASME B31.3
standard.
12 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
13 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
14 Use this Spec after the first Production Separator to the PC service.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
1 of 2
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 150C
(Note 11)
___
300
C30
Pipes and Fittings (Coated with Inconel 625 - According appendix 21) (Note 9)
Item
Tag
T-05A
T-02A
or
T-02B
Pipe
T-02B
(Notes 1 and 6)
Equal Tee
TRE-35
Cross
CRUZ-34
Half Coupling
ML-19
Red. Coupling
LRE-17
Cap
TAM-39
Union
UN-24
Coupling
L-28
1 1/2"
2"
3"
4"
6"
8"
SCH 20 0,250"
10"
SCH 20 0,250"
12"
0,281"
14"
SCH 20 0,312"
16"
SCH 30 0,375"
18"
0,406"
20"
0,438"
24"
SCH 30 0,562"
Ends
Ball
Description
Tag
1" - 1 1/2"
VE-463
2" - 4"
BW
API 5L Gr B PSL 1
seamless
or
API 5L Gr B PSL 1
welded (E=0,95)
(Note 4)
Size
6" - 24"
VE-464
VE-465
VE-466
API 5L Gr B PSL 1
welded (E=0,95)
1" - 1 1/2"
ASTM A 105
API 5L Gr B PSL 1
seamless
1" - 1 1/2"
Red. Nip. C
NIPRC-04
Red. Nip. E
NIPRE-10
Red. Nip. C
NIPRC-04A
Red. Nip. E
NIPRE-10A
1" - 4"
Wall
thickness
according to
pipe
BW
ASTM A 234 Gr WPB
C903D-01 (90)
Gate
API 5L Gr B PSL 1
seamless
C453D-01 (45)
Tee
Material
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
3D. R. ELBOW
Wall or Class
1"
Valves
TE-41
Red. Tee
Short Nip.
Size
(in)
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
2" - 24"
ASTM A 234 Gr WPB
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01A
ASTM A 105
Butterfly
Globe
Flange
Gasket
(Note 7)
FLG-
1" - 24"
FLG-
1" - 24"
JPH-07
1" - 10"
JPH-08
12" - 24"
JI-01
1" - 24"
300
BLIND (RF)
2" - 12"
1 - 1 1/2"
VR-139
2" - 24"
VR-140
1" - 1 1/2"
ASTM A 105
Check
WN (RF)
1/16" (1,6mm)
RF
Compressed non-asbestos
(aramida fiber and NBR)
VGL-96
1/8" (3,2mm)
Fenolic resin with neoprene
Other
Stud
Nut
(Notes 2)
1/2" - 1 1/2"
ASTM A 193 Gr B7
(Notes 2 and 4)
1/2" - 1 1/2"
(Notes 2)
1/2" - 1 1/2"
ASTM A 194 Gr 2H
(Notes 2 and 4)
1/2" - 1 1/2"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-40
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
2 of 2
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 150C
(Note 11)
___
300
C30
38
Temp. (C)
740
727
100
676
150
654
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and ASTM
A 194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
5 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
6 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
7 Isolating joint see drawing on the appendix 15.
8 When requerid Fully Tight valve (VET), see types in appendix 14.
9 All piping shall be internal Inconel 625 coated according Appendix 21.
10 Use this Spec after choke valve until the arrival of the first Production Separator.
11 In accordance with Table 323.2.2 A of standard ASME B31.3, all pipes shall be normalized.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
D
SHEET:
E&P
TITLE:
63 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-100C /
190C
______
600
E3
Tag
T-11
Fittings
(Notes 1 and 4)
Pipe
T-30
(Note 9)
Elbow 90
JO-23
Elbow 45
JO-24
Equal Tee
TE-15
Red. Tee
TRE-10
Cross
CRUZ-15
Half Coupling
ML-09
Red. Coupling
LRE-05
Cap
TAM-19
Union
UN-12
Coupling
L-13
Short Nip.
Wall or Class
Ends
Material
1/2" - 1 1/2"
Sch 40S
PLAIN
Size
Description
Tag
2" - 4"
Sch 40S
6"
Sch 80S
VE-230
8"
Sch 40S
1/2" - 1 1/2"
BW
10" - 12"
Sch 80
Ball
2" - 4"
6" - 12"
1/2" - 1 1/2"
3000
SW
1/2" - 1 1/2"
6" - 12"
1/2" - 1 1/2"
T-11
Long Nip.
Red.Nip.C
Valves (Note 7)
Size
(in)
2" - 4"
PLAIN
NIPRC-07
Red .Nip.E
NIPRE-13
Red.Nip.C
NIPRC-07A
Red .Nip.E
NIPRE-13A
S.R.ELL90
CRC-04
L.R.ELL 90
CRL-07
L.R.ELL 45
CRL-08
Tee
TE-21
Red. Tee
TRE-16
Conc. Red.
REDC-04
Ecc. Red.
REDE-04
Cap
TAM-25
Cross
CRUZ-19
Weldolet
WOL-04
1/2" - 4"
VE-372
VE-261
VE-262
VE-263
VE-264
VE-265
VE-266
1/2" - 1 1/2"
VE-267
6" - 12"
2" - 12"
VE-371
6" - 12"
BW/PLAIN
Wall
thickness
according to
pipe
BW
Gate
VE-268
VE-269
(Note 3)
1/2" - 1 1/2"
VG-52
2" - 6"
VG-24
8" - 12"
VG-25
2" - 4"
VGL-13
6" - 8"
VGL-13E
1/2" - 1 1/2"
VR-83
2" - 12"
VR-45
Globe
Check
Flange
(Note 5)
Gasket
FLG-57
1/2" - 1 1/2"
FLG-56
1/2" - 12"
FLG-55
2" - 12"
1/2" - 12"
(Notes 10 and
11)
Other
WN (RTJ)
600
Octagonal
1/2" - 1 1/2"
Fenolic resin
JI-04
Nut
BLIND (RTJ)
JA-05
(Note 12)
Stud
SW (RTJ)
600
ASTM A320 Gr L7
1/2" - 1 1/4"
ASTM A194 Gr 4/S3
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-26
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
D
SHEET:
E&P
TITLE:
64 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-100C /
190C
______
600
E3
up to 38
1199
50
1160
100
1013
110
989
150
910
190
858
Temp. (C)
Branch Connections
Temp. (C)
(Note 2)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 For onshore facilities only, stub in connections may be used according to ASME B31.3.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves shall be used.
4 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
6 Use only downstream filters.
7 When requerid Fully Tight valve (VET), see types in appendix 14.
8 For use Gas Inlet and Outlet from Amine Contactors.
9 For -101C to -30C material shall de solution heat treated.
10 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
11 Isolating joint see drawing on the appendix 15.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
65 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 350C
(1,6mm)
600
E4
Tag
T-05A
Size
(in)
1/2" - 1 1/2"
Wall or
Class
Sch 80
Valves
Ends
Material
PLAIN
(Note 6)
Ball
Size
Description
1/2" - 1 1/2"
VG-45
2" - 6"
VG-61
8" - 24"
VG-62
2" - 4"
VGL-34
6" - 8"
VGL-34E
Tag
2"
T-02A
Pipe
3"
Sch 40
4" - 10"
BW
Sch 80
T-02B
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
12" - 24"
3000
SW
ASTM A 105
(Notes 1 and 4)
Cap
Red.Nip.C
NIPRC-04
Fittings
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
1/2" - 1 1/2"
TAM-05
Union
UN-04
Coupling
L-04
Short Nip.
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
PLAIN
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
Gate
1/2" - 4"
BW/PLAIN
Wall
thickness
according to
pipe
BW
2"- 24"
Globe
ASTM A 105
Check
Check valve; horizontal piston; class
1/2" - 1 1/2"
800; SW; carbon steel.
2" - 24"
2" - 24"
Flange
(Note 5)
Gasket
(Note 2)
FLG-42
1/2" - 1 1/2"
FLG-13
2" - 24"
FLG-15
1/2" - 24"
JA-01
1/2" - 24"
Stud
VR-56
VR-99
VR-98
SW (RTJ)
600
WN (RTJ)
ASTM A 105
BLIND (RTJ)
600
Oval
Other
Globe valve, needle disc; 3000 PSI;
1/2" - 1 1/2"
SW; carbon steel.
ASTM A 193 Gr B7
(Note 2)
Nut
1/2" - 1 7/8"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
67 of 134
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 90C
(3,2mm)
600
E5
CODE
ASME B31.3
Tag
T-05A
Pipe
Half Coupling
Short Nip.
T-02A
Valves
Size
(in)
Wall or
Class
Ends
3/4"
XXS
PLAIN
2"
Sch 160
3" - 8"
Sch 80
ML-03
Material
Ball
Size
Description
Tag
3/4"
VE-48D
2 1/16" - 9"
6000
ES
ASTM A 105
XXS
PL
Wall
thickness
according to
pipe
BW
3/4"
T-05A
Long Nip.
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
2" - 8"
ASTM A105
Gate
(Note 4)
VG ABRAS-04
Globe
Check
2" - 8"
Other
Flange
(Note 4)
Gasket
(Note 2)
Stud
Nut
FLG-13
2" - 8"
FLG-15
2" - 8"
JA-01
2" - 8"
600
WN (RTJ)
ASTM A 105
BLIND (RTJ)
600
Oval
(Note 2)
5/8" - 1"
ASTM 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VR-38
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
68 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 90C
(3,2mm)
600
E5
up to 38
1480
50
1453
90
1372
Temp. (C)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gasket must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 In VG ABRAS-04 assembly use FLG-13 (RTJ) flange.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
66 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
350C
(1,6mm)
600
E4
Temp. (C)
up to 38
1480
250
1216
50
1453
300
1154
150
1308
350
1089
200
1270
220
1249
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
6 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
69 of 134
CODE
Service (Note 5)
Temp.
Range
Corrosion
Allowance
ASME B31.3
-46C / 110C
(1,6mm)
Tag
T-09
Size
(in)
1/2" - 3/4"
Valves
Wall or Class
Ends
Sch 160
PLAIN
1" - 1 1/2"
Pipe
T-07A
ASTM A 333 Gr 6
seamless
2" - 3"
Sch 80
(Notes 1 and 6)
Fittings and Accessories
Elbow 90
JO-17
Elbow 45
JO-18
Equal Tee
TE-12
Red. Tee
TRE-08
Cross
CRUZ-12
Half Coupling
ML-07
Red. Coupling
LRE-04
Cap
TAM-12
Union
UN-09
Coupling
L-09
Elbow 90
JO-13
Elbow 45
JO-14
Equal Tee
TE-09
Red. Tee
TRE-05
Cross
CRUZ-09
Half Coupling
ML-05
Red. Coupling
LRE-03
Cap
TAM-09
Union
UN-07
Coupling
L-08
BW
E6
Description
Tag
1/2" - 3/4"
VE-91C
1" - 1 1/2"
VE-91B
2" - 4"
VE-92
6" - 24"
VE-93
1/2" - 3/4"
1/2" - 1 1/2"
6000
1/2" - 3/4"
SW
Gate
1" - 1 1/2"
3000
ASTM A 333 Gr 6
seamless
T-09
Long Nip.
600
(Note 9)
Size
ASTM A 671 Gr CC 60 CL 22
welded (E=1)
16" - 24"
Standard
Ball
4" - 14"
T-08
Short Nip.
Material
Class
1/2" - 1 1/2"
PLAIN
Red.Nip.C
NIPRC-05
Globe
Red .Nip.E
NIPRE-16
2" - 4"
VGL-24
Red.Nip.C
NIPRC-05A
Red .Nip.E
NIPRE-16A
6" - 8"
CRC-02
VGL-24E
S.R.ELL 90
L.R.ELL 90
CRL-03
L.R.ELL 45
CRL-04
Tee
TE-08
Red. Tee
TRE-04
1/2" - 1 1/2"
VR-52
Conc. Red.
REDC-02
2" - 24"
VR-55
2" - 24"
VR-80
(Note 4)
Ecc. Red.
REDE-02
Cap
TAM-08
Cross
CRUZ-08
Weldolet
Flange
(Note 7)
Gasket
(Notes 2 and 8)
1/2" - 4"
Wall
thickness
according to
pipe
2" - 24"
Nut
BW
Check
WOL-02
FLG-47
1/2" - 1 1/2"
FLG-26
2" - 24"
FLG-27
1/2" - 24"
SW (RTJ)
600
WN (RTJ)
1/2" - 24"
(Note 2)
600
Oval
Other
BLIND (RTJ)
JA-03
1/2" - 1 1/2"
Stainless steel AISI 304 max
hardness 150 Brinell
Fenolic resin
JI-04
Stud
BW/PLAIN
1/2" - 1 7/8"
ASTM A 320 Gr L7
ASTM A 194 Gr 4/S3
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-21
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
ASME B31.3
70 of 134
(Note 5)
Temp.
Range
Corrosion
Allowance
Class
Standard
-46C / 110C
(1,6mm)
600
E6
-46/38
1480
50
1453
100
1351
110
1343
Temp. C
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Charpy impact test is required for low temperature services materials (-46C / -15C).
6 Use niple THD X PLAIN and threaded cap (TAM-07 or TAM-16) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 Isolating joint see drawing on the appendix 15.
9 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
TECHNICAL SPECIFICATION
REV:
I-ET-3000.00-1200-200-PCI-001
CLIENT:
E&P
TITLE:
71 of 134
CODE
(Note 5)
ASME B31.3
Temp.
Range
Corrosion
Allowance
-46C / 110C
(1,6mm)
Tag
T-09
Size
(in)
1/2" - 3/4"
1" - 1 1/2"
Wall or
Class
Sch 160
Valves
Ends
T-07A
4" - 8"
Sch 80
ASTM A 333 Gr 6
seamless
Sch 40
Sch 60
(Notes 1 and 6)
Fittings and Accessories
Elbow 90
JO-17
Elbow 45
JO-18
Equal Tee
TE-12
Red. Tee
TRE-08
Cross
CRUZ-12
Half Coupling
ML-07
Red. Coupling
LRE-04
Cap
TAM-12
Union
UN-09
Coupling
L-09
Elbow 90
JO-13
Elbow 45
JO-14
Equal Tee
TE-09
Red. Tee
TRE-05
Cross
CRUZ-09
Half Coupling
ML-05
Red. Coupling
LRE-03
ASTM A 671 Gr CC 60 CL 22
welded (E=1)
16" - 24"
Class
Standard
600
E6R
(Note 9)
Ball
Size
Description
Tag
1/2" - 3/4"
VE-91C
1" - 1 1/2"
VE-91B
2" - 4"
VE-92
6" - 24"
VE-93
BW
10" - 14"
T-08
Material
PLAIN
2" - 3"
Pipe
SHEET:
1/2" - 3/4"
1/2" - 1 1/2"
6000
1/2" - 3/4"
SW
1" - 1 1/2"
Gate
3000
Cap
TAM-09
Union
UN-07
Coupling
L-08
Globe
T-09
2" - 4"
VGL-24
6" - 8"
VGL-24E
1/2" - 1 1/2"
Short Nip.
Long Nip.
Red.Nip.C
NIPRC-05
Red .Nip.E
NIPRE-16
Red.Nip.C
NIPRC-05A
Red .Nip.E
NIPRE-16A
S.R.ELL 90
CRC-02
L.R.ELL 90
CRL-03
L.R.ELL 45
CRL-04
Tee
TE-08
Red. Tee
TRE-04
Conc. Red.
REDC-02
Ecc. Red.
REDE-02
Cap
TAM-08
Cross
CRUZ-08
Weldolet
WOL-02
Flange
(Note 7)
Wall
thickness
according to
pipe
2" - 24"
Check
BW
2" - 24"
2"- 24"
FLG-47
1/2" - 1 1/2"
FLG-26
2" - 24"
FLG-27
1/2" - 24"
1/2" - 24"
(Notes 2 and 8)
WN (RTJ)
VR-55
VR-80
(Note 4)
600
Oval
Other
BLIND (RTJ)
1/2" - 1 1/2"
Stainless steel AISI 304 max
hardness 150 Brinell
ASTM A 320 Gr L7
(Note 2 )
VR-52
SW (RTJ)
600
Fenolic resin
JI-04
Nut
BW/PLAIN
1/2" - 4"
JA-03
Gasket
Stud
PLAIN
1/2" - 1 1/2"
1/2" - 1 7/8"
ASTM A 194 Gr 4/S3
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-21
N:
TECHNICAL SPECIFICATION
REV:
I-ET-3000.00-1200-200-PCI-001
CLIENT:
SHEET:
E&P
TITLE:
72 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
CODE
Service (Note 5)
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-46C / 110C
(1,6mm)
600
E6R
-46/110
1030
Temp. (C)
Notas:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Charpy impact test is required for low temperature services materials (-46C / -15C).
6 Use niple THD X PLAIN and threaded cap (TAM-07 or TAM-16) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 Isolating joint see drawing on the appendix 15.
9 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
73 of 134
TITLE:
CODE
Service (Note 1)
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
DO-Carbon Dioxide
-18C / 54C
_______
600
E8
Tag
T-05A
Size
(in)
1/2" - 1 1/2"
Pipe
(Notes 2 and 4)
Ends
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Red. Coupling
LRE-01
Cap
TAM-05
Union
UN-04
Coupling
L-04
Material
SW
API 5L Gr B PSL 1
seamless (Note 2)
Sch 80
T-02A
Short Nip.
Wall or
Class
Valves
2" - 8"
Ball
Size
Description
Tag
1/2" - 1 1/2"
VE-01
BW
3000
SW
1/2" - 1 1/2"
T-05A
Long Nip.
PLAIN
Red. Nip. C
NIPRC-04
Red. Nip. E
NIPRE-10
Red. Nip. C
NIPRC-04A
Red. Nip. E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRC-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
1/2" - 4"
BW/PLAIN
Gate
Wall thickness
according to
pipe
BW
2" - 8"
Globe
ASTM A 105 (Note 2)
Check
1/2" - 1 1/2"
VR-01
2" - 3"
VR-98
Other
Flange
FLG-13
1" - 8"
600
FLG-15
Gasket
(Note 3)
Stud
Nut
JA-01
WN (RTJ)
BLIND (RTJ)
1" - 8"
600
Oval
(Note 3)
1/2" - 1 1/8"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
74 of 134
CODE
Service (Note 1)
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
DO-Carbon Dioxide
-18C / 54C
_______
600
E8
-18 to 38
1480
54
1445
Temp. (C)
Branch Connections
Notes:
1 This Spec should be applied for distribution system of CO2 before directional valves.
2 Pipes, connections and fittings shall be galvanized according ASTM A123, after fabrication of the pipe spool.
3 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
4 From -18C to 0C material must be normalized.
5 When manufactured news header or sections of header, shall be desing avoid weld in support of header.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
75 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 150C
(Note 11)
(3,2mm)
600
E9
Tag
T-05A
Size
(in)
Wall or
Class
Ends
1/2" - 1 1/2"
XXS
PLAIN
2"
Sch 160
3" - 10"
Sch 80
Material
Ball
Size
1/2" - 1 1/2"
T-02A
Pipe
(Note 11)
BW
2" - 4"
T-02B
12" - 20"
Sch 100
(Notes 1 and 7)
6" - 20"
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Half Coupling
ML-03
Red.
LRE-02
Cap
TAM-06
Union
UN-05
Coupling
L-05
Short Nip.
1/2" - 1 1/2"
2" - 4"
6000
ASTM A 105
6" - 20"
1/2" - 1 1/2"
T-05A
Tag
VE-373D
VE-374
VE-375
VE-376
VE-377D
VE-378
VE-379
VE-380
Long Nip.
SW
(Note 4)
Description
PLAIN
Red.Nip.C
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
1/2" - 4"
BW/PLAIN
Wall
thickness
according to
pipe
2" - 20"
Gate
ASTM A 234 Gr WPB
BW
(Note 5)
1/2" - 1 1/2"
VG-45
2" - 6"
VG-10
8" - 20"
VG-11
2" - 4"
VGL-07
6" - 8"
VGL-07E
1/2" - 1 1/2"
VR-56
2" - 20"
VR-38
Globe
ASTM A 105
Check
Other
Flange
(Note 8)
Gasket
(Notes 2 and 9)
FLG-42
1/2" - 1 1/2"
FLG-13
2" - 20"
FLG-15
1/2" - 20"
Nut
600
WN (RTJ)
1/2" - 20"
1/2" - 1 1/2"
ASTM A 105
600
Oval
1/2" - 1 7/8"
ASTM 193 Gr B7
(Notes 2 and 4)
1/2" - 1 7/8"
(Notes 2)
1/2" - 1 7/8"
ASTM 194 Gr 2H
(Notes 2 and 4)
1/2" - 1 7/8"
ASTM 194 Gr 7
(Notes 2)
BLIND (RTJ)
JA-01
JI-04
Stud
SW (RTJ)
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
76 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 150C
(Note 11)
(3,2mm)
600
E9
up to 38
1480
50
1453
100
1351
110
1343
150
1308
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud bolts and
ASTM A194 GR 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 For PC service, see appendix 5.
7 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
8 Flanges 1 1/2" may be used, if strictly necessary.
9 Isolating joint see drawing on the appendix 15.
10 When requerid Fully Tight valve (VET), see types in appendix 14.
11 In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of standard ASME
B31.3.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
TECHNICAL SPECIFICATION
N:
REV:
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
77 of 134
Service
CODE
BG-Inert Gas; CI-Chemical Injection (Non-Corrosive); W-Industrial Water (Fresh, NonCorrosive / De-Aerated Sea Water); IW-Fresh And De-Aerated Sea Water Injection
0C / 210C
(Note 8); G-Glycol; FG-Fuel Gas (Note 9); P-Process (Non corrosive hydrocarbon);
(Note 12)
AM-Amine (Note 13)
ASME B31.3
Tag
T-05A
Size
(in)
Wall or
Class
1/2" - 3/4"
Sch 160
Ends
PLAIN
API 5L Gr B PSL 1
seamless
T-02A
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Half Coupling
ML-03
Red.
LRE-02
Cap
TAM-06
Union
UN-05
Coupling
L-05
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Red.
LRE-01
Cap
TAM-05
Union
UN-04
Coupling
L-04
Short Nip.
6000
1/2" - 3/4"
VE-381C
1" - 1 1/2"
VE-381B
2" - 4"
6" - 24"
VE-376
1/2" - 3/4"
VE-382C
1" - 1 1/2"
VE-382B
2" - 4"
6" - 24"
1" - 1 1/2"
2" - 4"
6" - 24"
Red.Nip.C
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
Wall
thickness
according to
pipe
2" - 24"
VE-383
VE-384
VE-385
VE-393C
VE-393B
VE-378
VE-379
VE-380
VE-397C
1" - 1 1/2"
VE-397B
6" - 24"
VE-398
VE-399
VE-400
1/2" - 3/4"
VE-401C
1" - 1 1/2"
VE-401B
2" - 4"
6" - 24"
VE-404
1/2" - 3/4"
VE-405C
VE-405B
BW
VE-375
2" - 4"
BW/PLAIN
VE-374
1/2" - 3/4"
PLAIN
1/2" - 4"
(Note 4)
1/2" - 3/4"
ASTM A 105
3000
(Note 11)
Tag
1/2" - 3/4"
T-05A
Long Nip.
E10
1/2" - 1 1/2"
1" - 1 1/2"
600
Description
1/2" - 3/4"
SW
(1,6mm)
Size
BW
12" - 24"
Standard
Ball
2" - 10"
Sch 80
T-02B
Class
Valves
Material
1" - 1 1/2"
Pipe
(Note 12)
Corrosion
Allowance
ASTM A 105
1" - 1 1/2"
2" - 4"
6" - 24"
Gate
VE-402
VE-403
VE-406
VE-407
VE-408
(Note 5)
VG-45
2" - 6"
VG-10
8" - 24"
VG-11
2" - 4"
VGL-07
6" - 8"
VGL-07E
Globe
Flange
(Note 7)
FLG-42
1/2" - 1 1/2"
SW (RTJ)
FLG-13
2" - 24"
WN (RTJ)
FLG-15
1/2" - 24"
JA-01
Gasket
(Notes 2 and 10)
1/2" - 24"
Nut
BLIND (RTJ)
Oval
1/2" - 1 1/2"
VR-56
2" - 24"
VR-38
JI-04
Stud
600
Check
ASTM A 105
(Notes 2)
1/2" - 1 7/8"
ASTM A 193 Gr B7
(Notes 2 and
4)
1/2" - 1 7/8"
(Notes 2)
1/2" - 1 7/8"
ASTM A 194 Gr 2H
(Notes 2 and
4)
1/2" - 1 7/8"
ASTM A 194 Gr 7
Other
1/2" - 1 1/2"
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
78 of 134
Service
CODE
ASME B31.3
SHEET:
BG-Inert Gas; CI-Chemical Injection (Non-Corrosive); W-Industrial Water (Fresh, NonCorrosive / De-Aerated Sea Water); IW-Fresh And De-Aerated Sea Water Injection
0C / 210C
(Note 8); G-Glycol; FG-Combustible Gas (Note 9); P-Process (Non corrosive
(Note 12)
hydrocarbon); AM-Amine (Nota 13).
Corrosion
Allowance
Class
Standard
(1,6mm)
600
E10
up to 38
1480
50
1450
100
1346
110
1340
150
1280
210
1200
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud bolts and ASTM
A194 GR 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-01 and TAM-15) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 Use only in onshore installations.
9 Use only upstream filters.
10 Isolating joint see drawing on the appendix 15.
11 When requerid Fully Tight Valve (VET), see types in appendix 14.
12 In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of standard ASME
B31.3.
13 For use Amine Inlet from the Amine Contactors.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 110C
(Note 9)
(1,6mm)
600
E10R
CODE
ASME B31.3
79 of 134
Tag
Size
(in)
Wall or
Class
Valves
Ends
Material
Ball
Size
T-05A
Pipe
(Note 9)
1/2" - 1 1/2"
Sch 80
2" - 8"
Sch 40
(Note 4)
Description
Tag
PLAIN
API 5L Gr B PSL 1
seamless
T-02A
10"
VE-04B
VE-20
2" - 4"
6" - 24"
1/2" - 1 1/2"
VG-45
2" - 6"
VG-10
8" - 24"
VG-11
BW
VE-13
Sch 60
T-02B
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
12" - 24"
(Notes 1 and 6)
3000
Red.
LRE-01
Cap
TAM-05
SW
VE-25
ASTM A 105
1/2" - 1 1/2"
Union
UN-04
Coupling
L-04
Short Nip.
T-05A
Long Nip.
PLAIN
Red.Nip.C
NIPR.C-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Gate
1/2" - 4"
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
(Note 5)
BW/PLAIN
Wall
thickness
according to
pipe
Red. Tee
TRE-01
Conc. Red.
REDC-01
Globe
Ecc. Red.
REDE-01
2" - 4"
VGL-07
Cap
TAM-02
6" - 8"
VGL-07E
1/2" - 1 1/2"
VR-56
2" - 24"
VR-38
1/2" - 1 1/2"
2" - 24"
Cross
CRUZ-02
Weldolet
WOL-01
BW
ASTM A 105
Check
Flange
(Note 7)
FLG-42
1/2" - 1 1/2"
FLG-13
2" - 24"
FLG-15
1/2" - 24"
1/2" - 24"
(Notes 2 and 8)
(Notes 2)
1/2" - 1 7/8"
Other
ASTM A 105
BLIND (RTJ)
600
Oval
JI-04
Nut
WN (RTJ)
JA-01
Gasket
Stud
SW (RTJ)
600
1/2" - 1 7/8"
ASTM A 193 Gr B7
ASTM A 193 Gr B16
ASTM A 194 Gr 2H
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
80 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 110C
(Note 9)
(1,6mm)
600
E10R
up to 38
1480
110
1343
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud bolts
and ASTM A194 GR 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 Isolating joint see drawing on the appendix 15.
9 In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table
323.2.2 A of standard ASME B31.3.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
PCW-Produced water
0C / 90C
_______
600
E11
Tag
Size
(in)
Wall or Class
Ends
Material
Ball
Size
T-05A
PLAIN
1" - 1 1/2"
API 5L Gr B PSL 1
seamless
Pipe
T-02A
2" - 10"
1" - 1 1/2"
Sch 80
2" - 4"
BW
T-02B
Red. Tee
TRE-03
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
12" - 24"
6" - 24"
Description
Tag
VE-202
VE-198
VE-199
VE-200
6000
1" - 1 1/2"
(Notes 1 and 5)
3000
Red.
LRE-01
Cap
TAM-05
Union
UN-04
Coupling
L-04
Short Nip.
1" - 1 1/2"
Red.Nip.C
PLAIN
NIPRE-10
Red.Nip.C
NIPRC-04A
1" - 4"
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
VG-86
2" - 6"
VG-83
8" - 24"
VG-84
CRL-02
Tee
TE-02
Red. Tee
TRE-01
2" - 4"
VGL-46
6" - 8"
VGL-46E
BW/PLAIN
Wall
thickness
according to
pipe
CRL-01
L.R.ELL 45
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
Globe
2" - 24"
Conc. Red.
BW
Check
ASTM A 105
1" - 1 1/2"
2" - 24"
FLGFlange
(Note 9)
FLG-13
600
Gasket
(Note 2)
Nut
ASTM A 105
1" - 1 1/2"
BLIND (RTJ)
1" - 24"
600
JP-
1" - 10"
1/16 (1,6mm)
JP-
12" - 24"
1/8 (3.2mm)
1" - 24"
600
JI-04
Stud
WN (RTJ)
(Notes 2 and
4)
1/2" - 1 1/4"
Oval
Plain
PTFE Expanded
Oval
VR-118
VR-116
Other
(RF) WN
1" - 24"
FLG-15
JA-01
(Note 4)
1" - 1 1/2"
NIPRC-04
Red .Nip.E
L.R.ELL 90
Gate
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
Fenolic resin
ASTM A 193 Gr B7
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-31
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
PCW-Produced water
0C / 90C
_______
600
E11
Up to 38
1480
50
1453
90
1372
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use nipple THD X Plain and threaded cap (TAM-01 and TAM-15) after blocking drains and vents.
6 Isolating joint see drawing on the appendix 15.
7 Use pipes, fittings and flanges of 2"and 3" with Sch 40 onshore.
8 All pipes shall be organic coated according appendix 18.
9 For on shore facilities only.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
83 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 70C
_____
600
E14
Tag
T-05A
Valves
Size
(in)
Wall or
Class
1" - 1 1/2"
Ends
Material
Ball
PLAIN
Size
Description
Tag
1" - 1 1/2"
VE-46
2" - 4"
Pipe
(Note 7)
T-02A
(Notes 1, 4 and 7)
Fittings
Elbow 90
JO-07
Elbow 45
JO-08
Equal Tee
TE-05
Red. Tee
TRE-02
Cross
CRUZ-05
Half Coupling
ML-02
Red.
LRE-01
Cap
TAM-05
Union
UN-04
Coupling
L-04
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
Nut
1" - 1 1/2"
3000
SW
6" - 24"
2" - 6"
VG-10
8" - 24"
VG-11
2" - 4"
VGL-07
6" - 10"
VGL-07E
VE-25
ASTM 105
API 5L Gr B PSL 1
seamless
PLAIN
1" - 4"
BW/PLAIN
Wall
thickness
according to
pipe
Check
2" - 24"
BW
2" - 24"
VR-94
VR-66
ASTM A 105
1" - 1 1/2"
WN (RTJ)
FLG-13
2" - 24"
WN (RTJ)
FLG-15
1" - 24"
1" - 24"
600
Oval
Other
ASTM A 105
BLIND (RTJ)
1" - 1 1/2"
Carbon steel coated Zn-Ni max.
hardness 90 Brinell
ASTM A 193 Gr B7
(Note 6)
VE-20
Globe
FLG-13
Gasket
JA-01
(Notes 6 and 8)
VE-13
Gate (Note 3)
1" - 1 1/2"
Red.Nip.C
Stud
12" - 24"
T-05A
Long Nip.
Flange
(Note 5)
Sch 80
BW
T-02B
Short Nip.
2" - 10"
1/2" - 1 7/8"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-08
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
84 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 70C
_____
600
E14
up to 38
1480
50
1453
70
1412
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use only in offshore installations.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
4 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
6 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
7 Piping, conections and fittings should be revested with polyethylene according appendix 13.
8 Isolating joint see drawing on the appendix 15.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 130C
(Note 11)
_______
600
E16
Tag
T-36
Pipe
T-37A
(Notes 1 and 3)
T-37B
Elbow 90
JO-45
Elbow 45
JO-46
Equal Tee
TE-38
Red. Tee
TRE-33
Cross
CRUZ-32
Size
(in)
Wall or Class
1/2"
3/4"
1"
1 1/2"
2"
3"
4"
6"
8"
10"
12"
14"
16"
3000
Cap
PLAIN
UN-23
Coupling
L-27
NIPRE-18
Red .Nip.E
NIPRE-18A
S.R.ELL 90
CRC-22
L.R.ELL 90
CRL-30
L.R.ELL 45
CRL-31
Tee
TE-39
Red. Tee
TRE-34
Conc. Red.
REDC-15
Ecc. Red.
REDE-14
Cap
TAM-36
Cross
CRUZ-33
Weldolet
WOL-07
1/2" - 1 1/2"
VE-221
2" - 4"
VE-222
6" - 16"
VE-223
1/2" - 1 1/2"
VE-224
2" - 4"
VE-225
6" - 16"
VE-226
1/2" - 1 1/2"
VE-233
2" - 4"
VE-234
6" - 16"
VE-235
1/2" - 1 1/2"
VE-293
2" - 4"
VE-294
6" - 16"
VE-295
1/2" - 1 1/2"
VG-88
2" - 6"
VG-95
8" - 16"
VG-96
2" - 4"
VGL-85
6" - 8"
VGL-86
1/2" - 1 1/2"
VR-119
2" - 16"
VR-124
SW
ASTM A 182 Gr F 51
(UNS S31803)
1/2" - 4"
2" - 16"
BW
ASTM A 182 Gr F 51
(UNS S31803)
1/2" - 1 1/2"
1/2" - 16"
FLG-128
2" - 16"
SW (RTJ)
600
BLIND (RTJ)
1/2 - 12"
1/2" - 16"
1/2" - 1 1/2"
(Notes 12 and
1/2" - 1 1/2"
13)
(Notes 12)
1/2" - 1 1/2"
(Notes 12 and
1/2" - 1 1/2"
13)
ASTM A 182 Gr F 51
(UNS S31803)
WN (RTJ)
Octogonal
600
(Notes 12)
(Note 2)
Globe
FLG-127
JA-10
Gate
BW/PLAIN
Wall
thickness
according to
pipe
FLG-126
JI-04
Nut
Tag
NIPRC-11
NIPRC-11A
Stud
Description
PLAIN
Red.Nip.C
Gasket
(Note 6)
Ball
Size
BW
T-36
Red .Nip.E
Flange
(Note 4)
1/2" - 1 1/2"
Long Nip.
Red.Nip.C
Material
TAM-35
Union
Short Nip.
Ends
(Note 7)
Oval
Check
Other
ASTM A 193 Gr B7
ASTM A 193 Gr B16
ASTM A 194 Gr 2H
1/2" - 1 1/2"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-35
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 130C
(Note 11)
_______
600
E16
up to 38
1499
50
1499
100
1469
110
1441
130
1387
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves shall be used.
3 Use niple THD X PLAIN and threaded cap (TAM-37) after drains and vents blocking.
4 Flanges 1 1/2" may be used, if strictly necessary.
5 Use according appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According appendix 16 - Welding qualification requirements for superduplex and duplex steel.
8 According appendix 17 - Casting qualification requirements minimum for valves superduplex and duplex steel.
9 When requerid Fully Tight Valve (VET), see types in appendix 14.
10 For use gas inlet from Amine contactors and outlet gas K.0. drum for K.0. drum of compression unit.
11 In possibility of occurrence of low temperatures up to -46C, this spec can be used in accordance with table of ASME B31.3 standard.
12 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
13 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
TECHNICAL SPECIFICATION
N:
REV:
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C/90C
(Notes 10)
(6,4mm)
600
E17
Tag
T-05A
Size
(in)
1" - 1 1/2"
2"
T-02A
Pipe
(Notes 10)
Wall or
Class
XXS
Ends
Valves (Note 9)
Material
Ball
Description
Tag
1" - 1 1/2"
VE-333D
2" - 4"
6" - 24"
VE-376
1" - 1 1/2"
VE-337D
2" - 4"
6" - 24"
PLAIN
XXS
3" - 4"
Sch 160
6" - 8"
Sch 120
10" - 12
0,812"
14"
0,875"
(Note 4)
Size
API 5L Gr B PSL 1
seamless
VE-374
VE-375
BW
T-02B
Elbow 90
JO-37
Elbow 45
JO-38
Equal Tee
TE-34
Red. Tee
TRE-29
Cross
CRUZ-28
Half Coupling
ML-14
16"
1,000"
18"
1,062
20"
0.938"
22"
1.062"
24"
1.125"
1" - 1 1/2"
Red.
LRE-12
Cap
TAM-31
Union
UN-19
Coupling
L-23
9000
API 5L Gr B PSL 1
Welded (E = 0,95)
SW
VE-378
VE-379
VE-380
ASTM A 105
Short Nip.
T-05A
Long Nip.
Red.Nip.C
1" - 1 1/2"
PLAIN
1" - 4"
BW/PLAIN
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Wall thickness
according to
pipe
2 - 24"
Cap
TAM-02
Cross
CRUZ-02
Weldolet
Gate
BW
1" - 1 1/2"
VG-45
2" - 6"
VG-10
8" - 24"
VG-11
ASTM A 105
WOL-01
(Note 5)
Globe
2" - 4"
VGL-07
6" - 8"
VGL-07E
1" - 1 1/2"
VR-56
2" - 24"
VR-38
1" - 1 1/2"
Check
Flange
(Note 7)
FLG-42
1" - 1 1/2"
SW (RTJ)
FLG-13
2" - 24"
WN (RTJ)
FLG-15
1" - 24"
Other
ASTM A 105
BLIND (RTJ)
600
JA-01
Gasket
(Notes 2 and 8)
1" - 24"
Nut
JI-04
Stud
Oval
(Notes 2)
1/2" - 1 7/8"
ASTM A 193 Gr B7
(Notes 2 and
4)
1/2" - 1 7/8"
(Notes 2)
1/2" - 1 7/8"
ASTM A 194 Gr 2H
(Notes 2 and
4)
1/2" - 1 7/8"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 90C
(Notes 10)
(6,4 mm)
600
E17
up to 38
1480
50
1453
100
1351
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and
ASTM A 194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-01 and TAM-15) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 Isolating joint see drawing on the appendix 15.
9 When requerid Fully Tight valve (VET), see types in appendix 14.
10 In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of standard ASME
B31.3.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
1 of 2
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 190C
___
600
E30
Pipes and Fittings (Coated with Inconel 625 - According appendix 21) (Note 9)
Item
Tag
T-05A
T-02A
Pipe
T-02B
(Notes 1 and 6)
Equal Tee
TRE-35
Cross
CRUZ-34
Half Coupling
ML-19
Red. Coupling
LRE-17
Cap
TAM-39
Union
UN-24
Coupling
L-28
1"
SCH 80 XS 0,179"
1 1/2"
SCH 80 XS 0,200"
2"
3"
4"
6"
8"
SCH 80 XS 0,500"
10"
SCH 80 0,594"
12"
SCH 80 0,688"
14"
SCH 80 0,750"
16"
SCH 80 0,844"
Ends
API 5L Gr B PSL 1
seamless
BW
API 5L Gr B PSL 1
seamless
(Note 4)
Size
Description
Tag
1" - 1 1/2"
VE-459
6' - 16"
VE-460
VE-461
VE-462
API 5L Gr B PSL 1
welded (E=0,95)
1" - 1 1/2"
ASTM A 105
API 5L Gr B PSL 1
seamless
1" - 1 1/2"
Red. Nip. C
NIPRC-04
Red. Nip. E
NIPRE-10
Red. Nip. C
NIPRC-04A
Red. Nip. E
NIPRE-10A
1" - 4"
Wall
thickness
according to
pipe
BW
ASTM A 234 Gr WPB
C903D-01 (90)
Gate
API 5L Gr B PSL 1
seamless
C453D-01 (45)
Tee
Ball
2" - 4"
T-05A
Long Nip.
3D. R. ELBOW
Wall or Class
Valves
Material
TE-41
Red. Tee
Short Nip.
Size
(in)
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
2" - 16"
ASTM A 234 Gr WPB
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01A
ASTM A 105
Butterfly
Globe
FLG-151
Flange
JA-12
Gasket
(Note 7)
1" - 16"
600
FLG-152
BLIND (RTJ)
2" - 10"
1 - 1 1/2"
VR-137
2" - 24"
VR-138
1" - 1 1/2"
ASTM A 105
Check
WN (RTJ)
1" - 16"
Octagonal
Inconel 625
Oval
Fenolic resin
600
JI-04
1" - 16"
VGL-95
Other
Stud
Nut
(Notes 2)
1/2" - 1 1/2"
ASTM A 193 Gr B7
(Notes 2 and 4)
1/2" - 1 1/2"
(Notes 2)
1/2" - 1 1/2"
ASTM A 194 Gr 2H
(Notes 2 and 4)
1/2" - 1 1/2"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-40
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
2 of 2
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 190C
___
600
E30
up to 38
1480
100
1351
150
1308
190
1278
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and ASTM
A 194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
5 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
6 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
7 Isolating joint see drawing on the appendix 15.
8 When requerid Fully Tight Valve (VET), see types in appendix 14.
9 All piping shall be internal Inconel 625 coated according Appendix 21.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
85 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
ASME B31.3
-100C /
200C
_______
Tag
Size
(in)
Wall or Class
1/2" - 1 "
SCH 40S
T-11
Valves
Ends
Material
PLAIN
1 1/2"
SCH 80S
4" - 10"
SCH 120
T-30
BW
12" - 18"
Elbow 90
JO-23
Elbow 45
JO-24
Equal Tee
TE-15
Red. Tee
TRE-10
Cross
CRUZ-15
Half Coupling
ML-09
(Notes 1 and 4)
LRE-05
TAM-19
Union
UN-12
Coupling
L-13
F3
Ball
Tag
1/2" - 1"
VE-237
1 1/2"
VE-237B
2"
VE-409
SCH 100
3000
Cap
900
(Note 7)
Description
3" - 4"
Red.
Standard
Size
2" - 3"
Pipe
Class
SW
1/2" - 1 1/2"
Short Nip.
T-11
Long Nip.
6" - 18"
VE-410
VE-411
1/2" - 1"
VE-270
1 1/2"
VE-270B
2"
VE-272
3" - 4"
VE-273
6" - 18"
VE-274
PLAIN
Red.Nip.C
NIPRC-07
Red .Nip.E
NIPRE-13
Red.Nip.C
NIPRC-07A
Red .Nip.E
NIPRE-13A
BW/PLAIN
1/2" - 4"
S.R.ELL 90
CRC-04
L.R.ELL 90
CRL-07
L.R.ELL 45
CRL-08
Tee
TE-21
Red. Tee
TRE-16
Conc. Red.
REDC-04
Wall
thickness
according to
pipe
2" - 18"
Ecc. Red.
REDE-04
Cap
TAM-25
Cross
CRUZ-19
Weldolet
WOL-04
1/2" - 1"
ASTM A 403 Gr WP 316L
1 1/2"
2"
BW
3" - 4"
6" - 18"
ASTM A 182 Gr F 316L
1/2" - 1"
1 1/2"
2"
3" - 4"
6" - 18"
Gate
VE-275
VE-275B
VE-277
VE-278
VE-279
VE-280
VE-280B
VE-282
VE-283
VE-284
(Note 3)
1/2" - 1 1/2"
VG-53
2"
VG-28
3" - 6"
VG-26
8" - 18"
VG-27
2"
VGL-15
3" - 4"
VGL-14
6" - 10"
VGL-14E
1/2" - 1 1/2"
Globe
Flange
(Note 5)
FLG-62
1/2" - 1 1/2"
FLG-60
2"
FLG-61
1/2" - 2"
SW (RTJ)
1500
BLIND (RTJ)
FLG-59
900
FLG-58
WN (RTJ)
JA-06
1/2" - 2"
1500
Gasket
JA-05
3" - 18"
900
(Note 10)
JI-05
1/2" - 2"
1500
JI-04
3" - 18"
900
Nut
Check
BLIND (RTJ)
3" - 18"
Stud
WN (RTJ)
2"
Fenolic resin
3" - 10"
Octagonal
(Notes 8)
3/4" - 1 7/8"
3/4" - 1 7/8"
(Notes 8)
3/4" - 1 7/8"
(Notes 8 and 9)
3/4" - 1 7/8"
ASTM A 194 Gr 7
VR-84
VR-47
VR-46
Other
ASTM A 320 Gr L7
(Notes 8 and 9)
1/2" - 1 1/2"
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-26
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
86 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-100C /
200C
_______
900
F3
up to 38
1799
50
1741
100
1514
150
1366
200
1269
Temp. (C)
Branch Connections
(Note 2)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 For onshore facilities only, stub in connections may be used according to ASME B31.3.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
4 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
6 Use according appendix 5.
7 When requerid Fully Tight valve (VET), see types in appendix 14.
8 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
9 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A
194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
10 Isolating joint see drawing on the appendix 15.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
87 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 350 C
(1,6mm)
900
F4
Tag
T-05A
Size
(in)
Wall or
Class
1/2" - 3/4"
Sch 160
1" - 1 1/2"
Pipe
T-02A
Valves
Ends
PLAIN
Sch 80
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Half Coupling
ML-03
TAM-06
Union
UN-05
Coupling
L-05
Short Nip.
1/2" - 1 1/2"
VG-46
2"
VG-65
3" - 4"
VG-63
6" - 18"
VG-64
2"
VGL-36
3" - 4"
VGL-35
6" - 8"
VGL-35E
1/2" - 1 1/2"
6000
SW
Gate (Note 4)
ASTM A 105
1/2" - 1 1/2"
API 5L Gr B PSL 1
seamless
T-05A
PLAIN
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
Tag
BW
12" - 18"
Long Nip.
Red.Nip.C
Description
Sch 120
Elbow 90
Ball
Size
2" - 3"
4" - 10"
T-02B
Material
1/2" - 4"'
BW/PLAIN
Wall
thickness
according to
pipe
2" - 18"
Globe
ASTM A 234 Gr WPB
BW
ASTM A 105
Check
2"
3" - 18"
2"
3" - 18"
Flange
(Note 6)
FLG-43
1/2" - 1 1/2"
FLG-18
2"
FLG-19
1/2" - 2"
FLG-16
3" - 18"
Stud
Nut
VR-103
VR-102
VR-101
WN (RTJ)
BLIND (RTJ)
900
1/2" - 1 1/2"
BLIND (RTJ)
1/2" - 2"
1500
Octagonal
3" - 18"
900
Oval
Other
ASTM A 105
WN (RTJ)
(Note 2)
VR-100
SW (RTJ)
1500
FLG-17
JA-02
Gasket
(Notes 2 and 10) JA-01
VR-03
3/4" - 1 7/8"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
88 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 350 C
(1,6mm)
900
F4
Temp. (C)
up to 38
2221
250
1795
50
2181
300
1640
100
2027
350
1590
150
1960
200
1905
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
6 Flanges 1 1/2" may be used, if strictly necessary.
7 Use only downstream centrifuge.
8 Use only downstream filters.
9 Use according appendix 5.
10 Isolating joint see drawing on the appendix 15.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
89 of 134
TITLE:
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 90C
(3,2mm)
900
F5
CODE
ASME B31.3
Tag
T-05A
Pipe
T-02A
Half coupling
Short Nip.
Size
(in)
Wall or
Class
3/4"
XXS
2"
Sch 160
3"
XXS
4" - 6"
Sch 120
ML-03
Valves
Ends
Material
PLAIN
API 5L Gr B PSL 1 seamless
Ball
Size
Tag
3/4"
VE-49D
BW
6000
SW
ASTM A 105
XXS
PLAIN
Wall thickness
according to
pipe
BW
(Note 4)
Description
3/4"
T-05A
Long Nip.
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
2" - 6"
ASTM A 105
Gate
2 1/16" - 4
1/16"
Globe
Check
2"
3" - 6"
Flange
(Note 4)
FLG-18
2"
FLG-19
2"
FLG-16
1500
Stud
Nut
WN (RTJ)
BLIND (RTJ)
900
JA-02
2"
1500
Octagonal
JA-01
3" - 6"
900
Oval
(Note 2)
ASTM A 105
WN (RTJ)
3" - 6"
FLG-17
Gasket
(Note 2)
BLIND (RTJ)
7/8" - 1 1/8"
Other
ASTM A 193 Gr B7
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VR-40
VR-39
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
90 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 90C
(3,2mm)
900
F5
up to 38
2221
50
2181
90
2058
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 The flange FLG-16 or FLG-18 will be used as a counter flange of VG ABRAS-04 (FJA).
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
91 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-46C / 110C
(1,6mm)
900
F6
Tag
Size
(in)
Wall or
Class
1/2" - 3/4"
Sch 160
T-09
Ends
Valves (Note 8)
Material
Ball
Size
Description
Tag
1/2" - 3/4"
VE-94C
1" - 1 1/2"
VE-94B
2"
VE-95
3" - 4"
VE-96
6" - 10"
VE-97
PLAIN
1" - 1 1/2"
Sch 80
2" - 3"
Pipe
T-07A
Elbow 90
JO-17
Elbow 45
JO-18
Equal Tee
TE-12
Red. Tee
TRE-08
Cross
CRUZ-12
Half Coupling
ML-07
Red. Coupling
LRE-04
Cap
TAM-12
4"
Sch 120
6"
0.500"
8"
0.625"
10"
0.812"
(Notes 1 and 5)
6000
ASTM A 333 Gr 6
seamless
BW
SW
1/2" - 1 1/2"
Union
UN-09
Coupling
L-09
Short Nip.
ASTM A 333 Gr 6
seamless
T-09
Long Nip.
PLAIN
Red.Nip.C
NIPRC-05
Red .Nip.E
NIPRE-16
Red.Nip.C
NIPRC-05A
Red .Nip.E
NIPRE-16A
Gate
BW/PLAIN
1/2" - 4"
S.R.ELL 90
CRC-02
L.R.ELL 90
CRL-03
L.R.ELL 45
CRL-04
Tee
TE-08
Red. Tee
TRE-04
Conc. Red.
REDC-02
Ecc. Red.
REDE-02
Cap
TAM-08
Wall
thickness
according to
pipe
2" - 10"
Cross
CRUZ-08
Weldolet
WOL-02
BW
Globe
2"
VGL-28
3" - 4"
VGL-29
6" - 10"
VGL-29E
1/2" - 1 1/2"
VR-58
2"
VR-59
3" - 10"
VR-60
Check
2"
3" - 10"
Flange
(Note 7)
FLG-48
1/2" - 1 1/2"
FLG-34
2"
FLG-35
1/2" - 2"
FLG-32
3" - 10"
VR-82
(Note 4)
VR-81
(Note 4)
SW (RTJ)
1500
WN (RTJ)
BLIND (RTJ)
WN (RTJ)
900
Gasket
(Note 2)
Stud
Nut
FLG-33
3" - 10"
JA-04
1/2" - 2"
JA-03
3" - 10"
Other
BLIND (RTJ)
1500
900
Octagonal
Oval
1/2" - 1 1/2"
ASTM A 320 Gr L7
(Note 2)
3/4" - 1 3/8"
ASTM A 194 Gr 4/S3
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-21
N:
TECHNICAL SPECIFICATION
REV:
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
92 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-46C / 110C
(1,6mm)
900
F6
-46 to 38
2221
50
2181
100
2027
110
2014
Branch Connections
Temp. (C)
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46C / -15C).
7 Flanges 1 1/2" may be used, if strictly necessary.
8 When requerid Fully Tignt valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
93 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-46C / 110C
(1,6mm)
900
F6R
Pipe
Tag
T-09
(Notes 1 and 5)
Fittings and Accessories
Wall or
Class
1/2" - 3/4"
Sch 160
1" - 1 1/2"
T-07A
Elbow 90
JO-17
Elbow 45
JO-18
Equal Tee
TE-12
Red. Tee
TRE-08
Cross
CRUZ-12
Half Coupling
ML-07
Red. Coupling
LRE-04
Cap
TAM-12
Union
UN-09
Coupling
L-09
Short Nip.
Size
(in)
Ends
Material
PLAIN
ASTM A 333 Gr 6
seamless
Sch 80
2" - 10"
Valves (Note 8)
Ball
Size
Description
Tag
1/2" - 3/4"
VE-94C
1" - 1 1/2"
VE-94B
2"
VE-95
3" - 4"
VE-96
6" - 10"
VE-97
BW
6000
SW
1/2" - 1 1/2"
ASTM A 333 Gr 6
seamless
T-09
Long Nip.
PLAIN
Red.Nip.C
NIPRC-05
Red.Nip.E
NIPRE-16
Red.Nip.C
NIPRC-05A
Red.Nip.E
NIPRE-16A
S.R.ELL 90
CRC-02
L.R.ELL 90
CRL-03
L.R.ELL 45
CRL-04
Tee
TE-08
Gate
1/2" - 4"
BW/PLAIN
Wall
thickness
according to
pipe
Red. Tee
TRE-04
Conc. Red.
REDC-02
Globe
Ecc. Red.
REDE-02
2"
VGL-28
Cap
TAM-08
3" - 4"
VGL-29
6" - 10"
VGL-29E
1/2" - 1 1/2"
VR-58
2"
VR-59
3" - 10"
VR-60
Cross
CRUZ-08
Weldolet
WOL-02
2" - 10"
BW
Check
2"
3" - 10"
Flange
(Note 7)
FLG-48
1/2" - 1 1/2"
FLG-34
2"
FLG-35
1/2" - 2"
FLG-32
3" - 10"
Nut
BLIND (RTJ)
900
1/2" - 2"
1500
Octagonal
JA-03
3" - 10"
900
Oval
Other
WN (RTJ)
JA-04
1/2" - 1 1/2"
(Note 2)
VR-81
(Note 4)
WN (RTJ)
BLIND (RTJ)
Stud
VR-82
(Note 4)
SW (RTJ)
1500
FLG-33
Gasket
(Note 2)
3/4" - 1 3/8"
ASTM A 194 Gr 4/S3
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-21
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
94 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-46C / 110C
(1,6mm)
900
F6R
-46 / 38
2221
110
2014
Temp. (C)
Branch Connections
(Note 3)
Notas:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46C / -15C).
7 Flanges 1 1/2" may be used, if strictly necessary.
8 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
TECHNICAL SPECIFICATION
N:
REV:
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
95 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 210C
(Note 11)
(1,6mm)
900
F10
Tag
Size
(in)
Wall or
Class
1/2" - 3/4"
Sch 160
Valves
Ends
Ball
API 5L Gr B PSL 1
seamless
1" - 1 1/2"
Sch 80
Size
Description
Tag
VE-415C
1" - 1 1/2"
VE-415B
2"
VE-416
2" - 3"
T-02A
4" - 10"
BW
Sch 120
T-02B
Elbow 90
12" - 18"
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
3" - 4"
(Notes 1 and 6)
6" - 18"
Cross
CRUZ-06
Coupling
L-05
Half Coupling
ML-03
6000
SW
ASTM A 105
VE-417
VE-418
VE-419
1/2" - 3/4"
VE-420C
1" - 1 1/2"
VE-420B
2"
VE-421
3" - 4"
6" - 18"
1/2" - 1 1/2"
Red. Coupling LRE-02
Cap
TAM-06
Union
UN-05
Short Nip.
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
(Note 10)
(Note 4)
1/2" - 3/4"
PLAIN
T-05A
Pipe
(Note 11)
Material
PLAIN
Red.Nip.C
NIPRC-04
Red.Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red.Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
1/2" - 4"'
BW/PLAIN
1/2" - 3/4"
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Wall
thickness
according to
pipe
1" - 1 1/2"
ASTM A 234 Gr WPB
2"
BW
2" - 18"
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
3" - 4"
6" - 18"
Cross
CRUZ-02
Weldolet
WOL-01
ASTM A 105
1/2" - 3/4"
1" - 1 1/2"
2"
3" - 4"
6" - 18"
Gate
VE-422
VE-423
VE-424
VE-425C
VE-425B
VE-426
VE-427
VE-428
VE-429
VE-430C
VE-430B
VE-431
VE-432
VE-433
VE-434
(Note 5)
1/2" - 1 1/2"
VG-46
2"
VG-14
3" - 6"
VG-12
8" - 18"
VG-13
2"
VGL-09
3" - 4"
VGL-08
6" - 10"
VGL-08E
1/2" - 1 1/2"
VR-03
2"
VR-40
3" - 18"
VR-39
Globe
Flange
(Note 7)
FLG-43
1/2" - 1 1/2"
FLG-18
2"
FLG-19
1/2" - 2"
SW (RTJ)
1500
WN (RTJ)
BLIND (RTJ)
FLG-16
ASTM A 105
Check
WN (RTJ)
3" - 18"
900
FLG-17
BLIND (RTJ)
JA-02
1/2" - 2"
1500
JA-01
Gasket
(Notes 2 and 9) JI-05
3" - 18"
900
1/2" - 2"
1500
Octagonal
Oval
Fenolic resin
JI-04
Stud
Nut
3" - 18"
900
(Notes 2)
3/4" - 1 7/8"
ASTM A 193 Gr B7
(Notes 2 and
4)
3/4" - 1 7/8"
Other
(Notes 2)
3/4" - 1 7/8"
ASTM A 194 Gr 2H
(Notes
2 and 4)
3/4" - 1 7/8"
ASTM A 194 Gr 7
1/2" - 1 1/2"
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
96 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
BG-Inert Gas; CI-Chemical Injection (Non-Corrosive); FG-Combustible Gas; WIndustrial Water (Fresh, Non-corrosive / De-Aerated Sea Water); IW-Fresh And
De-Aerated Sea Water Injection (Note 8); G-Glycol; P-Process (Non-corrosive
Hidrocarbon); HWU-Heating Water-Utilities
0C / 210C
(Note 11)
(1,6mm)
900
F10
Temp. (C)
up to 38
2221
210
1886
50
2181
100
2027
150
1960
200
1905
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud bolts
and ASTM A194 GR 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 Use only in onshore installations.
9 Isolating joint see drawing on the appendix 15.
10 When requerid Fully Tight valve (VET), see types in appendix 14.
11 In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of standard
ASME B31.3.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
97 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 110C
(Note 10)
(1,6mm)
900
F10R
Tag
T-05A
(Note
Pipe
10)
1/2" - 3/4"
Sch 160
1" - 1 1/2"
T-02A
2" - 10"
T-02B
12" - 18"
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Valves (Note 9)
Ends
PLAIN
Sch 80
Sch 100
6000
SW
Material
API 5L Gr B PSL 1
seamless
API 5L Gr B PSL 1
welded (E=0,85)
ASTM A 105
Ball
1/2" - 1 1/2"
Description
Tag
1/2" - 3/4"
VE-05C
1" - 1 1/2"
VE-05B
2"
VE-15
3" - 4"
6" - 18"
VE-26
1/2" - 3/4"
VE-102C
1" - 1 1/2"
VE-102B
2"
VE-108
3" - 4"
6" - 18"
1/2" - 1 1/2"
VG-46
2"
VG-14
3" - 6"
VG-12
8" - 18"
VG-13
2"
VGL-09
3" - 4"
VGL-08
6" - 10"
VGL-08E
1/2" - 1 1/2"
VR-03
2"
VR-40
3" - 18"
VR-39
1/2" - 1 1/2"
TAM-06
Union
UN-05
Short Nip.
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
(Note 4)
Size
L-05
(Notes 1 and 6)
Wall or
Class
BW
Coupling
Fittings
Size
(in)
VE-14
VE-21
PLAIN
Red.Nip.C
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
1/2" - 4"
BW/PLAIN
Wall
thickness
according to
pipe
2" - 18"
Gate
VE-107
VE-119
VE-125
(Note 5)
BW
ASTM A 105
Globe
Check
FLG-43
Flange
(Note 7)
1/2" - 1 1/2"
FLG-18
2"
FLG-19
1/2" - 2"
FLG-16
3" - 18"
SW (RTJ)
1500
900
FLG-17
JA-02
1/2" - 2"
1500
3" - 18"
900
1/2" - 2"
1500
JI-04
3" - 18"
900
Nut
ASTM A 105
WN (RTJ)
BLIND (RTJ)
JA-01
Gasket
(Notes 2 and 8) JI-05
Stud
WN (RTJ)
BLIND (RTJ)
Octagonal
Other
Oval
Fenolic resin
(Notes 2 and 4)
3/4" - 1 7/8"
ASTM A 193 Gr B7
(Notes 2 )
3/4" - 1 7/8"
(Notes 2 and 4)
3/4" - 1 7/8"
ASTM A 194 Gr 2H
(Notes 2)
3/4" - 1 7/8"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-17
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
98 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 110C
(Note 10)
(1,6mm)
900
F10R
up to 38
2221
110
2014
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud bolts and
ASTM A194 GR 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 Isolating joint see drawing on the appendix 15.
9 When
10 requerid
In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of standard
ASME B31.3.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
0
SHEET:
E&P
TITLE:
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
PCW-Produced water
0C / 90C
______
900
F11
Tag
Size
(in)
Wall or
Class
Ends
Ball
Description
Size
T-05A
1" - 1 1/2"
PLAIN
Sch 80
Pipe
T-02A
API 5L Gr B PSL 1
seamless
2" - 3"
2"
4" - 10"
BW
Sch 120
(Notes 1 and 5)
T-02B
Elbow 90
JO-09
Elbow 45
JO-10
Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Coupling
L-05
API 5L Gr B PSL 1
welded (E=0,85)
12" - 18"
6000
SW
Tag
VE-186D
VE-187
VE-189
3" - 4"
6" - 18"
1" - 1 1/2"
VG-73
2"
VG-74
3" - 6"
VG-78
8" - 18"
VG-79
2"
VGL-42
3" - 4"
VGL-44
6" - 10"
VGL-44E
VE-190
VE-191
ASTM A 105
1" - 1 1/2"
TAM-06
Union
UN-05
Short Nip.
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
1" - 1 1/2"
Red.Nip.C
PLAIN
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
1" - 4"
BW/PLAIN
Wall thickness
according to
pipe
2" - 18"
BW
Gate
ASTM A 105
(Note 4)
Globe
FLG-18
1" - 2"
WN (RTJ)
1500
Flange
(Note 7)
FLG-19
FLG-16
1" - 2"
3" - 18"
BLIND (RTJ)
900
FLG-17
Gasket
(Note 2)
Stud
Nut
Check
ASTM A 105
WN (RTJ)
1" - 1 1/2"
BLIND (RTJ)
JA-02
1" - 2"
1500
JA-01
3" - 18"
900
JI-05
1" - 2"
1500
JI-04
3" - 18"
900
Octagonal
2"
Fenolic resin
3" - 18"
1" - 1 1/2"
Oval
3/4" - 1 7/8"
ASTM A 194 Gr 2H
VR-109
VR-110
VR-114
Other
ASTM A 193 Gr B7
(Note 2)
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-31
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
0
SHEET:
E&P
TITLE:
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
PCW-Produced water
0C / 90C
______
900
F11
at 38
2221
50
2181
90
2058
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
6 Isolating joint see drawing on the appendix 15.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
TECHNICAL SPECIFICATION
N:
REV:
DR-ENGP-1.1
CLIENT:
B
SHEET:
E&P
TITLE:
101 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 70C
______
900
F14
Tag
T-05A
Pipe
(Note 7)
T-02A
Size
(in)
1" - 1 1/2"
Wall or
Class
Sch 80
Ends
4" - 10"
API 5L Gr B PSL 1
seamless
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Ball
Size
Description
Tag
1" - 1 1/2"
VE-47
2"
VE-15
3" - 4"
6" - 18"
2"
VG-14
3" - 6"
VG-12
8" - 18"
VG-13
2"
VGL-09
3" - 4"
VGL-08
6" - 10"
VGL-08E
1" - 1 1/2"
VR-95
2"
VR-68
3" - 18"
VR-67
1" - 1 1/2"
BW
Sch 120
T-02B
Material
PLAIN
2" - 3"
Valves
API 5L Gr B PSL 1
welded (E=0,85)
12" - 18"
6000
SW
VE-14
VE-21
VE-26
ASTM A 105
Cap
Union
UN-05
Coupling
L-05
Short Nip.
1" - 1 1/2"
TAM-06
PLAIN
Red.Nip.C
NIPRC-04
Red.Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red.Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
Gate (Note 3)
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
BW/PLAIN
1" - 4"'
Wall
thickness
according to
pipe
Globe
BW
2" - 18"
ASTM A 105
Check
Flange
(Note 5)
FLG-18
1" - 1 1/2"
FLG-18
2"
FLG-19
1" - 2"
FLG-16
WN (RTJ)
1500
BLIND (RTJ)
Stud
Nut
ASTM A 105
WN (RTJ)
3" - 18"
900
1" - 2"
1500
Octagonal
3" - 18"
900
Oval
FLG-17
JA-02
Gasket
(Notes 6 and 8) JA-01
Other
WN (RTJ)
BLIND (RTJ)
Carbon steel coated Zn-Ni max.
hardness 90 Brinell
ASTM A 193 Gr B7
(Note 6)
3/4" - 1 7/8"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-08
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
B
SHEET:
E&P
TITLE:
102 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 70C
______
900
F14
up to 38
2221
50
2181
70
2119
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use only in offshore installations.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
4 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
6 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
7 Piping, conections and fittings should be revested with polyethylene according appendix 13.
8 Isolating joint see drawing on the appendix 15.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
103 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-100C / 210C
________
1500
G3
Valves (Note 7)
Tag
T-33
Size
(in)
Wall or
Class
1/2" - 3/4"
Sch 80S
1" - 1 1/2"
Ends
PLAIN
Material
ASTM A 312 Gr TP 316L
seamless
Sch 160
Ball
Size
Description
Tag
1/2" - 3/4"
VE-238C
1" - 1 1/2"
VE-238B
2" - 3"
VE-435
4" - 12"
VE-436
1/2" - 3/4"
VE-285C
1" - 1 1/2"
VE-285B
2" - 3"
VE-287
4" - 12"
VE-288
1/2" - 1 1/2"
VG-53
2" - 4"
VG-28
6" - 10"
VG-29
2" - 3"
4" - 6"
(Notes 1 and 5)
Pipe
T-34
(Note 8)
Elbow 90
JO-25
Elbow 45
JO-26
Equal Tee
TE-16
Red. Tee
TRE-11
Cross
CRUZ-16
Half Coupling
ML-10
Red. Coupling
LRE-06
Cap
TAM-20
Union
UN-13
Coupling
L-14
Short Nip.
8"
XXS
1.000"
10"
1.250"
12"
Sch 160
6000
SW
1/2" - 1 1/2"
T-33
Long Nip.
Red.Nip.C
BW
PLAIN
NIPRC-07
Red .Nip.E
NIPRE-13
Red.Nip.C
NIPRC-07A
Red .Nip.E
NIPRE-13A
S.R.ELL 90
CRC-04
L.R.ELL 90
CRL-07
L.R.ELL 45
CRL-08
Tee
TE-21
Red. Tee
TRE-16
Conc. Red.
REDC-04
Gate
1/2" - 4"
BW/PLAIN
Wall
thickness
according to
pipe
2" - 12"
(Note 4)
BW
Ecc. Red.
REDE-04
Globe
Cap
TAM-25
2" - 3"
VGL-15
Cross
CRUZ-19
Weldolet
WOL-04
4" - 10"
VGL-15E
1/2" - 1 1/2"
VR-84
2" - 12"
VR-47
1/2" - 1 1/2"
Check
Other
Flange
(Note 6)
FLG-62
1/2" - 1 1/2"
FLG-61
1/2" - 12"
FLG-60
2" - 12"
SW (RTJ)
1500
BLIND (RTJ)
WN (RTJ)
JA-06
1/2" - 12"
1500
Octagonal
JI-05
1/2" - 12"
1500
Oval
Fenolic resin
Gasket
(Note 10)
Stud
Nut
(Notes 2)
3/4" - 1 7/8"
ASTM A 320 Gr L7
(Notes 2 and 9)
3/4" - 1 7/8"
(Notes 2)
3/4" - 1 7/8"
(Notes 2 and 9)
3/4" - 1 7/8"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-27
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
104 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-100C / 210C
________
1500
G3
from -100 up to 38
2999
93
2575
149
2281
210
2089
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use niple THD X PLAIN and threaded cap (TAM-38) after drains and vents blocking.
6 Flanges 1 1/2" may be used, if strictly necessary.
7 When requerid Fully Tight Valves (VET), see types in appendix 14.
8 From -101C to -30C material shall be solution heat treated.
9 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
10 Isolating joint see drawing on the appendix 15.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
A
SHEET:
E&P
TITLE:
105 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 350 C
(1,6mm)
1500
G4
Tag
T-05A
(Notes 1 and 4)
Pipe
T-02A
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Half Coupling
ML-03
TAM-06
Union
UN-05
Coupling
L-05
Short Nip.
Size
(in)
Valves
Wall or
Class
Ends
1/2" - 1 1/2"
XXS
PLAIN
2" - 4"
Sch 160
6"
0,750"
8"
1.000"
10"
1.125"
6000
Material
NIPRE-10
Red.Nip.C
NIPRC-04A
Red.Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
1/2" - 1 1/2"
VG-46
2" - 4"
VG-65
6" - 10"
VG-66
2" - 3"
VGL-36
4" - 8"
VGL-36E
1/2" - 1 1/2"
Tag
SW
ASTM A 105
Gate
Red.Nip.E
Description
1/2" - 1 1/2"
Long Nip.
NIPRC-04
Size
BW
T-05A
Red.Nip.C
Ball
1/2" - 4"
BW/PLAIN
Wall
thickness
according to
pipe
2" - 10"
Globe
ASTM A 234 Gr WPB
BW
Check
ASTM A 105
2" - 10"
2" - 10"
VR-03
VR-100
VR-102
Other
Flange
(Note 5)
Gasket
(Note 2)
Stud
Nut
FLG-43
1/2" - 1 1/2"
FLG-18
2" - 10"
FLG-19
1/2" - 10"
JA-02
1/2" - 10"
SW (RTJ)
1500
WN (RTJ)
1/2"- 1 1/2"
ASTM A 105
BLIND (RTJ)
1500
Octagonal
(Note 2)
3/4" - 1 7/8"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-18
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
A
SHEET:
E&P
TITLE:
106 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0 / 350 C
(1,6mm)
1500
G4
Temp. (C)
up to 38
3702
250
3041
50
3634
300
2887
100
3379
350
2723
150
3269
200
3176
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
107 of 134
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 90C
(1,6mm)
1500
G5
Tag
T-05A
Pipe
T-02A
Wall or
Class
Ends
3/4"
XXS
PLAIN
2"
Sch 160
3"
XXS
4"
Sch 160
6"
Half Coupling
Short Nip.
Valves
Size
(in)
ML-03
Material
Ball
Size
Description
Tag
3/4"
VE-49D
2 1/16" - 4 1/16"
XXS
6000
SW
ASTM A 105
XXS
PLAIN
Wall thickness
according to
pipe
BW
3/4"
T-05A
Long Nip.
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
2" - 6"
Gate (Note 4)
ASTM A 105
VG ABRAS-06
Globe
Check
2" - 6"
Flange
(Note 4)
FLG-18
Gasket
JA-02
(Notes 2 and 4)
Stud
Nut
2" - 6"
1500
FLG-19
WN (RTJ)
ASTM A 105
Other
BLIND (RTJ)
2" - 6"
1500
Octagonal
(Note 2)
7/8" - 1 3/8"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VR-40
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
108 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 90C
(1,6mm)
1500
G5
up to 38
3702
50
3634
90
3430
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 The flange FLG-18 will be used as a counter flange of VG ABRAS-04 (FJA).
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
(Note 6)
ASME B31.3
109 of 134
Temp.
Range
Corrosion
Allowance
Class
Standard
-46C / 110C
(1,6mm)
1500
G6
Tag
T-09
Pipe
T-07A
Elbow 90
JO-17
Elbow 45
JO-18
Equal Tee
TE-12
Red. Tee
TRE-08
Cross
CRUZ-12
Half Coupling
ML-07
Red. Coupling
LRE-04
Cap
TAM-12
Union
UN-09
Coupling
L-09
Short Nip.
Size
(in)
Valves
Wall or
Class
Ends
1/2" - 1 1/2"
XXS
PLAIN
2"
Sch 160
3"
XXS
4"
Sch 160
6"
XXS
8"
1.000"
10"
1.250"
BW
SW
Material
ASTM A 333 Gr 6
seamless
(Note 8)
Ball
Size
Description
Tag
1/2" - 1 1/2"
VE-94D
2" - 3"
VE-95
4" - 10"
VE-99
6000
1/2" - 1 1/2"
Gate
ASTM A 333 Gr 6
seamless
T-09
Long Nip.
PLAIN
Red.Nip.C
NIPRC-05
Red.Nip.E
NIPRE-16
Red.Nip.C
NIPRC-05A
Red.Nip.E
NIPRE-16A
S.R.ELL 90
CRC-02
L.R.ELL 90
CRL-03
L.R.ELL 45
CRL-04
Tee
TE-08
Red. Tee
TRE-04
Conc. Red.
REDC-02
Ecc. Red.
REDE-02
Cap
TAM-08
Cross
CRUZ-08
Weldolet
WOL-02
1/2" - 4"
BW/PLAIN
Wall
thickness
according to
pipe
2" - 10"
BW
Globe
2" - 3"
VGL-28
4" - 8"
VGL-28E
Check
1/2" - 1 1/2"
2" - 10"
2" - 10"
VR-58
VR-59
VR-82
(Note 4)
Other
1/2" - 1 1/2"
FLG-48
Flange
(Note 7)
Gasket
(Note 2)
Stud
Nut
1/2" - 1 1/2"
FLG-34
2" - 10"
FLG-35
1/2" - 10"
JA-04
1/2" - 10"
SW (RTJ)
1500
WN (RTJ)
BLIND (RTJ)
1500
Octagonal
(Note 2)
3/4" - 1 7/8"
ASTM A 194 Gr 4/S3
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-23
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
110 of 134
CODE
Service (Note 6)
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-46C / 110C
(1,6mm)
1500
G6
-46/38
3702
50
3634
100
3379
110
3357
Temp. (C)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46C/-15C).
7 Flanges 1 1/2" may be used, if strictly necessary.
8 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Tag
T-09
Wall or
Class
Ends
1/2" - 1 1/2"
XXS
PLAIN
BW
(Notes 1 and 5)
4" - 10"
Elbow 90
JO-17
Elbow 45
JO-18
Equal Tee
TE-12
Red. Tee
TRE-08
Cross
CRUZ-12
Half Coupling
ML-07
Red. Coupling
LRE-04
Cap
TAM-12
Union
UN-09
Coupling
L-09
Short Nip.
Sch 160
T-07A
Corrosion
Allowance
Class
Standard
-46C / 110C
(1,6mm)
1500
G6R
Valves (Note 8)
Material
ASTM A 333 Gr 6
seamless
Sch 120
6000
Temp.
Range
(Note 5)
Size
(in)
2" - 3"
Pipe
(Note 6)
ASME B31.3
111 of 134
SW
Ball
Size
Description
Tag
1/2" - 1 1/2"
VE-94D
2" - 3"
VE-95
4" - 10"
VE-99
1/2" - 1 1/2"
ASTM A 333 Gr 6
seamless
T-09
Long Nip.
PLAIN
Red.Nip.C
NIPRC-05
Red.Nip.E
NIPRE-16
Red.Nip.C
NIPRC-05A
Red.Nip.E
NIPRE-16A
S.R.ELL 90
CRC-02
L.R.ELL 90
CRL-03
L.R.ELL 45
CRL-04
Tee
TE-08
Gate
1/2" - 4"
BW/PLAIN
Wall
thickness
according to
pipe
Red. Tee
TRE-04
Conc. Red.
REDC-02
Globe
Ecc. Red.
REDE-02
2" - 3"
VGL-28
Cap
TAM-08
4" - 8"
VGL-28E
1/2" - 1 1/2"
Cross
CRUZ-08
Weldolet
WOL-02
2" - 10"
BW
Check
2" - 10"
2" - 10"
VR-58
VR-59
VR-82
(Note 4)
Other
1/2" - 1 1/2"
FLG-48
Flange
(Note 7)
Gasket
(Note 2)
Stud
Nut
1/2" - 1 1/2"
FLG-34
2" - 10"
FLG-35
1/2" - 10"
JA-04
1/2" - 10"
SW (RTJ)
1500
WN (RTJ)
BLIND (RTJ)
1500
Octagonal
(Note 2)
3/4" - 1 7/8"
ASTM A 194 Gr 4/S3
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-23
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
112 of 134
CODE
ASME B31.3
SHEET:
(Note 6)
Temp.
Range
Corrosion
Allowance
Class
Standard
-46C / 110C
(1,6mm)
1500
G6R
-46/38
3702
110
3357
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46C/-15C).
7 Flanges 1 1/2" may be used, if strictly necessary.
8 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
113 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 210C
(Note 9)
(1,6mm)
1500
G10
Tag
T-05A
Size
(in)
Wall or
Class
Ends
1/2" - 1 1/2"
XXS
PLAIN
2"
Sch 160
3"
XXS
4"
Sch 160
6"
XXS
8"
1.000"
Material
(Note 4)
Description
Tag
1/2" - 1 1/2"
VE-437D
2" - 3"
VE-421
4" - 24"
VE-438
1/2" - 1 1/2"
VE-439D
2" - 3"
VE-431
4" - 24"
VE-394
1/2" - 1 1/2"
VG-46
2" - 4"
VG-14
6" - 24"
VG-15
2" - 3"
VGL-09
4" - 8"
VGL-09E
1/2" - 1 1/2"
VR-03
2" - 24"
VR-40
1/2" - 1 1/2"
T-02A
Pipe
(Note 9)
Ball
Size
BW
10"
1.250"
12"
API 5L X60 PSL 1 welded (E=0,95)
Note 8
T-29
14" - 24"
Elbow 90
Sch 140
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Coupling
L-05
Half Coupling
ML-03
6000
SW
ASTM A 105
1/2" - 1 1/2
TAM-06
Union
UN-05
Short Nip.
T-05A
Gate
Long Nip.
PLAIN
Red. Nip. C
Red. Nip. E
NIPRC-04
NIPRE-10
Red. Nip. C
NIPRC-04A
Red. Nip. E
NIPRE-10A
1/2" - 4"
S. R. ELL 90
CRC-01
L. R. ELL 90
CRL-01
L. R. ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
BW/PLAIN
Globe
2" - 10"
Cap
TAM-02
Cross
CRUZ-02
Weldolet
CRC-20
L. R. ELL 90
CRL-09
L. R. ELL 45
CRL-10
Tee
BW
TRE-17
Conc. Red.
REDC-05
Ecc. Red.
REDE-05
Cap
TAM-28
Cross
CRUZ-25
Check
12" - 24"
FLG-43
1/2" - 1 1/2"
SW (RTJ)
FLG-18
2" - 10"
WN (RTJ)
FLG-19
1/2" - 10"
1500
FLG-72
BLIND (RTJ)
ASTM A 694 Gr F60 (Note 8)
12" - 24"
BLIND (RTJ)
JA-02
Octagonal
1/2" - 24"
JI-05
Stud
Nut
Other
ASTM A 105
WN (RTJ)
FLG-73
Gasket
(Notes 2 and 11)
ASTM A 105
TE-23
Red. Tee
Flange
(Note 7)
Wall
thickness
according to
pipe
WOL-01
S. R. ELL 90
(Note 5)
1500
Oval
(Notes 2)
7/8" - 1 7/8"
ASTM A 193 Gr B7
(Notes
2 and 4)
7/8" - 1 7/8"
(Notes 2)
7/8" - 1 7/8"
ASTM A 194 Gr 2H
(Notes
2 and 4)
7/8" - 1 7/8"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-18
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
114 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 210C
(Note 9)
(1,6mm)
1500
G10
up to 38
3702
50
3634
100
3379
150
3269
200
3176
210
3149
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud bolts and ASTM
A194 GR 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 Maximum carbon equivalent 0,42%.
9 In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of
standard ASME B31.3.
10 Use only in onshore installations.
11 Isolating joint see drawing on the appendix 15.
12 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
117 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 110C
(Note 9)
(1,6mm)
1500
G10P
Tag
Size
(in)
Wall or
Class
1/2"
0,188"
3/4"
0,219"
T-05A
PLAIN
1"
0,179"
1 1/2"
0,281"
4" - PIGGABLE
SCH 80 XS 0,337"
6" - PIGGABLE
SCH 80 XS 0,432"
8" - PIGGABLE
0,594"
10" - PIGGABLE
12" - PIGGABLE
0,812"
14" - PIGGABLE
0,875"
16" - PIGGABLE
1,000"
T-38B
18" - PIGGABLE
1,125"
20" - PIGGABLE
1,250"
22" - PIGGABLE
24" - PIGGABLE
Elbow 90
JO-09
1,500"
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Half Coupling
ML-03
6000
Material
API 5L Gr B PSL 1
seamless
T-38A
Pipe
(Note 9)
(Notes 1 and 4)
Valves (Note 7)
Ends
Ball
(Note 3)
Size
Description
Tag
1/2" - 1 1/2"
VE-102D
4"
VE-108P
6" - 24"
VE-126P
BW
SW
ASTM A 105
PLAIN
API 5L Gr B PSL 1
seamless
1/2" - 1 1/2
Red. Coupling
LRE-02
Cap
TAM-06
Union
UN-05
Coupling
L-05
Short Nip.
T-05A
Long Nip.
3D. R. ELBOW
(PIGGABLE)
C903D-02 (90)
5D. R. ELBOW
(PIGGABLE)
C905D-02 (90)
Tee (PIG)
TE-23P
TRE-17P
Gate
C453D-02 (45)
4" - 24"
Wall
thickness
according to
pipe
C455D-02 (45)
ASTM A 694 Gr F65
(Note 8)
Globe
2" - 3"
VGL-09
4" - 8"
VGL-09E
Check
FLG-43
SW (RTJ)
1/2" - 1 1/2"
ASTM A 105
FLG-19
Flange
(Note 5)
BLIND (RTJ)
1500
FLG-72
WN (RTJ)
4" - 24"
FLG-73
Gasket
(Note 2)
BLIND (RTJ)
Octagonal
JA-02
1/2" - 24"
JI-05
Stud
1500
Oval
(Notes 2)
3/4" - 3 1/2"
ASTM A 193 Gr B7
(Notes 2 and 3)
3/4" - 3 1/2"
(Notes 2)
3/4" - 3 1/2"
ASTM A 194 Gr 2H
(Notes 2 and 3)
3/4" - 3 1/2"
ASTM A 194 Gr 7
Nut
Other
1/2" - 1 1/2"
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-18
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
118 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 110C
(Note 9)
(1,6mm)
1500
G10P
from 10 up to 38
3702
70
3532
110
3357
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
4 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
6 Isolating joint see drawing on the appendix 15.
7 When requerid Fully Tight valve (VET), see types in appendix 14.
8 Maximum carbon equivalent 0,42%.
9 In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of standard ASME
B31.3.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
115 of 134
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 110C
(Note 10)
(1,6mm)
1500
G10R
Tag
T-05A
(Notes 1 and 6)
Pipe
(Note 10)
1/2" - 1 1/2"
Wall or
Class
XXS
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Material
PLAIN
2" - 3"
Sch 160
4" - 10"
Sch 120
6000
ML-03
SW
TAM-06
Union
UN-05
(Note 4)
Description
Tag
1/2" - 1 1/2"
VE-43D
2" - 3"
VE-15
4" - 10"
VE-27
1/2" - 1 1/2"
VE-102D
2" - 3"
VE-108
4" - 10"
VE-126
ASTM A 105
1/2" - 1 1/2"
Ball
Size
BW
L-05
Half Coupling
Short Nip.
T-05A
Long Nip.
PLAIN
Red.Nip.C
Valves (Note 9)
Ends
Elbow 90
Coupling
Size
(in)
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Gate
1/2" - 4"
BW/PLAIN
Wall
thickness
according to
pipe
2" - 10"
(Note 5)
1/2" - 1 1/2"
VG-46
2" - 4"
VG-14
6" - 10"
VG-15
BW
Ecc. Red.
REDE-01
Globe
Cap
TAM-02
2" - 3"
VGL-09
Cross
CRUZ-02
Weldolet
WOL-01
4" - 8"
VGL-09E
1/2" - 1 1/2"
VR-03
2" - 10"
VR-40
1/2" - 1 1/2"
ASTM A105
Check
Flange
(Note 7)
FLG-43
1/2" - 1 1/2"
FLG-18
2" - 10"
FLG-19
1/2" - 10"
JA-02
Gasket
(Notes 2 and 8)
SW (RTJ)
1500
WN (RTJ)
Octagonal
1/2" - 10"
JI-05
1500
Oval
(Notes 2)
3/4" - 1 1/4"
ASTM A 193 Gr B7
(Notes 2 and 4)
3/4" - 1 1/4"
(Notes 2)
3/4" - 1 1/4"
ASTM A 194 Gr 2H
(Notes 2 and 4)
3/4" - 1 1/4"
ASTM A 194 Gr 7
Stud
Other
ASTM A 105
BLIND (RTJ)
Nut
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-18
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
ASME B31.3
116 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp.
Corrosion
Service
Class
Standard
Range
Allowance
0C / 110C
(Note 10)
(1,6mm)
1500
G10R
over 38
3702
110
3357
Temp. (C)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud
bolts and ASTM A194 GR 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 Isolating joint see drawing on the appendix 15.
9 When requerid Fully Tight valve (VET), see types in appendix 14.
10 In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of standard
ASME B31.3.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
D
SHEET:
E&P
TITLE:
119 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
PCW-Produced water
0C / 90C
___
1500
G11
Tag
T-05A
Pipe
T-02A
Size
(in)
Wall or
Class
Ends
1" - 1 1/2"
XXS
PLAIN
2"
Sch 160
3"
XXS
4"
Sch 160
5"
T-29
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Coupling
L-05
Material
API 5L Gr B PSL 1
seamless
Ball
(Note 4)
Size
Description
Tag
1" - 1 1/2"
VE-186D
2" - 3"
VE-187
4" - 24"
VE-188
1" - 1 1/2"
VG-73
2" - 4"
VG-74
6" - 24"
VG-75
2" - 3"
VGL-42
4" - 8"
VGL-42E
1" - 1 1/2"
VR-109
2" - 24"
VR-110
1" - 1 1/2"
XXS
BW
6"
8"
1.000"
10"
1.250"
12"
Sch 40
14" - 24"
Sch 140
6000
SW
ASTM A 105
1" - 1 1/2
TAM-06
Union
UN-05
Short Nip.
Gate
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
(Note 5)
PLAIN
Red. Nip. C
NIPRC-04
Red. Nip. E
NIPRE-10
Red. Nip. C
NIPRC-04A
Red. Nip. E
NIPRE-10A
1" - 4"
BW/PLAIN
S. R. ELL 90 CRC-01
L. R. ELL 90
CRL-01
L. R. ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
2" - 10"
Globe
Wall
thickness
according to
pipe
BW
ASTM A 105
S. R. ELL 90 CRC-20
L. R. ELL 90
CRL-09
L. R. ELL 45
CRL-10
Tee
TE-23
Red. Tee
TRE-17
Conc. Red.
REDC-05
Ecc. Red.
REDE-05
Cap
TAM-28
Cross
CRUZ-25
Flange
(Note 7)
Check
ASTM A 694 Gr F 60
(Note 8)
12" - 24"
FLG-18
2" - 10"
WN (RTJ)
FLG-19
1" - 10"
BLIND (RTJ)
FLG-72
1500
WN (RTJ)
12" - 24"
FLG-73
Gasket
(Notes 2 and 9)
BLIND (RTJ)
Octagonal
JA-02
1" - 24"
JI-05
Stud
Nut
1500
Oval
Other
ASTM A 105
ASTM A 694 Gr F 60
(Note 8)
(Notes 2)
7/8" - 1 7/8"
ASTM A 193 Gr B7
(Notes
2 and 4)
7/8" - 1 7/8"
(Notes 2)
7/8" - 1 7/8"
ASTM A 194 Gr 2H
(Notes
2 and 4)
7/8" - 1 7/8"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-32
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
D
SHEET:
E&P
TITLE:
120 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
Class
Standard
ASME B31.3
PCW-Produced water
0C / 90C
___
1500
G11
up to 38
3702
50
3634
90
3430
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A
4
194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 Maximum carbon equivalent 0,42%.
9 Isolating joint see drawing on the appendix 15.
10 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENTE:
SHEET:
E&P
TTULO:
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 90C
(Note 10)
____
1500
G12
CODE
ASME B31.3
121 of 134
Tag
T-17
Size
(in)
1/2" - 1 1/2"
Wall or
class
Sch 40S
Ends
Pipe
(Notes 1 and 3)
T-20
Elbow 90
JO-35
Elbow 45
JO-36
Equal Tee
TE-33
Red. Tee
TRE-27
Cross
CRUZ-26
Half Coupling
ML-13
0.281"
6" - 8"
Sch 80S
10"
0.719"
12"
0.875"
14"
0.938"
16"
1.062"
18"
1.250"
20"
1.375"
22"
1.500"
24"
Sch 120
6000
Description
Tag
1/2" - 1 1/2"
VE-168
2" - 4"
VE-169
6" - 24"
VE-170
1/2" - 1 1/2"
VE-171
2" - 4"
VE-172
6" - 24"
VE-173
1/2" - 1 1/2"
VG-67
2" - 12"
VG-68
14" - 24"
VG-69
2" - 10"
1/2" - 1 1/2"
VR-104
2" - 24"
VR-105
1/2" - 1 1/2"
BW
ASTM A 790 (UNS S32760)
welded (E=1)
SW
ASTM A 182 Gr F 55
(UNS S32760)
1/2" - 1 1/2"
UN-18
Coupling
L-22
ASTM A 790 (UNS S32760)
seamless
T-17
Long Nip.
Ball
Size
TAM-29
Union
Short Nip.
4"
Material
PLAIN
2" - 3"
T-19
Gate
PLAIN
Red.Nip.C
NIPRC-09
Red.Nip.E
NIPRE-15
Red.Nip.C
NIPRC-09A
Red.Nip.E
NIPRE-15A
S.R.ELL 90
CRC-06
L.R.ELL 90
CRL-13
L.R.ELL 45
CRL-14
Tee
TE-25
Red. Tee
TRE-19
Conc. Red.
REDC-07
Ecc. Red.
REDE-07
Cap
TAM-27
Cross
CRUZ-21
Weldolet
WOL-05
1/2" - 4"
BW/PLAIN
Wall
thickness
according to
pipe
(Note 2)
ASTM A 815
(UNS S32760)
Globe
2" - 24"
BW
VGL-40
ASTM A 182 Gr F 55
(UNS S32760)
Check
Other
Flange
(Note 4)
Gasket
(Note 6)
FLG-109
1/2" - 1 1/2"
FLG-110
1/2" - 24"
FLG-111
2" - 24"
Octagonal
1/2" - 24"
(Notes 11)
Nut
1500
Oval
1/2" - 1 7/8"
(Notes 11 and
1/2" - 1 7/8"
12)
(Notes 11)
BLIND (RTJ)
1/2" - 1 7/8"
(Notes 11 and
1/2" - 1 7/8"
12)
ASTM A 182 Gr F 55
(UNS S32760)
WN (RTJ)
JA-06
JI-05
Stud
SW (RTJ)
1500
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-30
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENTE:
E&P
TTULO:
122 of 134
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 90C
(Note 10)
____
1500
G12
CODE
ASME B31.3
SHEET:
at 38
3750
50
3750
90
3689
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
3 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
4 Flanges 1 1/2" may be used, if strictly necessary.
5 This Spec should only be used when recommended in appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According Appendix 16 welding qualification requirements for superduplex.
8 When requerid Fully Tight valve (VET), see types in appendix 14.
9 According appendix 17 - casting qualification requirements minimum for valves superduplex.
10 In possibility of occurrence of low temperatures up to -46C, this spec can be used in accordance with table A-1 of ASME B31.3
standard.
11 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
12 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM
A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENTE:
SHEET:
E&P
123 of 134
TTULO:
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 90C
(Note 10)
____
1500
G12P
CODE
ASME B31.4/ASME B31.8
Tag
T-17
Pipe
T-19
Size
(in)
Wall or
class
1/2"
0,147"
3/4"
0,154"
1"
0,179"
1 1/2"
0,200"
4" - PIGGABLE
0,237"
6" - PIGGABLE
0,280"
8" - PIGGABLE
0,322"
10" - PIGGABLE
T-19B
(Notes 1 and 2)
Fittings and Accessories
JO-35
Elbow 45
JO-36
Equal Tee
TE-33
Red. Tee
TRE-27
Cross
CRUZ-26
Half Coupling
ML-13
PLAIN
ASTM A 790 (UNS S32760)
seamless
Ball
Size
Description
Tag
1/2" - 1 1/2"
VE-171
4" - 14"
VE-173P
BW
0,500"
12" - PIGGABLE
14" - PIGGABLE
Elbow 90
Ends
0,562"
6000
SW
ASTM A 182 Gr F 55
(UNS S32760)
1/2" - 1 1/2"
Red. Coupling LRE-11
Cap
TAM-29
Union
UN-18
Coupling
L-22
Short Nip.
T-17
PLAIN
Gate
Long Nip.
3D. R. Elbow
(Piggable)
C903D-03 (90)
5D. R. Elbow
(Piggable)
C905D-03 (90)
Tee (PIG)
TE-25P
C453D-03 (45)
4" - 14"
Wall
thickness
according to
pipe
BW
C455D-03 (45)
ASTM A 815 (UNS S32760)
seamless
Globe
Check
Other
1/2" - 1 1/2"
FLG-109
Flange
(Note 3)
SW (RTJ)
1/2" - 1 1/2"
FLG-110
FLG-111
BLIND (RTJ)
4" - 14"
ASTM A 182 Gr F 55
(UNS S32760)
WN (RTJ)
1500
Gasket
(Note 5)
JA-07
Octagonal
1/2" - 14"
JI-05
Oval
Stud
(Notes 11 and
12)
Nut
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-30
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENTE:
E&P
TTULO:
124 of 134
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 90C
(Note 10)
____
1500
G12P
CODE
ASME B31.4/ASME B31.8
SHEET:
at 38
3750
50
3750
90
3689
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
3 Flanges 1 1/2" may be used, if strictly necessary.
4 This Spec should only be used when recommended in appendix 5.
5 Isolating joint see drawing on the appendix 15.
6 According Appendix 16 welding qualification requirements for superduplex.
7 When requerid Fully Tight valve (VET), see types in appendix 14.
8 According appendix 17 - casting qualification requirements minimum for valves superduplex.
9 Up to SDV shall be used carbon steel API 5L Gr X60 cladding with Inconel 625 (UNS N06625).
10 In possibility of occurrence of low temperatures up to -46C, this spec can be used in accordance with table A-1 of ASME B31.3 standard.
11 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
12 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A
194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
125 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 70C
_____
1500
G14
Tag
T-05A
Pipe
(Note 7)
T-02A
T-29
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Half Coupling
ML-03
Cap
Size
(in)
Wall or
Class
Ends
1" - 1 1/2"
XXS
PLAIN
2"
Sch 160
3"
XXS
4"
Sch 160
6"
XXS
8"
1.000"
10"
1.250"
12"
1.125"
14" - 18"
Sch 140
6000
Valves
Material
API 5L Gr B PSL 1
seamless
(Note 9)
Ball
Size
Description
Tag
1" - 1 1/2"
VE-47
2" - 3"
VE-15
4" - 18"
VE-27
2" - 4"
VG-14
6" - 18"
VG-15
2" - 3"
VGL-09
4" - 8"
VGL-09E
BW
SW
ASTM A 105
1" - 1 1/2"
TAM-06
Union
UN-05
Coupling
L-05
Short Nip.
Gate (Note 3)
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
Red.Nip.C
PLAIN
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
S.R.ELL 90
CRC-20
L.R.ELL 90
CRL-09
L.R.ELL 45
CRL-10
Tee
TE-23
Red. Tee
TRE-17
Conc. Red.
REDC-05
Ecc. Red.
REDE-05
Cap
TAM-28
Cross
CRUZ-25
Flange
(Note 5)
1" - 4"
BW/PLAIN
Globe
ASTM A234 Gr WPB
2" - 10"
Wall
thickness
according to
pipe
Check
BW
ASTM A 105
1" - 1 1/2"
2" - 18"
FLG-18
1" - 1 1/2"
WN (RTJ)
FLG-18
2" - 10"
WN (RTJ)
FLG-19
1" - 10"
BLIND (RTJ)
1500
FLG-72
ASTM A 105
BLIND (RTJ)
Other
1" - 1 1/2"
Stud
Nut
1" - 18"
1500
Octagonal
(Note 6)
VR-68
WN (RTJ)
FLG-73
JA-02
VR-95
12" - 18"
12" - 18"
Gasket
(Note 6)
7/8" - 1 7/8"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-09
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
126 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 70C
_____
1500
G14
up to 38
3705
50
3632
70
3575
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use only in offshore installations.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
4 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
6 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
7 Piping, conections and fittings should be revested with polyethylene according appendix 13.
8 Maximum carbon equivalent 0,42%.
9 When requerid Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 130C
(Note 10)
_______
1500
G16
Tag
T-36
T-37A
Pipe
T-37B
Size
(in)
Sch 40S
2" - 4"
Sch 80S
6"
0,500"
8"
Sch 100
10"
0,812"
12"
0,938"
14"
1,000"
16"
1,188"
18"
1,375"
20"
1,500"
22"
1,875"
(Notes 1 and 3)
24"
Elbow 90
JO-45
Elbow 45
JO-46
Equal Tee
TE-38
Red. Tee
TRE-33
Cross
CRUZ-32
Wall or Class
1/2" - 1 1/2"
Cap
Material
PLAIN
ASTM A 790 (UNS S31803)
seamless
Size
Tag
1/2" - 1 1/2"
VE-227
2" - 3"
VE-228
4" - 24"
VE-229
1/2" - 1 1/2"
VE-440
2" - 3"
VE-441
4" - 24"
VE-232
1/2" - 1 1/2"
VG-97
2" - 4"
VG-98
6" - 24"
VG-99
2" - 3"
VGL-87
4" - 8"
VGL-88
1/2" - 1 1/2"
VR-125
2" - 24"
VR-126
1/2" - 1 1/2"
BW
ASTM A 790 (UNS S31803)
welded (E=0,95)
2,062"
3000
Ball
Description
SW
ASTM A 182 Gr F 51
(UNS S31803)
1/2" - 1 1/2"
TAM-35
Union
UN-23
Coupling
L-27
Short Nip.
T-36
Long Nip.
Ends
(Note 7)
PLAIN
Red.Nip.C
NIPRC-11
Red .Nip.E
NIPRE-18
Red.Nip.C
NIPRC-11A
Red .Nip.E
NIPRE-18A
S.R.ELL 90
CRC-22
L.R.ELL 90
CRL-30
L.R.ELL 45
CRL-31
Tee
TE-39
Red. Tee
TRE-34
Conc. Red.
REDC-15
Ecc. Red.
REDE-14
Cap
TAM-36
Cross
CRUZ-33
Weldolet
WOL-07
1/2" - 4"
Gate
(Note 2)
BW/PLAIN
Wall
thickness
according to
pipe
2" - 24"
Globe
BW
ASTM A 182 Gr F 51
(UNS S31803)
Check
Other
Flange
(Note 4)
FLG-129
1/2" - 1 1/2"
FLG-130
1/2" - 24"
FLG-131
Gasket
(Note 6)
JA-11
(Notes 11)
2" - 24"
WN (RTJ)
1/2 - 24"
Octogonal
1/2" - 24"
1/2" - 1 7/8"
(Notes 11 and
1/2" - 1 7/8"
12)
(Notes 11)
Nut
BLIND (RTJ)
1500
JI-05
Stud
SW (RTJ)
1500
1/2" - 1 7/8"
(Notes 11 and
1/2" - 1 7/8"
12)
Oval
ASTM A 182 Gr F 51
(UNS S31803)
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-36
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 130C
(Note 10)
_______
1500
G16
up to 38
3750
50
3750
100
3674
110
3600
130
3460
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves shall be used.
3 Use niple THD X PLAIN and threaded cap (TAM-37) after drains and vents blocking.
4 Flanges 1 1/2" may be used, if strictly necessary.
5 Use according appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According appendix 16 - Welding qualification requirements for superduplex and duplex steel.
8 According appendix 17 - Casting qualification requirements minimum for valves superduplex and duplex steel.
9 When requerid Fully Tight valve (VET), see types in appendix 14.
10 In possibility of occurrence of low temperatures up to -46C, this spec can be used in accordance with table A-1 of ASME B31.3
standard.
11 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
12 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIESAND
MARINE SYSTEM
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 130C
(Note 10)
_______
1500
G16P
Tag
T-36
Pipe
T-37A
Size
(in)
Wall or Class
1/2"
0,147"
3/4"
0,154"
1"
0,179"
1 1/2"
0,200"
4"
0,237"
6"
8"
Ends
PLAIN
Material
Ball
Size
Description
Tag
1/2" - 1 1/2"
VE-440
4" - 24"
VE-232P
1/2" - 1 1/2"
VG-97
2" - 4"
VG-98
6" - 10"
VG-99
2" - 3"
VGL-87
4" - 8"
VGL-88
1/2" - 1 1/2"
VR-125
2" - 10"
VR-126
1/2" - 1 1/2"
0,432"
0,500"
(Note 7)
BW
10"
T-37B
Elbow 90
JO-45
Elbow 45
JO-46
Equal Tee
TE-38
Red. Tee
TRE-33
Cross
CRUZ-32
12"
0,562"
14"
0,688"
3000
SW
ASTM A 182 Gr F 51
(UNS S31803)
1/2" - 1 1/2"
TAM-35
Union
UN-23
Coupling
L-27
Short Nip.
T-36
PLAIN
Long Nip.
3D. R. Elbow
(Piggable)
C903D-04 (90)
5D. R. Elbow
(Piggable)
C905D-04 (90)
Tee (PIG)
TE-39P
C453D-04 (45)
4" - 14"
Wall
thickness
according to
pipe
Gate
(Note 2)
BW
C455D-04 (45)
ASTM A 815 (UNS S31803)
Globe
Check
Other
FLG-129
Flange
(Note 4)
FLG-131
Gasket
(Note 6)
Stud
Nut
JA-11
SW (RTJ)
1/2" - 1 1/2"
1500
FLG-130
4" - 14"
BLIND (RTJ)
WN (RTJ)
1/2 - 14"
Octogonal
1500
JI-05
(Notes 11 and
12)
(Notes 12)
(Notes 11 and
12)
(Notes 12)
1/2" - 14"
ASTM A 182 Gr F 51
(UNS S31803)
Oval
1/2" - 1 1/2"
ASTM A 193 Gr B7
1/2" - 1 1/2"
1/2" - 1 1/2"
ASTM A 194 Gr 2H
1/2" - 1 1/2"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-36
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 130C
(Note 10)
_______
1500
G16P
CODE
ASME B31.4/ASME B31.8
up to 38
3750
50
3750
100
3674
110
3600
130
3460
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves shall be used.
3 Use niple THD X PLAIN and threaded cap (TAM-37) after drains and vents blocking.
4 Flanges 1 1/2" may be used, if strictly necessary.
5 Use according appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According appendix 16 - Welding qualification requirements for superduplex and duplex steel.
8 According appendix 17 - Casting qualification requirements minimum for valves superduplex and duplex steel.
9 When requerid Fully Tight valve (VET), see types in appendix 14.
10 In possibility of occurrence of low temperatures up to -46C, this spec can be used in accordance with table A-1 of ASME B31.3 standard.
11 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
12 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
0
SHEET:
E&P
TITLE:
1 of 2
CODE
Service
Temp. Range
Corrosion
Allowance
ASME B31.8
0C / 100C
(1,6 mm)
Tag
T-05A
T-02A
Pipe
(Notes 8 and 9) T-33
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Coupling
L-05
Half Coupling
ML-03
1500
(Notes 8 and 9)
Class
Size
(in)
Wall or
Class
Ends
1 /2" - 1 1/2"
Sch 160
PLAIN
2"
0,281"
3" - 6"
Sch 160
8" - 10"
Sch 140
12"
0,625"
24"
1,000"
30"
1,250"
6000
G18
Valves (Note 7)
Material
API 5L Gr B PSL 1
seamless
BW
API 5L Gr X70 PSL 1
welded (E=1)
(Note 6)
SW
Standard
Ball
(Note 3)
Size
Description
Tag
1/2" - 1 1/2"
VE-43D
2" - 3"
VE-15
4" - 8"
VE-27
2" - 3"
VE-108
4" - 12"
VE-126
1/2" - 1 1/2"
VG-46
2" - 4"
VG-14
6" - 14"
VG-15
ASTM A 105
1/2" - 1 1/2"
TAM-06
Union
UN-05
Short Nip.
PLAIN
Red. Nip. C
NIPRC-04
Red. Nip. E
NIPRE-10
Red. Nip. C
NIPRC-04A
Red. Nip. E
NIPRE-10A
S. R. ELL 90
CRC-01
L. R. ELL 90
CRL-01
L. R. ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
S. R. ELL 90
CRC-20
L. R. ELL 90
CRL-09
L. R. ELL 45
CRL-10
Tee
TE-23
Red. Tee
TRE-17
Conc. Red.
REDC-05
Ecc. Red.
REDE-05
Cap
TAM-28
Cross
CRUZ-25
Flange
(Note 5)
Gasket
(Note 2)
Stud
Nut
1/2" - 4"
BW/PLAIN
Globe
ASTM A 234 Gr WPB
2" - 10"
2" - 3"
VGL-09
4" - 8"
VGL-09E
1/2" - 1 1/2"
VR-03
2" - 12"
VR-40
1/2" - 1 1/2"
Wall
thickness
according to
pipe
Check
BW
1/2" - 1 1/2"
FLG-18
2" - 10"
FLG-72
12" - 24"
SW (RTJ)
1500
WN (RTJ)
30"
JA-02
1/2" - 24"
JA-09
30"
ASTM A 105
12" - 30"
FLG-43
FLG-117
Gate
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
1500
Octogonal
ASTM A 105
ASTM A 694 Gr F70
(Note 6)
Other
(Notas 2)
7/8" - 2"
ASTM A 193 Gr B7
(Notas 2 e 3)
7/8" - 2"
(Notas 2)
7/8" - 2"
ASTM A 194 Gr 2H
(Notas 2 e 3)
7/8" - 2"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-18
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
0
SHEET:
E&P
TITLE:
2 de 2
CODE
Service
Temp. Range
Corrosion
Allowance
ASME B31.8
0C / 100C
(1,6 mm)
Class
1500
(Notes 8 and 9)
Standard
G18
Up to 38
3129
50
3030
100
2920
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM
A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
4 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
6 Maximum carbon equivalent 0,43%.
7 When requerid Fully Tight valve (VET), see types in appendix 14.
8 Pipes of NPD 30" and wall thickness of 1,250", max.pressure limited 3250 PSI.
9 In order to attempt specific project requirements, max.pressure of 3200 PSI for thickness to NPD 8", 10" and 24", based on
ASME B31.8 and indicated materials in spec each range, as below:
Thickness
NPD
Pressure
8"
Sch 140
10"
Sch 140
0,812
1,000
24"
1,000
3200 PSI
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
TITLE:
Service
CODE
ASME B31.3
(Note 6)
Temp.
Range
Corrosion
Allowance
Class
Standard
-46C / 70C
(3.2 mm)
1500
G19
Tag
T-09
Wall or
Class
Ends
1/2" - 1 1/2"
XXS
PLAIN
2" - 8"
Pipe
BW
10"
JO-
Elbow 45
JO-
Equal Tee
TE-
Red. Tee
TRECRUZ-
Half Coupling
ML-
Red. Coupling
LRE-
Cap
TAMUN-
Coupling
L-
Short Nip.
ASTM A 333 Gr 6
seamless
Size
Description
Tag
1/2" - 1 1/2"
VE-94D
2" - 3"
VE-95
4" - 10"
VE-99
1/2" - 1 1/2"
VE-412
SCH 160
SW
(Note 8)
Ball
2" - 3"
Cross
Union
Material
XXS
T-07A
Elbow 90
Valves
Size
(in)
4" - 10"
9000
VE-413
VE-414
1/2" - 1 1/2"
Gate
ASTM A 333 Gr 6
seamless
T-
Long Nip.
PLAIN
Red.Nip.C
NIPRC-05
Red.Nip.E
NIPRE-16
Red.Nip.C
NIPRC-05A
Red.Nip.E
NIPRE-16A
S.R.ELL 90
CRC-02
L.R.ELL 90
CRL-03
L.R.ELL 45
CRL-04
Tee
TE-08
Red. Tee
TRE-04
Conc. Red.
REDC-02
Ecc. Red.
REDE-02
Cap
TAM-08
Cross
CRUZ-08
Weldolet
WOL-02
1/2" - 4"
BW/PLAIN
Wall
thickness
according to
pipe
2" - 10"
BW
Globe
2" - 3"
VGL-28
4" - 8"
VGL-28E
Check
1/2" - 1 1/2"
2" - 10"
2" - 10"
VR-58
VR-59
VR-82
(Note 4)
Other
1/2" - 1 1/2"
FLG-48
Flange
(Note 7)
Gasket
(Note 2)
Stud
Nut
1/2" - 1 1/2"
FLG-34
2" - 10"
FLG-35
1/2" - 10"
JA-04
1/2" - 10"
SW (RTJ)
1500
WN (RTJ)
BLIND (RTJ)
1500
Octagonal
(Note 2)
3/4" - 1 7/8"
ASTM A 194 Gr 4/S3
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-23
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
CODE
Service (Note 6)
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
-46C / 70C
(3,2 mm)
1500
G19
-46/38
3705
50
3632
100
3363
Temp. (C)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46C/-15C).
7 Flanges 1 1/2" may be used, if strictly necessary.
8 When requerid Fully Tight Valve (VET), see types in appendix 14.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP.1-1
CLIENT:
SHEET:
E&P
CODE
Service
Temp.
Range
Corrosion
Allowance
ASME B31.3
-100C /
210C
_______
Tag
T- 41
(Notes 1 and 4)
Pipe
(Note 6)
T-30
(Note 8)
Equal Tee
TE-45
Red. Tee
TRE-39
Cross
CRUZ-38
Cap
TAM-42
Short Nip.
Wall or
Class
1"
0,358" XXS
1 1/2"
2"
3"
0,600" XXS
4"
0,674" XXS
6"
0,875"
8"
1,000"
10"
1,250"
Ends
NIPRC-07
Red. Nip. E
NIPRE-13
S. R. ELL 90
CRC-04
L. R. ELL 90
CRL-07
L. R. ELL 45
CRL-08
Tee
TE-21
Red. Tee
TRE-16
Conc. Red.
REDC-04
Ecc. Red.
REDE-04
Cap
TAM-25
Cross
CRUZ-19
Weldolet
WOL-04
2500
(Note 6)
Material
ASTM A 312 Gr TP 316L
seamless
Standard
H3
Ball
Size
Description
Tag
1"
VE-463D
1 1/2"
BW
2" - 3"
VE-464
4" - 10"
VE-465
1"
1 1/2"
ASTM A 182 Gr F 316L
VE-463C
2" - 3"
1" - 1 1/2"
4" - 10"
ASTM A 312 Gr TP 316L
seamless
T-41
Red. Nip. C
Class
Valves (Note 7)
(Note 6)
Size
(in)
Long Nip.
1 of 2
TITLE:
VE-466D
VE-466C
VE-467
VE-468
1" - 4"
Wall
thickness
according to
pipe
BW
Gate
(Note 3)
1" - 1 1/2"
VG-105
2" - 4"
VG-30
6" - 10"
VG-31
2" - 3"
VGL-30
4" - 8"
VGL-30E
1" - 1 1/2"
VR-139
2" - 10"
VR-48
1" - 1 1/2"
Globe
Check
Other
Flange
(Note 5)
Gasket
Stud
Nut
FLG-64
1" - 10"
WN (RTJ)
FLG-63
2" - 10"
2500
BLIND (RTJ)
JA-06
1" - 10"
2500
Octagonal
(Note 2)
3/4" - 2 1/2"
ASTM A 194 Gr 4/S3
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-44
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP.1-1
CLIENT:
SHEET:
E&P
TITLE:
2 of 2
CODE
Service
Temp.
Range
Corrosion
Allowance
ASME B31.3
-100C /
210C
_______
Class
2500
(Note 6)
Temp. (C)
from -100 up to 38
5000
210
3483
50
4837
100
4205
150
3794
200
3524
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
4 Use niple THD X PLAIN and threaded cap (TAM-18) after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
6 Maximum working pressure (-100C/210C).
8" - 3.180 psig
10" - 3.190 psig
7 When requerid Fully Tight Valve (VET), see types in appendix 14.
8 From -100C to -30C material shall de solution heat treated.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
Standard
H3
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
129 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
ASME B31.3
0C / 90C
(3,2 mm)
Class
2500
(Note 5)
Pipe
(Note 5)
Half Coupling
Wall or
Class
Ends
Material
T-05A
3/4"
XXS
PLAIN
T-02A
2" - 6"
XXS
BW
API 5L Gr B PSL 1
seamless
9000
SW
ASTM A 105
Short Nip.
XXS
PLAIN
API 5L Gr B PSL 1
seamless
Wall thickness
according to
pipe
BW
ML-14
3/4"
T-05A
Long Nip.
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
2" - 6"
H5
Valves
Size
(in)
Tag
Standard
Ball
(Note 4)
Size
Description
Tag
3/4"
VE-161D
2 1/16" - 4
1/16"
ASTM A 105
Gate
VG ABRAS-07
Globe
Check
2" - 6"
Flange
(Note 4)
Gasket
(Note 2)
Stud
Nut
FLG-20
WN (RTJ)
FLG-21
BLIND (RTJ)
2" - 6"
JA-02
2500
Octagonal
ASTM A 105
Other
(Note 2)
1" - 2"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VR-41
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
E&P
TITLE:
SHEET:
130 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
ASME B31.3
0C / 90C
(3,2 mm)
Class
2500
(Note 5)
up to 38
6170
50
6050
90
5600
Temp. (C)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 The flange FLG-(20) will be used as a counter flange of VG ABRAS-04 (FJA).
5 Maximum working pressure (0C/90C).
2" - 6000 psi
3" - 5900 psi
4" - 5150 psi
6" - 4550 psi
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
Standard
H5
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
131 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
ASME B31.3
0C / 175C
(Note 11)
(1,6 mm)
Item
Tag
Wall or
Class
2500
(Note 8)
Valves
Ends
Material
Class
Ball
Standard
H10
(Note 9)
(Note 4)
Size
Description
Tag
1" - 1 1/2"
VE-458
2" - 3"
VE-16
4" - 12"
VE-28
1" - 1 1/2"
VE-459
2" - 3"
VE-109
4" - 12"
VE-127
2" - 4"
VG-16
6" - 12"
VG-17
2" - 3"
VGL-19
4" - 8"
VGL-19E
1" - 1 1/2"
VR-136
2" - 12"
VR-41
1" - 1 1/2"
1" - 1 1/2"
T-02A
Pipe
XXS
BW
2" - 6"
API 5L Gr B PSL 1
seamless
8" - 10"
SCH 160
12"
1,250"
T-31
Equal Tee
TE-43
Red. Tee
TRE-39
Cross
CRUZ-36
Cap
TAM-41
ASTM A 105
1" - 1 1/2"
Short Nip.
API 5L Gr B PSL 1
seamless
T-02A
(Notes 1 and 6)
Long Nip.
Red.Nip.C
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
1" - 4"
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
S.R.ELL 90
CRC-20
L.R.ELL 90
CRL-09
L.R.ELL 45
CRL-10
Tee
TE-23
Red. Tee
TRE-17
Conc. Red.
REDC-05
Ecc. Red.
REDE-05
Cap
TAM-28
Cross
CRUZ-25
2" - 6"
Wall thickness
according to
pipe
Gate
BW
(Note 5)
ASTM A 105
2" - 12"
Globe
ASTM A 694 Gr F60
(Note 10)
8" - 12"
Check
FLG-20
Flange
(Note 7)
WN (RTJ)
1" - 6"
FLG-21
2500
FLG-89
WN (RTJ)
8" - 12"
FLG-106
Gasket
(Note 2)
BLIND (RTJ)
Octagonal
JA-02
1" - 12"
JI-05
Stud
Nut
(Notes 2)
(Notes 2 and
4)
(Notes 2)
(Notes 2 and
4)
Other
ASTM A 105
BLIND (RTJ)
2500
Oval
3/4" - 3"
ASTM A 193 Gr B7
3/4" - 3"
3/4" - 3"
ASTM A 194 Gr 2H
3/4" - 3"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-43
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
1 of 2
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 70C
(Note 9)
(1,6mm)
2500
H10P
Tag
T-05A
Pipe
(Note 9)
T-31
(Notes 1 and 4)
T-29
Elbow 90
JO-37
Elbow 45
JO-38
Equal Tee
TE-34
Red. Tee
TRE-34
Cross
CRUZ-28
Half Coupling
ML-14
Red. Coupling
LRE-12
Cap
TAM-31
Union
UN-19
Coupling
L-23
Short Nip.
Size
(in)
Wall or
Class
1/2"
3/4"
1"
1 1/2"
4" - PIGGABLE
0,337" SCH 80
6" - PIGGABLE
0,500"
8" - PIGGABLE
0,625"
10" - PIGGABLE
0,812"
12" - PIGGABLE
0,875"
24" - PIGGABLE
1,562"
9000
Valves (Note 7)
Ends
PLAIN
BW
5D.R.ELBOW
(PIGVEL)
C905D-06 (90)
Tee (PIG)
TE-42P
TRE-37P
Ball
(Note 3)
Size
Description
Tag
1/2" - 1 1/2"
VE-161D
4" - 12"
VE-28P
SW
ASTM A 105
PLAIN
API 5L Gr B PSL 1
seamless
1/2" - 1 1/2
T-05A
C903D-06 (90)
API 5L Gr B PSL 1
seamless
Long Nip.
3D.R.ELBOW
(PIGVEL)
Material
Gate
C453D-06 (45)
4" - 12"
Wall
thickness
according to
pipe
C455D-06 (45)
ASTM A 694 Gr F 65
(Note 8)
Globe
2" - 3"
VGL-19
4" - 8"
VGL-19E
Check
FLG-43
Flange
FLG-19
(Note 5)
FLG-89
SW (RTJ)
1/2" - 1 1/2"
4" - 12"
2500
FLG-106
Gasket
(Note 11)
Stud
Nut
WN (RTJ)
24"
JA-02
Octagonal
1/2" - 12"
JVM-02
ASTM A 694 Gr F 65
(Nota 8)
BLIND (RTJ)
2500
JI-05
IX Seal ring
WN (RTJ)
BLIND (RTJ)
FLG-158
(Note 2)
ASTM A 105
BLIND (RTJ)
24
Oval
Fenolic resin
___
(Note 2)
1/2" - 3 1/4"
ASTM A 193 Gr B7
(Notes 2 and 3)
1/2" - 3 1/4"
(Note 2)
1/2" - 3 1/4"
ASTM A 194 Gr 2H
(Notes 2 and 3)
1/2" - 3 1/4"
ASTM A 194 Gr 7
Other
1/2" - 1 1/2"
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-43
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
2 of 2
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
0C / 70C
(Note 9)
(1,6mm)
2500
H10P
from 10 up to 38
4000
70
4000
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and
ASTM A 194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
4 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
5 Flanges 1 1/2" may be used, if strictly necessary.
6 Isolating joint see drawing on the appendix 15.
7 When requerid Fully Tight valve (VET), see types in appendix 14.
8 Maximum carbon equivalent 0,42%.
In possibility of occurrence of low temperatures, shall be verified the need normalized, in accordance with Table 323.2.2 A of standard ASME
9
B31.3.
10 The transition between the ASME flanges and NORSOK L-005 flanges will be defined during the detail.
11 Compact flange in accordance with NORSOK L-005.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
132 of 134
CODE
Service
Temp. Range
Corrosion
Allowance
ASME B31.3
0C / 175C
(Note 11)
(1,6 mm)
Class
2500
(Note 8)
Standard
H10
(Note 8)
up to 38
6171
50
6058
100
5631
150
5448
175
5357
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 Maximum working pressure (0C/175C).
2" - 6.009 psi
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
133 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
ASME B31.3
PCW-Produced water
0C / 70C
______
Class
Standard
2500
H11
(Note 11)
Tag
T-05A
Size
(in)
Wall or
Class
1" - 1 1/2"
Ends
(Note 11)
T-02A
API 5L Gr B PSL 1
seamless
Elbow 90
JO-09
Elbow 45
JO-10
Equal Tee
TE-06
Red. Tee
TRE-03
Cross
CRUZ-06
Coupling
L-05
Half Coupling
ML-03
(Note 4)
Size
Description
Tag
1" - 1 1/2"
VE-192
2" - 3"
VE-194
4" - 12"
VE-196
2" - 4"
VG-76
6" - 12"
VG-77
2" - 3"
VGL-43
4" - 8"
VGL-43E
1" - 1 1/2"
VR-111
2" - 12"
VR-112
1" - 1 1/2"
2" - 6"
BW
T-32
Ball
PLAIN
XXS
Pipe
6" - 12"
Sch 160
6000
SW
ASTM A 105
1" - 1 1/2"
(Notes 1 and 6)
TAM-06
Union
UN-05
Short Nip.
API 5L Gr B PSL 1
seamless
T-05A
Long Nip.
Red.Nip.C
PLAIN
NIPRC-04
Red .Nip.E
NIPRE-10
Red.Nip.C
NIPRC-04A
Red .Nip.E
NIPRE-10A
S.R.ELL 90
CRC-01
L.R.ELL 90
CRL-01
L.R.ELL 45
CRL-02
Tee
TE-02
Red. Tee
TRE-01
Conc. Red.
REDC-01
Ecc. Red.
REDE-01
Cap
TAM-02
Cross
CRUZ-02
Weldolet
WOL-01
S.R.ELL 90
CRC-21
L.R.ELL 90
CRL-20
L.R.ELL 45
CRL-21
Tee
TE-22
Red. Tee
TRE-28
Conc. Red.
REDC-14
Ecc. Red.
REDE-13
Cap
TAM-30
Cross
Flange
(Note 7)
Gate
1" - 4"
BW/PLAIN
2" - 6"
Wall thickness
according to
pipe
Nut
ASTM A 105
Check
ASTM A 694 Gr F 70
(Note 8)
8"
CRUZ-27
FLG-20
2" - 4"
WN (RTJ)
FLG-21
1" - 4"
BLIND (RTJ)
ASTM A 105
2500
FLG-112
WN (RTJ)
6" - 12"
BLIND (RTJ)
JA-02
Octagonal
1" - 12"
JI-05
Stud
Globe
BW
2" - 8"
FLG-113
Gasket
(Note 2)
(Note 5)
2500
Oval
Other
ASTM A 694 Gr F 70
(Note 8)
(Notes 2)
3/4" - 3"
ASTM A 193 Gr B7
(Notes
2 and 4)
3/4" - 3"
(Notes 2)
3/4" - 3"
ASTM A 194 Gr 2H
(Notes
2 and 4)
3/4" - 3"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-33
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
134 of 134
CODE
Service
Temp.
Range
Corrosion
Allowance
ASME B31.3
0C / 70C
______
Class
2500
(Note 11)
Standard
H11
up to 38
6170
50
6050
70
5830
Temp. (C)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
4
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
7 Flanges 1 1/2" may be used, if strictly necessary.
8 Maximum carbon equivalent 0,42.
9 Isolating joint see drawing on the appendix 15.
10 When requerid Fully Tight valve (VET), see types in appendix 14.
11 Maximum working pressure (0C/70C).
6" - 5.611 PSI
8" - 5.417 PSI
10" - 5.395 PSI
12" - 5.298 PSI
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
1 of 2
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
TITLE:
CODE
Service
Temp. Range
Corrosion
Allowance
ASME B31.3
0C / 70C
______
Class
2500
(Note 4)
Tag
T-32
Pipe
T-32B
Short Nip.
Size
(in)
Wall or
Class
1"
1 1/2"
2"
3"
4"
6"
XXS 0,864"
8"
1,000"
10"
1,250"
12"
14"
2,000"
20"
Ends
Valves
Material
Standard
H14
(Note 5)
Ball
Size
Description
Tag
1" - 1 1/2"
VE-458
2" - 3"
VE-16
4" - 12"
VE-28
2" - 4"
VG-16
6" - 12"
VG-17
2" - 3"
VGL-19
4"
VGL-19E
1" - 1 1/2"
VR-136
2" - 8"
VR-41
1" - 1 1/2"
BW
T-32
Long Nip.
1" - 1 1/2"
Red. Nip. C
NIPRC-10
Red. Nip. E
NIPRE-17
Red. Nip. C
NIPRC-10A
Red. Nip. E
NIPRE-17A
Gate
1" - 4"
S. R. ELL 90 CRC-21
L. R. ELL 90
Wall thickness
according to
pipe
CRL-20
L. R. ELL 45
CRL-21
Tee
TE-22
Red. Tee
TRE-28
Conc. Red.
REDC-14
Ecc. Red.
REDE-13
Cap
TAM-30
Cross
CRUZ-27
Weldolet
WOL-09
BW
Globe
Check
Flange
FLG-118
Compact
FLG-155
Flange
(Notes 7 and 8) FLG-156
Gasket
(Note 2)
JA-02
2500
(Note 7)
Stud
Nut
JVM-02
BLIND
WN (RTJ)
BLIND
Octagonal
1" - 14"
and 20"
2500
JI-05
IX Seal ring
Other
WN (RTJ)
1" - 12"
FLG-119
1" - 20"
Oval
Fenolic resin
___
(Note 2)
3/4" - 2"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-43
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
2 of 2
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
TITLE:
CODE
Service
Temp. Range
Corrosion
Allowance
ASME B31.3
0C / 70C
_____
Class
2500
(Note 4)
up to 38
6170
50
6058
70
5888
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
4 Maximum working pressure (0C/70C).
4" - 6.145 psi
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
Standard
H14
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
1 of 2
CODE
Service
Temp.
Range
Corrosion
Allowance
ASME B31.3
-20C / 100C
(Note 11)
___
Pipes and Fittings (Coated with Inconel 625 - According appendix 21) (Note 8)
Item
Tag
T-02A
Pipe
(Note 9)
T-38A
T-38B
(Notes 1 and 6)
Equal Tee
TRE-35
Cross
CRUZ-28
Short Nip.
Wall or Class
1"
1 1/2"
2"
SCH 80 XS 0,218"
3"
SCH 80 XS 0,300"
4"
6"
8"
0,750"
10"
0,938"
12"
14"
16"
18"
20"
Ends
BW
(Note 4)
Description
Tag
1" - 1 1/2"
VE-450
4" - 12"
VE-451
VE-452
VE-467
ASTM A 105
1" - 1 1/2"
TAM-31
API 5L Gr B PSL 1
seamless
T-02A
Red. Nip. C
NIPRC-04
Red. Nip. E
NIPRE-10
1" - 4"
C903D-06 (90)
C453D-06 (45)
Tee
Ball
14" - 20"
Long Nip.
3D. R. ELBOW
H30
Size
2" - 3"
API 5L Gr X65 PSL 1
seamless
(Note 11)
(Note 9)
Material
API 5L Gr B PSL 1
seamless
2500
Standard
TE-34
Red. Tee
Cap
Size
(in)
Class
BW
Gate
TE-42
Red. Tee
TRE-36
Conc. Red.
REDC-17
Ecc. Red.
REDE-16
2" - 20"
ASTM A 694 Gr F 65
Cap
TAM-43
Cross
CRUZ-39
Weldolet
WOL-01
ASTM A 105
Butterfly
Globe
2" - 10"
FLG-21
Flange
(Note 13)
BLIND (RTJ)
1" - 1 1/2"
FLG-20
FLG-153
Gasket
JA-13
(Note 10)
Stud
JVM-01
(Note 2)
(Note 2)
VR-132
WN (RTJ)
ASTM A 694 Gr F 65
2" - 12"
VR-133
14" - 20"
VR-141
BLIND (MSJ)
14" - 20"
WN (MSJ)
1" - 12"
14" - 20"
1/2" - 2 1/2"
Nut
1 - 1 1/2"
2500
Octagonal
2500
IX Seal ring
ASTM A 105
BLIND (RTJ)
FLG-154
1/2" - 2 1/2"
VGL-92
Check
WN (RTJ)
2" - 12"
Other
Inconel 625
___
1" - 1 1/2"
ASTM A 193 Gr B7
ASTM A 193 Gr B16
ASTM A 194 Gr 2H
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-41
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
2 of 2
CODE
Service
Temp.
Range
Corrosion
Allowance
ASME B31.3
-20C / 100C
(Note 11)
___
Class
2500
(Note 9)
Standard
H30
up to 38
4000
50
4000
70
4000
100
4000
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and ASTM
A 194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
5 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
6 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
7 When requerid Fully Tight Valve (VET), see types in appendix 14.
8 All piping shall be internal Inconel 625 coated according Appendix 21.
9 Maximum working pressure (-20C/100C).
1 1/2" - 5.774 psi
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
1 of 2
CODE
Service
Temp.
Range
Corrosion
Allowance
0C / 100C
(Note 11)
___
Pipes and Fittings (Coated with Inconel 625 - According appendix 21) (Note 8)
Item
Tag
T-05A
Size
(in)
Wall or Class
1"
1 1/2"
Ends
Pipe
(Note 9)
BW
(Note 9)
H30P
Ball
(Note 4)
Size
Description
Tag
1" - 1 1/2"
VE-450
T-38A
2500
Standard
Material
API 5L Gr B PSL 1
seamless
Class
4" - 12"
14" - 20"
VE-452P
VE-467P
(Notes 1 and 6)
Equal Tee
TE-34
Red. Tee
TRE-34
Cross
CRUZ-28
Half Coupling
ML-14
Red. Coupling
LRE-12
Cap
TAM-31
Union
UN-19
Coupling
L-23
Short Nip.
ASTM A 105
1" - 1 1/2"
Wall
thickness
according to
pipe
T-05A
BW
API 5L Gr B PSL 1
seamless
Long Nip.
3D. R. ELBOW
(PIGVEL)
C903D-06 (90)
5D. R. ELBOW
(PIGVEL)
C905D-06 (90)
Tee (PIG)
TE-42P
C453D-06 (45)
4" - 20"
C455D-06 (45)
Gate
ASTM A 694 Gr F 65
(Note 11)
Butterfly
Globe
2" - 10"
FLG-21
Flange
(Note 13)
BLIND (RTJ)
1" - 1 1/2"
FLG-20
FLG-153
Gasket
JA-13
2" - 12"
(Note 10)
Stud
Nut
JVM-01
ASTM A 105
Check
BLIND (RTJ)
2500
WN (RTJ)
ASTM A 694 Gr F 65
BLIND (MSJ)
14" - 20"
WN (MSJ)
1" - 12"
Octagonal
2500
IX Seal ring
VGL-92
WN (RTJ)
FLG-154
1" - 20"
Other
Inconel 625
___
1" - 1 1/2"
(Note 2)
1/2" - 2 1/2"
ASTM A 193 Gr B7
(Notes 2 and 4)
1/2" - 2 1/2"
(Note 2)
1/2" - 2 1/2"
ASTM A 194 Gr 2H
(Notes 2 and 4)
1/2" - 2 1/2"
ASTM A 194 Gr 7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-41
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
2 of 2
CODE
Service
Temp.
Range
Corrosion
Allowance
0C / 100C
(Note 11)
___
Class
2500
(Note 9)
Standard
H30P
up to 38
4000
50
4000
70
4000
100
4000
Temp. (C)
Branch Connections
(Note 3)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and ASTM A
194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
5 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
6 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
7 When requerid Fully Tight Valve (VET), see types in appendix 14.
8 All piping shall be internal Inconel 625 coated according Appendix 21.
9 Maximum working pressure (0C/100C).
1 1/2" - 5.774 psi
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
1 of 2
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
TITLE:
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 38C
(3,2 mm)
10000 psi
J5
Pipe
Short Nip.
Tag
T-32A
T-32
T-32A
Size
(in)
3/4"
Wall or
Class
XXS
Valves
Ends
BW
2" - 6"
3/4"
XXS
CRC-21
L.R.ELL 90
CRL-20
L.R.ELL 45
CRL-21
Tee
TE-22
Red. Tee
TRE-28
2" - 6"
Wall thickness
according to
pipe
Conc. Red.
REDC-14
Ecc. Red.
REDE-13
Cap
TAM-30
Cross
CRUZ-27
Weldolet
WOL-09
Ball
(Note 4)
Size
Description
Tag
3/4"
VE-470
API 5L Gr B PSL 1
seamless
Long Nip.
S.R.ELL 90
Material
BW
ASTM A 234 Gr WPB
ASTM A 105
Gate
2 1/16" - 4
1/16"
Globe
Check
2" - 6"
Flange
(Note 4)
Gasket
(Note 2)
Stud
Nut
FLG-20
WN (RTJ)
FLG-21
BLIND (RTJ)
2" - 6"
JA-02
2500
Octagonal
ASTM A 105
Other
(Note 2)
1" - 2"
ASTM A 194 Gr 2H
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VR-142
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
2 of 2
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
CODE
Service
Temp.
Range
Corrosion
Allowance
Class
Standard
ASME B31.3
0C / 38C
(3,2 mm)
10000 psi
J5
up to 38
10000
Temp. (C)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
1 of 2
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
CODE
Service
Temp. Range
ASME B31.3
0C / 65C
(Note 8)
Tag
(Notes 1 and 2)
T-17
1/2" - 1 1/2"
Wall or
Class
Sch 80S
T-19
Elbow 90
JO-39
Elbow 45
JO-40
Equal Tee
TE-35
Red. Tee
TRE-30
Cross
CRUZ-29
Coupling
L-24
Half Coupling
ML-16
Red. Coupling
LRE-13
Cap
TAM-32
Union
UN-20
2" - 6"
Standard
10000
(Note 7)
J12
Valves
Material
PLAIN
Sch 160
BW
9000
SW
Ball
Size
Description
2 1/16" - 3 1/16"
4 1/16" - 5 1/8"
Tag
1/2" - 1 1/2"
T-17
Long Nip.
Red.Nip.C
Ends
Class
Pipe
(Note 7)
Short Nip.
Size
(in)
Corrosion
Allowance
PLAIN
NIPRC-09
Red .Nip.E
NIPRE-15
Red.Nip.C
NIPRC-09A
Red .Nip.E
NIPRE-15A
S.R.ELL 90
CRC-06
L.R.ELL 90
CRL-13
L.R.ELL 45
CRL-14
Tee
TE-25
Red. Tee
TRE-19
Conc. Red.
REDC-07
Ecc. Red.
REDE-07
Cap
TAM-27
Cross
CRUZ-21
Weldolet
WOL-05
Gate
1/2" - 4"
BW/PLAIN
Wall thickness
according to
pipe
(Note 6)
VG-87
ASTM A 815
(UNS S32760)
2" - 6"
BW
Globe
2" - 6"
Check
FLG-114
FLG-115
Flange
(Note 3)
FLG-116
Gasket
JA-08
1/2" - 1 1/2"
1/2" - 6"
Stud
(Notes 9)
1/2" - 6"
Nut
API
10000
Octogonal tp BX
Fenolic resin
ASTM A 193 Gr B7
1/2" - 6"
3/4" - 1 1 /2"
Other
1/2" - 1 1/2"
3/4" - 1 1 /2"
WN (RTJ)
BLIND (RTJ)
(Note 11)
JI-05
SW (RTJ)
API
10000
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-34
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
2 of 2
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
CODE
Service
Temp. Range
ASME B31.3
0C / 65C
(Note 8)
Corrosion
Allowance
Class
10000
(Note 7)
Standard
J12
Up to 38
11250
65
11000
Temp. (C)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use niple THD X PLAIN and threaded cap (TAM-) after drains and vents blocking.
3 Flanges 1 1/2" may be used, if strictly necessary.
4 Use only when recommended by Appendix 5.
5 See Appendix 16 - Welding qualification requirements for super duplex.
6 See Appendix 17 - Minimum requirements for valves casted in super duplex.
7 Max. pressure (0C/65C) - 7200 PSIG.
8 In possibility of occurrence of low temperatures, this spec can be used in accordance with table A-1 of ASME B31.3 standard.
9 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
10 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM
A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
11 Isolating joint see drawing on the appendix 15.
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
1 of 2
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
TITLE:
CODE
Temp. Range
Corrosion
Allowance
ASME B31.3
-70C / 123C
(1,6 mm)
Class
10000
(Note 12)
Tag
T-40
Pipe
(Notes 8 and 11)
(Notes 1 and 2)
Equal Tee
Wall or
Class
1"
1 1/2"
2"
3"
4"
6"
8"
XXS 0,875"
10"
12"
1,250"
14"
TRE-38
Cross
CRUZ-35
Cap
TAM-40
Valves (Note 7)
Ends
Material
Ball
Size
BW
Description
Tag
ASTM A 333 Gr 8
seamless
(Note 8)
T-40
Long Nip.
Red. Nip. C
NIPRC-13
Red. Nip. E
NIPRE-20
S. R. ELL 90
CRC-23
L. R. ELL 90
CRL-32
L. R. ELL 45
CRL-33
Equal Tee
TE-43
Red. Tee
TRE-38
Conc. Red.
REDC-16
Ecc. Red.
REDE-15
Cap
TAM-40
Cross
CRUZ-35
Weldolet
J31
TE-43
Red. Tee
Short Nip.
Size
(in)
Standard
1" - 4"
Gate
Wall thickness
according to pipe
BW
Globe
4" - 6"
VGL-94
WOL-08
Check
1" - 14"
API 10000
BLIND (MSJ)
WN (MSJ)
Other
1" - 1 1/2"
IX Seal ring
(Note 5)
Stud
Nut
JVM-02
(Notes 4 and
6)
1/2" - 14"
1/2" - 2"
API 10000
Inconel 625
ASTM A 320 Gr L7
ASTM A 194 Gr 4/S3
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-42
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
2 of 2
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
CODE
Temp. Range
Corrosion
Allowance
ASME B31.3
-70C / 123C
(1,6 mm)
Class
10000
(Note 12)
Temp. (C)
80000
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use niple THD X PLAIN and threaded plug after drains and vents blocking.
3 Flanges 1 1/2" may be used, if strictly necessary.
4 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
5 Compact flange in accordance with NORSOK L-005.
6 Bolts and nuts in accordance with NORSOK M-001.
7 When requerid Fully Tight Valve (VET), see types in appendix 14.
8 Charpy impact test is required for low temperature services materials in accordance ASTM A 333.
9 Charpy impact test is required for low temperature services materials in accordance ASTM A 420.
10 Charpy impact test is required for low temperature services materials in accordance ASTM A 522.
11 High pressure piping according to Chapter IX and appendix K of ASME B31.3.
12 For pressure exceed standard L-005, design according manufacturer.
13 Pressure / Temperature Rating shall be informed by the vendor and approved by PETROBRAS.
Standard
J31
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
1 of 2
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
TITLE:
CODE
Temp. Range
Corrosion
Allowance
-70C / 123C
(1,6 mm)
Class
10000
(Note 12)
Pipe
(Notes 1 and 2)
Equal Tee
Tag
T-40
Size
(in)
Wall or
Class
1"
1 1/2"
4"
6"
0,625"
8"
Standard
J31P
Valves (Note 7)
Ends
Material
Ball
Size
BW
Description
Tag
ASTM A 333 Gr 8
seamless
(Note 8)
TE-43
Red. Tee
TRE-38
Cross
CRUZ-35
Cap
Short Nip.
TAM-40
ASTM A 333 Gr 8
seamless
(Note 8)
T-40
Long Nip.
Red. Nip. C
NIPRC-13
Red. Nip. E
NIPRE-20
S. R. ELL 90
CRC-23
L. R. ELL 90
CRL-32
L. R. ELL 45
CRL-33
Equal Tee
TE-43
Red. Tee
TRE-38
Conc. Red.
REDC-16
Ecc. Red.
REDE-15
Cap
TAM-40
Cross
CRUZ-37
Weldolet
WOL-08
1" - 4"
Gate
Wall thickness
according to
pipe
BW
Globe
4" - 6"
VGL-94
Check
FLG-149
1" - 14"
API 10000
FLG-150
BLIND (MSJ)
WN (MSJ)
Compact Flange
(Notes 5 and 11)
IX Seal ring
(Note 5)
Stud
Nut
Other
1" - 1 1/2"
JVM-02
(Notes 4 and
6)
1/2" - 8"
1/2" - 1 1/2"
API 10000
Inconel 625
ASTM A 320 Gr L7
ASTM A 194 Gr 4/S3
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VAG-42
N:
REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
E&P
TITLE:
2 of 2
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
CODE
Temp. Range
Corrosion
Allowance
-70C / 123C
(1,6 mm)
Class
10000
(Note 12)
Temp. (C)
8000
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use niple THD X PLAIN and threaded plug after drains and vents blocking.
3 Flanges 1 1/2" may be used, if strictly necessary.
4 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
5 Compact flange in accordance with NORSOK L-005.
6 Bolts and nuts in accordance with NORSOK M-001.
7 When requerid Fully Tight valve (VET), see types in appendix 14.
8 Charpy impact test is required for low temperature services materials in accordance ASTM A 333.
9 Charpy impact test is required for low temperature services materials in accordance ASTM A 420.
10 Charpy impact test is required for low temperature services materials in accordance ASTM A 522.
11 For pressure exceed standard L-005, design according manufacturer.
12 Maximum working pressure (-70C/123C).
4" - 7.686 psi
6" - 7.888 psi
13 Pressure / Temperature Rating shall be informed by the vendor and approved by PETROBRAS.
Standard
J31P
N:
TECHNICAL SPECIFICATION
I-ET-3000.00-1200-200-PCI-001
CLIENT:
SHEET:
1 of
4
E&P
PROGRAM:
PIPING MATERIAL - STANDARDIZATION
REA:
ET-200.03
E&P - ENGP
TITLE:
APPENDIX 1
Connection Details for Temperature Wells
SPEC
Type of Installation
Curved
Vertical/Horizontal
Diam. 3/4"
Diam. 1
Diam.
Diam. 1 Flg
threaded
Flg
threaded
Type 1A
Type 1B
Type 1C
Type 1D
Type 1E
Pipe Diameter
- 1
2
3 - 4
- 2
3 - 4
A4
A8
B3
B4
B5
B6
- 1
B7
B7R
B9
B10
B11
B12
B14
B15
C3
C4
2
C5
C6
C8
C9
C10
C12
C14
E3
E4
E5
E6
E6R
E8
3 and greater
E9
E10
E10R E10P
E14
F3
F4
F5
F6
F6R
F10 F10R
- 2
F10P F14
G3
G4
G5
G6
G6R
G10
G10P G10R
G11
G12
3 and greater
G12P G14
H3
H5
H10
H11
Date
Project
Execution
Verification
Approval
Type 2A
Type 2B
Type 2C
Type 2D
Type 2E
Original
REV. D
REV. E
REV. F
REV. G
REV. H
REV. J
REV. K
REV. L
Nov/81
DEPRO
M.Assayag
Hernon
Hernon
Oct/95
E&P
Fernando
Hernon
Hernon
Sep/04
E&P
Gerson
Fernando
Hernon
Nov/05
E&P
Gerson
Fernando
Joper
Dec/05
E&P
Gerson
Fernando
Joper
Jan/06
E&P
Gerson
Fernando
Joper
Mar/06
E&P
Gerson
Fernando
Joper
May/06
E&P
Gerson
Fernando
Joper
Feb/07
E&P
Gerson
Fernando
Joper
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORM N-381 REV. F
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
2
TITLE:
APPENDIX 1
Connection Details for Temperature Wells
B20
B21
B22
B23
B24
B25
REV.
of
L
4
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
3
TITLE:
APPENDIX 1
Connection Details for Temperature Wells
THREADED THERMOWELLS
REV.
of
L
4
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
4
TITLE:
APPENDIX 1
Connection Details for Temperature Wells
FLANGED THERMOWELLS
REV.
of
L
4
N:
TECHNICAL SPECIFICATION
I-ET-3000.00-1200-200-PCI-001
CLIENT:
SHEET:
1 of
9
E&P
PROGRAM:
PIPING MATERIAL - STANDARDIZATION
REA:
ET-200.03
E&P - ENGP
TITLE:
APPENDIX 2
Connection Details for Drains and Vents
1 Drains:
Spec
A4
A8
B3 C3 E3
B4 C4 E4
B5 C5 E5
B6
C6 E6 E6R
B7
B7R
B9
C9
Pipe Diameter
- 1
2 - 4
6 - 10
12 - 24
- 1
2 - 4
6 - 10
12
- 1
2 - 4
6 - 10
12 - 34
- 1
2 - 4
6 - 10
12 - 24
2 - 6
- 1
2 - 4
6 - 10
12 - 24
1 - 1
2 - 4
6 - 10
12 - 36
- 1
2 - 4
6 - 10
12 - 36
E9
B10
Drain Type
I
II
II
II
III
IV
IV
IV
III
IV
IV
IV
III
IV
IV
IV
VII
III
IV
IV
IV
VI
V (*)
II
II
II
III
IV
IV
IV
Drain Diameter
1
1
1
1
1
1
1
1
2 1/16
1
1
1
1
1
1
C10
Project
Execution
Verification
Approval
VG-36
VE-04B
VE-58 / VE-61
VG-45
VG ABRAS-04
VE-91B/VE-91C
VE-64B/VE-64C
VE-91B / VE-91C
VG-36
VE-04B / VE-04D
VE-48B / VE-48D
VE-101B/VE-101D
VE-48D/VE-04D
VE-101D
VE-04B/VE-04C
VE-174C/VE178C/VE-182C
VE-48B/VE-48C
B11
Date
Valves
Original
REV. D
REV. E
REV. F
REV. G
REV. H
REV. J
REV. K
REV. L
Nov/81
DEPRO
M.Assayag
Hernon
Hernon
Oct/95
E&P
Fernando
Hernon
Hernon
Sep/04
E&P
Gerson
Fernando
Hernon
Nov/05
E&P
Gerson
Fernando
Joper
Dec/05
E&P
Gerson
Fernando
Joper
Jan/06
E&P
Gerson
Fernando
Joper
Mar/06
E&P
Gerson
Fernando
Joper
May/06
E&P
Gerson
Fernando
Joper
Feb/07
E&P
Gerson
Fernando
Joper
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORM N-381 REV. F
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
2
REV.
of
L
9
TITLE:
APPENDIX 2
Connection Details for Drains and Vents
1 Drains: (continued)
Spec
E10 E10P
E10R
Pipe Diameter
Drain Type
Drain Diameter
Valves
VE-101B/VE-101C
- 1
2 - 4
6 - 10
12 - 24
III
IV
IV
IV
1
1
B14
C14
E14
2 - 10
12 - 36
VII
VII
1
1
VE-44
VE-45
VE-46
B15
- 1
2 - 4
6 - 10
12 - 36
III
IV
IV
IV
1
1
VE-04C
B12
C12
VE-04B
VE-75 / VE-80
B20
B21
B25
VE-159
VE-160
VE-158
VG-02
C8
E8
F3
G3
F4
G4
F5
F6
F6R
G6
G6R
- 1
2 - 4
6 - 8
- 1
2 - 4
6 - 10
- 1
2 - 4
6 - 10
12 - 18
I
II
II
III
IV
IV
III
IV
IV
IV
1
1
2 - 6
VII
2 1/16
VG ABRAS-05
- 1
2 - 4
6 - 10
- 1
2 - 4
6 - 10
12 - 18
III
IV
IV
III
IV
IV
IV
1
1
VE-94B/VE-94C
VE-01
VE-59 / VE-62
VE-60B/VE-63B
VG-46
VE-94D
VE-05B/VE-05C
VE-102B/VE-102C
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
3
REV.
of
L
9
TITLE:
APPENDIX 2
Connection Details for Drains and Vents
1 Drains: (continued)
Spec
F14
G14
G5
G10
G10P
G10R
Pipe Diameter
2 - 10
12 - 18
Drain Type
VII
VII
Drain Diameter
1
1
Valves
2 - 6
VII
2 1/16
VG ABRAS-06
- 1
2 - 4
6 - 10
12 - 20
III
IV
IV
IV
1
1
VE-43D / VE-49D
VE-102D
G11
G12
G12P
H3
H5
H10
H11
VE-47
VE-43D/VE-102D
VE-186D/VE-189D
- 1
2 - 4
6 - 10
12 - 20
- 1
2 - 4
6 - 10
2 - 6
- 1
2 - 4
6 - 8
- 1
2 - 3
4 - 12
III
IV
IV
IV
III
IV
IV
VII
III
IV
IV
III
IV
IV
1
1
1
2 1/16
VE-168/VE-171
VE-171
VE-60C / VE-63C
VG ABRAS-07
VE-161D/VE-162D
VE-192/VE-193
(*) Type V For piping ND 1, instead of reduction coupling, use reduction tee 1 x .
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
4
TITLE:
APPENDIX 2
Connection Details for Drains and Vents
1 Drains
REV.
of
L
9
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
5
TITLE:
APPENDIX 2
Connection Details for Drains and Vents
REV.
of
L
9
N:
TECHNICAL SPECIFICATION
E&P
I-ET-3000.00-1200-200-PCI-001
SHEET:
6
REV.
of
L
9
TITLE:
APPENDIX 2
Connection Details for Drains and Vents
2 Vents:
Spec
A4
A8
B3
C3
E3
B4
C4
E4
B5
C5
E5
B6
C6 E6 E6R
B7
B7R
Vent Type
I
II
III
IV
III
IV
III
IV
Vent Diameter
C10
E9
2 - 6
VI
2 1/16
- 1
2
III
IV
VE-91B/VE-91C
VE-64B/VE-64C
VE-91B/VE-91C
- 1
2
I
II
VG-36
- 1
2
VE-04B
VE-58 /VE-61
VG-45
III
IV
VE-101B/VE-101C
- 1
2
III
IV
B14
C14
E14
1 - 1
2
VII
VI
B15
- 1
2
III
IV
B12
C12
VG ABRAS-04
VE-04B/VE-04C
VE-04D
VE-48B/VE-48C
VE-48D
Valves
VG-36
B10
B9
C9
Pipe Diameter
- 1
2
- 1
2
- 1
2
- 1
2
VE-101D
VE-174C/VE178C/VE-182C
VE-75/VE-80
VE-44
VE-45
VE-46
VE-04C
B20
B21
B25
VE-159
VE-160
VE-158
VG-02
C8
E8
F3
G3
F4
G4
- 1
2
- 1
2
- 1
2
I
II
III
IV
III
IV
VE-01
VE-59/VE-62
VE-60B/VE-63B
VG-46
N:
TECHNICAL SPECIFICATION
E&P
I-ET-3000.00-1200-200-PCI-001
SHEET:
7
REV.
of
L
9
TITLE:
APPENDIX 2
Connection Details for Drains and Vents
2 Vents: (continued)
Spec
F5
F6
F6R
G6
G6R
F10 F10R F10P
F14
G14
G5
G10
G10P
G10R
G11
G12
G12P
H3
H5
H10
H11
Pipe Diameter
2 - 6
- 1
2
- 1
2
Vent Type
VI
III
IV
III
IV
Vent Diameter
2 1/16
VI
2 - 6
- 1
2
VI
III
IV
2 1/16
- 1
2
- 1
2
2 - 6
- 1
2 - 8
- 1
2
III
IV
III
IV
VI
III
IV
III
IV
Valves
VG ABRAS-05
VE-94B/VE-94C
VE-94D
VE-05B/VE-05C
VE-102B/VE-102C
VE-47
VG ABRAS-06
VE-43D/VE-49D
VE-102D
VE-186D/VE-189D
VE-168/VE-171
VE-171
VE-60C/VE-63C
2 1/16
VG ABRAS-07
VE-161D/VE-162D
VE-192/VE-193
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
8
TITLE:
APPENDIX 2
Connection Details for Drains and Vents
2 - Vents
REV.
of
L
9
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
9
TITLE:
APPENDIX 2
Connection Details for Drains and Vents
REV.
of
L
9
N:
TECHNICAL SPECIFICATION
I-ET-3000.00-1200-200-PCI-001
CLIENT:
SHEET:
3
E&P
1 of
PROGRAM:
PIPING MATERIAL - STANDARDIZATION
REA:
ET-200.03
E&P - ENGP
TITLE:
APPENDIX 3
Connection Details for Pressure Instruments
Spec
A4
A8
B3
C3
E3
B4
C4
E4
B5
C5
E5
B6
C6
E6
E6R
B7
B9
B7R
C9
E9
E10R
B11
B12
C12
B14
C14
E14
B15
Pipe Diameter
- 1
2
- 1
2
- 1
2
- 1
2
2"
- 1
2
- 1
2
- 1
2
- 1
2"
- 1
2"
Type
I
II
III
IV
III
IV
III
IV
IV
III
IV
PI Diameter
VG-36
VE-04
VE-58/VE-61
VG-45
VE-48D
VE-64C/VE-91
Date
Project
Execution
Verification
Approval
B23
VG-01
III
IV
III
IV
III
IV
- 1
2"
III
IV
1 - 1
2
1 - 1
2
1 - 1
2
- 1
2
III
IV
III
IV
III
IV
III
IV
VE-04D/VE-48D
VE-101D
VE-04C/VE-48C
VE-101B/VE-101C
VE-48B
VET-174C/VE178C/VE-182C
VE-75/VE-80
VE-44
1
VE-45
VE-46
VE-04C
B20
B21
B25
B22
Valves
VE-159
VE-160
VE-158
VG-02
B24
Original
REV. D
REV. E
REV. F
REV. G
REV. H
REV. J
REV. K
REV. L
Nov/81
DEPRO
M.Assayag
Hernon
Hernon
Oct/95
E&P
Fernando
Hernon
Hernon
Sep/04
E&P
Gerson
Fernando
Hernon
Nov/05
E&P
Gerson
Fernando
Joper
Dec/05
E&P
Gerson
Fernando
Joper
Jan/06
E&P
Gerson
Fernando
Joper
Mar/06
E&P
Gerson
Fernando
Joper
May/06
E&P
Gerson
Fernando
Joper
Feb/07
E&P
Gerson
Fernando
Joper
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY N-381 REV. F
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
2
REV.
of
TITLE:
APPENDIX 3
Connection Details for Pressure Instruments
Spec
C8
E8
F3
G3
F4
G4
F5
G5
F6
F6R
G6
G6R
G14
Pipe Diameter
- 1
2
- 1
2
- 1
2
- 1
2
2
- 1
2
- 1
2
- 1
2
- 1
2
- 1
2
Type
III
IV
III
IV
III
IV
III
IV
IV
III
IV
III
IV
III
IV
III
IV
III
IV
- 1
2
III
IV
- 1
2
2
- 1
2
- 1
2
III
IV
IV
III
IV
III
IV
PI Diameter
Valves
VE-01
VE-59/VE-62
VE-60B/VE-63B
VG-46
VE-49D
VE-94B/VE-94C
VE-94D
VE-05C/VE-102C
VE-47
VE-43D/VE-49D
VE-102D
VE-186D/VE189D
VE-168/VE-171
VE-171
VE-60C/VE-63C
VE-161D
VE-161D
VE-192/VE-193
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
3
TITLE:
APPENDIX 3
Connection Details for Pressure Instruments
REV.
of
N:
TECHNICAL SPECIFICATION
I-ET-3000.00-1200-200-PCI-001
CLIENT:
SHEET:
1 of
2
E&P
PROGRAM:
PIPING MATERIAL - STANDARDIZATION
REA:
ET-200.03
E&P - ENGP
TITLE:
APPENDIX 4
Connection Details for Orifice Flange
Spec
Valve
Diameter
Code
A4
VG-36
A8
VE-04B
B3
B4
B6
E6
B7
C3
C3
B9
C9
VE-58 / VE-61
VG-45
VE-64C/VE-91C
E3
E4
C6
E6R
B7R
E9
VE/101B/VE-101C
VE-48B
VE-174C/VE178C/VE-182C
E10R
B11
B12
VG-01
VE-04D/VE-48D
VE-101D
VE-04C/E-48C
VE-75 / VE-80
C12
VE-04C
B15
B20
B21
B25
B22
B23
B24
C8
E8
F3
G3
VE-60B / VE-63B
F4
G4
F6
G6
F6R
G6R
F10
Date
Project
Execution
Verification
Approval
VE-01
VE-59 / VE-62
VG-46
F10R F10P
VE-94C
VE-94D
VE-05C/VE-102C
Original
REV. D
REV. E
REV. F
REV. G
REV. H
REV. J
REV. K
REV. L
Nov/81
DEPRO
M. Assayag
Hernon
Hernon
Oct/95
E&P
Fernando
Hernon
Hernon
Sep/04
E&P
Gerson
Fernando
Hernon
Nov/05
E&P
Gerson
Fernando
Joper
Dec/05
E&P
Gerson
Fernando
Joper
Jan/06
E&P
Gerson
Fernando
Joper
Mar/06
E&P
Gerson
Fernando
Joper
May/06
E&P
Gerson
Fernando
Joper
Feb/07
E&P
Gerson
Fernando
Joper
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORM N-381 REV. F
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
2
REV.
of
TITLE:
APPENDIX 4
Connection Details for Orifice Flange
Spec
Valve
Diameter
G10
G10P
VE-43D/VE-49D
VE-102D
G10R
G11
G12
G12P
Code
VE-43D/VE-102D
VE-186D/VE-189D
VE-168 / VE-171
VE-171
H3
VE-60C/VE-63C
H10
VE-161D/VE-162D
H11
VE-192/VE-193
Note: For Specs B14; C14; E14; F14 and G14 its not recommended orifice
flanges use. In this lines, the flow tapes shall be installed at stainless steel
AISI-316 spacers rings.
N:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
1
E&P
PROGRAM:
PIPING MATERIAL - STANDARDIZATION
REA:
ET-200.03
E&P - ENGP
TITLE:
11
of
APPENDIX 5
REV. 0
REV. A
REV. B
REV. C
REV. D
REV. E
REV. F
REV. G
Nov/81
DEPRO
M. Assayag
Hernon
Hernon
Mar/91
DEPRO
Jeter
Froes
Hernon
Oct/95
E&P
Fernando
Hernon
Hernon
Apr/00
E&P
Fernando
Hernon
Hernon
Sep/04
E&P
Lopes
Fernando
Hernon
May/06
E&P
Lopes
Fernando
Hernon
Feb/07
E&P
Lopes
Fernando
Hernon
Sep/09
E&P
Alvaro
Fernando
Claudio
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORM N-381 REV. F
REV. H
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
TITLE:
APPENDIX 5
Corrosiveness of Fluid and Gaseous Hydrocarbons and Produced Water
The increase to the solubility of the CO2 in the water is directly proportional to the
increase in pressure and inversely proportional to the increase in temperature.
The mineral salts in the water may prevent reduction of the pH level.
In reservoirs which produce natural gas, condensate and water containing low levels
of mineral salts, pressure is the main factor for controlling the solubility of the CO2.
For this reason, the partial pressure of the CO2 in the gaseous mixture is used to
determine the degree of corrosiveness.
The partial pressure of a given gas in a mixture is the pressure which would be
exerted in the event only the aforesaid gas was present, at the same temperature
and total volume occupied by the mixture.
The partial pressure of each component is equal to the total pressure of the system
multiplied by the molar fraction of the component (% in volume). In the case of the
partial pressure of CO2 (PCO2) the expression is the following:
PCO2 = Total Pressure x Molar Fraction of CO2 in the gas phase
1.3 - Hydrogen Sulfide Gas - H2S
The hydrogen sulfide gas is soluble in water, forming a weak acid, which causes
corrosion and helps allows atomic hydrogen to penetrate the metals.
The general reaction for this kind of corrosion may be denoted by the formula:
H2S 2H+ + S2Fe + 2H+ Fe2+ + H2
Fe2+ + S2- FeS
_____________________________________________________________
Fe + H2S FeS + H2
The ferrous sulfate produced under this reaction generally adheres to the surface of
the steel in the form of a black powder or scaling. This FeS scaling acts as a cathode
on the steel, resulting in pitting corrosion.
The most serious problem probably entails the penetration of the atomic hydrogen
produced on the steel, where some of these hydrogen atoms react, forming
hydrogen gas on the interfaces between the inclusions and the metal. Hydrogen gas
accumulating in the defects to the crystalline structure, especially in the region
surrounding the grains or metal/inclusion interfaces, will produce high internal
pressures, which could cause fractures or bubbles in the metal, provoking the stress
corrosion cracking or reducing the fatigue life of the material.
11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
TITLE:
APPENDIX 5
Corrosiveness of Fluid and Gaseous Hydrocarbons and Produced Water
+
2H + 2e 2HAdsorbed
2HAdsorbed H2
In the same way as the case of CO2, the pressure is a factor of control of the
solubility of H2S in the medium in which this gas is dissolved. For this reason, the
partial pressure of H2S (pH2S) in the gaseous mixture is also used to determine the
corrosiveness level, associated or not to the partial pressure of CO2.
PH2S = Total Pressure x Molar Fraction of H2S in the gas phase
The following relations are recommended to evaluate the corrosiveness of a gas,
based on the H2S content:
The gas is considered corrosive when the partial pressure of H2S in the gas mixture
is higher than 0.05 psia (Ref. 3). This criteria is used to good effect by many gas
distributing companies operating in the USA.
Another parameter for verification of the corrosiveness level with regard to the
Sulfide Stress Cracking (SCC) is the use of the correlations showed in Figures 1 and
2, which consider the partial pressures of H2S and CO2, the pH of the medium and
hardness of the exposed material (Ref.3). For a good estimate of the pH, a software
or a chemical model capable to calculate the pH based on the partial pressures of
the gases and the chemical composition of the water can be used.
11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
TITLE:
APPENDIX 5
Corrosiveness of Fluid and Gaseous Hydrocarbons and Produced Water
Indicative Sequences for Selecting the Piping Material standard
3.1 Gas Piping
GAS FLOWDIAGRAM
of
11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
TITLE:
APPENDIX 5
Corrosiveness of Fluid and Gaseous Hydrocarbons and Produced Water
3.2 Oil/Gas/Produced Water Piping
MULTIPHASE FLOW (oil/water/gas) FLOWDIAGRAM
of
11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
11
TITLE:
APPENDIX 5
Corrosiveness of Fluid and Gaseous Hydrocarbons and Produced Water
3.3 - Produced Water Piping
Maximum
Temperature
Spec
Material
Qualified Coatings
Observations
60oC
B25
RPVC
Onshore
Installations
65 C
B11 C11
E11 F11
G11 H11
90 C
120 C
B11
150oC
CS + Organic
Coating
(Appendix 18)
Belzona 1391
Resinar Flake Glass 500 N
Nova Coating IPC Magna
Ciapowder 401
Offshore and
Onshore
Installations
Belzona 1522
Chesterton ARC 855 HT
Resinar Flake Glass 500 EN
Nova Coating IPC ME35
Sauereisen Fibrecrete 218
Hallar 9414
Hallar 6614 + 6014
DuPont XF
Scothkote 134
Obs: The qualified products for application in higher temperatures can be used in lower
temperatures.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
TITLE:
APPENDIX 5
Corrosiveness of Fluid and Gaseous Hydrocarbons and Produced Water
Note:
(1) B3, C3, E3, F3, G3, H3. (316L)
(2) B6, C6, E6, F6, G6. (A 333 Gr. 6)
(3) B9, C9, E9. (API 5L Gr. B), F3, G3. (321)
(4) B10, C10, E10, F10, G10, G10P. (API 5L Gr. B).
(5) B12, C12, G12, J12 (Super Duplex Stainless Steel)
(6) B25 (RPVC)
(7) Carbon Steel API 5L grade B + Liner (or Clad) Inconel alloy 625.
(8) CO2 corrosion rate shall be calculated according to program for evaluation and
determination of corrosion of steels NORSOK M-506. The NORSOK software for
corrosion rate is available on site http://www.standard.no/imaker.exe?id=1369)
(9) ACR - Annual Corrosion Rate (mm/year); HAZ Heat Affected Zone
(10) Requirements for Carbon Steel materials and equipment for services with H2S:
a) Materials and equipment shall fully comply with the requirements of NACE
MR0175, NACE TM 0177 and NACE TM0284;
b) At least three rows of tests shall be accomplished in the case of NACE TM 0177
and NACE TM 0284;
c) For each test condition, set in the standard, at least three samples shall be tested;
d) At least two of the three samples shall be considered approved;
e) In the case of the NACE TM 0177, the test shall be performed for at least thirty
days, with continuous H2S bubbling;
f) Regarding NACE TM 0284, the A Solution shall be used. The maximum
acceptable CLR index shall be 1% and the maximum acceptable CTR index shall be
0,5%.
g) Considering NACE TM0177, the B Solution shall be chosen. The test shall be
performed using the A Method for the base metal and C Method for the welded
joint. The applied load shall correspond to 90% of yield limit specified for the base
metal and 85% of the yield limit for the welded joint;
h) The qualification of all welding procedures shall include the tests fixed in items E
and G of this specification;
i) During the qualification of the welding procedure, the Vickers hardness profile shall
be recorded with a 5Kg load (HV5) over the thermally zone (HAZ) of the welded joint
and the highest value found shall be identified;
j) For the tests according to NACE TM0177, samples with the Maximum Equivalent
Carbon, the highest yield stress and the highest hardness shall be chosen;
k) The welding of specimens shall be performed with the heat input of at least 90%
of the heat input specified in the qualified welding procedure;
l) The welding fillets shall be performed always from the base metal to the welding
metal so that to temper the thermally affected zone (HAZ);
11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
TITLE:
APPENDIX 5
Corrosiveness of Fluid and Gaseous Hydrocarbons and Produced Water
m) The welding HV5 hardness values shall be lower than the highest hardness
obtained in the welding procedure qualification;
(11) B11, C11, E11, F11, G11 and H11
(12) Operation temperature should be 10oC higher than the gas dew point;
(13) B16, C16, E16, G16, G16P
(14) Requirements for Duplex (22 Cr) and Super Duplex (25 Cr) materials and
equipment for services with H2S:
a) Maximum hardness for Duplex = 310 HV10 / 28 HRc and Super Duplex = 330
HV10/32 HRc
b) PREN of Duplex > 30 ; PREN of Super Duplex > 40
c) Ferrite content (volumetric fraction) for Duplex and Super Duplex shall be between
35% and 65%
(15) B17, E17 (API 5L Gr B)
(16) B19, G19 (A 333 Gr 6)
11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
TITLE:
APPENDIX 5
Corrosiveness of Fluid and Gaseous Hydrocarbons and Produced Water
References:
01 - Corrosion Control of Production Equipment for the Offshore Pampo Field - The
British Petroleum Company Limited - JULY 1979.
02 - How el Paso Designs sour Gas Pipe lines - Pipeline Industry - March 1981.
03 - Sulfide Stress Cracking Resistent Metallic Material for Oil Field Equipments NACE Standard MR0175/ISO 15156.
04 - Aramco Materials System Specifications - Sour Wet Service Line Pipe 01AMSS-16.
05 - NACE TM0177 - Laboratory Testing of Metals for Resistance to Sulfide Stress
Cracking in H2S Environments.
06 - NACE TM0284 - Evaluation of pipeline and pressure vessel steels for
resistance to hydrogen induce cracking.
07 - NORSOK M506 - CO2 corrosion rate calculation model
11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
10
of
TITLE:
APPENDIX 5
Corrosiveness of Fluid and Gaseous Hydrocarbons and Produced Water
Figure 1 Calculation of the pH in function of the H2S and CO2 Partial Pressures,
Temperature and bicarbonate (HCO3 ) concentration in the water (Ref. 3).
11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
11
of
11
TITLE:
APPENDIX 5
Corrosiveness of Fluid and Gaseous Hydrocarbons and Produced Water
Figure 2 Diagram of hardness limits for steel type API 5L proposed for sour service in
function of the pH and the H2S partial pressure (Ref. 3).
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
12
TITLE:
APPENDIX 5
Corrosiveness of Fluid and Gaseous Hydrocarbons and Produced Water
Figure 3: Effect of pressure and water content on the gas dew point.
of
11
N:
TECHNICAL SPECIFICATION
I-ET-3000.00-1200-200-PCI-001
CLIENT:
SHEET:
1 of
1
E&P
PROGRAM:
PIPING MATERIAL - STANDARDIZATION
REA:
ET-200.03
E&P - ENGP
TITLE:
APPENDIX 10
Date
Project
Execution
Verification
Approval
REV. 0
REV. A
REV. B
REV. C
REV. D
Nov/81
DEPRO
M. Assayag
Hernon
Hernon
Mar/91
DEPRO
Jeter
Froes
Hernon
Oct/95
E&P
Fernando
Hernon
Hernon
Apr/00
E&P
Fernando
Hernon
Hernon
Sep/04
E&P
Ney Robson
Fernando
Hernon
REV. E
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORM N-381 REV. F
REV. F
REV. G
REV. H
N:
TECHNICAL SPECIFICATION
CLIENT:
E&P
PROGRAM:
SHEET
of
REA:
ET-200.03
TITLE:
E&P - ENGP
I-ET-3000.00-1200-200-PCI-001
APPENDIX 11
Index
1 - Objective
2 - Service Scope
3 - Project Conditions
4 - Anode Specification
5 - Installation and Attachment of Anodes
6 - Reference Electrode
7 - Storage
8 - Installing the Anodes and Reference Electrodes
Date
Project
Execution
Verification
Approval
REV. 0
REV. A
REV. B
REV. C
REV. D
Dec/78
DEPRO
M. Assayag
Hernon
Hernon
Mar/91
DEPRO
Jeter
Froes
Hernon
Oct/95
E&P
Fernando
Hernon
Hernon
Apr/00
E&P
Fernando
Hernon
Hernon
Sep/04
E&P
Ney Robson
Fernando
Hernon
REV. E
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORM N-381 REV. F
REV. F
REV. G
REV. H
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
2
REV.
of
D
5
TITLE:
APPENDIX 11
Specifications for Utilization Sacrificial Anodes in Piping
1. Objective
This specification covers the requirements necessary for applying sacrificial
anodes for the purpose of protecting the inside surface of piping, permanently
full of sea water, which is internally coated with epoxy, and has a nominal
diameter of 6 or greater. It aims to provide guidelines for applying the anodes
during the phases which entail performance of the execution piping drawings,
during the selection, purchase and assembly of the anodes.
Any omissions in this this specification can be resolved by contacting the anode
manufacturers, providing approval has been granted by the Petrobras
Inspection.
2. Service Scope
The purchase, storage and assembly of the sacrificial anodes should be
performed by the companies responsible for assembling the modules and decks.
They will be purchased according to the specifications indicated in the
requirements or materials list. Any deviation from the anode specification in the
suppliers' proposals is subject to PETROBRAS approval. The anodes should be
purchased from suppliers qualified by PETROBRAS.
The anodes should be installed according to the instructions set out in this is
specification.
Due to the fact the anode mass is sized empirically, the system's performance
should be evaluated by the assembler and/or manufacturer of the anodes
following their assembly, at the criteria of the PETROBRAS Inspection.
3. Project Conditions
The anode mass has been calculated using the applicable calculation criteria,
and the anode data is in accordance with the PETROBRAS specification, see
item 4.
The anodes should be distributed and arranged in order to achieve maximum
efficiency of the system as a whole.
The anodes have a predicted useful life of 10 (ten) years.
The anodes have an estimated efficiency of 20%.
The anodes should be located in the internal part of all the straight pipe sections.
These anodes will be selected for all the flanged connections.
The short sections or sections which obstruct free passage, will not contain
anodes.
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
3
REV.
of
D
5
TITLE:
APPENDIX 11
Specifications for Utilization Sacrificial Anodes in Piping
Care should be taken during the installation not to hinder the operation of the
valves and other piping elements.
4. Anode Specifications
Continuous sacrificial anodes will be used, which should comply with the following
recommended by PETROBRAS.
- Aluminum alloy anodes ACS Type 0.4m
- Aluminum alloy anodes ACS Type 1.4m.
- The anodes will be 25mm in diameter, applicable to 6" to 24" piping respectively.
- The anodes will be supplied in 9-meter bars.
- Use of anodes is not required in the connection joints.
- Examples: Tee curves, flanged curves, flanges with reductions, etc.
5. Installation and fixing of anodes
The installation and fixing of anodes on the SPOOLS shall be carried out as the
diagram below:
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
4
REV.
of
D
5
TITLE:
APPENDIX 11
Specifications for Utilization Sacrificial Anodes in Piping
ANODE
ACS 0,4m
ACS 1,4m
ELECTRODE
OUTSIDE
DIAMETER
12,5
25
RING DIMENSIONS
OUT. 0(mm)
22,5
40
Int. 0 (mm)
13,5
26
Thickness (mm)
10
10
6. Reference Electrode
To evaluate the performance of the cathodic protection system, a zinc reference
electrode, of 3/8"diameter and 150mm length, will be installed for each fluid
system to be cathodically protected.
7. Storage
The sacrificial anodes should be stored so as to avoid damage, and also to avoid
contamination by chemical products, oil, grease etc.
Other storage precautions for the cathodes should be taken together with the
suppliers, in accordance with PETROBRAS standard N-1729.
8. Installing the Anodes and Reference Electrodes
During installation in the piping, the anodes and reference electrodes should be
completely free of grease, oil or other product which reduces the efficiency
thereof.
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
5
REV.
of
D
5
TITLE:
APPENDIX 11
Specifications for Utilization Sacrificial Anodes in Piping
Welding the anodes and reference electrodes in the piping should be performed
with the same level of quality applicable to the piping it self.
The anodes and reference electrodes should only be welded to the piping when
they are ready to be adopted.
Following the welding of the anodes and reference electrodes, the parts of the
epoxy paint which have been affected by the heat should be re-painted.
Care should be taken not to cover any part of the anode surfaces with paint
splashes or any other dielectric element, which will reduce the efficiency thereof.
N:
TECHNICAL SPECIFICATION
I-ET-3000.00-1200-200-PCI-001
CLIENT:
SHEET:
1 of
9
E&P
PROGRAM:
PIPING MATERIAL - STANDARDIZATION
REA:
ET-200.03
E&P - ENGP
TITLE:
APPENDIX 12
Branch Connections Tables
Especification
Type
A4 - A8
B3 - B4 - B5 - B6 - B9 - B10 - B11 - B12 - B14
C3 - C4 - C5 - C6 - C9 - C10 - C12 - C14
E3 - E4 - E5 - E6 - E6R - E9 - E10 - E10R - E14
F3 - F4 - F5 - F6 - F6R - F10 - F10R - F14
G3 - G4 - G5 - G6 - G6R - G10 - G10R - G11 - G12 G14
H3 - H5 - H10
B7 - B7R
II
B20 - B21
III
IV
B25
C8 - E8
VI
VII
B15
VIII
Date
Project
Execution
Verification
Approval
Original
REV. D
REV. E
REV. F
REV. G
REV. H
REV. J
REV. K
REV. L
Nov/81
DEPRO
M.Assayag
Hernon
Hernon
Oct/95
E&P
Fernando
Hernon
Hernon
Sep/04
E&P
Gerson
Fernando
Hernon
Nov/05
E&P
Gerson
Fernando
Joper
Dec/05
E&P
Gerson
Fernando
Joper
Jan/06
E&P
Gerson
Fernando
Joper
Mar/06
E&P
Gerson
Fernando
Joper
May/06
E&P
Gerson
Fernando
Joper
Feb/07
E&P
Gerson
Fernando
Joper
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
2
TITLE:
APPENDIX 12
Branch Connections Tables
Type I
REV.
of
L
9
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
3
REV.
TITLE:
APPENDIX 12
Branch Connections Tables
Type II
of
L
9
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
4
REV.
of
TITLE:
APPENDIX 12
Branch Connections Tables
Type III
L
9
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
5
REV.
of
L
9
TITLE:
APPENDIX 12
Branch Connections Tables
Type IV
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
6
TITLE:
APPENDIX 12
Branch Connections Tables
Type V
REV.
of
L
9
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
7
REV.
of
L
9
TITLE:
APPENDIX 12
Branch Connections Tables
Type VI
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
8
REV.
of
L
9
TITLE:
APPENDIX 12
Branch Connections Tables
Type VII
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
9
TITLE:
APPENDIX 12
Branch Connections Tables
Type VIII
REV.
of
L
9
N:
TECHNICAL SPECIFICATION
I-ET-3000.00-1200-200-PCI-001
CLIENT:
SHEET:
1 of
2
E&P
PROGRAM:
PIPING MATERIAL - STANDARDIZATION
REA:
ET-200.03
E&P - ENGP
TITLE:
APPENDIX 13
Original
Date
Project
Execution
Verification
Approval
REV. A
REV. B
REV. C
REV. D
REV. E
Set/04
E&P
Ver Fl 2
Hernon
Thomaz
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORME N-381 REV. F
REV. F
REV. G
REV. H
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-002
SHEET:
2
REV.
of
TITLE:
APPENDIX 13
Procedure for Internal Coating of Piping with Polyethylene
2.3 - Shore D Hardness of 48, with tolerance of 5. Tests performed in
accordance with the standard ASTM D2240;
2.4 - Adhesion resistance should be at least 14 Kg/cm. Test performed in
accordance with the standard ASTM D1000 (Method B), with a film of
width 10 mm, tensioning velocity of 20 mm/min, in a 2 diameter pipe
at 23C;
2.5 - Penetration resistance lower than 0.2 mm. Test performed in
accordance with the standard DIN 30670 with an area corresponding
to a diameter of 1.8 mm, weight of 2.5 kg for 48 hours at 25C;
2.6 - Erosion/abrasion resistance equal to or greater than 6.5 mg of mass
loss per 1000 cycles. Test performed in accordance with the standard
ASTM D1044, with a load of 1 kg and H-22 abrasive wheels;
2.7 - The polyethylene coating should have a minimum thickness of 1.2 mm
and be evenly distributed along the pipe's internal surface;
2.8 - The internal polyethylene coating allows a maximum work flow rate of 5
m/s when the water contains suspended solids, of the coarse sand
type, and 10 m/s when the water does not contain solids;
2.9 - The maximum permitted temperature for the use of the internal
polyethylene coating with water is 70C;
2.10 - When used in systems with seawater treated with sodium
hypochlorite, the maximum tolerated concentration is 10%.
3 - The piping coated internally with polyethylene should satisfy the following
minimum requirements upon delivery:
3.1 - During the final inspection, first perform a visual check that there are no
discontinuities or projections along the entire surface of the pipe coated
with polyethylene, then perform an inspection using a Holiday Detector
with a 10 kV direct current. Any kind of discontinuities/sparks on the
internal surface and/or coated flange faces of the pipe will not be
accepted.
3.2 - The finish of the internal surface of the pipe coated with polyethylene
should be smooth and, the flange face should be sanded with fine
sandpaper until a smooth surface is achieved. The polyethylene coating
should cover the entire contact face used to seal the flanges.
3.3 - The flanged piping coated internally with polyethylene should be
delivered with EPDM rubber joints (Shore A 60 5) between the parts.
during delivery, the flange ends should be protected by fixed wooden
discs.
N:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
1
E&P
PROGRAM:
PIPING MATERIAL - STANDARDIZATION
AREA:
ET-200.03
E&P - ENGP
TITLE:
of
193
APPENDIX 14
Fully Tight Valves (VET) Description
1 PURPOSE
The purpose of this appendix is to list and describe the technical requirements of
approved VETs for use in Oil & Gas Production Facilities. The selection of these
valves shall be in accordance with DR-ENGP-II-p1-1.3.
Objectives of this appendix:
Set the VET tags for each material and pressure class specification;
Set the VET tags in accordance with DR-ENGP-II-p1-1.3, which describes the
VET series, their selection criteria and application scope;
Guide the project using the Table of Codes, item 7 of this appendix;
Define requirements and criteria for tightness acceptance tests;
Provide specific guidelines for the VET inspection;
Provide instructions for VET commissioning;
Define the warranty time.
2 DEFINITION
VETs (Fully Tight Valves) are the ones which require greater tightness guarantee
and lifetime.
VETs shall have specific constructive characteristics due to their installation
requirements. They are installed in pipes carrying flammable and toxic fluids,
important functions (SDV, BDV, ADV, HV and XV), to assure operational safety and
integrity for people and equipments.
VETs are valves with detailed constructive characteristics and high performance,
dispense the bench test during the construction and assembly stage since it is
attested, in the FAT, by PETROBRAS or its factory representant.
Date
Project
Execution
Verification
Approval
Original
REV. C
REV. D
REV. E
REV. F
REV. G
REV. H
REV. J
R.3
Sep/04
E&P
Levy
Fernando
Thomaz
Dec/05
E&P
Milton
Fernando
Joper
Jan/06
E&P
Milton
Fernando
Joper
Mar/06
E&P
Milton
Fernando
Joper
May/06
E&P
Milton
Fernando
Joper
Feb/07
E&P
Milton
Fernando
Joper
Sep/09
E&P
Milton
Fernando
Cludio
Sep/10
E&P
Milton
Fernando
Dlgio
Nov/10
E&P
EISA
IPP
ENGP
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORM N-381 REV. G
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
193
TITLE:
APPENDIX 14
If the bench test is needed during the construction and assembly stage or the unit
operation, the requirements of this document shall be followed.
The specifications and VET TAGs are described in the Table of Codes, item 7 of
this document.
VETs are sub-divided as follows:
3 WARRANTY PERIOD
All Fully Tight Valves shall be designed with mechanical characteristics that
guarantee tightness operation for, at least, 1,5 years under normal operation, without
needing internal parts maintenance.
Their projects shall also consider at least 300 complete cycles (opening and closing,
once every 2 days) without failure occurence, with maintenance only in the external
parts, without affecting their tightness characteristics (tight shutoff").
Any repairs under warranty, costs of material and logistics will be paid by the
manufacturer.
The valve manufacturer shall formalize this warranty directly for PETROBRAS.
4 SEALING TEST AT THE FACTORY
All Fully Tight Valves, independently of diameter, technical characteristics and
pressure limits shall be tested by suppliers at their factories.
Suppliers shall issue testing certificates in full compliance with the datasheets
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
193
TITLE:
APPENDIX 14
MINIMUM REQUIREMENTS FOR TIGHTNESS TEST
All tests to be performed on construction sites shall have their procedures previously
submitted to PETROBRAS approval.
All tests shall be monitored by PETROBRAS inspectors and by the company
contracted to supply the UEP (Stationary Production Unit).
If a failure is detected during visual inspection (mechanical damage, rust, etc.) or on
the line test (leaks, loss of tightness), the respective valve shall be removed, repaired
and resubmitted to the bench test by the manufacturer.
Valves and lines involved in the test shall undergo a preliminary visual inspection to
verify the integrity of the valve pipe and the absence of internal fragments.
The pressure test to be applied on installed valves shall be 10% above the maximum
operating pressure of the service.
For VET SERIES "200" to "600", VET SERIES "300P" or "500P", the minimum
pressure test shall be 600 Kpag (minimum).
5 INSPECTION AND TESTS
- The testing procedures for valves shall be in accordance with the requirements of
ASME B16.34 and all standards referenced in the valves datasheets.
- The tests shall be according to each kind of material, unless another specification
by the customer.
- Non-destructive tests shall be applied as described below:
CAST IRON AND BRASS VALVES:
- Visual 100%
- For body and castle of cast iron and forged valves, ASME class 150 and 300, the
magnetic particle testing is required in 20% of each batch material.
CARBON STEEL VALVES:
- Visual 100%
- For body and castle of forged valves, class 900, 1500 and 2500, the test of
magnetic particles is required in 100% of each batch material.
- For body and castle of casting valves, class 900, 1500 and 2500, the radiographic
examination in critical areas is required in 100% of each batch material.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
193
TITLE:
APPENDIX 14
STAINLESS STEEL VALVES:
- Visual 100%
- For body and castle of forged and casting valves, class 150 and 300, the Liquid
penetrant test is required in 20% of each batch material.
- For body and castle of forged valves, class 900, 1500 and 2500, the Liquid
penetrant test is required in 100% of each batch material.
- For body and castle of casting valves, class 900, 1500 and 2500, the radiographic
examination is required in 100% in critical areas.
STAINLESS STEEL DUPLEX AND SUPER DUPLEX VALVES:
- Visual 100%
- For body and castle of forged and casting valves, class 150 and 300, the Liquid
penetrant test is required in 20% of each batch material.
- For body and castle of forged valves, class 900, 1500 and 2500, the Liquid
penetrant test is required in 100% of each batch material.
- For body and castle of casting valves, class 900, 1500 and 2500, the radiographic
examination is required in 100% in critical areas.
CONSIDERATION
- The Visual examination shall be according to ASME BPV section V.
The acceptance criteria shall be according to MSS SP-55 specification.
- The magnetic particles test shall be according to ASME BPV section V.
The acceptance criteria shall be according to ASME B16.34 specification.
- The visual examination shall be according to ASME BPV section V.
The acceptance criteria shall be according to ASME B16.34 specification.
-
LEAKAGE TEST
Valve tightness tests and valve body hydrostatic test shall be according to ISO
14313 (API 6D) specification, along with the zero leakage criterium for all valves
including metal to metal in accordance with ISO 5208 rate A.
High pressure closing test closing is required for gate valves and globe valves.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
193
TITLE:
APPENDIX 14
High pressure closing test is required for all ball valves.
The valve body hydrostatic test shall be 1.5 times the design pressure. The seat test
shall be 1.1 times the design pressure.
The pneumatic seat test shall be according to the requirements of ISO 14313 (API
6D), along with the zero leakage criterium.
All tests shall be performed before the painting process.
Water used in hydrostatic test shall contain 1% of biodegradable protective agent
and a maximum of 30 ppm chloride, when the test is performed in stainless steel
valves.
The average pH during the test shall be between 6.5 and 8.5.
Soft seat valves shall be actuated at least three times before starting the hydrostatic
test.
Valves with the gearbox shall be tested assembled.
Petrobras or a representant shall carry out random inspection on parts and
manufacturing processes at supply factories.
Petrobras or a representant shall carry out inspection of all valves described in this
technical specification at supply factories.
Petrobras or a representant shall carry out a complete verification of the
manufacturing, transporting, receiving and packaging process of the valve to ensure the
maintenance of the manufacturer acceptance standards.
Petrobras or a representant shall carry out a monitoring in the complete process of
valves installation in the shipyards to ensure that the valves will not be damaged during
assembly.
6 ITEM COMMISSIONING
All Fully Tight Valves (VET) shall be part of the commissioning program, having
the same treatment as items of this document.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
193
TITLE:
APPENDIX 14
7 Table of code
Spec
VET-002
(6" 24")
VET-060
(1/2" 1 1/2")
VET-100
(2 24)
VET-401
(1 - 18)
VET-821
(6" 24")
VET-822
(26" 40")
VET-823
(6" 24")
VET-824
(26" 40")
VET-825
(6" 24")
VET-826
(26" 40")
VET-1302
(10" - 12")
VET-050
(2" 4")
VET-051
(6" 24")
VET-076
(1/2" 1 1/2")
VET-200
(10" - 24")
VET-902A
(2" 4")
VET-902B
(6" 24")
VET-003
(2" 4")
VET-004
(6" 24")
VET-005
(26" 36")
VET-061
(1/2" 1 1/2")
VET-103
(2 24)
VET-208
(26" - 36")
VET-209
(26" - 36")
VET-403
(2 - 18)
VET-1324
(10" - 14")
VET-202
(12" 24")
VET-203
(26" - 36")
VET-605
(2" 8")
VET-606
(10" 24")
VET-607
(26" 36")
VET-851
(6" 24")
VET-852
(26" 40")
VET-853
(6" 24")
VET-854
(26" 40")
B7R
VET-202
(12" 24")
VET-203
(26" - 36")
VET-600
(2" 10")
VET-601
(12" 24")
VET-602
(26" 36")
VET-617
(26" 36")
B9
VET-006
(2" 4")
VET-007
(6" 24")
VET-008
(26" 36")
VET-062
(1/2" 1 1/2")
VET-105
(2 24)
VET-405
(1 - 18 (20
and 24)*)
VET-902A
(2" 4")
VET-902B
(6" 24")
VET-1325
(10" - 14")
VET-006
(2" 4")
VET-007
(6" 24")
VET-008
(26" 36")
VET-062
(1/2" 1 1/2")
VET-105
(2 24)
VET-200
(10" - 24")
VET-201
(26" - 36")
VET-405
(1 - 18 (20
and 24)*)
VET-505
(5 - 24)
VET-600
(2" 10")
VET-601
(12" 24")
VET-602
(26" 36")
VET-617
(26" 36")
VET-801
(6" 24")
VET-802
(26" 40")
VET-803
(6" 24")
VET-804
(26" 40")
VET-805
(6" 24")
VET-806
(26" 40")
VET-902A
(2" 4")
VET-902B
(6" 24")
VET-1325
(10" - 14")
B3
B4
VET-1326
(10" - 14")
B6
B7
B10
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
193
TITLE:
APPENDIX 14
Spec
VET-140
(2 24)
VET-216
(10" - 24")
VET-443
(1 - 18 (20
and 24)*)
VET-083
(26" 36")
VET-088
(1/2" 1 1/2")
VET-138
(2 24)
VET-213
(10" - 24")
VET-091
(6" 24")
VET-098
(1/2" 1 1/2")
VET-204
(10" - 24")
VET-205
(26" - 36")
VET-610
(2" 10")
VET-611
(12" 24")
VET-612
(26" 44")
VET-615
(2" 8")
VET-616
(10" 24")
VET-855
(6" 24")
VET-856
(26" 40")
VET-105
(2 24)
VET-202
(12" 24")
VET-203
(26" - 36")
VET-615
(2" 8")
FLG
VET-801
(6" 24")
FLG
VET-802
(26" 40")
WAFER
VET-803
(6" 24")
WAFER
VET-804
(26" 40")
LUG
VET-805
(6" 24")
LUG
VET-806
(26" 40")
VET-043
(1/2" 1 1/2")
VET-043A
(2" 4")
VET-043B
(6" 24")
VET-827
(6" 24")
VET-828
(26" 40")
VET-829
(6" 24")
VET-830
(26" 40")
VET-831
(6" 24")
VET-832
(26" 40")
VET-1313
(10" - 14")
B17
VET-006
(2" 4")
VET-007
(6" 24")
VET-062
(1/2" 1 1/2")
VET-902A
(2" 4")
VET-902B
(6" 24")
B19
VET-003
(2" 4")
VET-004
(6" 24")
VET-005
(26" 36")
VET-061
(1/2" 1 1/2")
VET-1324
(10" - 14")
B22
VET-204
(10" - 24")
VET-205
(26" - 36")
150 psig
VET-610
(2" 10")
150 psig
VET-611
(12" 24")
150 psig
VET-612
(26" 44")
250 psig
VET-616
(10" 24")
VET-855
(6" 24")
VET-856
(26" 40")
VET-1505
(4" - 10")
VET-1506
(12" - 48")
VET-615
(2" 8")
VET-616
(10" 24")
VET-855
(6" 24")
VET-856
(26" 40")
VET-1505
(4" - 10")
B11
B12
B14
B15
B16
B23
VET-092
(1" 1 1/2")
VET-093
(2" 4")
VET-515
(6 - 24)
VET-901
(1" 1 1/2")
VET-081
(2" 4")
VET-082
(6" 24")
VET-407
(1 - 18 (20
and 24)*)
VET-507
(6 - 24)
VET-090
(2" 4")
250 psig
VET-615
(2" 8")
VET-1506
(12" - 48")
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
TITLE:
APPENDIX 14
Spec
C3
VET-054
(2" 4")
VET-055
(6" 18")
VET-060
(1/2" 1 1/2")
VET-110
(2 18)
VET-409
(2 - 18)
C4
VET-058
(2" 4")
VET-059
(6" 24")
VET-076
(1/2" 1 1/2")
VET-206
(10" - 24")
VET-1330
(10" - 14")
C6
VET-009
(2" 4")
VET-010
(6" 24")
VET-061
(1/2" 1 1/2")
VET-113
(2 24)
VET-210
(10" - 24")
VET-411
(2 - 20)
VET-713
(2 24)
VET-1328
(10" - 14")
C9
VET-011
(2" 4")
VET-012
(6" 24")
VET-062
(1/2" 1 1/2")
VET-115
(2 24)
VET-413
(2 - 20)
VET-1329
(10" - 14")
C10
VET-011
(2" 4")
VET-012
(6" 24")
VET-062
(1/2" 1 1/2")
VET-115
(2 24)
VET-206
(10" - 24")
VET-413
(2 - 20)
VET-1304
(10" - 14")
VET-1329
(10" - 14")
C11
VET-056
(1" 1 1/2")
VET-069A
(2" 4")
VET-069B
(6" 24")
VET-904
(1" 1 1/2")
VET-905A
(2" 4")
VET-905B
(6" 24")
C12
VET-077
(2" 4")
VET-078
(6" 24")
VET-088
(1/2" 1 1/2")
VET-415
(2 - 20)
VET-509
(5 - 24)
VET-714
(2 24)
C14
VET-052
(1/2" 1 1/2")
VET-052A
(2" 4")
VET-052B
(6" 24")
C16
VET-048
(1/2" 1 1/2")
VET-048A
(2" 4")
VET-048B
(6" 24")
VET-715
(2 24)
VET-833
(6" 24")
VET-834
(26" 40")
VET-835
(6" 24")
VET-836
(26" 40")
VET-837
(6" 24")
VET-838
(26" 40")
VET-1315
(10" - 14")
C30
VET-056
(1" 1 1/2")
VET-069A
(2" 4")
VET-069B
(6" 24")
VET-905A
(2" 4")
VET-905B
(6" 24")
E3
VET-015
(2" 4")
VET-016
(6" 24")
VET-060
(1/2" 1 1/2")
VET-120
(2 12)
VET-300
(2" 4")
VET-417
(2 - 12)
VET-717
(2 16)
VET-1001
(3" 6")
VET-1306
(10" - 14")
VET-1400
(1/2" 2")
VET-301
(6" 8")
193
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
TITLE:
APPENDIX 14
Spec
E4
VET-303
(2" 4")
VET-304
(6" 8")
VET-718
(2 16)
VET-1334
(10" - 14")
E6
VET-017
(2" 4")
VET-018
(6" 24")
VET-061
(1/2" 1 1/2")
VET-123
(2 24)
VET-306
(2" 5")
VET-419
(2 - 20)
VET-719
(2 16)
VET-1012
(3" 6")
VET-1332
(10" - 14")
VET-1401
(1/2" 2")
VET-017
(2" 4")
VET-018
(6" 24")
VET-061
(1/2" 1 1/2")
VET-123
(2 24)
VET-306
(2" 5")
VET-419
(2 - 20)
VET-719
(2 16)
VET-1012
(3" 6")
VET-1332
(10" - 14")
VET-1401
(1/2" 2")
VET-013
(2" 4")
VET-014
(6" 24")
VET-062
(1/2" 1 1/2")
VET-125
(2 24)
VET-303
(2" 4")
VET-304
(6" 8")
VET-423
(2 - 20)
VET-718
(2 16)
VET-918A
(2" 4")
VET-918B
(6" 24")
VET-1333
(10" - 14")
VET-1433
(1/2" 2")
VET-013
(2" 4")
VET-014
(6" 24")
VET-062
(1/2" 1 1/2")
VET-125
(2 24)
VET-303
(2" 4")
VET-304
(6" 8")
VET-423
(2 - 20)
VET-510
(5- 24)
VET-511
(26- 34)
VET-718
(2 16)
VET-918A
(2" 4")
VET-918B
(6" 24")
VET-1006
(3" 6")
VET-1333P
(10" - 14")
VET-1333
(10" - 14")
VET-1433
(1/2" 2")
VET-1500
(12" - 24")
E6R
E9
E10
E10P
VET-1006P
(3" 6")
E11
VET-1402
(1/2" 2")
E14
VET-013
(2" 4")
VET-014
(6" 24")
VET-053
(1/2" 1 1/2")
VET-1403
(1/2" 2")
E16
VET-039
(1/2" 1 1/2")
VET-039A
(2" 4")
VET-039B
(6" 24")
VET-720
(2 16)
VET-1430
(1/2" 2")
VET-1004
(2" 8")
VET-307
(6" 8")
VET-307
(6" 8")
VET-1317
(10" - 12")
193
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
10
of
TITLE:
APPENDIX 14
Spec
VET-014
(6" 24")
VET-1333
(10" - 14")
VET-1433
(1/2" 2")
E30
VET-026
(2" 4")
F3
E17
F6
VET-062
(1/2" 1 1/2")
VET-221
(10" - 24")
VET-038
(6" 24")
VET-079
(1/2" 1 1/2")
VET-1402
(1/2" 2")
VET-023
(3" 4")
VET-024
(6" 10")
VET-027
(2" 3")
VET-314
(6" 8")
VET-319
(2" 4")
VET-921B
(6" 10")
VET-718
(2 16)
VET-1006
(3" 6")
VET-070
(1/2" 1 1/2")
VET-130
(2 10)
VET-313
(3" 4")
VET-427
(3 - 10)
VET-435
(2 - 12)
VET-721
(2 14)
VET-921A
(3" 4")
VET-924
(1" 1 1/2")
VET-925A
(2")
VET-1002
(2" 8")
VET-1309
(10" - 12")
VET-1405
(1/2" 2")
VET-029
(3" 4")
VET-030
(6" 10")
VET-033
(2")
VET-072
(1/2" 1 1/2")
VET-133
(2 10)
VET-317
(3" 4")
VET-318
(6" 8")
VET-321
(2" 4")
VET-429
(3 - 10)
VET-722
(2 14)
VET-1013
(2" 8")
VET-1337
(10" - 12")
VET-029
(3" 4")
VET-030
(6" 10")
VET-033
(2")
VET-072
(1/2" 1 1/2")
VET-133
(2 10)
VET-317
(3" 4")
VET-318
(6" 8")
VET-321
(2" 4")
VET-429
(3 - 10)
VET-722
(2 14)
VET-1013
(2" 8")
VET-1337
(10" - 12")
VET-019
(3" 4")
VET-020
(6" 18")
VET-021
(2")
VET-068
(1/2" 1 1/2")
VET-135
(2 10)
VET-311
(3" 4")
VET-312
(6" 8")
VET-315
(2" 5")
VET-431
(3 - 18)
VET-439
(1 - 12)
VET-500
(5 - 18)
VET-723
(2 14)
VET-1008
(2" 8")
VET-1340
(10" - 14")
VET-1407
(1/2" 2")
VET-1406
(1/2" 2")
F6R
VET-1406
(1/2" 2")
F10
193
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
11
of
TITLE:
APPENDIX 14
Spec
VET-020
(6" 18")
VET-021
(2")
VET-068
(1/2" 1 1/2")
VET-135
(2 10)
VET-311
(3" 4")
VET-312
(6" 8")
VET-315
(2" 5")
VET-431
(3 - 18)
VET-439
(1 - 12)
VET-500
(5 - 18)
VET-723
(2 14)
VET-1008
(2" 8")
VET-1340
(10" - 14")
VET-1407
(1/2" 2")
F10P
VET-1008P
(2" 8")
VET-1340
(10" - 14")
F11
VET-1408
(1/2" 2")
F14
VET-019
(3" 4")
VET-020
(6" 18")
VET-021
(2")
VET-099
(1/2" 1 1/2")
VET-1409
(1/2" 2")
G3
VET-027
(2" 3")
VET-028
(4" 24")
VET-070
(1/2" 1 1/2")
VET-319
(2" 4")
VET-320
(6" 8")
VET-435
(2 - 12)
VET-725
(2 12)
VET-1003
(2" 8")
VET-1311
(10" - 14")
VET-1405
(1/2" 2")
VET-033
(2" 3")
VET-034
(4" 10")
VET-072
(1/2" 1 1/2")
VET-322
(6" 8")
VET-321
(2" 4")
VET-437
(2 - 10)
VET-726
(2 12)
VET-1014
(2" 8")
VET-1345
(10" - 12")
VET-1406
(1/2" 2")
VET-033
(2" 3")
VET-034
(4" 10")
VET-072
(1/2" 1 1/2")
VET-322
(6" 8")
VET-321
(2" 4")
VET-437
(2 - 10)
VET-726
(2 12)
VET-1014
(2" 8")
VET-1345
(10" - 12")
VET-1406
(1/2" 2")
VET-021
(2" 3")
VET-022
(4" 24")
VET-068
(1/2" 1 1/2")
VET-212
(10" - 24")
VET-315
(2" 5")
VET-316
(6" 8")
VET-439
(1 - 12)
VET-503
(2 - 24)
VET-732
(2 12)
VET-940A
(2" 4")
VET-940B
(6" 24")
VET-1010
(2" 8")
VET-1342
(10" - 14")
VET-1407
(1/2" 2")
VET-1502
(4" - 10")
F10R
G6
G6R
G10
193
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
12
of
193
TITLE:
APPENDIX 14
Spec
VET-068
(1/2" 1 1/2")
VET-315P
(2" 5")
VET-316P
(6" 8")
VET-940BP
(6" 24")
VET-1010P
(2" 8")
VET-1342P
(10" - 14")
VET-1407
(1/2" 2")
VET-021
(2" 3")
VET-022
(4" 24")
VET-068
(1/2" 1 1/2")
VET-503
(2 - 24)
VET-732
(2 12)
VET-095
(1" 1 1/2")
VET-503P
(2 - 12)
VET-940AP
(2" 4")
VET-315
(2" 5")
VET-316
(6" 8")
VET-439
(1 - 12)
VET-940A
(2" 4")
VET-940B
(6" 24")
VET-1010
(2" 8")
VET-1342
(10" - 14")
VET-096
(2" 3")
VET-097
(4" 24")
VET-097
(4" 24")
VET-218
(10" - 24")
VET-328
(2" 4")
VET-329
(6" 8")
VET-445
(1 - 12)
VET-517
(2 - 24)
VET-1408
(1/2" 2")
VET-086
(2" 3")
VET-087
(4" 24")
VET-089
(1/2" 1 1/2")
VET-214
(10" - 24")
VET-441
(1 - 12)
VET-513
(2 - 24)
VET-728
(2 12)
VET-1011
(2" 8")
VET-1410
(1/2" 2")
G12P
VET-327P
(6" 24")
VET-1410
(1/2" 2")
G14
VET-021
(2" 3")
VET-022
(4" 24")
VET-099
(1/2" 1 1/2")
VET-315
(2" 5")
VET-316
(6" 8")
VET-439
(1 - 12)
VET-031
(1/2" 1 1/2")
VET-031A
(2" 3")
VET-031B
(4" 24")
VET-222
(10" - 24")
VET-729
(2 12)
VET-929A
(2" 4")
VET-929B
(6" 24")
VET-1005
(2" 8")
VET-1322
(10" - 14")
VET-1432
(1/2" 2")
VET-031
(1/2" 1 1/2")
VET-031A
(2" 3")
VET-031BP
(4" 24")
VET-929AP
(2" 4")
VET-929BP
(6" 24")
VET-1005P
(2" 8")
VET-1322P
(10" - 12")
VET-1432
(1/2" 2")
G10P
G10R
VET-1407
(1/2" 2")
G11
G12
VET-1409
(1/2" 2")
G16
G16P
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
13
of
193
TITLE:
APPENDIX 14
Spec
G19
VET-033
(2" 3")
VET-034
(4" 10")
VET-072
(1/2" 1 1/2")
VET-1014
(2" 8")
VET-1345
(10" - 12")
VET-1412
(1/2" 2")
H3
VET-046
(2" 3")
VET-047
(4" 10")
VET-075
(1" 1 1/2")
VET-730
(2 6)
VET-1015
(2" 8")
VET-1413
(1/2" 2")
H10
VET-044
(2" 3")
VET-045
(4" 12")
VET-074
(1" 1 1/2")
VET-325
(2" 8")
VET-731
(2 6)
VET-931A
(2" 3")
VET-931B
(4" 12")
VET-1016
(2" 8")
VET-1343
(10" - 12")
VET-1414
(1/2" 2")
VET-1503
(4" - 10")
H11
VET-035
(1" 1 1/2")
VET-036
(2" 3")
VET-037
(4" 12")
VET-1415
(1/2" 2")
H14
VET-025
(1" 1 1/2")
VET-044
(2" 3")
VET-045
(4" 12")
VET-1343
(10" - 12")
VET-1351
(10" - 12")
VET-1416
(1/2" 2")
H30
VET-035
(1" 1 1/2")
VET-037C
(14" 20")
VET-036
(2" 3")
VET-037
(4" 12")
VET-906
(1" 1 1/2")
VET-907A
(2" 3")
VET-907B
(4" 12")
VET-907C
(14" - 20")
VET-1018
(2" 8")
VET-1415
(1/2" 2")
VET-1700
(6" - 12")
VET-1701
(14" - 20")
VET-045CP
(24")
VET-044
(2" 3")
VET-045P
(4" 12")
VET-074
(1" 1 1/2")
VET-931A
(2" 3")
VET-931BP
(4" 12")
VET-1016P
(2" 8")
VET-1414
(1/2" 2")
VET-035
(1" 1 1/2")
VET-037CP
(14" 20")
VET-036
(2" 3")
VET-037P
(4" 12")
VET-906
(1" 1 1/2")
VET-907BP
(4" 12")
VET-907CP
(14" - 20")
VET-1415
(1/2" 2")
J31
VET-1504
(4" - 8")
VET-1600
(1" 1 1/2")
J31P
VET-1601P
(4" 8")
H10P
H30P
VET-1601
(2" 14")
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
14
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B3
VET-001
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 351 Grade CF8M
split body
combined drain and vent
trunnion
full bore
AISI 316
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
B3
VET-002
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 351 Grade CF8M
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 316
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
N/A
PTFE + Elgiloy
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
15
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test
complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B6 B19
VET-003
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 352 Grade LCB
split body
combined drain and vent
trunnion
full bore
AISI 304
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
B6 B19
VET-004
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 352 Grade LCB
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 304
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
N/A
PTFE + Elgiloy
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
16
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B6 B19
VET-005
Ball valve - double piston effect (DPE)
26" 36"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 352 Grade LCB
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 304
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
B9 B10 B17
VET-006
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 216 Grade WCB (3)
split body
combined drain and vent
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
Viton GLT
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
17
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B9 B10 B17
VET-007
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
Viton GLT
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
B9 B10
VET-008
Ball valve - double piston effect (DPE)
26" 36"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
Viton GLT
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
18
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
C6
VET-009
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 352 Grade LCB
split body
combined drain and vent
trunnion
full bore
AISI 304
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
C6
VET-010
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 352 Grade LCB
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 304
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
N/A
PTFE + Elgiloy
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
19
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
C9 C10
VET-011
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 216 Grade WCB (3)
split body
combined drain and vent
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
Viton GLT
N/A
A 182 Grade F 316
C9 C10
VET-012
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
Viton GLT
N/A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
20
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
21
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
E3
VET-015
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
600
A 351 Grade CF8M
split body
combined drain and vent
trunnion
full bore
AISI 316
Inconel X750
Devlon V
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
E3
VET-016
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
600
A 351 Grade CF8M
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 316
Inconel X750
Devlon V
-46C to 150C
N/A
PTFE + Elgiloy
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
22
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
E6 E6R
VET-017
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
600
A 352 Grade LCB
split body
combined drain and vent
trunnion
full bore
AISI 304
Inconel X750
Devlon V
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
E6 E6R
VET-018
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
600
A 352 Grade LCB
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 304
Inconel X750
Devlon V
-46C to 150C
N/A
PTFE + Elgiloy
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
23
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Marking:
General requirement:
Bolt/nut:
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
Test complement
according ISO 14313
(API 6D):
Test:
Notes:
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
24
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
25
of
193
TITLE:
APPENDIX 14
Espec
Tag
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
full bore
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
AISI 410
Inconel X750
PEEK
-29C to 150C
Viton GLT
N/A
Type:
NPS:
Standard:
Certificate:
End/finishing:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G10P
VET-022P
Ball valve - double piston effect (DPE)
piggable
4" 12"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
piggable - internal diameter (ID) valve
shall be
defined by Project Engineer
AISI 410
Inconel X750
PEEK
-29C to 150C
Viton GLT
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
26
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
F3
VET-023
Ball valve
3" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
900
A 351 Grade CF8M
split body
combined drain and vent
trunnion
full bore
AISI 316
Inconel X750
Devlon V
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
F3
VET-024
Ball valve - double piston effect (DPE)
6" 10"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
900
A 351 Grade CF8M
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 316
Inconel X750
Devlon V
-46C to 150C
N/A
PTFE + Elgiloy
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
27
of
193
TITLE:
APPENDIX 14
Espec
Tag
H14
VET-025
Class:
Ball valve
1/2" 1 1/2"
ASME B16.34 (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
Body material:
A 105
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
split body
combined drain and vent
trunnion
full bore
AISI 410
Inconel X750
PEEK
-29C to 150C
PTFE reinforced with 25% of carbon
N/A
Type:
NPS:
Standard:
Certificate:
End/finishing:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
E30
VET-026
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
600
A 216 Grade WCB + Inconel 625
(UNS N06625)
split body
combined drain and vent
trunnion
full bore
AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
Devlon V
-29C to 150C
Viton GLT
N/A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
28
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
F3 G3
VET-027
Ball valve
2" 3"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 351 Grade CF8M
split body
combined drain and vent
trunnion
full bore
AISI 316
Inconel X750
PEEK
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
G3
VET-028
Ball valve - double piston effect (DPE)
4" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 351 Grade CF8M
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 316
Inconel X750
PEEK
-46C to 150C
N/A
PTFE + Elgiloy
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
29
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
F6 F6R
VET-029
Ball valve
3" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
900
A 352 Grade LCB
split body
combined drain and vent
trunnion
full bore
AISI 304
Inconel X750
Devlon V
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
F6 F6R
VET-030
Ball valve - double piston effect (DPE)
6" 10"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
900
A 352 Grade LCB
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 304
Inconel X750
Devlon V
-46C to 150C
N/A
PTFE + Elgiloy
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
30
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
G16 G16P
VET-031
Ball valve
1/2" 1 1/2"
ASME B16.34 (1)
fire tested ISO 10497 (2); monogram
API
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
1500
A 182 Grade F 51 (UNS S31803)
split body
combined drain and vent
trunnion
full bore
A 995 Grade 4A (UNS J92205)
Inconel X750
PEEK
-46C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
Marking:
General requirement:
Bolt/nut:
Test:
Test complement
according ISO 14313
(API 6D):
Notes:
G16 G16P
VET-031A
Ball valve
2" 3"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 995 Grade 4A (UNS J92205)
split body
combined drain and vent
trunnion
full bore
A 995 Grade 4A (UNS J92205)
Inconel X750
PEEK
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
31
of
193
TITLE:
APPENDIX 14
Espec
Tag
G16
VET-031B
Type:
NPS:
Standard:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
4" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 995 Grade 4A (UNS J92205)
split body
vent / drain plug in the cavity
trunnion
Bore type:
full bore
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Certificate:
End/finishing:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G16P
VET-031BP
Ball valve - double piston effect (DPE)
piggable
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 995 Grade 4A (UNS J92205)
split body
vent / drain plug in the cavity
trunnion
piggable - internal diameter (ID) valve
shall be
defined by Project Engineer
A 995 Grade 4A (UNS J92205)
Inconel X750
PEEK
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
32
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
F6 F6R
VET-033
Ball valve
2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 352 Grade LCB
split body
combined drain and vent
trunnion
full bore
AISI 304
Inconel X750
PEEK
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
G6 G6R G19
VET-033
Ball valve
2" 3"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 352 Grade LCB
split body
combined drain and vent
trunnion
full bore
AISI 304
Inconel X750
PEEK
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
33
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G6 G6R G19
VET-034
Ball valve - double piston effect (DPE)
4" 10"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 352 Grade LCB
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 304
Inconel X750
PEEK
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
34
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
H30
VET-037C
H30P
VET-037CP
Ball valve - double piston effect (DPE)
Ball valve - double piston effect (DPE)
piggable
14" 20"
14" 20"
ISO 14313 (API 6D) (1)
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
fire tested ISO 10497 (2); monogram
API
API
compact flange NORSOK L-005; seal
compact flange NORSOK L-005; seal
type IX (MSJ)
type IX (MSJ)
2500
2500
A 216 Grade WCB + Inconel 625
A 216 Grade WCB + Inconel 625
(UNS N06625)
(UNS N06625)
split body
split body
vent / drain plug in the cavity
vent / drain plug in the cavity
trunnion
trunnion
piggable - internal diameter (ID) valve
full bore
shall be
defined by Project Engineer
AISI 410 + Inconel 625 (UNS N06625) AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
Inconel X750
PEEK
PEEK
-29C to 150C
-29C to 150C
N/A
N/A
PTFE + Elgiloy
PTFE + Elgiloy
A 182 Grade F 316
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
35
of
193
TITLE:
APPENDIX 14
Espec
Tag
Class:
H10P
VET-045CP
Ball valve - double piston effect (DPE)
24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
compact flange NORSOK L-005; seal
type IX (MSJ)
2500
Body material:
Body type:
Vent/drain:
Ball mounting:
split body
vent / drain plug in the cavity
trunnion
piggable - internal diameter (ID) valve
shall be
defined by Project Engineer
AISI 410
Inconel X750
PEEK
-29C to 150C
N/A
PTFE + Elgiloy
Type:
NPS:
Standard:
Certificate:
End/finishing:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
full bore
AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
PEEK
-29C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
36
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
H11 H30
VET-037
Ball valve - double piston effect (DPE)
4" 12"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 216 Grade WCB + Inconel 625
(UNS N06625)
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
PEEK
-29C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
E30
VET-038
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
600
A 216 Grade WCB + Inconel 625
(UNS N06625)
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
Devlon V
-29C to 150C
Viton GLT
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
37
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
E16
VET-039
Ball valve
1/2" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
800
A 182 Grade F 51 (UNS S31803)
split body
combined drain and vent
floating
full bore
A 182 Grade F 51 (UNS S31803)
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
Marking:
General requirement:
Bolt/nut:
Test:
Test complement
according ISO 14313
(API 6D):
Notes:
E16
VET-039A
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
600
A 995 Grade 4A (UNS J92205)
split body
combined drain and vent
trunnion
full bore
A 995 Grade 4A (UNS J92205)
Inconel X750
Devlon V
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
38
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
E16
VET-039B
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
600
A 995 Grade 4A (UNS J92205)
split body
vent / drain plug in the cavity
trunnion
full bore
A 995 Grade 4A (UNS J92205)
Inconel X750
Devlon V
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
B16
VET-043
Ball valve
1/2" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
socket weld with niple SCH 40S
800
A 182 Grade F 51 (UNS S31803)
split body
combined drain and vent
floating
full bore
A 182 Grade F 51 (UNS S31803)
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D) (7)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing;
according MSS SP-25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
39
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B16
VET-043A
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 995 Grade 4A (UNS J92205)
split body
combined drain and vent
trunnion
full bore
A 995 Grade 4A (UNS J92205)
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
B16
VET-043B
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 995 Grade 4A (UNS J92205)
split body
vent / drain plug in the cavity
trunnion
full bore
A 995 Grade 4A (UNS J92205)
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
N/A
PTFE + Elgiloy
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
40
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
H30P
VET-037P
Ball valve - double piston effect (DPE)
piggable
4" 12"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 216 Grade WCB + Inconel 625
(UNS N06625)
split body
vent / drain plug in the cavity
trunnion
piggable - internal diameter (ID) valve
shall be
defined by Project Engineer
AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
PEEK
-29C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
full bore
AISI 410
Inconel X750
PEEK
-29C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
41
of
193
TITLE:
APPENDIX 14
Espec
Tag
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
H10 H14
VET-045
Ball valve - double piston effect (DPE)
4" 12"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
Bore type:
full bore
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
AISI 410
Inconel X750
PEEK
-29C to 150C
N/A
PTFE + Elgiloy
Type:
NPS:
Standard:
Certificate:
End/finishing:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
H10P
VET-045P
Ball valve - double piston effect (DPE)
4" 12"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
piggable - internal diameter (ID) valve
shall be
defined by Project Engineer
AISI 410
Inconel X750
PEEK
-29C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
42
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
H3
VET-046
Ball valve
2" 3"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 351 Grade CF8M
split body
combined drain and vent
trunnion
full bore
AISI 316
Inconel X750
PEEK (6)
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
H3
VET-047
Ball valve - double piston effect (DPE)
4" 10"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 351 Grade CF8M
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 316
Inconel X750
PEEK (6)
-46C to 150C
N/A
PTFE + Elgiloy
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
43
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
C16
VET-048
Ball valve
1/2" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
socket weld with niple SCH 40S
800
A 182 Grade F 51 (UNS S31803)
split body
combined drain and vent
floating
full bore
A 182 Grade F 51 (UNS S31803)
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
Marking:
General requirement:
Bolt/nut:
Test:
Test complement
according ISO 14313
(API 6D):
Notes:
C16
VET-048A
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 995 Grade 4A (UNS J92205)
split body
combined drain and vent
trunnion
full bore
A 995 Grade 4A (UNS J92205)
Inconel X750
PTFE reinforced with 25% of carbon (6)
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
44
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
C16
VET-048B
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 995 Grade 4A (UNS J92205)
split body
vent / drain plug in the cavity
trunnion
full bore
A 995 Grade 4A (UNS J92205)
Inconel X750
PTFE reinforced with 25% of carbon (6)
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
B4
VET-050
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 216 Grade WCB (3)
split body
combined drain and vent
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 210C
Viton GLT
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
45
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B4
VET-051
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 210C
Viton GLT
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
C14
VET-052
Ball valve
1/2" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; flat face (FF)
300
A 105
split body
combined drain and vent
floating
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon (6)
-29C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing;
according MSS SP-25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
46
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
C14
VET-052A
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; flat face (FF)
300
A 216 Grade WCB (3)
split body
combined drain and vent
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
Viton GLT
N/A
A 182 Grade F 316
C14
VET-052B
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; flat face (FF)
300
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
Viton GLT
N/A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
47
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
E14
VET-053
Ball valve
1/2" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
600
A 105
split body
combined drain and vent
floating
full bore
AISI 410
Inconel X750
Devlon V
-29C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
Test complement
according ISO 14313
(API 6D):
C3
VET-054
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 351 Grade CF8M
split body
combined drain and vent
trunnion
full bore
AISI 316
Inconel X750
PTFE reinforced with 25% of carbon (6)
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
48
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
C3
VET-055
Ball valve - double piston effect (DPE)
6" 18"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 351 Grade CF8M
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 316
Inconel X750
PTFE reinforced with 25% of carbon (6)
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
C11 C30
VET-056
Ball valve
1" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 105 + Inconel 625 (UNS N06625)
split body
combined drain and vent
floating
full bore
AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing;
according MSS SP-25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
49
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
C4
VET-058
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 216 Grade WCB (3)
split body
combined drain and vent
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 210C
Viton GLT
N/A
A 182 Grade F 316
C4
VET-059
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 210C
Viton GLT
N/A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
50
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
B3 C3 E3
VET-060
Ball valve
1/2" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
800
A 182 Grade F 316
split body
combined drain and vent
floating
full bore
AISI 316
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
PTFE reinforced with 25% of carbon
N/A
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B6 B19 C6 E6 E6R
VET-061
Ball valve
1/2" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
socket weld with niple
1" - 1 " SCH 80 - B6 B19 C6 E6R
1" - 1 " SCH 160 - E6
800
A 350 Grade LF2 CL 1
split body
combined drain and vent
floating
full bore
AISI 304
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing;
according MSS SP-25
locking device; anti-static device
manufacturer standard
dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
51
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
800
A 105
split body
combined drain and vent
floating
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon (6)
-29C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing;
according MSS SP-25
locking device; anti-static device
manufacturer standard
dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
52
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
C11 C30
VET-069A
C11 C30
VET-069B
Ball valve
Ball valve - double piston effect (DPE)
2" 4"
6" 24"
ISO 14313 (API 6D) (1)
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
fire tested ISO 10497 (2); monogram
API
API
flange ASME B16.5; raised face (RF)
flange ASME B16.5; raised face (RF)
300
300
A 216 Grade WCB + Inconel 625
A 216 Grade WCB + Inconel 625
(UNS N06625)
(UNS N06625)
split body
split body
combined drain and vent
vent / drain plug in the cavity
trunnion
trunnion
full bore
full bore
AISI 410 + Inconel 625 (UNS N06625) AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
Inconel X750
PTFE reinforced with 25% of carbon
PTFE reinforced with 25% of carbon
-29C to 150C
-29C to 150C
Viton GLT
Viton GLT
N/A
N/A
A 182 Grade F 316
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
53
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
F3 G3
VET-070
Ball valve
1/2" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
socket weld with niple
1 SCH 40S - F3
1 " SCH 80S - F3
1" - 1 SCH 160 - G3
1500
A 182 Grade F 316
split body
combined drain and vent
trunnion
full bore
AISI 316
Inconel X750
PEEK
-46C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing;
According MSS SP-25
locking device; anti-static device
manufacturer standard
dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
54
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
H10 H10P
VET-074
Ball valve
1" 1 1/2"
ASME B16.34 (1)
fire tested ISO 10497 (2); monogram
API
butt weld ends
2500
A 105
split body
combined drain and vent
trunnion
full bore
AISI 410
Inconel X750
PEEK
-29C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing;
according MSS SP-25
locking device; anti-static device
manufacturer standard
dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
H3
VET-075
Ball valve
1" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
butt weld ends
2500
A 182 Grade F 316
split body
combined drain and vent
trunnion
full bore
AISI 316
Inconel X750
PEEK
-46C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing;
according MSS SP-25
locking device; anti-static device
manufacturer standard
dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
55
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
B4 C4
VET-076
Ball valve
1/2" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
socket weld with niple SCH 80
800
A 105
split body
combined drain and vent
floating
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 210C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
Test complement
according ISO 14313
(API 6D):
C12
VET-077
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 995 Grade 5A (UNS J93404)
split body
combined drain and vent
trunnion
full bore
A 995 Grade 5A (UNS J93404)
Inconel X750
PTFE reinforced with 25% of carbon
0C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
56
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
C12
VET-078
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
300
A 995 Grade 5A (UNS J93404)
split body
vent / drain plug in the cavity
trunnion
full bore
A 995 Grade 5A (UNS J93404)
Inconel X750
PTFE reinforced with 25% of carbon
0C to 150C
N/A
PTFE + Elgiloy
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
E30
VET-079
Ball valve
1/2" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
600
A 105 + Inconel 625 (UNS N06625)
split body
combined drain and vent
floating
full bore
AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing;
according MSS SP-25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
57
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B12
VET-081
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 995 Grade 5A (UNS J93404)
split body
combined drain and vent
trunnion
full bore
A 995 Grade 5A (UNS J93404)
Inconel X750
PTFE reinforced with 25% of carbon
0C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
B12
VET-082
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 995 Grade 5A (UNS J93404)
split body
vent / drain plug in the cavity
trunnion
full bore
A 995 Grade 5A (UNS J93404)
Inconel X750
PTFE reinforced with 25% of carbon
0C to 150C
N/A
PTFE + Elgiloy
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
58
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
B12
VET-083
Ball valve - double piston effect (DPE)
26" 36"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
150
A 995 Grade 5A (UNS J93404)
split body
vent / drain plug in the cavity
trunnion
full bore
A 995 Grade 5A (UNS J93404)
Inconel X750
PTFE reinforced with 25% of carbon
0C to 150C
N/A
PTFE + Elgiloy
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G12
VET-086
Ball valve
2" 3"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 995 Grade 5A (UNS J93404)
split body
combined drain and vent
trunnion
full bore
A 995 Grade 5A (UNS J93404)
Inconel X750
PEEK
0C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
59
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G12
VET-087
Ball valve - double piston effect (DPE)
4" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 995 Grade 5A (UNS J93404)
split body
vent / drain plug in the cavity
trunnion
full bore
A 995 Grade 5A (UNS J93404)
Inconel X750
PEEK
0C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
B12 C12
VET-088
Ball valve
1/2" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
socket weld with niple SCH 40S
800
A 182 Grade F 55 (UNS S32760)
split body
combined drain and vent
floating
full bore
A 182 Grade F 55 (UNS S32760)
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing;
according MSS SP-25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
60
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
G12
VET-089
Ball valve
1/2" 1 1/2"
ASME B16.34 (1)
fire tested ISO 10497 (2); monogram
API
socket weld with niple SCH 40S
1500
A 182 Grade F 55 (UNS S32760)
split body
combined drain and vent
trunnion
full bore
A 182 Grade F 55 (UNS S32760)
Inconel X750
PEEK
-46C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
Marking:
General requirement:
Bolt/nut:
Test:
Test complement
according ISO 14313
(API 6D):
Notes:
B14
VET-090
Ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; flat face (FF)
150
A 216 Grade WCB (3)
split body
combined drain and vent
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
Viton GLT
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D) (7)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
3 - Acceptable ASTM A 105
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
61
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B14
VET-091
Ball valve - double piston effect (DPE)
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; flat face (FF)
150
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
Viton GLT
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D) (7)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
B11
VET-092
Ball valve
1" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 105 + Inconel 625 (UNS N06625)
split body
combined drain and vent
floating
full bore
AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing;
according MSS SP-25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
62
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B11
VET-093
B11
VET-094
Ball valve
Ball valve - double piston effect (DPE)
2" 4"
6" 24"
ISO 14313 (API 6D) (1)
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
fire tested ISO 10497 (2); monogram
API
API
flange ASME B16.5; raised face (RF)
flange ASME B16.5; raised face (RF)
150
150
A 216 Grade WCB + Inconel 625
A 216 Grade WCB + Inconel 625
(UNS N06625) (3)
(UNS N06625)
split body
split body
combined drain and vent
vent / drain plug in the cavity
trunnion
trunnion
full bore
full bore
AISI 410 + Inconel 625 (UNS N06625) AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
Inconel X750
PTFE reinforced with 25% of carbon
PTFE reinforced with 25% of carbon
-29C to 150C
-29C to 150C
Viton GLT
Viton GLT
N/A
N/A
A 182 Grade F 316
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
63
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
G11
VET-095
Ball valve
1" 1 1/2"
ASME B16.34 (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
Ball valve
2" 3"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 216 Grade WCB + Inconel 625
A 105 + Inconel 625 (UNS N06625)
(UNS N06625)
split body
split body
combined drain and vent
combined drain and vent
Trunnion
trunnion
full bore
full bore
AISI 410 + Inconel 625 (UNS N06625) AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
Inconel X750
PEEK
PEEK
-29C to 150C
-29C to 150C
PTFE reinforced with 25% of carbon
Viton GLT
N/A
N/A
A 182 Grade F 316
Marking:
General requirement:
Bolt/nut:
Test:
Test complement
according ISO 14313
(API 6D):
Notes:
G11
VET-096
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
64
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
eneral requirement:
Bolt/nut:
Test:
Notes:
G11
VET-097
Ball valve - double piston effect (DPE)
4" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 216 Grade WCB + Inconel 625
(UNS N06625)
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
PEEK
-29C to 150C
Viton GLT
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
G11
VET-097
Ball valve - double piston effect (DPE)
4" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 216 Grade WCB + Inconel 625
(UNS N06625)
split body
vent / drain plug in the cavity
trunnion
full bore
AISI 410 + Inconel 625 (UNS N06625)
Inconel X750
PEEK
-29C to 150C
Viton GLT
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); automatic
thermal relief device from the body and
needle blocking valve, with calibration
certificate; sealant injection in the seat
and the stem; locking device; anti-static
device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
65
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
B14
VET-098
Ball valve
1/2" 1 1/2"
ISO 17292 (1)
fire tested ISO 10497 (2); monogram
API
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
150
A 105
split body
combined drain and vent
floating
full bore
AISI 410
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
PTFE reinforced with 25% of carbon
N/A
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
F14 G14
VET-099
Ball valve
1/2" 1 1/2"
ASME B16.34 (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 105
split body
combined drain and vent
trunnion
full bore
AISI 410
Inconel X750
PEEK
-29C to 150C
PTFE reinforced with 25% of carbon
N/A
A 182 Grade F 316
blow out proof stem, double seal
DU
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing;
according MSS SP-25
locking device; anti-static device
manufacturer standard
dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
66
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Drain:
Bore type:
Obturator (plug):
Slip seal:
Temperature:
Orings seal:
Lip seal:
Operator:
Test:
Marking:
General requirement:
Bolt/nut:
Test:
B3
VET-100
Plug valve with expanding slips
2 24
API 599
fire tested API 6FA; monogram API
flange ASME B16.5;
raised face (RF)
150
ASTM A 351 Grade CF8M
top entry and bottom entry
drain plug
reduced bore (not less than 70% of
nominal diameter)
ASTM A 351 Grade CF8M + Ni;
slip seats ASTM A 536 Grade 80-55-06
Viton GFLT
-46C to 150C
Viton GFLT
N/A
handwheel gear operator
ISO 14313 (API 6D)
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
B6
VET-103
Plug valve with expanding slips
2 24
API 599
fire tested API 6FA; monogram API
flange ASME B16.5;
raised face (RF)
150
ASTM A 352 Grade LCB
top entry and bottom entry
drain plug
reduced bore (not less than 70% of
nominal diameter)
ASTM A 352 Grade LCB + Ni;
slip seats ASTM A 536 Grade 80-55-06
Viton GFLT
-46C to 150C
Viton GFLT
N/A
handwheel gear operator
ISO 14313 (API 6D)
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
67
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Drain:
Bore type:
Obturator (plug):
Slip seal:
Temperature:
Orings seal:
Lip seal:
Operator:
Test:
Marking:
General requirement:
Bolt/nut:
Test:
B9 B10 B15
VET-105
Plug valve with expanding slips
2 24
API 599
fire tested API 6FA; monogram API
flange ASME B16.5;
raised face (RF)
150
ASTM A 216 Grade WCB
top entry and bottom entry
drain plug
reduced bore (not less than 70% of
nominal diameter)
ASTM A 216 Grade WCB + Ni;
slip seats ASTM A 536 Grade 80-55-06
Viton GF
-29C to 150C
Viton GF
N/A
handwheel gear operator
ISO 14313 (API 6D)
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
C3
VET-110
Plug valve with expanding slips
2 18
API 599
fire tested API 6FA; monogram API
flange ASME B16.5;
raised face (RF)
300
ASTM A 351 Grade CF8M
top entry and bottom entry
drain plug
reduced bore (not less than 70% of
nominal diameter)
ASTM A 351 Grade CF8M + Ni;
slip seats ASTM A 536 Grade 80-55-06
Viton GFLT
-46C to 150C
Viton GFLT
N/A
handwheel gear operator
ISO 14313 (API 6D)
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
68
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Drain:
Bore type:
Obturator (plug):
Slip seal:
Temperature:
Orings seal:
Lip seal:
Operator:
Test:
Marking:
General requirement:
Bolt/nut:
Test:
C6
VET-113
Plug valve with expanding slips
2 24
API 599
fire tested API 6FA; monogram API
flange ASME B16.5;
raised face (RF)
300
ASTM A 352 Grade LCB
top entry and bottom entry
drain plug
reduced bore (not less than 70% of
nominal diameter)
ASTM A 352 Grade LCB + Ni;
slip seats ASTM A 536 Grade 80-55-06
Viton GFLT
-46C to 150C
Viton GFLT
N/A
handwheel gear operator
ISO 14313 (API 6D)
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
C9 C10
VET-115
Plug valve with expanding slips
2 24
API 599
fire tested API 6FA; monogram API
flange ASME B16.5;
raised face (RF)
300
ASTM A 216 Grade WCB
top entry and bottom entry
drain plug
reduced bore (not less than 70% of
nominal diameter)
ASTM A 216 Grade WCB + Ni;
slip seats ASTM A 536 Grade 80-55-06
Viton GF
-29C to 150C
Viton GF
N/A
handwheel gear operator
ISO 14313 (API 6D)
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
69
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Drain:
Bore type:
Obturator (plug):
Slip seal:
Temperature:
Orings seal:
Lip seal:
Operator:
Test:
Marking:
General requirement:
Bolt/nut:
Test:
E3
VET-120
Plug valve with expanding slips
2 12
API 599
fire tested API 6FA; monogram API
flange ASME B16.5;
ring type joint (RTJ)
600
ASTM A 351 Grade CF8M
top entry and bottom entry
drain plug
reduced bore (not less than 70% of
nominal diameter)
ASTM A 351 Grade CF8M + Ni;
slip seats ASTM A 536 Grade 80-55-06
Viton GFLT
-46C to 150C
Viton GFLT
N/A
handwheel gear operator
ISO 14313 (API 6D)
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
E6 E6R
VET-123
Plug valve with expanding slips
2 24
API 599
fire tested API 6FA; monogram API
flange ASME B16.5;
raised face (RF)
300
ASTM A 352 Grade LCB
top entry and bottom entry
drain plug
reduced bore (not less than 70% of
nominal diameter)
ASTM A 352 Grade LCB + Ni;
slip seats ASTM A 536 Grade 80-55-06
Viton GFLT
-46C to 150C
Viton GFLT
N/A
handwheel gear operator
ISO 14313 (API 6D)
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
70
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Drain:
Bore type:
Obturator (plug):
Slip seal:
Temperature:
Orings seal:
Lip seal:
Operator:
Test:
Marking:
General requirement:
Bolt/nut:
Test:
E9 E10
VET-125
Plug valve with expanding slips
2 24
API 599
fire tested API 6FA; monogram API
flange ASME B16.5;
ring type joint (RTJ)
600
ASTM A 216 Grade WCB
top entry and bottom entry
drain plug
reduced bore (not less than 70% of
nominal diameter)
ASTM A 216 Grade WCB + Ni;
slip seats ASTM A 536 Grade 80-55-06
Viton GF
-29C to 150C
Viton GF
N/A
handwheel gear operator
ISO 14313 (API 6D)
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
F3
VET-130
Plug valve with expanding slips
2 10
API 599
fire tested API 6FA; monogram API
flange ASME B16.5; ring joint type
(RTJ);
2" apply 1500 class flanges;
4" - 10" apply 900 class flanges
900
ASTM A 351 Grade CF8M
top entry and bottom entry
drain plug
reduced bore (not less than 70% of
nominal diameter)
ASTM A 351 Grade CF8M + Ni;
slip seats ASTM A 536 Grade 80-55-06
Viton GFLT
-46C to 150C
Viton GFLT
N/A
handwheel gear operator
ISO 14313 (API 6D)
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
71
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Drain:
Bore type:
Obturator (plug):
Slip seal:
Temperature:
Orings seal:
Lip seal:
Operator:
Test:
Marking:
General requirement:
Bolt/nut:
Test:
F6 F6R
VET-133
Plug valve with expanding slips
2 10
API 599
fire tested API 6FA; monogram API
flange ASME B16.5; ring joint type
(RTJ);
2" apply 1500 class flanges;
4" - 10" apply 900 class flanges
300
ASTM A 352 Grade LCB
top entry and bottom entry
drain plug
reduced bore (not less than 70% of
nominal diameter)
ASTM A 352 Grade LCB + Ni;
slip seats ASTM A 536 Grade 80-55-06
Viton GFLT
-46C to 150C
Viton GFLT
N/A
handwheel gear operator
ISO 14313 (API 6D)
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
F10 F10R
VET-135
Plug valve with expanding slips
2 10
API 599
fire tested API 6FA; monogram API
flange ASME B16.5; ring joint type
(RTJ);
2" apply 1500 class flanges;
4" - 10" apply 900 class flanges
900
ASTM A 216 Grade WCB
top entry and bottom entry
drain plug
reduced bore (not less than 70% of
nominal diameter)
ASTM A 216 Grade WCB + Ni;
slip seats ASTM A 536 Grade 80-55-06
Viton GF
-29C to 150C
Viton GF
N/A
handwheel gear operator
ISO 14313 (API 6D)
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
72
of
193
TITLE:
APPENDIX 14
Spec
Tag
Class:
B12
VET-138
Plug valve with expanding slips
2 24
API 599
fire tested API 6FA; monogram API
flange ASME B16.5;
raised face (RF)
150
Body material:
Body type:
Drain:
Type:
NPS:
Standard:
Certificate:
End/finishing:
Bore type:
Obturator (plug):
Slip seal:
Temperature:
Orings seal:
Lip seal:
Operator:
Test:
Marking:
General requirement:
Bolt/nut:
Test:
B11
VET-140
Plug valve with expanding slips
2 24
API 599
fire tested API 6FA; monogram API
flange ASME B16.5;
raised face (RF)
150
ASTM A 216 Grade WCB + Inconel
625 (UNS N06625)
top entry and bottom entry
drain plug
reduced bore (not less than 70% of
nominal diameter)
ASTM A 216 Grade WCB + Inconel
625 (UNS N06625);
slip seats ASTM A 536 Grade 80-55-06
Viton GF
-29C to 150C
Viton GF
N/A
handwheel gear operator
ISO 14313 (API 6D)
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
73
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Reference standard
Certificate:
End/finishing:
Class:
Body material:
Body seat:
Obturator disc
material:
Obturator disc ring:
Stem material:
Stem:
Temperature:
Operator:
Pressure Tests:
Test complement
according ISO 14313
(API 6D):
Material pad:
Marking:
General requirement:
Non destructive Test:
B4 B10
VET-200
triple off set butterfly valve
10 24
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; raised face (RF);
short pattern, face to face dimensions
ISO 5752/BS EN 593
150
A 216 Grade WCB (3)
see note (4)
A 216 Grade WCB (3)
B10
VET-201
triple off set butterfly valve
26 36
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; raised face (RF);
short pattern, face to face dimensions
ISO 5752/BS EN 593
150
A 216 Grade WCB (3)
see note (4)
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
74
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Reference standard
Certificate:
End/finishing:
Class:
Body material:
Body seat:
Obturator disc
material:
Obturator disc ring:
Stem material:
Stem:
Temperature:
Operator:
Pressure Tests:
Test complement
according ISO 14313
(API 6D):
Material pad:
Marking:
General requirement:
Non destructive Test:
B7 B7R B15
VET-202
triple off set butterfly valve
12 24
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; raised face (RF);
short pattern, face to face dimensions
ISO 5752/BS EN 593
150
A 995 Grade 5A (3)
see note (4)
A 995 Grade 5A (3)
B7 B7R B15
VET- 203
triple off set butterfly valve
26 36
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; raised face (RF);
short pattern, face to face dimensions
ISO 5752/BS EN 593
150
A 995 Grade 5A (3)
see note (4)
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
75
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Reference standard
Certificate:
End/finishing:
Class:
Body material:
Body seat:
Obturator disc
material:
Obturator disc ring:
Stem material:
Stem:
Temperature:
Operator:
Pressure Tests:
Test complement
according ISO 14313
(API 6D):
Material pad:
Marking:
General requirement:
Non destructive Test:
B14 B22
VET-204
triple off set butterfly valve
10 24
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; raised face (RF);
short pattern, face to face dimensions
ISO 5752/BS EN 593
150
A 995 Grade 4A (3)
see note (4)
A 995 Grade 4A (3)
B14 B22
VET-205
triple off set butterfly valve
26 36
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; raised face (RF);
short pattern, face to face dimensions
ISO 5752/BS EN 593
150
A 995 Grade 4A (3)
see note (4)
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
76
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Reference standard
Certificate:
End/finishing:
Class:
Body material:
Body seat:
Obturator disc
material:
Obturator disc ring:
Stem material:
Stem:
Temperature:
Operator:
Pressure Tests:
Test complement
according ISO 14313
(API 6D):
Material pad:
Marking:
General requirement:
Non destructive Test:
C4 C10
VET-206
triple off set butterfly valve
10 24
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; raised face (RF);
short pattern, face to face dimensions
ISO 5752/BS EN 593
300
A 216 Grade WCB (3)
see note (4)
A 216 Grade WCB (3)
B6
VET- 208
triple off set butterfly valve
26 36
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; raised face (RF);
short pattern, face to face dimensions
ISO 5752/BS EN 593
150
A 352 Grade LCB (3)
see note (4)
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
77
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Reference standard
Certificate:
End/finishing:
Class:
Body material:
Body seat:
Obturator disc
material:
Obturator disc ring:
Stem material:
Stem:
Temperature:
Operator:
Pressure Tests:
Test complement
according ISO 14313
(API 6D):
Material pad:
Marking:
General requirement:
Non destructive Test:
B6
VET-209
triple off set butterfly valve
26 36
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; raised face (RF);
short pattern, face to face dimensions
ISO 5752/BS EN 593
150
A 352 Grade LCB (3)
see note (4)
A 352 Grade LCB (3)
C6
VET- 210
triple off set butterfly valve
10 24
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; raised face (RF);
short pattern, face to face dimensions
ISO 5752/BS EN 593
300
A 352 Grade LCB (3)
see note (4)
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
78
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Reference standard
Certificate:
End/finishing:
Class:
Body material:
Body seat:
Obturator disc
material:
Obturator disc ring:
Stem material:
Stem:
Temperature:
Operator:
Pressure Tests:
Test complement
according ISO 14313
(API 6D):
Material pad:
Marking:
General requirement:
Non destructive Test:
G10
VET-212
triple off set butterfly valve
10 24
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; ring type joint
(RTJ); short pattern, face to face
dimensions ISO 5752/BS EN 593
1500
A 216 Grade WCB (3)
see note (4)
A 216 Grade WCB (3)
B12
VET- 213
triple off set butterfly valve
10 24
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; raised face (RF);
short pattern, face to face dimensions
ISO 5752/BS EN 593
150
A 995 Grade 5A (3)
see note (4)
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
79
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Reference standard
Certificate:
End/finishing:
Class:
Body material:
Body seat:
Obturator disc
material:
Obturator disc ring:
Stem material:
Stem:
Temperature:
Operator:
Pressure Tests:
Test complement
according ISO 14313
(API 6D):
Material pad:
Marking:
General requirement:
Non destructive Test:
G12
VET- 214
triple off set butterfly valve
10 24
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; ring type joint
(RTJ); short pattern, face to face
dimensions ISO 5752/BS EN 593
1500
A 995 Grade 5A (3)
see note (4)
A 995 Grade 5A (3)
B11
VET- 216
triple off set butterfly valve
10 24
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; raised face (RF);
short pattern, face to face dimensions
ISO 5752/BS EN 593
150
A 995 Grade 4A (3)
see note (4)
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
80
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Reference standard
Certificate:
End/finishing:
Class:
Body material:
Body seat:
Obturator disc
material:
Obturator disc ring:
Stem material:
Stem:
Temperature:
Operator:
Pressure Tests:
Test complement
according ISO 14313
(API 6D):
Material pad:
Marking:
General requirement:
Non destructive Test:
G11
VET-218
triple off set butterfly valve
10 24
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; ring type joint
(RTJ); short pattern, face to face
dimensions ISO 5752/BS EN 593
1500
A 995 Grade 4A (3)
see note (4)
A 995 Grade 4A (3)
E17
VET- 221
triple off set butterfly valve
10 24
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; ring type joint
(RTJ); short pattern, face to face
dimensions ISO 5752/BS EN 593
600
A 216 Grade WCB (3)
see note (4)
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of
this appendix
TECHNICAL SPECIFICATION
E&P
N:
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Reference standard
Certificate:
End/finishing:
Class:
Body material:
Body seat:
Obturator disc
material:
Obturator disc ring:
Stem material:
Stem:
Temperature:
Operator:
Pressure Tests:
Test complement
according ISO 14313
(API 6D):
Material pad:
Marking:
General requirement:
Non destructive Test:
G16
VET- 222
triple off set butterfly valve
10 24
API 609 category B (1)
fire tested ISO 10497 (2)
flanged ASME B16.5; ring type joint
(RTJ); short pattern, face to face
dimensions ISO 5752/BS EN 593
1500
A 995 Grade 4A (3)
see note (4)
A 995 Grade 4A (3)
see note (5)
17-4PH (UNS S17400)
blow out proof stem, double seal
-46C to 130C
handwheel gear operator
test procedure according API 598 (6); full
rating according ASME B16.34
bidirectional;
anti-static testing; torque/thrust functional
testing
DU
according MSS SP-25
locking device; anti-static device
100% visual according MSS SP-55; die
penetrant in machined part; with
requirements described according of this
appendix
DR-ENGP-1.1
SHEET:
81
of
193
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
82
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator (plug):
Seat material:
Temperature:
Orings seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D) (8):
Marking:
General requirement:
Bolt and nut:
Test:
E3
VET-300
balanced plug valve
2" 4"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
600
A 351 Grade CF8M
solid body top entry
combined drain and vent
full bore
AISI 316 + Tungsten carbide
AISI 316 + Tungsten carbide
-46C to 150C
PTFE + BUNA - N + GRAFOIL
A 182 Grade F316
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium;
E3
VET-301
balanced plug valve
6" 8"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
600
A 351 Grade CF8M
solid body top entry
vent / drain plug in the cavity
full bore
AISI 316 + Tungsten carbide
AISI 316 + Tungsten carbide
-46C to 150C
PTFE + BUNA - N + GRAFOIL
A 182 Grade F316
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
handwheel (gear) operator
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
83
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator (plug):
Seat material:
Temperature:
Orings seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D) (8):
Marking:
General requirement:
Bolt and nut:
Test:
E4 E9 E10
VET-303
balanced plug valve
2" 4"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
600
A 216 Grade WCB
solid body top entry
combined drain and vent
full bore
AISI 410 + Tungsten carbide
AISI 410 + Tungsten carbide
-29C to 150C
PTFE + BUNA - N + GRAFOIL
AISI 410
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium;
E4 E9 E10
VET-304
balanced plug valve
6" 8"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
600
A 216 Grade WCB
solid body top entry
vent / drain plug in the cavity
full bore
AISI 410 + Tungsten carbide
AISI 410 + Tungsten carbide
-29C to 150C
PTFE + BUNA - N + GRAFOIL
A 182 Grade F316
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
handwheel (gear) operator
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
84
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator (plug):
Seat material:
Temperature:
Orings seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D) (8):
Marking:
General requirement:
Bolt and nut:
Test:
E6 E6R
VET-306
balanced plug valve
2" 5"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
600
A 352 Grade LCB
solid body top entry
combined drain and vent
full bore
AISI 304 + Tungsten carbide
AISI 304 + Tungsten carbide
-46C to 150C
PTFE + BUNA - N + GRAFOIL
A 182 Grade F316
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium;
E6 E6R
VET-307
balanced plug valve
6" 8"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
600
A 352 Grade LCB
solid body top entry
vent / drain plug in the cavity
full bore
AISI 304 + Tungsten carbide
AISI 304 + Tungsten carbide
-46C to 150C
PTFE + BUNA - N + GRAFOIL
A 182 Grade F316
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
handwheel (gear) operator
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
85
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator (plug):
Seat material:
Temperature:
Orings seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D) (8):
Marking:
General requirement:
Bolt and nut:
Test:
F10 F10R
VET-311
balanced plug valve
3" 4"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
900
A 216 Grade WCB
solid body top entry
combined drain and vent
full bore
AISI 410 + Tungsten carbide
AISI 410 + Tungsten carbide
-29C to 150C
PTFE + BUNA - N + GRAFOIL
AISI 410
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium;
F10 F10R
VET-312
balanced plug valve
6" 8"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
900
A 216 Grade WCB
solid body top entry
vent / drain plug in the cavity
full bore
AISI 410 + Tungsten carbide
AISI 410 + Tungsten carbide
-29C to 150C
PTFE + BUNA - N + GRAFOIL
AISI 410
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
handwheel (gear) operator
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
86
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator (plug):
Seat material:
Temperature:
Orings seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D) (8):
Marking:
General requirement:
Bolt and nut:
Test:
F3
VET-313
balanced plug valve
3" 4"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
F3
VET-314
balanced plug valve
6" 8"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
Flange ASME B16.5; ring type
flange ASME B16.5; ring type joint(RTJ)
joint(RTJ)
900
900
A 351 Grade CF8M
A 351 Grade CF8M
solid body top entry
solid body top entry
combined drain and vent
vent / drain plug in the cavity
full bore
full bore
AISI 316 + Tungsten carbide
AISI 316 + Tungsten carbide
AISI 316 + Tungsten carbide
AISI 316 + Tungsten carbide
-46C to 150C
-46C to 150C
PTFE + BUNA - N + GRAFOIL
PTFE + BUNA - N + GRAFOIL
A 182 Grade F316
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium;
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
87
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator (plug):
Seat material:
Temperature:
Orings seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D) (8):
Marking:
General requirement:
Bolt and nut:
Test:
G10P
VET-315P
balanced plug valve
2" 5"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
1500
A 216 Grade WCB
solid body top entry
vent / drain plug in the cavity
full bore
AISI 410 + Tungsten carbide
AISI 410 + Tungsten carbide
-29C to 150C
PTFE + BUNA - N + GRAFOIL
AISI 410
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
handwheel (gear) operator
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
88
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator (plug):
Seat material:
Temperature:
Orings seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D) (8):
Marking:
General requirement:
Bolt and nut:
Test:
G10P
VET-316P
balanced plug valve
6" 8"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
1500
A 216 Grade WCB
solid body top entry
vent / drain plug in the cavity
full bore
AISI 410 + Tungsten carbide
AISI 410 + Tungsten carbide
-29C to 150C
PTFE + BUNA - N + GRAFOIL
AISI 410
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
handwheel (gear) operator
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
89
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator (plug):
Seat material:
Temperature:
Orings seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D) (8):
Marking:
General requirement:
Bolt and nut:
Test:
F6 F6R
VET-317
balanced plug valve
3" 4"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
900
A 352 Grade LCB
solid body top entry
combined drain and vent
full bore
AISI 304 + Tungsten carbide
AISI 304 + Tungsten carbide
-46C to 150C
PTFE + BUNA - N + GRAFOIL
A 182 Grade F316
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium;
F6 F6R
VET-318
balanced plug valve
6" 8"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
900
A 352 Grade LCB
solid body top entry
vent / drain plug in the cavity
full bore
AISI 304 + Tungsten carbide
AISI 304 + Tungsten carbide
-46C to 150C
PTFE + BUNA - N + GRAFOIL
A 182 Grade F316
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
handwheel (gear) operator
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
90
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator (plug):
Seat material:
Temperature:
Orings seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D) (8):
Marking:
General requirement:
Bolt and nut:
Test:
F3 G3
VET-319
balanced plug valve
2" 4"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 351 Grade CF8M
solid body top entry
combined drain and vent
full bore
AISI 316 + Tungsten carbide
AISI 316 + Tungsten carbide
-46C to 150C
PTFE + BUNA - N + GRAFOIL
A 182 Grade F316
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium;
G3
VET-320
balanced plug valve
6" 8"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 351 Grade CF8M
solid body top entry
vent / drain plug in the cavity
full bore
AISI 316 + Tungsten carbide
AISI 316 + Tungsten carbide
-46C to 150C
PTFE + BUNA - N + GRAFOIL
A 182 Grade F316
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
handwheel (gear) operator
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
91
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator (plug):
Seat material:
Temperature:
Orings seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D) (8):
Marking:
General requirement:
Bolt and nut:
Test:
G6 G6R
VET-322
balanced plug valve
6" 8"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
1500
A 352 Grade LCB
solid body top entry
vent / drain plug in the cavity
full bore
AISI 304 + Tungsten carbide
AISI 304 + Tungsten carbide
-46C to 150C
PTFE + BUNA - N + GRAFOIL
A 182 Grade F316
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
handwheel (gear) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium;
F6 F6R G6 G6R
VET-321
balanced plug valve
2" 4"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
1500
A 352 Grade LCB
solid body top entry
combined drain and vent
full bore
AISI 304 + Tungsten carbide
AISI 304 + Tungsten carbide
-46C to 150C
PTFE + BUNA - N + GRAFOIL
A 182 Grade F316
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
wrench (lever) operator
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
92
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator (plug):
Seat material:
Temperature:
Orings seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D) (8):
Marking:
General requirement:
Bolt and nut:
Test:
H10
VET-325
balanced plug valve
2" 8"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
2500
A 216 Grade WCB
solid body top entry
combined drain and vent
full bore
AISI 410 + Tungsten carbide
AISI 410 + Tungsten carbide
-29C to 150C
PTFE + BUNA - N + GRAFOIL
A 182 Grade F316
G12P
VET-327P
balanced plug valve
6" 24"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
1500
ASTM A 995 Gr 5A (UNS J93404)
solid body top entry
vent / drain plug in the cavity
full bore
ASTM A 995 Gr 5A (UNS J93404)
ASTM A 995 Gr 5A (UNS J93404)
-46C to 150C
PTFE + BUNA - N + GRAFOIL
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
93
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator (plug):
Seat material:
Temperature:
Orings seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D) (8):
Marking:
General requirement:
Bolt and nut:
Test:
G11
VET-328
balanced plug valve
2" 4"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
1500
A 216 Grade WCB + Inconel
solid body top entry
combined drain and vent
full bore
AISI 410 + Tungsten carbide
AISI 410 + Tungsten carbide
-0C to 90C
PTFE + BUNA - N + GRAFOIL
AISI 410
G11
VET-329
balanced plug valve
6" 8"
ISO 14313 (API 6D)
fire tested ISO 10497; monogram API
flange ASME B16.5; ring type joint(RTJ)
1500
A 216 Grade WCB + Inconel
solid body top entry
vent / drain plug in the cavity
full bore
AISI 410 + Tungsten carbide
AISI 410 + Tungsten carbide
-29C to 150C
PTFE + BUNA - N + GRAFOIL
AISI 410
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
handwheel (gear) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antior nitrogen as the test medium; antistatic testing; Torque/thrust functional
static testing;
testing; cavity relief testing
according MSS SP-25
according MSS SP-25
anti-static testing; torque/thrust
anti-static testing; torque/thrust
functional testing; cavity relief testing;
functional testing; cavity relief testing;
Sealing injection for emergency
Sealing injection for emergency
situation
situation
according manufacturer standard
according manufacturer standard
100% visually casting according MSS
100% visually casting according MSS
SP-55; Dye penetrant in machined parts SP-55; Dye penetrant in machined parts
blow out proof stem, double seal
Thrust bearing + packing plate AISI
1018 SS
wrench (lever) operator
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
94
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Ball mounting:
Bore type:
Obturator (ball):
Seat:
Temperature:
Stem/trunnion
material:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B3
VET-401
rising stem ball valve
1 - 18
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2);
monogram API
flange ASME B16.5;
raised face (RF)
150
A 351 Grade CF8M
top entry;
solid body
trunnion
full bore
AISI 316
AISI 316 + tungsten carbide
-46C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
B6
VET-403
rising stem ball valve
2 - 18
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
raised face (RF)
150
A 352 Grade LCB
top entry;
solid body
trunnion
full bore
AISI 304
AISI 304 + tungsten carbide
-46C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
95
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Ball mounting:
Bore type:
Obturator (ball):
Seat:
Temperature:
Stem/trunnion
material:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B9 B10
VET-405
rising stem ball valve
1 - 18 (20 and 24)*
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
raised face (RF)
150
A 216 Grade WCB
top entry;
solid body
trunnion
full bore
AISI 410
AISI 410 + tungsten carbide
-29C to 150C
AISI 410
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
B12
VET-407
rising stem ball valve
1 - 18 (20 and 24)*
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
raised face (RF)
150
A 995 Grade 5A (UNS J93404)
top entry;
solid body
trunnion
full bore
A 995 Grade 5A (UNS J93404)
A 995 Grade 5A (UNS J93404)
0C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
96
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Ball mounting:
Bore type:
Obturator (ball):
Seat:
Temperature:
Stem/trunnion
material:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
C3
VET-409
rising stem ball valve
2 - 18
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
raised face (RF)
300
A 351 Grade CF8M
top entry;
solid body
trunnion
full bore
AISI 316
AISI 316 + tungsten carbide
-46C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
C6
VET-411
rising stem ball valve
2 - 20
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
raised face (RF)
300
A 352 Grade LCB
top entry;
solid body
trunnion
full bore
AISI 304
AISI 304 + tungsten carbide
-46C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
97
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Ball mounting:
Bore type:
Obturator (ball):
Seat:
Temperature:
Stem/trunnion
material:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
C9 C10
VET-413
rising stem ball valve
2 - 20
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
raised face (RF)
300
A 216 Grade WCB
top entry;
solid body
trunnion
full bore
AISI 410
AISI 410 + tungsten carbide
-29C to 150C
AISI 410
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
C12
VET-415
rising stem ball valve
2 - 20
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
raised face (RF)
300
A 995 Grade 5A (UNS J93404)
top entry;
solid body
trunnion
full bore
A 995 Grade 5A (UNS J93404)
A 995 Grade 5A (UNS J93404)
0C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
98
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Ball mounting:
Bore type:
Obturator (ball):
Seat:
Temperature:
Stem/trunnion
material:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
E3
VET-417
rising stem ball valve
2 - 12
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
ring type joint (RTJ)
600
A 351 Grade CF8M
top entry;
solid body
trunnion
full bore
AISI 316
AISI 316 + tungsten carbide
-46C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
E6 E6R
VET-419
rising stem ball valve
2 - 20
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
ring type joint (RTJ)
600
A 352 Grade LCB
top entry;
solid body
trunnion
full bore
AISI 304
AISI 304 + tungsten carbide
-46C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
99
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Ball mounting:
Bore type:
Obturator (ball):
Seat:
Temperature:
Stem/trunnion
material:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
E9 E10
VET-423
rising stem ball valve
2 - 20
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
ring type joint (RTJ)
600
A 216 Grade WCB
top entry;
solid body
trunnion
full bore
AISI 410
AISI 410 + tungsten carbide
-29C to 150C
AISI 410
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
F3
VET-427
rising stem ball valve
3 - 10
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
ring type joint (RTJ)
900
A 351 Grade CF8M
top entry;
solid body
trunnion
full bore
AISI 316
AISI 316 + tungsten carbide
-46C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
100
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Ball mounting:
Bore type:
Obturator (ball):
Seat:
Temperature:
Stem/trunnion
material:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
F6 F6R
VET-429
rising stem ball valve
3 - 10
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
ring type joint (RTJ)
900
A 352 Grade LCB
top entry;
solid body
trunnion
full bore
AISI 304
AISI 304 + tungsten carbide
-46C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
F10 F10R
VET-431
rising stem ball valve
3 - 18
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
ring type joint (RTJ)
900
A 216 Grade WCB
top entry;
solid body
trunnion
full bore
AISI 410
AISI 410 + tungsten carbide
-29C to 150C
AISI 410
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
101
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Ball mounting:
Bore type:
Obturator (ball):
Seat:
Temperature:
Stem/trunnion
material:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
F3 G3
VET-435
rising stem ball valve
2 - 12
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
ring type joint (RTJ)
900
A 351 Grade CF8M
top entry;
solid body
trunnion
full bore
AISI 316
AISI 316 + tungsten carbide
-46C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
3 - For NPS 2 valve flange class 1500
G6 G6R
VET-437
rising stem ball valve
2 - 10
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
ring type joint (RTJ)
1500
A 352 Grade LCB
top entry;
solid body
trunnion
full bore
AISI 304
AISI 304 + tungsten carbide
-46C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
102
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Ball mounting:
Bore type:
Obturator (ball):
Seat:
Temperature:
Stem/trunnion
material:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G12
VET-441
rising stem ball valve
1 - 12
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
ring type joint (RTJ)
1500
A 995 Grade 5A (UNS J93404)
top entry;
solid body
trunnion
full bore
A 995 Grade 5A (UNS J93404)
A 995 Grade 5A (UNS J93404)
0C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
103
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Ball mounting:
Bore type:
Obturator (ball):
Seat:
Temperature:
Stem/trunnion
material:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B11
VET-443
rising stem ball valve
1 - 18 (20 and 24)*
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
raised face (RF)
150
A 216 Grade WCB + Inconel 625
top entry;
solid body
trunnion
full bore
AISI 410 + Inconel 625
A 216 Grade WCB + Inconel 625
-29C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
G11
VET-445
rising stem ball valve
1 - 12
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5;
ring type joint (RTJ)
1500
A 216 Grade WCB + Inconel 625
top entry;
solid body
trunnion
full bore
AISI 410 + Inconel 625
A 216 Grade WCB + Inconel 625
-29C to 150C
17-4PH
rising stem
according ISO 14313 (API 6D);
bi-directional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
104
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
DN
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator:
Seat:
Temperature:
Orings seal:
Lip seal:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
F10 F10R
VET-500
Expanding gate valve
5 - 18
ISO 14313 (API 6D) (1)
fire tested API 6FA (2); monogram API
flange ASME B16.5; ring type joint
(RTJ)
900
A 216 Grade WCB
top entry;
bottom entry;
bolted bonnet
incorporated anular drain
full bore
AISI 410 + tungsten carbide
AISI 410 + tungsten carbide
-29C to 150C
PTFE
PTFE + Elgiloy
blow out proof stem;
double seal;
fugitive emissions tested
according ISO 14313 (API 6D)
anti-static testing; torque/thrust
functional testing; cavity relief testing
G10 G10R
VET-503
Expanding gate valve
2 - 24
ISO 14313 (API 6D) (1)
fire tested API 6FA (2); monogram API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 216 Grade WCB
top entry;
bottom entry;
bolted bonnet
incorporated anular drain
full bore
AISI 410 + tungsten carbide
AISI 410 + tungsten carbide
-29C to 150C
PTFE
PTFE + Elgiloy
blow out proof stem;
double seal;
fugitive emissions tested
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
105
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
DN
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator:
Seat:
Temperature:
Orings seal:
Lip seal:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G10P
VET-503P
Expanding gate valve
2 - 12
ISO 14313 (API 6D) (1)
fire tested API 6FA (2); monogram API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 216 Grade WCB
top entry;
bottom entry;
bolted bonnet
incorporated anular drain
piggable - internal diameter (ID) valve
shall be define for Project Engineer
AISI 410 + tungsten carbide
AISI 410 + tungsten carbide
-29C to 150C
PTFE
PTFE + Elgiloy
blow out proof stem;
double seal;
fugitive emissions tested
according ISO 14313 (API 6D)
anti-static testing; torque/thrust
functional testing; cavity relief testing
B10
VET-505
Expanding gate valve
5 - 24
ISO 14313 (API 6D) (1)
fire tested API 6FA (2); monogram API
flange ASME B16.5; raised face (RF)
150
A 216 Grade WCB
top entry;
bottom entry;
bolted bonnet
incorporated anular drain
full bore
AISI 410 + tungsten carbide
AISI 410 + tungsten carbide
-29C to 150C
PTFE
PTFE + Elgiloy
blow out proof stem;
double seal;
fugitive emissions tested
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
106
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
DN
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator:
Seat:
Temperature:
Orings seal:
Lip seal:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B12
VET-507
Expanding gate valve
6 - 24
ISO 14313 (API 6D) (1)
fire tested API 6FA (2); monogram API
flange ASME B16.5; raised face (RF)
150
A 995 Grade 5A (UNS J93404)
top entry;
bottom entry;
bolted bonnet
incorporated anular drain
full bore
wedge A 995 Grade 5A (UNS J93404) +
tungsten carbide
A 995 Grade 5A (UNS J93404) +
tungsten carbide
0C to 150C
PTFE
PTFE + Elgiloy
blow out proof stem;
double seal;
fugitive emissions tested
according ISO 14313 (API 6D)
anti-static testing; torque/thrust
functional testing; cavity relief testing
C12
VET-509
Expanding gate valve
5 - 24
ISO 14313 (API 6D) (1)
fire tested API 6FA (2); monogram API
flange ASME B16.5; raised face (RF)
300
A 995 Grade 5A (UNS J93404)
top entry;
bottom entry;
bolted bonnet
incorporated anular drain
full bore
wedge A 995 Grade 5A (UNS J93404) +
tungsten carbide
A 995 Grade 5A (UNS J93404) +
tungsten carbide
0C to 150C
PTFE
PTFE + Elgiloy
blow out proof stem;
double seal;
fugitive emissions tested
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
107
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
DN
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Bore type:
Obturator:
Seat:
Temperature:
Orings seal:
Lip seal:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
E10
VET-510
Expanding gate valve
5- 24
ISO 14313 (API 6D) (1)
fire tested API 6FA (2); monogram API
flange ASME B16.5; ring type joint
(RTJ)
600
A 216 Grade WCB
top entry;
bottom entry;
bolted bonnet
incorporated anular drain
full bore
AISI 410 + tungsten carbide
AISI 410 + tungsten carbide
-29C to 150C
PTFE
PTFE + Elgiloy
blow out proof stem;
double seal;
fugitive emissions tested
according ISO 14313 (API 6D)
anti-static testing; torque/thrust
functional testing; cavity relief testing
E10
VET-511
Expanding gate valve
26- 34
ISO 14313 (API 6D) (1)
fire tested API 6FA (2); monogram API
flange ASME B16.5; ring type joint
(RTJ)
600
A 216 Grade WCB
top entry;
bottom entry;
bolted bonnet
incorporated anular drain
full bore
AISI 410 + tungsten carbide
AISI 410 + tungsten carbide
-29C to 150C
PTFE
PTFE + Elgiloy
blow out proof stem;
double seal;
fugitive emissions tested
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
108
of
193
TITLE:
APPENDIX 14
Spec
Tag
Class:
G12
VET-513
Expanding gate valve
2 - 24
ISO 14313 (API 6D) (1)
fire tested API 6FA (2); monogram API
flange ASME B16.5; ring type joint
(RTJ)
1500
Body material:
Type:
DN
Standard:
Certificate:
End/finishing:
Body type:
Vent/drain:
Bore type:
Obturator:
Seat:
Temperature:
Orings seal:
Lip seal:
Stem:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
top entry;
bottom entry;
bolted bonnet
incorporated anular drain
full bore
wedge A 995 Grade 5A (UNS J93404) +
tungsten carbide
A 995 Grade 5A (UNS J93404) +
tungsten carbide
0C to 150C
PTFE
PTFE + Elgiloy
blow out proof stem;
double seal;
fugitive emissions tested
according ISO 14313 (API 6D)
anti-static testing; torque/thrust
functional testing; cavity relief testing
B11
VET-515
Expanding gate valve
6 - 24
ISO 14313 (API 6D) (1)
fire tested API 6FA (2); monogram API
flange ASME B16.5; raised face (RF)
150
A 216 Grade WCB + Inconel 625
(UNS N06625)
top entry;
bottom entry;
bolted bonnet
incorporated anular drain
full bore
wedge AISI 410 + Inconel 625 (UNS
N06625)
AISI 410 + Inconel 625 (UNS N06625)
-29C to 150C
PTFE
PTFE + Elgiloy
blow out proof stem;
double seal;
fugitive emissions tested
according ISO 14313 (API 6D)
TECHNICAL SPECIFICATION
E&P
N:
TITLE:
APPENDIX 14
Spec
Tag
Type:
DN
Standard:
Certificate:
End/finishing:
Class:
Body material:
G11
VET-517
Expanding gate valve
2 - 24
ISO 14313 (API 6D) (1)
fire tested API 6FA (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 216 Grade WCB + Inconel 625
(UNS N06625)
top entry;
bottom entry;
bolted bonnet
incorporated anular drain
Vent/drain:
full bore
Bore type:
wedge AISI 410 + Inconel 625
Obturator:
(UNS N06625)
AISI 410 + Inconel 625 (UNS
Seat:
N06625)
-29C to 150C
Temperature:
PTFE
Orings seal:
PTFE + Elgiloy
Lip seal:
blow out proof stem;
double seal;
Stem:
fugitive emissions tested
according ISO 14313 (API 6D)
Test:
Test complement
anti-static testing; torque/thrust
according ISO 14313 functional testing; cavity relief
testing
(API 6D):
according MSS SP-25
Marking:
double block expansible; without
friction between disc and seat
during opening and closing;
General
polished seats and plugs; fixed
seats; sealing mechanic action;
requirement:
sealant injection in the seat and the
stem; locking device; anti-static
device; outside screw and yoke
manufacturer standard
Bolt/nut:
100% visual casting according
MSS SP-55; dye penetrant in
Test:
machined parts
1 - it shall be according ASME
B16.34 and ASME section VIII
standard
Notes:
2 - All valve components shall be
fire test
Body type:
DR-ENGP-1.1
SHEET:
109
of
193
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
110
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Type/finishing:
Max. pressure:
Body material:
Body finishing:
Obturator (disc):
Disc finishing:
Stem:
Operator:
Temperature:
Test:
Test complement:
Marking:
Tests:
B7R B10
VET-600
Butterfly valve
2" 10"
API 609 categoriy A
wafer; raised face (RF), ASME B16.5
150 psig CWP
A 536 Grade 65-45-12
Viton B liner
A 536 Grade 65-45-12
coated Nylon 11
AISI 410
wrench (lever) operator
0C to 90C
according API 598, bidirectional
functional testing
according MSS SP-25
100% visual according MSS SP-55;
B7R B10
VET-601
Butterfly valve
12" 24"
API 609 categoriy A
wafer; raised face (RF), ASME B16.5
150 psig CWP
A 536 Grade 65-45-12
Viton B liner
A 536 Grade 65-45-12
coated Nylon 11
AISI 410
handwheel gear operator
0C to 90C
according API 598, bidirectional
functional testing
according MSS SP-25
100% visual according MSS SP-55;
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
111
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Type/finishing:
Max. pressure:
Body material:
Body finishing:
Obturator (disc):
Disc finishing:
Stem:
Operator:
Temperature:
Test:
Test complement:
Marking:
Tests:
B7R B10
VET-602
Butterfly valve
26" 36"
API 609 categoriy A
flanged; raised face (RF), ASME B16.5
150 psig CWP
A 536 Grade 65-45-12
Viton B liner
A 536 Grade 65-45-12
coated Nylon 11
AISI 410
handwheel gear operator
0C to 90C
according API 598, bidirectional
functional testing
according MSS SP-25
100% visual according MSS SP-55;
B7
VET-605
Butterfly valve
2" 8"
API 609 categoriy A
wafer; raised face (RF), ASME B16.5
250 psig CWP
A 536 Grade 65-45-12
Viton B liner
A 536 Grade 65-45-12
coated Nylon 11
AISI 410
wrench (lever) operator
0C to 90C
according API 598, bidirectional
functional testing
according MSS SP-25
100% visual according MSS SP-55;
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
112
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Type/finishing:
Max. pressure:
Body material:
Body finishing:
Obturator (disc):
Disc finishing:
Stem:
Operator:
Temperature:
Test:
Test complement:
Marking:
Tests:
B7
VET-606
Butterfly valve
10" 24"
API 609 categoriy A
wafer; raised face (RF), ASME B16.5
250 psig CWP
A 536 Grade 65-45-12
Viton B liner
A 536 Grade 65-45-12
coated Nylon 11
AISI 410
handwheel gear operator
0C to 90C
according API 598, bidirectional
functional testing
according MSS SP-25
100% visual according MSS SP-55;
B7
VET-607
Butterfly valve
26" 36"
API 609 categoriy A
flanged; raised face (RF), ASME B16.5
250 psig CWP
A 536 Grade 65-45-12
Viton B liner
A 536 Grade 65-45-12
coated Nylon 11
AISI 410
handwheel gear operator
0C to 90C
according API 598, bidirectional
functional testing
according MSS SP-25
100% visual according MSS SP-55;
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
113
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Type/finishing:
Max. pressure:
Body material:
Body finishing:
Obturator (disc):
Disc finishing:
Stem:
Operator:
Temperature:
Test:
Test complement:
Marking:
Tests:
B14 B22
VET-610
Butterfly valve
2" 10"
API 609 categoriy A
wafer; raised face (RF), ASME B16.5
150 psig CWP
A 536 Grade 65-45-12
Viton B liner
A 536 Grade 65-45-12
coated Nylon 11
AISI 410
wrench (lever) operator
0C to 90C
according API 598, bidirectional
functional testing
according MSS SP-25
100% visual according MSS SP-55;
B14 B22
VET-611
Butterfly valve
12" 24"
API 609 categoriy A
wafer; raised face (RF), ASME B16.5
150 psig CWP
A 536 Grade 65-45-12
Viton B liner
A 536 Grade 65-45-12
coated Nylon 11
AISI 410
handwheel gear operator
0C to 90C
according API 598, bidirectional
functional testing
according MSS SP-25
100% visual according MSS SP-55;
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
114
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Type/finishing:
Max. pressure:
Body material:
Body finishing:
Obturator (disc):
Disc finishing:
Stem:
Operator:
Temperature:
Test:
Test complement:
Marking:
Tests:
B14 B22
VET-612
Butterfly valve
26" 44"
API 609 categoriy A
flanged; raised face (RF), ASME B16.5
150 psig CWP
A 536 Grade 65-45-12
Viton B liner
A 536 Grade 65-45-12
coated Nylon 11
AISI 410
handwheel gear operator
0C to 90C
according API 598, bidirectional
functional testing
according MSS SP-25
100% visual according MSS SP-55;
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
115
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Type/finishing:
Max. pressure:
Body material:
Body finishing:
Obturator (disc):
Disc finishing:
Stem:
Operator:
Temperature:
Test:
Test complement:
Marking:
Tests:
B7R B10
VET-617
Butterfly valve
26" 36"
API 609 categoriy A
flanged; raised face (RF), ASME B16.5
250 psig CWP
A 536 Grade 65-45-12
Viton B liner
A 536 Grade 65-45-12
coated Nylon 11
AISI 410
handwheel gear operator
0C to 90C
according API 598, bidirectional
functional testing
according MSS SP-25
100% visual according MSS SP-55;
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
116
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body mounting:
Seat:
Obturator (ball):
Sealing Ring:
Stem / trunnion
material:
Oring Seal:
Lip Seal:
Operator:
Temperature:
Test:
Test complement
according ISO 14313
(API 6D) (7):
General requirement
test.
Bolts and nuts
Marking:
Test:
C6
VET-713
Triple off set ball valve
2 24
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; raised face (RF)
300
A 352 Grade LCB
trunnion
AISI 304 + Tungsten Carbide
AISI 304 + with electroless Niquel
plating
A 790 (UNS S31803)
A 182 Grade F316
C12
VET-714
Triple off set ball valve
2 24
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; raised face (RF)
300
A 995 Gr 5A (UNS J93404)
trunnion
A 995 Gr 5A + Tungsten Carbide
A 995 Grade 5A with electroless Niquel
plating
A 790 (UNS S31803)
N/A
PTFE + Elgiloy
handhweel gear operator
-46C to 150C
according ISO 14313 (API 6D);
Bidirectional
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
117
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
C16
VET-715
Triple off set ball valve
2 24
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
End/finishing:
Class:
Body material:
Body mounting:
Seat:
300
A 995 Gr 4A (UNS J92205)
trunnion
A 995 Gr 4A + Tungsten Carbide
A 995 Grade 4A with electroless Niquel
plating
A 790 (UNS S31803)
Obturator (ball):
Sealing Ring:
Stem / trunnion
material:
Oring Seal:
Lip Seal:
Operator:
Temperature:
Test:
Test complement
according ISO 14313
(API 6D) (7):
General requirement
test.
Bolts and nuts
Marking:
Test:
E3
VET-717
Triple off set ball valve
2 16
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
600
A 351 Grade CF8M
trunnion
A 351 Grade CF8M + Tungsten Carbide
A 351 Grade CF8M with electroless
Niquel plating
A 790 (UNS S31803)
N/A
PTFE + Elgiloy
handhweel gear operator
-46C to 150C
according ISO 14313 (API 6D);
Bidirectional
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
118
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body mounting:
Seat:
Obturator (ball):
Sealing Ring:
Stem / trunnion
material:
Oring Seal:
Lip Seal:
Operator:
Temperature:
Test:
Test complement
according ISO 14313
(API 6D) (7):
General requirement
test.
Bolts and nuts
Marking:
Test:
E4 E9 E10 E17
VET-718
Triple off set ball valve
2 16
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
600
A 216 Grade WCB
trunnion
A 216 Grade WCB + Tungsten Carbide
A 216 Grade WCB with electroless
Niquel plating
A 790 (UNS S31803)
AISI 410
E6 E6R
VET-719
Triple off set ball valve
2 16
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
600
A 352 Grade LCB
trunnion
AISI 304 + Tungsten Carbide
AISI 304 + with electroless Niquel
plating
A 790 (UNS S31803)
Viton B
PTFE + Elgiloy
handhweel gear operator
-29C to 150C
according ISO 14313 (API 6D);
Bidirectional
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
119
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body mounting:
Seat:
Obturator (ball):
Sealing Ring:
Stem / trunnion
material:
Oring Seal:
Lip Seal:
Operator:
Temperature:
Test:
Test complement
according ISO 14313
(API 6D) (7):
General requirement
test.
Bolts and nuts
Marking:
Test:
E16
VET-720
Triple off set ball valve
2 16
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
600
A 995 Gr 4A (UNS J92205)
trunnion
A 995 Grade 4A + Tungsten Carbide
A 995 Grade 4A with electroless Niquel
plating
A 790 (UNS S31803)
17-4PH (UNS 17400)
F3
VET-721
Triple off set ball valve
2 14
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
900
A 351 Grade CF8M
trunnion
A 351 Grade CF8M + Tungsten Carbide
A 351 Grade CF8M with electroless
Niquel plating
A 790 (UNS S31803)
N/A
PTFE + Elgiloy
handhweel gear operator
-46C to 150C
according ISO 14313 (API 6D);
Bidirectional
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
120
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body mounting:
Seat:
Obturator (ball):
Sealing Ring:
Stem / trunnion
material:
Oring Seal:
Lip Seal:
Operator:
Temperature:
Test:
Test complement
according ISO 14313
(API 6D) (7):
General requirement
test.
Bolts and nuts
Marking:
Test:
F6 F6R
VET-722
Triple off set ball valve
2 14
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
900
A 352 Grade LCB
trunnion
AISI 304 + Tungsten Carbide
AISI 304 + with electroless Niquel
plating
A 790 (UNS S31803)
A 182 Grade F316
F10 F10R
VET-723
Triple off set ball valve
2 14
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
900
A 216 Grade WCB
trunnion
A 216 WCB + Tungsten Carbide
A 216 Grade WCB with electroless
Niquel plating
A 790 (UNS S31803)
N/A
PTFE + Elgiloy
handhweel gear operator
-46C to 150C
according ISO 14313 (API 6D);
Bidirectional
AISI 410
Viton B
PTFE + Elgiloy
handhweel gear operator
-29C to 150C
according ISO 14313 (API 6D);
Bidirectional
TECHNICAL SPECIFICATION
E&P
N:
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body mounting:
Seat:
Obturator (ball):
Sealing Ring:
Stem / trunnion
material:
Oring Seal:
Lip Seal:
Operator:
Temperature:
Test:
Test complement
according ISO 14313
(API 6D) (7):
General requirement
test.
Bolts and nuts
Marking:
Test:
G3
VET-725
Triple off set ball valve
2 12
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 351 Grade CF8M
trunnion
A 351 Grade CF8M + Tungsten Carbide
A 351 Grade CF8M with electroless
Niquel plating
A 790 (UNS S31803)
A 182 Grade F316
N/A
PTFE + Elgiloy
handhweel gear operator
-46C to 150C
according ISO 14313 (API 6D);
Bidirectional
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; Anti
static test; Tork / thrust functional test;
locking device; anti static device;
manufacturer standard
according MSS SP-25
100% visual casting according MSS SP55; dye penetrant in machined parts
DR-ENGP-1.1
SHEET:
121
of
193
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
122
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body mounting:
Seat:
Obturator (ball):
Sealing Ring:
Stem / trunnion
material:
Oring Seal:
Lip Seal:
Operator:
Temperature:
Test:
Test complement
according ISO 14313
(API 6D) (7):
General requirement
test.
Bolts and nuts
Marking:
Test:
G6 G6R
VET-726
Triple off set ball valve
2 12
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 352 Grade LCB
trunnion
AISI 304 + Tungsten Carbide
AISI 304 + with electroless Niquel
plating
A 790 (UNS S31803)
A 182 Grade F316
G10 G10R
VET-732
Triple off set ball valve
2 12
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 216 Grade WCB
trunnion
A 216 WCB + Tungsten Carbide
A 216 Grade WCB with electroless
Niquel plating
A 790 (UNS S31803)
N/A
PTFE + Elgiloy
handhweel gear operator
-46C to 150C
according ISO 14313 (API 6D);
Bidirectional
AISI 410
Viton B
PTFE + Elgiloy
handhweel gear operator
-29C to 150C
according ISO 14313 (API 6D);
Bidirectional
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
123
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body mounting:
Seat:
Obturator (ball):
Sealing Ring:
Stem / trunnion
material:
Oring Seal:
Lip Seal:
Operator:
Temperature:
Test:
Test complement
according ISO 14313
(API 6D) (7):
General requirement
test.
Bolts and nuts
Marking:
Test:
G12
VET-728
Triple off set ball valve
2 12
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 995 Grade 5A (UNS J93404)
trunnion
A 995 Grade 5A + Tungsten Carbide
A 995 Grade 5A with electroless Niquel
plating
A 790 (UNS S31803)
17-4PH (UNS 17400)
G16
VET-729
Triple off set ball valve
2 12
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 995 Grade 4A (UNS J92205)
trunnion
A 995 Grade 4A + Tungsten Carbide
A 995 Grade 4A with electroless Niquel
plating
A 790 (UNS S31803)
N/A
PTFE + Elgiloy
handhweel gear operator
-46C to 150C
according ISO 14313 (API 6D);
Bidirectional
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
124
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body mounting:
Seat:
Obturator (ball):
Sealing Ring:
Stem / trunnion
material:
Oring Seal:
Lip Seal:
Operator:
Temperature:
Test:
Test complement
according ISO 14313
(API 6D) (7):
General requirement
test.
Bolts and nuts
Marking:
Test:
H3
VET-730
Triple off set ball valve
2 6
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 351 Grade CF8M
trunnion
A 351 Grade CF8M + Tungsten Carbide
A 351 Grade CF8M with electroless
Niquel plating
A 790 (UNS S31803)
A 182 Grade F316
H10
VET-731
Triple off set ball valve
2 6
ISO 14313 (API 6D)
fire tested ISO 10497;
monogram API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 216 Grade WCB
trunnion
A 216 WCB + Tungsten Carbide
A 216 WCB + Tungsten Carbide
A 790 (UNS S31803)
N/A
PTFE + Elgiloy
handhweel gear operator
-46C to 150C
according ISO 14313 (API 6D);
Bidirectional
AISI 410
Viton B
PTFE + Elgiloy
handhweel gear operator
-29C to 150C
according ISO 14313 (API 6D);
Bidirectional
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
125
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
B10 B15
VET-801
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
flanged ASME B16.5; raised face (RF);
according MSS SP-6; ISO 5752 short
pattern
150
ASTM A 216 Grade WCB
RPTFE
ASTM A 351 CF8M
B10 B15
VET-802
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
flanged ASME B16.5; raised face (RF);
according MSS SP-6; ISO 5752 short
pattern
150
ASTM A 216 Grade WCB
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
126
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
B10 B15
VET-803
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
wafer; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM A 216 Grade WCB
RPTFE
ASTM A 351 CF8M
B10 B15
VET-804
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
wafer; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM A 216 Grade WCB
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
127
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
B10 B15
VET-805
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
lug; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM A 216 Grade WCB
RPTFE
ASTM A 351 CF8M
B10 B15
VET-806
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
lug; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM A 216 Grade WCB
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
128
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
B3
VET-821
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
flanged ASME B16.5; raised face (RF);
according MSS SP-6; ISO 5752 short
pattern
150
ASTM A 351 Grade CF8M
RPTFE
ASTM A 351 CF8M
B3
VET-822
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
flanged ASME B16.5; raised face (RF);
according MSS SP-6; ISO 5752 short
pattern
150
ASTM A 351 Grade CF8M
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
129
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
B3
VET-823
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
wafer; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM A 351 Grade CF8M
RPTFE
ASTM A 351 CF8M
B3
VET-824
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
wafer; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM A 351 Grade CF8M
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
130
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
B3
VET-825
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
lug; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM A 351 Grade CF8M
RPTFE
ASTM A 351 CF8M
B3
VET-826
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
lug; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM A 351 Grade CF8M
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
131
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
B16
VET-827
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
flanged ASME B16.5; raised face (RF);
according MSS SP-6; ISO 5752 short
pattern
150
ASTM A 995 Grade 4A (UNS J 92205)
RPTFE
ASTM A 995 4A (3)
B16
VET-828
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
flanged ASME B16.5; raised face (RF);
according MSS SP-6; ISO 5752 short
pattern
150
ASTM A 995 Grade 4A (UNS J 92205)
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
132
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
B16
VET-829
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
wafer; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM A 995 Grade 4A (UNS J 92205)
RPTFE
ASTM A 995 4A (3)
B16
VET-830
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
wafer; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM A 995 Grade 4A (UNS J 92205)
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
133
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
B16
VET-831
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
lug; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM A 995 Grade 4A (UNS J 92205)
RPTFE
ASTM A 995 4A (3)
B16
VET-832
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
lug; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM A 995 Grade 4A (UNS J 92205)
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
134
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
C16
VET-833
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
flanged ASME B16.5; raised face (RF);
according MSS SP-6; ISO 5752 short
pattern
300
ASTM A 995 Grade 4A (UNS J 92205)
RPTFE
ASTM A 995 4A (3)
C16
VET-834
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
flanged ASME B16.5; raised face (RF);
according MSS SP-6; ISO 5752 short
pattern
300
ASTM A 995 Grade 4A (UNS J 92205)
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
135
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
C16
VET-835
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
wafer; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
300
ASTM A 995 Grade 4A (UNS J 92205)
RPTFE
ASTM A 995 4A (3)
C16
VET-836
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
wafer; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
300
ASTM A 995 Grade 4A (UNS J 92205)
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
136
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
C16
VET-837
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
lug; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
300
ASTM A 995 Grade 4A (UNS J 92205)
RPTFE
ASTM A 995 4A (3)
C16
VET-838
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
lug; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
300
ASTM A 995 Grade 4A (UNS J 92205)
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
137
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
B7
VET-851
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
flanged ASME B16.5; raised face (RF);
according MSS SP-6; ISO 5752 short
pattern
150
ASTM B 148 (UNS C95800)
RPTFE
ASTM B 148 UNS C95800
B7
VET-852
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
flanged ASME B16.5; raised face (RF);
according MSS SP-6; ISO 5752 short
pattern
150
ASTM B 148 (UNS C95800)
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
138
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
B7
VET-853
Bi Off Set Butterfly valve
6" 24"
API 609 categoriy B
fire tested ISO 10497
wafer; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM B 148 (UNS C95800)
RPTFE
ASTM B 148 UNS C95800
B7
VET-854
Bi Off Set Butterfly valve
26" 40"
API 609 categoriy B
fire tested ISO 10497
wafer; assembly flange ASME B16.5;
raised face (RF); according MSS SP-6;
ISO 5752 short pattern
150
ASTM B 148 (UNS C95800)
RPTFE
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
139
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Seat insert:
Obturator disc
material:
Stem:
Operator:
Temperature:
Test:
Marking:
Tests:
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
140
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B11
VET-901
Metal to metal ball valve
1" 1 1/2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 105 + Inconel 625 (UNS N06625)
split body
combined drain and vent
floating
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
B4 B9 B10 B17
VET-902A
Metal to metal ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 216 Grade WCB (3)
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
141
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
B4 B9 B10 B17
VET-902B
Metal to metal ball valve
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
150
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
C11
VET-904
Metal to metal ball valve
1" 1 1/2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 105 + Inconel 625 (UNS N06625)
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
142
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
C11 C30
VET-905A
Metal to metal ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 216 Grade WCB + Inconel 625
(UNS N06625)
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
C11 C30
VET-905B
Metal to metal ball valve
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; raised face (RF)
300
A 216 Grade WCB + Inconel 625
(UNS N06625)
split body
vent / drain plug in the cavity
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
143
of
193
TITLE:
APPENDIX 14
Espec
Tag
Class:
H30 H30P
VET-906
Metal to metal ball valve
1" 1 1/2"
ASME B16.34 (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
Type:
NPS:
Standard:
Certificate:
End/finishing:
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
H30
VET-907A
Metal to metal ball valve
2" 3"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 216 Grade WCB + Inconel 625
(UNS N06625) (3)
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
blow out proof stem, double seal;
construction TA-Luft
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
3 - Acceptable ASTM A 105
4 - Nickel coating with 500 to 700
microns, 62 HRC Min. Cr-17%, Ni-70%,
Si-4% applied by flame spraying.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
144
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
H30
VET-907B
Metal to metal ball valve
4" 12"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 216 Grade WCB + Inconel 625
(UNS N06625)
split body
vent / drain plug in the cavity
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
blow out proof stem, double seal;
construction TA-Luft
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate; sealant injection in
the seat and the stem; locking device;
anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
4 - Nickel coating with 500 to 700
microns, 62 HRC Min. Cr-17%, Ni-70%,
Si-4% applied by flame spraying.
H30P
VET-907BP
Metal to metal ball valve piggable
4" 12"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 216 Grade WCB + Inconel 625
(UNS N06625)
split body
vent / drain plug in the cavity
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
blow out proof stem, double seal;
construction TA-Luft
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate; sealant injection in
the seat and the stem; locking device;
anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
4 - Nickel coating with 500 to 700
microns, 62 HRC Min. Cr-17%, Ni-70%,
Si-4% applied by flame spraying.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
145
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
H30
VET-907C
Metal to metal ball valve
14" - 20"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
compact flange NORSOK L-005; seal
type IX (MSJ)
2500
A 216 Grade WCB + Inconel 625
(UNS N06625)
split body
vent / drain plug in the cavity
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
blow out proof stem, double seal;
construction TA-Luft
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate; sealant injection in
the seat and the stem; locking device;
anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
4 - Nickel coating with 500 to 700
microns, 62 HRC Min. Cr-17%, Ni-70%,
Si-4% applied by flame spraying.
H30P
VET-907CP
Metal to metal ball valve piggable
14" - 20"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
compact flange NORSOK L-005; seal
type IX (MSJ)
2500
A 216 Grade WCB + Inconel 625
(UNS N06625)
split body
vent / drain plug in the cavity
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
blow out proof stem, double seal;
construction TA-Luft
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate; sealant injection in
the seat and the stem; locking device;
anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
4 - Nickel coating with 500 to 700
microns, 62 HRC Min. Cr-17%, Ni-70%,
Si-4% applied by flame spraying.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
146
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
E9 E10
VET-918A
Metal to metal ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
600
A 216 Grade WCB (3)
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
E9 E10
VET-918B
Metal to metal ball valve
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
600
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
147
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
F3
VET-921A
Metal to metal ball valve
3" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
900
A 351 Grade CF8M (3)
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-46C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
blow out proof stem, double seal;
construction TA-Luft
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
3 - Acceptable ASTM A 182 grade F
316
4 - Nickel coating with 500 to 700
microns, 62 HRC Min. Cr-17%, Ni-70%,
Si-4% applied by flame spraying.
F3
VET-921B
Metal to metal ball valve
6" 10"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
900
A 351 Grade CF8M
split body
vent / drain plug in the cavity
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-46C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
blow out proof stem, double seal;
construction TA-Luft
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
4 - Nickel coating with 500 to 700
microns, 62 HRC Min. Cr-17%, Ni-70%,
Si-4% applied by flame spraying.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
148
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
F3
VET-924
Metal to metal ball valve
1" 1 1/2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
socket weld with niple
1" SCH 40S
1 " SCH 80S
900
A 182 Grade F 316
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-46C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
Marking:
General requirement:
Bolt/nut:
manufacturer standard
Test:
Notes:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
F3
VET-925A
Metal to metal ball valve
2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
900
A 351 Grade CF8M (3)
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-46C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
blow out proof stem, double seal;
construction TA-Luft
wrench (lever) operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
sealant injection in the seat and the
stem; locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
3 - Acceptable ASTM A 182 Grade F
316
4 - Nickel coating with 500 to 700
microns, 62 HRC Min. Cr-17%, Ni-70%,
Si-4% applied by flame spraying.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
149
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G16
VET-929A
Metal to metal ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 995 Grade 4A (UNS J92205) (3)
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
0C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
G16
VET-929B
Metal to metal ball valve
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 995 Grade 4A (UNS J92205)
split body
vent / drain plug in the cavity
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
0C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
150
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G16P
VET-929AP
Metal to metal ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 995 Grade 4A (UNS J92205) (3)
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
0C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
G16P
VET-929BP
Metal to metal ball valve piggable
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 995 Grade 4A (UNS J92205)
split body
vent / drain plug in the cavity
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
0C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
151
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
H10 H10P
VET-931A
Metal to metal ball valve
2" 3"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 216 Grade WCB (3)
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
H10
VET-931B
Metal to metal ball valve
4" 12"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 216 Grade WCB (3)
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
152
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
H10P
VET-931BP
Metal to metal ball valve piggable
4" 12"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
2500
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
G10 G10R
VET-940A
Metal to metal ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 216 Grade WCB (3)
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
3 - Acceptable ASTM A 105
4 - Nickel coating with 500 to 700
microns, 62 HRC Min. Cr-17%, Ni-70%,
Si-4% applied by flame spraying.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
153
of
193
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G10 G10R
VET-940B
Metal to metal ball valve
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
G10P
VET-940AP
Metal to metal ball valve
2" 4"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ)
1500
A 216 Grade WCB (3)
split body
combined drain and vent
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
3 - Acceptable ASTM A 105
4 - Nickel coating with 500 to 700
microns, 62 HRC Min. Cr-17%, Ni-70%,
Si-4% applied by flame spraying.
TECHNICAL SPECIFICATION
E&P
N:
TITLE:
APPENDIX 14
Espec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat:
Temperature:
Body orings:
Stem orings:
Stem/trunnion
material:
Stem:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G10P
VET-940BP
Metal to metal ball valve piggable
6" 24"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram API
flange ASME B16.5; ring type joint (RTJ)
1500
A 216 Grade WCB
split body
vent / drain plug in the cavity
trunnion
full bore
A 351 CF8M (4)
A 182 Grade F 316Ti
A 182 Grade F 316Ti (4)
-29C to 150C
celastic + EBZ + Inconel 625
celastic + PTFE (TA-Luft certificate)
17-4PH (UNS S17400)
blow out proof stem, double seal;
construction TA-Luft
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
automatic thermal relief device from the
body and needle blocking valve, with
calibration certificate; sealant injection in
the seat and the stem; locking device;
anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire test
4 - Nickel coating with 500 to 700
microns, 62 HRC Min. Cr-17%, Ni-70%,
Si-4% applied by flame spraying.
DR-ENGP-1.1
SHEET:
154
of
193
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
155
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
Drilling/finishing
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
E3
VET-1001
single body double ball, compact valve
ASME B16.10
3" 6"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
600
A 351 Grade CF8M
mono-block
needle valve integrated;
plug drain
trunnion
full bore
AISI 316
Inconel X750
Devlon V
-46C to 150C
N/A
PTFE + Elgiloy
F3
VET-1002
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
900
A 351 Grade CF8M
mono-block
needle valve integrated;
plug drain
trunnion
full bore
AISI 316
Inconel X750
Devlon V
-46C to 150C
N/A
PTFE + Elgiloy
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
156
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
Drilling/finishing
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G3
VET-1003
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
1500
A 351 Grade CF8M
mono-block
needle valve integrated;
plug drain
trunnion
full bore
AISI 316
Inconel X750
PEEK
-46C to 150C
N/A
PTFE + Elgiloy
E16
VET-1004
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
1500
A 995 Grade 4A (UNS J92205)
mono-block
needle valve integrated;
plug drain
trunnion
full bore
A 995 Grade 4A (UNS J92205)
Inconel X750
PEEK
0C to 150C
Viton GLT
N/A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
157
of
193
TITLE:
APPENDIX 14
Spec
Tag
Ball mounting:
G16
VET-1005
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
1500
A 995 Grade 4A (UNS J92205)
mono-block
needle valve integrated;
plug drain
trunnion
Bore type:
full bore
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Type:
NPS:
Standard:
Certificate:
Drilling/finishing
Class:
Body material:
Body type:
Vent/drain:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G16P
VET-1005P
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
1500
A 995 Grade 4A (UNS J92205)
mono-block
needle valve integrated;
plug drain
trunnion
piggable - internal diameter (ID) valve
shall be
defined by Project Engineer
A 995 Grade 4A (UNS J92205)
Inconel X750
PEEK
0C to 150C
Viton GLT
N/A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
158
of
193
TITLE:
APPENDIX 14
Spec
Tag
Ball mounting:
E10 E17
VET-1006
single body double ball, compact valve
ASME B16.10
3" 6"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
600
A 216 Grade WCB
mono-block
needle valve integrated;
plug drain
trunnion
Bore type:
full bore
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
AISI 410
Inconel X750
Devlon V
-29C to 150C
Viton GLT
N/A
Type:
NPS:
Standard:
Certificate:
Drilling/finishing
Class:
Body material:
Body type:
Vent/drain:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
E10P
VET-1006P
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
159
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
Drilling/finishing
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
F10P
VET-1008P
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
900
A 216 Grade WCB
mono-block
needle valve integrated;
plug drain
trunnion
piggable - internal diameter (ID) valve
shall be
defined by Project Engineer
AISI 410
Inconel X750
Devlon V
-29C to 150C
Viton GLT
N/A
F10 F10R
VET-1008
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
900
A 216 Grade WCB
mono-block
needle valve integrated;
plug drain
trunnion
full bore
AISI 410
Inconel X750
Devlon V
-29C to 150C
Viton GLT
N/A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
160
of
193
TITLE:
APPENDIX 14
Spec
Tag
Ball mounting:
G10 G10R
VET-1010
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
1500
A 216 Grade WCB
mono-block
needle valve integrated;
plug drain
trunnion
Bore type:
full bore
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
AISI 410
Inconel X750
PEEK
-29C to 150C
Viton GLT
N/A
Type:
NPS:
Standard:
Certificate:
Drilling/finishing
Class:
Body material:
Body type:
Vent/drain:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G10P
VET-1010P
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
161
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
Drilling/finishing
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
G12
VET-1011
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
1500
A 995 Grade 5A (UNS J93404)
mono-block
needle valve integrated;
plug drain
trunnion
full bore
A 995 Grade 5A (UNS J93404)
Inconel X750
PEEK
0C to 150C
Viton GLT
N/A
E6 E6R
VET-1012
single body double ball, compact valve
ASME B16.10
3" 6"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
600
A 352 Grade LCB
mono-block
needle valve integrated;
plug drain
trunnion
full bore
AISI 304
Inconel X750
Devlon V
-46C to 150C
Viton GLT
N/A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
162
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
Drilling/finishing
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
F6 F6R
VET-1013
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
900
A 352 Grade LCB
mono-block
needle valve integrated;
plug drain
trunnion
full bore
AISI 304
Inconel X750
Devlon V
-46C to 150C
Viton GLT
N/A
G6 G6R G19
VET-1014
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
1500
A 352 Grade LCB
mono-block
needle valve integrated;
plug drain
trunnion
full bore
AISI 304
Inconel X750
PEEK
-46C to 150C
Viton GLT
N/A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
163
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
Drilling/finishing
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
H3
VET-1015
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
2500
A 351 Grade CF8M
mono-block
needle valve integrated;
plug drain
trunnion
full bore
AISI 316
Inconel X750
PEEK
-46C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using
air or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); locking
device; anti-static device
manufacturer standard
100% visually casting according MSS
SP-55;
dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
H10
VET-1016
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
2500
A 216 Grade WCB
mono-block
needle valve integrated;
plug drain
trunnion
full bore
AISI 410
Inconel X750
PEEK
-29C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using
air or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); locking
device; anti-static device
manufacturer standard
100% visually casting according MSS
SP-55;
dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
164
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
Drilling/finishing
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes:
H10P
VET-1016P
single body double ball, compact valve
ASME B16.10 piggable
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
2500
A 216 Grade WCB
mono-block
needle valve integrated;
plug drain
trunnion
piggable - internal diameter (ID) valve
shall be
defined by Project Engineer
AISI 410
Inconel X750
PEEK
-29C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using
air or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); locking
device; anti-static device
manufacturer standard
100% visually casting according MSS
SP-55;
dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
H30
VET-1018
single body double ball, compact valve
ASME B16.10
2" 8"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
ASME B16.5;
ring type joint (RTJ)
2500
A 216 Grade WCB
mono-block
needle valve integrated;
plug drain
trunnion
full bore
AISI 410
Inconel X750
PEEK
-29C to 150C
N/A
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using
air or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
double piston effect (DPE); locking
device; anti-static device
manufacturer standard
100% visually casting according MSS
SP-55;
dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
165
of
193
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
B3
VET-1302
single body, double ball compact valve;
non standard
10" - 12"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 raised face (RF)
150
ASTM A 351 CF8M
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
ASTM A 351 CF8M
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
Lip Seal (PTFE + Elgiloy)
A 182 Gr F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using
air or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;flange
coupling operator according ISO 5208
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
C3
VET-1304
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 raised face (RF)
300
ASTM A 351 CF8M
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
ASTM A 351 CF8M
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
PTFE + Elgiloy
A 182 Gr F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using
air or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;flange
coupling operator according ISO 5208
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
166
of
193
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
E3
VET-1306
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
600
ASTM A 351 CF8M
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
ASTM A 351 CF8M
Inconel X750
Devlon V
-46C to 150C
Lip Seal (PTFE + Elgiloy)
A 182 Gr F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;flange
coupling operator according ISO 5208
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
F3
VET-1309
single body, double ball compact valve;
non standard
10" - 12"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
900
ASTM A 351 CF8M
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
ASTM A 351 CF8M
Inconel X750
PEEK
-46C to 150C
Lip Seal (PTFE + Elgiloy)
A 182 Gr F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;flange
coupling operator according ISO 5208
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
167
of
193
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
G3
VET-1311
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
1500
ASTM A 351 CF8M
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
ASTM A 351 CF8M
Inconel X750
PEEK
-46C to 150C
Lip Seal (PTFE + Elgiloy)
A 182 Gr F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;flange
coupling operator according ISO 5208
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
B16
VET-1313
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 raised face (RF)
150
A 995 Grade 4A (UNS J92205)
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
A 995 Grade 4A (UNS J92205)
Inconel X750
PTFE reinforced + 25% carbon
-46C to 150C
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
168
of
193
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
C16
VET-1315
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 raised face (RF)
300
A 995 Grade 4A (UNS J92205)
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
A 995 Grade 4A (UNS J92205)
Inconel X750
PTFE reinforced + 25% carbon
-46C to 150C
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; torque/thrust functional testing;
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
E16
VET-1317
single body, double ball compact valve;
non standard
10" - 12"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
600
A 995 Grade 4A (UNS J92205)
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
A 995 Grade 4A (UNS J92205)
Inconel X750
Devlon
-46C to 150C
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
TECHNICAL SPECIFICATION
E&P
N:
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
G16
VET-1322
single body, double ball compact
valve; non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
1500
A 995 Grade 4A (UNS J92205)
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
A 995 Grade 4A (UNS J92205)
Inconel X750
PEEK
-46C to 150C
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or
nitrogen as the test medium; lowpressure gas seat testing of 5.5 bar
0.7 bar using air or nitrogen as the test
medium; anti-static testing;
torque/thrust functional testing; cavity
relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined
parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
DR-ENGP-1.1
SHEET:
169
of
193
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
170
of
193
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
G16P
VET-1322P
single body, double ball compact valve;
non standard
10" - 12"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
1500
A 995 Grade 4A (UNS J92205)
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
piggable - internal diameter (ID) valve
shall be
defined by Project Engineer
A 995 Grade 4A (UNS J92205)
Inconel X750
PEEK
-46C to 150C
PTFE + Elgiloy
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D) (7)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
B6 B19
VET-1324
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 raised face (RF)
150
A 352 Gr LCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 304
Inconel X750
PTFE reinforced + 25% carbon
-46C to 150C
Lip Seal (PTFE + Elgiloy)
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
171
of
193
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
B9 B10
VET-1325
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 raised face (RF)
150
A 216 Grade WCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced + 25% carbon
-29C to 150C
Viton GLT
AISI 410
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
B4
VET-1326
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 raised face (RF)
150
A 216 Grade WCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced + 25% carbon
-29C to 210C
Viton GLT
AISI 410
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
172
of
193
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
C6
VET-1328
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 raised face (RF)
300
A 352 Gr LCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 304
Inconel X750
PTFE reinforced + 25% carbon
-46C to 150C
Lip Seal (PTFE + Elgiloy)
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
C9 C10
VET-1329
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 raised face (RF)
300
A 216 Grade WCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced + 25% carbon
-29C to 150C
Viton GLT
AISI 410
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
173
of
193
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
C4
VET-1330
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 raised face (RF)
300
A 216 Grade WCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 410
Inconel X750
PTFE reinforced + 25% carbon
-29C to 150C
Viton GLT
AISI 410
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
E6 E6R
VET-1332
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
600
A 352 Gr LCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 304
Inconel X750
Devlon V
-46C to 150C
Lip Seal (PTFE + Elgiloy)
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D) (7)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
174
of
193
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
E10
VET-1333P
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
600
A 216 Grade WCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 410
Inconel X750
Devlon V
0C to 150C
Viton B (5)
AISI 410
E9 E10 E17
VET-1333
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
600
A 216 Grade WCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 410
Inconel X750
Devlon V
-29C to 150C
Viton GLT (5)
-
AISI 410
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D) (7)
low-pressure gas seat testing between
according ISO 14313 (API 6D) (6) low- 0.5 bar and 1.0 bar using air or nitrogen
pressure gas seat testing of 5.5 bar
as the test medium; low-pressure gas
0.7 bar using air or nitrogen as the test seat testing of 5.5 bar 0.7 bar using air
medium; anti-static testing; torque/thrust or nitrogen as the test medium; antifunctional testing; cavity relief testing
static testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
according MSS SP-25
locking device; anti-static device;
locking device; anti-static device;
Manufacturer standard
Manufacturer standard
100% visually casting according MSS
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
1 - it shall be according ASME B16.34
and ASME section VIII standard
and ASME section VIII standard
2 - All valve components shall be fire
2 - All valve components shall be fire
tested
tested
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D) (7)
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
175
of
193
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
E4
VET-1334
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
600
A 216 Grade WCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 410
Inconel X750
Devlon V
-29C to 210C
Viton GLT (5)
AISI 410
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D) (7)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
F6 F6R
VET-1337
single body, double ball compact valve;
non standard
10" - 12"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
900
A 352 Gr LCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 304
Inconel X750
PEEK
-46C to 150C
Lip Seal (PTFE + Elgiloy)
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D) (7)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
176
of
193
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
G10 G10R
VET-1342
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
1500
A 216 Grade WCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 410
Inconel X750
PEEK
-29C to 150C
Viton GLT (5)
AISI 410
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D) (7)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
177
of
193
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
G10P
VET-1342P
single body, double ball compact valve;
non standard
10" - 14"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
1500
A 216 Grade WCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
piggable - internal diameter (ID) valve
shall be
defined by Project Engineer
AISI 410
Inconel X750
PEEK
-29C to 150C
Viton GLT (5)
AISI 410
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D) (7)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
H10 H14
VET-1343
single body, double ball compact valve;
non standard
10" - 12"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
2500
A 216 Grade WCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 410
Inconel X750
PEEK
-29C to 150C
Viton GLT (5)
AISI 410
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D) (7)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
178
of
193
TITLE:
APPENDIX 14
Spec
Feature
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat:
Seat insert:
Temperature:
O'ring:
Lip seal:
Stem/trunnion
material:
Stem:
Material Pad:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test:
Notes
G6 G6R G19
VET-1345
single body, double ball compact valve;
non standard
10" - 12"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
1500
A 352 Gr LCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 304
Inconel X750
PEEK
-46C to 150C
Lip Seal (PTFE + Elgiloy)
A 182 Grade F 316
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D) (7)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
H14
VET-1351
single body, double ball compact valve;
non standard
10" - 12"
ISO 14313 (1);
fire tested ISO 10497 (2); monogram
API
ASME B16.5 ring type joint (RTJ)
2500
A 216 Grade WCB
mono-block
valves with double ball and needle ISO
14313 (API 6D) valve integrated / plug
drain
trunnion
full bore
AISI 410
Inconel X750
PEEK
-29C to 150C
Viton GLT (5)
AISI 410
blow out proof stem, double seal
DU
handwheel gear operator
according ISO 14313 (API 6D) (7)
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antistatic testing; torque/thrust functional
testing; cavity relief testing
according MSS SP-25
locking device; anti-static device;
Manufacturer standard
100% visually casting according MSS
SP-55;Dye-penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
179
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test :
Notes
E3
VET-1400
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
800
A 182 Grade F 316
single body
Needle valve integrated
floating
full bore
A 182 Grade F 316
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
PTFE
N/A
A 182 Grade F 316
E6 E6R
VET-1401
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
800
ASTM A 105
single body
combined drain and vent
floating
full bore
ASTM A 105
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
PTFE
N/A
ASTM A 105
blow out proof stem, double seal
blow out proof stem, double seal
N/A
N/A
wrench (lever) operator
wrench (lever) operator
according ISO 14313 (API 6D)
according ISO 14313 (API 6D)
low-pressure gas seat testing between
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen 0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antior nitrogen as the test medium; antistatic testing; torque/thrust functional
static testing; torque/thrust functional
testing; cavity relief testing
testing; cavity relief testing
according MSS SP-25
according MSS SP-25
locking device; anti-static device
locking device; anti-static device
manufacturer standard
manufacturer standard
dye penetrant in machined parts
dye penetrant in machined parts
1 - it shall be according ASME B16.34
1 - it shall be according ASME B16.34
and ASME section VIII standard
and ASME section VIII standard
2 - All valve components shall be fire
2 - All valve components shall be fire
tested
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
180
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test :
Notes
E11 E30
VET-1402
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
800
Inconel 625
single body
combined drain and vent
floating
full bore
Inconel 625
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
PTFE
N/A
Inconel 625
E14
VET-1403
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
800
ASTM A 105
single body
combined drain and vent
floating
full bore
ASTM A105
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
PTFE
N/A
ASTM A105
blow out proof stem, double seal
blow out proof stem, double seal
N/A
N/A
wrench (lever) operator
wrench (lever) operator
according ISO 14313 (API 6D)
according ISO 14313 (API 6D)
low-pressure gas seat testing between
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen 0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antior nitrogen as the test medium; antistatic testing; torque/thrust functional
static testing; torque/thrust functional
testing; cavity relief testing
testing; cavity relief testing
according MSS SP-25
according MSS SP-25
locking device; anti-static device
locking device; anti-static device
manufacturer standard
manufacturer standard
dye penetrant in machined parts
dye penetrant in machined parts
1 - it shall be according ASME B16.34
1 - it shall be according ASME B16.34
and ASME section VIII standard
and ASME section VIII standard
2 - All valve components shall be fire
2 - All valve components shall be fire
tested
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
181
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test :
Notes
E11 E30
VET-1402
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
800
Inconel 625
single body
combined drain and vent
floating
full bore
Inconel 625
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
PTFE
N/A
Inconel 625
E14
VET-1403
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
800
ASTM A 105
single body
combined drain and vent
floating
full bore
ASTM A105
Inconel X750
PTFE reinforced with 25% of carbon
-29C to 150C
PTFE
N/A
ASTM A105
blow out proof stem, double seal
blow out proof stem, double seal
N/A
N/A
wrench (lever) operator
wrench (lever) operator
according ISO 14313 (API 6D)
according ISO 14313 (API 6D)
low-pressure gas seat testing between
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen 0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antior nitrogen as the test medium; antistatic testing; torque/thrust functional
static testing; torque/thrust functional
testing; cavity relief testing
testing; cavity relief testing
according MSS SP-25
according MSS SP-25
locking device; anti-static device
locking device; anti-static device
manufacturer standard
manufacturer standard
dye penetrant in machined parts
dye penetrant in machined parts
1 - it shall be according ASME B16.34
1 - it shall be according ASME B16.34
and ASME section VIII standard
and ASME section VIII standard
2 - All valve components shall be fire
2 - All valve components shall be fire
tested
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
182
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test :
Notes
F11 G11
VET-1408
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
1500
Inconel 625
single body
combined drain and vent
floating
full bore
INCONEL 625
Inconel X750
PEEK
-29C to 150C
PTFE
N/A
Inconel 625
blow out proof stem, double seal
blow out proof stem, double seal
N/A
N/A
wrench (lever) operator
wrench (lever) operator
according ISO 14313 (API 6D)
according ISO 14313 (API 6D)
low-pressure gas seat testing between
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen 0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antior nitrogen as the test medium; antistatic testing; torque/thrust functional
static testing; torque/thrust functional
testing; cavity relief testing
testing; cavity relief testing
according MSS SP-25
according MSS SP-25
locking device; anti-static device
locking device; anti-static device
manufacturer standard
manufacturer standard
dye penetrant in machined parts
dye penetrant in machined parts
1 - it shall be according ASME B16.34
1 - it shall be according ASME B16.34
and ASME section VIII standard
and ASME section VIII standard
2 - All valve components shall be fire
2 - All valve components shall be fire
tested
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
183
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test :
Notes
F14 G14
VET-1409
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
1500
ASTM A 105
single body
combined drain and vent
floating
full bore
ASTM A105
Inconel X750
PEEK
-29C to 150C
PTFE
N/A
ASTM A105
G12 G12P
VET-1410
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
1500
A 182 Grade F 55 (UNS S32760)
single body
combined drain and vent
floating
full bore
A 182 Grade F 55 (UNS S32760)
Inconel X750
PEEK
-46C to 150C
PTFE
N/A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
184
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test :
Notes
G19
VET-1412
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
1500
ASTM A 105
single body
combined drain and vent
floating
full bore
ASTM A105
Inconel X750
PEEK
-46C to 150C
PTFE
N/A
ASTM A105
H3
VET-1413
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
2500
A 182 Grade F 316
single body
combined drain and vent
floating
full bore
A 182 Gr F 316
Inconel X750
PEEK
-46C to 150C
PTFE
N/A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
185
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test :
Notes
H10 H10P
VET-1414
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
2500
ASTM A 105
single body
combined drain and vent
floating
full bore
ASTM A 105
Inconel X750
PEEK
-29C to 150C
PTFE
N/A
ASTM A 105
Inconel 625
blow out proof stem, double seal
blow out proof stem, double seal
N/A
N/A
wrench (lever) operator
wrench (lever) operator
according ISO 14313 (API 6D)
according ISO 14313 (API 6D)
low-pressure gas seat testing between
low-pressure gas seat testing between
0.5 bar and 1.0 bar using air or nitrogen 0.5 bar and 1.0 bar using air or nitrogen
as the test medium; low-pressure gas
as the test medium; low-pressure gas
seat testing of 5.5 bar 0.7 bar using air seat testing of 5.5 bar 0.7 bar using air
or nitrogen as the test medium; antior nitrogen as the test medium; antistatic testing; torque/thrust functional
static testing; torque/thrust functional
testing; cavity relief testing
testing; cavity relief testing
according MSS SP-25
according MSS SP-25
locking device; anti-static device
locking device; anti-static device
manufacturer standard
manufacturer standard
dye penetrant in machined parts
dye penetrant in machined parts
1 - it shall be according ASME B16.34
1 - it shall be according ASME B16.34
and ASME section VIII standard
and ASME section VIII standard
2 - All valve components shall be fire
2 - All valve components shall be fire
tested
tested
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
186
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test :
Notes
H14
VET-1416
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
2500
ASTM A 105
single body
combined drain and vent
floating
full bore
ASTM A105
Inconel X750
PEEK
-29C to 150C
PTFE
N/A
ASTM A105
E16
VET-1430
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
800
A 182 Grade F 51 (UNS S31803)
single body
combined drain and vent
floating
full bore
A 182 Grade F 51 (UNS S31803)
Inconel X750
PTFE reinforced with 25% of carbon
-46C to 150C
PTFE
N/A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
187
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Body type:
Vent/drain:
Ball mounting:
Bore type:
Obturator (ball):
Spring seat
Seat insert:
Temperature:
Orings seal:
Lip seal:
Stem/trunnion
material:
Stem:
Bushing:
Operator:
Test:
Test complement
according ISO 14313
(API 6D):
Marking:
General requirement:
Bolt/nut:
Test :
Notes
G16 G16P
VET-1432
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
1500
A 182 Grade F 51 (UNS S31803)
single body
combined drain and vent
floating
full bore
A 182 Grade F 51 (UNS S31803)
Inconel X750
PEEK
-46C to 150C
PTFE
N/A
A 182 Grade F 51 (UNS S31803)
E9 E10 E17
VET-1433
Single body floating double ball valve
1/2" 2"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
API
flange ASME B16.5; ring type joint
(RTJ) x screw
600
A 182 Grade F 51 (UNS S31803)
single body
combined drain and vent
floating
full bore
A 182 Grade F 51 (UNS S31803)
Inconel X750
PEEK
-46C to 150C
PTFE
N/A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
188
of
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Bore type:
Obturator (Disc):
Spring:
Seat:
Temperature:
Test:
Marking:
General requirement:
Bolt/nut:
E10
VET-1500
Non slam check valve
12" - 24"
ASME B16.34
fire tested ISO 10497
flange ASME B16.5; ring type joint
(RTJ)
600
A 216 Grade WCB
flow diffuser
A 182 Grade F 316
Inconel X750
metal to metal
0C to 210C
according API 6D;
API 598
according MSS SP-25
N/A
manufacturer standard
G10
VET-1502
Non slam check valve
4" - 10"
ASME B16.34
fire tested ISO 10497
flange ASME B16.5; ring type joint
(RTJ)
1500
A 216 Grade WCB
flow diffuser
A 182 Grade F 316
Inconel X750
metal to metal
0C to 210C
according API 6D;
API 598
according MSS SP-25
N/A
manufacturer standard
193
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
189
of
193
TITLE:
APPENDIX 14
Spec
Tag
Marking:
H10
VET-1503
Non slam check valve
4" - 10"
ASME B16.34
fire tested ISO 10497
flange ASME B16.5; ring type joint
(RTJ)
2500
A 216 Grade WCB
flow diffuser
A 182 Grade F 316
Inconel X750
metal to metal
0C to 210C
according API 6D;
API 598
according MSS SP-25
General requirement:
N/A
Bolt/nut:
manufacturer standard
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Bore type:
Obturator (Disc):
Spring:
Seat:
Temperature:
Test:
J31
VET-1504
Non slam check valve
4" - 8"
ASME B16.34
fire tested ISO 10497
compact flange NORSOK L-005; seal
type IX (MSJ)
10000 psi
A 522 type II
flow diffuser
A 522 type II
Inconel X750
metal to metal
-70C to 123C
according API 6D;
API 598
according API SPEC 6A
complying annex F API SPEC 6A
class P + U
manufacturer standard
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
190
of
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End/finishing:
Class:
Body material:
Bore type:
Obturator (Disc):
Spring:
Seat:
Temperature:
Test:
Marking:
General requirement:
Bolt/nut:
B22 B23
VET-1505
Non slam check valve
4" - 10"
ASME B16.34
fire tested ISO 10497
flange ASME B16.5; raised face (RF)
150
A 995 Grade 5A (UNS J93404)
flow diffuser
A 995 Grade 5A (UNS J93404)
Inconel X750
metal to metal
0C to 90C
according API 6D;
API 598
according MSS SP-25
N/A
manufacturer standard
B22 B23
VET-1506
Non slam check valve
12" - 48"
ASME B16.34
fire tested ISO 10497
flange ASME B16.5; raised face (RF)
150
A 995 Grade 5A (UNS J93404)
flow diffuser
A 995 Grade 5A (UNS J93404)
Inconel X750
metal to metal
0C to 90C
according API 6D;
API 598
according MSS SP-25
N/A
manufacturer standard
193
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
191
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End:
Working pressure
Body material:
Vent/drain:
Bore type:
Trim:
Seat:
Temperature:
Seals:
Stem packing:
Stem:
Stem material:
Operator:
Test:
Marking:
General requirement:
Bolt/nut:
Notes:
J31
VET-1600
Gate valve
1/2" 1 1/2"
API SPEC 6A (1)
fire tested API 6FA; monogram API (2)
compact flange according NORSOK L005
10000 psi
ASTM A 522 type II
combined drain and vent
full bore
ASTM A 522 type II
metal to metal + tungsten carbide
-70C to 123C
PTFE + Elgiloy + PEEK
PTFE + Elgiloy + PEEK
ball screw with blow out proof stem
17-4PH
non rising handwheel
API SPEC 6A;
PSL 3G
API SPEC 6A
complying annex F API SPEC 6A;
class K + U
manufacturer standard
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
J31
VET-1601
Gate valve
2" 14"
API SPEC 6A (1)
fire tested API 6FA; monogram API (2)
compact flange according NORSOK L005
10000 psi
ASTM A 522 type II
vent / drain plug in the cavity
full bore
ASTM A 522 type II
metal to metal + tungsten carbide
-70C to 123C
PTFE + Elgiloy + PEEK
PTFE + Elgiloy + PEEK
ball screw with blow out proof stem
17-4PH
non rising handwheel
API SPEC 6A;
PSL 3G
API SPEC 6A
complying annex F API SPEC 6A;
class K + U
manufacturer standard
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
test
TECHNICAL SPECIFICATION
E&P
N:
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Standard:
Certificate:
End:
Working pressure
Body material:
Vent/drain:
Bore type:
Trim:
Seat:
Temperature:
Seals:
Stem packing:
Stem:
Stem material:
Operator:
Test:
Marking:
General requirement:
Bolt/nut:
Notes:
J31P
VET-1601P
Gate valve
4" 8"
API SPEC 6A (1)
fire tested API 6FA; monogram API (2)
compact flange according NORSOK L005
10000 psi
ASTM A 522 type II
vent / drain plug in the cavity
piggable - internal diameter (ID) valve
shall be
defined by Project Engineer
ASTM A 522 type II
metal to metal + tungsten carbide
-70C to 123C
PTFE + Elgiloy + PEEK
PTFE + Elgiloy + PEEK
ball screw with blow out proof stem
17-4PH
non rising handwheel
API SPEC 6A;
PSL 3G
API SPEC 6A
complying annex F API SPEC 6A;
class K + U
manufacturer standard
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire test
DR-ENGP-1.1
SHEET:
192
of
193
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
193
of
193
TITLE:
APPENDIX 14
Spec
Tag
Type:
NPS:
Reference standard:
Certificate:
End/finishing:
Class:
Body material:
Bore type:
Obturator (trim):
Seat insert:
Temperature:
Lip seal:
Stem material:
Stem:
Test:
Marking:
General requirement:
Bolt/nut:
Test:
Note:
H30
VET-1700
Axial control valve
6" - 12"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2)
flange ASME B16.5; ring type joint
(RTJ)
2500
A 995 Grade 4A (UNS J92205)
axial control flow
A 995 Grade 4A (UNS J92205)
PEEK
-29C to 100C
PTFE + Elgiloy
17-4PH (UNS S17400)
blow out proof stem, double seal (3)
according ISO 14313 (API 6D) (4)
according MSS SP-25
locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
3 - System for automatic detection of
loss of sealing stem seal
4 - Critteria approval is zero leakage,
according ISO 5208, "rate A"
H30
VET-1701
Axial control valve
14" - 20"
ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2)
compact flange according NORSOK L005
2500
A 995 Grade 4A (UNS J92205)
axial control flow
A 995 Grade 4A (UNS J92205)
PEEK
-29C to 100C
PTFE + Elgiloy
17-4PH (UNS S17400)
blow out proof stem, double seal (3)
according ISO 14313 (API 6D) (4)
according MSS SP-25
locking device; anti-static device
manufacturer standard
100% visual casting according MSS SP55; dye penetrant in machined parts
1 - it shall be according ASME B16.34
and ASME section VIII standard
2 - All valve components shall be fire
tested
3 - System for automatic detection of
loss of sealing stem seal
4 - Critteria approval is zero leakage,
according ISO 5208, "rate A"
N:
TECHNICAL SPECIFICATION
I-ET-3000.00-1200-200-PCI-001
CLIENT:
SHEET:
1 of
3
E&P
PROGRAM:
PIPING MATERIAL - STANDARDIZATION
REA:
ET-200.03
E&P - ENGP
TITLE:
APPENDIX 15
Isolating Joint
4
3
2
1
ITEM
Isolating joint
Fenolic resin coated with neoprene
Lock washer
Carbon steel
Isolating lock washer
Phenolic resin
Isolating bushing
Polyethylene
DESCRIPTION
MATERIAL
CIRCULAR ISOLATING JOINT
FLAT RING TYPE
REV. 0
Date
Project
Execution
Verification
Approval
REV. A
REV. B
REV. C
REV. D
REV. E
Sep/04
E&P
See sheet 2
Hernon
Thomaz
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORM N-381 REV. F
REV. F
REV. G
REV. H
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-002
SHEET:
2
TITLE:
APPENDIX 15
Isolating Joint
4
3
2
1
ITEM
Isolating joint
Fenolic resin coated with neoprene
Lock washer
Carbon steel
Isolating lock washer
Phenolic resin
Isolating bushing
Polyethylene
DESCRIPTION
MATERIAL
CIRCULAR ISOLATING JOINT
FLAT FACE TYPE
REV.
of
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-002
SHEET:
3
TITLE:
APPENDIX 15
Isolating Joint
4
3
2
1
ITEM
Isolating joint
Fenolic resin coated with neoprene
Lock washer
Carbon steel
Isolating lock washer
Phenolic resin
Isolating bushing
Polyethylene
DESCRIPTION
MATERIAL
CIRCULAR ISOLATING JOINT
OVAL TYPE
REV.
of
N:
TECHNICAL SPECIFICATION
I-ET-3000.00-1200-200-PCI-001
CLIENT:
SHEET:
1 of
2
E&P
PROGRAM:
PIPING MATERIAL - STANDARDIZATION
AREA:
ET-200.03
E&P - ENGP
TITLE:
APPENDIX 16
Min.
Tension
UNS
S32760
UNS
S32750
UNS
S31803
UNS
S32205
N of tests
100% welded
100% top welds
100% of welded areas
Charpy V (-46C)
(6mm thickness &
greater) or minimum
temperature of
project
ASME IX
L. resistance 620 Mpa
3 CPs each
weld metal (MS)
fusion line (LF)
REV. 0
Project
Execution
Verification
Approval
REV. A
REV. B
ASME IX
ASME IX
Date
Acceptance
ASME IX
ASME IX
ASME VIII div 1 app 8
L. resistance 750 Mpa
2 faces + 2 roots, or 4
lateral folds
Folding
Standard
ASME IX
ASME IX
ASME VIII div.1
app 8
REV. C
ASTM E 562
35% - 55%
REV. D
REV. F
REV. E
Sep/04
Nov/05
Nov/06
Sep/09
E&P
E&P
E&P
E&P
See sheet 2 See sheet 2 See sheet 2 Ney Robson
Hernon
Paiva
Paiva
Fernando
Thomaz
Joper
Joper
Cludio
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORM N-381 REV. F
REV. G
REV. H
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
2
REV.
of
TITLE:
APPENDIX 16
Welding Qualification for Duplex and Superduplex
Pitting Corrosion
ASTM G 48 A,
No pitting, 20X
24HRS, 40C (as Mass loss not
welded), only
exceeding 4.0 g/m2
superduplex
Max. Hardness 25 Cr
32 HRC or 330HV10
2mm from the surface
NORSOK M-601
Max. Hardness 22 Cr
28 HRC or 290HV10
OBS:
GTAW TIG WELDING Recommended on the root run.
SHIELDING GASES Argon (Ar) 2% N2 or mixture of Air and Helium (He).
The consumable's composition should contain between 2% and 3.5% Ni above of the base
metal.
2 WELDER QUALIFICATION
ASME IX With the following tests:
TEST
Visual
Radiography
Folding
Metallography
N of tests
100% of welded areas
100% top welds
2 faces+2 roots, or 4
sides
MS, ZTA, MB
Standard
ASME IX
ASME IX
ASME IX
Acceptance
ASME IX
ASME IX
ASME IX
NORSOK M 601
No precipitations 400X
N:
TECHNICAL SPECIFICATION
CLIENT:
E&P
PROGRAM:
SHEET:
OF
11
AREA:
ET-200.03
TITLE:
E&P - ENGP
I-ET-3000.00-1200-200-PCI-001
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
1 - OBJECTIVE
1.1 - This Appendix contains the minimum mandatory requirements for design,
production, inspection and acceptance of stainless steel duplex and
superduplex cast valves (UNS J92205, UNS J93404 and UNS J93380), made
using no bake sand foundry process, to be used in PETROBRAS Exploration
and Production Units.
1.2 This Appendix is applicable to ball, gate, globe and check type flanged valves,
as defined in the Specifications (Specs) B16, B12, B13, C16, C12, C13, E16,
G16, G16P, G12, G12P and J12.
1.3 This appendix is applicable for class 150 to 1500 and 10000 PSIG valves with
nominal diameter of 2 inches or higher.
2 - COMPLEMENTARY DOCUMENTS
2.1 The documents listed below are valid for the present appendix:
ASME B16.34 96
ASME SA 995 04
ASME SEC
APPENDIX 7
VIII
DIV
Date
Rev. 0
Rev. A
Rev. B
Nov/05
Jan/06
Sep/09
Project
E&P
E&P
E&P
Execution
Paiva
Paiva
Ney Robson
Verification
Fernando
Fernando
Fernando
Joper
Joper
Claudio
Approval
Rev. C
Rev. D
Rev. E
ALL INFORMATION HEREIN IS PROPERTY OF PETROBRAS, IT IS EXPRESSLY FORBIDEN TO USE FOR OTHER PURPOSES.
FORM BELONGING TO PETROBRAS NORMS REV. G
All
Methods
of
Qualifications
of
Requirements,
for
Rev. F
Rev. G
Rev. H
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
2
REV.
of
11
TITLE:
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
ASTM A 370 05
ASTM E 94 04
Radiograph Examination
ASTM E 165 02
ASTM E 186 98
ASTM E 280 98
ASTM E 446 98
ASTM E 562 02
ASTM E 1030 00
ASTM G 48 03
MSS SP-55-2001
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
3
REV.
of
11
TITLE:
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
3 - DEFINITIONS
3.1 PITTING RESISTANCE EQUIVALENT NUMBER (PREN): Empiric Mathematical
Formula that correlate resistance to localized corrosion, in environments
containing chlorides, with the amounts alloying elements in the steel that
contribute to increase this resistance. For the super-duplex steel the PREN 40.
PREN = %Cr + 3.3 x %Mo + 16 x %N.
3.1.1 PILOT CASTING: Any casting, that is the first of its model or of a new or
modified project, using the same casting procedure (same casting) as the ones it
represents.
3.1.2 CASTING: Any component of a valve.
4 - DOCUMENTATION
4.1 The Manual of each valve shall contain all the certificates related to each piece
that is part of the said valve. These certificates are related to:
-
chemical requirements;
4.2 The manual shall contain Welding Procedure Specifications (WPS) for defect
repairing, duly approved by PETROBRAS or by a Classification Society indicated
by PETROBRAS.
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
4
REV.
of
11
TITLE:
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
Cavity mapping for bigger repairs for each part of the valve and;
The Welding Registration Report (RRS) of the repairs of each part of the
valve.
5 - CHEMICAL REQUIREMENTS
5.1 The duplex steel composition used for the manufacturing of the cast valve shall
be in accordance with 4A degrees (UNS J92205 or CD3MN) of ASME SA-995 or
ASTM A 995 standards, to attend the Specifications of B16, C16, E16, G16 and
G16P.
5.2 - The superduplex steel composition used for the manufacturing of the cast valve
shall be in accordance with 5A degrees (UNS J93404 or CE3MN) of ASME SA995 or ASTM A 995 standards, to attend the Specifications of B12, C12, G12,
G12P and J12.
5.3 The superduplex steel composition used to manufacture the cast valves shall be
in accordance with the 6A degrees (UNS J93380 or CD3MWCuN) of the ASME
SA-995 or ASTM A 995 standards, to attend the Especs B13 and C13.
5.4 The representative sample of the chemical requirements of the valve shall be
collected from the pouring ladle.
5.5 A representative sample for carbon, sulfur and nitrogen contents shall be
collected from the furnace before pouring into the ladle.
5.6 The addition of Niobium to the cast shall be avoided. The maximum Niobium
content admitted shall be of 0.060% at the chemical requirements of the cast.
5.7 Adding Aluminum to the run shall be avoided. The maximum content of
Aluminum admitted to the final chemical requirements shall be of 0.030%.
5.8 The levels of Nitrogen shall preferably be in the range of 0.20 to 0.25% for the
two degrees subject of this Appendix.
5.9 All consumables for the welding process shall have certification of their chemical
requirements guaranteeing the Maximum levels of Niobium of 0.060%.
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
5
REV.
of
11
TITLE:
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
5.10 The chemical analysis of the elements shall be made in calibrated equipment
using certified standards.
5.11 When more than one ladle is used for one mold, the metal founded in each
ladle shall be in accordance with the chemical specifications for the required
level.
6 - HEAT TREATMENT
6.1 The procedure for solubilization heat treatment used to the superduplex steel for
the production of the cast valves shall be in accordance with the procedure for
heat treatment defined for 5A degrees (UNS J93404 or CE3MN) and 6A (UNS
J93380 or CD3MWCuN) of ASME SA-995 or ASTM A 995 standards.
6.2 Only solubilization heat treatment could be used in the production of the
superduplex steel no other heat treatment could be used to produce it.
6.3 The maximum number of solubilization heat treatments allowed for a single
valve is limited to three (03) at foundry and one (01) at machining shop. If more
heat treatments are needed, PETROBRAS shall be consulted for the
authorization of such additional heat treatments.
6.4 Not any valve shall be supplied as cast without solubilization heat treatments.
6.5 - All heat treatments shall be monitored through thermocouples in the heat
charge and in the furnace, generating a report shat shall be annexed to the
manual of the valve.
6.6 Not any repairs using welding shall be executed on the piece before its prior
submission to heat treatment.
6.7 When solubilization heat treatment is necessary after casting, it shall be
executed taking all the necessary precautions so as not to allow distortions of
the piece. This solubilization heat treatment is limited to a maximum acceptable
one (1) heat treatment defined in item 6.3.
6.8 The soaking time depends on the prior experience of the manufacturer, but shall
be so that guarantees full solubilization of the inter-metallic phases and the
precipitates through the thickest dimension of the piece without causing
dimensional distortions.
6.9 The Pilot Casting shall have the possibility of extracting a test specimen from
the body of the piece for metallographic tests, which can be in any direction
(longitudinal or transversal), representing a central session of the thickest part of
the piece, as in the supplementary pre-requisite S26.2 of ASTM A703 standard,
to verify the effectiveness and adjustment of the soaking time of the
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
6
REV.
of
11
TITLE:
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
solubilization heat treatment. The results of this metallographic shall be part of
the manual of each valve.
6.10 The result of the metallographic test shall indicate absence of inter-metallic
phases and undesired precipitates notably, the sigma phase, carbides and
nitrates in a 200X magnification, as well as indicate a level of ferrite in the
range of 35 to 55%, according to ASTM E 562 standard.
6.11 For each casting that weighs more than 300 kg, specimens for mechanical
and metallurgical tests shall be attached, as in ASTM A 703. These test
specimens shall remain attached to the casting until the last thermal treatment.
For pieces weighing less than 300 kg, a test specimen per run is accepted.
7 - MECHANICAL AND METALLURGICAL TESTS
7.1 The mechanical and metallurgical tests shall be done after the last the
solubilization heat treatment before machining the casting.
7.2 The mechanical tests to be executed are those of tension, hardness and impact
(Charpy-V). These tests shall be executed according to ASTM A 370 standard.
7.3 The test specimens shall be obtained from cast test blocks, as in ASTM A703.
These blocks shall go through all the solubilization heat treatments before
collecting the specimens for analysis.
7.4 - One (01) specimen shall be extracted for the tension test. The minimum
acceptable values are set in Table 1 (ASME SA-995 or ASTM A 995).
Grade
4A
5A
6A
UNS
J92205
J93404
J93380
25
18
65 [450] {46}
25
7.5 Three (03) test specimens shall be collected for the impact tests (Charpy-V).
The tests shall be run at a temperature of - 46oC. The minimum values of
absorbed energy shall be of 45J for an average of the three test specimens and
35J for each one of the test specimens.
7.6 The hardness tests shall be run on a test specimen collected from a test block,
in a point representative of the central part of the thickest part of the casting,
according to the supplementary requirement S26.2 of ASTM A703 standard, that
has direct contact with the process fluid. The maximum hardness shall not be
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
7
REV.
of
11
TITLE:
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
above 32 HRC (or 310 HB or 330 HV10), considering the average of three
measurements. Castings that are lighter than 300 kg shall be tested individually
and shall render specific hardness values less or equal to the Pilot Casting on
the surface.
7.7 A test specimen shall be collected from the Pilot Casting, to run the corrosion
tests according to ASTM G48 Method A. The test shall be run for 24 hours at a
temperature of 50oC. The acceptance criteria are just for 5A degrees (UNS
J93404 or CE3MN) and 6A degrees (UNS J93380 or CD3MWCuN):
-
7.8 The test to determine the levels of ferrite shall be run in accordance with ASTM
E 562. The test specimen to run this test shall be collected from a cast test block
connected to a casting, that would represent a certain run. The acceptable range
is 35 to 55% of ferrite.
8 - INSPECTION
8.1 VISUAL
8.1.1 The visual inspection shall be made on each casting before and after each
solubilization heat treatment, after pre-machining (whenever is the case) and
the final machining. All castings that make up the valves of the same
manufacturing order shall undergo visual inspection.
8.1.2 All accessible surfaces, internal and external, shall be visually examined,
comparing acceptable discontinuities and superficial finishing attending the
standards set by MSS SP-55 or comparison standards of Steel Casting
Research and Trading Association (SCRATA) adopted in ASTM A802, or
other standard considered equivalent by a set deal between the manufacturer
of the valve and PETROBRAS.
8.1.3 The levels of acceptance for visual inspections are set in ASTM A802, and
are:
-
8.1.4 All castings that present in one or more surfaces the following defects,
independent of how serious or how extensive the defect is, or weather it
allows repairs using welding or not, shall be considered UNACCEPTABLE:
-
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
8
REV.
of
11
TITLE:
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
-
Shut metal discontinuity due to the encounter of two currents of metal that
have not been well mixed;
Rat tail depression on the surface of the piece caused by waves or failure
in the mold surface;
Linear when the relation between length and width is bigger or equal to 3;
Non-linear when the relation between length and width is less than 3;
8.2.6 The criteria of acceptance by the inspection by penetrating liquids are shown
in ASME SEC VIII DIV 1 APPENDIX 7.
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
9
REV.
of
11
TITLE:
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
8.3 RADIOGRAPHY
8.3.1 The radiographic inspection shall be executed by Level 2 inspectors, qualified
by the Sistema de Nacional de Qualificao e Certificao (National System
of Qualification and Certification) in Non-Destructive Tests (SNQC/END), or by
another certification means considered equivalent by agreement between the
manufacturer of the valve and PETROBRAS.
8.3.2 The radiographic inspection shall be run on the Pilot Casting (body, cap and
shutter), after the final solubilization heat treatment. In case or pieces included
in classes 900, 1500 and 10000 PSIG, it is mandatory to radio graphically
inspect of 100% of the final pieces, in the critical regions defined in ASME
B16.34.
8.3.3 The radiographic inspection shall be executed accordingly with ASTM E 94
and ASTM E 1030 standards.
8.3.4 The parts to be radiographed and the criteria of acceptance shall be in
accordance with ASME B16.34.
8.3.5 If all indications were classified as ACCEPTABLE no other piece equal to the
Pilot Casting needs to be radiographed.
8.3.6 If one or more conditions were classified UNACCEPTABLE the Pilot Casting
shall be fixed or scrapped and another piece shall be radiographed. If the
second piece were approved, not any equal piece needs to be radiographed.
However, if the second piece also presented indications classified as
UNACCEPTABLE all pieces equal to the Pilot Casting of the order shall be
radiographed in the areas rejected for the Pilot Casting and for the second
casting. The second casting and the subsequent piece of the order shall be
repaired whenever possible.
Defects
Thickness < 2
4 Thickness < 12
Standards
ASTM E 446
ASTM E 446
ASTM E 186
Porosity (A)
A2
A3
A3
B3
B3
B3
CA2
CA3
CA3
CB3
CB3
CB3
CC3
CC3
CC3
CD3
Cracks (D)
None
None
None
None
None
None
Inserts (F)
None
None
None
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
10
REV.
of
11
TITLE:
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
9 - REPARES
9.1 - The reparations of the defects found in the various inspections shall be corrected
by welding.
9.2 - The reparations shall have a specific Welding Procedure Specification (WPS),
duley approved by PETROBRAS or by the Classification Society indicated by
PETROBRAS. This WPS shall be based on ASTM A 488.
9.3 - The WPS and the qualification of the welder shall follow the approval criteria set
in Appendix 16 of this specification.
9.4 - The execution of the repair job shall be accompanied by a Level I welding
inspector.
9.5 - The surface to be repaired shall be inspected visually and by penetrant liquid
and depending on the extension of the defect, by radiography, before submitting
it to the welding procedures.
9.6 - After welding, the repair shall be inspected visually and by penetrant liquid and
depending on the extension of the repair, by radiography. All the inspections
shall obey the same criteria of item 8.
9.7 - An obligatory solubilization heat treatment made when:
- The repair is executed after leaking in the hydrostatic test;
- The cavity after the preparation for the repairs were over 20% of the width or
25 mm whichever is smaller;
- The extension (area) of the cavity were bigger than 65 cm.
10 MACHINING
10.1 The machining of the casting shall only be executed after solubilization heat
treatment.
10.2 Because the superduplex steels have law machining, it becomes essential to
adopt some rules to avoid the getting new defects on the pieces. These rules
are:
-
The machining equipment shall be robust, with enough power and free from
vibrations;
The tool shall be kept sharp during all the machining process. Tools with a
not so sharp blade cause glazing and hardening of the surface of the steel.
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-001
SHEET:
11
REV.
of
11
TITLE:
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
The sharpening of the blade shall be made using an emery with a whole
uncontaminated grinder.
Even for small advances the depth of the grinding shall be that so that it
would remove the layer below the deformed layer in the run before the last
avoiding hardening of the surface material;
The angle of attack of the tool shall be so, that it avoids its friction on the
surface of the piece;
The cutting tool shall be big enough to help with heat dissipation;
The use of chip breaker shall be fit to direct the hard and long chips away
from the machining surface;
The constant advance is extremely important to avoid that the tool friction
the piece;
The use of adequate cooling fluid is essential, as well as the amount used.
This amount shall so, that it covers all cutting tool and the surface that is
being tooled/machined, allowing dispersal of the generated heat;
10.3 After machining, a visual inspection and one by penetrant liquids shall be
made. The defects and indications shall be treated similarly to item 8.
10.4 If repairs are needed, these shall be executed as described in item 9.
10.5 Repairs that require solubilization heat treatments shall take into
consideration the dimensional deformation. The heat treatment shall be
included as one of the three (03) authorized heat treatments when at foundry
and one (01) at machining shop, otherwise it shall be authorized by
PETROBRAS prior to execution.
N:
TECHNICAL SPECIFICATION
DR-ENGP-1.1
CLIENT:
SHEET:
1
E&P
PROGRAM:
PIPING MATERIAL - STANDARDIZATION
REA:
ET-200.03
E&P - ENGP
TITLE:
of
APPENDIX 18
Technical data of organic coated for piping and valves.
This appendix defines technical data of organic coating for piping and valves. The
manufacturer of valves shall be agreement with the applicator for supply. When used in
systems piping with produced water (PCW).
1 - The preparation of the metallic surface prior to application of the coating should be
at least Sa 2 1/2 (to the near white metal) in accordance with the standard ISO 8501-1.
2 - The selection coating will have to be made in agreement Table 1.
Table 1 Technical data of organic coated.
Product
name
Temperature
65C 90C 120C 150C
Applied form
Piping
ID Min ID Max L Max
Valves
Repar in the
field
Belzona 1522
___
Air less
3 in
12 m
___
Belzona 1391
___
___
Roll brush or
centrifugation
3 in
12 m
___
Belzona 1321
___
___
Roll brush or
centrifugation
3 in
12 m
___
Belzona 5891
___
___
Air less
3 in
12 m
___
0,5 in
0,75 in
0,3 m
1 in
1,5 in
2m
2 in
3 in
3m
4 in
6m
___
Foam pig
___
___
Air less
4 in
6m
___
___
Air less
4 in
6m
___
Nova Coating
IPC ME 35
0,5 in
1,5 in
1,5 m
___
Electrostatic
1,5 in
14 in
12 m
Nova Coating
IPC MAGNA
0,5 in
1,5 in
1,5 m
___
___
___
Airless or roll
brush
Hallar 9412
___
Electrostatic
Date
Project
Execution
Verification
Approval
___
Electrostatic
REV. 0
REV. A
REV. B
REV. C
May/06
E&P
Fernando
Hernon
Joper
Sep/09
E&P
Carlos
Fernando
Claudio
Sep/10
E&P
EISA
IPP
ENGP
Nov/10
E&P
EISA
IPP
ENGP
1,5 in
36 in
6m
4 in
6m
0,5 in
1 in
0,3 m
1,5 in
2 in
1m
2 in
24 in
14 in
0,5 in
1 in
0,3 m
1,5 in
2 in
1m
2 in
24 in
14 in
REV. D
REV. E
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORME N-381 REV. F
As recommended
by the
manufacturer.
___
As recommended
by the
manufacturer.
As recommended
by the
manufacturer.
Electrostatic
SaureInsen
Fibrecrete 218
Hallar
6614+6014
REV. F
REV. G
REV. H
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
TITLE:
APPENDIX 18
Technical data of organic coated for piping and valves.
Temperature
Product
name
DuPont XF
___
Scothkote 134
Ciapowder 401
___
___
Applied form
Electrostatic
Electrostatic
___
Electrostatic
Piping
ID Min ID Max L Max
0,5 in
1 in
0,3 m
1,5 in
2 in
1m
2 in
24 in
14 in
0,5 in
1 in
0,3 m
1,5 in
2 in
1m
2 in
24 in
14 in
0,5 in
1 in
0,3 m
1,5 in
36 in
6m
Valves
Repar in the
field
As recommended
by the
manufacturer.
As recommended
by the
manufacturer.
As recommended
by the
manufacturer.
Abreviations:
A=Applicable
ID=Internal Diameter
L=Lenght
Table 2 List of products and respective applicator.
Supply
Belzona
Product
1522
1391
1321
5891
ARC 855 HT
Material
Hita
Epoxy composite
MacSeal
Chesco do Brasil
Refrantec
Chesterton
Resinar
Sauereisen
Solvay-Solexis
3M
Jera
DuPont
Applicator
Vinyl ester
composite
Rust Engenharia
Epoxy composite
ECTFE
FBE
ECTFE
FBE
ECTFE
Fluoropolymer
Nova Coating
Metalcoating
K&S Lupatech
K&S Lupatech
-
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
TITLE:
APPENDIX 18
Technical data of organic coated for piping and valves.
3 - The organic coating should have thickness as Table 2.
Thickness (m)
Product name
1 cost
2 cost
3 cost
Final average
thickness
Belzona 1522
800
----
----
800
Belzona 1391
600
----
----
600
Belzona 1321
600
----
----
600
Belzona 5891
800
----
----
800
800
800
----
1600
200
----
----
200
600
----
----
400 - 500
40 (RM 40)
400
400
840
40 (RM 40G)
400
400
840
100
1000
250
1350
200
----
----
200
Chesterton ACR
855 HT
Nova Coating IPC ME
35
Nova Coating IPC
MAGNA
Resinar Flake Glass
500 EN
Resinar Flake Glass
500 N
Sauereisen Fibrecrete
218
Scothkote 134
Hallar 9414
600
----
----
400 - 500
600
----
----
400 - 500
Dupont XF
200
----
----
120
Ciapowder 401
600
----
----
400 - 500
5 - During the final inspection, first perform a visual check that there are no
discontinuities or projections along the entire surface of the organic coated, then
perform an inspection using a Holiday Detector with a 1,0 kV direct current. Its not
admissible any kind of discontinuities/sparks on the metallic surface.
N:
TECHNICAL SPECIFICATION
I-ET-3000.00-1200-200-PCI-001
CLIENT:
SHEET:
1 of
4
E&P
PROGRAM:
PIPING MATERIAL - STANDARDIZATION
REA:
ET-200.03
TTLE:
APPENDIX 19
E&P - ENGP
1 - Introduction
1.1 - This appendix defines the criterias of acceptance and minimum
requirements for buying, handling, storing and transport of non-metallic piping,
on production installations of PETROBRAS.
1.2 The materials covered by this appendix, are listed below:
PRFV Fiberglass reinforced plastic.
PVC Poly vinyl chloride.
CPVC Chlorinated poly vinyl chloride.
RPVC Reinforced chlorinated poly vinyl chloride.
1.3 This appendix applies to pipe systems for transport of water and aqueous
solutions.
2 Applicable Standards
ASTM F 1173 - Standard Specification for Thermosetting Resin Fiberglass
Piping Systems to be used for Marine Applications
IMO A 753 (18) - Guidelines for the application of plastic pipes on ships International Maritime Organization (resolution 18)
ISO 14692 - Petroleum and natural gas industries - Glass-reinforced plastics
(GRP) piping
3 General Specifications
3.1 The non-metallic piping cited in item 1.2 of this appendix, used on floating
marine instalations of production, shall attend the requirements of resolution
IMO A 753 (18).
Rev. 0
Datee
Project
Execution
Verification
Approval
Rev. A
Rev. B
Rev. C
Rev. D
Rev. E
Aug/06
E&P
See Fl 2
Fernando
Joper
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORME N-381 REV. F
Rev. F
Rev. G
Rev. H
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-002
SHEET:
2
REV.
of
TTLE:
APPENDIX 19
3.2 The draftsman shall check the possibility of water hammer occurrence. If
positive, offer a revision of conducting the pipe to attenuate it, as well as, use
preferencially butterfly or gate valve.
3.3 - During project and assembly, the inspection of PETROBRAS shall check
the accomplishment to calculation of flexibility and supporting provided by the
draftsman.
3.4 The overhead pipes, fittings and flanges in PRFV and RPVC shall have an
external layer of improved resin with ultraviolet inhibitor and also be painted
each 2 (two) years when exposed to ultraviolet light effects.
3.5 At new projects, pipes, fittings and flanges made on PRFV according
ASTM F1173 or on RPVC, shall be prepared by the same supplier. On cases of
extension or repair, shall be inspected the compatibility between the available
suppliers.
3.6 The non-metallic piping shall have minimum internal roughness coefficient
of 140 Hazen-Williams.
3.7 - Pipes, fittings and flanges in PRFV and RPVC shall have wall thickness
calculated by supplier.
3.8 The flanged fittings shall be made using a torquimeter, according values
and sequence of tightness provided by the supplier.
3.9 Plain washers shall be used on flanged fittings, in order to allow a better
distribution of stress.
3.10 During the assembly, the PETROBRAS inspection shall attest that the
alignement and paralellism tolerances attend the specifications of supplier.
3.11 Valves or other heavy equipments conected to piping, shall be supported
apart the rest of piping.
3.14 The lamination kit and the application procedure shall be purchased by
the same piping supplier.
4 - Constructive Caracteristics
4.1 - PRFV
4.1.1 Supplier shall be responsible by the project (FEED, flexibility and
supporting), fabricao, assembly, maintenance, commissioning, inspection and
piping tests.
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-002
SHEET:
3
REV.
of
TTLE:
APPENDIX 19
4.3 - RPVC
4.3.1 The junction of liner shall be made using weld with a PVC rod.
4.3.2 The preparation of the terminations to lamination (machined) shall be
made using sanding machine.
4.3.3 During the process of junction, the disarrange between terminations shall
be corrected, in order to assure the continuity and integrity of the liner
(chemical fence).
5 - Inspection
A visual inspection shall be made on the acceptance of material, before
mounting on field.
TECHNICAL SPECIFICATION
E&P
N:
I-ET-3000.00-1200-200-PCI-002
SHEET:
4
REV.
of
TTLE:
APPENDIX 19
For pipes, fittings and accessories made in PRFV, the visual inspection shall
attend criterias of ASTM F 1173.
Technical Specification
CLIENTE:
N:
E&P
PROGRAMA:
ET-3000.00-1200-200-PCI-001
FOLHA:
1 de 17
REA:
ET-200.03
TTULO:
APPENDIX 20
E&P - ENGP
NDICE
1. Objective ________________________________________________________ 3
2. Reference Documents ______________________________________________ 3
3. Definitons _________________________________________________________3
4. General Requirements _______________________________________________3
5. Specific Requirements for Fully Tight Valves (VET) _________________________5
6. Functional Pressure Tests ____________________________________________11
7. Pos-Test Activities __________________________________________________13
8. Receiving Inspection ________________________________________________18
9. Storage __________________________________________________________18
10. Recommendations about VET Installation ______________________________18
Original
Data
Projeto
Execuo
Verificao
Aprovao
Out/07
E&P
Ver Fl. 2
Hernon
Cludio
AS INFORMAES DESTE DOCUMENTO SO PROPRIEDADE DA PETROBRAS, SENDO PROIBIDA A UTILIZAO FORA DA SUA FINALIDADE.
FORMULRIO PERTENCENTE NORMA PETROBRAS N-381 REV. G
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
2
REV.
de
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
NAME:
Hernon Viana Filho
Fernando Costa
Dlio Rodrigues da Silva
Milton Correa
Gerson C. Lima
Carlos Roberto Firmino
DEPARTMENT/SECTOR:
E&P ENGP/IPMI/EISA (Coordenador)
E&P ENGP/IPMI/EISA
E&P ENGP/IPMI/EISA
UN-RIO/ST/EISA
UN-BC/ENGP/EIS
E&P ENGP/IPMI/EISA
KEY:
K0M8
K074
W0H4
FMC0
QM27
EPCH
COLLABORATORS
NAME:
Allan Gaban
DEPARTMENT/SECTOR:
E&P ENGP/IPMI/EISA
KEY:
UVF7
17
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
3
REV.
de
17
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
1. OBJECTIVE
Define the requirements for receiving activities (inspection, tests, packaging, storage
and preservation) of industrial valves (VETs and conventional) in E&P, establishing
minimum requirements to be met throughout the supply cycle, either in cases of
acquired valves by third parties for use in new industrial units (typical EPCista cases)
or in the case of acquired valves by UNs for assembly and maintenance of existing
facilities or new facilities.
2. REFERENCE DOCUMENTS
API Standard 6D Valve Inspection and Testing, 22th Edition, January 2002
API Standard 598 Valve Inspection and Testing, 8th Edition, May 2004
API Standard 609 Butterfly Valves: Double Flanged, Lug- and Wafer-Type,
6thEdition, May 2004
ANSI B 16.34 Valve Flanged, Threaded, and Welding End
ET-3000.00-1200-956-PCI-001-Rev.0 - Cdigo de Cores Pintura (Especificao
Tcnica da PETROBRAS)
MSS SP-25 Standard Marking System for Valves, Fittings, Flanges and Unions, Jan
1998
3. DEFINITIONS
VET: Fully Tight Valves.
EPCista - Service provider, PETROBRAS supplier responsible for the EPC contract
(Engineering, Procurement and Construction)
Vendor List - List of qualified companies to supply equipment, materials and services.
4. GENERAL REQUIREMENTS
These requirements are applied to conventional valves and VETs.
4.1. Inspection and Testing Plan (PIT)
4.1.1. The Inspection and Testing Plan developed by the supplier shall allow the
identification of stages, throughout the valve production cycle, where it shall be done
checks or inspections, including those carried out by material or service suppliers.
Note: This document shall indicate the types of examinations, tests or checks to be
made, as well as procedures and/or applicable instructions, acceptance criteria and
issued records.
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
4
REV.
de
17
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
4.1.2. Critical Quota
It shall be controlled components critical quotas as defined by the manufacturer,
including, at least, standardized quotas in the construction and design standards of
valves.
4.1.3. PIT, designed by the valve manufactures, shall be approved by PETROBRAS.
4.1.4. The strategy of inspection and monitoring of tests by Petrobras shall be defined
based on the effectiveness verification demonstrated by the supplier in full compliance
with requirements of supplying inspection of the product.
4.2. Procedures and Instructions in PIT
4.2.1. Supplier shall have and present the procedures and instructions for inspection
of all expected activities in PIT.
4.2.2. The procedures shall present the acceptance criteria and reference standards
or specifications of which were based on, they shall also be submitted for review and
comments by the inspection responsible company and posterior approval by
PETROBRAS.
4.3. Inspection and Tests
4.3.1. Qualified companies to provide services for the supervision, inspection and
testing of valves, cited in this Specification, shall be registered in the Vendor List of the
project or supply contract.
4.3.2. The final inspection shall be done on the manufacturer facilities, which shall be
witnessed and approved by a supervisor or professional (inspector), indicated or
approved by PETROBRAS, or Member Company to the Project "Vendor List",
qualified by PETROBRAS/E&P.
4.3.3. The final inspection shall include at least the following checks:
4.3.4. Final Inspection on 100% of the lot:
- Body: hydrostatic test.
- Sealing: pneumatic and hydrostatic tests.
4.3.5. Verification of identification, tracking, visual and dimensions, measurement of
wall thickness, functional testing, checking of the identification plaque, painting,
packaging, analysis of manufacturing records and other checks foreseen in the
contract and constructive standards.
4.3.6. Verification, by sampling, the actuation torque and the grasp torque of the joint
body and cover screws/prisoners.
4.3.7. According to PETROBRAS and justification, it may be allowed, in exceptional
cases, the disassembly of a valve for internal parts verification.
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
5
REV.
de
17
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
NOTE: PETROBRAS, as the final receiver of the hired items, reserves the right at any
time of the contract, of verifying the applicability of the supplier Quality System.
4.4. Pressure Tests
- It shall not be allowed the use of tape or Teflon paste (except cast iron valves,
bronze or resilient sealing) as an auxiliary element to seal threads, metal x metal (ex:
NPT).
- Cavity relief tests: when it is applicable, shall be made by the manufacturer,
witnessed, by sampling, by PETROBRAS. If it is confirmed the control of the process,
to ensure the repeatability of the specified characteristics in the homologated project,
the company can be released from this test under PETROBRAS approval.
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
6
REV.
de
17
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
TABLE A Recommended Pressure Test for Hydrostatic Testing of VETs
TEST PRESSURE TABLE (ASME / ANSI B 16.34)
TEST PRESSURE
VALVE CLASS(#)
VALVE WORKING
PRESSURE (PSI)
SEALING
PSI
Kgf/cm
150
285
313
22
300
740
814
57
400
990
1089
76
11
600
1480
1628
4
15
800
1973
2170
2
17
900
2220
2442
2
28
1500
3705
4075
6
47
2500
6170
6787
7
85
4500
11110
12221
9
NOTE: 1. Butterfly valves API 609, Category A, shall be tested according
manufacturer procedures.
2. Table based on recommended values by Standard ASME B16.34.
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
7
REV.
de
17
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
5.2.2 Test Duration.
The test duration, for hydrostatic testing of fully tight valves, shall be obtained from
Table B Indicated time for hydrostatic testing of VETs, below:
TABLE B Indicated time for hydrostatic testing of VETs
VALVE DIAMETER
TIME
(POL)
(MM)
(MINUTOS)
a1
15 a 40
2a4
50 a 106
5 a 10
125 a 250
12 a 18
300 a 450
20 e acima
500 e
acima
Obs.: Observing time shall start after the test pressure stabilization.
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
8
REV.
de
17
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
5.3. Body Hydrostatic Testing
The criteria set here for the hydrostatic test of the body are applicable to all series or
families of VET's defined in Appendix 14 of this Technical Specification.
5.3.1. Criteria for Testing Execution:
a. Before beginning the test, all surfaces of the valve shall be clean and dry.
b. The test fluid is filtered water, free from solids, at environmental temperature, with
chloride content of less than 30 PPM containing adequate inhibitor corrosion, to
ensure the integrity of the valve components. The fluid temperature of the test shall be
between 5 C and 50 C (API 598, ITEM 3.6.1).
c. The test shall be executed by applying to the internals of the valve (body), a
pressure equal to 1.5 times the valve working pressure, according to Table "A", and
duration according to Table "B".
The valve shall be tested in the partially open position (45), ensuring that it is
completely filled with the fluid test.
5.3.2. Criteria for Test Approval
a. Inspect the valve carefully for any lack of tightness (visual), noting cracks,
deformation or other porosity.
b. The test will be considered approved if there is no pressure drop or drip during its
execution.
5.4. Tightness Hydrostatic Testing
5.4.1. General Conditions:
The general conditions presented here for the hydrostatic testing of fully tight valves
are applicable to all series or families of VETs defined in Appendix 14 of this Technical
Specification.
a. The leak test is done by applying a pressure equal to 1.1 times the maximum valve
working pressure to the internal valve device, completely closed, according to values
defined in Table "A" and a duration time according to Table "B".
b. For valves equipped with automatic thermal relief device, it shall be confirmed it was
properly calibrated, certified and is permanently installed in the valve body. The set
shall be 1.25 times the valve working pressure found in the table "A" for their
respective
class.
c. All valves shall be painted and with all accessories mounted for the tightness test.
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
9
REV.
de
17
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
d. The inspector in charge shall ensure, through the display device of lack of tightness
installed (transparent tube or hose), that internal complex is completely filled with the
fluid
test.
e. All valves with castle shall be tested in the vertical position, ensuring that their body
and cover are completely filled with the test fluid.
f. By the hydrostatic test finishing, the set valve + actuator shall be operated a few
times, covering at least one cycle of opening and closing in each flow direction, under
atmospheric pressure. This procedure shall also be repeated under a maximum
differential pressure specified for the actuator.
Note: The dimensions of the actuator shall consider as a safety factor, a minimum
torque to actuate the valve under a pressure value increased by at least 20% of P
indicated in the Data Sheet of the valve.
g. During the opening/closing operation of the valve, mentioned in the previous
paragraph, under maximum differential pressure, it shall be verified the actuator
maneuverability and coupling conditions, which shall not allow the rotary sliding of the
actuator.
h. For valves actuated by electric or pneumatic actuators, it shall de recorded their
opening/closing time, under maximum differential pressure, as defined in the Data
Sheet of the Actuator.
i. The measurement of the actuation torque shall be done during the tightness tests
and it shall include opening and closing torques under atmospheric pressure and
maximum differential pressure test.
j. It may be accepted the reduction of the tightness test pressure in the no preferential
valve direction, since this information is described in the manufacturer technical
documentation.
k. For valves with manual actuation without electric or pneumatic actuation device, the
P used in the test shall be, at most, equal to 1.1 times the value of Table "A".
5.4.2. Specific Conditions:
The specific conditions presented here for the tightness hydrostatic test of fully tight
valves are particular to the different series or families of VETs defined in Appendix 14 of
this Technical Specification:
- The manufacturer shall submit for PETROBRAS approval the pressure test procedure,
in accordance to the project and valve construction standards, including specific
requirements for different models of VET defined in Appendix 14 of this Technical
Specification.
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
10
REV.
de
17
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
- The series or families of VETs, described below, have specific characteristics which
shall be checked during the tightness hydrostatic tests:
a. For VETs Series 000- Ball Valve - Double block and floating seats, SELF RELIEF
type, are valid the following recommendations:
- The test shall be done in both flow directions and it shall be checked the tightness
visually through the valve cavity, which shall be open to the atmospheric pressure by the
testing device (transparent tube or hose) previously installed.
- The cavity relief test shall be done in both direction, with gradual pressure increasing,
and be recorded the cavity relief pressure, which shall not exceed 33% of valve working
pressure.
- This test shall be done by sampling.
b. For VET Series 000 - Ball valve with double block and floating seats, double piston
effect; VET Series 100- Plug valve with expanding slips, double block and fixed seats
with automatic thermal relief device, VET Series 500- Expanding Gate valve, double
block with cavity relief device installed, are valid the following recommendations:
- The test shall be done in both flow directions and it shall be checked the tightness
visually through the valve cavity, which shall be open to the atmospheric pressure by
the testing device (transparent tube or hose) previously installed.
- The tightness cavity test shall done with a hydrostatic test pressure as defined in
Table A and duration as defined in Table "B" used in the valve cavity, with endings
opened to atmospheric pressure.
5.5. Criteria for Pneumatic tests:
5.5.1. General Conditions:
The general conditions presented here for pneumatic testing of fully tight valves are
applicable to all series or families of VETs, as defined in Appendix 14 of this Technical
Specification:
5.5.1.1. Tests of low pressure, when required, shall be carried out at environmental
temperatures, with pressure between 600 and 700 kpa (according to API Standard
598), independently of operating pressure or valve pressure class.
5.5.2. Special Conditions
5.5.2.1. Similarly to hydrostatic testing, the manufacturer shall submit to previous
PETROBRAS approval, the pneumatic testing procedure of low pressure, in
accordance to the project and valve construction standards, including specific
requirements for different models of VET defined in Appendix 14 of this Technical
Specification.
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
11
REV.
de
17
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
5.5.2.2. For VET Series 000 - Ball Valve with double block and floating seats, double
piston effect; VET Series 100- Valve type male with expandable shoes, double block
and fixed seats with automatic thermal relief device VET Series 500- Expanding Gate
Valve, double block with cavity relief device installed, are valid the following
recommendations
a. The test shall be done in both flow directions and it shall be checked the tightness
visually through the valve cavity, which shall be open to the atmospheric pressure by a
testing device meant for leaking detection.
b. The tightness cavity test shall be done with the test pressure, defined in Section 6.3,
and duration according to table "B", applied to the valve cavity, with endings opened to
the atmospheric pressure.
c. To carry out these tests the valve shall be completely dry and clean, internally and
externally.
d. If necessary, to ease leak visualization, it can be used soapy solution or equivalent,
which enables the identification of bubbles.
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
12
REV.
de
17
TTULO:
APPENDIX 20
table
follows:
1. Open to close position, with the valve passage pressurized and with the body cavity
under atmospheric pressure.
2. Close to open position, with both sides of the valve pressurized and body cavity
opened to atmospheric pressure.
3. Close to open position, with one valve side (A) pressurized along with the body
cavity and the other side (B) opened to atmospheric pressure.
4. Close to open position with one valve side (B) pressurized along with the body
cavity and the other side (A) opened to atmospheric pressure.
Note: The beginning, intermediate and resettlement torques shall be recorded where
applicable.
6.3. Relief Test of the Body Cavity Seat.
6.3.1. The relief test of the body cavity seat shall be done after the hydrostatic test and
before the functional tests.
6.3.2. The valve shall be in the fully closed position.
6.3.3. It shall be increased the pressure in the body cavity, gradually, until the pressure
is released, the same shall be done until the second seat releases the pressure.
6.3.4. The results shall be recorded in reports or forms for valve documentation.
7. POST-TEST ACTIVITIES
These requirements are applied to conventional valves and VETs.
7.1. PETROBRAS Standard Painting
7.1.1. When the painting process is part of the contract, the supplier shall present the
valve painting plan, according to PETROBRAS and approved by Painting Inspector
Level II.
7.1.2. Painting Inspection Plan, as well as training records of the professionals
involved in the painting process shall be submitted to PETROBRAS before services
begun.
7.1.3. Painting Inspection Records shall be presented to the contract processes.
7.1.4. The supplier shall foresee in the Painting Plan that the surface areas between
flanges of the union body x cover and castle be painted according to painting
procedure contract. Ex: manufacturer standard.
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
13
REV.
de
17
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
7.1.5. The color definition applied to valves shall meet the ET-3000.00-1200-956-PCI001 (Color Code Painting, for UEPs).
7.2. Identification, Marking and Traceability.
7.2.1. The supplier shall have instruction which defines the systematic of identification,
marking and traceability of valves components mounted.
7.2.2. The supplier shall physically identify and track all critical components defined by
the project, for each product, through traceability lists of components and/or fabrication
lot
per
product.
7.2.3. Each valve shall be identified with an individual serial number, beyond the
individual identification of components defined as critical, enabling their effective
traceability. The identification component per lot is allowed only if this systematic
allows tracking all critical components per valve.
7.2.4. Valves and their components shall be identified according to manufacturing
standard and to the Standard MSS SP-25.
7.3. Handling, Preservation, Storage, Packaging and Shipping
7.3.1. The supplier shall submit for analysis, comments and PETROBRAS approval a
method that defines the systematic of handling, preservation, packaging and shipping
to all components and equipment included in scope of supply (including actuators).
7.3.2. The packing of the valves shall be done according to PETROBRAS, to ensure
that the valves do not suffer damages during handling and transportation between the
factory and the facility.
7.3.3. The method shall include conservation conditions of seat components and
endings throughout the production, especially after the tightness tests, where it shall
be checked the cleaning and drying of the valves before packing.
7.3.4. This method shall also inform the antioxidant used for internal parts protection,
as well as unpainted external parts, such as screws, nuts and bezels. (Figure 1).
7.3.5. For valves made of brass, stainless steel and other metal alloys called "nonoxidizable", the method shall indicate the protective against dust and moisture.
7.3.6. After the protective application, all valves shall have their cavities blocked by
rubber plates or plastic material, and glued outer surfaces of the flanges in order to
keep out dust and moisture.
7.3.7. The valves which do not have proper conditions to remain upright, shall be
supported by wooden board bolted to the flanges and mounted on a rubber protection
or plastic film, allowing its positioning in the upright. (Figure 2)
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
14
REV.
de
17
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
7.3.8. After preservation, valves shall be blocked for transportation, as follows:
- Ball valves and valve type male in the open position;
- Other types of valves in the close position.
7.4. Quality Records Archiving
The minimum time of records archiving shall be "FIVE YEARS".
7.5. Data-Book
Unless otherwise specified in the contract, Material Request or Technical
Specification, the national or foreign supplier shall elaborate the Valve "Data-Book",
containing at least the following items:
-
Certificates of Compliance;
Reports of Non-compliance and Corrective Actions taken, relevant to the delivered
product;
PIT Copy approved by Petrobras;
Copy of all reports issued by the company responsible for inspection and approved
by PETROBRAS.
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
15
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
FIGURE 1
PROTETIVO
REV.
de
17
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
16
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
FIGURE 2
REV.
de
17
TECHNICAL SPECIFICATION
E&P
N:
ET-3000.00-1200-200-PCI-001
FOLHA:
17
REV.
de
17
TTULO:
APPENDIX 20
Industrial Valve Supply Requirements for E&P
8. RECEIVING INSPECTION
These requirements are applied to conventional valves and VETs.
8.1. The receiving inspection shall be done without causing damages to the package
and without compromising the preservation of the valves.
8.2. It shall be carried out the documentation verification and its compliance with the
product (plaque identification, serial number, valve pressure class, etc.).
8.2.1. This documentation shall also contain the Certificate of Material Releasing, at
the factory, duly signed by PETROBRAS representative and the Manufacturer's
Manual containing handling and preservation procedures.
8.2.2. After verifying the documentation and attesting its conformity, the packed valve
shall be sent to storage in a suitable location.
9. STORAGE
The storage location of the valves, as well as their preservation plan, shall be
inspected and approved by PETROBRAS representative.
10. RECOMMENDATIONS ON VET INSTALLATION
10.1. VETs shall only be removed from storage location, after certifying that the lines
where they will be installed are thoroughly clean, by certificate of boroscope.
10.2. The valve packing shall only be removed at the time of installation.
10.3. The method for tightness visualization of in-line valves shall be through pressure
drop in the manometer used by the staff responsible for piping assembly, during the
line tightness test.
10.3.1. If it is verified lack of tightness in a valve during line tests, it shall be withdrawn
and re-evaluated in certified bench, in the presence of manufacturer's technical and
other parties involved.
10.3.2. After line tightness test, where there are VETs installed, the responsible for
preservation shall ensure that they, along with the valves, are properly preserved in
order to ensure non-oxidation of the valves.
N:
TECHNICAL SPECIFICATION
CLIENT:
E&P
DR-ENGP-1.1
SHEET:
of
27
PROGRAM:
AREA:
TITLE:
APPENDIX 21
E&P - ENGP
Index
Date
Project
Execution
Verification
Approval
1.0 - Scope...............................................................................................
pg.02
pg.02
3.0 - Definitions ..
pg.02
pg.03
pg.04
pg.05
pg.14
pg.22
pg.25
Rev. 0
Rev. A
Sep/10
E&P
EISA
IPP
ENGP
Nov/10
E&P
EISA
IPP
ENGP
Rev. B
Rev. C
Rev. D
Rev. E
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORM N-381 REV. G
Rev. F
Rev. G
Rev. H
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
2
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
1.0- Scope
1.1. This appendix establishes the minimum mandatory requirements for design,
production, inspection, testing and acceptance of welding for Inconel 625 combined
with carbon steel pipes in the form of weld overlay. Upon completion of the welding
process, the minimum thickness of the deposition of Inconel 625 should be 3.0 mm.
1.2. This appendix specification applies to:
Piping systems constructed using ASME B31.3 code: process piping;
Gas pipelines constructed according to ASME B31.8: gas transmission
distribution and piping systems (only topside interface at pig launcher and
receiver system) ;
Oil pipelines constructed according to ASME B31.4: pipeline transportation
systems for liquid hydrocarbons and other liquids (only topside interface at
pig launcher and receiver system).
TECHNICAL SPECIFICATION
N:
REV.
DR-ENGP-1.1
SHEET:
E&P
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
ASTM G 48: Standard Test Methods for Pitting and Crevice Corrosion
resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride
Solution;
AWS Code;
DNV OS F101: Submarine pipeline systems;
ISO 3834-2: Quality requirements for fusion welding of metallic materialspart 2: comprehensive quality requirements;
ISO-15590-1 Induction Bending;
ISO-8501-1: Preparation of steel substrates before application of paints and
related products - Visual assessment of surface cleanliness.
NACE MR 0175/ISO 151546: petroleum and natural gas industries materials for use in h2s-containing environments in oil and gas production;
3.0-
Definitions
For the purposes of this appendix the definitions indicated in items 3.1 to 3.2 are adopted.
3.1 Clad/Cladding
Refers to a metallurgically-bonded CRA layer produced by roll bonding, weld overlaying,
powder metallurgy or explosively cladding a carbon steel plate or pipe.
4.1. For welded overlay surface involving inconel 625 and carbon steels (weld ovelay
process), shall be used Gas -Tungsten-Arc (GTAW) and GTAW-Hot Wire (GTAW-Hot
Wire-pipe clad, mechanized process).
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
4
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
5.0- Consumables (wire and gas)
5.1. Materials shall be provided with the respective certificates of fabrication according
to the applicable standards. For welding consumables (wire and gas), the requirements
listed below shall be applied:
figure 1
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
5
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
6.0- Manufacturing procedure specification - weld overlay clad pipe .
6.1- Manufacturing Procedure Specification For CRA Cladded Pipe and Fitting Internal
Carbon Steel Pipe With UNS N06625
ITEM N
DESCRIPTION REMARKS
DESCRIPTION REMARKS
CS Base Pipe for cladding:
2.0 QUALIFICATION OF
Qualification of Weld Overlay
WELD OVERLAY PROCEDURE Procedures.
Acceptance Criteria
TECHNICAL SPECIFICATION
N:
REV.
DR-ENGP-1.1
SHEET:
E&P
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
2. Chemical Analysis (Overlay)
Check chemical analysis shall be
made on sample taken from one
test piece. Locations of chemical
analysis to be at distance of 3mm
above fusion line as QW-462.5(a)
Additional tests may be made at
different locations for information.
Chemical analysis performed per
ASTM A751 using optical emission
spectrometer (OES) or by X-ray
fluorescence (XRF) test methods.
58% min
20.0-23.0%
8.0-10.0%
5.0% max
4. ASME IX QW195.2Acceptance
Criteria (also ASME VIII Div 1
App 8).
The following are unacceptable:
(i) any relevant linear indications
(ii) any relevant rounded
indications
greater than 4.8mm
(iii) four or more relevant
rounded
indications in a line separated by
1.6mm or less (edge to edge).
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
7
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
3.0 QUALIFICATION OF
BUTT WELD PROCEDURE
Acceptance Criteria
4.0 QUALIFICATION OF
WELD REPAIR
PROCEDURE
TECHNICAL SPECIFICATION
N:
REV.
DR-ENGP-1.1
SHEET:
E&P
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
Additional qualification to be
performed where required but only
if the Weld Repair WPS is not
already qualified by the Weld
Overlay WPS
qualification outlined in section 2.0
above.Where required, new
qualifications to be based
on existing weld overlay cladding
procedures including documented
method statement and supported
by following testing:
58% min
20.0-23.0%
8.0-10.0%
5.0% max
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
9
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
5.0 WELDING
PERFORMANCE
QUALIFICATION
4. ASME IX QW-195.2
Acceptance Criteria (also ASME
VIII Div 1 App 8).
5. Dimensional check.
Carry out survey of weld overlay
including repair.
1. Welding Operators
1. Unexpired Qualification
All welding operators used in
Records as per
production shall be qualified (within ASME IX QW 322.
the past 6 months)
for use in accordance with ASME
IX QW- 305, QW 381 and QW 453
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
10
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
2. Welders
All welders used in production
shall be qualified (within the past 6
months) for use
in accordance with ASME IX QW304, QW
381 and QW 453.
2. Unexpired Qualification
Records as per
ASME IX QW 322.
Acceptance Criteria
Visual inspection for cleanliness
per ISO8501-1
with SA 2.5 minimum. Random
sample inspection
using video camera or similar to
check full length.
If surface scale is visible, pipe to
be re-blasted.
Acceptance Criteria
Visual inspection.
Pipe ends reasonably square for
set up and start
of weld overlay cladding (visual
check).
9.0 WELDING
9.1 Production Welding
10
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
11
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
Butt welds will be performed as
required using manual GTAW /
TIG welding with ERNiCrMo-3
consumable.
No post weld heat treatment
required
9.2 Repair
10.0 NDT
Pipe Body-External
1. 100% manual UT examination
for lack of bond and sub-surface
discontinuities on clad pipe
(scanned from external surface)
Acceptance Criteria
d. No relevant indications in
pressure contact
sealing surfaces (e.g. flange
gasket faces).
11
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
12
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
using straight beam, contact and
pulse echo ultrasonic technique in
accordance with ASME V Article5.
Primary reference level set using
calibration block with FBH
12
TECHNICAL SPECIFICATION
N:
REV.
DR-ENGP-1.1
SHEET:
E&P
13
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
Acceptance Criteria
58% min
20.0-23.0%
8.0-10.0%
5.0% max
13
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
14
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
NOTE: Check analysis required
only when the Alloy 625 (UNS
N06625) welding consumable
heat changes (see test frequency
note below)
2. Corrosion Test on Weld Overlay
ASTM G48
Method A Ferric Chloride Pitting
Test. One sample taken from top
layer of weld overlay cladding for
G48A testing. Carbon steel
substrate removed prior to testing.
Examine specimen faces after
testing. Edge pits, if present, are
disregarded during evaluation
.
NOTE: Corrosion test required
only when the Alloy 625 (UNS
N06625) welding consumable heat
changes (see test frequency note
below).
14
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
15
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
Acceptance Criteria
12.0 PMI
Positive Material Identification
(PMI) testing performed using
portable XRF alloy analyzer
(Innov-X Alpha) on one accessible
area of finished overlay cladding at
sampling rate of one reading per
component (one per pipe,
one per flange, one per bend).
Material grade identification is
based on Ni, Mo, Cr, Fe
content using Innov-X analyser
standard accuracy and integral
material grade library.
In cases where PMI testing of the
weld deposit is not possible
because of the geometry of the
item being tested, the verification
of the welding wire identification
markings is an acceptable
substitute.
PMI testing may be performed
either during or after production
cladding operations.
Acceptance Criteria
Smooth surface finish. Where
machined, surface finish to be
free from visible tool chatter
marks, burrs or flat areas.
15
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
16
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
Acceptance Criteria
Where contamination of the weld
overlay is suspected, copper
sulphate test is performed
per ASTM A380, subject to HSE
restrictions, on accessible finished
overlay surfaces to check for the
presence of free iron.
Prepare copper sulphate solution
as per ASTM A380, swab or spray
the surface of the overlay with
copper sulphate solution, keep wet
with additional solution if
necessary and leave for a
minimum of 6 minutes. Rinse with
potable water spray (with less than
50ppmchloride in the water) and
air dry. Visually examine for signs
of copper deposit that indicate the
presence of free iron.
Acceptance Criteria
16
TECHNICAL SPECIFICATION
N:
REV.
DR-ENGP-1.1
SHEET:
E&P
17
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
except for overlapping areas
(start-stop, etc).
No gaps of any width between
the weld beads are permitted.
Overlapping weld beads
with locally increased deposit
thickness are allowed provided
the minimum cladding thickness
requirement is met and that NDE
of the weld overlay is
satisfactory.
Bending radius
For R 5D: (+25%, -0%)
For 5D < R 10D: (+100%, -0%)
For R > 10D (+unlimited, -0%)
Nominal base material diameter
None
+ 3,0 mm
Process
7.2.1
Description
1. The following items will be checked on base
material pipe:
- Material
- Outside diameter
- Wall thickness (see Note 1)
17
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
18
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
- Length
- Heat number and pipe number
- Appearance
- Quantity
Note 1: The wall thickness for each pipe shall be
measured by ultrasonic thickness tester before
bending in three locations along the mother pipe. For
each location shall be measure four
7.2.2
7.2.3
Ultrasonic Testing
7.2.4
Marking
7.2.5
Induction Bending
18
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
19
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
- The area to be bent is locally induction heated from
the outside surface.
- The bend is pushed forwards at a constant speed
so that bending stress is concentrated at the
heat zone and therefore continuously reformed to
produce the desired bend.
3. Essentials variables and Maximum permissible
variations.
- Heat Temperature: 1050C 50C (deviation from
ISO 15590 table 2.)
- Bending Speed: 0,5 mm/s 0.04 mm/s
- Coil Design: None
- Cooling Method: Forced Air
- Cooling flow rate or pressure: 3,5 kgf/cm 10%
- Induction heating frequency: 20%
7.2.6
7.2.7
19
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
20
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
7.2.8
Dimensional Inspection
7.2.9
Wall Thickness
3.Tolerance:
- For 5D bends the maximum wall thinning shall be
10%.
7.2.10
Out of Roundness
7.2.11
Bend Radius
20
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
21
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
7.2.12
Bend Angle
7.2.13
21
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
22
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
(a)
Visual Inspection
(b)
Ultrasonic Testing
(c)
Liquid Penetrant Testing
(d)
(e)
7.2.14
22
TECHNICAL SPECIFICATION
N:
REV.
DR-ENGP-1.1
SHEET:
E&P
23
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
7.2.15
(a)
Tangent Ends
23
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
24
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
(b)
(c)
Out-of- Planeness
7.2.16
Identification
24
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
25
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
This item establishes the recommended practices for prepare and qualify the butt welding
joints procedure specification (WPS). However, all welding documents shall be prepared
and qualified by a welding inspector qualified (see annex A).
8.1. For welding pipe to pipe or pipe to fittings joints (butt-welding joints), can be used
gas -tungsten-arc (GTAW - manual process) and SMAW process.
Qualification of GTAW / SMAW Butt Weld WPS to be performed using multiple layer ERNiMoCr-3
welding consumable in accordance with the requirements of ASME B31.3 and ASME IX.
Base material used for the weld qualification shall be from same material grouping as API 5L
and ASTM A694 F60 (ASME IX QW-422)
Note PWHT is not required.
Testing to be performed on weld qualification test coupons as required by ASME IX including
radiographic examination, tensile testing, guided bend testing, chemical analysis and corrosion
testing as outlined above.
Note: Change of filler metal brand name and manufacturing location are not considered
essential variables.
8.2 Consumable
Specifications: AWS A 5.11;
Specifications: AWS A 5.14;
Classifications: ER Ni Cr Mo-3;
8.3 Gas
shielding argon - 99,99 %;
backing argon 99,99% (if applicable).
25
TECHNICAL SPECIFICATION
N:
REV.
DR-ENGP-1.1
SHEET:
E&P
26
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
Acceptance Criteria
If any testing additional to the under mentioned requirements is undertaken during testing of the
actual procedure qualification, the additional test results can be included in the resultant final
PQR but strictly for information only.
NOTE: As required by B31.3 para 328.2, test weldments shall be made based on the material
groupings taken from ASME IX QW-422Base material selected for butt weld procedure
qualification testing shall follow ASME IX as perQW-420.1 and QW-420.2. In this case, base
material for weld procedure qualification will be S-Number 1 Group 2 (e.g. API 5L-X60/X65).
This will qualify API 5L pipe-to-pipe butt welds as well as API 5L ASTM A694
pipe-to-flange butt welds.
NOTE: As required, where the butt weld is to be completed using ERNiCrMo-3 consumable for
all weld passes, the clad pipe bevel may be pre butte redusing 3mm thick layer of Alloy 625
UNS N06625, applied using manual GTAW in accordance with approved weld procedure, so as to
ensure that the root pass of the butt weld is not diluted with Fe.
26
TECHNICAL SPECIFICATION
N:
SHEET:
E&P
REV.
DR-ENGP-1.1
27
of
27
TITLE
Appendix 21
Welding Qualification for Inconel 625 Weld Overlay Clad Pipe.
c) Welders or welding operators who are have been performing welding activities
without interruption for over three months, and were qualified for other jobs at
PETROBRAS, can be used, so long as they present qualification records,
accompanied by their respective individual certificates (original documents),
properly approved by a qualified welding inspector and endorsed by
PETROBRAS Inspection of previous jobs;
d) Welders or welding operators who have not performed welding for three or more
months, or who have not had their welds tested by radiography or ultrasonic,
must undergo retraining and re-qualification.
A.1.1.2. The contracted party shall present to PETROBRAS inspection, before
beginning of activities, the list of operators and inspectors qualified to perform
and inspect the services.
A.1.1.3. welders and welding operators who present a biweekly repair rate above the
following established values, shall be retrained and re-qualified:
- 2.5% (two point five percent) or 75 (seventy-five) mm in 3 (three) meters of tested
welds, when the rate is calculated by defect length; or
- 10% (ten percent) or 2 (two) radiographies for every 20 (twenty) radiographies
examined sequentially, when the rate is calculated by number of radiographies.
27
N:
TECHNICAL SPECIFICATION
CLIENT:
E&P
PROGRAM:
of
90
ET-200.03
TITLE:
TAG
SHEET:
AREA:
E&P - ENGP
DR-ENGP-1.1
Valves Description
Spec
Description
VAG-08
A8 B14 B20
B21 B22 B23
B24 C14 E14
F14
VAG-09
G14
VAG-17
B4 B9 B10
B15 C4 C9
C10 E4 E9
E10 E10R F4
F10 F10R
VAG-18
G4 G10 H10 Globe valve; carbon steel; union bonnet; needle disc; inside
screw stem; rising stem; socket weld ends MSS SP-84;
ASME B16.34 standard; body-seat ASTM A 105; needle A
564 type 630; max. pressure 5000 psi.
VAG-21
VAG-23
G6 G6R G19 Globe valve; carbon steel; union bonnet; needle disc; inside
screw stem; rising stem; socket weld ends MSS SP-84;
ASME B16.34 standard; body-seat ASTM A 350 Gr LF2 CL
1; needle A 564 type 630; max. pressure 5000 psi.
VAG-26
Date
Project
Execution
Verification
Approval
Original
REV. F
REV. G
REV. H
REV. J
REV. K
REV. L
REV. 1
REV. 2
Dec/78
DEPRO
M. Assayag
Hernon
Hernon
Nov/05
E&P
Fernando
Hernon
Joper
Dec/05
E&P
Fernando
Hernon
Joper
Jan/06
E&P
Fernando
Hernon
Joper
Mar/06
E&P
Fernando
Hernon
Joper
May/06
E&P
Fernando
Hernon
Joper
Feb/07
E&P
Fernando
Hernon
Joper
Nov/09
E&P
Carlos
Fernando
Cludio
Sep/10
E&P
EISA
IPP
ENGP
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORM N-381 REV. F
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
90
TITLE:
Valves Description
TAG
VAG-27
Spec
G3 H3
Description
Globe valve; stainless steel; union bonnet; needle disc;
inside screw stem; rising stem; socket weld ends MSS SP84; ASME B16.34 standard; body-seat ASTM A 182 Gr
F321; needle AISI 321; max. pressure 5000 psi.
VAG-28
B12 C12
VAG-29
B13 C13
VAG-30
G12 G12P
VAG-31
B11 C11
VAG-32
G11
VAG-33
H11
VAG-34
J12
VAG-35
B16 C16
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
90
TITLE:
Valves Description
TAG
VAG-40
Spec
C30 E30
Description
Globe valve; Inconel 625 alloy steel; union bonnet; needle
disc; inside screw stem; rising stem; buttweld ends, ASME
B16.25; ASME B16.34 standard; body-seat-needle ASTM B
564 (UNS N06625); max. pressure 3000 psi.
VAG-41
H30 H30P
VAG-42
J31
VAG-43
H14
VAG-44
H3
VB-01
A4
VB-02
A4
VB-03
B5
VB-09
A4 B5
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
90
TITLE:
Valves Description
TAG
Spec
VB-10
A4
Description
VB-11
B7R B10 B14 Butterfly valve; wafer; ductile iron; wrench operator, 90
B22 B24 degress rotation; body-disc ASTM A 536 Gr 65-45-12; bodyseat coated with Viton; disc coated with Nylon 11; solid stem
AISI 316; API 609 category A standard; max. pressure 150
psig.
VB-12
B7R B10 B14 Butterfly valve; wafer; ductile iron; lateral gear operator;
B22 B24 body-disc ASTM A 536 Gr 65-45-12; body-seat coated with
Viton; disc coated with Nylon 11; solid stem AISI 316; API
609 category A standard; max. pressure 150 psig.
VB-12A
B7R B10
VB-13A
B14 B22
VB-14
B10 B15
VB-15
B10 B15
VB-15A
B10 B15
VB-16
B10 B15
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
90
TITLE:
Valves Description
TAG
Spec
Description
standard; max. pressure 250 psig.
VB-17
B10 B15
VB-17A
B10 B15
VB-18
VB-19
B7 B7R B10 Butterfly valve; wafer; ductile iron; lateral gear operator;
B14 B22 B23 body-disc ASTM A 536 Gr 65-45-12; body-seat coated with
Viton; disc coated with Nylon 11; solid stem AISI 316; API
609 category A standard; max. pressure 250 psig.
VB-19A
B7 B7R B10 Butterfly valve; flanged type; ductile iron; lateral gear
operator; body-disc ASTM A 536 Gr 65-45-12; body-seat
coated with Viton; disc coated with Nylon 11; solid stem AISI
316; API 609 category A standard; raised face (RF) class
150, ASME B16.47 Series A; max. pressure 250 psig.
VB-20
B23
VB-20A
B14 B22
VB-21
B25
VB-22
B25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
90
TITLE:
Valves Description
TAG
Spec
Description
Hypalon seat; API 609 category A standard; max. pressure
250 psig.
VB-22A
B25
VB-23
B15
VB-24
B15
VB-24A
B15
VB-25
B7R B15
VB-26
B7R B15
Butterfly valve; wafer; Ni/Al/Br; lateral gear operator; bodydisc-stem ASTM B148 UNS C95800; Viton seat; API 609
category A standard; max. pressure 150 psig.
VB-26A
B7R B15
VB-27
B20
VB-28
B21
VB-29
B7R
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
90
TITLE:
Valves Description
TAG
Spec
Description
ASME B16.5 standard; max. pressure 250 psig.
VB-29A
B7R
VB-32
B11
VB-33
B11
VB-33A
B11
VE-01
C8 E8
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; screwed ends
ASME B1.20.1 NPT; body ASTM A 105; AISI 410 trim; soft
seat; ISO 17292 standard; class 800.
VE-04C
B15
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
soft seat; ISO 17292 standard; class 800.
VE-05B
F10R
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 105; AISI 410 trim;
soft seat; ASME B16.34 LTD standard; class 1500.
VE-05C
F10R
VE-06
B6
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
soft seat; ASME B16.34 LTD standard; class 1500.
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 352 Gr LCB;
AISI 304 trim; soft seat; ISO 14313 (API 6D) standard; class
150.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
90
TITLE:
Valves Description
TAG
Spec
VE-07
B6
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 150.
VE-07A
B6
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; raised face (RF); body
ASTM A 352 Gr LCB; AISI 304 trim; soft seat; ISO 14313
(API 6D) standard; class 150.
VE-08
C6
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 352 Gr LCB;
AISI 304 trim; soft seat; ISO 14313 (API 6D) standard; class
300.
VE-09
C6
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 300.
VE-10
B15
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; AISI 410
trim; soft seat; ISO 14313 (API 6D) standard; class 150.
VE-10E
A8 B14
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 105; AISI 410
trim; soft seat; ISO 14313 (API 6D) standard; class 150.
VE-10G
Description
B22 B23 B24 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 105; AISI 316
trim; soft seat; ISO 14313 (API 6D) standard; class 150.
VE-11E
C14
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 105; AISI 410
trim; soft seat; ISO 14313 (API 6D) standard; class 300.
VE-13
E10R E14
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
90
TITLE:
Valves Description
TAG
Spec
Description
A 105; AISI 410 trim; soft seat; ISO 14313 (API 6D) standard;
class 600.
VE-14
F10R F14
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; soft seat; ISO 14313 (API 6D) standard;
class 900.
VE-15
F10R F14 Ball valve; full bore; carbon steel; bolted body; trunnionG10R G14 mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; soft seat; ISO 14313 (API 6D) standard;
class 1500.
VE-16
H10 H14
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; soft seat; ISO 14313 (API 6D) standard;
class 2500.
VE-17
B15
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; soft seat; ISO 14313 (API 6D) standard; class
150.
VE-17E
A8 B14
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 216 Gr WCB; AISI
410 trim; soft seat; ISO 14313 (API 6D) standard; class 150.
VE-17G
B22 B23 B24 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 216 Gr WCB; AISI
316 trim; soft seat; ISO 14313 (API 6D) standard; class 150.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
10
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-18E
C14
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 216 Gr WCB; AISI
410 trim; soft seat; ISO 14313 (API 6D) standard; class 300.
VE-20
E10R E14
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 600.
VE-21
F10R F14
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 900.
VE-22E
A8 B14
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; flat face (FF); body ASTM A 216
Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 150.
VE-22F
B14
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; flat face (FF); body
ASTM A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313
(API 6D) standard; class 150.
VE-23E
C14
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; flat face (FF); body ASTM A 216
Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 300.
VE-23F
C14
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; flat face (FF); body
ASTM A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313
(API 6D) standard; class 300.
VE-25
E10R E14
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 600.
Ball valve; full bore; carbon steel; bolted body; trunnion-
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
11
of
90
TITLE:
Valves Description
TAG
VE-26
Spec
F10R F14
Description
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 900.
VE-27
G10R G14 Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 1500.
VE-28
H10 H14
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 2500.
VE-28P
H10P
Ball valve; piggable; fire tested; full bore; carbon steel; bolted
body; trunnion-mounted; handwheel gear operator, 90
degrees rotation; flanged ends ASME B16.5; ring type joint
(RTJ); body ASTM A 216 Gr WCB; AISI 410 trim;
soft/metallic seat; ISO 14313 (API 6D) standard; class 2500.
Note: Internal diameter (ID) valve shall be defined for Project
Engineer.
VE-44
A8 B14
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 105; AISI 410
trim; soft seat; ISO 17292 standard; class 150.
VE-45
C14
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 105; AISI 410 trim;
soft seat; ISO 17292 standard; class 300.
VE-46
E14
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 105; AISI
410 trim; soft seat; ISO 17292 standard; class 600.
VE-47
F14 G14
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; soft seat; ASME B16.34 LTD standard;
class 1500.
VE-48B
B9 B10 C9 Ball valve; full bore; carbon steel; bolted body; floating ball;
C10
wrench (lever) operator, 90 degrees rotation; socket weld
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
12
of
90
TITLE:
Valves Description
TAG
Spec
Description
ends with nipple Sch 80; body ASTM A 105; AISI 410 trim;
metal-metal; ISO 17292 standard; class 800.
VE-48C
B10 C10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
metal-metal; ISO 17292 standard; class 800.
VE-48D
B5 B9 C5 C9 Ball valve; full bore; carbon steel; bolted body; floating ball;
E5
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch XXS; body ASTM A 105; AISI 410 trim;
metal-metal; ISO 17292 standard; class 800.
VE-49D
F5 G5
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple Sch XXS; body ASTM A 105;
AISI 410 trim; metal-metal; ASME B16.34 LTD standard;
class 1500.
VE-50
B9 B10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; AISI 410
trim; metal-metal; ISO 14313 (API 6D) standard; class 150.
VE-51
C9 C10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; AISI 410
trim; metal-metal; ISO 14313 (API 6D) standard; class 300.
VE-64B
B6
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A350 Gr LF2 CL1; AISI
304 trim; metal-metal; ISO 17292 standard; class 800.
VE-64C
B6
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 350 Gr LF2 CL1;
AISI 304 trim; metal-metal; ISO 17292 standard; class 800.
VE-65
B6
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 352 Gr LCB;
AISI 304 trim; metal-metal; ISO 14313 (API 6D) standard;
class 150.
VE-66
B6
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
13
of
90
TITLE:
Valves Description
TAG
Spec
Description
flanged ends ASME B16.5; raised face (RF); body ASTM A
352 Gr LCB; AISI 304 trim; metal-metal; ISO 14313 (API 6D)
standard; class 150.
VE-66A
B6
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; raised face (RF); body
ASTM A 352 Gr LCB; AISI 304 trim; metal-metal; ISO 14313
(API 6D) standard; class 150.
VE-67
B9 B10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; metal-metal; ISO 14313 (API 6D) standard;
class 150.
VE-68
B9 B10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB; AISI 410 trim; metal-metal; ISO 14313 (API
6D) standard; class 150.
VE-68A
B9 B10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; raised face (RF); body
ASTM A 216 Gr WCB; AISI 410 trim; metal-metal; ISO
14313 (API 6D) standard; class 150.
VE-69
C9 C10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; metal-metal; ISO 14313 (API 6D) standard;
class 300.
VE-70
C9 C10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB; AISI 410 trim; metal-metal; ISO 14313 (API 6D)
standard; class 300.
VE-74
B13 C13
VE-75
B12 C12
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
14
of
90
TITLE:
Valves Description
TAG
Spec
Description
socket weld ends with nipple Sch 40S; body-ball ASTM A 182
Gr F55 (UNS S32760); soft seat; ISO 17292 standard; class
800.
VE-76
B12 B13
VE-77
B12 B13
VE-77A
B12
VE-78
C12 C13
VE-79
C12 C13
VE-80
C12
VE-83
C12
VE-84
C12
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
15
of
90
TITLE:
Valves Description
TAG
Spec
Description
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; raised face (RF); bodyball ASTM A 995 Gr 5A (UNS J93404); metal-metal; ISO
14313 (API 6D) standard; class 300.
VE-91B
C6 E6 E6R Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 350 Gr LF2 CL1;
AISI 304 trim; soft seat; ISO 17292 standard; class 800.
VE-91C
C6 E6 E6R Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 350 Gr LF2 CL1;
AISI 304 trim; soft seat; ISO 17292 standard; class 800.
VE-92
E6 E6R
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 600.
VE-93
E6 E6R
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 600.
VE-94B
F6 F6R
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 350 Gr LF2 CL1;
AISI 304 trim; soft seat; ASME B16.34 LTD standard; class
1500.
VE-94C
F6 F6R
VE-94D
G6 G6R G19 Ball valve; full bore; carbon steel; bolted body; trennion
assembly; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple XXS; body ASTM A 350 Gr LF2
CL1; AISI 304 trim; soft seat; ASME B16.34 LTD standard;
class 1500.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
16
of
90
TITLE:
Valves Description
TAG
VE-95
Spec
Description
F6 F6R G6 Ball valve; full bore; carbon steel; bolted body; trunnionG6R G19 mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 1500.
VE-96
F6 F6R
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 900.
VE-97
F6 F6R
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 900.
VE-99
G6 G6R G19 Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 1500.
VE-102B
F10R
Ball valve; fire tested; full bore; carbon steel; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple Sch 80; body ASTM A 105; AISI
410 trim; soft/metallic seat; ASME B16.34 / ISO 10497
standard; class 1500.
VE-102C
F10R
Ball valve; fire tested; full bore; carbon steel; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple Sch 160; body ASTM A 105;
AISI 410 trim; soft/metallic seat; ASME B16.34 / ISO 10497
standard; class 1500.
VE-102D
VE-107
VE-108
G10P G10R Ball valve; fire tested; full bore; carbon steel; bolted body
floating ball; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple Sch XXS; body ASTM A 105;
AISI 410 trim; soft/metallic seat; ASME B16.34 LTD standard
/ ISO 10497; class 1500.
F10R
Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; wrench (lever) operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 105; AISI 410 trim; soft/metallic seat; ISO
14313 (API 6D) standard; class 900.
F10R G10R Ball valve; fire tested; full bore; carbon steel; bolted body;
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
17
of
90
TITLE:
Valves Description
TAG
Spec
Description
trunnion-mounted; wrench (lever) operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 105; AISI 410 trim; soft/metallic seat; ISO
14313 (API 6D) standard; class 1500.
VE-108P
G10P
Ball valve; piggable; fire tested; full bore; carbon steel; bolted
body; trunnion-mounted; wrench (lever) operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 105; AISI 410 trim; soft/metallic seat; ISO
14313 (API 6D) standard; class 1500.
Note: Internal diameter (ID) valve shall be define for Project
Engineer.
VE-109
H10
Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; wrench (lever) operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A105; AISI 410 trim; soft/metallic seat; ISO
14313 (API 6D) standard; class 2500.
VE-119
F10R
Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; wrench (lever) operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 216 Gr WCB; AISI 410 trim; soft/metallic seat;
ISO 14313 (API 6D) standard; class 900.
VE-125
F10 F10R
Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 216 Gr WCB; AISI 410 trim; soft/metallic seat;
ISO 14313 (API 6D) standard; class 900.
VE-126
G10R
Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 216 Gr WCB; AISI 410 trim; soft/metallic seat;
ISO 14313 (API 6D) standard; class 1500.
VE-126P
G10P
Ball valve; piggable; fire tested; full bore; carbon steel; bolted
body; trunnion-mounted; handwheel gear operator, 90
degrees rotation; flanged ends ASME B16.5; ring type joint
(RTJ); body ASTM A 216 Gr WCB; AISI 410 trim;
soft/metallic seat; ISO 14313 (API 6D) standard; class 1500.
Note: Internal diameter (ID) valve shall be define for Project
Engineer.
H10
Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
VE-127
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
18
of
90
TITLE:
Valves Description
TAG
Spec
Description
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 216 Gr WCB; AISI 410 trim; soft/metallic seat;
ISO 14313 (API 6D) standard; class 2500.
VE-148
B3
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 351 Gr CF8M;
AISI 316 trim; metal-metal; ISO 14313 (API 6D) standard;
class 150.
VE-149
B3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
351 Gr CF8M; AISI 316 trim; metal-metal; ISO 14313 (API
6D) standard; class 150.
VE-148
B3
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 351 Gr CF8M;
AISI 316 trim; metal-metal; ISO 14313 (API 6D) standard;
class 150.
VE-149
B3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
351 Gr CF8M; AISI 316 trim; metal-metal; ISO 14313 (API
6D) standard; class 150.
VE-158
B25
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench, 90 degrees rotation; flanged ends ASME B16.5; flat
face (FF); body-trim ASTM A 995 Gr 1B (CD4MCuN); PTFE
reinforced with 25% of carbon seat; ISO 14313 (API 6D)
standard; class 150.
VE-159
B20
Ball valve; full bore; body PVC; wrench; socket weld ends;
trim PVC; PTFE seat; class 150; Sch 80.
VE-160
B21
Ball valve; full bore; body CPVC; wrench; socket weld ends;
trim CPVC; PTFE seat; class 150; Sch 80.
VE-161D
H5 H10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple XXS; body ASTM A 105; AISI 410 trim; soft
seat; ASME B16.34 LTD standard; class 2500.
VE-162D
H10
Ball valve; fire tested; full bore; stainless steel; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple XXS; body ASTM A 105; AISI
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
19
of
90
TITLE:
Valves Description
TAG
Spec
Description
410 trim; soft/metallic seat; ASME B16.34 LTD standard;
class 2500.
VE-168
G12
VE-169
G12
VE-170
G12
VE-171
G12 G12P
VE-172
G12
VE-173
G12
VE-173P
G12P
VE-186D
F11 G11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
20
of
90
TITLE:
Valves Description
TAG
Spec
Description
mounted; wrench (lever) operator; 90 degrees rotation;
flanged ends, ring type joint (RTJ); body ASTM A 105; ASTM
A 182 Gr F 51 (UNS 31803) trim; body-ball organic coated;
PEEK seat; ISO 14313 (API 6D) standard; class 1500.
VE-187
F11 G11
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; ASTM A 995 Gr 4A (UNS J92205) trim; body-ball
organic coated; PEEK seat; ISO 14313 (API 6D) standard;
class 1500.
VE-188
G11
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim;
body-ball organic coated; PEEK seat; ISO 14313 (API 6D)
standard; class 1500.
VE-189
F11
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; ASTM A 995 Gr 4A (UNS J92205) trim; body-ball
organic coated; PEEK seat; ISO 14313 (API 6D) standard;
class 900.
VE-190
F11
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim;
body-ball organic coated; PEEK seat; ISO 14313 (API 6D)
standard; class 900.
VE-191
F11
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim;
body-ball organic coated; PEEK seat; ISO 14313 (API 6D)
standard; class 900.
VE-192
H11
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; ASTM A 182 Gr F 51 (UNS 31803) trim; body-ball
organic coated; PEEK seat; ASME B16.34 LTD standard;
class 2500.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
21
of
90
TITLE:
Valves Description
TAG
VE-193
Spec
C11
Description
Ball valve; full bore; carbon steel, bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF); body ASTM A 105; ASTM A
995 Gr 4A (UNS J92205) trim; body-ball organic coated;
PTFE reinforced with 25% of carbon seat; ISO 14313 (API
6D) standard; class 300.
VE-194
H11
VE-195
C11
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; ASTM A 995 Gr 4A (UNS J92205) trim; body-ball
organic coated; PEEK seat; ISO 14313 (API 6D) standard;
class 2500.
Ball valve; full bore; carbon steel, bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF); body ASTM A 216 Gr WCB;
ASTM A 995 Gr 4A (UNS J92205) trim; body-ball organic
coated; PTFE reinforced with 25% of carbon seat; ISO
14313 (API 6D) standard; class 300.
VE-196
H11
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; lateral wrench operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim;
body-ball organic coated; PEEK seat; ISO 14313 (API 6D)
standard; class 2500.
VE-197
C11
Ball valve; full bore; carbon steel, bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF); body ASTM A
216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim; bodyball organic coated; PTFE reinforced with 25% of carbon
seat; ISO 14313 (API 6D) standard; class 300.
VE-198
E11
Ball valve; full bore; carbon steel, bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, ring type joint (RTJ); body ASTM A 105; ASTM
A 995 Gr 4A (UNS J92205) trim; body-ball organic coated;
PEEK seat; ISO 14313 (API 6D) standard; class 600.
VE-199
E11
Ball valve; full bore; carbon steel, bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, ring type joint (RTJ); body ASTM A 216 Gr
WCB; ASTM A 995 Gr 4A (UNS J92205) trim; body-ball
organic coated; PEEK seat; ISO 14313 (API 6D) standard;
class 600.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
22
of
90
TITLE:
Valves Description
TAG
VE-200
Spec
E11
Description
Ball valve; full bore; carbon steel, bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5, ring type joint (RTJ); body ASTM
A 216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim; bodyball organic coated; PTFE reinforced with 25% of carbon
seat; ISO 14313 (API 6D) standard; class 600.
VE-201
C11
Ball valve; full bore; carbon steel, bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF); body ASTM A 105; ASTM A
182 Gr F 51 (UNS 31803) trim; body-ball organic coated;
PTFE reinforced with 25% of carbon seat; ISO 17292
standard; class 300.
VE-202
E11
Ball valve; full bore; carbon steel, bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, ring type joint (RTJ); body ASTM A 105; ASTM
A 182 Gr F 51 (UNS 31803) trim; body-ball organic coated;
PEEK seat; ISO 17292 standard; class 600.
VE-204
C10
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF), body ASTM A
216 Gr WCB; AISI 410 trim; PTFE reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 300.
VE-205
C11
Ball valve; fire tested; full bore; carbon steel, bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF); body ASTM A
105; ASTM A 182 Gr F 51 (UNS 31803) trim; body-ball
organic coated; PTFE reinforced with 25% of
carbon/metallic seat; ISO 17292 standard; class 300.
VE-206
C11
Ball valve; fire tested; full bore; carbon steel, bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF); body ASTM A
105; ASTM A 995 Gr 4A (UNS J92205) trim; body-ball
organic coated; PTFE reinforced with 25% of
carbon/metallic seat; ISO 14313 (API 6D) standard; class
300.
VE-207
C11
Ball valve; fire tested; full bore; carbon steel, bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF); body ASTM A
216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim; bodyball organic coated; PTFE reinforced with 25% of
carbon/metallic seat; ISO 14313 (API 6D) standard; class
300.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
23
of
90
TITLE:
Valves Description
TAG
Spec
VE-208
C11
Ball valve; fire tested; full bore; carbon steel, bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5, raised face (RF); body
ASTM A 216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205)
trim; body-ball organic coated; PTFE reinforced with 25% of
carbon/metallic seat; ISO 14313 (API 6D) standard; class
300.
VE-209
B16 C16
VE-210
B16
Description
VE-211
B16
VE-211A
B16
VE-212
B16 C16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; floating ball; wrench (lever)
operator, 90 degrees rotation; socket weld ends with nipple
Sch 40S; body-trim ASTM A 182 Gr F51 (UNS S31803);
PTFE reinforced with 25% of carbon / metallic seat; ISO
17292 standard; class 800.
VE-213
B16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; floating ball; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); PTFE reinforced with 25% of carbon / metallic
seat; ISO 14313 (API 6D) standard; class 150.
VE-214
B16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
24
of
90
TITLE:
Valves Description
TAG
Spec
Description
stainless steel; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; flanged ends ASME
B16.5; raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); PTFE reinforced with 25% of carbon / metallic
seat; ISO 14313 (API 6D) standard; class 150.
VE-214A
B16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; flanged ends ASME
B16.47 Sries A; raised face (RF); body-trim ASTM A 995 Gr
4A (UNS J92205); PTFE reinforced with 25% of carbon /
metallic seat; ISO 14313 (API 6D) standard; class 150.
VE-216
C16
VE-217
C16
VE-219
C16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; floating ball; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); PTFE reinforced with 25% of carbon / metallic
seat; ISO 14313 (API 6D) standard; class 300.
VE-220
C16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; flanged ends ASME
B16.5; raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); PTFE reinforced with 25% of carbon / metallic
seat; ISO 14313 (API 6D) standard; class 300.
VE-221
E16
VE-222
E16
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
25
of
90
TITLE:
Valves Description
TAG
Spec
Description
flanged ends ASME B16.5; raised face (RF); body-trim ASTM
A 995 Gr 4A (UNS J92205); Devlon V seat; ISO 14313 (API
6D) standard; class 600.
VE-223
E16
VE-224
E16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; floating ball; wrench (lever)
operator, 90 degrees rotation; socket weld ends with nipple
Sch 40S; body-trim ASTM A 182 Gr F51 (UNS S31803);
Devlon V / metallic seat; ISO 17292 standard; class 800.
VE-225
E16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; floating ball; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); Devlon V / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-226
E16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; flanged ends ASME
B16.5; raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); Devlon V / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-227
G16
Ball valve; full bore; duplex steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple Sch 40S; body-trim ASTM A 182 Gr
F51 (UNS S31803); PEEK seat; ISO 17292 standard; class
1500.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
26
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-228
G16
Ball valve; full bore; duplex steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF); body-trim ASTM
A 995 Gr 4A (UNS J92205); PEEK seat; ISO 14313 (API
6D) standard; class 1500.
VE-229
G16
Ball valve; full bore; duplex steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF); body-trim ASTM
A 995 Gr 4A (UNS J92205); PEEK seat; ISO 14313 (API
6D) standard; class 1500.
VE-230
B3 C3 E3
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 40S; body ASTM A 182 Gr F 316L; AISI
316L trim; PTFE reinforced with 25% of carbon seat; ISO
14313 (API 6D) standard; class 800.
VE-231
B3
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 40S; body ASTM A 182 Gr F 316L; AISI
316L trim; metal-metal; ISO 14313 (API 6D) standard; class
800.
VE-232
G16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5 ring
type joint (RTJ); body-trim ASTM A 995 Gr 4A (UNS J92205);
PEEK / metallic seat; ISO 14313 (API 6D) standard; class
1500.
VE-232P
G16P
Ball valve; piggable; fire tested ISO 10497 (API 607); full
bore; duplex steel; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; flanged ends ASME
B16.5 ring type joint (RTJ); body-trim ASTM A 995 Gr 4A
(UNS J92205); PEEK / metallic seat; ISO 14313 (API 6D)
standard; class 1500.
Note: Internal diameter (ID) valve shall be define for Project
Engineer.
VE-233
E16
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
27
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-234
E16
VE-235
E16
VE-237
F3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple Sch 80S; body ASTM A 182 Gr F 316L;
AISI 316L trim; PEEK seat; ISO 17292 standard; class
1500.
VE-237C
F3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple Sch 40S; body ASTM A 182 Gr F 316L;
AISI 316L trim; Devlon V seat; ISO 17292 standard; class
1500.
VE-238B
G3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple Sch 80S; body ASTM A 182 Gr F 316L;
AISI 316L trim; PEEK seat; ISO 17292 standard; class
1500.
VE-238C
G3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple Sch 160; body ASTM A 182 Gr F 316L;
AISI 316L trim; PEEK seat; ISO 17292 standard; class
1500.
VE-239C
H3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple Sch 160; body ASTM A 182 Gr F 316L;
AISI 316L trim; PEEK seat; ISO 17292 standard; class
2500.
VE-239D
H3
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
28
of
90
TITLE:
Valves Description
TAG
VE-240
Spec
B3
Description
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 40S; body ASTM A 182 Gr F 316L; AISI
316L trim; PEEK seat; ISO 14313 (API 6D) standard; class
800.
VE-241
B3
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 351 Gr CF8M;
AISI 316 trim; PEEK seat; ISO 14313 (API 6D) standard;
class 150.
VE-242
B3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
351 Gr CF8M; AISI 316 trim; PEEK seat; ISO 14313 (API
6D) standard; class 150.
VE-243
B3
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 40S; body ASTM A 182 Gr F 316L; AISI
316L trim; TFE/P seat; ISO 14313 (API 6D) standard; class
800.
VE-244
B3
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 351 Gr CF8M;
AISI 316 trim; TFE/P seat; ISO 14313 (API 6D) standard;
class 150.
VE-245
B3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
351 Gr CF8M; AISI 316 trim; TFE/P seat; ISO 14313 (API
6D) standard; class 150.
VE-246
B3 C3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 40S; body
ASTM A 182 Gr F 316L; AISI 316L trim; PTFE reinforced
with 25% of carbon / metallic seat; ISO 14313 (API 6D)
standard; class 800.
VE-247
B3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 351 Gr CF8M; AISI 316 trim; PTFE
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 150.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
29
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-248
B3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 351 Gr CF8M; AISI 316 trim;
PTFE reinforced with 25% of carbon / metallic seat; ISO
14313 (API 6D) standard; class 150.
VE-249
B3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 40S; body
ASTM A 182 Gr F 316L; AISI 316L trim; PEEK / metallic
seat; ISO 14313 (API 6D) standard; class 800.
VE-250
B3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 351 Gr CF8M; AISI 316 trim; PEEK /
metallic seat; ISO 14313 (API 6D) standard; class 150.
VE-251
B3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 351 Gr CF8M; AISI 316 trim;
PEEK / metallic seat; ISO 14313 (API 6D) standard; class
150.
VE-252
C10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 216 Gr WCB; AISI 410 trim;
PTFE reinforced with 25% of carbon seat; ISO 14313 (API
6D) standard; class 300.
VE-255
B3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 40S; body
ASTM A 182 Gr F 316L; AISI 316L trim; TFE/P / metallic
seat; ISO 14313 (API 6D) standard; class 800.
VE-256
B3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 351 Gr CF8M; AISI 316 trim; TFE/P /
metallic seat; ISO 14313 (API 6D) standard; class 150.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
30
of
90
TITLE:
Valves Description
TAG
VE-257
Spec
B3
Description
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 351 Gr CF8M; AISI 316 trim;
TFE/P / metallic seat; ISO 14313 (API 6D) standard; class
150.
VE-259
C3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5, raised face
(RF); body ASTM A 351 CF8M; AISI 316 trim; PTFE
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 300.
VE-260
C3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5,
raised face (RF); body ASTM A 351 CF8M; AISI 316 trim;
PTFE reinforced with 25% of carbon / metallic seat; ISO
14313 (API 6D) standard; class 300.
VE-261
E3
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 40S; body ASTM A 182 Gr F 316;L AISI
316L trim; PEEK seat; ISO 14313 (API 6D) standard; class
800.
VE-262
E3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; PEEK seat; ISO 14313 (API
6D) standard; class 600.
VE-263
E3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; PEEK seat; ISO 14313 (API
6D) standard; class 600.
VE-264
E3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 40S; body
ASTM A 182 Gr F 316L; AISI 316L trim; Devlon V / metallic
seat; ISO 17292 standard; class 800.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
31
of
90
TITLE:
Valves Description
TAG
VE-265
Spec
E3
Description
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 351 Gr CF8M;
AISI 316 trim; Devlon V / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-266
E3
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 351 Gr CF8M;
AISI 316 trim; Devlon V / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-267
E3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 40S; body
ASTM A 182 Gr F 316L; AISI 316L trim; PEEK / metallic
seat; ISO 17292 standard; class 800.
VE-268
E3
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 351 Gr CF8M;
AISI 316 trim; PEEK / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-269
E3
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 351 Gr CF8M;
AISI 316 trim; PEEK / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-270
F3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple Sch 40S; body ASTM A 182 Gr F 316L;
AISI 316L trim; PEEK seat; ISO 17292 standard; class
1500.
VE-270B
F3
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
32
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-271
C10
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF), body ASTM A 105; AISI 410
trim; PTFE reinforced with 25% of carbon seat; ISO 14313
(API 6D) stanrad; class 300.
VE-272
F3
Ball valve; full bore; stainless stell; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; PEEK seat; ISO 14313 (API
6D) standard; class 1500.
VE-273
F3
Ball valve; full bore; stainless stell; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; PEEK seat; ISO 14313 (API
6D) standard; class 900.
VE-274
F3
Ball valve; full bore; stainless stell; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; PEEK seat; ISO 14313 (API
6D) standard; class 900.
VE-275
F3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; socket weld ends with nipple Sch 40S;
body ASTM A 182 Gr F 316L; AISI 316L trim; Devlon V /
metallic seat; ISO 17292 standard; class 1500.
VE-275B
F3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; socket weld ends with nipple Sch 80S;
body ASTM A 182 Gr F 316L; AISI 316L trim; Devlon V /
metallic seat; ISO 17292 standard; class 1500.
VE-276
C10
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF), body ASTM A 216 Gr WCB;
AISI 410 trim; PTFE reinforced with 25% of carbon seat;
ISO 14313 (API 6D) stanrad; class 300.
VE-277
F3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5; ring type joint
(RTJ); body ASTM A 351 Gr CF8M; AISI 316 trim; Devlon V
/ metallic seat; ISO 14313 (API 6D) standard; class 900.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
33
of
90
TITLE:
Valves Description
TAG
VE-278
Spec
F3
Description
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5; ring type joint
(RTJ); body ASTM A 351 Gr CF8M; AISI 316 trim; Devlon V
/ metallic seat; ISO 14313 (API 6D) standard; class 900.
VE-279
F3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 351 Gr CF8M; AISI 316 trim;
Devlon V / metallic seat; ISO 14313 (API 6D) standard;
class 900.
VE-280
F3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; socket weld ends with nipple Sch 40S;
body ASTM A 182 Gr F 316L; AISI 316L trim; PEEK /
metallic seat; ISO 17292 standard; class 1500.
VE-280B
F3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; socket weld ends with nipple Sch 80S;
body ASTM A 182 Gr F 316L; AISI 316L trim; PEEK /
metallic seat; ISO 17292 standard; class 1500.
VE-282
F3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5; ring type joint
(RTJ); body ASTM A 351 Gr CF8M; AISI 316 trim; PEEK /
metallic seat; ISO 14313 (API 6D) standard; class 900.
VE-283
F3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 351 Gr CF8M; AISI 316 trim;
PEEK / metallic seat; ISO 14313 (API 6D) standard; class
900.
VE-284
F3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 351 Gr CF8M; AISI 316
trim; PEEK / metallic seat; ISO 14313 (API 6D) standard;
class 900.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
34
of
90
TITLE:
Valves Description
TAG
VE-285B
Spec
G3
Description
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; socket weld ends with nipple
Sch 80S; body ASTM A 182 Gr 316L; AISI 316L trim; PEEK
/ metallic seat; ISO 17292 standard; class 2500.
VE-285C
G3
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; socket weld ends with nipple
Sch 160; body ASTM A 182 Gr 316L; AISI 316L trim; PEEK
/ metallic seat; ISO 17292 standard; class 2500.
VE-287
G3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 351 Gr CF8M; AISI 316 trim;
PEEK / metallic seat; ISO 14313 (API 6D) standard; class
1500.
VE-288
G3
Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 351 Gr CF8M; AISI 316
trim; PEEK / metallic seat; ISO 14313 (API 6D) standard;
class 1500.
VE-289C
H3
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; socket weld ends with nipple
Sch 160; body ASTM A 182 Gr 316L; AISI 316L trim; PEEK
/ metallic seat; ISO 17292 standard; class 2500.
VE-289D
H3
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5,
raised face (RF); body ASTM A 182 Gr 316L; AISI 316L trim;
PEEK / metallic seat; ISO 17292 standard; class 2500.
VE-290
E3
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 40S; body ASTM A 182 Gr F 316L; AISI
316L trim; Devlon V seat; ISO 17292 standard; class 800.
VE-291
H3
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench
(lever) operator, 90 degrees rotation; socket weld ends with
nipple XXS; body ASTM A 182 Gr 316L; AISI 316L trim;
PEEK / metallic seat; ISO 17292 standard; class 2500.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
35
of
90
TITLE:
Valves Description
TAG
VE-292
Spec
H3
Description
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; socket weld ends with
nipple XXS; body ASTM A 182 Gr 316L; AISI 316L trim;
PEEK / metallic seat; ISO 17292 standard; class 2500.
VE-293
E16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; floating ball; wrench (lever)
operator, 90 degrees rotation; socket weld ends with nipple
Sch 40S; body-trim ASTM A 182 Gr F51 (UNS S31803);
TFE/P / metallic seat; ISO 17292 standard; class 800.
VE-294
E16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; floating ball; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); TFE/P / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-295
E16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; flanged ends ASME
B16.5; raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); TFE/P / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-296B
B6 B19
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 350 Gr LF2 CL 1;
AISI 304 trim; PEEK seat; ISO 14313 (API 6D) standard;
class 800.
VE-296C
B6 B19
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 350 Gr LF2 CL 1;
AISI 304 trim; PEEK seat; ISO 14313 (API 6D) standard;
class 800.
VE-297
B6 B19
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 352 Gr LCB;
AISI 304 trim; PEEK seat; ISO 14313 (API 6D) standard;
class 150.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
36
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-298
B6 B19
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
352 Gr LCB; AISI 304 trim; PEEK seat; ISO 14313 (API 6D)
standard; class 150.
VE-298A
B6 B19
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series; raised face (RF); body
ASTM A 352 Gr LCB; AISI 304 trim; PEEK seat; ISO 14313
(API 6D) standard; class 150.
VE-299B
B6 B19
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 350 Gr LF2 CL 1; AISI 304 trim; PTFE reinforced
with 25% of carbon / metallic seat; ISO 14313 (API 6D)
standard; class 800.
VE-299C
B6 B19
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 350 Gr LF2 CL 1; AISI 304 trim; PTFE reinforced
with 25% of carbon / metallic seat; ISO 14313 (API 6D)
standard; class 800.
VE-300
B6 B19
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 352 Gr LCB; AISI 304 trim; PTFE
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 150.
VE-301
B6 B19
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 352 Gr LCB; AISI 304 trim;
PTFE reinforced with 25% of carbon / metallic seat; ISO
14313 (API 6D) standard; class 150.
VE-301A
B6 B19
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.47
Series; raised face (RF); body ASTM A 352 Gr LCB; AISI 304
trim; PTFE reinforced with 25% of carbon / metallic seat;
ISO 14313 (API 6D) standard; class 150.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
37
of
90
TITLE:
Valves Description
TAG
VE-302B
Spec
B6 B19
Description
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 350 Gr LF2 CL 1; AISI 304 trim; PEEK / metallic
seat; ISO 14313 (API 6D) standard; class 800.
VE-302C
B6 B19
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 350 Gr LF2 CL 1; AISI 304 trim; PEEK / metallic
seat; ISO 14313 (API 6D) standard; class 800.
VE-303
B6 B19
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 352 Gr LCB; AISI 304 trim; PEEK /
metallic seat; ISO 14313 (API 6D) standard; class 150.
VE-304
B6 B19
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 352 Gr LCB; AISI 304 trim;
PEEK / metallic seat; ISO 14313 (API 6D) standard; class
150.
VE-304A
B6 B19
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.47
Series A; raised face (RF); body ASTM A 352 Gr LCB; AISI
304 trim; PEEK / metallic seat; ISO 14313 (API 6D)
standard; class 150.
VE-305B
B9 B10 C9 Ball valve; full bore; carbon steel; bolted body; floating ball;
C10
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 105; AISI 410 trim;
PEEK seat; ISO 17292 standard; class 800.
VE-305D
B9 C9
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch XXS; body ASTM A 105; AISI 410 trim;
PEEK seat; ISO 17292 standard; class 800.
VE-306
B9 B10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; AISI 410
trim; PEEK seat; ISO 14313 (API 6D) standard; class 150.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
38
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-307
B9 B10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; PEEK seat; ISO 14313 (API 6D) standard;
class 150.
VE-308
B9 B10
Ball valve; full bore; carbon steel; bolted body; floating ball;
handwheel gear operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; PEEK seat; ISO 14313 (API 6D) standard;
class 150.
VE-308A
B9 B10
Ball valve; full bore; carbon steel; bolted body; floating ball;
handwheel gear operator, 90 degrees rotation; flanged ends
ASME B16.47 Series A; raised face (RF); body ASTM A 216
Gr WCB; AISI 410 trim; PEEK seat; ISO 14313 (API 6D)
standard; class 150.
VE-309B
B9 B10 C9 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
C10
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; AISI 410 trim; PEEK / metallic seat; ISO
17292 standard; class 800.
VE-309D
B9 B10 C9 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; AISI 410 trim; PEEK / metallic seat; ISO
17292 standard; class 800.
VE-310
B9 B10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5 raised face (RF);
body ASTM A 105; AISI 410 trim; PEEK / metallic seat; ISO
14313 (API 6D) standard; class 150.
VE-311
B9 B10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5 raised face (RF);
body ASTM A 216 Gr WCB; AISI 410 trim; PEEK / metallic
seat; ISO 14313 (API 6D) standard; class 150.
VE-312
B9 B10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5
raised face (RF); body ASTM A 216 Gr WCB; AISI 410 trim;
PEEK / metallic seat; ISO 17292 standard; class 150.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
39
of
90
TITLE:
Valves Description
TAG
VE-312A
Spec
B9 B10
Description
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.47
Series A raised face (RF); body ASTM A 216 Gr WCB; AISI
410 trim; PEEK / metallic seat; ISO 14313 (API 6D)
standard; class 150.
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
PEEK seat; ISO 17292 standard; class 800.
VE-313C
B10
VE-314
C3
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF); body ASTM A 351 CF8M;
AISI 316 trim; PTFE reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 300.
VE-315
C3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF); body ASTM A
351 CF8M; AISI 316 trim; PTFE reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 300.
VE-316
C9 C10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF); body ASTM A 105; AISI 410
trim; PTFE reinforced with 25% of carbon seat; ISO 14313
(API 6D) standard; class 300.
VE-317C
B10 C10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 105; AISI 410 trim; PEEK / metallic seat; ISO
17292 standard; class 800.
VE-318
C9 C10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; PTFE reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 300.
VE-319
C9 C10
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF); body ASTM A
216 Gr WCB; AISI 410 trim; PTFE reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 300.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
40
of
90
TITLE:
Valves Description
TAG
VE-321B
Spec
C10
Description
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
PEEK seat; ISO 17292 standard; class 800.
VE-321C
C10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 105; AISI 410 trim;
PEEK seat; ISO 17292 standard; class 800.
VE-322
C10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; AISI 410
trim; PEEK seat; ISO 14313 (API 6D) standard; class 300.
VE-323
C10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; PEEK seat; ISO 14313 (API 6D) standard;
class 300.
VE-324
C10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB; AISI 410 trim; PEEK seat; ISO 14313 (API
6D) standard; class 300.
VE-325B
C10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 105; AISI 410 trim; PTFE reinforced with 25% of
carbon / metallic seat; ISO 17292 standard; class 800.
VE-325C
C10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; AISI 410 trim; PTFE reinforced with 25% of
carbon / metallic seat; ISO 17292 standard; class 800.
VE-326
C10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 105; AISI 410 trim; PTFE reinforced
with 25% of carbon / metallic seat; ISO 14313 (API 6D)
standard; class 300.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
41
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-327
C10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 216 Gr WCB; AISI 410 trim; PTFE
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 300.
VE-328
B3
Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 351 Gr CF8M;
AISI 316 trim; PTFE reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 150.
VE-329
B3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
351 Gr CF8M; AISI 316 trim; PTFE reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 150.
VE-330B
B6 B19
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 350 Gr LF2 CL 1;
AISI 304 trim; PTFE reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 800.
VE-330C
B6 B19
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 350 Gr LF2 CL 1;
AISI 304 trim; PTFE reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 800.
VE-331
B6 B19
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 352 Gr LCB;
AISI 304 trim; PTFE reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 150.
VE-332
B6 B19
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
352 Gr LCB; AISI 304 trim; PTFE reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 150.
VE-332A
B6 B19
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series; raised face (RF); body
ASTM A 352 Gr LCB; AISI 304 trim; PTFE reinforced with
25% of carbon seat; ISO 14313 (API 6D) standard; class 150.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
42
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-333B
B9 B10 C9 Ball valve; full bore; carbon steel; bolted body; floating ball;
C10
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 105; AISI 410 trim;
PTFE reinforced with 25% of carbon seat; ISO 17292
standard; class 800.
VE-333D
B9 B17 C9 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch XXS; body ASTM A 105; AISI 410 trim;
PTFE reinforced with 25% of carbon seat; ISO 17292
standard; class 800.
VE-334
B9 B10 B17 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; AISI 410
trim; PTFE reinforced with 25% of carbon seat; ISO 14313
(API 6D) standard; class 150.
VE-335
B9 B10 B17 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; PTFE reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 150.
VE-336
B9 B10 B17 Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB; AISI 410 trim; PTFE reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 150.
VE-336A
VE-337B
B9 B10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; raised face (RF); body
ASTM A 216 Gr WCB; AISI 410 trim; PTFE reinforced with
25% of carbon seat; ISO 14313 (API 6D) standard; class
150.
B9 B10 C9 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
C10
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; AISI 410 trim; PTFE reinforced with 25% of
carbon / metallic seat; ISO 17292 standard; class 800.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
43
of
90
TITLE:
Valves Description
TAG
VE-337D
VE-338
Spec
Description
B9 B10 B17 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
C9
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple XXS; body
ASTM A 105; AISI 410 trim; PTFE reinforced with 25% of
carbon / metallic seat; ISO 17292 standard; class 800.
B9 B10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 105; AISI 410 trim; PTFE reinforced
with 25% of carbon / metallic seat; ISO 14313 (API 6D)
standard; class 150.
VE-339
B9 B10 B17 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 216 Gr WCB; AISI 410 trim; PTFE
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 150.
VE-340
B9 B10 B17 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 216 Gr WCB; AISI 410 trim;
PTFE reinforced with 25% of carbon / metallic seat; ISO
14313 (API 6D) standard; class 150.
VE-340A
B9 B10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator; flanged ends ASME B16.47 Series A; raised face
(RF); body ASTM A 216 Gr WCB; AISI 410 trim; PTFE
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 150.
VE-341C
B10 C10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
PTFE reinforced with 25% of carbon seat; ISO 17292
standard; class 800.
VE-342C
B10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 105; AISI 410 trim; PTFE reinforced with 25% of
carbon / metallic seat; ISO 17292 standard; class 800.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
44
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-343
C9 C10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; AISI 410
trim; PEEK seat; ISO 14313 (API 6D) standard; class 300.
VE-344
C9 C10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; PEEK seat; ISO 14313 (API 6D) standard;
class 300.
VE-346B
B11
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; ASTM A
182 Gr F 51 (UNS 31803) trim; body-trim organic coating;
PTFE reinforced with 25% of carbon seat; ISO 17292
standard; class 150.
VE-347
B11
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; ASTM A
995 Gr 4A (UNS J92205) trim; body-trim organic coating;
PTFE reinforced with 25% of carbon seat; ISO 14313 (API
6D) standard; class 150.
VE-348
B11
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
ASTM A 995 Gr 4A (UNS J92205) trim; body-trim organic
coating; PTFE reinforced with 25% of carbon seat; ISO
14313 (API 6D) standard; class 150.
VE-349
B11
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim; bodytrim organic coating; PTFE reinforced with 25% of carbon
seat; ISO 14313 (API 6D) standard; class 150.
VE-349A
B11
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; raised face (RF); body
ASTM A 216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205)
trim; body-trim organic coating; PTFE reinforced with 25%
of carbon seat; ISO 14313 (API 6D) standard; class 150.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
45
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-350B
B11
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face (RF);
body ASTM A 105; ASTM A 182 Gr F 51 (UNS 31803) trim;
body-trim organic coating; PTFE reinforced with 25% of
carbon / metallic seat; ISO 17292 standard; class 150.
VE-351
B11
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 105; ASTM A 995 Gr 4A (UNS J92205)
trim; body-trim organic coating; PTFE reinforced with 25%
of carbon / metallic seat; ISO 14313 (API 6D) standard; class
150.
VE-352
B11
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 216 Gr WCB; ASTM A 995 Gr 4A (UNS
J92205) trim; body-trim organic coating; PTFE reinforced
with 25% of carbon / metallic seat; ISO 14313 (API 6D)
standard; class 150.
VE-353
B11
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 216 Gr WCB; ASTM A 995
Gr 4A (UNS J92205) trim; body-trim organic coating; PTFE
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 150.
VE-353A
B11
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.47
Series A; raised face (RF); body ASTM A 216 Gr WCB;
ASTM A 995 Gr 4A (UNS J92205) trim; body-trim organic
coating; PTFE reinforced with 25% of carbon / metallic
seat; ISO 14313 (API 6D) standard; class 150.
VE-354
B12 C12
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
46
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-355
B12
VE-356
B12
VE-356A
B12
VE-357
C9 C10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB; AISI 410 trim; PEEK seat; ISO 14313 (API
6D) standard; class 300.
VE-358
C9 C10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 105; AISI 410 trim; PTFE reinforced
with 25% of carbon / metallic seat; ISO 14313 (API 6D)
standard; class 300.
VE-359
C9 C10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 216 Gr WCB; AISI 410 trim; PTFE
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 300.
VE-360
C9 C10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 216 Gr WCB; AISI 410 trim;
PTFE reinforced with 25% of carbon / metallic seat; ISO
14313 (API 6D) standard; class 300.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
47
of
90
TITLE:
Valves Description
TAG
VE-361
Spec
C9 C10
Description
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 105; AISI 410 trim; PEEK / metallic
seat; ISO 14313 (API 6D) standard; class 300.
VE-362
C9 C10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 216 Gr WCB; AISI 410 trim; PEEK /
metallic seat; ISO 14313 (API 6D) standard; class 300.
VE-363
C9 C10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 216 Gr WCB; AISI 410 trim;
PEEK / metallic seat; ISO 14313 (API 6D) standard; class
300.
VE-364
B12 C12
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel superduplex; bolted body; floating ball; wrench
(lever) operator, 90 degrees rotation; socket weld ends with
nipple Sch 40S; body-trim ASTM A 182 Gr F55 (UNS
S32760); PTFE reinforced with 25% of carbon / metallic
seat; ISO 17292 standard; class 800.
VE-365
B12
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel superduplex; bolted body; floating ball; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5; raised face (RF); body-trim ASTM A 995 Gr 5A (UNS
J93404); PTFE reinforced with 25% of carbon / metallic
seat; ISO 14313 (API 6D) standard; class 150.
VE-366
B12
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel superduplex; bolted body; trunnion-mounted;
handwheel gear operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body-trim ASTM A 995 Gr 5A
(UNS J93404); PTFE reinforced with 25% of carbon /
metallic seat; ISO 14313 (API 6D) standard; class 150.
VE-366A
B12
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel superduplex; bolted body; trunnion-mounted;
handwheel gear operator, 90 degrees rotation; flanged ends
ASME B16.47 Series A; raised face (RF); body-trim ASTM A
995 Gr 5A (UNS J93404); PTFE reinforced with 25% of
carbon / metallic seat; ISO 14313 (API 6D) standard; class
150.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
48
of
90
TITLE:
Valves Description
TAG
VE-367
Spec
C12
Description
Ball valve; full bore; stainless steel superduplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; raised face (RF); bodytrim ASTM A 995 Gr 5A (UNS J93404); PTFE reinforced
with 25% of carbon seat; ISO 14313 (API 6D) standard; class
300.
VE-368
C12
VE-369
C12
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel superduplex; bolted body; floating ball; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5; raised face (RF); body-trim ASTM A 995 Gr 5A (UNS
J93404); PTFE reinforced with 25% of carbon / metallic
seat; ISO 14313 (API 6D) standard; class 300.
VE-370
C12
Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel superduplex; bolted body; trunnion-mounted;
handwheel gear operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body-trim ASTM A 995 Gr 5A
(UNS J93404); PTFE reinforced with 25% of carbon /
metallic seat; ISO 14313 (API 6D) standard; class 300.
VE-371
E3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; Devlon V seat; ISO 14313
(API 6D) standard; class 600.
VE-372
E3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; Devlon V seat; ISO 14313
(API 6D) standard; class 600.
VE-373D
E9
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple XXS; body ASTM A 105; AISI 410 trim;
Devlon V seat; ISO 17292 standard; class 800.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
49
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-374
E9 E10 E17 Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; Devlon V seat; ISO 14313 (API 6D)
standard; class 600.
VE-375
E9 E10 E17 Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; Devlon V seat; ISO 14313
(API 6D) standard; class 600.
VE-376
E9 E10 E17 Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; Devlon V seat; ISO 14313
(API 6D) standard; class 600.
VE-377D
E9
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple XXS; body
ASTM A 105; AISI 410 trim; Devlon V / metallic seat; ISO
17292 standard; class 800.
VE-378
E9 E10 E17 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
Devlon V / metallic seat; ISO 14313 (API 6D) standard;
class 600.
VE-379
E9 E10 E17 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; Devlon V / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-380
E9 E10 E17 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; Devlon V metallic seat; ISO 14313 (API 6D) standard;
class 600.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
50
of
90
TITLE:
Valves Description
TAG
VE-381B
Spec
E10
Description
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with niple Sch 80; body ASTM A 105; AISI 410 trim;
Devlon V seat; ISO 17292 standard; class 800.
VE-381C
E10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with niple Sch 160; body ASTM A 105; AISI 410 trim;
Devlon V seat; ISO 17292 standard; class 800.
VE-382B
E10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with niple Sch 80; body ASTM A 105; AISI 410 trim;
PEEK seat; ISO 17292 standard; class 800.
VE-382C
E10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with niple Sch 160; body ASTM A 105; AISI 410 trim;
PEEK seat; ISO 17292 standard; class 800.
VE-383
E10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; PEEK seat; ISO 14313 (API 6D)
standard; class 600.
VE-384
E10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; PEEK seat; ISO 14313 (API
6D) standard; class 600.
VE-385
E10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; PEEK seat; ISO 14313 (API
6D) standard; class 600.
VE-387
B16
VE-388
B16
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
51
of
90
TITLE:
Valves Description
TAG
Spec
VE-389
B16
B16
VE-390
B16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; floating ball; wrench (lever)
operator, 90 degrees rotation; socket weld ends with nipple
Sch 40S; body-trim ASTM A 182 Gr F51 (UNS S31803);
TFE/P / metallic seat; ISO 17292 standard; class 800.
VE-391
B16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; floating ball; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); TFE/P / metallic seat; ISO 14313 (API 6D) standard;
class 150.
VE-392
B16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; flanged ends ASME
B16.5; raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); TFE/P / metallic seat; ISO 14313 (API 6D) standard;
class 150.
VE-392A
B16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
stainless steel; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; flanged ends ASME
B16.47 Sries A; raised face (RF); body-ball ASTM A 995 Gr
4A (UNS J92205); TFE/P / metallic seat; ISO 14313 (API 6D)
standard; class 150.
VE-393B
E10 E17
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; Devlon V / metallic seat; ISO 17292 standard;
class 800.
VE-389A
Description
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
52
of
90
TITLE:
Valves Description
TAG
VE-393C
Spec
E10
Description
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 105; Devlon V / metallic seat; ISO 17292 standard;
class 800.
VE-394
G10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5,
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; PEEK / metallic seat; ISO 17292 standard; class 1500.
VE-397B
E10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with niple Sch 80; body
ASTM A 105; AISI 410 trim; PEEK / metallic seat; ISO
17292 standard; class 800.
VE-397C
E10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with niple Sch 160; body
ASTM A 105; AISI 410 trim; PEEK / metallic seat; ISO
17292 standard; class 800.
VE-398
E10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
PEEK / metallic seat; ISO 14313 (API 6D) standard; class
600.
VE-399
E10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; PEEK / metallic seat; ISO 14313 (API 6D) standard;
class 600.
VE-400
E10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; PEEK / metallic seat; ISO 14313 (API 6D) standard;
class 600.
VE-401B
E10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with niple Sch 80; body ASTM A 105; AISI 410 trim;
TFE/P seat; ISO 17292 standard; class 800.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
53
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-401C
E10
VE-402
E10
VE-403
E10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; TFE/P seat; ISO 14313 (API
6D) standard; class 600.
VE-404
E10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; TFE/P seat; ISO 14313 (API
6D) standard; class 600.
VE-405B
E10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with niple Sch 80; body
ASTM A 105; AISI 410 trim; TFE/P / metallic seat; ISO
17292 standard; class 800.
VE-405C
E10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with niple Sch 160; body
ASTM A 105; AISI 410 trim; TFE/P / metallic seat; ISO
17292 standard; class 800.
VE-406
E10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
TFE/P / metallic seat; ISO 14313 (API 6D) standard; class
600.
VE-407
E10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; TFE/P / metallic seat; ISO 14313 (API 6D) standard;
class 600.
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with niple Sch 160; body ASTM A 105; AISI 410 trim;
TFE/P / metallic seat; ISO 17292 standard; class 800.
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
TFE/P seat; ISO 14313 (API 6D) standard; class 600.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
54
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-408
E10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; TFE/P / metallic seat; ISO 14313 (API 6D) standard;
class 600.
VE-409
F3
Ball valve; full bore; stainless stell; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; Devlon V seat; ISO 14313
(API 6D) standard; class 1500.
VE-410
F3
Ball valve; full bore; stainless stell; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; Devlon V seat; ISO 14313
(API 6D) standard; class 900.
VE-411
F3
Ball valve; full bore; stainless stell; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; Devlon V seat; ISO 14313
(API 6D) standard; class 900.
VE-412
G19
Ball valve; fire tested; full bore; carbon steel; bolted body;
trennion assembly; wrench (lever) operator, 90 degrees
rotation; socket weld ends with nipple XXS; body ASTM A
350 Gr LF2 CL1; AISI 304 trim; soft/metallic seat; ASME
B16.34 / ISO 10497 standard; class 1500.
VE-413
G19
Ball valve; fire tested, full bore; carbon steel; bolted body;
trunnion-mounted; wrench (lever) operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 352 Gr LCB; AISI 304 trim; soft/metallic; ISO
14313 (API 6D) / ISO 10497 standard; class 1500.
VE-414
G19
Ball valve; fire tested, full bore; carbon steel; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 352 Gr LCB; AISI 304 trim; soft/metallic; ISO
14313 (API 6D) / ISO 10497 standard; class 1500.
VE-415B
F10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 105; AISI 410 trim;
Devlon V seat; ASME B16.34 LTD standard; class 1500.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
55
of
90
TITLE:
Valves Description
TAG
VE-415C
Spec
F10
Description
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
Devlon V seat; ASME B16.34 LTD standard; class 1500.
VE-416
F10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; Devlon V seat; ISO 14313 (API 6D)
standard; class 1500.
VE-417
F10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; Devlon V seat; ISO 14313 (API 6D)
standard; class 900.
VE-418
F10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; Devlon V seat; ISO 14313
(API 6D) standard; class 900.
VE-419
F10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; Devlon V seat; ISO 14313
(API 6D) standard; class 900.
VE-420B
F10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 105; AISI 410 trim;
PEEK seat; ASME B16.34 LTD standard; class 1500.
VE-420C
F10
Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
PEEK seat; ASME B16.34 LTD standard; class 1500.
VE-421
F10 G10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; PEEK seat; ISO 14313 (API 6D)
standard; class 1500.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
56
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-422
F10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; PEEK seat; ISO 14313 (API 6D)
standard; class 900.
VE-423
F10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; PEEK seat; ISO 14313 (API
6D) standard; class 900.
VE-424
F10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; PEEK seat; ISO 14313 (API
6D) standard; class 900.
VE-425B
F10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; AISI 410 trim; Devlon V / metallic seat; ASME
B16.34 LTD standard; class 1500.
VE-425C
F10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 105; AISI 410 trim; Devlon V / metallic seat; ASME
B16.34 LTD standard; class 1500.
VE-426
F10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
Devlon V / metallic seat; ISO 14313 (API 6D) standard;
class 1500.
VE-427
F10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
Devlon V / metallic seat; ISO 14313 (API 6D) standard;
class 900.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
57
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-428
F10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; Devlon V / metallic seat; ISO 14313 (API 6D)
standard; class 900.
VE-429
F10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; Devlon V / metallic seat; ISO 14313 (API 6D)
standard; class 900.
VE-430B
F10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; AISI 410 trim; PEEK / metallic seat; ASME
B16.34 LTD standard; class 1500.
VE-430C
F10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 105; AISI 410 trim; PEEK / metallic seat; ASME
B16.34 LTD standard; class 1500.
VE-431
F10 G10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
PEEK / metallic seat; ISO 14313 (API 6D) standard; class
1500.
VE-432
F10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
PEEK / metallic seat; ISO 14313 (API 6D) standard; class
900.
VE-433
F10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; PEEK / metallic seat; ISO 14313 (API 6D) standard;
class 900.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
58
of
90
TITLE:
Valves Description
TAG
VE-434
Spec
F10
Description
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; PEEK / metallic seat; ISO 14313 (API 6D) standard;
class 900.
VE-435
G3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 182 Gr F316; AISI 316 trim; PEEK seat; ISO 14313 (API
6D) standard; class 1500.
VE-436
G3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 182 Gr F316; AISI 316 trim; PEEK seat; ISO 14313 (API
6D) standard; class 1500.
VE-437D
G10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple Sch XXS; body ASTM A 105;
AISI 410 trim; PEEK seat; ASME B16.34 LTD standard;
class 1500.
VE-438
G10
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; PEEK seat; ISO 14313 (API
6D) standard; class 1500.
VE-439D
G10
Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; socket weld ends with nipple
Sch XXS; body ASTM A 105; AISI 410 trim; PEEK / metallic
seat; ASME B16.34 LTD standard; class 1500.
VE-440
G16 G16P
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
steel; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; socket weld ends with nipple Sch 40S;
body-trim ASTM A 182 Gr F51 (UNS S31803); PEEK /
metallic seat; ISO 17292 standard; class 1500.
VE-441
G16
Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
steel; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5, ring type joint
(RTJ); body-trim ASTM A 995 Gr 4A (UNS J92205); PEEK /
metallic seat; ISO 14313 (API 6D) standard; class 1500.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
59
of
90
TITLE:
Valves Description
TAG
VE-441P
Spec
G16P
Description
Ball valve; piggable; fire tested ISO 10497 (API 607); full
bore; duplex steel; bolted body; trunnion-mounted; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5, ring type joint (RTJ); body-trim ASTM A 995 Gr 4A
(UNS J92205); PEEK / metallic seat; ISO 14313 (API 6D)
standard; class 1500.
Note: Internal diameter (ID) valve shall be defined for Project
Engineer.
VE-442
H3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5, ring type joint (RTJ); body ASTM
A 351 CF8M; AISI 316 trim; PEEK seat; ISO 14313 (API
6D) standard; class 2500.
VE-443
H3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5, ring type joint (RTJ); body ASTM
A 351 CF8M; AISI 316 trim; PEEK seat; ISO 14313 (API
6D) standard; class 2500.
VE-450
H14 H30
H30P
Ball valve; fire tested; full bore; carbon steel with Inconel
625; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A105; AISI 410 trim; PEEK metal
seat; class 2500.
VE-451
H30
Ball valve; fire tested; full bore; carbon steel with Inconel
625; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A105; AISI 410 trim; metal-metal;
class 2500.
VE-452
H30
Ball valve; fire tested; full bore; carbon steel with Inconel
625; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A105; AISI 410 trim; metal-metal;
class 2500.
VE-452P
H30P
Ball valve; piggable; fire tested; full bore; carbon steel with
Inconel 625; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A105; AISI 410 trim; metalmetal; class 2500. Note: Internal diameter (ID) valve shall be
defined for Project Engineer.
Ball valve; full bore; carbon steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
buttweld ends ASME B16.25; body ASTM A 105; AISI 410
trim; PEEK seat; ASME B16.34 standard; class 2500.
VE-458
H14
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
60
of
90
TITLE:
Valves Description
TAG
Spec
Description
VE-459
E30
Ball valve; fire tested; full bore; carbon steel with Inconel
625; bolted body; trunnion-mounted; wrench (lever) operator
90 degrees rotation; ends ASME B16.5; ring joint face (RTJ);
body ASTM A 105; AISI 410 trim; RPTFE/Metal seat; class
600.
VE-460
E30
Ball valve; fire tested; full bore; carbon steel with Inconel
625; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; ends ASME B16.5; ring joint face (RTJ);
body ASTM A 105; AISI 410 trim; RPTFE/Metal seat; class
600.
VE-461
E30
Ball valve; fire tested; full bore; carbon steel with Inconel
625; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; ends ASME B16.5; ring joint face (RTJ);
body ASTM A 216 WCB; AISI 410 trim; RPTFE/Metal seat;
class 600.
VE-462
E30
Ball valve; fire tested; full bore; carbon steel with Inconel
625;
bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; ends ASME B16.5; ring joint
face (RTJ);
body ASTM A 216 WCB; AISI 410 trim;
RPTFE/Metal seat; class 600.
VE-463
C30
Ball valve; fire tested; full bore; Inconel 625 alloy steel;
bolted body; trunnion-mounted; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM B 564 (UNS N06625); AISI 410 trim;
RPTFE/metal seat; class 300.
VE-463C
H3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
buttweld ends ASME B16.25; body ASTM A 182 Gr F 316L;
AISI 316L trim; PEEK seat; ISO 17292 standard; class
2500.
VE-463D
H3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation;
buttweld ends ASME B16.25; body ASTM A 182 Gr F 316L;
AISI 316L trim; PEEK seat; ISO 17292 standard; class
2500.
VE-464
C30
Ball valve; fire tested; full bore; carbon steel with Inconel
625; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; ends ASME B16.5; raised face (RF);
body ASTM A 105; AISI 410 trim; RPTFE/metal seat; class
300.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
61
of
90
TITLE:
Valves Description
TAG
VE-465
Spec
C30
Description
Ball valve; fire tested; full bore; carbon steel with Inconel
625; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; ends ASME B16.5; raised face (RF);
body ASTM A 216 Gr WCB; AISI 410 trim; RPTFE/Metal
seat; class 300.
VE-466
C30
Ball valve; fire tested; full bore; carbon steel with Inconel
625;
bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; ends ASME B16.5; raised face
(RF); body ASTM A 105; AISI 410 trim; RPTFE/Metal seat;
class 300.
VE-466C
H3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple Sch 160; body ASTM A 182 Gr F
316L; AISI 316L trim; PEEK seat; ISO 17292 standard;
class 2500.
VE-466D
H3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple XXS; body ASTM A 182 Gr F 316L;
AISI 316L trim; PEEK seat; ISO 17292 standard; class
2500.
VE-467
H30
Ball valve; fire tested; full bore; carbon steel with Inconel
625;
bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; compact flanged Norsok L-005;
metallic seal joint (MSJ); body ASTM A 105; AISI 410 trim;
PEEK/metal seat; class 2500.
VE-467P
H30P
Ball valve; piggable; fire tested; full bore; carbon steel with
Inconel 625; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; compact flanged Norsok
L-005; metallic seal joint (MSJ); body ASTM A 105; AISI 410
trim; PEEK/metal seat; class 2500. Note: Internal diameter
(ID) valve shall be defined for Project Engineer.
VE-468
H3
Ball valve; full bore; stainless steel; bolted body; trunnionmounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 182 Gr F316; AISI 316 trim; PEEK seat; ISO 14313 (API
6D) standard; class 2500.
VG-01
B7 B7R
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
62
of
90
TITLE:
Valves Description
TAG
VG-02
Spec
Description
B22 B23 B24 Gate valve; stainless steel; bolted bonnet; solid wedge;
OS&Y; non rising handwheel; screwed ends ASME B1.20.1
NPT; body ASTM A 182 Gr F316; trim (wedge-seat) AISI 304
Stellite; flexible graphite gasket with Inconel wire; 15761
(API 602) standard; class 800.
VG-03
B9 B10
VG-03B
B14
VG-04
B9 B10
VG-04A
B9 B10
VG-04B
B14 B23
VG-05
C9 C10
VG-05B
C14
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
63
of
90
TITLE:
Valves Description
TAG
VG-06
Spec
C9 C10
Description
Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
lateral wrench operator; flanged ends ASME B16.5; raised
face (RF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; flexible graphite gasket with Inconel wire; ISO 10434
(API 600) standard; class 300.
VG-06A
C14
VG-06B
C14
VG-07
C4
VG-07A
C4
VG-10
E9 E10 E10R Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
E14
non rising handwheel; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410; flexible graphite gasket with Inconel wire; ISO
10434 (API 600) standard; class 600.
VG-11
E9 E10 E10R Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
E14
lateral wrench operator; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410; flexible graphite gasket with Inconel wire; ISO
10434 (API 600) standard; class 600.
VG-12
F10 F10R
F14
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
64
of
90
TITLE:
Valves Description
TAG
VG-13
Spec
F10 F10R
F14
Description
Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
lateral wrench operator; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410; flexible graphite gasket with Inconel wire; ISO
10434 (API 600) standard; class 900.
VG-14
F10 F10R Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
F14 G10 non rising handwheel; flanged ends ASME B16.5; ring type
G10R G14 joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410; flexible graphite gasket with Inconel wire; ISO
10434 (API 600) standard; class 1500.
VG-15
G10 G10R
G14
VG-16
H10 H14
VG-17
H10 H14
VG-18
B3 B7 B7R
VG-19
B3 B7 B7R
VG-19A
B7 B7R
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
65
of
90
TITLE:
Valves Description
TAG
VG-20
Spec
C3
Description
Gate valve; stainless steel; bolted bonnet; solid wedge;
OS&Y; non rising handwheel; flanged ends ASME B16.5;
raised face (RF); body ASTM A 351 Gr CF8M; trim (wedgeseat) AISI 316; flexible graphite gasket with Inconel wire;
ISO 10434 (API 600) standard; class 300.
VG-21
C3
VG-24
E3
VG-25
E3
VG-26
F3
VG-27
F3
VG-28
F3 G3
VG-29
G3
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
66
of
90
TITLE:
Valves Description
TAG
VG-30
Spec
H3
Description
Gate valve; stainless steel; bolted bonnet; solid wedge;
OS&Y; non rising handwheel; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 351 Gr CF8M; trim
(wedge-seat) AISI 316; flexible graphite gasket with Inconel
wire; ISO 10434 (API 600) standard; class 2500.
VG-31
H3
VG-34
A4 A8
VG-35
A4
VG-36
A4 B7 B7R
Gate valve; FF; bolted bonnet, solid wed ge; OS&Y; lateral
wrench operator; flanged ends ASME B16.1; flat face (FF);
body ASTM A126 class CL B; trim (wedge-seat) ASTM B62
(UNS C83600); PTFE gasket; MSS SP-70 standard; class
125.
Gate valve; brass; union bonnet; solid wedge; OS&Y; rising
handwheel; screwed end; body ASTM B62 (UNS C83600);
trim (wedge-seat) ASTM B62 (UNS C83600); PTFE gasket;
MSS SP-80 standard; class 150.
VG-39
B4
VG-39A
B4
VG-45
B4 B9 B10
C4 C9 C10
E4 E9 E10
E10R
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
67
of
90
TITLE:
Valves Description
TAG
VG-46
Spec
F4 F10
F10R G4
G10 G10R
Description
Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
non rising handwheel; socket weld ends; body ASTM A 105
trim (wedge-seat) AISI 304 Stellite; flexible graphite gasket
with Inconel wire; ISO 15761 (API 602) standard; class
1500.
VG-50
B13 C13
VG-51
B12 C12
VG-52
B3 C3 E3
VG-53
F3 G3
VG-54
H3
VG-55
B12 B13
VG-56
B12 B13
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
68
of
90
TITLE:
Valves Description
TAG
VG-56A
Spec
B12
Description
Gate valve; stainless steel superduplex; bolted bonnet; solid
wedge; OS&Y; lateral wrench operator; flanged ends ASME
B16.47 Series A; raised face (RF); body-wedge-seat ASTM A
995 Gr 5A (UNS J93404); flexible graphite gasket with
Inconel wire; ISO 10434 (API 600) standard; class 150.
VG-57
C12 C13
VG-58
C12 C13
VG-59
B22 B23 B24 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; flat face
(FF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
316; flexible graphite gasket with Inconel wire; ISO 10434
(API 600) standard; class 150.
VG-60
B22 B23 B24 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
lateral wrench operator; flanged ends ASME B16.5; flat face
(FF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
316; flexible graphite gasket with Inconel wire; ISO 10434
(API 600) standard; class 150.
VG-60A
B22
VG-61
E4
VG-62
E4
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
69
of
90
TITLE:
Valves Description
TAG
VG-64
Spec
F4
Description
Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
lateral wrench operator; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410 Stellite; flexible graphite gasket with Inconel
wire; ISO 10434 (API 600) standard; class 900.
VG-65
F4 G4
VG-66
G4
VG-67
G12
VG-68
G12
VG-69
G12
VG-70
B11
VG-71
B11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
70
of
90
TITLE:
Valves Description
TAG
VG-72
Spec
B11
Description
Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
lateral wrench operator; flanged ends ASME B16.5; raised
face (RF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; body-wedge organic coated; flexible graphite gasket with
Inconel wire; ISO 10434 (API 600) standard; class 150.
VG-73
G11
VG-74
G11
VG-75
G11
VG-76
H11
VG-77
H11
VG-81
C11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
71
of
90
TITLE:
Valves Description
TAG
VG-82
Spec
C11
Description
Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
lateral wrench operator; flanged ends ASME B16.5; raised
face (RF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; body-wedge organic coated; flexible graphite gasket with
Inconel wire; ISO 10434 (API 600) standard; class 300.
VG-85
C11
VG-87
J12
VG-88
B16 C16
E16
VG-89
B16
VG-90
B16
VG-90A
B16
VG-92
C16
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
72
of
90
TITLE:
Valves Description
VG-93
TAG
Spec
C16
Description
Gate valve; duplex stainless steel; bolted bonnet; solid
wedge; OS&Y; lateral wrench operator; flanged ends ASME
B16.5; raised face (RF); body-wedge-seat ASTM A 995 Gr
4A (UNS J92205); flexible graphite gasket with Inconel wire;
ISO 10434 (API 600) standard; class 300.
VG-95
E16
VG-96
E16
VG-100
A8
VG-105
H3
VG ABRAS-04
B5 C5 E5
VG ABRAS-05
F5
VG ABRAS-06
G5
VG ABRAS-07
H5
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
73
of
90
TITLE:
Valves Description
TAG
Spec
VGL-01
B7 B7R
VGL-03
VGL-03A
VGL-03B
Description
Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; screw ends ASME
B1.20.1 NPT; body ASTM A 105; trim (disc-seat) AISI 304
Stellite; ISO 15761 (API 602) standard; class 800.
B22 B23 B24 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; flat face (FF); body ASTM A 216 Gr WCB; body-seat
AISI 316; BS 1873 standard; class 150.
VGL-04
C9 C10
VGL-04B
C14
VGL-05
C4
VGL-07
E9 E10 E10R Globe valve; carbon steel; bolted bonnet; chamfer disc;
E14
outside screw stem; rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 216 Gr WCB;
body-seat AISI 410; BS 1873 standard; class 600.
VGL-07E
E9 E10 E10R Globe valve; carbon steel; bolted bonnet; chamfer disc;
E14
outside screw stem; lateral wrench operator; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 216 Gr
WCB; body-seat AISI 410; BS 1873 standard; class 600.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
74
of
90
TITLE:
Valves Description
TAG
VGL-08
Spec
F10 F10R
F14
Description
Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 216 Gr WCB;
body-seat AISI 410; BS 1873 standard; class 900.
VGL-08E
F10 F10R
F14
VGL-09
F10 F10R
F14 G10
G10P G10R
G14
VGL-09E
G10 G10P Globe valve; carbon steel; bolted bonnet; chamfer disc;
G10R G14 outside screw stem; lateral wrench operator; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 216 Gr
WCB; body-seat AISI 410; BS 1873 standard; class 1500.
VGL-10
B3
VGL-11
C3
VGL-13
E3
VGL-13E
E3
VGL-14
F3
VGL-14E
F3
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
75
of
90
TITLE:
Valves Description
TAG
Spec
VGL-15
F3 G3
VGL-15E
G3
VGL-16
Description
A4 B7 B7R Globe valve; brass; union bonnet; chamfer disc; inside screw
stem; screw ends; ASME B1.20.1 NPT; body-disc-seat
ASTM B62; MSS SP-80 standard; class 150.
VGL-18
A4 A8
Globe valve; FF; bolted bonnet; cham fer disc; outside screw
stem; rising handwheel; flanged ends ASME B16.1; flat face
(FF); body ASTM A126 CL B; trim (disc-seat) ASTM B62;
CEN EN 13789 standard; class 125.
VGL-19
H10 H14
VGL-19E
H10 H14
VGL-20
B4
VGL-22
B6
VGL-23
C6
VGL-24
E6 E6R
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
76
of
90
TITLE:
Valves Description
TAG
VGL-24E
Spec
E6 E6R
Description
Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; lateral wrench operator; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 352 Gr
LCB; trim (disc-seat) AISI 304; BS 1873 standard; class 600.
VGL-28
F6 F6R G6
G6R G19
VGL-28E
G6 G6R
G19
VGL-29
F6 F6R
VGL-29E
F6 F6R
VGL-30
H3
VGL-30E
H3
VGL-31
A4 B7 B7R
Globe valve angular; for hydrant with adapter and cap; brass;
PETROBRAS N-111 standard; screwed bonnet; plain disc
with ring; inside screw stem; rising handwheel; inlet screw
female end ASME B1.20.1 NPT; outlet screw male end
NFPA 1693 2,5-7,5 NH; with adapter for hose standard
PETROBRAS N-1268 standard; with cap PETROBRAS N1272 standard and chain; body trim (disc-seat) ASTM B62;
angle 90 degrees; max. pressure 200 psi.
VGL-34
E4
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
77
of
90
TITLE:
Valves Description
TAG
Spec
Description
VGL-34E
E4
VGL-35
F4
VGL-35E
F4
VGL-36
F4 G4
VGL-36E
G4
VGL-37
B12 B13
VGL-38
C12 C13
VGL-39
B25
VGL-40
G12
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
78
of
90
TITLE:
Valves Description
TAG
VGL-41
Spec
B11
Description
Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; raised face (RF); body ASTM A 216 Gr WCB; trim
(disc-seat) AISI 410; body-trim organic coated; BS 1873
standard; class 150.
VGL-42
G11
VGL-42E
G11
VGL-43
H11
VGL-43E
H11
VGL-45
C11
VGL-47
B16
VGL-84
C16
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
79
of
90
TITLE:
Valves Description
TAG
VGL-85
Spec
E16
VGL-86
E16
VGL-87
G16
VGL-92
H30 H30P
VGL-94
J31
VGL-95
E30
VGL-96
C30
VR-01
C8 E8
VR-03
F4 F10
F10R G4
G10 G10R
VR-25
A4 B7 B7R
Globe valve;
disc; OS&Y;
ends ASME
ASTM A 995
600.
Description
duplex stainless steel; bolted bonnet; chamfer
outside screw stem; rising handwheel; flanged
B16.5; ring type joint (RTJ); body-disc-seat
Gr 4A (UNS J92205); BS 1873 standard; class
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
80
of
90
TITLE:
Valves Description
TAG
Spec
Description
standard; class 200.
VR-28
B9 B10
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 410; metal-metal; API 594
standard; class 150.
VR-28A
B9 B10
Check valve; wafer; dual plate type; carbon steel; raised face
(RF) ASME B16.47 Series A; finishing as MSS SP-6; bodydisc ASTM A 216 Gr WCB; spring Inconel; stem AISI 410;
metal-metal; API 594 standard; class 150.
VR-29
C9 C10
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 410; metal-metal; API 594
standard; class 300.
VR-35
B5 B9 B10
B15
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 316; Viton seat TBR-S; API
594 standard; class 150.
VR-35A
B9 B10 B15 Check valve; wafer; dual plate type; carbon steel; raised
face (RF) ASME B16.47 Series A; finishing as MSS SP-6;
body-disc ASTM A 216 Gr WCB; spring Inconel; stem AISI
316; Viton seat TBR-S; API 594 standard; class 150.
VR-36
C5 C9 C10
VR-38
E5 E9 E10
E10R
VR-39
F5 F10
F10R
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216
Gr WCB; spring Inconel; stem AISI 316; Viton seat TBR-S;
API 594 standard; class 600.
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216
Gr WCB; spring Inconel; stem AISI 316; Viton seat TBR-S;
API 594 standard; class 900.
VR-40
F5 F10
F10R G5
G10 G10R
VR-41
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216
Gr WCB; spring Inconel; stem AISI 316; Viton seat TBR-S;
API 594 standard; class 1500.
H5 H10 H14 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
81
of
90
TITLE:
Valves Description
TAG
Spec
Description
Gr WCB; spring Inconel; stem AISI 316; Viton seat; API
594 standard; class 2500.
VR-42
B3 B7 B7R
VR-42A
B7 B7R
VR-43
C3
VR-45
E3
Check valve; wafer; dual plate type; stainless steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc-stem ASTM A
351 Gr CF8M; spring Inconel; Viton seat TBR-S; API 594
standard; class 600.
VR-46
F3
Check valve; wafer; dual plate type; stainless steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc-stem ASTM A
351 Gr CF8M; spring Inconel; Viton seat TBR-S; API 594
standard; class 900.
VR-47
F3 G3
Check valve; wafer; dual plate type; stainless steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc-stem ASTM A
351 Gr CF8M; spring Inconel; Viton seat TBR-S; API 594
standard; class 1500.
VR-48
H3
Check valve; wafer; dual plate type; stainless steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc-stem ASTM A
351 Gr CF8M; spring Inconel; Viton seat TBR-S; API 594
standard; class 2500.
VR-49
A4 A8
Check valve; wafer; dual plate type; FF; flat face (FF);
finishing as MSS SP-6; body ASTM A 126 class B; disc
brass ASTM B584; spring stem AISI 316; Viton seat; API 594
standard; class 125.
VR-50
H10
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
82
of
90
TITLE:
Valves Description
TAG
Spec
Description
VR-52
B6 C6 E6
E6R
VR-53
B6
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 352 Gr LCB;
spring Inconel; stem AISI 304; Viton seat TBR-S; API 594
standard; class 150.
VR-53A
B6
Check valve; wafer; dual plate type; carbon steel; raised face
(RF) ASME B16.47 Series A; finishing as MSS SP-6; bodydisc ASTM A 352 Gr LCB; spring Inconel; disc AISI 304;
Viton seat TBR-S; API 594 standard; class 150.
VR-54
C6
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 352 Gr LCB;
spring Inconel; stem AISI 304; Viton seat TBR-S; API 594
standard; class 300.
VR-55
E6 E6R
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 352 Gr
LCB; spring Inconel; stem AISI 304; Viton seat; API 594
standard; class 600.
VR-56
B4 B9 B10
B15 C4 C9
C10 E4 E9
E10 E10R
VR-58
F6 F6R G6
G6R G19
VR-59
F6 F6R G6
G6R G19
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 352 Gr
LCB; spring Inconel; stem AISI 304; Viton seat; API 594
standard; class 1500.
VR-60
F6 F6R
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 352 Gr
LCB; spring Inconel; stem AISI 304; Viton seat; API 594
standard; class 900.
VR-64
B14 B22
B23 B24
Check valve; wafer; dual plate type; carbon steel; flat face
(FF); body-disc ASTM A 216 Gr WCB; spring stem AISI 410;
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
83
of
90
TITLE:
Valves Description
TAG
Spec
Description
Viton seat; API 594 standard; class 150.
VR-64A
B14 B22
Check valve; wafer; dual plate type; carbon steel; flat face
(FF) ASME B16.47 Series A; finishing as MSS SP-6; bodydisc ASTM A 216 Gr WCB; spring stem AISI 410; Viton seat;
API 594 standard; class 150.
VR-65
C14
Check valve; wafer; dual plate type; carbon steel; flat face
(FF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring stem AISI 316; Viton seat; API 594 standard;
class 300.
VR-65A
C14
Check valve; wafer; dual plate type; carbon steel; flat face
(FF) ASME B16.47 Series A; finishing as MSS SP-6; bodydisc ASTM A 216 Gr WCB; spring stem AISI 316; Viton seat;
API 594 standard; class 300.
VR-66
E14
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring stem AISI 316; Viton seat; API 594 standard;
class 600.
VR-67
F14
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring stem AISI 316; Viton seat; API 594 standard;
class 900.
VR-68
F14 G14
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring stem AISI 316; Viton seat; API 594 standard;
class 1500.
VR-71
B6
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body ASTM A 352 Gr LCB;
spring Inconel; disc AISI 410-Stellite; metal-metal; API
594 standard; class 150.
VR-71A
B6
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); ASME B16.47 Series A; finishing as MSS SP-6; bodydisc ASTM A 352 Gr LCB; spring Inconel; disc AISI 304;
metal-metal; API 594 standard; class 150.
VR-72
B12 B13
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
84
of
90
TITLE:
Valves Description
TAG
Spec
Description
VR-72A
B12
VR-73
C12 C13
Check
valve;
wafer;
dual
plate
type;
stainless
steelsuperduplex; raised face (RF); finishing as MSS SP-6;
body-disc-stem ASTM A 995 Gr 5A (UNS J93404); Viton seat
TBR-S; API 594 standard; class 300.
VR-74
B3
VR-75
B22 B23
B24
VR-76
B4
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 410-Stellite; Viton seat
TBR-S; API 594 standard; class 150.
VR-77
B4
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 410-Stellite; metal-metal;
API 594 standard; class 150.
VR-78
B6
VR-79
C6
VR-80
E6 E6R
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
85
of
90
TITLE:
Valves Description
TAG
Spec
Description
VR-81
F6 F6R
VR-82
F6 F6R G6
G6R G19
VR-83
B3 C3 E3
VR-84
F3 G3
VR-85
H3
VR-86
B13 C13
VR-87
C12
VR-88
B21
VR-89
B20
Check valve; ball type; socket weld ends; body-ball PVC; flat
face (FF); class 150 psig.
VR-90
B25
Check valve; wafer; dual plate type; stainless steel; flat face
(FF); finishing as MSS SP-6; body ASTM A 351 Gr CD4MCU;
disc-spring AISI 316L; Hypalon seat; API 594 standard; class
150.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
86
of
90
TITLE:
Valves Description
TAG
VR-91
Spec
B25
Description
Check valve; horizontal; globe type; stainless steel; bolted
bonnet; chamfer piston disc; flanged ends ASME B16.5; flat
face (FF); body ASTM A 351 Gr CD4MCU; disc-spring AISI
316L; Hypalon seat; BS 1868 standard; class 150.
VR-92
B14
VR-93
C14
VR-94
E14
VR-95
F14 G14
VR-96
C4
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 410-Stellite; Viton seat
TBR-S; API 594 standard; class 300.
VR-97
C4
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 410-Stellite; metal-metal;
API 594 standard; class 300.
VR-98
E4 E8
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 410-Stellite; Viton seat
TBR-S; API 594 standard; class 600.
VR-99
E4
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 410-Stellite; metal-metal;
API 594 standard; class 600.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
87
of
90
TITLE:
Valves Description
TAG
Spec
Description
VR-100
F4 G4
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 410-Stellite; Viton seat
TBR-S; API 594 standard; class 1500.
VR-101
F4
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 410-Stellite; metal-metal;
API 594 standard; class 900.
VR-102
G4
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 410-Stellite; metal-metal;
API 594 standard; class 1500.
VR-103
F4
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 410-Stellite; Viton seat
TBR-S; API 594 standard; class 900.
VR-104
G12
VR-105
G12
VR-107
B11
VR-108
B11
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 316; body-trim organic
coated; API 594 standard; class 150.
VR-108A
B11
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); ASME B16.47 Series A; finishing as MSS SP-6; bodydisc ASTM A 216 Gr WCB; spring Inconel; stem AISI 316;
body-trim organic coated; API 594 standard; class 150.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
88
of
90
TITLE:
Valves Description
TAG
Spec
Description
VR-109
G11
VR-110
G11
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 316; body-trim organic
coated; API 594 standard; class 1500.
VR-111
H11
VR-112
H11
Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel; stem AISI 316; body-trim with organic
coated; API 594 standard; class 2500.
VR-115
C11
Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr WCB;
spring Inconel; stem AISI 316; body-trim organic coated; API
594 standard; class 300.
VR-117
C11
VR-119
B16 C16
E16
VR-120
B16
VR-120A
B16
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
89
of
90
TITLE:
Valves Description
TAG
VR-122
Spec
C16
Description
Check valve; wafer; dual plate type; duplex stainless steel;
raised face (RF); finishing as MSS SP-6; body-disc-stem
ASTM A 995 Gr 4A (UNS J92205); Viton seat TBR-S; spring
Inconel; API 594 standard; class 300.
VR-124
E16
VR-126
G16
VR-127
A8
VR-132
H30
VR-133
H30
VR-136
H14
VR-137
E30
VR-138
E30
VR-139
C30
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
90
of
90
TITLE:
Valves Description
TAG
Spec
Description
VR-140
C30
Check valve; wafer; dual plate type; Inconel 625 alloy steel;
raised face (RF); finishing as MSS SP-6; body-disc-seat
Inconel 625; Viton seat TBR-S; spring Inconel; API 594
standard; class 300.
VR-141
H30
N:
TECHNICAL SPECIFICATION
CLIENT:
E&P
PROGRAM:
of
63
ET-200.03
TITLE:
TAG
SHEET:
AREA:
E&P - ENGP
DR-ENGP-1.1
Description
ADAPTF-01
B20
ADAPTF-02
B21
BRE-01
A4
BRE-05
B20
Bushing; pipe line; hex head; PVC poly vinyl chloride; ASTM
D 1784 class 12454; dimensions ASTM D 2464; socket
weld ends.
BRE-06
B21
BRE-91
B7 B7R
BUJ-01
A4
Plug; pipe line; hex head; carbon steel; ASTM A 105; ASME
B16.11 standard; class 3000; threaded ends ASME
B1.20.1.NPT.
B22 B23 B24 Plug; pipe line; hex head; stainless steel; ASTM A 182 Gr
F321; ASME B16.11 standard; class 3000; threaded ends
ASME B1.20.1 NPT.
BUJ-06
BUJ-91
B7 B7R
C453D-01
C30 G10P
E30
Date
Project
Execution
Verification
Approval
Original
REV. E
REV. F
REV. G
REV. H
REV. J
REV. K
REV. L
REV. 2
Dez/78
DEPRO
M. Assayag
Hernon
Hernon
Jan/98
E&P
Fernando
Hernon
Hernon
Nov/05
E&P
Fernando
Hernon
Joper
Dez/05
E&P
Fernando
Hernon
Joper
Jan/06
E&P
Fernando
Hernon
Joper
Mar/06
E&P
Fernando
Hernon
Joper
May/06
E&P
Fernando
Hernon
Joper
Feb/07
E&P
Fernando
Hernon
Joper
Sep/10
E&P
EISA
IPP
ENGP
THE INFORMATION OF THIS DOCUMENT ATE PROPERTY OF PETROBRAS, BEING FORBIDDEN THE USE OF ITS PURPOSE.
STANDARDIZED FORM BY PETROBRAS NORM N-381 REV. F
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
63
TITLE:
Spec
Description
C453D-02
G10P
C453D-03
G12P
C453D-06
H30 H30P
C455D-01
G10P
C455D-02
G10P
C455D-03
G12P
C455D-03
H30P
C903D-01
C30 G10P
E30
C903D-02
G10P
C903D-03
G12P
C903D-06
H30P
C905D-01
G10P
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
63
TITLE:
Spec
Description
C905D-02
G10P
C905D-03
G12P
C905D-06
H30 H30P
CONF-91
B7 B7R
CONM-91
B7 B7R
CRC-01
CRC-02
CRC-04
CRC-05
B13 C13
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
63
TITLE:
Spec
Description
B12 C12 G12 Elbow; pipe line; stainless steel superduplex; ASTM A 815
J12
(UNS S32760); ASME B16.9 standard; 90 degrees; short
radius; buttwelding ends ASME B16.25.
CRC-07
B15
CRC-08
B25
CRC-09
B25
CRC-10
B25
CRC-11
B25
CRC-12
B25
CRC-13
B25
CRC-14
B25
CRC-15
B25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
63
TITLE:
Spec
Description
CRC-16
B25
CRC-17
B25
CRC-18
B25
CRC-19
B25
CRC-20
G10 G11
G14 H10
CRC-21
H11 H14
CRC-22
B16
CRC-23
J31
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
63
TITLE:
Spec
Description
CRL-01
CRL-02
CRL-03
CRL-04
CRL-07
CRL-08
CRL-09
G10 G11
G14 H10
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
63
TITLE:
Spec
Description
CRL-10
G10 G11
G14 H10
CRL-11
B13 C13
CRL-12
B13 C13
CRL-13
B12 C12 G12 Elbow; pipe line; stainless steel superduplex; ASTM A 815
J12
(UNS S32760); ASME B16.9 standard; 90 degrees; long
radius; buttwelding ends ASME B16.25.
CRL-14
B12 C12 G12 Elbow; pipe line; stainless steel superduplex; ASTM A 815
J12
(UNS S32760); ASME B16.9 standard; 45 degrees; long
radius; buttwelding ends ASME B16.25.
CRL-15
B22 B23
CRL-16
B24
CRL-17
B22 B23
CRL-18
B24
CRL-19
B15
CRL-20
H11 H14
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
63
TITLE:
Spec
Description
CRL-21
H11 H14
CRL-30
B16
CRL-31
B16
CRL-32
J31
CRL-33
J31
CRL-92
B7 B7R
CRL-93
B7 B7R
CRL-94
B7R
CRL-95
B7R
CRUZ-01
A4
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
of
63
TITLE:
Spec
Description
CRUZ-02
CRUZ-05
CRUZ-06
B9 B10 B11 Cross; pipe line; carbon steel; ASTM A 105; ASME B16.11
B15 C9 C10 standard; class 6000; socket weld ends.
E9 E10 F4
F10 F10R
F14 G4 G10
G10R G10P
G11 G14
CRUZ-08
CRUZ-09
B6 C6 E6
E6R
CRUZ-12
CRUZ-15
CRUZ-16
G3 H3
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
10
of
63
TITLE:
Spec
CRUZ-17
B13 C13
CRUZ-18
B12 C12
CRUZ-19
CRUZ-20
CRUZ-21
Description
B12 C12 G12 Cross; pipe line; stainless steel superduplex; ASTM A 815
J12
(UNS S32760); ASME B16.9 standard; buttwelding ends
ASME B16.25.
CRUZ-22
B25
CRUZ-23
B25
CRUZ-24
B25
CRUZ-25
G10 G11
G14 H10
CRUZ-26
G12
CRUZ-27
H11 H14
CRUZ-28
H10 H11
H30P
CRUZ-29
J12
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
11
of
63
TITLE:
Spec
B16
Description
Croos; pipe line; duplex stainless steel; ASTM A 182 Grade
F 51 (UNS S31803); ASME B16.11 standard; class 3000;
socket weld ends.
CRUZ-33
B16
CRUZ-34
C30 H30 E30 Croos; pipe line; carbon steel; ASTM A 105; ASME B16.9
standard; buttwelding ends ASME B16.25.
CRUZ-35
J31
Croos; pipe line; Alloy steel; ASTM A 420 Gr. WPL8; ASME
B16.11 standard; buttwelding ends ASME B16.25
CRUZ-37
J31
Croos; pipe line; Alloy steel; ASTM A 420 Gr. WPL8; ASME
B16.11 standard; buttwelding ends ASME B16.25
CRUZ-39
H30
CRUZR-01
B25
CRUZR-02
B25
CRUZR-03
B25
FLG-01B
A4
FLG-02A
A4 B14
FLG-02B
B14
FLG-03A
B15
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
12
of
63
TITLE:
Spec
FLG-03B
B15
FLG-04A
Description
Flange; pipe line; slip-on; carbon steel; ASTM A 105; ASME
B16.47 Series A standard; raised face (RF); serrated
finishing 125 in 250 in; class 150.
FLG-04B
A4 A8 B5
B14
FLG-04C
B9 B10
FLG-04D
B14
FLG-05A
FLG-05B
FLG-05C
B9 B10 B15 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
B16.47 Series A standard; raised face (RF); serrated
finishing 125 in 250 in; class 150.
FLG-05D
B14
FLG-05E
A8 B4 B9
B10 B11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
13
of
63
TITLE:
Spec
FLG-05F
A8 B14
FLG-09C
C14
FLG-09D
C14
FLG-10A
Description
FLG-10B
C14
FLG-10C
C9
FLG-10D
C14
FLG-11A
C4 C8 C9
C10 C11
FLG-11B
C14
FLG-11C
C9
FLG-11D
C14
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
14
of
63
TITLE:
Spec
Description
FLG-13
FLG-15
FLG-16
F4 F5 F10
F10R F14
FLG-17
F4 F5 F10
F10R F14
FLG-18
F4 F5 F10 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
F10R F14 G4 ASME B16.5 standard; ring type joint (RTJ); surface finish
G5 G10
not exceed 63 in; class 1500.
G10R G10P
G11 G14
FLG-19
F4 F5 F10 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
F10R F14 G4 B16.5 standard; ring type joint (RTJ); surface finish not
G5 G10
exceed 63 in; class 1500.
G10R G10P
G11 G14
FLG-20
H5 H10 H11 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
H30 H30P ASME B16.5 standard; ring type joint (RTJ); surface finish
not exceed 63 in; class 2500.
FLG-21
H5 H10 H11 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
H30 H30P B16.5 standard; ring type joint (RTJ); surface finish not
exceed 63 in; class 2500.
FLG-22A
B6
FLG-22B
B6
FLG-23A
B6
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
15
of
63
TITLE:
Spec
Description
FLG-23B
B6
FLG-24
C6
FLG-25
C6
FLG-26
E6 E6R
FLG-27
E6 E6R
FLG-32
F6 F6R
FLG-33
F6 F6R
FLG-34
F6 F6R G6 Flange; pipe line; welding neck; carbon steel; ASTM A 350
G6R
Gr LF2 CL1; ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 in; class 1500.
FLG-35
F6 F6R G6 Flange; pipe line; blind; carbon steel; ASTM A 350 Gr LF2
G6R
CL1; ASME B16.5 standard; ring type joint (RTJ); surface
finish not exceed 63 in; class 1500.
FLG-41A
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
16
of
63
TITLE:
Spec
FLG-41B
C14
FLG-42
Description
Flange; pipe line; socket welding; carbon steel; ASTM A
105; ASME B16.5 standard; full face (FF); serrated finishing
125 in 250 in; class 300;
C14 For pipe NPS 1" - 1 Sch 80.
FLG-43
F4 F10 F10R
F14 G4 G10
G10R G10P
G11 G14
FLG-44
H10
FLG-45
B6
FLG-46
C6
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
17
of
63
TITLE:
Spec
FLG-47
E6 E6R
FLG-48
Description
Flange; pipe line; socket welding; carbon steel; ASTM A 350
Gr LF2 CL1; ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 in; class 600;
E6 For pipe NPS - Sch 160.
E6R For pipe NPS 1 - 1 Sch 80.
F6 F6R G6 Flange; pipe line; socket welding; carbon steel; ASTM A 350
G6R
Gr LF2 CL1; ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 in; class 1500;
F6 For pipe NPS - Sch 160.
F6 For pipe NPS 1 - 1 Sch 80.
F6R For pipe NPS - Sch 160.
F6R For pipe NPS 1 - 1 Sch 80.
G6 For pipe NPS - 1 XXS.
G6R For pipe NPS - 1 XXS.
FLG-49A
B3
FLG-49B
B3
FLG-50A
B3
FLG-50B
B3
FLG-51
B3
FLG-52
C3
FLG-53
C3
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
18
of
63
TITLE:
Spec
Description
FLG-54
C3
FLG-55
E3
FLG-56
E3
FLG-57
E3
FLG-58
F3
FLG-59
F3
FLG-60
F3 G3
FLG-61
F3 G3
FLG-62
F3 G3
FLG-63
H3
FLG-64
H3
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
19
of
63
TITLE:
Spec
Description
FLG-65
H3
FLG-66
B13
FLG-67
B13
FLG-68
B13
FLG-69
B12
FLG-69A
C12
FLG-70
B12
FLG-70A
C12
FLG-71
B12
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
20
of
63
TITLE:
Spec
Description
FLG-72
G10 G10P
G11 G14
FLG-73
G10 G10P
G11 G14
FLG-74
B20
FLG-75
B20
FLG-76
B21
FLG-77
B21
FLG-78
B25
FLG-79
B25
FLG-80
B25
FLG-81
B25
FLG-82
B25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
21
of
63
TITLE:
Spec
Description
FLG-83
B22 B23
Flange; pipe line; welding neck; FRP; ASTM D 4024-00RTR; (Thermosetting resin reinforced fiber); full face (FF);
class 150.
a1 (filament wound).
bResin according manufacturer approval Classification
Society, with external layer of improved resin with ultraviolet
inhibitor.
cFabrication
accordant
manufacturer
approval
Classification Society.
FLG-85
B22 B23
FLG-86
B24
Flange; pipe line; welding neck; FRP; ASTM D 4024-00RTR (Thermosetting resin reinforced fiber); full face (FF);
class 150.
a1 (filament wound).
bPhenolic resin, with external layer of improved resin with
ultraviolet inhibitor.
cFabrication
accordant
manufacturer
approval
Classification Society.
FLG-88
B24
FLG-89
H10
FLG-90
B7 B7R
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
22
of
63
TITLE:
Spec
Description
FLG-92
B7 B7R
FLG-92A
B7
FLG-93
B7 B7R
FLG-93A
B7
FLG-94
B7R
FLG-94A
B7R
FLG-95
B7R
FLG-95A
B7R
FLG-100
C13
FLG-101
C13
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
23
of
63
TITLE:
Spec
Description
FLG-102
C13
FLG-103
C12
FLG-104
C12
FLG-105
C12
FLG-106
H10
FLG-109
G12 G12P
FLG-110
G12 G12P
FLG-111
G12 G12P
FLG-112
H11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
24
of
63
TITLE:
Spec
Description
FLG-113
H11
FLG-114
J12
FLG-115
J12
FLG-116
J12
FLG-118
H14
FLG-119
H14
FLG-120
B16
FLG-121
B16
FLG-121A
B16
FLG-122
B16
FLG-122A
B16
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
25
of
63
TITLE:
Spec
Description
FLG-133
H14
FLG-134
H14
FLG-141
H30 H30P
FLG-142
H30 H30P
FLG-149
J31 J31P
FLG-150
J31 J31P
Flange; pipe line; welding neck; alloy steel; ASTM A 522 type
I; NORSOK L-005 standard; metallic seal joint (MSJ); surface
finish see ISO 4287; API 10000.
FLG-151
E30
FLG-152
E30
FLG-153
H30 H30P
FLG-154
H30 H30P
FLG-155
H14
FLG-156
H14
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
26
of
63
TITLE:
Spec
Description
JO-01
A4
JO-02
A4
JO-07
JO-08
JO-09
B9 B10 B11 Elbow; pipe line; carbon steel; ASTM A 105; ASME B16.11
B15 C9 C10 standard; 90 degrees; class 6000; socket weld ends.
E9 E10 F4
F10 F10R
F14 G4 G10
G10R G10P
G11 G14
JO-10
B9 B10 B11 Elbow; pipe line; carbon steel; ASTM A 105; ASME B16.11
B15 C9 C10 standard; 45 degrees; class 6000; socket weld ends.
E9 E10 F4
F10 F10R
F14 G4 G10
G10R G10P
G11 G14
JO-13
B6 C6 E6
E6R
JO-14
B6 C6 E6
E6R
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
27
of
63
TITLE:
Spec
Description
JO-17
JO-18
JO-23
JO-24
JO-25
G3 H3
JO-26
G3 H3
JO-27
B13 C13
JO-28
B13 C13
JO-29
B12 C12
JO-30
B12 C12
JO-31
B20
JO-32
B20
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
28
of
63
TITLE:
Spec
JO-33
B21
JO-34
B21
JO-35
G12
JO-36
G12
JO-39
J12
JO-40
J12
JO-45
B16
JO-46
B16
JO-92
B7 B7R
JO-93
B7 B7R
JA-01
Description
B5 C5 E4 E5 Ring type joint, flange; oval type R; carbon steel coated ZnE8 E9 E10 Ni; max. hardness 90 HB; for flange class 600/900; ASME
E10R E14 F4 B16.20 standard.
F5 F10 F10R
F14
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
29
of
63
TITLE:
Spec
Description
JA-02
F4 F5 F10 Ring type joint, flange; octagonal type; carbon steel coated
F10R F14 G4 Zn-Ni; max. hardness 90 HB; for flange class 1500/2500;
ASME B16.20 standard.
G5 G10
G10R G10P
G11 G14 H5
H10 H11 H14
JA-03
E6 E6R F6 Ring type joint, flange; oval type R; stainless steel AISI 304;
F6R
max. hardness 150 HB; for flange class 600/900; ASME
B16.20 standard.
JA-04
F6 F6R G6 Ring type joint, flange; octagonal type; stainless steel AISI
G6R
304; max. hardness 150 HB; p/flange class 1500; ASME
B16.20 standard.
JA-05
E3 F3
JA-06
F3 G3 H3
JA-07
G12
Ring type joint, flange; octagonal type; for flange class 1500;
stainless steel AISI 316; max. hardness 150 HB; ASME
B16.20 standard.
JA-08
J12
Ring type joint, flange; octagonal type; for flange class API
10000; stainless steel superduplex; ASTM A 182 Gr F 55
(UNS S32760); ASME B16.20 standard.
JA12
E30
JA-13
H30 H30P
JE-04
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
30
of
63
TITLE:
Spec
Description
JE-05
JE-06
JE-07
JE-08
JE-09
JE-10
JI-01
C9
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
31
of
63
TITLE:
Spec
JI-02
A4 A8
Description
Circular isolating gasket, for cathodic protection; flange; full
face type; flat face (FF); ASME B16.21 standard; phenolic
resin coated with neoprene; class 150; wall thickness 1/8
(3,2 mm); polyethylene isolating bushing; phenolic resin
isolating washer and washer carbon steel coated Zn-Ni; for
flange class 150.
JI-03
C9 C10 C12 Circular isolating gasket, for cathodic protection; flange flat
C13
ring, raised face (RF); ASME B16.21 standard; phenolic
resin coated with neoprene; class 300; wall thickness 1/8
(3,2 mm); polyethylene isolating bushing; phenolic resin
isolating washer and washer carbon steel coated Zn-Ni; for
flange class 300.
JI-04
E6 E6R E9
E10 E10R
E30 F10
F10R
JI-05
F10 F10R
G10 G10R
G10P G11
G12
H10 H11
H14 J12
JP-01
B22 B23 B24 Circular gasket; full face type for flange flat face (FF); PTFE
C11
expand; class 150; wall thickness 1/8 (3,2 mm); ASME
B16.21 standard.
JP-02
B25 C11
Circular gasket; full face type for flange full face (FF); armed
rubber; class 150; wall thickness 1/8 (3,2 mm); ASME
B16.21 standard.
JP-03
C11
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
32
of
63
TITLE:
Spec
Description
JPH-07
A8 B5 B7 Circular gasket; flat ring type; plain; for flange raised face
B7R B9 B10 (RF); compressed sheet non asbestos; ASME B16.21
B11 B12 B13 standard; class 150; wall thickness 1/16 (1,6 mm).
B15 B16
JPH-08
A8 B7 B7R Circular gasket; flat ring type; plain; for flange raised face
B9 B10 B11 (RF); compressed sheet non asbestos; ASME B16.21
B12 B13 B15 standard; class 150; wall thickness 1/8 (3,2 mm).
B16
JPH-09
A4 A8 B14 Circular gasket; full face type; plain; for flange full face (FF);
compressed sheet non asbestos; ASME B16.21 standard;
class 150; wall thickness 1/16 (1,6 mm).
JPH-10
A4 A8 B14 Circular gasket; full face type; plain; for flange full face (FF);
compressed sheet non asbestos; ASME B16.21 standard;
class 150; wall thickness 1/8 in (3,2 mm).
JPH-11
C5 C8 C9 Circular gasket; flat ring type; plain; for flange raised face
C10 C12 C13 (RF); compressed sheet non asbestos; ASME B16.21
standard; class 300; wall thickness 1/16 in (1,6 mm).
JPH-12
C9 C10 C12 Circular gasket; flat ring type; plain; for flange raised face
C13
(RF); compressed sheet non asbestos; ASME B16.21
standard; class 300; wall thickness 1/8 in (3,2 mm).
JPH-13
C14
Circular gasket; full face type; plain; for flange full face (FF);
compressed sheet non asbestos; ASME B16.21 standard;
class 300; wall thickness 1/16 in (1,6 mm).
JPH-14
C14
Circular gasket; full face type; plain; for flange full face (FF);
compressed sheet non asbestos; ASME B16.21 standard;
class 300; wall thickness 1/8 in (3,2 mm).
JPH-15
B20 B21
Circular gasket; full face type; plain; for flange full face (FF);
Teflon enveloped with non-asbestos insert; ASME B16.21
standard; class 150; wall thickness 1/8 in (3,2 mm).
JVM-01
H30 H30P
JVM-02
H14
JVM-03
J31 J31P
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
33
of
63
TITLE:
Spec
B25
Description
Coupling; pipe line; RPVC-PVC coated external with fiber
glass, thermosetting resin; flexible joint ends / bell-spigot
JE/PB.
L-04
L-05
B9 B10 B11 Coupling; pipe line; carbon steel; ASTM A 105; ASME
B15 C9 C10 B16.11 standard; class 6000; socket weld ends.
E9 E10 F4
F10 F10R
F14 G4 G10
G10R G10P
G11 G14
L-06
A4
L-08
B6 C6 E6
E6R
L-09
L-13
L-14
G3 H3
L-15
B13 C13
L-16
B12 C12
L-17
B20
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
34
of
63
TITLE:
Spec
L-18
B21
L-19
B22 B23
L-20
B24
L-21
B15
L-22
G12
L-24
J12
L-27
B16
L-28
C30 E30
L-91
B7 B7R
LRE-01
Description
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
35
of
63
TITLE:
LRE-03
Spec
Description
B9 B10 B11 Reducing coupling; pipe line; carbon steel; ASTM A 105;
B15 C9 C10 ASME B16.11 standard; class 6000; socket weld ends.
E9 E10 F4
F10 F10R
F14 G4 G10
G10R G10P
G11 G14
B6 C6 E6
E6R
LRE-04
LRE-05
LRE-06
G3 H3
LRE-07
B13 C13
LRE-08
B12 C12
LRE-09
B20
LRE-10
B21
LRE-16
B16
LRE-11
G12
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
36
of
63
TITLE:
Spec
Description
LRE-12
H30P
LRE-13
J12
LRE-17
C30 E30
LREFF-91
B7 B7R
LREMF-91
B7 B7R
ML-01
A4
ML-02
ML-03
B9 B10 B11 Half coupling; pipe line; carbon steel; ASTM A 105; ASME
B15 C5 C9 B16.11 standard; class 6000; socket weld ends.
C10 E5 E9
E10 F4 F5
F10 F10R
F14 G4 G5
G10 G10R
G10P G11
G14
ML-05
ML-07
B6 C6 E6
E6R
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
37
of
63
TITLE:
Spec
Description
ML-10
G3 H3
ML-11
B13 C13
ML-12
B12 C12
ML-13
G12
ML-14
H30P
ML-16
J12
ML-18
B16
ML-19
C30 E30
NIPC-07
B25
NIPADF-91
B7 B7R
NIPADM-91
B7 B7R
NIPM-91
B7 B7R
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
38
of
63
TITLE:
Spec
NIPRC-01
A4
Description
Concentric reducing nipple; pipe line; carbon steel; ASTM A
234 Gr WPB; seamless; thread ends ASME B1.20.1 NPT.
NIPRC-04
NIPRC-04A
NIPRC-04B
A4
NIPRC-05
NIPRC-05A
NIPRC-07
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
39
of
63
TITLE:
Spec
Description
NIPRC-08
B13 C13
NIPRC-08A
B13 C13
NIPRC-09
B12 C12 G12 Concentric reducing nipple; pipe line; stainless steel
J12
superduplex; ASTM A 815 (UNS S32760); seamless; plain
ends.
NIPRC-09A B12 C12 G12 Concentric reducing nipple; pipe line; stainless steel
J12
superduplex; ASTM A 815 (UNS S32760); seamless;
buttwelding end ASME B16.25 x plain end.
NIPRC-10
H14
NIPRC-11
B16
NIPRC-11A
B16
NIPRC-13
J31
NIPRE-07
A4
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
40
of
63
TITLE:
Spec
Description
NIPRE-10
NIPRE-10A
NIPRE-10B
A4
NIPRE-13
NIPRE-13A
NIPRE-14
B13 C13
NIPRE-14A
B13 C13
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
41
of
63
TITLE:
Spec
Description
B12 C12 G12 Eccentric reducing nipple; pipe line; stainless steel
J12
superduplex; ASTM A 815 (UNS S32760); seamless; plain
ends.
NIPRE-15A B12 C12 G12 Eccentric reducing nipple; pipe line; stainless steel
J12
superduplex; ASTM A 815 (UNS S32760); seamless;
buttwelding end ASME B16.25 x plain end.
NIPRE-16
NIPRE-16A
NIPRE-17
H14
NIPRE-18
B16
NIPRE-18A
B16
NIPRE-20
J31
PAE-01
(1/2 - 1)
A4 A8 B4 B5
B7 B7R B9
B10 B14 B15
B20 B21 B22
B23 B24 B25
C4 C5 C8 C9
C10 C14 E4
E5 E8 E9
E10 E10R
E14 F4 F5
F10 F10R
F14 G4 G5
G10 G10R
G10P G14
H5 H10 H11
Stud bolt; with two hexagonal nuts; bolt alloy steel ASTM A
193 Gr B7, Zn-Ni (Appendix 10); heavy nuts carbon steel
ASTM A 194 Gr 2H; Zn-Ni (Appendix 10); bolt size ASME
B18.2.1 and nuts ASME B18.2.2 standard; integral thread
UNC-2A stud and screw nuts ASME B1.1 standard.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
42
of
63
TITLE:
Spec
PAE-02
(1 1/8 - 2)
A4 B4 B7
B7R B9 B10
B14 B15 B22
B25 C4 C9
C10 C14 E4
E8 E9 E10
E10R E14 F4
F5 F10 F10R
F14 G4 G5
G10 10R
G10P G14
H5 H10 H11
Description
Stud bolt; with two hexagonal nuts; bolt alloy steel ASTM A
193 Gr B7, Zn-Ni (Appendix 10); heavy nuts carbon steel
ASTM A 194 Gr 2H; Zn-Ni (Appendix 10); bolt size ASME
B18.2.1 and nuts ASME B18.2.2 standard; integral thread
UN-2A stud and screw nuts ASME B1.1 standard.
PAE-03
(1/2 - 1)
B12 B13 B16 Stud bolt; with two hexagonal nuts; bolt stainless steel
C3 C12 C13 ASTM A 193 Gr B8M CL 2; heavy nuts carbon steel ASTM
E3 F3 G12 A 194 Gr 8M Strain Hardened; bolt size ASME B18.2.1 and
nuts ASME B18.2.2 standard; integral thread UNC-2A stud
and screw nuts ASME B1.1 standard.
PAE-04
(1 1/8 - 2)
B12 B13 B16 Stud bolt; with two hexagonal nuts; bolt stainless steel
C3 C12 C13 ASTM A 193 Gr B8M CL 2; heavy nuts carbon steel ASTM
E3 F3 G12 A 194 Gr 8M Strain Hardened; bolt size ASME B18.2.1 and
nuts ASME B18.2.2 standard; integral thread UN-2A stud
and screw nuts ASME B1.1 standard.
PAE-05
(1/2 - 1)
B9 B10 C9
C10 E9 E10
F10 F10R
G10 G10R
G10P H10
H11
Stud bolt; with two hexagonal nuts; bolt alloy steel ASTM A
193 Gr B16, Zn-Ni (Appendix 10); heavy nuts carbon steel
ASTM A 194 Gr 2H Zn-Ni (Appendix 10); bolt size ASME
B18.2.1 and nuts ASME B18.2.2 standard; integral thread
UNC-2A stud and screw nuts ASME B1.1 standard.
PAE-06
(1 1/8 - 2)
B9 B10 C9
C10 E9 E10
F10 F10R
G10 G10R
G10P H10
H11
Stud bolt; with two hexagonal nuts; bolt alloy steel ASTM A
193 Gr B16, Zn-Ni (appendix 10); heavy nuts carbon steel
ASTM A 194 Gr 2H Zn-Ni (Appendix 10); bolt size ASME
B18.2.1 and nuts ASME B18.2.2 standard; integral thread
UN-2A stud and screw nuts ASME B1.1 standard.
PAE-07
(1/2 -1)
B3 B6 C6 E6
E6R F6 F6R
G3 G6 G6R
H3
Stud bolt; with two hexagonal nuts; bolt alloy steel ASTM A
320 Gr L7 Zn-Ni (Appendix 10); heavy nuts carbon steel
ASTM A 194 Gr 4L Zn-Ni (Appendix 10); bolt size ASME
B18.2.1 and nuts ASME B18.2.2 standard; integral thread
UNC-2A stud and screw nuts ASME B1.1 standard.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
43
of
63
TITLE:
Spec
Description
PAE-08
(1 1/8 - 2)
B3 B6 C6 E6
E6R F6 F6R
G3 G6 G6R
H3
Stud bolt; with two hexagonal nuts; bolt alloy steel ASTM A
320 Gr L7, Zn-Ni (Appendix 10); heavy nuts carbon steel
ASTM A 194 Gr 2H Zn-Ni (Appendix 10); bolt size ASME
B18.2.1 and nuts ASME B18.2.2 standard; integral thread
UN-2A stud and screw nuts ASME B1.1 standard.
BUJ-07
B20
Plug; pipe line; short type; PVC poly vinyl chloride; ASTM D
1784 class 12454; dimensions ASTM D 2464; thread ends
ASME B1.20.1 NPT.
BUJ-08
B21
REDC-01
REDC-02
REDC-04
REDC-05
G10 G11
G14 H10
REDC-06
B13 C13
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
44
of
63
TITLE:
Spec
Description
B12 C12 G12 Concentric reducer; pipe line; stainless steel superduplex;
J12
ASTM A 815 (UNS S32760); ASME B16.9 standard;
buttwelding ends ASME B16.25.
REDC-08
B22 B23
REDC-09
B24
REDC-10
B15
REDC-11
B25
REDC-12
B25
REDC-13
B25
REDC-14
H11 H14
REDC-15
B16
REDC-16
J31
REDC-17
H30
REDC-91
B7 B7R
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
45
of
63
TITLE:
Spec
REDC-92
B7 B7R
Description
Concentric reducer; pipe line; Cu-Ni 90/10 (UNS C7060X);
16 bar pressure; EEMUA 146 standard; ASME B16.9;
buttwelding ends ASME B16.25.
REDE-01
REDE-02
REDE-04
REDE-05
G10 G11
G14 H10
REDE-06
B13 C13
REDE-07
B12 C12 G12 Eccentric reducer; pipe line; stainless steel superduplex;
J12
ASTM A 815 (UNS S32760); ASME B16.9 standard;
buttwelding ends ASME B16.25.
REDE-08
B22 B23
REDE-09
B24
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
46
of
63
TITLE:
Spec
Description
REDE-10
B25
REDE-11
B25
REDE-12
B25
REDE-13
H11 H14
REDE-15
J31
REDE-90
B7
REDE-14
B16
REDE-16
H30
REDE-91
B7R
SAD-03
B22 B23
SAD-04
B24
SAD-05
B22 B23
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
47
of
63
TITLE:
Spec
Description
SAD-06
B24
SKL-91
B7 B7R
T-01A
A4
T-02A
T-02B
T-03
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
48
of
63
TITLE:
Spec
Description
T-05A
T-07A
T-08
B6 C6 E6
E6R
T-09
T-11
T-13
B13 C13
T-15
B13 C13
T-16
B13 C13
T-17
B12 C12 G12 Seamless pipe; stainless steel superduplex; ASTM A 790
J-12
(UNS S32760); ASME B36.19 standard; plain ends.
T-19
B12 C12 G12 Seamless pipe; stainless steel superduplex; ASTM A 790
(UNS S32760); ASME B36.19 standard; buttwelding ends
ASME B16.25.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
49
of
63
TITLE:
Spec
Description
B12 C12 G12 Welded pipe, (E=0,85); stainless steel superduplex; ASTM
A 928 (UNS S32760); ASME B36.19 standard; buttwelding
ends ASME B16.25.
T-21
B15
T-22
B20
T-23
B21
T-24
B25
T-25
B25
T-26
B25
T-27
B22 B23
T-28
B24
T-29
G10 G10P
G11 G14
T-30
T-31
H10
T-32
H11 H14
T-32B
H14
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
50
of
63
TITLE:
Spec
G3
Description
Seamless pipe; stainless steel; ASTM A 312 Gr TP 316L;
ASME B36.19M standard; plain ends.
T-34
G3
T-36
B16
T-37A
B16
T-37B
B16
T-38A
G10P H30
H30P
T-38B
G10P H30
H30P
T-61
B7R
T-62
B7R
T-90
B7 B7R
T-91
B7 B7R
T-92
B7R
TAM-01
A4
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
51
of
63
TITLE:
Spec
Description
TAM-02
TAM-05
TAM-06
B9 B10 B11 Cap; pipe line; carbon steel; ASTM A 105; ASME B16.11
B15 C9 C10 standard; class 6000; socket weld ends.
E9 E10 F4
F10 F10R
F14 G4 G10
G10R G10P
G11 G14
TAM-08
TAM-09
B6 C6 E6
E6R
TAM-12
TAM-19
TAM-20
G3 H3
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
52
of
63
TITLE:
Spec
TAM-21
B13 C13
TAM-22
B12 C12
TAM-23
B20
Cap; pipe line; PVC poly vinyl chloride; ASTM D 1784 class
12454; dimensions ASTM D 2467; plain ends.
TAM-24
B21
TAM-25
TAM-26
TAM-27
Description
B12 C12 G12 Cap; pipe line; stainless steel superduplex; ASTM A 815
J12
(UNS S32760); ASME B16.9 standard; buttwelding ends
ASME B16.25.
TAM-28
G10 G11
G14 H10
TAM-29
G12
TAM-30
H11 H14
TAM-31
H30 H30P
TAM-32
J12
TAM-40
J31
Cap; pipe line; Alloy steel; ASTM A 420 Gr. WPL8; ASME
B16.11 standard; buttwelding ends ASME B16.25
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
53
of
63
TITLE:
Spec
TAM-35
B16
TAM-36
B16
TAM-39
C30 E30
TAM-43
H30
TAM-91
B7 B7R
TAM-93
B7 B7R
TAM-94
B7R
TE-01
A4
TE-02
TE-02P
Description
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
54
of
63
TITLE:
Spec
Description
TE-05
TE-06
B9 B10 B11 Tee; pipe line; carbon steel; ASTM A 105; ASME B16.11
B15 C9 C10 standard; class 6000; socket weld ends.
E9 E10 F4
F10 F10R
F14 G4 G10
G10R G10P
G11 G14
TE-08
TE-09
B6 C6 E6
E6R
TE-12
TE-15
TE-16
G3 H3
TE-17
B13 C13
TE-18
B12 C12
TE-19
B20
Tee; pipe line; PVC poly vinyl chloride; ASTM D 1784 class
12454; dimensions ASTM D 2467; plain ends.
TE-20
B21
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
55
of
63
TITLE:
Spec
Description
TE-22
H11 H14
TE-23
G10 G11
G14 H10
TE-23P
G10P
TE-24
B13 C13
TE-25
B12 C12 G12 Tee; pipe line; stainless steel superduplex; ASTM A 815
J12
(UNS S32760); ASME B16.9 standard; buttwelding ends
ASME B16.25.
TE-25P
G12P
TE-26
B22 B23
TE-27
B24
TE-28
B15
TE-29
B25
TE-30
B25
TE-31
B25
TE-33
G12
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
56
of
63
TITLE:
Spec
TE-34
H30P
TE-35
J12
TE-38
B16
TE-39
B16
TE-41
Description
C30 H30 E30 Tee, pipe line; carbon steel; ASTM A 105; ASME B16.9
standard; buttwelding ends ASME B16.25.
TE-42
H30
TE-42P
H30P
TE-43
J31
Tee, pipe line; Alloy steel; ASTM A 420 Gr. WPL8; ASME
B16.11 standard; buttwelding ends ASME B16.25
TE-91
B7 B7R
TE-93
B7 B7R
TE-94
B7R
TEY-01
B20
TEY-02
B21
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
57
of
63
TITLE:
Spec
THL-91
B7 B7R
TRE-01
TRE-01P
Description
Thredolet; pipe line; Cu-Ni 90/10 (UNS C7060X); EEMUA
146 standard; 20 bar pressure; thread female ends ASME
B1.20.1 NPT.
TRE-02
TRE-03
B9 B10 B11 Reducing tee; pipe line; carbon steel; ASTM A 105; ASME
B15 C9 C10 B16.11 standard; class 6000; socket weld ends.
E9 E10 F4
F10 F10R
F14 G4 G10
G10R G10P
G11 G14
TRE-04
TRE-05
B6 C6 E6
E6R
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
58
of
63
TITLE:
Spec
Description
TRE-08
TRE-10
TRE-11
G3 H3
TRE-12
B13 C13
TRE-13
B12 C12
TRE-14
B20
TRE-15
B21
TRE-16
TRE-17
G10 G11
G14 H10
TRE-17P
G10P
TRE-18
B13 C13
TRE-19
TRE-19P
B12 C12 G12 Reducing tee; pipe line; stainless steel superduplex; ASTM
J12
A 815 (UNS S32760); ASME B16.9 standard; buttwelding
ends ASME B16.25.
G12P
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
59
of
63
TITLE:
Spec
TRE-20
B22 B23
TRE-21
B24
TRE-22
B15
TRE-23
B25
TRE-24
B25
TRE-25
B25
TRE-27
G12
TRE-28
H11 H14
TRE-30
J12
TRE-33
B16
TRE-34
B16 H30P
TRE-35
Description
C30 H30 E30 Reducing tee; pipe line; ASTM A 105; ASME B16.9
standard; buttwelding ends ASME B16.25.
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
60
of
63
TITLE:
Spec
Description
TRE-36
H30
TRE-37P
H30P
TRE-38
J31
Reducing tee; pipe line; Alloy steel; ASTM A 420 Gr. WPL8;
ASME B16.11 standard; buttwelding ends ASME B16.25
TRE-93
B7 B7R
TRE-94
B7R
UN FLEX-01
A4
Flexible union; pipe line; lug nut type; carbon steel; ASTM A
105; 5 degrees maximum angle deflection; integral spherical
seat; maximum pressure 3000 PSI; thread ends API 5B LP.
UN ISOL-01
A4
Pipe union; carbon steel; ASTM A 105; plain seat; dielectricinsulated gasket; class 3000; thread ends ASME B1.20.1
NPT.
UN-01
A4
UN-02
A8
UN-04
UN-05
B9 B10 B11 Pipe union; carbon steel; ASTM A 105; integral conical seat;
B15 C9 C10 class 6000; socket weld ends ASME B16.11.
E9 E10 F4
F10 F10R
F14 G4 G10
G10R G10P
G11 G14
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
61
of
63
TITLE:
Spec
UN-07
B6 C6 E6
E6R
Description
Pipe union; carbon steel; ASTM A 350 Gr LF2 CL1; BS
3799 standard; integral conical seat; class 3000; socket
weld ends ASME B16.11.
UN-09
UN-12
UN-13
G3 H3
UN-14
B13 C13
UN-15
B12 C12
UN-16
B20
UN-17
B21
UN-18
G12
UN-20
J12
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
62
of
63
TITLE:
Spec
Description
UN-23
B16
UN-24
C30 E30
UN-91
B7 B7R
UNADF-91
B7 B7R
UNADM-91
B7 B7R
WOL-01
WOL-02
WOL-04
WOL-05
B12 C12 G12 Weldolet; pipe line; stainless steel; ASTM A 182 Gr F 55
J12
(UNS S32760); MSS SP-97 standard; buttwelding ends
ASME B16.25.
WOL-06
B13 C13
TECHNICAL SPECIFICATION
E&P
N:
DR-ENGP-1.1
SHEET:
63
of
63
TITLE:
Spec
Description
WOL-07
B16
WOL-08
J31
WOL-09
H14
WOL-90
B7 B7R