Beruflich Dokumente
Kultur Dokumente
Frequency Planning
Information
Collection
Link Budget
Network Dimensioning
Output: site number, ideal site location
Pre-Planning
General Process
Simulation based on surveyed site parameter
Output: Engineering parameter table,
Coverage prediction, etc
Detailed
Planning
Cell Planning
Frequency
Planning
ID and
Name
Planning
TA
Planning
PCI
Planning
NB Cell
Planning
X2
Planning
PRACH
Planning
Frequency Planning
1x1 frequency Planning
LTE system works on the same frequency band
Frequency bandwidth utilizing is high
X Interference occurs between the UEs on the edge of a cell
(use same resource)
Frequency Planning
PCI Planning
PCI Planning
In LTE systems, each cell has a physical cell identifier (PCI), enabling UE to differentiate radio signals
of different cells.
In LTE systems, cells are grouped. primary synchronization code (PSC) and secondary
synchronization code (SSC), where the PSC has three values and SSC has 168 values, totaling 504
PCIs.
PCI Planning
Planning principles
Availability: The PCI planning must ensure minimum reuse layers and minimum reuse distance to
avoid possible conflict.
Extensibility: The initial planning must consider the future capacity expansion to avoid frequent
adjustment of the initial planning result. Some PCI groups and some PCIs of in-use PCI groups can
be reserved for future capacity expansion.
Reuse distance: The distance of two cells using the same PCI must meet the minimum reuse distance.
Reuse layers: The number of reuse layers refers to the number of eNodeBs separating the two cells
using the same PCI.
Under normal dual-antenna configuration, separating the PCIs of neighboring cells by modulo 3 of the
PCIs can separate the downlink RS symbols in the frequency domain, improving the accuracy of
channel estimation.
If RS is shifted, then it will help for better performance under low load
Port
1 Antenna
No. of
Antenna port
1
2
4
2
2
2
2* Total No. of RB
4* Total No. of RB
4* Total No. of RB
ports
2 Antenna
RE
No RS transmit
for this antenna port
RS transmitted
or this antenna port
ports
4 Antenna
that of Antenna 1, 2
Antenna Port 0
Antenna Port 1
Antenna Port 2
Antenna Port 3
After
We need to check again about PCI Mod3 result, prevent cochannel interference from same Mod3 result.
PCI Conflict
PCI conflict is classified into PCI collision and PCI confusion
PCI Collision
PCI Confusion
In this case, UEs in the overlapping area of the two cells cannot
implement signal synchronization or decoding.
A PCI confusion occurs between a detected cell and a neighboring cell if the two
cells have the same frequency and PCI and if the reference signal received
power (RSRP) of the two cells reaches the handover threshold.
The PCI confusion may lead to UE handover failures or service drops.
Case :
eNodeB mistakenly considers that the detected cell is cell C and then initiates a
handover to cell C. If the spot that the UE is on is not covered by cell C but cell
B, a handover failure may occur.
If two or more neighboring cells of a cell have the same frequency and PCI,
there is a PCI conflict between these neighboring cells
Planning rule
To reduce PCI mod 3 result competition among neighboring cells to get better
performance under low load situation (referring to following 2 slides)
To avoid PCI mod 30 result competition among neighboring cells to avoid SRS
interfere neighbor cell PRACH
PCI Plan
Sector 1 Sector 2 Sector 3
.
422
335
376
379
377
380
420
423
421
424
422
425
375
378
.
421
334
420
333
480
483
481
484
482
485
161 - 167
141 - 160
126 - 140
111 - 125
1 - 140
SSS/PSS
501
502
503
Border East
Allocation For
Macro (General)
Border Area
WEST/NORTH
Border Area
EAST/SOUTH
Indoor (General)
Spare
Border West
PRACH Planning
The channel used for transmitting the preamble sequence which is needed during UE random
access
ZC root Sequence
Preamble sequence
Preamble sequences of cells are generated through the cyclic shift of the ZC root sequence.
The number of cyclic shift is Ncs
There are 64 PRACH preambles in each LTE cell for Random Access. It is for users randomly selects a
preamble sequence to establish initial connection.
Preambles are generated from root sequence (Zadoff-Chu sequence) and its cyclic shift
838 root sequences are defined by 3GPP with length 839
PRACH Planning
Step 1: Determine Ncs value by the cell radius. (E.g. Assume the cell radius is 9.8 km, take Ncs
value 76)
Step 2: The value of 839/76 is rounded down to 11, that is, each index should generate 11
preamble sequences. In this case, 6 (64/11) root sequence indexes are required to generate 64
preamble sequences.
Step 3: The number of available root sequence indexes is 839/6=139 (0, 6, 12,,6*n,, 828)
Step 4: The available root sequence indexes are assigned to cells. The reuse distance shall be as
far as possible
Huawei will use GENEX U-Net for PRACH planning or using Atoll
TA Planning
A Tracking Area corresponds to the Routing Area (RA) used in UMTS and GSM/Edge Radio Access
Network (URAN and GERAN). The TA consists of a cluster of eNodeBs having the same Tracking
Area Code (TAC)
The TA provides a way to track UE location in idle mode. UE will initials TAL update once cross the
TAL barder in idle mode and will not when cross TA boarder
TAL information is used by the MME when paging idle UE to notify them of incoming data
connections
One TAL can support up to 16 TAs, each TA supports maximum 100 eNodeB in one MME
TAC = Tracking Area Code (1~65533, and 65535) (0 and
65534 are reserved by 3GPP)
TAI = Tracking Area ID = MCC + MNC + TAC
TAL = Tracking Area List
1 TAL = up to 16 TAC
TAL value range: 0~ 65534
Max number of TALs per USN = 20000
TA Planning Principle
When the suburban area and urban area are covered discontinuously, an independent TA is used
for the suburban area.
The mountain or river in the planned area can be used as TA boundary to reduce the overlapping
depth of two TAs. In this way, fewer location updates are performed on the edge of TA.
The LAC planning in the existing 2G/3G networks can serve as a reference for planning TAC
TA Network Design
One TAL is same with one TAC, with this design when the UE in idle condition
then move to another TAC it will be generate TAU to report MME where
is last position for this UE. When there is downlink packet data need to
be deliver for that UE, MME can easily to find latest position.
TAU Procedure
The tracking area update (TAU) procedure is triggered if one of the following
conditions is met:
The UE detects that the current TA does not exist in the TA list on the
UE-registered network.
It is a periodic TAU.
S-GW
Internet
MME
TAU
TAC 2
TAC 1
TAC 4
TAC 3
TA Network Design
S-GW
Internet
One TAL contains multiple TAC, with this design when UE in idle condition
move to different TAC under one TAL there is no TAU. When MME want to
deliver downlink packet data for that UE MME will send to latest TAC where
the UE located. If the UE is unreachable MME will try to paging another TAC
under one TAL until found. This design will take a time compare with the
previous design.
MME
Under
UE move
One TAL
to
new
no need
TAL TAU
need
TAU
TAL 1
TAC 2
TAC 1
TAC 4
TAC 3
TAL 2
Last TAC is 8
but UE move to
TAC 7, MME
will try paging
another TAC
under TAL2
TAC 6
TAC 5
TAC 8
TAC 7
Neighbor Planning
LTE Network require quick hard handover, so the Neighboring cell Planning is very important
LTE Neighboring cell planning content : Intra-Freq Neighboring cell, Inter-freq neighboring cell,
Inter-RAT neighboring Cell
The method of LTE neighbor cell planning is similar to neighbor planning of GSM/WCDMA/CDMA.
Currently, the planning method and tool for LTE are available.
The configuration is different from GSM/WCDMA/CDMA . There is no BSC/RNC in the LTE system. When
an eNB cell is configured as neighbor cells of other eNBs, external cells must be added first, which is
similar to the scenario where inter-BSC/RNC neighbor cells are configured on the BSC. That is, neighbor
cells can be configured only after the corresponding cell information is added.
Site A
Neighbor Cell List
(NCL)
A1
A3
Site B
B3
B1
A2
B2
Site A
A1
A3
Site B
B3
B1
A2
B2
Source
A
A
A
B
B
B
Target
B1
B2
B3
A1
A2
A3