Beruflich Dokumente
Kultur Dokumente
Components: C1 nC8
FP:
PengRobinson
Stream (Tower Feed)
T = 90 oF
P = 217.28 Psia
F = 100 lbmole/hr
xC1= 0.1955
xC2= 0.1462
xC3= 0.1058
xiC4= 0.1076
xnC4= 0.0983
xiC5= 0.0891
xnC5= 0.0768
xnC6= 0.0903
xnC7= 0.0517
xnC8= 0.0387
Column Distillation (Depropanizer)
N = 10
Inlet: TowerFeed (5)
Ovd: Ovhd (total Reflux)
Bttm: Bttms
CondQ dan RebQ
PReb = 205 psia, T = 200 oF (P = 0)
PCond = 200 psia, T = 40 oF (P = 0)
Spec:
Reflux Ratio, Condenser, Molar , 1 (active)
C3inBttms, Reboiler, Mole Fraction, Liquid, 2e-2, Propane (active)
Reboiler duty, Reboiler, 7.5e5 (est)
DEBUTHANIZER
Component:
FP :
Streams
Variable
Temperature (F)
Pressure (Psia)
Flow (lbmole/hr
xC3
xiC4
xnC4
xi-Butene
xiC5
xnC5
nC6
nC7
nC8
Feed1
300
207
247.8
0.028
0.2016
0.2122
0.2419
0.1368
0.1795
0
0
0
Feed2
140
206
145.9
0.0198
0.2124
0.2124
0.0104
0.1409
0.1409
0.0927
0.0942
0.0763
Full
QCond, QReb
Specs:
C5 in Top, Condenser, Mole Fraction, Liquid, 1.798e-2, iC5, nC5
Reboiler Duty, Reboiler, 7.364e6 BTU/hr.
LPG
Feed1
60
600
658.8
0.01
0.01
0.6
0.2
0.1
0.04
0.04
Feed2
60
600
439.2
0.0179
0
0.6244
0.1666
0.1136
0.0431
0.0345
Outlet: SepExit
P = 25 psia
HE (Gas/Gas)
Tube: SepVap CoolGas (P = 10 psia, TCoolGas=43.96)
Shell: LTSVap SalesGas ((P = 10 psia)
Parameter:
Calculate Ft flow
Cooler (Chiller)
CoolGas Cold Gas (Energy: (C3Duty = 1.076e6 BTU/hr)
Separator (LTS)
Inlet: ColdGas
Ovd: LTSVap
Bttm: LTSLiq
Valve (LTSValve)
LTSLiq LTSExit (P = 5 psia)
MIX-101
Inlets: SepExit and LTSExit
Outlet: TowerInlet
Parameter:
Equilize All
Valve (TowerValve)
TowerInlet TowerIn (P = 363 psia)
Heater (Heater)
TowerIn TowerFeed (Energy: HeaterQ, P = 10psi, TTowerFeed = 24.66)
Distillation Column (DePropanizer)
N = 10
Inlet: TowerFeed (5)
Ovd: Ovhd (total Reflux)
Bttm: LiquidProd
CondDuty dan RebDuty
PReb = 202.4 psia, T = 200 oF (P = 0)
PCond = 201.8 psia, T = 40 oF (P = 0)
Spec:
Reflux Ratio, Condenser, Molar , 1 (active)
Propane Fraction, Reboiler, Mole Fraction, Liquid, 2e-2, Propane (active)
Overhead Vapor Rate, Ovhd, Molar, 219.6 (est)
Comp Loop
V101
7 10 (ovd), 8 (bttm)
Level (19.62%)
Tee100
10 11, 13 (Split 11 = 1)
Valve102
89
P9 = 257.6 kPa
Valve101
11 12 (P12 = 257.6 kPa)
RCY1
13 14 (F14=0)
Valve100
14 1
P1 = 98.3
Absorption Dehydration
Component: N2, CO2, H2S, C1, C2, C3, iC4, nC4, iC5, nC5, TEGlycol, H2O
Fluid package: PR
Stream Composition (mol fraction)
Name
Inlet Gas
TEG Feed
Water to
Make UP TEG
Saturate
N2
1.00e-003
CO2
2.84e-002
H2S
1.55e-002
C1
0.8989
C2
3.10e-002
C3
1.48e-002
iC4
5.90e-003
nC4
3.00e-003
iC5
1.00e-003
nC5
5.00e-004
TEGlycol
0.00000
0.99 (%wt)
0.99
H2O
0.00000
0.01
1
0.01
PVT Data
Name
Inlet Gas
TEG Feed
Temperature
(F)
Pressure (Psia)
85
120
900
900
Molar Flow
(lbmole/hr)
1098
8.044
Water to
Saturate
Gas+H2O
85
1.1
Name
Temperature
(F)
Pressure (Psia)
Regen Feed
220
MekeUp TEG
60
TEG To Pump
TEG Only
7
Water DewPt
7.556
895
895
16
Liq Flow
(bbl/d)
Name
Temperature
(F)
Pressure (Psia)
TEG to Recy
120
Saturate (Mixer)
Inlet: Inlet Gas
Water to Saturate
Outlet: Gas+H2O
Equalize All
FWKO (Separator)
Inlet: Gas+H2O
Outlet: Gas to contactor (Vapor)
Water Out
Volume : 70.63Ft3
Liq Level: 50%
T100 (Absorber Column)
Top Stage Inlet:
Bottom Stage Inlet:
Vapor Outlet:
Liquid Outlet:
Number of trays: 14
P1= 885.3 psig
Pn = 885.3 psig
TEG Feed
Gas To Contactor
Dry Gas
Rich TEG
VLV-100 (Valve)
Inlet: Rich TEG
OutLet: LPTEG
L/R Exch (HE)
Tube In:
Tube Out:
Regen Bttms
Lean from L/R
Pump Out
Shell In:
LP TEG
Shell Out:
Regen Feed
HE Design (End Point)
Tube side pressure drop: 0.1 psi
Shell side pressure drop: 10 psi
TEG Regenerator (Dist. Column, 1 stage )
Regen Bttms (Bottom)
Energy: Reb Q
Condenser (Full Reflux)
Sour Gas (Vap)
Energy: Cond Q
Design Spec
TEG bottoms (TEG in battoms, reboiler, liquid, mass fract, 0.99) (active
Reboiler Temperature 400 oF (active)
Reflux Ratio 3.00 (estimate)
Sour Gas Rate 329.4 lbmole/hr (estimate)
MakeUp (Mixer)
Inlet: Lean from L/R
MakeUp TEG
Outlet: TEG to pump
Equilize All
P-100 (Pump)
Inlet: TEG to pump
Outlet: Pump Out
Energy: Pump Q
Adiabatic Eff. 75%
E101 (HE)
Tube In:
Pump Out
Tube Out:
TEG to Recy
Shell In:
Dry Gas
Shell Out:
Sales Gas
HE Design (End Point)
Tube side pressure drop: 10 psi
Shell side pressure drop: 5 psi
Remove TEG (Component Splitter)
Inlet: Sales Gas
Outlet: TEG Only (Ovd)
Water DewPt (Bttm)
Energy: Split Q
Split All zero except TEG Only=1
V-101 (Separator)
Inlet: Water DewPt
Out: