Beruflich Dokumente
Kultur Dokumente
Switch 1
Switch>en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname SW1
SW1(config)#int f0/1
SW1(config-if)#no shut
SW1(config-if)#switchport mode trunk
SW1(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
SW1#wr
Building configuration...
[OK]
SW1#
Switch 2
witch>en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname SW2
SW2(config)#int fa0/1
SW2(config-if)#no shut
SW2(config-if)#switchport mode trunk
SW2(config-if)#int fa0/2
SW2(config-if)#no shut
SW2(config-if)#switchport mode trunk
SW2(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
SW2#wr
Building configuration...
[OK]
SW2#
Switch 3
Switch>en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname SW3
SW3(config)#int fa0/1
SW3(config-if)#no shut
SW3(config-if)#switchport mode trunk
SW3(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
SW3#wr
Building configuration...
[OK]
SW3#
VLAN Configuration:
VLAN Creation:
Switch 1
SW1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SW1(config)#va
SW1(config)#vlan 2
SW1(config-vlan)#name sales
SW1(config-vlan)#exit
SW1(config)#vlan 3
SW1(config-vlan)#name HR
SW1(config-vlan)#exit
SW1(config)#vlan 4
SW1(config-vlan)#name IT
SW1(config-vlan)#^Z
%SYS-5-CONFIG_I: Configured from console by console
SW1#wr
Building configuration...
[OK]
SW1#
Switch 2
SW2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SW2(config)#vlan 2
SW2(config-vlan)#name sales
SW2(config-vlan)#exit
SW2(config)#vlan 3
SW2(config-vlan)#name HR
SW2(config-vlan)#exit
SW2(config)#vlan 4
SW2(config-vlan)#name IT
SW2(config-vlan)#^Z
%SYS-5-CONFIG_I: Configured from console by console
SW2#wr
Building configuration...
[OK]
SW2#
Switch 3
SW3#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SW3(config)#vlan 2
SW3(config-vlan)#name sales
SW3(config-vlan)#exit
SW3(config)#vlan 3
SW3(config-vlan)#name HR
SW3(config-vlan)#exit
SW3(config)#vlan 4
SW3(config-vlan)#name IT
SW3(config-vlan)#^Z
%SYS-5-CONFIG_I: Configured from console by console
SW3#wr
Building configuration...
[OK]
SW3#
Switch 1
SW1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SW1(config)#int range fa0/2-5
SW1(config-if-range)#no shut
SW1(config-if-range)#switchport mode access
SW1(config-if-range)#switchport access vlan 2
SW1(config-if-range)#int range fa0/6-12
SW1(config-if-range)#no shut
SW1(config-if-range)#switchport mode access
SW1(config-if-range)#switchport access vlan 3
SW1(config-if-range)#int range fa0/13-18
SW1(config-if-range)#no shut
SW1(config-if-range)#switchport mode access
SW1(config-if-range)#switchport access vlan 4
SW1(config-if-range)#^Z
%SYS-5-CONFIG_I: Configured from console by console
SW1#wr
Building configuration...
[OK]
SW1#
Switch 2
SW2#
SW2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SW2(config)#int range fa0/3-5
SW2(config-if-range)#no shut
SW2(config-if-range)#switchport mode access
SW2(config-if-range)#switchport access vlan 2
SW2(config-if-range)#int range fa0/6-12
SW2(config-if-range)#no shut
SW2(config-if-range)#switchport mode access
SW2(config-if-range)#switchport access vlan 3
SW2(config-if-range)#int range fa0/13-18
SW2(config-if-range)#no shut
SW2(config-if-range)#switchport mode access
SW2(config-if-range)#switchport access vlan 4
SW2(config-if-range)#^Z
%SYS-5-CONFIG_I: Configured from console by console
SW2#wr
Building configuration...
[OK]
SW2#
Switch 3
SW3>
SW3>en
SW3#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SW3(config)#int range fa0/2-5
SW3(config-if-range)#no shut
SW3(config-if-range)#switchport mode access
SW3(config-if-range)#switchport access vlan 2
SW3(config-if-range)#int range fa0/6-12
SW3(config-if-range)#no shut
SW3(config-if-range)#switchport mode access
SW3(config-if-range)#switchport access vlan 3
SW3(config-if-range)#int range fa0/13-18
SW3(config-if-range)#no shut
SW3(config-if-range)#switchport mode access
SW3(config-if-range)#switchport access vlan 4
SW3(config-if-range)#^Z
%SYS-5-CONFIG_I: Configured from console by console
SW3#wr
Building configuration...
[OK]
SW3#
Switch 1
w1>
Sw1>en
Sw1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Sw1(config)#int f
Sw1(config)#int fa0/24
Sw1(config-if)#no shut
Sw1(config-if)#switchport mode trunk
Sw1(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
Sw1#wr
Building configuration...
[OK]
Sw1#
Router 1:
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname Router1
Router1(config)#int fa0/1
%Invalid interface type and number
Router1(config)#int fa0/0
Router1(config-if)#no shut