Beruflich Dokumente
Kultur Dokumente
Chassis : C15C(REV.2)
Model : TE14N53X/XEU TX14B3F3X/SEC
TX20C33X/XET TX20C3DF3X/XET
TX20C5DF3X/SEC TX21B5DF3X/SEC
2. Specifications
6. Troubleshooting
9. Block Diagram
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential
hazards such as electrical shock and X-rays.
Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between
the servicing and safety precautions, always follow the safety precautions.
Warning2: An electrolytic capacitor installed with the wrong polarity might explode.
1. Servicing precautions are printed on the 5. Check the insulation between the blades of the
cabinet. Follow them. AC plug and accessible conductive parts
(examples: metal panels, input terminals and
2. Always unplug the unit’s AC power cord from earphone jacks).
the AC power source before attempting to: (a)
Remove or reinstall any component or 6. Insulation Checking Procedure: Disconnect the
assembly, (b) Disconnect an electrical plug or power cord from the AC source and turn the
connector, (c) Connect a test component in power switch ON. Connect an insulation
parallel with an electrolytic capacitor. resistance meter (430V) to the blades of the AC
plug.
3. Some components are raised above the printed
circuit board for safety. An insulation tube or The insulation resistance between each blade
tape is sometimes used. The internal wiring is of the AC plug and accessible conductive parts
sometimes clamped to prevent contact with (see above) should be greater than 1 megohm.
thermally hot components. Reinstall all such
elements to their original position. 7. Never defeat any of the B+ voltage interlocks.
Do not apply AC power to the unit (or any of
4. After servicing, always check that the screws, its assemblies) unless all solid-state heat sinks
components and wiring have been correctly are correctly installed.
reinstalled. Make sure that the portion around
the serviced part has not been damaged. 8. Always connect a test instrument’s ground
lead to the instrument chassis ground before
connecting the positive lead; always remove
the instrument’s ground lead last.
1. Some semiconductor (“solid state”) devices 5. Use only a grounded-tip soldering iron when
are easily damaged by static electricity. Such soldering or unsoldering ESDs.
components are called Electrostatically
Sensitive Devices (ESDs); examples include 6. Use only an anti-static solder removal device.
integrated circuits and some field-effect Many solder removal devices are not rated as
transistors. The following techniques will “anti-static”; these can accumulate sufficient
reduce the occurrence of component damage electrical charge to damage ESDs.
caused by static electricity.
7. Do not remove a replacement ESD from its
2. Immediately before handling any semicon protective package until you are ready to
ductor components or assemblies, drain the install it. Most replacement ESDs are
electrostatic charge from your body by packaged with leads that are electrically
touching a known earth ground. Alternatively, shorted together by conductive foam,
wear a discharging wrist-strap device. (Be aluminum foil or other conductive materials.
sure to remove it prior to applying power—
this is an electric shock precaution.) 8. Immediately before removing the protective
material from the leads of a replacement ESD,
3. After removing an ESD-equipped assembly, touch the protective material to the chassis or
place it on a conductive surface such as circuit assembly into which the device will be
aluminum foil to prevent accumulation of installed.
electrostatic charge.
9. Minimize body motions when handling
4. Do not use freon-propelled chemicals. These unpackaged replacement ESDs. Motions such
can generate electrical charges that damage as brushing clothes together, or lifting a foot
ESDs. from a carpeted floor can generate enough
static electricity to damage an ESD.
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
ASSY-KOREA
REMOCON
1 * AA95-01371A ASSY-KOREA;,C15C,TVCR20
1 AA59-00221E REMOCON;,TM66,SAA5554PS,38,G6671B,S/S,
2 AA27-20003Y COIL-DEGAUSSING;-,20,15.2ohm,28T,L2170,
2 AA98-00080B ASSY TBC WIRE(P);DP,20inch,AA98-00051B,2
3 AA98-00051B ASSY TBC WIRE(P);-,20inch,PAL,2P,C15C
2 AA60-10050R SCREW-ASSY;WC,HH,+,M5,L31.5,SWRCH18A,ZPC
2 0202-000187 SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb
2 AA65-30008A CLAMP-CORD;-,PE,HB,BLK,-,-
2 AA65-30009A CLAMPER FBT C;TVCR 14/20/21
2 AA65-30013A CLAMPER WIRE;TVCR 20
2 AA65-30018A CLAMP-WIRE;NYLON-66,-,-,DATL-600,DONG-A,
2 AA65-30107A CLAMP-D,COIL;NYLON 66,V2,NTR,-,20~22 INC
ASSY-LOCAL
1 AA95-01372A ASSY-LOCAL;,C15C,TVCR20
CABINET BACK
1 AA64-00323A CABINET BACK;TVCR TVI 20 PLATEADO
POWER CORD
1 AA96-20013B POWER CORD; TVCR EUROPE BLACK
1 AA64-01153F DOOR-HOUSING;-,ABS,HB,SILVER,-,-,-
1 AA40-10006MTUNER-F/S;TECC2949PG29A(S),PAL-B/G,TR,18
8-2 TX20C3DF3X/XET
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
3 J302 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 J941 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm
3 J305 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 ZK03 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm
3 J306 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 IC901S AA09-00090A IC MICOM;SAA5565PS/M3-0259,SPM-738EEM1,3.3V,ILDE
3 J307 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 HC002 AA13-00087A IC HYBRID;-,TAR001,SIP,10P,-,BK
3 J308 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 HC001S AA13-20004WIC-HYBRID;-,PAP103T,SIP,6P,PRE-AMP,TP
3 J309 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 T801S AA26-20007U TRANS-SWITCHING;-,90~260V,125V/16.5V/9.5V,-,EE
3 J311 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 T444S AA26-30001Y TRANS-FLYBACK;-,FSV-20A001,20,125V
3 J312 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 T401 AA26-50001B TRANS-HORIZ.DRIVE;-,-,-,7.1mH,-,-,102uH,-,-,-,-,-,
3 J313 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 LP801S AA27-00116A COIL CHOKE;CODE_NO,-,35mH,-0, +5%,-,2.8OHM,1.2A,-,
3 J314 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 LR401S AA27-30001B COIL-LINEARLITY;-,195uH,QIC1010,PI0.4,4.5x21.5
3 J315 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 LX801S AA29-30001C FILTER-LINE NOISE;-,39mH,1.0A,-,-
3 J607 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 TU02S AA40-10006T TUNER-F/S;TECC2849PG29A(S),PAL-B/G,TR,18
3 J610 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 TU01S AA40-10006V TUNER-F/S;TECC2949PG30B(S),PAL-B/G,TR,18
3 J612 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 PCB AA41-00431A PCB-MAIN;TF21B5,FR-1,1L,A,1.6T,330X245,C15C,1A
3 J614 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 - AA60-10008A SCREW-TAPPING;-,SWRCH18A,M3,L10,TH,+,-,-,ZPC(YEL),
3 J616 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY01 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J620 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY02 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J701 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY03 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J703 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY04 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J705 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY05 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J706 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY06 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J707 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY07 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J708 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY08 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J711 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY09 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J712 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY10 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J713 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY100 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J715 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY11 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J716 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY14 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J720 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY15 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J724 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY16 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J725 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY17 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J726 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY19 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J727 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY20 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J728 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY21 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J729 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY22 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J730 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY23 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J731 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY24 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J732 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY25 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J733 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY26 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J734 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY27 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J735 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY28 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J737 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY29 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J739 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY30 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J740 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY31 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J741 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY32 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J833 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY33 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J901 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY34 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J902 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY35 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J903 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY36 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J905 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY37 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J906 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY38 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J907 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY39 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J909 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY40 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J911 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY41 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J912 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY42 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J913 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY43 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J914 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY44 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J915 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY45 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J917 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY47 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J918 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY48 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J919 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY49 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J920 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY50 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J921 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY51 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J922 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY52 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J923 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY53 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J924 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY54 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J927 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY55 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J930 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY56 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J931 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY57 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J932 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY58 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J933 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY59 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J934 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY60 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J935 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY61 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J936 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY62 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J937 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY63 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J939 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY64 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J940 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY65 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
ASSY-KOREA
1 * AA68-50056Z LABEL GEMSTAR;TVCR EUROPA
1 * AA95-01371A ASSY-KOREA;,C15C,TVCR20
8-3 TX20C5DF3X/XEC
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
3 J305 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 ZK03 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm
3 J306 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 IC901S AA09-00090A IC MICOM;SAA5565PS/M3-0259,SPM-738EEM1,3.3V,ILDE
3 J307 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 HC002 AA13-00087A IC HYBRID;-,TAR001,SIP,10P,-,BK
3 J308 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 HC001S AA13-20004WIC-HYBRID;-,PAP103T,SIP,6P,PRE-AMP,TP
3 J309 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 T801S AA26-20007U TRANS-SWITCHING;-,90~260V,125V/16.5V/9.5V,-,EE
3 J311 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 T444S AA26-30001Y TRANS-FLYBACK;-,FSV-20A001,20,125V
3 J312 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 T401 AA26-50001B TRANS-HORIZ.DRIVE;-,-,-,7.1mH,-,-,102uH,-,-,-,-,-,
3 J313 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 LP801S AA27-00116A COIL CHOKE;CODE_NO,-,35mH,-0, +5%,-,2.8OHM,1.2A,-,
3 J314 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 LR401S AA27-30001B COIL-LINEARLITY;-,195uH,QIC1010,PI0.4,4.5x21.5
3 J315 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 LX801S AA29-30001C FILTER-LINE NOISE;-,39mH,1.0A,-,-
3 J607 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 TU02S AA40-10006T TUNER-F/S;TECC2849PG29A(S),PAL-B/G,TR,18
3 J610 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 TU01S AA40-10006V TUNER-F/S;TECC2949PG30B(S),PAL-B/G,TR,18
3 J612 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 PCB AA41-00431A PCB-MAIN;TF21B5,FR-1,1L,A,1.6T,330X245,C15C,1A
3 J614 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 - AA60-10008A SCREW-TAPPING;-,SWRCH18A,M3,L10,TH,+,-,-,ZPC(YEL),
3 J616 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY01 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J620 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY02 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J701 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY03 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J703 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY04 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J705 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY05 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J706 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY06 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J707 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY07 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J708 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY08 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J711 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY09 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J712 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY10 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J713 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY100 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J715 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY11 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J716 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY14 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J720 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY15 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J724 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY16 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J725 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY17 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J726 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY19 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J727 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY20 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J728 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY21 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J729 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY22 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J730 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY23 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J731 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY24 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J732 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY25 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J733 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY26 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J734 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY27 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J735 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY28 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J737 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY29 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J739 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY30 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J740 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY31 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J741 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY32 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J833 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY33 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J901 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY34 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J902 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY35 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J903 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY36 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J905 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY37 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J906 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY38 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J907 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY39 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J909 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY40 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J911 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY41 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J912 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY42 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J913 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY43 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J914 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY44 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J915 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY45 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J917 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY47 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J918 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY48 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J919 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY49 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J920 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY50 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J921 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY51 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J922 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY52 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J923 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY53 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J924 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY54 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J927 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY55 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J930 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY56 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J931 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY57 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J932 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY58 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J933 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY59 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J934 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY60 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J935 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY61 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J936 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY62 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J937 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY63 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J939 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY64 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J940 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY65 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
3 J941 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3 EY66 AA60-40011A EYELET;ID2.0,OD2.8,-,-,BST,-
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
2 AA27-20003Y COIL-DEGAUSSING;-,20,15.2ohm,28T,L2170,
2 AA98-00080B ASSY TBC WIRE(P);DP,20inch,AA98-00051B,2 1 * AA40-00069A TUNER;TEDE9-802A,PAL,181CH,38.9MHZ,7
3 AA98-00051B ASSY TBC WIRE(P);-,20inch,PAL,2P,C15C
2 AA60-10050R SCREW-ASSY;WC,HH,+,M5,L31.5,SWRCH18A,ZPC
2 0202-000187 SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb 1 * AA91-00782A ASSY-S-IMP ROLLER;,PAL 2HD SESA,TF14N53,
2 AA65-30008A CLAMP-CORD;-,PE,HB,BLK,-,-
2 AA65-30009A CLAMPER FBT C;TVCR 14/20/21
2 AA65-30013A CLAMPER WIRE;TVCR 20
2 AA65-30018A CLAMP-WIRE;NYLON-66,-,-,DATL-600,DONG-A,
2 AA65-30107A CLAMP-D,COIL;NYLON 66,V2,NTR,-,20~22 INC
8-4 TX21B5DF3X/SEC
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
POWER CORD
1 * AA96-20013B POWER CORD; TVCR EUROPE BLACK
REMOCON
1 * AA59-00221B REMOCON;,TM66,SAA5554PS,43,G6671B,S/S,
1 * AA40-00071A TUNER;TEDE9-247A,PAL,181CH,38.9MHZ,7
1 * AA40-00069A TUNER;TEDE9-802A,PAL,181CH,38.9MHZ,7
1 * AA64-01141A DOOR-;-,ABS,HB,-,-,-,-
1 * AA39-30007A IF-CABLE;-,T,100mm,1365#26
8-5 TE14N53X/XEU
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
1 * AA64-01141F DOOR-;-,ABS,HB,-,-,-,-
ASSY-KOREA
1 * AA95-01369A ASSY-KOREA;,C15C,TVCR14
2 AA27-20003U COIL-DEGAUSSING;-,14,16.4ohm,75T,890mm,
2 AA98-00024A ASS’Y TBC WIRE;TVCR 14 C15A-C (PACK)
3 AA98-00023A ASS’Y TBC WIRE;TVCR 14 C15A-C (PIECE)
2 AA60-10050R SCREW-ASSY;WC,HH,+,M5,L31.5,SWRCH18A,ZPC
2 0202-000187 SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb
2 3001-001015 SPEAKER;2.5W,16ohm,88dB,150Hz
2 AA39-20501A LEAD CONNECTOR-ASSY;-,67096-003,REC,3(2)
2 AA42-10001V ANT-ROD;-,3S,620MM,BRN,UL/CSA
2 AA26-90001C TRANS-MATCHING;-,300ohm/75ohm,PAL,40-890
2 AA63-10002A BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,-,-
2 AA65-30008A CLAMP-CORD;-,PE,HB,BLK,-,-
2 AA65-30009A CLAMPER FBT C;TVCR 14/20/21
2 AA65-30016A CLAMP-D,COIL;-,NYLON-66,V0,NTR,DADH-360,
2 AA65-30018A CLAMP-WIRE;NYLON-66,-,-,DATL-600,DONG-A,
ASSY-LOCAL
1 * AA95-01368A ASSY-LOCAL;,14N5,C15C,TVCR14
8-6 TX14B3F3X/SEC
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
1 * AA95-01369A ASSY-KOREA;,C15C,TVCR14
1 * AA64-01150B DOOR-HOUSING;-,ABS,HB,-,-,-,-
2 AA27-20003U COIL-DEGAUSSING;-,14,16.4ohm,75T,890mm,
2 AA98-00024A ASS’Y TBC WIRE;TVCR 14 C15A-C (PACK)
3 AA98-00023A ASS’Y TBC WIRE;TVCR 14 C15A-C (PIECE)
2 AA60-10050R SCREW-ASSY;WC,HH,+,M5,L31.5,SWRCH18A,ZPC
2 0202-000187 SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb
2 3001-001015 SPEAKER;2.5W,16ohm,88dB,150Hz
2 AA39-20501A LEAD CONNECTOR-ASSY;-,67096-003,REC,3(2)
2 AA42-10001V ANT-ROD;-,3S,620MM,BRN,UL/CSA
2 AA26-90001C TRANS-MATCHING;-,300ohm/75ohm,PAL,40-890
2 AA63-10002A BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,-,-
2 AA65-30008A CLAMP-CORD;-,PE,HB,BLK,-,-
2 AA65-30009A CLAMPER FBT C;TVCR 14/20/21
2 AA65-30016A CLAMP-D,COIL;-,NYLON-66,V0,NTR,DADH-360,
2 AA65-30018A CLAMP-WIRE;NYLON-66,-,-,DATL-600,DONG-A,
ASSY-LOCAL
1 * AA95-01367A ASSY-LOCAL;,B5,C15C,TVCR14
TP01
TP03
TP04
TP03
TP05
TP06
TP01
TP02
TP03
TP04
TP05
: Power Line
: Signal Line
TP5 TP4
TP02
TP03
TP6
TP3
TP04
TP2
TP1
TP05
TP06
: Power Line
: Signal Line
TP01 TP02
TP03 TP04
TP 8 TP 7
TP05 TP06
TP07 TP07
: Power Line
: Signal Line
: Power Line
: Signal Line
: Power Line
: Signal Line
: Power Line
: Signal Line
11-11 IF (MONO) 11-12 CRT 11-13 2'nd IF PAL/SECAM-B/G, D/K, I OPTION (MONO)
TP3
TP2
TP1
: Power Line
: Signal Line
: Power Line
: Signal Line
ICM301
ICM901 ICM602
PLAY REC STOP PLAY REC STOP PLAY REC STOP ICM601
1 2.5 2.5 2.5 34 1.8 1.8 1.8 67 4 4 4 PLAY REC STOP PLAY REC STOP
PLAY REC STOP PLAY REC STOP PLAY REC STOP
2 2.5 2.5 2.5 35 3.5 3.5 3.5 68 0 0 0 1 4 0.8 0.8 1 0.9 0.9 0
1 5 5 5 34 0 0 0 67 5 0 0
3 2.5 2.5 2.5 36 1.8 1.8 2 69 0.7 0.7 0.7 2 2 2 2 2 2.6 2.6 0
2 0 0 0 35 0 0 0 68 0 0 0
4 2.5 2.5 2.5 37 4.9 4.9 5 70 2 2 2
3 5 5 5 36 0 0 0 69 5 5 5 3 4 4 4 3 5.2 5.2 5.2
5 2.5 2.5 0 38 1.8 1.8 1.8 71 2.5 2.5 2.5 37 0 0 0 70 5 5 5
4 5 5 5
6 2.5 2.5 2.5 39 4 4 4 72 0.3 2.5 3
4 3.5 3.5 3.5 4 2.6 2.6 2.6
5 5 5 5 38 5 5 5 71 0 0 0
7 2.5 2.5 2.5 40 5 5 5 73 2.5 2.5 3.5 6 5 5 5 39 5 5 5 72 1.8 1.8 1.8 5 0 0 0 5 2.6 2.6 2.6
8 0 0 0 41 2.7 2.7 3 74 2 0 2 7 5 5 5 40 0 0 0 73 0 0 0 6 0 0 0 6 2.6 2.6 2.6
9 0 0 0 42 3 3 3.2 75 5 5 5 8 5 5 5 41 5 5 5 74 0 0 0 7 0 0 0 7 5 5 0
10 1.6 1.6 2 43 1.9 1.9 2 76 2.5 2.5 2.5 9 5 5 0 42 5 5 5 75 0 0 0
10 5 5 0 43 5 5 5 76 0.7 0.7 0.7
8 2.5 2.5 2.5 8 5 5 0
11 3.2 3.2 3.2 44 4.3 4.3 0 77 0 0 0
12 5 2 2.5 45 1.8 1.8 2 78 2.5 2.5 0 11 0 0 0 44 5 5 5 77 0.7 0.7 0.7 9 2.5 2.5 2.5 9 12.5 12.5 13
12 0 0 0 45 0 0 0 78 0 0 0 10 2.5 2.5 2.5 10 0 0
13 1.5 1.5 2 46 1.5 1.4 1.5 79 2.5 2.5 2.5 0
13 0 0 0 46 0 0 0 79 0 0 0
14 1.5 1.5 1.6 47 2 2 9 80 2.5 5 2.5 11 2.5 2.5 2.5 11 5 5 5.1
14 5 5 5 47 0 0 0 80 0 0 0
15 2.2 2.2 2.2 48 2.3 2.3 2.2 81 0 0 0 12 4.5 4.5 4.5 12 5 5 5.1
15 3.5 3.5 3.5 48 5 5 5 81 3 0 0
16 5 5 5 49 1.2 1.2 1 82 1.8 4.1 1 49 5 5 5 82 4 0 0
16 4.5 4.5 4.5 13 2.5 2.5 2.5 13 0 0 0
17 3 0 0 50 0 0 0 83 0 0 0 17 0 0 0 50 5 5 5 83 0 0 0
18 1.8 2.1 2.2 51 1.9 1.9 0 84 1.8 4.1 1
14 2.5 4.7 4.5 14 0 0 0
18 4.5 4.5 4.5 51 5 5 5 84 0 0 0
19 2.1 2.1 2.2 52 2.4 2.4 2.5 85 1.8 4.1 1 19 3.5 3.5 3.5 52 5 5 5 85 2.5 5 2.5 15 3 2.5 2.5 15 0 0 0
20 2.8 2.8 3.2 53 0 0 0 86 0 0 0 20 5 5 5 53 5 5 5 86 2.5 5 2.5 16 5 1 1 16 8.4 8.8 0
21 2.1 2.1 2.5 54 2.4 2.4 2.5 87 5 5 5 21 0 0 0 54 5 5 5 87 2.5 2.5 2.5
17 2.5 2.5 2.5 17 8.4 8.8 0
22 0 0 0 55 5 5 5 88 1.8 4.1 2 22 0 0 0 55 0 5 0 88 2.5 2.5 2.5
23 5 5 0 56 0 0 0 89 2.5 2.5 2.5 18 2 2 2 18 8.4 8.8 0
23 5 5 5 56 3.5 3.5 0 89 0 0 0
24 5 5 5 57 3.4 3.4 3.5 90 1.8 4.1 2
24 5 5 0 57 0 0 0 90 2.5 2.5 2.5 19 2.5 2.5 2.5 19 5.2 5.2 0
25 5 5 0 58 5 5 5 91 0 0 0
25 1.8 1.8 2.8 58 5 5 5 91 1.8 4.1 2 20 2.5 2.5 2.5 20 0 0 0
26 0 0 0 59 5 5 5 92 5 5 5
26 0.8 0 1 59 3.4 3.4 3.5 92 4 1.6 0
27 5 5 5 60 5 5 5 93 5 5 5
21 2.5 2.5 2.5 21 12.5 12.5 13
27 4.1 4.1 4.1 60 3.5 3.5 3.5 93 4 4.0 0 22 5 5 5 22 0
28 5 5 5 61 5 5 5 94 0 5 0 8.4 8.2
28 4.1 4.1 4.1 61 3.3 3.3 3.5 94 0.5 0.7 0 29 5 5 0 62 0 0 0 95 0 0 0 23 3 3 3 23 8.4 8.2 0
29 0.8 0.8 3 62 3.5 3.5 3.5 95 0 0 0 30 0 0 0 63 0 0 0 96 5 5 5
30 1 0 1 63 4 4 0 96 2.5 2.5 2.5 64 5 5 5 97 5 5 5
24 3 3 3 24 8.4 8.2 0
31 0 0 0
31 2.1 2.1 3.5 64 2.2 2.2 0 97 0 0 0 32 5 5 5 65 0 0 0 98 5 5 0 25 4.1 3 3 25 1.8 1.8 2.6
32 1.8 1.8 2 65 2.4 2.4 2.2 98 2.5 2.5 2.5 33 0 0 0 66 0 5 0 99 5 5 0 26 5 0 0 26 1.8 1.8 0
33 2 2 1.5 66 2.5 2.5 3 99 5 4.3 5 100 5 5 5
27 4.1 4.1 4.1 27 1.4 1.4 1
100 2.5 2.5 2.5
28 3.1 3.1 3.1 28 2.4 2.5 2
27 5.2 5.2 0
28 0 0 0
9. Block Diagrams
9-1-1 Notes
The TV’s 1st and 2nd tuners (and VCR module) are “multi-system.” compatible:
IC201 (TDA8842/8841) is the video, chroma, and deflection (VCD) IC .
If the output PB signal of micom pin 6 is high, the PB signal outputs from module deck 2, passes
through IC 702 pins 2 and 3 and out to another VCR . The output signal of IC701 pin 1 (pin 15)
outputs from IC201S pin 17 .
The output CVBS (Composite Video Signal) of the 2nd IF outputs to IC702pin 3 when the micom’s pin 7
V/T/H (VCR tuner high) is high . The decoded signal goes to IC701 pin 2, where it is fed to IC 701 pin
4 (high output of micom’s’ pin 8— AV/Tuner), and out to VCR pin 4 (module deck) for recording.
The output CVBS of the 2nd IF is fed from IC701 pin 5 to IC701 pin 4 (low output of micom
pin 8—AV/tuner). Then it goes to the module deck pin 4 for recording.
The scrambled signal (CVBS) is fed to IC702 pin 1 through the 1st IF, and then to IC702 pin 3 (micom’s
pin 7, V/T/H registers low). Then it goes to the decoder input. The descrambled signal goes to IC701
pins 2 and 15 (PH high output of micom’s pin 6), and then to IC201S pin 17, where it outputs as RGB.
The viewer sees the signal from the 1st tuner , while the signal from the second tuner is recorded.
Audio processing for the French system type is shown in the table.
ANT ICT01
#8
MICOM#24 SDA TTX
R
1st CRT
1st Tunning G Drive
IF
IF B
DET.
INT EXT
6 13 17
IC702
9 PB H Micom #6
Trap
2 10 V/T/H Micom #7
1T.option
1 3
2nd Tunning 2nd
IF
5
Micom #6 10
L V-out VCR
H or
1 2
Decorder
#13
5 3
VPS
ICP01 Micom #8
9 4
CN101 PB.V 2
AV/Tuner
Module CN101
DECK 4 REC. SOURCE V.
ANT
MICOM#24 SDA
SPK
1st 15
1st Tunning IF
IF PROCESS
INT EXT A
6 1 55 2
14 IC701
ZK01
2nd ZK02 HC002
2nd Tunning 13
IF A-0 H
11 Micom #5
C15COPTION
12
S/L (AM)
MICOM14 BG/I L ZK03 EXT A out VCR
MICOM15 DK/L ZK04 or
Decoder A in
REC. SOURCE A.(TUNER)
8 CN101
REC. SOURCE A.(EXT)
6
Module
DECK PB.A
10
om
EXT.A pti
.o
IF IN 11 7 1T 14 13
Switch
B 1T.A L
9 12 9 H Micom #5
Micom #17 S-L CTL 10 L
15 10 H Micom #7
(AM) S-L A C 5
1T.A IC702
B/G (FM)
ANT
OPTION
2F EXT- L
TDA
1 Tuner EXT- R 7297
Nicam Module
MSP 3410 INT- L
IC601
INT- R
IC602
SDA
MICOM
2Tuner R
2Tuner L
EXT- R
EXT- L
SCL PB PB
L R
Decoder
2Tuner
REC - L Module EXT- L
IF Module
REC - R Deck EXT- R
TDA9874
7-2 21B5
7-3 14B5
7-4 14N5
The descriptions and characteristics given in this booklet are given for information purposes only and
are subject to modification without notice.
TELEVISION PART
Colour systems PAL(option) / SECAM(option) (UK;PAL)
TV standards L/L’(option), B/G(option), D/K(option) (UK;I)
Number of channels 100 programmes
Reception range/cable TV Hyperband/interband tuner
Aerial input 75 Ohms, coaxial cable
VCR PART
Format VHS standard
(PAL / SECAM(option) / MESECAM(option) / NTSC in playback only)
Heads Video: 2 rotary heads, LP(option), 4 Heads(option)
Audio/Control: 1 stationary head (linear)
Erase: 1 full track erase head
System Video Normal CCIR
System Audio Mono / NICAM&A2-STEREO
Luminance FM azimuth recording
Colour Down converted subcarrier phase shifted direct recording
FF/REW time Less than 100 seconds in FF with E-120
Wow and flutter (WTD) 0.4% maximum (SP)
Frequency response 100 Hz - 8 KHz
GENERAL
Power supply 220-240V~, 50Hz (110-260V~, 50/60Hz; option),(160-300V~50/60Hz;Russia)
Consumption 14”15” (60W)
20”/21” (90W)
Audio output power 14”15” (1.5W)
20” (3W)
21” (1.5Watts x 2)
Number of loudspeakers 14”/15”/20” (1)
21” (2)
Tube size 14” (37cm/34cmV)
15” (39cm/36cmV)
20” (51cm/48cmV)
21” (55cm/51cmV)
Tube type BLACK MATRIX
Sockets 1 full RGB SCART on the rear
1 RCA input (audio and video) on the front
Earphones output (3.5 mm mini-jack)
1 aerial/cable TV coaxial input
Dimensions (W x D x H) 14” (368.5 x 388 x 381)
15” (411 x 401 x 417)
20” (488 x 477 x 488)
21” (520 x 495 x 508)
Weight 14” (11.7 kg)
15” (14.8 kg)
20” (20.4 kg)
21” (23.2 kg)
Operating temperature 5°C - 40°C (41°F - 104°F)
Relative humidity 10% - 75%
3-1 Disassembly
1. Remove 3 screws from the Main Assembly. Remove the dust cover.
1. Remove 2 screws holding the bottom cover. 1. Remove 2 screws holding the upper chassis
housing.
2. Remove one screw from Main PCB
Assembly. Take off the deck Assembly. 2. Remove 3 screws holding the deck assembly.
6. Troubleshooting
Check
both terminal voltages
of C820 (125V)
No Yes
Check D801~804
F801,Q801. Check whether
Yes each power line Yes
is short or open.
No No Is IC901
Is Q801 Pin 3
19~22V? Pin 64 Voltage 5V?
Check/Replace
T801.
No Check H.V SYNC on
IC901 Pins 1, 2
Check/Replace
IC901. Yes
Check
No IC901 Pin 3 is High
when power is On.
Check/Replace
IC902.
Yes
Yes
Check CN102
Retouch CN102 or
Replace CN102
No
Check IC901 #64
Yes No
Check IC804
Check Q801 No
Replace
Yes
Check D801~D805
Check IC901 #28~31 Yes
No
No
Check/Replace
D801~D805
Replace
IC901
No
Check IC901 #23, #24
Yes
Yes Check Another I2C No
bus line
Check After
No bus line open
Check D834 "H" and
IC807
Replace
Yes
No
Check IC201 #12, #37
Replace
Yes
No
Check Q401, Q402
Replace
Yes
Check
IC201 #40, #41,
R416, R408, R409,
D401, D402
No
Replace
6. Standby Recording Defect, IC901S #5 Line: Check (D834, IC804, IC807, IC806)
6-8 No Color
1. Check the Color Adjustment level
2. Check IC301, #7
4. Check DY Connector
Yes
Insert a Cassette
Tape Recorded by
Another VCR and
Press Play Button
Yes
Play No See
Indication in (Regulator Inoperative)
Display
Yes
See
Mechanism No (Mechanism Does Not
Operation Operate in Play Mode)
See
No Video Missing in
PB-Video
Play Mode
Yes
Place VCR
Power On
Yes
(Load)
Tape Loading No ICM601-38 : HIGH No Moter B+ No
Operation ICM602- 2,10 Motor B+ Line
ICM601-39 : LOW
High
See
Cylinder No (Cylinder Does
Rotation Not Rotate)
Yes
See
Capstan No (Capstan Does
Rotation Not Rotate)
Yes
PTM601, PTM602,
S, T Reel DC
Supply/Take Up Reel Sensor
ICM601-99,98 PTM601, PTM602
Yes
Yes
Replace ICM601
Yes
Yes
No Rec SW Logic No
Tape Eject Change Tape Replace
ICM601
Yes
Replace SWM602
High
See
No (Video Missing in
REC-Video
Record Mode)
Yes
Mechanism See
(STOP) (Mechanism Does Not
State ICM601-63,
64,65 Operate In Play Mode)
(F.FWD)
See
Capstan Motor (STOP) (Capstan Does
Rotation Not Rotate)
(Rotate)
Check Mechanism
(Rotate)
Yes
Mechanism See
(STOP) (Mechanism Does Not
State ICM601-63,
64,65 Operate In Play Mode)
(Rew)
(Rotate)
Check Mechanism
Yes
Yes
Play Speed
Capstan Speed Check Mechanism Replace ICM601
Serach Speed
No Rec SW Logic No
Noise Bar Locking Change Tape Replace
ICM601
Yes Yes
Check
No (Control Pulse) No Check Start/End
Tape Loading
ICM601-76,77 Sensor ICM601
Yes Yes
No Check
Press Eject Button ICM601 - 37 LM B+ Line
Yes
No
ICM602-15:LOW No Replace
Check ICM601 ICM602-13:HIGH ICM602
Play
Yes
Yes
Check CTL No
Pulse AC Level (SP, LP
: Over 2Vp-p)
Yes
Replace
ICM601
9V No Check 12V
CNM603-5 at AL15V Line of
Power Supply
Yes
AL 5V No Check 6V at AL6V
CNM603-8 Line of Power Supply
Yes
Yes
No Check I-LIMIT.
CNM603-3 2.5V RM618
Yes
Yes
Check
Capstan Motor
Yes
Yes
Slower
(8 MHz) No Replace
XTM601 XTM601, CM609, CM610
Yes
Check
Cylinder Motor
Yes
Place VCR
Play Mode
Yes
Video FM In No No Check
Check ICM301-18
ICM301-17 Video Head
Yes
Video No Check
ICM301-20 QM302
Yes
Video No
ICM301-29 Check Video Out Line
Yes
Replace ICM301
Yes
Place VCR
Record Mode
Yes
FM-Video No
ICM301-21 Replace ICM301
Yes
FM-Video No
ICM301-18 Check RM313
Yes
Yes
Yes
Yes Check No No
XTM302 : 4.43MHz Change XTM302
Yes
Replace ICM301
Yes
Color No Check No
ICM301-61 XTM301 : 4.43MHz Replace XTM301
Yes
FM Signal No
ICM301-71 Check CM351
Yes
Replace ICM301
Yes
Check
ICM301 pin23,24 No Check VCR MICOM
(IC CLK DATA) (ICM601- pin27, 28)
Yes
Yes
Check ICM301 No
pin100 : PB audio signal Check CM301
(Small Signal)
Yes
Check ICM301 No
pin96 : PB Audio Replace ICM301
Signal
Yes
Check
ICM501 pin54 No
Check RM510, RM511, CM528
PB Audio signal
Yes
Check
ICM501 pin56,58 No
Check ICM501 & Hi-Fi Block
out put Audio
Yes
Check
TV NICAM PART(Sound Block)
Check No
ICM501 53pin Check ICM501 & Hi-Fi PART
MONO out
Yes No
Check TV part
Place VCR in REC Mode NICAM Block (ICM02)
Yes
Check No
ICM301 pin 75: Check PC 5V Line
5V
Yes
Check No
ICM301 pin7 REC Replace ICM301
audio signal
Yes
Yes
Yes
Replace CNM302
PB FM No CHECK
ICM501-18PIN ICM501-35PIN : A.HD SW
-20PIN : 5V
-24PIN : GND
RM501.RM502 & CYLINDER ASSY
Yes
HI-FI DET No
MONO MODE
ICM501-17PIN
Yes
CHECK
CHECK SIGNAL ICM501-31, 32PIN : CLOCK, DATA
ICM501-4,46PIN ICM601-27, 28PIN : CLOCK, DATA Yes
Yes
Yes
CHECK
REC - FM No ICM501- 31,32;CLOCK DATA Yes
ICM501-18PIN REPLACE ICM501
- 14,20,30,36,51;5V
- 60;9V
Yes
CHECK
INPUT SIGNAL No CHECK TV NICAM PART
ICM501-52, ICM02
61 PIN
Yes
Check
CYLINDER ASSY
MEMO
Œ ´
ˇ ¨ ˆ Ø
Œ GEAR FL CAM
´ MOTOR LOADING ASS’Y
ˇ LEVER FL ARM ASS’Y
¨ HOLDER FL CASSETTE ASS’Y
ˆ LEVER FL DOOR
Ø SLIDER FL DRIVE
Œ ´ ˇ ¨ ˆ
Ø ∏ ” ’” Ô ˝ Ò
Fig. 4-2 Top Parts Location-2
Œ ´ ˇ ¨ ˆ Ø ∏
” ’ ˝
Œ GEAR JOINT 1
´ GEAR JOINT 2
ˇ BRACKET GEAR
¨ MOTOR CAPSTAN ASS’Y
ˆ LEVER T LOAD ASS’Y
Ø GEAR LOADING DRIVE
∏ LEVER S LOAD ASS’Y
” HOLDER CLUTCH ASS’Y
’ BELT PULLEY
˝ SLIDER CAM
1) Push the Holder FL Cassette Ass'y Œ about 20mm 1) Pull the Holder FL Cassette Ass'y Œ to the eject
in the direction of arrow “A”. position.
2) Rotate the Lever FL Door ´ in the direction of 2) Pull the Holder FL Cassette Ass'y Œ as grasping
arrow “B”. the Holder FL Cassette Ass'y Œ and Lever FL
3) Release the Hook ˇ and Remove the Lever FL Cassette-R ´ in the same time to release hooking
Door ´ in the direction of arrow “C”. from Main Base until the Boss [A] of Holder FL
Cassette Ass'y Œ is taken out from the Rail [B].
3) Lift the Holder FL Cassette Ass'y Œ, in this time,
Œ HOLDER FL CASSETTE ASS'Y
you have to grasp the Lever FL Cassette-R ´
"A" Continuously until the Holder FL Cassette Ass'y
Œ is taken out completely.
ˇ HOOK
"C"
Œ HOLDER FL
"A" ´ LEVER FL CASSETTEE -R
CASSETTEE ASS`Y
BOSS [A]
4-2-3 Slider FL Drive, Gear FL Cam Removal 4-2-4 Lever FL Arm Ass’y Removal
1) Pull the Slider FL Drive Œ to the front direction. 1) Push the hole “A” in the direction of arrow “B”
use the pin.(about Dia. 2.5)
2) Remove the Slider FL Drive Œ in the direction of
arrow. (Refer to Fig. 1-6) 2) Pull out the Lever FL Arm Ass'y Œ from the Boss
of Main Base.
3) Remove the Gear FL cam ´.
3) Remove the Lever FL Arm Ass'y Œ in the direction
Note : When reinstalling be sure to reassemble Slider of arrow “C”.
FL drive Œ after you insert the Boss of Lever FL
ARM-R in Groove of Slider Fl drive Œ.
HOLE "A"
Assembly : Align the Gear FL Cam Œ with the Gear PIN
worm wheel Post as shown drawing.
(Refer to Timing point) "B"
"C"
´ GEAR FL CAM
Œ SLIDER FL DRIVE
Œ GEAR FL CAM
GEAR WORM WHEEL
POST
TIMING POINT
4-2-5 Gear Worm Wheel Removal 4-2-6 Motor Loading Ass’y Removal
Œ SCREW
4-2-7 Bracket Gear, Gear Joint 2, 1 Removal 4-2-8 Gear Loading Drive, Slider Cam,
Lever Load S, T Ass’y Removal
1) Remove the SCREW Œ.
2) Remove the Bracket Gear ´. 1) Remove the Belt Pulley. (Refer to Fig. 4-30)
3) Remove the Gear Joint 2 ˇ. 2) Remove the Gear Loading Drive Œ after releasing
4) Remove the Gear Joint 1 ¨. Hook [A] in the direction arrow as shown in detail
drawing.
Assembly : 3) Remove the Slider Cam ´.
1) Be sure to align dot mark of Gear Joint 1 Œ with 4) Remove the Lever Load ˇ, Link Load ˆ & Lever
dot mark of Gear Joint 2 ´ as shown Fig 4-12. Load ¨, Link Load Ø.
(Refer to Timing point1)
2) Confirm the Timing Point 2 of the Gear Joint 2 ´
and Slider Cam ˇ.
HOOK(A) Œ GEAR LOADING DRIVE
¨ GEAR JOINT 1
´ SLIDE CAM
ˇ GEAR JOINT 2 ¨ LEVER LOAD T
Œ SCREW
Ø LINK LOAD T
´ BRAKET GEAR ˇ LEVER LOAD S
ˆ LINK LOAD S
4-2-9 Gear Loading Drive, Slider Cam, 4-2-10 Lever Pinch Drive,
Lever Load S, T Ass’y Assembly Lever Tension Drive Removal
1) When reinstalling, be sure to align dot of Lever 1) Remove the Lever Pinch Drive Œ, Lever Tension
Load T Ass'y Œ with dot of Lever Load S Ass'y ´ Drive ´.
as shown in drawing, (Refer to Timing Point 1).
2) Insert the Pin A,B,C,D into the Slider Cam ˇ hole,
3) Be sure to align dot of Lever Load T Œ and dot of Œ LEVER PINCH DRIVE
TIMING POINT 1
TIMING POINT 3
STOPPER
"A"
MARK[B]
Œ LEVER S BRAKE ASS`Y HOOK(C)
HOOK(B)
´ LEVER T BRAKE ASS`Y
1) Push the Lever Idle Œ in the direction of arrow 1) Lift the Disk S, T Reel Œ, ´.
“A”, “B”.
2) Lift the Lever Idle Œ.
Œ DISK S REEL
Assembly :
1) Apply oil in two Bosses of Lever Idle Œ.
2) Assemble the Gear Idle ´ with the Lever Idle Œ.
"A"
Œ LEVER IDLE
´ GEAR IDLE
"B"
´ GEAR IDLE
HOOK "C"
4-2-15 Holder Clutch Ass’y Removal 4-2-16 Lever Up Down Ass’y, Gear Center
Ass’y Removal
1) Remove the Washer Slit Œ.
2) Lift the Holder Clutch Ass’y ´. 1) Remove the 2 hooks in the direction of arrow as
shown Fig. 4-21 and lift the Lever Up Down Ass’y Œ.
Note : When you reinstall Holder Clutch Ass'y 2) Lift the Gear Center Ass’y ´.
1) Check the condition of spring as shown in detail A.
2) Don't push Holder Clutch Ass'y down with exces- Assembly :
sive force Just insert Holder Clutch Ass'y into post 1) Insert the Lever Up Down Ass'y Œ in the rectan-
center with dead force and Rotate it smoothly. gular holes on Main Base as shown in Fig 4-22.
Be sure to confirm that spring is in the slit of Gear 2) Lift the Lever Up Down Ass'y Œ about 35°.
Center Ass'y as shown in detail B. (Refer to Fig 4-22)
3) Insert Ring of the Gear Center Ass'y ´ in the
Guide of the Lever Up Down Ass'y Œ.
Œ WASHER SLIT 4) Insert the Gear Center Ass'y ´ in the post on
Main Base.
´ HOLDER CLUTCH ASS`Y 5) Push down the Lever Up Down Ass'y Œ for
locking of the Hook.
Note :
1) Take care not to separate and sentence does not
mark sense.
2) Be sure to confirm that Ring of the Gear Center
Ass'y ´ is in the Guide of the Lever Up Down
Ass'y Œ after finishing assembly of Lever Up
Down Ass'y Œ and Gear Center Ass'y ´.
DETAIL A
DETAIL B
SPRING Fig. 4-21 Lever Up Down Ass’y Removal
4-2-17 Guide Cassette Door Removal 4-2-18 Lever Unit Pinch Ass’y, Plate Joint,
Spring Pinch Drive Removal
1) Lift the Hook [A].
2) Rotate the Guide Cassette Door Œ in the direction 1) Lift the Unit Pinch Ass’y Œ.
of arrow. 2) Remove the Plate Joint ´ from Lever Pinch Drive.
3) Remove the Spring Pinch Drive ˇ.
Note : After reinstalling the Guide Cassette Door Œ
sure the Hook [A]. Note :
1) Take extreme care not to touch the grease on the
Roller Pinch.
2) When reinstalling, be sure to apply grease on the
Œ GUIDE CASSETTE DOOR post pinch roller.
HOOK [A]
´ PLATE JOINT
Note :
1) Take extreme care not to get grease on the tape Œ FE HEAD
Guide Post.
2) After reinstalling, check the bottom side of the Post
#9 Guide to the top side of Main Base.
"A"
Œ SPRING #9 GUIDE
"B"
1) Pull out the FPC from connector of ACE Head 1) Move the Slider S, T Ass’y Œ, ´ to slot, and then
Ass’y ´. lift it to remove. (Refer to arrow)
2) Remove the screw Œ.
3) Lift the ACE Head Ass’y ´.
Œ SLIDER S ASS`Y
Œ SCREW
´ SLIDER T ASS`Y
4-2-23 Plate Ground Deck, Cylinder Ass’y Removal 4-2-24 Belt Pulley Removal
Note :
1) Take care not to touch the Cylinder Ass'y ˇ and
the tape guide post at reinstalling.
2) When reinstalling, Don't push down too much on
Screw Driver.
Œ 3 SCREWS
Fig. 4-30 Belt Pulley Removal
´ PLATE GROUND DECK
1-2-25 Level Head Cleaner Ass’y Removal
(Optional)
Œ HOOK
SLEEVE-HEAD CLEANER
ˇ CYLINDER ASS'Y
Fig. 4-29 Plate Ground Deck, Cylinder Ass’y Removal Fig. 4-31 Level Head Cleaner Ass’y Removal
4-2-26 Damper Capstan, Motor Capstan Ass’y 4-2-27 How to Eject the Cassette Tape
Removal (If the unit does not operate on condition that is
inserted into housing ass’y)
1) Remove the Damper Capstan Œ in the direction
of arrow. 1) Turn the Gear worm Œ clockwise with screw
2) Remove the 3 Screws ´. driver.(Refer to arrow)
3) Remove the Motor Capstan Ass’y ˇ. (Other method : Remove the Screw of Motor Load
Ass'y, Separate the Motor Load Ass'y)
Assembly :
1) Match the 3 holes of Motor Capstan Ass’y ˇ to the
3 holes of Main Base. Be careful not to drop or Œ GEAR WORM
knock the Motor Capstan Ass'y ˇ.
2) Tighten the 3 Screws ´ in the direction of arrow
as shown detail drawing.
3) Assemble the Damper Capstan Œ.
´ 3 SCREWS A B
Fig. 4-33
C
2) When Slider S,T are approched in the position of
unloading, rotate holder Clutch counterclockwise
Œ DAMPER CAPSTAN after inserting screw driver in the hole of frame's
bottom in order to wind the unwinded tape.
(Refer to Fig.4-34)
(If you rotate Gear Worm Œ continuously when
tape is in state of unwinding, you may cause a
tape contamination by grease and tape damage.
Be sure to wind the unwinded tape in the state of
set horizently.)
3) Rotate Gear Worm Œ clockwise using screw driver
again up to the state of eject mode and then pick
out the tape.(Refer to Fig.4-33)
ˇ MOTOR CAPSTAN ASS'Y
FRAME
Fig. 4-33
4-3 The table of clearing, Lubrication and replacement time about principal parts
1) The replacement time of parts is not life of parts.
2) The table 1-1 is that the VCR Set is in normal condition (normal temperature, normal humidity).
The checking period may be changed owing to the condition of use, runtime and environmental conditions.
3) Life of the Cylinder Ass’y is depend on the condition of use.
4) See exploded view for location of each parts.
<Table 1-1>
Checking Period
* Parts Name Remark
500 1000 1500 2000 2500 3000 3500 4000 4500 5000
POST TENSION ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ - To clean the parts, use patch and
SLANT POST S, T ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ alcohol (solvent).
T #8 GUIDE SHAFT ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆
- After cleaning, use the video tape
A CAPSTAN SHAFT ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ after alcohol is gone away com-
PE
#9 GUIDE POST ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ pletely.
P #3 GUIDE POST ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆
A GUIDE ROLLER S, T ∆ ∆ ∆ O O O O O O O - We recommend to use oil [EP-50]
T or solvent.
H CYLINDER ASS’Y ∆ O O O O O O O O O
FE HEAD ∆ ∆ ∆ O O O O O O O - One or two drops of oil should be
S ACE HEAD ∆ O O O O O O O O O applied after
Y cleaning with alcohol.
S PINCH ROLLER ∆ O O O O O O O O O
T POST REEL S, T - Periodic time of applying oil (Apply
E SLEEVE TENSION oil after cleaning)
M - The excessive applying oil may be
POST CENTER the cause of
LEVER IDLE BOSS (2Point) malfunction.
D CAPSTAN MOTOR PULLEY ∆ ∆ ∆ ∆ ∆ O O O O O
S
R BELT PULLEY O O O O O O O
Y
I HOLDER CLUTCH ASS’Y ∆ O O O O O O O O O
S
V
T GEAR CENTER ASS’Y O O O O O O O O O
I
E
N GEAR IDLE (2Point) O O O O O O O O O
M
G
LOADING MOTOR O O O O O O O O O
B S
R
A
Y
S
BAND BRAKE ASS’Y O O O O O O O O O
T
K E
E M BRAKE T ASS’Y O O O O O O O O O
Lower flange height of tape guide is used as the reference for the transport adjustment.
To maintain the height of the tape guide and prevent damage, do not apply excessive force onto the main base.
CYLINDER ASS'Y
#3 GUIDE POST
PINCH ROLLER
TENSION POST
TILT SCREW
X - POSITION #9 GUIDE POST
ADJUST SILT
AZIMUTH SCREW
CAPSTAN
#8 GUIDE POST
SCREW (A) SCREW (C) 1) Load alignment tape (Mono scope) and playback
TLIT ADJUST HEIGHT ADJUST the NTSC : 7KHz (PAL : 6KHz) signal.
2) Connect channel-1 scope probe to audio output
test point.
X-POSITION
3) Adjust screw (B) to achieve maximum audio level.
ADJUSTING SLIT (See Fig. 4-5-1)
SCREW (B) SCREW (D)
AZIMUTH ADJUST X-POSITION LOCKING 4-5-1(d) ACE HEAD POSITION (X-POINT)
ADJUSTMENT
Fig. 4-5-1 Location of ACE Head Adjustment Screw
1) See “2. Alignment and Adjustment” for ACE Head
position (X-Point) adjustment.
AUDIO HEAD
VIDEO HEAD
0 ~ 0 .25 mm
CONTROL HEAD
IDEAL ENVELOPE
S HEIGHT TOO HIGH S HEIGHT TOO LOW T HEIGHT TOO HIGH T HEIGHT TOO LOW
Fig. 4-5-7 Video Envelope Rising when Operation mode Changes Tape wrinkle at the guide roller S, T section :
from RPS to Play Mode
Linearity adjustment.
Tape wrinkle at tape guide flange :
ACE head assembly coarse adjustment.
5-1 Preadjustment
1. Do not attempt these adjustments in the Video Make the following adjustments after setting up
Mode. purity and convergence:
1. This mode uses the standard remote control. 4. Selection sequences for the
The Service Mode is activated by: (1) pressing PAL/SECAM B/G, L/systems:
the “FACTORY” service key on the local-key-
board, or (2) by entering the following remote- down or up key:
control sequence (within 2 seconds): AGC>TXP>AFW>SBT>SCT>SCR>STT>RG>
GG>BG>TCT>SC>SL>PVS>PHS>NVS>
STAND-BY →DISPLAY →MENU→ MUTE→ NHS>CDL>BKS
POWER ON
5. The VOLUME keys increase or decrease the
2. The “SERVICE (FACTORY)” message will be adjustment values, (stored in the
displayed. The Service Mode has three compo- non-volatile memory) when Adjustment Mode
nents: Adjustment, Option and Reset. is cancelled.
0 ~ 13 STEP 14" : 06
SUB CONTRAST SCT
20/21" : 10
SUB COLOR SCR 0 ~ 13 STEP 6
NOTE : PVS, PVA, PHS, NVS, NVA,NHS parameters must be aligned using
both the 50 Hz and 60 Hz vertical-field rates.
Even if the TV power is cut off, the Aging Mode is not cancelled.
The "AGING" marking is displayed on the screen.
The AGING mode is cancelled by repressing the "FACTORY" key.
5-2-4 Option
N T
MODEL CODE T SYS TU VPS AUTO OSD
O X AUDIO TEM ATS NER G-CODE PDC CLOCK S-MODE SPEED LAN LANG
1 TF14C53X/XEF CF 1 OFF EU FRA
2 TF14C3D3X/XEF CF 2 OFF EU FRA
3 TF14B5F3X/XEF O MONO CF ON 1 S/VIEW PDC OFF OFF EU FRA
4 TF20C3DDF3X/XEF O MONO CF ON 2 S/VIEW PDC OFF OFF EU FRA
5 TF21B3N3X/XEF O NICAM CF ON 2 S/VIEW PDC OFF 54% ON EU FRA
6 TI14C5F3X/XEU O MONO CI ON 1 V/PLUS PDC OFF ON EU ENG
7 TI14B53X/XEU CI 1 ON EU ENG
8 TI21B5DF3X/XEU O MONO CI ON 2 V/PLUS PDC OFF ON EU ENG
9 TI21B3N3X/XEU O NICAM CI ON 2 V/PLUS PDC OFF 80% ON EU ENG
10 TX14C5F3X/XEG O MONO CX ON 1 S/VIEW VPS OFF OFF EU DEU
11 TX20C5DF3X/CEG O MONO CX ON 2 S/VIEW VPS OFF OFF EU DEU
12 TX21B3N3X/XEG O NICAM CX ON 2 S/VIEW VPS OFF 80% ON EU DEU
13 TX50C5DF3X/XET O MONO CX ON 2 S/VIEW PDC OFF OFF EU ITA
14 TX21B5DF3X/XET O MONO CX ON 2 S/VIEW PDC OFF OFF EU ITA
15 TX21B3N3X/XET O NICAM CX ON 2 S/VIEW PDC OFF 80% ON EU ITA
16 TX14C53X/XEP CX 1 OFF EU ENG
17 TX21B3N3X/XEP O NICAM CX ON 2 S/VIEW PDC OFF 80% ON EU ENG
18 TF21B5DF3X/AUT O MONO CX ON 2 S/VIEW VPS OFF OFF EU GER
19 TF21B3N3X/AUT O NICAM CX ON 2 S/VIEW VPS OFF 80% ON EU GER
20 TX14C5D3X/XEC CX 2 OFF EU ESP
21 TX20C5F3X/XEC MONO
O CX ON 1 S/VIEW PDC OFF OFF EU ESP
22 TX21B5DF3X/XEC MONO
O CX ON 2 S/VIEW PDC OFF OFF EU ESP
23 TX21B3N3X/XEC NICAM
O CX ON 2 S/VIEW PDC OFF 80% ON EU ESP
24 TX14C53X/EDI CX 1 OFF EU ENG
25 TX20C5D3X/EDI O
MONO CX ON 2 S/VIEW PDC OFF OFF EU ENG
26 TX21B3N3X/EDI O
NICAM CX ON 2 S/VIEW PDC OFF 80% ON EU ENG
27 TX14C53X/NSI CX 1 OFF EU ENG
28 TX14B5F3X/NSI MONO
O CX ON 1 S/VIEW PDC OFF OFF EU ENG
29 TX21B5DF2X/NSI MONO
O CX ON 2 S/VIEW PDC OFF OFF EU ENG
30 TX21B3N3X/NSI NICAM
O CX ON 2 S/VIEW PDC OFF 80% ON EU ENG
31 TX14C53X/XEE CX 1 OFF EU SWE
32 TX14C5F3X/XEE MONO
O CX ON 1 S/VIEW PDC OFF OFF EU SWE
33 TX21B5DF3X/XEE MONO
O CX ON 2 S/VIEW PDC OFF OFF EU SWE
34 TX21B3N3X/XEE NICAM
O CX ON 2 S/VIEW PDC OFF 80% ON EU SWE
35 TX14B5F3X/ELS O
MONO CX ON 1 S/VIEW VPS OFF OFF EU DEU
36 TX20C5DF3X/ELS O
MONO CX ON 2 S/VIEW VPS OFF OFF EU DEU
37 TX21B3N3X/ELS O
NICAM CX ON 2 S/VIEW VPS OFF 80% ON EU DEU
38 TX14C53X/EUE CX 1 OFF EU ENG
39 TX20C5D3X/EUE CX 2 OFF EU ENG
40 TW21B3N3X/BWT O
NICAM CW OFF 2 S/VIEW NONE OFF 100% ON RUS RUS
41 TW14C33X/BWT CW OFF 1 - - OFF OFF RUS RUS
42 TW20C5D3X/BWT CW OFF 2 RUS RUS
43 TW21B5DX/BWT CW OFF 2 RUS RUS
44 TF15X53X/XEF CF OFF 1 EU FRA
45 TW15X53X/BWT CW OFF 1 RUS RUS
5-3 Reset
1. Volume 10
2. Program Channel 1
3. P-STD CUSTOM
4. Auto Power OFF
5. NR OFF
6. Reserved Timer Recording ALL CLEAR
7. Skip (Store/Clear) ALL CLEAR
Caution : When the EEPROM is replaced, all items revert to their initial values.
1. Usually, a color TV needs only slight A degaussing coil is mounted around the
touch-up adjustment upon installation. picture tube, so that external degaussing after
Check the basic characteristics such as height, moving the TV should be unnecessary. But
horizontal and vertical sync and focus. the receiver must be properly degaussed upon
installation.
2. The picture should have good black and white
details. There should be no objectionable The degaussing coil operates for about 1
color shading; if color shading is present, second after the power is switched ON. If the
perform the purity and convergence adjust- set has been moved or turned in a different
ments described below. direction, disconnect its AC power for at least
10 minutes.
3. Use the specified test equipment or its
equivalent. If the chassis or parts of the cabinet become
magnetized, poor color purity will result. If
4. Correct impedance matching is essential. this happens, use an external degaussing coil.
Slowly move the degaussing coil around the
5. Avoid overload. Excessive signal from a sweep faceplate of the picture tube and the sides and
generator might overload the front-end of the front of the receiver. Slowly withdraw the coil
TV. When inserting signal markers, do not to a distance of about 6 feet before removing
allow the marker generator to distort test power.
results.
3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.
2. Adjust the VR screen for a normal picture is (no blooming or flyback line).
3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.
2. Plug in the CRT deflection yoke and tighten the clamp screw.
3. Plug the convergence yoke into the CRT and set in as shown in Fig. 5-1.
7. Loosen the clamp screw holding the yoke. Slide the yoke backward or forward to provide
vertical green belt. (Fig. 5-2).
9. Slowly move the deflection yoke forward, and adjust for the best overall green screen.
11. Produce blue and red rasters by adjusting the low-light controls. Check for good purity
in each field.
Clamper
Screw ADJUST
(VERTIC
YOKE
CLAMP
SCREW
6 POLE
CONVERGENCE
4 POLE
CONVERGENCE
31m/m
5-4-8 Center Convergence Adjustment 5. Turn the both tabs at the same time, keeping
the angle constant, and superimpose the red
1. Warm up the receiver for at least 20 minutes. and blue horizontal line in the center of the
screen.
2. Adjust the two tabs of the 4 pole magnets to
change the angle between them. Superimpose 6. Adjust the two-tab pairs of the 6-pole magnets
the red and blue vertical lines in the center to superimpose the red and blue line onto the
area of the screen. green. (Changing the angle affects the vertical
lines, and rotating both magnets affects the
3. Adjust the Brightness and Contrast controls for horizontal lines.)
a well defined picture.
7. Repeat adjustments 2~6, if necessary.
4. Adjust the two-tab pairs of the 4 pole magnets,
and change the angle between them. 8. Since the 4-pole magnets and 6-pole magnets
Superimpose the red and the blue vertical interact, the dot movement is complex
lines in the center area of the screen. (Fig. 5-3).
BLUE RED/BLUE
RED GREEN
Test Equipment
1. TV Generator (PM5518,PM5418,ETC.)
2. DC VOLTMETER
5-5-1 Preparation
Burst Signal
0.7V (as fiat as possible)
0.3V
0.3V
Fig. 5-6 Color bar signal of alignment tape (75% Color Bars)
5-5-3 PROGRAM SW
SW
POSITION I a II b III c IV d V e VI f VII
SW A
SW B
SW C
ON OFF
S/SEN
OFF
ON
E/SEN
POWER
OFF
LOAD
STANDBY REV PLAY SPT1 SPT2 F/R1 F/R2
END
LOAD
START
STANBY 0 0 0 0 0 Eject
X : DON’T CARE
65 RM502 2001-000577 R 2K O X HI FI
66 RM503 2001-000995 R 820 O X HI FI
67 RM504 2001-000472 R 2.7K O X HI FI
68 RM505 2001-000508 R 220K O X HI FI