Beruflich Dokumente
Kultur Dokumente
milkburp
The timing of the blinking you see would be as follows: two to nine blinks, (depending on the fault), about
a third of a second apart, then a pause for 3 seconds, then the two to nine blinks about a third of a
second apart again.
Here is a list of the problems that might have occurred indicated by the number of blinks. The words in
parentheses are those, which you will see for each of these faults on a diagnosis screen described later in
this article.
• Unit is dead, No blinks - Problem in the standby power section. Might check fuse, R607, Q601, IC601,
R612 and VDR601 (should show open).
• Continuous blink once a second, no pausing - No reply from the jungle IC301 (data bus is busy, shorted
to ground, or held high), IK video path is defective.
• One blink - not used for the self-diagnosis
• Two blinks - B+ over current protection (OCP), unit goes to the standby mode then displays the 2 blink
fault. Could be a short in the power supply of any of the circuits.
• Three blinks - B+ over voltage protection (OVP), unit goes to the standby mode then displays the 3 blink
fault. This is also a problem in the power supply circuit, check T603 and R672.
• Four blinks - No vertical Deflection (V STOP), Screen goes to a single horizontal line then the video signal
muted. Check IC1509, Q1505
• Five blinks - AKB circuit (automatic kine bias), the timer/standby indicator blinks for about 30 seconds then
goes to the self-diagnosis function. Something is wrong with the video. Check video out, Q705, 732, 761 and
other components on the C board, also check Q218, 219, 220 on the A board. In addition, unit could be in IK
blanking, try turning up screen slightly.
• Six blinks - No Horizontal (H STOP), no raster, goes to the blinking self-diagnosis function immediately.
Check C515 & 516 and the jungle IC, IC206.
• Seven blinks - High voltage shutdown. The high voltage has exceeded 33k and the unit goes immediately
into safety shutdown. Check power supply regulation and horizontal circuits.
• Eight blinks - Problem with the audio (AUDIO), unit goes to standby and blinks the self-diagnosis code.
Check IC406 audio amp, PS401, and 402. On some projection models of Sony TV sets, this code means that
T8005 (flyback transformer), or the associative components in the high voltage circuits are defective on the D
board.
• Nine blinks - Replace D 6116 and D 6301 on the "G" board, do not resolder as this will fix the problem
temporary. Or Panel Module Error or Thermal Error. If it is intermittent 9 blinks, meaning sometimes the TV
comes on and other times you get flashing, then change the switching regulator on the "G" board or check
connections. Make sure the regulator is -12 or -13 (negitive).
• Ten blinks - Check Q8014 and Q8013 for shorts, leakage, or bad solder connections on the " D" board. If
the transistors are bad, check R8051 and IC8005, also on the "D" board.
Intermittent problems? This is a great feature. You can also bring up these fault codes on-screen to see a
list of the problem numbers with the abbreviation of the problem and the number of times this problem
has occurred. This is slightly different than entering the service mode. To see the diagnostic screen, press
the following buttons: Display, Channel, 5, volume Minus, ( not plus ) then Power. This brings up a screen
with a list of the problems and number of times they have occurred. Each of the problems named, are
abbreviated as, "OCP", "OVP", "V STOP", ETC. We have repeated them in parentheses in the text for the
"Blinks" described above so you can correlate between the diagnostic screen and the blink codes.
Now that you know about these self-diagnostics, how do you use them? Say that you have a set with a
black screen. You see that the LED is blinking four times. This would tell you that you have no vertical
sweep, which is why the video is muted. If it was blinking 6 times, you would know that you have a
horizontal fault. It's not a sure cure..
IMPORTANT: After you repair the unit, you MUST clear the values on this diagnostic
screen. These codes do not reset themselves after the fault is corrected, so if you don't clear
them, you'll be seeing "old" fault codes the next time you enter this screen. Clearing is done
by going into the service mode (display, channel, 5, volume plus, then power ). Press 8 and
Enter, which returns everything to the factory preset condition.
Related Articles
• How To Connect a Computer To Your TV
• How to Clean Your TV, Computer, or Laptop Screen
Echo 31 Items
Admin
Log In
Edit My Profile
Follow
Moderation
General Settings
Admin Notices
Log In
Echo Blog
Echo on Twitter
Help
RAJA
THANKS ABOUT THIS IN FO
BUT WHAT HAPAN IF A SONY TV BLINKING 16 TIM AND 3 SEC AFTER AGAN?
dennis beaudry
yours is the first site that relly gave me a direct answer. thank you very much
Anonymous
where can i purchase parts for my sony part d6116 and d6301
Friday, February 13, 2009, 4:08:43 AM
Guest
My goodness. I have been searching far and wide for the answer to this question thank you so much.
Liked by
Guest
AlfaExpress
Hi I have a sony KDF-50E2010, it blinks 8 times(green) then 3 seconds then 8 Green then 3 sec, 8 green, then
turns the lamp light(red) not blinking with thr other led tuens red and blinks 3 time? Any ideas or should I buy a
new one!
Liked by
Guest
Guest
thank you this solved what the problem is.
not sure how to fix the problem.
Matt
I have a Sony 57" WEGA CRT HDTV Model KDP57WS655. It displayed 9-blinking lights on the standby button and
would only turn on intermittently - sometimes it would turn on and others not when pressing the power button.
I followed the instructions to enter the diagnostic screen and the tv came on and displayed that it had (only) errors
(105) ZCD.
What is the problem and can I order parts and repair it mysself?
VR/Matt
Guest
having same problem........how did you fix it
Blink6
We have a Sony KDP-57XBR2. No picture, no sound. Standby light blink 6 times.
I see the article above but what do we do to fix it?
Liked by
Guest
nate
Where is the G board located on the Sony KV-36FS120?
Liked by
Guest
2 Guests
john
i have a kp41t65 and the led on front just blinks constant i replaced the power board and tuner board and tv still
dont work led still blinking constant with black screen i hear the relay clicking when i turn it on but nothing i see
theres a type of reset here on this site but i dont have the remote where do i go from here?
Liked by
Guest
Clint
I've got a KV-40xbr800 that flashes 7 times. I read that it's the mcz3001d and I've read that it's the electrolytic
caps. Which is it? If I unplug the tv for a day or so, it will turn back on.
Chad
I have a KDF-50WE655. The tv turns on for about a minute then the bulb turns off and on over and
over. The tv never actualy turns off and the bulb don't seem to be bad, since i do get some picture for
seconds at a time...........Can anyone help?
Liked by
Guest
Guest
Hey, what if you don't have a "channel" button?
• < Prev
• 1
• 2
• 3
• Next >
•
---------------------------------------------------------------------------------------------------------------------
----------------------
arinc429@haotmail.com
-------------------------------------------------------------------------------------------------------------------
Rags said: My tv is Red 10 blinking, with audio but no picture. On the random occasion i might
get the screen working, with the 10 red blinks still on. i must confess i have pulled the board out
from behind, and i know noting. Its a Sony KP-FX423M91. i have also pulled a wire out and put
it back in, and it started a couple times. Random wires, now i dont though. Scared incase it blows
or something. Can you help a person in distress??
PLS GET SOME HELP FROM SOME ONE WHO CAN AT LEAST SOLDER AN IC.IF
YOUR TV IS STILL ON 10 BLINKS AND SOME TIME U HAVE VIDEO ALSO
ESPECIALLY U KEEP THE TV OFF FOR MORE THAN 10 HOURS.REPLACE THE IC
8002, IC Part No. MCZ3001DB in D BOARD. IN YOUR TV D BOARD IS ON YOUR LEFT
WHILE LOOKING FWD FROM BACK OF TV.BUT DO CARE ABOUT RED, HV THICK
WIRE. DONOT REMOVE IT FROM BOARD SIDE, U CAN REMOVE F RED WIRE FROM
D BOARD SIDE. I REPEAT GET SOME HELP AND ASK HIM TO REPLACE ABOVE
MENTIONED IC. ITS PRICE IS 11 US DOLLARS.BY THE WAY WHAT IS YR LOCATION
,
ARINC429
Rags said: My tv is Red 10 blinking, with audio but no picture. On the random occasion i might
get the screen working, with the 10 red blinks still on. i must confess i have pulled the board out
from behind, and i know noting. Its a Sony KP-FX423M91. i have also pulled a wire out and put
it back in, and it started a couple times. Random wires, now i dont though. Scared incase it blows
or something. Can you help a person in distress??
Hi Rags,
have a Sony Triniton SRS BBE and is doing the self diag with 9 blinks. Your Page
says Replace D 6116 abd D 8301 on the G Board. How much will this part be cost?
In addition I did the Display, Channel(usedup botton),5, volumne Minus, power but
the diag screen did not come on do you have any suggestions?
------------------------------------------------------------------------------------------------------
------------------------------------have a sony kp-46wt510 with eight blinking lights...i
guess i am suppose to
Eight blinks - Problem with the audio (AUDIO), unit goes to standby and blinks the
self-diagnosis code. Check IC406 audio amp, PS401, and 402. On some projection
models of Sony TV sets, this code means that T8005 (flyback transformer), or the
associative components in the high voltage circuits are defective on the D board.
does anyone have any idea how i do this?
I have another Sony Trinitron TV Model number KV-21R1D.If I press the power button ,the Red
light turns on for about 8 seconds, after that it off and , starts to blink for 6 times,.I have checked
the C515 and C516 and the jungle IC, IC206 on the board but I could not find them on the
electronic circuit board of the TV.Kindly tell me what to do about this ,or where exactly these
components are on the electronic circuit of this model of my TV,KV-21R1D.Or what exactly
should I do.
hockeydad said: I have a service manual for my kv-36xbr800. The set blinks three times and
then goes to stand by. A blog I looked at said IC6505 is bad. On the Tech lore it also gave T603
and r672. Neither of these references show up in the component listing. Any one have any idea
which these refer to?
I think my service manual download finally worked today. This is the issue I am trying to
resolve. THe part numbers given here do not match the manual. The IC 6505 does.
Oranom said:
Rags said: My tv is Red 10 blinking, with audio but no picture. On the random
occasion i might get the screen working, with the 10 red blinks still on. i must
confess i have pulled the board out from behind, and i know noting. Its a Sony KP-
FX423M91. i have also pulled a wire out and put it back in, and it started a couple
times. Random wires, now i dont though. Scared incase it blows or something. Can
you help a person in distress??
Hi Rags, I had same problem my TV. Replaced IC8002 on the 'D' board. This is what
we did: 1.Bought 2 x MCZ3001D from WES components in Ashfield Sydney Australia
for $11.20 (each). 2.Friend had an 18 pin machine spun socket (not the crappy ones
on EBAY). 3.Took back off TV 4.Put the 'D' board in service position 5.Noted which
way IC8002 chip sat (Where position 1 is), also noted which 2 legs are not soldered.
6.Cut the black plastic that was covering this chip underneath (where D board
screws into) as this is easier than removing the 'D' board. 7.De-soldered the IC8002
chip with a proper de-soldering iron. These are expensive though. 8.Soldered in the
18 pin socket. 9. Set the chip into the socket. 10.Tested TV, worked fine. 11. Put it
all back together, plugged in Tivo, DVD etc etc etc and all bloody good stuff. 12. I
now also have a spare MCZ3001D which is taped to the back of the TV for future
replacement, which is now easier since its now in a socket.
Hey Oranom,
Thanks for the advise and great instructions. it looks complex, therefore i will have to hire pro help. Someone
came, took a look and said the transformer, which would cost £250GBP. i can get a new samsung for £500, 40". all
this 18 pin socket is confussing. got any pics. How much do you think a pro should charge?? and how long a job??
thanking u in advance
arinc429
Member
• member since: 11/19/2008
• rank: 16966 of 39894
• 13 comments
arinc429 said:
Rags said: My tv is Red 10 blinking, with audio but no picture. On the random
occasion i might get the screen working, with the 10 red blinks still on. i must
confess i have pulled the board out from behind, and i know noting. Its a Sony KP-
FX423M91. i have also pulled a wire out and put it back in, and it started a couple
times. Random wires, now i dont though. Scared incase it blows or something. Can
you help a person in distress??
PLS GET SOME HELP FROM SOME ONE WHO CAN AT LEAST SOLDER AN IC.IF YOUR
TV IS STILL ON 10 BLINKS AND SOME TIME U HAVE VIDEO ALSO ESPECIALLY U KEEP
THE TV OFF FOR MORE THAN 10 HOURS.REPLACE THE IC 8002, IC Part No.
MCZ3001DB in D BOARD. IN YOUR TV D BOARD IS ON YOUR LEFT WHILE LOOKING
FWD FROM BACK OF TV.BUT DO CARE ABOUT RED, HV THICK WIRE. DONOT
REMOVE IT FROM BOARD SIDE, U CAN REMOVE F RED WIRE FROM D BOARD SIDE. I
REPEAT GET SOME HELP AND ASK HIM TO REPLACE ABOVE MENTIONED IC. ITS
PRICE IS 11 US DOLLARS.BY THE WAY WHAT IS YR LOCATION , ARINC429
Thanks for your advise. Im based in london. Do you anywhere i can get pics from
of the board parts ect??
I am in Dubai, I asked the location because I have one spare IC. It is my firm belive this IC is also bad in your case,
even any Sony dealership/service centre knows about that as it is known issue to them. pls get this IC and ask some
electrician to soler it. Photo will not help much for location.Once u remove the D board,which is on yr left looking
from back of TV.
arinc429@hotmail.com
JLP
Member
Thanks,