Beruflich Dokumente
Kultur Dokumente
6 Poles and 8 Poles TEFC, DP, Flame-proof Cast Aluminium and Cast Iron Frames for
(Type 'd'), Increased Safety (Type 'e'), sturdy construction.
(Type 'p'), Squirrel Cage Rotor and Slip-ring Special designs for Crane Duty, Machine Tool
Motors, in cast aluminium or cast iron Duty, Textile Duty, Rolling Mill Duty etc.
2
INDEX
1 Next Page
1
PRINCIPLES OF
INDUCTION MOTOR
MOVEMENT LOAD
CURRENT INDUCED
FLOW EQUIVALENT
MAGNET
N
N A current flowing in a
conductor produces a
magnetic field
S S
The direction of
If a magnetic field is cut by a moving current flow
S conductor, an EMF (voltage) is induced in the N determines the
conductor. When external circuit is completed polarity of the
a current flows through the conductor. induced magnetic
field.
MAGNETS
N S N MOVEMENT
CONDUCTOR
FORCE OR PULL
MOVEMENT
S N S
MAGNETS
The magnetic field as it moves to the right, relative to the conductor, induces a current in the conductor. This induced
current produces an induced magnetic field which opposes this relative movement (Lenz's Law). As long as the relative
movement continues a force is produced which will tend to move the conductor to the right (i.e. tending to lift the load).
TIME 1 2 3 4 5 6 7 TIME 1
A
N TIME 2 A S TIME 3 A S TIME 4
A
PHASE A
CURRENT
N C B C B C
C B
N
S
N
S
S
N
N
S
PHASE B
CURRENT
At time 1 the upper At time 2, poles At time 3, poles (A)
Alternating current can be used pole (A) is at a (A) and (B) have and (C) have S
to produce a moving magnetic maximum N N polarity. (A) is polarity. Pole (B)
polarity. The lower decreasing and has increased to
field. 3 phase a.c. applied to field
poles have S (B) is increasing. maximum N
coils as shown, produces a polarity: (B) is Pole (C) now has polarity.The pattern
rotating magnetic field. decreasing and (C) maximum S continues to Time 7
is increasing (S polarity. then begins the
polarity). cycle again.
2 2
PRINCIPLES OF
INDUCTION MOTOR
ROTATING MAGNETIC
C TIONOF FIEL
DIRE D
ROTOR WITH
CONDUCTORS N S
STATOR
FIELD
COILS
S N
3 3
TEFC
SQUIRREL CAGE
MOTORS
4 4
TEFC
SQUIRREL CAGE
MOTORS
PERFORMANCE DATA
Supply : 415 V or 380V, 50 Hz, 3 Phase AC Voltage Variation : ± 10%
Enclosure : Totally Enclosed Fan Cooled (TEFC) Frequency Variation : ± 5%
Degree of Protection : IP55 Combined Variation : ± 10%
Rating: Continuous, Duty : S1 Ambient : 45°C
Insulation Class : ‘F’ Temperature Rise by Resistance Method : 75°C Max.
P
OUTPUT FL FL EFFICIENCY (%) POWER FACTOR DOL STG. S/D STG. NETT
O FL GD²
FRAME AMPS AMPS WEIGHT
L RPM 3/4 1/2 3/4 1/2 STG. C STG. T STG. C STG. T KgM²
kW HP 380 V 415 V FL FL Kg.
E FL FL FL FL %FLC %FLT % FLC % FLT
0.18 0.25 2 AD63 2700 0.55 0.50 64.0 60.0 48.0 0.79 0.72 0.64 500 275 0.001 5.6
0.18 0.25 4 AD63 1330 0.85 0.75 50.0 46.0 40.0 0.65 0.58 0.47 400 200 0.003 5.6
0.25 0.33 2 AD63 2700 0.75 0.75 64.0 60.0 48.0 0.79 0.72 0.64 500 275 0.001 5.6
0.25 0.33 4 AD71 1350 1.10 0.90 58.0 53.0 48.0 0.60 0.55 0.49 500 200 0.004 7.0
0.37 0.50 2 AD71 2800 1.1 1.0 65.0 60.0 48.0 0.79 0.72 0.64 500 275 0.002 7.0
0.37 0.50 4 AD71 1350 1.4 1.2 65.0 58.0 45.0 0.64 0.58 0.48 500 200 0.004 7.0
0.37 0.50 6 AD80 910 1.3 1.1 64.0 58.0 50.0 0.69 0.60 0.50 400 200 0.011 10
0.37 0.50 8 AD90S 680 1.6 1.5 60.0 54.0 48.0 0.57 0.50 0.40 400 170 0.016 22
0.55 0.75 2 AD71 2800 1.6 1.5 68.0 64.0 57.0 0.79 0.72 0.61 600 300 0.003 10
0.55 0.75 4 AD80 1395 1.7 1.5 72.0 67.0 59.0 0.70 0.64 0.58 500 200 0.007 10
0.55 0.75 6 AD80 910 1.8 1.7 65.0 60.0 52.0 0.71 0.63 0.52 400 200 0.011 10
0.55 0.75 8 AD90L 680 2.1 1.9 62.0 56.0 46.0 0.63 0.54 0.45 400 170 0.021 25
0.75 1.0 2 AD80 2820 1.9 2.0 75.0 69.0 62.0 0.81 0.73 0.62 600 300 0.003 10
0.75 1.0 4 AD80 1400 2.2 2.1 74.0 69.0 61.0 0.70 0.65 0.60 500 200 0.007 10
0.75 1.0 6 AD90S 925 2.4 2.2 69.0 66.0 60.0 0.70 0.63 0.55 500 200 0.015 13
0.75 1.0 8 AD100L 690 2.8 2.8 65.0 56.0 46.0 0.63 0.54 0.45 400 175 0.030 19
1.10 1.5 2 AD80 *** 2820 2.8 2.5 75.0 72.0 64.0 0.81 0.76 0.68 600 275 0.006 10
1.10 1.5 2 AD90S 2830 2.6 2.3 77.0 72.0 64.0 0.82 0.76 0.68 600 275 0.006 13
1.10 1.5 4 AD90S 1410 2.8 2.7 77.0 71.0 63.0 0.77 0.70 0.62 500 200 0.014 13
1.10 1.5 6 AD90L 925 3.4 3.2 70.0 67.0 62.0 0.71 0.65 0.55 500 200 0.021 16
1.10 1.5 8 ND100LX 690 3.5 3.6 71.0 66.0 58.0 0.68 0.57 0.44 400 175 0.034 35
1.50 2.0 2 AD90S 2830 3.6 3.2 78.0 73.0 64.0 0.82 0.76 0.68 600 275 0.006 13
1.50 2.0 4 AD90L 1405 3.7 3.4 77.0 72.0 65.0 0.79 0.72 0.62 500 200 0.019 16
1.50 2.0 6 AD100L 925 4.1 4.0 75.0 71.0 64.0 0.75 0.68 0.58 500 200 0.030 19
1.50 2.0 8 ND112MX 700 4.7 4.3 72.0 67.0 60.0 0.68 0.58 0.46 400 190 0.057 45
2.20 3.0 2 AD90L 2830 5.2 4.8 79.0 73.0 66.0 0.82 0.77 0.70 600 275 0.008 16
2.20 3.0 4 AD100L 1425 5.1 4.8 80.0 75.0 69.0 0.82 0.76 0.68 600 200 0.030 19
2.20 3.0 6 ND112M 920 5.8 5.5 77.0 74.0 67.0 0.75 0.70 0.60 500 200 0.048 42
2.20 3.0 8 ND132S 710 6.0 5.7 76.0 71.0 64.0 0.73 0.68 0.61 450 180 0.174 68
3.0 4.0 2 AD100L 2865 6.5 7.3 82.0 79.0 73.0 0.85 0.80 0.72 700 250 0.022 19
3.0 4.0 4 ND100LX*** 1425 6.9 6.3 81.0 80.0 78.0 0.82 0.76 0.68 600 200 0.034 35
3.0 4.0 6 ND132S 940 7.0 6.5 82.0 79.0 74.0 0.79 0.75 0.68 500 200 0.174 68
3.0 4.0 8 ND132M 700 8.3 7.6 78.0 73.0 66.0 0.70 0.66 0.60 500 170 0.214 79
4.0 5.5 2 ND112M 2865 8.5 7.5 81.0 79.0 76.0 0.88 0.84 0.75 650 250 165 62 0.030 42
4.0 5.5 4 ND112MX*** 1430 9.0 8.5 82.0 81.0 78.0 0.81 0.76 0.69 600 200 150 50 0.052 45
4.0 5.5 6 ND132M 945 9.3 8.5 83.0 81.0 77.0 0.79 0.75 0.68 550 200 140 50 0.214 79
4.0 5.5 8 ND160M 710 10.0 9.0 85.0 85.0 83.0 0.74 0.70 0.62 500 200 140 60 0.460 121
5.5 7.5 2 ND132S 2865 11.5 10.5 84.0 82.0 79.0 0.89 0.84 0.76 700 250 175 62 0.062 68
5.5 7.5 2 ND112MX*** 2860 12.0 11.0 83.0 81.0 78.0 0.87 0.83 0.76 650 250 165 62 0.034 45
5.5 7.5 4 ND132S 1440 12.0 11.0 85.0 83.0 80.0 0.84 0.79 0.73 600 200 150 50 0.131 68
5.5 7.5 6 ND132M**** 945 13.1 12.0 83.0 81.0 77.0 0.80 0.75 0.68 550 200 140 50 0.214 79
5.5 7.5 8 ND160M 710 13.0 12.0 85.0 85.0 83.0 0.74 0.70 0.62 500 200 140 60 0.460 121
7.5 10.0 2 ND132S 2865 15.2 14.0 85.0 84.0 82.0 0.89 0.85 0.76 650 275 165 68 0.062 68
7.5 10.0 4 ND132M 1440 15.8 14.5 86.0 85.0 84.0 0.85 0.81 0.75 600 200 150 50 0.161 79
7.5 10.0 6 ND160M 970 16.0 15..0 87.0 87.0 86.0 0.80 0.76 0.68 550 225 155 65 0.460 121
7.5 10.0 8 ND160L 710 18.0 16..0 85.0 85.0 83.0 0.76 0.72 0.64 500 200 140 60 0.640 143
9.3 12.5 2 ND132M*** 2880 18.5 17.0 86.0 85.0 84.0 0.89 0.85 0.78 700 240 180 60 0.076 79
9.3 12.5 2 ND160M 2920 18.0 16.5 87.0 87.0 85.0 0.88 0.86 0.78 650 250 185 75 0.13 121
9.3 12.5 4 ND160M 1460 19.0 17.5 88.0 88.0 86.0 0.85 0.81 0.73 600 225 170 65 0.31 121
9.3 12.5 6 ND160L 970 20.0 18..5 88.0 88.0 85.0 0.80 0.76 0.68 550 225 155 65 0.59 143
9.3 12.5 8 ND180M 710 22.0 20..0 86.0 86.0 84.0 0.76 0.72 0.64 500 200 140 60 0.99 182
5 5
TEFC
SQUIRREL CAGE
MOTORS
6 6
TEFC
SQUIRREL CAGE
MOTORS
7 7
TEFC
SQUIRREL CAGE
MOTORS
SHIPPING SPECIFICATIONS
FOOT MOUNTED MOTORS
NETT WEIGHT GROSS WEIGHT DIMENSIONS VOLUME
FRAME KG KG L IN MM B IN MM H IN MM CUBIC METRES
Wooden Carton Wooden Carton Wooden Carton Wooden Carton Wooden Carton Wooden Carton
AD63 5.6 7.5 235 155 205 0.0075
AD71 7.0 9.0 275 175 220 0.0106
AD80 10.0 13.0 325 210 240 0.0164
AD90S 13.0 17.0 375 220 290 0.0239
AD90L 16.0 20.0 375 220 290 0.0239
AD100L 19.0 24.0 400 245 305 0.0299
ND100LX 35.0 40.0 425 305 275 0.0356
ND112M 42.0 42.0 59.0 48.0 525 480 410 360 355 325 0.0764 0.0562
ND112MX 45.0 45.0 62.0 51.0 525 480 410 360 355 325 0.0764 0.0562
ND132S 68.0 68.0 92.0 76.0 625 550 445 400 410 380 0.1140 0.0836
ND132M 79.0 79.0 103.0 88.0 625 550 445 400 410 380 0.1140 0.0836
ND160M 121 179 750 585 545 0.239
ND160L 143 209 820 585 545 0.261
ND180M 174 250 875 705 585 0.361
ND180L 204 280 875 705 585 0.361
ND200L 254 366 1025 825 700 0.592
ND225S 350 462 1025 825 700 0.592
ND225M 380 492 1025 825 700 0.592
ND250S 460 586 1150 845 710 0.690
ND250M 500 628 1150 845 710 0.690
ND280S 620 766 1300 915 745 0.886
ND280M 700 846 1300 915 745 0.886
ND315S 1056 1319 1600 1170 925 1.732
ND315M 1130 1393 1600 1170 925 1.732
ND315L 1200 1475 1700 1170 940 1.870
ND355L 2150 2553 1900 1375 1325 3.462
8 8
TEFC
SQUIRREL CAGE
MOTORS
9 9
TEFC
SQUIRREL CAGE
MOTORS
L
Ø AC
CABLE ENTRY
SCREWED FOR
TAPPED HOLE KK BS CONDUIT FOR
Y × DEPTH CABLE GLAND
GE
N9/h9
X ED ED X
F
HD
D D H
G GD
BA AA
GA 4 HOLES HA
E C B E A
K DIA
BB AB
AD63 100 80 40 63 25.5 122 – 96 7 9 11 23 18 4 8.5 12.5 4 2.5 2..5 M4×10 125 210 160 3/4"
AD71 112 90 45 71 30 136 – 110 7 9 14 30 25 5 11 16 5 3 2.5 M5×12.5 145 250 175 3/4"
TOLERANCE
+ 0.0
H – ALL + 0.0
– 0.5 F N9 3 TO 6
– 0.030
SHAFT
+ 0.2
ED – UP TO 28 – 0.0
+ 0.008
D j6 11 TO 18 – 0.003
KEY
+ 0.1
GE – UP TO 3.5 – 0.0 F h9 + 0.0
3 TO 6
– 0.030
1. All dimensions are in mm, unless specified.
2. Cable entries can be rotated through 360° in
GD 3 TO 6 + 0.0
steps of 90°. h9
– 0.030
3. Compression type cable glands can be fitted
when specified.
4. All dimensions are subject to confirmation.
Certified Drawings will be sent on request.
10
TEFC
SQUIRREL CAGE
MOTORS
L
R
E LB E
CABLE ENTRY
TAPPED HOLE SCREWED FOR KK
Y X DEPTH X ED ED X BS CONDUIT FOR
CABLE GLAND
GE N9/h9
F HB
D Ø N Ø AC
SPIGOT
D D
45°
G GD
GA
P T LA
4 HOLES DRILLED Ø S
EQUALLY SPACED ON
M DIA. CIRCLE
AD63D 115 95 140 0 10 3 9 11 23 18 4 8.5 12.5 4 2.5 2.5 M4×10 125 220 197 100 3/4 ''
AD71D 130 110 160 0 10 3.5 9 14 30 25 5 11 16 5 3 2.5 M5×12.5 145 250 220 105 3/4 ''
TOLERANCE
M – UP TO 265 ± 0.03
3 TO 6 + 0.0
F N9
– 0.030
SPIGOT
+ 0.013 ED – + 0.2
N j6 UP TO 28
95 TO 110 – 0.009 – 0.0
KEY
SHAFT
F h9 3 TO 6 + 0.0
D j6 + 0.008 – 0.030
11 TO 18 – 0.003
GD h9 3 TO 6 + 0.0
+ 0.1
GE – UP TO 3.5 – 0.030
– 0.0
11
TEFC
SQUIRREL CAGE
MOTORS
L CABLE ENTRY
SCREWED FOR
LB KK BS CONDUIT
R
45° FOR CABLE GLAND
TAPPED HOLE
Y × DEPTH
GE
N9/h9 X ED
HB ED X
F
D Ø AC
Ø N
SPIGOT
Ø P D D
G GD
GA E
4 HOLES TAPPED S Ø × LA DEEP EQUALLY E
SPACED ON M DIA CIRCLE T
AD63C 75 60 90 0 M5 2.5 8 11 23 18 4 8.5 12.5 4 2.5 2.5 M4×10 125 220 197 100 3/4''
AD71C 85 70 105 0 M6 2.5 10 14 30 25 5 11 16 5 3 2.5 M5×12.5 145 250 215 105 3/4''
TOLERANCE
+ 0.012 + 0.2
N j6 50 TO 80 ED – UP TO 28 – 0.0
– 0.007
KEY
SHAFT
+ 0.0
F h9 3 TO 6 – 0.030
D j6 + 0.008
11 TO 18
– 0.003
+ 0.0
+ 0.1 GD h9 3 TO 6
GE – UP TO 3.5 – 0.030
– 0.0
12
TEFC
SQUIRREL CAGE
MOTORS
L Ø AC
TAPPED HOLE
CABLE ENTRY
Y × DEPTH SCREWED FOR
GE KK BS CONDUIT
N9/h9 FOR CABLE GLAND
F ED ED
HD
D D
H
G GD
4 SLOTTED
BA HOLES ØK × V AA
GA LONG HA
E C B E A
BB AB
ØK
AD 80 125 100 50 80 28 152 35 125 10 14 11 19 40 27 6 15.5 21.5 6 3.5 M6×16 165 285 200 3/4"
TOLERANCE
+ 0.0
H – ALL + 0.0
– 0.5 F N9 3 TO 6 – 0.030
SHAFT
ED – UP TO 28 + 0.2
j6 + 0.009 – 0.0
D 19 TO 28
– 0.004
KEY
+ 0.1
GE – UP TO 3.5 + 0.0
- 0.0 F h9 3 TO 6
– 0.030
GD h9 + 0.0
3 TO 6 – 0.030
13
TEFC
SQUIRREL CAGE
MOTORS
L
R CABLE ENTRY
P E LB SCREWED FOR KK
45°
TAPPED HOLE BS CONDUIT FOR
CABLE GLAND
Y × DEPTH
GE N9/h9
F HB ED ED
Ø N
D Ø AC
SPIGOT
D D
G GD
GA
T LA E
4 HOLES DRILLED S DIA
EQUALLY SPACED ON M
DIA CIRCLE
AD80D 165 130 200 0 12 3.5 10 19 40 27 6 15.5 21.5 6 3.5 M6×16 165 285 245 120 3/4 "
TOLERANCE
+ 0.014 + 0.2
N j6 120 TO 180 ED – UP TO 28
– 0.011 – 0.0
KEY
SHAFT
+ 0.0
F h9 3 TO 6 – 0.030
D j6 19 TO 28 + 0.009
– 0.004
GD h9 + 0.0
+ 0.1 3 TO 6
GE – UP TO 3.5 – 0.030
- 0.0
14
TEFC
SQUIRREL CAGE
MOTORS
L
CABLE ENTRY
R SCREWED FOR
LB
E KK BS CONDUIT
45°
FOR CABLE GLAND
TAPPED HOLE
Y × DEPTH
GE
N9/h9 HB ED
F ED
Ø N Ø AC
D
SPIGOT
P D D
G GD
GA
4 HOLES TAPPED Ø S ×LA DEEP T E
EQUALLY SPACED ON M DIA CIRCLE
AD80C 100 80 120 0 M6 3 15 19 40 27 6 15.5 21.5 6 3.5 M6×16 165 285 245 120 3/4 "
TOLERANCE
+ 0.012 ED – + 0.2
N j6 50 TO 80 UP TO 28
– 0.007 – 0.0
KEY
SHAFT
+ 0.0
F h9 3 TO 6
D + 0.009 – 0.030
j6 19 TO 28 – 0.004
+ 0.1 GD + 0.0
GE – h9 3 TO 6
UP TO 3.5 – 0.030
– 0.0
15
TEFC
SQUIRREL CAGE
MOTORS
L Ø AC
CABLE ENTRY
SCREWED FOR
KK BS CONDUIT
FOR CABLE GLAND
TAPPED HOLE E
Y × DEPTH GE
ED
N9/h9 ED
F HD
D D
H
G GD HA
GA
AA
BA
E C B A 4 SLOTTED
HOLES
ØK × V LONG
BB AB
AD100L 160 140 63 100 48 192 35 170 12 16 13 28 60 44 8 24 31 7 4 M10×22 205 360 250 1"
TOLERANCE
+ 0.3
+ 0.009 ED – 32 TO 80 – 0.0
D j6 19 TO 28
– 0.004
KEY
+ 0.2
GE – 4 & ABOVE + 0.0
– 0.0 F h9 8 TO 10
– 0.030
1. All dimensions are in mm, unless specified.
2. Cable entries can be rotated through 360° in
steps of 90°. h11 + 0.0
GD 7 TO 10
3. Compression type cable glands can be fitted – 0.090
when specified.
4. All dimensions are subject to confirmation.
Certified Drawings will be sent on request.
16
TEFC
SQUIRREL CAGE
MOTORS
L CABLE ENTRY
SCREWED FOR
E R KK BS CONDUIT
FOR CABLE GLAND
TAPPED HOLE
Y × DEPTH GE AD E
N9/h9 45° ED ED
F
Ø N
D Ø AC
SPIGOT
D D
G GD P
GA
4 HOLES DRILLED EARTHING HOLE ON
Ø S EQUALLY SPACED T LA BOTH SIDES OF MOTOR
ON M DIA. CIRCLE BODY
LB
M N P R S T LA D E ED F G GA GD GE Y×Depth AD AC L LB KK
AD100LD 215 180 250 0 15 4 11 28 60 44 8 24 31 7 4 M10×22 150 205 360 300 1"
TOLERANCE
+ 0.014 + 0.3
N j6 120 TO 180 ED – 32 TO 80
– 0.011 – 0.0
SHAFT KEY
F h9 + 0.0
j6 + 0.009 8 TO 10
D 19 TO 28 – 0.030
– 0.004
17
TEFC
SQUIRREL CAGE
MOTORS
L CABLE ENTRY
45°
SCREWED FOR
KK BS CONDUIT
E R
FOR CABLE GLAND
TAPPED HOLE ED
GE AD
Y × DEPTH E
N9/h9
ED
F
D Ø N Ø AC
SPIGOT
Ø P D D
G
GD
GA
AD100 LC 130 110 160 0 M8 3.5 10 28 60 44 8 24 31 7 4 M10×22 150 205 360 300 1"
TOLERANCE
+ 0.013 + 0.3
N j6 80 TO 120 ED – 32 TO 80
– 0.009 – 0.0
KEY
SHAFT
+ 0.0
F h9 8 TO 10
j6 + 0.009 – 0.030
D 19 TO 28
– 0.004
h11 + 0.0
+ 0.2 GD 7 TO 10
GE – 4 & ABOVE – 0.090
– 0.0
18
TEFC
SQUIRREL CAGE
MOTORS
Ø AC
NO EYE BOLT
L E AD FOR ND 90 S/L
GE
TAPPED HOLE
Y × DEPTH N9 /h9 ED ED
F
HD
D HC
D D H
G GD
GA
BA HA AA
E C B CABLE ENTRIES A 4 HOLES
SCREWED FOR
BB 25.4 (1") BS CONDUIT AB K DIA.
FOR CABLE GLAND
ND100LX 370
160 140 63 100 36 192 45 170 12 13 28 60 44 8 24 31 7 4 M10×22 160 210 205 250
ND100L 380
ND112MX 390
90 140 70 112 36 222 50 170 12 13 28 60 44 8 24 31 7 4 M10×22 170 230 230 275
ND112M 405
TOLERANCE
+ 0.0 + 0.0
H – ALL F N9 8 TO 10
– 0.036
– 0.5
ED – + 0.3
SHAFT 32 TO 80
– 0.0
j6 + 0.009 KEY
19 TO 28 – 0.004
D + 0.0
+ 0.018 F h9 8 TO 10
k6 32 TO 48 – 0.036
+ 0.002
+ 0.2 + 0.0
GE – 4 & ABOVE GD h11 7 TO 10
– 0.0 – 0.090
1. All dimensions are in mm, unless specified. 4. Compression type cable glands can be fitted
2. Cable entries can be rotated through 360° in when specified.
steps of 90°. 5. All dimensions are subject to confirmation.
3. One cable entry for DOL starting and two for star / Certified Drawings will be sent on request.
delta starting and multispeed motors are provided.
19
TEFC
SQUIRREL CAGE
MOTORS
AD L
R
45 LB E
° E
NO EYE BOLT FOR
ED ND 90 SD/LD ED
GE
P
TAPPED HOLE
Y × DEPTH
N9 / h9 HB
F
Ø N Ø AC
D
SPIGOT
D D
G GD
4 HOLE DRILLED
CABLE ENTRIES
GA S Ø EQUALLY SCREWED FOR
SPACED ON M 25.4 (1") BS CONDUIT LA
T
DIA CIRCLE FOR CABLE GLAND
TOLERANCE
1. All dimensions are in mm, unless specified. 4. Compression type cable glands can be fitted
2. Cable entries can be rotated through 360° in when specified.
steps of 90°. 5. All dimensions are subject to confirmation.
3. One cable entry for DOL starting and two for star / Certified Drawings will be sent on request.
delta starting and multispeed motors are provided.
20
TEFC
SQUIRREL CAGE
MOTORS
AD L
R
LB E
E
45 NO EYE BOLT FOR
° ND 90 SC/LC
ED ED
TAPPED HOLE GE
Y × DEPTH HB
N9 / h9
F
D Ø N
Ø AC
SPIGOT
D D
G GD
4 HOLES TAPPED CABLE ENTRIES
Ø S × LA DEEP SCREWED FOR
GA P 25.4 (1") BS CONDUIT LA
EQUALLY SPACED T
ON M DIA CIRCLE FOR CABLE GLAND
TOLERANCE
j6 + 0.009 + 0.0
19 TO 28 – 0.004 F h9 8 TO 10 – 0.030
D
k6 + 0.018
32 TO 48
+ 0.002
+ 0.0
+ 0.2 GD h11 7 TO 10 – 0.090
GE – 4 & ABOVE
– 0.0
1. All dimensions are in mm, unless specified. 4. Compression type cable glands can be fitted
2. Cable entries can be rotated through 360° in when specified.
steps of 90°. 5. All dimensions are subject to confirmation.
3. One cable entry for DOL starting and two for Certified Drawings will be sent on request.
star / delta starting and multispeed motors are
provided.
21
TEFC
SQUIRREL CAGE
MOTORS
CABLE DIVIDING BOX PROVIDED AUXILIARY TERMINAL BOX FOR SPACE HEATER
FOR ND 200 ONWARDS & THERMISTOR ABOVE 200 FRAME ONLY
'Y'THREADED
CENTRE HOLES
L±5 AC
Y × DEPTH
AD
N9/h9 F +0.0
-0.5
GD ED
HD
H
ØD
BA AA
E±0.5 C±1 B±0.5 HA
A±0.5
B'±0.5
AB
BB
CABLE ENTRY 4-HOLES 'K' DIA.
SCREWED FOR
'KK'B.S.CONDUIT EARTHING TERMINALS OF M8 SIZE ON
BOTH SIDES. THESE SHALL BE M12
FOR 280 AND 315 FRAMES.
2 Nos.-1"
254 108 159.7 73 308 76 15.0 42.002 110 80 11.957 7.91 36.8 265 318 650 376 22
ND160L 254 - 298
M16×32
ND180M 241 - 180.0 286 15.5 48.018 14.00 9.00 42.5 668
279 121 84 348 95 110 80 285 352 418 22
ND180L 279 - 179.7 323 15.0 48.002 13.957 8.91 43.3 706
19.5 55.030 16.00 10.00 49.0
ND200L 318 305 - 133 200.0 64 381 104 356 110 80 345 405 775 464 25
199.5 19.0 55.011 15.957 9.91 48.8
ND225S 286 - 225.0 19.5 60.030 18.00 11.00 53.0
2 Nos.-1.5"
356 149 70 425 102 375 140 110 375 448 840 520 25
ND225M - 311 224.5 19.0 60.011 17.957 10.91 52.8
508 216 110 597 164 533 170 140 510 590 1200 725 38
ND315M - 457 314.0 28.0 80.011 21.948 13.91 70.8
ND355L 355.0 28.5 100.035 28.00 14.00 90.0 630 720 1570 827 40
610 630 - 254 110 710 250 857 210 160
⊗ 354.0 28.0 100.013 27.948 13.89 89.8
GD L
FRAME D E ED F TOLERANCE G
TOLERANCE S M L
ND16OM 55.030 / 55.011 110 80 16.0 / 15.957 10.0 / 9.91 49.0 / 49.8 810 810 –
ABOVE 200 FRAMES
MACHINES RUNNING ND16OL 60.030 / 60.011 140 110 18.0 / 17.957 11.0 / 10.91 53.0 / 52.8 930 930 –
AT 3000 RPM HAVE ND18OM 1075 1075 –
SMALLER SHAFTS 65.030 / 65.011 140 110 18.0 / 17.957 11.0 / 10.91 58.0 / 57.8
AS SHOWN HERE ND18OL 1170 1170 –
ND225S 70.030 / 70.011 140 110 20.0 / 19.948 12.0 / 11.91 62.0 / 62.3 – – 1345
ND225M 85.035 / 85.013 170 140 22.0 / 21.948 14.0 / 13.89 76.0 / 75.8 – – 1530
⊗ Frames having suffix 'S' are not available. For notes, please refer page 23.
22 22
TEFC
SQUIRREL CAGE
MOTORS
+0.0
N9/h9 F -0.5
ED
GD
HD
G
H
ØD
23
TEFC
SQUIRREL CAGE
MOTORS
CABLE ENTRY SCREWED FOR 'KK' CABLE DIVIDING BOX PROVIDED FOR
B.S.CONDUIT 200 FRAME ONWARDS
AUXILIARY TERMINAL BOX FOR SPACE HEATER/
'Y' THREADED THERMISTORS ABOVE 200 FRAME ONLY. 2-EYE BOLTS FOR
CENTRE HOLES AD 200 AND ABOVE
Y × DEPTH
L± 5 AC
N9 / h9
F
+0.0
GD -0.5
ED
HD
ØD H
BA HA AA
E ± 0.5 C ±1 B ±0.5
B' ± 0.5 4-HOLES 'K' DIA. A ± 0.5
BB AB
2Nos.-1"
ND160L 254 - 159.7 298 15.0 42.002 11.957 7.91 36.8 650
M16×32
ND180M 241 - 180.0 286 15.5 48.018 14.00 9.00 42.5 668
279 121 179.7 84 348 95 110 80 – 352 465 22
ND180L 279 - 323 15.0 48.002 13.957 8.91 42.3 706
200.0 19.5 55.030 16.00 10.00 49.0
ND200L 318 305 - 133 199.5 64 381 104 356 110 80 285 405 775 545 25
19.0 55.011 15.957 9.91 48.8
ND225S 286 - 225.0 19.5 60.030 140 110 18.00 11.00 53.0
356 149 70 425 102 375 285 448 840 600 25 2Nos.-1.5"
ND225M - 311 224.5 19.0 60.011 17.957 10.91 53.8
ND250S 311 - 250.0 24.5 65.030 18.00 11.00 58.0 M20×40 930
406 168 80 483 135 419 140 110 285 486 645 32
ND250M - 349 249.5 24.0 65.011 17.957 10.91 57.8 930
L
FRAME D TOLERANCE E ED F TOLERANCE GD TOLERANCE G
S M L
ND225 55.030 / 55.011 110 80 16.0 / 15.957 10.0 / 9.91 49.0 / 48.8 810 810 –
ABOVE 200 FRAMES
MACHINES RUNNING ND250 60.030 / 60.011 140 110 18.0 / 17.957 11.0 / 10.91 53.0 / 52.8 930 930 –
AT 3000 RPM HAVE ND280 1075 1075 –
SMALLER SHAFTS 65.030 / 65.011 140 110 18.0 / 17.957 11.0 / 10.91 58.0 / 57.8
AS SHOWN HERE ND315 1170 1170 –
ND315L 70.030 / 70.011 140 110 20.0 / 19.948 12.0 / 11.91 62.5 / 62.3 – – 1345
Terminals Box position for ND280S/M is approximately at centre. For notes, please refer page 23, except that cable entry cannot be from
non-driving end.
24
TEFC
SQUIRREL CAGE
MOTORS
AUXILIARY TERMINAL BOX FOR SPACE HEATER/THERMISTORS ABOVE 200 FRAME ONLY CABLE ENTRY SCREWED
FOR 'KK' CONDUIT
4 - HOLES FOR FRAME 160 - 200 EYEBOLT FOR VERTICALLY
8 - HOLES FOR FRAME 225 - 315 MOUNTED MOTORS ABOVE 200 FRAME ONLY
DRILLED Ø 'S' ON 'M' P.C.D.
CONCENTRICITY
EQUALLY SPACED AS SHOWN L±5
AD LB
N9 / h9 F
GD
+ 0.0
°
45 - 0.5
ED
Ø N SPIGOT
22.5
Ø AC
ØP
G
(E)
HB
ØD
+0
'PERPENDICULARITY E +2
LA
2 Nos.-1"
ND160MD 42.018 12.00 8.00 37.0 640 213
18 110 80 265 318 432
ND160LD 300.5 250.016 42.002 11.957 7.91 36.8 685 235
350 19 5 M16×32
299.5 249.987 48.018 14.00 9.00 42.5
ND180MD 708 241.5
18 110 80 285 352 476
ND180LD 48.002 13.957 8.91 42.3 746 260.5
350.5 300.018 55.030 16.00 10.00 49.0
ND200LD 400 19 5 18 110 80 345 405 810 285.5 528
349.5 299.982 55.011 15.957 9.91 48.8
M20×40
2 Nos.-1.5"
ND225SD 400.5 350.018 60.030 18.00 11.00 53.0
450 19 5 19 140 110 375 448 855 304.5 590
ND225MD 399.5 349.982 60.011 17.957 10.91 52.8
L
FRAME D TOLERANCE E ED F TOLERANCE GD TOLERANCE G
SD MD LD
ND225 55.030 / 55.011 110 80 16.0 / 15.957 10.0 / 9.91 49.0 / 49.8 855 855 –
ABOVE 200 FRAMES
MACHINES RUNNING ND250 60.030 / 60.011 140 110 18.0 / 17.957 11.0 / 10.91 53.0 / 52.8 975 975 –
AT 3000 RPM HAVE ND280 1120 1120 –
SMALLER SHAFTS 65.030 / 65.011 140 110 18.0 / 17.957 11.0 / 10.91 58.0 / 57.8
AS SHOWN HERE ND315 122 122 –
ND315 70.030 / 70.011 140 110 20.0 / 19.948 12.0 / 11.91 62.5 / 62.3 – – 1395
25
TEFC
SQUIRREL CAGE
MOTORS
N9 / H9
GD
+0.0
F ED-0.5
HD
N SPIGOT
ØP
G
(E)
H
ØD
+0
E +2 C ±1 B ± 0.5 BA HA AA A ±0.5
Y-THREADED CENTRE B' ± 0.5 AB
PERPENDICULARITY BB
Y × DEPTH
CABLE ENTRY SCREWED FOR 'KK' B.S. CONDUIT 4-HOLES "K" DIA.
26
TEFC
SQUIRREL CAGE
MOTORS
OVERALL D F GD
FRAME FRAME E ED G Y
TOLERANCE TOLERANCE TOLERANCE
AD AC L LB HD HA KK
ND225SH 55.030 16.00 10.0 49.0
ND160MH 605 213 110 80 810
265 318 376 22 ND225MH 55.011 15.957 9.91 48.8
2Nos.-1"
ND160LH 650 235
ABOVE 200 FRAMES ND250SH
ND180MH 668 241.5 60.030 18.00 11.00 53.0 930
MACHINES RUNNING 140 110
285 352 418 22 ND250MH 60.011 17.957 10.91 52.3 930
ND180LH 706 260.5 AT 3000 RPM HAVE
ND280SH 65.030 18.00 11.00 58.0
ND200LH 345 405 775 285.5 464 25 SMALLER SHAFTS 140 110 1075
ND280MH 65.011 17.957 10.91 57.8
AS SHOWN HERE
ND225SH
375 448 840 304.5 520 25 ND315SH 53.0 1170
2Nos.-1.5"
27
TEFC
SLIP RING
MOTORS
28
TEFC
SLIP RING
MOTORS
PERFORMANCE DATA
Supply : 415V or 380V, 50 Hz, 3 Phase AC Voltage Variation : ± 10%
Enclosure : Totally Enclosed Fan Cooled (TEFC) Frequency Variation : ± 5%
Degree of Protection : IP55 Combined Variation : ± 10%
Rating: Continuous, Duty : S1 Mounting : B3, Ambient : 45° C
Insulation Class : ‘F’ Temperature Rise by Resistance Method : 75°C Max.
P
OUTPUT FL FL EFFICIENCY (%) POWER FACTOR OPEN CIRCUIT ROTOR NETT
O FL GD²
FRAME AMPS AMPS ROTOR VOLTAGE CURRENT WEIGHT
L RPM 3/4 1/2 3/4 1/2 KgM²
kW HP 380 V 415 V FL FL VOLTS AMPS Kg.
E FL FL FL FL
1.5 2.0 8 DW132S 680 4.5 70.0 67.0 63.0 0.61 0.51 0.40 110 8.5 0.33 88
2.2 3.0 4 DW132S 1410 4.5 78.0 76.0 74.0 0.85 0.79 0.71 110 13.5 0.17 88
2.2 3.0 6 DW132S 940 6.0 77.0 75.0 71.0 0.72 0.62 0.50 110 12.0 0.33 88
2.2 3.0 8 DW132M 690 5.7 75.0 74.0 71.0 0.65 0.55 0.44 110 13.0 0.40 111
3.0 4.0 4 DW132S 1410 6.0 80.0 78.0 74.0 0.80 0.74 0.66 110 17.0 0.17 88
3.0 4.0 6 DW132M 940 7.6 79.0 78.0 75.0 0.69 0.64 0.53 110 16.0 0.40 111
3.0 4.0 8 NDW160M 690 8.5 7.5 80.0 79.0 77.0 0.68 0.64 0.56 230 8.0 0.58 132
3.7 5.0 4 DW132S 1400 8.0 79.0 78.0 75.0 0.84 0.79 0.70 110 23.0 0.17 88
3.7 5.0 6 DW132M 930 9.0 81.0 80.0 77.0 0.70 0.62 0.50 110 18.0 0.40 111
3.7 5.0 8 NDW160M 710 10.5 10.0 81.0 80.0 78.0 0.68 0.64 0.56 230 10.0 0.58 141
5.5 7.5 4 DW132M 1430 12.0 81.0 78.0 74.0 0.80 0.72 0.62 110 33.0 0.20 111
5.5 7.5 6 NDW160M 940 13.5 12.0 83.0 82.0 80.0 0.76 0.74 0.66 180 18.5 0.58 141
5.5 7.5 8 NDW160L 710 15.0 14.0 82.0 81.0 79.0 0.68 0.64 0.56 360 10.0 0.80 165
7.5 10.0 4 NDW160M 1440 16.5 15.0 83.0 82.0 80.0 0.84 0.80 0.72 350 13.0 0.48 141
7.5 10.0 6 NDW160L 940 18.0 16.5 83.0 82.0 80.0 0.76 0.72 0.64 260 19.0 0.77 165
7.5 10.0 8 NDW180L 710 20.0 18.0 84.0 83.0 81.0 0.68 0.64 0.56 350 13.0 1.58 235
9.3 12.5 4 NDW160L 1440 20.0 18.0 84.0 83.0 81.0 0.84 0.80 0.72 350 16.0 0.35 165
9.3 12.5 6 NDW180M 950 20.0 18.0 86.0 85.0 83.0 0.82 0.78 0.70 230 24.0 1.33 205
9.3 12.5 8 NDW200L 725 24.5 22.0 86.0 85.0 83.0 0.68 0.64 0.76 300 19.5 2.68 285
11.0 15.0 4 NDW160L 1440 24.0 22.0 84.0 83.0 81.0 0.84 0.80 0.72 350 19.0 0.35 165
11.0 15.0 6 NDW180L 950 24.0 22.0 86.0 85.0 83.0 0.82 0.78 0.70 230 28.5 1.58 235
11.0 15.0 8 NDW200L 725 28.0 26.0 87.0 86.0 84.0 0.68 0.64 0.56 300 23.0 2.68 285
15.0 20.0 4 NDW180L 1445 31.0 28.0 88.0 87.0 85.0 0.84 0.80 0.72 350 27.0 1.25 235
15.0 20.0 6 NDW200L 970 31.0 28.5 89.0 88.0 86.0 0.82 0.78 0.70 295 31.0 2.68 285
15.0 20.0 8 NDW225M 730 37.5 34.0 87.0 86.0 84.0 0.70 0.66 0.58 350 27.0 3.06 410
18.5 25.0 4 NDW200L 1470 38.0 34.0 89.0 88.0 86.0 0.84 0.80 0.72 300 36.0 2.18 285
18.5 25.0 6 NDW225M 970 38.5 36.0 89.0 88.0 86.0 0.82 0.78 0.70 310 37.0 2.87 410
18.5 25.0 8 NDW225M 730 46.0 42.0 88.0 87.0 85.0 0.70 0.66 0.58 360 32.0 3.63 410
22.0 30.0 4 NDW200L 1470 44.5 40.0 89.0 88.0 86.0 0.85 0.81 0.73 390 33.0 2.34 285
22.0 30.0 6 NDW225M 970 46.0 42.0 89.0 88.0 86.0 0.82 0.78 0.70 310 45.0 3.25 410
22.0 30.0 8 NDW250M 730 50.0 45.0 91.0 90.0 88.0 0.74 0.70 0.62 250 55.0 6.81 540
30.0 40.0 4 NDW225M 1470 60.0 55.0 89.0 88.0 86.0 0.85 0.81 0.73 380 47.0 2.96 410
30.0 40.0 6 NDW250M 975 61.0 55.0 91.0 90.0 88.0 0.82 0.78 0.70 320 56.0 6.81 540
30.0 40.0 8 NDW280S 735 68.0 62.0 91.0 90.0 88.0 0.74 0.70 0.62 440 43.0 12.89 670
37.0 50.0 4 NDW250M 1475 73.0 67.0 90.0 89.0 87.0 0.85 0.81 0.73 425 52.0 4.96 540
37.0 50.0 6 NDW280S 980 74.0 67.0 91.0 90.0 88.0 0.84 0.80 0.72 410 57.0 12.89 670
37.0 50.0 8 NDW280M 735 83.0 76.0 91.0 90.0 88.0 0.74 0.70 0.62 520 45.0 15.14 750
45.0 60.0 4 NDW250M 1475 89.0 82.0 90.0 89.0 87.0 0.85 0.81 0.73 445 60.0 5.70 540
45.0 60.0 6 NDW280M 980 88.0 81.0 91.5 91.0 89.0 0.85 0.81 0.73 320 87.0 15.14 750
45.0 60.0 8 NDW315S 735 102.0 93.0 91.0 90.0 88.0 0.74 0.70 0.62 320 88.0 21.66 1106
55.0 75.0 4 NDW280S 1480 106.0 97.0 91.5 91.0 89.0 0.86 0.82 0.74 460 73.0 10.61 670
55.0 75.0 6 NDW315S 980 107.0 98.0 92.0 91.0 89.0 0.85 0.81 0.73 535 62.0 22.00 1106
55.0 75.0 8 NDW315M 735 122.0 112.0 91.0 90.0 88.0 0.75 0.71 0.63 320 108.0 24.16 1180
75.0 100.0 4 NDW280M 1480 142.0 130.0 92.5 92.0 90.0 0.87 0.83 0.75 490 92.0 12.45 750
75.0 100.0 6 NDW315M 980 144.0 132.0 93.0 92.0 90.0 0.85 0.81 0.73 470 96.0 24.16 1180
75.0 100.0 8 NDW315L 740 150.0 138.0 92.5 92.0 90.0 0.82 0.78 0.70 400 113.0 36.73 1260
29
TEFC
SLIP RING
MOTORS
30
TEFC
SLIP RING
MOTORS
SHIPPING SPECIFICATIONS
FOOT MOUNTED MOTORS,
TERMINAL BOX ON SIDE
NETT WEIGHT GROSS WEIGHT DIMENSIONS VOLUME
FRAME
KG KG L IN MM B IN MM H IN MM CUBIC METRES
DW132S 88 126 815 550 485 0.22
DW132M 111 149 815 550 485 0.22
NDW160M 141 243 1165 710 700 0.58
NDW160L 165 267 1165 710 700 0.58
NDW180M 205 311 1025 825 700 0.59
NDW180L 235 341 1025 825 700 0.59
NDW200L 285 423 1300 915 745 0.89
NDW225S 380 518 1300 915 745 0.89
NDW225M 410 548 1300 915 745 0.89
NDW250S 500 638 1300 915 745 0.89
NDW250M 540 678 1300 915 745 0.89
NDW280S 670 884 1500 1065 850 1.36
NDW280M 750 964 1500 1065 850 1.36
NDW315S 1106 1359 1600 1170 925 1.73
NDW315M 1180 1433 1600 1170 925 1.73
NDW315L 1260 1613 1830 1270 1156 2.69
31
TEFC
SLIP RING
MOTORS
L E
Ø AC
SLIPRING MAINTAINANCE
COVER AT OPPOSITE
ENDS AD
TAPPED HOLE
Y × DEPTH ED ED
GE
N9/h9
F
HD
D HC
D D H
G GD
GA BA HA
AA 4 HOLES K DIA
2-CABLE ENTRIES
SCREWED FOR KK BS
E C B CONDUIT FOR CABLE A
GLAND
BB AB
TOLERANCE
ON GRADE RANGE TOLERANCE ON GRADE RANGE TOLERANCE
CENTRE HEIGHT KEYWAY
+ 0.0
H – ALL + 0.0
– 0.5 F N9 8 TO 10
– 0.036
SHAFT
+ 0.3
+ 0.018 ED – 32 TO 80 – 0.0
D k6 32 TO 48 + 0.002
KEY
+ 0.2
GE – 4 & ABOVE – 0.0 + 0.0
F h9 8 TO 10
– 0.036
1. All dimensions are in mm, unless specified.
2. Cable entries can be rotated through 360° in
steps of 90°. h11 + 0.0
GD 7 TO 10
3. Compression type cable glands can be fitted – 0.090
when specified.
4. All dimensions are subject to confirmation.
Certified Drawings will be sent on request.
32
TEFC
SLIP RING
MOTORS
L E
AD
R
E LB
TAPPED HOLE 45 ED
°
Y × DEPTH
ED
GE
N9/h9
HB
F
N DIA.
D Ø AC
SPIGOT
D D
G GD
P Ø
SLIPRING MAINTAINANCE
GA T
2 - CABLE ENTRIES SCREWED COVER AT OPPOSITE ENDS.
4 - HOLES DRILLED FOR 25.4 MM (1") BS CONDUIT LA
S DIA. ON M DIA. CIRCLE. FOR CABLE GLAND
TOLERANCE
+ 0.016 + 0.3
N j6 180 TO 250 ED – 32 TO 80
– 0.013 – 0.0
SHAFT KEY
F h9 8 TO 10 + 0.0
k6 + 0.018
D 32 TO 48 – 0.030
+ 0.002
33
TEFC
SLIP RING
MOTORS
AD L
R
LB E
E
45°
ED ED
TAPPED HOLE
GE
Y × DEPTH
HB
N9 / h9
F
Ø N
D Ø AC
SPIGOT
D
D
G GD
GA
4 HOLES TAPPED P 2 CABLE ENTRIES T
S Ø ×'LA' DEEP SCREWED FOR SLIPRING
MAINTAINANCE
EQUALLY SPACED 25.4(1") BS CONDUIT COVER AT OPPOSITE
ON M DIA CIRCLE FOR CABLE GLAND SIDES
TOLERANCE
+ 0.014 + 0.3
N j6 120 TO 180 ED – 32 TO 80
– 0.009 – 0.0
SHAFT KEY
F h9 8 TO 10 + 0.0
k6 + 0.018
D 32 TO 48 – 0.036
+ 0.002
34
TEFC
SLIPRING
MOTORS
L E
AD
R
E LB
TAPPED HOLE 45 ED
°
Y × DEPTH
ED
GE
N9/h9
HB
F
N DIA.
D Ø AC
SPIGOT
D D
G GD
P Ø
SLIPRING MAINTAINANCE
GA T
2 - CABLE ENTRIES SCREWED COVER AT OPPOSITE ENDS.
4 - HOLES DRILLED FOR 25.4 MM (1") BS CONDUIT LA
S DIA. ON M DIA. CIRCLE. FOR CABLE GLAND
DW180MD
300 250
– 0.013
+ 0.016
350 0 19 5 19 48
} + 0.013
– 0.002
110 80 14
36.7
42.5
51.5 315
748 638
768 658
415 260
DW180LD – 0.013 42.3 806 696
35
TEFC
SLIP RING
MOTORS
+0.0 +0.0
N9/h9 -0.5 -0.5
ED ED
F
A
HD
D
H
h
GA
E C B±0.3 BA AA
E HA
SEC. A - A B'±0.3 A±0.5
BB AB
CABLE ENT RY SCREWED
DOUBLE SHAF T EXTN. WHEN READ FOR 'KK' B.S.CONDUIT
4-HOLES 'K' DIA.
EA RTHING TERMINALS OF M8 SIZE
ON BOTH SIDES . THESE SHAL L BE
M12 FOR 280 AND ABOVE
2Nos.-1"
NDW160L 254 - 159.7 298 15.0 42.002 44.8 810 926
M16×32
NDW180M 241 - 180.0 286 15.5 48.018 51.5 840 956
279 121 84 348 95 110 80 14×9 285 352 418 22
NDW180L 279 - 179.7 323 15.0 48.002 51.3 878 994
200.0 19.5 55.030 49.0
NDW200L 318 305 - 133 199.5 64 381 104 356 16×10 345 405 952 1068 464 25
19.0 55.011 58.0
NDW225S 286 -
356 149 225.0 70 425 102 375 19.5 60.030 18×11 64.0 375 448 1072 1218 520 25
2Nos.-1.5"
NDW225M - 311 224.5 19.0 60.011 63.8
DW250S 311 - 381 24.5 65.030
406 168 250.0 79 483 127 140 110 18×11
69.0
M20×40 425 540
1054 1200
624 32
DW250M 349 - 249.5 419 24.0 65.011 68.8 1092 1238
NDW280S 368 - 280.0 24.5 75.030 79.5
457 190 100 538 198 487 20×12 430 540 1265 1415 642 35
NDW280M - 419 279.0 24.0 75.011 79.3
36
TEFC
SLIP RING
MOTORS
CABLE ENT RY SCREWED FOR 'KK' B.S.CONDUIT CABLE DIVIDING BOX PROVIDED FOR 200 FRAME ON WARDS
N9 / h9
F
GD
+0.0
+0.5
ED
HD
G
H
D
BA HA AA
E ± 0.5 C±1 B ± 0.5
B' ± 0.5 A ± 0.5
4-HOLES 'K' DIA.
BB AB
2Nos.-1"
NDW160L 254 - 159.7 298 15.0 42.002 11.957 7.91 36.8 810
M16×32
NDW180M 241 - 180.0 286 15.5 48.018 14.00 9.00 42.5 840
279 121 84 348 95 110 80 – 352 465 22
NDW180L 279 - 179.7 323 15.0 48.002 13.957 8.91 42.3 878
200.0 19.5 55.030 16.00 10.00 49.0
NDW200L 318 305 - 133 199.5 64 381 104 356 110 80 285 405 952 545 25
19.0 55.011 15.957 9.91 48.8
NDW225S 286 -
356 149 225.0 70 425 102 375 19.5 60.030 140 110 18.00 11.00 53.0 285 448 1072 600 25
2Nos.-1.5"
NDW225M - 311 224.5 19.0 60.011 17.957 10.91 53.8
M20×40
NDW250S 311 - 24.5 65.030 18.00 11.00 58.0
406 168 250.0 80 483 135 419 140 110 285 486 1128 645 32
NDW250M - 349 249.5 24.0 65.011 17.957 10.91 57.8
37
DRIP PROOF
SQUIRREL CAGE
MOTORS
38
DRIP PROOF
SQUIRREL CAGE
MOTORS
PERFORMANCE DATA
Supply : 415 V or 380 V, 50 Hz, 3 Phase AC Voltage Variation : ± 10%
Enclosure : Screen Protected, Drip Proof (SPDP) Frequency Variation : ± 5%
Degree of Protection : IP21 for C160 - 200
Combined Variation : ± 10%
IP23 for C225 - 315
Rating : Continuous, Duty: S1 Mounting : B3, Ambient : 45°C
Insulation Class : ‘F’ Temperature Rise by Resistance Method : 75°C Max.
P
OUTPUT FL FL EFFICIENCY (%) POWER FACTOR DOL STG. S/D STG. NETT
O FL GD²
FRAME AMPS AMPS WEIGHT
L RPM 3/4 1/2 3/4 1/2 STG. C STG. T STG. C STG. T KgM²
kW HP 380 V 415 V FL FL Kg.
E FL FL FL FL %FLC %FLT % FLC % FLT
3.7 5.0 8 C160M 700 9.5 9.0 82.0 81.0 79.0 0.74 0.70 0.62 500 200 140 55 0.55 121
5.5 7.5 8 C160M 700 14.0 13.0 82.0 81.0 79.0 0.74 0.70 0.62 500 200 140 55 0.55 121
7.5 10.0 6 C160M 950 17.0 16.0 84.0 83.0 81.0 0.80 0.76 0.68 500 200 140 55 0.42 121
7.5 10.0 8 C160L 700 19.0 17.0 82.0 81.0 79.0 0.74 0.70 0.62 500 200 140 55 0.65 131
9.3 12.5 2 C160M 2900 20.5 19.0 84.0 83.0 81.0 0.82 0.78 0.70 550 200 155 55 0.16 121
9.3 12.5 4 C160M 1450 21.0 19.0 86.0 85.0 83.0 0.78 0.74 0.66 550 200 155 55 0.38 121
9.3 12.5 6 C160L 950 21.0 19.0 84.0 83.0 81.0 0.80 0.76 0.68 500 200 140 55 0.54 131
9.3 12.5 8 C180M 700 21.5 20.0 84.0 83.0 81.0 0.78 0.74 0.66 500 200 140 55 1.14 185
11.0 15.0 2 C160M 2900 24.5 23.0 84.0 83.0 81.0 0.82 0.78 0.70 550 200 155 55 0.16 121
11.0 15.0 4 C160M 1450 24.5 22.0 86.0 85.0 83.0 0.80 0.76 0.68 550 200 155 55 0.38 121
11.0 15.0 6 C160L 950 25.0 23.0 84.0 83.0 81.0 0.80 0.76 0.68 500 200 140 55 0.62 131
11.0 15.0 8 C180M 700 24.5 23.0 85.0 84.0 82.0 0.80 0.76 0.68 500 200 140 55 1.14 185
15.0 20.0 2 C160M 2920 33.0 31.0 84.0 83.0 81.0 0.83 0.79 0.71 550 200 155 55 0.17 121
15.0 20.0 4 C160L 1450 33.0 30.0 87.0 86.0 84.0 0.80 0.76 0.68 550 200 155 55 0.48 131
15.0 20.0 6 C180M 960 33.0 30.0 85.0 84.0 82.0 0.82 0.78 0.70 600 225 170 60 1.14 185
15.0 20.0 8 C180L 700 33.5 31.0 85.0 84.0 82.0 0.80 0.76 0.68 500 200 140 55 1.45 205
18.5 25.0 2 C160L 2920 40.0 39.0 84.0 83.0 81.0 0.84 0.80 0.72 550 200 155 55 0.22 131
18.5 25.0 4 C160L 1450 40.0 36.0 88.0 87.0 85.0 0.80 0.76 0.68 550 200 155 55 0.68 131
18.5 25.0 6 C180L 960 38.0 36.0 87.0 86.0 84.0 0.85 0.81 0.73 600 225 170 60 1.33 205
18.5 25.0 8 C200M 720 44.0 41.0 86.0 85.0 83.0 0.74 0.70 0.62 500 150 140 40 2.20 260
22.0 30.0 2 C160L 2920 45.5 41.0 86.0 85.0 83.0 0.86 0.82 0.74 550 200 155 55 0.28 131
22.0 30.0 4 C180M 1450 45.0 41.0 87.0 86.0 84.0 0.86 0.82 0.74 600 200 170 55 0.91 185
22.0 30.0 6 C200M 960 44.0 40.0 89.0 88.0 86.0 0.86 0.82 0.74 600 200 170 55 1.91 260
22.0 30.0 8 C200L 720 52.0 48.0 87.0 96.0 84.0 0.74 0.70 0.62 500 150 140 40 2.58 300
30.0 40.0 2 C180M 2935 56.0 51.0 89.0 88.0 86.0 0.92 0.88 0.80 600 200 170 55 0.49 185
30.0 40.0 4 C180L 1450 59.0 54.0 88.0 87.0 85.0 0.88 0.84 0.76 600 200 170 55 1.15 205
30.0 40.0 6 C200L 960 59.0 53.0 89.0 88.0 86.0 0.87 0.83 0.75 600 200 170 55 2.58 300
30.0 40.0 8 C225M 720 70.0 64.0 88.0 87.0 85.0 0.74 0.70 0.62 500 150 140 40 3.35 340
37.0 50.0 2 C180L 2945 70.0 65.0 89.0 88.0 86.0 0.90 0.89 0.86 600 225 140 60 0.59 205
37.0 50.0 4 C200M 1455 73.0 68.0 90.0 89.0 87.0 0.85 0.81 0.73 550 225 155 60 1.79 260
37.0 50.0 6 C225M 960 69.0 64.0 92.0 91.0 89.0 0.88 0.84 0.76 600 200 170 55 3.35 340
37.0 50.0 8 C250S 720 79.0 72.0 89.0 88.0 86.0 0.80 0.76 0.68 500 150 140 40 5.38 425
45.0 60.0 2 C200M 2930 84.0 78.0 90.0 89.0 87.0 0.90 0.86 0.78 600 225 170 60 0.78 260
45.0 60.0 4 C200L 1455 86.0 79.0 90.0 89.0 87.0 0.88 0.84 0.76 550 225 155 60 2.11 300
45.0 60.0 6 C250S 970 86.0 79.0 92.0 91.0 89.0 0.86 0.82 0.74 600 200 170 55 5.39 425
45.0 60.0 8 C250M 725 95.0 88.0 89.5 89.0 87.0 0.80 0.76 0.68 500 150 140 40 6.66 480
55.0 75.0 2 C200L 2950 104.0 96.0 89.0 88.0 86.0 0.90 0.86 0.78 650 225 185 60 1.09 300
55.0 75.0 4 C225M 1460 108.0 99.0 90.0 89.0 87.0 0.86 0.82 0.74 600 225 170 60 2.73 340
55.0 75.0 6 C250M 970 103.0 96.0 92.0 91.0 89.0 0.88 0.84 0.76 600 200 170 55 6.66 480
55.0 75.0 8 C280S 730 131.0 120.0 91.0 90.0 88.0 0.70 0.66 0.60 500 200 140 55 10.10 620
75.0 100.0 2 C225M 2930 141.0 130.0 90.0 89.0 87.0 0.90 0.86 0.78 600 200 170 55 1.17 340
75.0 100.0 4 C250S 1475 145.0 133.0 92.5 92.0 90.0 0.85 0.81 0.73 550 175 155 50 4.51 425
93.0 125.0 2 C250S 2950 174.0 155.0 90.0 89.0 87.0 0.90 0.86 0.78 600 200 170 55 1.87 425
93.0 125.0 4 C250M 1475 180.0 163.0 92.5 92.0 90.0 0.85 0.81 0.73 550 175 155 50 5.60 480
39
DRIP PROOF
SQUIRREL CAGE
MOTORS
110.0 150.0 2 C250M 2950 206.0 188.0 90.0 89.0 87.0 0.90 0.86 0.78 600 200 170 55 4.70 480
110.0 150.0 4 C280S 1475 200.0 183.0 93.0 92.5 90.5 0.90 0.86 0.78 600 150 170 40 7.44 620
110.0 150.0 6 C315S 980 214.0 196.0 93.0 92.5 90.5 0.84 0.80 0.72 550 225 155 60 17.50 865
110.0 150.0 8 C315M 740 225.0 205.0 93.0 92.0 90.0 0.80 0.76 0.68 500 225 140 60 20.83 950
132.0 175.0 2 C280M 2930 248.0 227.0 90.0 89.0 87.0 0.90 0.86 0.78 600 150 170 40 5.00 710
132.0 175.0 4 C280M 1480 240.0 219.0 93.0 92.5 90.5 0.90 0.86 0.78 600 150 170 40 8.72 710
132.0 175.0 6 C315M 980 257.0 235.0 93.0 92.5 90.5 0.84 0.80 0.72 550 225 155 60 20.83 950
132.0 175.0 8 C315MX 740 270.0 246.0 93.0 92.0 90.0 0.80 0.76 0.68 500 120 140 35 30.00 1150
160.0 215.0 2 C315S 2940 294.0 268.0 92.0 91.0 89.0 0.90 0.86 0.78 600 140 170 40 7.45 865
160.0 215.0 4 C315S 1475 304.0 278.0 93.0 92.0 90.0 0.86 0.82 0.74 500 225 140 60 16.00 865
160.0 215.0 6 C315MX 985 313.0 286.0 92.5 92.0 90.0 0.84 0.80 0.72 550 225 155 60 30.00 1150
185.0 250.0 2 C315M 2940 339.0 315.0 92.0 91.0 89.0 0.90 0.86 0.78 600 140 170 40 8.71 950
185.0 250.0 4 C315M 1475 356.0 329.0 93.0 92.0 90.0 0.85 0.81 0.73 500 225 140 60 17.40 950
185.0 250.0 6 C315MX 985 362.0 334.0 92.5 92.0 90.0 0.84 0.80 0.72 550 225 155 60 30.00 1150
200.0 270.0 2 C315M 2950 367.0 336.0 92.0 91.0 89.0 0.90 0.86 0.78 600 140 170 40 8.71 950
200.0 270.0 4 C315M 1475 380.0 361.0 93.0 92.0 90.0 0.86 0.81 0.73 600 225 140 60 17.40 960
220.0 300.0 2 C315MX 2950 404.0 370.0 92.0 91.0 89.0 0.90 0.86 0.78 600 140 170 40 11.60 1150
220.0 300.0 4 C315MX 1475 423.0 387.0 93.0 92.0 90.0 0.85 0.81 0.73 500 225 140 60 22.30 1150
250.0 335.0 2 C315MX 2950 459.0 420.0 92.0 91.0 89.0 0.90 0.86 0.78 600 140 170 40 11.60 1150
250.0 335.0 4 C315MX 1475 481.0 439.0 93.0 92.0 90.0 0.85 0.81 0.73 500 225 140 60 25.00 1150
40
DRIP PROOF
SQUIRREL CAGE
MOTORS
SHIPPING SPECIFICATIONS
FOOT MOUNTED MOTORS
41
DRIP PROOF
SQUIRREL CAGE
MOTORS
+ 0.0
N9 / h9 – 0.5
GD
ED
60
G
HD
H
ØD
HA
4-HOLES Ø K BA
AA
A ± 0.5 E ± 0.5 C ±1 B ± 0.5
AB BB
1"
254 108 54 298 76 110 80 M16×32 290 390 395 22
C160L 254 159.7 298 15.0 48.002 13.957 8.91 42.3 580
C180M 241 180.0 285 15.5 55.030 16.0 10.00 49.0 593
279 121 60 337 95 110 80 335 420 445 22 1"
C180L 279 179.7 323 15.0 55.011 15.957 9.91 48.8 631
M20×40
C200M 267 200.0 318 19.5 60.030 140 110 18.0 11.0 53.0 673
1.5"
42
DRIP PROOF
SQUIRREL CAGE
MOTORS
AC
L ±5
+0.0
-0.5
N9/h9
GD
ED
F
HD
G
ØD
HA
AA BA
A ± 0.5 E±0.5 C±1 B±0.5
Y - THREADED CENTRE HOLES AB BB
Y × DEPTH
4 - HOLES Ø K
2Nos. 1.5"
225.0 19.5 65.030 19.5 65.030 58.0
C225M 356 311 149 70 426 125 427 140 110 M20X40 398 450 800 520 25
224.5 19.0 5.011 19.0 5.011 57.8
C250S 311 381 787
225.0 24.5 75.030 24.5 75.030 67.5
C250M 406 168 80 483 127 140 110 428 500 825 600 28
C250MX 349 249.5 419 24.0 75.011 24.0 75.011 67.3 927
M20X40
2Nos.-2"
C280S 368 438 918
280.0 24.5 80.030 24.5 80.030 71.0
C280M 447 190 83 540 146 170 140 551 560 969 663 35
C280MX 419 279.0 489 24.0 80.011 24.0 80.011 70.8 1071
C315S 406 315.0 482 28.5 90.035 28.5 90.035 81.0 1008
C315M 508
457 216 314.0 89 597 153 533
28.0 90.013
170 140
28.0 90.013 80.8
M24X50 630 1059 734 38
C315MX 1186
FRAME L
D E ED F TOLERANCE GD TOLERANCE G
S M L
ABOVE 200 FRAMES C225 60.030 / 60.001 140 110 18.0 / 17.957 11.0 / 10.91 53.0 / 52.8 – 800 –
MACHINES RUNNING
AT 3000 RPM HAVE C225 65.030 / 66.001 140 110 18.0 / 17.957 11.0 / 10.91 53.0 / 52.8 787 825 927
SMALLER SHAFTS
AS SHOWN HERE C280 65.030 / 66.011 140 110 18.0 / 17.957 11.0 / 10.91 58.0 / 57.8 888 939 1041
C315 70.030 / 70.011 140 110 20.0 / 19.948 12.0 / 11.91 62.5 /62.3 978 1029 1156
43
DRIP PROOF
SQUIRREL CAGE
MOTORS
AD
T LB AIR INLET
AIR OUTLET
N9 / h9 F +0.0
- 0.5
22°30°
HB
GD ED
Ø N SPIGOT
45°
ØP
G
ØD
+0 LA
PERPENDICULARITY +2
E
'Y' - THREADED CENTRE HOLES 2 - LIFTING EYEBOLTS FOR VERTICAL
Y × DEPTH MOTORS ABOVE 200 FRAMES ON LY
2 Nos.-1"
C160MD 48.018 14.00 9.00 42.5 536 213
110 80 M16×32 290 325 235
C160LD 350.5 300.016 48.002 13.957 8.91 42.3 580 235
400 19.9 5 19
C180MD 349.5 299.984 55.030 16.00 10.00 49.0 593 241.5 265
110 80 M20×40 335 352
C180LD 55.011 15.957 9.91 48.8 631 260.5
C200MD 400.5 350.018 60.030 18.00 11.00 53.0 673 266.5
450 19 5 19 140 110 398 450 298
C200LD 399.5 349.982 60.011 17.957 10.91 52.8 711 285.5
500.5 450.020 65.030 18.00 11.00 58.0
550 19 5 25 140 110 398 550 304.5 295
2 Nos.-2"
C225MD 825
499.5 449.980 65.011 17.957 10.91 57.8
M20×40
C250MD 601.0 550.022 75.030 20.00 12.00 67.5 927 342.5
660 24 6 25 140 110 428 520 355
C250MXD 599.0 549.978 75.011 19.948 11.91 67.3 969 342.5
C280MD 601.0 550.022 80.030 22.00 14.00 71.0 1071 399.5
660 24 6 25 170 140 515 794 383
C280MXD 599.0 549.978 80.011 21.948 13.91 70.8 1059 399.5
C315MD 741.0 680.025 90.035 25.00 14.00 81.0 555 810 444.5
800 24 6 28 170 140 M24×50 965 419
C315MXD 739.0 679.975 90.013 24.948 13.91 80.8 576 1186 444.5
L
FRAME D TOLERANCE E ED F TOLERANCE GD TOLERANCE G
MD MXD
C225 60.030 / 60.001 140 110 18.0 / 17.957 11.0 / 10.91 53.0 / 52.8 800 –
MACHINES RUNNING
AT 3000 RPM HAVE C250 825 927
SMALLER SHAFTS 65.030 / 65.011 140 110 18.0 / 17.957 11.0 / 10.91 58.0 / 57.8
C280 939 1041
AS SHOWN HERE
C315 70.030 / 70.011 140 110 20.0 / 19.948 12.0 / 11.91 62.5 / 62.3 1029 1156
44
DRIP PROOF
SLIPRING
MOTORS
45
DRIP PROOF
SLIPRING
MOTORS
PERFORMANCE DATA
Supply : 415 V or 380 V, 50 Hz, 3 Phase AC Voltage Variation : ± 10%
Enclosure : Screen Protected, Drip Proof (SPDP) Frequency Variation : ± 5%
Degree of Protection : IP21 for Frames upto 200,
Combined Variation : ± 10%
IP23 for Frames 225 - 315MX
Rating: Continuous, Duty: S1 Mounting : B3, Ambient : 45°C
Insulation Class : ‘F’ Temperature Rise by Resistance Method : 75°C Max.
P
OUTPUT FL FL EFFICIENCY (%) POWER FACTOR OPEN CIRCUIT ROTOR NETT
O FRAME FL GD²
AMPS AMPS ROTOR VOLTAGE CURRENT WEIGHT
L RPM 3/4 1/2 3/4 1/2 KgM²
380 V 415 V FL FL VOLTS AMPS Kg.
kW HP E FL FL FL FL
3.7 5.0 8 CW160M 700 11.0 10.0 78.0 77.0 75.0 0.68 0.64 0.56 230 9 0.51 130
5.5 7.5 6 CW160M 935 15.5 14.0 80.0 79.0 77.0 0.72 0.68 0.60 280 13 0.51 130
5.5 7.5 8 CW160L 700 15.5 14.0 80.0 79.0 77.0 0.68 0.64 0.56 235 15 0.65 150
7.5 10.0 4 CW160M 1410 17.5 16 82 81 79 0.82 0.78 0.7 375 12 0.41 130
7.5 10.0 6 CW160L 935 19.0 17.0 83.0 82.0 80.0 0.72 0.68 0.60 260 19 0.65 150
7.5 10.0 8 CW180M 705 21.0 19.0 82.0 81.0 79.0 0.68 0.64 0.56 350 13 1.14 200
9.3 12.5 4 CW160L 1420 21.0 19.0 83.0 82.0 80.0 0.82 0.78 0.70 380 16 0.53 150
9.3 12.5 6 CW180M 940 21.0 19.0 83.0 82.0 80.0 0.82 0.78 0.70 300 20 1.14 200
9.3 12.5 8 CW180L 705 26.0 24.0 82.0 81.0 79.0 0.68 0.64 0.56 345 17 1.45 220
11.0 15.0 4 CW160L 1420 24.0 22.0 84.0 82.0 80.0 0.82 0.78 0.70 390 18 0.53 150
11.0 15.0 6 CW180M 940 25.0 23.0 83.0 82.0 80.0 0.82 0.78 0.70 300 23 1.14 200
11.0 15.0 8 CW180L 705 29.5 27.0 82.0 81.0 79.0 0.70 0.66 0.58 345 20 1.45 220
15.0 20.0 4 CW180M 1420 34.0 31.0 83.0 82.0 80.0 0.82 0.78 0.70 390 23 0.53 150
15.0 20.0 6 CW180L 945 34.0 31.0 83.0 82.0 80.0 0.82 0.78 0.70 320 28 1.33 220
15.0 20.0 8 CW200M 720 38.0 35.0 84.0 83.0 81.0 0.71 0.67 0.59 300 30 2.20 275
18.5 25.0 4 CW180M 1420 39.5 36.0 84.0 83.0 81.0 0.86 0.80 0.72 435 26 0.91 200
18.5 25.0 6 CW200M 960 41.5 38.0 86.0 85.0 83.0 0.78 0.74 0.66 380 26 2.20 275
18.5 25.0 8 CW200L 720 47.0 43.0 84.0 83.0 81.0 0.72 0.68 0.60 300 38 2.20 299
22.0 30.0 4 CW180L 1420 46.0 42.0 86.0 85.0 83.0 0.84 0.80 0.72 445 29 1.16 220
22.0 30.0 6 CW200L 965 50.0 46.0 86.0 85.0 83.0 0.78 0.74 0.66 380 35 2.30 299
22.0 30.0 8 CW225M 720 53.5 49.0 86.0 85.0 83.0 0.73 0.69 0.61 350 39 3.35 380
30.0 40.0 4 CW200M 1440 62.0 57.0 87.0 86.0 84.0 0.84 0.80 0.72 415 45 1.79 275
30.0 40.0 6 CW225M 965 65.0 60.0 88.0 87.0 85.0 0.78 0.74 0.66 390 45 3.35 380
30.0 40.0 8 CW225M 720 71.0 65.0 87.0 86.0 84.0 0.74 0.70 0.62 355 51 3.35 380
37.0 50.0 4 CW200L 1440 76.5 70.0 87.0 86.0 84 0.84 0.80 0.72 465 47 2.11 299
37.0 50.0 6 CW225M 970 81.0 74.0 89.0 88.0 86 0.78 0.74 0.66 430 50 3.35 380
37.0 50.0 8 CW250S 720 86.5 79.0 89.0 88.0 86 0.74 0.70 0.62 465 50 5.70 455
45.0 60.0 4 CW225M 1450 89.5 82.0 89.0 88.0 86.0 0.85 0.81 0.73 440 60 2.66 380
45.0 60.0 6 CW250S 970 96.0 88.0 89.0 88.0 86.0 0.80 0.76 0.68 450 58 5.70 455
45.0 60.0 8 CW250M 725 104.0 95.0 89.0 88.0 86.0 0.74 0.70 0.62 480 59 6.66 525
55.0 75.0 4 CW225M 1460 111.5 102.0 89.0 88.0 86.0 0.84 0.80 0.72 440 78 2.65 380
55.0 75.0 6 CW250M 975 114.0 104.0 90.0 89.0 87.0 0.82 0.78 0.70 460 75 6.66 525
55.0 75.0 8 CW280S 730 119.0 109.0 90.0 89.0 87.0 0.78 0.74 0.66 425 79 10.65 635
75.0 100.0 4 CW250S 1460 147.5 135.0 90.5 90.0 88.0 0.84 0.80 0.72 505 88 4.77 455
75.0 100.0 6 CW280S 975 146.5 134.0 91.5 91.0 89.0 0.85 0.81 0.73 410 113 10.09 635
75.0 100.0 8 CW280M 730 163.0 149.0 90.0 89.0 87.0 0.78 0.74 0.66 536 83 13.44 750
93.0 125.0 4 CW250MX 1460 179.0 164.0 92.0 91.0 89.0 0.86 0.82 0.74 500 110 7.15 695
93.0 125.0 6 CW280M 975 180.0 165.0 92.0 91.0 89.0 0.85 0.81 0.73 520 111 13.44 750
93.0 125.0 8 CW315S 730 204.0 187.0 91.5 91.0 89.0 0.76 0.72 0.64 490 112 19.16 870
110.0 150.0 4 CW280S 1465 211.0 193.0 92.0 91.0 89.0 0.86 0.82 0.74 480 142 9.23 635
110.0 150.0 6 CW315S 975 215.0 197.0 92.5 92.0 90.0 0.84 0.80 0.72 495 140 17.50 870
110.0 150.0 8 CW315M 730 238.0 218.0 91.5 91.0 89.0 0.77 0.73 0.65 350 190 21.66 980
132.0 180.0 4 CW280M 1475 251.0 230.0 92.5 92.0 90.0 0.86 0.82 0.74 480 167 11.07 750
132.0 180.0 6 CW315M 975 258.0 236.0 92.5 92.0 90.0 0.84 0.80 0.72 450 180 20.83 980
132.0 180.0 8 CW315MX 730 280.0 256.0 92.0 91.0 89.0 0.78 0.74 0.66 490 157 26.66 1200
46
DRIP PROOF
SLIPRING
MOTORS
185.0 250.0 4 CW315M 1470 357.0 327.0 92.5 92.0 90.0 0.86 0.82 0.74 540 207 17.43 980
200.0 270.0 4 CW315MX 1475 379.0 347.0 93.0 92.0 90.0 0.86 0.82 0.74 540 224 20.91 1200
220.0 300.0 4 CW315MX 1475 417.0 382.0 93.0 92.0 90.0 0.86 0.82 0.74 540 246 20.91 1200
The above data is subject to tolerance as per the
applicable standard.
FL - Full Load, STG - Starting, C - Current,
T - Torque, DOL - Direct on Line, S/D-Star/Delta
SHIPPING SPECIFICATIONS
FOOT MOUNTED MOTORS
47
DRIP PROOF
SLIPRING
MOTORS
+ 0.0
N9 / h9 – 0.5
GD
ED
60
G
HD
H
ØD
HA
AA BA
A ± 0.5 E ± 0.5 C ±1 B ± 0.5
Y - THREADED CENTRE HOLES AB BB
Y × DEPTH
4-HOLES Ø K
CW180M 241 180.0 285 15.5 55.030 16.0 10.00 49.0 593
1"
48
DRIP PROOF
SLIPRING
MOTORS
AC
L±5
+ 0.0
– 0.5
N9 / h9
ED
GD
60
G
HD
ØD
HA
AA BA
A ± 0.5 E ± 0.5 C ±1 B ± 0.5
Y - THREADED CENTRE HOLES AB BB
Y × DEPTH
4-HOLES Ø K
2Nos. 1.5"
225.0 19.5 65.030 19.5 65.030 58.0
CW225M 356 311 149 70 426 125 427 140 110 398 450 800 520 25
224.5 19.0 65.011 19.0 5.011 57.8
CW250S 311 381 787
24.5 75.030 24.5 75.030 67.5
CW250M 406 168 225.0 80 483 127 140 110 428 500 825 600 28 2Nos.-2"
M20X40
49
SELECTION OF MOTORS
50
SELECTION OF MOTORS
DERATING FACTOR
Voltage and Frequency
0.9
Motors are available in standard voltage
ranges :
- 220/230V, or 240V, single phase and 220/ 0.8
380V, 400/695V, 380V, 380/440V, three
phase. Frequency is 50Hz or 50/60Hz or
60Hz as required. 0.7
0 1 2 3 4 5
Other voltages and frequencies can be PERCENT VOLTAGE UNBALANCE
offered to meet special requirements.
Polyphase induction motors are designed to
operate successfully with voltage variations of Polyphase Squirrel-Cage Induction Motors
± 10%. The following table shows the effects Derating Factor Due to Unbalanced Voltage
of a 10% variation on a typical induction
motor at full load. A motor should not be operated if the phase
unbalance is greater than 3%.
Voltage
Characteristics Frequency variation of up to 5% is permitted
110% 90%
for normal motor operation. However,
Slip -17% +23%
generally this should not be a problem, if
Efficiency +1% -2% the system is supplied from a utility. Motor
Power factor -3% +1% speed varies directly with the frequency of
Current -7% +11% the power supply.
Temperature °C -4° +7°
Starting torque +21% -19% Power Factor
Starting current +10% -10% Most AC motors require reactive power from
the supply system to develop magnetic fields.
The use of a motor with a nonstandard or Measured in kVAR, reactive power does not
incorrect utilization voltage from the supply provide any mechanical work.
system should be avoided. For example, a
Useful mechanical work is developed from
motor with a nameplate voltage of 380 V is
sometimes connected to a 440 V system. real power supplied by the supply system
While the maximum allowable voltage for the and is measured in kW.
motor is 418 V (110% × 380) there is no The supply distribution system provides both
allowance for an upward supply voltage Real and Reactive power to operate the
variation as the motor is already operating motor. The vector sum Real and Reactive
above its upper voltage limit. A motor of the power is called the Apparent power and is
proper voltage rating should be used, or a expressed in kVA.
−−−−−−−−−−−−−−−−−−−−−−−
transformer installed to supply the correct Apparent Power = √ Real Power² + Reactive Power²
voltage.
The ratio of Real power to Apparent power is
Phase unbalance must be less than 1% for defined as the Power Factor.
proper motor operation. A phase unbalance of
Real Power
3.5% results in a temperature rise of 25% and Power Factor =
a current increase of 6-10 times the voltage Apparent Power
unbalanced. These effects are due to If the load consumes Reactive power from the
negative sequence currents flowing in the system, the power factor is said to be lagging.
rotor. Most electrical devices operate at a lagging
Voltage unbalance % is calculated as follows : power factor.
Maximum Deviation from Average The power factor of induction motors varies
V = × 100 with load.
unbalance V Average
The combined kW demand of all devices
As an example, if line voltages were supplied by the distribution systems divided
measured as 600, 585 and 609 volts, the by the combined kVA demand of all supplied
average is 598 volts. The maximum deviation devices yields the plant power factor.
from average is 13 volts (598-585), and thus
the voltage unbalance is (13/598)×100 = 2.1%
If a motor must be operated with a phase
51
SELECTION OF MOTORS
7.0
Penalties are usually charged by utilities if
plant power factor is below 90%, in which 6.0
case, correction such as capacitors should be POINT A
applied. 5.0
% VOLTAGE DIP
OBJECTIONABLE RANGE
5.0
OBJECTIONABLE RANGE of the voltage on the 120 V lighting circuit and
4.0
Thershold
causes a noticeable flicker.
of Objection
3.0
If the motor is started once every hour then
the point on the flicker curve is in the
2.0
NOT
objectionable range (point A).
OBJECTIONABL To correct this problem, the lighting circuits
1.5 Thershold E
1.0 of Perception can be supplied from a separate feeder, or
0 the voltage drop along the feeder can be
0 8 12 1 2 5 10 20 30 1 5 10 20 30 1 2 5 10 20 30
PER DAY PER HR. PER MIN. PER SEC. reduced. In this case, a drop of 3.6% or less
FREQUENCY OF VOLTAGE FLUCTU ATION
is not objectionable.
OR NUMBER OF STARTS
Supplying the lighting from a different feeder
or upgrading the feeder is one approach often
Voltage Flicker Curve
used.
If the magnitude of voltage drop and the A reduced voltage starter for the motor is
frequency of occurrence lie below the another alternative and often a very cost-
threshold of objection, but above the effective solution.
threshold of perception, people notice the light If the starting current is limited to 70% of its
flicker, but generally do not find it irritating. normal value by use of a reduced voltage
If the magnitude of the voltage drop and the starter, the voltage dip is 3.5% (70% × 5%)
frequency of occurrence lie below the and motor starting of once per hour is not
threshold of perception, people don't generally objectionable (point B).
notice any flicker.
PHYSICAL AND ENVIRONMENTAL
As an example, consider a 5 HP motor
supplied by a 208 V feeder which also CONSIDERATIONS
supplies 120 V lighting circuits.
Assume: 5 HP motor Usual Service Conditions
Full load amps = 16 A Motor ratings apply to motors operating under
Starting current = 96 A usual service conditions.
Feeder impedance = 0.06Ω The International Standards specify usual
Voltage drop along feeder environmental conditions as :
= starting current × feeder impedance
1. Exposure to an ambient temperature in the
= 96 × 0.06
range of 0°c to 40°C or when water cooling
= 6V
is used, in the range of 10°C to 40°C.
2. Exposure to an altitude which does not
exceed 3300 feet (1000 metres).
3. Installation on a rigid mounting surface.
4. Installation in areas or supplementary
enclosures which do not seriously interfere
with the ventilation of the machine.
52
SELECTION OF MOTORS
53
SELECTION OF MOTORS
100,000
90,000
80,000
70,000
60,000
50,000
40,000
30,000 Average
INSULATION LIFE (HOURS)
Insulation Life
20,000
105° 130° 155° 180°
10,000
9,000
8,000
7,000
6,000
5,000
4,000
Class A Class F
3,000
Class B Class H
2,000
1,000
0 50 100 150 200 250 300
WINDING TEMPERATURE IN °C
Noise 9
8 Rate = 6¢/kwh
If a motor is used in an area where noise 7
levels are of concern, it should use 5¢/kwh
6
bearings which are quieter than roller or ball 4¢/kwh
5
bearings.
4
Quiet motors equipped with these bearings 3
and specially designed ventillation systems 2
can often be offered 1
Other Modifications 0
The standard motors suit almost all 0 2000 4000 6000 8000
applications. These are less expensive, have
proven engineering and are available on Annual operating Costs of a 20 HP Motor
shorter lead times. However, motors can be Because the operating cost over the life
ordered with an almost unlimited number of of a motor is often many times its purchase
variations to fit special applications where a price, small differences in motor efficiency can
standard motor is not suitable. We can yield significant savings.
provide specific information on availability,
Motor Efficiency
lead time and price.
The efficiency of a motor is the ratio of
mechanical power output to the electrical
power input and is usually expressed as a
percentage.
54
SELECTION OF MOTORS
EFFICIENCY %
60
10
Electrical 0
0 25 50 75 100 125
Power In
% RATED LOAD
100%
Mechanical
Power Out 80%
%
POWER 60%
FACTOR
40%
0
Core losses are comprised of hysteresis
losses (the energy required to magnetize the 0 25% 50% 75% 100%
Product improvement is a continuous process. Hence, data given in this catalogue is subject to change without intimation.
55
The widest Range of Motors, Alternators and Pumps
from Crompton Greaves
Single Phase / Three Phase FHP Motors Standard Re-Rolling Mill Duty motors and Special
(FHP Range) Dual Speed Induction Generators for Wind Mill Duty
From 90 watts to 2.25kW to BS 5000 part11 are offered.
Series 40 and Series 50 Frames Three Phase, HT, Induction and Synchronous
Machines (Large Machines Range)
DP, TEFC and TE(AOM) enclosures
Upto 6000 kW, SCR and SR. (Range being
General Purpose and Customer Specific
extended upto 8 MW)
For 120 Volts or 240 Volts, 50/60Hz. supply
Upto 20 poles.
suitability
CACA, TETV, SPDP, CACW, Flame proof, Type 'e',
CSA NRTL/C Listed for Canada and USA and with
Type 'n', Type 'p' enclosures.
CE mark for Europe
For 2.2kV, 3.3kV, 6.6kV, 11kV, 14.3kV, 50/60 Hz
Standard Three Phase, LT, Induction Motors
supply.
(M1 and M3 Range)
"Resin-Rich" alternatively "Resin-Poor" HIPACT-
From 0.18kW to 250kW, SCR and SR to IEC 325.
Hitachi Insulation offered.
Frames 63 to 355L.
S1 to S8 duty cycles for all applications.
DP, TEFC, TE, Flame proof (Type 'd'). Increased
Alternators
Safety (Type 'e'), Non-sparking (Type 'n'),
Pressurised (Type 'p') enclosures etc. From 5 KVA to 250 KVA, to generate 240 Volts,
0.8PF, 50/60 Hz, single phase and 415 Volts, 0.8PF,
For 110 to 660 volts, 50/60Hz supply.
50/60Hz, three phase, AC supply at 1500/1800 rpm,
Under CSA NRTL/C listing for Canada and USA
conforming to BS5000 (Part 99).
and with CE mark for Europe.
Brush and Brushless designs, revolving armature
S1 to S8 Duty Cycles for all applications.
and revolving field types, with self exited and self
Three Phase, LT, Induction Motors regulated exiter units.
(Large Machines Range)
For general purpose, marine and pully drive
From 150kW upto 1000kW, SCR and SR. applications.
Frames 315 to 710, 2 pole to 14 pole. Pumps
TEFC, DP, Type 'd', Type 'e', Type 'n', Type 'p' For Water Circulation Applications.
enclosures.
For single phase, and three phase supply.
Vertical and horizontal, foot cum flange mounting.
With 250 Watts to 80 kW motors.
For 400 to 690 volts, 50/60 Hz supply.
Coupled, monoblocks, Submersibles, Jet
S1 to S8 Duty Cycles for all applications. Centrifugals, In Line Pumps for Industrial,
Agricultural and Commercial applications.
56