Beruflich Dokumente
Kultur Dokumente
www.isotemp.com www.taitien.com
REV. -
DESCRIPTION OF REVISION
DWN. BY
APV. BY
DATE 03-24-2010
JX
TST
1. OUTPUT(PIN = "R.F. OUTPUT") 1.1. Frequency 1.2. Initial Accuracy a. @ Temperature b. After time on power c. Within time period following date code d. @ VCO Input voltage 1.3. Waveform 1.4. Level a. "1" level b. "0" level 1.5. Load 1.6. Duty cycle 1.7. Spurious 2. FREQUENCY STABILITY 2.1. Ambient
Stability Temperature
10.000000 MHz < 1x10-6 +25 1C 30 5 minutes 90 days +2.5 0.001 V Rectangular HCMOS > +3.5 V < +0.5 V 15 pF 45% to 55%@ +2.0 V < -60 dBc
< 3x10-8
< 5x10-8
< 1x10-7
< 2x10-7
OCXO147-1000 OCXO147-1001 OCXO147-1002 OCXO147-1003 OCXO147-1004 OCXO147-1005 OCXO147-1006 OCXO147-1007 Model Number < 5x10-9/day < 5x10-9 after 30 days < 5x10-7 < 3x10-6 < 5x10-8/5% change < 1x10-10/1 second root Allan variance < 1x10-7 in 2 minutes @ +25 1C (referenced to 1 hour) < < < < -100 -130 -145 -150 dBc dBc dBc dBc
PAGE OF TOTAL
2.2. Aging a. At time of shipment b. After indefinite storage i. Daily ii. Yearly iii. 10 years 2.3. Voltage 2.4. Short term 2.5. Warm-up 2.6. Phase Noise a. @ 10 Hz b. @ 100 Hz c. @ 1 kHz d. @ 10 kHz
OUR PERFORMANCE YOUR REPUTATION
REV. -
3. ELECTRICAL FREQUENCY ADJUSTMENT (PIN = "VCO INPUT") 3.1. Range > 5x10-6 Referenced to frequency at nominal Center Voltage 3.2. Control 0 to +5 V 3.3. Slope Positive 3.4. Center Voltage +2.5 V 3.5. Linearity < 10% 3.6. Input impedance > 50 k 4. INPUT 4.1. 4.2. 4.3. POWER (PIN = "+VDC") Voltage Current Steady state
5. ENVIRONMENTAL 5.1. Storage temperature 5.2. Vibration (non-operating) 5.3. Shock (non-operating)
-40C to +85C MIL-STD-202, Method 201 (0.06" Total p-p, 10 to 55 Hz) MIL-STD-202, Method 213, Test Condition J (30 g, 11 ms half-sine)
6. RoHS All units supplied under this MODEL NUMBER are RoHS compliant. 7. MECHANICAL(Outline drawing) 7.1. Applicable series 7.2. Model number 7.3. Outline drawing
PAGE OF TOTAL
REV. -
PIN CONNECTIONS
PIN FUNCTION VCO INPUT
or
MARKING THIS SURFACE Square corner designates PIN 1. (VIEW FROM TOP)
1
(See Note 1)
7 8 14
Notes: 1.If the specification does not specify parameters for PIN 1 then PIN 1 is not internally CONNECTED. 2.If the specification does not specify parameters for "MECHANICAL FREQUENCY ADJUSTMENT" then there is no Trim Access.
MARKING
0.03 0.76
0.80 20.3 0.600 15.24 CENT. 1 7 0.300 CENT. 0.50 7.62 12.7 14 8
Number for reference only. (Not stamped on unit) (VIEW FROM BOTTOM)
OSCILLATORS
REV: B SHT: 1 OF 1
DWG: 125-630
Charlottesville, Virgina USA CODE I.D. NO. SCALE: 2:1 DWN. BY: BTG
03-05-2008 03-09-2010
31785
BTG BTG JRD TST
UNLESS OTHERWISE SPECIFIED: ANGES: 1 DEGREE FRACTIONS: 1/32 INCH DECIMALS: .XX .015, .XXX .010 INCH
MATERIAL: STEEL LET REVISION BY APP DATE FINISH: NICKEL MARK: LABEL