Beruflich Dokumente
Kultur Dokumente
1Battery Pack 2BOTTOM DOOR ASSY 3THERMAL-KITCPU And VGA Card Module 4RAMWLAN Module 5HDD Module ASSY 6ODD Module ASSY 7HINGE COVER ASSY 8UP CASE ASSY 9LOWER CASE ASSY 10LCD MODULE ASSY
EX630MS-1671Disassemble SOP
1Battery Pack
1-2Push the battery Release button as below, then slide the battery pack out of the slot;
NO. 1
Qty 1
EX630MS-1671Disassemble SOP
2BOTTOM DOOR ASSY
2-1Remove 4pcs M2.5*5mm screws; NoteScrew driver torque is 2.5-3.0kgf.cm
NO. 1 2
Qty 4 1
EX630MS-1671Disassemble SOP
3THERMAL-KITCPU And VGA Card Module
3-1Remove 3pcs M2.5*5mm screws and 4pcs Spring screws , disconnect CPU Fan sink Cable. NoteScrew driver torque is 1.8-2.0kgf.cm
5
1
NO. 1 2
Qty 3 1
EX630MS-1671Disassemble SOP
3-3 Open the CPU Socket as below;
NO. 1
Qty 1
EX630MS-1671Disassemble SOP
3-5Remove 1pcs M2.5*5mm screw; NoteScrew driver torque is 2.5-3.0kgf.cm
NO. 1 2
Qty 1 1
EX630MS-1671Disassemble SOP
4RAMWLAN Module
4-1Push RAM Slot Fastener as below;
NO. 1
Qty 2
EX630MS-1671Disassemble SOP
4-3Remove WLAN Antenna, then remove 1pcs M2*3mm screw ; NoteScrew driver torque is 1.82.0kgf.cm
NO. 1 2
Qty 1 1
EX630MS-1671Disassemble SOP
5HDD Module ASSY
5-1Remove HDD Module as below;
EX630MS-1671Disassemble SOP
5-2Remove 2pcs M3*3.5mm screws, then remove HDD Bracket as below; NoteScrew driver torque is 2.0~2.5kgf.cm
NO. 1 2 3
Qty 2 1 1
EX630MS-1671Disassemble SOP
6ODD Module ASSY
6-1Remove 1pcs M2.5*5mm screw, then remove ODD Module Assy as below; NoteScrew driver torque is 2.5-3.0 kgf.cm
NO. 1
Qty 1
EX630MS-1671Disassemble SOP
6-2Remove ODD Bezel as below;
NO. 1
Qty 1
EX630MS-1671Disassemble SOP
6-3Remove 2pcs M2*3mm screws, then remove ODD Braket as below; NoteScrew driver torque is 1.5~1.8kgf.cm
NO. 1 2 3
Qty 2 1 1
EX630MS-1671Disassemble SOP
7HINGE COVER ASSY
7-1Push Fastener as below;
EX630MS-1671Disassemble SOP
7-2Remove Hinge Cover as below;
NO. 1
Qty 1
EX630MS-1671Disassemble SOP
7-3Remove Sensor Board as below;
NO. 1
Qty 1
EX630MS-1671Disassemble SOP
7-4Remove LCD LVDS Cable, MIC and CAMERA Cable as below;
NO. 1 2
Qty 1 1
EX630MS-1671Disassemble SOP
7-5Pull cable out the slot as below;
EX630MS-1671Disassemble SOP
7-6Remove 4pcs M2.5*5mm screws as below; NoteScrew driver torque is 2.5-3.0kgf.cm
NO. 1
Qty 4
EX630MS-1671Disassemble SOP
7-7Remove LCD MODULE ASSY as below;
EX630MS-1671Disassemble SOP
8UPCASE ASSY
8-1Remove 3pcs M2*3mm screws, then remove Keyboard as below; NoteScrew driver torque is 1.8-2.0kgf.cm
NO. 1 2
Qty 3 1
EX630MS-1671Disassemble SOP
8-2Remove PCI-E and XD dummy Card as below;
NO. 1 2
Qty 1 1
EX630MS-1671Disassemble SOP
8-3Remove Power Board ,Sensor Board, Touchpad, Finger printer, AUDIO board , Bluetooth CABLE as below;
NO. 1
Qty 1
EX630MS-1671Disassemble SOP
8-4Remove 14pcs M2.5*5mm screws; NoteScrew driver torque is 2.5-3.0kgf.cm
NO. 1
Qty 14
EX630MS-1671Disassemble SOP
8-5Disconnect UP CASE and LOWER CASE as below;
EX630MS-1671Disassemble SOP
8-6Disconnect M/B and Up case as below;
NO. 1 2
Qty 1 1
EX630MS-1671Disassemble SOP
8-7Remove 2pcs M2*3mm screws as below; NoteScrew driver torque is 1.5~2.0kgf.cm
NO. 1 2 3
Qty 2 1 1
EX630MS-1671Disassemble SOP
8-9 Remove Bluetooth CABLE as below;
NO. 1 2 3
Qty 1 1 1
EX630MS-1671Disassemble SOP
8-11Remove 3pcs M2*3mm screws as below; NoteScrew driver torque is 1.5~1.8kgf.cm
NO. 1 2
Qty 3 1
EX630MS-1671Disassemble SOP
8-13Remove 1pcs M2*3mm screw , then remove Touchpad FFC (To M/B) as below; NoteScrew driver torque is 1.5~1.8kgf.cm
NO. 1 2 3
Qty 1 1 1
EX630MS-1671Disassemble SOP
8-14Remove Finger Printer , then remove FFC (To M/B) as below;
NO. 1 2
Qty 1 1
EX630MS-1671Disassemble SOP
8-15Remove Touchpad Module as below;
NO. 1 2
Qty 1 1
EX630MS-1671Disassemble SOP
9LOWER CASE ASSY
NoteScrew driver torque is 2.0~2.5kgf.cm
NO. 1 2
Qty 2 1
EX630MS-1671Disassemble SOP
9-2Remove 2pcs M2*3mm screws as below; NoteScrew driver torque is 1.5~2.0kgf.cm
NO. 1 2 3
Qty 2 1 1
EX630MS-1671Disassemble SOP
9-4Remove Audio Cable(TO MB) and SPEAKER Cable as below;
NO. 1 2
Qty 1 1
EX630MS-1671Disassemble SOP
9-5Remove 2pcs M2.5*5mm screws, then remove SPEAKER ,RJ11,TV IO JACK as below; NoteScrew driver torque is 2.0~2.5kgf.cm
NO. 1 2 3 4 5
Qty 2 1 1 1 1
EX630MS-1671Disassemble SOP
10LCD MODULE ASSY
10-1Remove 8pcs LCD Rubbers, then remove 4pcs M2.5*5mm screws; NoteScrew driver torque is 2.5-3.0kgf.cm
NO. 1 2
Qty 8 4
EX630MS-1671Disassemble SOP
10-2Remove LCD Bezel as below;
NO. 1
Qty 1
EX630MS-1671Disassemble SOP
10-3Remove 3pcs magnets as below;
NO. 1 2
Qty 2 1
EX630MS-1671Disassemble SOP
10-4Remove 4pcs M2.5*5mm screws, then remove Left And Right Hinge; NoteScrew driver torque is 2.5-3.0kgf.cm
NO. 1 2 3
Qty 4 1 1
EX630MS-1671Disassemble SOP
10-5Remove Inverter Module, then remove Display Module;
NO. 1
Qty 1
EX630MS-1671Disassemble SOP
10-6Remove CMOS Camera Module as below;
Qty 1 1
EX630MS-1671Disassemble SOP
10-7Remove MIC Module as below;
Qty 1
EX630MS-1671Disassemble SOP
10-8Remove 2pcs WLAN Antenna as below;
NO. 1 2 3
Qty 1 1 1
EX630MS-1671Disassemble SOP
10-9Remove Coaxial Cable as below;
NO. 1 2
Qty 1 1
EX630MS-1671Disassemble SOP
10-10Remove 8pcs M2*3mm screws, then remove LCD Bracket as below; NoteScrew driver torque is 1.5~2.0kgf.cm
NO. 1 2 3
Qty 8 1 1
Photo
Label
(M2*L3MM)white
(M2.5*L4MM) black
(M3*L3.5MM) white
Photo
label
2 7
Photo
Screw specification
label
(M2.5*L5MM) black
Photo
Screw specification
label
(M3*L3.5MM) white
(M2.5*L5MM) black
(M2*L3MM)white
Photo
Screw specification
Label
(M2*L3MM)white
(M2.5*L5MM) black
Photo
label
Photo
Screw specification
label
(M2*L3MM)white
(M2.5*L5MM) black
Photo
Screw specification
label
(M2.5*L5MM) black
(M2*L3MM)white
Photo
Screw specification
label
(M2.5*L4MM) black
(M2.5*L5MM) black
(M2*L3MM) white
Photo
Screw specification
label
(M2*L3MM)white