Beruflich Dokumente
Kultur Dokumente
Description
The STR-W6200D series are current-mode PWM ICs that incorporate controller chips. These devices are manufactured using a proprietary high-voltage BCD process, and avalancheguaranteed MOSFETs. These elements allow power supply systems designs that are highly reliable and simple, with fewer peripheral components. These ICs also provide Auto-Burst mode operation, which lowers input power requirements at light loads, and improves efficiency over the entire load range and universal-input range. Applicatons include: TV set top box LCD PC monitor, LCD TV Printer, scanner General consumer, PC, and industrial applications requiring SMPS power supply with standby mode
Package: TO-220
Not to scale
STARTUP UVLO
15.5 V/ 8.9 V 7.1 V
D/ST
REG
VREG
28.5 V
RST
R SQ
=1.6 mA
I startup
DMAX 75%
RQ S DRV
PWM OSC
SQ R
S2
FM/ELP
Frequency Modulation
12 V 7.8 V
OLP
CK S1 tOLP = tFM 32 R
OCP
160 A
FB Slope Compensation
Feedback Control
LEB
S/OCP
GND
28103.52
STR-W6252D
Features and Benefits (continued) Bias Assist function improves start-up performance by selfbiasing the VCC pin, and allows a use of a small value VCC capacitor, resulting in improved response to overvoltage conditions Very low current consumption in nonoperating (UVLO) state: ICC(off) = 5 A (typical) at VCC = 13.8 V Slope compensation circuit stabilizes operation, preventing interference from subharmonics Leading Edge Blanking Various protections: Overcurrent Protection (OCP), pulse-by-pulse sensing Overload Protection (OLP), auto restart after certain duration External Latch Protection (ELP), latched Overvoltage Protection (OVP), latched Thermal Shut Down (TSD), latched Externally-activated shut down protection (ELP) for emergency system shut down Auto-Burst Standby function (pin < 0.1 W at zero output load condition) Audible noise reducing function in Standby mode TO-220 full-molded package with 6 pins
Selection Guide
Part Number
STRW6252D
Packing
50 pieces per tube
Pin-out Diagram
1 2 3 4 5 6 7
All performance characteristics given are typical values for circuit or system baseline design only and are at the nominal operating voltage and an ambient temperature, TA, of 25C, unless otherwise stated.
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
STR-W6252D
ABSOLUTE MAXIMUM RATINGS at TA = 25C Characteristic Drain Current1 Maximum Switching Current2 Single Pulse Avalanche Energy3 S/OCP Terminal Voltage FM/ELP Terminal Voltage FM/ELP Terminal Inflow Current FB Terminal Voltage Controller (MIC) Input Voltage MOSFET Power Dissipation4 Controller (MIC) Power Dissipation Operating Internal Frame Temperature Operating Ambient Temperature Storage Temperature Channel Junction Temperature
1Refer
Symbol IDpeak IDMAX EAS IDpeak VOCP VFM IFM VFB VCC PD1 PD2 TF Top Tstg TJ
Terminal 1-3 1-3 1-3 1-3 3-5 7-5 7-5 6-5 4-5 8-1 5-3 With infinite heatsink Without heatsink For VccIcc Refer to TOP Single Pulse TA = 20 to 125C Single Pulse
Note
Rating 3.2 3.2 62 2.3 6 to 6 0.3 to 12 3 0.3 to 9 0 to 32 26 1.3 0.8 20 to 115 20 to 115 40 to 125 150
Unit A A mJ A V V mA V V W W W C C C C
VDD = 99 V, L = 20 mH
to figure 1 2I DMAX is the drain current on the D/ST pin determined by the drive voltage of the IC and the threshold voltage, Vth, of the MOSFET 3Refer to figure 3 4Refer to figure 4
10.00
0. 1 m s
60
1.00
40
it
s 1m
0.10 20 Refer to figure 1 for MOSFET SOA temperature derating coefficient 0 0 25 50 75 100 125 150 Temperature, TF (C) 0.01 1 10 100 1000
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
STR-W6252D
80
1.00
60
40
0.10
20
0.01
10
1m
10m
100m
20
15
10
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
STR-W6252D
Symbol Terminal
Test Conditions
Min.
Typ.
Max
Units
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
STR-W6252D
ELECTRICAL CHARACTERISTICS, continued, valid at VCC = 18 V, TA = 25C, unless otherwise specified Characteristic
Protection Operation OCP Threshold Voltage at Zero Duty Cycle (0% On-Duty) Drain Peak Current Compensation Coefficient OCP Threshold Voltage After Compensation Leading Edge Blanking Time OLP Delay Time Circuit Current in OLP-Operation VOCP1 DPC VOCP2 tblank tOLP ICC (OLP) 3-5 3-5 1-5 1-5 4-5 Set VFM = 0 V and increase VOCP. (VOCP1 is the S/OCP terminal voltage level at which D/ST changes from low to high) Measurement circuit 5 DPC = 0.75 SLP / fOSC(av) VOCP2 = DPC DMAX + VOCP1 (The low portion of the D/ST terminal waveform at VOCP = 2 V) Measurement circuit 5 (Time between setting FB terminal open and when oscillation stops) Measurement circuit 6 (Inflow current into VCC terminal after OLP operation) Measurement circuit 6 (VCC terminal voltage at which the voltage of D/ST terminal is switched from low to high by decreasing VFB after setting VFM = 0 V) Measurement circuit 1, VCC = 18.0 V through 27 to 30 V (Inflow current into VCC terminal after OVP operation) Measurement circuit 1, VCC = 7.8 V (VCC voltage at which ICC is dropped below 20 A by decreasing VCC after OVP operation) VCC = 31.0 V through 7.8 to 6.4 V (FM/ELP terminal voltage at which the oscillation of the D/ST terminal waveform is stopped by increasing VFM) Measurement circuit 2 (Inflow current at VFM = VELP) Measurement circuit 2 0.71 1.5 0.82 280 0.78 1.9 0.93 400 200 410 0.86 2.3 1.04 520 700 V mV/ DC% V ns ms A
Symbol Terminal
Test Conditions
Min.
Typ.
Max
Units
VCC(OVP)
4-5
27
28.5
30
ICC(La.H) VCC(La.OFF)
4-5 4-5
6.4
140 7.1
220 7.8
A V
ELP Threshold Voltage Inflow Current at External Latch Protection Thermal Shut Down Operating Temperature Power MOSFET Characteristics Drain-to-Source Breakdown Voltage Drain Leakage Current ON-Resistance Switching Time Thermal Resistance Single Pulse Avalanche Energy
1Input 2The
7-5 7-5
6.4 135
7.1 55
7.8 100
V A C
ID = 300 A, Measurement circuit 8 VD = 650 V, Measurement circuit 7 ID = 1.0 A, VFM = 0 V Measurement circuit 10 Measurement circuit 9 Measured between junction and internal frame Measurement circuit 11
650
V A ns C/W
and output current polarity at the device pin; plus(+) represents sink and minus() represents source. latch circuit means a circuit operated ELP, OVP, and TSD.
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
STR-W6252D
Measurement Circuit 1
V CC(OVP) 32V
STR-W6200D
D/ST
1
V CC(ON) 13.8V
FB FM/ ELP
7
18V
V CC V FM V FB 0V 0V
5V
8V
V CCc(La.OFF)
1F V FB V FM
VD
Measurement Circuit 2
18V V CC V FB 0V V FMH V FM 4.5Vtyp V FML 2.8Vtyp Isrc(FM) Isnk(FM) t2 5V 0V V ELP V LFM +(V FMH -V FML)/2 IELP
f =f osc(Hi)-f osc(Lo) Dmax= t2/ t1100
5V
STR-W6200D
D/ST
1
FB
FM/ ELP
7
IFM A
IFM 0A
1F V FB V FM VD
f osc(Hi)
f osc(Lo)
f osc(av) t1
Measurement Circuit 3
18V V CC 5V V FM 0V 2V V FB Vburst 0V
STR-W6200D
D/ST
1
FB
FM/ ELP
7
IFB A V FM V FB VD
1F
IFB IFB(MAX)
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
STR-W6252D
Measurement Circuit 4
18V V CC V FM 5V
STR-W6200D
D/ST
1
FB
FM/ ELP
7
V FB
VD 100
V OCP
+
V FB 4V
V FM
V OCP
18V V DD 10V V CC
1F
Measurement Circuit 5
18V V CC 5V 3.65V 2V V OCP1 V OCP 0V tblank V FM VD V D(Lo)
STR-W6200D
D/ST
1
V FM
FB FM/ ELP
7
0V
VD 100
V OCP
+
18V V DD 20V V CC
1F
Measurement Circuit 6
18 V V CC
STR-W6200D
D/ST
1
FB
FM/ ELP
7
V FM SW ON OFF V FB
t FM 7.8 V typ
VD 100 V DD 10V
ICC A
+
V FB SW V FM 47nF
1F V CC 18V
ICC
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
STR-W6252D
Measurement Circuit 7
400V V DD 18V V BIAS 650V
STR-W6200D
D/ST
1
FB
FM/ ELP
7
V CC V FM
0V 0V
13V 5V
ID A
ICC
A ID
+
V DD
V CC
V FM
1F
Measurement Circuit 8
Measurement Circuit 9
STR-W6200D
D/ST
1
FB
FM/ ELP
7
STR-W6200D
D/ST S/OCP
1 3 4
VCC GND
5 6
FB
FM/ ELP
7
VD
10V 90%
VD V ID 300 A 18V V CC
+
V FM 47nF tr
10%
1F
1F
Measurement Circuit 10
18V
STR-W6200D
D/ST
1
V CC
FB FM/ ELP
7
5V V FM 0V
VD V ID 0.6A
+
18V V CC
1F
V FM
VD
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
STR-W6252D
Measurement Circuit 11
Vcc
18V
STR-W6200D
D/ST S/OCP VCC GND
4 5 6
FB
FM/ ELP
7
V GS
8V
L V DD
V DSpeak IL V DS V DD
V DS 18V V GS V CC
1F
V IN ( ac)
O UT
1 D/ST
4 VCC
S T R -W 6200D
FM / S/O C P ELP 3 7 GND 5 FB 6
G ND
Option
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
10
STR-W6252D
7.9 0.2
16.9 0.3
1.34 0.1
+0.2
(5.4)
1.74 0.1
+0.2
0.45 0.1
+0.2
1 2 3 4 5 6 7
Gate burr: 0.3 mm (max.) Terminal core material: Cu Terminal treatment: Ni plating and solder dip Heat sink material: Cu Heat sink treatment: Ni plating Leadform: 2003 Weight (approximate): 2.3 g Dimensions in millimeters
Drawing for reference only Branding codes (exact appearance at manufacturer discretion): 1st line, type: W6252 2nd line, lot: YMDD R Where: Y is the last digit of the year of manufacture M is the month (1 to 9, O, N, D) DD is the 2-digit date R is the manufacturer registration symbol
Leadframe plating Pb-free. Device composition complies with the RoHS directive.
10.4 0.5
3.2 0.2
Gate Burr
4 0.2
10.0 0.2
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
R (2 1)
11
STR-W6252D
4.8
+0.4 0
1.4
Shipping Tube Dimensions: Wall thickness: 0.60.3 mm Wall warp: <2 mm Material: Hardened polyvinyl Coating: antistatic Tolerance 0.4 mm, unless otherwise specified
2.85 (3.6) 14.3
35.0
Spacer
Shipping Carton Dimensions: Capacity: 1800 pieces maximum per carton 36 tubes per carton 3 rows, 12 tubes per row
Tube
Spacer
620
125
Tube
All dimensions: mm
185
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
12
STR-W6252D
WARNING These devices are designed to be operated at lethal voltages and energy levels. Circuit designs that embody these components must conform with applicable safety requirements. Precautions must be taken to prevent accidental contact with power-line potentials. Do not connect grounded test equipment. The use of an isolation transformer is recommended during circuit development and breadboarding.
Because reliability can be affected adversely by improper storage environments and handling methods, please observe the following cautions. Cautions for Storage Ensure that storage conditions comply with the standard temperature (5C to 35C) and the standard relative humidity (around 40 to 75%); avoid storage locations that experience extreme changes in temperature or humidity. Avoid locations where dust or harmful gases are present and avoid direct sunlight. Reinspect for rust in leads and solderability of products that have been stored for a long time. Cautions for Testing and Handling When tests are carried out during inspection testing and other standard test periods, protect the products from power surges from the testing device, shorts between adjacent products, and shorts to the heatsink. Remarks About Using Silicone Grease with a Heatsink When silicone grease is used in mounting this product on a heatsink, it shall be applied evenly and thinly. If more silicone grease than required is applied, it may produce stress. Volatile-type silicone greases may produce cracks after long periods of time, resulting in reduced heat radiation effect. Silicone grease with low consistency (hard grease) may cause cracks in the mold resin when screwing the product to a heatsink. Our recommended silicone greases for heat radiation purposes, which will not cause any adverse effect on the product life, are indicated below: Type G746 YG6260 Suppliers Shin-Etsu Chemical Co., Ltd. Toshiba Silicone Co., Ltd.
SC102 Dow Corning Toray Silicone Co., Ltd. Soldering When soldering the products, please be sure to minimize the working time, within the following limits: 2605C 10 s 3505C 3 s Soldering iron should be at a distance of at least 1.5 mm from the body of the products Electrostatic Discharge When handling the products, operator must be grounded. Grounded wrist straps worn should have at least 1 M of resistance to ground to prevent shock hazard. Workbenches where the products are handled should be grounded and be provided with conductive table and floor mats. When using measuring equipment such as a curve tracer, the equipment should be grounded. When soldering the products, the head of soldering irons or the solder bath must be grounded in other to prevent leak voltages generated by them from being applied to the products. The products should always be stored and transported in our shipping containers or conductive containers, or be wrapped in aluminum foil. Assembly During soldering or other operations, the interior frame temperature of the device should never exceed 105C. Recommended screw torque through the mounting tab is 0,588 to 0.785 N m (6 to 8 kgf cm)
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
13
STR-W6252D
The products described herein are manufactured in Japan by Sanken Electric Co., Ltd. for sale by Allegro MicroSystems, Inc. Sanken and Allegro reserve the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Therefore, the user is cautioned to verify that the information in this publication is current before placing any order. When using the products described herein, the applicability and suitability of such products for the intended purpose shall be reviewed at the users responsibility. Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to society due to device failure or malfunction. Sanken products listed in this publication are designed and intended for use as components in general-purpose electronic equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). Their use in any application requiring radiation hardness assurance (e.g., aerospace equipment) is not supported. When considering the use of Sanken products in applications where higher reliability is required (transportation equipment and its control systems or equipment, fire- or burglar-alarm systems, various safety devices, etc.), contact a company sales representative to discuss and obtain written confirmation of your specifications. The use of Sanken products without the written consent of Sanken in applications where extremely high reliability is required (aerospace equipment, nuclear power-control stations, life-support systems, etc.) is strictly prohibited. The information included herein is believed to be accurate and reliable. Application and operation examples described in this publication are given for reference only and Sanken and Allegro assume no responsibility for any infringement of industrial property rights, intellectual property rights, or any other rights of Sanken or Allegro or any third party that may result from its use. Copyright 2006-2007 Allegro MicroSystems, Inc. This datasheet is based on Sanken datasheet SSE23677
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
14
STR-W6252D
Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
15