Beruflich Dokumente
Kultur Dokumente
purposes
Australian Standard™
Australian Standard™
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
Originated as AS 4181—1994.
Second edition 1999.
COPYRIGHT
© Standards Australia International
All rights are reserved. No part of this work may be reproduced or copied in any form or by any
means, electronic or mechanical, including photocopying, without the written permission of the
publisher.
Published by Standards Australia International Ltd
PO Box 1055, Strathfield, NSW 2135, Australia
ISBN 0 7337 2649 6
AS 4181—1999 2
PREFACE
This Standard was prepared by the Joint Standards Australia/Standards New Zealand
Committee WS/16, Cast Iron Pressure Pipes and Fittings, to supersede AS 4181—1994.
This Standard is the result of a consensus among Australia/New Zealand representatives on
the Committee to produce it as an Australian Standard.
The objective of this Standard is to include design, materials and type tests required for
stainless steel clamps.
This edition includes modification to materials and fabrication requirements and an
additional appendix to demonstrate means for demonstrating compliance with this Standard.
The terms ‘normative’ and ‘informative’ have been used in this Standard to define the
application of the appendix to which they apply. A ‘normative’ appendix is an integral part
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
CONTENTS
Page
1 SCOPE...................................................................................................................................4
2 APPLICATION......................................................................................................................4
3 REFERENCED DOCUMENTS.............................................................................................4
4 DEFINITIONS.......................................................................................................................5
5 DESIGN.................................................................................................................................6
6 MATERIALS AND FABRICATION ....................................................................................9
7 TYPE TESTS.........................................................................................................................9
8 SUPPLY AND INSTALLATION ........................................................................................10
9 MARKING ..........................................................................................................................10
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
APPENDICES
A MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD .........11
B TYPE TESTS ................................................................................................................13
C TYPICAL FORMAT FOR PRESSURE TEST REPORT ..............................................16
AS 4181—1999 4
STANDARDS AUSTRALIA
Australian Standard
Stainless steel clamps for waterworks purposes
1 SCOPE
This Standard specifies the requirements for stainless steel clamps for waterworks purposes.
2 APPLICATION
Stainless steel clamps complying with this Standard are intended for use in the repair or
tapping of water supply pipelines of the sizes designated in Table 1, with a maximum
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
service temperature of 60°C and up to an allowable operating pressure of 1.6 MPa. Repair
clamps have limited ability to accommodate axial deflection and are, therefore, not
generally intended for use as couplings to join two pipes together. However, they are
commonly utilised for repair situations at full pipe break, where the pipe ends are
considered stable.
This Standard does not cover stainless steel tapping saddles whose minimum lengths in
Table 1 are not met and whose seal is not fully circumferential.
Means for demonstrating compliance with this Standard are given in Appendix A.
3 REFERENCED DOCUMENTS
The following documents are referred to in this Standard:
AS
1199 Sampling procedures and tables for inspection by attributes
1349 Bourdon tube pressure and vacuum gauges
1646 Elastomeric seals for waterworks purposes
1722 Pipe threads of Whitworth form
1722.1 Part 1: Sealing pipe threads
1722.2 Part 2: Fastening pipe threads
2129 Flanges for pipes valves and fittings
2205 Methods for destructive testing of welds in metal
2205.10.1 Method 10.1: Corrosion test for welded austenitic stainless steel
3855 Suitability of plumbing and water distribution systems products for contact
with potable water
4020 Products for use in contact with water intended for human consumption with
regard to their effect on the quality of water
4087 Metallic flanges for waterworks purposes
AS/NZS
1111 ISO metric hexagon commercial bolts and screws
1112 ISO metric hexagon nuts, including thin nuts, slotted nuts and castle nuts
1199 Sampling procedures and tables for inspection by attributes
1252 High strength steel bolts with associated nuts and washers for structural
engineering
COPYRIGHT
This is a free preview. Purchase the entire publication at the link below: