Beruflich Dokumente
Kultur Dokumente
Compressive strength
From Wikipedia, the free encyclopedia
Compressive strength is the capacity of a material or structure to withstand axially directed pushing forces. When the limit of compressive strength is reached, materials are crushed. Concrete can be made to have high compressive strength, e.g. many concrete structures have compressive strengths in excess of 50 MPa, whereas a material such as soft sandstone may have a compressive strength as low as 5 or 10 MPa. Compressive strength is often measured on a universal testing machine; these range from very small table top systems to ones with over 53 MN capacity.[1] Measurements of compressive strength are affected by the specific test method and conditions of measurement. Compressive strengths are usually reported in relationship to a specific technical standard.
Contents
1 Introduction 2 Compressive Strength 3 Deviation of engineering stress from true stress 4 Comparison of compressive and tensile strengths 5 See also 6 References
Measuring the compressive strength of a steel drum
Introduction
When a specimen of material is loaded in such a way that it extends it is said to be in tension. On the other hand if the material compresses and shortens it is said to be in compression. On an atomic level, the molecules or atoms are forced apart when in tension whereas in compression they are forced together. Since atoms in solids always try to find an equilibrium position, and distance between other atoms, forces arise throughout the entire material which oppose both tension or compression. The phenomena prevailing on an atomic level are therefore similar. On a macroscopic scale, these aspects are also reflected in the fact that the properties of most common materials in tension and compression are quite similar.[citation needed] The major difference between the two types of loading is the strain which would have opposite signs for tension (positiveit gets longer) and compression (negativeit gets shorter). Another major difference is tension tends to pull small sideways deflections back into alignment, while compression tends to amplify such deflection into buckling.
en.wikipedia.org/wiki/Compressive_strength 1/4
Tension
5/29/12
Compressive Strength
By definition, the compressive strength of a material is that value of uniaxial compressive stress reached when the material fails completely. The compressive strength is usually obtained experimentally by means of a compressive test. The apparatus used for this experiment is the same as that used in a tensile test. However, rather than applying a uniaxial tensile load, a uniaxial compressive load is applied. As can be imagined, the specimen (usually cylindrical) is shortened as well as spread laterally. A Stressstrain curve is plotted by the instrument and would look similar to the following:
Compression
The compressive strength of the material would correspond to the stress at the red point shown on the curve. Even in a compression test, there is a linear region where the material follows Hooke's Law. Hence for this region where this time E refers to the Young's Modulus for compression. This linear region terminates at what is known as the yield point. Above this point the material behaves plastically and will not return to its original length once the load is removed. There is a difference between the engineering stress and the true stress. By its basic definition the uniaxial stress is given by:
where, F = Load applied [N], A = Area [m2] As stated, the area of the specimen varies on compression. In reality therefore the area is some function of the applied load i.e. A = f(F). Indeed, stress is defined as the force divided by the area at the start of the experiment. This is known as the engineering stress and is defined by,
5/29/12
where l = current specimen length [m] and l0 = original specimen length [m] The compressive stress would therefore correspond to the point on the engineering stress strain curve defined by
where F* = load applied just before crushing and l* = specimen length just before crushing.
Barrelling
As a final note, it should be mentioned that the frictional force mentioned in the second point is not constant for the entire cross section of the specimen. It varies from a minimum at the centre to a maximum at the edges. Due to this a phenomenon known as barrelling occurs where the specimen attains a barrel shape.
en.wikipedia.org/wiki/Compressive_strength
3/4
5/29/12
See also
Compression (physical) Box compression test Buckling Deformation (engineering) Schmidt hammer (measuring compressive strength of concrete) Strength of materials Tensile strength.
References
1. ^ NIST, Large Scale Structure Testing Facility (http://www.nist.gov/bfrl/facilities_instruments/large_scale_struct_testing_fac.cfm) , http://www.nist.gov/bfrl/facilities_instruments/large_scale_struct_testing_fac.cfm, retrieved 04-05-2010.
1. Mikell P.Groover, Fundamentals of Modern Manufacturing, John Wiley & Sons, 2002 U.S.A, ISBN 0471-40051-3 2. Callister W.D. Jr., Materials Science & Engineering an Introduction, John Wiley & Sons, 2003 U.S.A, ISBN 0-471-22471-5 3. http://www.foamglasinsulation.com/literature/compressive.pdf Retrieved from "http://en.wikipedia.org/w/index.php?title=Compressive_strength&oldid=473034898" Categories: Materials science This page was last modified on 24 January 2012 at 20:06. Text is available under the Creative Commons Attribution-ShareAlike License; additional terms may apply. See Terms of use for details. Wikipedia is a registered trademark of the Wikimedia Foundation, Inc., a non-profit organization.
en.wikipedia.org/wiki/Compressive_strength
4/4