Beruflich Dokumente
Kultur Dokumente
The best type of glue to use is white school glue (PVA.) Print out the parts sheets onto thin cardboard. If you want to save ink, or prefer to colour in the model yourself, print out the mono pages. Photocopier card is ideal. Notice that the parts pages are marked front and back. Print out a front page, flip it over, then print the back onto the same sheet. Leave the ink to dry completely before continuing. Before cutting anything out, score along all the dotted lines and cut out any holes with a craft knife. Both these jobs are easier to do on full sheets of card. Dashed lines are hill folds, dotted lines are valley folds. Cut along the solid lines. Grey areas show where to glue
Cut out
Thread the long tabs on the wings through the semi-circular holes in the body and glue the body tabs to the wings. (1)
Fold in and glue the three darts on the body. (2) Roll round the body and glue it into place. (3)
Hoot : Instructions 1
3
Glue the head down to the top of the body. (4) It is made slightly too big; once the glue is dry trim the part to size with your scissors. Glue together the beak parts. (5) Glue the beak and eyes to the body. (6)
Youll need two coins about this size. These will act as weights
Wrap the coin holders round the coins. (7) Glue them to the inside front and back of the body. (8)
Glue the push rod end into the top of the head. (11) Use the end of a pencil or a chop stick to press down the flaps to help the glue dry. Fold round and glue together the legs and the push rod as shown above. (9 - 10) Fit the legs into the body. Glue the long tabs to the legs. (12)
Hoot : Instructions 2
Glue the box top to the legs. (13) Fold round the four flaps on the outside(14) Assemble the button as shown below (15) and glue on the button top. (16-17) Glue the button to the end of the push rod. (18)
Fold round and glue down the tabs on the box tabs to make a triangular section. (19) Glue together the two parts of the box and complete it as shown. (20-21)
Complete the owl by gluing the box top to the box. (22) Once the glue is dry make Hoot flap his wings by pressing the button under the box.
Hoot : Instructions 3
Push rod
10
Beak
Eyes
Wings
12
12
HOOT!
Parts. Front 1
Head top
10 11
18
11 11
18
11
6a
6a
11
Parts. Back 1
11
22
Box
20
22 21 21 19 22
13
Box Top
20
www.robives.com 21 17
Legs
Button Top
9.
12
12
HOOT!
Parts. Front 2
17
22
13
Box
13
13
19
21
21
22
21 18
21
Parts. Back 2
22 20 19 22 18 22 20 19 9.
14
14
14
14
15
16
Push Button
16
Body
4 6b
4
4
6a
Coin Holder
8 7
Coin Holder
8 7
HOOT!
Parts. Front 3
14
14
14
14
17
17
15
Parts. Back 1
Push rod
10
Beak
Eyes
Wings
12
12
HOOT!
Head top
10 11
18
11 11
18
11
6a
6a
11
Parts. Back 1
11
22
Box
20
22 21 21 19 22
13
Box Top
20
www.robives.com 21 17
Legs
Button Top
9.
12
12
HOOT!
17
22
13
Box
13
13
19
21
21
22
21 18
21
Parts. Back 2
22 20 19 22 18 22 20 19 9.
14
14
14
14
15
16
Push Button
16
Body
4 6b
4
4
6a
Coin Holder
8 7
Coin Holder
8 7
HOOT!
14
14
14
14
17
17
15
Parts. Back 1