Beruflich Dokumente
Kultur Dokumente
1 INTRODUCTION
This document provides information for the Cambium Networks PTP 600 Series System Release PTP 600-10-04. Software updates for PTP products are available from: www.cambiumnetworks.com/support/ptp/software The information in this document is subject to change without notice. The recommendations, technical data, configurations and statements in this document are believed to be reliable and accurate, but are presented without implied or express warranty. Users must take full responsibility for their applications of any product specified in this document. The information in this document is proprietary to Cambium Networks Ltd.
2 PTP VARIANTS
System Release 600-10-04 is compatible with all existing PTP 600 hardware variants.
3 RELEASED PRODUCTS
3.1 Embedded software
ODU: Boot software, BOOT-01-02 Recovery software, RECOVERY-08-01, RECOVERY-09-00 Standard application software, 600-10-04 UC-APL application software UC-APL-600-10-04 Management Information Base (MIB), 600-10-04 PTP-SYNC: Boot Loader, v0.04 Firmware, v00.07 Main application software, v01.01
4 NEW FEATURES
4.1 New region (RC28) for 5.8 GHz Greece
System Release 600-10-04 supports a new region code (RC28) for operation in Greece, with the following characteristics: 36 dBm EIRP, 23 dBm/MHz EIRP density, 5725 MHz to 5795 MHz.
4.2 New region (RC29) for 5.8 GHz Portugal, Iceland, Serbia
System Release 600-10-04 supports a new region code (RC29) for operation in Portugal, Iceland and Serbia, with the following characteristics: 36 dBm EIRP, 23 dBm/MHz EIRP density, 5725 MHz to 5850 MHz.
Page 3 of 8
Maximum ASCII Series is changed to Maximum Sequential Characters Maximum Consecutive Character Type is changed to Maximum Consecutive Characters Maximum Consecutive Repeated Characters is changed to Maximum Repeated Characters Minimum Number Of Specific Characters is changed to Minimum Mandatory Characters
Page 4 of 8
Page 5 of 8
blocked when the capacity falls below the minimum required, triggering a routing change that brings alternate links into use. Use the Link Planner to determine the capacity of a link at different modulation modes.
4.12 Complete the Installation Wizard without entering the Install Arm State
System Release 600-10-04 replaces the existing Installation Tones control in the web-based interface with a new Installation Mode control. The Installation Mode control allows an operator to change configuration of the ODU through use of the Installation Wizard without arming the ODU for installation. Operators should set Installation Mode to Arm With Tones or Arm Without Tones when installing a new link, when aligning antennas, or when changing link range. Operators may set Installation Mode to Change Config Without Arming when making a configuration change where alignment and range remain constant. The option to complete the Installation Wizard without arming the ODU will be particularly useful if a link is reconfigured whilst it carries significant data traffic. An armed ODU operates in BPSK until disarmed by management action. If armed ODUs are overloaded with data traffic, and are configured without enhanced QoS for network management, this can prevent management of the remote end of the link, and thus disarming of the remote unit.
Syslog message Tx Max Power does not match attribute name Maximum Transmit Power
In 600-10-04, changes to transmitter power are reported using the attribute name Maximum Transmit Power, to match the attribute name on the System Status web-page.
Page 6 of 8
7 TECHNICAL SUPPORT
For Technical Support, please visit our support pages at: www.cambiumnetworks.com/support
Or contact the PTP Technical Support helpdesk using the phone numbers available from:
http://www.cambiumnetworks.com/support/technical.php
Page 7 of 8
Cambium Networks
Cambium Networks provides professional grade fixed wireless broadband and microwave solutions for customers around the world. Our solutions are deployed in thousands of networks in over 153 countries, with our innovative technologies providing reliable, secure, cost-effective connectivity thats easy to deploy and proven to deliver outstanding metrics. Our award-winning Point to Point (PTP) radio solutions operate in licensed, unlicensed and defined use frequency bands including specific FIPS 140-2 solutions for the U.S. Federal market. Ruggedized for 99.999% availability, our PTP solutions have an impeccable track record for delivering reliable high-speed backhaul connectivity even in the most challenging non-line-of-sight RF environments. Our flexible Point-to-Multipoint (PMP) solutions operate in the licensed, unlicensed and federal frequency bands, providing reliable, secure, cost effective access networks. With more than three million modules deployed in networks around the world, our PMP access network solutions prove themselves day-in and day-out in residential access, leased line replacement, video surveillance and smart grid infrastructure applications. Cambium Networks solutions are proven, respected leaders in the wireless broadband industry. We design, deploy and deliver innovative data, voice and video connectivity solutions that enable and ensure the communications of life, empowering personal, commercial and community growth virtually everywhere in the world.
www.cambiumnetworks.com
Cambium Networks and the stylized circular logo are trademarks of Cambium Networks, Ltd. All other trademarks are the property of their respective owners. Copyright 2012 Cambium Networks, Ltd. All rights reserved.