Beruflich Dokumente
Kultur Dokumente
, Inflation
Station and FIA control
Inflation Station (optional)
Automatically fills or
bleeds each tire
No hanging air lines
Louvered Ramps
Prevent wheel spin in
wet conditions
More effective than
diamond tread or
abrasive strips
1
1
1
0
9
8
7
6
5
4
3
2
1
1
2
8.75 in. (222 mm)
Spoiler clearance
Breakover clearance
Hunter offers fully integrated
options to enhance productivity
WinAlign software controls the lift for ultimate
productivity. This patented design offers greater
flexibility and timesaving capabilities.
RX45 Scissor Lift shown with optional Swing Air Jacks, AlignLights, Inflation
Station, PowerSlide
turnplates, WinAlign
Sensors.
PowerSlide
lifts.
147-104-1 Adds 12.75 in. / 324 mm (2 required)
147-113-1 Adds 17.75 in. / 451 mm (2 required)
20-2169-1 Adds 40 in. / 1,016 mm (1 required)
20-2189-1 Adds 50 in. / 1,270 mm (1 required)
The Hunter RX45 Series Scissor Lift has been
certified under the program conducted by
Automotive Lift Institute (ALI) and ETL Testing
Laboratories to comply with Safety Standard ANSI/
ALI, ALCTV and Electrical Standard ANSI/UL 201.
Models
RX45: Surface mounted standard lift with
PowerSlide rear slip plates
RX45F: Flush mounted standard lift with PowerSlide
rear slip plates
RX45IS: Surface mounted standard lift with Inflation
Station & PowerSlide rear slip plates
RX45FIS: Flush mounted standard lift with Inflation
Station & PowerSlide rear slip plates
RX45L: Surface mounted long deck lift with
PowerSlide rear slip plates
RX45LF: Flush mounted long deck lift with
PowerSlide rear slip plates
RX45LIS: Surface mounted long deck lift with Inflation
Station & PowerSlide rear slip plates
RX45LFIS: Flush mounted long deck lift with Inflation
Station & PowerSlide rear slip plates
Add one of the following suffixes to the desired model
number listed above (Example: RX45-43UE):
Suffix Power Configuration
-43UE 208/230/400/460V, 3PH, 50/60HZ
-215E 230V, 1PH, 50Hz
-216E 230V, 1PH, 60Hz
Alignment height All lock positions
Max. lifting height 72 in. (1,829 mm)
Tread width
Min. inside 40 in. (1,016 mm)
Max. outside 88 in. (2,235 mm)
Air Pressure 90-150 psi
Raise Time 55 seconds
Standard Equipment
Two Movable Work Steps (not included with flush model)
Front Wheel Stops
Two Wheel Chocks
Air Line Kit
Full-Floating Rear Wheel Slipplates
Louvered Ramps with Built-In Wheel Stops
RX45 Specications
See Hunter Sales Representative for details
on site requirement.
Form 6284-TE-05, 03/11
0311AAP??M.??
Copyright 2011, Hunter Engineering Company
RX45 RX45L
Max. Vehicle Gross Weight: 10,000 lbs. (4,536 kg) 10,000 lbs. (4,536 kg)
Max. Wheelbase: General service 179/175 in. (4,547/4,445 mm) 192/188 in. (4,877/4,775 mm)
Two-wheel alignment 166/162 in. (4,216/4,115 mm) 179/175 in. (4,547/4,445 mm)
Four-wheel alignment 158 in. (4,013 mm) 158 in. (4,013 mm)
Min. 4-Wheel Alignment: 88 in. (2,235 mm) 88 in. (2,235 mm)
Runway Width: 24 in. (609 mm) 24 in. (609 mm)
Lowered Height: 8.75 in. (222 mm) 8.75 in. (222 mm)
16 in.
(406 mm)
4 in. (101 mm) RECOMMENDED MIN.
22 in.
(559 mm)
24 in.
(610 mm)
7 ft. - 4 1/2 in.
(2,248 mm)
RX10
20 ft. - 1 1/4 in.
(6,128 mm)
RX10L
21 ft. - 2 1/4 in.
(6,458 mm)
39 - 54 in.
(991 - 1,372 mm)
16 in.
(406 mm)
11 5/8 in.
(295 mm)
OPTIONAL
EXTENDED
WHEEL STOP
RX45 Plan View
11250 Hunter Drive, Bridgeton, MO 63044 U.S.A.
l|. !J!4J!JJ2J * |+/. !J!4J!J!J2
E-mail: international@hunter.com
surface/flush