Beruflich Dokumente
Kultur Dokumente
* ** Important concepts and equations in MECH 202 Calculation of mechanical and thermal stresses in thick-walled cylinders and disks
1.1 The Theory of Elasticity (MECH 202) Method Equilibrium Equations and boundary Conditions and Strain-Displacement Relations 1.2 Equilibrium Equations, Stress, Strain and Displacement formulas for thick- walled cylinders and spinning disks 1.3 Thick-walled cylinder under Pressure, Compound Cylinders 1.4 Stresses in spinning disks 1.5 Thermal stress in cylinders and disks
Strain-displacement relations
FIGURE 2.3.1. Lines OA and OB are drawn on a body in its strain-free state. As a result of loading, configuration OAB is converted to OAB. Equations 2.3.3 are derived from this sketch.
Strain-displacement relations
(2) Normal strain
Saint-Venant's Principle
If a system of forces acting on a small region of an elastic solid is replaced by another force system, acting within the same region and having the same resultant force and moment as the first system, then stresses change appreciably only in the neighborhood of the loaded region.
FIGURE 2.2.3. Illustration of Saint-Venant's principle. When distributed pressure loads (a) Are replaced by statically equivalent concentrated loads (b) Stresses change considerably near theloads (shaded regions), but change little elsewhere.
1.2 EQUILIBRIUM EQUATIONS, STRESS, STRAIN AND DISPLACEMENT FORMULAS FOR THICK-WALLED CYLINDERS AND SPINNING DISKS
FIGURE 3.2.1. (a) Cross section of a thick-walled cylinder, under internal pressure Pi and external pressure Po , or plan view of a disk spinning with constant angular velocity . (b) Force that act on a differential element of dimensions r d by dr by h, where h is the (constant) thickness of the disk or a typical length along the cylinder. The mass density is .
1.3 THICK-WALLED CYLINDER UNDER PRESSURE, COMPOUND CYLINDER THICK-WALLED CYLINDER UNDER PRESSURE, COMPOUND CYLINDER
Thick-walled cylinder under pressure (w = 0)
(b) stress formulas By using above boundary conditions the constants C1 and C2 are found to be
a = 3b
a = 3b
FIGURE 3.4.2. Stress at r= b due to internal pressure only. The upper curve is the Lam solution. The lower curve is the thinwalled equation, = Pib/t. The middle curve uses the mean radius R = (a + b)/2 in place of b in the thin-walled equation.
FIGURE 3.4.3. Pressurized holes in a flat body of arbitrary contour. If holes are widely separated and not close to an edge, stresses at the holes due to pressure P are much like stresses in a very thick pressurized cylinder.
(1)
If t/b < 0.1 (thin-wall), the stress solution for thin-wall is almost the same as thick-wall cylinder. In a cylinder with closed ends, axial force is provided by pressure against the end caps, the axial stress due to internal and external pressure load is
(3)
Compound cylinder (1) More efficient use of material (2) Shrink-fitting The contact pressure Pc due to shrink-fitting depends on the radius mismatch , i.e., Ur(outer-cylinder) (Pc , ) Ur(inner-cylinder) (Pc , ) =
FIGURE 3.6.1. (a) Stresses produced by shrink-fit contact pressure Pi at thin interface of a compound cylinder. (b) Stresses produced by the combination of shrink-fit and internal pressure. Dashed lines represent stresses due to Pi alone.
Once Pc is known, the residual stress in the 2 cylinders can be calculated by Lam solution Superposing the stresses of internal pressure Pi more efficient use of material
* A small central hole doubles the stress over the case of no hole!
FIGURE 3.7.1. Stresses r and in elastic spinning disks of constant thickness. (a) Solid disk. (b) Disk with a central hole.
Example
FIGURE 3.7.2. Two days to connect a disk and a shaft. The second way, with a solid disk and a discontinuous shaft, results in lower stresses. Larger flanges (dashed lines) allow bolts to be placed farther from the axis, where disk stresses are lower.
A steel disk and a solid shaft are connected by shrink-fitting. To determine: (1) What are the stresses at standstill; (2) At what speed the shrink-fit will loosen; and what are the stresses at this speed; (3) What are the largest and contact pressure at half this speed.