Sie sind auf Seite 1von 21

5.

THEORY OF ELASTICITY

12/11/2012

5. THEORY OF ELASTICITY
I gor Kokcharov

5.1 DEFORMATION
An elastic body can be shifted and extended. Analysis of the displacements u, v and w shows whether there is deformation or not. Change of the element sizes and its shape can be characterized by deformation, difference in displacements, or by strain. Strain is the deformation of an element divided by the original length of the element. There are 6 components of strain. There is linear strain ei and shear strain g ij . The strain e x is the derivative of displacement u with respect to coordinate x. Definitions for the other strain components are shown in the figure. Volume expansion e depends on linear components of strain only. Shear strain g xy has no affect on the parameter.

The strain components change if the axes is rotated by angle q. According to the second formula shown at the right, shear strain g xy = 0 if all three linear components of strain are equal.

In an elastic body strains cannot be chosen arbitrarily, they must satisfy to the strain compatibility equations.

http://www.kokch.kts.ru/me/t5/index.html

1 / 21

5. THEORY OF ELASTICITY

12/11/2012

For plane strain there are two axes along which the linear strains are at a maximum. The axes are called principle axes. Angle q defines their position. The expressions are given for maximum linear strains e 1, e 2 (plane problem) and maximum shear strain gmax (three-dimensional problem).

The radial displacement w is smaller in the center of rotating disk. The displacement is a result of summation under the shown curve of radial strain e r. The larger radial strain and gradient of the displacement are observed in the central part of the disk.

5.2 STRESS
Stress is the intensity of an internal force acting on a point in an object. Stress is measured in units of force per area. Axial (or normal) stress (s) is defined as the force perpendicular to the cross sectional area of the body divided by the cross sectional area. Shear stress (t) acts parallel to an imaginary plane cut through an object. Centrifugal forces act to move an elementary ring from center. The elementary ring is extended. Both shown stress components, radial and tangential, are positive.

There are 9 stress components at any point. The condition for zero rotation of the element, found by taking moments about the axes through the center of the cube parallel to the coordinate axes, reduces the number of independent components to six. Six stress components are enough to describe any state of stress in a
http://www.kokch.kts.ru/me/t5/index.html 2 / 21

5. THEORY OF ELASTICITY

12/11/2012

point.

The equilibrium equations must be satisfied for an elastic body. Mass is not considered in the equations. The shown stress components correspond to three-point bending and satisfy the equilibrium equations.

The cut element must be in equilibrium. This requirement helps find the stresses at the incline planes. The sum of the forces at axis x equal to zero. Force is equal to stress * area. The formula gives the expression for principle stresses - normal maximum stresses at incline planes at a point in plane stress state.

The shown normal stresses are principle because there are no shear stresses at the planes. The maximum shear stress acts at an incline plane between maximum and minimum principle stresses s 1 and s 3. Maximum shear stress, t max = (6-(-4))/2 = 5 MPa. For all around tension where the three principle stresses are equal there is no shear stress at any incline planes. All rectangular coordinate sets can be considered the principle ones. The normal stress at any incline plane is also equal to 1 MPa. The fringe pattern in the photoelastic film shows lines of equal shear stress t max. Maximum shear stress is equal to one-half the maximum tensile stress. The picture illustrates the regions of high stress (density of the fringes).

http://www.kokch.kts.ru/me/t5/index.html

3 / 21

5. THEORY OF ELASTICITY

12/11/2012

5.3 HOOKE'S LAW


For elastic deformations the normal stress is directly proportional to strain. The ratio of axial stress/strain is a constant. This constant is known as Y oung's modulus or modulus of elasticity E. Y oung's modulus is directly proportional to the axial stress and inversely proportional to the axial strain.

For three-dimensional stress state the formulas include more than one stress component. The expressions for isotropic elastic body include three elastic constants of material: modulus of elasticity E, Poisson's ratio m and shear modulus G. The elastic constants are characteristics of the material. They do not depend on the shape or size of the specimen. The shear modulus G can be expressed by the first two elastic constants. There are only two constants that are independent parameters for an isotropic material.

Poisson's ratio m characterizes transverse deformation under axial tension or compression. It is a dimensionless parameter. For m=0.3, axial tension of 10% corresponds to a transverse compression of 3%.

http://www.kokch.kts.ru/me/t5/index.html

4 / 21

5. THEORY OF ELASTICITY

12/11/2012

The expressions show another form of the Hooke's law. Normal stress sx depends on all three linear components of strain e x, e y and e z.

Volume expansion e characterizes an increase of an element size, not a change of its shape. It depends on the linear strains only. The volume expansion e can be defined by the elastic constants of the material E, m and the sum of the normal stresses s x, s y and s y.

5.4 PLANE PROBLEMS


There are two special states of stress: plane stress for thin plates and plane strain for thick plates. For plane stress there are four non-zero strain components (e x , e y , e z , g xy ) and three non-zero stress components (s x , s y , t xy ). The plane stress is typical for thin-walled structures such as in airplane wings. For plane strain there are three non-zero strain components (e x, e y, g xy) and four non-zero stress components (s x, s y, s z, t xy). Plane strain is typical for thick plates.

http://www.kokch.kts.ru/me/t5/index.html

5 / 21

5. THEORY OF ELASTICITY

12/11/2012

There are two equilibrium equations that must be satisfied for absence of mass forces. Elastic plates have stress fields that satisfy Hooke's law and the strain compatibility equations. The two stress components shown correspond to an embedded beam with a force applied to the right end. The equilibrium equations help solve the plane problems of the theory of elasticity.

There are two inclined principle planes where there is no shear stress and normal stresses (s 1 and s 2) are at a maximum.

Principle axes are inclined 45 o to the direction of shear stress t for pure shear. Indication A is negative. There are zero indications for B and D.

http://www.kokch.kts.ru/me/t5/index.html

6 / 21

5. THEORY OF ELASTICITY

12/11/2012

The figure shows typical stress patterns for s x, s y and t xy. The normal stress sx is usually higher than other stress components for a long beam, where Length >> Height.

There is concentration of shear stress in the area where force is applied. Shear stress is equal to zero at the surface and is at a maximum in a neighboring region.

Normal stress s y at axis x can be positive outside the zone of compression. Here, the compressive stress is significantly higher than the tensile stress.

Saint-Venant's principle. At a distance equal to width of the beam (2a), the maximum stress does not exceed the nominal stress by 4%. The stress pattern becomes practically uniform.

http://www.kokch.kts.ru/me/t5/index.html

7 / 21

5. THEORY OF ELASTICITY

12/11/2012

5.5 TORSION
Torsion is related to shear stress. Only two shear stresses are nonzero at planes perpendicular to the shaft axis. All other stress components including all normal stresses in the chosen coordinate axes are equal to zero. There is no tensile strain in the vertical or horizontal directions for pure shear (torsion). There are no readings on the two strain gauges shown.

The figure shows the results of a finite element analysis for a prismatic bar under torsion. The shear deformation is at a maximum in the center of the bar. The shape of the square mesh at the surface of the bar changes. The height of the rhombus and its area become smaller. This means that the bar becomes a little shorter.

The figure shows four specimens with equal cross sections. The thinwalled example A demonstrates the smallest torsional rigidity. The specimens are shown in increasing order of the torsional rigidity. Deplanation of a plane section is the out-of-plane deformation of its points. For all examples except cylinder D there is deplanation.
http://www.kokch.kts.ru/me/t5/index.html 8 / 21

5. THEORY OF ELASTICITY

12/11/2012

Shear stress is doubled near the small keyslot. The stress concentration factor is equal to 2 for the small keyslot. There is stress concentration near the diameter change. The stress concentration factor depends on radius of curvature.

The formula defines maximum shear stress for a rectangular section. The maximum shear stress acts at the middle of the longer edge of the rectangle. The coefficient k grows from 0.208 at b/a=1 to 0.333 at infinity.

Maximum shear stress in the middle of a side of a triangle is inversely proportional to a 3. The shear stress is equal to zero in the corners and center.

http://www.kokch.kts.ru/me/t5/index.html

9 / 21

5. THEORY OF ELASTICITY

12/11/2012

For thin-walled symetrical sections the shear stress is approximately zero in the inner wall. All shear stresses tend toward the "external circle".

5.6 BENDING
There are shear and tensile stresses in bending beams. Usually the beams fail due to bending tensile stress. An exception is beams with high h/L ratio. A height increase results in an increase in the t max/s max ratio. The shear stress is at a maximum and there is no tensile bending stress at the neutral line of a bending beam. The maximum tensile stress act at the upper or lower segments of the beam. The principle planes are planes where there are no shear stresses and the normal stresses are at a maximum. The principle axes are inclined by 45 o to the neutral axis. The principle axes coincide with the coordinate axes at the upper and lower sections of a bending beam.

The neutral line is shifted to the center for a curved beam. The absolute value of the maximum compressive stress is smaller than that for tension for the shown loading condition. For R/h > 20 the stress field can be considered the same as for a straight beam.

The maximum shear stress depends on the transverse force F, the cross-sectional area A and Poisson's ratio m. The shear stress is at a maximum in the center of the section. The bigger the distance from the neutral axis, the bigger the bending tensile stress.
http://www.kokch.kts.ru/me/t5/index.html 10 / 21

5. THEORY OF ELASTICITY

12/11/2012

There is a stress concentration in the bending beam. The stress concentration factor depends on the ratio of the radius of curvature to the decreased height of the beam.

The figure shows a curved central line of the beam. The angle of rotation is at a maximum at the right edge of the beam.

Shear stress can result in torsion of non-symmetrical sections. Applying force at a distance e=0.548r does not cause torsion of the beam with a half-round cross section.

http://www.kokch.kts.ru/me/t5/index.html

11 / 21

5. THEORY OF ELASTICITY

12/11/2012

5.7 POLAR COORDINATES


There are tangential s q and radial s r stress components in polar coordinates. The coordinates are used for round elastic bodies. The tangential tensile stress is at a maximum at the inner surfaces of a cylindrical tube with inner pressure p i, A. The tangential stress is negative for external pressure B. There is no stress gradient if the external and inner pressures are equal, C. The eccentricity e increases the maximum tensile stress at inner surface, D.

There is a stress concentration near the round hole in the plate. The stress concentration factor is equal to the ratio of the maximum to the nominal stress. Stress concentration factor is 3.0 for point 2 . Stress s y is negative for point 1. Compression is similar to tension, merely change the signs. For the complex loading shown here, the tangential stress sq is at a maximum in the horizontal section due to the effect of "tension + bending + stress concentration".

http://www.kokch.kts.ru/me/t5/index.html

12 / 21

5. THEORY OF ELASTICITY

12/11/2012

Stress concentration is higher for an elliptical hole under tension than for a round hole. For pure shear the absolute value of normal stress is highest at a point between A and C. For a round hole (a=b) the stress concentration factor is equal to 4 for pure shear. The stress pattern is linear for bending except near the elliptical hole where stress increases.

The theoretical stress concentration factor for an ideal elastic body is equal to infinity in the crack tip. Infinite stress is not seen in actual materials due to plasticity and finite microstructure.

The tangential stress is equal to the radial stress for this loading scheme. The stress depends on angle q, not on the radius r. The smaller the angle q, the larger the absolute value s q. The stress is equal to distributed load q at the surface (q=0).

http://www.kokch.kts.ru/me/t5/index.html

13 / 21

5. THEORY OF ELASTICITY

12/11/2012

A rotating disk: g is the density of material, m is Poisson's ratio, w is the rotation speed. The radial stress is higher than the tangential stress. It is proportional to the squared rotation speed and highest in the center.

5.8 PLATES
Bending is the most important loading situation for thin plates. Bending moment depends on bending rigidity D of the plate and the shape of the deformed plate (deflection and its derivatives). The bigger the thickness h, the bigger the bending rigidity D and the absolute value of the bending moment. Maximum bending stress is proportional to bending moment M and inversely proportional to h 3. There is usually bending relative to both axes x and y. For the shown embedded thin plate, upper layers are under compression and lower layers are under tension in the center of the plate. Both normal stress components s x and s y are at a maximum at the lower surface of the plate.

The maximum deflection for a round simply supported plate with a force in the center is proportional to (a/h)2. The maximum stress and deflection depend on the support method. The more rigid support, the smaller the maximum bending stress s max and maximum deflection of the round plate.

http://www.kokch.kts.ru/me/t5/index.html

14 / 21

5. THEORY OF ELASTICITY

12/11/2012

The plate shown here is loaded with evenly distributed forces. The maximum deflection in the center the of plate is inversely proportional to h 3. Cutting the thickness h in half increases the deflection by 8 times. For a rectangular plate with a force in the center, the bending stress is at a maximum in the middle of the longer side.

The stress concentration factor as is smaller for bending of thin plate than for tension of a plate (a s=3.0). The stress concentration factor for bending depends on Poisson's ratio m. It is approximately equal to 1.8 for steel (m=0.3).

The upper surface of the plate was rapidly heated to 100 oC. This causes thermal bending stress in the plate. The thermal stress depends on the difference in temperatures, thermal expansion coefficient and elastic constants of the material. The thermal stress does not depends on the thickness h.

http://www.kokch.kts.ru/me/t5/index.html

15 / 21

5. THEORY OF ELASTICITY

12/11/2012

5.9 SHELLS
The tangential stress is equal to meridian stress for spherical shells. Radial displacement (radius increase) is directly proportional to the inner pressure and R 2. The bigger the Y oung's modulus of the material, the smaller the displacement.

The tangential stress for a cylindrical pressure vessel is twice as large as the meridian stress.

The radial displacement is proportional to pressure. The bigger the displacement, the smaller the gap between the cylindrical vessel and the wall. There is a pressure when the gap is zero.

http://www.kokch.kts.ru/me/t5/index.html

16 / 21

5. THEORY OF ELASTICITY

12/11/2012

Tension in the X-direction results in deformation in the vertical direction. This theory gives the formula for calculation of the displacement d y.

A cylindrical shell is compressed. The figure shows patterns of deflection w, angle of rotation q, bending moment M and transverse force Q.

The bending moment and bending stress are at a maximum at the bottom of the tank. The most effective use of material utilizes thicker parts at the bottom.

The tangential and radial stresses are at a maximum in the bottom of the water tank. There is a quadratic dependence of the stress on the radius of the half-sphere R.

If a spherical dome accepts its own weight, the increase in thickness h results in an increase of the shell weight and its bending rigidity. The
http://www.kokch.kts.ru/me/t5/index.html 17 / 21

5. THEORY OF ELASTICITY

12/11/2012

two factors compensate for each other. Therefore, maximum stress does not depend on thickness of the shell.

A thin-walled cylindrical ring can lose its shape due to a pressure increase. The more rigid the material, the bigger the critical stress. Critical pressure is proportional to Y oung's modulus E.

A thin wall cylindrical shell can lose stability at shear stress t critical. Geometrical parameters have different effects on the critical stress. Length L has no effect on the critical stress t critical. The bigger the radius R, the smaller the stress. The bigger the thickness h, the bigger the critical stress t critical.

5.10 CONTACT STRESSES


The shape of the contact area between two elastic bodies is usually circular, elliptical or rectangular. This is valid for ideal elastic bodies.

http://www.kokch.kts.ru/me/t5/index.html

18 / 21

5. THEORY OF ELASTICITY

12/11/2012

The size of the contact area depends on the modulus of elasticity of the balls, their radii and the compressive force F. It is proportional to F 1/3. Absolute value of the contact normal stress s 3 is at a maximum at the contact surface. The two other components are 80% of s 3. Maximum shear stress acts inside the ball at 0.4a from the surface.

For compression of two balls the contact stress is at a maximum in the center of the contact spot. The stress decreases to zero at the edges of the contact region. For the two other loading situations, the stress is not the highest in the center. The theory of elasticity predicts the maximum contact stress for ball bearings. The smaller contact stress, the better. The smaller the modulus of elasticity E, the smaller the contact stress. The hardness, not the contact stress, is more important in choosing the material for ball bearings.

http://www.kokch.kts.ru/me/t5/index.html

19 / 21

5. THEORY OF ELASTICITY

12/11/2012

Shear stress in a rail is approximately equal to zero at the surface (z=0) and is at a maximum at a distance 0.45a from the contact zone, where a is size of contact region.

The distance between the centers of the cylinders decreases with an increase in force. There is no linear dependence for the elastic displacement D.

Time of contact for impact between two steel balls in a ball mill is proportional to the radius of the balls R. Increase in the modulus of elasticity or in velocity decreases the time of contact. The bigger the size of the balls the longer the time of contact.

REFERENCES
S.P. T imoshenko, J.N. Goodier T heory of Elasticity, McGraw-Hill, N. Y., 1970. S.P. T imoshenko, S. Woinowsky-Krieger T heory of Plates and Shells, McGraw-Hill, N. Y., 1959.

http://www.kokch.kts.ru/me/t5/index.html

20 / 21

5. THEORY OF ELASTICITY

12/11/2012

THEMES
Theme Theme Theme Theme Theme Theme Theme Theme Theme Theme 1. Stress Concentration PDF (1.4 MB) 2. Fracure Mechanics PDF (2.2 MB) 3. Mechanical Properties 4. Strength of Materials 5. Theory of Elasticity 6. Structural Safety 7. Material Science 8. W elds 9.Composite Materials 10. Finite Element Analysis

_____________________ 2012______________________

http://www.kokch.kts.ru/me/t5/index.html

21 / 21

Das könnte Ihnen auch gefallen