Beruflich Dokumente
Kultur Dokumente
I-IH
-E--
-E
S* "{
Deluxe equipment
DX400B complete incli.rding:
4754596
1 piston
1 cleaning c oth
4995312
1 stop rino
extractor 0402984
4tw 6-20
o402270
5 ,l
pislon
4/NK
lor NK drive pins
0402219
'l
r pacKage
ol 5 stop
1 baseplate
l
0402101
baseplate
4BlF1
4S/F6
0402106
HHl:IHhI
1 pair satety
rings
0451655
E!TTIf
goggles 4654032
4553776
1 flat
3/T69
wire brush
4553840
_l-*-
(ox4oo
t-Qm
1 2
rE
r,.;''li -li_
9
lM;\l,i /i,i'i',i'lV
10 1t
12
3 4 5 6
7 9
10 11 12 13
baseplate front guide stop ring stop pressure piston chamber firing pin return firing firing pin firing pin end
4BlF1 0402101 cap 0402931 o4o2941 sleeve holder 0402986 ring 0451655 spring O4O2937 bushing 0402913 spring o4o292g pin 0402924 guide 0402926 spring 0402930 O4O2922 cap
Catalog No.
N,,VVJ..ll
r t-r 13 ll
ll
-l
-ri
Operating precautions
1. Never load the tool until you are ready to use d. 2. Never cock the toolagainst the hand or point the tool at anyone. 3. lf a booster tails to igniie: a) Keep the lool pressed against the work surface for thirty (30) seconds. b) lf the boosterdoes not ignile, withdraw the tool approximately 2" from the work surface (to
recock the tiring mechanism), taking care thal it never points at yourself or anyone else. Do not pullthe baseplate out. c) Beposition the tool against the work surface, fully depress the guide, and again squeeze the trigger. d) lf the boosler still fails to ignite, wait another thirty (30) seconds, carefully remove the toolfrom the work surface,
pull oui the baseplate untilthe top of the booster magazine protrudes from the top of the tool. e) Remove the entire booster magazine from the tooland carefully dispose of it by placing il in a container of water or oil. Do not aitempt to use other boosters on the maga-
before: Work breaks Changing parts Cleaning and servicing Storing at the end of the day. 5. Never leave a loaded tool unattended. 6. Use the rubber stabilizer whenever possible. 7. Always wear safety goggles and hard hat when operating powder-actuated tools. Use ear
protection when working in confined areas. B. Do not attemptto use a defeclive tool. 9. Keep boosters of ditferent types segregated and clearly identified. 10. Only use auihenlic Hilli fasleners. boosters, and parts !n your tool.
Application restrictions
1 . Never attempt to fasten at an angle to the work surface. 2. Neverfasten through a pre-
drilled hole unless adequate guidance is provided. 3. Never fasten into a spalled area on concrete.
4. Never make fastenings in an explosive orflammable atmosphere. 5. Never attempt to lasten into very hard or brittle materials, such as cast iron, glazed tile, suriace-hardened or high-
tensile-strength steel, glass block, live rock, face brick, or hollow lile. 6. Never fasten to concrete closerthan 2 inches trom an unsupported edge or corner, unless a special guard, jig, or
fixure is used orthe specific application is approved. 7. Minimum iastener spacing in concrete is 2%". 8. Minimum fastener spacing in steel is 1".
Warranty
I his new fasrenrng lool is a quality product of Hihi. lt has been developed through study and research into construction fastening methods and applications. Every reasonable precaution has been taken in the manufaciure of the tool to assure that it complies with Hilti's standard of high quality. The Hilli tool is warranted lor 5 years to the original purchaser from the date of shipment. The warranty is against defects in material or workmanship, provided that the system is used in accordance with Hilli instructions; repairs have not been made by persons olher than authorized Hilti service personnel; damage is not due to normal wear and tear; the tool has not been abused or misused: and lhe defective iool is returned
to the local Hilti representative for forwarding to the Hilti Repair Center. Parts which are found lo be defective in material or workmanship will be replaced or repaired without cost other lhan the cost of shipping and insurance. Under no circumstances will Hilti be obligated for consequential or other damages, losses or expenses in connection with or by reason of the use or inability to use the toolfor any purpose.
This warranty, which is given expressly and in lieu of all other wafianiies, expressed or implied, of merchantability, and oftitness for particular purpose, conslitutes the only warranty or guarantee made by Hilti.
rll