Beruflich Dokumente
Kultur Dokumente
3 CDTI 66 KW
OpEL CORSa D 1.3 CDTI 66 KW EngInE
Even when chain drives are ultra low-maintenance and impress with their extremely long service life, at some point they need to be replaced. For the Opel Corsa D 1.3 CDTI 66 KW engine as well, you can rely on the high-quality precision components from RUVILLE, your system specialist. During repair work, both general as well as specific procedures have to be followed for the respective components.
gEnERaL InSTRUCTIOnS
Basic installation instructions: Disconnect the battery Important note: For vehicles equipped with ESP systems, the steering angle sensor has to be recalibrated each time the battery is disconnected! Remove the spark plugs so that the engine can be rotated more easily Unless otherwise specified, do not rotate the engine in the reverse direction of the engine running direction Observe the tightening torques Only rotate the engine using the crankshaft wheel, do not use the camshaft wheels Do not rotate the crankshaft wheel or camshaft wheels if a chain is not mounted.
aLL RUVILLE ChaIn DRIVE COMpOnEnTS FOR ThE OpEL CORSa D 1.3 CDTI 66 KW
article no. 3458003 3458004 3458008 3458006 3458007A1 3453014 1x Description Tensioner element Guiding rail Timing chain Sprocket Sprocket Tensioner rail Sealing (included in kit 3458010SD) Sealing ring (included in kit 3458010SD) Timing chain kit: Complete kit with seals Timing chain kit: Complete kit Timing chain kit: Small kit
nEW
IL CAN ALSO BE KNOW-HOW IN DETA E AT DOWNLOADED ONLIN S RVICE DOWnLOaD SE WWW.RUVILLE.DE MpOnEnTS aTIOn EngInE CO TEChnICaL InFORM a D 1.3 CDTI 66 KW FOR ThE OpEL CORS
Nissan Almera, Primera, Pathfinder; Volvo BMW 5, 7, 8 series Ford Fiesta, Ka Opel Astra, Omega, Vectra; Saab 9-3 Opel Astra, Omega, Vectra; Saab 9-3
KnOW-hOW In DETaIL
pagE 1
1 2
13. Before mounting the new components, clean all contact and installation surfaces until they are free of oil and grease. 14. Mount all chain drive components and fasten them using the correct tightening torques. 15. When installing the timing cover, the timing case must be centred on the crankshaft using the EN-46775 centring pin (1). 16. Replace the radial shaft sealing ring for the crankshaft in the timing cover using the sealing ring included in kit 3458010SD. Wet the sealing lip with oil and press-fit the new sealing ring using the EN-46776 adapter (2). 17. Mount all components by reversing the procedure described above. Make sure to observe the tightening torques 18. Remove all locking tools. 19. Rotate the engine by 720 in the engine running direction. 20. Check the valve timing using the locking tools for the EN-46781 camshaft and EN-46785 crankshaft.
6. Rotate the engine slowly in the engine running direction until you can hear the EN-46781 camshaft locking tools EN-46781 lock into place. Make sure that the locking tools do not turn or twist out of position during this procedure. 7. Insert the locking pin for the EN-46785 crankshaft into the drill hole of the transmission bell housing. Important note: Position the locking pin by gently rotating the central bolt in the flywheel. 8. Dismount the crankshaft vibration damper. 9. Remove the flange for the crankshaft vibration damper using the KM-662-C tool. Important note: The central bolt has a left-hand thread. 10. Dismount the water pump. 11. Dismount the timing cover.
BRanD nEW
ChaIn KIT FOR ThE OpEL CORSa D 1.3 CDTI 66 KW anD 8 MORE MODELS!
KnOW-hOW In DETaIL
pagE 2