Beruflich Dokumente
Kultur Dokumente
Overview Step 1: Installing CPU Step 2: Installing CPU Heat Sink and Fan Assembly Step 3: Installing Notebook Memory Step 4: Installing Mini PCI WLAN Card Step 5: Installing Notebook Hard Drive (HDD) Step 6: Installing the Battery Step 7: Final Check Step 8: Entering BIOS
p. 1 p. 3 p. 4 p. 5 p. 6 p. 8 p. 10 p. 10 p. 11
Installation Guide
Overview
MS-1016 is shipped out as a bare bone. Some of the components are equipped while some are not. This installation guide provides you with the information of notebook hardware setup. Before assembling your Notebook, please prepare for the installation tools and appropriate items. If you are not clear about the items, please contact your dealer for more information.
Open View
1. Cover latch 2. Display Panel 3. Quick Launch Buttons and Power button 4. Status LEDs 5. Keyboard 6. Touchpad 7. Stereo Speakers
Bottom View
1. CPU Compartment 2. Mini PCI Drive Compartment 3. Memory Compartment 4. Hard Disk Drive Compartment 5. Battery Unlock Button 6. Battery Pack
Front View
Rear View
Warning!
Ensure power is turned off and Notebook Battery is removed before you install any hardware devices. Use a grounded wrist strap before handling computer components such as CPU, Memory, HDD, mini-PCI Card, etc. Place components (CPU, Memory, HDD, mini-PCI Card, etc) on a grounded antistatic pad or on the bed that came with the components whenever the components are separated from the Notebook. If there are any difficulties installing hardware devices, please contact your dealer for further information. Right View Left View
p. 1
p. 2
1-2 Locate the golden cut edge on the CPUs upper right-hand corner. Then insert the CPU into the socket. !! The CPU will only fit in the coorect orientation !!
!! Be sure to install CPU fan connector correctly. Dont force. Diagram shown is wrong !!
1-3 Adjust the CPU socket by turning the screw. Make sure the CPU is properly installed. Then press the CPU evenly by hand and turn the screw using a flat head screw driver to lock the CPU in place. !! Please make sure the golden cut edge location is aligned with the notch of the CPU socket. If the CPU does not align with the CPU socket, it will damage the CPU !!
2-2 Align the CPU heat sink and fan assembly in the correct direction. Hint: We recommend you to apply the given thermal grease for better heat conduction between your CPU and heat sink.
2-3 Slide the head sink and fan into correct position.
p. 3
p. 4
2-4 Push down carefully making sure to align the four screws to the board.
3-2 Push down the memory module gently until the metal-locking levers aside from the DIMM socket 1 is fastened.
2-5 a.b.c.d. Tighten the four screws in a diagonal direction. !! Improper connection of the CPU heat sink fan and/or without plugging the fan connector will damage the notebook and CPU !! a. b.
3-3 If you have more than one memory module, please align the 2nd memory module to the DIMM socket2. !! Memory module can only fit in one direction due to the keyed notch. Wrong orientation will cause improper installation and may damage the memory modules or DIMM sockets !!
c.
d. 3-4 Push down the memory module gently until the metal-locking levers aside from the DIMM socket 2 is fastened.
p. 5
p. 6
4-2 Adjust the attached antennas and push down the Mini PCI Card gently until the metal locking levers aside from the Mini PCI socket is fastened. !! Mini PCI Card can only fit in one direction due to the keyed notch. Wrong orientation will cause improper installation and may damage the Mini PCI Card or Mini PCI socket !!
5-2 Insert the HDD into the given HDD shielding tray. !! Improper alignment will cause damage to the HDD and the Notebook !!
4-4 After connecting the black wire, connect the gray wire to the AUX connector.
!! Be sure to install HDD correctly. You should not be able to see the circuit board. Diagram shown is wrong !!
4-5 a.b. After installing the CPU, Memory, and Mini PCI Card, gently slide the cover until it locks into position. Lock down the cover by applying 3 screws. a. b.
5-3 a.b. After sliding the shield over the HDD, slide the connecting shield to the HDD and shield. !! Be sure to fasten the screw that are provided !! a. b.
p. 7
p. 8
5-4 a.b. After installing the shield, slide the HDD into the HDD bay. !! Be sure to have HDD plastic puller face up !! a. b.
5-5 Push HDD towards the side until HDD can go no further.
c.
5-6 a.b. After installing the HDD, gently press down the cover then slide. Lock down the cover by applying 2 screws. !! Failure to apply 2 screws may cause HDD assembly to fall of in notebook HDD area and will damage the HDD and notebook !! a. b.
p. 9
p. 10
8-3 Insert a Bootable OS CD into the OSD tray. 8-4 To save/exit the BIOS Setup Screen, press Y to save/exit.
8-5 After seeing the Intel Logo, immediately press Enter in order to install OS and follow the given setup messages. 8-6 After installing OS, insert the given Driver CD to install the appropriate drivers in order. Hint: If you have any questions related to the BIOS Setup procedure or if there are any other issues, please contact your local retailers or national distributors for further support.
8-2 Under BOOT menu in the BIOS Setup Utility, press <Enter> to select the first boot device.
p. 11
p. 12