Beruflich Dokumente
Kultur Dokumente
SECTION
BCS
CONTENTS
BCM BASIC INSPECTION ................................... 3 .
DIAGNOSIS AND REPAIR WORKFLOW ......... 3 .
Work Flow ................................................................ 3 . WIPER : CONSULT - III Function ...........................21 . FLASHER ..................................................................22 . FLASHER : CONSULT-III Function ........................22 . COMB SW .................................................................22 . COMB SW : CONSULT-III Function .......................22 . FUSE, FUSIBLE LINK ..............................................23 . FUSE, FUSIBLE LINK : CONSULT-III Function .....23 . BATTERY SAVER ....................................................23 . BATTERY SAVER : CONSULT-III Function ...........23 . SIGNAL BUFFER .....................................................24 . SIGNAL BUFFER : CONSULT-III Function ............24 . AIR PRESSURE MONITOR ......................................25 . AIR PRESSURE MONITOR : Diagnosis Description ..........................................................................25 . AIR PRESSURE MONITOR : CONSULT-III Function ..........................................................................26 .
BCS-1
2007 Altima
BCS-2
2007 Altima
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
OVERALL SEQUENCE
INFOID:0000000000994418
BCS
P
JPLIA0089GB
BCS-3
2007 Altima
DETAILED FLOW
2. SYMPTOM CHECK
Check the symptom from the customer's information. >> GO TO 3..
3. BASIC INSPECTION
Check the operation of each part. Check that any symptom occurs other than the interviewed symptom. >> GO TO 4..
7. SYSTEM DIAGNOSIS
Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part.
>> GO TO 9..
8. SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part. >> GO TO 9..
BCS-4
2007 Altima
BCS
BCS-5
2007 Altima
FUNCTION DIAGNOSIS
BODY CONTROL SYSTEM
System Description
OUTLINE
BCM (body control module) controls the various electrical components. It inputs the information required to the control from CAN communication and the signal received from each switch and sensor. BCM has combination switch reading function for reading the operation status of combination switches (light, turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical components. It also has the signal transmission function as the passed point of signal and the power saving control function that reduces the power consumption with the ignition switch OFF. BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT-III and various settings.
INFOID:0000000000994419
BCS-6
2007 Altima
[BCM]
A
Warning function Key reminder function Engine start function Power window system RAP (retained accessory power) system TPMS (tire pressure monitior system)
L
ALCIA0020ZZ
1.
BCM
BCS
BCS-7
2007 Altima
JPMIA0083GB
System Description
OUTLINE
INFOID:0000000000994422
BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the status of each switch. BCM is a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a maximum of 20 switch status.
JPMIA0066GB
OUTPUT 2 FR WASHER
BCS-8
2007 Altima
[BCM]
OUTPUT 5 TAIL LAMP
F
JPMIA0067GB
NOTE: BCM reads the status of the combination switch at 60ms interval when BCM is controlled at low power consumption mode. BCM operates as follows and judges the status of the combination switch. INPUT 1 - 5 outputs the voltage waveforms of 5 systems simultaneously. It operates the transistor on OUTPUT side in the following order: OUTPUT 5 4 3 2 1. The voltage waveform of INPUT corresponding to the formed circuit changes according to the operation of the transistor on OUTPUT side if any (1 or more) switches are ON. It reads this change of the voltage as the status signal of the combination switch.
BCS
P
JPMIA0068GB
Operation Example In the following operation example, the combination of the status signals of the combination switch is replaced as follows: INPUT 1 - 5 to 1 - 5 and OUTPUT 1 - 5 to A - E.
Example 1: When a switch (TURN RH switch) is turned ON
BCS-9
2007 Altima
JPMIA0073GB
BCM detects the combination switch status signal 1E when the signal of OUTPUT 5 is input to INPUT 1. BCM judges that the TURN RH switch is ON when the signal 1E is detected. Example 2: When some switches (TURN RH switch, FR WIPER LOW switch) are turned ON
Example 2: When some switches (turn RH switch, front wiper LO switch) are turned ON
The circuits between INPUT 1 and OUTPUT 5 and between INPUT 1 and OUTPUT 3 are formed when the TURN RH switch and FR WIPER LOW switch are turned ON.
JPMIA0074GB
BCM detects the combination switch status signal 1CE when the signals of OUTPUT 3 and OUTPUT 5 are input to INPUT 1. BCM judges that the TURN RH switch and FR WIPER LOW switch are ON when the signal 1CE is detected.
BCS-10
2007 Altima
[BCM]
A
BCS
BCS-11
2007 Altima
JPMIA0070GB
System Description
OUTLINE
INFOID:0000000000994424
BCM has the signal transmission function that outputs/transmits each input/received signal to each unit.
BCS-12
2007 Altima
ALCIA0030GB
System Description
OUTLINE
INFOID:0000000000994426
BCM incorporates a power saving control function that reduces the power consumption according to the vehicle status. BCM switches the status (control mode) by itself with the power saving control function. It performs the sleep request to each unit (IPDM E/R and combination meter) that operates with the ignition switch OFF.
Normal mode (wake-up)
- CAN communication is normally performed with other units - Each control with BCM is operating properly
CAN communication sleep mode (CAN sleep)
BCS
BCS-13
2007 Altima
[BCM]
BCM sleep condition
CAN sleep condition Receiving the sleep-ready signal (ready) from all units Ignition switch: OFF Vehicle security system alarm and panic alarm : No operation Warning lamp: Not operation Intelligent Key system buzzer: No operation Trunk room lamp switch status: No change Brake switch: OFF Key slot status: No change Turn signal indicator lamp: No operation Exterior lamp: OFF Door lock status: No change CONSULT-III communication status: No communication Meter display signal : Non-transmission Electronic steering column lock operation: No operation Door switch status: No change Rear window defogger: OFF
Interior room lamp battery saver: Time out RAP system: OFF Power window switch communication: No transmission Push-button ignition switch (push switch) illumination: OFF NATS: No operation Remote keyless entry receiver communication status: No communication Tire pressure monitor system: Stop
Wake-up operation
BCM changes from the low power consumption mode to the CAN communication sleep mode when the any of the BCM wake-up conditions is fulfilled. Only the control with BCM is activated. BCM transmits the sleep wake up signal (wake up) to each unit when any of the CAN wake-up conditions is fulfilled. It changes from the low power consumption mode or the CAN communication sleep mode to the normal mode. Each unit starts the transmission of CAN communication with the sleep wake up signal. In addition, the combination meter transmits the wake up signal to BCM via CAN communication to report the CAN communication start.
Wake-up condition
CAN wake-up condition Receiving the sleep-ready signal (Not-ready) from any units Key slot: OFFON, ONOFF Push-button ignition switch (push switch): OFFON Hazard switch: OFFON PASSING switch: OFFON, ONOFF TAIL LAMP switch: OFFON Driver door switch: OFFON, ONOFF Passenger door switch: OFF ON, ON OFF Rear RH door switch: OFFON, ONOFF Rear LH door switch: OFFON, OFFON Trunk room lamp switch: OFFON, ONOFF Driver door request switch: OFFON Passenger door request switch: OFFON Trunk request switch: OFFON Stop lamp switch 2 signal: ON Clutch interlock switch: OFFON
INFOID:0000000000994427
Trunk lid opener switch: OFFON Power window switch communication: Receiving Remote keyless entry receiver: Receiving
BCS-14
2007 Altima
ALCIA0022ZZ
1.
Combination meter
3.
IPDM E/R
BCS
BCS-15
2007 Altima
SYSTEM APPLICATION
BCM can perform the following functions for each system. NOTE: It can perform the diagnosis modes except the following for all sub system selection items.
System Door lock Rear window defogger Warning chime Interior room lamp timer Exterior lamp Wiper and washer Turn signal and hazard warning lamps Air conditioner Intelligent Key system Combination switch BCM Immobilizer Interior room lamp battery saver Trunk open Vehicle security system RAP system Signal buffer system TPMS Sub system selection item DOOR LOCK REAR DEFOGGER BUZZER INT LAMP EXTERNAL LAMP WIPER FLASHER AIR CONDITONER INTELLIGENT KEY COMB SW BCM IMMU BATTERY SAVER TRUNK THEFT ALM RETAINED PWR SIGNAL BUFFER AIR PRESSURE MONITOR
INFOID:0000000000994429
SELF-DIAG RESULT
Refer to BCS-72, "DTC Index".
BUZZER
Revision: October 2006
BCS-16
2007 Altima
DATA MONITOR
Display item [Unit] VEH SPEED 1 [Km/h] PUSH SW [On/Off] UNLK SEN -DR [On/Off] KEY SW-SLOT [On/Off] TAIL LAMP SW [On/Off] FR FOG SW [On/Off] DOOR SW -DR [On/Off] Description Value of vehicle speed signal received from ABS actuator and electric unit (control unit) with CAN communication line. Status of push button ignition switch judged by BCM. Status of unlock sensor judged by BCM. Status of key slot judged by BCM.
G
Status of each switch judged by BCM using the combination SW readout function. Status of front fog lamp switch judged by BCM. Status of driver side door switch judged by BCM.
ACTIVE TEST
Display item [Unit] IGN KEY WARN ALM SEAT BELT WARN TEST ID REGIST WARNING LIGHT WARN ALM Description The key warning chime operation can be checked by operating the relevant function (On/Off). The seat belt warning chime operation can be checked by operating the relevant function (On/Off). The ID regist warning chime operation can be checked by operating the relevant function (On/Off). The light warning chime operation can be checked by operating the relevant function (On/Off).
INT LAMP
INT LAMP : CONSULT-III Function
WORK SUPPORT
N
INFOID:0000000000994431
BCS
JPLIA0093GB
BCS-17
2007 Altima
[BCM]
* : Initial setting
DATA MONITOR
Monitor item [Unit] REQ SW-DR [ON/OFF] REQ SW-AS [ON/OFF] PUSH SW [ON/OFF] ACC RLY-F/B [ON/OFF] KEY SW-SLOT [ON/OFF] DOOR SW-DR [ON/OFF] DOOR SW-AS [ON/OFF] DOOR SW-RR [ON/OFF] DOOR SW- RL [ON/OFF] DOOR SW-BK [ON/OFF] CDL LOCK SW [ON/OFF] CDL UNLOCK SW [ON/OFF] Description The switch status input from request switch (driver side) The switch status input from front request switch (passenger side) The switch status input from push-button ignition switch ACC relay feedback signal status input from ACC relay Key switch status input from key slot The switch status input from front door switch (driver side) The switch status input from front door switch (passenger side) The switch status input from rear door switch RH The switch status input from rear door switch LH NOTE: The item is indicated, not monitored. Lock switch status received from central door lock switch by power window switch serial link Unlock switch status received from central door lock switch by power window switch serial link
- 1 8
2007 Altima
[BCM]
A
ACTIVE TEST
Test item INT LAMP Operation ON OFF STEP LAMP TEST ON OFF ON OFF Description Outputs the interior room lamp control signal to turn map lamp and personal lamp ON (Map lamp switch is in DOOR position). Stops the interior room lamp control signal to turn map lamp and personal lamp OFF. Outputs the step lamp control signal to turn step lamp ON. Stops the step lamp control signal to turn step lamp OFF. Outputs the luggage room lamp control signal to turn step lamp ON. Stops the luggage room lamp control signal to turn step lamp ON.
EXTERNAL LAMP
EXTERNAL LAMP : CONSULT-III Function
WORK SUPPORT
Service item BATTERY SAVER SET Setting item ON* OFF MODE 1* MODE 2 MODE 3 ILL DELAY SET MODE 4 MODE 5 MODE 6 MODE 7 MODE 8 MODE 1* CUSTOM A/LIGHT SETTING MODE 2 MODE 3 MODE 4 * : Initial setting Setting With the exterior lamp battery saver function Without the exterior lamp battery saver function 45 sec. Without the function 30 sec. 60 sec. 90 sec. 120 sec. 150 sec. 180 sec. Normal More sensitive setting than normal setting (Turns ON earlier than normal operation.) More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.) Less sensitive setting than normal setting (Turns ON later than normal operation.) Sets delay timer function timer operation time (All doors closed)
INFOID:0000000000994432
BCS
DATA MONITOR
BCS-19
2007 Altima
[BCM]
ACTIVE TEST
Test item TAIL LAMP Operation ON OFF HI HEAD LAMP LO OFF Description Transmits the Position light request signal to IPDM E/R with CAN communication to turn the tail lamp ON. Stops the tail lamp request signal transmission. Transmits the high beam request signal with CAN communication to turn the headlamp (HI) Transmits the low beam request signal with CAN communication to turn the headlamp (LO). Stops the high & low beam request signal transmission.
BCS-20
2007 Altima
[BCM]
A
WIPER
WIPER : CONSULT - III Function
WORK SUPPORT
Service item WIPER SPEED SETTING * : Factory setting Setting item ON OFF* Description With vehicle speed (Front wiper intermittent time linked with the vehicle speed and wiper dial position) Without vehicle speed (Front wiper intermittent time linked with the wiper dial position)
INFOID:0000000000994433
DATA MONITOR
Monitor Item [Unit] PUSH SW VEH SPEED 1 [km/h] FR WIPER HI [OFF/ON] FR WIPER LOW [OFF/ON] FR WASHER SW [OFF/ON] FR WIPER INT [OFF/ON] FR WIPER STOP [OFF/ON] INT VOLUME [1 7] Displays the status of the front wiper auto stop signal received from IPDM E/R with CAN communication. Status of each switch judged by BCM using the combination switch reading function Description Displays the status of the engine switch (push switch) judged by BCM. Displays the value of the vehicle speed signal received from combination meter with CAN communication.
L
Status of each switch judged by BCM using the combination switch reading function
BCS
ACTIVE TEST
P
BCS-21
2007 Altima
[BCM]
FRONT WIPER
FLASHER
FLASHER : CONSULT-III Function
Work support
Service item Setting item LOCK ONLY* HAZARD ANSWER BACK UNLK ONLY LOCK/UNLK OFF * : Initial setting Activated when locking. Activated when unlocking. Activated when locking/ unlocking Not activated Sets the hazard warning lamp answer back activation when the door is lock/unlock with the request switch or the key fob. Setting
INFOID:0000000000994434
Data monitor
Monitor item [Unit] TURN SIGNAL [ON/OFF] TURN SIGNAL L [ON/OFF] HAZARD SW [ON/OFF] RKE LOCK [ON/OFF] RKE UNLOCK [ON/OFF] RKE PANIC [ON/OFF] Description
Each switch condition that BCM judges from the combination switch reading function
The switch status input from the hazard warning switch The lock signal status received from the keyless receiver The unock signal status received from the keyless receiver The panic alarm signal status received from the keyless receiver
Active test
Test item Operation RH FLASHER LH OFF Blinks right turn signal lamp. Blinks left turn signal lamp. Turns turn signal lamps (right and left) OFF. Description
COMB SW
COMB SW : CONSULT-III Function
DATA MONITOR
INFOID:0000000000994435
BCS-22
2007 Altima
[BCM]
A
BCS
BATTERY SAVER
BATTERY SAVER : CONSULT-III Function
WORK SUPPORT
Service item BATTERY SAVER SET Setting item ON* OFF ON* OFF MODE 1* MODE 2 Setting With the exterior lamp battery saver function Without the exterior lamp battery saver function With the interior room lamp battery saver function Without the interior room lamp battery saver function 30 min. 60 min. Sets the interior room lamp battery saver timer operating time.
INFOID:0000000000994437
BCS-23
2007 Altima
[BCM]
DATA MONITOR
Monitor item [Unit] REQ SW-DR [ON/OFF] REQ SW-AS [ON/OFF] PUSH SW [ON/OFF] ACC RLY-F/B [ON/OFF] KEY SW-SLOT [ON/OFF] DOOR SW-DR [ON/OFF] DOOR SW-AS [ON/OFF] DOOR SW-RR [ON/OFF] DOOR SW- RL [ON/OFF] DOOR SW-BK [ON/OFF] CDL LOCK SW [ON/OFF] CDL UNLOCK SW [ON/OFF] KEY CYL LK-SW [ON/OFF] KEY CYL UN-SW [ON/OFF] TRNK/HAT MNTR [ON/OFF] RKE-LOCK [ON/OFF] RKE-UNLOCK [ON/OFF] Description The switch status input from request switch (driver side) The switch status input from front request switch (passenger side) The switch status input from push-button ignition switch ACC relay feedback signal status input from ACC relay Key switch status input from key slot The switch status input from front door switch (driver side) The switch status input from front door switch (passenger side) The switch status input from rear door switch RH The switch status input from rear door switch LH NOTE: The item is indicated, not monitored. Lock switch status received from central door lock switch by power window switch serial link Unlock switch status received from central door lock switch by power window switch serial link Lock switch status received from key cylinder switch by power window switch serial link Unlock switch status received from key cylinder switch by power window switch serial link The switch status input from trunk room lamp switch Lock signal status received from remote keyless entry receiver Unlock signal status received from remote keyless entry receiver
ACTIVE TEST
Test item BATTERY SAVER Operation OFF ON Description Cuts the interior room lamp power supply to turn interior room lamp OFF. Outputs the interior room lamp power supply to turn interior room lamp ON.*
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT-III Function
DATA MONITOR
INFOID:0000000000994438
BCS-24
2007 Altima
[BCM]
A
ACTIVE TEST
Test item Operation OFF OIL PRESSURE SW ON OFF BCM transmits the oil pressure switch signal to the combination meter via CAN communication, which illuminates the oil pressure warning lamp.
BCS
SEIA0745E
NOTE: When the low tire warning lamp flashes 5 Hz and continues repeating it, the system is normal.
Flickering pattern 15 16 17 18 21 22 23 24 Items Tire pressure value (Front LH) Tire pressure value (Front RH) Tire pressure value (Rear RH) Tire pressure value (Rear LH) Transmitter no data (Front LH) Transmitter no data (Front RH) Transmitter no data (Rear RH) Transmitter no data (Rear LH) Diagnostic items detected when Front LH tire pressure drops to 181 kPa (1.8 kg/cm, 26 psi) or less. Front RH tire pressure drops to 181 kPa (1.8 kg/cm, 26 psi) or less. Rear RH tire pressure drops to 181 kPa (1.8 kg/cm, 26 psi) or less. Rear LH tire pressure drops to 181 kPa (1.8 kg/cm, 26 psi) or less. Data from front LH transmitter can not be received. Data from front RH transmitter can not be received. Data from Rear RH transmitter can not be received. Data from Rear LH transmitter can not be received. WT-20 Check item
BCS-25
2007 Altima
[BCM]
Check item
ERASE SELF-DIAGNOSIS
1. 2.
With CONSULT-III Perform applicable inspection of malfunctioning item and then repair or replace. Turn ignition switch ON and select SELF-DIAG RESULTS mode for AIR PRESSURE MONITOR with CONSULTIII. 3. Touch ERASE on CONSULT-III screen to erase memory.
Without CONSULT-III In order to make it easier to find the cause of hard-to-duplicate malfunctions, malfunction information is stored into the control unit as necessary during use by the user. This memory is not erased no matter how many times the ignition switch is turned ON andOFF. However, this information is erased by turning ignition switch OFF after performing self-diagnostic or by erasing the memory using the CONSULT-III.
INFOID:0000000000994440
BCS-26
2007 Altima
[BCM]
A
BCS
BCS-27
2007 Altima
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description
Refer to LAN-7, "System Description".
INFOID:0000000000994441
DTC Logic
DTC DETECTION LOGIC
CONSULT-III display description DTC Detection Condition Possible cause
INFOID:0000000000994442
When IPDM E/R cannot communicate CAN communication signal continuously for 2 seconds or more
In CAN communication system, any item (or items) of the following listed below is malfunctioning. Transmission Receiving (ECM) Receiving (VDC/TCS/ABS) Receiving (METER/M&A) Receiving (TCM) Receiving (MULTI AV) Receiving (IPDM E/R)
INFOID:0000000000994443
Diagnosis Procedure
BCS-28
2007 Altima
Diagnosis Procedure
D
INFOID:0000000000994445
1. REPLACE BCM
When DTC U1010 is detected, replace BCM. >> Replace BCM. Refer to BCS-76, "Removal and Installation".
BCS
BCS-29
2007 Altima
U0415 is displayed if any unusual condition is present in the reception status of the vehicle speed signal from the ABS actuator and electric unit (control unit).
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III VEHICLE SPEED SIG [U0415] Diagnostic item is detected when ...
INFOID:0000000000994447
U0415
When the vehicle speed signal received from ABS actuator and electric unit (control unit) the ABS actuator and electric unit (control BCM unit) remains abnormal for 2 seconds or more.
1. DTC CONFIRMATION
1. 2. 3. Erase the DTC. Turn ignition switch OFF. Perform the "SELF-DIAG RESULTS" of CONSULT-III, when passed 2 seconds or more after the ignition switch is turned ON Is any DTC detected? YES >> Refer to BCS-72, "DTC Index". NO >> Inspection End.
Diagnosis Procedure
INFOID:0000000000994448
BCS-30
2007 Altima
1. DTC CONFIRMATION
Erase DTC. Turn ignition switch OFF. Perform the "SELF-DIAG RESULTS" of CONSULT-III, when passed 1.5 seconds or more after ignition switch is turned ON. Is any DTC detected? YES >> Refer to BCS-31, "Diagnosis Procedure". NO >> Inspection End. 1. 2. 3.
E F
Diagnosis Procedure
INFOID:0000000000994450
INFOID:0000000000994451
BCS
BCS-31
2007 Altima
B2563 HI VOLTAGE
< COMPONENT DIAGNOSIS > [BCM]
B2563 HI VOLTAGE
DTC Logic
DTC DETECTION LOGIC
DTC B2563 Display contents of CONSULT-III HI VOLTAGE Diagnostic item is detected when ... When the power supply voltage to BCM remains more than 18 V for 90 seconds or more Possible cause Harness or connector (power supply circuit)
INFOID:0000000000994452
1. DTC CONFIRMATION
Erase DTC. Turn ignition switch OFF. Perform the "SELF-DIAG RESULTS" of CONSULT-III, when passed 90 seconds or more after the ignition switch is turned ON. Is any DTC detected? YES >> Refer to BCS-32, "Diagnosis Procedure". NO >> Inspection End. 1. 2. 3.
Diagnosis Procedure
INFOID:0000000000994453
INFOID:0000000000994454
BCS-32
2007 Altima
Is the fuse or fusible link blown? YES >> Replace the blown fuse or fusible link after repairing the affected circuit. NO >> GO TO 2..
G
() Voltage (Approx.)
Is the measurement normal? YES >> GO TO 3.. NO >> Repair or replace harness.
Continuity Existed
Does continuity exist? YES >> Inspection End NO >> Repair or replace harness.
ALCIA0024ZZ
BCS
INFOID:0000000000994456
BCS-33
2007 Altima
Continuity
Is the measurement normal? YES >> GO TO 4. NO >> Replace BCM. Refer to BCS-76, "Removal and Installation".
Revision: October 2006
BCS-34
2007 Altima
Is the measurement normal when any of the switches is turned ON? YES >> Replace BCM. Refer to BCS-76, "Removal and Installation". NO >> Replace the combination switch. Refer to EXL-130, "Removal and Installation".
G
INFOID:0000000000994458
BCS
BCS-35
2007 Altima
Continuity
OUTPUT 5
8 1.4 V
JPMIA0041GB
BCS-36
2007 Altima
INFOID:0000000000994460
BCS
BCS-37
2007 Altima
ECU DIAGNOSIS
BCM (BODY CONTROL MODULE)
Reference Value
VALUES ON THE DIAGNOSIS TOOL
Monitor Item FR WIPER HI Condition Other than front wiper switch HI Front wiper switch HI Other than front wiper switch LO Front wiper switch LO Front washer switch OFF Front washer switch ON Other than front wiper switch INT Front wiper switch INT Front wiper is not in STOP position Front wiper is in STOP position Wiper intermittent dial is in a dial position 1 - 7 Other than turn signal switch RH Turn signal switch RH Other than turn signal switch LH Turn signal switch LH Other than lighting switch 1ST and 2ND Lighting switch 1ST or 2ND Other than lighting switch HI Lighting switch HI Other than lighting switch 2ND Lighting switch 2ND Other than lighting switch 2ND Lighting switch 2ND Other than lighting switch PASS Lighting switch PASS Other than lighting switch AUTO Lighting switch AUTO Front fog lamp switch OFF Front fog lamp switch ON Driver door closed Driver door opened Passenger door closed Passenger door opened Rear RH door closed Rear RH door opened Rear LH door closed Rear LH door opened OFF ON OFF ON OFF ON OFF ON OFF ON Wiper intermittent dial position OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON Value/Status
INFOID:0000000000994461
FR WIPER LOW
FR WASHER SW
FR WIPER INT
TURN SIGNAL L
TAIL LAMP SW
HI BEAM SW
HEAD LAMP SW 1
HEAD LAMP SW 2
PASSING SW
AUTO LIGHT SW
FR FOG SW
DOOR SW-DR
DOOR SW-AS
DOOR SW-RR
DOOR SW-RL
BCS-38
2007 Altima
[BCM]
A
CDL UNLOCK SW
KEY CYL UN-SW KEY CYL SW-TR HAZARD SW REAR DEF SW FAN ON SIG AIR COND SW TR CANCEL SW
TR/BD OPEN SW
TRNK/HAT MNTR
RKE-LOCK
RKE-UNLOCK
RKE-TR/BD
RKE-PANIC
RKE-P/W OPEN
BCS
RKE-MODE CHG
REQ SW-AS
REQ SW-BD/TR
BCS-39
2007 Altima
[BCM]
CLUTCH SW
BRAKE SW 1
DETE/CANCL SW
SFT PN/N SW
S/L -LOCK
S/L -UNLOCK
S/L RELAY-F/B
UNLK SEN-DR
PUSH SW -IPDM
DETE SW -IPDM
SFT PN -IPDM
SFT P -MET
SFT N -MET
S/L UNLOCK-IPDM
S/L RELAY-REQ
BCS-40
2007 Altima
[BCM]
A
PRMT ENG STAT PRMT RKE STAT KEY SW -SLOT RKE OPE COUN1 RKE OPE COUN2 AIR PRESS FL AIR PRESS FR AIR PRESS RR AIR PRESS RL ID REGST FL1
J
Air pressure of rear LH tire DONE YET DONE YET DONE YET DONE YET OFF ON OFF ON
INFOID:0000000000994462
ID REGST FR1
ID REGST RR1
BCS
ID REGST RL1
WARNING LAMP
BUZZER
Terminal Layout
BCS-41
2007 Altima
ALCIA0023ZZ
Physical Values
INFOID:0000000000994463
BCS-42
2007 Altima
[BCM]
A
Ignition switch OFF Ignition switch OFF Ignition switch ON After passing the interior room lamp battery saver operation time Any other time after passing the interior room lamp battery saver operation time UNLOCK (actuator is activated) Other than UNLOCK (actuator is not activated) ON OFF LOCK (actuator is activated) Other than LOCK (actuator is not activated) UNLOCK (actuator is activated) Other than UNLOCK (actuator is not activated) UNLOCK (actuator is activated) Other than UNLOCK (actuator is not activated)
Ground
Output
E
Battery voltage 0V 0V Battery voltage Battery voltage 0V Battery voltage 0V Battery voltage 0V
5 (G/Y)
Ground
Output
Front door RH
7 (R/W)
Ground
Step lamp
Output
Step lamp
8 (V)
Ground
Output
All doors
9 (G)
Ground
Output
Front door LH
Ground
Rear door RH and rear door LH UNLOCK Battery power supply Ground
Output
K
Battery voltage 0V
Ground Ground
Input
BCS
14 (R/Y)
Ground
Input
Tail lamp
N
ON
O
JSNIA0010GB
15 (Y/L)
Ground
Output
Ignition switch
OFF ACC or ON
Battery voltage 0V
BCS-43
2007 Altima
[BCM]
17 (G/B)
Ground
Output
Ignition switch ON
PKID0926E
18 (G/Y)
Ground
Output
Ignition switch ON
PKID0926E
6.5 V 19 (Y) Ground Room lamp timer control Output Interior room lamp OFF ON When outside of the vehicle is bright When outside of the vehicle is dark OFF (clutch pedal is not depressed) ON (clutch pedal is depressed) OFF (brake pedal is not depressed) ON (brake pedal is depressed) OFF ON Battery voltage 0V Close to 5V Close to 0V 0V Battery voltage Battery voltage 0V Battery voltage 0V Battery voltage
21 (P/B)
Ground
Input
Ignition switch ON
22 (R/Y) 24 (R/W)
Ground
Input
Ground
Input
Stop lamp switch 26 (O/L) Ground Stop lamp switch 2 Input ICC brake hold relay (with ICC)
27 (G/W)
Ground
Input
Front door LH
LOCK status
JPMIA0011GB
11.8V UNLOCK status 29 (Y) Ground Key slot switch Input When Intelligent Key is inserted into key slot When Intelligent Key is not inserted into key slot 0V Battery voltage 0V
BCS-44
2007 Altima
[BCM]
A
Ground
Input
D
32 (R/B) Ground Front door RH switch Input Front door RH switch OFF (when front door RH closes)
E
JPMIA0011GB
11.8 V ON (when front door RH opens) 33 (SB) 34 (L/R) 36 (GR) Ground Compressor ON signal Front door lock assembly LH (key cylinder switch) (unlock) Lock switch signal Input A/C switch Front door lock assembly LH (key cylinder switch) Door lock/unlock switch OFF ON OFF (neutral) ON (unlock) Lock Unlock 0V 5V 0V 5V 0V Battery voltage 0V
Ground
Input
Ground
Input
J
37 (O) Ground Trunk lid opener cancel switch Input Trunk lid opener cancel switch CANCEL
JPMIA0012GB
1.1V ON 38 (GR/ W) 39 (GR/ R) Ground Rear window defogger ON signal Input Rear window defogger switch Door lock/unlock switch OFF ON Unlock Lock 0V 5V 0V Battery voltage 0V
BCS
Ground
Input
40 (Y/G)
Ground
Input/ Output
Ignition switch ON
JPMIA0013GB
10.2V Ignition switch OFF or ACC 41 (W) Engine switch (push switch) illumination Engine switch (push switch) illumination ON 0V 5.5V
Ground
Output
OFF
0V
BCS-45
2007 Altima
[BCM]
Standby state
OCC3881D
47 (G/O)
Ground
Input/ Output
Ignition switch ON
OCC3880D
48 (R/G)
Ground
Input
Selector lever
12.0V 0V 0V
49 (L/O)
Ground
Output
Security indicator
Blinking
JPMIA0014GB
11.3V OFF All switch OFF Lighting switch 1ST 50 (LG/ B) Combination switch (Wiper intermittent dial 4) Lighting switch high-beam Lighting switch 2ND Battery voltage 0V
Ground
Output
10.7V
BCS-46
2007 Altima
[BCM]
A
D
JPMIA0032GB
10.7V
E
0V
G
JPMIA0033GB
Ground
Output
J
Lighting switch AUTO
JPMIA0034GB
10.7V All switch OFF Front fog lamp switch ON Combination switch (Wiper intermittent dial 4) Lighting switch 2ND Lighting switch flash-topass 0V
54 (G/Y)
Ground
Output
BCS
10.7V 55 (BR/ W) 56 (L/B) 57 (W) Ground Front blower monitor Front door lock assembly LH (key cylinder switch) (lock) Tire pressure warning check switch Input Front blower motor switch Front door lock assembly LH (key cylinder switch) ON OFF OFF (neutral) ON (lock) Battery voltage 0V 5V 0V 5V
Ground
Input
Ground
Input
BCS-47
2007 Altima
[BCM]
58 (SB)
Ground
Input
JPMIA0011GB
11.8V ON (front door LH OPEN) 59 (G/R) Ground Rear window defogger relay Output Rear window defogger Active Not activated 0V Battery voltage 0V
60 (B/R)
Ground
Output
61 (W/R)
Ground
Output
BCS-48
2007 Altima
[BCM]
A
B
When Intelligent Key is in the antenna detection area
62 (B/Y)
Ground
Output
When the front door RH request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0062GB
F
JMKIA0063GB
63 (LG)
Ground
Output
When the front door RH request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0062GB
K
JMKIA0063GB
BCS
When Intelligent Key is in the antenna detection area
N
64 (V) Front outside handle LH antenna (-) When the front door LH request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0063GB JMKIA0062GB
Ground
Output
BCS-49
2007 Altima
[BCM]
65 (P)
Ground
Output
When the front door LH request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0062GB
JMKIA0063GB
66 (R)
Ground
Output
67 (G)
Ground
Output
BCS-50
2007 Altima
[BCM]
A
Ground
During waiting
Ground
Ignition switch
E
During waiting
F
JMKIA0064GB
71 (L/O)
Ground
Input/ Output
H
When operating either button on Intelligent Key
JMKIA0065GB
J
All switch OFF (Wiper intermittent dial 4)
K
JPMIA0041GB
1.4V
BCS
75 (R/Y) Ground Combination switch INPUT 5 Input Combination switch Front fog lamp switch ON (Wiper intermittent dial 4)
N
JPMIA0037GB
1.3V
O
Any of the conditions below with all switch OFF Wiper intermittent dial 1 Wiper intermittent dial 2 Wiper intermittent dial 6 Wiper intermittent dial 7
JPMIA0040GB
1.3V
BCS-51
2007 Altima
[BCM]
JPMIA0041GB
1.4V
JPMIA0036GB
76 (R/G)
Ground
Input
Combination switch
1.3V
JPMIA0037GB
1.3V
Any of the conditions below with all switch OFF Wiper intermittent dial 1 Wiper intermittent dial 2 Wiper intermittent dial 3
JPMIA0040GB
1.3V 77 (BR) 78 (P) 79 (L) Ground Ground Ground Engine switch (push switch) CAN-L CAN-H Input Input/ Output Input/ Output Engine switch (push switch) Pressed Not pressed OFF 0V 0V Battery voltage
80 (R/L)
Ground
Output
Blinking
JPMIA0015GB
BCS-52
2007 Altima
[BCM]
A
Ground Ground
ACC relay control A/T device Electronic steering column lock condition No. 1 Electronic steering column lock condition No. 2 Selector lever P position switch
Output Output
Ignition switch
Ground
Input
Ground
Input
Ground
Input
G
88 (P/L) Front door RH request switch Front door RH request switch
Ground
Input
JPMIA0016GB
1.0V ON (pressed) 0V
89 (B/W)
Ground
Input
JPMIA0016GB
1.0V 90 (Y) 91 (L/R) 94 (G/Y) Ground Blower fan motor relay control Remote keyless entry receiver power supply Steering wheel lock unit power supply Output Ignition switch OFF or ACC ON 0V Battery voltage Battery voltage
BCS
Ground
Output
N
Output Ignition switch Battery voltage 0V
Ground
BCS-53
2007 Altima
[BCM]
JPMIA0041GB
1.4V
JPMIA0037GB
1.3V
95 (R/W)
Ground
Input
JPMIA0036GB
1.3V
JPMIA0038GB
1.3V
JPMIA0039GB
1.3V
BCS-54
2007 Altima
[BCM]
A
B
All switch OFF (Wiper intermittent dial 4)
JPMIA0041GB
1.4V
E
Lighting switch AUTO (Wiper intermittent dial 4)
F
JPMIA0038GB
96 (P/B)
Ground
Input
Combination switch
1.3V
JPMIA0036GB
1.3V
J
Any of the conditions below with all switch OFF Wiper intermittent dial 1 Wiper intermittent dial 5 Wiper intermittent dial 6
JPMIA0039GB
1.3V
BCS
BCS-55
2007 Altima
[BCM]
JPMIA0041GB
1.4V
JPMIA0037GB
1.3V
97 (R/B)
Ground
Input
JPMIA0036GB
1.3V
JPMIA0038GB
1.3V
JPMIA0040GB
1.3V Pressed 0V
98 (G/O)
Ground
Hazard switch
Input
Hazard switch
Not pressed
JPMIA0012GB
1.1V
BCS-56
2007 Altima
[BCM]
A
C
99 (L/Y) Ground Electronic steering column lock unit communication LOCK or UNLOCK Input/ Output Electronic steering column lock
JMKIA0066GB
For 15 seconds after UNLOCK 15 seconds or later after UNLOCK 103 (V) Open (trunk lid opener actuator is activated) Close (trunk lid opener actuator is not activated) ON OFF
Battery voltage 0V
F
Battery voltage 0V 0V Battery voltage
Ground
Output
Trunk lid
110 (V/W)
Ground
Output
J
114 (B) Ground Trunk room antenna 1 (-) Output Ignition switch OFF
K
When Intelligent Key is not in the passenger compartment
JMKIA0063GB
BCS
BCS-57
2007 Altima
[BCM]
115 (W)
Ground
Output
118 (L/O)
Ground
Output
When the trunk lid request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0062GB
JMKIA0063GB
119 (BR/ W)
Ground
Output
When the trunk lid request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0062GB
JMKIA0063GB
BCS-58
2007 Altima
[BCM]
A
129 (Y/G)
Ground
Input
D
JPMIA0011GB
11.8V ON (trunk is open) Ignition switch OFF (M/T vehicle) 131 (R) Ground Starter motor relay control Output Ignition switch ON (other than M/ T vehicle) When the clutch pedal is depressed When the clutch pedal is not depressed When selector lever is in P or N position and the brake is depressed When selector lever is in P or N position and the brake is not depressed ON (pressed) 0V Battery voltage 0V
G
Battery voltage
H
0V 0V
141 (G/R)
Ground
Input
J
OFF (not pressed)
K
JPMIA0016GB
1.0V 144 (GR) Ground Request switch buzzer Output Request switch buzzer Sounding Not sounding Pressed 0V Battery voltage 0V
BCS
147 (L/R)
Ground
Input
N
Not pressed
JPMIA0011GB
11.8V
BCS-59
2007 Altima
[BCM]
148 (R/W)
Ground
Input
JPMIA0011GB
149 (R/B)
Ground
Input
JPMIA0011GB
BCS-60
2007 Altima
Wiring Diagram
BCS
O
ALMWA0021GB
BCS-61
2007 Altima
ALMWA0022GB
BCS-62
2007 Altima
BCS
O
ALMWA0023GB
BCS-63
2007 Altima
ALMWA0024GB
BCS-64
2007 Altima
BCS
O
ALMWA0025GB
BCS-65
2007 Altima
ALMWA0026GB
BCS-66
2007 Altima
BCS
O
ALMIA0060GB
BCS-67
2007 Altima
ALMIA0061GB
BCS-68
2007 Altima
BCS
O
ALMIA0062GB
Fail Safe
Display contents of CONSULT B2013: ID DISCORD BCM-S/L B2014: CHAIN OF S/L-BCM B2190: NATS ANTTENA AMP Fail-safe Inhibit engine cranking Inhibit engine cranking Inhibit engine cranking Erase DTC Erase DTC Erase DTC Cancellation
INFOID:0000000000994465
BCS-69
2007 Altima
[BCM]
B2562: LO VOLTAGE
Inhibit engine cranking Inhibit electronic steering column lock Inhibit engine cranking Inhibit electronic steering column lock Inhibit electronic steering column lock
B2563: HI VOLTAGE
500 ms after the power supply voltage decreases to less than 18 V 500 ms after the following signal reception status becomes consistent Selector lever P position switch signal P range signal (CAN) 5 seconds after the following BCM recognition conditions are fulfilled Ignition switch is in the ON position Selector lever P position switch signal: Except P position (battery voltage) Vehicle speed: 4 /h or more 500 ms after the following BCM recognition conditions are fulfilled Ignition switch is in the ON position Selector lever P position switch signal: Except P position (battery voltage) Selector lever P/N position signal: Except P and N positions (0 V) 500 ms after any of the following BCM recognition conditions is fulfilled Status 1 - Ignition switch is in the ON position - Selector lever P/N position signal: P and N position (battery voltage) - P range signal or N range signal (CAN): ON Status 2 - Ignition switch is in the ON position - Selector lever P/N position signal: Except P and N positions (0 V) - P range signal and N range signal (CAN): OFF 500 ms after any of the following BCM recognition conditions is fulfilled Ignition switch is in the ON position - Power position: IGN - Selector lever P/N position signal: Except P and N positions (0 V) - Interlock/PNP switch signal (CAN): OFF Status 2 - Ignition switch is in the ON position - Selector lever P/N position signal: P or N position (battery voltage) - PNP switch signal (CAN): ON 500 ms after the following CAN signal communication status has become consistent Electronic steering column lock relay signal (Request signal) Electronic steering column lock relay signal (Condition signal)
B2604: PNP SW
B2605: PNP SW
BCS-70
2007 Altima
[BCM]
A
Maintains the power supply position attained at the time of DTC detection
B2617: STARTER RELAY CIRC B2618: BCM B2619: BCM B261E: VEHICLE TYPE B26E1: ENG STATE NO RECIV
Inhibit engine cranking Inhibit engine cranking Inhibit engine cranking Inhibit engine cranking Inhibit engine cranking
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority BCS chart.
Priority 1 2 B2562: LOW VOLTAGE B2563: HI VOLTAGE U1000: CAN COMM CIRCUIT U1010: CONTROL UNIT (CAN) B2190: NATS ANTTENA AMP B2191: DIFFERENCE OF KEY B2192: ID DISCORD BCM-ECM B2193: CHAIN OF BCM-ECM DTC
BCS-71
2007 Altima
[BCM]
DTC Index
Revision: October 2006
BCS-72
2007 Altima
D
PCS-48 PCS-49 BCS-30 SEC-36 SEC-37 SEC-30 SEC-33 SEC-34 SEC-35 PCS-50 SEC-40 SEC-42 SEC-44 SEC-45 BCS-31 BCS-32 SEC-46 SEC-49 SEC-51 SEC-54 SEC-56 SEC-58 SEC-59 SEC-61 SEC-63 PCS-52 SEC-67 SEC-68 SEC-69 SEC-70 PCS-53 SEC-72 PCS-55 PCS-58
BCS
BCS-73
2007 Altima
[BCM]
Reference page PCS-61 SEC-76 PCS-64 SEC-78 SEC-79 SEC-81 DLK-40 DLK-42 DLK-44 SEC-71 WT-19 WT-19 WT-19 WT-19 WT-13 WT-13 WT-13 WT-13 WT-14 WT-14 WT-14 WT-14 WT-15 WT-15 WT-15 WT-15 WT-14 WT-14 WT-14 WT-14 WT-14 WT-14 WT-14 WT-14 WT-16
BCS-74
2007 Altima
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table
1. 2. Perform the data monitor of CONSULT-III to check for any malfunctioning item. Check the malfunction combinations.
Malfunction item:
INFOID:0000000000994468
Data monitor item HEAD LAMP SW 1 HEAD LAMP SW 2 AUTO LIGHT SW FR WASHER SW TURN SIGNAL R TURN SIGNAL L FR WIPER LOW TAIL LAMP SW FR WIPER INT
D
FR FOG SW
Malfunction combination
PASSING SW
FR WIPER HI
INT VOLUME
HI BEAM SW
A B C D E F G H I J K L
H
All Items
If only one item is detected or the item is not applicable to the combinations A to K
3.
Identify the malfunctioning part from the agreed combination and repair or replace the part.
Malfunction combination A B C D E F G H I J K L Malfunctioning part Combination switch INPUT 1 circuit Combination switch INPUT 2 circuit Combination switch INPUT 3 circuit Combination switch INPUT 4 circuit Combination switch INPUT 5 circuit Combination switch OUTPUT 1 circuit Combination switch OUTPUT 2 circuit Combination switch OUTPUT 3 circuit Combination switch OUTPUT 4 circuit Combination switch OUTPUT 5 circuit BCM Combination switch Replace BCM. Refer to BCS-76, "Removal and Installation". Replace the combination switch. Refer to EXL-130, "Removal and Installation". Inspect the combination switch output circuit applicable to the malfunctioning part. BCS-36, "Diagnosis Procedure" Inspect the combination switch input circuit applicable to the malfunctioning part. BCS-34, "Diagnosis Procedure" Repair or replace
BCS
BCS-75
2007 Altima
ON-VEHICLE REPAIR
BCM (BODY CONTROL MODULE)
Removal and Installation
REMOVAL
1. 2. 3. Remove the combination meter. Refer to MWI-64, "Removal and Installation". Remove the BCM screws (A), and pull out the BCM (1). Disconnect the BCM connector and remove the BCM (1).
INFOID:0000000000994469
ALMIA0032ZZ
INSTALLATION
Installation is the reverse order of removal. NOTE: When replacing BCM, it must be configured. Refer to the CONSULT-III operation manual for the initialization procedure. When replacing BCM, perform initialization of the NATS system and registration of all the intelligent ignition key IDs. Refer to the CONSULT-III operation manual for the initialization procedure. When replacing BCM, if new BCM does not come with keyfobs attached, all existing keyfobs must be re-registered.
BCS-76
2007 Altima