Beruflich Dokumente
Kultur Dokumente
COMMERCIAL
y Indianapolis, Indiana
ENGINE
46206
BULLETIN
June 12, 1972 CECO POWER TURBINE GOVERNOR-REPLACE SEAL PLUGS AND SPEED ROTOR SCREEN OR ROTOR AND SCREEN ASSEMBLY AND REWORK OR REPLACE MUSCLES VALVE PLANNING INFORMATION: EFFECTIVITY: REASONS: All Power Turbine Governor Assemblies prior to and including S/N lAAD79. To reduce the possibility of leakage at test and improve filtration, the seven seal plugs are replaced with more positive sealing type plugs. The dimpleretained speed rotor screen is replaced with a spot welded screen and the muscles valve is provided with a bleed hole. This bulletin is written in two parts : disassembly of the power turbine governor and inspection of the pinrotor-shaft assembly and muscles valve; and assembly testing, and reidentification of the power turbine governor. Modification is recommended at next overhaul following availability of parts. FAA-DER approved. No additional man-hours are required at overhaul. AVAILABILITY: New CECO P/N 95872 96027 96445 **96268 Nomenclature Plug Valve, Muscles Rotor and Screen Assy Screen, Speed Rotor 7* 1 1 I
DESCRIPTION
COMMERCIAL
ENGINE
BULLETIN
CECO POWER TURBINE GOVERNOR-REPLACE SEAL PLUGS AND SPEED ROTOR SCREEN OR ROTOR AND SCREEN ASSEMBLY AND REWORK OR REPLACE MUSCLES VALVE
INTERCHANGEABILITY: All ,changes must be accomplished reidentification purposes. TOOLING: WEIGHT None AND BALANCE: None simultaneously for
REFERENCE:
COMMERCIAL
ENGINE
BULLETIN
CECO POWER TURBINE GOVERNOR-REPLACE SEAL PLUGS AND SPEED ROTOR SCREEN OR ROTOR AND SCREEN ASSEMBLY AND REWORK OR REPLACE MUSCLES VALVE ACCOMPLISHMENT PART I. A. INSTRUCTIONS: Inspect Pin-Shaft-
Disassemble the Power Turbine Governor according to the Overhaul Manual. NOTE: Before governor disassembly, inspect the seal plugs installed in the AD, AG, and AL ports (see Figure 1). If P/N 95872 Plugs are installed per 250-C20 CEB-1002, do -- not discard.
1. 2. B.
Discard P/N 93580 Speed Rotor Screen (dimpled). Discard the seven P/N 93497 Plugs; do not discard P/N 95872 Plugs. assembly (refer to Table II-4 of new P/N 96288 Speed Rotor replace with new P/N 96445
If assembly passes inspection, Screen is to be installed. If assembly fails inspection, Rotor and Screen Assembly.
C.
Inspect the muscles valve (refer to Table II-4 of Overhaul Manual). 1. 2. If valve passes inspection, Figure 2. If valve fails inspection, it may be reworked according to replace with new P/N 96027 Valve.
COMMERCIAL
ENGINE
BULLETIN
CECO POWER TURBINE GOVERNOR-REPLACE SEAL PLUGS AND SPEED ROTOR SCREEN OR ROTOR AND SCREEN ASSEMBLY AND REWORK OR REPLACE MUSCLES VALVE
OLD P/i
93497
95872
IDENTIFICATION FIGURE
PLUGS
L
REWORK
250
VALVE
COMMERCIAL
P
ENGINE
BULLETIN
CECO POWER TURBINE GOVERNOR-REPLACE SEAL PLUGS AND SPEED ROTOR SCREEN OR ROTOR AND SCREEN ASSEMBLY AND REWORK OR REPLACE MUSCLES VALVE PART II. A. Assemble, Test, and Reidentify Power Turbine Governor
Assemble the Power Turbine Governor according to the Overhaul Manual. 1. 2. Install new P/N 95872 Plugs. If new P/N 96268 Speed Rotor Screen is to be installed on the pin-shaft-rotor assembly, see Figure 3.
B. C.
Test the Power Turbine Governor according to the Overhaul Manual. Install P/N 93566 Throttle Lever at 80 on the quadrant. Ensure that the lever installed has reduced thickness at the serrations (refer to 250-C20 CEB-1002). Tighten nut to 65-85 ln. lbs. NOTE: NOTE: The serrated washer must be installed with the word outside facing out. This lever is not required for Bell JetRdnger installations. plate using New CECO P/N 104100 A2
f-
D.
Reidentify the power turbine governor identification l/8 in. number and letter punches as follows: Old DDA P/N 6876678 Old CECO P/N 104100 Al New DDA P/N 6876678A
E.
Record compliance with 250-C20 CEB-1004 in the White Pages, Part III, of the Engine Log book.
COMMERCIAL
ENGINE
BULLETIN
CECO POWER TURBINE GOVERNOR-REPLACE SEAL PLUGS AND SPEED ROTOR SCREEN OR ROTOR AND SCREEN ASSEMBLY AND REWORK OR REPLACE MUSCLES VALVE
ASSEMBLF NEW SCREEN WITH CHAMFER THIS S NO GAP BETWEEN SCR AND ROTOR PERMISSIBLE PIN-SHAFT-ROTOFi ASSY
&SCREEN
ASSEMBLY
COMMERCIAL
ENGINE
BULLETIN
CECO POWER TURBINE GOVERNOR-REPLACE SEAL PLUGS AND SPEED ROIQR SCREEN OR ROTOR AND SCRZEN ASSEMBLY AND REWORK OR REPLACE MUSCLES VALVE MATERIAL New P/N 6876678A (CECO 104100 A2) 96026 96027 96266 96267 96445 96268 95872 INFORMATION: Qty 1 Nomenclature Governor Assy, Power Turbine Diaphragm Assy, Muzcles Valve Valve, Muscles &tor Assy, Speed, Complete Rotor Assy, Speed Rotor & Screen Assy Screen, Speed Rotor PM Old P/N 6876678 (CECO 104100 Al) 93559 93561 94183 94181 --e-m 93580 93497 Diiposition A B C or G D E F F G
1 1 1 1 1 7
Stock Disposition: A B C D E F Rework and reidentify. P/N 93559 replaced with P/N 96026. Rework. P/N 94183 replaced with P/N 96266. P/N 94181 replaced with P/N 96267 If P/N 94185 Pin-P/N 94184 Shaft -P/N 94186 Rotor Assembly passes inspection, replace P/N 93580 Screen with P/N 96268. If assembly does not pass inspection, replace with P/N 96445 Rotor and Screen Assembly. Scrap L. 0. Davidson Service Manager Aircraft Engines