Beruflich Dokumente
Kultur Dokumente
COMMERCIAL
IndianaDolis.Indiana 46206
ENGINE
BULLETIN
December 23, 1977 BENDIX FUEL CONTROL, FUEL INLET FILTER ASSEMBLY-REPLACE PLANNING INFORMATION: EFFECTIVITY: All of the following Model 250 turboshaft fuel control assemblies Model Cl8 Cl8 c20 c20 C20B C20B REASON: DDA P/N. 6871119 6875343 6887766 6895661 6887755 6895663 Bendix P/N 2524463-3 2524527-2 2524552-4 2524552-6 less -5 2524644-l 2524644-3 less -2
Fine, grit-like dirt particles, swirling within the cylindrical filter screen, have eroded holes in the screen wires. Part No. 2539508 Fuel Filter Assembly has been released to reduce the high velocity, turbulent fuel flow within the filter screen. In the new filter assembly, three cross holes are added to the filter sleeve; also, the entrance hole diameter of the sleeve is increased. The entrance hole of the screen is enlarged, and the OD of its seal: is chamfered. Also, a load spring is added under the filter plug (or cap) to assure complete seating of the filter assembly.
DESCRIPTION:
COMMERCIAL
ENGINE
BULLETIN
BENDIX FUEL CONTROL, FUEL INLET FILTER ASSEMBLY-REPLACE INTERCHANGEABILITY: COMPLIANCE : Not affected It is recommended that the new filter assembly and spring be installed (1) at the next 100-hr aircraft inspection following parts availability from your distributor or (2) whenever a control is returned to an overhaul facility for any reason following parts availability. NOTE : Compliance with this buIIetin eliminates the lOOO-hr filter replacement requirement defined in 250-Cl8 (XL-80 or 250C20/C20B CSL-1045. Approved
APPROVAL : MANPOWER:
FAA-DER
It is estimated that 0.25 man-hour will be required to complete this bulletin at times other than overhaul. AVAILABILITY: Bendix P/N 2539508 2539437 557S6 2647428 186739* Nomenclature Filter Assy, Fuel Spring O-ring Plate, Identification Screw, Self-tapping Qty/Assy 1 1 1 1 2
MATERIAL
*Required at overhaul only TOOLING: WEIGHT AND BALANCE : REFERENCES: None Not affected ATW-2034 250-Cl8 CSL-80 250-C2O/C2OB CSL-1045 250-C20/C20B CEB-1079
COMMERCIAL
ENGINE
BULLETIN
BENDIX FUEL CONTROL, FUEL INLET FILTER ASSEMBLY-REPLACE ACCOMPLISHMENT I. INSTRUCTIONS: Assembly and P/N 2539511 (See Figure 1.)
Remove plug and filter assembly fuel control. Discard O-ring and filter assembly.
Lightly lubricate new P/N 557% O-ring with engine fuel and place it on plug. Install new P/N 2539508 Filter Assembly, P/N 2539437 Spring, and plug in fuel control. Tighten plug 65-70 lb in. and secure with lockwire.
II.
Reidentification A. In the field, reidentify fuel controls incorporating the new filter assembly with a large dot of blue dykem (or (equivalent) on the control body in a visible area. At overhaul, reidentify modified controls with a new P/N 2647428 Identification Plate filled out per Table I. (Data may be metal stamped, vibropeened, or scribed.) NOTE: -250-C20/C20B CEB-1079 must be incorporated before or concurrently with this bulletin before 250-C20/C20B controls can be reidentified with a new part number.
B.
III.
Record compliance with 250-Cl8 CEB-185 or C2O/C2OB CEB-1089 in the Engine Assembly (white pages) Modification Record, Part III of the Engine Log Book.
COMMERCIAL
BENDIX
ENGINE
BULLETIN
INLET FILTER
FUEL
INLET
FILTER
ASSEMBLY-REPLACE 1
FIGURE
COMMERCIAL
ENGINE
BULLETIN
COMMERCIAL
BENDIX
ENGINE
BULLETIN
INLET FILTER
MATERIAL New P/N 6894094 (2524463-4) 6894623 (2524527-3) 6894639 (2524552-5) 6895662 (2524552-6) 6894645 (2524644-2) 6895664 (2524644-3) 2539508 2539437 557S6 2647428 186739
INFORMATION: QtY 1 Control Nomenclature Assy, Fuel (Cl8) Old P/N 6871119 (2524463-4) 6875343 (2524527-2) 6887766 (2524552-4) 6895661 (2524552-6 less -5) 6887755 (2524644-l) 6895663 (2524644-3 less -2) 2523102 ----557S6 Identification Self-tapping 2647428 186739 1
Qt y 1
Disposition A
1 1
Control Control
Assy, Assy,
Fuel Fuel
(C18) (C20)
A B
Control
Amy,
Fuel
(C20)
Control
Assy,
Fuel
(C20B)
Control
Assy,
Fuel
(C20B)
1 1 1 1 2
Assy,
Fuel
C D C C C
COMMERCIAL
ENGINE
BULLETIN
BENDM FUEL CONTROL, FUEL INLET FILTER ASSEMBLY-REPLACE Stock Disposition A B C D Notes :
Rework and reidentify Rework and reidentify following incorporation CEB-1079 (bronze throttle bushing) Scrap removed part Added of 250-C20/C20B