Beruflich Dokumente
Kultur Dokumente
Model: HC003V/RF
N L
,,
1-10V
Antenna module
installation hole
Model: HC003V/RF
This is a combination of motion sensor and RF radio wave wireless transmission. The motion at 1 sensor (the master unit) can be passed onto other pre-defined individuals (the slave units) through R F transmission. Up to 15 units can be programed and grouped by means of Teach-and-Learn method. With KEELOQ coding technology, 1 master can triger max. 15 slaves , and 1 slaves can respond up to 15 masters respectively.
Mechanical structure
With both 1-10v output signal and 220-240v signal, it can switch on/off & dim any lighting applications. The motion signal from 1 sensor (the master sensor) can be transmitted to and trigger on other sensors (the slave unit) by RF transsmmion. This wireless radio wave transmission can reach 100 meters in open area.
Off
2
1 while the 1st sensor detects motion at 1st floor, the 1st sensor switch on 100%, the 2nd one to be standby brightness
Off
10%
10%
100%
100%
100%
2 The person walks to 2nd floor, the 2nd sensor at 100% and 3rd sensor to be standby brightness
46
10%
100%
4
3 The person walks to 3rd floor, the 3rd sensor at 100% and 4th to be standby brightnessat same time, 1st sensor dims to standby brightness after hold time
100%
100%
100%
10%
10%
Off
4 The person walks to 4th floor, the next sensor is 100%...... and at the same time, 1st sensor is off after standby period and 2nd sensor dims to standby brightness
HC003V/RF
HC003V/RF
Detection Pattern
wall mounting pattern(m)
ceiling mounting pattern(m)
5 4 3 2 1 0 1 2 3 4 5
5 4 1 2 3 4 5 6 7 8 9 10
2 3 4 5
2 1 0 1 2 3 4 5
47
Settings
1
Detection area
Detection area can be reduced by selecting the combination on the DIP switches to fit precisely for each specific application.
Hold-time
Hold-time means the time period you would like to keep the lamp on 100% after the person has left the detection area.
I 5S II 30S III 1 minute IV 5 minutes V 10 minutes VI 20 minutes I Disable II 1 hour III 30 min IV 10 min V 5 min VI 1 min I 5V (45~50%) II 4V (35~40%) III 3V (25~30%) IV 2V (15~20%) V 1.4V (5~10%)
This is the time period you would like to keep at the low light output level before it is completely switched off in the long absence of people.
This is the dimmed low light output level you would like to have after the hold-time in the absence of people.
The daylight threshold can be set on the potentiometer, from 2 lux up to 2000 lux, to fit for any particular application.
step1
slave unit
Press the SEND button on the master unit to send RF signal, the green LED on the master unit is then on to indicate the success of transmission. and the beeper turns to short indication: Upon receiving the transmission signal, the red LED on receiving unit will flash 2-3 times, which is the indication of successful teach-and-learn; and the beeper turns to short indiction:
slave unit master unit
step2
48
Wait for 180s period elapses, till the short beeper stops as well as the red LED on receiving unit goes off. The whole teach-and-learn process is completed. Or-Short press the Learn button again within the 180s period to finish the whole teach-and-learn process.
slave unit
step3
beeper is off Red LED goes off. 2nd short press this Learn button (Optional ) slave unit
If you want to RESET: A long press on Learn button (about 10s) resets and clears all previous commands it has receivedThe red LED keeps on flashing and then goes off in the end ; this is the indication of a successful reset and erase of all the previous groupings.
step4
(if necessary) ( slave unit )
Red LED keeps on flashing then goes off in 10s. Long press this Learn button
220-240v 800w Coding Detection area 5s/30s/1min/5min/10min/20min Standby period Daylight threshold RF. Communicatin Chanels 1min/5min/10min/30min/1hour / disable 2--2000 lux 15 channels for grouping <1mw Max. ( 30--150 O RF. Transmission distance 100 meters in open area Max. 5m. -20 RF Frequency ~ +60 433 MHz x H ): 8m x 5m Keeloq rolling code (tech/learn/reset/memory)
49