Beruflich Dokumente
Kultur Dokumente
1. Do not use the browser Back button or close or reload any exam windows during the exam.
2. Do not close Packet Tracer when you are done. It will close automatically.
Introduction
In this practice Packet Tracer Skills Exam, you will: finish the configuration of a partially configured network establish connectivity to the UK and the Internet through the use of static and dynamic routing
Addressing Table
Device Interface S0/0/0 S0/0/1 US-HQ S0/1/0 S0/1/1 Lo0 Fa0/0 US-R1 Fa0/1 S0/0/0 Lo0 Fa0/0 US-R2 Fa0/1 S0/0/0 Lo0 Fa0/0 ServerLAN US-Admin US-PC2 US-PC3 Fa0/1 Lo0 NIC NIC NIC Address 192.168.20.245\30 192.168.20.241\30 64.100.50.2\30 128.107.25.1\30 172.16.0.4\32 192.168.20.1 192.168.20.118 192.168.20.246 172.16.0.1 192.168.20.65 192.168.20.113 192.168.20.242 172.16.0.2 192.168.20.97 192.168.20.114 172.16.0.3 192.168.20.66 192.168.20.94 192.168.20.62 192.168.20.98 Subnet Mask 255.255.255.252 255.255.255.252 255.255.255.252 255.255.255.252 255.255.255.255 255.255.255.192 255.255.255.248 255.255.255.252 255.255.255.255 255.255.255.224 255.255.255.248 255.255.255.252 255.255.255.255 255.255.255.240 255.255.255.248 255.255.255.255 255.255.255.224 255.255.255.224 255.255.255.192 255.255.255.240 n/a n/a n/a n/a n/a n/a n/a n/a n/a 192.168.20.65 192.168.20.65 192.168.20.1 192.168.20.97 n/a Default Gateway
www.xyzcorp.com NIC
Note: The password for user EXEC mode is cisco. The password for privileged EXEC mode is class.
Configure and activate all interfaces for US-R2 that are listed in the addressing table. Configure US-PC2 with the last IP address in the subnet. Configure the Fa0/1 interface on US-R1 with the last IP address in the subnet.
c. Verify connectivity.
UK Subnets 10.10.0.0/24 10.10.1.0/24 10.10.2.0/25 10.10.2.128/25 10.10.3.0/25 10.10.3.128/26 10.10.3.192/27 10.10.3.224/28 10.10.3.240/30 10.10.3.244/30 10.10.3.248/30 10.10.3.252/30
Configure a default route on US-HQ to send to the Internet all other traffic for destinations that are not found in the US-HQ routing table. Use theoutbound interface argument.
Configure US-HQ to send the default route to US-R1 and US-R2 in OSPF updates. Configure US-R1 to always be the DR by using a priority of 150. Configure US-R2 to always be the BDR by using a priority of 75. Change the hello interval to 30 seconds on US-R1 and US-R2 for the LAN that these two routers share with ServerLAN. Verify OSPF neighbor status. Verify that the routing tables on US-R1, US-R2, and US-HQ contain all the expected routes. It may be necessary to shutdown and then reactivate interfaces to force OSPF to converge.
Version 1.0 Created in Packet Tracer 5.3.2.0027 and Marvel 1.0.1 All contents are Copyright 1992 - 2011 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.