Beruflich Dokumente
Kultur Dokumente
Size Range: 18" (25200mm) Temperature Range: -1501200F (-101649C) ANSI Class Rating: 150600 Body Materials: Carbon steel, 316 stainless steel Valve Style: Double-seated, balanced, or single-seated top & bottom guided globe control valve Trim Characteristics: Equal percentage contour, linear contour Actuator Type: Direct or reverse acting spring & diaphragm, springless diaphragm, electric motor or manual handwheel
Angle Valves
Major Markets: Petroleum, refining, power, chemical, steel Design Features: Angle design valves feature a streamlined interior flow passage to prevent accumulation of media on the body wall. Angle valves are ideal for applications handling slurries, viscous and flashing/cavitating media with high-pressure drops. Size Range: 18" (25200mm) Temperature Range: -1501200F (-101649C) Body Materials: 316 stainless steel, carbon steel ANSI Class Rating: Class 150600, high pressure to 6000 psig (41340 kPa) Valve Style: Top guided angle valve Trim Characteristics: Equal percentage or linear contoured Actuator Type: Direct or reverse acting spring & diaphragm, electric motor or manual handwheel
Body Materials: Cast iron, bronze ANSI Class Rating: 125 Valve Style: Double-seated or single-seated skirt guided globe control valve Trim Characteristics: Modified linear v-port, equal percentage v-port Actuator Type: Direct or reverse acting spring & diaphragm, electric motor or manual handwheel
Butterfly Valves
Body Materials: Carbon steel, 316 or 317 stainless steel Valve Style: High performance butterfly valve, wafer or lugged Actuator Type: Lever, handwheel, chainwheel, square nut, PowerRac double-acting and spring-return, spring & diaphragm, Compak double-acting and springreturn Body Materials: Cast iron, ductile iron Valve Style: Resilient seated butterfly, wafer or lugged Actuator Type: Lever, handwheel, chainwheel, square nut, PowerRac double-acting and spring-return cylinder, electric motor, Compak double-acting and spring-return cylinder, spring & diaphragm
Butterfly Valves
Size Range: 3120" (803000mm) Temperature Range: to 290F (143C) AWWA Class: 25A, 75B, 150B, 250B Pressure Rating: 2575 psi (170520 kPa) , 150250 psi (10301700 kPa) CWP Shutoff Bubble tight to full rated pressure. Body Materials: Cast iron, ductile iron Valve Style: Flanged and mechanical joint Actuator Type: Lever, handwheel, chainwheel, square nut, cylinder, electric motor Special Construction: Square and Rectangular AWWA Butterfly Valves are designed in a variety of sizes for square/rectangular configurations. Specially designed packages for pump check control applications are also available.
Ball Valves
Plug Valves
Eccentric Plug Valves (PEC)
Major Markets: Wastewater, water, air conditioning, mining, chemical, power, steel Design Features: Eccentric action and resilient plug facings assure lasting dead-tight shutoff. Clean interior design and straightthrough flow allow high maximum flow capacity with minimum pressure drop. Heavy-duty stainless steel bearings, choice of resilient plug facings, welded-in corrosion resistant nickel seat and variety of end styles are available. Capable of handling clean and dirty liquids and gases, sludges and slurries. Size Range: .572" (151800mm) Temperature Range: to 300F (150C) Pressure Rating: 125450 psi (8603100 kPa) CWP shutoff pressure to 275 psi (1980 kPa) Shutoff Class: Resilient plug facing: drip tight rating up to 275 psi (1890 kPa) Body Materials: Cast iron, ni-resist, aluminum, carbon steel, stainless steel, Alloy 20, Monel and ductile iron
Plug Valves
Permaseal Tapered Plug Valves (PPS)
Major Markets: Chemical, power, mining, paper, petroleum Design Features: Permaseal Plug Valves feature a non-lubricated tapered plug and two individual seats to provide a double seal and bi-directional shutoff. The self-adjusting plug, self-aligning double seat, dynamic stem seal, and top-entry design allow for easy maintenance. Numerous special construction options are available to meet a variety of applications. Size Range: .56" (15150mm) Temperature Range: to 1000F (540C) ANSI Class Rating: 150, 300 Pressure Rating: 275740 psi CWP (18905100 kPa) ANSI B16.104 Shutoff Class: Carbon graphite seat, Class IV; resilient seat, Class VI Body Materials: Carbon steel, 316L stainless steel, Alloy 20, ductile iron, Monel, Hastelloy C Valve Style: Tapered plug; 2-way, 3-way, jacketed, double block and bleed, flush through Actuator Type: Lever, handwheel, Compak double-acting or spring-return, electric motor
10
Valve Style: Level sensor knife gate valve, lugged Actuator Type: Rachet handle or square drive with non-rising stem
Pressure Rating: 150 psi (1030 kPa) CWP Valve Style: Ported gate valve, wafer Body Materials: Ductile iron, 316 stainless steel Actuator Type: Handwheel, chainwheel, pneumatic and hydraulic cylinder, electric motor
12
Consistency Transmitters
Rotating Consistency Transmitters (SDP)
Major Markets: Paper Design Features: Consistency range from 0.75% to 10% at velocities from 0.1 to 10 feet (.03 to 3 meters) per second. Motordriven sensor located in pulp stock flow is highly sensitive to consistency changes and insensitive to flow changes. Capable of measuring consistency changes as small as .0025%. Chamber Size: 1236" (300900mm) Chamber Pressure Rating: 125 psi (860 kPa) Chamber Material: 304, 316 or 317L stainless steel
Shaft, Sensor Material: 316 or 317L stainless steel Chamber Style: Horizontal, vertical, open, pan Output: Pneumatic, electronic
13
Actuators
PowerRac Actuators
The rack and pinion design of PowerRac Actuators provides high-operating torque for accurate control in modulating services, and high opening torque for on/off services. The unique square collet coupling rigidly clamps the drive pinion to the valve shaft, eliminating backlash in the drive connection. This rigid connection allows thrust from the cylinder to precisely position the valve. Positioners are solidly mounted on the actuator housing with a square nut, feeding exact valve position directly to the positioner. No lost motion assures accurate valve positioning. The modular design and compact size allow the actuator to be close coupled to the valve. Standard ISO bolt circle allows PowerRac Actuators to be used on all DeZURIK quarter turn valves. Double-acting or fail-safe springreturn cylinder options available. Lifetime Warranty: DeZURIK has always been committed to the highest quality products and service, and our Lifetime Warranty on PowerRac demonstrates our confidence in the quality and features of this actuator. Contact your local DeZURIK representative for details.
Compak Actuators
Compak Actuators are a versatile rack-and-pinion design actuator available as either doubleacting or fail-safe spring-return. Upper and lower bushings, combined with a large wear pad, minimize wear and increase actuator life cycle. The compact, modular design allows the actuator to be mounted for a low profile assembly. Compak Actuators are matched to each valves torque requirements to ensure that the most economical valve and actuator package is specified.
14
Actuators
Accessories
M-Series Actuators
M-Series Actuators are designed for use on smaller DeZURIK AWWA Butterfly Valves. The M-Series Actuator meets the requirements of AWWA C504 standards. The fully enclosed scotch yoke mechanism allows the M-Series Actuator to provide a torque curve that matches the torque requirements of the valve. The thread system of the traveling nut is self-locking, maintaining disc position under varying flow conditions.
LA-Series Actuators
LA-Series Actuators are designed for use on large DeZURIK AWWA Butterfly Valves. The LA-Series Actuator meets the requirements of AWWA C504 standards. The link-arm mechanism allows the LA-Series Actuator to provide characterized closure that slows valve travel and increases torque as the disc comes into the seat. The actuators feature high compressive strength yoke nut bearings that ensure reliable operation and increased cycle life. The actuator is self-locking, maintaining valve position under varying flow conditions.
15
1 = Typical Application
2 = May Be Used
3 = Limited Application
4 = Not Used
Linear Control Valves Application Requirements Function: On-Off Throttling Diversion Media: Liquids (Clean) Liquids (Dirty) Liquids (Viscous) Liquids (Corrosive) Slurries (Sludge) Liquids & Slurries (Scaling) Slurries (Abrasive) Slurries (Fibrous) High Pressure Steam (+150lbs.) Low Pressure Steam Gasses (Clean) Gasses (Dirty) Gasses (Corrosive) Dry Materials Valve Characteristics: High Flow Capacity Low Head Loss (Wide Open) Low Torque/Thrust High Temp., 800F+ (425C+) Cryogenic Erosion Resistance Cavitation (Kc) @ 60% Open Recovery Factor FL2 @ 60% Open Shutoff Class Top & Cage Top Bottom Guided Guided Guided Skirt Guided Angle 3-Way
Rotary Control & Isolation Full Port High V-Port Metal PerformControl Seated ance Valve Ball Valve Butterfly 2 1 4 1 1 1 1 1 3 3 1 3 1 1 1 1 4 1 1 1 4 4 3 .49 .61 1 2 3 1 1 1 1 3 1 3 1 1 2 1 1 1 4 1 1 4 3 3 2 .22 .66 1 1 3 1 3 2 1 3 4 2 2 1 1 1 3 1 4 1 1 1 3 3 2 .35 .43
Pressure Rating
ANSI ANSI ANSI ANSI 125-900/ 125-900/ 125-900- 1501500 1500 1500 600
ANSI II, ANSI IV, ANSI IV, VI, or V,VI or V or IV better better ANSI ANSI ANSI 150 & 150 & 150 & 300 300 300
Note: This valve selection chart is designed to provide you with a quick reference on valve style capabilities. The chart considers both cost and performance factors for a specific application when determining whether a valve style is rated Typical, May Be Used, or Limited Application. For more information, contact DeZURIK or your local representative with your specific application requirements.
16
1 = Typical Application
2 = May Be Used
3 = Limited Application
4 = Not Used
Application Requirements Function: On-Off Throttling Diversion Media: Liquids (Clean) Liquids (Dirty) Liquids (Viscous) Liquids (Corrosive) Slurries (Sludge) Liquids & Slurries (Scaling) Slurries (Abrasive) Slurries (Fibrous) High Pressure Steam (+150lbs.) Low Pressure Steam Gasses (Clean) Gasses (Dirty) Gasses (Corrosive) Dry Materials Valve Characteristics: High Flow Capacity Low Head Loss (Wide Open) Low Torque/Thrust High Temp., 800F+ (425C+) Cryogenic Erosion Resistance Cavitation (Kc) @ 60% Open Recovery Factor FL2 @ 60% Open Shutoff Class
Plug Gate Valves Valves 3-Way Perma- Knife Resilient Ported AWWA Eccentric & seal Seated Gate Gate 4-Way (Tapered) 1 1 3 1 2 1 2 2 4 3 2 4 4 1 2 2 2 1 1 2 4 4 3 .35 .40 1 1 3 1 2 2 4 2 4 4 4 4 4 1 2 4 4 1 1 2 4 4 4 .35 .40 1 1 4 1 1 1 1 1 3 2 2 4 3 1 1 1 2 1 1 2 3 4 1 .59 .70 4 1 1 1 1 1 1 1 4 2 1 4 3 1 1 1 4 1 1 1 4 4 3 N/A N/A 1 3 1 1 2 1 1 2 4 3 3 4 2 1 2 1 4 1 1 1 2 4 3 N/A N/A 1 3 4 1 1 1 2 1 4 1 1 4 4 2 2 2 1 1 1 2 1 4 1 N/A N/A 1 4 4 3 1 1 1 1 1 1 1 4 3 2 2 2 1 1 1 2 4 4 1 N/A N/A
Pressure Rating
ANSI IV, VI or N/A better 150/ AWWA 125125 psi 175 psi 25, 75, 450 psi CWP CWP 150 CWP
ANSI IV, Class VI VI or TAPPI or better better ANSI 125/ 100/ 150 & 150 psi 150 psi 300 CWP CWP
Note: This valve selection chart is designed to provide you with a quick reference on valve style capabilities. The chart considers both cost and performance factors for a specific application when determining whether a valve style is rated Typical, May Be Used, or Limited Application. For more information, contact DeZURIK or your local representative with your specific application requirements.
17
Products
Maxum Rotary Control Valves Sizes 112" (25300mm) for highly erosive services. Features high throttling accuracy and four flow capacity ranges. Eccentric Plug Valves Sizes 0.572" (151800mm) in a wide choice of materials and resilient plug facings. HP Butterfly Valves Sizes 248" (501200mm) for applications to 740 psi (5100 kPa), plus Intelli-Seal extra-tight metal, fire tested and PTFE seated models. V-Port Ball Valves Sizes 120" (25500mm), pressures to 740 psi (5100 kPa) and temperature ratings to 1000F (537C). Flanged and flangeless designs. Resilient Seated Butterfly Valves Sizes 236" (50900mm) in two styles with 175 and 225 psi (1210 and 1550 kPa) pressure ratings and wafer and lugged body styles. AWWA Butterfly Valves Sizes 3120" (803000mm). Meets AWWA C504 standards. 3- and 4-Way Plug Valves Sizes 316" (80400mm) for shut-off and switching applications, plus a variety of body materials. Metal Seated Full Port Ball Valves Sizes 212" (50300mm) are designed for trouble-free operation in digester blow-down applications and for handling corrosive liquids, gases and abrasive slurries. Precision Electric Control Valves Unmatched control accuracy provides up to 16,000 discrete repeatable throttling positions in 90 plug rotation. Accepts analog or digital signals. Sizes 420" (100500mm). Permaseal Plug Valves Sizes 0.56" (15150mm) in ANSI Class 150 and 300 ratings. Body styles include 2-way, 3-way, jacketed, double block and bleed and flush through for corrosive and high temperature applications. Knife Gate Valves Rugged designs for corrosive and abrasive service on liquids, slurries and dry materials. Pressures to 150 psi (1030 kPa) and sizes 272" (501800mm). Consistency Transmitters Rotating sensor, AccuTrax blade sensor, open type and pan type chambers for pulp and paper consistency control applications. Unival Ported Gate Valves Sizes 248" (501200mm) for scaling, corrosive and abrasive services. Reinforced elastomer sleeve forms bubble-tight seal flush with the wall of the pipe. Regulators and Pump Governors FW-1, BI and D-O Flomatic regulators for direct control of boiler feedwater level. Sizes 13" (2580mm). SDS-2 steam governor for use in automatic steam pressure control up to 200 psig (1380 kPa). Sizes 1.54" (40100mm), pressure class ANSI 250600. General Service and Severe Duty Linear Control Valves Sizes 0.524" (15600mm) with pressure class ratings from ANSI 1254500. Top Guided, Cage Guided, Balanced, Unbalanced and Tandem construction with quick-change trim. Wide variety of body styles to meet the exact application requirements. Low noise, tight shut-off, low flow and anticavitation trim options to meet the most demanding requirements. Available in straight, angle, fabricated and 3-way globe body styles. Manual, pneumatic, hydraulic or electric actuation. Steam and Gas Desuperheaters For line sizes from 136" (25900mm) and larger. Pressure classes ANSI 1504500. Wide range of products including Mechanical Atomizing, Spring Assisted Multiple Nozzle, Variable Annulus, Steam Atomizing, Variable Orifice and Multiple Nozzle with Integral Control Valve designs. Temperatures to 1200F (650C). Steam Conditioning Equipment Preconfigured Pressure Reducing and Desuperheating Stations (PRDS) are cast products in sizes 1x2", 2x4", 3x6", 4x8" and 6x12" (25x50, 50x100, 80x150, 100x200 and 150x300mm) angle style bodies with pressure class ratings from ANSI 6002500. Fabricated Direct Steam Conditioning Valves (DSCV) are fabricated in pressure classes ANSI 1504500 for sizes 836" (200900mm) angle construction. Widely used in process steam and turbine bypass applications. Manual, pneumatic, hydraulic or electric actuation. Actuators Pneumatic Spring and Diaphragm and Piston Actuators for linear control valves. Rotary spring diaphragm, PowerRac rack and pinion style, G-Series and Compak spring return and double acting actuators. A wide variety of manual and electric motor actuator options. Control Accessories Smart, Digital, Electro-Pneumatic and Pneumatic positioners. Other devices including limit switches, position transmitters, transducers, filter regulators, solenoid valves, fail in place devices, booster relays, quick release valves and other accessories available to customize equipment to meet system requirements.
E-Mail: info@dezurikcopesvulcan.com
DeZURIK/COPES-VULCAN - NORTH CHINA Room 103, Haowei Building Number 25, Beitaipingzhuang Road Haidian District, Beijing 100088 Peoples Republic China Telephone: 86-10-62381018 Fax: 86-10-62381017 DeZURIK/COPES-VULCAN - SINGAPORE 31 Kaki Bukit Road 3 #02-04, Techlink Singapore 417818 Telephone: 65-547-2390 Fax: 65-842-7578 DeZURIK/COPES-VULCAN - INDIA 220, Midas, Sahar Plaza Sir M. V. Road, Andheri (E) Mumbai - 400059 Telephone: 91-22-838-5857 Fax: 91-22-838-5895
DeZURIK/COPES-VULCAN - MEXICO Nueva Jersey 4331 Fracc. Industrial Lincoln Monterrey NL CP64310 Mexico Telephone: 52-83-707164/5026 Fax: 52-83-713004 DeZURIK/COPES-VULCAN - UNITED KINGDOM Road Two, Industrial Estate Winsford, Cheshire CW7 3QL United Kingdom Telephone: +44 1606 552041 Fax: +44 1606 552700 DeZURIK/COPES-VULCAN - SOUTH CHINA General Signal China Limited 1/F, No. 18, 485 Guiping Road Caohejing Hi-Tech Park Shanghai 200233 China Telephone: 86-21-64853018 Fax: 86-21-64852438
DeZURIK/CopesVulcan reserves the right to incorporate our latest design and material changes without notice or obligation. Design features, materials of construction and dimensional data, as described in this bulletin, are provided for your information only and should not be relied upon unless confirmed in writing by DeZURIK/CopesVulcan. Certified drawings are available upon request.
Printed in the U.S.A. 011701