Beruflich Dokumente
Kultur Dokumente
com
Legal Notices
Raisecom Technology Co., Ltd makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Raisecom Technology Co., Ltd shall not be held liable for errors contained herein or direct, indirect, special, incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Warranty.
A copy of the specific warranty terms applicable to your Raisecom product and replacement parts can be obtained from Service Office.
Copyright Notices.
Copyright 2007 Raisecom. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in Writing from Raisecom Technology Co., Ltd.
Trademark Notices
is the trademark of Raisecom Technology Co., Ltd. Java is a U.S. trademark of Sun Microsystems, Inc. Microsoft is a U.S. registered trademark of Microsoft Corporation. Windows NT is a U.S. registered trademark of Microsoft Corporation. Windows 2000 is a U.S. registered trademark of Microsoft Corporation. Windows XP is a U.S. registered trademark of Microsoft Corporation. Windows and MS Windows are U.S. registered trademarks of Microsoft Corporation.
Contact Information
Technical Assistance Center
The Raisecom TAC is available to all customers who need technical assistance with a Raisecom product, technology, or, solution. You can communicate with us through the following methods:
2nd Floor, South Building of Rainbow Plaza, No.11 Shangdi Information Road, Haidian District, Beijing 100085 +86-10-82883305 +86-10-82883056
Feedback
Comments and questions about how the OPCOM3105 system software works are welcomed. Please review the FAQ in the related manual, and if your question is not covered, send email by using the following web page: http://www.raisecom.com/en/xcontactus/contactus.htm. If you have comments on the OPCOM3105 specification, instead of the web page above, please send comments to: export@raisecom.com
CONTENTS
Release Notes------------------------------------------------------------------------------------------------- 5 Chapter 1 System Overview -------------------------------------------------------------------------- 1 Chapter 2 How to Use The Command Line ------------------------------------------------------ 2
2.1 Software and hardware environment ---------------------------------------------------------------------------------2 2.2 Getting helps ------------------------------------------------------------------------------------------------------------------2 2.3 How to use history command -------------------------------------------------------------------------------------------3 2.4 How to use edit performance --------------------------------------------------------------------------------------------3 2.5 Command line mode--------------------------------------------------------------------------------------------------------3
Chapter 3
3.1 Basic system commands and configuration -----------------------------------------------------------------------4 3.2 Management of configuring file and startup file ------------------------------------------------------------------4
3.2.1 Configure startup file ---------------------------------------------------------------------------------------------------------------------- 4 3.2.2 Host file --------------------------------------------------------------------------------------------------------------------------------------- 4 3.2.3 Update host software from bootrom --------------------------------------------------------------------------------------------------- 4 3.2.4 Update host software in Privileged EXEC mode ----------------------------------------------------------------------------------- 8
Chapter 4
4.1 Mappings from IP address to physical address----------------------------------------------------------------- 10 4.2 Configure IP address of SNMP interface -------------------------------------------------------------------------- 11 4.3 Configure a static routing----------------------------------------------------------------------------------------------- 11 4.4 Configure SNMP COMMUNITY table -------------------------------------------------------------------------------- 12 4.5 Configure SNMP trap-server host ------------------------------------------------------------------------------------ 13
7.1 Interface rate-limit --------------------------------------------------------------------------------------------------------- 17 7.2 Storm-control configuration ------------------------------------------------------------------------------------------- 17 7.3 MAC information configuration --------------------------------------------------------------------------------------- 18 7.4 QOS function configuration -------------------------------------------------------------------------------------------- 19
Chapter 8 Chapter 9
9.1 Overview ---------------------------------------------------------------------------------------------------------------------- 23 9.2 Point-to-point topology -------------------------------------------------------------------------------------------------- 23 9.3 Chain topology ------------------------------------------------------------------------------------------------------------- 23 9.4 Ring topology --------------------------------------------------------------------------------------------------------------- 24
9.4.1 2F SNC-P ---------------------------------------------------------------------------------------------------------------------------------- 24
Release Notes
Revisions First release Add Point-to-Point network management path application at end section 10.1.
20080912
200711
Preface
Relevant Manuals
OPCOM3105 Commands Notebook This is the Configuration Guide of OPCOM3105 and OPCOM3107.
Organization
Chapter 1 System Overview Introducing function features of OPCOM3105 device systematically. Chapter 2 How to Use the Command Line This chapter introduces the using features and basic methods of configuring OPCOM 3105 device by command line. Chapter 3 System Commands Configuration This chapter introduces the function and configuration of system commands of OPCOM 3105 device. Chapter 4 Network Protocol Configuration This chapter introduces the function and configuration of network protocol of OPCOM 3105 device. Chapter 5 Timeslot Assignment This chapter introduces the configuration of timeslot assignment of OPCOM 3105 device. Chapter 6 Protection Configuration This chapter introduces the protection function and configuration of OPCOM 3105 device. Chapter 7 Eth-switch Function Configuration This chapter introduces the Ethernet-switch function and configuration of OPCOM 3105 device.
Chapter 8 VLAN Configuration Introducing the configuration of VLAN of OPCOM3105 device. Chapter 9 Network Topology This chapter introduces the network topology of OPCOM 3105 device. Chapter 10 Typical Application This chapter introduces typical application of OPCOM 3105 device.
Compliance
The RC series products developed by Raisecom are strictly complied with the following standards as well as ITU-T, IEEE, IETF and related standards from other international telecommunication standard organizations: YD/T900-1997 SDH Equipment Technical Requirements - Clock YD/T973-1998 SDH 155Mb/s and 622Mb/s Technical conditions of optical transmitter module and receiver module YD/T1017-1999 Network node interface for the Synchronous Digital Hierarchy (SDH) YD/T1022-1999 Requirement of synchronous digital hierarchy (SDH) equipment function YD/T1078-2000 SDH Transmission Network Technique Requirements-Interworking of Network Protection Architectures YD/T1111.1-2001 Technical Requirements of SDH Optical Transmitter/Optical Receiver Modules2.488320 Gb/s Optical Receiver Modules YD/T1111.2- 2001 Technical Requirements of SHD Optical Transmitter/Optical Receiver Modules2.488320 Gb/s Optical Transmitter Modules YD/T1179- 2002 Technical Specification of Ethernet over SDH G.703 Physical/electrical characteristics of hierarchical digital interfaces G.704 Synchronous frame structures used at 1544, 6312, 2048, 8448 and 44 736 kbit/s hierarchical levels G.707 Network node interface for the synchronous digital hierarchy (SDH) G.774 Synchronous digital hierarchy (SDH) - Management information model for the network element view G.781 Synchronization layer functions G.783 Characteristics of synchronous digital hierarchy (SDH) equipment functional blocks G.784 Synchronous digital hierarchy (SDH) management G.803 Architecture of transport networks based on the synchronous digital hierarchy (SDH) G.813 Timing characteristics of SDH equipment slave clocks (SEC) G.823 The control of jitter and wander within digital networks which are based on the 2048 kbit/s hierarchy G.825 The control of jitter and wander within digital networks which are based on the synchronous
digital hierarchy (SDH) G.826 End-to-end error performance parameters and objectives for international, constant bit-rate digital paths and connections G.828 Error performance parameters and objectives for international, constant bit-rate synchronous digital paths G.829 Error performance events for SDH multiplex and regenerator sections G.831 Management capabilities of transport networks based on the synchronous digital hierarchy (SDH) G.841 Types and characteristics of SDH network protection architectures G.842 Interworking of SDH network protection architectures G.957 Optical interfaces for equipments and systems relating to the synchronous digital hierarchy G.691 Optical interfaces for single channel STM-64 and other SDH systems with optical amplifiers G.664 Optical safety procedures and requirements for optical transport systems I.731 ATM Types and general characteristics of ATM equipment I.732 ATM Functional characteristics of ATM equipment IEEE 802.1Q Virtual Local Area Networks (LANs) IEEE 802.1p Traffic Class Expediting and Dynamic Multicast Filtering IEEE 802.3 CSMA/CD Access Method and Physical Layer Instruction
www.raisecom.com
User Manual
OPCOM3105 is a compact SDH Multi Service Access Device that implement SDH 155M upstream at line side. It can be used as remote device of OPCOM3500E to connect with OPCOM3500E SDH tributary unit. The service side provides 3 paths 10/100M Ethernet with switching function and one independent Ethernet interface by EOS to fulfill accessing of Ethernet service and access 4 paths E1 to SDH. Expanding slot of the device can connect with E-SUBM series sub-module of Raisecom to provide users flexible solutions for service accessing. 1+1 path protection and multiplex section protection functions are available in this device. The network maintenance and management is realized by DCC in-band network management path of STM-1. OPCOM3107 just makes some modification based on OPCOM3105. the modification including: add redundant power supply, change the E1 interfaces from 4 to 8 or 16, and delete expanding slot on OPCOM3105. in fact there are 8E1 or 16E1 and 4 Fast-Ethernet, 2 STM-1 optical interface and 2 DC/AC power supply on OPCOM3107. Thus the operations about E-SUBM series expanding cards mentioned in this manual are not available to OPCOM3107 devices.
www.raisecom.com
User Manual
This chapter is consisted of: Software and hardware environment Getting helps How to use history command How to use edit properties Command line mode
This chapter mainly introduces uses of command line. When configuring OPCOM3105 system, device SNMP address, community, DCC network management path need to be configured, other service configurations are recommended to accomplish by EMS (Element Management System).
abbreviated-command-entry<Tab>
command ?
www.raisecom.com
User Manual
OPCOM3105#
OPCOM3105(config)#
OPCOM3105(config-remote/PATH)# PATH: path of remote device OPCOM3105 (config-TYPE/PATH)# TYPE: interface type, like eth, stm, e1, etc. PATH: interface index.
www.raisecom.com
User Manual
This chapter is consisted of: Basic system commands and configuration Management of configuring file and startup file User management
www.raisecom.com by Xmodem protocol, the other one is to update from network by FTP protocol. Upgrade the program file through Xmodem protocol serial interface: 1) Users who has administrator right logs in Privileged EXEC mode by serial port; 2) Input command reboot; 3) Press <Space> key to enter [raisecom] interface, show below information: ? h i s d u m r test show this list show this list modify network manage port ip address show network manage interface information delete core file update your system update microcode reboot system test the hardware
User Manual
----------------------------------1. | serial -
----------------------------------2. | network -
----------------------------------2. | 14400 -
----------------------------------3. | 19200 -
----------------------------------4. | 38400 -
6) After inputting the chosen baud rate, the system is waiting to transmit upgrade file through the serial interface, now click [Transfer] as below figure shows:
www.raisecom.com
User Manual
Figure 1
Figure 2
Click <Browse> to choose the program file to be downloaded, click <Send> then shows the below interface:
www.raisecom.com
User Manual
Upgrade the program file through network via FTP protocol: 1) The user with administrator privilege can login and enter the privileged EXEC mode through the serial port; 2) Enter the command reboot; 3) Click <Space> key to enter the [raisecom] interface, input ? to show commands list. ? h i s d u m r test show this list show this list modify network manage port ip address show network management interface information delete core file update your system update microcode reboot system test the hardware
----------------------------------1. | serial 7
www.raisecom.com
----------------------------------2. | network -
User Manual
-----------------------------------
192.168.2.225
OPCOM3105..z
passwd:
Input host IP address, file name, user name and password of FTP in turn, and then get into the interface as follows:
Start to connect host, please wait...
Input host IP address, file name, user name and password of FTP in turn, and then get into the interface as follows:
Are you sure[Y/N]: y
Input y to confirm the operation is correct, then shows the below interface:
Loading, please wait...file length = 1884532 Please select the disk for saving image 1. core: 8
www.raisecom.com
2. exit Please input the number: 1
User Manual
no-encryption|md5PASSWORD
www.raisecom.com
User Manual
This chapter is consisted of: Mapping from IP address to physical address Configure IP address of SNMP Configure a static routing Configure SNMP community table Configure SNMP trap-server host
LNote:
Use global configuration command arp delete A.B.C.D to delete a mapping from IP
Example: Add a mapping from IP 192.168.2.11 to physical address 00:50:8d:46:fb:3: OPCOM3105# config
Configuration mode, one command input per times. End with CTRL-Z.
--------------------------------------------------------------------------
10
www.raisecom.com
192.168.2.11 00:50:8d:46:fb:3 c05 0 0 hw0
User Manual
--------------------------------------------------------------------------
Configure network management IP address. A.B.C.D : IP address of network management, decimal number; ip address A.B.C.D [.B.C.D] [.B.C.D] : sub-net mask of network management IP address, decimal number. Table 4-2 SNMP Network Management IP Commands Table Example: Configure IP of network management to be 192.168.2.20 and sub-net mask to be 255.255.255.0 OPCOM3105# config
Configuration mode, one command input per times. End with CTRL-Z.
OPCOM3105(config)#interface snmp OPCOM3105(config-snmp)#ip address 192.168.2.20 255.255.255.0 OPCOM3105(config-snmp)# show interface snmp
Interface:snmp Operation Status :up
Table 4-3 Static Routing Configuration Table Use global configuration command no ip route A. B. C. D. A. B. C. D to delete a route. The first group of A.B.C.D is destination IP, the second group of A.B.C.D is destination IP mask.
User Manual
-------------------------------------------------------------------------2.2.2.0/24 3.3.3.0/24 192.168.2.0/24 192.168.4.0/24 192.168.4.0/24 2.2.2.2 3.3.3.3 192.168.4.250 192.168.4.100 192.168.4.100 2010003 2010003 2010003 2000101 10101 0 0 0 2 0 0 0 0 0 0 8 8 1 2 8 ppp1 ppp2 sng0 sng0 sng0
--------------------------------------------------------------------------
-------------------------------------------------------------------------2.2.2.2 2.2.2.2 3.3.3.3 3.3.3.3 127.0.0.1 192.168.4.100 192.168.4.100 192.168.4.100 192.168.4.100 192.168.4.100 127.0.0.1 127.0.0.1 2000005 5 2000005 5 2200005 2000005 1 0 1 0 0 0 1 0 1 0 0 0 2 8 2 8 2 8 ppp1 ppp1 ppp2 ppp2 lo0 lo0
--------------------------------------------------------------------------
Add a community. COMMUNITYNAME : community name snmp-server community COMMUNITYNAME [RO | RW] RO: read only; RW: ready and write. exit Exit global configuration and enter Privileged EXEC mode. Show COMMUNITY table. show snmp-server community Table 4-4 Configure SNMP Community Use global configuration command no snmp-server community COMMUNITYNAME to delete a community.
12
www.raisecom.com Example: Add a community named raisecom with right of read and write. OPCOM3105# config
Configuration mode, one command input per time. End with CTRL
User Manual
Table 4-5 Configure SNMP Trap-server Use the global configuration command no snmp trap-server A.B.C.D to delete a trap-server. Example: Add a trap-server with IP of 192.168.1.16 OPCOM3105# config
Configuration mode, one command input per time. End with CTRL
13
www.raisecom.com
User Manual
This chapter introduces the configuration of timeslot assignment. Commands Config Description Enter global configuration mode. Assign backboard timeslot for the port. sdh <1-2>: choose SDH port from which the signal send out. (vc12/vc3): timeslot assignment level, in support of vc12 and vc3 at present. TSSTRING: assigned timeslot number. TSSTRING: timeslot number. Assign backboard timeslot for port. sdh <1-2>: choose SDH port from which the signal send out. (vc12/vc3): timeslot assignment level, in support of vc12 and vc3 at present. SVCTSSTRING: assigned timeslot number; TSSTRING: timeslot number. SDHTSSTRING: assigned timeslot number; TSSTRING: timeslot number. Show timeslot assigning information.
show timeslot
OPCOM3105 has two EOS interfaces; each EOS interface can assign VC12 or VC3 type timeslot. One interface can be assigned for one type of timeslot only, deletes all different timeslot types before changing assigned timeslot type. E1 interface timeslot assignment
OPCOM3105 has 10 E1 interfaces; 1-4 E1 interfaces are on panel, 5-8 are E1 channel occupied by sub-card, 9-10 are channels used to transmit E1 network management information.
OPCOM3105 provides 2 commands for timeslot assigning. Users can choose whether assign timeslot according to backboard timeslot, if only input SDH timeslot number, system will assign one piece of backboard timeslot automatically.
Example: 1. Add VC12 timeslot 1 to SDH optical interface 1 at EOS interface 1: OPCOM3105# config OPCOM3105(config-eos/1)#timeslot add sdh 1 vc12 1
Set successfully.
User Manual
3. Add VC12 timeslot 1 to SDH optical interface 1 at E1 interface 1: OPCOM3105(config-e1/1)# timeslot add sdh 1 vc12 1
Set successfully.
15
www.raisecom.com
User Manual
This chapter mainly introduces SDH protect-switch configuration. OPCOM3105 provides protection function based on SDH interface, and 1+1 path protection and multiplex section protection are available. Commands Config Description Enter global configuration mode. (enable|disable): enable: protection enable disable: protection disable. (path|ms): type of APS; OPCOM3105 SDH port protection in support of path protection and multiplex section protection. path: path protection; ms: multiplex section protection. Show APS status.
show aps
Configure APS mode command. aps-mode index <1-2> (nonrevertive|revertive) (nonrevertive|revertive): select APS mdoe; Nonrevertive: nonrevertive mode; revertive: revertive mode. Aps-restore-time index <1-2> time <0-12> Configure command for recovering time of APS.
Example: Enable SDH optical interface path protection: OPCOM3105# config OPCOM3105(config)# protect-switch enable type path Set successfully
16
www.raisecom.com
User Manual
This chapter is consisted of: Interface rate-limit Storm-control configuration MAC information configuration QOS function configuration
OPCOM3105 is in support of independent rate-limit based on interface, but only in support of bi-direction rate-limit. The granularity is 64kbps. Note: It is normal that the actual rate-limit may have a small windage with configured value because of limit of granularity. Configure interface 2 rate-limit to be 4000kbps: OPCOM3105(config-eswif/0/2)# rate-limit 4000
Set Successfully.
Configuration of storm-control rate. storm-control-global rate <62-8191> storm-control-global ( broadcast | Configuration of storm-control type. multicast | disable ) Show storm-control configuration information. show storm-control-global
17
www.raisecom.com
User Manual
Storm-control function is global control. The command locates under global configuration mode. Storm-control includes: broadcast-control, broadcast and multicast-control and storm-control disable. Example: OPCOM3105(config)# storm-control-global rate 4566
Set Successfully.
OPCOM3105 supports classified MAC address aging time configuration. No limit in parameters be input, system can classify the parameters automatically. Example: OPCOM3105(config)# mac-address-table aging-time 35
Set Successfully.
In the example, aging time is 0 means disable this function, use no command can also disable the mac-address-table aging-time function.
Use the command mac-address-table learning (enable | disable) can enable/disable MAC address table learning function. Example: disable learning function: OPCOM3105(config)# mac-address-table learning disable
18
www.raisecom.com
Set Successfully.
User Manual
Use the command [no] mac-polling can enable/disable mac polling function. Be noted that the show and search command can reflect correct MAC information only when mac-polling enable.
Add/delete static MAC address: OPCOM3105(config)# mac-address-table static 0002.3456.77ce vlan 101 port 2
Set Successfully.
Note: use the command mac-polling before show mac information. Otherwise the information may invalid or not correct. Or users can use the command search mac-address HHHH.HHHH.HHHH to search mac address information saved at local device, but users also need to execute mac-polling command to update local mac address table information.
OPCOM3105 supports queuing attemper based on priority weighted average. The function can use cos byte section priority or use interface priority configuration. When priority function disable, use port priority configuration by default and every interface is of the same priority. There are four different priorities in OPCOM3105 device. Users can use qos map cos-queue cos0 cos1 cos2 cos3 cos4 cos5 cos6 cos7 command to configure corresponding relation between cos value and priority.
19
User Manual
[no] qos trust cos command can used in configuration of choosing cos value or port privilege. If configured trust cos, device will allot privilege according to cos value. Example: OPCOM3105(config)# qos trust cos
Set Successfully.
Note: Priority configuration by default is realized by port COS value configuration. To modify mapping relation from cos to priority will affect the port priority configuration directly.
20
www.raisecom.com
User Manual
This chapter mainly introduces configuration of vlan. Related commands of vlan configuration: Commands [no] vlan <2-4094> state (active | suspend) switchport access vlan <2-4094> Description Create vlan or enter static vlan mode, no command can be used to delete vlan. Vlan working state.
Configure port to access mode, assign vlan for the port. Configure port to tunnel mode, assign vlan for the switchport dot1q-tunnel vlan <2-4094> port. Configure port to trunk mode; assign vlan switchport trunk allowed vlan list allowed by the port. Configure port to hybrid mode; assign vlan switchport hybrid allowed vlan list allowed by the port. switchport mode (access | Configure port mode, without change port vlan id. dot1q-tunnel) switchport vlan <2-4094> Configure port vlan id, without change port mode. show vlan [<2-4094>] Show vlan configuration information.
OPCOM3105 supports vlan configuration management function based on 802.1Q recommendation. Only single tag type configuration is in support here. Since vlan resource of the device is limited, it supports 11 user configured vlan and 4 default vlan at one time. When vlan resources are used out, release the already existed vlan before configure new vlan. The 4 default vlan are: vlan1 includes interface and defaulted vlan of every port. Defaulted vlan are always existed. If one port belongs to its defaulted vlan, it can not be deleted. The 4 standard interface types are: access port, tunnel port, trunk port and hybrid port. Users can configure one port type and assign vlan for the port. If destination vlan is not existed, system creates a vlan to meet the configuration request. Configuration wont be effective and lack of printing resource information will display if all vlan resources are exhausted. Example: OPCOM3105(config-eswif/0/2)# sw trunk allowed vlan 301-305
Set Successfully.
Users can use vlan command to enter static vlan mode, if the vlan is not existed, system checks vlan resource and create the vlan or show resource exhausted. OPCOM3105(config-vlan300)# vlan 301 OPCOM3105(config-vlan301)#
21
User Manual
Use state command to modify vlan state for the vlan that is existed: OPCOM3105(config-vlan302)# state suspend
Set Successfully.
Besides, users can modify port mode without change port belonged vlan (command switchport mode (access | dot1q-tunnel)), or modify port belonged vlan without change port mode (command switchport vlan <2-4094>).
22
www.raisecom.com
User Manual
This chapter is consisted of: Overview Point-to-point topology Chain topology Ring topology
9.1 Overview
OPCOM3105 provides bi-direction aggregation interface and Ethernet and E1 tributary interface. It is flexible to build network topology for meeting complicated structure in client accessing, as the below figure shows.
TM device can form point to point non-protection network, and double TMs can form a 1+1 path protection of STM-1 level. When configured as 1+1 protection mode, the two optical interfaces can protect each other to enhance service reliability.
TM device and ADM device can form a non-protection chain topology network, and double optical interface TM device and ADM device can form 1+1 protection chain of STM-1 level. When configured as 1+1 protection mode, service reliability will enhance.
23
www.raisecom.com
User Manual
9.4.1 2F SNC-P
The advantages of 2F SNC-P are high speed, flexibility and all level capacities. The switching depends on local environment and has nothing to do with the network topology, so 2F SNC-P is suitable for all kinds topologies, especially dynamic network. The disadvantage of 2F SNC-P is that all the tributaries in the ring are all APS architectures, that is between any two points, there are two transmission lines transmitting the data bi-directionally, and every receiving node receives the data bi-directionally. So the total service flow is lower than the device capacity. 2F SNC-P is suitable for access network, relay network and long distance network, which are concentrated, low service flow.
24
www.raisecom.com
User Manual
Chapter 10
Typical Application
OPCOM3105 is typical applied as remote device of OPCOM3500E SDH tributary module to supply SDH access for Ethernet and E1 service.
25
www.raisecom.com
OPCOM3105-B snmp ip: 192.168.5.28
User Manual
DCC1 ip 192.168.5.2
OPCOM3105-A
DCC1 ip 192.168.6.2
3 OPCOM3105 devices are used here to build ring network, the configuration of every device shows as the figure.
Configure DCC interface IP on OPCOM3105-A: Commands OPCOM3105#config OPCOM3105(config)# interface dcc 1 OPCOM3105(config)#ip address 192.168.5.1 OPCOM3105(config)#interface dcc 2 OPCOM3105(config)#ip address 192.168.6.1 OPCOM3105(config)# router rip Description Enter global configuration mode Enter dcc interface 1 Configure dcc1 ip 192.168.5.1 Enter dcc interface 2 Configure dcc2 ip 192.168.6.1 Startup the rip router function.
Configure DCC interface IP on OPCOM3105-B: Commands OPCOM3105#config OPCOM3105(config)# interface dcc 1 OPCOM3105(config)#ip address 192.168.5.2 OPCOM3105(config)#interface dcc 2 OPCOM3105(config)#ip address 192.168.7.2 OPCOM3105(config)# router rip Description Enter global configuration mode Enter dcc interface 1 Configure dcc1 ip 192.168.5.2 Enter dcc interface 2 Configure dcc2 ip 192.168.7.2 Startup the rip router function.
26
www.raisecom.com Configure DCC interface IP on OPCOM3105-C: Commands OPCOM3105#config OPCOM3105(config)# interface dcc 1 OPCOM3105(config)#ip address 192.168.6.2 OPCOM3105(config)#interface dcc 2 OPCOM3105(config)#ip address 192.168.7.1 OPCOM3105(config)# router rip Description Enter global configuration mode Enter dcc interface 1 Configure dcc1 ip 192.168.6.2 Enter dcc interface 2 Configure dcc2 ip 192.168.7.1 Startup the rip router function.
User Manual
The network management station gateway to configure at last is the direct connected OPCOM3105-A IP address 192.168.4.28. (this configuration asks for users guarantee there is no IP address of network segment 10 and 11 at the network station, otherwise the message that with destination IP address belong to these two network segments will not able to transmit to default gateway.) Ping 192.168.5.28 and 192.168.6.28 must be successful on OPCOM3105-A after configuration successfully, and network management host can access 192.168.5.28 and 192.168.6.28 to realize management of other devices. If one path of network management has fault, the host can manage other devices by alternative router. Selection of router is automatically operated in accordance with devices rip.
Typical Point-to-Point network management path application as the below figure shows:
Configure DCC interface IP on OPCOM3105-A: Commands OPCOM3105#config OPCOM3105(config)# interface dcc 1 OPCOM3105(config)#ip address 192.168.6.1 OPCOM3105(config)#interface dcc 2 OPCOM3105(config)#ip address 192.168.7.1 OPCOM3105(config)# router rip Description Enter global configuration mode Enter dcc interface 1 Configure dcc1 ip 192.168.6.1 Enter dcc interface 2 Configure dcc2 ip 192.168.7.1 Startup the rip router function.
27
www.raisecom.com Configure DCC interface IP on OPCOM3105-B: Commands OPCOM3105#config OPCOM3105(config)# interface dcc 1 OPCOM3105(config)#ip address 192.168.6.2 OPCOM3105(config)#interface dcc 2 OPCOM3105(config)#ip address 192.168.7.2 OPCOM3105(config)# router rip Description Enter global configuration mode Enter dcc interface 1 Configure dcc1 ip 192.168.6.2 Enter dcc interface 2 Configure dcc2 ip 192.168.7.2 Startup the rip router function.
User Manual
At last, configure default gateway for network station to be direct connected OPCOM3105-A IP 192.168.4.28 (this configuration asks for users guarantee there is no IP address of network segment 10 at the network station, otherwise the message that with destination IP address belong to the network segments 10 will not able to transmit to default gateway.). Ping 192.168.10.28 must be successful on OPCOM3105-A after configuration successfully, and network management host can access 192.168.10.28 to realize management of other devices. If east optical port of network management has fault, the network management data will shift to western optical port of DCC2 by automation.
28
www.raisecom.com
User Manual
Appendix A Acronyms
Acronyms ADM AIS APS AU AU-n AUG AU-PTR BBE BBER BER CMI C-n CORBA CV DCC DCE DCF DCN DDN DTE DXC ECC EM Acronyms EML EMS EOS ES ESR ETSI FEBBE FEES
Full spelling Add-Drop Multiplexer Alarm Indication Signal Automatic Protection Switching Administrative Unit Administration Unitlevel n Administration Unit Group Administration Unit Pointer Background Block Error Background Block Error Ratio Bit Error Ratio Coded Mark Inversion Container- n Common Object Request Broker Architecture Code Violation Data Communications Channel Data Circuit-terminating Equipment Data Communications Function Data Communications Network Digital Data Network Data Terminal Equipment Digital Cross Connect Embedded Control Channel Element Management Full spelling Element Management Layer Element Management System Ethernet Over SDH Error Second Error Second Ratio European Telecommunication Standards Institute Far End Background Block Error Far End Error Second
29
www.raisecom.com FESES GUI HDLC HPC IP ITU-T L2 LAN LCT LOF LOP LOS LPC MAC MAN MCU MD MF MII MM MS Acronyms MS-AIS MSOH MSP NE NEF NEL NML NMS OAM OFS OOF OS OSI PCM PDH Far End Severely Error Second Graphical User Interface High Digital Link Control Higher order Path Connection Internet Protocol International Telecommunication Union-Telecommunication Standardization Sector Layer 2 Local Area Network Local Craft Terminal Loss Of Frame Loss Of Pointer Loss Of Signal Lower order Path Connection Medium Access Control Metropolitan Area Network Micro Control Unit Mediation Device Mediation Function Medium Independent Interface Multi Mode Multiplex Section Full spelling Multiplex Sections - Alarm Indication Signal Multiplex Section OverHead Multiplex Section Protection Network Element Network Element Function Network Element Layer Network Manager Layer Network Management System Operation,Administration and Maintenance Out of Frame Second Out of Frame Operation System Open System Interconnect Pulse Code Modulation Plesiochronous Digital Hierarchy
User Manual
30
www.raisecom.com PJE+ PJEPOH PPP PRC RAM RDI REI REG RFI RIP Acronyms RMII RS RSOH SDH SEC SES SESR SETS SM SNCP SOH SPRING SSM STM-N TCP TDEV TDM TM TMN TU TU-m TUG-m UAS VC Pointer Justification Event + Pointer Justification Event Path OverHead Point to Point Protocol Primary Reference Clock Random Access Memory Remote Defect Indication Remote Error Indication Regenerator Remote Failure Indication Router Information Protocol Full spelling Reduced Medium Independent Interface Regenerator Section Regenerator Section OverHead Synchronous Digital Hierarchy SDH Equipment Clock Severely Error Second Severely Error Second Ratio Synchronous Equipment Timing Source Single Mode Sub network Connection Protection Section Overhead Shared Protection Ring Synchronous State Message Synchronous Transport Module Level-N Transport Control Protocol Time Deviation Time Division Multiplex Terminal Multiplexer Telecommunications Management Network Tributary Unit Tributary Unitlevel m Tributary Unit Grouplevel m Unavailable Second Virtual Container
User Manual
31
www.raisecom.com VC-n VLAN WAN Virtual Containerlevel n Virtual Local Area Network Wide Area Network
User Manual
32
Address: 2nd Floor, South Building of Rainbow Plaza, No.11 Shangdi Information Road, Haidian District, Beijing Postcode: 100085 Tel: +86-10-82883305 Fax: +86-10-82883056 Email: export@raisecom.com http://www.raisecom.com