Beruflich Dokumente
Kultur Dokumente
VAPOR DIFFUSIVITY
AIM :
To determine the diffusivity of the given organic solvent.
THEORY :
The diffusion operations always involve the contact of fluid, either gas or liquid with another
phase accompanied by transfer of material between the contacted phase. It is desirable to maintain
the contacted phase in relative motion with respect to one another. Molecular diffusion is the
transport of matter on a molecular scale through a fluid, which is stagnant, or if in laminar flow in a
direction perpendicular to the flowing streamlines. The diffusion of vapor A, from a volatile liquid
into another gas B (here air) can be conveniently studied by confining a small sample of the liquid
in a narrow vertical tube and observing its rate of evaporation into a stream of gas B passed across
the top of the tube.
The apparatus consists essentially a glass capillary tube placed in a transparent sided temperature
controlled water bath. A horizontal glass tube is fixed to the upper end of the capillary tube and air
is blown through this by a small air blower included with in the unit.
The arrangement allows the maintenance of a partial pressure difference within the capillary tube
between the evaporating liquid surface and the flowing air stream. A traveling microscope, with
sliding vernier scale is mounted on a rigid stand along side the thermostatic bath and is used to
measure the rate of fall of the solvent or air meniscus with in the capillary. The diffusivity cell used
here is a case of pseudo steady state diffusion in which one of the boundaries shift with time with
the effect that the length of the diffusion path changes though only by a small amount over a long
period of exposure.
Air(B) Air(B)
Z1 Z2
1
Org. solvent
Org.Solvent
Final liquid level
PROCEDURE :
Fill the water bath with water, switch on the stirrer. Heat the water to the desired
temperature by adjusting the thermostat. Fill the capillary tube with the given organic
solvent, say, carbon tetrachloride or acetone (to the level of about 75%) and replace the
capillary tube. Note down the initial liquid level in the capillary tube using vertical traveling
microscope. Allow the air to flow continuously over the capillary tube, to maintain zero
partial of the vapor at the top of the capillary tube. Let the experiment run in this fashion for
an hour and note down the liquid level in the capillary tube using vertical traveling
microscope at interval of every ten minutes. Repeat the experiment with atleast three
different bath temperatures of 50, 60, 70
0
C and plot the diffusion co-efficient against
temperature on a log-log sheet and confirm that the slope is 3/2.since DAB is proportional to
T
3/2
(
t
AB
P
T
D
2
3
).
Compare the experimental value with the theoretical value calculated from Wilke-Lee
equation:
DAB=
( )
,
_
,
_
AB
AB t
B A B A
KT
f r P
M M
T
M M
2
2
3
4
1 1 1 1
249 . 0 084 . 1 10
CALCULATIONS :
Refer fig. At t = 0, z = z1 (Initial height)
t = t , z = z 2 = z1 + z at t = t ;
since the flow of air is continuous , the concentration of the organic solvent at the top of the tube is
zero.
Density of solvent at room temp. () = _______
Vapor pressure of solvent at room temp.(PA1)= ____.
PB1 = Pt-PA1 = 760 - PA1 mmHg.
At Z=Z2 , the vapor pressure of solvent at air-solvent interface = 0 this means that PA,2 = 0.
2
PB,2 = Pt-PA,2 = 760mmHg.
PB,ln =
( )
,
_
1 ,
2 ,
1 , ,
ln
B
B
B Z B
P
P
P P
.
( )
2
.
1
. .
2
2
2
1
,
2 , 1 ,
ln
Z Z
M
P
t P P
P RT
P
Z
D
L A
B B
B
AB
3
2. LIQUID DIFFUSION
AIM :
To determine the diffusion coefficient of Sulphuric acid in Water.
THEORY :
The diffusional operations always involve the contact of fluid, either gas or liquid with another
phase accompanied by transfer of material between the contacted phase. It is desirable to maintain
the contacted phase in relative motion with respect to one another. Molecular diffusion is the
transport of matter on a molecular scale through a fluid, which is stagnant, or if in laminar flow in a
direction perpendicular to the flow.
PROCEDURE :
1. Take about 750ml of water in the beaker (note down the volume of water taken).
2. Fill the porous tube with about 150ml of dilute Sulphuric acid (known normality, say 0.05).
3. Allow the diffusion to continue for an hour. Note down the final volume of water in the beaker
and also the volume in the porous tube.
4. Find the normality of H2SO4 in the beaker and also normality of H2SO4 in the porous tube.
CALCULATIONS :
1. Standardize sodium hydroxide using 0.05 N oxalic acid.
2. Using the standardized sodium hydroxide (around 0.05 N), standardize H2SO4 .
3. After one hour titrate the solution in the beaker and the porous tube.
4. Initial volume of pure H2SO4 in the porous tube (Suppose 150 ml of 0.05 N H2SO4 is taken,
the volume of pure H2SO4 present in this 150 ml.)
Normality of H2SO4 = _____
Density of H2SO4 at room temperature = _________
Volume of H2SO4 in the porous tube = _________
4
Weight of H2SO4 = [N x mol. Wt . x vol taken] / [2 x 1000]
Volume of H2SO4 = weight / density
5. Volume of H2SO4 in the porous tube after diffusion = _________ ml.
Normality of H2SO4 after diffusion = ________ N
Weight of H2SO4 = [N x mol.wt. x vol.] / [2 x 1000] = ____ gm.
Moles of H2SO4 = wt. / mol.wt.
Volume of H2SO4 = weight / density (Q)
Volume of H2O in porous tube = P Q
Weight of H2O = volume x density
Moles of water = wt. of water / mol. Wt
Mole fraction of water in porous column,
XA1 = No.of moles of H2SO4/ No.of moles H2SO4+ moles of H2O
XB1 = 1 XA1
1 = weight/volume = [wt. Of H2SO4 + wt. Of H2O]/[vol.of H2SO4 + vol.of
H2O] or can be determined using specific gravity bottle.
M1 = average mol. Wt.= (XA1) (mol.wt. of H2SO4) + (XB1)( mol.wt. of H2O) Calculate (/M)1
IN BEAKER:
Volume of solution in beaker = ______ ml.
Normality of solution = _____ N
Moles of H2SO4 = [Nor. X Volume]/[2 x 1000] = ______ moles
Weight of H2SO4 = moles x mol.wt. = _____ gm
Volume of H2SO4 = weight / density of H2SO4 = ____ ml.
Initial volume of water in beaker = ____ ml.
Weight = volume x density
No. of moles = weight / mol.wt.
Mole fraction XA2 = [ moles of H2SO4]/ [ moles of H2SO4 + moles of H2O]
XB2 = 1 XA2 ; 2 = Weight / volume or find out using specific gravity bottle
M2 = average mol. Wt. = (XA2) (mol.wt. of H2SO4) + (XB2)( mol.wt. of H2O)
5
Calculate (/M)2 = ____
Determine (/M)avg. = [(/M)1+(/M)2]/2
Calculate, XBM = [XB1 XB2] / ln(XB1/XB2)
(a) Initial moles of H2SO4 in the porous tube = ______
(b) After diffusion number of moles of H2SO4 in porous tube = ______
Drop in moles of H2SO4 = (a) (b)
Increase in moles of H2SO4 in beaker = _____ moles
Moles of H2SO4 transferred =[Drop in moles of H2SO4 incr. in moles
of H2SO4 in beaker]/2
NA = no.of moles of H2SO4 transferred/ [DL x time]
D = diameter of the column; L = length of the column; Time = 3600s
NA = {(DAB/Z)( (/M)avg [(XA1 XA2)/ XBM] }; Calculate diffusivity
from the above equation.
Compare the result with Wilke Chang equation:
DAB
o
= [(117.3 x 10
-8
)(MB)
0.5
T] / [ VA
0.6
]
6
3. SIMPLE DISTILLATION
AIM: To verify the Rayleighs law by carrying out differential distillation for a given binary
mixture.
THEORY:
In a simple batch distillation or differential distillation a liquid mixture is slowly boiled in a
kettle. The vapors are removed immediately as soon as they are formed. The distillate is
then collected from the condenser. During the early part of vaporization the distillate is rich
in A, but as time proceeds, it becomes leaner in A.
Consider a batch of L1 moles of a liquid mixture consisting of components A and B in he
still and x1 be the mole fraction of A in the still. At any given time during distillation, there
are L moles of liquid left in the still and x and y are the mole fractions of A in liquid and
vapor respectively. A very small amount of liquid dL is vaporized. The composition is from
x to x-dx and the change in the amount of liquid is from L to L-dL.
Material balance for the component A gives,
xL = (x-dx)(L-dL) + y dL or xL = xL x dL Ldx + dx dL + y dL
Neglecting dx dL , the equation may be written as , dL / L = dx / (y-x)
Integrating, ln F/W =
xF
xw
x y
dx
*
; where , F= original moles in the still.
W= moles left in the still
The integration of Rayleigh equation can carried out graphically from the equilibrium curve,
by plotting 1 / (y* - x) vs x as follows:
Y3
*
Y2
*
Y
Y1
*
x1x2 x3
7
x
Plot 1/ (y
*
-x) vs x :
1/(y*-x)
xw xF
x
If LHS = RHS, Rayleigh law is verifed.
OBSERVATIONS:
Initial quantity of feed taken = ml
Vol x density = weight of distillate
Volume of distillate collected = ml
Density =
volume x density = weight
Volume of bottoms = feed distillate= ___ ml.
Volume x density = weight
8
x
ALTERNATIVE METHOD:
We know that Y * = x / [1+ ( - 1)x] assuming as an ideal mixture with constant relative
volatility.
Raleigh equation for this case is ln [FxF/ Wxw] = ln {[F(1-xF)/ W(1-xw)]}
9
4. BATCH DISTILLATION WITH RECTIFICATION
AIM:
To find determine the height equivalent to theoretical plate (HETP) and the capacity
coefficient for the given system using packed distillation tower.
THEORY:
The vapor produced during differential distillation is removed as fast as it is formed and as
a method of separation this technique is not very effective. In order to ensure a high
degree of separation and simultaneously obtaining a high degree of enrichment by simple
distillation, one good method is to distill both the residual liquid and the overhead products.
This can be accomplished by a repetition of simple distillation. There is yet another way, a
better one indeed, to obtain a high degree of separation. This is the method o using reflux
i.e., batch still is hooked up with a rectifying column to establish reflux policy. This method
is particularly useful to obtain products with a narrow range of composition.
PROCEDURE:
Charge the still with the given organic mixture and measure the composition by measuring
the density.Adjust the thermostat to 80
0
C, allow the mixture to boil for half an hour under
total reflux conditions.Measure the flow rate of the condensate, note down the time taken
to collect 10 ml of the condensate. Measure the composition of the condensate by
measuring the density.
Measure the composition of the bottoms.
Note down the temperature indicated by the thermometer.
10
CALCULATIONS:
Find out the number of trays required for the same separation using Mc Cabe thiele method.
Height of the column is one meter.
Height equivalent to theoretical plate can be calculated from height of the column and number of
theoretical plates as follows: HETP = Z / (n-1)
Z = NtoG . HtoG
NtoG = (y1 y2) / {[(y y1
*
)-(y- y2
*
)] / [ln (y y1
*
)/(y- y2
*
)}
{Plot the equilibrium curve and find the equilibrium values for feed and condensate}
Capacity coefficient, Kya = G / HtoG ; where G is the mass flow rate of condensate.
HtoG = Z / NtoG
Result: HETP = ___ ; HtoG= ; NtoG = ; Capacity Coefficient =
11
5. SOLID LIQUID EQUILIBRIUM
AIM:
To generate the solid liquid equilibrium data.
THEORY:
Solid liquid extraction is most widely used in metallurgical industries.Most useful minerals occurs
in mixtures with large proportions of undesirable constituents, and leaching of the valuable material
is a separation method which is applied. For example copper minerals are preferentially dissolved
from certain of their ores by leaching with sulphuric acid or ammoniacal solutions, and gold is
separated from its ores with the aid of sodium cyanide solutions. Leaching similarly plays an
important part in the metallurgical processing of alumina, cobalt, manganese, nickel, and zinc.
Many naturally occurring organic products are separated from their original structure by leaching.
For example sugar is leached from sugar beets with hot water, vegetable oils are recovered from
seeds such as soybeans and cotton seed by leaching with organic solvents, tannin is dissolved out
of various tree barks by leaching with water, and many pharmaceutical products are similarly
recovered from plant roots and leaves. Tea and coffee are prepared both domestically and
industrially by leaching operations.
PROCEDURE:
Take 5 beakers and number them as (i), (ii),(iii) (iv) &(v). Add 40gm of calcium carbonate and l00ml
of distilled water to each flask. Add around 2, 4, 6, 8 & l0gm of NaOH to (i), (ii),(iii) (iv) &(v)
respectively.
Stir the contents of the flask and allow the mixture to stand for 15- 20min.
Separate the liquid portion by filtration using filter paper. Measure the volume of the filtered liquid.
Measure the density of the filtrate using specific gravity bottle.
Take 10mlof the liquid and titrate against oxalic acid of known Normality (0.5N).
Calculate normality of sodium carbonate.
12
Note down the density of water at room temperature.
CALCULATIONS:
Normality of oxalic acid =
Normality of Na2CO3 =
Wt. of Na2CO3 in liquid phase = Normality*Vol. of filtrate* EqWt./1000
Wt. of Na2CO3 in solid phase = Original Wt. - Wt. of Na2CO3 in liquid phase
Wt. of water in solid phase,
X = Wt. of Na2CO3/ Wt. of Na2CO3+ Wt of H2O Liquid Phase
Nx = Wt. of calcium carbonate/ Wt. of Na2CO3 + Wt. of H2O
Y = Wt. of Na2CO3/ Wt. of Na2CO3+ Wt.of H2O Solid Phase
NY = Wt of calcium carbonate / Wt. of Na2CO3 + Wt of H2O
Measure of density of the decanted mixture,
Volume x mixture
100
2O) H 3COOH CH CHCl3 ( Weight
2O H of Weight
2O H of % Weight x
+ +
100
2O) H 3COOH CH (CHCl3 Weight
3COOH CH of Weight
acid Acetic of % Weight x
+ +
SET1:
H2O (A) Chloroform (B) Acetic acid (C)
Vol. Wt. Wt.% Vol. Wt. Wt.% Vol.. Wt. Wt.%
SET2:
H2O (A) Acetic acid (C) Chloroform (B)
Vol. Wt. Wt.% Vol. Wt. Wt.% Vol.. Wt. Wt.%
Prepare a binodal curve using the above data and compare with the literature values.
18
DATA:
Solubility of Chloroform in 10 ml of water = 0.3ml
Solubility of water in 10 ml of Chloroform = 0.6ml
Standard values:
H2O at room temp = ------ gm/cc
CHCl3 at room temp = ----- gm/cc
CH3COOH at room temp = -------gm/cc
NOTE: Determine density using specific gravity bottle.
Extract Phase(Wt%): Raffinate Phase(Wt.%)
HCl3 H2O CH3COOH CHCl3 H2O CH3COOH
0.84 99.16 0 99.01 0.99 0
1.21 73.64 25.1 91.85 1.38 6.77
7.3 48.58 49.12 85 2.28 12.72
15.11 34.71 50.18 70.13 4.12 25.72
18.33 31.11 50.56 67.15 5.2 27.65
25.2 25.34 49.41 39.55 7.93 32.08
28.88 23.25 47.87 55.81 9.58 34.67
19
8. WETTED WALL COLUMN
AIM:
To determine the mass transfer coefficient (gas phase) at different
Reynolds numbers in wetted wall column for Air Water system.
THEORY:
A great deal of effort have been devoted in the literature to developing analogies among three
transport processes for turbulent transfer so as to allow prediction of one from any of the others.
The most successful and most widely used analogy is based on experimental data for gases and
liquids in both the laminar and turbulent flow region as
[ ] ( ) 3
2
.
3
2
Pr
2
Sc
avg
c
d
P
h
N
V
K
J N
G C
h
J
f
In order to derive the mass transfer coefficient in laminar flow, theoretical expressions may be
used, since the equations for momentum transfer and diffusion can be solved.
When a fluid is flowing in laminar flow and mass transfer by momentum diffusion is occurring, the
equations are very similar to those for heat transfer by conduction in laminar flow, though the
phenomenon of heat and mass transfer are not always completely analogous, since in mass
transfer several components may be diffusing.
Also the flux of mass perpendicular to the direction of the flow must be small so as not to distort the
laminar velocity profile. So, in many actual cases it is difficult to describe mathematically even
laminar flow. Hence, experimental mass transfer coefficient are often obtained and correlated for
different flowing conditions.
In wetted wall column, a volatile pure liquid is permitted to blow down the inside surface of a
circular pipe while a gas is flown upward or downward through the central case. Measurement of
the rate of evaporation of the liquid into the gas stream over the known surface permits calculations
of mass transfer coefficients for the gas phase in wetted wall column is highly dependent on
surface conditions. Since the liquid may be pure liquids, the concentration gradient for the diffusion
exists entirely within the gas stream and coefficient Kg may be obtained directly from the data. Use
of different gases and liquids provides variation of Nsc.
In this way, Sherwood and Gilliland covered values of NRe from 2000 to 35000 and gas pressure
range from 0.1 to 3 atm. and proposed for turbulent flow
20
( ) ( )
33 . 0 83 . 0
Re
023 . 0
Sc Sh
N N N ---------------- (1)
This equation holds for Nsc of 0.6 to 3000, though Nsc for gases is in the range of 0.5 -3.0 and for
liquid is above 100 in general.
(1) may be rewritten as
33 . 0 83 . 0
023 . 0
,
_
,
_
AB AB
BM G
D
Du
D
D
P
p K
----------------- (2)
The gas pressure drop from this type of equipment is very low, however, since it is almost entirely
confined to skin friction effects with few or no expansion or contraction losses. This equation
describes all the data for both liquids and gas flow rate.
This empirical relation is quite remarkable in the manner in which it generally confirms the
relationship between heat, mass and momentum transfer developed theoretically. It should be
noted that the evaporation of the volatile liquids in a wetted wall column results in cooling of the
liquids and a consequent simultaneous heat transfer between liquid and gas. The heat transfer
rates are somewhat higher, owing to turbulence caused by ripples and waves on the liquid surface,
than the given by the equation,
( ) ( )
3 . 0
Pr
8 . 0
Re
023 . 0 N N
K
hD
Wetted wall column are used for theoretical studies for mass transfer because the interfacial
surface between the phases is kept under control and is measurable. These have also been used
successfully as absorbers for hydrochloric acid gas, ammonia, acetone, benzene and other volatile
liquids.
PROCEDURE:
The apparatus consists of a wetted wall column with an inlet and out let for air. At both inlet and
outlet, two thermometers for measuring the dry and wet bulb temperatures. Air is supplied with the
help of a compressor. Rotameters are provided for measuring the flow rate of air and water.
Initially water flow rate is adjusted to be laminar (no ripples are formed). Then by changing the flow
rate of air through the column, dry bulb and wet bulb temperatures are noted down. This
procedure is repeated for five different airflow rates.
21
OBSERVATIONS:
S.No Flow rate Inlet air temp. Outlet air temp.
Air Water WBT DBT WBT DBT
1.
2.
3.
4.
5.
WBT:Wet bulb temperature.
DBT: Dry bulb temperature.
DATA:
Length of the column, L = 1000mm
Internal diameter of the tube = 33mm
Wetted surface in the column,A(m
2
) = *d*L
Average air temperature = [inlet DBT +outlet DBT] / 2
Molar Air flow rate (kmol/s) = (Air flow rate in LPM * 10
-3
)
*[273/(273+Tav)][1/22.4][1/60]
Total pressure in the column = 101.3kN/m
2
(P)lm = (P2 - P1)/ ln(P2/ P1)
P1 = PAi PA1
PAi = vapor pressure of water at the inlet air temp.
PA1 = partial pressure of air at the inlet absolute
Humidity(= Y1Pt/ [1+Y1])
P2 = PAi PA2
PAi = vapor pressure of water at the outlet air temp.
PA2 = partial pressure of air at the outlet absolute
Humidity. (= Y2Pt/ [1+Y2])
(P)Bm = [(Pt PA1)- (Pt PA2)]/ {ln[(Pt PA1)/(Pt PA2)]
P = PAi PA1
NA = KG (P)ln
NA = Ms (Y2-Y1)/ *d*L
22
Ms = Molar flow rate of dry air = (actual flow Rate)/(1+Y1)
Kc
1
= KG (P)Bm RT/Pt
NRe = d QA/(A) air
D = diameter of the column,m
A = cross sectional area of the column
QA = air mass velocity, kg/s
air = Kinematic viscosity, m
2
/s
PA,i = vapor pressure of water vapor corresponding to the in let and out
let temperature. This can be determined by using Antoine
Equation,
ln P1
sat
= 16.2887-[3816.44/(T-46.13)]; where PAi
sat
is in Kpa
and T in
o
K
(OR) taken from literature at the desired temperature.
Absolute Humidity: Determined from the humidity charts at the inlet and outlet wet bulb and dry
bulb temperatures.
NA = Molar flux; KG = Gas phase mass transfer coefficient.
Temp. Air viscosity Air density air water density sat.vap.pr.
(
0
K) (Kg/ms) (Kg/m
3
) (m
2
/s) (Kg/m
3
) (Pa)
311 19x10
-6
1.135 16.76x10
-6
992.9 6628
299 18.4x10
-6
1.181 15.62x10
-6
996.7 3413
287 17.8x10
-6
1.230 14.52x10
-6
999.1 1653
23
9. VAPOR LIQUID EQUILIBRIUM DATA
AIM:
To generate the vapor liquid equilibrium data of a given system and compare with the
standard values.
THEORY:
Distillation is a technique used for separating components of liquid mixtures based on the boiling
point difference. In a closed system the vapor liberated from a liquid mixture will be in equilibrium
and the composition depends on the temperature and the pressure. At equilibrium the composition
of the liquid will be different from the composition of the vapor. When a liquid mixture of two
components is distilled and the liquid is kept in contact with the liquid for a long time equilibrium is
reached. The liquid will be richer in the more volatile component than in the liquid and the
concentration depends on the concentration of the liquid phase. The relation between the
concentration of any component in liquid phase(x) and concentration of any component in vapor
phase(y) at equilibrium gives the vapor liquid equilibrium curve, which is determined at the boiling
point, corresponding to particular pressure.
For a binary solution, according to the phase rule if pressure is fixed, only one variable can be set.
If we set the liquid composition (x), the temp. the vapor composition(y) is automatically set.
A diagram representing the boiling point of a mixture of the liquid, completely miscible with each
other, against the composition of vapor and liquid in equilibrium is called boiling point diagram. The
boiling points are plotted as the ordinates and the mole fraction of the more volatile component in
vapor and liquid as abscissa. The upper line is saturated vapor line (dew point line) and the lower
is the saturated line (bubble point line) represents the vapor and liquid compositions respectively
any point above the upper curve represents the entire vapor phase and any point below lower
curve represents entire liquid phase. Points between the two curves represent the partially vapor
and partially liquid state of the mixture.
PROCEDURE:
24
1) Charge the still with the given feed mixture (ethanol-water). Find the composition of the feed by
determining the density using specific gravity bottle, record the composition from the calibration
graph.
2) Heat the mixture to the boiling temperature and allow the condensate to reflux for 2 or 3 times
and record the composition of the condensate for the 4
th
condensate.
3) After finding the composition (4
th
condensate), allow the condensate to reflux back to the still.
4) Repeat to determine the composition of the condensate till it is same for three successive
condensates. Constant condensate composition is recorded.
5) Record the boiling temperature with the help of the thermometer provided.
OBSERVATIONS:
Feed composition Condensate composition
XA YA
XB YB
P = Atmospheric pressure.
T = Temperature .
Assumptions: Vapor phase is ideal gas mixture.
Liquid phase is non-ideal solution.
From T, find
sat
B
sat
A
P P , either from Antoin equation or Perrys Handbook.
Find Van-Laar Constants.
A =
( )
( )
exp
exp
exp
ln
ln 1
ln
A A
B B
A
X
X
+
----------------- (1)
B =
( )
( )
exp
exp
exp
ln
ln 1
ln
B B
A A
B
X
X
+
------------------- (2)
Calculate exp by modified Raoults law, with the help of experimental data (XA, YA, XB, YB)
exp A A
sat
A A
X P P y
------------------- (3)
25
exp B B
sat
B B
X P P y
-------------------- (4)
Now A and B are known.
USING VAN-LAAR EQUATIONS:
( )
2
2
ln
,
_
B
B
A
X
B
A
AX
---------------- (5)
( )
2
ln
,
_
B A
A
B
X
A
B
X
BX
--------------- (6)
by assuming, XA = 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, 1.0
XB = 0.9, 0.8, 0.7, 0.6, 0.5, 0.4, 0.3, 0.2, 0.1, 0.0
Calculate the corresponding A and B for different values of XA and XB
Using the values of A , B, XA and XB find the values of YA and YB
YA =
P
P X
sat
A A A
YB =
P
P X
sat
B B B
1
]
1
1
]
1
al Experiment
B
A
W
W
[volume of water in distillate x A] / [vol. Of aniline in distillate x B
Theoretical Steam condensed
Ws = 1/B [WF CPA (TSDT - Ti) + A WA + w WB ]
A = 113.728 KJ / Kg ; B = 2352 KJ / Kg ; CPA = 2.224 KJ /Kg
0
C at 32
0
C
Steam consumption = theoretical steam condensed i.e., (Ws) / [vol. Of aniline in distillate x (A)]
30
RESULT:
Atm.pr.
1. Experimental WB / WA PT Vs T
2. Theoretical WB / WA PB Vs T
3. Steam consumption VPB
4. Vaporization efficiency = {[2]/[1] } x 100
PA Vs T
P
(mm Hg)
VPA
TSDT
Temp. (
0
C)
31
11. TRAY DRIER
Aim:
To determine the drying characteristics of given solid material, to find the drying coefficient.
THEORY:
When wet sample is placed in contact with air, water evaporates from its surface and diffuses as
vapor through the air film that covers the surface. The concentration of moisture at the surface is
decreased, a concentration difference is set up and moisture then diffuses from the interior to the
surface of the slab or it moves to the surface as rapidly as it can vaporize from the surface, the rate
of drying is independent of the moisture content of the slab and is constant providing that the air
velocity, temperature and humidity do not change.
During this constant rate period the rate of drying is controlled by the rate of vapor diffusion through
the air film and is, therefore, dependent upon the humidity difference across the film and the
thickness of the film.
However, when the moisture content becomes less than a certain value known as the critical
moisture content, moisture can no longer move to the surface as rapidly as it could be vaporized
from the surface. The drying rate begins to fall and continues to fall with decreasing moisture
content until the equilibrium moisture content is reached and no further drying is possible under the
particular drying conditions.
PROCEDURE:
Weigh 100 gm of saw dust (50 gm in each tray) and wet the solid with 50 ml of water in each tray
and distribute the solid uniformly in the trays. Note down the initial weight of empty tray . The hot
air is adjusted to blow at 80
0
C (by setting the temperature). Note down the inlet and outlet wet
bulb and dry bulb temperatures. Ensure the wick is always kept wet with help of the provision
provided with the system. Note down the energy requirement .
All the above readings are taken for every ten minutes till the constant weight is obtained or steady
state is reached. Finally note down the air velocity.
OBSERVATIONS:
S.NO
Time
(min)
Weight
(grams)
Inlet air temp.(
0
C) Out let air temp.(
0
C) Energy
input(kWH) Dry Wet Dry Wet
32
CALCULATIONS:
Air flow rate over the trays = air velocity x cross section of the drier
Loss in weight with time = weight of the sample at the previous reading weight of the sample at
the given time.
Plot weight of sample Vs time. Draw tangents at different points and find slopes to get dw/d
Free water content (gm/gm dry stock) =
[weight of sample weight of dry material] / weight of
dry material
Drying coefficient during the constant rate period, dw/d = Kg A (Hw - Hg)
(HW - Hg) = 0.26(tg-tw) / w
where, tg = average dry bulb temperature.
tw = average wet bulb temperature
w = latent heat of vaporization of water at tw = 2500 KJ / Kg
Tabular form of calculations:
S.No
Time(
) min.
Wt. of
sampl
e (W)
gm
(min.)
w
(gm)
w/
(gm/min)
- dX/d
gm
moisture/gm
dry solid min
Drying rate
(gm/hr.m
2
)
Free
water
(gm)
Free water
content
(gm
moisture/g
m dry
solid)
(X)
Drying rate or drying flux is calculated as , N = - [Ss / A] [dX/d]
Where Ss = kg of dry solid
A = drying surface area.
33
GRAPHS:
1. Plot X vs , draw the tangents at different values of X and find the slope, -dX/d
2. Plot drying flux Vs X., determine Nc, Xc.
3. Plot drying rates or flux Vs time()
RESULT:
1. The drying coefficient, gm water evaporated/ hr m
2
unit humidity difference.
2. The critical flux and the critical moisture content from plot no. (2).
Note: Measure the surface area of the trays.
Technical Specifications:
The drier is a two tray drier made from Stainless /steel 304(inner body) and powder coated mild
steel (outer body) The inner body of the unit is insulated with 25 mm glass wool and cladded with
powder coated mild steel sheet to minimize the heat losses to the surroundings. Dimensions of the
tray dryer are
(1) Drying chamber:Cross section 400mm*400mm*1000mm long
(2) Heater Box: Cross section 400mm*400mm and 400 mm long with 6 kW heaters
(3) Axial flow fan chamber:Cross section 400mm*400mm and 400mm long with axial flow
fan(0.25 HP, 3 phase motor).
(4) Capacity of the digital balance is 5 Kg.
34