Sie sind auf Seite 1von 1

CT

HEAT SEALABLE COEXTRUDED FILM

Sealing layer - TREATED

OPP core
Description Transparent BOPP film, both sides sealable with a broad sealing range. The seal initiation temperature (SIT) is 105 C on the untreated side
PROPERTIES UNIT
microns g/m m/kg DIN EN ISO 22861/2/3

Sealing layer

TEST METHOD
15 13.65 73.26 18* 16.38 61.05 20 18.20 54.95 25 22.75 43.96

VALUE
30 27.30 36.63 35 31.85 31.40 40 36.40 27.47 50 45.50 21.98

Properties High heat seal strength Excellent hot tack Good moisture barrier Superior optical properties Outstanding printing characteristics Typical Applications This film is designed for use in HFFS, VFFS and overwrapping applications either as a single web or in lamination to itself or to other substrates

Thickness Grammage Yield

TENSILE PROPERTIES
Tensile Strength Elongation Secant Modulus 100% Elastic Modulus 1% Tensile Strength Elongation MD MD MD MD TD TD N/mm % N/mm N/mm N/mm % ASTM D882 DIN EN ISO 527-1/3 170 210 110 1900 280 80 170 210 110 1900 280 80 170 220 110 1900 280 80 170 220 100 1900 280 80 170 230 100 1900 280 80 160 240 100 2000 270 85 160 250 90 2000 250 90 150 250 90 2000 250 90

OPTICAL PROPERTIES
Gloss 45 Haze gloss unit % ASTM D2457 ASTM D1003 1.6 1.6 1.8 1.8 85 2.0 2.0 2.0 2.0

THERMAL STABILITY
Shrinkage (hot air 130C - 5') MD TD % % 4 OPMA TC4a 2

SEALING
Sealing threshold Seal strength 130 C Untr/Untr Untr/Untr C g/cm OPMA TC4b 105 >= 200

COEFFICIENT OF FRICTION
untr / untr untr / Met dynamic dynamic ASTM D1894 DIN EN ISO 8295-04 0.30 0.20

PERMEABILITY
OTR WVTR WVTR 23C-0% r.h. 37.8C-100% r.h. 23C-85% r.h. cc/(m2 d atm) g/(m2 d) " ASTM D3985 ASTM F1249 DIN 53122 2200 8 1.7 2100 7 1.6 1900 6.5 1.4 1600 6 1.3 1300 5 1 1100 4 0.9 950 3.5 0.7 750 3 0.6

TREATMENT
Treatment level
*: thickness available on request

dyne/cm

ASTM D2578

38

Guidelines for storage of OPP film No special conditions are required fort the storage of OPP films, however it is recommended that dry conditions below 30C are employed to minimize any deterioration of film properties and surface treatment level. All OPP films should be allowed to reach operation room temperature for 24 hours before use. OPP films are suitable for use within 6 months from date of delivery Food contact Vibac CT complies to the requirements of EEC directives and FDA regulations Specific documentation and migration test results are available upon request The results obtained and above properties refer to average values of laboratory tests on samples of our standard production. It is understood that this entails no obligation and/or other responsability on our part. Customer should verify the suitability of the film for it's specific end use, therefore this document will not represent a product specification

Europe
Tel: +39 0975 68210 Fax:+39 0975 61664 e-mail: filmsales@vibac.it www.vibacgroup.com

Ed.: 2; rev.: 0; 15.12.2011 Revision reason: first emission

Das könnte Ihnen auch gefallen