Beruflich Dokumente
Kultur Dokumente
Introduction
E.g pressure P, temperature T, volume V, and mass m Properties that are independent of the mass of a system e.g temperature, pressure, density Properties whose values depend on size-or-extent-of the system e.g mass, total volume, total momentum Extensive properties per unit mass e.g specific volume (v=V/m) and specific total energy (e=E/m)
Intensive properties
Extensive properties
Specific properties
Introduction
m V T P m V T P m V T P
Intensive properties Extensive properties
Introduction
State postulate the state of a simple compressible system is completely specified by two independent, intensive properties
The number of molecules involved is immense, and the separation between them is normally negligible by comparison with the distances involved in the practical situation being studied Although the properties of a fluid arise from its molecular structure,engineering problem are usually concerned with the bulk behavior of fluids Under these conditions, it is usual to consider a fluid as a continuum - a hypothetical continuous substance and the conditions at a point as the average of a very large number of molecules surrounding that point within a distance which is large compared with the mean intermolecular distance
Density
Density is defined as mass per unit volume =m (kg/m3) V Specific volume is defined as volume per unit mass v = V = 1 (m3/kg) m Density of a substance, in general depends on temperature and pressure
Specific Gravity
Specific gravity or relative density is defined as the ratio of the density of a substance to the density of some standard substance at a specified temperature (usually water at 4oC, for which H O=1000 kg/m3) SG = H2O
2
Specific Gravity
Substance Water Blood Seawater Gasoline Ethyl Alcohol Mercury Wood Gold Bones Ice Air (at 1 atm) SG 1.0 1.05 1.025 0.7 0.79 13.6 0.3-0.9 19.2 1.7-2.0 0.92 0.0013
Specific Weight
Where, P = absolute pressure v = specific volume T = thermodynamic (absolute temperature) T(K) = T(oC) + 273.15 = gas density R = gas constant
Saturation temperature, Tsat the temperature at which a pure substance changes phase at a given pressure Saturation pressure, Psat the pressure at which a pure substance changes phase at a given temperature Vapor pressure, Pv of a pure substance the pressure exerted by its vapor in phase equilibrium with its liquid at a given temperature Partial pressure the pressure of a gas or vapor in a mixture with other gases
SME 1313 Fluid Mechanics I
Possibility of the liquid pressure in liquid-flow system dropping below the vapor pressure at some location, and resulting unplanned vaporization A fluid vaporizes when its pressure gets too low, or its temperature too high. All centrifugal pumps have a required head (pressure) at the suction side of the pump to prevent this vaporization. Suction cavitation occurs when the pump suction is under a low pressure/high vacuum condition where the liquid turns into a vapor at the eye of the pump impeller. Cavitation must be avoided in flow systems since it reduces performance, generates vibration and noise and causes damage to the equipment
Energy mechanical, thermal, kinetic, potential, electric, etc. Microscopic energy the forms of energy related to the molecular structure of a system and the degree of the molecular activity
Macroscopic energy energy related to motion and the influence of some external effects such as gravity, magnetism, electricity, surface tension
Enthalpy, h h = u + Pv = u + P Where, P = flow energy, energy per unit mass needed to move the fluid and maintain flow
For ideal gas, the internal energy and enthalpy can be expressed in terms of specific heat u = cv,ave T and h = cp,ave T Where, cv,ave = average specific heat at constant volume cp,ave = average specific heat at constant pressure For incompressible substance, h = u + P/ cave T + P/
SME 1313 Fluid Mechanics I
Coefficient of Compressibility
Coefficient of compressibility (also called the bulk modulus of compressibility or bulk modulus of elasticity) for fluids as (Pa) = - v P = P T V T In term of finite changes - P P (T=constant) v/v / Large , a large change in pressure is needed to cause a small fractional change in volume (incompressible e.g liquids)
SME 1313 Fluid Mechanics I
Coefficient of Compressibility
For an ideal gas, P = RT and (P/ )T = RT = P/ And thus, (Pa) ideal gas = P Coefficient of compressibility of an ideal gas is equal to its absolute pressure and it increases with increasing pressure Substituting = P into definition of the coefficient of compressibility and rearranging gives = P (T=constant) P The percent increase of density of an ideal gas during isothermal compression is equal to the percent increase in pressure
SME 1313 Fluid Mechanics I
Isothermal Compressibility
Isothermal compressibility is the inverse of the coefficient of compressibility = 1 = - 1 V = 1 (1/Pa) v P T P T Isothermal compressibility of fluid represents the fractional change in volume or density corresponding to a unit change in pressure
Coefficient of volume expansion provide information on variation of density of a fluid with temperature at constant pressure = - 1 (1/K) = 1 v T P v T P In term of finite changes v/v - / (P=constant) T T Large for a fluid means a large density change in density with temperature
SME 1313 Fluid Mechanics I
(v/T)P
20oC 100 kPa 1 kg 21oC 100 kPa 1 kg 20oC 100 kPa 1 kg 21oC 100 kPa 1 kg
The coefficient of volume expansion is a measure of the change in volume of a substance with temperature at constant pressure
SME 1313 Fluid Mechanics I
For ideal gas, the volume expansion coefficient at a temperature T is ideal gas = 1 (1/K) T Where, T=absolute temperature
The combined effects of pressure and temperature changes on volume change of a fluid can be determined by taking the specific volume to be a function of T and P Differentiating v=v(T,P) and using the definitions of compression and expansion coefficient and give dv = v dT + v dP =( dT dP) v T P P P The fractional change in volume (or density) due to changes in pressure and temperature can be expressed approximately as v = - T - P v SME 1313 Fluid Mechanics I
Problem 2-32
Problem 2-32 Water at 1 atm pressure is compressed to 800 atm pressure isothermally. Determine the increase in the density of water.Take the isothermal compressibility of water to be 4.80 x 10-5 atm-1
Example 2-3
Example 2-3 Consider water initially at 20oC and 1 atm. Determine the final density of water (a) if it is heated to 50oC at a constant pressure of 1 atm, and (b) if it is compressed to 100-atm pressure at constant temperature of 20oC. Take the isothermal compressibility of water to be =4.80x10-5 atm-1
Viscosity
Viscosity is a property that represents the internal resistance of a fluid to motion or the fluidity Consider a fluid layer between two very large parallel plates separated by distance l
dA N d y x N u=V Velocity V Area A Force F
l
Velocity profile M u=0
u(y)=(y/l)V
Behavior of a fluid in a laminar flow between two parallel plates when the upper plate moves with a constant velocity SME 1313 Fluid Mechanics I
Viscosity
A constant parallel force F is applied to the upper plate, the lower plate is held fixed The upper plate moves continuously at constant velocity under the influence of F The shear stress acting on the fluid layer is
F = A
Viscosity
Fluid in contact with lower plate has zero velocity (no-slip condition) In steady laminar flow, the fluid velocity between the plates varies linearly between 0 and V, and thus the velocity profile and the velocity gradient are
y u( y) = V l
Where,
and
du V = dy l
Viscosity
Viscosity
The rate of deformation of a fluid element is equivalent to the velocity gradient du/dy Fluids rate of deformation (and thus the velocity gradient) is directly to the shear stress
d dt
or
du dy
Newtonian fluids for fluids which its rate of deformation is proportional to the shear stress
Viscosity
In 1-D shear flow of Newtonian fluids, shear stress can be expressed by linear relationship du = dy Where, =coefficient of viscosity/dynamic(absolute) viscosity of the fluid, N.s/m2 (or Pa.s) Poise=0.1 Pa.s
SME 1313 Fluid Mechanics I
Viscosity
The force F required to move the upper plate at constant velocity of V while the lower plate remains stationary is
V F = A l
(N)
Viscosity
Viscosity
Oil
Shear stress, a
Viscosity=slope
a = du dy b
Water Air
Rate of deformation, du/dy
The rate of deformation (velocity gradient) of a Newtonian fluid is proportional to shear stress, and the constant of proportionality is the viscous
SME 1313 Fluid Mechanics I
Viscosity
Bingham plastic Shear stress, Pseudoplastic Newtonian
Dilatant
Rate of deformation, du/dy Variation of shear stress with the rate of deformation for Newtonian and nonNewtonian fluids (the slope of a curve at a point is the apparent viscosity of the fluid at that point)
SME 1313 Fluid Mechanics I
Viscosity
Viscosity is due to the internal frictional force that develops between different layers of fluids as they are forced to move relative to each other Gases
In a gas, molecular forces are negligible and the gas molecules at high temperatures move randomly at higher velocities This results in more molecular collisions per unit volume per unit time, thus greater resistance to flow
SME 1313 Fluid Mechanics I
Viscosity of Gas
aT 1 / 2 = 1+ b T
Where, T=absolute temperature (K) a and b = experimentally determined constants
Viscosity of Liquid
Liquids
Viscosity is due to the cohesive forces between the molecules At higher temperatures, molecules posses more energy, and they can oppose the large cohesive intermolecular forces more strongly The liquid viscosity is approximated as
= a10 b /(T c )
Where, T=absolute temperature (K) a, b and c = experimentally determined constants
SME 1313 Fluid Mechanics I
Gases
Temperature
The viscosity of liquids decreases and the viscosity of gases increases with temperature
SME 1313 Fluid Mechanics I
The viscosity of a fluid is to be measured by viscometer constructed of two 40-cm-long concentric cylinders (Fig. 218).the outer diameter of the inner cylinder is 12 cm, and the gap between the two cylinders is 0.15 cm. The inner cylinder is rotated at 300 rpm, and the torque is measured to be 1.8 N.m. Determine the viscosity of the fluid
SOLUTION The torque and the rpm of a double cylinder viscometer are given. The viscosity of the fluid is to be determined Assumptions 1) The inner cylinder is completely submerged in oil 2) The viscous effects on the two ends of the inner cylinder are negligible Analysis The velocity profile is linear only when the curvature effects are negligible, and the profile can be approximated as being linear in this case since l/R<<1
R
N=300 rpm Shaft
l
Fluid
Figure 2-18
SME 1313 Fluid Mechanics I
Surface Tension
Liquid droplets behave like small spherical balloons filled with the liquid, and the surface of the liquid acts like a stretched elastic membrane under tension. The pulling forces that causes this tensions acts parallel to the surface and is due to the attractive forces between the molecules of the liquid.
A molecule on the surface
A molecule inside the liquid Attractive forces acting on a liquid molecule at the surface and deep inside the liquid
SME 1313 Fluid Mechanics I
Surface Tension
The magnitude of the force per unit length is called surface tension, s (N/m)
Capillary Effect
Capillary effect is the rise or fall of a liquid in a smalldiameter tube inserted into liquid Capillaries is a narrow tubes or confined flow channels The curved free surface of a liquid in a capillary tube is called meniscus
a) Wetting fluid
b) Nonwetting fluid
Capillary Effect
Contact (or wetting) angle , is defined as the angle that the tangent to the liquid surface makes with the solid surface at the point of contact
<90o >90o
The liquid is to wet the surface The liquid is not to wet the surface
Cohesive forces is forces between like molecules (water-water), adhesive forces is forces between unlike molecules (water-glass). Water molecules are more strongly attracted to the glass molecules than they are to other water molecules, and thus water tends to rise along the glass surface
SME 1313 Fluid Mechanics I