Beruflich Dokumente
Kultur Dokumente
Smith Chart Tutorial Part1 To begin with we start with the definition of VSWR, which is the ratio of the reflected voltage over the incident voltage. The Reflection coefficient is simply the complex (ie has phase) version of VSWR:Define voltage standing wave ratio (VSWR)
V1e+j. .l
V2e-j. .l
T.L
ZL
L
= V2 e V = 2 e j 2 .l + j . .l V1 V1 e V2 V1
j . .l
At the load (l = 0) ; =
but this may be complex number if there is an instantaneous phase change which well call () on reflection.
V2
V 2 V 2 j = e ..... (a) L = 0 V1 V1
Phase Diagram
V1
Sheet 2 of 13
At L > 0 (L) = ( 0 )e j . =
V2 V1
e j ( 2 l )
V2 V1
V = V1 e + j . .l + V2 e j . .l V V j 2 .l ) = 1 + 2 e j 2 .l = 1 + e ( + j . .l V1 V1 e
At L = 0
OP
V = 1 + e j. V1
AP
||
Between 0 & 1
P Vmin = 1-|| ||
P C
-2.L
A Vmax = 1+||
Sheet 3 of 13
As we saw previously the crack diagram with a circle drawn between points A & C is the beginnings of a Smith chart less the constant resistance and reactance circles/lines.
VSWR =
|V| C C
Vmax
Length OP -crank diagram
Vmin
voltage v incident
L Lmin
At B - 2 . l min = -
= 2 . l min - =
4 . l min
Sheet 4 of 13
SmithChart - Impedance (Z) or Admittance Y chart (1) Crank diagram + constant resistance & constant reactance circles. (2) Graphical solution to the equation
Z ( in ) Zo
1+ 1
= e j ( 2 .l )
complex
= -2. .L ||
A = || = 0
|| = 1
Smith Chart
A is the matched point || = R=1 circle
0
Const r Const x
no reflection
Short circuit v=0,x=0
Open circuit x
O
X = 0 pure resistance
Sheet 5 of 13
Impedance is plotted on the smith chart by first normalising to the characteristic impedance of the system (usually 50 ohms). In a 50 ohm system the centre of the smith chart is a pure 50 ohms. For example say we wanted to plot an impedance of 150 + j75 First normalise ie 150/50 = 3 ; 75/50 = 1.5 normalised impedance = 3+ j1.5 So the real part of the impedance will lie somewhere along the r = 3 constant resistance circle ie:R=3 circle
Next we follow the constant reactance line at 0.75 to find the intersection of the r = 3 circle to get to our impedance point.
X=0.75 line
R=3 circle
3+j1.5
Sheet 6 of 13
Using the Smith Chart (1) Moving along the T.L = rotating around the Smith Chart.
FORWARDS
ZL
L
FORWARDS (TO LOAD)
BACKWARDS
BACKWARDS (FROM LOAD)
(2) Constant || or VSWR circles For a lossless line || & VSWR do not vary with L.
1+ VSWR = 1- S
Vmin
|| = 0 VSWR = 1
Vmax =
Vmax
|| = 1 VSWR =
Vmin =
Sheet 7 of 13
|V| B
= 4
lmin
Lmin
FORWARD by Lmin/g takes us the load.
Vmin
B
Lmin/g
ZL/Zo
(4) Reading Z from chart also can get || &
x
ZL
Sheet 8 of 13
(5)
Z 1+ = Zo 1
Z/Zo
| | 1
Admittance = Y/Y0 =
1 -||
Y/Yo
Z Y gives Zo Yo
Note Y0 =
1 Zo
Y = G + j. Conductance Susceptance
Note g =
Sheet 9 of 13
(6) To transform an impedance along a T.L, rotate around the VSWR circle:-
Z(in)
Zo
ZL
Lmin
BACKWARDS by Lmin/g takes us to Zin.
l/g
ZL/Zo
B
Vmin Lmin/g
Sheet 10 of 13
0.20
Therefore, assuming a frequency of say 1GHz the value of series inductance represented on the above Smith Chart is given by:-
Reactance (XL ) read from Smith chart = 0.5 - 0.2 = 0.3 wrt 50 L = N.XL 50 * 0.3 = = 2.38nH 2f 2 * 1E 9
Sheet 11 of 13
Therefore, assuming a frequency of say 1GHz the value of series capacitance represented on the above Smith Chart is given by:Reactance(XC ) read from Smith chart = 1.0 - 0.5 = 0.5 w.r.t 50 C = 1 1 = = 6.36pF 2f .N.XC 2 * 1E9 * 50 * 0.5
To represent shunt reactance we need to plot admittance onto the Smith Chart. It is easiest to use a Smith chart with both impedance (usually in black) lines and admittance lines (usually in red) on the same chart. Or you can rotate the Smith chart 180 degrees.
Sheet 12 of 13
0.2
Therefore, assuming a frequency of say 1GHz the value of shunt inductance represented on the above Smith Chart is given by:Admittance(YL ) read from Smith chart = (0.8 - 0.2) = 0.6mhos w.r.t 50 L = N 50 = = 13.26nH 2f * YL 2 * 1E9 * 0.6
Sheet 13 of 13
0.2
Therefore, assuming a frequency of say 1GHz the value of shunt inductance represented on the above Smith Chart is given by:-
Admittance (YC ) read from Smith chart = (1.0 - 0.2) = 0.8mhos w.r.t 50 C = YC 0.8 = = 2.5pF 2f * N 2 *1E 9 * 50