Beruflich Dokumente
Kultur Dokumente
Pgina 1 de 5
Desarmado y Armado
Alternator - Delco 21SI
Nmero de medio -SENR4757-04 Fecha de pu blicacin -01/02/2007 Fecha de actu alizacin -22/02/2007
i01336981
Alternator - Assemble
SMCS - 1405-016
Assembly Procedure
Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause problems in the future. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Table 1 Required Tools Part Number 1P-0510 Part Description Driver Gp Qty 1
https://10.144.4.9:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/... 03/06/2013
Pgina 2 de 5
Illustration 1
g00706948
1. Install bearing (28) into the rear frame. Use 1P-0510 Driver Gp .
Illustration 2
g00706939
2. Install rectifier (24) and install screw (23). Install capacitor (27). Install screw (25) and install insulated screw (26) .
Illustration 3
g00706922
3. Install regulator (20) and install screw (21). Install brush holder (18). Install screw (22) and install insulated screw (19) .
https://10.144.4.9:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/... 03/06/2013
Pgina 3 de 5
Illustration 4
g00706931
4. Install B+ terminal (11) and install connector strap (15). Install nut (16). Install R terminal (12) and install connector strap (13). Install diode assembly (14) and install insulated screw (17) .
Illustration 5
g00706884
5. Install stator (10) into rear frame (4). Install three nuts (9) .
https://10.144.4.9:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/... 03/06/2013
Pgina 4 de 5
Illustration 6
g00707145
6. The brushes (29) must be held in the depressed position in order to install the rotor in the rear frame. Depress brushes (29). Insert a piece of wire (30) through brush holder (18). Wire must extend through the back of the rear frame (4) for removal in step 9.
Illustration 7
g00706882
Illustration 8
g00706873
Note: Do not apply force to the inner race of bearing (7). To install the bearing, apply force to the outer race. 8. Install bearing (7) into the drive frame. It may be necessary to use a hydraulic press to install the bearing. Install retainer (6) and install three bolts (5) .
https://10.144.4.9:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/... 03/06/2013
Pgina 5 de 5
Illustration 9
g00706866
9. Position drive frame (3) over the rotor shaft. Carefully push the drive frame (3) to the rear frame (4). Align the marks on the frames that were made during disassembly. Install four bolts (2). To tighten bolts (2), refer to Specification, "Alternator" for the proper torque.
Illustration 10
g00706834
Note: Do not install the pulley while the rotor shaft is vertical. This may cause internal damage to the alternator. Install the pulley while the rotor shaft is horizontal. 10. Install fan (1) onto the rotor shaft. Install the pulley. Install the washer and install the nut. To tighten the nut, refer to Specification, "Alternator" for the proper torque. End By: Install the alternator on the machine. Refer to Disassembly and Assembly, "Alternator Install" for the machine that is being serviced.
Copyright 1993 - 2013 Caterpillar Inc. Todos los derechos reservados. Red privada para licenciados del SIS. Mon Jun 3 08:00:26 EST 2013
https://10.144.4.9:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/... 03/06/2013